Modern Forms PD-50748 Stacked Instrucciones de operación
- Tipo
- Instrucciones de operación
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
HARDWARE
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
INSTALLATION INSTRUCTION
507 - LED Pendant
PD-50748
Wire Connector
Qty: 3 pcs + 1 Extra
7EAC112201
P3
Junction Box Screw
Qty: 2 pcs + 1 Extra
7MPF0415C2
#8-32x5/8
Stainless Steel
Mounting Screw
Qty: 2 pcs + 1 Extra
7MPF041502 (AL)
4MPF041502BK (BK)
4MPF041502SB (BR)
5/32"-32x5/8
Stainless Steel
Wire Connector
Qty: 2 pcs + 1 Extra
7EAC140901
P1
A1 B1 C1 D1
2Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
CONNECTING THE WIRES (Fig. 2)
3. Remove the mounting screws (C1) from the xture.
4. Connect the driver input wires with supply wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured. If your outlet box
has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the
mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
*Requires Driver to be recessed within the junction box.
MOUNTING THE FIXTURE (Fig. 1)
5. Secure mounting back plate to the junction box using junction box screws (B1). The side of the mounting plate marked “GND”
must face out. Pull out the driver output wire.
6. Choose the number of down rods suitable of your application.
7. Thread the xture wire through the decorative stem, rods, swivel and canopy. Connect the canopy with swivel, rods, decorative stem and
xture body. Make sure all are tightened.
8. Connect the driver output wires with xture wire as
shown in Fig. 2, making sure that all wire connectors
(D1) are secured.
9. Place the xture over the mounting back plate and
secure it with mounting screws (C1).
10. The lamp arm and connecting rod can rotate 340
degrees; rotate them to your desired angles.
11. For slope ceiling application, rotate swivel at the top
of the stem to ensure luminaries are aiming down
(Fig. 3).
INSTALLATION INSTRUCTION
507 - LED Pendant
PD-50748
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring Fig. 3
Turn to down
Ø
5 3/8"
1 3/8"
1 3/4"
Mounting Screw
Junction Box Screw
Wire Connector
Ground Wire
Driver
Junction Box
Mounting Back Plate
Rods (3 x 12")
Rods (1 x 6")
Decorative Stem
Back Plate Dimensions
Swivel
Rotating Connecting Rod 340°
Wire Connector
Rotating Arm 340°
D1
C1
B1
A1
FIG. 1
-
1
-
2
Modern Forms PD-50748 Stacked Instrucciones de operación
- Tipo
- Instrucciones de operación
En otros idiomas
Documentos relacionados
-
Modern Forms PD-53728 Catalyst Instrucciones de operación
-
-
-
-
-
-
-
-
-