Omcan SE-CN-0358 Manual de usuario

Revised - 08/06/2021

Toll Free: 1-800-465-0234

Fax: 905-607-0234

Email: [email protected]

www.omcan.com

14” Impulse Sealers

Models SE-CN-0358, 0361

Items 14432, 14433

Instruction Manual

2

Page

--------------------------------------------------------------------------- 3 - 4

--------------------------------------------------------------------------- 4 - 5

-------------------------------------------------------------------------- 5

--------------------------------------------------------------------------------------------- 6

------------------------------------------------------------------------------------ 6 - 7

-------------------------------------------------------------------------------- 7 - 8

----------------------------------------------------------------------------- 9 - 10

---------------------------------------------------------------------------- 11

------------------------------------------------------------------------------------------- 12 - 14

---------------------------------------------------------------------------- 15

Table of Contents

Section

General Information

Safety and Warranty

Technical Specications

Operation

Maintenance

Troubleshooting

Parts Breakdown

Electrical Schematics

Notes

Warranty Registration

Model SE-CN-0358 / Model SE-CN-0361

3

General Information

Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan

and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or

negligent use of this equipment. The product shall only be operated by someone over the age of 18, of

sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct

operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the

machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of

the machine while in operation.

CHECK PACKAGE UPON ARRIVAL

Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the

external packaging, open carton to ensure all ordered items are within the box, and there is no concealed

damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed),

please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may

initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be

lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse

for damaged products that were shipped collect or third party.

Before operating any equipment, always read and familiarize yourself with all operation and safety

instructions.

Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save

these instructions for future reference. Also save the original box and packaging for shipping the

equipment if servicing or returning of the machine is required.

---------------------------------------------------------------------------------------------------------------------------------------------------

Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et

Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne

ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de

plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour

utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication

de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine

ou des personnes à proximité de la machine pendant son fonctionnement.

VÉRIFIEZ LE COLIS DÈS RÉCEPTION

Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage

n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés

sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises

manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant

d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager

une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine

doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents

d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli

par un tiers transporteur.

4

Safety and Warranty

General Information

• This machine should only be installed and operated by trained personnel. Do not change the electrical

wiring of the machine.

• Read all instructions carefully and do not operate the machine until the operator has fully read this manual.

• Do not use the machine without the personal safety equipment.

• Keep hands, long hair, foreign objects, clothes and jewelry away from any moving parts.

• Do not leave the machine unattended while the unit is on or in operation.

• Always turn off and unplug the unit before performing any maintenance.

Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations

et les consignes de sécurité.

Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces

instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour

l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.

---------------------------------------------------------------------------------------------------------------------------------------------------

Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba

Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona

inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona

mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido

entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.

Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la

máquina mientras esta en el funcionamiento.

REVISE EL PAQUETE A SU LLEGADA

Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el

empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la

caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes

o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro

de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre

los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se

muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron

a recoger por terceros.

Antes de utilizar cualquier equipo, siempre leer y familiarizarse con todas las instrucciones de

operación y seguridad.

Omcan quisiera darles las gracias por la compra de esta máquina. Es de la máxima importancia para

guardar estas instrucciones para referencias en el futuro. También guarde la caja original y el embalaje

para envío del equipo si el mantenimiento o la devolución de la máquina es necesaria.

5

Technical Specications

Safety and Warranty

RESIDENTIAL USERS: Vendor assumes no liability for parts or labor coverage for component failure

or other damages resulting from installation in non-commercial or residential applications. The right

is reserved to deny shipment for residential usage; if this occurs, you will be notied as soon as

possible.

1 YEAR PARTS AND LABOR WARRANTY

Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule an Omcan authorized

service technician to repair the equipment locally.

Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not

improper use.

Please see https://omcan.com/disclaimer for complete info.

WARNING:

The packaging components (cardboard, polyethylene, and others) are classied as normal solid urban waste

and can therefore be disposed of without difculty.

In any case, for suitable recycling, we suggest disposing of the products separately (differentiated

waste) according to the current norms.

DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!

Model SE-CN-0358 SE-CN-0361

Description 14” seal bar - 2mm seal width 14” seal bar - 5mm seal width

Electrical 110V / 60Hz / 1

Weight 42 lbs. / 19 kgs.

Packaging Weight 45 lbs. / 20.4 kgs.

Dimensions 20.8” x 16.5” x 33.5” / 527 x 419 x 851mm

Packaging

Dimensions 21.5” x 31” x 10” / 546 x 787 x 254mm

Item Number 14432 14433

6

Maintenance

Never try to seal without bags. Don’t set the sealing time to the high grade without trial of the sealing bag.

Otherwise, the polymer cloth will be burned. If some plastics adheres to the polymer cloth, never try to scrape

it off. Slightly reduce the sealing time and seal the bag again. Release the pedal after the yellow lamp is off. It

is very important to remove the bag from one side to the other. The remains of the plastics will be cleared from

the polymer cloth with the bag.

REPLACEMENT OF THE HEATER

Turn off sealer and unplug from the wall. Loosen the screws of the plate pressing the polymer cloth, roll back

the cloth to expose the heater. Loosen the Bakelite boxes at both sides of the heater and take out the screws

on the copper block. The heater can now be removed. Replace it with a new one. The heater should always

be in tension with the function of the spring. The copper block should be replaced if it is oxidized, to ensure

it has a good connection with the heater. Pay close attention when xing the heater so that the polymer cloth

below is at (no wrinkles are allowed). The heater must have a excellent isolation. Otherwise the heater will be

Operation

ADJUSTMENT AND USAGE OF IMPULSE SEALER

Connect to 110V power source according to the indication label on the machine. Switch on the power, the red

light will turn on. Adjust the sealing time according to the materials and the thickness of the bags to be sealed.

The sealing time should be adjusted to around grade 1 before sealing. Put the opening of the bag between

the heat sealers, step down on the pedal and the yellow lamp lights. Take out the sealed bag after the yellow

lamp is off. If the seal is not tight enough, lengthen the sealing time. Try sealing the bag several times until it is

sealed well with clearness and no wrinkles. Seal the bag at this measured time and temperature. The cooling

time should not be too short, otherwise wrinkles will be the result. The longer the sealing time, the longer the

cooling time.

Fig. 1 - Diagram

of the control

panel for the

impulse sealer

7

Troubleshooting

Problem Causes and Solution

The seal is not good. Lengthen the sealing time if it is not tight enough. Shorten the sealing

time if the seal is melted or if the melted seal is creased by not being

pressed tightly.

The seal is wrinkled. 1. The problem may be overheating. In this case, shorten the

sealing time.

2. The problem may be insufcient time for cooling. In this case,

lengthen the cooling time.

The temperature rises when working

for some time.

It is normal that the temperature of the machine rises because the

unit absorbs heat during operation. Shorten the sealing time slightly

to balance the heat.

The power lamp does not light and

the sealer does not work.

Check if the power switch is on and if the fuse is damaged.

Maintenance

damaged because of the short-circuiting.

REPLACEMENT OF THE POLYMER CLOTH

Turn off sealer and unplug from the wall. Remove the screws and the plates above the polymer cloth, loosen

the shaft of the polymer cloth roll, pull out the cloth and cut out the burned part. Reassemble the plates and

screws, tighten the roll shaft. No wrinkles are allowed in the polymer cloth, otherwise the seal quality will be

affected.

REPLACEMENT OF THE MICRO-SWITCH

Turn off sealer and unplug from the wall. There is one micro-switch at the side of the machine head. It must be

replaced when it is damaged. The adjustment of the pressing pole for micro-switch are as follows:

• Put 1mm thick carton between the upper and lower and lower pressing arms, check if the micro-switch is

pressed and if there is a “click” from the switch.

• If it is not pressed, adjust down the pressing pole or tighten the nut until the switch is pressed 1-2mm down

when it works.

• Always keep the sealing surface clean. Otherwise, the remains in the sealing surface will shorten the life of

the heater and the life of the polymer cloth.

• When working, never try to clean the sealing surface with wet cloth.

• After long time usage, the rubber in the upper pressing arm must be checked if it is still at and straight.

Otherwise, the seal quality will be affected.

• Often add lubricating oil into the moving parts.

• All parts in the machine should not be disassembled regularly.

8

Troubleshooting

The power lamp lights but the sealing

lamp is off and the sealer does not

work.

Step down on the pedal to check if the micro-switch works. Adjust if

necessary (see “REPLACEMENT OF MICRO-SWITCH).

The sealer is always electried when

the power is switched on.

Switch the power off at once. Check the status of the micro-switch.

Adjust if necessary (see “REPLACEMENT OF MICRO-SWITCH).

9

Parts Breakdown

Model SE-CN-0358 14432

Model SE-CN-0361 14433

10

Parts Breakdown

Model SE-CN-0358 14432

Model SE-CN-0361 14433

Item No. Description Position Item No. Description Position Item No. Description Position

75287 Machine Base for 14432, 14433 KS1 75311 Upper Sealing Shelf for 14432, 14433 KS25 75341 Touching Board for 14432, 14433 KS55-56

75288 Bolt for 14432, 14433 KS2 75312 Tetrauorohydrazine Convention for

14432, 14433 KS26 75342 Switch Shelf for 14432, 14433 KS57-58

75289 Pedal Board for 14432, 14433 KS3 75313 Flexible Mat for 14432, 14433 KS27 75345 Buttery Nuts for 14432, 14433 KS59

75290 Flat Washer for 14432, 14433 KS4 75314 Inner Hex Screw and Nut for 14432,

14433 KS28 75346 Pressor for 14432, 14433 KS60

75291 Nut for 14432, 14433 KS5 75315 Flexible Mat for 14432, 14433 KS29 75347 Bolt for 14432, 14433 KS61

75292 Bolt for 14432, 14433 KS6 75316 Flat Washer for 14432, 14433 KS30 75348 Insulated Pad for 14432, 14433 KS62

75293 Adjusting Bolt for 14432, 14433 KS7 75317 Tetrauorohydrazine Convention for

14432, 14433 KS31 75349 Bolt for 14432, 14433 KS63

75294 Buttery Nut for 14432, 14433 KS8 75318 Bolt Groups for 14432, 14433 KS32 75350 Countersink Flat Head Screws for

14432, 14433 KS64

75295 Bolt Groups for 14432, 14433 KS9 75319 Upper Sealing Silicon Fasten Block for

14432, 14433 KS33 75351 Heater for 14432, 14433 KS65

75296 Pedal Board Tie for 14432, 14433 KS10 17737 Silicon Rubber for 14432, 14433 KS34 75352 Insulated Pad for 14432, 14433 KS66

75297 Connecting Nut for 14432, 14433 KS11 75321 Spring for 14432, 14433 KS35 75353 Lower Sealing Fasten Base for 14432,

14433 KS67

75298 Coupling Tie for 14432, 14433 KS12 75322 Inner Hex Screw and Nut for 14432,

14433 KS36 75354 Polymer Pressor for 14432, 14433 KS68

75299 Upright Column Base for 14432, 14433 KS13 75323 Small Connecting Board for 14432, 14433 KS37 75355 Cross Recessed Pan Head Screw for

14432, 14433 KS69

75300 Machine Cover for 14432, 14433 KS14 75324 Flexible Pin for 14432, 14433 KS38 75356 Fasten Board of Working Table for

14432, 14433 KS70

75301 Nut for 14432, 14433 KS15 75325 Tie for 14432, 14433 KS39 75357 Flat Cushion for 14432, 14433 KS71

75302 Screw and Flat Gasket for 14432, 14433 KS16 75326 Rubber Cushion for 14432, 14433 KS40 75358 Bolts Groups for 14432, 14433 KS72

75303 Wire Guider for 14432, 14433 KS17 75327 Washer for 14432, 14433 KS41 75359 Flat Mat for 14432, 14433 KS73

75304 Cross Recessed Pan Head Screw for

14432, 14433 KS18 75328 Cap Nuts for 14432, 14433 KS42 75360 Bolts Groups for 14432, 14433 KS74

75305 Transformers and Back Cover for 14432,

14433 KS19 75329 Plastic Cover for 14432, 14433 KS43 75361 Flat Mat for 14432, 14433 KS75

75306 Bolt for 14432, 14433 KS20 75364 Ceramic Base for 14432, 14433 KS44-50 75358 Bolt Groups for 14432, 14433 KS76

75307 Operation Panel for 14432, 14433 KS21 75337 Polymer for 14432, 14433 KS51 75360 Bolt Groups for 14432, 14433 KS77

75308 Countersink Screw for 14432, 14433 KS22 75338 Axles for Polymer for 14432, 14433 KS52 75364 Ceramic Base for 14432, 14433 KS78-84

75309 Bolt Groups for 14432, 14433 KS23 75339 Buttery Nut for 14432, 14433 KS53 75329 Plastic Cover for 14432, 14433 KS85

75310 Tetrauorohydrazine Convention for

14432, 14433 KS24 75340 Hold-Down Plate for 14432, 14433 KS54 72308 Screw and Pin Assembly for 14432,

14433

11

Electrical Schematics

Model SE-CN-0358 14432

Model SE-CN-0361 14433

12

Notes

________________________________________________________________________________________

13

Notes

________________________________________________________________________________________

14

Notes

________________________________________________________________________________________

15

Warranty Registration

Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación,

cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:

Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la

carte au niveau de la perforation, puis l’envoyer à l’adresse spécié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:

Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at

the perforation and then send to the address specied below. You can also register online by visiting:

OMCAN

PRODUCT WARRANTY REGISTRATION

3115 Pepper Mill Court,

Mississauga, Ontario

Canada, L5L 4X5

https://omcan.com/warranty-registration/

or email to: [email protected]

Purchaser’s Information

Name: Company Name:

Address:

Telephone:

City: Province or State: Postal or Zip: Email Address:

Country: Type of Company:

Restaurant Bakery Deli

Dealer from which Purchased: Butcher Supermarket Caterer

Dealer City: Dealer Province or State: Institution (specify):

Invoice: Other (specify):

Model Name: Model Number: Serial Number:

Machine Description:

Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):

Would you like to extend the warranty? Yes No



Por correo en Canadá

Pour postale au Canada

For mailing in Canada

Por correo en los EE.UU.

Pour diffusion aux États-Unis

For mailing in the US

OMCAN

PRODUCT WARRANTY REGISTRATION

4450 Witmer Industrial Estates, Unit 4,

Niagara Falls, New York

USA, 14305

Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan

Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North

American food service industry. Our success over these many years can be attributed to our commitment

to strengthen and develop new and existing relationships with our valued customers and manufacturers.

Today with partners in North America, Europe, Asia and South America, we continually work to improve

and grow the company. We strive to offer customers exceptional value through our qualied local sales

and service representatives who provide convenient access to over 5,000 globally sourced products.

Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et

matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces

nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles

et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en

Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et

développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à

nos ventes locales qualiées et des représentants de service qui offrent un accès facile à plus de 5000

produits provenant du monde entier.

Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros

de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir

a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos

clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan

continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor

excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un

fácil acceso a más de 5,000 productos con origen a nivel mundial.

Omcan SE-CN-0358 Manual de usuario

Omcan SE-CN-0358 Manual de usuario

En otros idiomas

Documentos relacionados

Otros documentos