Yamaha DME8o-ES El manual del propietario

Categoría
Sintetizador
Tipo
El manual del propietario

Este manual también es adecuado para

EN
Owners Manual
DIGITAL MIXING ENGINE SATELLITE
The above warning is located on the top of the unit.
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to alert
the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand,
tripod, bracket, or table specified
by the manufacturer, or sold with
the apparatus. When a cart is
used, use caution when moving
the cart/apparatus combination
to avoid injury from tip-over.
13 Unplug this apparatus during
lightning storms or when unused for long periods of
time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
(98-6500)
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (Perchlorate)
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
This product contains a battery that contains perchlorate material.
Perchlorate Material—special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions con-
tained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by
the FCC, to use the product.
2. IMPORTANT:
When connecting this product to accessories and/
or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE:
This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital
devices. Compliance with these requirements provides a reason-
able level of assurance that your use of this product in a residential
environment will not result in harmful interference with other elec-
tronic devices. This equipment generates/uses radio frequencies
and, if not installed and used according to the instructions found in
the users manual, may cause interference harmful to the operation
of other electronic devices. Compliance with FCC regulations does
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)
not guarantee that interference will not occur in all installations. If
this product is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try to elimi-
nate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by
the interference.
Utilize power outlets that are on different branch (circuit breaker or
fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type of
product. If you can not locate the appropriate retailer, please con-
tact Yamaha Corporation of America, Electronic Service Division,
6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
FCC INFORMATION (U.S.A.)
* This applies only to products distributed by
YAMAHA CORPORATION OF AMERICA.
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif.
90620
Telephone : 714-522-9011
Type of Equipment : DIGITAL MIXING ENGINE SATELLITE
Model Name : DME8i-ES/DME8o-ES/DME4io-ES
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including inter-
ference that may cause undesired operation.
See user manual instructions if interference to radio reception is
suspected.
(FCC DoC)
ADVARSEL!
Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskift-
ning må kun ske med batteri af samme fabrikat og type. Levér det
brugte batteri tilbage til leverandoren.
VARNING
Explosionsfara vid felaktigt batteribyte. Använd samma batterityp
eller en ekvivalent typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens instruktion.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda
paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä
käytetty paristo valmistajan ohjeiden mukaisesti.
(lithium caution)
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
WARNING:
THIS APPARATUS MUST BE EARTHED
IMPORTANT. The wires in this mains lead are coloured in accor-
dance with the following code:
GREEN-AND-YELLOW : EARTH
BLUE : NEUTRAL
BROWN : LIVE
As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured markings identifying the terminals
in your plug proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be con-
nected to the terminal in the plug which is marked by the letter E or
by the safety earth symbol or colored GREEN or GREEN-and-
YELLOW.
The wire which is coloured BLUE must be connected to the termi-
nal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the ter-
minal which is marked with the letter L or coloured RED.
This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.(3 wires)
NEDERLAND / THE NETHERLANDS
Dit apparaat bevat een lithium batterij voor geheugen back-up.
This apparatus contains a lithium battery for memory back-up.
Raadpleeg uw leverancier over de verwijdering van de batterij op
het moment dat u het apparaat ann het einde van de levensduur of
gelieve dan contact op te nemen met de vertegenwoordiging van
Yamaha in uw land.
•For the removal of the battery at the moment of the disposal at the
end of life please consult your retailer or Yamaha representative
office in your country.
Gooi de batterij niet weg, maar lever hem in als KCA.
Do not throw away the battery. Instead, hand it in as small chemical
waste.
(lithium disposal)
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
4
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Only use the voltage specified as correct for the device. The required voltage is
printed on the name plate of the device.
Use only the included power cord.
If you intend to use the device in an area other than in the one you purchased,
the included power cord may not be compatible. Please check with your Yamaha
dealer.
Do not place the power cord near heat sources such as heaters or radiators, and
do not excessively bend or otherwise damage the cord, place heavy objects on
it, or place it in a position where anyone could walk on, trip over, or roll anything
over it.
Be sure to connect to an appropriate outlet with a protective grounding
connection. Improper grounding can result in electrical shock.
Do not open the device or attempt to disassemble the internal parts or modify
them in any way. The device contains no user-serviceable parts. If it should
appear to be malfunctioning, discontinue use immediately and have it inspected
by qualified Yamaha service personnel.
Do not expose the device to rain, use it near water or in damp or wet conditions,
or place containers on it containing liquids which might spill into any openings.
Never insert or remove an electric plug with wet hands.
If the power cord or plug becomes frayed or damaged, or if there is a sudden
loss of sound during use of the device, or if any unusual smells or smoke
should appear to be caused by it, immediately turn off the power switch,
disconnect the electric plug from the outlet, and have the device inspected by
qualified Yamaha service personnel.
If this device should be dropped or damaged, immediately turn off the power
switch, disconnect the electric plug from the outlet, and have the device
inspected by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the device or other property. These precautions include, but are not limited to, the following:
Remove the electric plug from the outlet when the device is not to be used for
extended periods of time, or during electrical storms.
When removing the electric plug from the device or an outlet, always hold the
plug itself and not the cord. Pulling by the cord can damage it.
Before moving the device, remove all connected cables.
When setting up the device, make sure that the AC outlet you are using is easily
accessible. If some trouble or malfunction occurs, immediately turn off the
power switch and disconnect the plug from the outlet. Even when the power
switch is turned off, electricity is still flowing to the product all the minimum
level. When you are not using the product for a long time, make sure to unplug
the power cord from the wall AC outlet.
If this device is to be mounted in an EIA-standard rack, leave the back of the rack
open and make sure that it is at least 10 cm away from walls or surfaces. Also, if
this device is to be mounted with devices that tend to generate heat, such as
power amplifiers, be sure to keep an adequate gap between this device and the
heat-generating devices or install ventilation panels to prevent high
temperatures from developing inside this device.
Inadequate ventilation can result in overheating, possibly causing damage to the
device(s), or even fire.
If several of the devices are mounted in an EIA-compliant rack, carefully read the
section “Precautions for Using a Rack-mounted DME Satellite” on page 17
•Avoid setting all equalizer controls and faders to their maximum. Depending on
the condition of the connected devices, doing so may cause feedback and may
damage the speakers.
Do not expose the device to excessive dust or vibrations, or extreme cold or heat
(such as in direct sunlight, near a heater, or in a car during the day) to prevent
the possibility of panel disfiguration or damage to the internal components.
Do not place the device in an unstable position where it might accidentally fall
over.
Do not block the vents. This device has ventilation holes at the rear to prevent
the internal temperature from becoming too high. In particular, do not place the
device on its side or upside down. Inadequate ventilation can result in
overheating, possibly causing damage to the device(s), or even fire.
Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile
phone, or other electric devices. Doing so may result in noise, both in the device
itself and in the TV or radio next to it.
Power supply/Power cord
Do not open
Water warning
If you notice any abnormality
Power supply/Power cord
Location
(5)-4
1/2
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
5
Before connecting the device to other devices, turn off the power for all devices.
Before turning the power on or off for all devices, set all volume levels to
minimum.
Do not insert your fingers or hands in any gaps or openings on the device.
Condensation can occur in the device due to rapid, drastic changes in ambient
temperature—when the device is moved from one location to another, or air
conditioning is turned on or off, for example. Using the device while
condensation is present can cause damage. If there is reason to believe that
condensation might have occurred, leave the device for several hours without
turning on the power until the condensation has completely dried out.
•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any
gaps or openings on the device. If this happens, turn off the power immediately
and unplug the power cord from the AC outlet. Then have the device inspected
by qualified Yamaha service personnel.
Do not use the device for a long period of time at a high or uncomfortable
volume level, since this can cause permanent hearing loss. If you experience
any hearing loss or ringing in the ears, consult a physician.
Do not rest your weight on the device or place heavy objects on it, and avoid use
excessive force on the buttons, switches or connectors.
This device has a built-in backup battery that maintains data in internal memory
even when the device’s power is switched off. The backup battery will eventually
become depleted, however, and when that happens the contents of the internal
memory will be lost.* To prevent loss of data be sure to replace the backup
battery before it becomes fully depleted. When the backup battery charge
becomes low, the [ERROR] indicator on the front panel blinks (For details, refer
to “Error Messages” on page 38).
In this case, do not turn off the power and immediately transfer any data you
want to save to a computer or other external storage device, then have qualified
Yamaha service personnel replace the backup battery. The average life of the
internal backup battery is approximately 5 years, depending on operating
conditions.
* Data items maintained in the internal memory by the backup battery are as
follows:
• Current scene parameters and number.
• Device parameters (HA, UTILITY, Master Mute/Level, etc.).
• Event log.
Data items other than those described above are stored in memory that does not
require backup power, and will be retained even if the backup battery fails.
Do not turn the [POWER] switch on and off repeatedly and rapidly. Be sure to wait six seconds or more between turning the power to the unit off and then on.
The rubber feet included in this package can be attached to the speaker to prevent slippage when it is to be used on a slippery surface.
Always turn the power off when the device is not in use.
The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualified Yamaha service
personnel about replacing defective components.
Connections
Handling caution
Backup battery
Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.
Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal use.
The illustrations in this owner’s manual are for instructional purposes, and may appear somewhat different from the actual equipment.
EtherSound is a trademark of Digigram SA.
Ethernet is a trademark of Xerox Corporation.
All other trademarks are the property of their respective holders and are hereby acknowledged.
(5)-4
2/2
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
6
Foreword .......................................... 7
Accessories (Please make sure the following items are
included in the package.)................................ 7
Options........................................................................... 7
About the Product Names............................................... 7
About the Firmware Version ........................................... 7
Preparation...................................................................... 7
Connecting the AC power cord........................................... 7
Turning the power on and off ............................................. 7
Introduction to the DME Satellite .............. 8
Differences between DME8i-ES, DME8o-ES,
and DME4io-ES ............................................ 8
DME Satellite Features ................................................... 8
Audio System Network ................................................... 9
Glossary for the DME Satellite........................................ 9
Signal Types.................................................................. 11
System Examples........................................................... 12
About DME Designer................................................... 13
Controls and Connectors ....................... 14
Front Panel ................................................................... 14
Caution when turning the power off ............................. 15
Rear Panel..................................................................... 16
Precautions for Using a Rack-mounted DME Satellite.. 17
Connecting to a Computer ..................... 18
USB Connection........................................................... 18
Network Settings............................................................... 19
Ethernet Connection ([NETWORK] Connector)......... 20
Audio I/O Connection ........................... 24
Digital Audio Connection (EtherSound Connectors).... 24
Analog Audio Connection ([INPUT] & [OUTPUT]
Connectors) ................................................. 25
Connecting to an External Device............. 26
Remote Connection ([REMOTE] Connector).............. 26
Controlling external head amplifiers from the DME
Satellite ................................................................. 26
Controlling a DME Satellite’s internal head amps from a
digital mixer .......................................................... 27
Controlling the DME Satellite from an external device...... 27
EtherSound Connection (EtherSound Connectors)....... 28
Controlling DME Satellite’s internal head amps from a
digital mixer .......................................................... 28
Network Connection ([NETWORK] Connectors) ....... 29
GPI Connection ([GPI] Connector).............................. 30
Other Functions.................................. 31
Initializing the DME Satellite........................................ 31
References ....................................... 32
Options ......................................................................... 32
ICP1.................................................................................. 32
CP4SW, CP4SF, and CP1SF............................................. 32
Troubleshooting............................................................ 33
Component................................................................... 33
MIDI Data Format ....................................................... 34
1. MIDI functions on the DME8i-ES, DME8o-ES,
and DME4io-ES ................................................... 34
2. MIDI Data Flow ........................................................... 34
3. MIDI Setup................................................................... 34
4. MIDI Format ................................................................ 35
MIDI Implementation Chart ........................................ 37
Display Messages........................................................... 38
Error Messages................................................................... 38
Warning Messages ............................................................. 38
General Specifications ................................................... 39
Electrical Characteristics................................................ 39
Input/Output Characteristics ........................................ 42
[NETWORK] Connector (100Base-TX Ethernet,
RJ-45) .......................................................... 43
Dimensions ................................................................... 44
Index ............................................................................. 45
Contents
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
7
Thank you for choosing a Yamaha DME8i-ES/DME8o-ES/DME4io-ES Digital Mixing Engine Satellite.
In order to take full advantage of the features and performance provided by the DME8i-ES/DME8o-ES/DME4io-ES, we urge
you to read this owner’s manual thoroughly before connecting or using the unit. Keep this manual in a safe place for future ref-
erence.
Accessories (Please make
sure the following items are
included in the package.)
DME8i-ES/DME8o-ES/DME4io-ES Owner’s
Manual (this document)
•AC power cord
•Euroblock plug (16P) x 1
•Euroblock plug (3P) x 8
•Rubber feet x 4
Options
Control Panels
ICP1 Intelligent Control Panel
CP4SW Control Panel
CP4SF Control Panel
CP1SF Control Panel
About the Product Names
In this manual, models DME8i-ES, DME8o-ES, and
DME4io-ES are all called “DME Satellite,” and models
DME64N and DME24N, DME8i-C/DME8o-C/
DME4io-C and the DME Satellite are categorized as the
DME series.
About the Firmware Version
You can check the version number of the DME Satellite
firmware by using the DME Designer application software.
You can also download the latest firmware from the follow-
ing Yamaha website.
http://www.yamahaproaudio.com/downloads/
Preparation
Connecting the AC power cord
First plug the female-connector end of the AC cord into the
[AC IN] socket on the rear panel of the DME Satellite, then
plug the male plug into an appropriate AC mains outlet.
Be sure to use the voltage specified for the device.
Turning the power on and off
1.
Press the [POWER] switch to turn on the
power to the DME Satellite.
2.
Press the [POWER] switch again to turn off
the power.
Foreword
NOTE
For more information on your Control Panel, refer to the owners
manual that came with the Control Panel, as well as the DME
Designer Owner’s Manual.
Be sure to turn all devices OFF before connecting AC
mains power.
To prevent the initial power-on surge from generating a
large noise spike or damaging your speaker system, turn
the devices on in the following order: audio sources, mixer
(such as M7CL or PM5D), DME Satellite, and finally
power amplifiers.
Reverse this order when turning power off.
NOTE
The DME Satellite remembers scene settings when you turn off
the power.
When you turn on the power to the DME Satellite, it will start up
with the same scene settings.
You can use the “Last Mem. Resume” setting in DME Designer
to set up the DME Satellite so that at the startup it will recall the
scene selected before you turned off the power to the device.
•Do NOT turn off the power to the DME Satellite while
it is receiving data from DME Designer or while it is
being manipulated from an external device. Otherwise,
a malfunction may occur.
•Even when the power switch is turned off, electricity is
still flowing to the product all the minimum level.
When you are not using the product for a long time,
make sure to unplug the power cord from the wall AC
outlet.
CAUTION
CAUTION
CAUTION
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
8
Differences between DME8i-ES, DME8o-ES, and DME4io-ES
The differences between these three models are as follows:
DME8i-ES
This model features 8-channel analog inputs.
DME8o-ES
This model features 8-channel analog outputs.
DME4io-ES
This model features 4-channel analog inputs and 4-channel analog outputs.
DME Satellite Features
In addition to basic mixing and matrix output functions, the DME Satellite includes a equalizers, compressors,
delay, etc. – that can be patched together via DME Designer to configure just about any audio system you need.
The EtherSound connectors on the device enable you to remotely control analog inputs and outputs by transfer-
ring digital audio signals via a network.
The following steps summarize the process for setting up the DME Satellite for use:
(For details, refer to the “DME Setup Manual”.)
1.
Install USB-MIDI Driver, DME Designer and DME-N Network Driver.
2.
Set up the network from DME Designer (page 19).
3.
Connect devices.
Network connection
Ethernet connection (page 20)
USB connection (page 18)
EtherSound connection (page 28)
In order to route inputs and outputs, you’ll need the “AVS-ESMonitor” application software made by the
AuviTran SARL.
You can download this from the following website.
http://www.auvitran.com/view.php?products_AVS-ESMonitor.php
Analog connection (page 25)
External device connection
Remote connection (page 26)
GPI connection (page 30)
4.
Make network settings on your computer.
5.
Create a configuration using DME Designer, then transfer it to the DME Satellite.
Introduction to the DME Satellite
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
Introduction to the DME Satellite
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
9
Audio System Network
Multiple DME series units that are interconnected in a network via Ethernet function as a single audio system.
In a DME audio system, a group of the same models that can be operated in sync is called a “device group;” audio
processing divisions that accommodate multiple device groups are called “zones;” and the entire area serviced by
the acoustic system is called an “area.”
Each device group always includes one DME series unit that functions as the “group master” and controls all other
DME series units in the same device group.
If a computer is connected to the network, you can use the computer to control an entire device group via the
group master.
Glossary for the DME Satellite
This section explains terminology specific to the DME Satellite.
Components and parameters
The individual audio processing modules (equalizers, compressors, etc.) are called “components.”
External head amplifier control modules are also available as components.
Changing the parameters of components enables control over the operation of the components.
Configuration
A “configuration” is a complete set of components for constructing an audio system.
Each configuration determines the audio function(s) of the corresponding DME Satellite unit.
All parameter sets included with each component in a configuration are called “preset parameters.”
One DME Satellite unit has a number of configurations, and a configuration has a number of preset parameters.
User Defined buttons (User Defined parameters)
Assigning parameters to be User Defined parameters enables you to control the device from the ICP1 and the
DME64N/DME24N.
Refer to the “DME Designer Owner’s Manual” for details.
Introduction to the DME Satellite
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
10
Scene
A combination of all configuration and preset parameters is called a “scene.”
Scenes can be recalled from an ICP1, GPI device, other external controllers, DME64N/DME24N, or computer.
Up to 999 scenes can be stored for each device group.
Scene structure
Scene change
16 x 8
Scene
Scene 1
Scene 2
Scene 999
Component
Configuration
Preset
Parameter
Ex.: Gate
• Attack
• Decay
• Range
• Threshold
• Key in
• Hold
Matrix Mixer
First Act Dark Change Second Act
Band Set
Play Set
Stage Stage Stage
Play
Set
Band
Set
Band Set
Play Set
Scene 1 Scene Recall Scene 2
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
Introduction to the DME Satellite
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
11
Signal Types
DME Satellite audio system signals can be broadly categorized as follows.
Audio
Analog and digital signals are input and output between the DME Satellite, other DME series units, and other
audio devices. Analog signals are input and output via the [INPUT]/[OUTPUT] jacks. Digital signals are input
and output via the EtherSound jacks.
Control signals within a device group
Device group control signals control all DME series devices in the group.
There are two types of device group control signals, as follows:
Control signals between the computer and the group master DME series unit
Control signals between the group master DME series unit and the other DME series
units
You can use the DME Designer application to control the entire device group, such as sending components to the
devices and setting the parameters as required.
Control signals between devices outside the device group
These signals provide communication and control between individual devices.
Included in this category are MIDI messages transferred between [USB] connectors, GPI signals transferred be-
tween [GPI] connectors, and remote head amp control signals handled via the [REMOTE] connector.
Type of signals handled by the DME Satellite
Connector Audio Signal Device Control
Reference
Page
[USB] Connector
Control signals between computer and DME
Satellite
MIDI messages
page 18
[NETWORK] Connector
Control signals between computer and DME
Satellite
Control signals between DME Satellites
Control signals with a controller such as an
AMX or Crestron
page 20
page 29
EtherSound Connector
Up to 16 channels of input
and output.
Internal head amp control signals with a
digital mixer
Control signals with AVS-ESMonitor
page 24
page 28
[GPI] Connector
GPI control signals between GPI device (GPI
controller, etc.) and DME series unit
page 30
[REMOTE] Connector
Control signals to/from an external device
(such as AD8HR head amplifier)
Control signals for a digital mixer and
internal head amp
Control signals with a controller such as an
AMX or Crestron
MIDI messages
page 26
[INPUT]/[OUTPUT]
Connectors (audio in/out)
The number of I/O channels
depends on model.
page 25
1
2
3
Introduction to the DME Satellite
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
12
System Examples
Multiple DME Satellite units: Large-scale system
NOTE
Connect the computer to the [IN] connector of the first daisy-chained EtherSound device.
This connector can also be used in common with the same network as Ethernet Control.
•Units following the [OUT] connector of the first EtherSound device cannot be used in common with the same network as
Ethernet Control.
ICP1
Computer
Hub
Hub
Hub
Hub
M7CL
DME8i-ES
DME8i-ES
DME4io-ES
DME8o-ES
DME8o-ES
DME8o-ES
DME4io-ES
DME8o-ES
DME8i-ES
Space B
Space A
Space C
Space D
Analog In
Analog In
Analog In
Analog Out
Analog Out
Analog Out
Analog In
Analog In
Analog Out
Ethernet Control
Analog Audio
Analog Out
EtherSound
compatible
I/O card × 2
Primary
Master
EtherSound
Analog Out
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
Introduction to the DME Satellite
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
13
About DME Designer
DME Designer software enables you to integrate, configure, and control the DME series system from a connected
computer.
You can build the DME series audio system using graphic blocks in DME Designer that are displayed on the com-
puter monitor.
The DME series settings, configuration, and parameter data are transferred from the computer to the DME series
unit via the USB or Ethernet connection.
DME series settings, configuration, and parameter data is sent via USB or Ethernet to the connected DME series
unit. After the data is transmitted, you can disconnect the DME series unit from the computer and use it as an
independent processor.
You can also connect it to a computer and control it in realtime from DME Designer.
If multiple DME series units are connected in the network, DME Designer enables you to build a configuration
that includes those units.
Please download the DME Designer application, driver, DME setup manual, and DME Designer owner's manual
at the following URL:
http://www.yamahaproaudio.com/
Refer to the “Connecting to a Computer” (page 18) for more information on connecting a computer to the DME
Satellite. For details on how to install DME Designer and the drivers that are required for connection, refer to the
“DME Setup Manual”.
Refer to the DME Designer Owner’s Manual for setup and operation instructions.
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
14
Front Panel
1 [USB] Connector
Use this connector to connect the DME Satellite to the com-
puter’s USB port. If you plan to use a USB connection, you
must first install the USB-MIDI Driver on your computer.
Refer to the “DME Setup Manual” (PDF file) for installa-
tion instructions.
Be sure to follow the procedure below when you make a USB
connection with a computer. Otherwise, the computer and/
or DME Satellite may freeze, resulting in damages or loss of
data.
If the computer or DME Satellite freezes, turn the power to
the DME Satellite off and then on, then restart the comput-
er.
2 [NETWORK] Indicator
Lights orange while data communication is occurring via the
[USB] or [NETWORK] connector.
3 [MASTER] Indicator
Lights green when the device is operating as the group mas-
ter. The indicator is turned off if the device is operating as a
slave.
You can assign the group master in DME Designer.
Controls and Connectors
26
3451 7 8 9
26
3451 7 8 9
26
3451 7 8 9
DME8i-ES
DME8o-ES
DME4io-ES
•Before you connect the DME Satellite to the computer
via USB, cancel the computer’s energy saving mode
(such as Suspend, Sleep, or Stand-by mode).
•Before turning on the power to the DME Satellite, first
connect its [USB] connector to the computer’s USB
port.
•Before turning the power to the unit on or off, and
before connecting or disconnecting the USB cable, take
the following actions:
-Quit all open applications.
-Make sure that the DME Satellite is NOT transferring
any data.
•Be sure to wait six seconds or more between turning the
power to the unit on and then off (or off and then on),
or between connecting and disconnecting (or vice versa)
the USB cable.
CAUTION
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
Controls and Connectors
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
15
4 [ERROR] Indicator
Lights when an error occurs. The [PEAK] indicators reflect
the type of error. The [ERROR] indicator flashes when the
battery charge is getting low.
5 [TX/RX] Indicator
These indicate the communication status of the signals from
the EtherSound connector to the network. The transmission
status is shown by the [TX] indicator, and the reception sta-
tus by the [RX] indicator. The indicator will blink when sig-
nals are being sent correctly. The indicator will be dark if no
cable is connected to the EtherSound connector, or if com-
munication is not occurring successfully.
INPUT: Indicates the communication status of the
EtherSound [IN] connector.
OUTPUT: Indicates the communication status of the
EtherSound [OUT] connector.
6 [PEAK] Indicators
Light red when the signal level at the corresponding built-in
analog audio inputs or outputs ([INPUT] or [OUTPUT]
connectors) reaches or exceeds -3 dBFS. They also indicate
an error number or status.
7 [SIGNAL] Indicators
Light green when the signal level at the corresponding built-
in analog audio inputs or outputs ([INPUT] or [OUTPUT]
connectors) reaches or exceeds -40 dBFS. They also indicate
the status, for example, of the initialization process.
8 [POWER] Indicator
This will light when you turn the power on.
9 [POWER] Switch
Turns main power to the device on and off. The DME Sat-
ellite will start up with the same scene settings that were ac-
tive when it shut down. You can use the “Last Mem.
Resume” setting in DME Designer to set up the DME Sat-
ellite so that at startup it will recall the scene selected before
you turned off the power to the device.
Caution when turning the
power off
Do not turn off the power while the front panel
[SIGNAL] indicators are lighting consecutively in
the clockwise direction.
This indicates that data is being written into internal mem-
ory, and part of the data may be damaged if you turn off the
power at this time. Data writing will occur during the fol-
lowing operations.
While shifting to on-line operation
While storing or recalling or deleting scene memory
While saving changes to the Utility settings
While using the DME File Storage function to transmit/
receive or delete files
While updating the firmware, or while reverting to the
previous firmware following a failed update
NOTE
Remove the transparent protective film that was applied to the
indicator panel prior to shipment from the factory.
•If “Last Mem. Resume” is set to ON, the unit will back
up data to the internal memory periodically. In this
case, do not turn off the power to the unit within five
(5) seconds after you operate any parameters.
CAUTION
Lights consecutively in
the clockwise direction
Controls and Connectors
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
16
Rear Panel
1 [AC IN] Connector
Connect to the AC mains using the supplied AC power cord.
First connect the power cord to the DME Satellite, then in-
sert the power cord plug into an AC outlet.
2 Ground Screw
The supplied AC power cable is a 3-wire type, so if the AC
outlet used is properly earthed the DME Satellite will be
earthed as well. Hum and interference may by further re-
duced in some cases by also connecting the earth screw to an
earth point.
3 Cooling vent
The DME Satellite contains a cooling fan. The cooling air is
exhausted here, so please be careful not to block this vent.
4 [NETWORK] Connector
This is a 100Base-TX/10Base-T Ethernet connector for con-
nection to a computer or to another DME series unit in the
network. See “Ethernet Connection ([NETWORK] Con-
nector)” on page 20 for connection details.
5 Dip Switch
This 6-bit dip switch enables you to select the [REMOTE]
connector function or initialize the DME Satellite, depend-
ing on its setting at the startup of the device. To switch be-
tween RS-232C and RS-422 for the [REMOTE] connector
function, turn off the power to the device, set the dip switch
as shown below, then turn on the power to the device again.
See page 31 for the DME Satellite initialization procedure.
RS-232C RS-422
9
1 4 5 6
2
1 4 5 6
1 4 5 6
)
9
8
7
7
8
8
)
7
3
2 3
2 3
DME8i-ES
DME8o-ES
DME4io-ES
Even when the power switch is turned off,
electricity is still flowing to the product all the
minimum level. When you are not using the
product for a long time, make sure to unplug the
power cord from the wall AC outlet.
CAUTION
NOTE
Use a STP (Shielded Twisted Pair) cable for this connection to
prevent electromagnetic interference.
If you do not plan to initialize the DME Satellite,
set all dip switch bits (excluding one bit for the
RS-422 setting) in the upper position.
RS-232C
RS-422
RS-232C
RS-422
CAUTION
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
Controls and Connectors
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
17
6 [REMOTE] Connector
This 9-pin D-SUB connector allows connection to a Yamaha
AD824 or AD8HR remote head amplifier or an RS-232C/
RS-422 compatible controller such as those from AMX or
Crestron. You can also connect a Yamaha PM5D or DM2000
and control the internal head amps of the DME8i-ES/
DME4io-ES. See “Remote Connection ([REMOTE] Con-
nector)” on page 26 for connection details.
7 EtherSound [IN]/[OUT] Connectors
These connectors input and output audio signals and control
signals between devices. Use an Ethernet cable (CAT5e or
higher category) to daisy-chain multiple DME Satellite
units.
For more about EtherSound connections, refer to pages 24
and 28.
8 [GPI] Connector
This Euroblock connector provides access to the unit’s GPI
(General Purpose Interface) interface for transfer of control
signals to and from external equipment. It features 8-port in-
put and 4-port output. The +V terminals have an output
voltage of 5 volts. The IN terminal detects voltage changes
from 0V to 5V. The OUT terminals output either signal “L”
or “H” at a TTL level. (See page 30.)
9 [INPUT] Connectors
These Euroblock connectors receive 8-channel analog audio
signals on the DME8i-ES.
These Euroblock connectors receive 4-channel analog audio
signals on the DME4io-ES.
) [OUTPUT] Connectors
These Euroblock connectors output 8-channel analog audio
signals on the DME8o-ES.
These Euroblock connectors output 4-channel analog audio
signals on the DME4io-ES.
Precautions for Using a
Rack-mounted DME Satellite
If several DME Satellite units (or a DME Satellite unit to-
gether with other devices) are installed in a poorly-ventilated
rack, the heat generated by each unit may raise the tempera-
ture inside the rack, preventing the DME Satellite from per-
forming as designed. When mounting DME Satellite units
in a rack, please leave one rack space vacant for every two
units. You can attach a ventilation panel to this space or leave
it open to prevent excessive heat build-up.
If the temperature inside the rack is expected to rise above 40
degrees Celsius or 104 degrees Fahrenheit (or if the ambient
temperature outside the rack is expected to rise above 30 de-
grees Celsius or 86 Fahrenheit), install a fan kit in the top
row of the rack. The fan must provide airflow of 1.6m
3
/min
or more and static pressure of 5mmH
2
O or more.
NOTE
The communication status of the EtherSound [IN]/[OUT]
jacks is shown by the front panel [TX/RX] indicators.
•Use a STP (Shielded Twisted Pair) cable to prevent
electromagnetic interference.
NOTE
The PAD will be internally switched on or off when the gain of
the DME8i-ES/DME4io-ES internal head amp is adjusted
between –6 dB and –5 dB. Keep in mind that noise may be
generated if there is a difference between the Hot and Cold
output impedance of the external device connected to the
INPUT connector when using phantom power.
Ventilation panel
DME Satellite
DME Satellite
DME Satellite
DME Satellite
Fan kit
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
18
USB Connection
To connect multiple DME Satellite units to a network, you must assign appropriate IP addresses and make other
network settings on all units. To achieve this, you need to connect the [USB] connector of one of the DME Sat-
ellite units to the USB port of the computer using USB cables, install USB-MIDI Driver and DME Designer on
the computer, then assign the IP addresses to the DME Satellite units from DME Designer.
USB connections can be used in the following three ways:
(1) Set up the network (e.g., assign a unique IP address to each DME Satellite) from DME Designer.
(2) Control the DME Satellite from DME Designer.
(3) Connect to any individual DME Satellite and control that DME Satellite unit by transmitting MIDI com-
mands from a MIDI sequencer or similar software.
Connecting to a Computer
NOTE
•Refer to the “DME Setup Manual” (PDF file) for details on installing USB-MIDI Driver and DME Designer.
•Make sure that the USB-MIDI Driver’s THRU setting is “OFF.”
•Refer to “Network Settings” on page 19 for more information on assigning IP addresses from DME Designer.
NOTE
The computer on which DME Designer is running can be connected to either the group master or a slave DME series unit.
In this case, set the DME Satellite as the group master.
The correspondence between the MIDI commands to be received/transmitted and the scene parameters can be set up using
DME Designer.
The USB port being used by DME Designer is not available for use by a MIDI sequencer or other application.
HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE
ENTERENTERCANCELCANCEL
Device Group
DME Satellite
Computer
(Running DME Designer.)
Computer
(Running MIDI
Sequencer or
similar application.)
Ethernet Cable
Switching Hub
Ethernet Cable
DME Satellite
Ethernet
Straight Cable
DME64N/24N
USB Cable
USB Cable
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
Connecting to a Computer
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
19
Network Settings
Use DME Designer to specify the IP address, master/slave, and master ID settings as follows.
Setting the IP address
Each group of digits between periods in an IP address is called an “octet.” These groups of digits are called “1st
octet,” “2nd octet,” etc., starting from the left-most digit group.
You cannot specify 0, 127, or 223 through 255 for the 1st octet of the network address.
You can specify the following range of values for the 4th octet.
Master : 2-253
Slave : 3-253
Master and slave setting
Each device group must have one master. All other devices in the group are assigned as slave.
The fourth octet of a slave DME Satellite’s master ID must be the same value as the fourth octet of the group
master DME Satellite’s IP address.
NOTE
•Subnet mask is fixed at 255.255.255.0.
The network address of Gateway is the same as that of IP address. The host address of Gateway is automatically set to 254.
Assign each of DME series units a unique IP address so that there are no duplicates. Assigning duplicate IP addresses may
cause serious network problems.
•You cannot make any network settings while using the DME Designer application on-line. To make network settings, first
set DME Designer off-line. Refer to the DME Designer Owner’s Manual for details.
NOTE
When using a DME Satellite together with the DME64N/24N, you must assign the DME Satellite (including the DME8i-C/
DME8o-C/DME4io-C) as the master. If you assign the DM64N/24N as the device group master, you will be unable to
synchronize using DME Designer.
Network Address Host Address
Connecting to a Computer
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
20
Ethernet Connection ([NETWORK] Connector)
To control the DME Satellite from the computer via Ethernet, use an Ethernet cable to connect the [NET-
WORK] connector on the rear panel of the DME Satellite to the computer, then install DME-N Network Driver.
Two DME Satellite units directly connected via Ethernet
You can connect devices in the same device group directly to each other using Ethernet cables, without connecting
them to a switching hub. If they are DME Satellite units, you can use either crossover cables or straight cables. In
this case, from DME Designer set Link Mode on both units to the same setting. Devices in different subnet (dif-
ferent network address) groups can be connected via a router or layer-3 compliant switching hub.
NOTE
•Refer to the “DME Setup Manual” (PDF file) for details on installing DME-N Network Driver.
•Appropriate IP addresses must first be assigned to all devices connected to an Ethernet network. Connect your computer to
one of the DME Satellite units via USB, then assign the IP addresses from DME Designer (page 18).
HINT
Since the DME Satellite supports Auto MDI/MDI-X, it will automatically detect whether the connected cable is of the
straight type or crossover type, and will configure itself to create the optimal connection. Therefore, you can use either a
straight or crossover cable.
DME Satellite
DME Satellite
Ethernet Cable
USB Cable
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
Connecting to a Computer
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
21
Control from a computer in the same subnet group
NOTE
The IP addresses in the diagram are examples.
•Use a switching hub that is compatible with 100Base-TX/10Base-T network speeds.
The maximum length of a cable between a switching hub and the DME Satellite is 100 meters. Due to the quality of cables
and switching hub performance, however, proper operation at the maximum length cannot be guaranteed in some cases.
Use a STP (Shielded Twisted Pair) cable to prevent electromagnetic interference.
•If you are using multiple DME series units, set Link Mode on each unit to the same setting. Yamaha recommends that you
select 100Base-TX for the Link Mode setting.
•You can also connect a supported controller such as the AMX or Crestron, and control the DME Satellite remotely. For
details, refer to “Connecting to an External Device” on page 26.
HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE
ENTERENTERCANCELCANCEL
Device Group
Group Master
DME Satellite (IP address: 192.168.0.7)
Ethernet Cable
Switching Hub
Ethernet Straight Cable
Computer
(IP address:
192.168.0.100)
Ethernet Cable
Ethernet
Straight Cable
DME Satellite
(IP address: 192.168.0.3)
(Master ID: 7)
DME64N/24N
(IP address: 192.168.0.250)
(Master ID: 7)
Connecting to a Computer
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
22
Control from a computer with a different subnet
HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE
ENTERENTERCANCELCANCEL
Device Group
Group Master
DME Satellite (IP address: 192.168.0.5)
Ethernet Cable
Ethernet Cable
Ethernet
Straight Cable
Ethernet
Straight Cable
Ethernet
Straight Cable
Switching Hub
Router or
Layer-3
Compliant
Switching
Hub
Computer
Port settings
• Destination network address: 192.168.0.0
• Subnet mask: 255.255.255.0
• Gateway: 192.168.0.254
DME Satellite
(IP address: 192.168.0.3)
(Master ID: 5)
DME64N/24N
(IP address: 192.168.0.12)
(Master ID: 5)
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
Connecting to a Computer
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
23
Connecting multiple device groups
HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE
ENTERENTERCANCELCANCEL
HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE
ENTERENTERCANCELCANCEL
Device Group 1 Device Group 2
Group Master
DME Satellite
(IP address: 192.168.0.2)
Group Master
DME Satellite
(IP address: 192.168.0.3)
Ethernet Cable Ethernet Cable
Ethernet
Straight Cable
Ethernet Cable
DME64N/24N
(IP address: 192.168.0.100)
(Master ID: 2)
DME Satellite
(IP address: 192.168.0.40)
(Master ID: 2)
DME Satellite
(IP address: 192.168.0.10)
(Master ID: 3)
DME64N/24N
(IP address: 192.168.0.200)
(Master ID: 3)
Switching Hub
Computer
(IP address: 192.168.0.1)
Switching Hub
Ethernet Straight Cable
Ethernet Straight Cable
Ethernet Cable
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
24
Digital Audio Connection (EtherSound Connectors)
You can use the DME Satellite’s EtherSound connector to input and output digital audio signals, control signals,
and word clock signals. When connecting DME Satellites, make daisy-chain connections between the EtherSound
[OUT] connector [IN] connector, and the [OUT] connector [IN] connector.
Audio signals and word clock signals can also be input and output between EtherSound compatible devices and
devices such as mixers in which the MY16-ES64 card has been installed. Input and output of audio signals and
word clock signals can be specified using the “AVS-ESMonitor” application software made by AuviTran SARL.
For details on interface cards and application software, refer to the appropriate Owner’s Manual.
Example: Connection to EtherSound devices
Audio I/O Connection
About AVS-ESMonitor
AVS-ESMonitor is application software made by the AuviTran SARL for the purpose of monitoring and con-
trolling an EtherSound system. It allows you to make various EtherSound settings such as input/output rout-
ing.
For details, refer to the following website.
http://www.auvitran.com/view.php?products_AVS-ESMonitor.php
NOTE
DME Satellites and the MY16-ES64 can transmit and receive control data such as for internal head amps via EtherSound.
However in some cases, it may not be possible to transmit or receive control data depending on the device in which the MY
card is installed. For details, refer to the operating manual of the device in which the card is installed.
•For details on EtherSound specifications and the length of the cables that can be used, refer to the following website.
http://www.ethersound.com/
HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE
ENTERENTERCANCELCANCEL
EtherSound
[OUT] connector
DME Satellite DME Satellite
DME64N/24N
Ethernet CableEthernet Cable
EtherSound
[OUT] connector
EtherSound
[IN] connector
EtherSound
[IN] connector
MY16-ES64
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
Audio I/O Connection
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
25
Analog Audio Connection ([INPUT] & [OUTPUT] Connectors)
The DME Satellite can directly input and output audio signals via the [INPUT] and [OUTPUT] connectors.
Wire the supplied Euroblock plugs (3P) as shown below. You can use DME Designer to set the head amplifier
gain and turn the phantom power on and off for each [INPUT] connector.
Euroblock plug connection
Please be sure to use the supplied Euroblock plugs. If you lose them, contact your nearest Yamaha dealer.
Cable preparation
•To prepare the cable for attachment to a Euroblock connector, strip the
wire as shown in the illustration, and use stranded wire to make
connections. With a Euroblock connection, the stranded wire may be
prone to breakage because of metal fatigue due to the weight of the
cable or due to vibration. When rack-mounting your equipment, use a
lacing bar when possible to bundle and fasten the cables.
•If cables will be frequently connected and disconnected, as in the case
of a portable installation, we recommend that you use ferrules with
insulation sleeves. Use a ferrule whose conductor portion has an
external diameter of 1.6 mm (1.3 mm for GPI) or less, and a length of
approximately 7 mm (5 mm for GPI) (such as the AI0,5-6WH made
by the Phoenix Contact corporation).
1. Loosen terminal screws.
2. Insert cables.
3. Securely tighten terminal screws.
Pull the cables (not too strongly) to confirm that they are
securely connected.
4. Insert the Euroblock plug into the Euroblock
connector on the rear panel.
NOTE
Use a slotted screwdriver with a blade width of about 3 millimeters to secure the cables to the
(3P) Euroblock plug.
Use a slotted screwdriver with a blade width of about 2 millimeters to secure the cables to the
(16P) Euroblock plug to connect to the [GPI] connector.
If you use stranded wire, do not tin (plate with solder) the exposed end.
3 mm
1.6 mm (1.3 mm for GPI)
or less
approx.7 mm
(5 mm for GPI)
approx.7 mm
(5 mm for GPI)
CAUTION
Loosen
Slotted Screwdriver
Euroblock Plug
Terminal Screw
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
26
Remote Connection ([REMOTE] Connector)
The [REMOTE] connector of the DME Satellite can be connected to remotely-controllable Yamaha AD8HR or
AD824 head amplifiers (pre-amps), digital mixers, or RS-232C compatible controllers (such as those from AMX
or Crestron). The [REMOTE] connector also transmits and receives MIDI messages.
Controlling external head amplifiers from the DME Satellite
You can remotely control the AD8HR or AD824 head amplifier settings from DME Designer. Up to eight
AD8HR/AD824 head amplifiers can be connected.
Be sure to set the dip switch on the rear panel of the DME Satellite to “RS-422” (page 16) when connecting to
AD8HR or AD824 remote head amplifiers. Do not change the dip switch setting to any position other than to
“RS-422” while the devices are connected to prevent possible damage to the device(s).
When connecting to a combination of AD8HR and AD824 head amplifiers, be sure to place the AD8HR units
closest to the DME Satellite in the chain, otherwise the AD8HR or AD824 unit(s) may not be properly recognized
by the DME Satellite.
Connecting to an External Device
NOTE
Only control signals are transmitted and received via the REMOTE connection. Audio connections must be made separately.
D-SUB 9-pin Cable (Interlink Crossover)
REMOTE
HA REMOTE 2HA REMOTE 1 HA REMOTE 1 HA REMOTE 2
AD8HR AD8HR
AD824 AD824 AD824
DME Satellite
COM PC/RS-422 COM RS-422 COM PC/RS-422 COM RS-422 COM PC/RS-422
Set to RS-422
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
Connecting to an External Device
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
27
Controlling a DME Satellite’s internal head amps from a digital mixer
The internal head amp settings of a DME8i-ES or DME4io-ES can be remotely controlled from a digital mixer
such as the Yamaha PM5D or DM2000.
Connect the digital mixer to the DME series’ [REMOTE] connector, and use an Ethernet cable to make connec-
tions between the [NETWORK] connectors of the DME series.
From the digital mixer, DME series units can be controlled as an AD8HR. The gain and the phantom power
(+48V) can be controlled.
Controlling the DME Satellite from an external device
You can remotely control the DME Satellite from a connected RS-232C or RS-422 compatible controller, such
as those from AMX or Crestron.
Be sure to set the dip switch on the rear panel of the DME Satellite correctly (page 16) in accordance with a con-
nected RS-232C or RS-422 compatible remote controller. Do not change the dip switch setting to any other po-
sition while the devices are connected to prevent possible damage to the device(s).
NOTE
•Only one mixer can be connected within each device group.
The digital mixer can be connected to any DME series unit, whether it is the group master or a slave unit.
The ID number of the DME series unit being remotely controlled is specified from DME Designer.
For details on making this setting, refer to the “DME Designer Owner’s Manual.”
•If the connection between DME series units is broken, it will no longer be possible to communicate with DME units of an
ID number that follows the disconnected DME.
The variable range of GAIN differs between the AD8HR and the DME Satellite. You cannot use the mixer to specify a value
that exceeds the variable range of the DME Satellite.
NOTE
The port used for remote control is specified from DME Designer. For details on making this setting, refer to the “DME
Designer Owner’s Manual.”
•Refer to “DME Remote Control Protocol Specifications” on the Yamaha web site for more information on communication
protocols used to control the DME Satellite from an external device (such as those from AMX or Crestron).
http://www.yamahaproaudio.com/
D-SUB 9-pin Cable
DME Satellite
DME Satellite
DME Satellite
DME Satellite
Ethernet
Cable
Switching
Hub
REMOTE REMOTE
Digital Mixer
Connecting to an External Device
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
28
EtherSound Connection (EtherSound Connectors)
You can use the EtherSound connector to control the DME Satellite’s internal head amp or other functionality.
Controlling DME Satellite’s internal head amps from a digital mixer
The internal head amp settings of a DME8i-ES or DME4io-ES can be remotely controlled from a digital mixer
such as the Yamaha PM5D or DM2000.
Connect the digital mixer using a D-sub 9-pin cable to the MY16-ES64 card, and use EtherSound to make con-
nections between the MY16-ES64 card and DME series. Use an Ethernet cable connected to the [NETWORK]
connectors to make connections between DME series units.
The gain and the phantom power (+48V) can be controlled from the digital mixer.
NOTE
•Only one mixer can be connected within each device group.
The digital mixer can be connected to any DME series unit, whether it is the group master or a slave unit.
Control signal settings are made using AuviTrans “AVS-ESMonitor” application software. Refer to the DME Designer
manual for details.
The ID number of the DME series unit being remotely controlled is specified from DME Designer.
For details on making this setting, refer to the “DME Designer Owner’s Manual.”
•If the connection between DME series units is broken, it will no longer be possible to communicate with DME units of an
ID number that follows the disconnected DME.
•For details on controlling the head amps from a digital mixer not equipped with a [REMOTE] connector, refer to the
mixer’s owner’s manuals.
Digital Mixer
EtherSound
DME8i-ES
DME8i-ES
DME4io-ES
DME4io-ES
Ethernet
Cable
Switching
Hub
EtherSound
Ethernet
Ethernet Switching Hub
Hub
MY16-EX
MY16-ES64
D-Sub 9-pin
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
Connecting to an External Device
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
29
Network Connection ([NETWORK] Connectors)
You can connect a controller such as the AMX or Crestron to DME Satellites via Ethernet, and remotely control
multiple DME Satellite units.
NOTE
The port used for remote control is specified from DME Designer. For details on making this setting, refer to the “DME
Designer Owner’s Manual.”
•Refer to “DME Remote Control Protocol Specifications” on the Yamaha web site for more information on communication
protocols used to control the DME Satellite from an external device (such as those from AMX or Crestron).
http://www.yamahaproaudio.com/
Connecting to an External Device
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
30
GPI Connection ([GPI] Connector)
A GPI (General Purpose Interface) device (GPI controller, etc.) can be connected to the rear panel [GPI] connec-
tors to enable the transfer of a variety of control signals. Optional CP4SW, CP4SF, and CP1SF Control Panels
can be also connected via GPI.
The DME Satellite features 8-port GPI input and 4-port GPI output. The +V terminals have an output voltage
of 5 volts. The IN terminal detects voltage changes from 0V to 5V. The OUT terminals output either signal “L”
or “H” at a TTL level.
The parameters for each GPI input and output are assigned via the DME Designer application.
Euroblock connectors are used for all GPI input and output connections. Euroblock connection methods are de-
scribed in “Euroblock plug connection” on page 25 in this manual.
NOTE
•For more information on the CP4SW, CP4SF, and CP1SF Control Panels, refer to the CP4SW/CP4SF/ CP1SF Owner’s
Manual.
•You can use DME Designer to set up the system so that scene recall operations and User Defined parameter control can be
carried out from connected GPI control devices. Refer to the DME Designer Owner’s Manual for details.
NOTE
You can use DME Designer to adjust the input calibration parameters for the [GPI] connector.
1234
IN +V
IN +V GND
OUT GND
1234
1234
Example: Controlling the DME
Satellite from a switch box
Example: Controlling the DME Satellite via a
10k ohm linear taper potentiometer.
Example: Lighting LED indicators on the
external devices from the DME Satellite
GPI Connection GPI Connection
Continuous Variable Volume
Max. 16mA
DME Satellite [GPI] Connector
DME Satellite [GPI] Connector DME Satellite [GPI] Connector
Euroblock Plug
Remote Switch Box Remote Fader Box
Switches
Remote LED Box
10k ohm Linear
Taper Potentiometer
LEDs and Resistors
GPI Connection
Make sure that the current between the
OUT and GND [GPI] connectors is
less than 16mA.
CAUTION
Euroblock Plug Euroblock Plug
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
31
Initializing the DME Satellite
You can initialize the DME Satellite internal memory.
Select one of the following initialization types:
Initialize DME:
All scenes, preset parameter settings and WAVE files except components and files saved via the File Storage func-
tion will be deleted. The Utility settings will be set to default values.
Delete All Data:
All stored component, scene, preset parameter settings, WAVE files, and files saved via the File Storage function
will be deleted. The Utility settings will be set to default. Use this initialization type if the internal data is damaged
or corrupted. After initialization, transfer necessary components from DME Designer.
1. While the DME Satellite is turned off, set the dip switch on the rear panel to the following
position, then turn on the power to the unit.
Four [PEAK] indicators on the upper row on the front panel light up during the initialization process. Four
[SIGNAL] indicators on the lower row of the front panel flash when the initialization process is complete. Four
[PEAK] indicators on the lower row of the front panel flash if the initialization process fails.
2. When initialization is complete, reset the dip switch to its previous position (page 16),
then turn off and on the power to the unit.
Other Functions
Do NOT turn off the power to the DME Satellite during the initialization process to prevent possible
damage to the device.
Be sure to reset the dip switch to the previous position to prevent possible damage to the device.
RS-232C
RS-422
Initialize DME:
Delete All Data:
RS-232C
RS-422
CAUTION
CAUTION
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
32
Options
The ICP1, CP4SW, CP1SF, and CP4SF controllers are available as options for remote external control of the DME series. The
ICP1 connects via Ethernet, while the CP4SW, CP1SF, and CP4SF connect via the GPI interface. For more information on
installing your Control Panel and connecting it to a DME series unit, refer to the owner’s manual that came with the Control
Panel. For more information on settings, refer to the DME Designer Owner’s Manual.
ICP1
This controller connects to a DME series unit via Ethernet. Like the DME series units, a unique IP address must
be assigned to each controller unit. Data is transmitted and received via Ethernet cables.
You can assign and control any function of all DME series units in the same device group via the controller.
Up to four parameter sets can be assigned to six function keys (F1 – F6) located above and under the LCD. You
can control up to 24 parameters by selecting a display page using the [HOME] key.
CP4SW, CP4SF, and CP1SF
These controllers connect to DME series units via the [GPI] connectors. These controllers control only the DME
series units to which they are directly connected. The controller switches enable you to turn the parameter settings
On and Off. The switch LEDs enable you to check the parameter status. The faders enable you to control the
parameter values.
References
CONTROL PANEL
CP4SW
10
0
CONTROL PANEL
CP1SF
10
0
10
0
10
0
10
0
CONTROL PANEL
CP4SF
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
References
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
33
Troubleshooting
Component
Refer to the DME Designer Owner’s Manual for more information on each component.
The device does not turn on, or the panel
LEDs do not light up.
Connect the power cord properly (page 7).
Make sure that the [POWER] switch is turned ON (page 15).
If the device still does not turn on, contact a Yamaha dealer.
No communication between the DME
Satellite and the DME Designer
application software.
Connect the cable properly (page 18, 20).
Make sure that USB-MIDI Driver has been installed correctly.
If the [NETWORK] connector is being used for connection, make sure that you have set
the DME-N Network Driver correctly.
The DME Designer version should be 3.0 or later.
Make the Port setting.
No audio input is present.
Connect the cable properly.
Check to see if signals are being received from an external device.
Did you use AVS-ESMonitor to make EtherSound settings such as routing?
Set the gain of the internal head amplifier or external head amplifier to an appropriate
level.
No audio is output.
Connect the cable properly.
Did you use AVS-ESMonitor to make EtherSound settings such as routing?
Make sure that the output level set in DME Designer is not too low.
Make sure that the Mute setting in DME Designer is set to Off.
•You may have designed a scene in DME Designer that mutes audio output.
•You may have tried to use a configuration at 96 kHz that does not support 96 kHz.
The selected scene changes
unexpectedly.
Use DME Designer to check the MIDI Program Change assignments.
Use DME Designer to check the GPI input assignments.
MIDI messages cannot be transmitted or
received.
Make sure that the power to the MIDI device is turned on.
Set the MIDI port properly.
Set the receive and transmit channels properly.
Scenes cannot be recalled via MIDI
Program Change messages.
Use DME Designer to change the setting so that the required MIDI Program Change
messages will be received properly.
Make the appropriate Program Change Table settings via DME Designer.
Parameters cannot be controlled via MIDI
Control Change messages.
Use DME Designer to set the parameters correctly to allow Control Change message
reception.
Make the appropriate MIDI Control Change Table settings via DME Designer.
Parameters cannot be edited via MIDI
Parameter Change messages.
Use DME Designer to set the parameters correctly to allow Parameter Change message
reception.
Make the appropriate MIDI Parameter Change Table settings via DME Designer.
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
References
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
34
MIDI Data Format
1. MIDI functions on the DME8i-ES,
DME8o-ES, and DME4io-ES
1.1 Scene Change
Scene recall occurs according to the “MIDI Program Change Ta-
ble” assignments when appropriate MIDI Bank Select MSB/LSB
and Program Change messages are received by the DME8i-ES/
DME8o-ES/DME4io-ES.
When a scene recall operation is carried out via DME Designer,
corresponding MIDI Bank Select MSB/LSB and Program Change
messages are also transmitted by the DME8i-ES/DME8o-ES/
DME4io-ES as specified by the “MIDI Program Change Table” as-
signments.
Transmission does not occur while configurations are being
switched.
1.2 Parameter Control
MIDI Control Change and Parameter Change messages trans-
mitted to the DME8i-ES/DME8o-ES/DME4io-ES can be
used to control parameters according to the “MIDI Control
Change Table” and “MIDI Parameter Change Table” assign-
ments.
When a parameter is edited via DME Designer, correspond-
ing MIDI Control Change and Parameter Change messages
are also transmitted by the DME8i-ES/DME8o-ES/
DME4io-ES as specified by the “MIDI Control Change Ta-
ble” and “MIDI Parameter Change Table” assignments.
2. MIDI Data Flow
3. MIDI Setup
Specifies basic MIDI operation. Use DME Designer to make the
setting.
3.1 Host Select
Selects the input/output ports to be used for MIDI communica-
tion.
3.2 MIDI Tx Channel
Specifies the MIDI transmit channel (1 ~ 16).
3.3 MIDI Rx Channel
Specifies the MIDI receive channel (1 ~ 16).
3.4 MIDI Tx Switch
Program Change Tx Switch: turns Bank Select MSB, LSB, and
Program Change transmission on or off.
Control Change Tx Switch: turns Control Change transmission on
or off.
Parameter Change Tx Switch: turns Parameter Change transmis-
sion on or off.
3.5 MIDI Rx Switch
Program Change Rx Switch: turns Bank Select MSB, LSB, and
Program Change reception on or off.
Control Change Rx Switch: turns Control Change reception on or
off.
Parameter Change Rx Switch: turns Parameter Change reception
on or off.
3.6 MIDI Omni Switch
Program Change Omni Switch: turns the Bank Select MSB, LSB,
and Program Change omni mode on or off.
Control Change Omni Switch: turns the Control Change omni
mode on or off.
3.7 MIDI Echo Back Switch
Program Change Echo Back Switch: turns Bank Select MSB, LSB,
and Program Change echo back on or off.
Control Change Echo Back Switch: turns Control Change echo
back on or off.
Parameter Change Echo Back Switch: turns Parameter Change
echo back on or off.
“MIDI Program Change Table,” “MIDI Control Change Table,” and “MIDI
Parameter Change Table” assignments can be made via DME Designer.
Refer to the DME Designer Owner’s Manual for details.
SW1: Program Change Rx Switch [On/Off]
SW2: Control Change Rx Switch [On/Off]
SW3: Parameter Change Rx Switch [On/Off]
SW4: Program Change Echo Back Switch [On/Off]
SW5: Control Change Echo Back Switch [On/Off]
SW6: Parameter Change Echo Back Switch [On/Off]
SW7: Program Change Tx Switch [On/Off]
SW8: Control Change Tx Switch [On/Off]
SW9: Parameter Change
MIDI Rx CH: MIDI Rx Channel (1-16)
MIDI IN
MIDI OUT
MIDI Rx CH
Bank Select MSB/LSB
Program Change
(Scene Recall)
Bank Select MSB/LSB
Program Change
(Echo Back)
Bank Select MSB/LSB
Program Change
MIDI THR
U
Control Change
(Parameter Edit)
Control Change
(Echo Back)
Control Change
Parameter Change
(Parameter Edit)
Parameter Change
Parameter Change
(Echo Back)
MIDI Tx CH
SW1
SW2
SW3
SW4
SW5
SW6
SW7
SW8
SW9
MIDI Tx CH: MIDI Tx Channel (1-16)
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
References
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
35
4. MIDI Format
MIDI Format Chart (Rx: receive, Tx: transmit}
4.1 Program Change (Cnh)
Receive
When the “Program Change Rx Switch” is on, Program Change
messages are received on the MIDI channel specified by the “MIDI
Rx Channel” parameter.
If the “Program Change Omni Switch” is also on, however, Pro-
gram Change messages will be received on all MIDI channels re-
gardless of the “MIDI Rx Channel” setting.
When a Program Change message is received, the scene assigned to
the received program number in the “MIDI Program Change Ta-
ble” is recalled.
The effective Bank Select, Program Change range is as follows:
Transmit
When the “Program Change Tx Switch” is on and a scene is
switched from DME Designer, the corresponding Program Change
number will be transmitted as specified by the “MIDI Program
Change Table” and “MIDI Tx Channel” settings.
If multiple Program Change numbers are assigned to a single scene,
the Bank Select MSB/LSB and Program Change number corre-
sponding to the lowest number will be transmitted.
Bank Select MSB
Bank Select LSB
Program Change No.
4.2 Active Sensing (FEh)
Receive
MIDI communication will be initialized if no data is received with-
in 300 ms after reception (Running Status, etc., will be cleared).
Active Sensing
4.3 Control Change (Bnh)
Receive
When the “Control Change Rx Switch” is on, Control Change
messages are received on the MIDI channel specified by the “MIDI
Rx Channel” parameter.
If the “Control Change Omni Switch” is also on, however, Control
Change messages will be received on all MIDI channels regardless
of the “MIDI Rx Channel” setting.
Control Change parameter resolution is 128 regardless of the effec-
tive range of the parameter.
For finer settings use Parameter Change.
Transmit
When the “Control Change Tx Switch” is on and a parameter is ed-
ited via DME Designer, appropriate Control Change data will be
transmitted as specified by the “MIDI Control Change Table” and
“MIDI Tx Channel” settings.
Refer to “Supplementary Information 1” for cases in which multi-
ple messages are assigned to a single parameter.
4.4 Parameter Change (F0h - F7h)
Receive
When the “Parameter Change Rx Switch” is On, Parameter
Change messages are received on the MIDI channel specified by the
“Device ID (Rx Ch)” parameter.
Number Format Notation
Numbers ending with “h” are in hexadecimal format, while numbers
ending with “b” are binary format.
Characters “A” through “F” in hexadecimal numbers represent decimal
values 10 through 15. Other lower-case characters (usually “n” or “x”)
can represent any number.
Command Rx/Tx Function
Channel
Message
Control Change
(Bnh)
Rx/Tx
Editing the
parameters
Program Change
(Cnn)
Rx/Tx Scene Recall
System Real-time
Message
TIMING CLOCK
(F8h)
Rx
MIDI Clock
Receive
ACTIVE SENSING
(FEh)
Rx
MIDI Cable
Check
System Exclusive
Message
Parameter
Change
Rx/Tx
Editing the
parameters
Bank Select MSB: 0
Bank Select LSB: 0-7
Program Change No.: 0-127
Status Bnh (1101nnnnb) Control Change
Data 00h (00000000b) Control Change No. 0 (Bank
Select MSB)
Data nnh (0nnnnnnnb) Control Value (Bank Select
MSB No.)
Status Bnh (1101nnnnb) Control Change
Data 20h (00100000b) Control Change No. 32 (Bank
Select LSB)
nnh (0nnnnnnnb) Control Value (Bank Select
LSB No.)
Status Cnh (1100nnnnb) Program Change
Data nnh (0nnnnnnnb) Program Change No. (0-127)
Status FEh (11111110b) Active Sensing
Status Bnh (1011nnnnb) Control Change
Data cch (0cccccccb) Control Change No. (1-31,33-
95,102-119)
vvh (0vvvvvvvb) Control Value (0-127)
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
References
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
36
Transmit
When the “Parameter Change Tx Switch” is On and a parameter is
edited via DME Designer, appropriate Parameter Change data will
be transmitted as specified by the “MIDI Parameter Change Table”
and “MIDI Tx Channel” settings.
Refer to “Supplementary Information 1” for cases in which multi-
ple messages are assigned to a single parameter.
Refer to “Supplementary Information 2” for information on setting
Parameter Data values.
Supplementary Information 1
Messages Transmitted When Multiple Messages are Assigned to
the Same Parameter
The DME8i-ES/DME8o-ES/DME4io-ES MIDI transmit messag-
es are specified via the “MIDI Control Change Table” and “MIDI
Parameter Change Table.”
(The “MIDI Control Change Table” and “MIDI Parameter
Change Table” can be set up via DME Designer.)
Multiple messages can be assigned to a single parameter, but the
DME8i-ES/DME8o-ES/DME4io-ES will only transmit one of the
assigned messages.
The transmitted messages are as follows:
If a Control Change message and a Parameter Change message
are assigned to the same parameter
the Control Change message will be transmitted.
If multiple Control Change numbers are assigned to the same pa-
rameter
the smallest Control Change number message will be trans-
mitted.
If multiple Parameter Change numbers are assigned to the same
parameter
the smallest Parameter Change number message will be trans-
mitted.
Supplementary Information 2
Setting the Parameter Change Message Parameter Data Values
The Parameter change parameter values are expressed as 32-bit in-
tegers with or without parity.
•A parity bit (positive:0, negative:1) is added above the most sig-
nificant value bit (bit 31).
Fractional parameters will be converted according to the integer
table.
For integers with parity, negative numbers are expressed as the
2’s complement.
Status F0h (11110000b) System Exclusive Message
ID No. 43h (01000011b) Manufacturer’s ID
No.(YAMAHA)
DEVICE ID. 1xh (0001xxxxb) Rx/Tx Channel (0-15)
GROUP ID. 3Eh (00111110b) Digital Mixer
MODEL ID. 10h (00010000b) Device Code (DME)
Parameter
Address
aah (0aaaaaaab) Parameter Address High
aah (0aaaaaaab) Parameter Address Low
Parameter
Data Value
ddh (0dddddddb) data 0
ddh (0dddddddb) data 1
ddh (0dddddddb) data 2
ddh (0dddddddb) data 3
ddh (0dddddddb) data 4
EOX F7h (11110111b) End of Exclusive
00000000000000000000000001111101000
00111111111111111111111110000011000
data 0 data 1 data 2 data 3 data 4
000 003E
8
data 0 = 00h data 1 = 00h data 2 = 00h data 3 = 07h data 4 = 68h
bit0
bit1
bit2
bit3
bit4
bit5
bit6
bit7
bit8
bit9
bit10
bit11
bit12
bit13
bit14
bit15
bit16
bit17
bit18
bit19
bit20
bit21
bit22
bit23
bit24
bit25
bit26
bit27
bit28
bit29
bit30
bit31
00
FFFFFC18
data 0 = 1Fh data 1 = 7Fh data 2 = 7Fh data 3 = 78h data 4 = 18h
parity
Example:
• Decimal value 1000Hexadecimal value 3E8h
• Decimal value 1000 Hexadecimal value FFFFFC18h (2’s complement of 3E8h)
Positive
Negative
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
37
MIDI Implementation Chart
TransmittedFunction... Recognized Remarks
Basic
Channel
Note
Number : True voice
Velocity
After
Touch
Pitch Bend
Control
Change
Prog
Change : True #
System Exclusive
: Song Pos.
Common : Song Sel.
: Tune
System : Clock
Real Time : Commands
: All Sound Off
Aux :
Reset
All
Cntrls
: Local ON/OFF
Mes- : All Notes OFF
sages: Active Sense
: Reset
Notes:
Mode
Default
Changed
Note ON
Note OFF
Key's
Ch's
0,32
1-31,33-95,102-119
1 - 16
1 - 16
˛
˛
˛
˛
Ø
*1
Ø *2
Ø 0 - 127 *1
**************
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
*1 transmit/receive if program change switch is on.
*2 transmit/receive if control change switch is on.
*3 transmit/receive if parameter change switch is on.
˛
˛
**************
˛
**************
Ø *3
Mode 1 : OMNI ON , POLY Mode 2 : OMNI ON ,MONO
Mode 3 : OMNI OFF, POLY Mode 4 : OMNI OFF,MONO
˛
1 - 16
1 - 16
˛
˛
˛
˛
Ø
*1
Ø *2
˛
˛
˛
˛
˛
˛
˛
˛
˛
Ø
˛
˛
˛
˛
˛
˛
Ø
*3
˛
Ø
: Yes
˛ : No
Default
Messages
Altered
YAMAHA [Digital Mixing Engine Satellite] Date :14-FEB-2007
Model DME8i-ES, DME8o-ES, DME4io-ES MIDI Implementation Chart
Version : 1.0
Memorized
Bank Select
Assignable
Assignable
Ø 0 - 127 *1
0 - 127
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
References
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
38
Display Messages
The [ERROR] and [PEAK] indicators on the front panel of the DME Satellite indicate error and warning messages.
Error Messages
Warning Messages
Indicator Error Action
A system error has occurred. Execute the “Initialize DME” operation, then restart it. If the error
indicators are still indicating the error, execute the “Delete All Data”
initialization. If the problem persists, contact a Yamaha dealer.
Data inside the internal flash
memory has been erased.
The firmware update operation may have failed. Use DME Designer
to execute the Recovery update operation. If the problem persists,
contact a Yamaha dealer.
The internal battery is
completely discharged or not
installed.
If you turn off the power to the unit, the current settings will be lost
and reset to the default values. Stop operating the unit, and contact a
Yamaha dealer regarding battery replacement.
A scene recall attempt has
failed.
Use DME Designer to recall the scene again.
If the problem persists, contact a Yamaha dealer.
Audio is not input or output and
is muted due to insufficient DSP
resources.
This error sometimes occurs if you try to operate a configuration at 96
kHz that has been created with a word clock of 48 kHz. To operate a
configuration at any word clock setting, use DME Designer to create
a configuration with the word clock set to 96 kHz.
The network is not
communicating properly.
Connect the Ethernet cables properly, and make sure that the
network devices are operating correctly.
Duplicate IP addresses. Connect your computer to the DME Satellite via USB, then set a
unique IP address.
The DME Satellite contains data
for a different device group or
no data.
Send data appropriate for the actual device configuration from DME
Designer.
Indicator Error Action
The internal battery is almost
discharged. Your data may be
lost.
If you turn off the power to the unit, the current settings may
be lost and reset to the default values. Stop operating the
unit, and contact a Yamaha dealer regarding battery
replacement.
The backup battery voltage is
low.
This does not affect the operation of the unit. However, if you
continue using the unit, the settings may be lost and reset to
the default values. Contact a Yamaha dealer regarding
battery replacement at your earliest convenience.
Flashing
Lit
Flashing
Lit
Flashing
Lit
Flashing
Lit
Lit
Flashing
Flashing
Lit
Flashing
Lit
Flashing
Lit
Flashing
rapidly
Flashing
slow
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
References
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
39
General Specifications
Electrical Characteristics
Output impedance of signal generator: 150
DME8i-ES : Measured with DME8o-ES
DME8o-ES : Measured with DME8i-ES
DME4io-ES: Measured with DME4io-ES
Frequency Response fs=48kHz@20Hz–20kHz, reference to the nominal output level @1kHz
fs=96kHz@20Hz–40kHz, reference to the nominal output level @1kHz
<DME8i-ES>
<DME8o-ES>
<DME4io-ES>
Gain Error @1kHz
<DME8i-ES>
Sampling Frequency
External Clock
Normal Rate: 44.1/48 kHz (±0.1%)
Double Rate: 88.2/96 kHz (±0.1%)
Internal Clock
Normal Rate: 48 kHz (±50ppm)
Double Rate: 96 kHz (±50ppm)
Maximum Voltage Gain
Gain: –60dB, RL:600, 64dB INPUT to OUTPUT
Miscellaneous
Power Consumption 40W
Dimensions (HxDxW) 44x361x480 mm
Net Weight 4.5kg
Temperature range
operating: 5 to 40˚C
storage: –20 to 60˚C
Include Accessories
AC Power cord, Mini Euro plug(16P)x1, Euro plug(3P)x8, Owner’s Manual,
Rubber feetx4
Input Output RL CONDITIONS MIN TYP MAX UNITS
INPUT 1–8 OUTPUT 1–8 600
input level: –60dBu, GAIN: –60dB –1.5 0.0 +0.5 dB
input level: +10dBu, GAIN: +10dB –1.5 0.0 +0.5 dB
Input Output RL CONDITIONS MIN TYP MAX UNITS
INPUT 1–8 OUTPUT 1–8 600 input level: +10dBu, GAIN: +10dB –1.5 0.0 +0.5 dB
Input Output RL CONDITIONS MIN TYP MAX UNITS
INPUT 1–4 OUTPUT 1–4 600
input level: –60dBu, GAIN: –60dB –1.5 0.0 +0.5 dB
input level: +10dBu, GAIN: +10dB –1.5 0.0 +0.5 dB
Input Output RL CONDITIONS MIN TYP MAX UNITS
INPUT 1–8 OUTPUT 1–8 600
input level: –60dBu, GAIN: –60dB
output level: +4.0dBu (typ.)
–2.0 0 +2.0 dB
input level: +10dBu, GAIN: +10dB
output level: +4.0dBu (typ.)
–2.0 0 +2.0 dB
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
References
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
40
<DME8o-ES>
<DME4io-ES>
Total Harmonic Distortion fs=48kHz or 96kHz
<DME8i-ES>
<DME8o-ES>
<DME4io-ES>
Input Output RL CONDITIONS MIN TYP MAX UNITS
INPUT 1–8 OUTPUT 1–8 600
input level: +10dBu, GAIN: +10dB
output level: +4.0dBu (typ.)
–2.0 0 +2.0 dB
Input Output RL CONDITIONS MIN TYP MAX UNITS
INPUT 1–4 OUTPUT 1–4 600
input level: –60dBu, GAIN: –60dB
output level: +4.0dBu (typ.)
–2.0 0 +2.0 dB
input level: +10dBu, GAIN: +10dB
output level: +4.0dBu (typ.)
–2.0 0 +2.0 dB
Input Output RL CONDITIONS MIN TYP MAX UNITS
INPUT 1–8 OUTPUT 1–8 600
+4dB@20Hz–20kHz (fs=48kHz),
20Hz–40kHz (fs=96kHz), GAIN: –60dB
0.1 %
+4dB@20Hz–20kHz (fs=48kHz),
20Hz–40kHz (fs=96kHz), GAIN: +10dB
0.05 %
+22dB@1kHz, GAIN: +10dB
0.015
(fs=48kHz)
0.007
(fs=96kHz)
%
Input Output RL CONDITIONS MIN TYP MAX UNITS
INPUT 1–8 OUTPUT 1–8 600
+4dB@20Hz–20kHz (fs=48kHz),
20Hz–40kHz (fs=96kHz), GAIN: +10dB
0.05 %
+22dB@1kHz, GAIN: +10dB
0.015
(fs=48kHz)
0.007
(fs=96kHz)
%
Input Output RL CONDITIONS MIN TYP MAX UNITS
INPUT 1–4 OUTPUT 1–4 600
+4dB@20Hz–20kHz (fs=48kHz),
20Hz–40kHz (fs=96kHz), GAIN: –60dB
0.1 %
+4dB@20Hz–20kHz (fs=48kHz),
20Hz–40kHz (fs=96kHz), GAIN: +10dB
0.05 %
+22dB@1kHz, GAIN: +10dB
0.015
(fs=48kHz)
0.007
(fs=96kHz)
%
* Total Harmonic Distortion is measured with a 18dB/octave filter @80kHz.
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
References
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
41
Hum&Noise fs=48kHz or 96kHz, EIN=Equivalent Input Noise
<DME8i-ES>
<DME8o-ES>
<DME4io-ES>
Dynamic Range fs=48kHz or 96kHz
<DME8i-ES/DME8o-ES>
<DME4io-ES>
Crosstalk@1kHz reference to the level of output N
<DME8i-ES/DME8o-ES>
<DME4io-ES>
Input Output RL CONDITIONS MIN TYP MAX UNITS
INPUT 1–8 OUTPUT 1–8 600
Rs=150, GAIN: –60dB
All input & output level controls: 0dB
–128
EIN
–127
EIN
dBu
–64 dBu
Rs=150, GAIN: +10dB
All input & output level controls: 0dB
–82 –79 dBu
Input Output RL CONDITIONS MIN TYP MAX UNITS
INPUT 1–8 OUTPUT 1–8 600
Rs=150, GAIN: +10dB
All input & output level controls: 0dB
–82 –79 dBu
Input Output RL CONDITIONS MIN TYP MAX UNITS
INPUT 1–4 OUTPUT 1–4 600
Rs=150, GAIN: –60dB
All input & output level controls: 0dB
–128
EIN
–127
EIN
dBu
–64 dBu
Rs=150, GAIN: +10dB
All input & output level controls: 0dB
–82 –79 dBu
* Hum & Noise are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave
attenuation.
Input Output RL CONDITIONS MIN TYP MAX UNITS
INPUT 1–8 OUTPUT 1–8 600 GAIN: +10dB 106 dB
Input Output RL CONDITIONS MIN TYP MAX UNITS
INPUT 1–4 OUTPUT 1–4 600 GAIN: +10dB 106 dB
* Dynamic range are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave
attenuation.
from to CONDITIONS MIN TYP MAX UNITS
INPUT N OUTPUT (N–1) or (N+1) N = 1–8, GAIN: +10dB –80 dB
from to CONDITIONS MIN TYP MAX UNITS
INPUT N OUTPUT (N–1) or (N+1) N = 1–4, GAIN: +10dB –80 dB
*Crosstalk is measured with a 18dB/octave filter @80kHz
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
References
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
42
LED Level Meter
<DME8i-ES>
<DME8o-ES>
<DME4io-ES>
Signal Delay
Input/Output Characteristics
ANALOG INPUT CHARACTERISTICS
ANALOG OUTPUT CHARACTERISTICS
DIGITAL INPUT & OUTPUT CHARACTERISTICS
METERING POINT CONDITIONS MIN TYP MAX UNITS
INPUT 1–8
PEAK red LED: ON –3 dBFs
SIGNAL green LED: ON –40 dBFs
METERING POINT CONDITIONS MIN TYP MAX UNITS
OUTPUT 1–8
PEAK red LED: ON –3 dBFs
SIGNAL green LED: ON –40 dBFs
METERING POINT CONDITIONS MIN TYP MAX UNITS
INPUT 1–4
OUTPUT 1–4
PEAK red LED:ON –3 dBFs
SIGNAL green LED:ON –40 dBFs
from to CONDITIONS MIN TYP MAX UNITS
Analog input of Primary Master Analog output of the slave via EtherSound @ 48kHz 2 msec
Input Terminals GAIN Actual Load
Impedance
For Use With
Nominal
Input Level Connector
Nominal Max.before clip
<DME8i-ES>
CH INPUT 1–8
<DME4io-ES>
CH INPUT 1–4
–60dB
3k
50–600 Mics &
600 Lines
–60dBu
(0.775mV)
–40dBu
(7.75mV)
EUROBLOCK
(5.08mm pitch)
+10dB
+10dBu
(2.45V)
+30dBu
(24.5V)
*1.In these specifications, 0dBu is referenced to 0.775 Vrms.
*2.All AD converters are 24-bit linear, 128-times oversampling (Fs=48kHz)/64-times oversampling (Fs=96kHz).
*3.+48V DC (Phantom power) is supplied to CH INPUT EUROBLOCK connectors via each individual software
controlled switch.
Output Terminals Actual Source
Impedance
For Use With
Nominal
Output level Connector
Nominal Max. before clip
<DME8o-ES>
CH OUTPUT 1–8
<DME4io-ES>
CH OUTPUT 1–4
75 600 Lines +4dBu (1.23 V) +24dBu(12.28V)
EUROBLOCK
(5.08mm pitch)
*1.In these specifications, 0dBu is referenced to 0.775 Vrms.
*2.All DA converters are 24-bit linear, 128-times oversampling (Fs=48kHz)/64-times oversampling (Fs=96kHz).
Terminal Format Data length Level Audio Connector
EtherSound EtherSound 24bit 100Base-TX
16ch input/16ch output @ 48kHz
8ch input/8ch output @ 96kHz
RJ-45x2
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
References
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
43
CONTROL I/O CHARACTERISTICS
[NETWORK] Connector (100Base-TX Ethernet, RJ-45)
Terminal Format Level Connector
GPI
IN 0–5V
EUROBLOCK *1
(3.5mm pitch)
OUT TTL
+V 5V
Ethernet IEEE802.3 10Base-T/100Base-TX RJ-45
USB USB 1.1 Function Type B
REMOTE RS-232C/RS-422 RS-232C/RS-422 D-SUB 9P (Male)
*1 Inputs: 8 channels, Outputs: 4 channels
Inputs: Not apply 2 wire Fader mode
Outputs: Imax/pin = 16mA
Outputs: VH = 2.5V(min.), VL = 0.6V(max.)
Pin Connection
1 TxD+
2 TxD–
3 RxD+
4 Unused
5 Unused
6 RxD–
7 Unused
8 Unused
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
References
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
44
Dimensions
* Specifications and descriptions in this owner’s manual are for information purpose only. Yamaha Corp. reserves the right to
charge or modify products or specifications at any time without prior notice. Since specifications, equipment or options may
not be the same in every locale, please check with your Yamaha dealer.
European models
Purchaser/User Information specified in EN55103-1 and EN55103-2.
Inrush Current: 35A
Conforms to Environments: E1,E2,E3 and E4.
440
480
3
1
44
361
354
(4)
Rubber feet
are included in
the package.
Unit: mm
References
Other Functions
Connecting to an
External Device
Audio I/O
Connection
Connecting to
a Computer
Controls and
Connectors
Introduction to
the DME Satellite
Foreword
References
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
45
Index
A
About DME Designer ........................13
[AC IN] Connector ............................16
Analog Audio Connection ..................25
area ......................................................9
C
Components ........................................9
Configuration .......................................9
CP4SW, CP4SF, and CP1SF .............32
D
Delete All Data ..................................31
device group .........................................9
Digital Audio Connection ..................24
Dimensions ........................................44
Dip Switch .........................................16
Display Messages ................................38
DME4io-ES .........................................8
DME8i-ES ...........................................8
DME8o-ES ..........................................8
E
Electrical Characteristics .....................39
[ERROR] Indicator ............................15
Error Messages ...................................38
Ethernet Connection ..........................20
EtherSound Connection .....................28
EtherSound Connectors ...............24, 28
EtherSound [IN]/[OUT] Connectors 17
Euroblock plug connection ................25
F
Firmware Version .................................7
G
General Specifications ........................39
GPI Connection .................................30
[GPI] Connector ................................17
Ground Screw ....................................16
group master ........................................9
I
ICP1 ..................................................32
Initialize DME ...................................31
Initializing ..........................................31
[INPUT] & [OUTPUT] Connectors 25
[INPUT] Connectors .........................17
Input/Output Characteristics .............42
M
Master and slave setting ..................... 19
[MASTER] Indicator ........................ 14
MIDI Data Format ........................... 34
MIDI Implementation Chart ............ 37
N
[NETWORK] Connector ........... 16, 43
[NETWORK] Indicator .................... 14
Network Settings ............................... 19
O
octet .................................................. 19
Options ............................................. 32
[OUTPUT] Connectors .................... 17
P
parameters ........................................... 9
[PEAK] Indicators ............................. 15
[POWER] Indicator .......................... 15
[POWER] Switch .............................. 15
Precautions for Using a Rack-mounted
DME Satellite ............................. 17
preset parameters ................................. 9
R
Remote Connection .......................... 26
[REMOTE] Connector ..................... 17
RS-232C ........................................... 16
RS-422 .............................................. 16
S
Scene ................................................. 10
Setting the IP address ........................ 19
[SIGNAL] Indicators ......................... 15
Signal Types ...................................... 11
Straight and Crossover Cable Wiring 44
System Examples ............................... 12
T
Troubleshooting ................................ 33
[TX/RX] Indicator ............................ 15
U
USB Connection ............................... 18
[USB] Connector .............................. 14
User Defined buttons (User Defined
parameters) ................................... 9
W
Warning Messages ............................. 38
Z
zones ................................................... 9
Foreword
Introduction to
the DME Satellite
Controls and
Connectors
Connecting to
a Computer
Audio I/O
Connection
Connecting to an
External Device
Other Functions
References
DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual
46
MEMO
For details of products, please contact your nearest Yamaha
representative or the authorized distributor listed below.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou
au distributeur le plus proche de vous figurant dans la liste suivante.
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Para detalles sobre productos, contacte su tienda Yamaha más cercana
o el distribuidor autorizado que se lista debajo.
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Scarborough, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Ave., Buena Park, Calif. 90620,
U.S.A.
Tel: 714-522-9011
MEXICO
Yamaha de México S.A. de C.V.
Calz. Javier Rojo Gómez #1149,
Col. Guadalupe del Moral
C.P. 09300, México, D.F., México
Tel: 55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi,
CEP 04534-013 Sao Paulo, SP. BRAZIL
Tel: 011-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.
Sucursal de Argentina
Olga Cossettini 1553, Piso 4 Norte
Madero Este-C1107CEK
Buenos Aires, Argentina
Tel: 011-4119-7000
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso 7, Urbanización Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, Panamá
Tel: +507-269-5311
THE UNITED KINGDOM
Yamaha Music U.K. Ltd.
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, England
Tel: 01908-366700
GERMANY
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH
Branch Switzerland in Zürich
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 01-383 3990
AUSTRIA
Yamaha Music Europe GmbH Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
CZECH REPUBLIC/SLOVAKIA/
HUNGARY/SLOVENIA
Yamaha Music Europe GmbH Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-602039025
POLAND
Yamaha Music Europe GmbH
Branch Sp.z o.o. Oddzial w Polsce
ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland
Tel: 022-868-07-57
THE NETHERLANDS/
BELGIUM/LUXEMBOURG
Yamaha Music Europe Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen, The Netherlands
Tel: 0347-358 040
FRANCE
Yamaha Musique France
BP 70-77312 Marne-la-Vallée Cedex 2, France
Tel: 01-64-61-4000
ITALY
Yamaha Musica Italia S.P.A.
Combo Division
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
SPAIN/PORTUGAL
Yamaha Música Ibérica, S.A.
Ctra. de la Coruna km. 17, 200, 28230
Las Rozas (Madrid), Spain
Tel: 91-639-8888
SWEDEN
Yamaha Scandinavia AB
J. A. Wettergrens Gata 1, Box 30053
S-400 43 Göteborg, Sweden
Tel: 031 89 34 00
DENMARK
YS Copenhagen Liaison Office
Generatorvej 6A, DK-2730 Herlev, Denmark
Tel: 44 92 49 00
NORWAY
Norsk filial av Yamaha Scandinavia AB
Grini Næringspark 1, N-1345 Østerås, Norway
Tel: 67 16 77 70
RUSSIA
Yamaha Music (Russia)
Room 37, bld. 7, Kievskaya street, Moscow, 121059,
Russia
Tel:495 626 5005
OTHER EUROPEAN COUNTRIES
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
Yamaha Corporation,
Asia-Pacific Sales & Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2303
TURKEY/CYPRUS
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
OTHER COUNTRIES
Yamaha Music Gulf FZE
LOB 16-513, P.O.Box 17328, Jubel Ali,
Dubai, United Arab Emirates
Tel: +971-4-881-5868
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
Shanghai, China
Tel: 021-6247-2211
INDIA
Yamaha Music India Pvt. Ltd.
5F Ambience Corporate Tower Ambience Mall Complex
Ambience Island, NH-8, Gurgaon-122001, Haryana, India
Tel: 0124-466-5551
INDONESIA
PT. Yamaha Music Indonesia (Distributor)
PT. Nusantik
Gedung Yamaha Music Center, Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 21-520-2577
KOREA
Yamaha Music Korea Ltd.
8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,
Kangnam-Gu, Seoul, Korea
Tel: 080-004-0022
MALAYSIA
Yamaha Music Malaysia, Sdn., Bhd.
Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,
Petaling Jaya, Selangor, Malaysia
Tel: 3-78030900
SINGAPORE
Yamaha Music Asia Pte., Ltd.
#03-11 A-Z Building
140 Paya Lebor Road, Singapore 409015
Tel: 747-4374
TAIWAN
Yamaha KHS Music Co., Ltd.
3F, #6, Sec.2, Nan Jing E. Rd. Taipei.
Taiwan 104, R.O.C.
Tel: 02-2511-8688
THAILAND
Siam Music Yamaha Co., Ltd.
4, 6, 15 and 16
th
floor, Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
Tel: 02-215-2626
OTHER ASIAN COUNTRIES
Yamaha Corporation,
Asia-Pacific Sales & Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2303
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Tel: 3-9693-5111
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation,
Asia-Pacific Sales & Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2303
NORTH AMERICA
CENTRAL & SOUTH AMERICA
EUROPE
AFRICA
MIDDLE EAST
ASIA
OCEANIA
HEAD OFFICE
Yamaha Corporation, Pro Audio Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2441
PA26'
008IPTO-D0
Yamaha Manual Library
http://www.yamaha.co.jp/manual/
Yamaha Pro Audio global web site:
http://www.yamahaproaudio.com/
© 2007-2010 Yamaha Corporation
U.R.G., Pro Audio Division
Printed in Japan
WK01190

Transcripción de documentos

DIGITAL MIXING ENGINE SATELLITE Owner’s Manual EN Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the top of the unit. IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 8 9 10 Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 12 13 14 Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. (98-6500) This product contains a battery that contains perchlorate material. Perchlorate Material—special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (Perchlorate) FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party : Yamaha Corporation of America Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620 Telephone : 714-522-9011 Type of Equipment : DIGITAL MIXING ENGINE SATELLITE Model Name : DME8i-ES/DME8o-ES/DME4io-ES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B) ADVARSEL! Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. VARNING Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. VAROITUS Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. (lithium caution) (FCC DoC) NEDERLAND / THE NETHERLANDS • Dit apparaat bevat een lithium batterij voor geheugen back-up. • This apparatus contains a lithium battery for memory back-up. • Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het apparaat ann het einde van de levensduur of gelieve dan contact op te nemen met de vertegenwoordiging van Yamaha in uw land. • For the removal of the battery at the moment of the disposal at the end of life please consult your retailer or Yamaha representative office in your country. • Gooi de batterij niet weg, maar lever hem in als KCA. • Do not throw away the battery. Instead, hand it in as small chemical waste. (lithium disposal) IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT. The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or colored GREEN or GREEN-andYELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. • This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.(3 wires) PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply/Power cord Water warning • Only use the voltage specified as correct for the device. The required voltage is printed on the name plate of the device. • Do not expose the device to rain, use it near water or in damp or wet conditions, or place containers on it containing liquids which might spill into any openings. • Use only the included power cord. If you intend to use the device in an area other than in the one you purchased, the included power cord may not be compatible. Please check with your Yamaha dealer. • Never insert or remove an electric plug with wet hands. • Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it. • If the power cord or plug becomes frayed or damaged, or if there is a sudden loss of sound during use of the device, or if any unusual smells or smoke should appear to be caused by it, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel. • Be sure to connect to an appropriate outlet with a protective grounding connection. Improper grounding can result in electrical shock. If you notice any abnormality • If this device should be dropped or damaged, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel. Do not open • Do not open the device or attempt to disassemble the internal parts or modify them in any way. The device contains no user-serviceable parts. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel. CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire. Power supply/Power cord • Remove the electric plug from the outlet when the device is not to be used for extended periods of time, or during electrical storms. • If several of the devices are mounted in an EIA-compliant rack, carefully read the section “Precautions for Using a Rack-mounted DME Satellite” on page 17 • When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it. • Avoid setting all equalizer controls and faders to their maximum. Depending on the condition of the connected devices, doing so may cause feedback and may damage the speakers. Location • Before moving the device, remove all connected cables. • When setting up the device, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product all the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. • If this device is to be mounted in an EIA-standard rack, leave the back of the rack open and make sure that it is at least 10 cm away from walls or surfaces. Also, if this device is to be mounted with devices that tend to generate heat, such as power amplifiers, be sure to keep an adequate gap between this device and the heat-generating devices or install ventilation panels to prevent high temperatures from developing inside this device. (5)-4 4 DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual • Do not expose the device to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components. • Do not place the device in an unstable position where it might accidentally fall over. • Do not block the vents. This device has ventilation holes at the rear to prevent the internal temperature from becoming too high. In particular, do not place the device on its side or upside down. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire. • Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Doing so may result in noise, both in the device itself and in the TV or radio next to it. 1/2 Connections Backup battery • Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. Handling caution • Do not insert your fingers or hands in any gaps or openings on the device. • Condensation can occur in the device due to rapid, drastic changes in ambient temperature—when the device is moved from one location to another, or air conditioning is turned on or off, for example. Using the device while condensation is present can cause damage. If there is reason to believe that condensation might have occurred, leave the device for several hours without turning on the power until the condensation has completely dried out. • Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any gaps or openings on the device. If this happens, turn off the power immediately and unplug the power cord from the AC outlet. Then have the device inspected by qualified Yamaha service personnel. • This device has a built-in backup battery that maintains data in internal memory even when the device’s power is switched off. The backup battery will eventually become depleted, however, and when that happens the contents of the internal memory will be lost.* To prevent loss of data be sure to replace the backup battery before it becomes fully depleted. When the backup battery charge becomes low, the [ERROR] indicator on the front panel blinks (For details, refer to “Error Messages” on page 38). In this case, do not turn off the power and immediately transfer any data you want to save to a computer or other external storage device, then have qualified Yamaha service personnel replace the backup battery. The average life of the internal backup battery is approximately 5 years, depending on operating conditions. * Data items maintained in the internal memory by the backup battery are as follows: • Current scene parameters and number. • Device parameters (HA, UTILITY, Master Mute/Level, etc.). • Do not use the device for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. • Event log. Data items other than those described above are stored in memory that does not require backup power, and will be retained even if the backup battery fails. • Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on the buttons, switches or connectors. Do not turn the [POWER] switch on and off repeatedly and rapidly. Be sure to wait six seconds or more between turning the power to the unit off and then on. The rubber feet included in this package can be attached to the speaker to prevent slippage when it is to be used on a slipper y surface. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed. Always turn the power off when the device is not in use. The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualifi ed Yamaha service personnel about replacing defective components. • Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal use. • The illustrations in this owner’s manual are for instructional purposes, and may appear somewhat different from the actual equipment. • EtherSound is a trademark of Digigram SA. • Ethernet is a trademark of Xerox Corporation. • All other trademarks are the property of their respective holders and are hereby acknowledged. (5)-4 2/2 DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 5 Foreword Contents Introduction to the DME Satellite Foreword .......................................... 7 Connecting to an External Device............. 26 Accessories (Please make sure the following items are included in the package.)................................ Options........................................................................... About the Product Names............................................... About the Firmware Version ........................................... Preparation...................................................................... Remote Connection ([REMOTE] Connector).............. 26 Controls and Connectors 7 7 7 7 7 EtherSound Connection (EtherSound Connectors)....... 28 Connecting the AC power cord........................................... 7 Turning the power on and off ............................................. 7 Controlling DME Satellite’s internal head amps from a digital mixer .......................................................... 28 Introduction to the DME Satellite .............. 8 Network Connection ([NETWORK] Connectors) ....... 29 GPI Connection ([GPI] Connector).............................. 30 Connecting to a Computer Differences between DME8i-ES, DME8o-ES, and DME4io-ES ............................................ 8 DME Satellite Features ................................................... 8 Audio System Network ................................................... 9 Glossary for the DME Satellite........................................ 9 Signal Types.................................................................. 11 System Examples........................................................... 12 About DME Designer ................................................... 13 Audio I/O Connection Controls and Connectors ....................... 14 Front Panel ................................................................... Caution when turning the power off ............................. Rear Panel ..................................................................... Precautions for Using a Rack-mounted DME Satellite .. 14 15 16 17 Other Functions.................................. 31 Initializing the DME Satellite........................................ 31 References ....................................... 32 Options ......................................................................... 32 ICP1.................................................................................. 32 CP4SW, CP4SF, and CP1SF............................................. 32 Troubleshooting ............................................................ 33 Component ................................................................... 33 MIDI Data Format ....................................................... 34 1. MIDI functions on the DME8i-ES, DME8o-ES, and DME4io-ES ................................................... 34 2. MIDI Data Flow ........................................................... 34 3. MIDI Setup................................................................... 34 4. MIDI Format ................................................................ 35 Connecting to an External Device Connecting to a Computer ..................... 18 MIDI Implementation Chart ........................................ 37 Display Messages........................................................... 38 USB Connection........................................................... 18 Error Messages................................................................... 38 Warning Messages ............................................................. 38 Network Settings............................................................... 19 Ethernet Connection ([NETWORK] Connector)......... 20 Audio I/O Connection ........................... 24 Other Functions Digital Audio Connection (EtherSound Connectors).... 24 Analog Audio Connection ([INPUT] & [OUTPUT] Connectors) ................................................. 25 References 6 Controlling external head amplifiers from the DME Satellite ................................................................. 26 Controlling a DME Satellite’s internal head amps from a digital mixer .......................................................... 27 Controlling the DME Satellite from an external device...... 27 DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual General Specifications ................................................... Electrical Characteristics ................................................ Input/Output Characteristics ........................................ [NETWORK] Connector (100Base-TX Ethernet, RJ-45) .......................................................... Dimensions ................................................................... Index ............................................................................. 39 39 42 43 44 45 Foreword Thank you for choosing a Yamaha DME8i-ES/DME8o-ES/DME4io-ES Digital Mixing Engine Satellite. In order to take full advantage of the features and performance provided by the DME8i-ES/DME8o-ES/DME4io-ES, we urge you to read this owner’s manual thoroughly before connecting or using the unit. Keep this manual in a safe place for future reference. Options Control Panels • ICP1 Intelligent Control Panel • CP4SW Control Panel • CP4SF Control Panel • CP1SF Control Panel NOT E For more information on your Control Panel, refer to the owner’s manual that came with the Control Panel, as well as the DME Designer Owner’s Manual. Turning the power on and off CAUTION To prevent the initial power-on surge from generating a large noise spike or damaging your speaker system, turn the devices on in the following order: audio sources, mixer (such as M7CL or PM5D), DME Satellite, and finally power amplifiers. Reverse this order when turning power off. 1. Press the [POWER] switch to turn on the In this manual, models DME8i-ES, DME8o-ES, and DME4io-ES are all called “DME Satellite,” and models DME64N and DME24N, DME8i-C/DME8o-C/ DME4io-C and the DME Satellite are categorized as the DME series. About the Firmware Version You can check the version number of the DME Satellite firmware by using the DME Designer application software. You can also download the latest firmware from the following Yamaha website. http://www.yamahaproaudio.com/downloads/ Controls and Connectors power to the DME Satellite. 2. Press the [POWER] switch again to turn off About the Product Names Connecting to a Computer First plug the female-connector end of the AC cord into the [AC IN] socket on the rear panel of the DME Satellite, then plug the male plug into an appropriate AC mains outlet. Be sure to use the voltage specified for the device. Audio I/O Connection CAUTION Be sure to turn all devices OFF before connecting AC mains power. the power. NOTE The DME Satellite remembers scene settings when you turn off the power. When you turn on the power to the DME Satellite, it will start up with the same scene settings. You can use the “Last Mem. Resume” setting in DME Designer to set up the DME Satellite so that at the startup it will recall the scene selected before you turned off the power to the device. CAUTION • Do NOT turn off the power to the DME Satellite while it is receiving data from DME Designer or while it is being manipulated from an external device. Otherwise, a malfunction may occur. • Even when the power switch is turned off, electricity is still flowing to the product all the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual Connecting to an External Device • • • • DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual (this document) AC power cord Euroblock plug (16P) x 1 Euroblock plug (3P) x 8 Rubber feet x 4 Connecting the AC power cord Other Functions • Preparation References Accessories (Please make sure the following items are included in the package.) Introduction to the DME Satellite Foreword 7 Foreword Introduction to the DME Satellite Differences between DME8i-ES, DME8o-ES, and DME4io-ES Introduction to the DME Satellite The differences between these three models are as follows: ■ DME8i-ES This model features 8-channel analog inputs. ■ DME8o-ES This model features 8-channel analog outputs. Controls and Connectors ■ DME4io-ES This model features 4-channel analog inputs and 4-channel analog outputs. DME Satellite Features Connecting to a Computer In addition to basic mixing and matrix output functions, the DME Satellite includes a equalizers, compressors, delay, etc. – that can be patched together via DME Designer to configure just about any audio system you need. The EtherSound connectors on the device enable you to remotely control analog inputs and outputs by transferring digital audio signals via a network. The following steps summarize the process for setting up the DME Satellite for use: (For details, refer to the “DME Setup Manual”.) Audio I/O Connection 1. Install USB-MIDI Driver, DME Designer and DME-N Network Driver. 2. Set up the network from DME Designer (page 19). 3. Connect devices. Connecting to an External Device Other Functions • Network connection Ethernet connection (page 20) USB connection (page 18) • EtherSound connection (page 28) In order to route inputs and outputs, you’ll need the “AVS-ESMonitor” application software made by the AuviTran SARL. You can download this from the following website. http://www.auvitran.com/view.php?products_AVS-ESMonitor.php • Analog connection (page 25) • External device connection Remote connection (page 26) GPI connection (page 30) 4. Make network settings on your computer. 5. Create a configuration using DME Designer, then transfer it to the DME Satellite. References 8 DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual Foreword Introduction to the DME Satellite Glossary for the DME Satellite This section explains terminology specific to the DME Satellite. Controls and Connectors Multiple DME series units that are interconnected in a network via Ethernet function as a single audio system. In a DME audio system, a group of the same models that can be operated in sync is called a “device group;” audio processing divisions that accommodate multiple device groups are called “zones;” and the entire area serviced by the acoustic system is called an “area.” Each device group always includes one DME series unit that functions as the “group master” and controls all other DME series units in the same device group. If a computer is connected to the network, you can use the computer to control an entire device group via the group master. Introduction to the DME Satellite Audio System Network A “configuration” is a complete set of components for constructing an audio system. Each configuration determines the audio function(s) of the corresponding DME Satellite unit. All parameter sets included with each component in a configuration are called “preset parameters.” One DME Satellite unit has a number of configurations, and a configuration has a number of preset parameters. User Defined buttons (User Defined parameters) References Other Functions Connecting to an External Device Assigning parameters to be User Defined parameters enables you to control the device from the ICP1 and the DME64N/DME24N. Refer to the “DME Designer Owner’s Manual” for details. Audio I/O Connection Configuration Connecting to a Computer Components and parameters The individual audio processing modules (equalizers, compressors, etc.) are called “components.” External head amplifier control modules are also available as components. Changing the parameters of components enables control over the operation of the components. DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 9 Foreword Introduction to the DME Satellite Scene Introduction to the DME Satellite A combination of all configuration and preset parameters is called a “scene.” Scenes can be recalled from an ICP1, GPI device, other external controllers, DME64N/DME24N, or computer. Up to 999 scenes can be stored for each device group. Scene structure Scene Preset Parameter Configuration Matrix Mixer Scene 1 Ex.: Gate • Attack • Decay • Range • Threshold • Key in • Hold Scene 2 Controls and Connectors 16 x 8 Scene 999 Component Scene change Connecting to a Computer First Act Band Set Play Set Audio I/O Connection Band Set Second Act Play Set Play Set Band Set Stage Stage Stage Scene 1 Scene Recall Scene 2 Connecting to an External Device Other Functions References 10 Dark Change DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual Foreword Introduction to the DME Satellite Signal Types 3 Control signals between devices outside the device group These signals provide communication and control between individual devices. Included in this category are MIDI messages transferred between [USB] connectors, GPI signals transferred between [GPI] connectors, and remote head amp control signals handled via the [REMOTE] connector. Type of signals handled by the DME Satellite [USB] Connector [NETWORK] Connector EtherSound Connector [GPI] Connector [REMOTE] Connector [INPUT]/[OUTPUT] Connectors (audio in/out) Device Control Reference Page — • Control signals between computer and DME Satellite • MIDI messages page 18 — • Control signals between computer and DME Satellite • Control signals between DME Satellites • Control signals with a controller such as an AMX or Crestron page 20 page 29 • Internal head amp control signals with a digital mixer • Control signals with AVS-ESMonitor page 24 page 28 — GPI control signals between GPI device (GPI controller, etc.) and DME series unit page 30 — • Control signals to/from an external device (such as AD8HR head amplifier) • Control signals for a digital mixer and internal head amp • Control signals with a controller such as an AMX or Crestron • MIDI messages page 26 Audio Signal Up to 16 channels of input and output. The number of I/O channels depends on model. — page 25 References Connector Controls and Connectors Control signals within a device group Connecting to a Computer 2 Device group control signals control all DME series devices in the group. There are two types of device group control signals, as follows: • Control signals between the computer and the group master DME series unit • Control signals between the group master DME series unit and the other DME series units You can use the DME Designer application to control the entire device group, such as sending components to the devices and setting the parameters as required. Audio I/O Connection Analog and digital signals are input and output between the DME Satellite, other DME series units, and other audio devices. Analog signals are input and output via the [INPUT]/[OUTPUT] jacks. Digital signals are input and output via the EtherSound jacks. Connecting to an External Device Audio Other Functions 1 Introduction to the DME Satellite DME Satellite audio system signals can be broadly categorized as follows. DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 11 Foreword Introduction to the DME Satellite System Examples Multiple DME Satellite units: Large-scale system Introduction to the DME Satellite Space B Space A DME8i-ES Computer Analog In ICP1 DME8i-ES Controls and Connectors Hub DME4io-ES Analog In Analog In Analog Out Hub Connecting to a Computer M7CL Space C DME8o-ES EtherSound compatible I/O card × 2 Analog Out DME8o-ES Audio I/O Connection Primary Master Analog Out Hub DME8o-ES Analog Out Connecting to an External Device Space D DME8i-ES Other Functions DME4io-ES Analog In Analog In Analog Out Hub DME8o-ES EtherSound Ethernet Control Analog Out Analog Audio References N OT E • Connect the computer to the [IN] connector of the first daisy-chained EtherSound device. This connector can also be used in common with the same network as Ethernet Control. • Units following the [OUT] connector of the first EtherSound device cannot be used in common with the same network as Ethernet Control. 12 DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual Foreword Introduction to the DME Satellite Controls and Connectors Connecting to a Computer References Other Functions Connecting to an External Device Audio I/O Connection DME Designer software enables you to integrate, configure, and control the DME series system from a connected computer. You can build the DME series audio system using graphic blocks in DME Designer that are displayed on the computer monitor. The DME series settings, configuration, and parameter data are transferred from the computer to the DME series unit via the USB or Ethernet connection. DME series settings, configuration, and parameter data is sent via USB or Ethernet to the connected DME series unit. After the data is transmitted, you can disconnect the DME series unit from the computer and use it as an independent processor. You can also connect it to a computer and control it in realtime from DME Designer. If multiple DME series units are connected in the network, DME Designer enables you to build a configuration that includes those units. Please download the DME Designer application, driver, DME setup manual, and DME Designer owner's manual at the following URL: http://www.yamahaproaudio.com/ Refer to the “Connecting to a Computer” (page 18) for more information on connecting a computer to the DME Satellite. For details on how to install DME Designer and the drivers that are required for connection, refer to the “DME Setup Manual”. Refer to the DME Designer Owner’s Manual for setup and operation instructions. Introduction to the DME Satellite About DME Designer DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 13 Foreword Controls and Connectors Front Panel Introduction to the DME Satellite 2 DME8i-ES 1 Controls and Connectors Connecting to a Computer Audio I/O Connection Connecting to an External Device Other Functions 1 8 9 7 8 9 7 8 9 6 3 45 2 7 6 DME4io-ES 1 1 [USB] Connector Use this connector to connect the DME Satellite to the computer’s USB port. If you plan to use a USB connection, you must first install the USB-MIDI Driver on your computer. Refer to the “DME Setup Manual” (PDF file) for installation instructions. Be sure to follow the procedure below when you make a USB connection with a computer. Otherwise, the computer and/ or DME Satellite may freeze, resulting in damages or loss of data. If the computer or DME Satellite freezes, turn the power to the DME Satellite off and then on, then restart the computer. 3 45 CAUTION • Before you connect the DME Satellite to the computer via USB, cancel the computer’s energy saving mode (such as Suspend, Sleep, or Stand-by mode). • Before turning on the power to the DME Satellite, first connect its [USB] connector to the computer’s USB port. • Before turning the power to the unit on or off, and before connecting or disconnecting the USB cable, take the following actions: - Quit all open applications. - Make sure that the DME Satellite is NOT transferring any data. • Be sure to wait six seconds or more between turning the power to the unit on and then off (or off and then on), or between connecting and disconnecting (or vice versa) the USB cable. 2 [NETWORK] Indicator Lights orange while data communication is occurring via the [USB] or [NETWORK] connector. References 14 3 45 2 DME8o-ES 6 3 [MASTER] Indicator Lights green when the device is operating as the group master. The indicator is turned off if the device is operating as a slave. You can assign the group master in DME Designer. DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual Foreword Controls and Connectors 6 [PEAK] Indicators Light red when the signal level at the corresponding built-in analog audio inputs or outputs ([INPUT] or [OUTPUT] connectors) reaches or exceeds -3 dBFS. They also indicate an error number or status. 7 [SIGNAL] Indicators Light green when the signal level at the corresponding builtin analog audio inputs or outputs ([INPUT] or [OUTPUT] connectors) reaches or exceeds -40 dBFS. They also indicate the status, for example, of the initialization process. Lights consecutively in the clockwise direction This indicates that data is being written into internal memory, and part of the data may be damaged if you turn off the power at this time. Data writing will occur during the following operations. • While shifting to on-line operation • While storing or recalling or deleting scene memory • While saving changes to the Utility settings • While using the DME File Storage function to transmit/ receive or delete files • While updating the firmware, or while reverting to the previous firmware following a failed update Introduction to the DME Satellite Controls and Connectors Do not turn off the power while the front panel [SIGNAL] indicators are lighting consecutively in the clockwise direction. Connecting to a Computer 5 [TX/RX] Indicator These indicate the communication status of the signals from the EtherSound connector to the network. The transmission status is shown by the [TX] indicator, and the reception status by the [RX] indicator. The indicator will blink when signals are being sent correctly. The indicator will be dark if no cable is connected to the EtherSound connector, or if communication is not occurring successfully. INPUT: Indicates the communication status of the EtherSound [IN] connector. OUTPUT: Indicates the communication status of the EtherSound [OUT] connector. Caution when turning the power off Audio I/O Connection 4 [ERROR] Indicator Lights when an error occurs. The [PEAK] indicators reflect the type of error. The [ERROR] indicator flashes when the battery charge is getting low. NOT E Connecting to an External Device Remove the transparent protective film that was applied to the indicator panel prior to shipment from the factory. 8 [POWER] Indicator This will light when you turn the power on. • If “Last Mem. Resume” is set to ON, the unit will back up data to the internal memory periodically. In this case, do not turn off the power to the unit within five (5) seconds after you operate any parameters. References CAUTION Other Functions 9 [POWER] Switch Turns main power to the device on and off. The DME Satellite will start up with the same scene settings that were active when it shut down. You can use the “Last Mem. Resume” setting in DME Designer to set up the DME Satellite so that at startup it will recall the scene selected before you turned off the power to the device. DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 15 Foreword Controls and Connectors Rear Panel Introduction to the DME Satellite DME8i-ES 1 2 Controls and Connectors DME8o-ES Connecting to a Computer Audio I/O Connection 2 5 6 1 4 5 6 7 3 1 9 8 4 5 6 3 Connecting to an External Device 1 [AC IN] Connector Connect to the AC mains using the supplied AC power cord. First connect the power cord to the DME Satellite, then insert the power cord plug into an AC outlet. CAUTION 7 3 2 DME4io-ES 4 Even when the power switch is turned off, electricity is still flowing to the product all the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. Other Functions 2 Ground Screw The supplied AC power cable is a 3-wire type, so if the AC outlet used is properly earthed the DME Satellite will be earthed as well. Hum and interference may by further reduced in some cases by also connecting the earth screw to an earth point. References 3 Cooling vent The DME Satellite contains a cooling fan. The cooling air is exhausted here, so please be careful not to block this vent. 16 DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual ) 7 9 8 ) NOTE Use a STP (Shielded Twisted Pair) cable for this connection to prevent electromagnetic interference. 5 Dip Switch This 6-bit dip switch enables you to select the [REMOTE] connector function or initialize the DME Satellite, depending on its setting at the startup of the device. To switch between RS-232C and RS-422 for the [REMOTE] connector function, turn off the power to the device, set the dip switch as shown below, then turn on the power to the device again. See page 31 for the DME Satellite initialization procedure. RS-232C RS-422 RS-232C RS-232C RS-422 RS-422 If you do not plan to initialize the DME Satellite, CAUTION 4 [NETWORK] Connector This is a 100Base-TX/10Base-T Ethernet connector for connection to a computer or to another DME series unit in the network. See “Ethernet Connection ([NETWORK] Connector)” on page 20 for connection details. 8 set all dip switch bits (excluding one bit for the RS-422 setting) in the upper position. Foreword Controls and Connectors NOT E • The communication status of the EtherSound [IN]/[OUT] jacks is shown by the front panel [TX/RX] indicators. • Use a STP (Shielded Twisted Pair) cable to prevent electromagnetic interference. Fan kit DME Satellite 8 [GPI] Connector This Euroblock connector provides access to the unit’s GPI (General Purpose Interface) interface for transfer of control signals to and from external equipment. It features 8-port input and 4-port output. The +V terminals have an output voltage of 5 volts. The IN terminal detects voltage changes from 0V to 5V. The OUT terminals output either signal “L” or “H” at a TTL level. (See page 30.) DME Satellite Introduction to the DME Satellite Controls and Connectors If several DME Satellite units (or a DME Satellite unit together with other devices) are installed in a poorly-ventilated rack, the heat generated by each unit may raise the temperature inside the rack, preventing the DME Satellite from performing as designed. When mounting DME Satellite units in a rack, please leave one rack space vacant for every two units. You can attach a ventilation panel to this space or leave it open to prevent excessive heat build-up. If the temperature inside the rack is expected to rise above 40 degrees Celsius or 104 degrees Fahrenheit (or if the ambient temperature outside the rack is expected to rise above 30 degrees Celsius or 86 Fahrenheit), install a fan kit in the top row of the rack. The fan must provide airflow of 1.6m3/min or more and static pressure of 5mmH2O or more. Connecting to a Computer 7 EtherSound [IN]/[OUT] Connectors These connectors input and output audio signals and control signals between devices. Use an Ethernet cable (CAT5e or higher category) to daisy-chain multiple DME Satellite units. For more about EtherSound connections, refer to pages 24 and 28. Precautions for Using a Rack-mounted DME Satellite Ventilation panel DME Satellite DME Satellite Connecting to an External Device 9 [INPUT] Connectors These Euroblock connectors receive 8-channel analog audio signals on the DME8i-ES. These Euroblock connectors receive 4-channel analog audio signals on the DME4io-ES. Audio I/O Connection 6 [REMOTE] Connector This 9-pin D-SUB connector allows connection to a Yamaha AD824 or AD8HR remote head amplifier or an RS-232C/ RS-422 compatible controller such as those from AMX or Crestron. You can also connect a Yamaha PM5D or DM2000 and control the internal head amps of the DME8i-ES/ DME4io-ES. See “Remote Connection ([REMOTE] Connector)” on page 26 for connection details. NOT E Other Functions • The PAD will be internally switched on or off when the gain of the DME8i-ES/DME4io-ES internal head amp is adjusted between –6 dB and –5 dB. Keep in mind that noise may be generated if there is a difference between the Hot and Cold output impedance of the external device connected to the INPUT connector when using phantom power. References ) [OUTPUT] Connectors These Euroblock connectors output 8-channel analog audio signals on the DME8o-ES. These Euroblock connectors output 4-channel analog audio signals on the DME4io-ES. DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 17 Foreword Connecting to a Computer USB Connection Introduction to the DME Satellite To connect multiple DME Satellite units to a network, you must assign appropriate IP addresses and make other network settings on all units. To achieve this, you need to connect the [USB] connector of one of the DME Satellite units to the USB port of the computer using USB cables, install USB-MIDI Driver and DME Designer on the computer, then assign the IP addresses to the DME Satellite units from DME Designer. N OT E Controls and Connectors • Refer to the “DME Setup Manual” (PDF file) for details on installing USB-MIDI Driver and DME Designer. • Make sure that the USB-MIDI Driver’s THRU setting is “OFF.” • Refer to “Network Settings” on page 19 for more information on assigning IP addresses from DME Designer. Connecting to a Computer USB connections can be used in the following three ways: (1) Set up the network (e.g., assign a unique IP address to each DME Satellite) from DME Designer. (2) Control the DME Satellite from DME Designer. (3) Connect to any individual DME Satellite and control that DME Satellite unit by transmitting MIDI commands from a MIDI sequencer or similar software. N OT E • The computer on which DME Designer is running can be connected to either the group master or a slave DME series unit. In this case, set the DME Satellite as the group master. • The correspondence between the MIDI commands to be received/transmitted and the scene parameters can be set up using DME Designer. • The USB port being used by DME Designer is not available for use by a MIDI sequencer or other application. Audio I/O Connection USB Cable Device Group DME Satellite Connecting to an External Device Ethernet Cable Computer (Running DME Designer.) Switching Hub Other Functions Ethernet Straight Cable Ethernet Cable DME64N/24N DME Satellite SCENE HOME UTILITY LEVEL MUTE CANCEL ENTER USB Cable References 18 DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual Computer (Running MIDI Sequencer or similar application.) Foreword Connecting to a Computer Network Settings Setting the IP address Host Address • Subnet mask is fixed at 255.255.255.0. • The network address of Gateway is the same as that of IP address. The host address of Gateway is automatically set to 254. • Assign each of DME series units a unique IP address so that there are no duplicates. Assigning duplicate IP addresses may cause serious network problems. • You cannot make any network settings while using the DME Designer application on-line. To make network settings, first set DME Designer off-line. Refer to the DME Designer Owner’s Manual for details. Master and slave setting Each device group must have one master. All other devices in the group are assigned as slave. The fourth octet of a slave DME Satellite’s master ID must be the same value as the fourth octet of the group master DME Satellite’s IP address. Audio I/O Connection NO T E Connecting to an External Device Each group of digits between periods in an IP address is called an “octet.” These groups of digits are called “1st octet,” “2nd octet,” etc., starting from the left-most digit group. You cannot specify 0, 127, or 223 through 255 for the 1st octet of the network address. You can specify the following range of values for the 4th octet. Master : 2-253 Slave : 3-253 Connecting to a Computer Controls and Connectors Network Address Introduction to the DME Satellite Use DME Designer to specify the IP address, master/slave, and master ID settings as follows. References When using a DME Satellite together with the DME64N/24N, you must assign the DME Satellite (including the DME8i-C/ DME8o-C/DME4io-C) as the master. If you assign the DM64N/24N as the device group master, you will be unable to synchronize using DME Designer. Other Functions NO T E DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 19 Foreword Connecting to a Computer Ethernet Connection ([NETWORK] Connector) To control the DME Satellite from the computer via Ethernet, use an Ethernet cable to connect the [NETWORK] connector on the rear panel of the DME Satellite to the computer, then install DME-N Network Driver. Introduction to the DME Satellite N OT E • Refer to the “DME Setup Manual” (PDF file) for details on installing DME-N Network Driver. • Appropriate IP addresses must first be assigned to all devices connected to an Ethernet network. Connect your computer to one of the DME Satellite units via USB, then assign the IP addresses from DME Designer (page 18). Two DME Satellite units directly connected via Ethernet Controls and Connectors DME Satellite Ethernet Cable Connecting to a Computer DME Satellite USB Cable Audio I/O Connection You can connect devices in the same device group directly to each other using Ethernet cables, without connecting them to a switching hub. If they are DME Satellite units, you can use either crossover cables or straight cables. In this case, from DME Designer set Link Mode on both units to the same setting. Devices in different subnet (different network address) groups can be connected via a router or layer-3 compliant switching hub. HINT Connecting to an External Device Since the DME Satellite supports Auto MDI/MDI-X, it will automatically detect whether the connected cable is of the straight type or crossover type, and will configure itself to create the optimal connection. Therefore, you can use either a straight or crossover cable. Other Functions References 20 DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual Foreword Connecting to a Computer Control from a computer in the same subnet group Device Group Introduction to the DME Satellite Group Master DME Satellite (IP address: 192.168.0.7) Ethernet Cable Ethernet Straight Cable SCENE HOME UTILITY LEVEL MUTE Computer (IP address: 192.168.0.100) CANCEL ENTER DME64N/24N (IP address: 192.168.0.250) (Master ID: 7) NO T E References Other Functions Connecting to an External Device • The IP addresses in the diagram are examples. • Use a switching hub that is compatible with 100Base-TX/10Base-T network speeds. The maximum length of a cable between a switching hub and the DME Satellite is 100 meters. Due to the quality of cables and switching hub performance, however, proper operation at the maximum length cannot be guaranteed in some cases. Use a STP (Shielded Twisted Pair) cable to prevent electromagnetic interference. • If you are using multiple DME series units, set Link Mode on each unit to the same setting. Yamaha recommends that you select 100Base-TX for the Link Mode setting. • You can also connect a supported controller such as the AMX or Crestron, and control the DME Satellite remotely. For details, refer to “Connecting to an External Device” on page 26. Connecting to a Computer DME Satellite (IP address: 192.168.0.3) (Master ID: 7) Ethernet Straight Cable Audio I/O Connection Ethernet Cable Controls and Connectors Switching Hub DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 21 Foreword Connecting to a Computer Control from a computer with a different subnet Device Group Introduction to the DME Satellite Group Master DME Satellite (IP address: 192.168.0.5) Ethernet Cable Switching Hub Controls and Connectors Ethernet Straight Cable Ethernet Cable Connecting to a Computer SCENE HOME UTILITY Router or Layer-3 Compliant Switching Hub Ethernet Straight Cable Computer Ethernet Straight Cable DME Satellite (IP address: 192.168.0.3) (Master ID: 5) LEVEL MUTE CANCEL ENTER DME64N/24N (IP address: 192.168.0.12) (Master ID: 5) Audio I/O Connection Connecting to an External Device Other Functions References 22 Port settings • Destination network address: 192.168.0.0 • Subnet mask: 255.255.255.0 • Gateway: 192.168.0.254 DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual Foreword Connecting to a Computer Connecting multiple device groups Device Group 1 Device Group 2 Group Master DME Satellite (IP address: 192.168.0.2) Ethernet Cable DME Satellite (IP address: 192.168.0.3) Ethernet Cable Ethernet Straight Cable Ethernet Straight Cable Ethernet Straight Cable Ethernet Cable LEVEL MUTE CANCEL ENTER SCENE DME64N/24N (IP address: 192.168.0.100) (Master ID: 2) DME Satellite (IP address: 192.168.0.40) (Master ID: 2) Ethernet Cable HOME UTILITY LEVEL MUTE CANCEL ENTER DME64N/24N (IP address: 192.168.0.200) (Master ID: 3) Audio I/O Connection DME Satellite (IP address: 192.168.0.10) (Master ID: 3) Computer (IP address: 192.168.0.1) Connecting to an External Device UTILITY Other Functions HOME References SCENE Controls and Connectors Switching Hub Connecting to a Computer Switching Hub Introduction to the DME Satellite Group Master DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 23 Foreword Audio I/O Connection Digital Audio Connection (EtherSound Connectors) Introduction to the DME Satellite You can use the DME Satellite’s EtherSound connector to input and output digital audio signals, control signals, and word clock signals. When connecting DME Satellites, make daisy-chain connections between the EtherSound [OUT] connector → [IN] connector, and the [OUT] connector → [IN] connector. Audio signals and word clock signals can also be input and output between EtherSound compatible devices and devices such as mixers in which the MY16-ES64 card has been installed. Input and output of audio signals and word clock signals can be specified using the “AVS-ESMonitor” application software made by AuviTran SARL. For details on interface cards and application software, refer to the appropriate Owner’s Manual. Controls and Connectors About AVS-ESMonitor AVS-ESMonitor is application software made by the AuviTran SARL for the purpose of monitoring and controlling an EtherSound system. It allows you to make various EtherSound settings such as input/output routing. For details, refer to the following website. http://www.auvitran.com/view.php?products_AVS-ESMonitor.php Connecting to a Computer Example: Connection to EtherSound devices EtherSound [OUT] connector Ethernet Cable EtherSound [IN] connector EtherSound [OUT] connector Ethernet Cable EtherSound [IN] connector Audio I/O Connection MY16-ES64 DME Satellite DME Satellite SCENE HOME UTILITY LEVEL MUTE CANCEL ENTER DME64N/24N Connecting to an External Device N OT E • DME Satellites and the MY16-ES64 can transmit and receive control data such as for internal head amps via EtherSound. However in some cases, it may not be possible to transmit or receive control data depending on the device in which the MY card is installed. For details, refer to the operating manual of the device in which the card is installed. • For details on EtherSound specifications and the length of the cables that can be used, refer to the following website. http://www.ethersound.com/ Other Functions References 24 DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual Foreword Audio I/O Connection Euroblock plug connection Please be sure to use the supplied Euroblock plugs. If you lose them, contact your nearest Yamaha dealer. NO T E 3 mm Cable preparation • To prepare the cable for attachment to a Euroblock connector, strip the wire as shown in the illustration, and use stranded wire to make connections. With a Euroblock connection, the stranded wire may be prone to breakage because of metal fatigue due to the weight of the cable or due to vibration. When rack-mounting your equipment, use a lacing bar when possible to bundle and fasten the cables. If cables will be frequently connected and disconnected, as in the case of a portable installation, we recommend that you use ferrules with insulation sleeves. Use a ferrule whose conductor portion has an external diameter of 1.6 mm (1.3 mm for GPI) or less, and a length of approximately 7 mm (5 mm for GPI) (such as the AI0,5-6WH made by the Phoenix Contact corporation). approx.7 mm (5 mm for GPI) approx.7 mm (5 mm for GPI) 1.6 mm (1.3 mm for GPI) or less If you use stranded wire, do not tin (plate with solder) the exposed end. Connecting to a Computer • Audio I/O Connection Use a slotted screwdriver with a blade width of about 3 millimeters to secure the cables to the (3P) Euroblock plug. Use a slotted screwdriver with a blade width of about 2 millimeters to secure the cables to the (16P) Euroblock plug to connect to the [GPI] connector. Controls and Connectors The DME Satellite can directly input and output audio signals via the [INPUT] and [OUTPUT] connectors. Wire the supplied Euroblock plugs (3P) as shown below. You can use DME Designer to set the head amplifier gain and turn the phantom power on and off for each [INPUT] connector. Introduction to the DME Satellite Analog Audio Connection ([INPUT] & [OUTPUT] Connectors) Loosen Slotted Screwdriver Terminal Screw Euroblock Plug 2. Insert cables. 3. Securely tighten terminal screws. References Pull the cables (not too strongly) to confirm that they are securely connected. Other Functions 1. Loosen terminal screws. Connecting to an External Device CAUTION 4. Insert the Euroblock plug into the Euroblock connector on the rear panel. DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 25 Foreword Connecting to an External Device Remote Connection ([REMOTE] Connector) Introduction to the DME Satellite The [REMOTE] connector of the DME Satellite can be connected to remotely-controllable Yamaha AD8HR or AD824 head amplifiers (pre-amps), digital mixers, or RS-232C compatible controllers (such as those from AMX or Crestron). The [REMOTE] connector also transmits and receives MIDI messages. Controlling external head amplifiers from the DME Satellite Controls and Connectors You can remotely control the AD8HR or AD824 head amplifier settings from DME Designer. Up to eight AD8HR/AD824 head amplifiers can be connected. Be sure to set the dip switch on the rear panel of the DME Satellite to “RS-422” (page 16) when connecting to AD8HR or AD824 remote head amplifiers. Do not change the dip switch setting to any position other than to “RS-422” while the devices are connected to prevent possible damage to the device(s). When connecting to a combination of AD8HR and AD824 head amplifiers, be sure to place the AD8HR units closest to the DME Satellite in the chain, otherwise the AD8HR or AD824 unit(s) may not be properly recognized by the DME Satellite. Connecting to a Computer D-SUB 9-pin Cable (Interlink Crossover) Set to RS-422 REMOTE DME Satellite HA REMOTE 1 Audio I/O Connection AD8HR COM PC/RS-422 Connecting to an External Device AD824 HA REMOTE 1 HA REMOTE 2 AD8HR COM RS-422 COM PC/RS-422 AD824 COM RS-422 COM PC/RS-422 AD824 N OT E Only control signals are transmitted and received via the REMOTE connection. Audio connections must be made separately. Other Functions References 26 HA REMOTE 2 DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual Foreword Connecting to an External Device The internal head amp settings of a DME8i-ES or DME4io-ES can be remotely controlled from a digital mixer such as the Yamaha PM5D or DM2000. Connect the digital mixer to the DME series’ [REMOTE] connector, and use an Ethernet cable to make connections between the [NETWORK] connectors of the DME series. From the digital mixer, DME series units can be controlled as an AD8HR. The gain and the phantom power (+48V) can be controlled. Introduction to the DME Satellite Controlling a DME Satellite’s internal head amps from a digital mixer Ethernet Cable DME Satellite DME Satellite NO T E • Only one mixer can be connected within each device group. • The digital mixer can be connected to any DME series unit, whether it is the group master or a slave unit. • The ID number of the DME series unit being remotely controlled is specified from DME Designer. For details on making this setting, refer to the “DME Designer Owner’s Manual.” • If the connection between DME series units is broken, it will no longer be possible to communicate with DME units of an ID number that follows the disconnected DME. • The variable range of GAIN differs between the AD8HR and the DME Satellite. You cannot use the mixer to specify a value that exceeds the variable range of the DME Satellite. Controlling the DME Satellite from an external device You can remotely control the DME Satellite from a connected RS-232C or RS-422 compatible controller, such as those from AMX or Crestron. Be sure to set the dip switch on the rear panel of the DME Satellite correctly (page 16) in accordance with a connected RS-232C or RS-422 compatible remote controller. Do not change the dip switch setting to any other position while the devices are connected to prevent possible damage to the device(s). NO T E • The port used for remote control is specified from DME Designer. For details on making this setting, refer to the “DME Designer Owner’s Manual.” • Refer to “DME Remote Control Protocol Specifications” on the Yamaha web site for more information on communication protocols used to control the DME Satellite from an external device (such as those from AMX or Crestron). http://www.yamahaproaudio.com/ DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual Connecting to a Computer DME Satellite Audio I/O Connection Digital Mixer Switching Hub Connecting to an External Device DME Satellite Other Functions REMOTE References REMOTE Controls and Connectors D-SUB 9-pin Cable 27 Foreword Connecting to an External Device EtherSound Connection (EtherSound Connectors) You can use the EtherSound connector to control the DME Satellite’s internal head amp or other functionality. Introduction to the DME Satellite Controlling DME Satellite’s internal head amps from a digital mixer Controls and Connectors The internal head amp settings of a DME8i-ES or DME4io-ES can be remotely controlled from a digital mixer such as the Yamaha PM5D or DM2000. Connect the digital mixer using a D-sub 9-pin cable to the MY16-ES64 card, and use EtherSound to make connections between the MY16-ES64 card and DME series. Use an Ethernet cable connected to the [NETWORK] connectors to make connections between DME series units. The gain and the phantom power (+48V) can be controlled from the digital mixer. EtherSound Ethernet Hub Ethernet Switching Hub Connecting to a Computer DME8i-ES EtherSound D-Sub 9-pin DME8i-ES Audio I/O Connection MY16-ES64 Connecting to an External Device Other Functions MY16-EX DME4io-ES Digital Mixer Switching Hub DME4io-ES N OT E • Only one mixer can be connected within each device group. • The digital mixer can be connected to any DME series unit, whether it is the group master or a slave unit. • Control signal settings are made using AuviTran’s “AVS-ESMonitor” application software. Refer to the DME Designer manual for details. • The ID number of the DME series unit being remotely controlled is specified from DME Designer. For details on making this setting, refer to the “DME Designer Owner’s Manual.” • If the connection between DME series units is broken, it will no longer be possible to communicate with DME units of an ID number that follows the disconnected DME. • For details on controlling the head amps from a digital mixer not equipped with a [REMOTE] connector, refer to the mixer’s owner’s manuals. References 28 Ethernet Cable DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual Foreword Connecting to an External Device Network Connection ([NETWORK] Connectors) NO T E References Other Functions Connecting to an External Device Audio I/O Connection Connecting to a Computer Controls and Connectors • The port used for remote control is specified from DME Designer. For details on making this setting, refer to the “DME Designer Owner’s Manual.” • Refer to “DME Remote Control Protocol Specifications” on the Yamaha web site for more information on communication protocols used to control the DME Satellite from an external device (such as those from AMX or Crestron). http://www.yamahaproaudio.com/ Introduction to the DME Satellite You can connect a controller such as the AMX or Crestron to DME Satellites via Ethernet, and remotely control multiple DME Satellite units. DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 29 Foreword Connecting to an External Device GPI Connection ([GPI] Connector) Introduction to the DME Satellite A GPI (General Purpose Interface) device (GPI controller, etc.) can be connected to the rear panel [GPI] connectors to enable the transfer of a variety of control signals. Optional CP4SW, CP4SF, and CP1SF Control Panels can be also connected via GPI. The DME Satellite features 8-port GPI input and 4-port GPI output. The +V terminals have an output voltage of 5 volts. The IN terminal detects voltage changes from 0V to 5V. The OUT terminals output either signal “L” or “H” at a TTL level. The parameters for each GPI input and output are assigned via the DME Designer application. Euroblock connectors are used for all GPI input and output connections. Euroblock connection methods are described in “Euroblock plug connection” on page 25 in this manual. Controls and Connectors N OT E • For more information on the CP4SW, CP4SF, and CP1SF Control Panels, refer to the CP4SW/CP4SF/ CP1SF Owner’s Manual. • You can use DME Designer to set up the system so that scene recall operations and User Defined parameter control can be carried out from connected GPI control devices. Refer to the DME Designer Owner’s Manual for details. Connecting to a Computer Example: Controlling the DME Satellite from a switch box Example: Controlling the DME Satellite via a 10k ohm linear taper potentiometer. GPI Connection IN Example: Lighting LED indicators on the external devices from the DME Satellite GPI Connection IN +V +V GPI Connection OUT GND Audio I/O Connection Max. 16mA Continuous Variable Volume CAUTION Connecting to an External Device Other Functions DME Satellite [GPI] Connector DME Satellite [GPI] Connector Euroblock Plug Euroblock Plug Remote Switch Box Remote Fader Box 4 3 2 1 Switches References 30 GND Make sure that the current between the OUT and GND [GPI] connectors is less than 16mA. DME Satellite [GPI] Connector Euroblock Plug Remote LED Box 4 3 2 1 10k ohm Linear Taper Potentiometer N OT E You can use DME Designer to adjust the input calibration parameters for the [GPI] connector. DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 4 3 2 1 LEDs and Resistors Foreword Other Functions Initialize DME: All scenes, preset parameter settings and WAVE files except components and files saved via the File Storage function will be deleted. The Utility settings will be set to default values. Delete All Data: All stored component, scene, preset parameter settings, WAVE files, and files saved via the File Storage function will be deleted. The Utility settings will be set to default. Use this initialization type if the internal data is damaged or corrupted. After initialization, transfer necessary components from DME Designer. Controls and Connectors You can initialize the DME Satellite internal memory. Select one of the following initialization types: Introduction to the DME Satellite Initializing the DME Satellite 1. While the DME Satellite is turned off, set the dip switch on the rear panel to the following Connecting to a Computer position, then turn on the power to the unit. RS-232C Initialize DME: RS-422 RS-232C Delete All Data: Four [PEAK] indicators on the upper row on the front panel light up during the initialization process. Four [SIGNAL] indicators on the lower row of the front panel flash when the initialization process is complete. Four [PEAK] indicators on the lower row of the front panel flash if the initialization process fails. Do NOT turn off the power to the DME Satellite during the initialization process to prevent possible damage to the device. 2. When initialization is complete, reset the dip switch to its previous position (page 16), then turn off and on the power to the unit. Be sure to reset the dip switch to the previous position to prevent possible damage to the device. References Other Functions CAUTION Connecting to an External Device CAUTION Audio I/O Connection RS-422 DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 31 Foreword References Options Introduction to the DME Satellite The ICP1, CP4SW, CP1SF, and CP4SF controllers are available as options for remote external control of the DME series. The ICP1 connects via Ethernet, while the CP4SW, CP1SF, and CP4SF connect via the GPI interface. For more information on installing your Control Panel and connecting it to a DME series unit, refer to the owner’s manual that came with the Control Panel. For more information on settings, refer to the DME Designer Owner’s Manual. ICP1 Controls and Connectors This controller connects to a DME series unit via Ethernet. Like the DME series units, a unique IP address must be assigned to each controller unit. Data is transmitted and received via Ethernet cables. You can assign and control any function of all DME series units in the same device group via the controller. Up to four parameter sets can be assigned to six function keys (F1 – F6) located above and under the LCD. You can control up to 24 parameters by selecting a display page using the [HOME] key. Connecting to a Computer Audio I/O Connection Connecting to an External Device CP4SW, CP4SF, and CP1SF These controllers connect to DME series units via the [GPI] connectors. These controllers control only the DME series units to which they are directly connected. The controller switches enable you to turn the parameter settings On and Off. The switch LEDs enable you to check the parameter status. The faders enable you to control the parameter values. Other Functions References 32 CONTROL PANEL CP4SW DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 10 10 10 10 10 0 0 0 0 0 CONTROL PANEL CONTROL PANEL CP4SF CP1SF Foreword References No audio input is present. • • • • Connect the cable properly. Check to see if signals are being received from an external device. Did you use AVS-ESMonitor to make EtherSound settings such as routing? Set the gain of the internal head amplifier or external head amplifier to an appropriate level. No audio is output. • • • • • • Connect the cable properly. Did you use AVS-ESMonitor to make EtherSound settings such as routing? Make sure that the output level set in DME Designer is not too low. Make sure that the Mute setting in DME Designer is set to Off. You may have designed a scene in DME Designer that mutes audio output. You may have tried to use a configuration at 96 kHz that does not support 96 kHz. The selected scene changes unexpectedly. • Use DME Designer to check the MIDI Program Change assignments. • Use DME Designer to check the GPI input assignments. MIDI messages cannot be transmitted or received. • Make sure that the power to the MIDI device is turned on. • Set the MIDI port properly. • Set the receive and transmit channels properly. Scenes cannot be recalled via MIDI Program Change messages. • Use DME Designer to change the setting so that the required MIDI Program Change messages will be received properly. • Make the appropriate Program Change Table settings via DME Designer. Parameters cannot be controlled via MIDI Control Change messages. • Use DME Designer to set the parameters correctly to allow Control Change message reception. • Make the appropriate MIDI Control Change Table settings via DME Designer. Parameters cannot be edited via MIDI Parameter Change messages. • Use DME Designer to set the parameters correctly to allow Parameter Change message reception. • Make the appropriate MIDI Parameter Change Table settings via DME Designer. Component References Other Functions Refer to the DME Designer Owner’s Manual for more information on each component. Controls and Connectors • Connect the cable properly (page 18, 20). • Make sure that USB-MIDI Driver has been installed correctly. • If the [NETWORK] connector is being used for connection, make sure that you have set the DME-N Network Driver correctly. • The DME Designer version should be 3.0 or later. • Make the Port setting. Connecting to a Computer No communication between the DME Satellite and the DME Designer application software. Audio I/O Connection • Connect the power cord properly (page 7). • Make sure that the [POWER] switch is turned ON (page 15). • If the device still does not turn on, contact a Yamaha dealer. Connecting to an External Device The device does not turn on, or the panel LEDs do not light up. Introduction to the DME Satellite Troubleshooting DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 33 Foreword References MIDI Data Format MIDI Tx CH: MIDI Tx Channel (1-16) Introduction to the DME Satellite 1. MIDI functions on the DME8i-ES, DME8o-ES, and DME4io-ES Controls and Connectors 1.1 Scene Change Scene recall occurs according to the “MIDI Program Change Table” assignments when appropriate MIDI Bank Select MSB/LSB and Program Change messages are received by the DME8i-ES/ DME8o-ES/DME4io-ES. When a scene recall operation is carried out via DME Designer, corresponding MIDI Bank Select MSB/LSB and Program Change messages are also transmitted by the DME8i-ES/DME8o-ES/ DME4io-ES as specified by the “MIDI Program Change Table” assignments. Transmission does not occur while configurations are being switched. 1.2 Parameter Control Connecting to a Computer Audio I/O Connection MIDI Control Change and Parameter Change messages transmitted to the DME8i-ES/DME8o-ES/DME4io-ES can be used to control parameters according to the “MIDI Control Change Table” and “MIDI Parameter Change Table” assignments. When a parameter is edited via DME Designer, corresponding MIDI Control Change and Parameter Change messages are also transmitted by the DME8i-ES/DME8o-ES/ DME4io-ES as specified by the “MIDI Control Change Table” and “MIDI Parameter Change Table” assignments. “MIDI Program Change Table,” “MIDI Control Change Table,” and “MIDI Parameter Change Table” assignments can be made via DME Designer. Refer to the DME Designer Owner’s Manual for details. Connecting to an External Device 2. MIDI Data Flow MIDI IN MIDI Rx CH SW1 Bank Select MSB/LSB Program Change (Scene Recall) SW2 Control Change (Parameter Edit) SW3 Parameter Change (Parameter Edit) Other Functions SW4 Control Change (Echo Back) SW5 Parameter Change (Echo Back) SW6 Control Change SW7 MIDI Tx CH MIDI OUT SW8 Parameter Change SW9 References 34 Specifies basic MIDI operation. Use DME Designer to make the setting. 3.1 Host Select Selects the input/output ports to be used for MIDI communication. 3.2 MIDI Tx Channel Specifies the MIDI transmit channel (1 ~ 16). 3.3 MIDI Rx Channel Specifies the MIDI receive channel (1 ~ 16). 3.4 MIDI Tx Switch Program Change Tx Switch: turns Bank Select MSB, LSB, and Program Change transmission on or off. Control Change Tx Switch: turns Control Change transmission on or off. Parameter Change Tx Switch: turns Parameter Change transmission on or off. 3.5 MIDI Rx Switch Program Change Rx Switch: turns Bank Select MSB, LSB, and Program Change reception on or off. Control Change Rx Switch: turns Control Change reception on or off. Parameter Change Rx Switch: turns Parameter Change reception on or off. 3.6 MIDI Omni Switch Program Change Omni Switch: turns the Bank Select MSB, LSB, and Program Change omni mode on or off. Control Change Omni Switch: turns the Control Change omni mode on or off. 3.7 MIDI Echo Back Switch Program Change Echo Back Switch: turns Bank Select MSB, LSB, and Program Change echo back on or off. Control Change Echo Back Switch: turns Control Change echo back on or off. Parameter Change Echo Back Switch: turns Parameter Change echo back on or off. Bank Select MSB/LSB Program Change (Echo Back) Bank Select MSB/LSB Program Change 3. MIDI Setup MIDI THRU SW1: Program Change Rx Switch [On/Off] SW2: Control Change Rx Switch [On/Off] SW3: Parameter Change Rx Switch [On/Off] SW4: Program Change Echo Back Switch [On/Off] SW5: Control Change Echo Back Switch [On/Off] SW6: Parameter Change Echo Back Switch [On/Off] SW7: Program Change Tx Switch [On/Off] SW8: Control Change Tx Switch [On/Off] SW9: Parameter Change MIDI Rx CH: MIDI Rx Channel (1-16) DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual Foreword References Number Format Notation Numbers ending with “h” are in hexadecimal format, while numbers ending with “b” are binary format. Characters “A” through “F” in hexadecimal numbers represent decimal values 10 through 15. Other lower-case characters (usually “n” or “x”) can represent any number. Status Data Bnh (1101nnnnb) 00h (00000000b) Data nnh (0nnnnnnnb) Bank Select LSB Status Data MIDI Format Chart (Rx: receive, Tx: transmit} nnh (0nnnnnnnb) Control Change Control Change No. 32 (Bank Select LSB) Control Value (Bank Select LSB No.) System Real-time Message System Exclusive Message Editing the parameters Program Change (Cnn) Rx/Tx Scene Recall 4.2 Active Sensing (FEh) TIMING CLOCK (F8h) Rx MIDI Clock Receive ACTIVE SENSING (FEh) Rx MIDI Cable Check Receive MIDI communication will be initialized if no data is received within 300 ms after reception (Running Status, etc., will be cleared). Rx/Tx Editing the parameters Parameter Change Status Data Cnh (1100nnnnb) nnh (0nnnnnnnb) Program Change Program Change No. (0-127) Active Sensing Status FEh (11111110b) Active Sensing 4.3 Control Change (Bnh) Receive When the “Program Change Rx Switch” is on, Program Change messages are received on the MIDI channel specified by the “MIDI Rx Channel” parameter. If the “Program Change Omni Switch” is also on, however, Program Change messages will be received on all MIDI channels regardless of the “MIDI Rx Channel” setting. When a Program Change message is received, the scene assigned to the received program number in the “MIDI Program Change Table” is recalled. The effective Bank Select, Program Change range is as follows: Bank Select MSB: 0 Bank Select LSB: 0-7 Program Change No.: 0-127 Transmit When the “Program Change Tx Switch” is on and a scene is switched from DME Designer, the corresponding Program Change number will be transmitted as specified by the “MIDI Program Change Table” and “MIDI Tx Channel” settings. If multiple Program Change numbers are assigned to a single scene, the Bank Select MSB/LSB and Program Change number corresponding to the lowest number will be transmitted. Receive When the “Control Change Rx Switch” is on, Control Change messages are received on the MIDI channel specified by the “MIDI Rx Channel” parameter. If the “Control Change Omni Switch” is also on, however, Control Change messages will be received on all MIDI channels regardless of the “MIDI Rx Channel” setting. Control Change parameter resolution is 128 regardless of the effective range of the parameter. For finer settings use Parameter Change. Transmit When the “Control Change Tx Switch” is on and a parameter is edited via DME Designer, appropriate Control Change data will be transmitted as specified by the “MIDI Control Change Table” and “MIDI Tx Channel” settings. Refer to “Supplementary Information 1” for cases in which multiple messages are assigned to a single parameter. Status Data Bnh (1011nnnnb) cch (0cccccccb) vvh (0vvvvvvvb) Control Change Control Change No. (1-31,3395,102-119) Control Value (0-127) 4.4 Parameter Change (F0h - F7h) Receive When the “Parameter Change Rx Switch” is On, Parameter Change messages are received on the MIDI channel specified by the “Device ID (Rx Ch)” parameter. References 4.1 Program Change (Cnh) Connecting to a Computer Channel Message Rx/Tx Audio I/O Connection Program Change No. Control Change (Bnh) Controls and Connectors Function Connecting to an External Device Rx/Tx Bnh (1101nnnnb) 20h (00100000b) Other Functions Command Control Change Control Change No. 0 (Bank Select MSB) Control Value (Bank Select MSB No.) Introduction to the DME Satellite Bank Select MSB 4. MIDI Format DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 35 Foreword References Introduction to the DME Satellite Transmit When the “Parameter Change Tx Switch” is On and a parameter is edited via DME Designer, appropriate Parameter Change data will be transmitted as specified by the “MIDI Parameter Change Table” and “MIDI Tx Channel” settings. Refer to “Supplementary Information 1” for cases in which multiple messages are assigned to a single parameter. Refer to “Supplementary Information 2” for information on setting Parameter Data values. Controls and Connectors Connecting to a Computer Status ID No. F0h (11110000b) 43h (01000011b) DEVICE ID. GROUP ID. MODEL ID. Parameter Address 1xh 3Eh 10h aah (0001xxxxb) (00111110b) (00010000b) (0aaaaaaab) System Exclusive Message Manufacturer’s ID No.(YAMAHA) Rx/Tx Channel (0-15) Digital Mixer Device Code (DME) Parameter Address High aah Parameter ddh Data Value ddh ddh ddh ddh EOX F7h (0aaaaaaab) (0dddddddb) Parameter Address Low data 0 (0dddddddb) (0dddddddb) (0dddddddb) (0dddddddb) (11110111b) data 1 data 2 data 3 data 4 End of Exclusive Audio I/O Connection Supplementary Information 2 Setting the Parameter Change Message Parameter Data Values The Parameter change parameter values are expressed as 32-bit integers with or without parity. • A parity bit (positive:0, negative:1) is added above the most significant value bit (bit 31). • Fractional parameters will be converted according to the integer table. • For integers with parity, negative numbers are expressed as the 2’s complement. parity bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7 bit8 bit9 bit10 bit11 bit12 bit13 bit14 bit15 bit16 bit17 bit18 bit19 bit20 bit21 bit22 bit23 bit24 bit25 bit26 bit27 bit28 bit29 bit30 bit31 Connecting to an External Device 0 0 data 0 data 1 data 2 data 3 data 4 Example: • Decimal value 1000 → Hexadecimal value 3E8h Positive 0 0 0 0 0 3 E 8 Other Functions 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 1 0 0 0 data 0 = 00h data 1 = 00h data 2 = 00h data 3 = 07h data 4 = 68h • Decimal value 1000 → Hexadecimal value FFFFFC18h (2’s complement of 3E8h) Negative References 36 Supplementary Information 1 Messages Transmitted When Multiple Messages are Assigned to the Same Parameter The DME8i-ES/DME8o-ES/DME4io-ES MIDI transmit messages are specified via the “MIDI Control Change Table” and “MIDI Parameter Change Table.” (The “MIDI Control Change Table” and “MIDI Parameter Change Table” can be set up via DME Designer.) Multiple messages can be assigned to a single parameter, but the DME8i-ES/DME8o-ES/DME4io-ES will only transmit one of the assigned messages. The transmitted messages are as follows: • If a Control Change message and a Parameter Change message are assigned to the same parameter → the Control Change message will be transmitted. • If multiple Control Change numbers are assigned to the same parameter → the smallest Control Change number message will be transmitted. • If multiple Parameter Change numbers are assigned to the same parameter → the smallest Parameter Change number message will be transmitted. F F F F F C 1 8 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 1 1 0 0 0 data 0 = 1Fh data 1 = 7Fh DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual data 2 = 7Fh data 3 = 78h data 4 = 18h YAMAHA [Digital Mixing Engine Satellite] Model DME8i-ES, DME8o-ES, DME4io-ES MIDI Implementation Chart Recognized Basic Channel Default Changed 1 - 16 1 - 16 1 - 16 1 - 16 Mode Default Messages Altered ˛ ˛ ˛ ˛ ˛ ˛ ˛ ˛ ************** Velocity Note ON ˛ Note OFF ˛ ˛ ˛ After Touch Key's Ch's ˛ ˛ ˛ ˛ ˛ ˛ Pitch Bend 0,32 1-31,33-95,102-119 *1 *2 Ø Ø 0 - 127 *1 ************** Ø *3 Ø Ø Ø Memorized Controls and Connectors Note Number : True voice ************** Remarks Introduction to the DME Satellite Transmitted *1 *2 Connecting to a Computer Function... Date :14-FEB-2007 Version : 1.0 Foreword MIDI Implementation Chart Bank Select Assignable Audio I/O Connection Control Ø True # System Exclusive Common Ø : Song Pos. ˛ : Song Sel. ˛ : Tune ˛ ˛ ˛ ˛ ˛ : : : Mes- : sages: : ˛ ˛ ˛ ˛ ˛ ˛ ˛ ˛ ˛ ˛ Ø ˛ All Sound Off Reset All Cntrls Local ON/OFF All Notes OFF Active Sense Reset *1 *3 Assignable ˛ ˛ ˛ System : Clock Real Time : Commands Aux 0 - 127 0 - 127 Other Functions : References Prog Change Connecting to an External Device Change Notes: *1 transmit/receive if program change switch is on. *2 transmit/receive if control change switch is on. *3 transmit/receive if parameter change switch is on. Mode 1 : OMNI ON , POLY Mode 3 : OMNI OFF, POLY Mode 2 : OMNI ON ,MONO Mode 4 : OMNI OFF,MONO Ø ˛ : Yes : No DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 37 Foreword References Display Messages The [ERROR] and [PEAK] indicators on the front panel of the DME Satellite indicate error and warning messages. Introduction to the DME Satellite Error Messages Indicator Error Flashing A system error has occurred. Execute the “Initialize DME” operation, then restart it. If the error indicators are still indicating the error, execute the “Delete All Data” initialization. If the problem persists, contact a Yamaha dealer. Data inside the internal flash memory has been erased. The firmware update operation may have failed. Use DME Designer to execute the Recovery update operation. If the problem persists, contact a Yamaha dealer. The internal battery is completely discharged or not installed. If you turn off the power to the unit, the current settings will be lost and reset to the default values. Stop operating the unit, and contact a Yamaha dealer regarding battery replacement. A scene recall attempt has failed. Use DME Designer to recall the scene again. If the problem persists, contact a Yamaha dealer. Audio is not input or output and is muted due to insufficient DSP resources. This error sometimes occurs if you try to operate a configuration at 96 kHz that has been created with a word clock of 48 kHz. To operate a configuration at any word clock setting, use DME Designer to create a configuration with the word clock set to 96 kHz. The network is not communicating properly. Connect the Ethernet cables properly, and make sure that the network devices are operating correctly. Duplicate IP addresses. Connect your computer to the DME Satellite via USB, then set a unique IP address. The DME Satellite contains data for a different device group or no data. Send data appropriate for the actual device configuration from DME Designer. Lit Controls and Connectors Flashing Lit Flashing Connecting to a Computer Lit Flashing Action Lit Audio I/O Connection Lit Flashing Lit Flashing Connecting to an External Device Lit Flashing Lit Other Functions Flashing Warning Messages References Indicator Flashing rapidly Flashing slow 38 Error Action The internal battery is almost discharged. Your data may be lost. If you turn off the power to the unit, the current settings may be lost and reset to the default values. Stop operating the unit, and contact a Yamaha dealer regarding battery replacement. The backup battery voltage is low. This does not affect the operation of the unit. However, if you continue using the unit, the settings may be lost and reset to the default values. Contact a Yamaha dealer regarding battery replacement at your earliest convenience. DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual Foreword References External Clock Normal Rate: 44.1/48 kHz (±0.1%) Double Rate: 88.2/96 kHz (±0.1%) Internal Clock Normal Rate: 48 kHz (±50ppm) Double Rate: 96 kHz (±50ppm) Maximum Voltage Gain 40W Dimensions (HxDxW) 44x361x480 mm 4.5kg operating: 5 to 40˚C storage: –20 to 60˚C Temperature range Connecting to a Computer AC Power cord, Mini Euro plug(16P)x1, Euro plug(3P)x8, Owner’s Manual, Rubber feetx4 Include Accessories Electrical Characteristics Output impedance of signal generator: 150 Ω DME8i-ES : Measured with DME8o-ES DME8o-ES : Measured with DME8i-ES DME4io-ES: Measured with DME4io-ES Frequency Response fs=48kHz@20Hz–20kHz, reference to the nominal output level @1kHz fs=96kHz@20Hz–40kHz, reference to the nominal output level @1kHz <DME8i-ES> Input Output RL INPUT 1–8 OUTPUT 1–8 600Ω Controls and Connectors Net Weight CONDITIONS MIN TYP MAX UNITS input level: –60dBu, GAIN: –60dB –1.5 0.0 +0.5 dB input level: +10dBu, GAIN: +10dB –1.5 0.0 +0.5 dB <DME8o-ES> Input Output RL CONDITIONS MIN TYP MAX UNITS INPUT 1–8 OUTPUT 1–8 600Ω input level: +10dBu, GAIN: +10dB –1.5 0.0 +0.5 dB Output RL Audio I/O Connection Miscellaneous Gain: –60dB, RL:600Ω, 64dB INPUT to OUTPUT Power Consumption Connecting to an External Device Sampling Frequency Introduction to the DME Satellite General Specifications Input INPUT 1–4 OUTPUT 1–4 CONDITIONS MIN TYP MAX UNITS input level: –60dBu, GAIN: –60dB –1.5 0.0 +0.5 dB input level: +10dBu, GAIN: +10dB –1.5 0.0 +0.5 dB CONDITIONS MIN TYP MAX UNITS input level: –60dBu, GAIN: –60dB → output level: +4.0dBu (typ.) –2.0 0 +2.0 dB input level: +10dBu, GAIN: +10dB → output level: +4.0dBu (typ.) –2.0 0 +2.0 dB 600Ω Gain Error Other Functions <DME4io-ES> @1kHz Input INPUT 1–8 Output OUTPUT 1–8 RL 600Ω DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual References <DME8i-ES> 39 Foreword References <DME8o-ES> Introduction to the DME Satellite Input Output RL CONDITIONS MIN TYP MAX UNITS INPUT 1–8 OUTPUT 1–8 600Ω input level: +10dBu, GAIN: +10dB → output level: +4.0dBu (typ.) –2.0 0 +2.0 dB Output RL CONDITIONS MIN TYP MAX UNITS input level: –60dBu, GAIN: –60dB → output level: +4.0dBu (typ.) –2.0 0 +2.0 dB input level: +10dBu, GAIN: +10dB → output level: +4.0dBu (typ.) –2.0 0 +2.0 dB <DME4io-ES> Input INPUT 1–4 OUTPUT 1–4 600Ω Controls and Connectors Total Harmonic Distortion fs=48kHz or 96kHz <DME8i-ES> Input Connecting to a Computer INPUT 1–8 Output OUTPUT 1–8 RL 600Ω CONDITIONS TYP Audio I/O Connection Connecting to an External Device Other Functions MAX UNITS +4dB@20Hz–20kHz (fs=48kHz), 20Hz–40kHz (fs=96kHz), GAIN: –60dB 0.1 % +4dB@20Hz–20kHz (fs=48kHz), 20Hz–40kHz (fs=96kHz), GAIN: +10dB 0.05 % +22dB@1kHz, GAIN: +10dB 0.015 (fs=48kHz) 0.007 (fs=96kHz) % MAX UNITS +4dB@20Hz–20kHz (fs=48kHz), 20Hz–40kHz (fs=96kHz), GAIN: +10dB 0.05 % +22dB@1kHz, GAIN: +10dB 0.015 (fs=48kHz) 0.007 (fs=96kHz) % MAX UNITS +4dB@20Hz–20kHz (fs=48kHz), 20Hz–40kHz (fs=96kHz), GAIN: –60dB 0.1 % +4dB@20Hz–20kHz (fs=48kHz), 20Hz–40kHz (fs=96kHz), GAIN: +10dB 0.05 % +22dB@1kHz, GAIN: +10dB 0.015 (fs=48kHz) 0.007 (fs=96kHz) % <DME8o-ES> Input INPUT 1–8 Output OUTPUT 1–8 RL CONDITIONS MIN TYP 600Ω <DME4io-ES> Input INPUT 1–4 Output OUTPUT 1–4 RL 600Ω CONDITIONS * Total Harmonic Distortion is measured with a 18dB/octave filter @80kHz. References 40 MIN DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual MIN TYP Foreword References Hum&Noise fs=48kHz or 96kHz, EIN=Equivalent Input Noise Input Output RL CONDITIONS MIN Rs=150Ω, GAIN: –60dB All input & output level controls: 0dB INPUT 1–8 OUTPUT 1–8 600Ω TYP MAX UNITS –128 EIN –127 EIN dBu –64 Rs=150Ω, GAIN: +10dB All input & output level controls: 0dB dBu –82 –79 dBu TYP MAX UNITS –82 –79 dBu TYP MAX UNITS –128 EIN –127 EIN dBu Introduction to the DME Satellite <DME8i-ES> Input Output RL CONDITIONS INPUT 1–8 OUTPUT 1–8 600Ω Rs=150Ω, GAIN: +10dB All input & output level controls: 0dB Output RL CONDITIONS MIN Controls and Connectors <DME8o-ES> Input MIN Rs=150Ω, GAIN: –60dB All input & output level controls: 0dB INPUT 1–4 OUTPUT 1–4 600Ω –64 Rs=150Ω, GAIN: +10dB All input & output level controls: 0dB –82 dBu –79 dBu Connecting to a Computer <DME4io-ES> fs=48kHz or 96kHz <DME8i-ES/DME8o-ES> RL CONDITIONS 600Ω GAIN: +10dB Input Output RL CONDITIONS INPUT 1–4 OUTPUT 1–4 600Ω GAIN: +10dB MIN TYP MAX 106 UNITS dB <DME4io-ES> MIN TYP MAX 106 UNITS dB * Dynamic range are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave attenuation. Crosstalk@1kHz reference to the level of output N <DME8i-ES/DME8o-ES> from to CONDITIONS INPUT N OUTPUT (N–1) or (N+1) N = 1–8, GAIN: +10dB MIN TYP MAX UNITS –80 dB MAX UNITS –80 dB <DME4io-ES> from to CONDITIONS INPUT N OUTPUT (N–1) or (N+1) N = 1–4, GAIN: +10dB MIN TYP Connecting to an External Device Output OUTPUT 1–8 Other Functions Input INPUT 1–8 References Dynamic Range Audio I/O Connection * Hum & Noise are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave attenuation. * Crosstalk is measured with a 18dB/octave filter @80kHz DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 41 Foreword References LED Level Meter <DME8i-ES> METERING POINT CONDITIONS MIN TYP MAX UNITS Introduction to the DME Satellite PEAK red LED: ON –3 dBFs SIGNAL green LED: ON –40 dBFs INPUT 1–8 <DME8o-ES> METERING POINT CONDITIONS MIN TYP MAX UNITS Controls and Connectors PEAK red LED: ON –3 dBFs SIGNAL green LED: ON –40 dBFs OUTPUT 1–8 <DME4io-ES> METERING POINT CONDITIONS MIN TYP MAX UNITS INPUT 1–4 OUTPUT 1–4 PEAK red LED:ON –3 dBFs SIGNAL green LED:ON –40 dBFs Connecting to a Computer Signal Delay from to CONDITIONS MIN Analog input of Primary Master Analog output of the slave via EtherSound @ 48kHz TYP MAX UNITS 2 msec Audio I/O Connection Input/Output Characteristics ANALOG INPUT CHARACTERISTICS Input Terminals Connecting to an External Device <DME8i-ES> CH INPUT 1–8 <DME4io-ES> CH INPUT 1–4 GAIN Actual Load Impedance For Use With Nominal 3kΩ 50–600Ω Mics & 600Ω Lines Input Level –60dB +10dB Connector Nominal Max.before clip –60dBu (0.775mV) –40dBu (7.75mV) +10dBu (2.45V) +30dBu (24.5V) EUROBLOCK (5.08mm pitch) *1.In these specifications, 0dBu is referenced to 0.775 Vrms. *2.All AD converters are 24-bit linear, 128-times oversampling (Fs=48kHz)/64-times oversampling (Fs=96kHz). *3.+48V DC (Phantom power) is supplied to CH INPUT EUROBLOCK connectors via each individual software controlled switch. Other Functions ANALOG OUTPUT CHARACTERISTICS Output Terminals Actual Source Impedance For Use With Nominal 75Ω 600Ω Lines Output level Nominal Max. before clip +4dBu (1.23 V) +24dBu(12.28V) <DME8o-ES> CH OUTPUT 1–8 References <DME4io-ES> CH OUTPUT 1–4 Connector EUROBLOCK (5.08mm pitch) *1.In these specifications, 0dBu is referenced to 0.775 Vrms. *2.All DA converters are 24-bit linear, 128-times oversampling (Fs=48kHz)/64-times oversampling (Fs=96kHz). DIGITAL INPUT & OUTPUT CHARACTERISTICS 42 Terminal Format Data length Level Audio Connector EtherSound EtherSound 24bit 100Base-TX 16ch input/16ch output @ 48kHz 8ch input/8ch output @ 96kHz RJ-45x2 DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual Foreword References Terminal Format Level Connector IN – 0–5V EUROBLOCK *1 (3.5mm pitch) OUT – TTL +V – 5V Ethernet IEEE802.3 10Base-T/100Base-TX RJ-45 USB USB 1.1 Function – Type B REMOTE RS-232C/RS-422 RS-232C/RS-422 D-SUB 9P (Male) GPI Controls and Connectors *1 Inputs: 8 channels, Outputs: 4 channels Inputs: Not apply 2 wire Fader mode Outputs: Imax/pin = 16mA Outputs: VH = 2.5V(min.), VL = 0.6V(max.) Introduction to the DME Satellite CONTROL I/O CHARACTERISTICS 2 TxD– 3 RxD+ 4 Unused 5 Unused 6 RxD– 7 Unused 8 Unused Connecting to an External Device TxD+ Other Functions 1 Audio I/O Connection Connection References Pin Connecting to a Computer [NETWORK] Connector (100Base-TX Ethernet, RJ-45) DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 43 Foreword References Dimensions Connecting to a Computer 3 361 Controls and Connectors 354 (4) Introduction to the DME Satellite 480 Audio I/O Connection Connecting to an External Device 44 Rubber feet are included in the package. Unit: mm * Specifications and descriptions in this owner’s manual are for information purpose only. Yamaha Corp. reserves the right to charge or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. European models Purchaser/User Information specified in EN55103-1 and EN55103-2. Inrush Current: 35A Conforms to Environments: E1,E2,E3 and E4. Other Functions References 44 1 440 DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual Foreword References Warning Messages ............................. 38 [AC IN] Connector ............................16 [MASTER] Indicator ........................ 14 Analog Audio Connection ..................25 MIDI Data Format ........................... 34 Z area ......................................................9 MIDI Implementation Chart ............ 37 zones ................................................... 9 C N Components ........................................9 [NETWORK] Connector ........... 16, 43 Configuration .......................................9 [NETWORK] Indicator .................... 14 CP4SW, CP4SF, and CP1SF .............32 Network Settings ............................... 19 D O Delete All Data ..................................31 octet .................................................. 19 device group .........................................9 Options ............................................. 32 Digital Audio Connection ..................24 [OUTPUT] Connectors .................... 17 Dimensions ........................................44 Dip Switch .........................................16 P Display Messages ................................38 parameters ........................................... 9 DME4io-ES .........................................8 [PEAK] Indicators ............................. 15 DME8i-ES ...........................................8 [POWER] Indicator .......................... 15 DME8o-ES ..........................................8 [POWER] Switch .............................. 15 E Precautions for Using a Rack-mounted DME Satellite ............................. 17 Electrical Characteristics .....................39 preset parameters ................................. 9 Ethernet Connection ..........................20 Remote Connection .......................... 26 EtherSound Connection .....................28 [REMOTE] Connector ..................... 17 EtherSound Connectors ...............24, 28 RS-232C ........................................... 16 EtherSound [IN]/[OUT] Connectors 17 RS-422 .............................................. 16 Euroblock plug connection ................25 S F Scene ................................................. 10 Firmware Version .................................7 Setting the IP address ........................ 19 [SIGNAL] Indicators ......................... 15 G Signal Types ...................................... 11 General Specifications ........................39 Straight and Crossover Cable Wiring 44 GPI Connection .................................30 System Examples ............................... 12 [GPI] Connector ................................17 Ground Screw ....................................16 group master ........................................9 T Troubleshooting ................................ 33 [TX/RX] Indicator ............................ 15 I ICP1 ..................................................32 U Initialize DME ...................................31 USB Connection ............................... 18 Initializing ..........................................31 [USB] Connector .............................. 14 [INPUT] & [OUTPUT] Connectors 25 User Defined buttons (User Defined parameters) ................................... 9 [INPUT] Connectors .........................17 Connecting to an External Device R Other Functions Error Messages ...................................38 References [ERROR] Indicator ............................15 Controls and Connectors W Master and slave setting ..................... 19 Connecting to a Computer M About DME Designer ........................13 Audio I/O Connection A Introduction to the DME Satellite Index Input/Output Characteristics .............42 DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 45 Foreword Introduction to the DME Satellite Controls and Connectors Connecting to a Computer Audio I/O Connection Connecting to an External Device Other Functions References DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual 46 MEMO For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A. Tel: 714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México S.A. de C.V. Calz. Javier Rojo Gómez #1149, Col. Guadalupe del Moral C.P. 09300, México, D.F., México Tel: 55-5804-0600 Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. ASIA POLAND Yamaha Music Europe GmbH Branch Sp.z o.o. Oddzial w Polsce ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland Tel: 022-868-07-57 THE PEOPLE’S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co.,Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: 021-6247-2211 THE NETHERLANDS/ BELGIUM/LUXEMBOURG Yamaha Music Europe Branch Benelux Clarissenhof 5-b, 4133 AB Vianen, The Netherlands Tel: 0347-358 040 FRANCE Yamaha Musique France BP 70-77312 Marne-la-Vallée Cedex 2, France Tel: 01-64-61-4000 Yamaha Musical do Brasil Ltda. Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi, CEP 04534-013 Sao Paulo, SP. BRAZIL Tel: 011-3704-1377 PT. Yamaha Music Indonesia (Distributor) PT. Nusantik Gedung Yamaha Music Center, Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: 21-520-2577 ITALY Yamaha Musica Italia S.P.A. Combo Division Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 KOREA Yamaha Music Korea Ltd. 8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong, Kangnam-Gu, Seoul, Korea Tel: 080-004-0022 Yamaha Música Ibérica, S.A. Ctra. de la Coruna km. 17, 200, 28230 Las Rozas (Madrid), Spain Tel: 91-639-8888 MALAYSIA Yamaha Music Malaysia, Sdn., Bhd. Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-78030900 SWEDEN ARGENTINA Yamaha Music Latin America, S.A. Sucursal de Argentina Olga Cossettini 1553, Piso 4 Norte Madero Este-C1107CEK Buenos Aires, Argentina Tel: 011-4119-7000 PANAMA AND OTHER LATIN AMERICAN COUNTRIES/ CARIBBEAN COUNTRIES Yamaha Music Latin America, S.A. Torre Banco General, Piso 7, Urbanización Marbella, Calle 47 y Aquilino de la Guardia, Ciudad de Panamá, Panamá Tel: +507-269-5311 EUROPE THE UNITED KINGDOM Yamaha Music U.K. Ltd. Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, England Tel: 01908-366700 Yamaha Scandinavia AB J. A. Wettergrens Gata 1, Box 30053 S-400 43 Göteborg, Sweden Tel: 031 89 34 00 SWITZERLAND/LIECHTENSTEIN Yamaha Music Europe GmbH Branch Switzerland in Zürich Seefeldstrasse 94, 8008 Zürich, Switzerland Tel: 01-383 3990 AUSTRIA Yamaha Music Europe GmbH Branch Austria Schleiergasse 20, A-1100 Wien, Austria Tel: 01-60203900 CZECH REPUBLIC/SLOVAKIA/ HUNGARY/SLOVENIA Yamaha Music Europe GmbH Branch Austria Schleiergasse 20, A-1100 Wien, Austria Tel: 01-602039025 SINGAPORE Yamaha Music Asia Pte., Ltd. #03-11 A-Z Building 140 Paya Lebor Road, Singapore 409015 Tel: 747-4374 DENMARK YS Copenhagen Liaison Office Generatorvej 6A, DK-2730 Herlev, Denmark Tel: 44 92 49 00 TAIWAN Yamaha KHS Music Co., Ltd. 3F, #6, Sec.2, Nan Jing E. Rd. Taipei. Taiwan 104, R.O.C. Tel: 02-2511-8688 NORWAY Norsk filial av Yamaha Scandinavia AB Grini Næringspark 1, N-1345 Østerås, Norway Tel: 67 16 77 70 THAILAND RUSSIA Yamaha Music (Russia) Room 37, bld. 7, Kievskaya street, Moscow, 121059, Russia Tel:495 626 5005 OTHER EUROPEAN COUNTRIES Yamaha Music Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: +49-4101-3030 GERMANY Yamaha Music Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: 04101-3030 Yamaha Music India Pvt. Ltd. 5F Ambience Corporate Tower Ambience Mall Complex Ambience Island, NH-8, Gurgaon-122001, Haryana, India Tel: 0124-466-5551 INDONESIA SPAIN/PORTUGAL BRAZIL INDIA AFRICA Yamaha Corporation, Asia-Pacific Sales & Marketing Group Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2303 MIDDLE EAST TURKEY/CYPRUS Yamaha Music Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: 04101-3030 OTHER COUNTRIES Yamaha Music Gulf FZE LOB 16-513, P.O.Box 17328, Jubel Ali, Dubai, United Arab Emirates Tel: +971-4-881-5868 Siam Music Yamaha Co., Ltd. 4, 6, 15 and 16th floor, Siam Motors Building, 891/1 Rama 1 Road, Wangmai, Pathumwan, Bangkok 10330, Thailand Tel: 02-215-2626 OTHER ASIAN COUNTRIES Yamaha Corporation, Asia-Pacific Sales & Marketing Group Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2303 OCEANIA AUSTRALIA Yamaha Music Australia Pty. Ltd. Level 1, 99 Queensbridge Street, Southbank, Victoria 3006, Australia Tel: 3-9693-5111 COUNTRIES AND TRUST TERRITORIES IN PACIFIC OCEAN Yamaha Corporation, Asia-Pacific Sales & Marketing Group Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2303 HEAD OFFICE Yamaha Corporation, Pro Audio Division Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2441 PA26' Yamaha Pro Audio global web site: http://www.yamahaproaudio.com/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ U.R.G., Pro Audio Division © 2007-2010 Yamaha Corporation 008IPTO-D0 Printed in Japan WK01190
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Yamaha DME8o-ES El manual del propietario

Categoría
Sintetizador
Tipo
El manual del propietario
Este manual también es adecuado para