Modern Forms PD-54728 Kryptonite Instrucciones de operación

Modern Forms
Marca
Modern Forms
Modelo
PD-54728 Kryptonite
Tipo
Instrucciones de operación
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
HARDWARE
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
INSTALLATION INSTRUCTION
547 - LED Pendant
PD-54728, PD-54732, PD-54765
Wire Connector
Qty: 3 pcs + 1 Extra
7EAC112201
P3
Junction Box Screw
Qty: 2 pcs + 1 Extra
7MPF0415C2
#8-32x5/8
Stainless Steel
Mounting Screw
Qty: 3 pcs + 1 Extra
7MPF0308S1/*
.1'4#,#,
Y
Wire Connector
Qty: 2 pcs Per Driver
+ 1 Extra
7EAC140901
P1
A1 B1 C1 D1
2Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
547 - LED Pendant
PD-54728, PD-54732, PD-54765
Wire Connector
Back Plate Dimensions
Junction Box Screw
Mounting Screw
Driver
Rods (1 x 6")
Rods (12x 12")
Connect Tube
Glass
(RPL-GLA-54732)
Mounting Back Plate
Junction Box
Ground Wire
Wire
Connector
Rotating Body 340°
Connection Tube
A1
B1
C1
D1
FIG. 1 PD54732
PD54728 PD54765
Ø
4 3/4"
1 3/8"
1 3/4"
3Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
547 - LED Pendant
PD-54728, PD-54732, PD-54765
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screws (C1) from the xture.
4. Secure mounting plate to the junction box using junction box screws (B1). The side of the mounting plate marked “GND” must face out.
5. Choose number of rods suitable for your application. Thread the xture wire through the rods, swivel and canopy, connect swivel, rods and
xture body. Make sure all are tightened.
6. Thread the glass onto the xture.
CONNECTING THE WIRES (Fig. 2)
7. Cut the extra wire. Connect the Driver input/output wire with supply wires as shown in Fig. 2, making sure that all
wire connectors (A1) (D1) are secured. If your outlet box has a green or bare copper ground wire, connect the xture’s ground wire to it.
Otherwise, connect the xture’s ground wire directly to the mounting plate using the green screw provided. After wires are connected,
tuck them carefully inside the junction box.
8. Place the xture over the mounting back plate and secure with mounting screws (C1).
9. The connection tube can rotate 340 degrees; rotate it to your desired angles.
*GUIFDPOOFDUJPOUVCFDBOOPUCFIPMESPUBUFUIFDPOOFDUJPOUVCFVOUJMJUDBOCFGJYFE
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
3Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
547 - LED Pendant
PD-54728, PD-54732, PD-54765
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screws (C1) from the xture.
4. Secure mounting plate to the junction box using junction box screws (B1). The side of the mounting plate marked “GND” must face out.
5. Choose number of rods suitable for your application. Thread the xture wire through the rods, swivel and canopy, connect swivel, rods and
xture body. Make sure all are tightened.
6. Thread the glass onto the xture.
CONNECTING THE WIRES (Fig. 2)
7. Cut the extra wire. Connect the Driver input/output wire with supply wires as shown in Fig. 2, making sure that all
wire connectors (A1) (D1) are secured. If your outlet box has a green or bare copper ground wire, connect the xture’s ground wire to it.
Otherwise, connect the xture’s ground wire directly to the mounting plate using the green screw provided. After wires are connected,
tuck them carefully inside the junction box.
8. Place the xture over the mounting back plate and secure with mounting screws (C1).
9. The connection tube can rotate 340 degrees; rotate it to your desired angles.
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
Driver
I
nput
Out
put
Black
- Hot
White -
Neutral
Driver
I
nput
Out
put
Black
- Hot
White -
Neutral
- + - +
Black
- Hot
White -
Neutral
Fi
x
ture
- + - +
PD-54728 / PD-54765 Wiring Diagram see below
PD-54732 According to a single drive direct connection
  • Page 1 1
  • Page 2 2
  • Page 3 3

Modern Forms PD-54728 Kryptonite Instrucciones de operación

Modern Forms
Marca
Modern Forms
Modelo
PD-54728 Kryptonite
Tipo
Instrucciones de operación
Descargar PDF
informe

En otros idiomas

Documentos relacionados