WAC Lighting FM-113G2-35-WT Guía de instalación
- Tipo
- Guía de instalación
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER 3, 2015 9:26 AM
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
Flush Mount
FM-113, FM-115
WARNING
IMPORTANT: NEVER attempt any work without shutting off the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the fixture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction could invalidate the CSA listing of this fixture.
CAUTION When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation CSA du luminaire.
MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer depression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación
de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calificado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación
ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calificación
CSA esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
HARDWARE
B1 D1A1
Wire Connector
Qty: 3
Junction Box Screw
Qty: 2 + 1 Extra
Crossbar
Qty: 1
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER 3, 2015 9:26 AM
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
F1
A1
D1
C1
I1
B1
E1
L1
G1
Junction box
Connectors
Crossbar
Mounting
Screw
Keyholes
Ground Wire
Wires (Black, White)
Junction Box Screw
Barrier
Canopy
Diffuser
INSTALLATION INSTRUCTION
Flush Mount
FM-113, FM-115
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig.2 Wiring
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture, including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
CONNECTING THE WIRES (Fig. 2)
3. Connect the fixture input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured.
If your outlet box has a ground wire (I1) (Green or bare copper), connect the fixture’s ground wire to it.
After wires are connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1)
4. Secure crossbar (D1) to the junction Box (F1) using junction box screws (B1).
The side of the mounting plate marked “GND” must face out.
5. Place the canopy (L1) over the cross (D1) and secure with screws exposed
to engage keyholes in canopy (C1).
6. Twist lock the diffuser (G1) into the canopy (L1).
FIG 1
-
1
-
2
WAC Lighting FM-113G2-35-WT Guía de instalación
- Tipo
- Guía de instalación
En otros idiomas
Documentos relacionados
Otros documentos
-
Modern Forms WS-21724-CH Guía de instalación
-
-
-
-
-
-
-
-
-