Yamaha DVD-S700 Manual de usuario

Categoría
Reproductores de DVD
Tipo
Manual de usuario
DVD/VIDEO CD/CD PLAYER
DVD-S700
Before attempting to connect, operate or adjust this product,
please read this Operating Instructions manual completely.
Please save this manual.
Operating Instructions
2
Safety information
CAUTION:
DVD/VIDEO CD/CD PLAYER IS A CLASS 1
LASER PRODUCT. HOWEVER THIS DVD/VIDEO
CD/CD PLAYER USES A VISIBLE LASER BEAM
WHICH COULD CAUSE HAZARDOUS RADIA-
TION EXPOSURE IF DIRECTED. BE SURE TO
OPERATE THE DVD/VIDEO CD/CD PLAYER
CORRECTLY AS INSTRUCTED.
WHEN THIS DVD/VIDEO CD/CD PLAYER IS
PLUGGED TO THE WALL OUTLET, DO NOT
PLACE YOUR EYES CLOSE TO THE OPENING
OF THE DISC TRAY AND OTHER OPENINGS TO
LOOK INTO THE INSIDE OF THIS PLAYER.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE.
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, AND ANNOYING INTERFERENCE, USE
THE RECOMMENDED ACCESSORIES ONLY.
THIS DEVICE IS INTENDED FOR CONTINUOUS
OPERATION!
(Back of product)
CAUTION -LASER RADIATION WHEN OPEN.
DO NOT STARE INTO BEAM.
ATTENTION-RAYONNEMENT LASER EN CAS D'OUVERTURE.
NE PAS REGARDER DANS LE FAISCEAU.
VORSICHT -LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET.
NICHT IN DEN STRAHL BLICKEN.
ADVARSEL -LASERSTRÅLING VED ÅBNING.
SE IKKE IND I STRÅLEN.
ADVARSEL -LASERSTRÅLING NÅR DEKSEL ÅPNES.
STIRR IKKE INN I STRÅLEN.
VARNING -LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD.
STIRRA EJ IN I STRÅLEN.
VARO! -AVATTAESSA OLET ALTTIINA LASERSÄTEILYLLE.
ÄLÄ TUIJOTA SÄTEESEEN.
(Inside of product)
CLASS 1
LASER PRODUCT
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is called
the standby mode.
In this state, this unit is designed to consume a very
small quantity of power.
Note:
For Continental Europe, United Kingdom and
Australia models
This unit can be used only where the power supply
is AC 220240 V, 50 Hz. It cannot be used else-
where.
For other models
This unit can be used only where the power supply
is AC 110240 V, 50/60 Hz. It cannot be used else-
where.
3
Caution for AC mains lead (For United Kingdom)
For your safety please read the following text carefully
This appliance is supplied with a moulded three pin mains
plug for your safety and convenience.
A 5 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the
replacement fuse has a rating of 5 amps and that it is ap-
proved by ASTA or BSI to BS 1362.
Check for the ASTA mark ! or the BSI mark " on the body
of the fuse.
If the plug contains a removable fuse cover you must ensure
that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your local
dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR
THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE
SHOULD BE REMOVED AND THE PLUG CUT OFF AND
DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK
IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP
SOCKET.
If a new plug is to be fitted please observe the wiring code as
shown below.
If in any doubt please consult a qualified electrician.
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an ap-
propriate 3 pin plug fitted. For details, refer to the instructions
described below.
Note: The plug severed from the mains lead must be de-
stroyed, as a plug with bared flexible cord is hazardous if en-
gaged in a live socket outlet.
IMPORTANT
The wires in this mains lead are coloured in accordance with
the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this appliance
may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal in the plug which is marked with the letter N or co-
loured BLACK.
The wire which is coloured BROWN must be connected to
the terminal in the plug which is marked with the letter L or
coloured RED.
Under no circumstances should either of these wires be con-
nected to the earth terminal of the three pin plug, marked with
the letter E or Earth Symbol #.
How to replace the Fuse
ÁThere are two types of the supplied AC Mains Lead: ) and
* as shown below.
1 Open the fuse compartment with a screwdriver.
2 Replace the fuse and fuse cover.
TYPE )
TYPE *
12
12
4
Dear Customers
May we take this opportunity to thank you for purchasing this
YAMAHA DVD/VIDEO CD/CD player.
We strongly recommend that you carefully study the Operat-
ing Instructions before attempting to operate the unit and that
you note the listed precautions.
Features
È DVD: a completely new dimension in video
entertainment
ÁSubtitles may be displayed in one of a maximum of 32 lan-
guages
\
.
ÁThe audio soundtrack can be heard in up to 8 languages
\
.
ÁThe multi-angle function allows you to choose the viewing
angle of scenes which were shot from a number of different
angles. (Limited to DVD recorded with multiple camera an-
gles.)
\
The number of the languages recorded is dependent on the
software.
È High quality digital audio
ÁThe Dolby Digital (AC-3)/MPEG 1/2 25.1ch audio/Linear
PCM decoder is built into the player which makes it possible
to enjoy Multi-Channel Surround sound.
ÁWith the linear PCM sound of a 48 kHz/16 bit through
96 kHz/24 bit, audio quality exceeding that of CDs becomes
possible.
È Many convenient features
ÁGUI (Graphical User Interface) screens for showing the disc
information or player information and providing access to
many major functions of this unit
ÁProgramming of up to 5 scenes in memory (markers)
ÁParental lock settings to prevent play of discs unsuitable for
some audiences [DVD only]
È Compatible with PAL DVD (Video CD) and
NTSC DVD (Video CD)
ÁThis player can play discs recorded in either PAL or NTSC
format.
For Continental Europe, United Kingdom and Australia
models
However, the player must be connected to a PAL TV which
is capable of receiving PAL 525/60 system to play both PAL
DVD (Video CD) and NTSC DVD (Video CD).
For other areas models
However, the player must be connected to a Multi-system
TV to play both PAL DVD (Video CD) and NTSC DVD
(Video CD). The use of a Multi-system TV is recommended.
È Compatible with Video CD and CD as well as
DVD
È Disc formats supported by this player
The unit can play back discs bearing any of the following
marks:
Accessories
Please check and identify the
supplied accessories.
Remote control
unit . . . . . . . . . . . . . . 1
Batteries . . . . . . . . . 2
for remote control unit
[size AA (R6P)]
AC mains lead . . . . . 1
(For United Kingdom model)
AC mains lead . . . . . 1
(For Australia model)
AC mains lead . . . . . 1
(For Continental Europe
models and other models)
Video/audio
cord . . . . . . . . . . . . . 1
DVD
[8 cm disc/
12 cm disc]
Video CD
[8 cm disc/
12 cm disc]
CD
[8 cm disc/
12 cm disc]
5
Table of contents
Getting Started:
Safety information . . . . . . . . . . . . . . . . . . . . . 2
Caution for AC mains lead
(For United Kingdom) . . . . . . . . . . . . . . . . . . . . 3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Selecting the type of disc for the type of the
connected TV
(For other areas) . . . . . . . . . . . 6
Control reference guide . . . . . . . . . . . . . . . . . 7
Front panel display . . . . . . . . . . . . . . . . . . . . . 9
Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Remote control preparation. . . . . . . . . . . . . . 13
Before enjoying DVD/Video CD/CD . . . . . . . . 14
Basic Operation:
Basic play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ÁBasic play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ÁStopping play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
ÁSkipping ahead or back . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Rapid advance (Rapid reverse) . . . . . . . . . . . 17
Still picture (Pause) . . . . . . . . . . . . . . . . . . . . 17
Frame advance
[DVD/Video CD] . . . . . . . . . . . . . 17
Slow-motion play
[DVD/Video CD] . . . . . . . . . . . 18
Enjoying Video CDs with playback control
without using menus
[Video CD only] . . . . . . 18
Operation Using GUI Screens:
General information about GUI screens . . . . 19
ÁCommon procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Detailed descriptions of each GUI icon . . . . 20
ÁScreen for disc information . . . . . . . . . . . . . . . . . . . . . . . . 20
ÁScreen for player information . . . . . . . . . . . . . . . . . . . . . . 21
ÁScreen for slow-motion play and rapid advance
(reverse) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Advanced Operation:
Program play [Video CD/CD] . . . . . . . . . . . . . . . 22
Random play
[Video CD/CD] . . . . . . . . . . . . . . . 23
Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
ÁRepeat viewing (listening) . . . . . . . . . . . . . . . . . . . . . . . . 24
ÁRepeating sections between two specific points
(A-B repeat) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Storing markers in memory to be viewed
(listened) again . . . . . . . . . . . . . . . . . . . . . . 26
ÁStoring a marker in the memory . . . . . . . . . . . . . . . . . . . . 26
ÁRecalling/clearing a marker . . . . . . . . . . . . . . . . . . . . . . . 26
Changing subtitle language [DVD only] . . . . . . 27
Changing audio soundtrack language
[DVD only] . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Switching vocals ON or OFF for Karaoke
discs
[DVD/Video CD] . . . . . . . . . . . . . . . . . . . 28
Viewing from another angle
[DVD only] . . . . . . 29
Using a title menu
[DVD only] . . . . . . . . . . . . . . 30
Using a DVD menu
[DVD only] . . . . . . . . . . . . . 30
Initial Settings:
Initial settings . . . . . . . . . . . . . . . . . . . . . . . . . 31
ÁCommon procedures of initial settings . . . . . . . . . . . . . . . 31
ÁSelecting disc languages [DVD only] . . . . . . . . . . . . . . . . 32
ÁSelecting rating level [DVD only] . . . . . . . . . . . . . . . . . . . 33
ÁSelecting language of On-Screen Display menu . . . . . . . 34
ÁSwitching the On-Screen Display ON or OFF . . . . . . . . . 35
ÁSelecting the display brightness . . . . . . . . . . . . . . . . . . . . 35
ÁSelecting TV screen type . . . . . . . . . . . . . . . . . . . . . . . . . 36
ÁSelecting digital output . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
ÁSpeaker setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
ÁOther settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
For Your Reference:
Disc handling and maintenance . . . . . . . . . . 42
Language code list . . . . . . . . . . . . . . . . . . . . . 43
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 44
Self-diagnosis display function. . . . . . . . . . . 45
Definition of terms . . . . . . . . . . . . . . . . . . . . 46
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 47
Region Management
Information. . . . . . . . . . . . . . . . . . Back cover
6
Precautions
Please read these precautions before operating this unit.
È Mains lead protection
To avoid any malfunctions of the unit, and to protect against
electric shock, fire or personal injury, please observe the fol-
lowing.
ÁHold the plug firmly when connecting or disconnecting
the AC mains lead to this unit.
ÁDo not connect or disconnect the AC mains lead when
your hands are wet.
ÁKeep the AC mains lead away from heating appliances.
ÁNever put any heavy object on the AC mains lead.
ÁDo not attempt to repair or reconstruct the AC mains
lead in any way.
ÁRemove dust, dirt, etc. on the plug at regular intervals.
ÁIf the unit has been dropped or otherwise damaged, set
the unit to the standby mode and disconnect the AC
mains lead.
ÁIf smoke, malodors or noises are emitted from the unit,
set the unit to the standby mode and disconnect the AC
mains lead.
È Placement
Avoid placing the unit in areas of:
Ádirect sunlight or heating radiators, or closed automobiles
Áhigh temperature (over 35uC) or high humidity (over 90%)
Áexcessive dust
Ávibration, impact or where the surface is tilted
As the internal parts may be seriously damaged.
È Non-use periods
When the unit is not being used, switch the unit to the stand-
by mode.
When left unused for a long period of time, the unit should be
unplugged from the household AC outlet.
È No fingers or other objects inside
ÁTouching internal parts of this unit is dangerous, and may
cause serious damage to the unit. Do not attempt to disas-
semble the unit.
ÁDo not put any foreign object on the disc tray.
È Keep away from water and magnets.
ÁKeep the unit away from flower vases, tubs, sinks, etc. If liq-
uids are spilled into the unit, serious damage could occur.
ÁNever bring magnetic objects such as speakers near to this
unit.
È Stacking
ÁPlace the unit in a horizontal position, and do not place any-
thing heavy on it.
ÁDo not place the unit on amplifiers or other equipment which
may become hot.
È Condensation
Moisture may form on the lens in the following conditions
Áimmediately after a heater has been turned on.
Áin a steamy or very humid room.
Áwhen the unit is moved from a cold environment to a warm
one.
If moisture forms inside this unit, it may not operate properly.
In this case, turn on the power and wait about one hour for
the moisture to evaporate.
È If there is noise interference on the TV while a
broadcast is being received
Depending on the reception condition of the TV, interference
may appear on the TV screen while you are watching a TV
broadcast and the unit is left on. This is not a malfunction of
the unit or the TV. To watch a TV broadcast, switch this unit
to the standby mode.
Selecting the type of disc for the
type of connected TV
(For other models)
Both DVDs and Video CDs have the material recorded in the
PAL and NTSC systems. Refer to the table below to select
the correct disc type for the type of connected TV.
È Connecting to the Multi-system TV
Disc
PAL
NTSC
TV Monitor
Played in the PAL
system.
Played in the NTSC
system.
È Connecting to the NTSC TV
È Connecting to the PAL TV
Note:
When a disc which does not comply with Video CD standard
is played, the bottom part of the picture may disappear.
Disc
PAL
NTSC
TV Monitor
No clear images are
shown on the screen.
Played in the NTSC
system.
Disc
PAL
NTSC
TV Monitor
Played in the PAL
system. However, the
initial settings and
Video CDs Program
Play functions cannot
be used.
No clear images are
shown on the screen.
7
Control reference guide
Main unit
Page
g Remote control signal sensor. . . . . . . . . . . . . . . . . . . 13
h Display window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
i OPEN/CLOSE button . . . . . . . . . . . . . . . . . . . . . . . . . . 14
j SKIP buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 16
k Disc tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
l STOP button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
m STILL/PAUSE button . . . . . . . . . . . . . . . . . . . . . . . . . . 17
n PLAY button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
STANDBY/ON
f OPEN/CLOSE
DVD / VIDEO CD / CD
NATURAL SOUND DVD PLAYER DVD-S700
STOP STILL/PAUSE PLAY
:
SKIP
;
D I G I T A L
1 23 546
7
098
Page
e STANDBY/ON button . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Press to switch the unit to ON from Standby mode or vice
versa. In standby mode, the unit is still consuming a small
amount of power.
Standby mode
In this state, this unit consumes a very small quantity
of power to receive infrared-signals from the remote
control transmitter.
f STANDBY indicator
When the unit is connected to the AC mains supply, this
indicator lights up in standby mode and goes out when the
unit is turned on.
8
Control reference guide
Remote control unit
Page
e POWER */I button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
f STOP button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
g SKIP buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 16
h TITLE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 30
i Cursor buttons/SELECT button . . . . . . . . . . . . . . . . . 15
j ON SCREEN button . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
k SUBTITLE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
l MARKER button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
m PLAY MODE button . . . . . . . . . . . . . . . . . . . . . . . . 22, 23
n REPEAT button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
o A-B button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
p SET UP button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
q STILL/PAUSE button . . . . . . . . . . . . . . . . . . . . . . . . . . 17
r OPEN/CLOSE button . . . . . . . . . . . . . . . . . . . . . . . . . . 14
s PLAY button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
t SLOW/SEARCH buttons . . . . . . . . . . . . . . . . . . . . 17, 18
u MENU button . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 18, 30
v RETURN button . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 19
w AUDIO button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
x ANGLE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
y Numeric buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ÁTo select a 2-digit number
Example: To select track 23
Press X10, 2 and then 3.
z CLEAR button. . . . . . . . . . . . . . . . . . . . . . . 19, 23, 26, 32
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP
I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
1
2
4
5
6
7
8
9
0
o
p
3
r
s
u
x
y
z
v
w
t
q
9
DVD
PROG.
ANGLE
96kHz 24bit
1 3 5 642
89 p0o q
r
s
t
u
v
w
x
y
z
DVD
DVD
DVD
DVD
|
{
7
Front panel display
e Rotates during play.
Rotates fast clockwise or counterclockwise
during rapid advance (reverse). (See page 17.)
Rotates slowly clockwise or counterclockwise
during slow-motion play.
[DVD/Video CD] (See page 18.)
Illuminates in the stop mode.
f Illuminates during playback.
Flashes when the RESUME function is ON.
(See page 16.)
g Illuminates during repeat play. (See pages 24 and 25.)
h Illuminates in the pause mode. [CD] (See page 17.)
i Indicates the chapter number. [DVD]
Indicates the track number. [Video CD/CD]
j Indicates the total playing time when the disc tray is
closed. [Video CD/CD]
Indicates the elapsed playing time from the start of the
title/track during play.
k Indicates the current audio channel information re-
corded in the disc (e.g. 2ch or 5.1ch).
l Illuminates when a DVD is loaded.
m Illuminates in the still picture mode.
[DVD/Video CD] (See page 17.)
n Illuminates during program play. [Video CD/CD]
(See pages 22 and 23.)
o Illuminates when it is possible to switch the angle
[DVD] (See page 29.)
p Illuminates when Linear PCM of 96 kHz sampling is
being played.
q Illuminates when Linear PCM of 24 bit is being played.
r Illuminates when the disc tray is open.
s Illuminates when the disc tray is being closed (re-
tracted).
t Illuminates during play of a DVD.
u Illuminates during play of an interactive DVD.
\
v Illuminates during play of a Karaoke DVD.
w Illuminates during play of an interactive Karaoke
DVD.
\
x Illuminates during play of a Video CD.
y Illuminates during play of a Video CD with playback
control.
z Illuminates during play of a CD.
{ Illuminates when playback is impossible.
ÁDVDs for which playback is prohibited by the setup Rat-
ings. (See page 33.)
For Continental Europe and United Kingdom models
ÁDVDs with Region No. other than 2 or ALL.
For Australia model
ÁDVDs with Region No. other than 4 or ALL.
For other models
ÁDVDs with Region No. other than 3 or ALL.
(See page 42.)
| Illuminates when no disc is loaded.
\
An interactive DVD is a DVD software which includes multi-
ple angles, stories and so on.
10
Connection
Never plug in this unit and other components until all connections are completed.
ÁBe sure that the colors of the connectors and plugs match up when connecting the cord.
ÁRead through the instructions for the equipment to be connected.
Connecting to an AV amplifier containing Dolby Digital (AC-3)/MPEG 1/2 2–5.1ch audio
decoder
When DVDs recorded in Dolby Digital or MPEG audio are played, Dolby Digital bitstream or MPEG audio bitstream is output from
the players OPTICAL digital audio output connector or COAXIAL digital audio output connector. When the player is connected to a
Dolby Digital decoder or MPEG audio decoder, you can enjoy theater-quality audio in your home. [An optical digital cable or coaxial
audio cable (both optional) is required when an optional Dolby Digital decoder or MPEG audio decoder is used.]
Notes:
ÁDuring DVD play, the TV volume may be at a lower level
than during TV broadcasts, etc. If this is the case, adjust the
volume to the desired level.
ÁIf the DVD player is connected to the TV through a video
cassette recorder, the picture may not be played back nor-
mally with some DVDs. If this is the case, do not connect
the player via the VCR.
PCM/U DIGITAL
MPEG
COAXIAL
DIGITAL
OPTICAL
L
AUDIO OUT VIDEO OUT
SUBWOOFER
CENTER SURROUND
6CH DISCRETE
MIXED 2CH
VIDEO
MAIN
AC IN
S VIDEO
L
R R
R
L
2
1
DVD/
LD
DVD/
LD
VIDEO SIGNAL
VIDEO
S-VIDEO
SIGNAL
L
AUDIO
R
DVD/LD
OPTICAL
COAXIAL
Coaxial audio
cable (optional)
Optical digital
cable (optional)
Video/audio
cord
(supplied)
S-video cord
(optional)
TV set (optional)
AV amplifier with
Dolby Digital (AC-3)/
MPEG audio decoder
(optional)
DVD/VIDEO CD/CD player
S-video output
connector
The S (separate) video output connector separates the color
(C) and luminance (Y) signals before transmitting them to the
TV set in order to achieve a sharper picture.
Use the S-video cord (optional) when connecting the player
to a TV set equipped with an S-video input connector for the
best picture clarity possible.
To power
outlet
AC mains
lead
(supplied)
\
The configuration of the plug differs according to
the area.
11
Connection
Notes when connecting the optical digital cable
ÁRemove the dust protection cap from the connector and
connect the cable firmly so that configurations of both the
cable and the connector match.
ÁKeep the dust protection cap and always reattach the cap
when not using the connector to protect against dust.
Disc
DVD
Video
CD
CD
Sound
recording
format
Dolby Digital
(AC-3)
Linear PCM
(48/96 kHz
16/20/24 bit)
MPEG
MPEG 1
Linear PCM
Optical/coaxial digital
audio output from
connector
Dolby Digital bitstream
(25.1ch) or PCM (2ch)
(48 kHz/16 bit)
\1
Linear PCM (2ch)
(48 kHz sampling/16 bit
only)
\2
or no output
\1
MPEG audio bitstream or
PCM (2ch) (16 bit)
\1
PCM
(44.1 kHz sampling)
Linear PCM
(44.1 kHz sampling)
\1
The type of audio output from the connector can be select-
ed by the initial settings. (See page 37.)
\2
Sound having 96 kHz sampling converted into 48 kHz sam-
pling when it is output from the units optical/coaxial digital
audio output connector.
For your reference:
ÁDolby Digital (AC-3) is a digital sound compression tech-
nique developed by the Dolby Laboratories Licensing Cor-
poration.
Supporting 5.1-channel surround sound, as well as stereo
(2-channel) sound, this technique enables a large quantity
of sound data to be efficiently recorded on a disc.
ÁLnear PCM is a signal recording format used in CDs. While
audio CDs are recorded in 44.1 kHz/16 bit, DVDs are re-
corded in 48 kHz/16 bit up to 96 kHz/24 bit.
ÁIf you have a Dolby Pro Logic Surround decoder, you will
obtain the full benefit of Pro Logic from the same DVD mov-
ies that provide full 5.1-channel Dolby Digital soundtracks,
as well as from titles with the Dolby Surround mark.
Concerning the audio output from the units optical/coax-
ial digital audio output connector
Dust protection cap
Caution for the optical/coaxial digital au-
dio output connector:
ÁDo not connect an amplifier (with an optical/coaxi-
al digital input connector) which does not contain
the Dolby Digital (AC-3) or MPEG audio decoder.
ÁOtherwise any attempt to play DVDs may cause to
such a high level of noise that it may be harmful to
your ears and damage your speakers.
ÁVideo CDs and CDs can be played as they would nor-
mally be played.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of
Dolby Laboratories. Confidential Unpublished Works.
j 19921997 Dolby Laboratories, Inc. All rights re-
served.
12
Connection
Connecting to an AV amplifier which does not contain Dolby Digital (AC-3)/MPEG
audio decoder
This DVD/VIDEO CD/CD player contains a Dolby Digital (AC-3)/MPEG audio decoder. This enables the playback of DVDs recorded
in Dolby Digital Surround, MPEG audio or Linear PCM without the need for an optional decoder with Dolby Digital, MPEG audio or
Linear PCM processing. When the DVD player is connected to an AV amplifier with 5.1ch input connectors, you can enjoy theater-
quality audio right in your home when playing discs recorded in Dolby Digital Surround, MPEG audio or Linear PCM.
Notes:
ÁAfter connection is made, set the Speaker setting (such as
Yes/No and Large/Small) according to your speaker sys-
tem. (See page 39.)
ÁIf the surround speakers or the center speaker cant be in-
stalled at an equal distance to (or further away from) the
front speakers from the listening position, then change the
delay time setting at the Speaker setting on page 39, to
compensate.
ÁIf the surround speakers are set to None at the Speaker
setting (see page 39), the discs recorded in MPEG 2 audio
or Linear PCM will be played back only in 2 channels even
when the center speaker is connected as well as the front
speakers.
ÁDVDs recorded in Linear PCM/96 kHz sampling in which
Center Speaker is contained will also be played back only
in 2ch.
PCM/U DIGITAL
MPEG
COAXIAL
DIGITAL
OPTICAL
L
AUDIO OUT VIDEO OUT
SUBWOOFER
CENTER SURROUND
6CH DISCRETE
MIXED 2CH
VIDEO
MAIN
AC IN
S VIDEO
L
R R
R
L
2
1
SURROUND
MAIN
VIDEO SIGNAL
AUDIO SIGNAL
DVD/LD
CENTER
6CH DISCRETE INPUT DVD/LD
SUB
WOOFER
L
R
L
R
TV set (optional)
AV amplifier without
Dolby Digital (AC-3)/
MPEG audio decoder
(optional)
Audio cord
(optional)
Video/audio cord (supplied)
DVD/VIDEO CD/CD player
13
A
B
30˚ 30˚
7m
7
8
7
8
Remote control preparation
Battery installation )
Insert the batteries while observing the correct (o) and (p)
polarities as illustrated at right.
Service life of batteries
ÁThe batteries normally last for about one year although this
depends on how often and for what operations the remote
control is used.
ÁIf the remote control unit fails to work even when it is oper-
ated near the player, replace the batteries.
ÁUse size AA (R6P) batteries.
Remote control operation range *
Point the remote control unit no more than about 7 m from the
remote control sensor and within about 60u of the front of the
unit.
ÁThe operating distance may vary according to the bright-
ness of the room.
Notes:
ÁDo not point bright lights at the remote control sensor.
ÁDo not place objects between the remote control unit and
the remote control sensor.
ÁDo not use this remote control unit while simultaneously op-
erating the remote control unit of any other equipment.
Remote control signal sensor
Notes:
ÁDo not use rechargeable (Ni-Cd) batteries.
ÁDo not attempt to recharge, short-circuit, disassem-
ble, heat or throw the batteries into the fire.
ÁDo not drop, step on or otherwise impact the remote
control unit. This may damage the parts or lead to
malfunction.
ÁDo not mix old and new batteries.
ÁIf the remote control unit is not going to be used for a
long time, remove the batteries. Otherwise, electrolyte
may leak which may lead not only to malfunctioning
but also to burns if contact is made with the electro-
lyte.
ÁWipe away any electrolyte leaking inside the remote
control unit, and install new batteries.
ÁIf any electrolyte should come into contact with parts
of your body, wash it off thoroughly with water.
14
f OPEN/CLOSE
/ CD
STOP STILL/PAUSE PLAY
:
SKIP
;
D I G I T A L
2 4
3
f OPEN/CLOSE
PLAY
12
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP
I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
1
2
4
D
PLAY
OPEN/CLOSE
Before enjoying DVD/Video CD/CD
The On-Screen menu language of your player has
been factory pre-set to English.
If you would like to change the menu language to
French, Spanish, German or Italian (for Continental Eu-
rope, United Kingdom and Australia models) or to
French or Spanish (for other models), please refer to
Selecting language of On-Screen Display menu on
page 34.
In the explanations given below it is assumed that En-
glish has been selected as the menu language.
Basic play
Preparations
ÁSwitch the TV ON and select the Audio/Video (AV) position,
e.g. AV1, AV2, which has been connected to the player.
ÁSwitch on the stereo systems power if the player has been
connected to a stereo system.
Basic play
1
Press POWER to switch on the power.
2
Press OPEN/CLOSE to
open the disc tray.
3
Place a disc onto the disc tray.
Hold the disc without touching either of its surfaces, posi-
tion it with the printed title side facing up, align it with the
guides, and place it in its proper position.
e 8 cm disc
f 12 cm disc
4
Press PLAY.
The disc tray is automatically closed and play begins.
ÁWhen the disc tray is closed by pressing OPEN/CLOSE,
press PLAY to commence play.
ÁWhen a menu screen appears on the TV monitor
In case of interactive DVDs or Video CDs with playback
control, a menu screen appears on the TV monitor. Perform
step 5 on page 15 to commence play.
(Example of DVD)
Open
CloseReading
TITLE MENU
Dogs
BirdsLovers
Castles
15
f OPEN/CLOSE
/ CD
STOP STILL/PAUSE PLAY
:
SKIP
;
D I G I T A L
:
SKIP
;
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
5
5
POWER
*/ I
H
SKIP I
TITLE
RETURN
MENU
Basic play
5
Press C/D/A/B and press SELECT, or
press the numeric button(s), to select the
preferred item.
ÁC/D/A/B are not effective for selecting items for
Video CDs.
Play of the selected item now begins.
When the menu continues onto another screen
After step 4 on page 14, press SKIP I. (SKIP buttons may
not be effective depending on the disc.)
ÁTo return to the previous menu screen
Press H SKIP.
ÁFor operation, refer also to the jacket of the disc concerned.
Stopping play and returning to the menu
screen
ÁDVD
Press TITLE, MENU or RETURN.
(Which button is pressed differs depending on the disc
used.)
ÁVideo CD
Press RETURN.
ÁPlay is suspended, and the menu screen is displayed.
After operation
When the unit is not in use, remove the disc and press
POWER to switch the power to the standby mode.
The power will automatically be switched to the standby
mode after 30 minutes or so have elapsed in the stop mode.
(Auto turn-off function)
What is playback control?
If a Video CD has playback control written on its disc
or jacket, it means that particular scenes or information
can be selected for viewing interactively with the TV
monitor using the menu screen.
of the world
TITLE MENU
Birds
Birds
Dogs
Lovers
Castles
1 EAST ASIA
2 SOUTH ASIA
3 MIDDLE EAST
4 AFRICA
5 EUROPE
6 OCEANIA
7 NORTH AMERICA
8
CENTRAL AMERICA
9 SOUTH AMERICA
10 ANTARCTIC
:
SKIP
;
H
SKIP
I
16
f OPEN/CLOSE
/ CD
STOP STILL/PAUSE PLAY
:
SKIP
;
D I G I T A L
:
SKIP
;
PLAY
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
D
PLAY
@
STOP
H
SKIP I
STOP
Basic play
Note:
ÁThe disc continues to rotate while the menu is displayed
even after the player has finished playing a particular item.
When no further selections are to be played, be sure to
press the STOP button to clear the menu display.
ÁIf the disc is placed in upside down (and it is a single sided
disc), the DVD display will indicate NO DISC.
For Continental Europe, United Kingdom and Australia
models
ÁWhen the NTSC DVD/Video CD is played, the playback pic-
ture may roll up or down on some TVs; adjust this using the
V-HOLD control on the TV. TVs not equipped with a V-
HOLD control cannot correct this condition. The playback
picture may shrink vertically and black bars may appear
both on the top and bottom of the screen, or the picture may
be in black and white. This does not indicate a malfunction.
For your reference:
ÁWhen —— appears while a button is being operated, it
means that the corresponding operation is prohibited by the
player or the disc.
Stopping play
Press STOP.
For your convenience:
ÁWhen play is stopped, the unit records the point where
STOP was pressed (RESUME function). (D flashes on
the units display when this function is activated.) Press
PLAY again, and play will resume from this point. When the
tray is opened or STOP is pressed again, the RESUME
function will be cleared.
The RESUME function works only with discs for which the
elapsed playing time appears on the units display during
playback.
This feature will not be cleared when the power is switched
to the standby mode and then returned to ON.
Skipping ahead or back
[Skipping\ahead]
Press SKIP I during play.
A chapter (DVD) or a track (Video CD/CD) is skipped each
time the button is pressed.
[Skipping\back]
Press H SKIP during play.
When the button is pressed once midway through a chapter/
track, play returns to the start of that chapter/track. When it is
pressed again, a chapter/track is skipped each time the but-
ton is pressed.
For your reference:
ÁWhen H SKIP I is pressed during menu play of Video
CDs, a menu screen may sometimes be recalled.
17
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
g
STILL/PAUSE
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
D
PLAY
F
G
SLOW/
SEARCH
Rapid advance (Rapid reverse)
Press SLOW/SEARCH F or G during
play.
ÁThe speed of advance (reverse) is relatively slow at first.
When the button is pressed again, the speed becomes fast-
er. (Each time the button is pressed, the speed increases
up to 5 steps.)
To return to normal play
Press PLAY.
For your reference:
ÁWhen SLOW/SEARCH is used during menu play of Video
CDs, a menu screen may sometimes be recalled.
Still picture (Pause)
Press STILL/PAUSE during play.
ÁDVD/Video CD:
The player will be placed in the still
picture mode.
ÁCD:
The player will be placed in the
pause mode.
To return to normal play
Press PLAY.
Frame advance [DVD/Video CD]
Press STILL/PAUSE in the still picture mode.
The disc is advanced by one frame each time the button is
pressed.
To return to normal play
Press PLAY.
Note:
ÁWhether the pictures are advanced by a frame or field is
selected automatically. (See page 41.)
F
G
SLOW/
SEARCH
Reverse
direction
Forward
direction
(Example)
[DVD/Video CD]
Still
18
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP
I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
@
STOP
D
PLAY
MENU
F
G
SLOW/
SEARCH
Slow-motion play [DVD/Video CD]
Press SLOW/SEARCH F or G in the still
picture mode.
(See page 17.)
ÁThe speed of slow-motion is slow at first. When the button is
pressed again, the speed becomes faster. (Each time the
button is pressed, the speed increases up to 5 steps.)
To return to normal play
Press PLAY.
For your reference:
ÁFor Video CDs, slow-motion playback in reverse direction is
not possible.
Enjoying Video CDs with
playback control without using
menus [Video CD only]
1. Press STOP after the menu screen appears (after step 4
on page 14).
(PBC will be cleared from the units display.)
2. Press the numeric button(s) to select the preferred track.
(Play begins.)
ÁRefer to the jacket etc. of the disc concerned for the
track numbers.
ÁPress 1 to start play from the beginning of the disc.
To return to menu play
Press STOP to stop playback and press MENU.
(PBC will light up on the units display and the menu screen
is resumed.)
Perform step 5 on page 15.
Reverse
direction
Forward
direction
F
G
SLOW/
SEARCH
(Example)
19
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
A
B
C
D
35 1:07:48 3
LPCM
FRA
196k 24
b
T
1 2 3 4 5
2
ENG
ON
2
2
AB
AB
2
AB
7:48
L R
OFF
PBC
T PRG
1 2 3 4 5
7:48
1 2 3 4 5
T PRG
2
3
3
2
SELECT
RETURN
ON SCREEN
1
CLEAR
General information about GUI
screens
This unit features GUI (Graphical User Interface) screens
consisting of icons showing disc information (title/chapter/
track number, elapsed playing time, audio/subtitle language,
and angle) and player information (repeat play, play mode,
marker, Karaoke vocal ON/OFF, etc.).
Some icons only show the indicated information. Other icons
allow the settings to be changed.
Common procedures )
1
Press ON SCREEN during play or in the
stop mode.
Each time this button is pressed, the TV monitor chang-
es as shown below.
[>GUI screen for selecting disc information
l
v
l>GUI screen for selecting player information
l
v
l>GUI screen for slow-motion play and rapid advance
l>(reverse)
l
v
{=GUI screen is cleared
ÁSome functions cannot be accessed from the stop
mode.
2
Press C/D to select the preferred item.
ÁThe currently selected item is indicated by the yellow
frame on the GUI screen.
3
Press A/B to select the preferred setting.
ÁWhen numbers are displayed (e.g. title No.), the numer-
ic buttons are also effective for setting instead of A/B.
ÁFor some functions, the setting will be registered imme-
diately; for others, SELECT must be pressed.
Press ON SCREEN, RETURN or CLEAR to clear the GUI
screen.
Example of GUI screens
(The screens may differ depending on the disc contents.)
ÁDVD (*)
ÁVideo CD (+)
ÁCD (,)
For your reference:
ÁDepending on the type of DVD software and a TV with auto-
matic picture zoom function enabled, the GUI screen may
not be displayed or only partially displayed on the TV
screen.
In this case, select the appropriate TV screen type by con-
sulting the operation manual of the TV.
20
2
OFF
PBC
s
1
35
3
LPCM
FRA
96k 24
b
3
LPCM
FRA
96k 24
b
3
LPCM
FRA
96k 24
b
3
LPCM
FRA
96k 24
b
3
LPCM
FRA
96k 24
b
1:07:48
1
L R
2
3
4
5
6
7
8
0
o
p
q
r
2
ENG
ON
2
ENG
ON
2
ENG
ON
1
U
Vocal
ON
9
Detailed descriptions of each GUI
icon
Screen for disc information
ÁA B means pressing A/B and Numeric means pressing the nu-
meric button.
\1
The track number cannot be selected during menu play of the Video
CD.
\2
This function does not work with some DVDs.
Remarks
To show the current title No. [DVD] or
track No. [Video CD/CD] and to jump to
the desired title No. or track No.
\1
To show the current chapter No. or to
jump to the desired chapter No.
[DVD only]
To show the elapsed time and to directly
select scenes by the elapsed time
\2
[DVD] or to show the elapsed time
[Video CD/CD]
To show the current audio soundtrack
language No. and to change to the
desired one [DVD only] (See page 28.)
To show the audio soundtrack language
selected using the above icon [DVD only]
To show the audio attribute (type) of the
disc currently being played
[DVD only]
ÁLPCM (Linear PCM), MPEG (MPEG audio) or
$ [Dolby Digital (AC-3)]
To show the audio attribute (sampling
frequency or channel No.) of the disc
currently being played
[DVD only]
ÁFor Linear PCM disc: 48 kHz or 96 kHz
ÁFor Dolby Digital (AC-3) disc: 1ch to 5.1ch
ÁFor MPEG audio disc: 1ch to 5.1ch
To show the audio attribute (bit No.) of
the disc currently being played
[DVD only]
ÁFor Linear PCM disc: 16 bit to 24 bit
To show the number of recorded vocals
[DVD Karaoke only] (See page 28.)
Á1 vocal: ON or “––” (OFF)
Á2 vocals: V1oV2, V1, V2 or “––” (OFF)
To show the current subtitles language
No. and to change to the desired one
[DVD only] (See page 27.)
To show the subtitle language selected
using the above icon [DVD only]
To display/clear subtitles [DVD only]
(See page 27.)
To show the current angle No. and to
change to the desired one
[DVD only]
(See page 29.)
To select the audio mode
[Video CD only] (See page 28.)
ÁLR, L or R
To show whether Video CD menu play is
ON or OFF
[Video CD with playback control
only] (See pages 14, 15 and 18.)
Changing
method
A B or
Numeric/
SELECT
A B or
Numeric/
SELECT
Numeric/
SELECT
A B or
Numeric
——
——
——
——
——
A B or
Numeric
——
A B
A B or
Numeric
A B
——
No.
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
21
A
C
B
2
4
1 2
4
3
AB
T
PRG
1 2 3 4 5
1
2
3
4
Detailed descriptions of each GUI icon
For your reference:
ÁFor the language abbreviations used for the audio sound-
track and subtitle language icons, see the table ).
ÁC D AB means pressing C/D/A/B.
\1
This function does not work with an interactive DVD or dur-
\1
ing menu play of Video CD.
Screen for slow-motion play and rapid
advance (reverse) +
e Still/Pause
Press A to select O.
f Slow-motion play
Press C/D.
\
M: Backward [DVD only]
L: Forward [DVD/Video CD only]
g Play
Press B to select D.
h Rapid reverse/advance
Press C (Backward)/D (Forward).
\
\
Each time the button is pressed, the speed increases in up
to 5 steps.
Screen for player information *
No.
\1
e
\1
f
g
\1
h
Remarks
To start A-B repeat play (See page 25.)
To select the repeat play mode
(See page 24.)
ÁC (chapter repeat), T (title repeat) or
ÁOFF (normal play) [DVD]
ÁT (track repeat), A (disc repeat) or
ÁOFF (normal play) [Video CD/CD]
To show the current play mode
[Video CD/CD only]
(See pages 22 and 23.)
Á“––” (normal play), PRG (program
Áplay) or RND (random play)
To store a marker
To recall a marker
To clear a marker
(See page 26.)
Changing
method
SELECT
A B
——
SELECT
C D>A
C D
>CLEAR
ENG English FRA French DEU German
ITA Italian ESP Spanish NLD Dutch
SVE Swedish NOR Norwegian DAN Danish
POR Portuguese RUS Russian JPN Japanese
CHI Chinese KOR Korean MAL Malay
VIE Vietnamese THA Thai U Others
22
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
2
1
3
2
Program play [Video CD/CD]
The player plays the tracks in the disc in an order you
specify.
1
Press PLAY MODE in the stop mode.
The program playback screen appears on the TV mon-
itor.
2
Press C/D/A/B and press SELECT, or
press the numeric button(s), to select the
preferred track number.
The selected track is stored in the memory.
ÁRepeat step 2 to select another track.
ÁUp to 18 tracks can be programmed.
3
Press PLAY.
Play now begins in the programmed sequence.
After playback
Play is stopped and the program playback screen is dis-
played.
Track numbers
included in the
disc
Choose a track, then press SELECT
Clear last
Clear all
Press PLAY to start
11319
21420
315
7
8
9
41610
51711
61218
21
Clear last
Clear all
Press PLAY to start
11319 2
21420
315
7
8
9
41610
51711
61218
21
Choose a track, then press SELECT
Clear last
Clear all
Press PLAY to start
11319 2
2
14 20
3315
7
88
9
41610
5
5
61711
61218
21
Choose a track, then press SELECT
23
Program play [Video CD/CD]
Returning to normal play
)
1. Press STOP. (Program play is suspended.)
2. Press PLAY MODE twice.
3. Press PLAY.
Normal play begins.
(The content of the program is still retained in the memory.)
Clearing the program )
When the program playback screen is displayed
ÁTo clear the last program one by one
Move to Clear last and press SELECT.
(Pressing CLEAR of the remote control unit also clears the
last program.)
ÁTo clear all the programs
Move to Clear all and press SELECT.
(The programs are also cleared when the power is switched
to the standby mode or the disc is removed.)
Random play [Video CD/CD] *
The player plays the tracks in the disc in random order.
1
Press PLAY MODE twice in the stop mode.
The random playback screen appears on the TV monitor.
2
Press PLAY.
Play now begins in the random order.
After playback
Play is stopped and the random playback screen is dis-
played.
Returning to normal play
1. Press STOP. (Random play is suspended.)
2. Press PLAY MODE.
3. Press PLAY.
Normal play begins.
Clear last
Clear all
Press PLAY to start
11319 2
2
14 20
3315
7
88
9
41610
5
5
61711
61218
21
Choose a track, then press SELECT
Random Playback
Press PLAY to start
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP
I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP
I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
B
2
1
A
@
STOP
PLAY MODE
CLEAR
D
PLAY
SELECT
@
STOP
D
PLAY
PLAY MODE
24
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
REPEAT
Repeat play
Repeat viewing (listening)
Press REPEAT during play.
Each time this button is pressed, the TV monitor changes as
shown below and the disc will repeat a chapter or title (DVD)
or a track (Video CD/CD).
ÁDVD
Repeat of chapter being played
Repeat of title being played
Cancel repeat mode
(Normal play)
ÁVideo CD/CD
Repeat of track being played
Repeat of entire disc contents
Cancel repeat mode
(Normal play)
To return to normal play
Press REPEAT several times until “OFF” is displayed.
Note:
ÁRepeat play works only with discs for which the elapsed
playing time appears on the unit’s display during playback.
ÁRepeat play may not work correctly with some DVDs.
C
T
OFF
T
A
OFF
25
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
A
B
1
·
2
A-B
REPEAT
Repeat play
To enjoy program repeat play
)
If REPEAT is pressed during program play (see pages 22
and 23), the display changes as follows:
Repeat of programmed track
being played
Repeat of all programs
Cancel repeat mode
(Normal program play)
Repeating sections between two
specific points (A-B repeat) *
1
Press A-B during play at the point where
repeat play is to commence (A).
2
Press A-B at the point where repeat play is
to be concluded (B).
Repeat play of the selection between points A and B starts.
To return to normal play
Press A-B several times until Á Á is displayed.
Note:
ÁA-B repeat play works only within a title [DVD] or a track
[Video CD/CD].
ÁA-B repeat play works only with discs for which the elapsed
playing time appears on the units display during playback.
ÁSome subtitles recorded around point A or B may fail to ap-
pear. [DVD]
T PRG
A
OFF
PRG
PRG
A
A B
26
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
A
B
3
2
2
1
1
2
3
SELECT
MARKER
MARKER
Storing markers in memory to be
viewed (listened) again
Storing a marker in the memory )
1
Press MARKER during play.
2
Press SELECT during play at the starting
point to be viewed (listened) again.
Up to 5 markers can be stored in the memory.
ÁTo store markers 2 to 5, press +/, to move to 7 and
press SELECT.
ÁPress MARKER to clear the display.
Recalling/clearing a marker *
1
Press MARKER during
play.
2
Press +/, to select the marker to be re-
called/cleared.
3
Press ) to recall a marker.
or
Press CLEAR to clear a marker.
Play resumes from the point corresponding to the selected
marker. (The display will be cleared automatically.)
or
The selected marker is cleared. (Press MARKER to clear the
display.)
Note:
ÁThese operations work only with discs for which the elapsed
playing time appears on the units display during playback.
ÁSome subtitles recorded around the marker may fail to ap-
pear. [DVD]
For your reference:
ÁAll the markers are cleared when the unit is switched to the
standby mode or the disc tray is opened.
7 indicates no marker has
been stored yet.
Indicates MARKER 1 is stored
in the memory.
(If SELECT is pressed where
any number is already displayed,
the previous starting point will be
replaced by the new one.)
U U U U U
1
U U U U
1 2 3 4
U
1 2 3 4
U
27
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
2
1
2
2
SUBTITLE
SELECT
Changing subtitle language
[DVD only]
It is possible to change the subtitle language from the one se-
lected at the initial settings to a different language, if avail-
able. (See page 32.)
(This operation works only with discs on which multiple subti-
tle languages are recorded.)
1
Press SUBTITLE during play.
ÁWhen no subtitles are recorded, “–” will be displayed in-
stead of the language number.
2
Press )/* until the preferred language is
selected.
Pressing the numeric
button(s) also changes
the subtitle language.
ÁPress SUBTITLE or SELECT to clear the display.
To clear/display the subtitles
Press +/, to select ON or OFF at the step 2.
Note:
ÁIn some cases, the subtitle language is not changed imme-
diately to the selected one.
For your reference:
ÁWhen the preferred language is not selected even after
pressing the button several times, it means that the lan-
guage is not available on the disc.
ÁWhen the unit is switched to the standby mode or the disc
tray is opened, subtitles appear in the language selected at
the initial settings. If this language is not recorded on the
disc, they appear in the discs priority language.
Number of the subtitle
language being played
back
I love you
2
ENG
ON
Je t'aime
1
FRA
ON
28
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
A
B
2
1
2
2
2
1
2
SELECT
AUDIO
SELECT
AUDIO
Changing audio soundtrack
language [DVD only] )
It is possible to change the audio soundtrack language from
the one selected at the initial settings to a different language,
if available. (See page 32.)
(This operation works only with discs on which multiple audio
soundtrack languages are recorded.)
1
Press AUDIO during play.
ÁWhen no audio soundtrack is recorded, “–” will be dis-
played instead of the language number.
2
Press )/* until the preferred language is
selected.
Pressing the numeric
button(s) also changes
the audio soundtrack
language.
ÁPress AUDIO or SELECT to clear the display.
For your reference:
ÁWhen the preferred language is not selected even after
pressing the button several times, it means that language is
not available on the disc.
ÁWhen the unit is switched to the standby mode or the disc
tray is opened, the language heard is the one selected at
the initial settings. If this language is not recorded on the
disc, only the available language on the disc will be heard.
Switching vocals ON or OFF for
Karaoke discs [DVD/Video CD] *
1
Press AUDIO during play.
2
Press +/, until the preferred setting is se-
lected.
ÁDVD Karaoke (1 vocal)
ON()––– (OFF)
ÁDVD Karaoke (2 vocals)
1o2>V1>V2>––– (OFF)
^------------------------------------------}
ÁVideo CD
LR>L>R
^-------------}
ÁPress AUDIO or SELECT to clear the display.
Note:
ÁThis operation does not work with CDs.
Number of the audio
soundtrack language
being played back
Hello
1
LPCM
ENG
96k 24
b
Bon
jour
3
LPCM
FRA
96k 24
b
1
U
Vocal
ON
1
U
Vocal
---
L R
29
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
2
2
1
2
SELECT
ANGLE
Viewing from another angle
[DVD only]
Some DVDs may contain scenes which have been shot si-
multaneously from a number of different angles. For these
discs, the same scene can be viewed from each of these dif-
ferent angles using the ANGLE button. (The recorded angles
differ depending on the disc used.)
1
Press ANGLE during play.
2
Press )/* until the preferred angle is se-
lected.
Pressing the numeric
button(s) also changes
the angle.
ÁPress ANGLE or SELECT to clear the display.
Note:
ÁThis function only works for discs having scenes recorded
at different angles.
ÁANGLE lights up on the FL display at scenes recorded at
different angles to indicate that angle switching is possible.
The angle number can be programmed beforehand; the
angle will be switched to the selected number when
“ANGLE” lights up.
Number of angle being
played back
1
5
30
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
A
B
2
1
2
2
2
1
2
TITLE
MENU
Using a title menu [DVD only] )
Some discs with movies, for example, may be available with
two or more titles. If the disc has a title menu recorded on it,
the TITLE button can be used to select the movie title.
(The details of operation differ depending on the disc used.)
1
Press TITLE during play.
A list of the titles on the disc is
now displayed.
(Example)
ÁPressing TITLE again resumes play from the scene
when TITLE was first pressed.
2
Press +/,/)/* and press SELECT or
PLAY, or press the numeric button(s), to
select the preferred title.
The selected title now starts playing.
Using a DVD menu [DVD only] *
Some DVDs have unique menu structures called DVD
menus. For example, DVDs programmed with complex con-
tents provide guide menus, and those recorded with various
languages provide menus for audio and subtitle language. Al-
though the DVD menus contents and operation differ from
disc to disc, the following explains basic operation when this
feature is used.
1
Press MENU during play.
The DVD menu available on the
disc is now displayed.
(Example)
ÁPressing MENU again resumes play from the scene
when MENU was first pressed.
2
Press +/,/)/* and press SELECT, or
press the numeric button(s), to select the
preferred item.
The selected item is now executed.
When the menu continues onto another screen
Repeat step 2.
TITLE MENU
Dogs
Lovers
Castles
Birds
TITLE MENU
Dogs
Lovers
Castles
Birds
Birds
of the world
DVD MENU
1.SUBTITLE
2.AUDIO
3.ANGLE
DVD MENU
1.SUBTITLE
2.AUDIO
3.ANGLE
31
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
1
2
·
3
RETURN
SELECT
SET UP
Initial settings
Once the intial settings have been completed, the player can
always be operated under the same conditions (especially
with DVD discs).
The settings will be retained in the memory even after switch-
ing the power to the standby mode until the settings are
changed.
Common procedures of initial settings
1
Press SET UP in the stop mode.
2
Press )/* to select the preferred item and
SELECT.
Each screen for setting the value is displayed.
1 Disc Languages (see page 32)
2 Ratings (see page 33)
3 Menu Language (see page 34)
4 On-Screen Messages (see page 35)
5 FL Display (see page 35)
6 TV Aspect (see page 36)
7 Digital Audio Output (see page 37)
8 Speaker setting (see page 39)
9 Other Settings (see page 41)
3
Press )/* to select the preferred value
and press SELECT.
ÁSome items require additional steps. (See the respec-
tive page.)
Setting is finished and the initial settings screen is displayed.
To cancel during setup operation
Press RETURN or select “0”. (The previous screen is dis-
played.)
To clear the initial settings screen
Press * to select “0” and press SELECT. (Pressing SET UP
or RETURN also clears the initial settings screen.)
For your reference:
ÁThe numeric buttons can also be used for selecting items or
values instead of )/*; in this case, pressing SELECT is
not necessary.
0 Exit
1 Disc Languages
2 Ratings
3 Menu Language
4 On-Screen Messages
5 FL Display
6 TV Aspect
Level 8
English
On
Bright
4:3
7 Digital Audio Output
8 Speaker Setting
9 Other Settings
32
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
1
3
2
~
SELECT
CLEAR
Initial settings
Selecting disc languages [DVD only]
This is to select the audio soundtrack language, subtitle lan-
guage and the language used in title menus or DVD menus
which will always be used for every disc to be played back.
1
At the initial settings screen
Press )/* to select 1 Disc Languages
and press SELECT.
2
Press )/* to select the preferred item
(13) and press SELECT.
When 1 Audio is selected
English: English is selected (Factory setting)
French/German/Italian/Spanish:
\
Each language is selected.
Original: The original language of each disc will be
selected.
Other 7777: Another language can be selected.
(Refer to the language codes on
page 43. Press CLEAR if an incorrect
language code is entered.)
When 2 Subtitle is selected
Automatic: The same language selected for the Au-
dio will be selected. (Factory setting)
ÁIf the language selected for the Audio is
actually used during playback, the subti-
tles will not appear.
ÁIf another language is used during play-
back, the subtitles will appear in the lan-
guage selected at the setup Audio”.
English/French/German/Italian/Spanish:
\
Each language is selected.
Other 7777: Another language can be selected.
When 3 Menus is selected
English: English is selected (Factory setting)
French/German/Italian/Spanish:
\
Each language is selected.
Other 7777: Another language can be selected.
\
German and Italian can be selected only in Continental
Europe, United Kingdom and Australia models.
3
Press )/* to select the preferred language
at each screen and press SELECT.
The screen at the step 1 is displayed. Press * to select “0”
and press SELECT to return to the initial settings screen.
Note:
ÁIf the language selected is not available on the disc, the lan-
guage designated by each disc will be selected.
Also refer to Common procedures of initial settings on
page 31.
Disc Languages
1 Audio
2 Subtitle
3 Menus
0 Exit
English
English
Automatic
33
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
3
1
4
~
Initial settings
Selecting rating level [DVD only]
This is to disable the playing of specified DVDs which are un-
suitable for children.
ÁSome DVDs are encoded with specific rating level. If the
rating level of the disc is higher than that preset in the setup
operation, playback of the disc will be prohibited.
1
At the initial settings screen
Press )/* to select 2 Ratings and press
SELECT.
All DVDs can be
played back.
(Factory setting)
DVDs for general
audiences/children
can be played back.
(DVDs for adults are
prohibited.)
2
Press )/* to select the preferred level and
press SELECT.
3
When level 7 or lower is selected
Input a 4-digit password and press
SELECT.
The lock symbol
appears closed to
show the rating is
locked.
Example: 4343
Do not forget your
password.
4
Press SELECT.
Setting is finished and the initial settings screen is displayed.
ÁThe rating is locked. Any discs whose rating is higher than
the setting cannot be played back unless the correct pass-
word is entered.
Also refer to Common procedures of initial settings on
page 31.
(Continued on the next page)
Playback of all DVDs is
prohibited. (e.g. to
prohibit playback of
DVDs for adults which
are not encoded with
rating level information)
DVDs for children can be
played back. (DVDs for adults/
general audiences are
prohibited.)
Please set a rating limit
8 No Limit
7
6
5
4
3
2
1
0 Lock All
Press RETURN to cancel
Ratings
Enter a 4-digit password,
then press SELECT
Press RETURN to cancel
U U U U
The player is locked.
Remember the password.
Press SELECT to continue
4343
Ratings
34
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
A
B
SELECT
1
·
2
Initial settings
To change the settings
)
1. Press )/* to select “2”
at the initial settings
screen and press
SELECT.
2. Input a 4-digit password
and press SELECT.
3. Press )/* to select the preferred item (14) and press SELECT.
ÁPress * to select “0” and press SELECT to exit.
(Setting is finished and the initial settings screen is displayed.)
4.
When 1 Unlock Player is selected
Press SELECT.
When 2 Change Password is selected
Enter a new 4-digit password and press SELECT. Press SELECT
again.
When 3 Change Level is selected
Select a level and press SELECT.
When 4 Temporary Unlock is selected
(The rating is unlocked temporarily only for the current
disc.)
Press SELECT.
Setting is finished and the initial settings screen is displayed.
Note:
ÁSome discs may not be encoded with specific rating level informa-
tion though its disc jacket says that it is for adults”.
For those discs, the age restriction will not work.
Selecting language of On-Screen
Display menu *
1
At the initial settings screen
Press )/* to select 3 Menu Language
and press
SELECT.
2
Press )/* to select the preferred language
and press SELECT.
\
German and Italian can be selected only in Continental Europe,
United Kingdom and Australia models.
Setting is finished and the initial settings screen is displayed.
Also refer to Common procedures of initial settings on page
31.
Factory settings
Press RETURN to cancel
Ratings
Enter your 4-digit password,
then press SELECT.
U U U U
0 Exit
Ratings
1 Unlock Player
2 Change Password
3 Change Level
4 Temporary Unlock
Select the language
for these Menus.
1 English
2 Français
3 Deutsch
4 Italiano
5 Español
Press RETURN to cancel
35
A
B
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP
I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
1
·
2
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP
I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
1
·
2
Initial settings
Switching the On-Screen Display
ON or OFF )
You can select whether On-Screen Display messages such
as PLAY and STOP will be displayed or not.
1
At the initial settings screen
Press )/* to select 4 On-Screen Messag-
es and press SELECT.
2
Press )/* to select the preferred item
(1 or 2) and press SELECT.
Setting is finished and the initial settings screen is displayed.
Selecting the display brightness *
1
At the initial settings screen
Press )/* to select 5 FL Display and
press SELECT.
2
Press )/* to select the preferred item
(13) and press SELECT.
Setting is finished and the initial settings screen is displayed.
For your reference:
ÁEven if 3 Dim During DVD/VCD Play (Auto) is selected,
the display resumes brightness when a button for special
play such as SLOW/SEARCH and STILL/PAUSE is
pressed.
Also refer to Common procedures of initial settings on
page 31.
Factory setting
Factory setting
On-Screen Messages
1 On
2 Off
Press RETURN to cancel
FL Display
1 Bright
2 Dim
3
Dim During DVD/VCD Play(Auto)
Press RETURN to cancel
36
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
1
·
2
Initial settings
Selecting TV screen type
Select the appropriate screen type according to your TV set;
conventional size screen (4:3) or wide-screen (16:9).
1
At the initial settings screen
Press )/* to select 6 TV Aspect and
press SELECT.
2
Press )/* to select the preferred item
(1 or 2) and press SELECT.
4:3 Select when a conventional TV set is con-
nected. (factory setting)
The video material
formatted in the
Pan & Scan style is
played back in that style
(the left and right edges
are cut off).
The video material not
formatted in the Pan &
Scan style is played
back in the letterbox
style (black bands
appear at top and
bottom of screen).
16:9 Select when a wide-screen TV set is con-
nected.
Played in FULL
size. (Setting the
wide-screen TV to
FULL mode is also
necessary.)
\ Each screen shows an example when the video mate-
rial for a wide-screen is played.
(This setting does not affect the video material for
conventional size.)
Setting is finished and the initial settings screen is displayed.
Also refer to Common procedures of initial settings on
page 31.
Select your TV aspect
1 4:3
2 16:9
Press RETURN to cancel
37
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
1
3
~
SELECT
Initial settings
Selecting digital output
Select the digital output to be output from the optical/coaxial
digital audio output connector of the unit.
1
At the initial settings screen
Press )/* to select 7 Digital Audio Out-
put and press SELECT.
2
Press )/* to select the preferred item
(13) and press SELECT.
When 1 LPCM (DVD) is selected
Off: Only linear PCM of 48 kHz/16 bit is output from
the digital audio output connector. During play-
back of the DVD recorded in the linear PCM of
48 kHz/20 bit/24 bit or 96 kHz, no digital audio is
output. (Factory setting)
PCM: During playback of the DVD recorded in the linear
PCM of 48 kHz/20 bit/24 bit or 96 kHz, digital au-
dio converted to 48 kHz/16 bit is output.
(Digital output of PCM audio is restricted to
48 kHz/16 bit or below for copyright protection.)
When 2 Dolby Digital is selected
Bitstream: Dolby Digital (AC-3) bitstream (2ch5.1ch)
is output. (Factory setting)
PCM: PCM (2ch) of 48 kHz/16 bit is output.
When 3 MPEG is selected
PCM: PCM of 16 bit is output. (Factory setting)
Bitstream: Bitstream is output.
3
Press )/* to select the preferred value at
each screen and press SELECT.
The screen at the step 1 is displayed. Press * to select “0”
and press SELECT to return to the initial settings screen.
Also refer to Common procedures of initial settings on
page 31.
(Continued on the next page)
Digital Audio Output
1
LPCM (DVD)
2
Dolby Digital
3 MPEG
0 Exit
Off
Bitstream
PCM
38
A
Initial settings
For your reference:
ÁMake settings as shown in the table ) depending on the
kind of amplifier that is connected to the optical/coaxial digi-
tal audio output connector.
\
Audio output from the units audio output connectors is con-
verted to 48 kHz/16 bit in addition to audio from the digital
audio output connector.
To enjoy high quality sound at 48 kHz/20 bit/24 bit or
96 kHz, connect the amplifier or decoder directly to the au-
dio output connectors, not to the digital audio output con-
nector. [Select Off at the 1 LPCM (DVD).]
MPEG
PCM
PCM
Bitstream
Dolby Digital
Bitstream
Bitstream
Bitstream
Type of amplifier
to be connected
No amplifier is
connected
AV amplifier
including Dolby
Digital decoder
AV amplifier
including Dolby
Digital/MPEG
audio decoder
Recommendable setting
LPCM
(DVD)
Off
PCM
\
PCM
\
39
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP
I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
POWER
A
B
L
C
R
SW
SL SR
CH.
1
3
~
L
C
Exit
3.9
ms
5.3
ms
-3
dB
+1
dB
+2
dB
+2
dB
Test
R
SW
SL SR
Speaker Setting
Press RETURN to cancel
ÁUnderlined item is a factory setting.
2
Press +/,/)/* to select the preferred
item and press SELECT.
3
Press +/,/)/* to select the preferred val-
ue and press SELECT.
Speaker icons
ÁIf the speaker is connected, display the icon.
ÁClear the icon if the speaker is not connected.
ÁIf the speaker supports low-frequency (under 100 Hz)
reproduction, select the larger icon. If the speaker’s
low-frequency (under 100 Hz) reproduction ability is
poor, select the smaller icon. [When the subwoofer is
not connected, be sure to select Large for the front
speakers (L/R).]
Delay time:
If the surround speakers or the center speaker cant be
installed at an equal distance to (or further away) the
front speakers from the listening position, change the de-
lay time to get better surround effect.
ÁWhen D2 or D3 is equal to or larger than D1, no setting
is necessary (*). Otherwise, change the setting ac-
cording to the table below.
Initial settings
Speaker setting )
1
At the initial settings screen
Press )/* to select 8 Speaker Setting
and press SELECT.
Front (L)
Large/Small
Center
Delay time
Center
Large/Small/
None
Front (R)
Large/Small
Subwoofer
Yes/
No
Surround (L)
Large/Small/
None
Surround (L/R)
Delay time
Surround (R)
Large/Small/
None
Channel balance:
While listening to the test signal, adjust the volume of the
center, surround (L), surround (R) speakers and the sub-
woofer so that the volume is equal to that of the front
speakers.
(Continued on the next page)
Speaker
Center speaker
(D2)
Surround
speakers (D3)
Delay time
1.3 ms
2.6 ms
3.9 ms
5.3 ms
5.3 ms
10.6 ms
15.9 ms
Difference
between D1 and
D2/D3
approx. 150 cm
approx. 100 cm
approx. 150 cm
approx. 200 cm
approx. 200 cm
approx. 400 cm
approx. 600 cm
Center speaker
Front speaker (L)
Front speaker (R)
Subwoofer
Surround speaker (R)Surround speaker (L)
D2
D1
D1
D3D3
40
Initial settings
4
Press +/,/)/* to select Exit and press
SELECT.
Setting is finished and the initial settings screen is displayed.
Note:
ÁThe Large/Small setting has no effect on DVDs recorded
in MPEG 2 audio.
For your reference:
ÁTo output the test signal
1. Press +/,/)/* to select Test, and then press
SELECT.
(Test signals will be output consecutively from each
speaker clockwise.)
2. Press +/,/)/* to select the appropriate volume
(p6 dB through o6 dB) while the test signal is being out-
put from the speaker.
3. Press SELECT. (The test signals are stopped.)
Also refer to Common procedures of initial settings on
page 31.
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
4
SELECT
41
POWER
@
STOP
TITLE
SUBTITLE
MARKER
ANGLEAUDIO
ON SCREEN RETURN
MENU
SELECT
H
SKIP I F
G
D
PLAY
g
STILL/PAUSE
OPEN/CLOSE
*/ I
PLAY MODE
REPEAT
A-B CLEAR
DVD
SET UP
SLOW/
SEARCH
~
1
3
SELECT
Initial settings
Other settings
1
At the initial settings screen
Press )/* to select 9 Other Settings and
press SELECT.
2
Press )/* to select the preferred item
(14) and press SELECT.
When 1 Still Mode is selected
Automatic: Frame still and Field still are automati-
cally selected during the still mode.
(Factory setting)
Field: Select this setting when jittering occurs in
the pictures even when Automatic is se-
lected.
When 2 Audio during Search is selected
On: Factory setting (When noises during search are dis-
On: agreeable, select Off.)
Off: Select this setting if audio during search is not nec-
essary.
When 3 TV Mode (4:3) is selected
Pan & Scan: The video material for a wide-screen will
be played back in the Pan & Scan style
on a conventional size TV.
(Factory setting)
ÁVideo material not formatted in the Pan
& Scan style will be played back in the
letterbox style. (See page 36.)
Letterbox: Select this setting to play back the video
material for a wide-screen in the letterbox
style on a conventional size TV.
When 4 D. (Dynamic) Range Compression is se-
lected
Off: Normal audio range is selected. (Factory setting)
On: Select this setting to enjoy listening to dynamic
sound even on a low volume. This is useful for late-
night listening. [This function only works with Dolby
Digital (AC-3) DVDs.]
3
Press )/* to select the preferred value at
each screen and press SELECT.
The screen at the step 1 is displayed. Press )/* to select
“0” and press SELECT to return to the initial settings screen.
Also refer to Common procedures of initial settings on
page 31.
Other Settings
1 Still Mode
2 Audio during Search
3 TV Mode (4:3)
4 D. Range Compression
0 Exit
Automatic
On
Pan&Scan
Off
42
A
B
C
Disc handling and maintenance
Handling precautions
ÁHold the disc by the edges so the surface will not be soiled
with fingerprints. ())
Fingerprints, dirt and scratches can cause skipping and dis-
tortion.
ÁDo not write on the label side with a ball-point pen or other
writing utensils.
ÁDo not use record cleaning sprays, benzine, thinner, static
electricity prevention liquids or any other solvent.
ÁBe careful not to drop or bend the disc.
ÁDo not install more than 1 disc on the disc tray.
ÁDo not try to close the disc tray when the disc is not in-
stalled properly. (*)
ÁBe sure to store the disc in its exclusive case when not in
use.
If the surface is soiled +
Wipe gently with a soft, damp (water only) cloth.
When wiping discs, always move the cloth from the center
hole toward the outer edge.
(If you wipe the discs using a circular motion, circular scratch-
es are likely to occur, which will cause noise.)
If the disc is brought from a cold to a warm en-
vironment, moisture may form on the disc
Wipe this moisture off with a soft, dry, lint-free cloth before
using the disc.
Improper disc storage
You can damage discs if you store them in the following
places:
ÁAreas exposed to direct sunlight
ÁHumid or dusty areas
ÁAreas directly exposed to a heat outlet or heating appliance
Discs which cannot be played with this player
For Continental Europe and United Kingdom models
ÁDVD with Region No. other than “2” or ALL
For Australia model
ÁDVD with Region No. other than “4” or ALL
For other models
ÁDVD with Region No. other than “3” or ALL
ÁDVD-ROM
ÁDVD-R/DVD-RAM
ÁCD-ROM
ÁCDV
ÁCD-G
ÁDo not try to play Photo CD or CD-R.
To prevent a malfunction of this unit
ÁDo not use any non standard shaped CD (heart etc.) avail-
able on the market, because it may damage the unit.
ÁDo not use a CD with tape, seals, or paste on it, because
damage to the unit may result.
Maintenance
ÁBe sure to switch the power to the standby mode and dis-
connect the AC mains lead before maintaining the unit.
ÁWipe this unit with a dry soft cloth.
If the surfaces are extremely dirty, wipe clean with a cloth
which has been dipped in a weak soap-and-water solution
and wrung out thoroughly, and then wipe again with a dry
cloth.
ÁNever use alcohol, benzine, thinner, cleaning fluid or other
chemicals. And do not use compressed air to remove dust.
Disc tray
Disc
43
Language code list
Enter the appropriate code number for the initial settings Audio, Subtitle and/or Menus (see page 32).
Code
6565
6566
6570
6577
6582
6583
6588
6590
6665
6669
6671
6672
6678
6679
6682
6765
6779
6783
6789
6865
6869
6890
6976
6978
6979
6983
6984
6985
7065
7073
7074
Language Name
Afar
Abkhazian
Afrikaans
Ameharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bengali; Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
German
Bhutani
Greek
English
Esperanto
Spanish
Estonian
Basque
Persian
Finnish
Fiji
Code
7079
7082
7089
7165
7168
7176
7178
7185
7265
7273
7282
7285
7289
7365
7378
7383
7384
7387
7465
7473
7487
7565
7575
7576
7577
7578
7579
7583
7585
7589
7665
Language Name
Faroese
French
Frisian
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Indonesian
Icelandic
Italian
Hebrew
Japanese
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean
Kashmiri
Kurdish
Kirghiz
Latin
Code
7678
7679
7684
7686
7771
7773
7775
7776
7778
7779
7782
7783
7784
7789
7865
7869
7876
7879
7982
8065
8076
8083
8084
8185
8277
8279
8285
8365
8368
8372
8373
Language Name
Lingala
Laothian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Oriya
Panjabi
Polish
Pashto, Pushto
Portuguese
Quechua
Rhaeto-Romance
Romanian
Russian
Sanskrit
Sindhi
Serbo-Croatian
Singhalese
Code
8375
8376
8377
8378
8379
8381
8382
8385
8386
8387
8465
8469
8471
8472
8473
8475
8476
8479
8482
8484
8487
8575
8582
8590
8673
8679
8779
8872
8979
9072
9085
Language Name
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Tonga
Turkish
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
Chinese
Zulu
44
Troubleshooting
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple mea-
sures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and con-
tact your authorized YAMAHA dealer or service center for help.
Play does not commence even when title
is selected.
Confirm the Ratings setting.
Symptom [DVD] Remedy
Symptom (Common) Remedy
No power.
Power is automatically switched to the
standby mode.
ÁPlay fails to start even when PLAY is
pressed.
ÁPlay commences but then stops
immediately.
No picture.
ÁNo sound.
ÁDistorted sound.
Picture is distorted during rapid advance
or rapid reverse.
No rapid advance (or rapid reverse) play.
No 4:3 (16:9) picture.
No on-screen display.
No surround sound.
No operations can be performed with the
remote control.
No key operation (by the unit and/or the
remote control) is effective.
GUI Screen not displayed or only partially
displayed on the TV Screen.
Insert the AC mains lead securely into the power outlet.
The power is automatically switched to the standby mode after approx.
30 minutes have elapsed in the stop mode (auto turn-off function). Turn the power
back on.
ÁCondensation has formed: wait about 1 to 2 hours to allow the player to dry out.
ÁThis player cannot play discs other than DVDs, Video CDs and CDs.
ÁThe disc may be dirty and may require cleaning.
ÁEnsure that the disc is installed with the label side up.
ÁEnsure that the equipment is connected properly.
ÁEnsure that the input setting for the TV is an Audio/Video (AV) position, e.g. AV1,
AV2.
ÁEnsure that the equipment is connected properly.
ÁEnsure that the input settings for the TV and stereo system are proper.
The picture will be somewhat distorted at times: this is normal.
Some discs may have sections which prohibit rapid advance (or rapid reverse).
Choose the correct setup TV Aspect item which matches the TV set used.
The Off setting is selected for On-Screen Messages: select On”.
Choose the correct setup at the Speaker setting which matches your stereo
system.
ÁCheck the batteries are installed with the correct polarities (o and p).
ÁThe batteries are depleted: replace them with new ones.
ÁPoint the remote control unit at the remote control sensor and operate.
ÁOperate the remote control unit at a distance of not more than 7 meters from the
remote control sensor.
ÁRemove the obstacles between the remote control unit and remote control sensor.
Switch the power to the standby mode and then return to ON. Alternatively, switch
the power to the standby mode, disconnect the AC mains lead and then re-connect
it. (The player may not be operating properly due to lightning, static electricity or
some other external factor.)
Select the appropriate TV screen type by consulting the operation manual of the TV.
45
Self-diagnosis display function
When an error or trouble is detected during operation, a service number appears in the display window.
When a service number has appeared, check out the details given below.
Service number
U11
H Å Å
Player status
Disc is dirty.
Trouble is likely to have occurred. The
number following “H” differs depending
on the status of the player.
Remedy
Wipe the disc clean.
Switch the power to the standby mode and then return to ON.
Alternatively, switch the power to the standby mode,
disconnect the AC mains lead and then re-connect it.
If the service number fails to be cleared even when the
remedial action is taken, ask for the service engineer to repair
the player.
Symptom [DVD] Remedy
Audio soundtrack and/or subtitle
language is not the one selected at the
initial settings.
The menu is displayed in French
(example).
Lightening and darkening of the picture.
No subtitles.
Alternative audio soundtrack (or subtitle)
languages fail to be selected.
Angle cannot be changed.
The password for age restriction has
been forgotten.
If the audio soundtrack and/or subtitle language does not exist on the disc, the
language selected at the initial settings will not be seen/heard.
The setup Menus of Disc Languages is set to French: select English.
Some discs will be copy protected at the direction of copyright owners. During
playback of those discs, picture may not be normally played back when video
signals containing a copy protected signal are played back through a VCR. It is
recommended to connect the DVD/Video CD/CD player directly to an AV amplifier
or to a TV set, not through a VCR.
ÁSubtitles appear only with discs which contain them.
ÁSubtitles are cleared from the TV monitor. Perform the steps on page 27 to display
the subtitles.
ÁAn alternative language is not selected with discs which do not contain more than
one language.
ÁIn the case of some discs, the alternative language cannot be selected by
operating the AUDIO or SUBTITLE button. Try selecting it from the DVD menu if
one is available.
This function is dependent on software availability. Even if a disc has a number of
angles recorded, these angles may be recorded for specific scenes only (when
ANGLE lights up on the FL display.)
While the unit is in the stop mode, hold the units 0SKIP button and the STILL/
PAUSE button down simultaneously and then hold the POWER button down for
longer than 3 seconds (until Initialized disappears from the TV monitor). The lock
will be released and all initial settings will return to the default values.
Symptom [Video CD] Remedy
No menu play. This function works only for Video CDs with playback control.
46
Definition of terms
Angle
Recorded onto some DVD discs are scenes which have been
simultaneously shot from a number of different angles (the
same scene is shot from the front, from the left side, from the
right side, etc.). With such discs, the ANGLE button can be
used to view the scene from different angles.
Chapter number
These numbers are recorded on DVD discs. A title is subdi-
vided into many sections, each of which is numbered, and
specific parts of video presentations can be searched quickly
using these numbers.
DVD
This refers to a high-density optical disc on which high-quality
pictures and sound have been recorded by means of digital
signals. Incorporating a new video compression technology
(MPEG II) and high-density recording technology, DVD en-
ables esthetically pleasing full-motion video to be recorded
over long periods of time (for instance, a whole movie can be
recorded).
DVD has a structure consisting of two 0.6 mm thin discs
which are adhered to each other. Since the thinner the disc,
the higher the density at which the information can be record-
ed, a DVD disc has a greater capacity than a single 1.2 mm
thick disc. Since the two thin discs are adhered to each other,
there is the potential to achieve double-sided play sometime
in the future for even longer duration play.
Playback control
This is recorded on a Video CD (version 2.0). The scenes or
information to be viewed (or listened to) can be selected in-
teractively with the TV monitor by looking at the menu shown
on the TV monitor.
Subtitles
These are the printed lines appearing at the bottom of the
screen which translate or transcribe the dialogue. They are
recorded on DVD discs.
Time number
This indicates the play time which has elapsed from the start
of a disc or a title. It can be used to find a specific scene
quickly. (It may not work with some discs.)
Title number
These numbers are recorded on DVD discs. When a disc
contains two or more movies, these movies are numbered as
title 1, title 2, etc.
Track number
These numbers are assigned to the tracks which are record-
ed on Video CDs and CDs. They enable specific tracks to be
located quickly.
Video CD
This contains recordings of pictures and sound whose quality
is on a par with that of videotape. This player also supports
Video CDs with playback control (version 2.0).
47
Specifications
Power
requirements: For Continental Europe, United
Kindom and Australia models
AC 220240 V, 50 Hz
For other models
AC 110240 V, 50/60 Hz
Power
consumption: 22 W (approx. 4 W when set to
standby mode by the STANDBY/
ON button or the remote control)
Audio output:
Output level: 2 Vrms (1 kHz, 0 dB)
Output connector: Pin jack
5.1ch mixed output: 1 system (2ch)
5.1ch discrete output: 1 system (5.1ch)
Audio signal output characteristics:
(1) Frequency response:
ÁDVD (linear audio):
Á2 Hz22 kHz (48 kHz sampling)
Á2 Hz44 kHz (96 kHz sampling)
ÁCD audio: 2 Hz20 kHz (EIAJ)
(2) S/N ratio:
ÁCD audio: 115 dB (EIAJ)
(3) Dynamic range:
ÁDVD (linear audio): 102 dB
ÁCD audio: 99 dB (EIAJ)
(4) Total harmonic distortion:
ÁCD audio: 0.0025% (EIAJ)
Digital audio output:
Optical digital output: Optical connector
Coaxial digital output: pin jack
Pickup: Wave length: 655 nm
Laser power: CLASS 2
Specifications are subject to change without notice.
Weight and dimensions are approximate.
Signal system: For Continental Europe, United
Kingdom and Australia models
PAL 625/50, PAL 525/60
For other models
NTSC/PAL
Weight: 3.6 kC
Dimensions: 435 (W)q284 (D)q87.5 (H) mm
(excluding protrusions)
Operating temperature range:
o5 to o35uC
Operating humidity range:
5 to 90% (no condensation)
Discs played:
(1) DVD-VIDEO disc
12 cm single-sided, single-layer
12 cm single-sided, double-layer
12 cm double-sided, double-layer (one layer per side)
8 cm single-sided, single-layer
8 cm single-sided, double-layer
8 cm double-sided, double-layer (one layer per side)
(2) Compact disc (CD-DA, VIDEO CD)
12 cm disc
8 cm disc
S-video output:
Y output level: 1 Vp-p (75°)
C output level: 0.300 Vp-p (75°)
Output connector: S terminal (1 system)
Video output:
Output level: 1 Vp-p (75°)
Output connector: Pin jack (2 systems)
Region Management Information
Region Management Information: This DVD/VIDEO CD/CD player is designed and manufactured to respond to the Region Manage-
ment Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Re-
gion number of this DVD/VIDEO CD/CD player, this DVD/VIDEO CD/CD player cannot play this disc.
For Continental Europe and United Kingdom models
The Region number for this DVD/VIDEO CD/CD player is 2.
For Australia model
The Region number for this DVD/VIDEO CD/CD player is 4.
For other models
The Region number for this DVD/VIDEO CD/CD player is 3.
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technol-
ogy must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless oth-
erwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
2 43
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. PA PARIS-EST RUE AMBROISE CROIZAT CROISSY-BEAUBOURG BP70-77312 MARNE LAVALLEE, CEDEX 2 FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
VQT7523-1 Printed in Japan

Transcripción de documentos

DVD/VIDEO CD/CD PLAYER DVD-S700 Before attempting to connect, operate or adjust this product, please read this Operating Instructions manual completely. Please save this manual. Operating Instructions Safety information Note: For Continental Europe, United Kingdom and Australia models This unit can be used only where the power supply is AC 220–240 V, 50 Hz. It cannot be used elsewhere. For other models This unit can be used only where the power supply is AC 110–240 V, 50/60 Hz. It cannot be used elsewhere. CAUTION: DVD/VIDEO CD/CD PLAYER IS A CLASS 1 LASER PRODUCT. HOWEVER THIS DVD/VIDEO CD/CD PLAYER USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE DVD/VIDEO CD/CD PLAYER CORRECTLY AS INSTRUCTED. WHEN THIS DVD/VIDEO CD/CD PLAYER IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS PLAYER. CAUTION -LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM. ATTENTION-RAYONNEMENT LASER EN CAS D'OUVERTURE. NE PAS REGARDER DANS LE FAISCEAU. VORSICHT -LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET. NICHT IN DEN STRAHL BLICKEN. ADVARSEL -LASERSTRÅLING VED ÅBNING. SE IKKE IND I STRÅLEN. ADVARSEL -LASERSTRÅLING NÅR DEKSEL ÅPNES. STIRR IKKE INN I STRÅLEN. VARNING -LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD. STIRRA EJ IN I STRÅLEN. VARO! -AVATTAESSA OLET ALTTIINA LASERSÄTEILYLLE. ÄLÄ TUIJOTA SÄTEESEEN. 注意 - ここを開くとレーザー光が出ます。  レーザー光をのぞき込まないでください。 (Inside of product) CLASS 1 LASER PRODUCT USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION! This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power. 2 (Back of product) Caution for AC mains lead (For United Kingdom) For your safety please read the following text carefully This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS 1362. Check for the ASTA mark ! or the BSI mark " on the body of the fuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET. How to replace the Fuse ÁThere are two types of the supplied AC Mains Lead: ) and * as shown below. 1 Open the fuse compartment with a screwdriver. 2 Replace the fuse and fuse cover. TYPE ) 1 2 TYPE * 1 2 If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt please consult a qualified electrician. If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below. Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet. IMPORTANT The wires in this mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED. Under no circumstances should either of these wires be connected to the earth terminal of the three pin plug, marked with the letter E or Earth Symbol #. 3 Dear Customers Accessories May we take this opportunity to thank you for purchasing this YAMAHA DVD/VIDEO CD/CD player. We strongly recommend that you carefully study the Operating Instructions before attempting to operate the unit and that you note the listed precautions. Please check and identify the supplied accessories. Features È DVD: a completely new dimension in video entertainment ÁSubtitles may be displayed in one of a maximum of 32 languages\. ÁThe audio soundtrack can be heard in up to 8 languages\. ÁThe multi-angle function allows you to choose the viewing angle of scenes which were shot from a number of different angles. (Limited to DVD recorded with multiple camera angles.) Remote control unit . . . . . . . . . . . . . . 1 \ The number of the languages recorded is dependent on the software. È High quality digital audio ÁThe Dolby Digital (AC-3)/MPEG 1/2 2–5.1ch audio/Linear PCM decoder is built into the player which makes it possible to enjoy Multi-Channel Surround sound. ÁWith the linear PCM sound of a 48 kHz/16 bit through 96 kHz/24 bit, audio quality exceeding that of CDs becomes possible. Batteries . . . . . . . . . 2 for remote control unit [size “AA” (R6P)] È Many convenient features ÁGUI (Graphical User Interface) screens for showing the disc information or player information and providing access to many major functions of this unit ÁProgramming of up to 5 scenes in memory (markers) ÁParental lock settings to prevent play of discs unsuitable for some audiences [DVD only] AC mains lead . . . . . 1 (For United Kingdom model) È Compatible with PAL DVD (Video CD) and NTSC DVD (Video CD) ÁThis player can play discs recorded in either PAL or NTSC format. For Continental Europe, United Kingdom and Australia models However, the player must be connected to a PAL TV which is capable of receiving PAL 525/60 system to play both PAL DVD (Video CD) and NTSC DVD (Video CD). For other areas models However, the player must be connected to a Multi-system TV to play both PAL DVD (Video CD) and NTSC DVD (Video CD). The use of a Multi-system TV is recommended. È Compatible with Video CD and CD as well as DVD AC mains lead . . . . . 1 (For Australia model) AC mains lead . . . . . 1 (For Continental Europe models and other models) È Disc formats supported by this player The unit can play back discs bearing any of the following marks: Video/audio cord . . . . . . . . . . . . . 1 4 DVD Video CD CD [8 cm disc/ 12 cm disc] [8 cm disc/ 12 cm disc] [8 cm disc/ 12 cm disc] Table of contents Getting Started: Safety information . . . . . . . . . . . . . . . . . . . . . Caution for AC mains lead (For United Kingdom) . . . . . . . . . . . . . . . . . . . . Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . Selecting the type of disc for the type of the connected TV (For other areas) . . . . . . . . . . . Control reference guide . . . . . . . . . . . . . . . . . Front panel display . . . . . . . . . . . . . . . . . . . . . Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote control preparation . . . . . . . . . . . . . . Before enjoying DVD/Video CD/CD . . . . . . . . Advanced Operation: 2 3 4 4 6 6 7 9 10 13 14 Basic Operation: Basic play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 ÁBasic play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 ÁStopping play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 ÁSkipping ahead or back . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Rapid advance (Rapid reverse) . . . . . . . . . . . Still picture (Pause) . . . . . . . . . . . . . . . . . . . . Frame advance [DVD/Video CD] . . . . . . . . . . . . . Slow-motion play [DVD/Video CD] . . . . . . . . . . . Enjoying Video CDs with playback control without using menus [Video CD only] . . . . . . 17 17 17 18 18 Operation Using GUI Screens: General information about GUI screens . . . . 19 Program play [Video CD/CD] . . . . . . . . . . . . . . . 22 Random play [Video CD/CD] . . . . . . . . . . . . . . . 23 Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 ÁRepeat viewing (listening) . . . . . . . . . . . . . . . . . . . . . . . . 24 ÁRepeating sections between two specific points (A-B repeat) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Storing markers in memory to be viewed (listened) again . . . . . . . . . . . . . . . . . . . . . . 26 ÁStoring a marker in the memory . . . . . . . . . . . . . . . . . . . . 26 ÁRecalling/clearing a marker . . . . . . . . . . . . . . . . . . . . . . . 26 Changing subtitle language [DVD only] . . . . . . 27 Changing audio soundtrack language [DVD only] . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switching vocals ON or OFF for Karaoke discs [DVD/Video CD] . . . . . . . . . . . . . . . . . . . Viewing from another angle [DVD only] . . . . . . Using a title menu [DVD only] . . . . . . . . . . . . . . Using a DVD menu [DVD only] . . . . . . . . . . . . . 28 28 29 30 30 Initial Settings: Initial settings . . . . . . . . . . . . . . . . . . . . . . . . . 31 ÁCommon procedures of initial settings . . . . . . . . . . . . . . . ÁSelecting disc languages [DVD only] . . . . . . . . . . . . . . . . ÁSelecting rating level [DVD only] . . . . . . . . . . . . . . . . . . . ÁSelecting language of On-Screen Display menu . . . . . . . ÁSwitching the On-Screen Display ON or OFF . . . . . . . . . ÁSelecting the display brightness . . . . . . . . . . . . . . . . . . . . ÁSelecting TV screen type . . . . . . . . . . . . . . . . . . . . . . . . . ÁSelecting digital output . . . . . . . . . . . . . . . . . . . . . . . . . . . ÁSpeaker setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ÁOther settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 32 33 34 35 35 36 37 39 41 ÁCommon procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Detailed descriptions of each GUI icon . . . . 20 ÁScreen for disc information . . . . . . . . . . . . . . . . . . . . . . . . 20 ÁScreen for player information . . . . . . . . . . . . . . . . . . . . . . 21 ÁScreen for slow-motion play and rapid advance (reverse) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 For Your Reference: Disc handling and maintenance . . . . . . . . . . 42 Language code list . . . . . . . . . . . . . . . . . . . . . 43 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 44 Self-diagnosis display function . . . . . . . . . . . 45 Definition of terms . . . . . . . . . . . . . . . . . . . . 46 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 47 Region Management Information . . . . . . . . . . . . . . . . . . Back cover 5 Precautions Please read these precautions before operating this unit. Selecting the type of disc for the type of connected TV È Mains lead protection (For other models) To avoid any malfunctions of the unit, and to protect against electric shock, fire or personal injury, please observe the following. ÁHold the plug firmly when connecting or disconnecting the AC mains lead to this unit. ÁDo not connect or disconnect the AC mains lead when your hands are wet. ÁKeep the AC mains lead away from heating appliances. ÁNever put any heavy object on the AC mains lead. ÁDo not attempt to repair or reconstruct the AC mains lead in any way. ÁRemove dust, dirt, etc. on the plug at regular intervals. ÁIf the unit has been dropped or otherwise damaged, set the unit to the standby mode and disconnect the AC mains lead. ÁIf smoke, malodors or noises are emitted from the unit, set the unit to the standby mode and disconnect the AC mains lead. È Placement Avoid placing the unit in areas of: Ádirect sunlight or heating radiators, or closed automobiles Áhigh temperature (over 35uC) or high humidity (over 90%) Áexcessive dust Ávibration, impact or where the surface is tilted As the internal parts may be seriously damaged. Both DVDs and Video CDs have the material recorded in the PAL and NTSC systems. Refer to the table below to select the correct disc type for the type of connected TV. È Connecting to the Multi-system TV Disc Played in the PAL system. PAL Played in the NTSC system. NTSC È Connecting to the NTSC TV Disc È Non-use periods When the unit is not being used, switch the unit to the standby mode. When left unused for a long period of time, the unit should be unplugged from the household AC outlet. TV Monitor TV Monitor No clear images are shown on the screen. PAL È No fingers or other objects inside ÁTouching internal parts of this unit is dangerous, and may cause serious damage to the unit. Do not attempt to disassemble the unit. ÁDo not put any foreign object on the disc tray. È Keep away from water and magnets. ÁKeep the unit away from flower vases, tubs, sinks, etc. If liquids are spilled into the unit, serious damage could occur. ÁNever bring magnetic objects such as speakers near to this unit. È Stacking ÁPlace the unit in a horizontal position, and do not place anything heavy on it. ÁDo not place the unit on amplifiers or other equipment which may become hot. È Condensation Moisture may form on the lens in the following conditions… Áimmediately after a heater has been turned on. Áin a steamy or very humid room. Áwhen the unit is moved from a cold environment to a warm one. If moisture forms inside this unit, it may not operate properly. In this case, turn on the power and wait about one hour for the moisture to evaporate. È If there is noise interference on the TV while a broadcast is being received Depending on the reception condition of the TV, interference may appear on the TV screen while you are watching a TV broadcast and the unit is left on. This is not a malfunction of the unit or the TV. To watch a TV broadcast, switch this unit to the standby mode. 6 Played in the NTSC system. NTSC È Connecting to the PAL TV Disc PAL TV Monitor Played in the PAL system. However, the initial settings and Video CD’s “Program Play” functions cannot be used. No clear images are shown on the screen. NTSC Note: When a disc which does not comply with Video CD standard is played, the bottom part of the picture may disappear. Control reference guide Main unit 1 2 3 4 5 6 NATURAL SOUND DVD PLAYER DVD-S700 f OPEN/CLOSE STOP STANDBY/ON DVD / VIDEO CD / CD 7 e STANDBY/ON button . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Press to switch the unit to ON from Standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. Standby mode In this state, this unit consumes a very small quantity of power to receive infrared-signals from the remote control transmitter. SKIP STILL/PAUSE ; PLAY DIGITAL 8 Page : 9 0 Page g h i j k l m n Remote control signal sensor . . . . . . . . . . . . . . . . . . . 13 Display window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 OPEN/CLOSE button . . . . . . . . . . . . . . . . . . . . . . . . . . 14 SKIP buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 16 Disc tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 STOP button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 STILL/PAUSE button . . . . . . . . . . . . . . . . . . . . . . . . . . 17 PLAY button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 f STANDBY indicator When the unit is connected to the AC mains supply, this indicator lights up in standby mode and goes out when the unit is turned on. 7 Control reference guide Remote control unit Page e f g h i j k l m n o p q r s t u v w x y POWER */I button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 STOP button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 SKIP buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 16 TITLE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 30 Cursor buttons/SELECT button . . . . . . . . . . . . . . . . . 15 ON SCREEN button . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 SUBTITLE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 MARKER button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 PLAY MODE button . . . . . . . . . . . . . . . . . . . . . . . . 22, 23 REPEAT button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 A-B button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 SET UP button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 STILL/PAUSE button . . . . . . . . . . . . . . . . . . . . . . . . . . 17 OPEN/CLOSE button . . . . . . . . . . . . . . . . . . . . . . . . . . 14 PLAY button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 SLOW/SEARCH buttons . . . . . . . . . . . . . . . . . . . . 17, 18 MENU button . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 18, 30 RETURN button . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 19 AUDIO button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 ANGLE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Numeric buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 ÁTo select a 2-digit number Example: To select track 23 Press “X10”, “2” and then “3”. z CLEAR button . . . . . . . . . . . . . . . . . . . . . . . 19, 23, 26, 32 8 q 1 2 3 4 5 OPEN/CLOSE POWER */ I @STOP H gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G MENU TITLE SELECT 7 8 9 0 o p AUDIO s t u v 6 ON SCREEN SUBTITLE r RETURN ANGLE w x MARKER PLAY MODE y REPEAT A-B CLEAR SET UP DVD z Front panel display e Rotates during play. Rotates fast clockwise or counterclockwise during rapid advance (reverse). (See page 17.) Rotates slowly clockwise or counterclockwise during slow-motion play. [DVD/Video CD] (See page 18.) 12 34 DVD ANGLE PROG. 89 0o r 5 6 7 96kHz 24bit pq Illuminates in the stop mode. f Illuminates during playback. Flashes when the RESUME function is ON. (See page 16.) g Illuminates during repeat play. (See pages 24 and 25.) h Illuminates in the pause mode. [CD] (See page 17.) i Indicates the chapter number. [DVD] Indicates the track number. [Video CD/CD] j Indicates the total playing time when the disc tray is closed. [Video CD/CD] Indicates the elapsed playing time from the start of the title/track during play. k Indicates the current audio channel information recorded in the disc (e.g. 2ch or 5.1ch). l Illuminates when a DVD is loaded. m Illuminates in the still picture mode. [DVD/Video CD] (See page 17.) n Illuminates during program play. [Video CD/CD] (See pages 22 and 23.) o Illuminates when it is possible to switch the angle [DVD] (See page 29.) p Illuminates when Linear PCM of 96 kHz sampling is being played. q Illuminates when Linear PCM of 24 bit is being played. r Illuminates when the disc tray is open. s Illuminates when the disc tray is being closed (retracted). t Illuminates during play of a DVD. u Illuminates during play of an interactive DVD.\ v Illuminates during play of a Karaoke DVD. w Illuminates during play of an interactive Karaoke DVD.\ x Illuminates during play of a Video CD. y Illuminates during play of a Video CD with playback control. z Illuminates during play of a CD. { Illuminates when playback is impossible. ÁDVDs for which playback is prohibited by the setup “Ratings”. (See page 33.) For Continental Europe and United Kingdom models ÁDVDs with Region No. other than “2” or “ALL”. For Australia model ÁDVDs with Region No. other than “4” or “ALL”. For other models ÁDVDs with Region No. other than “3” or “ALL”. (See page 42.) | Illuminates when no disc is loaded. \ An interactive DVD is a DVD software which includes multiple angles, stories and so on. s t DVD u DVD v DVD w DVD x y z { | 9 Connection Never plug in this unit and other components until all connections are completed. ÁBe sure that the colors of the connectors and plugs match up when connecting the cord. ÁRead through the instructions for the equipment to be connected. Connecting to an AV amplifier containing Dolby Digital (AC-3)/MPEG 1/2 2–5.1ch audio decoder When DVDs recorded in Dolby Digital or MPEG audio are played, Dolby Digital bitstream or MPEG audio bitstream is output from the player’s OPTICAL digital audio output connector or COAXIAL digital audio output connector. When the player is connected to a Dolby Digital decoder or MPEG audio decoder, you can enjoy theater-quality audio in your home. [An optical digital cable or coaxial audio cable (both optional) is required when an optional Dolby Digital decoder or MPEG audio decoder is used.] COAXIAL TV set (optional) AUDIO SIGNAL VIDEO SIGNAL R L VIDEO S-VIDEO DVD/ LD DVD/LD OPTICAL DVD/ LD Coaxial audio cable (optional) Optical digital cable (optional) Video/audio cord (supplied) S-video cord (optional) AV amplifier with Dolby Digital (AC-3)/ MPEG audio decoder (optional) DVD/VIDEO CD/CD player 6CH DISCRETE COAXIAL CENTER SURROUND L L MIXED 2CH MAIN L VIDEO 1 AC IN S VIDEO PCM/U DIGITAL MPEG OPTICAL R DIGITAL SUBWOOFER AUDIO OUT R R 2 VIDEO OUT S-video output connector The S (separate) video output connector separates the color (C) and luminance (Y) signals before transmitting them to the TV set in order to achieve a sharper picture. Use the S-video cord (optional) when connecting the player to a TV set equipped with an S-video input connector for the best picture clarity possible. Notes: ÁDuring DVD play, the TV volume may be at a lower level than during TV broadcasts, etc. If this is the case, adjust the volume to the desired level. 10 AC mains lead (supplied) To power outlet \ The configuration of the plug differs according to the area. ÁIf the DVD player is connected to the TV through a video cassette recorder, the picture may not be played back normally with some DVDs. If this is the case, do not connect the player via the VCR. Connection Notes when connecting the optical digital cable ÁRemove the dust protection cap from the connector and connect the cable firmly so that configurations of both the cable and the connector match. ÁKeep the dust protection cap and always reattach the cap when not using the connector to protect against dust. Dust protection cap Concerning the audio output from the unit’s optical/coaxial digital audio output connector Disc Sound recording format Optical/coaxial digital audio output from connector DVD Dolby Digital (AC-3) Dolby Digital bitstream (2–5.1ch) or PCM (2ch) (48 kHz/16 bit)\1 Linear PCM (48/96 kHz 16/20/24 bit) Linear PCM (2ch) (48 kHz sampling/16 bit only)\2 or no output\1 MPEG MPEG audio bitstream or PCM (2ch) (16 bit)\1 Video CD MPEG 1 PCM (44.1 kHz sampling) CD Linear PCM Linear PCM (44.1 kHz sampling) Caution for the optical/coaxial digital audio output connector: ÁDo not connect an amplifier (with an optical/coaxial digital input connector) which does not contain the Dolby Digital (AC-3) or MPEG audio decoder. ÁOtherwise any attempt to play DVDs may cause to such a high level of noise that it may be harmful to your ears and damage your speakers. ÁVideo CDs and CDs can be played as they would normally be played. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. j 1992–1997 Dolby Laboratories, Inc. All rights reserved. \1 The type of audio output from the connector can be selected by the initial settings. (See page 37.) \2 Sound having 96 kHz sampling converted into 48 kHz sampling when it is output from the unit’s optical/coaxial digital audio output connector. For your reference: ÁDolby Digital (AC-3) is a digital sound compression technique developed by the Dolby Laboratories Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel) sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc. ÁLnear PCM is a signal recording format used in CDs. While audio CDs are recorded in 44.1 kHz/16 bit, DVDs are recorded in 48 kHz/16 bit up to 96 kHz/24 bit. ÁIf you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1-channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark. 11 Connection Connecting to an AV amplifier which does not contain Dolby Digital (AC-3)/MPEG audio decoder This DVD/VIDEO CD/CD player contains a Dolby Digital (AC-3)/MPEG audio decoder. This enables the playback of DVDs recorded in Dolby Digital Surround, MPEG audio or Linear PCM without the need for an optional decoder with Dolby Digital, MPEG audio or Linear PCM processing. When the DVD player is connected to an AV amplifier with 5.1ch input connectors, you can enjoy theaterquality audio right in your home when playing discs recorded in Dolby Digital Surround, MPEG audio or Linear PCM. TV set (optional) VIDEO SIGNAL 6CH DISCRETE INPUT DVD/LD CENTER SURROUND MAIN AUDIO SIGNAL L L R R SUB WOOFER DVD/LD AV amplifier without Dolby Digital (AC-3)/ MPEG audio decoder (optional) Audio cord (optional) Video/audio cord (supplied) DVD/VIDEO CD/CD player 6CH DISCRETE COAXIAL CENTER SURROUND L L MIXED 2CH MAIN L VIDEO 1 AC IN S VIDEO PCM/U DIGITAL MPEG OPTICAL R DIGITAL SUBWOOFER AUDIO OUT R R 2 VIDEO OUT Notes: ÁAfter connection is made, set the “Speaker setting” (such as Yes/No and Large/Small) according to your speaker system. (See page 39.) ÁIf the surround speakers or the center speaker can’t be installed at an equal distance to (or further away from) the front speakers from the listening position, then change the delay time setting at the “Speaker setting” on page 39, to compensate. 12 ÁIf the surround speakers are set to “None” at the “Speaker setting” (see page 39), the discs recorded in MPEG 2 audio or Linear PCM will be played back only in 2 channels even when the center speaker is connected as well as the front speakers. ÁDVDs recorded in Linear PCM/96 kHz sampling in which “Center Speaker” is contained will also be played back only in 2ch. Remote control preparation Battery installation A ) Insert the batteries while observing the correct (o) and (p) polarities as illustrated at right. 7 Service life of batteries ÁThe batteries normally last for about one year although this depends on how often and for what operations the remote control is used. ÁIf the remote control unit fails to work even when it is operated near the player, replace the batteries. ÁUse size “AA” (R6P) batteries. Notes: ÁDo not use rechargeable (Ni-Cd) batteries. ÁDo not attempt to recharge, short-circuit, disassemble, heat or throw the batteries into the fire. ÁDo not drop, step on or otherwise impact the remote control unit. This may damage the parts or lead to malfunction. ÁDo not mix old and new batteries. ÁIf the remote control unit is not going to be used for a long time, remove the batteries. Otherwise, electrolyte may leak which may lead not only to malfunctioning but also to burns if contact is made with the electrolyte. ÁWipe away any electrolyte leaking inside the remote control unit, and install new batteries. ÁIf any electrolyte should come into contact with parts of your body, wash it off thoroughly with water. Remote control operation range * 8 7 B Remote control signal sensor Point the remote control unit no more than about 7 m from the remote control sensor and within about 60u of the front of the unit. ÁThe operating distance may vary according to the brightness of the room. Notes: ÁDo not point bright lights at the remote control sensor. ÁDo not place objects between the remote control unit and the remote control sensor. ÁDo not use this remote control unit while simultaneously operating the remote control unit of any other equipment. 8 7m 30˚ 30˚ 13 Before enjoying DVD/Video CD/CD The On-Screen menu language of your player has been factory pre-set to English. If you would like to change the menu language to French, Spanish, German or Italian (for Continental Europe, United Kingdom and Australia models) or to French or Spanish (for other models), please refer to “Selecting language of On-Screen Display menu” on page 34. In the explanations given below it is assumed that English has been selected as the menu language. 2 f OPEN/CLOSE f OPEN/CLOSE STOP / CD SKIP : STILL/PAUSE PLAY ; PLAY DIGITAL Basic play Preparations ÁSwitch the TV ON and select the Audio/Video (AV) position, e.g. AV1, AV2, which has been connected to the player. ÁSwitch on the stereo system’s power if the player has been connected to a stereo system. 3 Basic play 1 Press POWER to switch on the power. 2 Press OPEN/CLOSE to open the disc tray. 1 2 Open 2 3 OPEN/CLOSE Place a disc onto the disc tray. OPEN/CLOSE POWER Hold the disc without touching either of its surfaces, position it with the printed title side facing up, align it with the guides, and place it in its proper position. e 8 cm disc f 12 cm disc */ I @STOP H 1 gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G TITLE MENU SELECT 4 Press PLAY. ON SCREEN SUBTITLE Close Reading 4 DPLAY AUDIO RETURN ANGLE MARKER PLAY MODE REPEAT The disc tray is automatically closed and play begins. ÁWhen the disc tray is closed by pressing OPEN/CLOSE, press PLAY to commence play. ÁWhen a menu screen appears on the TV monitor In case of interactive DVDs or Video CDs with playback control, a menu screen appears on the TV monitor. Perform step 5 on page 15 to commence play. TITLE MENU Dogs Castles Lovers Birds 14 (Example of DVD) A-B CLEAR SET UP DVD 4 Basic play 5 Press C/D/A/B and press SELECT, or press the numeric button(s), to select the preferred item. : SKIP ; ÁC/D/A/B are not effective for selecting items for Video CDs. TITLE MENU f OPEN/CLOSE Birds Dogs Castles : STOP SKIP STILL/PAUSE ; PLAY oftheworld Lovers Birds / CD DIGITAL Play of the selected item now begins. When the menu continues onto another screen After step 4 on page 14, press SKIP I. (SKIP buttons may not be effective depending on the disc.) 1 EAST ASIA 2 SOUTH ASIA 3 MIDDLE EAST 4 AFRICA 5 EUROPE H SKIP I : SKIP ; 6 OCEANIA 7 NORTH AMERICA 8 CENTRAL AMERICA 9 SOUTH AMERICA 10 ANTARCTIC ÁTo return to the previous menu screen Press H SKIP. ÁFor operation, refer also to the jacket of the disc concerned. OPEN/CLOSE POWER */ I @STOP Stopping play and returning to the menu screen ÁDVD Press TITLE, MENU or RETURN. (Which button is pressed differs depending on the disc used.) ÁVideo CD Press RETURN. When the unit is not in use, remove the disc and press POWER to switch the power to the standby mode. The power will automatically be switched to the standby mode after 30 minutes or so have elapsed in the stop mode. (Auto turn-off function) SKIP I DPLAY MENU SLOW/ F SEARCH G */ I TITLE H MENU RETURN SKIP I SELECT TITLE ÁPlay is suspended, and the menu screen is displayed. After operation H POWER gSTILL/PAUSE ON SCREEN SUBTITLE AUDIO RETURN ANGLE MARKER 5 5 PLAY MODE REPEAT A-B CLEAR SET UP DVD What is playback control? If a Video CD has “playback control” written on its disc or jacket, it means that particular scenes or information can be selected for viewing interactively with the TV monitor using the menu screen. 15 Basic play Note: ÁThe disc continues to rotate while the menu is displayed even after the player has finished playing a particular item. When no further selections are to be played, be sure to press the STOP button to clear the menu display. ÁIf the disc is placed in upside down (and it is a single sided disc), the DVD display will indicate “NO DISC”. For Continental Europe, United Kingdom and Australia models ÁWhen the NTSC DVD/Video CD is played, the playback picture may roll up or down on some TVs; adjust this using the V-HOLD control on the TV. TVs not equipped with a VHOLD control cannot correct this condition. The playback picture may shrink vertically and black bars may appear both on the top and bottom of the screen, or the picture may be in black and white. This does not indicate a malfunction. SKIP : f OPEN/CLOSE : STOP SKIP STILL/PAUSE / CD ; PLAY DIGITAL PLAY STOP For your reference: ÁWhen —— appears while a button is being operated, it means that the corresponding operation is prohibited by the player or the disc. Stopping play DPLAY Press STOP. OPEN/CLOSE POWER */ I @STOP For your convenience: ÁWhen play is stopped, the unit records the point where STOP was pressed (RESUME function). (“D” flashes on the unit’s display when this function is activated.) Press PLAY again, and play will resume from this point. When the tray is opened or STOP is pressed again, the RESUME function will be cleared. The RESUME function works only with discs for which the elapsed playing time appears on the unit’s display during playback. This feature will not be cleared when the power is switched to the standby mode and then returned to ON. H @STOP H gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G MENU TITLE SKIP I SELECT ON SCREEN SUBTITLE AUDIO RETURN ANGLE MARKER PLAY MODE REPEAT Skipping ahead or back A-B CLEAR SET UP DVD [Skipping\ahead] Press SKIP I during play. A chapter (DVD) or a track (Video CD/CD) is skipped each time the button is pressed. [Skipping\back] Press H SKIP during play. When the button is pressed once midway through a chapter/ track, play returns to the start of that chapter/track. When it is pressed again, a chapter/track is skipped each time the button is pressed. For your reference: ÁWhen H SKIP I is pressed during menu play of Video CDs, a menu screen may sometimes be recalled. 16 ; Rapid advance (Rapid reverse) Press play. SLOW/SEARCH F or G during SLOW/ F SEARCH G Reverse Forward direction direction (Example) ÁThe speed of advance (reverse) is relatively slow at first. When the button is pressed again, the speed becomes faster. (Each time the button is pressed, the speed increases up to 5 steps.) DPLAY To return to normal play Press PLAY. OPEN/CLOSE POWER */ I @STOP For your reference: ÁWhen SLOW/SEARCH is used during menu play of Video CDs, a menu screen may sometimes be recalled. H gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G MENU TITLE SELECT gSTILL/PAUSE Still picture (Pause) Press STILL/PAUSE during play. SLOW/ ÁDVD/Video CD: The player will be placed in the still picture mode. ÁCD: The player will be placed in the pause mode. To return to normal play Press PLAY. ON SCREEN SUBTITLE AUDIO RETURN ANGLE F SEARCH G MARKER Still PLAY MODE REPEAT A-B CLEAR SET UP DVD [DVD/Video CD] Frame advance [DVD/Video CD] Press STILL/PAUSE in the still picture mode. The disc is advanced by one frame each time the button is pressed. To return to normal play Press PLAY. Note: ÁWhether the pictures are advanced by a “frame” or “field” is selected automatically. (See page 41.) 17 Slow-motion play [DVD/Video CD] Press SLOW/SEARCH F or G in the still picture mode. (See page 17.) SLOW/ F SEARCH G Reverse Forward direction direction (Example) ÁThe speed of slow-motion is slow at first. When the button is pressed again, the speed becomes faster. (Each time the button is pressed, the speed increases up to 5 steps.) DPLAY To return to normal play Press PLAY. OPEN/CLOSE POWER */ I @STOP For your reference: ÁFor Video CDs, slow-motion playback in reverse direction is not possible. H @STOP gSTILL/PAUSE SKIP I DPLAY MENU SLOW/ F SEARCH G MENU TITLE SELECT Enjoying Video CDs with playback control without using menus [Video CD only] 1. Press STOP after the menu screen appears (after step 4 on page 14). (“PBC” will be cleared from the unit’s display.) 2. Press the numeric button(s) to select the preferred track. (Play begins.) ÁRefer to the jacket etc. of the disc concerned for the track numbers. ÁPress “1” to start play from the beginning of the disc. To return to menu play Press STOP to stop playback and press MENU. (“PBC” will light up on the unit’s display and the menu screen is resumed.) Perform step 5 on page 15. 18 ON SCREEN SUBTITLE AUDIO RETURN ANGLE MARKER PLAY MODE REPEAT A-B SLOW/ F SEARCH G CLEAR SET UP DVD General information about GUI screens A 3 OPEN/CLOSE POWER */ I This unit features GUI (Graphical User Interface) screens consisting of icons showing disc information (title/chapter/ track number, elapsed playing time, audio/subtitle language, and angle) and player information (repeat play, play mode, marker, Karaoke vocal ON/OFF, etc.). Some icons only show the indicated information. Other icons allow the settings to be changed. @STOP H 2 3 Press C/D to select the preferred item. 2 1 AUDIO RETURN ANGLE MARKER PLAY MODE REPEAT 3 A-B CLEAR SET UP DVD CLEAR B 2 AB 35 1:07:48 T LPCM 3 FRA 96k 24b ON 2 ENG 1 12345 C 2 Example of GUI screens (The screens may differ depending on the disc contents.) ÁDVD (*) ÁVideo CD (+) ÁCD (,) For your reference: ÁDepending on the type of DVD software and a TV with automatic picture zoom function enabled, the GUI screen may not be displayed or only partially displayed on the TV screen. In this case, select the appropriate TV screen type by consulting the operation manual of the TV. MENU ON SCREEN SUBTITLE ON SCREEN Press A/B to select the preferred setting. Press ON SCREEN, RETURN or CLEAR to clear the GUI screen. 2 SLOW/ F SEARCH G SELECT ÁThe currently selected item is indicated by the yellow frame on the GUI screen. ÁWhen numbers are displayed (e.g. title No.), the numeric buttons are also effective for setting instead of A/B. ÁFor some functions, the setting will be registered immediately; for others, SELECT must be pressed. DPLAY RETURN Press ON SCREEN during play or in the stop mode. Each time this button is pressed, the TV monitor changes as shown below. [>GUI screen for selecting disc information l v l>GUI screen for selecting player information l v l>GUI screen for slow-motion play and rapid advance l>(reverse) l v {=GUI screen is cleared ÁSome functions cannot be accessed from the stop mode. SKIP I TITLE Common procedures ) 1 SELECT gSTILL/PAUSE AB 7:48 T PRG L R PBC OFF 12345 D 2 AB 7:48 T PRG 12345 19 Detailed descriptions of each GUI icon 1 2 2 35 Screen for disc information No. Remarks Changing method e To show the current title No. [DVD] or track No. [Video CD/CD] and to jump to the desired title No. or track No.\1 A B or Numeric/ SELECT f To show the current chapter No. or to jump to the desired chapter No. [DVD only] A B or Numeric/ SELECT g To show the elapsed time and to directly select scenes by the elapsed time\2 [DVD] or to show the elapsed time [Video CD/CD] Numeric/ SELECT To show the current audio soundtrack language No. and to change to the desired one [DVD only] (See page 28.) A B or Numeric h i j k l To show the audio soundtrack language selected using the above icon [DVD only] To show the audio attribute (type) of the disc currently being played [DVD only] ÁLPCM (Linear PCM), MPEG (MPEG audio) or $ [Dolby Digital (AC-3)] To show the audio attribute (sampling frequency or channel No.) of the disc currently being played [DVD only] ÁFor Linear PCM disc: 48 kHz or 96 kHz ÁFor Dolby Digital (AC-3) disc: 1ch to 5.1ch ÁFor MPEG audio disc: 1ch to 5.1ch To show the audio attribute (bit No.) of the disc currently being played [DVD only] —— n To show the current subtitles language No. and to change to the desired one [DVD only] (See page 27.) o To show the subtitle language selected using the above icon [DVD only] p To display/clear subtitles [DVD only] q (See page 27.) To show the current angle No. and to change to the desired one [DVD only] (See page 29.) s [Video CD only] (See page 28.) ÁLR, L or R To show whether Video CD menu play is ON or OFF [Video CD with playback control 5 LPCM 3 FRA 96k 24b 6 LPCM 3 FRA 96k 24b 7 LPCM 3 FRA 96k 24b 8 LPCM 3 FRA 96k 24b 9 1 U 0 ON 2 ENG o ON 2 ENG p ON 2 ENG —— A B or Numeric —— AB q A B or Numeric AB —— only] (See pages 14, 15 and 18.) 20 LPCM 3 FRA 96k 24b —— To select the audio mode r 4 —— To show the number of recorded vocals [DVD Karaoke only] (See page 28.) Á1 vocal: ON or “– – –” (OFF) Á2 vocals: V1oV2, V1, V2 or “– – –” (OFF) 1:07:48 —— ÁFor Linear PCM disc: 16 bit to 24 bit m 3 Á“A B” means pressing A/B and “Numeric” means pressing the numeric button. \1The track number cannot be selected during menu play of the Video CD. \2 This function does not work with some DVDs. r s 1 L R PBC OFF Vocal ON Detailed descriptions of each GUI icon A For your reference: ÁFor the language abbreviations used for the audio soundtrack and subtitle language icons, see the table ). ENG English ITA Italian SVE Swedish Screen for player information No. \1 e Remarks To start A-B repeat play (See page 25.) f To select the repeat play mode (See page 24.) ÁC (chapter repeat), T (title repeat) or ÁOFF (normal play) [DVD] ÁT (track repeat), A (disc repeat) or ÁOFF (normal play) [Video CD/CD] g To show the current play mode [Video CD/CD only] (See pages 22 and 23.) Á“– – –” (normal play), PRG (program Áplay) or RND (random play) \1 \1 h * Changing method FRA French DEU German ESP Spanish NLD Dutch NOR Norwegian DAN Danish POR Portuguese RUS Russian JPN Japanese CHI Chinese MAL Malay VIE Vietnamese THA Thai U Others KOR Korean SELECT B AB —— To store a marker SELECT To recall a marker C D>A To clear a marker CD >CLEAR 1 AB 2 T 3 PRG 4 12345 (See page 26.) Á“C D AB” means pressing C/D/A/B. This function does not work with an interactive DVD or dur\1 ing menu play of Video CD. \1 Screen for slow-motion play and rapid advance (reverse) + e Still/Pause Press A to select “O”. f Slow-motion play Press C/D.\ M: Backward [DVD only] L: Forward [DVD/Video CD only] g Play Press B to select “D”. h Rapid reverse/advance Press C (Backward)/D (Forward).\ \ Each time the button is pressed, the speed increases in up to 5 steps. C 2 1 2 4 3 4 21 Program play [Video CD/CD] The player plays the tracks in the disc in an order you specify. 1 Press PLAY MODE in the stop mode. The program playback screen appears on the TV monitor. Choose a track, then press SELECT Track numbers included in the disc 1 7 13 19 2 8 14 20 3 9 15 21 4 10 16 5 11 17 6 12 18 Clear last Clear all Press PLAY to start POWER OPEN/CLOSE 3 */ I @STOP 2 Press C/D/A/B and press SELECT, or press the numeric button(s), to select the preferred track number. H gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G MENU TITLE The selected track is stored in the memory. SELECT Choose a track, then press SELECT 1 7 13 19 2 8 14 20 3 9 15 21 4 10 16 5 11 17 6 12 18 Clear last Clear all Press PLAY to start 2 2 1 2 8 3 5 6 Press PLAY. Play now begins in the programmed sequence. After playback Play is stopped and the program playback screen is displayed. 22 RETURN ANGLE MARKER PLAY MODE A-B Choose a track, then press SELECT 3 AUDIO REPEAT ÁRepeat step 2 to select another track. ÁUp to 18 tracks can be programmed. 1 7 13 19 2 8 14 20 3 9 15 21 4 10 16 5 11 17 6 12 18 Clear last Clear all Press PLAY to start ON SCREEN SUBTITLE CLEAR SET UP DVD 2 Program play [Video CD/CD] A DPLAY Returning to normal play ) 1. Press STOP. (Program play is suspended.) 2. Press PLAY MODE twice. 3. Press PLAY. Normal play begins. (The content of the program is still retained in the memory.) OPEN/CLOSE POWER */ I @STOP H gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G MENU TITLE Clearing the program ) SELECT @STOP When the program playback screen is displayed SELECT Choose a track, then press SELECT 1 7 13 19 2 8 14 20 3 9 15 21 4 10 16 5 11 17 6 12 18 Clear last Clear all Press PLAY to start ON SCREEN SUBTITLE 2 8 3 5 6 AUDIO RETURN ANGLE MARKER PLAY MODE REPEAT A-B PLAY MODE ÁTo clear the last program one by one Move to “Clear last” and press SELECT. (Pressing CLEAR of the remote control unit also clears the last program.) CLEAR SET UP DVD CLEAR ÁTo clear all the programs Move to “Clear all” and press SELECT. (The programs are also cleared when the power is switched to the standby mode or the disc is removed.) Random play [Video CD/CD] * B 2 DPLAY The player plays the tracks in the disc in random order. POWER 1 @STOP OPEN/CLOSE */ I Press PLAY MODE twice in the stop mode. The random playback screen appears on the TV monitor. H gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G MENU TITLE @STOP Random Playback SELECT Press PLAY to start ON SCREEN SUBTITLE AUDIO RETURN ANGLE MARKER 2 PLAY MODE Press PLAY. REPEAT Play now begins in the random order. After playback A-B 1 CLEAR SET UP DVD PLAY MODE Play is stopped and the random playback screen is displayed. Returning to normal play 1. Press STOP. (Random play is suspended.) 2. Press PLAY MODE. 3. Press PLAY. Normal play begins. 23 Repeat play Repeat viewing (listening) Press REPEAT during play. Each time this button is pressed, the TV monitor changes as shown below and the disc will repeat a chapter or title (DVD) or a track (Video CD/CD). ÁDVD Repeat of chapter being played C Repeat of title being played T OPEN/CLOSE POWER */ I @STOP H gSTILL/PAUSE SKIP I SLOW/ F SEARCH G MENU TITLE Cancel repeat mode (Normal play) DPLAY OFF SELECT ON SCREEN SUBTITLE ÁVideo CD/CD Repeat of track being played AUDIO RETURN ANGLE MARKER PLAY MODE T REPEAT A-B CLEAR SET UP DVD REPEAT Repeat of entire disc contents Cancel repeat mode (Normal play) A OFF To return to normal play Press REPEAT several times until “OFF” is displayed. Note: ÁRepeat play works only with discs for which the elapsed playing time appears on the unit’s display during playback. ÁRepeat play may not work correctly with some DVDs. 24 Repeat play A To enjoy program repeat play ) If REPEAT is pressed during program play (see pages 22 and 23), the display changes as follows: OPEN/CLOSE POWER */ I @STOP Repeat of programmed track being played T PRG H gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G MENU TITLE Repeat of all programs A PRG SELECT ON SCREEN SUBTITLE Cancel repeat mode (Normal program play) OFF PRG AUDIO RETURN ANGLE MARKER PLAY MODE REPEAT Repeating sections between two specific points (A-B repeat) * 1 A-B CLEAR SET UP DVD Press A-B during play at the point where repeat play is to commence (A). REPEAT A • 2 Press A-B at the point where repeat play is to be concluded (B). A B B OPEN/CLOSE POWER */ I Repeat play of the selection between points A and B starts. @STOP H To return to normal play gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G MENU TITLE Press A-B several times until “ Á Á” is displayed. SELECT Note: ÁA-B repeat play works only within a title [DVD] or a track [Video CD/CD]. ÁA-B repeat play works only with discs for which the elapsed playing time appears on the unit’s display during playback. ÁSome subtitles recorded around point A or B may fail to appear. [DVD] ON SCREEN SUBTITLE AUDIO RETURN ANGLE MARKER PLAY MODE REPEAT A-B CLEAR SET UP DVD 1· 2 A-B 25 Storing markers in memory to be viewed (listened) again A OPEN/CLOSE POWER */ I Storing a marker in the memory ) 1 @STOP gSTILL/PAUSE DPLAY 2 SELECT Press MARKER during play. H “7” indicates no marker has been stored yet. UUUUU SKIP I SLOW/ F SEARCH G MENU TITLE SELECT 2 ON SCREEN SUBTITLE Press SELECT during play at the starting point to be viewed (listened) again. AUDIO RETURN ANGLE MARKER PLAY MODE Indicates “MARKER 1” is stored in the memory. (If SELECT is pressed where any number is already displayed, the previous starting point will be replaced by the new one.) 1 UUUU REPEAT 1 A-B CLEAR SET UP DVD MARKER Up to 5 markers can be stored in the memory. ÁTo store markers 2 to 5, press +/, to move to “7” and press SELECT. ÁPress MARKER to clear the display. Recalling/clearing a marker 1 Press MARKER during play. * 1234U B OPEN/CLOSE POWER */ I @STOP 2 Press +/, to select the marker to be recalled/cleared. H 1 2 3 4U gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G MENU TITLE SELECT 3 Press ) to recall a marker. or Press CLEAR to clear a marker. ON SCREEN SUBTITLE 2 AUDIO RETURN ANGLE MARKER PLAY MODE REPEAT Play resumes from the point corresponding to the selected marker. (The display will be cleared automatically.) or The selected marker is cleared. (Press MARKER to clear the display.) Note: ÁThese operations work only with discs for which the elapsed playing time appears on the unit’s display during playback. ÁSome subtitles recorded around the marker may fail to appear. [DVD] 26 For your reference: ÁAll the markers are cleared when the unit is switched to the standby mode or the disc tray is opened. 1 MARKER 3 A-B CLEAR SET UP DVD 3 2 Changing subtitle language [DVD only] It is possible to change the subtitle language from the one selected at the initial settings to a different language, if available. (See page 32.) (This operation works only with discs on which multiple subtitle languages are recorded.) 1 Press SUBTITLE during play. ÁWhen no subtitles are recorded, “–” will be displayed instead of the language number. Number of the subtitle language being played back ON 2 ENG 2 SELECT OPEN/CLOSE POWER */ I @STOP I love you H 2 Press )/* until the preferred language is selected. Pressing the numeric button(s) also changes the subtitle language. gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G MENU TITLE ON 1 FRA SELECT ON SCREEN SUBTITLE AUDIO RETURN ANGLE MARKER Je t'aime ÁPress SUBTITLE or SELECT to clear the display. 2 2 PLAY MODE 1 SUBTITLE REPEAT A-B CLEAR SET UP DVD To clear/display the subtitles Press +/, to select ON or OFF at the step 2. Note: ÁIn some cases, the subtitle language is not changed immediately to the selected one. For your reference: ÁWhen the preferred language is not selected even after pressing the button several times, it means that the language is not available on the disc. ÁWhen the unit is switched to the standby mode or the disc tray is opened, subtitles appear in the language selected at the initial settings. If this language is not recorded on the disc, they appear in the disc’s priority language. 27 Changing audio soundtrack language [DVD only] ) A It is possible to change the audio soundtrack language from the one selected at the initial settings to a different language, if available. (See page 32.) (This operation works only with discs on which multiple audio soundtrack languages are recorded.) 1 OPEN/CLOSE POWER */ I @STOP H gSTILL/PAUSE SKIP I SLOW/ F SEARCH G MENU TITLE Press AUDIO during play. AUDIO ÁWhen no audio soundtrack is recorded, “–” will be displayed instead of the language number. Number of the audio soundtrack language being played back DPLAY 2 2 1 SELECT LPCM 1 ENG 96k 24b ON SCREEN SUBTITLE AUDIO RETURN ANGLE 2 MARKER PLAY MODE Hello SELECT REPEAT A-B 2 Press )/* until the preferred language is selected. Pressing the numeric button(s) also changes the audio soundtrack language. CLEAR SET UP DVD LPCM 3 FRA 96k 24b Bon jour ÁPress AUDIO or SELECT to clear the display. For your reference: ÁWhen the preferred language is not selected even after pressing the button several times, it means that language is not available on the disc. ÁWhen the unit is switched to the standby mode or the disc tray is opened, the language heard is the one selected at the initial settings. If this language is not recorded on the disc, only the available language on the disc will be heard. B OPEN/CLOSE POWER */ I @STOP H gSTILL/PAUSE SKIP I 1 U 2 Press +/, until the preferred setting is selected. ÁDVD Karaoke (1 vocal) ON()– – – (OFF) Vocal --- 1 U ÁDVD Karaoke (2 vocals) 1o2>V1>V2>– – – (OFF) ^------------------------------------------} ÁVideo CD LR>L>R ^-------------} L R ÁPress AUDIO or SELECT to clear the display. 28 Note: ÁThis operation does not work with CDs. SLOW/ MENU 1 AUDIO SELECT Press AUDIO during play. Vocal ON 2 F SEARCH G TITLE Switching vocals ON or OFF for Karaoke discs [DVD/Video CD] * 1 DPLAY ON SCREEN SUBTITLE 2 PLAY MODE SELECT REPEAT AUDIO RETURN ANGLE MARKER A-B CLEAR SET UP DVD Viewing from another angle [DVD only] Some DVDs may contain scenes which have been shot simultaneously from a number of different angles. For these discs, the same scene can be viewed from each of these different angles using the ANGLE button. (The recorded angles differ depending on the disc used.) 1 Press ANGLE during play. Number of angle being played back 2 1 Press )/* until the preferred angle is selected. OPEN/CLOSE POWER */ I 5 Pressing the numeric button(s) also changes the angle. @STOP H gSTILL/PAUSE SKIP I DPLAY SELECT SLOW/ F SEARCH G MENU TITLE ÁPress ANGLE or SELECT to clear the display. 1 SELECT Note: ÁThis function only works for discs having scenes recorded at different angles. Á“ANGLE” lights up on the FL display at scenes recorded at different angles to indicate that angle switching is possible. The angle number can be programmed beforehand; the angle will be switched to the selected number when “ANGLE” lights up. ANGLE ON SCREEN SUBTITLE 2 AUDIO RETURN ANGLE MARKER 2 PLAY MODE 2 REPEAT A-B CLEAR SET UP DVD 29 Using a title menu [DVD only] ) A 2 Some discs with movies, for example, may be available with two or more titles. If the disc has a title menu recorded on it, the TITLE button can be used to select the movie title. (The details of operation differ depending on the disc used.) 1 Press TITLE during play. A list of the titles on the disc is now displayed. OPEN/CLOSE POWER */ I @STOP H gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G 2 TITLE MENU MENU TITLE Dogs Castles SELECT Lovers Birds 1 (Example) ÁPressing TITLE again resumes play from the scene when TITLE was first pressed. ON SCREEN SUBTITLE AUDIO RETURN ANGLE 2 TITLE MARKER PLAY MODE 2 REPEAT Press +/,/)/* and press SELECT or PLAY, or press the numeric button(s), to select the preferred title. TITLE MENU Dogs Castles Lovers Birds A-B CLEAR SET UP DVD Birds oftheworld The selected title now starts playing. Using a DVD menu [DVD only] * Some DVDs have unique menu structures called DVD menus. For example, DVDs programmed with complex contents provide guide menus, and those recorded with various languages provide menus for audio and subtitle language. Although the DVD menu’s contents and operation differ from disc to disc, the following explains basic operation when this feature is used. 1 B OPEN/CLOSE POWER */ I @STOP gSTILL/PAUSE DPLAY MENU H SKIP I MENU TITLE DVD MENU The DVD menu available on the 1.SUBTITLE disc is now displayed. 2.AUDIO Press MENU during play. SELECT 3.ANGLE ON SCREEN SUBTITLE AUDIO RETURN ANGLE (Example) ÁPressing MENU again resumes play from the scene when MENU was first pressed. 2 MARKER PLAY MODE REPEAT 2 Press +/,/)/* and press SELECT, or press the numeric button(s), to select the preferred item. DVD MENU 1.SUBTITLE 2.AUDIO 3.ANGLE The selected item is now executed. When the menu continues onto another screen Repeat step 2. 30 1 SLOW/ F SEARCH G A-B CLEAR SET UP DVD 2 Initial settings Once the intial settings have been completed, the player can always be operated under the same conditions (especially with DVD discs). The settings will be retained in the memory even after switching the power to the standby mode until the settings are changed. Common procedures of initial settings 1 Press SET UP in the stop mode. 1 Disc Languages 2 Ratings 3 Menu Language 4 On-Screen Messages 5 FL Display 6 TV Aspect 7 Digital Audio Output 8 Speaker Setting 9 Other Settings 0 Exit Level 8 English On Bright 4:3 OPEN/CLOSE POWER */ I @STOP gSTILL/PAUSE DPLAY SELECT H SKIP I SLOW/ F SEARCH G MENU TITLE 2 2· 3 RETURN Press )/* to select the preferred item and SELECT. SELECT Each screen for setting the value is displayed. ON SCREEN SUBTITLE AUDIO RETURN ANGLE 1 Disc Languages (see page 32) 2 Ratings (see page 33) MARKER 3 Menu Language (see page 34) PLAY MODE 4 On-Screen Messages (see page 35) REPEAT 5 FL Display (see page 35) A-B 6 TV Aspect (see page 36) SET UP CLEAR DVD 7 Digital Audio Output (see page 37) 8 Speaker setting (see page 39) 9 Other Settings (see page 41) 1 SET UP 3 Press )/* to select the preferred value and press SELECT. ÁSome items require additional steps. (See the respective page.) Setting is finished and the initial settings screen is displayed. To cancel during setup operation Press RETURN or select “0”. (The previous screen is displayed.) To clear the initial settings screen Press * to select “0” and press SELECT. (Pressing SET UP or RETURN also clears the initial settings screen.) For your reference: ÁThe numeric buttons can also be used for selecting items or values instead of )/*; in this case, pressing SELECT is not necessary. 31 Initial settings Selecting disc languages [DVD only] This is to select the audio soundtrack language, subtitle language and the language used in title menus or DVD menus which will always be used for every disc to be played back. 1 At the initial settings screen Press )/* to select “1 Disc Languages” and press SELECT. Disc Languages 1 Audio 2 Subtitle 3 Menus English Automatic English */ I @STOP 0 Exit H 2 Press )/* to select the preferred item (1–3) and press SELECT. When “3 Menus” is selected English: English is selected (Factory setting) French/German/Italian/Spanish:\ Each language is selected. Other 7777: Another language can be selected. \German and Italian can be selected only in Continental Europe, United Kingdom and Australia models. 3 Press )/* to select the preferred language at each screen and press SELECT. The screen at the step 1 is displayed. Press * to select “0” and press SELECT to return to the initial settings screen. Note: ÁIf the language selected is not available on the disc, the language designated by each disc will be selected. 32 Also refer to “Common procedures of initial settings” on page 31. SKIP I DPLAY SLOW/ F SEARCH G SELECT MENU TITLE When “1 Audio” is selected English: English is selected (Factory setting) French/German/Italian/Spanish:\ Each language is selected. Original: The original language of each disc will be selected. Other 7777: Another language can be selected. (Refer to the language codes on page 43. Press CLEAR if an incorrect language code is entered.) When “2 Subtitle” is selected Automatic: The same language selected for the “Audio” will be selected. (Factory setting) ÁIf the language selected for the “Audio” is actually used during playback, the subtitles will not appear. ÁIf another language is used during playback, the subtitles will appear in the language selected at the setup “Audio”. English/French/German/Italian/Spanish:\ Each language is selected. Other 7777: Another language can be selected. gSTILL/PAUSE 1 3 ~ OPEN/CLOSE POWER SELECT ON SCREEN SUBTITLE AUDIO RETURN ANGLE MARKER PLAY MODE REPEAT A-B CLEAR SET UP DVD CLEAR 2 Initial settings Selecting rating level [DVD only] This is to disable the playing of specified DVDs which are unsuitable for children. ÁSome DVDs are encoded with specific rating level. If the rating level of the disc is higher than that preset in the setup operation, playback of the disc will be prohibited. 1 At the initial settings screen Press )/* to select “2 Ratings” and press SELECT. DVDs for general audiences/children can be played back. (DVDs for adults are prohibited.) 2 */ I @STOP H DVDs for children can be played back. (DVDs for adults/ general audiences are prohibited.) Playback of all DVDs is prohibited. (e.g. to prohibit playback of DVDs for adults which are not encoded with rating level information) Press )/* to select the preferred level and press SELECT. OPEN/CLOSE POWER gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G 1 4 ~ Please set a rating limit 8 No Limit 7 6 5 4 3 2 1 0 Lock All Press RETURN to cancel All DVDs can be played back. (Factory setting) MENU TITLE SELECT ON SCREEN SUBTITLE AUDIO RETURN ANGLE 3 MARKER PLAY MODE Ratings Enter a 4-digit password, then press SELECT REPEAT A-B CLEAR SET UP DVD U U U U Press RETURN to cancel 3 When level 7 or lower is selected Input a SELECT. 4-digit password The lock symbol appears closed to show the rating is locked. Example: “4343” Do not forget your password. and press Ratings The player is locked. Remember the password. 4 3 4 3 Press SELECT to continue 4 Press SELECT. Setting is finished and the initial settings screen is displayed. ÁThe rating is locked. Any discs whose rating is higher than the setting cannot be played back unless the correct password is entered. Also refer to “Common procedures of initial settings” on page 31. (Continued on the next page) 33 Initial settings A To change the settings ) 1. Press )/* to select “2” at the initial settings screen and press SELECT. OPEN/CLOSE POWER Ratings Enter your 4-digit password, then press SELECT. */ I @STOP H gSTILL/PAUSE SELECT DPLAY SLOW/ F SEARCH G SKIP I U U U U MENU TITLE SELECT Press RETURN to cancel 2. Input a 4-digit password and press SELECT. ON SCREEN SUBTITLE RETURN ANGLE AUDIO Ratings MARKER 1 Unlock Player 2 Change Password 3 Change Level 4 Temporary Unlock PLAY MODE REPEAT A-B CLEAR SET UP DVD 0 Exit 3. Press )/* to select the preferred item (1–4) and press SELECT. ÁPress * to select “0” and press SELECT to exit. (Setting is finished and the initial settings screen is displayed.) 4. When “1 Unlock Player” is selected Press SELECT. When “2 Change Password” is selected Enter a new 4-digit password and press SELECT. Press SELECT again. When “3 Change Level” is selected Select a level and press SELECT. When “4 Temporary Unlock” is selected (The rating is unlocked temporarily only for the current disc.) Press SELECT. Setting is finished and the initial settings screen is displayed. B OPEN/CLOSE POWER */ I @STOP Note: ÁSome discs may not be encoded with specific rating level information though its disc jacket says that it is for “adults”. For those discs, the age restriction will not work. H gSTILL/PAUSE SKIP I At the initial settings screen Press )/* to select “3 Menu Language” and press Select the language SELECT. Factory settings for these Menus. 1 English 2 Français 3 Deutsch 4 Italiano 5 Español Press RETURN to cancel 2 Press )/* to select the preferred language and press SELECT. \ German and Italian can be selected only in Continental Europe, United Kingdom and Australia models. Setting is finished and the initial settings screen is displayed. Also refer to “Common procedures of initial settings” on page 31. 34 SLOW/ F SEARCH G MENU TITLE Selecting language of On-Screen Display menu * 1 DPLAY SELECT ON SCREEN SUBTITLE AUDIO RETURN ANGLE MARKER PLAY MODE REPEAT A-B CLEAR SET UP DVD 1· 2 Initial settings A Switching the On-Screen Display ON or OFF ) OPEN/CLOSE POWER */ I @STOP You can select whether On-Screen Display messages such as PLAY and STOP will be displayed or not. 1 H gSTILL/PAUSE SKIP I SLOW/ F SEARCH G 1· 2 MENU TITLE At the initial settings screen Press )/* to select “4 On-Screen Messages” and press SELECT. SELECT ON SCREEN SUBTITLE On-Screen Messages Factory setting DPLAY AUDIO RETURN ANGLE MARKER 1 On 2 Off PLAY MODE REPEAT A-B Press RETURN to cancel 2 CLEAR SET UP DVD Press )/* to select the preferred item (1 or 2) and press SELECT. Setting is finished and the initial settings screen is displayed. Selecting the display brightness 1 * At the initial settings screen Press )/* to select “5 FL Display” and press SELECT. B OPEN/CLOSE POWER */ I FL Display @STOP Factory setting 1 Bright 2 Dim 3 Dim During DVD/VCD Play(Auto) H gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G 1· 2 MENU TITLE SELECT Press RETURN to cancel ON SCREEN SUBTITLE 2 Press )/* to select the preferred item (1–3) and press SELECT. Setting is finished and the initial settings screen is displayed. AUDIO RETURN ANGLE MARKER PLAY MODE REPEAT A-B CLEAR SET UP For your reference: ÁEven if “3 Dim During DVD/VCD Play (Auto)” is selected, the display resumes brightness when a button for special play such as SLOW/SEARCH and STILL/PAUSE is pressed. DVD Also refer to “Common procedures of initial settings” on page 31. 35 Initial settings Selecting TV screen type Select the appropriate screen type according to your TV set; conventional size screen (4:3) or wide-screen (16:9). 1 At the initial settings screen Press )/* to select “6 TV Aspect” and press SELECT. Select your TV aspect 1 4:3 2 16:9 Press RETURN to cancel POWER OPEN/CLOSE */ I 2 @STOP Press )/* to select the preferred item (1 or 2) and press SELECT. 4:3 Select when a conventional TV set is connected. (factory setting) The video material formatted in the Pan & Scan style is played back in that style (the left and right edges are cut off). The video material not formatted in the Pan & Scan style is played back in the letterbox style (black bands appear at top and bottom of screen). 16:9 Select when a wide-screen TV set is connected. Played in “FULL” size. (Setting the wide-screen TV to “FULL” mode is also necessary.) \ Each screen shows an example when the video material for a wide-screen is played. (This setting does not affect the video material for conventional size.) Setting is finished and the initial settings screen is displayed. Also refer to “Common procedures of initial settings” on page 31. 36 H gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G MENU TITLE SELECT ON SCREEN SUBTITLE AUDIO RETURN ANGLE MARKER PLAY MODE REPEAT A-B CLEAR SET UP DVD 1· 2 Initial settings Selecting digital output Select the digital output to be output from the optical/coaxial digital audio output connector of the unit. 1 At the initial settings screen Press )/* to select “7 Digital Audio Output” and press SELECT. Digital Audio Output 1 LPCM (DVD) Off 2 Dolby Digital Bitstream 3 MPEG PCM OPEN/CLOSE POWER */ I @STOP H 2 Press )/* to select the preferred item (1–3) and press SELECT. When “1 LPCM (DVD)” is selected Off: Only linear PCM of 48 kHz/16 bit is output from the digital audio output connector. During playback of the DVD recorded in the linear PCM of 48 kHz/20 bit/24 bit or 96 kHz, no digital audio is output. (Factory setting) PCM: During playback of the DVD recorded in the linear PCM of 48 kHz/20 bit/24 bit or 96 kHz, digital audio converted to 48 kHz/16 bit is output. (Digital output of PCM audio is restricted to 48 kHz/16 bit or below for copyright protection.) gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G 1 3 ~ 0 Exit MENU TITLE SELECT SELECT ON SCREEN SUBTITLE AUDIO RETURN ANGLE MARKER PLAY MODE REPEAT A-B CLEAR SET UP DVD When “2 Dolby Digital” is selected Bitstream: Dolby Digital (AC-3) bitstream (2ch–5.1ch) is output. (Factory setting) PCM: PCM (2ch) of 48 kHz/16 bit is output. When “3 MPEG” is selected PCM: PCM of 16 bit is output. (Factory setting) Bitstream: Bitstream is output. 3 Press )/* to select the preferred value at each screen and press SELECT. The screen at the step 1 is displayed. Press * to select “0” and press SELECT to return to the initial settings screen. Also refer to “Common procedures of initial settings” on page 31. (Continued on the next page) 37 Initial settings For your reference: ÁMake settings as shown in the table ) depending on the kind of amplifier that is connected to the optical/coaxial digital audio output connector. \ 38 Audio output from the unit’s audio output connectors is converted to 48 kHz/16 bit in addition to audio from the digital audio output connector. To enjoy high quality sound at 48 kHz/20 bit/24 bit or 96 kHz, connect the amplifier or decoder directly to the audio output connectors, not to the digital audio output connector. [Select “Off” at the “1 LPCM (DVD)”.] A Recommendable setting Type of amplifier to be connected LPCM (DVD) Dolby Digital MPEG No amplifier is connected Off Bitstream PCM AV amplifier including Dolby Digital decoder PCM\ Bitstream PCM AV amplifier including Dolby Digital/MPEG audio decoder PCM\ Bitstream Bitstream Initial settings A Speaker setting 1 ) At the initial settings screen POWER Press )/* to select “8 Speaker Setting” and press SELECT. OPEN/CLOSE */ I @STOP Center Center Delay time Large/Small/None Front (L) Large/Small CH. POWER H DPLAY gSTILL/PAUSE SLOW/ F SEARCH G SKIP I TITLE Speaker Setting L 3.9 ms -3 dB C Exit +1 dB Test SL +2 dB 5.3 ms +2 dB R SW SELECT Subwoofer Yes/No ON SCREEN SUBTITLE 1 3 SR 2 3 Surround (L/R) Delay time Surround (R) Large/Small/None ÁUnderlined item is a factory setting. Press +/,/)/* to select the preferred item and press SELECT. RETURN ANGLE AUDIO MARKER ~ Press RETURN to cancel Surround (L) Large/Small/None MENU Front (R) Large/Small PLAY MODE REPEAT A-B CLEAR SET UP DVD Press +/,/)/* to select the preferred value and press SELECT. Speaker icons ÁIf the speaker is connected, display the icon. ÁClear the icon if the speaker is not connected. ÁIf the speaker supports low-frequency (under 100 Hz) reproduction, select the larger icon. If the speaker’s low-frequency (under 100 Hz) reproduction ability is poor, select the smaller icon. [When the subwoofer is not connected, be sure to select “Large” for the front speakers (L/R).] Delay time: If the surround speakers or the center speaker can’t be installed at an equal distance to (or further away) the front speakers from the listening position, change the delay time to get better surround effect. ÁWhen D2 or D3 is equal to or larger than D1, no setting is necessary (*). Otherwise, change the setting according to the table below. B Center speaker Front speaker (L) C L Speaker Delay time Difference between D1 and D2/D3 Center speaker (D2) 1.3 ms 2.6 ms 3.9 ms 5.3 ms approx. 150 cm approx. 100 cm approx. 150 cm approx. 200 cm 5.3 ms 10.6 ms 15.9 ms approx. 200 cm approx. 400 cm approx. 600 cm Surround speakers (D3) R D2 D1 D3 SL Front speaker (R) D1 SW Subwoofer D3 SR Surround speaker (L) Surround speaker (R) Channel balance: While listening to the test signal, adjust the volume of the center, surround (L), surround (R) speakers and the subwoofer so that the volume is equal to that of the front speakers. (Continued on the next page) 39 Initial settings 4 Press +/,/)/* to select “Exit” and press SELECT. Setting is finished and the initial settings screen is displayed. Note: ÁThe “Large/Small” setting has no effect on DVDs recorded in MPEG 2 audio. For your reference: ÁTo output the test signal 1. Press +/,/)/* to select “Test”, and then press SELECT. (Test signals will be output consecutively from each speaker clockwise.) 2. Press +/,/)/* to select the appropriate volume (p6 dB through o6 dB) while the test signal is being output from the speaker. 3. Press SELECT. (The test signals are stopped.) POWER OPEN/CLOSE */ I @STOP H Also refer to “Common procedures of initial settings” on page 31. gSTILL/PAUSE SKIP I DPLAY SLOW/ F SEARCH G MENU TITLE SELECT ON SCREEN SUBTITLE 4 AUDIO RETURN ANGLE MARKER PLAY MODE REPEAT SELECT A-B CLEAR SET UP DVD 40 Initial settings Other settings 1 At the initial settings screen Press )/* to select “9 Other Settings” and press SELECT. Other Settings 1 Still Mode 2 Audio during Search 3 TV Mode (4:3) 4 D. Range Compression Automatic On Pan&Scan Off 0 Exit OPEN/CLOSE POWER Press )/* to select the preferred item (1–4) and press SELECT. When “1 Still Mode” is selected Automatic: “Frame still” and “Field still” are automatically selected during the still mode. (Factory setting) Field: Select this setting when jittering occurs in the pictures even when “Automatic” is selected. When “2 Audio during Search” is selected On: Factory setting (When noises during search are disOn: agreeable, select “Off”.) Off: Select this setting if audio during search is not necessary. @STOP H SKIP I DPLAY SLOW/ F SEARCH G 1 3 MENU TITLE SELECT SELECT ON SCREEN SUBTITLE AUDIO RETURN ANGLE MARKER PLAY MODE REPEAT A-B When “3 TV Mode (4:3)” is selected Pan & Scan: The video material for a wide-screen will be played back in the Pan & Scan style on a conventional size TV. (Factory setting) ÁVideo material not formatted in the Pan & Scan style will be played back in the letterbox style. (See page 36.) Letterbox: Select this setting to play back the video material for a wide-screen in the letterbox style on a conventional size TV. gSTILL/PAUSE ~ 2 */ I CLEAR SET UP DVD When “4 D. (Dynamic) Range Compression” is selected Off: Normal audio range is selected. (Factory setting) On: Select this setting to enjoy listening to dynamic sound even on a low volume. This is useful for latenight listening. [This function only works with Dolby Digital (AC-3) DVDs.] 3 Press )/* to select the preferred value at each screen and press SELECT. The screen at the step 1 is displayed. Press )/* to select “0” and press SELECT to return to the initial settings screen. Also refer to “Common procedures of initial settings” on page 31. 41 Disc handling and maintenance A Handling precautions ÁHold the disc by the edges so the surface will not be soiled with fingerprints. ()) Fingerprints, dirt and scratches can cause skipping and distortion. ÁDo not write on the label side with a ball-point pen or other writing utensils. ÁDo not use record cleaning sprays, benzine, thinner, static electricity prevention liquids or any other solvent. ÁBe careful not to drop or bend the disc. ÁDo not install more than 1 disc on the disc tray. ÁDo not try to close the disc tray when the disc is not installed properly. (*) ÁBe sure to store the disc in its exclusive case when not in use. If the surface is soiled + Wipe gently with a soft, damp (water only) cloth. When wiping discs, always move the cloth from the center hole toward the outer edge. (If you wipe the discs using a circular motion, circular scratches are likely to occur, which will cause noise.) B If the disc is brought from a cold to a warm environment, moisture may form on the disc Wipe this moisture off with a soft, dry, lint-free cloth before using the disc. Improper disc storage You can damage discs if you store them in the following places: ÁAreas exposed to direct sunlight ÁHumid or dusty areas ÁAreas directly exposed to a heat outlet or heating appliance Disc tray Discs which cannot be played with this player For Continental Europe and United Kingdom models ÁDVD with Region No. other than “2” or “ALL” For Australia model ÁDVD with Region No. other than “4” or “ALL” For other models ÁDVD with Region No. other than “3” or “ALL” ÁDVD-ROM ÁDVD-R/DVD-RAM ÁCD-ROM ÁCDV ÁCD-G ÁDo not try to play Photo CD or CD-R. To prevent a malfunction of this unit ÁDo not use any non standard shaped CD (heart etc.) available on the market, because it may damage the unit. ÁDo not use a CD with tape, seals, or paste on it, because damage to the unit may result. Maintenance 42 ÁBe sure to switch the power to the standby mode and disconnect the AC mains lead before maintaining the unit. ÁWipe this unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth which has been dipped in a weak soap-and-water solution and wrung out thoroughly, and then wipe again with a dry cloth. ÁNever use alcohol, benzine, thinner, cleaning fluid or other chemicals. And do not use compressed air to remove dust. C Disc Language code list Enter the appropriate code number for the initial settings “Audio”, “Subtitle” and/or “Menus” (see page 32). Code Language Name Code Language Name Code Language Name Code Language Name 6565 Afar 7079 Faroese 7678 Lingala 8375 Slovak 6566 Abkhazian 7082 French 7679 Laothian 8376 Slovenian 6570 Afrikaans 7089 Frisian 7684 Lithuanian 8377 Samoan 6577 Ameharic 7165 Irish 7686 Latvian, Lettish 8378 Shona 6582 Arabic 7168 Scots Gaelic 7771 Malagasy 8379 Somali 6583 Assamese 7176 Galician 7773 Maori 8381 Albanian 6588 Aymara 7178 Guarani 7775 Macedonian 8382 Serbian 6590 Azerbaijani 7185 Gujarati 7776 Malayalam 8385 Sundanese 6665 Bashkir 7265 Hausa 7778 Mongolian 8386 Swedish 6669 Byelorussian 7273 Hindi 7779 Moldavian 8387 Swahili 6671 Bulgarian 7282 Croatian 7782 Marathi 8465 Tamil 6672 Bihari 7285 Hungarian 7783 Malay 8469 Telugu 6678 Bengali; Bangla 7289 Armenian 7784 Maltese 8471 Tajik 6679 Tibetan 7365 Interlingua 7789 Burmese 8472 Thai 6682 Breton 7378 Indonesian 7865 Nauru 8473 Tigrinya 6765 Catalan 7383 Icelandic 7869 Nepali 8475 Turkmen 6779 Corsican 7384 Italian 7876 Dutch 8476 Tagalog 6783 Czech 7387 Hebrew 7879 Norwegian 8479 Tonga 6789 Welsh 7465 Japanese 7982 Oriya 8482 Turkish 6865 Danish 7473 Yiddish 8065 Panjabi 8484 Tatar 6869 German 7487 Javanese 8076 Polish 8487 Twi 6890 Bhutani 7565 Georgian 8083 Pashto, Pushto 8575 Ukrainian 6976 Greek 7575 Kazakh 8084 Portuguese 8582 Urdu 6978 English 7576 Greenlandic 8185 Quechua 8590 Uzbek 6979 Esperanto 7577 Cambodian 8277 Rhaeto-Romance 8673 Vietnamese 6983 Spanish 7578 Kannada 8279 Romanian 8679 Volapük 6984 Estonian 7579 Korean 8285 Russian 8779 Wolof 6985 Basque 7583 Kashmiri 8365 Sanskrit 8872 Xhosa 7065 Persian 7585 Kurdish 8368 Sindhi 8979 Yoruba 7073 Finnish 7589 Kirghiz 8372 Serbo-Croatian 9072 Chinese 7074 Fiji 7665 Latin 8373 Singhalese 9085 Zulu 43 Troubleshooting If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. Symptom (Common) No power. Insert the AC mains lead securely into the power outlet. Power is automatically switched to the standby mode. The power is automatically switched to the standby mode after approx. 30 minutes have elapsed in the stop mode (auto turn-off function). Turn the power back on. ÁPlay fails to start even when PLAY is pressed. ÁPlay commences but then stops immediately. ÁCondensation has formed: wait about 1 to 2 hours to allow the player to dry out. ÁThis player cannot play discs other than DVDs, Video CDs and CDs. ÁThe disc may be dirty and may require cleaning. ÁEnsure that the disc is installed with the label side up. No picture. ÁEnsure that the equipment is connected properly. ÁEnsure that the input setting for the TV is an Audio/Video (AV) position, e.g. AV1, AV2. ÁNo sound. ÁDistorted sound. ÁEnsure that the equipment is connected properly. ÁEnsure that the input settings for the TV and stereo system are proper. Picture is distorted during rapid advance or rapid reverse. The picture will be somewhat distorted at times: this is normal. No rapid advance (or rapid reverse) play. Some discs may have sections which prohibit rapid advance (or rapid reverse). No 4:3 (16:9) picture. Choose the correct setup “TV Aspect” item which matches the TV set used. No on-screen display. The “Off” setting is selected for “On-Screen Messages”: select “On”. No surround sound. Choose the correct setup at the “Speaker setting” which matches your stereo system. No operations can be performed with the remote control. ÁCheck the batteries are installed with the correct polarities (o and p). ÁThe batteries are depleted: replace them with new ones. ÁPoint the remote control unit at the remote control sensor and operate. ÁOperate the remote control unit at a distance of not more than 7 meters from the remote control sensor. ÁRemove the obstacles between the remote control unit and remote control sensor. No key operation (by the unit and/or the remote control) is effective. Switch the power to the standby mode and then return to ON. Alternatively, switch the power to the standby mode, disconnect the AC mains lead and then re-connect it. (The player may not be operating properly due to lightning, static electricity or some other external factor.) GUI Screen not displayed or only partially displayed on the TV Screen. Select the appropriate TV screen type by consulting the operation manual of the TV. Symptom [DVD] Remedy Play does not commence even when title is selected. 44 Remedy Confirm the “Ratings” setting. Symptom [DVD] Remedy Audio soundtrack and/or subtitle language is not the one selected at the initial settings. If the audio soundtrack and/or subtitle language does not exist on the disc, the language selected at the initial settings will not be seen/heard. The menu is displayed in French (example). The setup “Menus” of “Disc Languages” is set to French: select English. Lightening and darkening of the picture. Some discs will be copy protected at the direction of copyright owners. During playback of those discs, picture may not be normally played back when video signals containing a copy protected signal are played back through a VCR. It is recommended to connect the DVD/Video CD/CD player directly to an AV amplifier or to a TV set, not through a VCR. No subtitles. ÁSubtitles appear only with discs which contain them. ÁSubtitles are cleared from the TV monitor. Perform the steps on page 27 to display the subtitles. Alternative audio soundtrack (or subtitle) languages fail to be selected. ÁAn alternative language is not selected with discs which do not contain more than one language. ÁIn the case of some discs, the alternative language cannot be selected by operating the AUDIO or SUBTITLE button. Try selecting it from the DVD menu if one is available. Angle cannot be changed. This function is dependent on software availability. Even if a disc has a number of angles recorded, these angles may be recorded for specific scenes only (when “ANGLE” lights up on the FL display.) The password for age restriction has been forgotten. While the unit is in the stop mode, hold the unit’s 0SKIP button and the STILL/ PAUSE button down simultaneously and then hold the POWER button down for longer than 3 seconds (until “Initialized” disappears from the TV monitor). The lock will be released and all initial settings will return to the default values. Symptom [Video CD] No menu play. Remedy This function works only for Video CDs with playback control. Self-diagnosis display function When an error or trouble is detected during operation, a service number appears in the display window. When a service number has appeared, check out the details given below. Service number U11 HÅÅ Player status Remedy Disc is dirty. Wipe the disc clean. Trouble is likely to have occurred. The number following “H” differs depending on the status of the player. Switch the power to the standby mode and then return to ON. Alternatively, switch the power to the standby mode, disconnect the AC mains lead and then re-connect it. If the service number fails to be cleared even when the remedial action is taken, ask for the service engineer to repair the player. 45 Definition of terms Angle Recorded onto some DVD discs are scenes which have been simultaneously shot from a number of different angles (the same scene is shot from the front, from the left side, from the right side, etc.). With such discs, the ANGLE button can be used to view the scene from different angles. Chapter number These numbers are recorded on DVD discs. A title is subdivided into many sections, each of which is numbered, and specific parts of video presentations can be searched quickly using these numbers. DVD This refers to a high-density optical disc on which high-quality pictures and sound have been recorded by means of digital signals. Incorporating a new video compression technology (MPEG II) and high-density recording technology, DVD enables esthetically pleasing full-motion video to be recorded over long periods of time (for instance, a whole movie can be recorded). DVD has a structure consisting of two 0.6 mm thin discs which are adhered to each other. Since the thinner the disc, the higher the density at which the information can be recorded, a DVD disc has a greater capacity than a single 1.2 mm thick disc. Since the two thin discs are adhered to each other, there is the potential to achieve double-sided play sometime in the future for even longer duration play. Playback control This is recorded on a Video CD (version 2.0). The scenes or information to be viewed (or listened to) can be selected interactively with the TV monitor by looking at the menu shown on the TV monitor. Subtitles These are the printed lines appearing at the bottom of the screen which translate or transcribe the dialogue. They are recorded on DVD discs. Time number This indicates the play time which has elapsed from the start of a disc or a title. It can be used to find a specific scene quickly. (It may not work with some discs.) Title number These numbers are recorded on DVD discs. When a disc contains two or more movies, these movies are numbered as title 1, title 2, etc. Track number These numbers are assigned to the tracks which are recorded on Video CDs and CDs. They enable specific tracks to be located quickly. Video CD This contains recordings of pictures and sound whose quality is on a par with that of videotape. This player also supports Video CDs with playback control (version 2.0). 46 Specifications Power requirements: Signal system: For Continental Europe, United Kindom and Australia models AC 220–240 V, 50 Hz For other models AC 110–240 V, 50/60 Hz For Continental Europe, United Kingdom and Australia models PAL 625/50, PAL 525/60 For other models NTSC/PAL Weight: 3.6 kC Dimensions: 435 (W)q284 (D)q87.5 (H) mm (excluding protrusions) Operating temperature range: o5 to o35uC Operating humidity range: 5 to 90% (no condensation) Discs played: (1) DVD-VIDEO disc 12 cm single-sided, single-layer 12 cm single-sided, double-layer 12 cm double-sided, double-layer (one layer per side) 8 cm single-sided, single-layer 8 cm single-sided, double-layer 8 cm double-sided, double-layer (one layer per side) (2) Compact disc (CD-DA, VIDEO CD) 12 cm disc 8 cm disc S-video output: Y output level: 1 Vp-p (75°) C output level: 0.300 Vp-p (75°) Output connector: S terminal (1 system) Video output: Output level: 1 Vp-p (75°) Output connector: Pin jack (2 systems) Power consumption: 22 W (approx. 4 W when set to standby mode by the STANDBY/ ON button or the remote control) Audio output: Output level: 2 Vrms (1 kHz, 0 dB) Output connector: Pin jack 5.1ch mixed output: 1 system (2ch) 5.1ch discrete output: 1 system (5.1ch) Audio signal output characteristics: (1) Frequency response: ÁDVD (linear audio): Á2 Hz–22 kHz (48 kHz sampling) Á2 Hz–44 kHz (96 kHz sampling) ÁCD audio: 2 Hz–20 kHz (EIAJ) (2) S/N ratio: ÁCD audio: 115 dB (EIAJ) (3) Dynamic range: ÁDVD (linear audio): 102 dB ÁCD audio: 99 dB (EIAJ) (4) Total harmonic distortion: ÁCD audio: 0.0025% (EIAJ) Digital audio output: Optical digital output: Optical connector Coaxial digital output: pin jack Pickup: Wave length: 655 nm Laser power: CLASS 2 Specifications are subject to change without notice. Weight and dimensions are approximate. 47 Region Management Information Region Management Information: This DVD/VIDEO CD/CD player is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this DVD/VIDEO CD/CD player, this DVD/VIDEO CD/CD player cannot play this disc. For Continental Europe and United Kingdom models The Region number for this DVD/VIDEO CD/CD player is 2. For Australia model The Region number for this DVD/VIDEO CD/CD player is 4. For other models The Region number for this DVD/VIDEO CD/CD player is 3. 2 3 4 This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. PA PARIS-EST RUE AMBROISE CROIZAT CROISSY-BEAUBOURG BP70-77312 MARNE LAVALLEE, CEDEX 2 FRANCE YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA VQT7523-1 Printed in Japan
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Yamaha DVD-S700 Manual de usuario

Categoría
Reproductores de DVD
Tipo
Manual de usuario