Yamaha DME-64N Manual de usuario

Marca: Yamaha

Modelo: DME-64N

Categoría: Mezcladores de audio

Tipo: Manual de usuario

Owner’s Manual

DIGITAL MIXING ENGINE

The above warning is located on the top of the unit.

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11 Only use attachments/accessories specified by

the manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table

specified by the manufacturer,

or sold with the apparatus.

When a cart is used, use

caution when moving the cart/

apparatus combination to avoid

injury from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord

or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modifications not

expressly approved by Yamaha may void your authority, granted

by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digi-

tal devices. Compliance with these requirements provides a rea-

sonable level of assurance that your use of this product in a

residential environment will not result in harmful interference with

other electronic devices. This equipment generates/uses radio fre-

quencies and, if not installed and used according to the instruc-

tions found in the users manual, may cause interference harmful to

the operation of other electronic devices. Compliance with FCC

regulations does not guarantee that interference will not occur in all

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

installations. If this product is found to be the source of interfer-

ence, which can be determined by turning the unit “OFF” and

“ON”, please try to eliminate the problem by using one of the fol-

lowing measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed

by Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in accor-

dance with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the terminals

in your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be connected

to the terminal in the plug which is marked by the letter E or by the

safety earth symbol or colored GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the terminal

which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the termi-

nal which is marked with the letter L or coloured RED.

• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd. (3 wires)

This product contains a battery that contains perchlorate material.

Perchlorate Material—special handling may apply,

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

• This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (Perchlorate)

NEDERLAND / THE NETHERLANDS

• Dit apparaat bevat een lithium batterij voor geheugen back-up.

• This apparatus contains a lithium battery for memory back-up.

• Raadpleeg uw leverancier over de verwijdering van de batterij op

het moment dat u het apparaat ann het einde van de levensduur of

gelieve dan contact op te nemen met de vertegenwoordiging van

Yamaha in uw land.

• For the removal of the battery at the moment of the disposal at the

end of life please consult your retailer or Yamaha representative

office in your country.

• Gooi de batterij niet weg, maar lever hem in als KCA.

• Do not throw away the battery. Instead, hand it in as small chemical

waste.

(lithium disposal)

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning

må kun ske med batteri af samme fabrikat og type. Levér det brugte

batteri tilbage til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma batterityp

eller en ekvivalent typ som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo

ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty

paristo valmistajan ohjeiden mukaisesti.

(lithium caution)

In Finland: Laite on liitettävä suojamaadoituskoskettimilla varust-

ettuun pistorasiaan.

In Norway: Apparatet må tilkoples jordet stikkontakt.

In Sweden: Apparaten skall anslutas till jordat uttag.

(class I hokuo)

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park,

Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Digital Mixing Engine

Model Name : DME64N / DME24N

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including inter-

ference that may cause undesired operation.

See user manual instructions if interference to radio reception is sus-

pected.

(FCC DoC)

DME64N/DME24N Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from

electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited

to, the following:

• Only use the voltage specified as correct for the device. The required

voltage is printed on the name plate of the device.

• Use only the supplied power cord/plug.

• Do not place the power cord near heat sources such as heaters or

radiators, and do not excessively bend or otherwise damage the cord,

place heavy objects on it, or place it in a position where anyone could walk

on, trip over, or roll anything over it.

• Be sure to connect to an appropriate outlet with a protective grounding

connection. Improper grounding can result in electrical shock.

• Check the electric plug periodically and remove any dirt or dust which may

have accumulated on it.

• The device contains no user-serviceable parts. Do not open the device or

attempt to disassemble the internal parts or modify them in any way. If it

should appear to be malfunctioning, discontinue use immediately and

have it inspected by qualified Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet

conditions,or place on it any containers (such as vases, bottles or glasses)

containing liquids which might spill into any openings.

If any liquid such as water seeps into the device, turn off the power

immediately and unplug the power cord from the AC outlet. Then have the

device inspected by qualified Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning item

may fall over and cause a fire.

• When one of the following problems occur, immediately turn off the power

switch and disconnect the electric plug from the outlet. Then have the

device inspected by Yamaha service personnel.

• The power cord or plug becomes frayed or damaged.

• It emits unusual smells or smoke.

• Some object has been dropped into the instrument.

• There is a sudden loss of sound during use of the device.

• If this device should be dropped or damaged, immediately turn off the

power switch, disconnect the electric plug from the outlet, and have the

device inspected by qualified Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or

damage to the device or other property. These precautions include, but are not limited to, the following:

• Remove the electric plug from the outlet when the device is not to be used

for extended periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always hold

the plug itself and not the cord. Pulling by the cord can damage it.

• Before moving the device, remove all connected cables.

• When setting up the device, make sure that the AC outlet you are using is

easily accessible. If some trouble or malfunction occurs, immediately turn

off the power switch and disconnect the plug from the outlet. Even when

the power switch is turned off, electricity is still flowing to the product at

the minimum level. When you are not using the product for a long time,

make sure to unplug the power cord from the wall AC outlet.

• Do not place the device in an unstable position where it might accidentally

fall over.

• Do not block the vents. This device has ventilation holes at the front and

rear to prevent the internal temperature from rising too high. In particular,

do not place the device on its side or upside down, or place it in any

poorly-ventilated location, such as a bookcase or closet.

• Do not place the device in a location where it may come into contact with

corrosive gases or salt air. Doing so may result in malfunction.

• Before connecting the device to other devices, turn off the power for all

devices. Before turning the power on or off for all devices, set all volume

levels to minimum.

Power supply/Power cord

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/Power cord

Location

Connections

(5)-1 1/2

DME64N/DME24N Owner’s Manual

• Remove the power plug from the AC outlet when cleaning the device.

• Do not insert your fingers or hand in any gaps or openings on the device

(vents, ports, etc.).

• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into

any gaps or openings on the device (vents, ports, etc.) If this happens,

turn off the power immediately and unplug the power cord from the AC

outlet. Then have the device inspected by qualified Yamaha service

personnel.

• Do not use the device or headphones for a long period of time at a high or

uncomfortable volume level, since this can cause permanent hearing loss.

If you experience any hearing loss or ringing in the ears, consult a

physician.

• Do not rest your weight on the device or place heavy objects on it, and

avoid use excessive force on the buttons, switches or connectors.

This device has a built-in backup battery that maintains data in

internal memory even when the device’s power is switched off. The

backup battery will eventually become depleted, however, and when

that happens the contents of the internal memory will be lost.* To

prevent loss of data be sure to replace the backup battery before it

becomes fully depleted. When the remaining capacity of the backup

battery becomes so low that it needs to be replaced a “Low Battery”

or “No Battery” message will appear on the display during operation

or when the device is powered on. If either of these messages

appears do not turn off the power and immediately transfer any data

you want to save to a computer or other external storage device,

then have qualified Yamaha service personnel replace the backup

battery. The average life of the internal backup battery is

approximately 5 years, depending on operating conditions.

* Data items maintained in the internal memory by the backup

battery are as follows:

• Current scene parameters and number.

• Device parameters (SLOT, HA, UTILITY, Master Mute/Level, etc.).

• Event log.

Data items other than those described above are stored in memory

that does not require backup power, and will be retained even if the

backup battery fails.

Do not turn the [POWER] switch on and off repeatedly and rapidly. Be sure to wait six seconds or more between turning the

power to the unit off and then on.

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over

time. Consult qualified Yamaha service personnel about replacing defective components.

NOTICE

To avoid the possibility of damage to the product, data or other property, follow the notices below.

 Handling and Maintenance

• Do not use the device in the vicinity of a TV, radio, stereo equipment,

mobile phone, or other electric devices. Otherwise, the device, TV, or radio

may generate noise.

• Condensation can occur in the device due to rapid, drastic changes in

ambient temperature-when the device is moved from one location to

another, or air conditioning is turned on or off, for example. Using the

device while condensation is present can cause damage. If there is reason

to believe that condensation might have occurred, leave the device for

several hours without turning on the power until the condensation has

completely dried out.

• Do not expose the device to excessive dust or vibrations, or extreme cold

or heat (such as in direct sunlight, near a heater, or in a car during the day)

to prevent the possibility of panel disfiguration or damage to the internal

components.

• Avoid setting all equalizer controls and faders to their maximum.

Depending on the condition of the connected devices, doing so may cause

feedback and may damage the speakers.

Information

 About this manual

• The illustrations in this document are for instructional purposes, and may

appear somewhat different from the actual equipment.

• The bitmap fonts used in this device have been provided by and are the

property of Ricoh Co., Ltd.

• CobraNet and Peak Audio are trademarks of Cirrus Logic, Inc.

• Ethernet is a trademark of Xerox Corporation.

• All other trademarks are the property of their respective holders and are

hereby acknowledged.

Maintenance

Handling caution

Backup battery

Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.

(5)-1 2/2

Foreword

DME64N/DME24N Owner’s Manual

Foreword

Thank you for choosing a Yamaha DME64N/24N Digital Mixing Engine.

Using the supplied DME Designer software, the DME64N and DME24N can be easily

configured to handle a wide range of audio processing applications – institutional audio

installations, sub-mixing, speaker system control, matrix and routing, multi-effect processing,

and much more.

In order to take full advantage of the features and performance provided by the DME64N/24N,

we urge you to read this owner’s manual thoroughly before use, and keep it in a safe place for

future reference.

The Yamaha Pro Audio web site is at: http://www.yamahaproaudio.com/

DME64N/DME24N Owner’s Manual

Foreword 8

Accessories (Please make sure the following

items are included in the package.). . . . . . . . . . . 8

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

About the Product Names . . . . . . . . . . . . . . . . . . 8

About the Firmware Version. . . . . . . . . . . . . . . . . 8

Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connecting the AC power cord . . . . . . . . . . . . . . . . . . . . . .8

Turning the power on and off . . . . . . . . . . . . . . . . . . . . . . .8

Introduction to the DME64N/24N 9

Differences between DME64N/24N . . . . . . . . . . . 9

DME64N/24N Features . . . . . . . . . . . . . . . . . . . . . 9

Audio System Network . . . . . . . . . . . . . . . . . . . . . 9

Glossary for the DME64N/24N . . . . . . . . . . . . . . . 9

Signal Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

System Examples . . . . . . . . . . . . . . . . . . . . . . . . 12

About DME Designer. . . . . . . . . . . . . . . . . . . . . . 13

The Controls and Connectors 14

Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Setup 18

Setup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . 18

I/O Card Installation. . . . . . . . . . . . . . . . . . . . . . . 20

Compatible I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

I/O Card Installation Procedure. . . . . . . . . . . . . . . . . . . . .21

Connecting to a Computer 22

USB Connection . . . . . . . . . . . . . . . . . . . . . . . . . 22

Ethernet Connection ([NETWORK] Connector)

.23

Audio I/O Connection 26

Analog Audio Connection ([IN] and [OUT] Connectors)

(DME24N only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

I/O Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Connecting to an External Device 28

Remote Connection ([REMOTE] Connector) . . 28

Controlling external head amplifiers from the DME64N/24N

.28

Controlling a DME24N’s internal head amps from a digital mixer

.29

Controlling the DME64N/24N from an external device . . .29

Network Connection ([NETWORK] Connectors)

.30

MIDI Connection ([MIDI] Connectors) . . . . . . . . 30

Cascade Connection ([Cascade] Connectors)

(DME64N only) . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

WORD CLOCK Connection ([WORD CLOCK]

Connectors) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

GPI Connection ([GPI] Connectors). . . . . . . . . . 33

Panel Operation and Displays 34

Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . 34

Main Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Parameter Edit Displays. . . . . . . . . . . . . . . . . . . 36

Editing User Defined Button . . . . . . . . . . . . . . . . . . . . . . 38

Mute Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Output Level Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Scene Recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Scene Store. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Spectrum Display . . . . . . . . . . . . . . . . . . . . . . . . 41

Level Meter Display . . . . . . . . . . . . . . . . . . . . . . 42

Initializing the DME64N/DME24N. . . . . . . . . . . . 42

Utility Displays . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Items accessible via the Utility display. . . . . . . . . . . . . . . 43

Utility Display Operation . . . . . . . . . . . . . . . . . . . . . . . . . 45

Info Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Network Settings (Net) Page . . . . . . . . . . . . . . . . . . . . . . 46

Display Setup (Disp) Page. . . . . . . . . . . . . . . . . . . . . . . . 46

Security Setup (Lock) Page . . . . . . . . . . . . . . . . . . . . . . . 47

Miscellaneous Setup (Misc) Page . . . . . . . . . . . . . . . . . . 48

Remote Control Setup (Remote) Page . . . . . . . . . . . . . . 48

MIDI Setup (MIDI) Page . . . . . . . . . . . . . . . . . . . . . . . . . 49

Word Clock Setup (WCLK) Page. . . . . . . . . . . . . . . . . . . 50

Slot Information (Slot) Page. . . . . . . . . . . . . . . . . . . . . . . 51

GPI Setup (GPI) Page . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Head Amplifier Setup (HA) Page . . . . . . . . . . . . . . . . . . . 52

Cascade Setup (CASCAD) Page . . . . . . . . . . . . . . . . . . 53

Check Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

References 55

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

ICP1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

CP4SW, CP4SF, and CP1SF . . . . . . . . . . . . . . . . . . . . . 55

Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . 56

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 59

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Input/Output Characteristics . . . . . . . . . . . . . . . 61

Control I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Connector Pin Assign . . . . . . . . . . . . . . . . . . . . 63

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

MIDI Data Format . . . . . . . . . . . . . . . . . . . . . . . . 66

MIDI Data Format . . . . . . . . . . . . . . . . . . . . . . . . 70

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Index 73

Contents

Foreword

Introduction to

the DME64N/24N

The Controls

and Connectors

Setup

Audio I/O

Connection

Connecting to

a Computer

Connecting to an

External Device

Panel Operation

and Displays

References

Foreword

Accessories (Please make sure the following items are included in the package.)

DME64N/DME24N Owner’s Manual

Thank you for choosing a Yamaha DME64N/24N Digital Mixing Engine.

In order to take full advantage of the features and performance provided by the DME64N/24N, we urge you to read this

owner’s manual thoroughly before connecting or using the unit. Keep this manual in a safe place for future reference.

Accessories (Please make

sure the following items are

included in the package.)

• DME64N/DM24N Owner’s Manual

(This document)

• AC power cord

• AC plug clamp

• Euroblock plug (16P) x 2

• Euroblock plug (8P) x 4 (DME64N only)

• Euroblock plug (3P) x 16 (DME24N only)

Options

Control Panels

• ICP1 Intelligent Control Panel

• CP4SW Control Panel

• CP4SF Control Panel

• CP1SF Control Panel

About the Product Names

In this manual, models DME64N, DME24N, DME8i-C,

DME8o-C, DME4io-C, DME8i-ES, DME8o-ES and

DME4io-ES are categorized as DME series, and models

DME8i-C, DME8o-C, DME4io-C, DME8i-ES, DME8o-ES

and DME4io-ES are all called the “DME Satellite”.

About the Firmware Version

You can download the latest firmware from the following

Yamaha website.

http://www.yamahaproaudio.com/downloads/

Preparation

Connecting the AC power cord

First plug the female-connector end of the AC cord into

the [AC IN] socket on the rear panel of the DME64N/

24N, then plug the male plug into an appropriate AC

mains outlet.

Be sure to use the voltage specified for the device.

Turning the power on and off

1. Press the [POWER] switch to turn on the

power to the DME64N/24N.

2. Press the [POWER] switch again to turn off

the power.

Foreword

NOTE

For more information on your Control Panel, refer to the

owner’s manual that came with the Control Panel, as

well as the DME Designer Owner’s Manual.

Be sure to turn all devices OFF before

connecting AC mains power.

To prevent the initial power-on surge from

generating a large noise spike or damaging

your speaker system, turn the devices on in

the following order: audio sources, mixer

(such as M7CL or PM5D), DME64N/24N, and

finally power amplifiers.

Reverse this order when turning power off.

NOTE

The DME64N/24N remembers scene settings when you

turn off the power.

When you turn on the power to the DME64N/24N, it will

start up with the same scene settings.

You can set up the DME64N/24N so that at the startup it

will recall the scene selected before you turned off the

power to the device. (page 48)

Do NOT turn off the power to the DME64N/24N

while it is receiving data from DME Designer

or while it is being manipulated from an

external device. Otherwise, a malfunction may

occur.

Even when the power switch is turned off,

electricity is still flowing to the product all the

minimum level. When you are not using the

product for a long time, make sure to unplug

the power cord from the wall AC outlet.

CAUTION

Introduction to the DME64N/24N

Differences between DME64N/24N

DME64N/DME24N Owner’s Manual

Differences between DME64N/24N

The DME64N has four I/O card slots, while the DME24N has one I/O card slot and eight channels of built-

in analog audio I/O.

A single I/O card can handle up to 16 channels of audio I/O, so the DME64N can handle a maximum of 64

audio I/O channels. The DME24N can handle up to 24 audio I/O channels.

The DME64N has approximately double the DSP processing power of the DME24N.

DME64N/24N Features

In addition to basic mixing and matrix output functions, the DME64N/24N includes a equalizers, compres-

sors, delay, etc. – that can be patched together via DME Designer to configure just about any audio system

you need.

Audio System Network

Multiple DME series units that are interconnected in a network via Ethernet function as a single audio sys-

tem.

In a DME audio system, a group of the same models that can be operated in sync is called a “device group;”

audio processing divisions that accommodate multiple device groups are called “zones;” and the entire

area serviced by the acoustic system is called an “area.”

Each device group always includes one DME series unit that functions as the “group master” and controls

all other DME series units in the same device group.

If a computer is connected to the network, you can use the computer to control an entire device group via

the group master.

Glossary for the DME64N/24N

This section explains terminology specific to the DME64N/24N.

Components and parameters

The individual audio processing modules (equalizers, compressors, etc.) are called “components.”

External head amplifier control modules are also available as components.

Changing the parameters of components enables control over the operation of the components.

Configuration

A “configuration” is a complete set of components for constructing an audio system.

Each configuration determines the audio function(s) of the corresponding DME64N/24N unit.

All parameter sets included with each component in a configuration are called “preset parameters.”

One DME64N/24N unit has a number of configurations, and a configuration has a number of preset param-

eters.

User Defined buttons

Assigning parameters to be User Defined Buttons enables you to control the device from the ICP1 and the

DME64N/DME24N.

Refer to the DME Designer Owner’s Manual for details.

Introduction to the DME64N/24N

Glossary for the DME64N/24N

DME64N/DME24N Owner’s Manual

Scene

A combination of all configuration and preset parameters is called a “scene.”

Scenes can be recalled from an ICP1, GPI device, other external controllers, DME64N/DME24N, or com-

puter.

Up to 999 scenes can be stored for each device group.

Scene structure

Scene change

16 x 8

Scene

Scene 1

Scene 2

Scene 999

Component

Configuration

Preset

Parameter

Ex.: Gate

• Attack

• Decay

• Range

• Threshold

• Key in

• Hold

Matrix Mixer

96kHz

88.2kHz

48kHz

44.1kHz

EXT.

CLOCK

MID

MASTER

NETWORK

PEAK

SIGNAL

PEAK

SIGNAL

OUT

SCENE NUMBER

12345 678

96kHz

88.2kHz

48kHz

44.1kHz

EXT.

CLOCK

MID

MASTER

NETWORK

PEAK

SIGNAL

PEAK

SIGNAL

OUT

SCENE NUMBER

12345 678

First Act Dark Change Second Act

Band Set

Play Set

Stage Stage Stage

Play

Set

Band

Set

Band Set

Play Set

Scene 1 Scene Recall Scene 2

Introduction to the DME64N/24N

Signal Types

DME64N/DME24N Owner’s Manual

Signal Types

DME64N/24N audio system signals can be broadly categorized as follows.

1 Audio

The DME64N/24N will be required to send and receive audio signals to and from other DME series units as

well as other audio equipment.

Audio signal transmission and reception will occur primarily via the [INPUT] and [OUTPUT] connectors on

the DME24N.

2 Control signals within a device group

Device group control signals control all DME series devices in the group.

There are two types of device group control signals, as follows:

• Control signals between the computer and the group master DME series unit

• Control signals between the group master DME series unit and the other DME series units

You can use the DME Designer application to control the entire device group, such as sending components

to the devices and setting the parameters as required.

3 Control signals between devices outside the device group

These signals provide communication and control between individual devices.

Included in this category are MIDI messages transferred between [USB] connectors, GPI signals trans-

ferred between [GPI] connectors, and remote head amp control signals handled via the [REMOTE] connec-

tor.

Type of signals handled by the DME64N/24N

Connector Audio Signal Device Control Word Clock

Reference

Page

[USB]

Connector

– • Control signals between computer and

DNE64N/24N

• MIDI messages

–22

[NETWORK]

Connector

– • Control signals between computer and

DNE64N/24N

• Control signals between DME series

unit.

• Control signals with a controller such as

an AMX or Crestron

–23

[MIDI]

Connector

– Control signals (MIDI commands)

between MIDI controller and DME64N/

24N.

–30

[GPI]

Connector

– Control signals between GPI device (GPI

controller, etc.) and DME series unit

–33

[CASCADE]

Connector

(DME64N

only)

32 channels of

input/output.

Control signals from the digital mixer to

the DME64N

Word clock transmission and

reception to and from other

devices.

[WORD

CLOCK]

Connector

– – Word clock transmission and

reception to and from other

devices.

[REMOTE]

Connector

– • Control signals to/from an external

device (such as AD8HR head amplifier)

• Control signals for a digital mixer and

internal head amp

• Control signals with a controller such as

an AMX or Crestron

• MIDI messages

–28

(Audio I/O

Connectors)

(DME24N

only)

8 channels of

input and output.

––26

(I/O Slot) Number of I/O

channels depends

on card.

Serial signal transmission/reception

(depending on function of card).

Word clock transmission and

reception to and from other

devices (depending on function

of card).

Introduction to the DME64N/24N

System Examples

DME64N/DME24N Owner’s Manual

System Examples

Large systems using CobraNet

HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE

ENTERENTERCANCELCANCEL

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

96kHz

88.2kHz

48kHz

44.1kHz

EXT.

CLOCK

MID

MASTER

NETWORK

PEAK

SIGNAL

PEAK

SIGNAL

OUT

SCENE NUMBER

12345 678

96kHz

88.2kHz

48kHz

44.1kHz

EXT.

CLOCK

MID

MASTER

NETWORK

PEAK

SIGNAL

PEAK

SIGNAL

OUT

SCENE NUMBER

12345 678

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

DME8o-C

DME8i-C

DME24N

DME64N

DME24N

MY16-CII

MY16-CII x 4

ICP1

Computer

Network

Switch

Network

Switch

Network

Switch

Network

Switch

Network

Switch

Network

Switch

Network

Switch

Network

Switch

Space BSpace A

Space C

Space D

Analog In

Analog Out

Analog In

Analog Out

Ethernet

CobraNet

Ethernet Network Switch

CobraNet Network Switch

Analog Out

Introduction to the DME64N/24N

About DME Designer

DME64N/DME24N Owner’s Manual

About DME Designer

DME Designer software enables you to integrate, configure, and control the DME series system from a con-

nected computer.

You can build the DME series audio system using graphic blocks in DME Designer that are displayed on

the computer monitor.

The DME series settings, configuration, and parameter data are transferred from the computer to the DME

series unit via the USB or Ethernet connection.

DME series settings, configuration, and parameter data is sent via USB or Ethernet to the connected DME

series unit. After the data is transmitted, you can disconnect the DME series unit from the computer and use

it as an independent processor.

You can also connect it to a computer and control it in realtime from DME Designer.

If multiple DME series units are connected in the network, DME Designer enables you to build a configura-

tion that includes those units.

Please download the DME Designer application, driver, DME setup manual, and DME Designer Owner’s

Manual at the following URL: http://www.yamahaproaudio.com/

Refer to the “Connecting to a Computer” (page 22) for more information on connecting a computer to the

DME64N/24N. For details on how to install DME Designer and the drivers that are required for connection,

refer to the “DME Setup Manual.”

Refer to the DME Designer Owner’s Manual for setup and operation instructions.

The Controls and Connectors

Front Panel

DME64N/DME24N Owner’s Manual

Front Panel

[USB] Connector

A computer can be connected here when it is necessary

to program or control the device. When a USB

connection is to be used, the USB-MIDI driver must be

installed on the computer. Refer to the DME Designer

Installation Guide for installation instructions.

[EXT. CLOCK] Indicator

When a clock signal from an external device is selected,

the indicator will light green. If the clock signal is not

appropriate the indicator will flash red. The indicator will

go out when the internal word clock is selected.

[96kHz] [88.2kHz] [48kHz] [44.1kHz]

Indicator

Normally, the indicator corresponding to the current

word clock frequency will light green. If a problem with

the master clock is detected all of these indicators will

flash red. 2 seconds after a problem is detected with an

external master clock the internal clock will temporarily

be selected. When this happens the indicator

corresponding to the frequency of the internal clock will

light green, and all other indicators will continue to flash

red.

[NETWORK] Indicator

Lights while data communication is occurring via the

[USB], [NETWORK], or [CASCADE] connector. Received

data causes the indicator to light in green, while

transmitted data causes the indicator to light in orange.

If a problem occurs the indicator will light in red.

The Controls and Connectors

HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE

ENTERENTERCANCELCANCEL

HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE

ENTERENTERCANCELCANCEL

DME64N

DME24N

The Controls and Connectors

Front Panel

DME64N/DME24N Owner’s Manual

[MIDI] Indicator

Lights while data communication is occurring via the

[MIDI] connector. Received data causes the indicator to

light green, while transmitted data causes the indicator

to light orange. The indicator will light green when

reception and transmission occur simultaneously. If a

problem occurs the indicator will light red.

[MASTER] Indicator

Lights green when the device is operating as the device

group master (page 9). The indicator will not light if the

device is operating as a device group slave. Refer to

page 45 for device group master setup instructions.

[PEAK] Indicator (DME24N only)

Light red when a signal on the corresponding built-in

analog audio input or output ([IN] and [OUT]

connectors) reaches or exceeds -3 dB.

[SIGNAL] Indicator (DME24N only)

Light green when a signal with a level greater than -40

dB is present at the built-in analog audio inputs and

outputs ([IN] and [OUT] connectors).

[SCENE NUMBER] Indicator

Shows the current scene number.

Display

Displays scene information and device parameters.

[SCENE] Button

Calls the scene recall/store display (page 39). The

scene store display will appear if the button is held for

longer than 2 seconds (page 40). The indicator will light

green while the scene recall or store display is showing.

[HOME] Button

Directly recalls the home (main) display. If pressed while

the main display is showing the [HOME] button steps

through the user-defined parameter display pages (refer

to page 38 in this manual).

[UTILITY] Button

Calls the output level display. If this button is held for

longer than 2 seconds while the main display is showing

the utility display will appear. Switches between the

Utility display pages if pressed while the Utility display is

showing.

[LEVEL] Button

Calls the output level setup display (page 39).

The indicator will light green.

[MUTE] Button

Calls the mute display (page 39). The indicator will light

orange when mute is on. The indicator will light green

when mute is off and the mute display is showing, and

will be off if the mute display is not showing.

Dial

Adjusts the value of selected parameters.

[ E ] [  ] [  ] [ F ] Buttons

Move the display cursor in the corresponding directions.

[CANCEL] Button

Closes the window on the display.

[ENTER] Button

Confirms and enters a value or setting.

[PHONES] Jack

A pair of headphones can be plugged in here.

[PHONES LEVEL] Control

Adjusts the headphone volume. Even when the control is

set to the minimum level, the sound at the headphones is

not completely muted.

[MONITOR] Button

Calls the monitoring point slot selection display (page

40). When the [ENTER] button is pressed to select a slot,

the monitoring point selection display will appear.

The spectrum analyzer display will then appear when the

[ENTER] button is pressed to select a monitoring point.

The indicator will light green while the monitoring slot/

point or spectrum analyzer display is showing.

[POWER] Switch

Turns mains power to the device on and off.

NOTE

The DME64N has no built-in analog audio inputs or

outputs ([IN] and [OUT] connectors).

Even when the power switch is turned off,

electricity is still flowing to the product all the

minimum level. When you are not using the

product for a long time, make sure to unplug

the power cord from the wall AC outlet.

CAUTION

The Controls and Connectors

Rear Panel

DME64N/DME24N Owner’s Manual

Rear Panel

[AC IN] Connector

This is the device’s three-pronged AC power connector.

Connect to the AC mains using the supplied AC power

cord. See “Setup” on page 18 for details.

Even when the power switch is turned off,

electricity is still flowing to the product all the

minimum level. When you are not using the

product for a long time, make sure to unplug the

power cord from the wall AC outlet.

Ground Screw

The supplied AC power cable is a 3-wire type, so if the

AC outlet used is properly earthed the DME64N/24N will

be earthed as well. Hum and interference may by further

reduced in some cases by also connecting the earth

screw to an earth point.

[GPI] Connector

This Euroblock connector provides access to the unit’s

GPI (General Purpose Interface) interface for transfer of

control signals to and from external equipment. The

DME64N provides 16 channels of GPI input and output,

while the DME24N provides 8 channels. Each input

channel has an IN terminal and a +V terminal. Output

channels each have an OUT terminal and a GND

terminal. The open voltage at the +V terminal is 5V, while

the IN terminal detects voltage changes from 0V ~ 5V.

The OUT terminals output either signal “L” or “H” at a

TTL level.

See “GPI Connection ([GPI] Connectors)” on page 33

for connection details.

[MIDI IN] [MIDI OUT] [MIDI THRU]

Connectors

These are standard MIDI connectors that handle

reception and transmission of MIDI data: [MIDI IN]

receives MIDI data, [MIDI OUT] transmits MIDI data, and

[MIDI THRU] re-transmits MIDI data received at the

[MIDI IN] connector. See “MIDI Connection ([MIDI]

Connectors)” on page 30 for connection details.

[WORD CLOCK IN] [WORD CLOCK OUT]

Connectors

These BNC connector receive and transmit word clock

from and to external equipment. See “WORD CLOCK

Connection ([WORD CLOCK] Connectors)” on page 32

for connection details. Word clock settings are available

via the device’s Utility display WCLK page (see page 50

of this document).

DME64N

DME24N

NOTE

Use the supplied AC cord clamp to prevent accidental

disconnection of the AC power.

NOTE

Connect the device to only one ground point.

Connecting the device to more than ground point can

result in ground loops that can cause increased hum and

noise.

CAUTION

The Controls and Connectors

Rear Panel

DME64N/DME24N Owner’s Manual

[NETWORK] Connector

This is a 100Base-TX/10Base-T Ethernet connector for

connection to a computer or other DME series units.

Normally this connector will be connected to a network

switch via an Ethernet cable. When two DME64N/24N

units are to be directly connected a “cross” cable should

be used. See “Ethernet Connection ([NETWORK]

Connector)” on page 23 for connection details.

[REMOTE] Connector

This 9-pin D-SUB connector allows connection to

Yamaha AD824 or AD8HR remote head amplifier or an

RS-232C/RS-422 compatible controller such as those

from AMX or Crestron. You can also connect a Yamaha

PM5D or DM2000 and control the internal head amps of

DME24N. Refer to page 28 for connection details.

[IN] [OUT] Connectors (DME24N only)

These are balanced Euroblock connectors for analog

audio input and output. The analog signal from

microphones or line sources such as CD players can be

input via the IN connectors, while the OUT connectors

can deliver analog output to powered speakers or

recording equipment. 48V phantom power can be

supplied to the IN connectors (page 51). Refer to page

26 for [IN] and [OUT] connection details.

I/O Slots

Optional Yamaha or third-party mini-YGDAI cards can be

plugged in here for system expansion. The DME64N has

four I/O slots, while the DME24N has one.

One expansion card can be plugged into each slot.

Refer to “I/O Card Installation” on page 20 for installation

details.

[CASCADE IN] [CASCADE OUT]

Connectors (DME64N only)

This 68-pin D-SUB connector can be connected to the

CASCADE connector of other devices via a dedicated

cascade cable. The CASCADE connector transmits and

receives control, audio, and word clock signals. Refer to

“Cascade Connection ([Cascade] Connectors” on page

31 for connection details.

NOTE

Use a STP (Shielded Twisted Pair) cable for this

connection to prevent electromagnetic interference.

NOTE

The [IN] and [OUT] connectors each have 24 terminal

pins. Each of the eight inputs and outputs uses three

pins – hot, cold, and ground. Use the supplied 3-pin

Euroblock plugs to connect to the appropriate inputs

and outputs.

Setup

Setup Procedure

DME64N/DME24N Owner’s Manual

Setup Procedure

Follow the steps outlined below to prepare the DME64N/24N for operation.

1. Install any required I/O cards.

Refer to “I/O Card Installation” on page 20 for details.

2. Connect the AC power cord.

Be sure to turn all devices OFF before connecting AC mains power.

Attach the cable clamp to prevent accidental disconnection.

Attaching the cable clamp.

Be sure to properly ground the device to prevent possible electrical shock.

First plug the female-connector end of the AC cord into the [AC IN] socket on the rear panel of the

DME64N/24N, then plug the male plug into an appropriate AC mains outlet. Make sure the AC power to be

used complies with the conditions marked on the top cover of the device.

Use only the AC power cord supplied with the DME64N/24N. If the supplied cord is lost or damaged

and needs to be replaced, contact your Yamaha dealer. The use of an inappropriate replacement

can pose a fire and shock hazard!

The type of AC power cord provided with the DME64N/24N may be different depending on the

country in which it is purchased (a third prong may be provided for grounding purposes). Improper

connection of the grounding conductor can create the risk of electrical shock. Do NOT modify the

plug provided with the DME64N/24N. If the plug will not fit the outlet, have a proper outlet installed

by a qualified electrician. Do not use a plug adapter which defeats the grounding conductor.

3. Install the DME Designer software and necessary drivers on the computer to be used for

device group control.

See the “DME Setup Manual” (PDF file) for details.

Setup

Security Cover Mounting

Security cover mounting screw holes (M3 size) are provided on the front panel of the unit. The spacings are 423mm

width and 96mm (DME64N) / 52mm (DME24N) height. See “Dimensions” on page 65 for details. A security cover

made by the customer or contractor can be attached to the front panel via these mounting holes to prevent

accidental operation. Yamaha cannot supply a security cover.

When mounting a cover make sure that the screws used do not go deeper than 15 millimeters into the front panel.

Also, to ensure that the cover does not come in contact with the panel controls, leave a space of about 20 millimeters

between the front panel and the cover.

CAUTION

Setup

Setup Procedure

DME64N/DME24N Owner’s Manual

4. Connect devices.

• Network connection

Ethernet connection (page 23)

USB connection (page 22)

• Analog connection (page 26)

• External device connection

Remote connection (page 28)

MIDI connection(page 30)

CASCADE connection(page 31)

WORD CLOCK connection(page 32)

GPI connection (page 33)

5. Turn power to the computer, DME64N/24N, and related devices on. Press the DME64N/24N

[POWER] switch to turn it on.

To prevent the initial power-on surge from generating a large noise spike or damaging your speaker

system, turn devices on in the following order: audio sources, mixer and/or recorders, and finally

power amplifiers. Reverse this order when turning power off.

No information will appear on the display the first time the device is turned on. The appropriate scene and

other data must first be transferred to the device from the DME Designer.

Refer to the “DME Setup Manual” (PDF file) for details.

Once the appropriate data has been transferred to the device, the current number and name will appear

on the display:

If any scene data has been stored in the DME64N/24N, the current scene and its name will be displayed.

6. Set up the DME64N/24N operation parameters.

See the “Utility Display” section on page 43 for details.

7. Launch the DME Designer application, create configuration and transfer.

DME Designer setup, operation, and data transfer instructions can be found in the DME Designer Manual.

This completes preparation of the DME64N/24N system.

NOTE

The “NET” page settings must be set up as required before using the unit for the first time.

CAUTION

Setup

I/O Card Installation

DME64N/DME24N Owner’s Manual

I/O Card Installation

The DME64N has four I/O card slots, and the DME24N has one I/O card slot. The number of audio input channels

available on the DME64N/24N can be increased by plugging the appropriate mini-YGDAI I/O card(s) into the available

card slot(s).

Compatible I/O Cards

As of June, 2010, Yamaha mini-YGDAI cards that can be used with the DME64N/24N are as follows:

The input/output numbers above apply to 44.1/48kHz operation.

(*)

In order to use three or four MY16-C cards, firmware V1.10 or later will be required.

If the serial number written on the upper surface of your DME64N is shown below, a hardware upgrade is needed.

KK, KL, KM, KN, KO, KP, KX, KY are the third and fourth digits of the serial number.

A fee is charged for the hardware upgrade.

For details, contact Yamaha customer support using the contact information located at the end of the “DME64N/24N Owner’s

Manual.”

For the latest information on what cards can be used with the DME64N/24N, visit the Yamaha Pro Audio

website at: http://www.yamahaproaudio.com/

Card Name Function Input Output

No. of Available Cards

DME64N DME24N

MY8-ATADAT 8841

MY8-TDTDIF-1 8841

MY8-AEAES/EBU 8841

MY4-AD ANALOG IN 4 – 4 1

MY8-AD ANALOG IN 8 – 4 1

MY4-DA ANALOG OUT – 4 4 1

MY8-AD24 ANALOG IN 8 – 4 1

MY8-AD96 ANALOG IN 8 – 4 1

MY8-DA96 ANALOG OUT – 8 4 1

MY8-ADDA96ANALOG IN/OUT8841

MY8-AE96SAES/EBU 8841

MY8-AE96AES/EBU 8841

MY8-AEBAES/EBU 8841

MY16-AT ADAT 16 16 4 1

MY16-AE AES/EBU 16 16 4 1

MY16-TD TDIF-1 16 16 4 1

MY16-C CobraNet 16 16 4(*) 1

MY16-CII CobraNet 16 16 4 1

MY16-ES64 EtherSound 16 16 1 1

MY16-MD64 MADI 16 16 4 1

MY16-EX Expansion 16 16 3 1

MY8-SDI-D HD-SDI 8 – 4 1

Setup

I/O Card Installation

DME64N/DME24N Owner’s Manual

I/O Card Installation Procedure

1. Make sure that the DME64N/24N power is OFF.

If the power is on, turn it off.

2. Loosen the two card slot screws and remove the slot cover, as shown in the diagram.

3. Slide the I/O card into the slots in the guide rails, as shown in the diagram, and push the

card into the slot.

Be sure to push the card all the way back into the slot so that the card contacts make proper contact with

the slot connector.

4. Secure the card with the attached screws.

Be sure to tighten the screws securely. If the screws are left loose proper contact may be lost and

malfunction of damage may result.

NOTE

The slot cover and screws will need to be re-attached if the I/O card is later removed from the slot, so keep

them in a safe place.

Guide Rail

CAUTION

Connecting to a Computer

USB Connection

DME64N/DME24N Owner’s Manual

USB Connection

USB connections can be used in the following two ways:

(1) Control the DME64N/24N from DME Designer.

(2) Connect to any individual DME64N/24N and control that DME64N/24N unit by transmitting MIDI com-

mands from a MIDI sequencer or similar software.

Be sure to follow the procedure below when you make a USB connection with a computer. Otherwise, the

computer and/or DME64N/24N may freeze, resulting in damages or loss of data. If the computer or

DME64N/24N freezes, turn the power to the DME64N/24N off and then on, then restart the computer.

• Before you connect the DME64N/24N to the computer via USB, cancel the computer’s energy saving

mode (such as Suspend, Sleep, or Stand-by mode).

• Before turning on the power to the DME64N/24N, first connect its [USB] connector to the computer’s

USB port.

• Before turning the power to the unit on or off, and before connecting or disconnecting the USB

cable, take the following actions:

- Quit all open applications.

- Make sure that the DME64N/24N is NOT transferring any data.

• Be sure to wait six seconds or more between turning the power to the unit on and then off (or off and

then on), or between connecting and disconnecting (or vice versa) the USB cable.

Connecting to a Computer

NOTE

• Refer to the “DME Setup Manual” (PDF file) for details on installing USB-MIDI Driver and DME Designer.

• Make sure that the USB-MIDI Driver’s THRU setting is “OFF.”

NOTE

• The computer on which DME Designer is running can be connected to either the group master or a slave DME series

unit.

• The correspondence between the MIDI commands to be received/transmitted and the scene parameters can be set up

using DME Designer.

• The USB port being used by DME Designer is not available for use by a MIDI sequencer or other application.

HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE

ENTERENTERCANCELCANCEL

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

Device Group

DME Satellite

Computer

(Running DME Designer.)

Computer

(Running MIDI

Sequencer or

similar application.)

Ethernet Cable

Network Switch

Ethernet Cable

DME Satellite

Ethernet Cable

DME64N/24N

USB Cable

CAUTION

Connecting to a Computer

Ethernet Connection ([NETWORK] Connector)

DME64N/DME24N Owner’s Manual

Ethernet Connection ([NETWORK] Connector)

To control the DME64N/24N from the computer via Ethernet, use an Ethernet cable to connect the [NET-

WORK] connector on the rear panel of the DME64N/24N to the computer, then install DME-N Network Driv-

er.

Two DME series units directly connected via Ethernet

You can connect devices in the same device group directly to each other using Ethernet cables, without

connecting them to a network switch.

A cross cable or straight cable can be used since the DME series supports Auto MDI/MDI-X. In this case,

set Link Mode on both units to the same setting. Devices in different subnet (different network address)

groups can be connected via a router or layer-3 compliant network switch.

NOTE

• Refer to the “DME Setup Manual” (PDF file) for details on installing DME-N Network Driver.

• Appropriate IP addresses must first be assigned to all devices connected to an Ethernet network.

HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE

ENTERENTERCANCELCANCEL

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

DME64N/24N

DME Satellite

Ethernet Cable

USB Cable

Connecting to a Computer

Ethernet Connection ([NETWORK] Connector)

DME64N/DME24N Owner’s Manual

Control from a computer in the same subnet group

Control from a computer with a different subnet

NOTE

• The IP addresses in the diagram are examples.

• Use a network switch that is compatible with 100Base-TX/10Base-T network speeds.

The maximum length of a cable between a network switch and the DME series is 100 meters. Due to the quality of cables

and network switch performance, however, proper operation at the maximum length cannot be guaranteed in some

cases.

Use a STP (Shielded Twisted Pair) cable to prevent electromagnetic interference.

• If you are using multiple DME series units, set Link Mode on each unit to the same setting. Yamaha recommends that you

select 100Base-TX for the Link Mode setting.

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE

ENTERENTERCANCELCANCEL

Device Group

Group Master

DME Satellite (IP address: 192.168.0.7)

Ethernet Cable

Network Switch

Ethernet Cable

Computer

(IP address:

192.168.0.100)

Ethernet Cable

DME Satellite

(IP address: 192.168.0.3)

(Master ID: 7)

DME64N/24N

(IP address: 192.168.0.250)

(Master ID: 7)

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE

ENTERENTERCANCELCANCEL

Device Group

Group Master

DME Satellite (IP address: 192.168.0.5)

Ethernet Cable

Ethernet

Cable

Ethernet Cable

Network Switch

Router or

Layer-3

Compliant

Network

Switch

Computer

Port settings

Destination network address: 192.168.0.0

Subnet mask: 255.255.255.0

Gateway: 192.168.0.254

DME Satellite

(IP address: 192.168.0.3)

(Master ID: 5)

DME64N/24N

(IP address: 192.168.0.12)

(Master ID: 5)

Connecting to a Computer

Ethernet Connection ([NETWORK] Connector)

DME64N/DME24N Owner’s Manual

Connecting multiple device groups

HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE

ENTERENTERCANCELCANCEL

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE

ENTERENTERCANCELCANCEL

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

Device Group 1 Device Group 2

Group Master

DME Satellite

(IP address: 192.168.0.2)

Group Master

DME Satellite

(IP address: 192.168.0.3)

Ethernet Cable Ethernet Cable

Ethernet Cable

DME64N/24N

(IP address: 192.168.0.100)

(Master ID: 2)

DME Satellite

(IP address: 192.168.0.40)

(Master ID: 2)

DME Satellite

(IP address: 192.168.0.10)

(Master ID: 3)

DME64N/24N

(IP address: 192.168.0.200)

(Master ID: 3)

Network Switch

Computer

(IP address: 192.168.0.1)

Network Switch

Ethernet CableEthernet Cable

Ethernet Cable

Audio I/O Connection

Analog Audio Connection ([IN] and [OUT] Connectors)

DME64N/DME24N Owner’s Manual

Analog Audio Connection ([IN] and [OUT] Connectors) (DME24N only)

The DME24N includes [IN] and [OUT] connectors for 8 channels of analog audio input and output. Wire

the supplied Euroblock plugs as shown below. Head amplifier gain and phantom power settings can be

made via the Utility display HA page described on page 52 of this manual, or via the DME Designer

application.

Euroblock Connection

Please be sure to use the supplied Euroblock plugs. If you lose them, contact your nearest Yamaha dealer.

1. Loosen terminal screws.

2. Insert cables.

Audio I/O Connection

Cable preparation

• To prepare the cable for attachment to a Euroblock connector, strip the wire as shown

in the illustration, and use stranded wire to make connections. With a Euroblock

connection, the stranded wire may be prone to breakage because of metal fatigue

due to the weight of the cable or due to vibration. When rack-mounting your

equipment, use a lacing bar when possible to bundle and fasten the cables.

• If cables will be frequently connected and disconnected, as in the case of a portable

installation, we recommend that you use ferrules with insulation sleeves. Use a

ferrule whose conductor portion has an external diameter of 1.6 mm or less, and a

length of approximately 7 mm (such as the AI0,5-6WH made by the Phoenix Contact

corporation).

If you use stranded wire, do not tin (plate with solder) the exposed end.

NOTE

A slotted screwdriver with a blade width of about 3 millimeters is

recommended.

approx.

7 mm

approx.

7 mm

1.6 mm

or less

CAUTION

Loosen.

Euroblock Plug

Slotted Screwdriver

Ter m i n al S crew

3 mm

Audio I/O Connection

I/O Slots

DME64N/DME24N Owner’s Manual

3. Securely tighten terminal screws.

Pull the cables (not too strongly) to confirm that they are securely connected.

4. Plug the Euroblock plug into the panel connector.

I/O Slots

The DME64N has four I/O card slots, and the DME24N has one I/O card slot. The number of audio input

channels available on the DME64N/24N can be increased by plugging the appropriate mini-YGDAI I/O

card(s) into the available card slot(s). Some types of cards also provide control and/or word clock

transmission and reception functionality.

Refer to “Compatible I/O cards” (page 20) for details on the cards that can be used.

For details on how to install cards, refer to “I/O card Installation Procedure” (page 21).

Connecting to an External Device

Remote Connection ([REMOTE] Connector)

DME64N/DME24N Owner’s Manual

Remote Connection ([REMOTE] Connector)

The [REMOTE] connector of the DME64N/24N can be connected to remotely-controllable Yamaha AD8HR

or AD824 head amplifiers (pre-amps), digital mixers, or RS-232C compatible controllers (such as those from

AMX or Crestron). The [REMOTE] connector also transmits and receives MIDI messages.

Controlling external head amplifiers from the DME64N/24N

You can remotely control the AD8HR or AD824 head amplifier settings from DME Designer. Up to eight

AD8HR/AD824 head amplifiers can be connected.

When connecting to a combination of AD8HR and AD824 head amplifiers, be sure to place the AD8HR units

closest to the DME64N/24N in the chain, otherwise the AD8HR or AD824 unit(s) may not be properly rec-

ognized by the DME64N/24N. For details about the settings, refer to the “Ext HA Ctrl” in “Remote page” on

page 49.

Connecting to an External Device

NOTE

Only control signals are transmitted and received via the REMOTE connection. Audio connections must be

made separately.

D-SUB 9-pin Cable (Interlink Crossover)

REMOTE

Set to Remote

(422)

HA REMOTE 2HA REMOTE 1 HA REMOTE 1 HA REMOTE 2

AD8HR AD8HR

AD824 AD824 AD824

DME64N/24N

COM PC/RS-422 COM RS-422 COM PC/RS-422 COM RS-422 COM PC/RS-422

Connecting to an External Device

Remote Connection ([REMOTE] Connector)

DME64N/24N Owner’s Manual

Controlling a DME24N’s internal head amps from a digital mixer

The internal head amp settings of a DME24N can be remotely controlled from a digital mixer such as the

Yamaha PM5D or DM2000.

Connect the digital mixer to the DME series’ [REMOTE] connector, and use an Ethernet cable to make con-

nections between the [NETWORK] connectors of the DME series. From the digital mixer, DME series units

can be controlled as an AD8HR.

The gain and the phantom power (+48V) can be controlled. For details about the settings, refer to the “Int

HA Ctrl” in “Remote page” on page 49.

Controlling the DME64N/24N from an external device

You can remotely control the DME64N/24N from a connected RS-232C or RS-422 compatible controller,

such as those from AMX or Crestron.

When connecting a remote controller via RS-232C or RS-422, be sure to set the “Utility” display “Remote

page” (see manual page 45) “Rmt Ctrl” parameter to match the controller being connected. Also, do

change this setting while the unit is connected. Doing so can damage the unit.

NOTE

Only one mixer can be connected within each device group.

The digital mixer can be connected to any DME series unit, whether it is the group master or a slave unit.

The ID number of the DME series unit being remotely controlled is specified from DME Designer.

For details on making this setting, refer to the “DME Designer Owner’s Manual.”

If the connection between DME series units is broken, it will no longer be possible to communicate with DME

units of an ID number that follows the disconnected DME.

The variable range of GAIN differs between the AD8HR and the DME24N. You cannot use the mixer to

specify a value that exceeds the variable range of the DME24N.

NOTE

Refer to “DME Remote Control Protocol Specifications” on the Yamaha web site for more information on

communication protocols used to control the DME64N/24N from an external device (such as those from

AMX or Crestron).

http://www.yamahaproaudio.com/

96kHz

88.2kHz

48kHz

44.1kHz

EXT.

CLOCK

MID

MASTER

NETWORK

PEAK

SIGNAL

PEAK

SIGNAL

OUT

SCENE NUMBER

12345 678

96kHz

88.2kHz

48kHz

44.1kHz

EXT.

CLOCK

MID

MASTER

NETWORK

PEAK

SIGNAL

PEAK

SIGNAL

OUT

SCENE NUMBER

12345 678

DME64N/24N

REMOTE REMOTE

Ethernet Cable

Network

Switch

Digital Mixer

D-SUB 9-pin Cable

DME64N/24N

Connecting to an External Device

Network Connection ([NETWORK] Connectors)

DME64N/DME24N Owner’s Manual

Network Connection ([NETWORK] Connectors)

You can connect a controller such as the AMX or Crestron to DME64N/24N via Ethernet, and remotely

control multiple DME64N/24N units. For details about the settings, refer to the "Rmt Ctrl" in "Remote page"

on page 48.

• The port used for remote control is specified from DME Designer. For details on making this setting, refer

to the “DME Designer Owner’s Manual.”

• Refer to “DME Remote Control Protocol Specifications” on the Yamaha web site for more information on

communication protocols used to control the DME64N/24N from an external device (such as those from

AMX or Crestron).

http://www.yamahaproaudio.com/

MIDI Connection ([MIDI] Connectors)

In this case connection is made to the rear-panel [MIDI] connectors. MIDI commands are sent to the

DME64N/24N from a MIDI device. Refer to “MIDI Page” on page 49 for MIDI setup details.

By connecting the [MIDI OUT] terminal of a digital mixer (such as the DM2000) to the [MIDI OUT] of the

DME64N/24N and making the proper settings on the mixer and the DME64N/24N, you can change scenes

by sending program change messages from the mixer.

If the [MIDI OUT] connector of the DME64N/24N is connected to the [MIDI IN] connector of an SPX2000 or

similar digital effect unit, and if the DME64N/24N and SPX2000 are set up appropriately, DME64N/24N

program change operations will case the corresponding effect to be recalled on the effect unit.

NOTE

The DME Designer can be used to set up the system so that scene recall operations and user parameter

control can be carried out from connected MIDI devices. Refer to the DME Designer manual for details.

MIDI OUT MIDI IN

DME64N/24N

MIDI Cable

DM2000 Digital Mixer or Other Controller

MIDI OUT MIDI IN

DME64N/24N

MIDI Cable

SPX2000 or Other Digital Effect Unit

Connecting to an External Device

Cascade Connection ([Cascade] Connectors) (DME64N only)

DME64N/DME24N Owner’s Manual

Cascade Connection ([Cascade] Connectors) (DME64N only)

The rear-panel [CASCADE] connector can be connected to the [CASCADE] connector on another

DME64N/24N or other compatible device via a dedicated cascade cable for bidirectional transfer of

control, audio, and word clock signals. The communication direction automatically switches to

unidirectional when connecting to a mixer such as the PM5D, or bidirectional when connecting to another

DME64N/24N unit.

Up to eight DME64N units can be cascade connected.

In the unidirectional mode the audio signal flow is from the [CASCADE OUT] connector to the [CASCADE

IN] connector. For bidirectional communication the data flows in both directions within a single cable, and

input on the same channel from other DME64N units is summed (bus sharing). The total number of audio

channels that can be connected to a mixer or DME64N/24N unit is 32.

Word clock is continuously output from both the [CASCADE IN] and [CASCADE OUT] connectors, and is

received by the corresponding [CASCADE IN] or [CASCADE OUT] connector on the connected device.

In all cases the [CASCADE OUT] of one device must be connected to the [CASCADE IN] connector of the

other. Do not connect [CASCADE IN] to [CASCADE IN], or [CASCADE OUT] to [CASCADE OUT].

Cascade Connection Example

NOTE

Maximum length by the optional dedicated Cascade cables

Unidirectional Cascade connection: 200m (44.1/48kHz), 100m (88.2/96kHz)

Bidirectional Cascade connection: 100m (44.1/48kHz), 30m (88.2/96kHz)

NOTE

Never create a full cascade loop using only DME64N units!

NOTE

It is also possible to remotely control DME series units from the PM5D via a CASCADE connection. In such

cases assign the nearest DME64N unit to the PM5D as the device group master. When using a DME64N/24N

together with the DME Satellite, you must assign the DME Satellite as the master.

Another method of remotely controlling a DME series from a PM5D is via CobraNet connections to MY16-C or

MY16-CII cards.

All DME series units to be controlled from the PM5D must be in the same device group, and the host address

of the device group master must be set to “2.” However, if the PM5D is version 2.20 or higher and the DME

Satellite is version 3.07 or higher, you can set the parameter to any number.

For information on the PM5D DME CONTROL function refer to the PM5D/PM5D-RH Owner’s Manual or to the

“Cascade Setup Guide” available at the Yamaha website.

http://www.yamahaproaudio.com/

DME64NDME64N

OUT

PM5D

DME64N DME64N

IN OUT

OUT

IN OUT

Unidirectional Cascade Connection

Bidirectional Cascade Connection

68-pin Half-pitch D-SUB Cable

68-pin Half-pitch

D-SUB Cable

68-pin Half-pitch

D-SUB Cable

Connecting to an External Device

WORD CLOCK Connection ([WORD CLOCK] Connectors)

DME64N/DME24N Owner’s Manual

WORD CLOCK Connection ([WORD CLOCK] Connectors)

Word clock signals are transferred to and from external devices via the [WORD CLOCK IN] and [WORD

CLOCK OUT] connectors. The [WORD CLOCK OUT] connector can be used to supply the DME64N/24N

word clock to external equipment. Word clock is continuously output by the DME64N/24N during normal

operation. The word clock signal from an external device can be received via the [WORD CLOCK IN]

connector. Refer to the Utility display WCLK page described on page 50 of this manual for details.

To distribute the word clock signal from one device to multiple slave devices, either a word clock

distribution box or daisy-chained connection can be used.

Distribution Box Connection

Daisy Chain Connection

NOTE

Word clock can also be received and transmitted via a mini-YGDAI card installed in an I/O slot, or the

[CASCADE IN] and [CASCADE OUT] connectors. It is necessary to specify whether the DME64N/24N will use

the internal word clock or an external word clock for synchronization.

NOTE

A device transmitting the word clock signal that will be used by other devices for synchronization is the “word

clock master,” while devices received the word clock are “word clock slaves.”

NOTE

This method is not recommended for large systems.

WC OUT

(BNC)

WC IN

(BNC)

DME64N/24N

Word Clock

Master

Word Clock Slave

WC OUT (BNC)

WC IN (BNC) WC IN (BNC) WC IN (BNC) WC IN (BNC)

DME64N/24N DME64N/24N DME64N/24N DME64N/24N

Word Clock

Master

Word Clock

Distribution Box

Word Clock Slave Word Clock Slave

WC OUT

(BNC)

WC OUT

(BNC)

WC OUT (BNC)

WC IN

(BNC)

WC IN

(BNC)

WC IN

(BNC)

DME64N/24N DME64N/24N DME64N/24N

Word Clock

Master

Word Clock Slave

Connecting to an External Device

GPI Connection ([GPI] Connectors)

DME64N/DME24N Owner’s Manual

GPI Connection ([GPI] Connectors)

GPI (General Purpose Interface) device (GPI controller, etc.) can be connected to the rear-panel [GPI]

connectors. Using GPI a variety of control signals can be transferred between the DME64N/24N and

external controllers or other devices. The optional CP4SW, CP4SF, and CP1SF control panels are also

connected via GPI.

The DME64N provides 16 channels of GPI input and output, and the DME24N provides 8 channels. Each

channel has an IN terminal, a +V terminal, an OUT terminal and a GND terminal. The +V terminals have an

open-terminal voltage of 5 volts. The IN terminals can detect a full range of input voltages from 0V through

5V, while the OUT terminals output either signal “L” or “H” at a TTL level.

The parameters for each GPI input and output are assigned via the DME Designer application.

Euroblock connectors are used for all GPI input and output connections. Euroblock connection methods

are described in “Euroblock Connection” on page 26 in this manual.

NOTE

For more information on the CP4SW, CP4SF, and CP1SF control panels refer to “CP4SW, CP4SF, and CP1SF”

in the Appendix of this manual (page 51).

NOTE

The DME Designer can be used to set up the system so that scene recall operations and user parameter

control can be carried out from connected GPI control devices. Refer to the DME Designer manual for details.

NOTE

GPI connector calibration procedure is described on page 51 of this manual, in the Utility display GPI page.

IN +V

IN +V GND

OUT GND

Example: Controlling the

DME64N/24N from a switch.

GPI Connection

Example: Controlling the

DME64N/24N via a 10k ohm

linear taper potentiometer.

GPI Connection

Continuous

potentiometer

GPI Connection

Example: Lighting external

LED indicators from the

DME64N/24N.

Max. 16mA

Make sure that the current

between the OUT and GND [GPI]

connectors is less than 16mA.

CAUTION

Panel Operation and Displays

Basic Operation

DME64N/DME24N Owner’s Manual

Basic Operation

By pressing the panel buttons it is possible to select the DME64N/24N Main display, Utility display, and Parameter Edit

displays that allow individual settings to be edited and changed. refer to the pages listed below for more detailed

information about each display.

[HOME] button  Main Display (page 35)

The Main display can be directly recalled from any display other than the Main display by pressing the

[HOME] button. The Main display shows the current scene information.

[HOME] button  User Defined Button Page Selection (page 38)

Pressing the [HOME] button while the Main display is shown sequentially selects the four User Defined

Button pages.

[MUTE] button  Mute Display (page 39)

[LEVEL] button

 Output Level Display (page 39)

[SCENE] button

 Scene Recall Display (page 39)/Scene Store Display (page 40)

These buttons can be pressed from the Main or Utility displays to directly call the related parameter edit

displays.

[MONITOR] button  Monitor Point Selection Display (page 40)

This function is useful for level monitoring. When the button is pressed the monitor point selection display

will appear, and the spectrum analyzer display will appear when a selection has been made.

[UTILITY] button  Utility Display (page 43)

The Utility display appears when the [UTILITY] button is pressed for longer than two seconds while the

Main display is showing.

The Utility display includes a number of pages that can be selected in sequence by repeatedly pressing

the [UTILITY] button.

Panel Operation and Displays

HOMEHOME

Main display

Switches the pages of the User Defined Button

Panel Operation and Displays

Main Display

DME64N/DME24N Owner’s Manual

Main Display

The Main display will appear in a few seconds after the

power is turned on. The Main display shows information

about the current scene.

Up to 24 parameters can be accessed from the

DME64N/24N or ICP1 control panel for each scene. Six

parameters are shown on the Main display at a time.

Scene Information

The current scene number and name. Scene names can

be entered by using the DME Designer application.

A maximum of 12 one-byte (Roman) characters can be

displayed in a scene name. When “two-byte” characters

are to be used for languages such as Japanese, the total

number of displayable characters is reduced

accordingly.

When the power is turned on the last scene selected

before the power was turned off is automatically

recalled.

Edit Indicator

If a parameter is changed after recalling a scene, a dot

will appear in the scene number indicator, and “EDIT”

will appear in the display.

User Defined Button Names

Displays the User Defined Button. The buttons are

specified by using the DME Designer application.

“No Assign” settings in DME Designer are displayed as

dotted lines. When [Parameter Value Edit] is selected the

display will be a solid line. When [Direct Parameter

Value], [Scene Change], [GPI Out], or [Play Wav File] are

selected, the display will be inverted.

A maximum of 24 buttons can be made available for

user control, but only six buttons can be shown in any

one display page. Press the [HOME] button to switch to

other available button pages. A maximum of 8 one-byte

(Roman) characters can be displayed in a button name.

When “two-byte” characters are to be used for

languages such as Japanese, the total number of

displayable characters is reduced accordingly.

Buttons are selected for editing by using the cursor

buttons – [ E ] [  ] [  ] [ F ] – to select the button,

and then pressing [ENTER].

Page Scroll Bar

The scroll bar provides an indication of which parameter

page is currently being displayed. 4 pages are

available, and the scroll bar moves one position to the

right each time the [HOME] button is pressed and a new

page of parameters is selected, and then back to the

leftmost position after the rightmost position has been

reached.

Mute Indicator

Shows the current mute ON/OFF status.

: Mute ON

: Mute OFF

Output Level Indicator

Displays the current output level in 10 increments.

The longer the “bar,” the higher the output level.

Panel Lock Icon

This icon appears when the panel lock function is turned

ON.

: Panel Lock ON (Panel controls locked)

NOTE

Nothing will appear on the display if no scene data is

stored in the DME64N/24N scene memory (this is the

case when the unit is initially shipped, for example).

NOTE

User Defined Button settings are common to the device

group.

NOTE

Scroll bar operation is independent for each DME64N/

DME24N unit, and is not linked within a device group.

Panel Operation and Displays

Parameter Edit Displays

DME64N/DME24N Owner’s Manual

Parameter Edit Displays

Parameter Edit displays will appear when the [SCENE],

[MUTE], [MONITOR] or other button is pressed to allow

scene changes, level adjustment, and other settings to

be edited as required. Parameter Edit displays are also

used to edit utility parameters.

In most cases the desired parameter edit page can be

accessed by selecting the item you want to edit in the

appropriate display by using the cursor [ E ], [  ], [ 

], and [ F ] buttons, and then pressing the [ENTER]

button.

There are basically three types of parameters that can

be accessed via a Parameter Edit display:

• Numeric values

•Lists

• ON/OFF switches

Numeric Parameters

Numeric parameters can be edited in a number of ways,

and depending on the parameter a fader, knob, or

minimum and maximum values may appear to the left of

the numeric value.

A Numeric Value with a fader

A Numeric Value with a Knob

Name of parameter selected for editing

Fader

Knob

Minimum and maximum values

Current value

Panel Lock

The panel controls can be “locked” to prevent

accidental mis-operation.

To activate the panel lock function simultaneously

press and hold the [HOME] and [ENTER] buttons for

longer than 2 seconds.

The panel lock icon will appear on the Main display

when the panel is locked.

Panel Lock can be disengaged by pressing the

[CANCEL] button for longer than 2 seconds.

NOTE

The panel lock function can be set up to lock just the

panel buttons (“Key Only”), or the panel buttons and GPI

control (“Key+GPI”). You can also select whether or not

the panel lock function is automatically engaged when

the unit is initially turned on. This selection can be made

via the Utility display “Lock” page (refer to the page 47).

Panel lock icon

Panel Operation and Displays

Parameter Edit Displays

DME64N/DME24N Owner’s Manual

Some Parameter Edit displays have just one numeric

parameter, while other may have two or more.

1. Numeric values can be changed by rotating

the dial. Dial rotation produces an

immediate, corresponding change in the

selected value.

2. Press the [ENTER] button to close the

Parameter Edit display after the value(s)

have been edited as required.

1. Use the cursor buttons – [ E ] [  ] [  ] [ F ]

– to select the value to be edited.

2. Rotate the dial to edit the value as required.

3. Repeat step 1 to select the next value to be

edited, use the dial to edit as required, and

repeat until all values have been edited as

required.

4. When all values have been edited, press the

[ENTER] button. A confirmation window will

appear: press [ENTER] one more time to

confirm the edits and close the window.

Parameter Edit Display with One Numeric Parameter

Parameter Edit Display with Multiple Numeric

Parameters

NOTE

You can close the window without changing any values

by pressing the [CANCEL] button rather than the

[ENTER] button.

ENTERENTER

Panel Operation and Displays

Parameter Edit Displays

DME64N/DME24N Owner’s Manual

List Parameters

List parameters allow you to make one selection from a

list of possibilities.

Rotate the dial to scroll up or down the list. In some

cases the centermost item on the display will be always

highlighted as the list is scrolled, and in others the same

item will remain highlight as the list is scrolled up or

down.

1. Use the dial to scroll up or down the list.

As you scroll the centermost item on the display will

be highlighted.

2. Press the [ENTER] button to select the

highlighted item and close the window.

1. Use the dial to scroll up or down the list.

As you scroll the highlighted selection will remain

highlighted, and will scroll up or down with the list.

2. Press the [ENTER] button to highlight the

centermost item on the display.

3. Press the [ENTER] button to select the

highlighted item and close the window.

ON/OFF Parameters

Parameters that are either ON or OFF are edited via this

type of display (e.g., Mute Parameter Edit display in

“Mute Switching” on page 39).

1. Rotate the dial clockwise to select ON, or

counterclockwise to select OFF.

2. Press enter to confirm the selection and

close the window.

Parameter Edit displays will also appear when the

[SCENE], [MUTE], [MONITOR] or other button is

pressed.

These allow scene changes, level adjustment, and other

settings to be edited as required.

Editing User Defined Button

1. If the Main display is not showing, press the

[HOME] button to recall it.

2. Press the [HOME] button until the page

containing the parameter to be edited

appears.

3. Use the [ E ] [  ] [  ] [ F ] buttons select

the parameter to be edited.

4. Press the [ENTER] button.

The Parameter Edit display for the selected User

Defined Button will appear.

5. Edit the User Defined Button as required.

Refer to “Parameter Edit Displays” on page 36 for

editing procedures.

List Parameter with Center Item Always Highlighted

List Parameter with Scrolling Highlight

NOTE

In some cases a confirmation dialog will appear when

the [ENTER] button is pressed. If this occurs press the

[ENTER] button a second time to continue.

NOTE

User Defined Button can be of all three types: numeric,

list, and ON/OFF.

NOTE

When editing from an ICP1 control panel, the [F1] ~ [F6]

buttons are used for button selection.

NOTE

Any changed User Defined Button values will be lost if

the power is turned off or if scenes are changed.

However, if the Last.Mem.Resume setting is ON, the

setting will be preserved even when the power is turned

off. To preserve the changed values, store the scene

data.

Panel Operation and Displays

Parameter Edit Displays

DME64N/DME24N Owner’s Manual

Mute Switching

Turns the DME64N/24N output mute function ON or OFF.

1. Press the [MUTE] button.

The Mute Parameter Edit display will appear.

2. Select Mute ON or OFF.

The mute function is turned on or off as described

in “ON/OFF Parameters” on page 38.

Output Level Control

Adjust the output level of the DME64N/24N.

1. Press the [LEVEL] button.

The “Output Level” Parameter Edit display will

appear.

2. Adjust the numeric output level parameter

as required.

The Output Level parameter is adjusted as

described in “Numeric Parameters” on page 36.

The graphic fader provides a visual indication of the

current output level setting.

Scene Recall

This procedure recalls a new scene (refer to page 10).

1. Press the [SCENE] button.

The Scene Recall display will appear.

2. Select a new scene.

Scenes are selected as described in the “List

Parameters” section on page 38.

3. Press the [ENTER] button.

A confirmation window will appear.

4. Press the [ENTER] button again.

The new scene will be selected.

Don’t turn the power off during a scene recall

operation. Doing so can cause corruption of

the current scene data.

NOTE

To access this function from the ICP1 control panel, hold

the [F6] button for longer than 2 seconds.

NOTE

All outputs in the device group, including the [PHONES]

jack, are muted.

NOTE

Output level settings apply individually to each DME64N/

24N unit. There is no overall device group setting.

This function cannot be accessed from the ICP1 control

panel.

NOTE

The same procedure is used for scene recall from an ICP1

control panel.

CAUTION

Panel Operation and Displays

Parameter Edit Displays

DME64N/DME24N Owner’s Manual

Scene Store

Stores the current scene data for later recall.

1. Press the [SCENE] button for longer than 2

seconds.

A confirmation window will appear on the display.

2. Press the [ENTER] button.

This stores the scene data in the current scene

memory.

Monitoring

The monitor functions allow you to monitor the audio

signal at the inputs or outputs of I/O slots, points

between components, and other critical monitoring

points.

1. Press the [MONITOR] button.

The slots available for monitoring will be shown in

the parameter list.

2. Select the desired monitor source from the

list.

List selections are made as described in the “List

Parameters” section on page 38.

The following five position types can be selected:

1 Slot input/output terminal

2 CASCADE input/output terminal (DME64N only)

3 IN terminal (DME24N only)

4 OUT terminal (DME24N only)

5 User Defined

By connecting 1 through 4 in DME Designer, you

will be able to select the input/output terminal.

You will be able to select 5 by editing the Monitoring

Point List in DME Designer.

NOTE

Scenes can also be changed from a computer or GPI/

MIDI controller connected to the device.

The DME Designer application is used to make scene

changes from a computer. If a GPI/MIDI controller is to

be used for changes it must be initially set up for scene

change control by using the DME Designer.

NOTE

If head amplifier parameters are included in the recalled

scene data, the head amplifier settings will be changed

accordingly.

NOTE

This function can be accessed in the same way from the

ICP1.

NOTE

Press the [CANCEL] button if you want to abort the

scene store operation.

NOTE

If head amplifier settings are included in the scene the

Utility display HA page settings are also stored. If head

amplifier settings are not included in the scene, the HA

page settings are stored as head amplifier startup

settings.

NOTE

Any parameter values changed by GPI/MIDI controllers

will be lost if the power is turned off or if scenes are

changed. To preserve the changed values, store the

scene data.

NOTE

User-defined monitoring functions, such as monitoring at

points between components, must specified via the DME

Designer application.

NOTE

These functions cannot be accessed from the ICP1.

Panel Operation and Displays

Spectrum Display

DME64N/DME24N Owner’s Manual

3. Select the desired monitor point from the

list.

The audio signal from the selected monitoring point

will be output via the PHONES jack and the

[MONITOR] indicator lights up.

Probe Monitor Functions

The Probe Monitor function allows monitoring points to

be selected from the DME Designer application. For

details, see the “DME Designer Owner’s Manual.”

When the Probe Monitor function is used the monitoring

point will change and the [MONITOR] indicator will flash.

Spectrum Display

The monitor functions also provide spectrum analyzer

type level display of the signal at the selected monitor

point.

Procedure

1. Select the monitor point for which you want

to see a spectrum display from the list.

2. Press the [ENTER] button.

A spectrum display of the audio signal at the

selected monitor point will appear.

Frequency

These are the separate frequency bands displayed.

Band Output Level

Signal level is displayed independently in 31 separate

frequency bands. Output level is displayed in 12 steps.

Peak Hold

When the peak hold function is ON, peak levels since

the current monitor point was selected are held

indefinitely. Peak levels are cleared after one second

when peak hold is OFF.

To turn the peak hold function ON or OFF, move the

cursor to the PEAK HOLD ON/OFF setting and press the

[ENTER] button to alternately turn it ON or OFF.

L/R Select

Indicates when the spectrum display is for the left or

right channel. The same spectrum display will be shown

for the L and R channels of all monitor points other than

user-defined points specified via the DME Designer

application.

To switch between the L and R displays move the cursor

to the CHANNEL L/R setting and press the [ENTER]

button to alternately select L or R.

NOTE

Press the [CANCEL] button to move back to the previous

edit display.

NOTE

When the monitoring function is set to ON

([MONITOR] indicator lit steadily), you can turn it

OFF by pressing the [MONITOR] button.

NOTE

The monitoring point selected in the DME64N/24N is

disabled.

NOTE

Spectrum display is not available on the ICP1 control

panel.

NOTE

The fall rate of the meters can be set up via the Utility

display “Disp” page.

Panel Operation and Displays

Level Meter Display

DME64N/DME24N Owner’s Manual

Level Meter Display

Individually displays the input/output level for each

channel.

1. Make sure that the Main display is showing.

If the Main display is not showing, press the

[CANCEL] to return.

2. Press the [UTILITY] button.

The level meter display will appear.

Level Display Slot

Select from [SLOT1] ~ [SLOT4], [AD/DA],

[CASCADE IN] or [CASCADE OUT].

Channel Number

A maximum of 32 [CASCADE IN]/[CASCADE OUT]

channels can be displayed, while for other channels a

maximum of 16 can be displayed.

Input/Output Level Display

Shows the levels at the individual inputs and outputs.

Peak Hold

When the peak hold function is set to ON, peak levels

are held indefinitely.

Peak levels are cleared after one second when peak

hold is set to OFF.

To turn the peak hold function ON or OFF, move the

cursor to the PEAK HOLD ON/OFF setting and press the

[ENTER] button to alternately turn it ON or OFF.

Initializing the DME64N/

DME24N

The DME64N/DME24N and ICP1 internal memories can

be initialized as follows.

Begin with the power turned off. Turn the power on while

holding the [SCENE] and [ENTER] buttons, and continue

to hold those buttons until the Yamaha logo appears.

The initialization screen will appear, allowing you to

choose one of the following three options.

01.Initialize DME:

All scenes, preset parameter settings and WAVE files

except components and files saved via the File Storage

function will be deleted. All UTILITY settings are reset to

their default values.

02.Delete All Data:

All internally-stored components, scenes, preset

parameters, wave files, and files stored using the File

Storage function are erased. All UTILITY settings are

reset to their default values. Use this problem when a

problem occurs with the data stored in the device. After

initialization, make sure to update the firmware and the

components from the DME Designer application.

Refer to the DME Designer Owner’s Manual for details.

03. ==> Exit Diag Mode:

Exits from the initialization screen and restarts the unit.

Do not turn off the power during initialization. Doing so

can damage the device.

NOTE

Level display is not available on the ICP1 control panel.

NOTE

[SLOT2] ~ [SLOT4] and [CASCADE IN], [CASCADE

OUT] are only available on the DME64N, while [AD/DA]

is only available on the DME24N.

HOME UTILITYSCENE LEVEL MUTE

ENTERCANCEL

1.Holding down the [SCENE] and [ENTER] buttons

2.Press the

[POWER]

button

Plug the PA-300 AC adaptor while

holding down the [SCENE] and

[ENTER] buttons

Panel Operation and Displays

Utility Displays

DME64N/DME24N Owner’s Manual

Utility Displays

Most basic DME64N/24N functions can be accessed via the Utility Display.

Items accessible via the Utility display

Page Item Description Manual Page

Info

Current status and settings for the devices basic parameters. Page 45

Label Name display.

Version The device’s current version number.

Date Current status and setup for the internal calendar/clock.

Battery Shows the status of the internal battery.

Net

Current status and settings for the Ethernet network. Page 46

MASTER/SLAVE Displays current status and determines whether the device is device group master or not.

IP Adr. Current status and setup for the device’s IP address.

Master ID Displays and sets the device group master host address.

Link Mode Current status and setup for the [NETWORK] connector.

MAC Adr. Displays the device’s MAC address.

Disp

Current status and setup for the display mode, etc. Page 46

LCD Contrast Current status and setup for display panel contrast.

LCD Backlight Current status and setup for the display panel backlight.

Meter Fall Time Current status and setup for meter fall time.

Lock

Current status and setup for panel lock and related functions. Page 47

Utility Current status and setup for the Utility display settings.

Panel Lock Boot Current status and setup for the DME64N/24N’s power-on panel lock status.

Panel Lock Target Current status and setup for the panel lock target.

User Defined Lock Panel lock and setup for each page of User Defined Button.

Misc

Current status and setup for settings not included in other pages. Page 48

Scene Store Current status and setup for scene store accessibility.

Last Mem. Resume Indicates and determines whether the previous memory contents will be retained when the

unit is restarted.

Event Scheduler Current status and setup whether an event schedule setup in the DME Designer will be

executed or not.

Remote

Rmt Ctrl Displays/sets the connector and connection type to be used for DME remote control

protocol communication.

Page 48

Int HA Ctrl Displays/sets the connector to be used for internal head amp control.

Ext HA Ctrl Displays/sets the type of connection to be used for external head amp control.

COM Displays/sets the type of connection to be used for DME protocol communication.

MIDI

Current status and setup for MIDI functions. Page 49

Port Current status and setup of the MIDI port.

Protocol Displays/sets the protocol to be used for communication with devices connected via MIDI.

CH Current status and setup for the MIDI transmit and receive channels.

Program Change Current status and setup for program change transmission/reception, omni on, and echo

on/off.

Control Change Current status and setup for control change transmission/reception, omni on, and echo

on/off.

Param Change Current status and setup for parameter change transmission/reception, omni on, and echo

on/off.

WCLK

Current status and selection of the DME64N/24N word clock. Page 50

Fs Displays the word clock frequency.

Int Current status of the internal word clock.

WCIN Current status of the word clock received at the [WORD CLOCK IN] connector.

Cascade Current status of the word clock received via the [CASCADE IN] and [CASCADE OUT]

connectors.

SLOT1-4 Current status of the word clock received via cards plugged in to the I/O card slots.

Panel Operation and Displays

Utility Displays

DME64N/DME24N Owner’s Manual

Slot

Displays info about an I/O card installed in a DME64N/24N I/O slot. Page 51

Card name Displays the name of the installed card.

(no title) Resets the installed card.

Format Displays the audio format – 88.2 or 96 kHz.

GPI

GPI connector calibration and status display. Page 51

Reset Resets the GPI calibration.

Max Sets the maximum calibration value.

Min Sets the minimum calibration value.

(no title) Current calibration status.

Current status and setup for the internal and connected external head amplifiers. Page 52

HA Current status and setup for head amplifier type.

WCLK Current status and setup for the word clock used by the head amplifier(s).

(no title) Displays the audio format 88.2/96 kHz.

Gain Current status and setup for individual head amplifier channel gain.

+48V Current status and setup for individual head amplifier channel phantom power supply (+48V

ON/OFF).

(no title) Displays current status of the master phantom power switch.

HPF Current status and setup for individual head amplifier channel high-pass filter on/off.

Frq Current status and setup for individual head amplifier channel high-pass filter frequency.

CASCAD

(DME64N

only)

Displays current status for the [CASCADE] connectors. Page 53

Head Margin Displays current status for the head margin of the audio signal handled via the [CASCADE]

connectors.

Unit No. Displays how many devices the unit is from the beginning of the cascade chain.

Mixer I/O Displays current status for the channels to be used for audio signals cascaded to a mixer.

Check

Mode Current status and setup for the thru connection. Page 54

Page Item Description Manual Page

Panel Operation and Displays

Utility Displays

DME64N/DME24N Owner’s Manual

Utility Display Operation

The general procedure for operating the Utility displays

is outlined below.

1. Press the [UTILITY] button for longer than

2 seconds from the Main display to go to

the Utility display.

2. Press the [UTILITY] button as many times

as necessary until the desired parameter

page appears.

3. Use the cursor buttons – [ E ] [  ] [  ] [ F ]

– to select the parameter you want to edit.

4. Press the [ENTER] button.

This either confirms a selection or edit, or calls the

appropriate parameter edit page.

Info Page

Label

Shows the name. The name can be changed via the

DME Designer application running on a computer

connected to the unit.

Program Version

This is the current firmware version number.

Date

Shows the currently set date and time. The internal clock

and calendar can be set here.

Edit using the “Numeric Parameters” editing procedure

described on page 36.

Battery

Shows the status of the internal battery. “Low Battery”

will appear when the battery needs to be replaced, and

“No Battery” will appear when no battery is present in

the device.

Daylight Saving Time

If you enable daylight saving time, the display will

indicate “DST.”

You can enable daylight saving time using DME

Designer from a connected computer.

NOTE

Press the [CANCEL] button to display the pages in

reverse order.

NOTE

On the ICP1 the function buttons are used in place of the

cursor buttons as follows:

[F1] button: Left

[F2] button: Up

[F3] button: Right

[F5] button: Down

NOTE

The date and time ( ) and the internal battery status

( ) are not shown on the ICP1 control panel display.

NOTE

The name can not be changed from the DME64N/24N

controls.

NOTE

“Zone slave” cannot be used to set this parameter.

Date/Time Parameter Edit Dialog

NOTE

Daylight saving time cannot be set on the DME64N/24N

itself.

Day - Month - Year

Hour : Minute : Second

Panel Operation and Displays

Utility Displays

DME64N/DME24N Owner’s Manual

Network Settings (Net) Page

Shows the Ethernet network address and other

parameters.

Master/Slave

Indicates whether or not the device is functioning as the

device group master: “Master” or “Slave.”

Master: the device is the device group master.

Slave: the device is a device group slave.

Edit using the “List Parameters” editing procedure

described on page 38.

IP Adr.

This is the device’s IP address.

Edit using the “Numeric Parameters” editing procedure

described on page 36.

Master ID

Displays and sets the device group master host

address.

Link Mode

Shows the status of the [NETWORK] connector. The

[NETWORK] connector can be set to operate in

“10Base-T” or “100Base-TX” mode.

10Base-T: The [NETWORK] connector is

compatible with 10Base-T operation.

100Base-TX: The 100Base-Tx: [NETWORK]

terminal operates as 100Base-TX if possible. If the

network environment does not support 100Base-

TX, it operates as 10Base-T.

Edit using the “List Parameters” editing procedure

described on page 38.

MAC Adr.

This is the device’s MAC (Media Access Control)

address.

Display Setup (Disp) Page

Provides access to a number of display parameters.

LCD Contrast

The current LCD contrast setting. This parameter can be

adjusted from 0% through 100%.

Edit using the “Numeric Parameters” editing procedure

described on page 36.

NOTE

Device group status of ICP1 is fixed to “Slave.” This

cannot be changed.

NOTE

Make sure that one device group master is assigned for

each device group.

If no device group master is assigned, no scene

information will appear on the display and scene-related

control will not be possible. Mute operations will also not

be possible.

NOTE

The network addresses of devices in the same device

group must be the same.

NOTE

Device group master's IP address can be changed via

the DME Designer application running on a computer

connected to the unit.

Network Address

Host Address

NOTE

This is not displayed on the device group master device.

NOTE

The MAC address is also known as the Ethernet

address, and is an independent address assigned to all

Ethernet devices. No two devices anywhere in the world

can have the same address.

NOTE

The meter fall time ( ) is not shown on the ICP1 control

panel display.

Panel Operation and Displays

Utility Displays

DME64N/DME24N Owner’s Manual

LCD Backlight

Specifies LCD backlight operation. Two settings are

available: “ON,” and “OFF.”

ON: The display is continuously lit.

OFF: The display lights when a control is operated,

and will go out 10 seconds after panel operation

ceases.

Pressing the [ENTER] button alternately selects “ON”

and “OFF”.

Meter Fall Time

Determines the fall time of the level meters – “Fast” or

“Slow.”

Fast: The meters rapidly follow changes in the

signal level.

Slow: The meters fall slower than the actual

changes in the signal level, allowing easier reading

in some cases.

Edit using the “List Parameters” editing procedure

described on page 38.

Security Setup (Lock) Page

Panel lock and related settings.

Utility

The lock status for the Utility display settings. This

parameter can be set to “Unlock” or “Lock.”

Unlock: The Utility display can be accessed

without a password.

Lock: A password must be entered to access the

Utility display.

When “Lock” is selected a password entry window will

appear when the [UTILITY] button is pressed to access

the utility pages.

Use the [ E ] and [ F ] buttons to position the cursor,

and the dial to enter the desired character at the cursor

location. When all of the password’s characters have

been entered as required press the [ENTER] button.

The password will also be required when switching from

the “Unlock” mode to the “Lock” mode.

Panel Lock Boot

Determines whether or not panel lock will be on when

power to the device is turned on. This parameter can be

set to “Unlock” or “Lock.”

Unlock: Panel lock is OFF when power to the

device is turned on.

Lock: Panel lock is ON when power to the device is

turned on.

Panel Lock Target

Determines the controls (control functions) to be affected

by panel lock. The available settings are “Key Only” and

“Key+GPI.”

Key Only: Panel lock only affects the panel

buttons.

Key+GPI: Panel lock applies to the panel buttons

as well as GPI control input.

User Defined Lock

Sets the lock status individually for each of the four User

Defined Button pages.

ON: The corresponding User Defined Button will

not appear on the display.

OFF: The corresponding User Defined Button will

appear on the display.

To change the settings use the [ E ] and [ F ] buttons to

move the cursor to the setting for the desired page, the

press the [ENTER] button to alternately turn the setting

“ON” and “OFF.”

NOTE

Password security and management is very important!

If you forget your password the unit cannot be operated!

If you forget your password contact the system

administrator.

If the password become unrecoverable for some reason

and you need to unlock the system, please contact your

Yamaha representative.

NOTE

See page 36 for details on how to use the Panel lock

feature.

NOTE

This parameter is displayed, but cannot be changed on

the ICP1 display.

NOTE

The User Defined Button are accessed as described in

the “Parameter Edit Display” section on page 36.

Panel Operation and Displays

Utility Displays

DME64N/DME24N Owner’s Manual

Miscellaneous Setup (Misc) Page

This page includes parameters not available in any other

page.

Scene Store

Determines whether or not scene store operations are

allowed. This parameter can be set to “Enable” or

“Disable.”

Enable: Scene store operations are allowed.

Disable: Scene store operations are prohibited.

Edit using the “List Parameters” editing procedure

described on page 38.

Last Mem. Resume

This parameter displays and determines whether the

DME64N/DME24N will recall the current scene when

started up, or whether the memory contents at the time

the unit was turned off will be recalled. The possible

settings are “ON” or “OFF”.

ON: The memory contents at the time the unit

was turned off will be recalled at startup.

OFF: The current scene will be recalled at

startup.

If “Last Mem. Resume” is set to ON, the unit will

back up data to the internal memory periodically.

In this case, do not turn off the power to the unit

within five (5) seconds after you operate any

parameters.

Event Scheduler

Determines whether an event schedule setup in the DME

Designer will be executed or not, and displays the

current status. This parameter can be set to “ON” or

“OFF.”

ON: The event will be executed.

OFF: The event schedule will not be executed.

Edit using the “List Parameters” editing procedure

described on page 38.

Remote Control Setup (Remote) Page

Rmt Ctrl (Remote Control)

Displays/sets the connector and connection type to be

used for DME remote control protocol* communication. If

the selected terminal was previously assigned to a

different function, a confirmation dialog will appear. Edit

using the “List Parameters” editing procedure described

on page 38.

OFF: Select “OFF” when this function is not to be

used.

Remote (232C): External controllers (AMX,

Crestron, etc.) control the DME64N/24N via the

[REMOTE] connector using an RS-232C

connection.

Remote (422): External controllers (AMX, Crestron,

etc.) control the DME64N/24N via the [REMOTE]

connector using an RS-422 connection.

Network: This setting allows the DME64N/24N to

be controlled via the [NETWORK] terminal. When

“Network” is selected it is also possible to select the

port number to be used.

NOTE

This item cannot be set if Internal HA Ctrl is set to

Remote.

NOTE

This setting applies to individual devices only. Even if

one DME64N/24N unit is set to “Disable,” scene store

operations will be possible via another DME64N/24N in

the same device group that is set to “Enable.”

NOTE

This parameter can be changed from the device group

master only.

CAUTION

NOTE

This parameter can be changed from the device group

master only.

NOTE

This page will not appear on the ICP1 display.

Panel Operation and Displays

Utility Displays

DME64N/DME24N Owner’s Manual

Int HA Ctrl (Internal head amp control)

Displays/sets the connector to be used for internal head

amp control. From a single digital mixer, you can control

the internal head amps of multiple DME series units

within the device group. Set this parameter only on the

DME series units that is connected directly to the digital

mixer, and turn in “OFF” for other units. Edit using the

“List Parameters” editing procedure described on page

38.

OFF: Select “OFF” when this function is not to be

used.

Remote (422): Allows a digital mixer to control the

internal head amps via RS-422 protocol.

Slot1 [Slot1 ~ Slot4 (DME64N)]: Allows a digital

mixer to control the internal head amps via the

specified expansion slot.

Ext HA Ctrl (External head amp control)

Displays/sets the type of connection to be used for

external head amp control.

OFF: Select “OFF” when this function is not to be

used.

Remote (422): Allows remote head amp control.

Always use this setting when a remote head amp

unit (AD8HR, AD824) is connected. Also, don’t

change the setting while a remote head amp is

connected. Doing so can damage the unit.

COM

Displays/sets the type of connection to be used for DME

protocol communication. This is a Yamaha maintenance

function. Normally, set this to “OFF”.

MIDI Setup (MIDI) Page

Port (MIDI port)

Sets/displays the port to be used for MIDI

communication. The available settings are: OFF,

Remote(232C), Remote(422), MIDI, USB-1, USB-2,

SLOT-1, SLOT-2, SLOT-3, and SLOT-4.

OFF: Select “OFF” when this function is not to be

used.

Remote (232C): MIDI data will be received via the

[REMOTE] connector using an RS-232C

connection.

Remote (422): MIDI data will be received via the

[REMOTE] connector using an RS-422 connection.

MIDI: The MIDI connector is the currently active

MIDI port.

USB-1, USB-2: The corresponding USB port is

selected for MIDI input.

Slot1 [Slot1 ~ Slot4 (DME64N)]: A card installed

in the corresponding I/O slot is currently selected

for MIDI input.

Edit using the “List Parameters” editing procedure

described on page 38.

NOTE

This page will not appear on the ICP1 display.

NOTE

When the DME64N/24N is functioning as the device

group master and is connected to a computer running

the DME Designer application via USB, the MIDI port

being used by the DME Designer will not be available.

Panel Operation and Displays

Utility Displays

DME64N/DME24N Owner’s Manual

Protocol (MIDI Protocol Setup)

Displays/sets the protocol to be used for communication

with devices connected via MIDI. The available settings

are: MIDI, DAW(Type1), and DAW(Type2).

MIDI: Use this setting when any MIDI device other

than a general-purpose ProTools controller (HUI

protocol) or general-purpose Logic or Cubase

controller (Mackie control protocol) is to be

connected.

DAW (Type1): Use this setting when a general-

purpose ProTools controller (HUI protocol) is to be

connected.

DAW (Type2): Use this setting when a general-

purpose Logic or Cubase controller (Mackie control

protocol) is to be connected.

Edit using the “List Parameters” editing procedure

described on page 38.

Refer to the DAW controller owner’s manual as well as

the DME Designer manual for setup details.

The following parameters are available when the

Protocol parameter is set to MIDI.

Specifies the device’s MIDI transmit and receive channel:

1 ~ 16.

Edit using the “List Parameters” editing procedure

described on page 38.

Program Change

Turns transmission and reception, the omni mode, and

echo ON or OFF for MIDI program change messages.

Move the cursor to the required parameter, then press

the [ENTER] button to alternately turn ON and OFF.

Control Change

Turns transmission and reception, the omni mode, and

echo ON or OFF for MIDI control change messages.

Move the cursor to the required parameter, then press

the [ENTER] button to alternately turn ON and OFF.

Parameter Change

Turns transmission and reception, and echo ON or OFF

for MIDI parameter change messages.

Move the cursor to the required parameter, then press

the [ENTER] button to alternately turn ON and OFF.

Word Clock Setup (WCLK) Page

Shows the status of incoming word clock signals, and

allows setup of the DME64N/24N master word clock.

Master Clock Selection Procedure

1. Use the cursor [ E ], [  ], [  ], [ F ], buttons

to select one of the square blocks

representing the available master clock

sources.

2. Press the [ENTER] button to select the

master clock.

The current sampling frequency of the master word

clock. The value shown here is determined by the

system’s master word clock signal. To select the word

clock to be used as the master, move the cursor to the

appropriate word clock indication in this display – the

[WORD CLOCK IN] clock, the cascade clock, or a slot

clock, for example – and press the [ENTER] button.

Int

Sets the frequency of the internal word clock – 44.1 kHz,

48 kHz, 88.2 kHz, or 96 kHz.

WCIN

Shows the status of the word clock signal at the [WORD

CLOCK IN] connector.

Cascade

Shows the status of the word clock signal at the

[CASCADE IN] and [CASCADE OUT] connectors.

NOTE

“DAW” stands for “Digital Audio Workstation.” ProTools,

Logic, and Cubase are DAW applications, and this

parameter provides direct compatibility with a number of

physical controls surfaces that are available for use with

these DAW software packages.

NOTE

This page will not be displayed on the ICP1.

Panel Operation and Displays

Utility Displays

DME64N/DME24N Owner’s Manual

SLOT1~4

Shows the status of the word clock signal input via I/O

cards installed in the I/O slots.

The Status Icons

Slot Information (Slot) Page

Displays the name of the card installed in an I/O card

slot. Some cards can also be reset via this page.

Card Name

The name of the installed card appears here.

Reset

Resets the installed card.

Format

Displays the 88.2/96 kHz audio signal transfer mode.

The input setting is on the left and the output setting is

on the right.

No Display (Default): 44.1/48 kHz audio signal

transfer.

SP (Double Speed): An 88.2/96 kHz capable card

is installed, allowing direct transfer at 88.2 or 96

kHz.

CH (Double Channel): A 44.1/48 kHz card is

installed, and 88.2 or 96 kHz audio is transferred by

using two 44.1/48 kHz channels to transfer each

channel of 88.2/96 kHz audio. The number of audio

channels that can be handled in this mode is half

the number of channels normally handled by the

card.

GPI Setup (GPI) Page

Input calibration parameters for the [GPI] connector.

Reset

Resets GPI calibration.

To reset the calibration, use the [ E ] [  ] [  ] [ F ]

buttons to select ALL to reset all inputs, or select an

individual input from 1 to 16 to be reset, then press the

[ENTER] button.

MAX

Sets the maximum calibration value.

To set the MAX value, use the [ E ] [  ] [  ] [ F ]

buttons to select ALL to set all inputs, or select an

individual input from 1 to 16 to be set, then press the

[ENTER] button to set the MAX value to the current input

voltage.

MIN

Sets the minimum calibration value.

To set the MIN value, use the [ E ] [  ] [  ] [ F ]

buttons to select ALL to set all inputs, or select an

individual input from 1 to 16 to be set, then press the

[ENTER] button to set the MIN value to the current input

voltage.

Calibration Info

Shows the calibration settings as well as the current

input voltage.

A word clock signal is present, and this signal can be

selected as the DME64N/24N word clock.

No word clock signal (cannot be selected as the master

clock).

A word clock signal is present, but is not in sync with

the master word clock.

Currently selected as the DME64N/24N word clock.

Currently selected as the DME64N/24N word clock, but

the clock signal is not useable.

Inactive slot channel, or no I/O card is present in the

slot.

NOTE

This page will not appear on the ICP1 display.

NOTE

This page will not appear on the ICP1 display.

Panel Operation and Displays

Utility Displays

DME64N/DME24N Owner’s Manual

Head Amplifier Setup (HA) Page

Provides access to the head amplifier settings. Refer to

“REMOTE Connection” on page 28 for head amplifier

control signal connection.

Internal Head Amplifier (DME24N only)

AD8HR

AD824

Specifies the type of head amplifier to be set up. The

available options are AD8HR, AD824, and Built-in HA

(DME24N only). When the AD8HR and AD824 are

selected, a number indicating the connection order will

also appear.

Edit using the “List Parameters” editing procedure

described on page 38.

WCLK (AD8HR/AD824 only)

Specifies the word clock signal to be used by the head

amplifier(s).

Available settings of the AD8HR are “D OUT A,” “WCLK

IN,” “INT44.1K,” “INT48K,” “INT88.2K,” and “INT96K.”

D OUT A: Sets the word clock signal at the digital

input as the master clock of the AD8HR.

WCLK IN: Sets the word clock signal at BNC

connector as the master clock of the AD8HR.

INT44.1K: Sets the 44.1 kHz internal word clock as

the master clock of the AD8HR.

INT48K: Sets the 48 kHz internal word clock as the

master clock of the AD8HR.

INT88.2K: Sets the 88.2 kHz internal word clock as

the master clock of the AD8HR.

INT96K: Sets the 96 kHz internal word clock as the

master clock of the AD8HR.

Available settings of the AD824 are “SLOT,” “BNC,”

“INT44.1K,” and “INT48K.”

SLOT A: Sets the word clock signal input via I/O

cards installed in the I/O slots as the master clock

of the AD824.

BNC: Sets the word clock signal at the BNC

connector as the master clock of the AD824.

INT44.1K: Sets the 44.1 kHz internal word clock as

the master clock of the AD824.

INT48K: Sets the 48 kHz internal word clock as the

master clock of the AD824.

Format (AD8HR only)

Displays the 88.2/96 kHz audio signal transfer mode.

The input setting is on the left and the output setting is

on the right.

No Display (default): 44.1/48 kHz audio signal

transfer.

SP (Double Speed): Allows direct transfer at 88.2

or 96 kHz.

CH (Double Channel): 88.2 or 96 kHz audio is

transferred by using two 44.1/48 kHz channels to

transfer each audio channel of 88.2 and 96 kHz

respectively. The number of audio channels that

can be handled in this mode is half the number of

channels normally handled by the AD8HR.

Gain

Individually sets the gain of each head amplifier channel.

Edit using the “Numeric Parameters” editing procedure

described on page 36.

NOTE

This page will not appear on the ICP1 display.

NOTE

Some scenes include head amplifier settings. In such

cases, the HA page settings will be saved along with the

scene when it is stored.

Panel Operation and Displays

Utility Displays

DME64N/DME24N Owner’s Manual

+48V

Individually turns phantom power ON or OFF for each

head amplifier channel.

Use the [ E ] and [ F ] buttons to position the cursor at

the desired channel, then press the [ENTER] button to

alternately turn phantom power for that channel ON and

OFF.

• Always turn the phantom power off when it is not

needed.

• When turning phantom power ON, make sure

that no equipment other than phantom-powered

devices such condenser microphones are

connected to the [IN] connectors (DME24N only).

Applying phantom power to a device that does

not require phantom power can damage the

device.

• Do not connect or disconnect a device to a [IN]

connector (DME24N only) while phantom power

is applied. Doing so can damage the connected

device and/or the unit itself.

• To prevent speaker and possible hearing

damage, be sure to turn power amplifiers OFF

when turning phantom power ON or OFF. It is

also a good idea to turn the output level all the

way down (page 39).

Phantom Master Switch (AD8HR only)

Displays overall phantom power ON or OFF.

High-pass Filter (HPF) (AD8HR only)

Individually turns the high-pass filter for each AD8HR

head amplifier channel ON or OFF. This parameter is

only available for the AD8HR head amplifier. Use the [ E

] and [ F ] buttons to select a channel, then press the

[ENTER] button to turn the HPF for that channel ON or

OFF.

High-pass Filter Frequency (Frq)

(AD8HR only)

Individually sets the high-pass filter frequency for each

AD8HR head amplifier channel. This parameter is only

available for the AD8HR head amplifier.

Edit using the “Numeric Parameters” editing procedure

described on page 36.

Cascade Setup (CASCAD) Page

Shows the status of the [CASCADE] connectors. Refer to

“CASCADE Connection” on page 31 for connection

details.

Settings are made from the DME Designer application

running on the connected computer.

Head Margin

Displays the head margin for cascade connection.

18dB: Use this setting when cascading DME64N

units or when connecting to a mixer’s normal

cascade bus.

0dB: Use this setting when connecting to a PM5D

in situations in which the PM5D SLOT OUT port

signal is being output via the CASCADE OUT

terminal.

Unit No

Shows how many devices the unit is from the beginning

of the cascade chain.

Mixer I/O

Displays whether the cascade signal is bus shared or

not.

: A DME64N connected directly to the mixer is

connected to a second DME64N on this

unidirectional channel.

Input on the same channel from other DME64N

units will be independent.



: This channel is being used for bidirectional bus

shared connection between DME64N units. Input

on the same

channel from other DME64N units will be summed.

NOTE

The gain of the DME24N internal head amplifiers can be

adjusted from +10 dB to –60 dB in 1-dB increments. The

internal circuitry switches at about the –45-dB point, and

the signal is automatically muted at that point to prevent

noise.

The AD8HR gain can be adjusted from +10 dB to –62 dB

in 1-dB steps, and the AD824 gain can be adjusted from

+10 dB to –62 dB in 6-dB steps.

The PAD will be internally switched on or off when the

gain of the DME24N built-in head amplifier is adjusted

between -8 dB and -7 dB. Keep in mind that noise may

be generated if there is a difference between the Hot

and Cold output impedance of the external device

connected to the IN connector when using phantom

power.

CAUTION

NOTE

This page only appears on the DME64N.

NOTE

The Head Margin setting only applies when connected

to a mixer. When the DME64N is connected to another

DME64N unit, head margin is fixed at 18 dB.

PM5D

DME64N DME64N

IN OUT

OUT

DME64N

IN OUT

Unit No = 01 Unit No = 02 Unit No = 03

Panel Operation and Displays

Utility Displays

DME64N/DME24N Owner’s Manual

Check Page

Even in an environment with no computer, you can check

the connections without using DME Designer by directly

connecting the DME64N/24N input/output.

The meter does not operate during a connection check.

MODE: OFF

Makes connections in the configuration used in the

current scene.

This is set to OFF when the unit is started.

MODE: Thru

Directly connects the Input and Output of each slot one-

to-one for each channel.

When input-only or output-only cards like AD or DA

cards are inserted in the slots, you cannot perform

checks in this mode.

In the DME24N, the internal AD and internal DA are

directly connected on each channel.

MODE: Summing

Sums all input signals coming from Inputs (-12dB),

without regard to device or card type, and outputs it

through all Outputs.

NOTE

Make sure that the Mixer I/O setting is the same for all

cascaded DME64N/24N units.

NOTE

This page will not appear on the ICP1 display.

References

Options

DME64N/DME24N Owner’s Manual

Options

The ICP1, CP4SW, CP1SF, and CP4SF controllers are available as options for remote external control of the DME series.

The ICP1 connects via Ethernet, while the CP4SW, CP1SF, and CP4SF connect via the GPI interface. For more

information on installing your Control Panel and connecting it to a DME series unit, refer to the owner’s manual that came

with the Control Panel. For more information on settings, refer to the DME Designer Owner’s Manual.

ICP1

This controller connects to a DME series unit via Ethernet. Like the DME series units, a unique IP address

must be assigned to each controller unit. Data is transmitted and received via Ethernet cables.

You can assign and control any function of all DME series units in the same device group via the controller.

Up to four parameter sets can be assigned to six function buttons (F1 – F6) located above and under the

LCD. You can control up to 24 parameters by selecting a display page using the [HOME] button.

CP4SW, CP4SF, and CP1SF

These controllers connect to DME series units via the [GPI] connectors. These controllers control only the

DME series units to which they are directly connected. The controller switches enable you to turn the pa-

rameter settings On and Off. The switch LEDs enable you to check the parameter status. The faders enable

you to control the parameter values.

References

CONTROL PANEL

CP4SW

CONTROL PANEL

CP1SF

CONTROL PANEL

CP4SF

References

Error Messages

DME64N/DME24N Owner’s Manual

Error Messages

Message Meaning Action

Error messages

Cannot Select No selectable items are available in the scene or

monitoring point list display.

Make the appropriate settings via the DME Designer

application.

Component Corrupt

Update Firmware!

The component data is corrupt or can’t be found. Restart after updating the component using DME

Designer. If the error indicators are still indicating the

error, execute the “Delete All Data” initialization. If the

problem persists, contact a Yamaha dealer.

Critical Battery The internal battery is almost discharged. Your data may

be lost.

If you turn off power to the unit, the current settings may

be lost and reset to the default values. Stop operating the

unit, and contact a Yamaha dealer for battery

replacement.

Int.Data Corrupt Data inside the internal flash memory has been erased. Execute the “Delete All Data” initialization. If the problem

persists, contact a Yamaha dealer.

Invalid Password An invalid password has been entered. Enter the correct password. If you have lost or forgotten

your password, contact a Yamaha dealer.

Log Buffer Full Saving is not possible, since the Event Log saving area is

full.

Use DME Designer to delete the log.

Low Battery The backup battery voltage is low. This does not affect the operation of the unit. However, if

you continue using the unit, the settings may be lost and

reset to the default values. Contact a Yamaha dealer for

battery replacement at your earliest convenience.

No Battery The internal battery is completely discharged or not

installed.

If you turn off the power to the unit, the current settings

will be lost and reset to the default values. Stop operating

the unit, and contact a Yamaha dealer for battery

replacement.

Param Access Err The current setting cannot be displayed because the

parameter you attempted to operate does not exist. It is

possible that the component is not operating normally.

Save the current settings using DME Designer, execute

the initialization (Delete All Data). If the problem persists,

contact a Yamaha dealer.

Param Set Err The current setting cannot be changed because the

parameter you attempted to operate does not exist. It is

possible that the component is not operating normally.

Save the current settings using DME Designer, execute

the initialization (Delete All Data). If the problem persists,

contact a Yamaha dealer.

ResumeData Corrupt

Recall a Scene!

The data has been partially corrupted due to power

shutdown while writing to the internal memory. The

current settings have been lost.

Recall the scene again. If the problem persists, contact a

Yamaha dealer.

Resume Data Lost!

Recall a Scene!

Current setting has been lost. Recall the scene again.

If the problem persists, contact a Yamaha dealer.

Saving Failed A save operation has failed. Stop using the device immediately and contact a

Yamaha dealer.

Slots Overloaded The current being used by all cards installed in I/O slots

exceeds the rated limit.

Make sure that the total current consumption of the cards

used does not exceed the limit.

Store Disable The scene store parameter is set to “Disable.” Set the scene store parameter to “Enable” via the Utility

display “Lock” page.

Storing Failed Either the flash memory for storing data is full, or the file

system has been damaged.

Reduce the number of unused scenes. Alternatively,

delete the files saved via the File Storage function. If

deleting these items does not solve the problem, execute

the Delete All Data initialization. If the problem persists,

contact a Yamaha dealer.

Status messages

Cable Disconnect No network cable connected. Make sure that a network cable is properly connected,

and that all network devices are functioning normally.

Cannot be assigned No parameter assigned. —

Cannot Store The scene data is protected. Set the protect parameter to “OFF” via the DME Designer

application.

CAS. In Sync Err The DME64N/24N clock is not in sync with the clock

signal being received at the [CASCADE IN] connector.

Make sure that the DME64N/24N and the card or external

source supplying the word clock are set to use the same

word clock.

CAS. Out Sync Err The DME64N/24N clock is not in sync with the clock

signal being received at the [CASCADE OUT] connector.

Make sure that the DME64N/24N and the card or external

source supplying the word clock are set to use the same

word clock.

Connection to Master

DME is Lost

Communication with the master DME device has been

interrupted.

Check that all cables are properly connected, and than

network switches, routers, and related devices are

functioning properly.

Connection to Slave

SME is Lost

Communication with the slave DME device has been

interrupted.

Check that all cables are properly connected, and than

network switches, routers, and related devices are

functioning properly.

References

Error Messages

DME64N/DME24N Owner’s Manual

Download Success The program has been successfully updated. —

Downloading

Do not turn off

Program update in progress. Do NOT turn power off

while the unit displays this message.

—

DSP Power Shortage Audio is not input or output and is muted due to

insufficient DSP resources.

This error sometimes occurs if you try to operate a

configuration at 96 kHz that has been created with a

word clock of 48 kHz. To operate a configuration at any

word clock setting, use DME Designer to create a

configuration with the word clock set to 96 kHz.

Duplicate IP Adr. Duplicate IP addresses. Change the IP addresses so that there are no duplicates.

Err: Wrong Device

Group Settings

The device group configuration set via DME Designer

does not match the actual configuration.

Use DME Designer to go off-line, create a configuration

that correctly matches the actual configuration, and then

go back on-line to synchronize the configuration.

Executing A User Defined Button operation is in progress. —

File Opening

Do not turn off

A file operation is in progress during which the computer

manipulates scene data. Do NOT turn power off while the

unit displays this message.

—

Illegal MAC Adr. An illegal MAC address has been encountered. This could be due to a hardware malfunction. Refer this

problem to a contact a Yamaha dealer.

Invalid IP Adr. The network IP address is not appropriate. Set an appropriate network IP address.

Network Busy There is too much network traffic. Communication is not

possible.

Check the devices connected to the network. If there are

too many devices connected, reduce the number of

devices.

Network Error One of the following errors has occurred on the network:

• A cable has been unplugged.

•

The power to a network switch or router has been shut off.

• A cable is in an inappropriate state (e.g. a heavy object

has been placed on the cable, etc.). Static electricity

can also cause errors.

Locate and eliminate the cause of the error.

Network Setup Preparing network connection. —

No Current Scene There is no data in the current scene. Send appropriate scene data from a computer running

the DME Designer application.

No MAC Adr. MAC address not specified. This could be due to a hardware malfunction. Refer this

problem to a Yamaha dealer.

Panel Locked Panel operation not allowed. Press the [CANCEL] button for longer than 2 seconds to

disengage panel lock and allow panel operation.

Panel Unlocked Panel lock has been disengaged. Panel operation is now

possible.

—

Recovering

Do not turn off

A program update attempt has failed, and the previous

program is currently being restored.

Do NOT turn power off while the unit is displaying this

message. If the update attempt repeatedly fails, there

may be a hardware malfunction. Refer this problem to a

Yamaha dealer.

Saving HA Info

Do not turn off

Head amplifier info save in progress.

(Do not turn power off.)

—

Saving Setup Info

Do not turn off

Info set up via the Utility display (other than head

amplifier info) is being saved.

(Do not turn power off.)

—

Scene Recalling

Do not turn off

Scene recall in progress. Do NOT turn power off while the

unit displays this message.

—

Scene Storing

Do not turn off

Scene store in progress. Do NOT turn power off while the

unit displays this message.

—

Searching for Master

DME Unit...

Currently searching for the master DME unit. —

Searching for Slave

DME Unit...

Currently searching for the slave DME unit. —

SLOT1 Sync Err The DME64N/24N clock is not synchronized with the

clock of the card installed in I/O slot 1.

Make sure that the DME64N/24N and the card or external

source supplying the word clock are set to use the same

word clock.

SLOT2 Sync Err The DME64N clock is not synchronized with the clock of

the card installed in I/O slot 2.

Make sure that the DME64N and the card or external

source supplying the word clock are set to use the same

word clock.

SLOT3 Sync Err The DME64N clock is not synchronized with the clock of

the card installed in I/O slot 3.

Make sure that the DME64N and the card or external

source supplying the word clock are set to use the same

word clock.

SLOT4 Sync Err The DME64N clock is not synchronized with the clock of

the card installed in I/O slot 4.

Make sure that the DME64N and the card or external

source supplying the word clock are set to use the same

word clock.

Message Meaning Action

References

Error Messages

DME64N/DME24N Owner’s Manual

Synchronizing

Do not turn off

Data is being received from the computer. Do NOT turn

power off while the unit displays this message.

—

Updating

Do not turn off

Data is being received from the computer. Do NOT turn

power off while the unit displays this message.

—

WCLK Unlocked A usable word clock signal is not being received or

cannot be detected.

Recheck all word clock connections and internal

parameters.

WCLK In Sync Err The DME64N/24N clock is not in sync with the clock

signal being received at the WORD CLOCK IN]

connector.

Make sure that the DME64N/24N and the card or external

source supplying the word clock are set to use the same

word clock.

Message Meaning Action

References

Troubleshooting

DME64N/DME24N Owner’s Manual

Troubleshooting

The power won’t turn on, and the panel

indicators and LCD won’t light.

• Is the power cable properly connected?

• Is the POWER switch turned on?

• If neither of the above is the problem, contact your Yamaha service center or representative.

Cannot exchange data between the

DME64N/24N and the DME Designer.

• Are the network cables connected correctly?

• Has the USB-MIDI driver been properly installed?

• If you are using the [NETWORK] connector, has the DME-N Network Driver been properly set up?

• Has a MIDI port been properly assigned (page 49)?

• Are you using a version of DME Designer later than 3.8?

No sound input. • Are the cables connected properly?

• Is an appropriate signal being received from the external device?

• Is the GAIN of the internal (DME24N) or external head amp set to an appropriate level?

No sound output. • Are the cables connected properly?

• Make sure that the output level isn’t turned down (page 39).

• Is MUTE ON (page 39)?

• Have you used DME Designer to select a scene that does not output audio?

• Are you attempting to run a configuration that is not compatible with 96 kHz operation at 96 kHz?

MIDI messages aren’t transmitted or

received.

• Is power to the MIDI device(s) turned on?

• Are the MIDI ports properly set up (page 49)?

• Are the receive and transmit device channels set appropriately?

Scenes are not recalled when MIDI

program change messages are

received.

• Have the settings required to receive program change messages been properly made (page 49)?

• Use the DME Designer to set up the MIDI Program Change table as required.

Parameter control does not function

even when MIDI control change

messages are received.

• Make the settings required to allow control change reception.

• Use the DME Designer to set up the MIDI Control Change table as required.

Parameter control does not function

even when MIDI parameter change

messages are received.

• Have the settings required to receive parameter change messages been properly made (page

49)?

• Use the DME Designer to set up the MIDI Parameter Change table as required.

Slow data transfer. • Set the LINK MODE to 100Base-TX (page 46).

The desired scene can’t be recalled. • Write the require scene data from the DME Designer to the DME64N/24N.

Scenes are recalled unexpectedly. • Is input being received from an external device or the DME Designer?

• Use the DME Designer to check the MIDI Program Change Table settings.

• Use the DME Designer to check the GPI input assignments.

• Use the DME Designer to check the Remote Control Setup List assignments.

Scenes can be recalled but not stored. • Set scene store to “Enable” (page 48).

The 96kHz/88.2kHz/48kHz/44.1kHz

indicator flashes red.

• Select a different word clock source (page 50).

• If an external device is functioning as the word clock master, check that the cables are connected

properly.

Noise appears on the analog outputs

when an external device is the word

clock master and the word clock source

is switched.

• Reduce the power amp level to prevent speaker damage, or turn the DME64N/24N off before

switching clock sources.

Use Defined Button settings change

unexpectedly.

• Use the panel lock function (page 38) to prevent unwanted operation of the panel controls on

specific DME64N/24N or ICP1 units.

User Defined Button settings cannot be

changed.

• Use the DME Designer to make sure that multiple User Defined Buttons are not assigned to the

same parameter.

• Turn the User Defined Lock function off (page 38).

The panel controls cannot be operated. • Is the panel lock function on (page 36)?

The Utility screen cannot be opened. • Is the Utility screen lock function on (page 47)? If you have forgotten your password contact your

Yamaha service center or representative.

References

Specifications

DME64N/DME24N Owner’s Manual

Specifications

Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to

change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not

be the same in every locale, please check with your Yamaha dealer.

*1. Available on DME24N only

European models

Purchaser/User Information specified in EN55103-1 and EN55103-2.

Inrush Current: 39A

Conforms to Environments: E1, E2, E3 and E4

Sampling Frequency

Internal 44.1kHz, 48kHz, 88.2kHz, 96kHz

External Normal Rate: 39.69 – 50.88kHz

Double Rate: 79.39 – 101.76kHz

Signal Delay (Fs = 96kHz)

DME64N: 0.85 msec (Input of MY8-AD96 to Output of MY8-DA96)

DME24N: 0.5 msec ([IN] port to [OUT] port)

Memory

Configuration 16 (depends on size of data)

Scene 999 (depends on size of data)

Display

160 x 64 dot matrix LCD with backlight

Scene No.

7-segment LED x 3

Indicators

Wordclock EXT.CLOCK, 96kHz, 88.2kHz, 48kHz, 44.1kHz

External Control NETWORK, MIDI

Zone Configuration MASTER

Analog Input*

SIGNAL x 8, PEAK x 8

Analog Output*

SIGNAL x 8, PEAK x 8

Power Requirements

120V AC, 60Hz (USA, Canada)

230V AC, 50Hz (Europe)

100V AC, 50/60Hz (Japan)

Power Consumption

DME64N: 80W

DME24N: 75W

Dimensions (W x H x D)

DME64N: 480 x 145 x 411.5mm, 3U

DME24N: 480 x 101 x 411.5mm, 2U

Weight

DME64N: 9.5kg

DME24N: 8kg

Temperature Range

Free-Air operating 10 – 35 °C

Storage -20 – 60 °C

AC Power Cord Length

2.5m

Supplied Accessories

AC power cord, Owner’s Manual, AC plug clamp, 16-pin Euroblock

plug x 2, 8-pin Euroblock plug x 4 (DME64N), 3-pin Euroblock plug x

16 (DME24N)

References

Input/Output Characteristics

DME64N/DME24N Owner’s Manual

Input/Output Characteristics

DME24N ANALOG INPUT CHARACTERISTICS

• 0dBu = 0.775 Vrms

• All AD converters (CH1-8) are 24-bit linear, 128 times oversampling.

• +48V DC (phantom power) is supplied to CH INPUT (1-8) connectors via

each individual controlled switch.

DME64N ANALOG OUTPUT CHARACTERISTICS

• 0dBu = 0.775 Vrms

• Stereo Phone Jack = unbalanced (Tip = LEFT, Ring = RIGHT, Sleeve =

GND)

DME24N ANALOG OUTPUT CHARACTERISTICS

• 0dBu = 0.775 Vrms

• All AD converters (CH1-8) are 24-bit linear, 128 times oversampling.

• Stereo Phone Jack = unbalanced (Tip = LEFT, Ring = RIGHT, Sleeve =

GND)

DME64N DIGITAL INPUT CHARACTERISTICS

DME64N DIGITAL OUTPUT CHARACTERISTICS

DME64N/24N ELECTRICAL CHARACTERISTICS

(Output impedance of signal generator: 150Ω)

* CH INPUT 1-8 and CH OUTPUT 1-8 are provided on the DME24 only.

Frequency Response 20Hz – 20kHz, reference to the nominal output level

@1kHz

Frequency Response fs = 96kHz@20Hz – 40kHz, reference to the nominal

output level @1kHz

Gain Error @1kHz

Total Harmonic Distortion fs = 48kHz

Total Harmonic Distortion fs=96kHz

Hum & Noise EIN = Equivalent Input Noise

• Hum & Noise are measured with a 6dB/octave filter @12.7kHz;

equivalent to a 20kHz filter with infinite dB/octave attenuation.

DME24N ELECTRICAL CHARACTERISTICS

Dynamic Range

• Dynamic range are measured with a 6dB/octave filter @12.7kHz;

equivalent to a 20kHz filter with infinite dB/octave attenuation.

Crosstalk@1kHz

Maximum Voltage Gain@1kHz

Phantom Voltage

PEAK/SIGNAL Indicator Level

Terminals Gain

Actual

Load

Impedance

For Use

With

Nominal

Input Level

Connector

Nominal

Max.

before clip

CH INPUT

1 – 8

-60dB 3kΩ 50 – 600Ω

Mics &

600Ω

Lines

-60dBu

(0.775mV)

-40dBu

(7.75mV)

Euroblock

+10dB +10dBu

(2.451V)

+30dBu

(24.511V)

Output

Te rmi na ls

Actual

Source

Impedance

For Use

With

Nominal

Output Level

Connector

Nominal

Max. before

clip

PHONES 15Ω 8Ω 75mW 150mW Stereo

Phone Jack

40Ω 65mW 150mW

Output

Te rmi na ls

Actual

Source

Impedance

For Use

With

Nominal

Output Level

Connector

Nominal

Max. before

clip

CH OUTPUT

1 – 8

75Ω 600Ω Lines +4dBu

(1.23V)

+24dBu

(12.28)

Euroblock

PHONES 15Ω 8Ω 75mW 150mW Stereo

Phone Jack

40Ω 65mW 150mW

Terminal Format Data Length Level Connector

CASCADE IN – 24-bit RS422 D-SUB Half Pitch connector 68P

(Female)

Terminal Format Data Length Level Connector

CASCADE OUT – 24-bit RS422 D-SUB Half Pitch connector 68P

(Female)

Input Output RL Conditions Min. Typ. Max. Units

CH INPUT

1 – 8

CH OUTPUT

1 – 8

600Ω GAIN = -60dB -1.5 0.0 0.5 dB

Internal

OSC

PHONES 8Ω -3.0 0.0 0.5 dB

Input Output RL Conditions Min. Typ. Max. Units

CH INPUT

1 – 8

CH OUTPUT

1 – 8

600Ω GAIN = -60dB -1.5 0.0 0.5 dB

Internal

OSC

PHONES 8Ω -3.0 0.0 0.5 dB

Input Output RL Conditions Min. Typ. Max. Units

CH INPUT

1 – 8

CH OUTPUT

1 – 8

600Ω GAIN = -60dB 2.0 4.0 6.0 dBu

GAIN = +10dB 2.0 4.0 6.0 dBu

Internal

OSC

PHONES 8Ω -30dBFS @1kHz,

phones level control:

max.

-2.0 0.0 2.0 dBu

Input Output RL Conditions Min. Typ. Max. Units

CH INPUT

1 – 8

CH OUTPUT

1 – 8

600Ω GAIN = -60dB

@20Hz – 20kHz

@+14dBu

0.1 %

GAIN = +10dB

@20Hz – 20kHz

@+14dBu

0.05 %

Internal

OSC

PHONES 8Ω -30dBFS @1kHz,

phones level control:

max.

0.1 %

Input Output RL Conditions Min. Typ. Max. Units

CH INPUT

1 – 8

CH OUTPUT

1 – 8

600Ω GAIN = -60dB

@20Hz – 20kHz

@+14dBu

0.1 %

GAIN = +10dB

@20Hz – 20kHz

@+14dBu

0.05 %

Internal

OSC

PHONES 8Ω -30dBFS @1kHz,

phones level control:

max.

0.1 %

Input Output RL Conditions Min. Typ. Max. Units

CH INPUT

1 – 8

CH OUTPUT

1 – 8

600Ω GAIN = -60dB

Master fader at

nominal level and

one Ch fader at

nominal level.

(Mixer mode)

-128

EIN

dBu

-64 dBu

600Ω GAIN = +10dB

Master fader at

nominal level and

one Ch fader at

nominal level.

(Mixer mode)

-82 dBu

– PHONES 8Ω Residual output

noise, phones level

control: min.

-86 dBu

Input Output RL Conditions Min. Typ. Max. Units

CH INPUT

1 – 8

CH OUTPUT

1 – 8

600Ω GAIN = +10dB 106 dB

From/To To / Fro m Conditions Min. Ty p. Max. Units

CH N CH (N-1) or

(N+1)

CH1 – 8, adjacent inputs -80 dB

Input Output RL Conditions Min. Typ. Max. Units

CH INPUT

1 – 8

CH OUTPUT

1 – 8

600Ω GAIN = -60dB 64 dB

Output Conditions Min. Typ. Max. Units

CH INPUT

1 – 8

hot, cold: No load 46 48 50 V

Input Output Conditions Min. Ty p. Max. Units

CH INPUT

1 – 8

– GAIN +10dB PEAK

red LED:ON

25 27 29 dBu

GAIN +10dB SIGNAL green

LED:ON

-12 -10 -8 dBu

– CH OUTPUT

1 – 8

PEAK red LED:ON 19 21 23 dBu

SIGNAL green LED:ON -18 -16 -14 dBu

References

Control I/O

DME64N/DME24N Owner’s Manual

Control I/O

DME64N: 16-GPI inputs and 16-GPI outputs

DME24N: 8-GPI inputs and 8-GPI outputs

Outputs: Imax/pin = 16mA

Outputs: VH = 2.5V(min.), VL = 0.6V(max.)

Terminals Format Level Connector

REMOTE - RS232C D-SUB Connector 9-pin (Male)

Baud Rate = 38,400 bps

Data = 8bit

Stop bit = 1bit

PARITY = NON

- RS422

MIDI IN/OUT/THRU - DIN Connector 5P

WORDCLOCK IN/OUT TTL/75Ω BNC Connector

Ethernet Ethernet - RJ-45

USB USB 0 – 3.3V USB Type B (Female)

GPI IN 0 – 5V Euroblock Connector

OUT TTL

+V 5V

References

Connector Pin Assign

DME64N/DME24N Owner’s Manual

Connector Pin Assign

[CASCADE IN/OUT] Connectors (DME64N only)

CASCADE IN CASCADE OUT

No.

Signal

No.

Signal

No.

Signal

No.

Signal

1 GND 35 GND 1 GND 35 GND

2 INPUT 1-2 (+) 36 INPUT 1-2 (-) 2 OUTPUT 1-2 (+) 36 OUTPUT 1-2 (-)

3 INPUT 3-4 (+) 37 INPUT 3-4 (-) 3 OUTPUT 3-4 (+) 37 OUTPUT 3-4 (-)

4 INPUT 5-6 (+) 38 INPUT 5-6 (-) 4 OUTPUT 5-6 (+) 38 OUTPUT 5-6 (-)

5 INPUT 7-8 (+) 39 INPUT 7-8 (-) 5 OUTPUT 7-8 (+) 39 OUTPUT 7-8 (-)

6 INPUT 9-10 (+) 40 INPUT 9-10 (-) 6 OUTPUT 9-10 (+) 40 OUTPUT 9-10 (-)

7 INPUT 11-12 (+) 41 INPUT 11-12 (-) 7 OUTPUT 11-12 (+) 41 OUTPUT 11-12 (-)

8 INPUT 13-14 (+) 42 INPUT 13-14 (-) 8 OUTPUT 13-14 (+) 42 OUTPUT 13-14 (-)

9 INPUT 15-16 (+) 43 INPUT 15-16 (-) 9 OUTPUT 15-16 (+) 43 OUTPUT 15-16 (-)

10 DTR IN (+) 44 DTR IN (-) 10 DTR OUT (+) 44 DTR OUT (-)

11 RTS OUT (+) 45 RTS OUT (-) 11 RTS IN (+) 45 RTS IN (-)

12 GND 46 GND 12 GND 46 GND

13 WORD CLOCK IN

(+)

47 WORD CLOCK IN (-) 13 WORD CLOCK OUT

(+)

47 WORD CLOCK OUT

(-)

14 WORD CLOCK OUT

(+)

48 WORD CLOCK OUT

(-)

14 WORD CLOCK IN

(+)

48 WORD CLOCK IN (-)

15 CONTROL IN (+) 49 CONTROL IN (-) 15 CONTROL OUT (+) 49 CONTROL OUT (-)

16 CONTROL OUT (+) 50 CONTROL OUT (-) 16 CONTROL IN (+) 50 CONTROL IN (-)

17 GND 51 ID6 IN 17 GND 51 ID6 OUT

18 GND 52 ID6 OUT 18 GND 52 ID6 IN

19 INPUT 17-18 (+) 53 INPUT 17-18 (-) 19 OUTPUT 17-18 (+) 53 OUTPUT 17-18 (-)

20 INPUT 19-20 (+) 54 INPUT 19-20 (-) 20 OUTPUT 19-20 (+) 54 OUTPUT 19-20 (-)

21 INPUT 21-22 (+) 55 INPUT 21-22 (-) 21 OUTPUT 21-22 (+) 55 OUTPUT 21-22 (-)

22 INPUT 23-24 (+) 56 INPUT 23-24 (-) 22 OUTPUT 23-24 (+) 56 OUTPUT 23-24 (-)

23 INPUT 25-26 (+) 57 INPUT 25-26 (-) 23 OUTPUT 25-26 (+) 57 OUTPUT 25-26 (-)

24 INPUT 27-28 (+) 58 INPUT 27-28 (-) 24 OUTPUT 27-28 (+) 58 OUTPUT 27-28 (-)

25 INPUT 29-30 (+) 59 INPUT 29-30 (-) 25 OUTPUT 29-30 (+) 59 OUTPUT 29-30 (-)

26 INPUT 31-32 (+) 60 INPUT 31-32 (-) 26 OUTPUT 31-32 (+) 60 OUTPUT 31-32 (-)

27 ID0 IN 61 ID1 IN 27 ID0 OUT 61 ID1 OUT

28 ID2 IN 62 ID3 IN 28 ID2 OUT 62 ID3 OUT

29 ID4 IN 63 ID5 IN 29 ID4 OUT 63 ID5 OUT

30 ID0 OUT 64 ID1 OUT 30 ID0 IN 64 ID1 IN

31 ID2 OUT 65 ID3 OUT 31 ID2 IN 65 ID3 IN

32 ID4 OUT 66 ID5 OUT 32 ID4 IN 66 ID5 IN

33 MSB //LSB IN 67 2CH//4CH IN 33 MSB //LSB OUT 67 2CH//4CH OUT

34 FG 68 FG 34 FG 68 FG

References

Connector Pin Assign

DME64N/DME24N Owner’s Manual

[NETWORK] Connector (100Base-TX Ethernet, RJ-45)

Straight/Cross Cable Wiring Details

Straight Cables Cross Cables

Pin Connection

1 TxD+

2 TxD–

3RxD+

4 Unused

5 Unused

6RxD–

7 Unused

8 Unused

Pins Pins

1 —— 1 1 —— 3

2 —— 2 2 —— 6

3 —— 3 3 —— 1

4 —— 4 4 —— 4

5 —— 5 5 —— 5

6 —— 6 6 —— 2

7 —— 7 7 —— 7

8 —— 8 8 —— 8

References

Dimensions

DME64N/DME24N Owner’s Manual

Dimensions

Unit: mm

DME64N

DME24N

480

132

145

394

405

12.5

388

411.5

278

53.5

300

423

17.5

18.5

4-M3

394

405

388

411.5

278

101

12.5

53.5

423

4-M3

480

300

References

MIDI Data Format

DME64N/DME24N Owner’s Manual

MIDI Data Format

1. DME64N/24N MIDI Functions

1.1 Scene Change

Scene recall occurs according to the “MIDI Program Change Table” assignments when appropriate MIDI

Bank Select MSB/LSB and Program Change messages are received by the DME64N/24N.

Corresponding MIDI Bank Select MSB/LSB and Program Change messages are also transmitted by the

DME64N/24N when a scene recall operation is carried out via the panel controls, as specified by the “MIDI

Program Change Table” assignments.

Transmission does not occur when switching Configurations.

1.2 Parameter Control

MIDI Control Change and Parameter Change messages transmitted to the DME64N/24N can be used to

control parameters according to the “MIDI Control Change table” and “MIDI Parameter Change Table”

assignments.

Corresponding MIDI Control Change and Parameter Change messages are also transmitted by the

DME64N/24N when a parameter is edited out via the panel controls, as specified by the “MIDI Control

Change table” and “MIDI Parameter Change Table” assignments.

2. MIDI Data Flow

SW1: Program Change Rx Switch [On/Off]

SW2: Control Change Rx Switch [On/Off]

SW3: Parameter Change Rx Switch [On/Off]

SW4: Program Change Echo Back Switch [On/Off]

SW5: Control Change Echo Back Switch [On/Off]

SW6: Parameter Change Echo Back Switch [On/Off]

SW7: Program Change Tx Switch [On/Off]

SW8: Control Change Tx Switch [On/Off]

SW9: Parameter Change

MIDI Rx CH: MIDI Rx Channel (1-16)

MIDI Tx CH: MIDI Tx Channel (1-16)

MIDI IN

MIDI OUT

MIDI Rx CH

Bank Select MSB/LSB

Program Change

(Scene Recall)

Bank Select MSB/LSB

Program Change

(Echo Back)

Bank Select MSB/LSB

Program Change

MIDI THRU

Control Change

(Parameter Edit)

Control Change

(Echo Back)

Control Change

Parameter Change

(Parameter Edit)

Parameter Change

(Echo Back)

MIDI Tx CH

SW1

SW2

SW3

SW4

SW5

SW6

SW7

SW8

SW9

References

MIDI Data Format

DME64N/DME24N Owner’s Manual

3. MIDI Setup

Specifies basic MIDI operation.

3.1 Host Select

Selects the input/output port to be used for MIDI communication.

3.2 DAW Controller

Specifies the DAW controller type when a DAW control surface is to be used to control the DME64N/24N.

When Type 1/2 is selected, Host Select is automatically set to MIDI.

3.3 MIDI Tx Channel

Specifies the MIDI transmit channel (1 ~ 16).

3.4 MIDI Rx Channel

Specified the MIDI receive channel (1 ~ 16).

3.5 MIDI Tx Switch

Program Change Tx Switch: turns Bank Select MSB, LSB, and Program Change transmission on or off.

Control Change Tx Switch: turns Control Change transmission on or off.

Parameter Change Tx Switch: turns Parameter Change transmission on or off.

3.6 MIDI Rx Switch

Program Change Rx Switch: turns Bank Select MSB, LSB, and Program Change reception on or off.

Control Change Rx Switch: turns Control Change reception on or off.

Parameter Change Rx Switch: turns Parameter Change reception on or off.

3.7 MIDI Omni Switch

Program Change Omni Switch: turns the Bank Select MSB, LSB, and Program Change omni mode on or

off.

Control Change Omni Switch: turns the Control Change omni mode on or off.

3.8 MIDI Echo Back Switch

Program Change Echo Back Switch: turns Bank Select MSB, LSB, and Program Change echo back on or

off.

Control Change Echo Back Switch: turns Control Change echo back on or off.

Parameter Change Echo Back Switch: turns Parameter Change echo back on or off.

4. MIDI Format

MIDI Format Chart (Rx: receive, Tx: transmit)

Number Format Notation

Numbers ending with “h” are in hexadecimal format, while numbers ending with “b” are binary format.

Characters “A” through “F” in hexadecimal numbers represent decimal values 10 through 15. Other

lowercase characters (usually “n” or “x”) represent any number.

Command Rx/Tx Function

Channel Message Control Change (Bnh) Rx/Tx Parameter Change

Program Change (Cnn) Rx/Tx Scene Recall

System Real-time Message ACTIVE SENSING (FEH) Rx MIDI Cable Check

System Exclusive Message Parameter Change Rx/Tx Parameter Change

References

MIDI Data Format

DME64N/DME24N Owner’s Manual

4.1 Program Change (Cnh)

Receive

When the “Program Change Rx Switch” is on, Program Change messages are received on the MIDI

channel specified by the “MIDI Rx Channel” parameter.

If the “Program Change Omni Switch” is also on, however, Program Change messages will be received on

all MIDI channels regardless of the “MIDI Rx Channel” setting.

When a Program Change message is received, the scene assigned to the received program number in the

“MIDI Program Change table” is recalled.

The accepted Bank Select, Program Change range is as follows:

Bank Select MSB: 0

Bank Select LSB: 0 ~ 7

Program Change No.: 0 ~ 127

Transmit

When the “Program Change Tx Switch” is on, the corresponding Program Change number will be

transmitted as specified by the “MIDI Program Change table” and “MIDI Tx Channel” settings.

If multiple Program Change numbers are assigned to a single scene, the Bank Select MSB/LSB and

Program Change number corresponding to the lowest number will be transmitted.

Bank Select MSB

Bank Select LSB

Program Change No.

4.2 Active Sensing (FEh)

Receive

MIDI communication will be initialized if no data is received within 300 ms after reception (Running Status,

etc., will be cleared).

Active Sensing

4.3 Control Change (Bnh)

Receive

When the “Control Change Rx Switch” is on, Control Change messages are received on the MIDI channel

specified by the “MIDI Rx Channel” parameter.

If the “Control Change Omni Switch” is also on, however, Control Change messages will be received on all

MIDI channels regardless of the “MIDI Rx Channel” setting.

Control Change parameter resolution is 128 regardless of the parameters effective range. For finer settings

use Parameter Change.

Transmit

When the “Control Change Tx Switch” is on, appropriate Control Change data will be transmitted when a

parameter is edited via the panel controls, as specified by the “MIDI Control Change table” and “MIDI Tx

Channel” settings.

Transmission does not occur when switching Configurations.

Refer to “Supplementary Information 1” for cases in which multiple messages are assigned to single

parameter.

4.4 Parameter Change (F0h ~ F7h)

Receive

When the “Parameter Change Rx Switch” is On, Parameter Change messages are received on the MIDI

channel specified by the “Device ID (Rx Ch)” parameter.

Status Bnh (1101nnnnb) Control Change

Data 00h (00000000b) Control Change No. 0 (Bank Select MSB)

Data nnh (0nnnnnnnb) Control Value (Bank Select MSB No.)

Status Bnh (1101nnnnb) Control Change

Data 20h (00100000b) Control Change No. 32 (Bank Select LSB)

nnh (0nnnnnnnb) Control Value (Bank Select LSB No.)

Status Cnh (1100nnnnb) Program Change

Data nnh (0nnnnnnnb) Program Change No. (0-127)

Status FEh (11111110b) Active Sensing

Status Bnh (1011nnnnb) Control Change

Data cch (0cccccccb) Control Change No. (1-31,33-95,102-119)

vvh (0vvvvvvvb) Control Value (0-127)

References

MIDI Data Format

DME64N/DME24N Owner’s Manual

Transmit

When the “Parameter Change Tx Switch” is On, appropriate Parameter Change data will be transmitted

when a parameter is edited via the panel controls, as specified by the “MIDI Parameter Change table” and

“MIDI Tx Channel” settings.

Refer to “Supplementary Information 1” for cases in which multiple messages are assigned to single

parameter.

Refer to “Supplemental Information 2” for information on setting Parameter Data values.

Supplemental Information 1

Messages Transmitted When Multiple Messages are Assigned to the Same Parameter

The DME64N/24N MIDI transmit messages are specified via the “MIDI Control Change Table” and “MIDI

Parameter Change Table.” The “MIDI Control Change Table” and “MIDI Parameter Change Table” can be

set up via the DME Designer application.

Multiple messages can be assigned to a single parameter, but the DME64N/24N will only transmit one of

the assigned messages.

The transmitted messages are as follows:

• If a Control Change message and a Parameter Change message are assigned to the same parameter 

the Control Change message will be transmitted.

• If multiple Control Change numbers are assigned to the same parameter  the smallest Control Change

number message will be transmitted.

• If multiple Parameter Change numbers are assigned to the same parameter  the smallest Parameter

Change number message will be transmitted.

Supplemental Information 2

Setting the Parameter Change Message Parameter Data Values

The Parameter change parameter values are expressed as 32-bit integers with or without parity.

• A parity bit (positive: 0, negative: 1) is added above the most significant value bit (bit 31).

• Fractional parameters will be converted according to the integer table.

• For integers with parity, negative numbers are expressed as the 2’s complement.

Status F0h (11110000b) System Exclusive Message

ID No. 43h (01000011b) Manufacturer's ID No.(YAMAHA)

DEVICE ID. 10h (0001xxxxb) Rx/Tx Channel (0-15)

GROUP ID. 3Eh (00111110b) Digital Mixer

MODEL ID. 10h (00010000b) Device Code (DME)

Parameter

Address

aah (0aaaaaaab) Parameter Address High

aah (0aaaaaaab) Parameter Address Low

Parameter

Data Value

ddh (0dddddddb) data 0

ddh (0dddddddb) data 1

ddh (0dddddddb) data 2

ddh (0dddddddb) data 3

ddh (0dddddddb) data 4

EOX F7h (11110111b) End of Exclusive

sign

Example

• When value is 1000 (decimal) / 3E8h (hexadecimal):

• When value is 1000 (decimal) / FFFFFC18h (hexadecimal; 2’s complement of 3E8h):

References

MIDI Data Format

DME64N/DME24N Owner’s Manual

MIDI Data Format

TransmittedFunction... Recognized Remarks

Basic

Channel

Note

Number : True voice

Velocity

After

Touch

Pitch Bend

Control

Change

Prog

Change : True #

System Exclusive

: Song Pos.

Common : Song Sel.

: Tune

System : Clock

Real Time : Commands

: All Sound Off

Aux :

Reset All Cntrls

: Local ON/OFF

Mes- : All Notes OFF

sages : Active Sense

: Reset

Notes:

Mode

Default

Changed

Note ON

Note OFF

Key’s

Ch’s

0,32

1-31,33-95,102-119

1 - 16

O *1

O *2

O 0 - 127 *1

**************

not include “DAW controller” command

*1 transmit/receive if program change switch is on.

*2 transmit/receive if control change switch is on.

*3 transmit/receive if parameter change switch is on.

**************

O *3

Mode 1 : OMNI ON , POLY Mode 2 : OMNI ON , MONO

Mode 3 : OMNI OFF, POLY Mode 4 : OMNI OFF, MONO

1 - 16

O *1

O *2

O *3

O : Yes

× : No

Default

Messages

Altered

YAMAHA [Digital Mixing Engine] Date :31-MAR-2004

Model DME64N/24N MIDI Implementation Chart Version : 1.0

Memorized

Bank Select

Assignable

O 0 - 127 *1

0 - 127

Assignable

References

Glossary

DME64N/DME24N Owner’s Manual

Glossary

Terms Explanations

100Base-TX

A physical specification for a 100 Mbps Ethernet network connection using 2-conductor

Category 5 UTP cable included in the IEEE 802.3u standard. Maximum data transfer

distance is 100 meters.

10Base-T

A physical specification for a 10 Mbps Ethernet network connection using 2-conductor

Category 3 UTP cable included in the IEEE 802.3i standard. Maximum data transfer

distance is 100 meters.

BNC (Bayonet Nut Connector,

or Bayonet Neill Concelman)

A type of connector used for high-frequency connections using thin-core coaxial cable.

An internal spring ensures a solid connection.

Cascade

A means of connecting Yamaha digital audio equipment to allow transfer of audio, control,

and word clock signals. Yamaha cascade connections employ half-pitch 68-pin D-Sub

connectors.

Category 3

Electrical specifications for one type of UTP cable jointly developed by the TIA

(Telecommunications Industry Association) and EIA (Electronic Industry Alliance). Several

categories are specified according to electrical characteristics, with higher category

numbers denoting higher quality cable. Category 3 cable can be used for transmission

speeds up to 10 MHz.

Category 5

Electrical specifications for one type of UTP cable jointly developed by the TIA

(Telecommunications Industry Association) and EIA (Electronic Industry Alliance). Several

categories are specified according to electrical characteristics, with higher category

numbers denoting higher quality cable. Category 5 cable can be used for transmission

speeds up to 100 MHz.

Component

The basic modules that are combined to create DME64N/24N audio systems. In addition to

complete audio processors such as mixers, compressors, effects, crossovers, etc., a range

of smaller functions such as faders, switches, pan controls, and meters are also available.

Components can also be customized.

Configuration

A set of components and connections that make up an audio system in the DME64N/24N.

D-Sub

Another common form of connector that gets its name from the “D” shape of the connector.

This type of connector can be securely attached using screws. Individual “pins” are used to

connect each of the cable’s conductors. D-Sub connectors come in 9-pin, 15-pin, 25-pin,

37-pin, and other sizes.

DSP (Digital Signal processor)

A semiconductor chip (LSI), or device containing one or more such chips, developed

specifically to process large volumes of data in real time. Ideal for processing digital audio.

Ethernet

A network protocol jointly developed by the Xerox, DEC, and Intel corporations, and

codified in the IEEE 802.3 industry standard. Transfer speeds have increased to 100 Mbps,

1000 Mbps, and 10 Gbps from the initial 10 Mbps, while maintaining network compatibility.

Euroblock

A connector system consisting of plug and socket components that allows easy, solder-less

wiring for a range of installations and devices. Simply insert the wire into the plug slot,

tighten the screw, and plug into the socket to complete the connection.

GPI (General Purpose Interface)

A general-purpose control interface that can be used to allow control of the DME64N/24N

via external devices and custom-made controllers. Connections are made via a Euroblock

connector. The optional CP4SW, CP1SF, and CP4SF control panels also connect via GPI.

Initial Settings

The initial values and settings of all editable parameters that will be in effect when a device

is powered on for the first time after it is shipped from the factory. Also known as “default

settings” or “initial factory settings.”

MAC (Media Access Control) Address

The MAC address is also known as the Ethernet address, and is an independent address

assigned to all Ethernet devices worldwide. No two devices can have the same address.

MIDI (Musical Instrument Digital Interface)

An international standard for data communication between electronic musical instruments

and audio devices.

Mini YGDAI (Yamaha General Digital Audio

Interface) card

A standard for I/O cards that can be installed to Yamaha audio products.

Phantom Power

A power delivery system that allows power to be delivered to devices along with audio

signals via standard balanced audio cables. The term “phantom” is applied because the

system uses the audio conductors for power delivery without disrupting the audio signal

– the power is not “seen” by the audio signal.

Preset Parameter

The parameter set of all components included in a configuration.

RJ-45

An 8-conductor modular connector used for Ethernet cable and ISDN telephone

connections. The appearance is similar to the RJ-11 connectors used for telephone lines,

but the connector is actually somewhat larger. “RJ” stands for “Registered Jack,” and is a

connector type included in the Bell System USOC (Universal Service Ordering Codes)

standards.

Router

An equipment that relays data in network by selecting the most effective route.

References

Glossary

DME64N/DME24N Owner’s Manual

RS-232C

A serial communication protocol that allows data transfer over distances of up to 15 meters.

RS232C interfaces usually employ 9-pin D-sub connectors. “RS” stands for

“Recommended Standard,” and one of the standards developed by the EIA (Electronic

Industry Alliance).

RS-422

A balanced serial communication protocol that allows data transfer over distances of up to

1 kilometer. RS-422 offers higher data rates and greater reliability than the RS-232C

protocol.

Sampling Frequency

The number of times per second an analog audio signal is “sampled” when it is being

converted to digital audio.

Scene

A complete audio setup including configuration data and the related component preset

parameters. Up to 999 scenes can be stored for each zone in a DME64N/24N audio

system.

STP (Shielded Twisted Pair) Cable

A data transmission cable consisting of a shielded twisted pair. This type of cable is more

resistant to noise and interference than UTP (Unshielded Twisted Pair) cable.

Network Switch

A network switch which automatically connects only ports through which communication is

currently taking place. This reduces network load while maximizing security. This type of

switch can often mediate between devices having different transmission speeds and

standards.

USB (Universal Serial Bus)

A serial bus primarily used for connecting peripheral devices to computer equipment.

The USB 1.1 standard allows data transfer rates of up to 12 Mbps.

UTP (Unshielded Twisted pair) Cable

A data transmission cable consisting of an unshielded twisted pair. This type of cable is less

expensive and more commonly available than STP (Shielded Twisted Pair) cable, and is

widely used in 10Base-T and 100Base-TX network connections.

Word Clock

A signal used to synchronize multiple interconnected digital audio devices. The word clock

frequency will be the same as the sampling frequency of the audio signal being processed.

Terms Explanations

DME64N/24N Owner’s Manual

+48V ............................................................................53

[ E ] [  ] [  ] [ F ] Buttons 15

100Base-TX (Glossary) ............................................... 71

10Base-T (Glossary) ....................................................71

[96kHz] [88.2kHz] [48kHz] [44.1kHz] Indicator ............14

[AC IN] Connector ........................................................ 16

area ................................................................................9

audio ............................................................................11

Band Output Level .......................................................41

Battery .........................................................................45

BNC (Bayonet Nut Connector, or Bayonet Neill Concelman)

(Glossary)

.....................................................................71

cable clamp ..................................................................18

Calibration Info ............................................................. 51

[CANCEL] Button .........................................................15

Card Name ..................................................................51

CASCAD Page ............................................................53

Cascade (Glossary) .....................................................71

Cascade (WCLK Page) ............................................... 50

CASCADE connection ................................................. 31

[CASCADE IN] [CASCADE OUT] Connectors ......17, 31

cascade loop ................................................................ 31

Cascade Setup (CASCAD) Page ................................53

Category 3 (Glossary) ..................................................71

Category 5 (Glossary) ..................................................71

CH (Double Channel) (Slot Page) ............................... 51

CH (MIDI Page) ...........................................................50

component (Glossary) .................................................71

Components .................................................................. 9

Configuration .................................................................9

configuration (Glossary) ...............................................71

connector pin assign ....................................................63

Control Change ............................................................ 50

control I/O ....................................................................62

CP4SW, CP4SF, and CP1SF ......................................55

Date .............................................................................45

Device control ..............................................................11

device group ..................................................................9

Device Group (Net Page) ............................................ 46

Device group control .................................................... 11

Dial ...............................................................................15

dimensions ...................................................................65

Disp Page ....................................................................46

Display ......................................................................... 15

Display Setup (Disp) Page ........................................... 46

DME Designer ............................................................. 13

DME-N Network Driver ................................................ 23

DSP (Digital Signal processor) (Glossary) ................... 71

D-Sub (Glossary) ......................................................... 71

[ENTER] Button ........................................................... 15

Error Messages ........................................................... 56

Ethernet (Glossary) ...................................................... 71

Ethernet Connection .................................................... 23

Euroblock ..................................................................... 26

Euroblock (Glossary) ................................................... 71

[EXT. CLOCK] Indicator ............................................... 14

Format (HA Page) ........................................................ 52

Format (Slot Page) ...................................................... 51

Frequency .................................................................... 41

front panel .................................................................... 14

Frq ............................................................................... 53

Fs ................................................................................. 50

Gain ............................................................................. 52

GPI (General Purpose Interface) ................................. 33

GPI (General Purpose Interface) (Glossary) ............... 71

GPI connection ............................................................ 33

[GPI] Connector ..................................................... 16, 33

Ground Screw .............................................................. 16

HA ................................................................................ 52

HA Page ...................................................................... 52

Head Amplifier Setup (HA) Page ........................... 52, 54

Head Margin ................................................................ 53

High-pass Filter ............................................................ 53

High-pass Filter Frequency .......................................... 53

[HOME] Button ............................................................. 15

HPF .............................................................................. 53

I/O card ........................................................................ 20

I/O card (installation procedure) .................................. 21

I/O Slots ....................................................................... 17

ICP1 ............................................................................. 55

[IN] [OUT] Connectors ........................................... 17, 26

Info Page ..................................................................... 45

initial settings (Glossary) .............................................. 71

Index

DME64N/24N Owner’s Manual

Input/Output Level Display ...........................................42

Int ................................................................................. 50

IP Adr. ..........................................................................46

L/R Select ....................................................................41

Label ............................................................................45

LCD Backlight ..............................................................47

LCD Contrast ...............................................................46

[LEVEL] Button ............................................................15

Level Meter display ......................................................42

Link Mode ....................................................................46

List Parameter .............................................................38

Lock Page .................................................................... 47

MAC (Media Access Control) Address (Glossary) ....... 71

MAC Adr. .....................................................................46

Main display ................................................................. 35

[MASTER] Indicator .....................................................15

MAX .............................................................................51

Meter Fall Time ............................................................47

MIDI (Musical Instrument Digital Interface) (Glossary)

.. 71

MIDI connection ........................................................... 30

MIDI Data Format .................................................. 66, 70

[MIDI IN] [MIDI OUT] [MIDI THRU] Connectors ..........16

[MIDI] Indicator ............................................................15

MIDI Page .................................................................... 49

MIDI Setup (MIDI) Page ..............................................49

MIN ..............................................................................51

Mini YGDAI (Yamaha General Digital Audio Interface)

card (Glossary) ............................................................71

Misc Page ....................................................................48

Miscellaneous Setup (Misc) Page ............................... 48

Mixer I/O ......................................................................53

[MONITOR] Button ......................................................15

Monitoring ....................................................................40

[MUTE] Button ............................................................. 15

Mute Indicator ..............................................................35

Mute Switching ............................................................39

Net Page ...................................................................... 46

[NETWORK] Connector ......................................... 17, 23

[NETWORK] Indicator ..................................................14

Network Settings .......................................................... 22

Network Settings (Net) Page .......................................46

Network Switch (Glossary) .......................................... 72

Numeric Parameter ......................................................36

ON/OFF Parameter ..................................................... 38

Options ........................................................................55

Output Level Control ....................................................39

Output Level Indicator ..................................................35

Page Scroll Bar ............................................................ 35

Panel Lock ................................................................... 36

Panel Lock Boot ........................................................... 47

Panel Lock Icon ........................................................... 35

Panel Lock Target ........................................................ 47

Parameter Change ...................................................... 50

Parameter Edit display ................................................. 36

Peak Hold (Level Meter display) .................................. 42

Peak Hold (Spectrum display) ..................................... 41

[PEAK] Indicator .......................................................... 15

Phantom Master Switch ............................................... 53

Phantom Power (Glossary) .......................................... 71

[PHONES] Jack ........................................................... 15

[PHONES LEVEL] Control ........................................... 15

Port (MIDI Page) .......................................................... 49

[POWER] Switch .......................................................... 15

preparation ............................................................. 18, 26

preset parameter (Glossary) ........................................ 71

Probe Monitor Function ............................................... 41

Program Change ......................................................... 50

Protocol (MIDI Page) ................................................... 50

rear panel ..................................................................... 16

Remote Connection ..................................................... 28

[REMOTE] Connector ............................................ 17, 28

Remote Page ............................................................... 48

Reset (GPI Page) ........................................................ 51

Reset (Slot Page) ........................................................ 51

RJ-45 (Glossary) .......................................................... 71

router (Glossary) .......................................................... 71

RS-232C (Glossary) .................................................... 72

RS-422 (Glossary) ....................................................... 72

sampling frequency (Glossary) .................................... 72

Scene ........................................................................... 10

scene (Glossary) .......................................................... 72

Scene Information ........................................................ 35

[SCENE NUMBER] Indicator ....................................... 15

Scene Recall ................................................................ 39

Scene Store (Misc Page) ............................................. 48

Scene Store (Operation) .............................................. 40

security cover mounting ............................................... 18

Security Setup (Lock) Page ......................................... 47

[SIGNAL] Indicator ....................................................... 15

Slot Information (Slot) Page ......................................... 51

Slot Page ..................................................................... 51

SLOT1~4 ..................................................................... 51

SP (Double Speed) ...................................................... 51

specifications ............................................................... 60

Spectrum display ......................................................... 41

status message ............................................................ 56

STP (Shielded Twisted Pair) Cable (Glossary) ............ 72

DME64N/24N Owner’s Manual

troubleshooting ............................................................ 59

Unit No .........................................................................53

USB (Universal Serial Bus) (Glossary) ........................ 72

USB Connection .......................................................... 22

[USB] Connector .......................................................... 14

USB-MIDI Driver .......................................................... 22

User Defined button .......................................................9

User Defined Button (Edit) ........................................... 38

User Defined Button Names ........................................35

User Defined buttons (User Defined parameters) .........9

User Defined Lock ....................................................... 47

Utility (Lock Page) ........................................................ 47

[UTILITY] Button ..........................................................15

Utility display ................................................................ 43

Utility display (Operation) ............................................. 45

UTP (Unshielded Twisted pair) Cable (Glossary) ........ 72

Version .........................................................................45

WCIN ...........................................................................50

WCLK (HA Page) .........................................................52

WCLK Page ................................................................. 50

Word Clock (Glossary) .................................................72

WORD CLOCK connection .......................................... 32

[WORD CLOCK IN] [WORD CLOCK OUT] Connectors

................................................................................16, 32

word clock master ........................................................ 32

Word Clock Setup (WCLK) Page .................................50

word clock slave .......................................................... 32

zones ............................................................................. 9

DME64N/24N Owner’s Manual

MEMO

DME64N/24N Owner’s Manual

MEMO

DME64N/24N Owner’s Manual

MEMO

For details of products, please contact your nearest Yamaha

representative or the authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou

au distributeur le plus proche de vous figurant dans la liste suivante.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten

Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más

cercana o el distribuidor autorizado que se lista debajo.

HEAD OFFICE

Yamaha Corporation, Pro Audio Division

Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2441

PA26'

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

U.S.A.

Tel: 714-522-9011

MEXICO

Yamaha de México S.A. de C.V.

Calz. Javier Rojo Gómez #1149,

Col. Guadalupe del Moral

C.P. 09300, México, D.F., México

Tel: 55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi,

CEP 04534-013 Sao Paulo, SP. BRAZIL

Tel: 011-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.

Sucursal de Argentina

Olga Cossettini 1553, Piso 4 Norte

Madero Este-C1107CEK

Buenos Aires, Argentina

Tel: 011-4119-7000

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso 7, Urbanización Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, Panamá

Tel: +507-269-5311

THE UNITED KINGDOM

Yamaha Music U.K. Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 01908-366700

GERMANY

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Europe GmbH

Branch Switzerland in Zürich

Seefeldstrasse 94, 8008 Zürich, Switzerland

Tel: 01-383 3990

AUSTRIA

Yamaha Music Europe GmbH Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

CZECH REPUBLIC/SLOVAKIA/

HUNGARY/SLOVENIA

Yamaha Music Europe GmbH Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-602039025

POLAND

Yamaha Music Europe GmbH

Branch Sp.z o.o. Oddzial w Polsce

ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland

Tel: 022-868-07-57

THE NETHERLANDS/

BELGIUM/LUXEMBOURG

Yamaha Music Europe Branch Benelux

Clarissenhof 5-b, 4133 AB Vianen, The Netherlands

Tel: 0347-358 040

FRANCE

Yamaha Musique France

BP 70-77312 Marne-la-Vallée Cedex 2, France

Tel: 01-64-61-4000

ITALY

Yamaha Musica Italia S.P.A.

Combo Division

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha Música Ibérica, S.A.

Ctra. de la Coruna km. 17, 200, 28230

Las Rozas (Madrid), Spain

Tel: 91-639-8888

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1, Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

YS Copenhagen Liaison Office

Generatorvej 6A, DK-2730 Herlev, Denmark

Tel: 44 92 49 00

NORWAY

Norsk filial av Yamaha Scandinavia AB

Grini Næringspark 1, N-1345 Østerås, Norway

Tel: 67 16 77 70

RUSSIA

Yamaha Music (Russia)

Room 37, bld. 7, Kievskaya street, Moscow, 121059,

Russia

Tel: 495 626 5005

OTHER EUROPEAN COUNTRIES

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: +49-4101-3030

Yamaha Corporation,

Asia-Pacific Sales & Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2303

TURKEY/CYPRUS

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

OTHER COUNTRIES

Ya m a h a M u sic G u l f F Z E

LOB 16-513, P.O.Box 17328, Jubel Ali,

Dubai, United Arab Emirates

Tel: +971-4-881-5868

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,

Shanghai, China

Tel: 021-6247-2211

INDIA

Yamaha Music India Pvt. Ltd.

5F Ambience Corporate Tower Ambience Mall Complex

Ambience Island, NH-8, Gurgaon-122001, Haryana, India

Tel: 0124-466-5551

INDONESIA

PT. Yamaha Music Indonesia (Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 21-520-2577

KOREA

Yamaha Music Korea Ltd.

8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,

Kangnam-Gu, Seoul, Korea

Tel: 080-004-0022

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,

Petaling Jaya, Selangor, Malaysia

Tel: 3-78030900

SINGAPORE

Yamaha Music Asia Pte., Ltd.

#03-11 A-Z Building

140 Paya Lebor Road, Singapore 409015

Tel: 747-4374

TAIWAN

Yamaha KHS Music Co., Ltd.

3F, #6, Sec.2, Nan Jing E. Rd. Taipei.

Taiwan 104, R.O.C.

Tel: 02-2511-8688

THAILAND

Siam Music Yamaha Co., Ltd.

4, 6, 15 and 16th floor, Siam Motors Building,

891/1 Rama 1 Road, Wangmai,

Pathumwan, Bangkok 10330, Thailand

Tel: 02-215-2626

OTHER ASIAN COUNTRIES

Yamaha C o r p o ration,

Asia-Pacific Sales & Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2303

AUSTRALIA

Yamaha M u s i c Austra l i a P t y. Lt d .

Level 1, 99 Queensbridge Street, Southbank,

Victoria 3006, Australia

Tel: 3-9693-5111

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha C o r p o ration,

Asia-Pacific Sales & Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2303

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

WW20480

U.R.G., Pro Audio Division

1009MWTO-F0

Printed in Japan

Yamaha Pro Audio global web site:

http://www.yamahaproaudio.com/

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

Transcripción de documentos

DIGITAL MIXING ENGINE Owner’s Manual EN Explanation of Graphical Symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. The above warning is located on the top of the unit. IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. 11 Only use attachments/accessories specified by the manufacturer. 12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 13 Unplug this apparatus during lightning storms or when unused for long periods of time. 14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. ADVARSEL! IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT. The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or colored GREEN or GREEN-and-YELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. • This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd. (class B) (3 wires) Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. VARNING Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. VAROITUS Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. (lithium caution) This product contains a battery that contains perchlorate material. Perchlorate Material—special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate. • This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (Perchlorate) COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) NEDERLAND / THE NETHERLANDS • Dit apparaat bevat een lithium batterij voor geheugen back-up. • This apparatus contains a lithium battery for memory back-up. • Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het apparaat ann het einde van de levensduur of gelieve dan contact op te nemen met de vertegenwoordiging van Yamaha in uw land. • For the removal of the battery at the moment of the disposal at the end of life please consult your retailer or Yamaha representative office in your country. • Gooi de batterij niet weg, maar lever hem in als KCA. • Do not throw away the battery. Instead, hand it in as small chemical waste. (lithium disposal) In Finland: Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan. In Norway: Apparatet må tilkoples jordet stikkontakt. In Sweden: Apparaten skall anslutas till jordat uttag. (class I hokuo) Responsible Party : Yamaha Corporation of America Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620 Telephone : 714-522-9011 Type of Equipment : Digital Mixing Engine Model Name : DME64N / DME24N This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (FCC DoC) PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply/Power cord Water warning • Only use the voltage specified as correct for the device. The required voltage is printed on the name plate of the device. • Use only the supplied power cord/plug. • Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it. • Do not expose the device to rain, use it near water or in damp or wet conditions,or place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings. If any liquid such as water seeps into the device, turn off the power immediately and unplug the power cord from the AC outlet. Then have the device inspected by qualified Yamaha service personnel. • Never insert or remove an electric plug with wet hands. • Be sure to connect to an appropriate outlet with a protective grounding connection. Improper grounding can result in electrical shock. Fire warning • Check the electric plug periodically and remove any dirt or dust which may have accumulated on it. • Do not put burning items, such as candles, on the unit. A burning item may fall over and cause a fire. Do not open If you notice any abnormality • The device contains no user-serviceable parts. Do not open the device or attempt to disassemble the internal parts or modify them in any way. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel. • When one of the following problems occur, immediately turn off the power switch and disconnect the electric plug from the outlet. Then have the device inspected by Yamaha service personnel. • The power cord or plug becomes frayed or damaged. • It emits unusual smells or smoke. • Some object has been dropped into the instrument. • There is a sudden loss of sound during use of the device. • If this device should be dropped or damaged, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel. CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: Power supply/Power cord • Remove the electric plug from the outlet when the device is not to be used for extended periods of time, or during electrical storms. • Do not place the device in an unstable position where it might accidentally fall over. • When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it. • Do not block the vents. This device has ventilation holes at the front and rear to prevent the internal temperature from rising too high. In particular, do not place the device on its side or upside down, or place it in any poorly-ventilated location, such as a bookcase or closet. Location • Do not place the device in a location where it may come into contact with corrosive gases or salt air. Doing so may result in malfunction. • Before moving the device, remove all connected cables. • When setting up the device, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. 4 DME64N/DME24N Owner’s Manual (5)-1 Connections • Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. 1/2 Maintenance Backup battery • Remove the power plug from the AC outlet when cleaning the device. Handling caution • Do not insert your fingers or hand in any gaps or openings on the device (vents, ports, etc.). • Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any gaps or openings on the device (vents, ports, etc.) If this happens, turn off the power immediately and unplug the power cord from the AC outlet. Then have the device inspected by qualified Yamaha service personnel. • Do not use the device or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. • Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on the buttons, switches or connectors. This device has a built-in backup battery that maintains data in internal memory even when the device’s power is switched off. The backup battery will eventually become depleted, however, and when that happens the contents of the internal memory will be lost.* To prevent loss of data be sure to replace the backup battery before it becomes fully depleted. When the remaining capacity of the backup battery becomes so low that it needs to be replaced a “Low Battery” or “No Battery” message will appear on the display during operation or when the device is powered on. If either of these messages appears do not turn off the power and immediately transfer any data you want to save to a computer or other external storage device, then have qualified Yamaha service personnel replace the backup battery. The average life of the internal backup battery is approximately 5 years, depending on operating conditions. * Data items maintained in the internal memory by the backup battery are as follows: • Current scene parameters and number. • Device parameters (SLOT, HA, UTILITY, Master Mute/Level, etc.). • Event log. Data items other than those described above are stored in memory that does not require backup power, and will be retained even if the backup battery fails. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed. Do not turn the [POWER] switch on and off repeatedly and rapidly. Be sure to wait six seconds or more between turning the power to the unit off and then on. Always turn the power off when the device is not in use. The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualified Yamaha service personnel about replacing defective components. NOTICE To avoid the possibility of damage to the product, data or other property, follow the notices below.  Handling and Maintenance • Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the device, TV, or radio may generate noise. • Condensation can occur in the device due to rapid, drastic changes in ambient temperature-when the device is moved from one location to another, or air conditioning is turned on or off, for example. Using the device while condensation is present can cause damage. If there is reason to believe that condensation might have occurred, leave the device for several hours without turning on the power until the condensation has completely dried out. • Do not expose the device to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components. • Avoid setting all equalizer controls and faders to their maximum. Depending on the condition of the connected devices, doing so may cause feedback and may damage the speakers. Information  About this manual • The illustrations in this document are for instructional purposes, and may appear somewhat different from the actual equipment. • The bitmap fonts used in this device have been provided by and are the property of Ricoh Co., Ltd. • Ethernet is a trademark of Xerox Corporation. • All other trademarks are the property of their respective holders and are hereby acknowledged. • CobraNet and Peak Audio are trademarks of Cirrus Logic, Inc. (5)-1 2/2 DME64N/DME24N Owner’s Manual 5 Foreword Foreword Thank you for choosing a Yamaha DME64N/24N Digital Mixing Engine. Using the supplied DME Designer software, the DME64N and DME24N can be easily configured to handle a wide range of audio processing applications – institutional audio installations, sub-mixing, speaker system control, matrix and routing, multi-effect processing, and much more. In order to take full advantage of the features and performance provided by the DME64N/24N, we urge you to read this owner’s manual thoroughly before use, and keep it in a safe place for future reference. The Yamaha Pro Audio web site is at: http://www.yamahaproaudio.com/ 6 DME64N/DME24N Owner’s Manual Contents Foreword 8 Accessories (Please make sure the following items are included in the package.). . . . . . . . . . . 8 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 About the Product Names . . . . . . . . . . . . . . . . . . 8 About the Firmware Version. . . . . . . . . . . . . . . . . 8 Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Connecting the AC power cord . . . . . . . . . . . . . . . . . . . . . .8 Turning the power on and off . . . . . . . . . . . . . . . . . . . . . . .8 Introduction to the DME64N/24N 9 Differences between DME64N/24N . . . . . . . . . . . 9 DME64N/24N Features . . . . . . . . . . . . . . . . . . . . . 9 Audio System Network . . . . . . . . . . . . . . . . . . . . . 9 Glossary for the DME64N/24N . . . . . . . . . . . . . . . 9 Signal Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 System Examples . . . . . . . . . . . . . . . . . . . . . . . . 12 About DME Designer. . . . . . . . . . . . . . . . . . . . . . 13 The Controls and Connectors 14 Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Setup 18 Setup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . 18 I/O Card Installation. . . . . . . . . . . . . . . . . . . . . . . 20 Compatible I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 I/O Card Installation Procedure. . . . . . . . . . . . . . . . . . . . .21 Connecting to a Computer 22 USB Connection . . . . . . . . . . . . . . . . . . . . . . . . . 22 Ethernet Connection ([NETWORK] Connector) . 23 Audio I/O Connection 26 Analog Audio Connection ([IN] and [OUT] Connectors) (DME24N only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 I/O Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Connecting to an External Device Panel Operation and Displays 34 Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . 34 Main Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Parameter Edit Displays. . . . . . . . . . . . . . . . . . . 36 Editing User Defined Button . . . . . . . . . . . . . . . . . . . . . . Mute Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Output Level Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scene Recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scene Store . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spectrum Display . . . . . . . . . . . . . . . . . . . . . . . . Level Meter Display . . . . . . . . . . . . . . . . . . . . . . Initializing the DME64N/DME24N. . . . . . . . . . . . Utility Displays . . . . . . . . . . . . . . . . . . . . . . . . . . 41 42 42 43 Items accessible via the Utility display. . . . . . . . . . . . . . . Utility Display Operation . . . . . . . . . . . . . . . . . . . . . . . . . Info Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network Settings (Net) Page . . . . . . . . . . . . . . . . . . . . . . Display Setup (Disp) Page. . . . . . . . . . . . . . . . . . . . . . . . Security Setup (Lock) Page . . . . . . . . . . . . . . . . . . . . . . . Miscellaneous Setup (Misc) Page . . . . . . . . . . . . . . . . . . Remote Control Setup (Remote) Page . . . . . . . . . . . . . . MIDI Setup (MIDI) Page . . . . . . . . . . . . . . . . . . . . . . . . . Word Clock Setup (WCLK) Page. . . . . . . . . . . . . . . . . . . Slot Information (Slot) Page. . . . . . . . . . . . . . . . . . . . . . . GPI Setup (GPI) Page . . . . . . . . . . . . . . . . . . . . . . . . . . . Head Amplifier Setup (HA) Page . . . . . . . . . . . . . . . . . . . Cascade Setup (CASCAD) Page . . . . . . . . . . . . . . . . . . Check Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . References 38 39 39 39 40 40 43 45 45 46 46 47 48 48 49 50 51 51 52 53 54 55 Introduction to the DME64N/24N The Controls and Connectors Setup Connecting to a Computer Audio I/O Connection Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 ICP1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 CP4SW, CP4SF, and CP1SF . . . . . . . . . . . . . . . . . . . . . 55 Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . Input/Output Characteristics . . . . . . . . . . . . . . . Control I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connector Pin Assign . . . . . . . . . . . . . . . . . . . . Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MIDI Data Format . . . . . . . . . . . . . . . . . . . . . . . . MIDI Data Format . . . . . . . . . . . . . . . . . . . . . . . . Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 59 60 61 62 63 65 66 70 71 28 Remote Connection ([REMOTE] Connector) . . 28 Foreword Connecting to an External Device Panel Operation and Displays References Index 73 Controlling external head amplifiers from the DME64N/24N .28 Controlling a DME24N’s internal head amps from a digital mixer .29 Controlling the DME64N/24N from an external device . . .29 Network Connection ([NETWORK] Connectors) . 30 MIDI Connection ([MIDI] Connectors) . . . . . . . . 30 Cascade Connection ([Cascade] Connectors) (DME64N only) . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 WORD CLOCK Connection ([WORD CLOCK] Connectors) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 GPI Connection ([GPI] Connectors). . . . . . . . . . 33 DME64N/DME24N Owner’s Manual 7 Accessories (Please make sure the following items are included in the package.) Foreword Thank you for choosing a Yamaha DME64N/24N Digital Mixing Engine. In order to take full advantage of the features and performance provided by the DME64N/24N, we urge you to read this owner’s manual thoroughly before connecting or using the unit. Keep this manual in a safe place for future reference. Foreword Accessories (Please make sure the following items are included in the package.) • • • • • • DME64N/DM24N Owner’s Manual (This document) AC power cord AC plug clamp Euroblock plug (16P) x 2 Euroblock plug (8P) x 4 (DME64N only) Euroblock plug (3P) x 16 (DME24N only) Options Preparation Connecting the AC power cord CAUTION First plug the female-connector end of the AC cord into the [AC IN] socket on the rear panel of the DME64N/ 24N, then plug the male plug into an appropriate AC mains outlet. Be sure to use the voltage specified for the device. Turning the power on and off Control Panels • • • • ICP1 Intelligent Control Panel CP4SW Control Panel CP4SF Control Panel CP1SF Control Panel CAUTION NOTE For more information on your Control Panel, refer to the owner’s manual that came with the Control Panel, as well as the DME Designer Owner’s Manual. About the Product Names Be sure to turn all devices OFF before connecting AC mains power. To prevent the initial power-on surge from generating a large noise spike or damaging your speaker system, turn the devices on in the following order: audio sources, mixer (such as M7CL or PM5D), DME64N/24N, and finally power amplifiers. Reverse this order when turning power off. 1. Press the [POWER] switch to turn on the power to the DME64N/24N. 2. Press the [POWER] switch again to turn off the power. NOTE In this manual, models DME64N, DME24N, DME8i-C, DME8o-C, DME4io-C, DME8i-ES, DME8o-ES and DME4io-ES are categorized as DME series, and models DME8i-C, DME8o-C, DME4io-C, DME8i-ES, DME8o-ES and DME4io-ES are all called the “DME Satellite”. About the Firmware Version The DME64N/24N remembers scene settings when you turn off the power. When you turn on the power to the DME64N/24N, it will start up with the same scene settings. You can set up the DME64N/24N so that at the startup it will recall the scene selected before you turned off the power to the device. (page 48) You can download the latest firmware from the following Yamaha website. http://www.yamahaproaudio.com/downloads/ CAUTION CAUTION 8 DME64N/DME24N Owner’s Manual Do NOT turn off the power to the DME64N/24N while it is receiving data from DME Designer or while it is being manipulated from an external device. Otherwise, a malfunction may occur. Even when the power switch is turned off, electricity is still flowing to the product all the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. Differences between DME64N/24N Introduction to the DME64N/24N Differences between DME64N/24N The DME64N has four I/O card slots, while the DME24N has one I/O card slot and eight channels of builtin analog audio I/O. A single I/O card can handle up to 16 channels of audio I/O, so the DME64N can handle a maximum of 64 audio I/O channels. The DME24N can handle up to 24 audio I/O channels. The DME64N has approximately double the DSP processing power of the DME24N. DME64N/24N Features Introduction to the DME64N/24N In addition to basic mixing and matrix output functions, the DME64N/24N includes a equalizers, compressors, delay, etc. – that can be patched together via DME Designer to configure just about any audio system you need. Audio System Network Multiple DME series units that are interconnected in a network via Ethernet function as a single audio system. In a DME audio system, a group of the same models that can be operated in sync is called a “device group;” audio processing divisions that accommodate multiple device groups are called “zones;” and the entire area serviced by the acoustic system is called an “area.” Each device group always includes one DME series unit that functions as the “group master” and controls all other DME series units in the same device group. If a computer is connected to the network, you can use the computer to control an entire device group via the group master. Glossary for the DME64N/24N This section explains terminology specific to the DME64N/24N. Components and parameters The individual audio processing modules (equalizers, compressors, etc.) are called “components.” External head amplifier control modules are also available as components. Changing the parameters of components enables control over the operation of the components. Configuration A “configuration” is a complete set of components for constructing an audio system. Each configuration determines the audio function(s) of the corresponding DME64N/24N unit. All parameter sets included with each component in a configuration are called “preset parameters.” One DME64N/24N unit has a number of configurations, and a configuration has a number of preset parameters. User Defined buttons Assigning parameters to be User Defined Buttons enables you to control the device from the ICP1 and the DME64N/DME24N. Refer to the DME Designer Owner’s Manual for details. DME64N/DME24N Owner’s Manual 9 Glossary for the DME64N/24N Scene A combination of all configuration and preset parameters is called a “scene.” Scenes can be recalled from an ICP1, GPI device, other external controllers, DME64N/DME24N, or computer. Up to 999 scenes can be stored for each device group. Scene structure Scene Preset Parameter Configuration Matrix Mixer Scene 1 Ex.: Gate • Attack • Decay • Range • Threshold • Key in • Hold Scene 2 16 x 8 Scene 999 Component Introduction to the DME64N/24N Scene change First Act Band Set Play Set Stage 1 EXT. CLOCK NETWORK 96kHz MID 88.2kHz MASTER 48kHz 2 3 4 2 3 4 5 6 7 8 5 6 7 8 Dark Change Band Set Play Set Play Set 1 Band Set Stage Stage 1 PEAK IN SIGNAL Second Act EXT. CLOCK NETWORK 96kHz MID 88.2kHz MASTER 48kHz 44.1kHz 2 3 4 2 3 4 5 6 7 8 5 6 7 8 PEAK IN SIGNAL 1 44.1kHz PEAK PEAK SCENE NUMBER SIGNAL SCENE NUMBER OUT SIGNAL Scene 1 10 DME64N/DME24N Owner’s Manual Scene Recall OUT Scene 2 Signal Types Signal Types DME64N/24N audio system signals can be broadly categorized as follows. 1 Audio The DME64N/24N will be required to send and receive audio signals to and from other DME series units as well as other audio equipment. Audio signal transmission and reception will occur primarily via the [INPUT] and [OUTPUT] connectors on the DME24N. 2 Control signals within a device group Introduction to the DME64N/24N Device group control signals control all DME series devices in the group. There are two types of device group control signals, as follows: • Control signals between the computer and the group master DME series unit • Control signals between the group master DME series unit and the other DME series units You can use the DME Designer application to control the entire device group, such as sending components to the devices and setting the parameters as required. 3 Control signals between devices outside the device group These signals provide communication and control between individual devices. Included in this category are MIDI messages transferred between [USB] connectors, GPI signals transferred between [GPI] connectors, and remote head amp control signals handled via the [REMOTE] connector. Type of signals handled by the DME64N/24N Audio Signal Device Control Word Clock Reference Page [USB] Connector – • Control signals between computer and DNE64N/24N • MIDI messages – 22 [NETWORK] Connector – • Control signals between computer and DNE64N/24N • Control signals between DME series unit. • Control signals with a controller such as an AMX or Crestron – 23 [MIDI] Connector – Control signals (MIDI commands) between MIDI controller and DME64N/ 24N. – 30 [GPI] Connector – Control signals between GPI device (GPI controller, etc.) and DME series unit – 33 Connector [CASCADE] Connector (DME64N only) 32 channels of input/output. Control signals from the digital mixer to the DME64N Word clock transmission and reception to and from other devices. 31 Word clock transmission and reception to and from other devices. 32 [WORD CLOCK] Connector – – [REMOTE] Connector – • Control signals to/from an external device (such as AD8HR head amplifier) • Control signals for a digital mixer and internal head amp • Control signals with a controller such as an AMX or Crestron • MIDI messages – 28 – – 26 Word clock transmission and reception to and from other devices (depending on function of card). 27 (Audio I/O Connectors) (DME24N only) 8 channels of input and output. (I/O Slot) Number of I/O Serial signal transmission/reception channels depends (depending on function of card). on card. DME64N/DME24N Owner’s Manual 11 System Examples System Examples Large systems using CobraNet Space A Space B Computer ICP1 DME24N 1 Network Switch EXT. CLOCK NETWORK 96kHz MID 88.2kHz MASTER 48kHz 2 3 4 2 3 4 5 6 7 8 5 6 7 8 Analog Out Analog In PEAK IN SIGNAL 1 44.1kHz PEAK SCENE NUMBER OUT SIGNAL MY16-CII Network Switch DME24N 1 EXT. CLOCK NETWORK 96kHz MID 88.2kHz MASTER 48kHz 2 3 4 2 3 4 5 6 7 8 5 6 7 8 PEAK 1 Analog Out Analog In IN SIGNAL 44.1kHz PEAK SCENE NUMBER SIGNAL OUT Introduction to the DME64N/24N Network Switch DME64N MY16-CII SCENE HOME UTILITY LEVEL MUTE CANCEL ENTER MY16-CII x 4 Space C DME8i-C INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT Analog In Network Switch DME8i-C Network Switch INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT Analog In DME8i-C INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT Network Switch Analog In DME8i-C INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT Analog In Ethernet CobraNet Ethernet Network Switch Space D DME8o-C Analog Out DME8o-C Analog Out DME8o-C Analog Out DME8o-C Analog Out CobraNet Network Switch Network Switch Network Switch 12 DME64N/DME24N Owner’s Manual About DME Designer About DME Designer DME64N/DME24N Owner’s Manual Introduction to the DME64N/24N DME Designer software enables you to integrate, configure, and control the DME series system from a connected computer. You can build the DME series audio system using graphic blocks in DME Designer that are displayed on the computer monitor. The DME series settings, configuration, and parameter data are transferred from the computer to the DME series unit via the USB or Ethernet connection. DME series settings, configuration, and parameter data is sent via USB or Ethernet to the connected DME series unit. After the data is transmitted, you can disconnect the DME series unit from the computer and use it as an independent processor. You can also connect it to a computer and control it in realtime from DME Designer. If multiple DME series units are connected in the network, DME Designer enables you to build a configuration that includes those units. Please download the DME Designer application, driver, DME setup manual, and DME Designer Owner’s Manual at the following URL: http://www.yamahaproaudio.com/ Refer to the “Connecting to a Computer” (page 22) for more information on connecting a computer to the DME64N/24N. For details on how to install DME Designer and the drivers that are required for connection, refer to the “DME Setup Manual.” Refer to the DME Designer Owner’s Manual for setup and operation instructions. 13 Front Panel The Controls and Connectors Front Panel DME64N ! @ SCENE 1 # HOME 2 ^ ) 9 $ UTILITY * % LEVEL A B C ( CANCEL MUTE & D ENTER 4 5 6 3 The Controls and Connectors DME24N ^ ) 9 & A 1 ! @ SCENE 2 3 4 5 6 # HOME $ UTILITY % LEVEL * MUTE C ( CANCEL B D ENTER 7 8 7 8 1 [USB] Connector A computer can be connected here when it is necessary to program or control the device. When a USB connection is to be used, the USB-MIDI driver must be installed on the computer. Refer to the DME Designer Installation Guide for installation instructions. 2 [EXT. CLOCK] Indicator When a clock signal from an external device is selected, the indicator will light green. If the clock signal is not appropriate the indicator will flash red. The indicator will go out when the internal word clock is selected. 3 [96kHz] [88.2kHz] [48kHz] [44.1kHz] Indicator Normally, the indicator corresponding to the current word clock frequency will light green. If a problem with the master clock is detected all of these indicators will flash red. 2 seconds after a problem is detected with an external master clock the internal clock will temporarily be selected. When this happens the indicator corresponding to the frequency of the internal clock will light green, and all other indicators will continue to flash red. 4 [NETWORK] Indicator Lights while data communication is occurring via the [USB], [NETWORK], or [CASCADE] connector. Received data causes the indicator to light in green, while transmitted data causes the indicator to light in orange. If a problem occurs the indicator will light in red. 14 DME64N/DME24N Owner’s Manual Front Panel 5 [MIDI] Indicator % [MUTE] Button Lights while data communication is occurring via the [MIDI] connector. Received data causes the indicator to light green, while transmitted data causes the indicator to light orange. The indicator will light green when reception and transmission occur simultaneously. If a problem occurs the indicator will light red. Calls the mute display (page 39). The indicator will light orange when mute is on. The indicator will light green when mute is off and the mute display is showing, and will be off if the mute display is not showing. ^ Dial Adjusts the value of selected parameters. 6 [MASTER] Indicator 7 [PEAK] Indicator (DME24N only) Light red when a signal on the corresponding built-in analog audio input or output ([IN] and [OUT] connectors) reaches or exceeds -3 dB. 8 [SIGNAL] Indicator (DME24N only) Light green when a signal with a level greater than -40 dB is present at the built-in analog audio inputs and outputs ([IN] and [OUT] connectors). NOTE The DME64N has no built-in analog audio inputs or outputs ([IN] and [OUT] connectors). & [ E ] [  ] [  ] [ F ] Buttons Move the display cursor in the corresponding directions. * [CANCEL] Button Closes the window on the display. ( [ENTER] Button Confirms and enters a value or setting. A [PHONES] Jack A pair of headphones can be plugged in here. The Controls and Connectors Lights green when the device is operating as the device group master (page 9). The indicator will not light if the device is operating as a device group slave. Refer to page 45 for device group master setup instructions. B [PHONES LEVEL] Control Adjusts the headphone volume. Even when the control is set to the minimum level, the sound at the headphones is not completely muted. C [MONITOR] Button 9 [SCENE NUMBER] Indicator Shows the current scene number. ) Display Displays scene information and device parameters. ! [SCENE] Button Calls the scene recall/store display (page 39). The scene store display will appear if the button is held for longer than 2 seconds (page 40). The indicator will light green while the scene recall or store display is showing. Calls the monitoring point slot selection display (page 40). When the [ENTER] button is pressed to select a slot, the monitoring point selection display will appear. The spectrum analyzer display will then appear when the [ENTER] button is pressed to select a monitoring point. The indicator will light green while the monitoring slot/ point or spectrum analyzer display is showing. D [POWER] Switch Turns mains power to the device on and off. CAUTION @ [HOME] Button Directly recalls the home (main) display. If pressed while the main display is showing the [HOME] button steps through the user-defined parameter display pages (refer to page 38 in this manual). Even when the power switch is turned off, electricity is still flowing to the product all the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. # [UTILITY] Button Calls the output level display. If this button is held for longer than 2 seconds while the main display is showing the utility display will appear. Switches between the Utility display pages if pressed while the Utility display is showing. $ [LEVEL] Button Calls the output level setup display (page 39). The indicator will light green. DME64N/DME24N Owner’s Manual 15 Rear Panel Rear Panel 4 DME64N 1 2 6 7 3 DME24N The Controls and Connectors 1 2 5 ) 9 3 4 9 6 7 5 8 1 [AC IN] Connector 3 [GPI] Connector This is the device’s three-pronged AC power connector. Connect to the AC mains using the supplied AC power cord. See “Setup” on page 18 for details. This Euroblock connector provides access to the unit’s GPI (General Purpose Interface) interface for transfer of control signals to and from external equipment. The DME64N provides 16 channels of GPI input and output, while the DME24N provides 8 channels. Each input channel has an IN terminal and a +V terminal. Output channels each have an OUT terminal and a GND terminal. The open voltage at the +V terminal is 5V, while the IN terminal detects voltage changes from 0V ~ 5V. The OUT terminals output either signal “L” or “H” at a TTL level. See “GPI Connection ([GPI] Connectors)” on page 33 for connection details. NOTE Use the supplied AC cord clamp to prevent accidental disconnection of the AC power. CAUTION Even when the power switch is turned off, electricity is still flowing to the product all the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. 2 Ground Screw The supplied AC power cable is a 3-wire type, so if the AC outlet used is properly earthed the DME64N/24N will be earthed as well. Hum and interference may by further reduced in some cases by also connecting the earth screw to an earth point. NOTE Connect the device to only one ground point. Connecting the device to more than ground point can result in ground loops that can cause increased hum and noise. 4 [MIDI IN] [MIDI OUT] [MIDI THRU] Connectors These are standard MIDI connectors that handle reception and transmission of MIDI data: [MIDI IN] receives MIDI data, [MIDI OUT] transmits MIDI data, and [MIDI THRU] re-transmits MIDI data received at the [MIDI IN] connector. See “MIDI Connection ([MIDI] Connectors)” on page 30 for connection details. 5 [WORD CLOCK IN] [WORD CLOCK OUT] Connectors These BNC connector receive and transmit word clock from and to external equipment. See “WORD CLOCK Connection ([WORD CLOCK] Connectors)” on page 32 for connection details. Word clock settings are available via the device’s Utility display WCLK page (see page 50 of this document). 16 DME64N/DME24N Owner’s Manual Rear Panel 6 [NETWORK] Connector This is a 100Base-TX/10Base-T Ethernet connector for connection to a computer or other DME series units. Normally this connector will be connected to a network switch via an Ethernet cable. When two DME64N/24N units are to be directly connected a “cross” cable should be used. See “Ethernet Connection ([NETWORK] Connector)” on page 23 for connection details. NOTE Use a STP (Shielded Twisted Pair) cable for this connection to prevent electromagnetic interference. 7 [REMOTE] Connector This 9-pin D-SUB connector allows connection to Yamaha AD824 or AD8HR remote head amplifier or an RS-232C/RS-422 compatible controller such as those from AMX or Crestron. You can also connect a Yamaha PM5D or DM2000 and control the internal head amps of DME24N. Refer to page 28 for connection details. The Controls and Connectors 8 [IN] [OUT] Connectors (DME24N only) These are balanced Euroblock connectors for analog audio input and output. The analog signal from microphones or line sources such as CD players can be input via the IN connectors, while the OUT connectors can deliver analog output to powered speakers or recording equipment. 48V phantom power can be supplied to the IN connectors (page 51). Refer to page 26 for [IN] and [OUT] connection details. NOTE The [IN] and [OUT] connectors each have 24 terminal pins. Each of the eight inputs and outputs uses three pins – hot, cold, and ground. Use the supplied 3-pin Euroblock plugs to connect to the appropriate inputs and outputs. 9 I/O Slots Optional Yamaha or third-party mini-YGDAI cards can be plugged in here for system expansion. The DME64N has four I/O slots, while the DME24N has one. One expansion card can be plugged into each slot. Refer to “I/O Card Installation” on page 20 for installation details. ) [CASCADE IN] [CASCADE OUT] Connectors (DME64N only) This 68-pin D-SUB connector can be connected to the CASCADE connector of other devices via a dedicated cascade cable. The CASCADE connector transmits and receives control, audio, and word clock signals. Refer to “Cascade Connection ([Cascade] Connectors” on page 31 for connection details. DME64N/DME24N Owner’s Manual 17 Setup Procedure Setup Setup Procedure Follow the steps outlined below to prepare the DME64N/24N for operation. 1. Install any required I/O cards. Refer to “I/O Card Installation” on page 20 for details. 2. Connect the AC power cord. CAUTION Be sure to turn all devices OFF before connecting AC mains power. Attach the cable clamp to prevent accidental disconnection. Attaching the cable clamp. Setup Be sure to properly ground the device to prevent possible electrical shock. First plug the female-connector end of the AC cord into the [AC IN] socket on the rear panel of the DME64N/24N, then plug the male plug into an appropriate AC mains outlet. Make sure the AC power to be used complies with the conditions marked on the top cover of the device. CAUTION Use only the AC power cord supplied with the DME64N/24N. If the supplied cord is lost or damaged and needs to be replaced, contact your Yamaha dealer. The use of an inappropriate replacement can pose a fire and shock hazard! The type of AC power cord provided with the DME64N/24N may be different depending on the country in which it is purchased (a third prong may be provided for grounding purposes). Improper connection of the grounding conductor can create the risk of electrical shock. Do NOT modify the plug provided with the DME64N/24N. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use a plug adapter which defeats the grounding conductor. Security Cover Mounting Security cover mounting screw holes (M3 size) are provided on the front panel of the unit. The spacings are 423mm width and 96mm (DME64N) / 52mm (DME24N) height. See “Dimensions” on page 65 for details. A security cover made by the customer or contractor can be attached to the front panel via these mounting holes to prevent accidental operation. Yamaha cannot supply a security cover. When mounting a cover make sure that the screws used do not go deeper than 15 millimeters into the front panel. Also, to ensure that the cover does not come in contact with the panel controls, leave a space of about 20 millimeters between the front panel and the cover. 3. Install the DME Designer software and necessary drivers on the computer to be used for device group control. See the “DME Setup Manual” (PDF file) for details. 18 DME64N/DME24N Owner’s Manual Setup Procedure 4. Connect devices. • Network connection Ethernet connection (page 23) USB connection (page 22) • Analog connection (page 26) • External device connection Remote connection (page 28) MIDI connection(page 30) CASCADE connection(page 31) WORD CLOCK connection(page 32) GPI connection (page 33) 5. Turn power to the computer, DME64N/24N, and related devices on. Press the DME64N/24N [POWER] switch to turn it on. CAUTION To prevent the initial power-on surge from generating a large noise spike or damaging your speaker system, turn devices on in the following order: audio sources, mixer and/or recorders, and finally power amplifiers. Reverse this order when turning power off. Setup No information will appear on the display the first time the device is turned on. The appropriate scene and other data must first be transferred to the device from the DME Designer. Refer to the “DME Setup Manual” (PDF file) for details. Once the appropriate data has been transferred to the device, the current number and name will appear on the display: If any scene data has been stored in the DME64N/24N, the current scene and its name will be displayed. 6. Set up the DME64N/24N operation parameters. See the “Utility Display” section on page 43 for details. NOTE The “NET” page settings must be set up as required before using the unit for the first time. 7. Launch the DME Designer application, create configuration and transfer. DME Designer setup, operation, and data transfer instructions can be found in the DME Designer Manual. This completes preparation of the DME64N/24N system. DME64N/DME24N Owner’s Manual 19 I/O Card Installation I/O Card Installation The DME64N has four I/O card slots, and the DME24N has one I/O card slot. The number of audio input channels available on the DME64N/24N can be increased by plugging the appropriate mini-YGDAI I/O card(s) into the available card slot(s). Compatible I/O Cards As of June, 2010, Yamaha mini-YGDAI cards that can be used with the DME64N/24N are as follows: Card Name Function Input Output No. of Available Cards DME64N DME24N MY8-AT ADAT 8 8 4 1 MY8-TD TDIF-1 8 8 4 1 MY8-AE AES/EBU 8 8 4 1 MY4-AD ANALOG IN 4 – 4 1 MY8-AD ANALOG IN 8 – 4 1 MY4-DA ANALOG OUT – 4 4 1 MY8-AD24 ANALOG IN 8 – 4 1 MY8-AD96 ANALOG IN 8 – 4 1 MY8-DA96 ANALOG OUT – 8 4 1 MY8-ADDA96 ANALOG IN/OUT 8 8 4 1 MY8-AE96S AES/EBU 8 8 4 1 MY8-AE96 AES/EBU 8 8 4 1 Setup MY8-AEB AES/EBU 8 8 4 1 MY16-AT ADAT 16 16 4 1 1 MY16-AE AES/EBU 16 16 4 MY16-TD TDIF-1 16 16 4 1 MY16-C CobraNet 16 16 4(*) 1 MY16-CII CobraNet 16 16 4 1 MY16-ES64 EtherSound 16 16 1 1 MY16-MD64 MADI 16 16 4 1 MY16-EX Expansion 16 16 3 1 MY8-SDI-D HD-SDI 8 – 4 1 The input/output numbers above apply to 44.1/48kHz operation. (*) In order to use three or four MY16-C cards, firmware V1.10 or later will be required. If the serial number written on the upper surface of your DME64N is shown below, a hardware upgrade is needed. KK, KL, KM, KN, KO, KP, KX, KY are the third and fourth digits of the serial number. A fee is charged for the hardware upgrade. For details, contact Yamaha customer support using the contact information located at the end of the “DME64N/24N Owner’s Manual.” For the latest information on what cards can be used with the DME64N/24N, visit the Yamaha Pro Audio website at: http://www.yamahaproaudio.com/ 20 DME64N/DME24N Owner’s Manual I/O Card Installation I/O Card Installation Procedure 1. Make sure that the DME64N/24N power is OFF. If the power is on, turn it off. 2. Loosen the two card slot screws and remove the slot cover, as shown in the diagram. NOTE 3. Setup The slot cover and screws will need to be re-attached if the I/O card is later removed from the slot, so keep them in a safe place. Slide the I/O card into the slots in the guide rails, as shown in the diagram, and push the card into the slot. Be sure to push the card all the way back into the slot so that the card contacts make proper contact with the slot connector. Guide Rail 4. Secure the card with the attached screws. CAUTION Be sure to tighten the screws securely. If the screws are left loose proper contact may be lost and malfunction of damage may result. DME64N/DME24N Owner’s Manual 21 USB Connection Connecting to a Computer USB Connection NOTE • Refer to the “DME Setup Manual” (PDF file) for details on installing USB-MIDI Driver and DME Designer. • Make sure that the USB-MIDI Driver’s THRU setting is “OFF.” USB connections can be used in the following two ways: (1) Control the DME64N/24N from DME Designer. (2) Connect to any individual DME64N/24N and control that DME64N/24N unit by transmitting MIDI commands from a MIDI sequencer or similar software. NOTE • The computer on which DME Designer is running can be connected to either the group master or a slave DME series unit. • The correspondence between the MIDI commands to be received/transmitted and the scene parameters can be set up using DME Designer. • The USB port being used by DME Designer is not available for use by a MIDI sequencer or other application. USB Cable Device Group INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite Connecting to a Computer Ethernet Cable Computer (Running DME Designer.) Network Switch Ethernet Cable Ethernet Cable DME64N/24N INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite SCENE HOME UTILITY LEVEL MUTE CANCEL ENTER USB Cable Computer (Running MIDI Sequencer or similar application.) Be sure to follow the procedure below when you make a USB connection with a computer. Otherwise, the computer and/or DME64N/24N may freeze, resulting in damages or loss of data. If the computer or DME64N/24N freezes, turn the power to the DME64N/24N off and then on, then restart the computer. CAUTION 22 • Before you connect the DME64N/24N to the computer via USB, cancel the computer’s energy saving mode (such as Suspend, Sleep, or Stand-by mode). • Before turning on the power to the DME64N/24N, first connect its [USB] connector to the computer’s USB port. • Before turning the power to the unit on or off, and before connecting or disconnecting the USB cable, take the following actions: - Quit all open applications. - Make sure that the DME64N/24N is NOT transferring any data. • Be sure to wait six seconds or more between turning the power to the unit on and then off (or off and then on), or between connecting and disconnecting (or vice versa) the USB cable. DME64N/DME24N Owner’s Manual Ethernet Connection ([NETWORK] Connector) Ethernet Connection ([NETWORK] Connector) To control the DME64N/24N from the computer via Ethernet, use an Ethernet cable to connect the [NETWORK] connector on the rear panel of the DME64N/24N to the computer, then install DME-N Network Driver. NOTE • Refer to the “DME Setup Manual” (PDF file) for details on installing DME-N Network Driver. • Appropriate IP addresses must first be assigned to all devices connected to an Ethernet network. Two DME series units directly connected via Ethernet SCENE HOME UTILITY LEVEL MUTE CANCEL ENTER DME64N/24N Ethernet Cable INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite USB Cable DME64N/DME24N Owner’s Manual Connecting to a Computer You can connect devices in the same device group directly to each other using Ethernet cables, without connecting them to a network switch. A cross cable or straight cable can be used since the DME series supports Auto MDI/MDI-X. In this case, set Link Mode on both units to the same setting. Devices in different subnet (different network address) groups can be connected via a router or layer-3 compliant network switch. 23 Ethernet Connection ([NETWORK] Connector) Control from a computer in the same subnet group Device Group Group Master INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite (IP address: 192.168.0.7) Ethernet Cable Ethernet Cable Network Switch Ethernet Cable Computer (IP address: 192.168.0.100) Ethernet Cable INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite (IP address: 192.168.0.3) (Master ID: 7) SCENE HOME UTILITY LEVEL MUTE CANCEL ENTER DME64N/24N (IP address: 192.168.0.250) (Master ID: 7) NOTE Connecting to a Computer • The IP addresses in the diagram are examples. • Use a network switch that is compatible with 100Base-TX/10Base-T network speeds. The maximum length of a cable between a network switch and the DME series is 100 meters. Due to the quality of cables and network switch performance, however, proper operation at the maximum length cannot be guaranteed in some cases. Use a STP (Shielded Twisted Pair) cable to prevent electromagnetic interference. • If you are using multiple DME series units, set Link Mode on each unit to the same setting. Yamaha recommends that you select 100Base-TX for the Link Mode setting. Control from a computer with a different subnet Device Group Port settings Destination network address: 192.168.0.0 Subnet mask: 255.255.255.0 Gateway: 192.168.0.254 Group Master INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite (IP address: 192.168.0.5) Ethernet Cable Network Switch Ethernet Cable Ethernet Cable Ethernet Cable PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite (IP address: 192.168.0.3) (Master ID: 5) SCENE HOME UTILITY LEVEL MUTE CANCEL ENTER DME64N/24N (IP address: 192.168.0.12) (Master ID: 5) 24 DME64N/DME24N Owner’s Manual Ethernet Cable Computer INPUT USB Router or Layer-3 Compliant Network Switch Ethernet Connection ([NETWORK] Connector) Connecting multiple device groups Device Group 1 Device Group 2 Group Master Group Master INPUT USB INPUT PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL SIGNAL SIGNAL SIGNAL INPUT DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite (IP address: 192.168.0.2) Ethernet Cable DME Satellite (IP address: 192.168.0.3) Ethernet Cable Network Switch Network Switch Ethernet Cable Ethernet Cable Ethernet Cable Ethernet Cable SCENE HOME UTILITY LEVEL MUTE CANCEL ENTER SCENE DME64N/24N (IP address: 192.168.0.100) (Master ID: 2) Ethernet Cable HOME LEVEL MUTE CANCEL ENTER DME64N/24N (IP address: 192.168.0.200) (Master ID: 3) INPUT INPUT PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL SIGNAL SIGNAL SIGNAL INPUT DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite (IP address: 192.168.0.40) (Master ID: 2) DME Satellite (IP address: 192.168.0.10) (Master ID: 3) Connecting to a Computer USB UTILITY Computer (IP address: 192.168.0.1) DME64N/DME24N Owner’s Manual 25 Analog Audio Connection ([IN] and [OUT] Connectors) Audio I/O Connection Analog Audio Connection ([IN] and [OUT] Connectors) (DME24N only) The DME24N includes [IN] and [OUT] connectors for 8 channels of analog audio input and output. Wire the supplied Euroblock plugs as shown below. Head amplifier gain and phantom power settings can be made via the Utility display HA page described on page 52 of this manual, or via the DME Designer application. Euroblock Connection Please be sure to use the supplied Euroblock plugs. If you lose them, contact your nearest Yamaha dealer. Cable preparation • To prepare the cable for attachment to a Euroblock connector, strip the wire as shown in the illustration, and use stranded wire to make connections. With a Euroblock connection, the stranded wire may be prone to breakage because of metal fatigue due to the weight of the cable or due to vibration. When rack-mounting your equipment, use a lacing bar when possible to bundle and fasten the cables. • If cables will be frequently connected and disconnected, as in the case of a portable installation, we recommend that you use ferrules with insulation sleeves. Use a ferrule whose conductor portion has an external diameter of 1.6 mm or less, and a length of approximately 7 mm (such as the AI0,5-6WH made by the Phoenix Contact corporation). approx. 7 mm 1.6 mm or less If you use stranded wire, do not tin (plate with solder) the exposed end. CAUTION 1. Loosen terminal screws. Loosen. Audio I/O Connection Slotted Screwdriver Terminal Screw Euroblock Plug NOTE A slotted screwdriver with a blade width of about 3 millimeters is recommended. 2. 26 Insert cables. DME64N/DME24N Owner’s Manual 3 mm approx. 7 mm I/O Slots 3. Securely tighten terminal screws. Pull the cables (not too strongly) to confirm that they are securely connected. 4. Plug the Euroblock plug into the panel connector. I/O Slots Audio I/O Connection The DME64N has four I/O card slots, and the DME24N has one I/O card slot. The number of audio input channels available on the DME64N/24N can be increased by plugging the appropriate mini-YGDAI I/O card(s) into the available card slot(s). Some types of cards also provide control and/or word clock transmission and reception functionality. Refer to “Compatible I/O cards” (page 20) for details on the cards that can be used. For details on how to install cards, refer to “I/O card Installation Procedure” (page 21). DME64N/DME24N Owner’s Manual 27 Remote Connection ([REMOTE] Connector) Connecting to an External Device Remote Connection ([REMOTE] Connector) The [REMOTE] connector of the DME64N/24N can be connected to remotely-controllable Yamaha AD8HR or AD824 head amplifiers (pre-amps), digital mixers, or RS-232C compatible controllers (such as those from AMX or Crestron). The [REMOTE] connector also transmits and receives MIDI messages. Controlling external head amplifiers from the DME64N/24N You can remotely control the AD8HR or AD824 head amplifier settings from DME Designer. Up to eight AD8HR/AD824 head amplifiers can be connected. When connecting to a combination of AD8HR and AD824 head amplifiers, be sure to place the AD8HR units closest to the DME64N/24N in the chain, otherwise the AD8HR or AD824 unit(s) may not be properly recognized by the DME64N/24N. For details about the settings, refer to the “Ext HA Ctrl” in “Remote page” on page 49. D-SUB 9-pin Cable (Interlink Crossover) Set to Remote (422) REMOTE HA REMOTE 1 HA REMOTE 2 HA REMOTE 1 HA REMOTE 2 DME64N/24N AD8HR COM PC/RS-422 AD824 AD8HR COM RS-422 COM PC/RS-422 AD824 COM RS-422 COM PC/RS-422 AD824 NOTE Connecting to an External Device Only control signals are transmitted and received via the REMOTE connection. Audio connections must be made separately. 28 DME64N/DME24N Owner’s Manual Remote Connection ([REMOTE] Connector) Controlling a DME24N’s internal head amps from a digital mixer The internal head amp settings of a DME24N can be remotely controlled from a digital mixer such as the Yamaha PM5D or DM2000. Connect the digital mixer to the DME series’ [REMOTE] connector, and use an Ethernet cable to make connections between the [NETWORK] connectors of the DME series. From the digital mixer, DME series units can be controlled as an AD8HR. The gain and the phantom power (+48V) can be controlled. For details about the settings, refer to the “Int HA Ctrl” in “Remote page” on page 49. D-SUB 9-pin Cable REMOTE REMOTE Ethernet Cable 1 EXT. CLOCK NETWORK 96kHz MID 88.2kHz MASTER 48kHz 2 3 4 2 3 4 5 6 7 8 5 6 7 8 PEAK IN SIGNAL 1 44.1kHz PEAK SCENE NUMBER OUT SIGNAL DME64N/24N 1 EXT. CLOCK NETWORK 96kHz MID 88.2kHz MASTER 48kHz 2 3 4 2 3 4 5 6 7 8 5 6 7 8 Network Switch PEAK IN SIGNAL 1 44.1kHz PEAK SCENE NUMBER SIGNAL OUT DME64N/24N Digital Mixer NOTE Only one mixer can be connected within each device group. The digital mixer can be connected to any DME series unit, whether it is the group master or a slave unit. The ID number of the DME series unit being remotely controlled is specified from DME Designer. For details on making this setting, refer to the “DME Designer Owner’s Manual.” If the connection between DME series units is broken, it will no longer be possible to communicate with DME units of an ID number that follows the disconnected DME. The variable range of GAIN differs between the AD8HR and the DME24N. You cannot use the mixer to specify a value that exceeds the variable range of the DME24N. Connecting to an External Device Controlling the DME64N/24N from an external device You can remotely control the DME64N/24N from a connected RS-232C or RS-422 compatible controller, such as those from AMX or Crestron. When connecting a remote controller via RS-232C or RS-422, be sure to set the “Utility” display “Remote page” (see manual page 45) “Rmt Ctrl” parameter to match the controller being connected. Also, do change this setting while the unit is connected. Doing so can damage the unit. NOTE Refer to “DME Remote Control Protocol Specifications” on the Yamaha web site for more information on communication protocols used to control the DME64N/24N from an external device (such as those from AMX or Crestron). http://www.yamahaproaudio.com/ DME64N/24N Owner’s Manual 29 Network Connection ([NETWORK] Connectors) Network Connection ([NETWORK] Connectors) You can connect a controller such as the AMX or Crestron to DME64N/24N via Ethernet, and remotely control multiple DME64N/24N units. For details about the settings, refer to the "Rmt Ctrl" in "Remote page" on page 48. • The port used for remote control is specified from DME Designer. For details on making this setting, refer to the “DME Designer Owner’s Manual.” • Refer to “DME Remote Control Protocol Specifications” on the Yamaha web site for more information on communication protocols used to control the DME64N/24N from an external device (such as those from AMX or Crestron). http://www.yamahaproaudio.com/ MIDI Connection ([MIDI] Connectors) In this case connection is made to the rear-panel [MIDI] connectors. MIDI commands are sent to the DME64N/24N from a MIDI device. Refer to “MIDI Page” on page 49 for MIDI setup details. NOTE The DME Designer can be used to set up the system so that scene recall operations and user parameter control can be carried out from connected MIDI devices. Refer to the DME Designer manual for details. By connecting the [MIDI OUT] terminal of a digital mixer (such as the DM2000) to the [MIDI OUT] of the DME64N/24N and making the proper settings on the mixer and the DME64N/24N, you can change scenes by sending program change messages from the mixer. MIDI Cable MIDI OUT MIDI IN DME64N/24N DM2000 Digital Mixer or Other Controller Connecting to an External Device If the [MIDI OUT] connector of the DME64N/24N is connected to the [MIDI IN] connector of an SPX2000 or similar digital effect unit, and if the DME64N/24N and SPX2000 are set up appropriately, DME64N/24N program change operations will case the corresponding effect to be recalled on the effect unit. MIDI Cable MIDI OUT MIDI IN SPX2000 or Other Digital Effect Unit DME64N/24N 30 DME64N/DME24N Owner’s Manual Cascade Connection ([Cascade] Connectors) (DME64N only) Cascade Connection ([Cascade] Connectors) (DME64N only) The rear-panel [CASCADE] connector can be connected to the [CASCADE] connector on another DME64N/24N or other compatible device via a dedicated cascade cable for bidirectional transfer of control, audio, and word clock signals. The communication direction automatically switches to unidirectional when connecting to a mixer such as the PM5D, or bidirectional when connecting to another DME64N/24N unit. Up to eight DME64N units can be cascade connected. In the unidirectional mode the audio signal flow is from the [CASCADE OUT] connector to the [CASCADE IN] connector. For bidirectional communication the data flows in both directions within a single cable, and input on the same channel from other DME64N units is summed (bus sharing). The total number of audio channels that can be connected to a mixer or DME64N/24N unit is 32. Word clock is continuously output from both the [CASCADE IN] and [CASCADE OUT] connectors, and is received by the corresponding [CASCADE IN] or [CASCADE OUT] connector on the connected device. In all cases the [CASCADE OUT] of one device must be connected to the [CASCADE IN] connector of the other. Do not connect [CASCADE IN] to [CASCADE IN], or [CASCADE OUT] to [CASCADE OUT]. NOTE Maximum length by the optional dedicated Cascade cables Unidirectional Cascade connection: 200m (44.1/48kHz), 100m (88.2/96kHz) Bidirectional Cascade connection: 100m (44.1/48kHz), 30m (88.2/96kHz) Cascade Connection Example Unidirectional Cascade Connection 68-pin Half-pitch D-SUB Cable IN OUT DME64N Bidirectional Cascade Connection DME64N 68-pin Half-pitch D-SUB Cable OUT 68-pin Half-pitch D-SUB Cable IN PM5D DME64N 68-pin Half-pitch D-SUB Cable OUT IN OUT Connecting to an External Device IN DME64N NOTE Never create a full cascade loop using only DME64N units! NOTE It is also possible to remotely control DME series units from the PM5D via a CASCADE connection. In such cases assign the nearest DME64N unit to the PM5D as the device group master. When using a DME64N/24N together with the DME Satellite, you must assign the DME Satellite as the master. Another method of remotely controlling a DME series from a PM5D is via CobraNet connections to MY16-C or MY16-CII cards. All DME series units to be controlled from the PM5D must be in the same device group, and the host address of the device group master must be set to “2.” However, if the PM5D is version 2.20 or higher and the DME Satellite is version 3.07 or higher, you can set the parameter to any number. For information on the PM5D DME CONTROL function refer to the PM5D/PM5D-RH Owner’s Manual or to the “Cascade Setup Guide” available at the Yamaha website. http://www.yamahaproaudio.com/ DME64N/DME24N Owner’s Manual 31 WORD CLOCK Connection ([WORD CLOCK] Connectors) WORD CLOCK Connection ([WORD CLOCK] Connectors) Word clock signals are transferred to and from external devices via the [WORD CLOCK IN] and [WORD CLOCK OUT] connectors. The [WORD CLOCK OUT] connector can be used to supply the DME64N/24N word clock to external equipment. Word clock is continuously output by the DME64N/24N during normal operation. The word clock signal from an external device can be received via the [WORD CLOCK IN] connector. Refer to the Utility display WCLK page described on page 50 of this manual for details. NOTE Word clock can also be received and transmitted via a mini-YGDAI card installed in an I/O slot, or the [CASCADE IN] and [CASCADE OUT] connectors. It is necessary to specify whether the DME64N/24N will use the internal word clock or an external word clock for synchronization. NOTE A device transmitting the word clock signal that will be used by other devices for synchronization is the “word clock master,” while devices received the word clock are “word clock slaves.” WC OUT (BNC) WC IN (BNC) Word Clock Master DME64N/24N Word Clock Slave To distribute the word clock signal from one device to multiple slave devices, either a word clock distribution box or daisy-chained connection can be used. Distribution Box Connection Word Clock Master Word Clock Distribution Box WC OUT (BNC) WC IN (BNC) DME64N/24N WC IN (BNC) DME64N/24N Word Clock Slave WC IN (BNC) WC IN (BNC) DME64N/24N Word Clock Slave DME64N/24N Word Clock Slave Word Clock Slave Connecting to an External Device Daisy Chain Connection NOTE This method is not recommended for large systems. Word Clock Master WC OUT (BNC) WC IN (BNC) WC OUT (BNC) DME64N/24N Word Clock Slave 32 DME64N/DME24N Owner’s Manual WC IN (BNC) WC OUT (BNC) DME64N/24N Word Clock Slave WC IN (BNC) DME64N/24N Word Clock Slave GPI Connection ([GPI] Connectors) GPI Connection ([GPI] Connectors) GPI (General Purpose Interface) device (GPI controller, etc.) can be connected to the rear-panel [GPI] connectors. Using GPI a variety of control signals can be transferred between the DME64N/24N and external controllers or other devices. The optional CP4SW, CP4SF, and CP1SF control panels are also connected via GPI. NOTE For more information on the CP4SW, CP4SF, and CP1SF control panels refer to “CP4SW, CP4SF, and CP1SF” in the Appendix of this manual (page 51). The DME64N provides 16 channels of GPI input and output, and the DME24N provides 8 channels. Each channel has an IN terminal, a +V terminal, an OUT terminal and a GND terminal. The +V terminals have an open-terminal voltage of 5 volts. The IN terminals can detect a full range of input voltages from 0V through 5V, while the OUT terminals output either signal “L” or “H” at a TTL level. The parameters for each GPI input and output are assigned via the DME Designer application. NOTE The DME Designer can be used to set up the system so that scene recall operations and user parameter control can be carried out from connected GPI control devices. Refer to the DME Designer manual for details. Euroblock connectors are used for all GPI input and output connections. Euroblock connection methods are described in “Euroblock Connection” on page 26 in this manual. Example: Controlling the DME64N/24N from a switch. GPI Connection IN +V Example: Controlling the DME64N/24N via a 10k ohm linear taper potentiometer. GPI Connection IN +V Example: Lighting external LED indicators from the DME64N/24N. GPI Connection OUT GND GND Max. 16mA CAUTION Make sure that the current between the OUT and GND [GPI] connectors is less than 16mA. Connecting to an External Device Continuous potentiometer NOTE GPI connector calibration procedure is described on page 51 of this manual, in the Utility display GPI page. DME64N/DME24N Owner’s Manual 33 Basic Operation Panel Operation and Displays Basic Operation By pressing the panel buttons it is possible to select the DME64N/24N Main display, Utility display, and Parameter Edit displays that allow individual settings to be edited and changed. refer to the pages listed below for more detailed information about each display. [HOME] button  Main Display (page 35) The Main display can be directly recalled from any display other than the Main display by pressing the [HOME] button. The Main display shows the current scene information. HOME [HOME] button  User Defined Button Page Selection (page 38) Pressing the [HOME] button while the Main display is shown sequentially selects the four User Defined Button pages. HOME Main display Switches the pages of the User Defined Button [MUTE] button  Mute Display (page 39) [LEVEL] button  Output Level Display (page 39) [SCENE] button  Scene Recall Display (page 39)/Scene Store Display (page 40) These buttons can be pressed from the Main or Utility displays to directly call the related parameter edit displays. [MONITOR] button  Monitor Point Selection Display (page 40) This function is useful for level monitoring. When the button is pressed the monitor point selection display will appear, and the spectrum analyzer display will appear when a selection has been made. Panel Operation and Displays [UTILITY] button  Utility Display (page 43) The Utility display appears when the [UTILITY] button is pressed for longer than two seconds while the Main display is showing. The Utility display includes a number of pages that can be selected in sequence by repeatedly pressing the [UTILITY] button. 34 DME64N/DME24N Owner’s Manual Main Display Main Display The Main display will appear in a few seconds after the power is turned on. The Main display shows information about the current scene. Buttons are selected for editing by using the cursor buttons – [ E ] [  ] [  ] [ F ] – to select the button, and then pressing [ENTER]. NOTE User Defined Button settings are common to the device group. NOTE Nothing will appear on the display if no scene data is stored in the DME64N/24N scene memory (this is the case when the unit is initially shipped, for example). Up to 24 parameters can be accessed from the DME64N/24N or ICP1 control panel for each scene. Six parameters are shown on the Main display at a time. 3 5 6 7 2 1 4 4 Page Scroll Bar The scroll bar provides an indication of which parameter page is currently being displayed. 4 pages are available, and the scroll bar moves one position to the right each time the [HOME] button is pressed and a new page of parameters is selected, and then back to the leftmost position after the rightmost position has been reached. NOTE Scroll bar operation is independent for each DME64N/ DME24N unit, and is not linked within a device group. 3 1 Scene Information 5 Mute Indicator The current scene number and name. Scene names can be entered by using the DME Designer application. A maximum of 12 one-byte (Roman) characters can be displayed in a scene name. When “two-byte” characters are to be used for languages such as Japanese, the total number of displayable characters is reduced accordingly. When the power is turned on the last scene selected before the power was turned off is automatically recalled. Shows the current mute ON/OFF status. 2 Edit Indicator If a parameter is changed after recalling a scene, a dot will appear in the scene number indicator, and “EDIT” will appear in the display. : Mute ON : Mute OFF 6 Output Level Indicator Displays the current output level in 10 increments. The longer the “bar,” the higher the output level. 7 Panel Lock Icon This icon appears when the panel lock function is turned ON. : Panel Lock ON (Panel controls locked) Panel Operation and Displays 3 User Defined Button Names Displays the User Defined Button. The buttons are specified by using the DME Designer application. “No Assign” settings in DME Designer are displayed as dotted lines. When [Parameter Value Edit] is selected the display will be a solid line. When [Direct Parameter Value], [Scene Change], [GPI Out], or [Play Wav File] are selected, the display will be inverted. A maximum of 24 buttons can be made available for user control, but only six buttons can be shown in any one display page. Press the [HOME] button to switch to other available button pages. A maximum of 8 one-byte (Roman) characters can be displayed in a button name. When “two-byte” characters are to be used for languages such as Japanese, the total number of displayable characters is reduced accordingly. DME64N/DME24N Owner’s Manual 35 Parameter Edit Displays Parameter Edit Displays Panel Lock The panel controls can be “locked” to prevent accidental mis-operation. To activate the panel lock function simultaneously press and hold the [HOME] and [ENTER] buttons for longer than 2 seconds. The panel lock icon will appear on the Main display when the panel is locked. Panel lock icon Panel Lock can be disengaged by pressing the [CANCEL] button for longer than 2 seconds. Parameter Edit displays will appear when the [SCENE], [MUTE], [MONITOR] or other button is pressed to allow scene changes, level adjustment, and other settings to be edited as required. Parameter Edit displays are also used to edit utility parameters. In most cases the desired parameter edit page can be accessed by selecting the item you want to edit in the appropriate display by using the cursor [ E ], [  ], [  ], and [ F ] buttons, and then pressing the [ENTER] button. There are basically three types of parameters that can be accessed via a Parameter Edit display: • Numeric values • Lists • ON/OFF switches NOTE Numeric Parameters The panel lock function can be set up to lock just the panel buttons (“Key Only”), or the panel buttons and GPI control (“Key+GPI”). You can also select whether or not the panel lock function is automatically engaged when the unit is initially turned on. This selection can be made via the Utility display “Lock” page (refer to the page 47). Numeric parameters can be edited in a number of ways, and depending on the parameter a fader, knob, or minimum and maximum values may appear to the left of the numeric value. A Numeric Value with a fader 1 5 2 4 A Numeric Value with a Knob 1 5 3 Panel Operation and Displays 4 1 Name of parameter selected for editing 2 Fader 3 Knob 4 Minimum and maximum values 5 Current value 36 DME64N/DME24N Owner’s Manual Parameter Edit Displays Some Parameter Edit displays have just one numeric parameter, while other may have two or more. 2. Rotate the dial to edit the value as required. 3. Repeat step 1 to select the next value to be edited, use the dial to edit as required, and repeat until all values have been edited as required. 4. When all values have been edited, press the [ENTER] button. A confirmation window will appear: press [ENTER] one more time to confirm the edits and close the window. Parameter Edit Display with One Numeric Parameter 1. Numeric values can be changed by rotating the dial. Dial rotation produces an immediate, corresponding change in the selected value. ENTER 2. Press the [ENTER] button to close the Parameter Edit display after the value(s) have been edited as required. Parameter Edit Display with Multiple Numeric Parameters ENTER Use the cursor buttons – [ E ] [  ] [  ] [ F ] – to select the value to be edited. Panel Operation and Displays NOTE 1. You can close the window without changing any values by pressing the [CANCEL] button rather than the [ENTER] button. DME64N/DME24N Owner’s Manual 37 Parameter Edit Displays List Parameters ON/OFF Parameters List parameters allow you to make one selection from a list of possibilities. Parameters that are either ON or OFF are edited via this type of display (e.g., Mute Parameter Edit display in “Mute Switching” on page 39). Rotate the dial to scroll up or down the list. In some cases the centermost item on the display will be always highlighted as the list is scrolled, and in others the same item will remain highlight as the list is scrolled up or down. 1. Rotate the dial clockwise to select ON, or counterclockwise to select OFF. 2. Press enter to confirm the selection and close the window. List Parameter with Center Item Always Highlighted Parameter Edit displays will also appear when the [SCENE], [MUTE], [MONITOR] or other button is pressed. These allow scene changes, level adjustment, and other settings to be edited as required. 1. Use the dial to scroll up or down the list. As you scroll the centermost item on the display will be highlighted. 2. Press the [ENTER] button to select the highlighted item and close the window. List Parameter with Scrolling Highlight 1. Press the [ENTER] button to highlight the centermost item on the display. NOTE Panel Operation and Displays In some cases a confirmation dialog will appear when the [ENTER] button is pressed. If this occurs press the [ENTER] button a second time to continue. 3. 1. If the Main display is not showing, press the [HOME] button to recall it. 2. Press the [HOME] button until the page containing the parameter to be edited appears. 3. Use the [ E ] [  ] [  ] [ F ] buttons select the parameter to be edited. 4. Press the [ENTER] button. The Parameter Edit display for the selected User Defined Button will appear. Use the dial to scroll up or down the list. As you scroll the highlighted selection will remain highlighted, and will scroll up or down with the list. 2. Editing User Defined Button Press the [ENTER] button to select the highlighted item and close the window. NOTE User Defined Button can be of all three types: numeric, list, and ON/OFF. NOTE When editing from an ICP1 control panel, the [F1] ~ [F6] buttons are used for button selection. 5. Edit the User Defined Button as required. Refer to “Parameter Edit Displays” on page 36 for editing procedures. NOTE Any changed User Defined Button values will be lost if the power is turned off or if scenes are changed. However, if the Last.Mem.Resume setting is ON, the setting will be preserved even when the power is turned off. To preserve the changed values, store the scene data. 38 DME64N/DME24N Owner’s Manual Parameter Edit Displays Mute Switching Turns the DME64N/24N output mute function ON or OFF. 1. Scene Recall This procedure recalls a new scene (refer to page 10). Press the [MUTE] button. NOTE The Mute Parameter Edit display will appear. The same procedure is used for scene recall from an ICP1 control panel. 1. Press the [SCENE] button. The Scene Recall display will appear. 2. Select Mute ON or OFF. The mute function is turned on or off as described in “ON/OFF Parameters” on page 38. NOTE To access this function from the ICP1 control panel, hold the [F6] button for longer than 2 seconds. 2. Select a new scene. Scenes are selected as described in the “List Parameters” section on page 38. NOTE All outputs in the device group, including the [PHONES] jack, are muted. Output Level Control Adjust the output level of the DME64N/24N. 3. Press the [ENTER] button. A confirmation window will appear. NOTE Output level settings apply individually to each DME64N/ 24N unit. There is no overall device group setting. This function cannot be accessed from the ICP1 control panel. Press the [LEVEL] button. The “Output Level” Parameter Edit display will appear. 2. Adjust the numeric output level parameter as required. 4. Press the [ENTER] button again. The new scene will be selected. CAUTION Panel Operation and Displays 1. Don’t turn the power off during a scene recall operation. Doing so can cause corruption of the current scene data. The Output Level parameter is adjusted as described in “Numeric Parameters” on page 36. The graphic fader provides a visual indication of the current output level setting. DME64N/DME24N Owner’s Manual 39 Parameter Edit Displays NOTE Scenes can also be changed from a computer or GPI/ MIDI controller connected to the device. The DME Designer application is used to make scene changes from a computer. If a GPI/MIDI controller is to be used for changes it must be initially set up for scene change control by using the DME Designer. Monitoring The monitor functions allow you to monitor the audio signal at the inputs or outputs of I/O slots, points between components, and other critical monitoring points. NOTE NOTE If head amplifier parameters are included in the recalled scene data, the head amplifier settings will be changed accordingly. User-defined monitoring functions, such as monitoring at points between components, must specified via the DME Designer application. NOTE These functions cannot be accessed from the ICP1. Scene Store Stores the current scene data for later recall. 1. Press the [MONITOR] button. The slots available for monitoring will be shown in the parameter list. NOTE This function can be accessed in the same way from the ICP1. 1. Press the [SCENE] button for longer than 2 seconds. A confirmation window will appear on the display. 2. 2. Press the [ENTER] button. This stores the scene data in the current scene memory. NOTE Press the [CANCEL] button if you want to abort the scene store operation. NOTE Panel Operation and Displays If head amplifier settings are included in the scene the Utility display HA page settings are also stored. If head amplifier settings are not included in the scene, the HA page settings are stored as head amplifier startup settings. NOTE Any parameter values changed by GPI/MIDI controllers will be lost if the power is turned off or if scenes are changed. To preserve the changed values, store the scene data. 40 DME64N/DME24N Owner’s Manual Select the desired monitor source from the list. List selections are made as described in the “List Parameters” section on page 38. The following five position types can be selected: 1 Slot input/output terminal 2 CASCADE input/output terminal (DME64N only) 3 IN terminal (DME24N only) 4 OUT terminal (DME24N only) 5 User Defined By connecting 1 through 4 in DME Designer, you will be able to select the input/output terminal. You will be able to select 5 by editing the Monitoring Point List in DME Designer. Spectrum Display 3. Select the desired monitor point from the list. Spectrum Display The audio signal from the selected monitoring point will be output via the PHONES jack and the [MONITOR] indicator lights up. The monitor functions also provide spectrum analyzer type level display of the signal at the selected monitor point. NOTE NOTE Press the [CANCEL] button to move back to the previous edit display. Spectrum display is not available on the ICP1 control panel. NOTE Procedure When the monitoring function is set to ON ([MONITOR] indicator lit steadily), you can turn it OFF by pressing the [MONITOR] button. 1. Select the monitor point for which you want to see a spectrum display from the list. 2. Press the [ENTER] button. Probe Monitor Functions The Probe Monitor function allows monitoring points to be selected from the DME Designer application. For details, see the “DME Designer Owner’s Manual.” When the Probe Monitor function is used the monitoring point will change and the [MONITOR] indicator will flash. A spectrum display of the audio signal at the selected monitor point will appear. 1 4 3 NOTE The monitoring point selected in the DME64N/24N is disabled. 2 1 Frequency These are the separate frequency bands displayed. 2 Band Output Level Signal level is displayed independently in 31 separate frequency bands. Output level is displayed in 12 steps. 3 Peak Hold Panel Operation and Displays When the peak hold function is ON, peak levels since the current monitor point was selected are held indefinitely. Peak levels are cleared after one second when peak hold is OFF. To turn the peak hold function ON or OFF, move the cursor to the PEAK HOLD ON/OFF setting and press the [ENTER] button to alternately turn it ON or OFF. 4 L/R Select Indicates when the spectrum display is for the left or right channel. The same spectrum display will be shown for the L and R channels of all monitor points other than user-defined points specified via the DME Designer application. To switch between the L and R displays move the cursor to the CHANNEL L/R setting and press the [ENTER] button to alternately select L or R. NOTE The fall rate of the meters can be set up via the Utility display “Disp” page. DME64N/DME24N Owner’s Manual 41 Level Meter Display Level Meter Display Individually displays the input/output level for each channel. NOTE Level display is not available on the ICP1 control panel. 1. Make sure that the Main display is showing. If the Main display is not showing, press the [CANCEL] to return. 2. Initializing the DME64N/ DME24N The DME64N/DME24N and ICP1 internal memories can be initialized as follows. Begin with the power turned off. Turn the power on while holding the [SCENE] and [ENTER] buttons, and continue to hold those buttons until the Yamaha logo appears. The initialization screen will appear, allowing you to choose one of the following three options. Press the [UTILITY] button. The level meter display will appear. SCENE 1 HOME UTILITY LEVEL MUTE CANCEL ENTER 4 1.Holding down the [SCENE] and [ENTER] buttons 3 2.Press the [POWER] button Plug the PA-300 AC adaptor while holding down the [SCENE] and [ENTER] buttons 2 1 Level Display Slot Select from [SLOT1] ~ [SLOT4], [AD/DA], [CASCADE IN] or [CASCADE OUT]. NOTE [SLOT2] ~ [SLOT4] and [CASCADE IN], [CASCADE OUT] are only available on the DME64N, while [AD/DA] is only available on the DME24N. 2 Channel Number A maximum of 32 [CASCADE IN]/[CASCADE OUT] channels can be displayed, while for other channels a maximum of 16 can be displayed. 3 Input/Output Level Display Shows the levels at the individual inputs and outputs. 01.Initialize DME: All scenes, preset parameter settings and WAVE files except components and files saved via the File Storage function will be deleted. All UTILITY settings are reset to their default values. 02.Delete All Data: All internally-stored components, scenes, preset parameters, wave files, and files stored using the File Storage function are erased. All UTILITY settings are reset to their default values. Use this problem when a problem occurs with the data stored in the device. After initialization, make sure to update the firmware and the components from the DME Designer application. Refer to the DME Designer Owner’s Manual for details. 03. ==> Exit Diag Mode: Panel Operation and Displays 4 Peak Hold Exits from the initialization screen and restarts the unit. When the peak hold function is set to ON, peak levels are held indefinitely. Peak levels are cleared after one second when peak hold is set to OFF. Do not turn off the power during initialization. Doing so can damage the device. To turn the peak hold function ON or OFF, move the cursor to the PEAK HOLD ON/OFF setting and press the [ENTER] button to alternately turn it ON or OFF. 42 DME64N/DME24N Owner’s Manual Utility Displays Utility Displays Most basic DME64N/24N functions can be accessed via the Utility Display. Items accessible via the Utility display Page Item Info Description Manual Page Current status and settings for the devices basic parameters. Label Page 45 Name display. Version The device’s current version number. Date Current status and setup for the internal calendar/clock. Battery Shows the status of the internal battery. MASTER/SLAVE Displays current status and determines whether the device is device group master or not. IP Adr. Current status and setup for the device’s IP address. Master ID Displays and sets the device group master host address. Net Current status and settings for the Ethernet network. Link Mode Current status and setup for the [NETWORK] connector. MAC Adr. Displays the device’s MAC address. Disp Page 46 Current status and setup for the display mode, etc. LCD Contrast Current status and setup for display panel contrast. LCD Backlight Current status and setup for the display panel backlight. Meter Fall Time Current status and setup for meter fall time. Utility Current status and setup for the Utility display settings. Lock Page 46 Current status and setup for panel lock and related functions. Page 47 Panel Lock Boot Current status and setup for the DME64N/24N’s power-on panel lock status. Panel Lock Target Current status and setup for the panel lock target. User Defined Lock Panel lock and setup for each page of User Defined Button. Scene Store Current status and setup for scene store accessibility. Misc Current status and setup for settings not included in other pages. Page 48 Last Mem. Resume Indicates and determines whether the previous memory contents will be retained when the unit is restarted. Current status and setup whether an event schedule setup in the DME Designer will be executed or not. Rmt Ctrl Displays/sets the connector and connection type to be used for DME remote control protocol communication. Int HA Ctrl Displays/sets the connector to be used for internal head amp control. Ext HA Ctrl Displays/sets the type of connection to be used for external head amp control. COM Displays/sets the type of connection to be used for DME protocol communication. MIDI Current status and setup for MIDI functions. Page 49 Port Current status and setup of the MIDI port. Protocol Displays/sets the protocol to be used for communication with devices connected via MIDI. CH Current status and setup for the MIDI transmit and receive channels. Program Change Current status and setup for program change transmission/reception, omni on, and echo on/off. Control Change Current status and setup for control change transmission/reception, omni on, and echo on/off. Param Change Current status and setup for parameter change transmission/reception, omni on, and echo on/off. Fs Displays the word clock frequency. Int Current status of the internal word clock. Current status and selection of the DME64N/24N word clock. WCLK Page 48 Panel Operation and Displays Remote Event Scheduler Page 50 WCIN Current status of the word clock received at the [WORD CLOCK IN] connector. Cascade Current status of the word clock received via the [CASCADE IN] and [CASCADE OUT] connectors. SLOT1-4 Current status of the word clock received via cards plugged in to the I/O card slots. DME64N/DME24N Owner’s Manual 43 Utility Displays Page Item Displays info about an I/O card installed in a DME64N/24N I/O slot. Slot Card name Displays the name of the installed card. (no title) Resets the installed card. Format Displays the audio format – 88.2 or 96 kHz. GPI connector calibration and status display. GPI Reset Resets the GPI calibration. Max Sets the maximum calibration value. Min Sets the minimum calibration value. (no title) Current calibration status. HA Current status and setup for head amplifier type. WCLK Current status and setup for the word clock used by the head amplifier(s). (no title) Displays the audio format 88.2/96 kHz. Gain Current status and setup for individual head amplifier channel gain. +48V Current status and setup for individual head amplifier channel phantom power supply (+48V ON/OFF). (no title) Displays current status of the master phantom power switch. Current status and setup for the internal and connected external head amplifiers. HA HPF Current status and setup for individual head amplifier channel high-pass filter on/off. Frq Current status and setup for individual head amplifier channel high-pass filter frequency. CASCAD (DME64N Head Margin only) Check Description Displays current status for the [CASCADE] connectors. Page 51 Page 51 Page 52 Page 53 Displays current status for the head margin of the audio signal handled via the [CASCADE] connectors. Unit No. Displays how many devices the unit is from the beginning of the cascade chain. Mixer I/O Displays current status for the channels to be used for audio signals cascaded to a mixer. Mode Current status and setup for the thru connection. Panel Operation and Displays 44 Manual Page DME64N/DME24N Owner’s Manual Page 54 Utility Displays 2 Program Version Utility Display Operation This is the current firmware version number. The general procedure for operating the Utility displays is outlined below. 1. Press the [UTILITY] button for longer than 2 seconds from the Main display to go to the Utility display. 2. Press the [UTILITY] button as many times as necessary until the desired parameter page appears. 3 Date Shows the currently set date and time. The internal clock and calendar can be set here. Edit using the “Numeric Parameters” editing procedure described on page 36. NOTE “Zone slave” cannot be used to set this parameter. Date/Time Parameter Edit Dialog NOTE Press the [CANCEL] button to display the pages in reverse order. 3. Use the cursor buttons – [ E ] [  ] [  ] [ F ] – to select the parameter you want to edit. NOTE Day - Month - Year On the ICP1 the function buttons are used in place of the cursor buttons as follows: [F1] button: Left [F2] button: Up [F3] button: Right [F5] button: Down 4. Press the [ENTER] button. This either confirms a selection or edit, or calls the appropriate parameter edit page. Info Page Hour : Minute : Second 4 Battery Shows the status of the internal battery. “Low Battery” will appear when the battery needs to be replaced, and “No Battery” will appear when no battery is present in the device. 5 Daylight Saving Time If you enable daylight saving time, the display will indicate “DST.” You can enable daylight saving time using DME Designer from a connected computer. NOTE Daylight saving time cannot be set on the DME64N/24N itself. 1 2 5 Panel Operation and Displays 3 4 NOTE The date and time (3) and the internal battery status (4) are not shown on the ICP1 control panel display. 1 Label Shows the name. The name can be changed via the DME Designer application running on a computer connected to the unit. NOTE The name can not be changed from the DME64N/24N controls. DME64N/DME24N Owner’s Manual 45 Utility Displays Network Settings (Net) Page Shows the Ethernet network address and other parameters. 3 Master ID Displays and sets the device group master host address. NOTE This is not displayed on the device group master device. 1 2 3 4 5 4 Link Mode Indicates whether or not the device is functioning as the device group master: “Master” or “Slave.” Master: the device is the device group master. Slave: the device is a device group slave. Shows the status of the [NETWORK] connector. The [NETWORK] connector can be set to operate in “10Base-T” or “100Base-TX” mode. 10Base-T: The [NETWORK] connector is compatible with 10Base-T operation. 100Base-TX: The 100Base-Tx: [NETWORK] terminal operates as 100Base-TX if possible. If the network environment does not support 100BaseTX, it operates as 10Base-T. Edit using the “List Parameters” editing procedure described on page 38. Edit using the “List Parameters” editing procedure described on page 38. 1 Master/Slave NOTE Device group status of ICP1 is fixed to “Slave.” This cannot be changed. NOTE 5 MAC Adr. This is the device’s MAC (Media Access Control) address. NOTE Make sure that one device group master is assigned for each device group. If no device group master is assigned, no scene information will appear on the display and scene-related control will not be possible. Mute operations will also not be possible. The MAC address is also known as the Ethernet address, and is an independent address assigned to all Ethernet devices. No two devices anywhere in the world can have the same address. Display Setup (Disp) Page 2 IP Adr. This is the device’s IP address. Edit using the “Numeric Parameters” editing procedure described on page 36. Provides access to a number of display parameters. NOTE The meter fall time (3) is not shown on the ICP1 control panel display. Panel Operation and Displays 1 2 Network Address Host Address 3 NOTE The network addresses of devices in the same device group must be the same. NOTE Device group master's IP address can be changed via the DME Designer application running on a computer connected to the unit. 46 DME64N/DME24N Owner’s Manual 1 LCD Contrast The current LCD contrast setting. This parameter can be adjusted from 0% through 100%. Edit using the “Numeric Parameters” editing procedure described on page 36. Utility Displays 2 LCD Backlight Specifies LCD backlight operation. Two settings are available: “ON,” and “OFF.” ON: The display is continuously lit. OFF: The display lights when a control is operated, and will go out 10 seconds after panel operation ceases. Pressing the [ENTER] button alternately selects “ON” and “OFF”. The password will also be required when switching from the “Unlock” mode to the “Lock” mode. NOTE Password security and management is very important! If you forget your password the unit cannot be operated! If you forget your password contact the system administrator. If the password become unrecoverable for some reason and you need to unlock the system, please contact your Yamaha representative. 3 Meter Fall Time Determines the fall time of the level meters – “Fast” or “Slow.” Fast: The meters rapidly follow changes in the signal level. Slow: The meters fall slower than the actual changes in the signal level, allowing easier reading in some cases. Edit using the “List Parameters” editing procedure described on page 38. Security Setup (Lock) Page Panel lock and related settings. 1 2 3 2 Panel Lock Boot Determines whether or not panel lock will be on when power to the device is turned on. This parameter can be set to “Unlock” or “Lock.” Unlock: Panel lock is OFF when power to the device is turned on. Lock: Panel lock is ON when power to the device is turned on. 3 Panel Lock Target Determines the controls (control functions) to be affected by panel lock. The available settings are “Key Only” and “Key+GPI.” Key Only: Panel lock only affects the panel buttons. Key+GPI: Panel lock applies to the panel buttons as well as GPI control input. NOTE See page 36 for details on how to use the Panel lock feature. 4 NOTE The lock status for the Utility display settings. This parameter can be set to “Unlock” or “Lock.” Unlock: The Utility display can be accessed without a password. Lock: A password must be entered to access the Utility display. When “Lock” is selected a password entry window will appear when the [UTILITY] button is pressed to access the utility pages. This parameter is displayed, but cannot be changed on the ICP1 display. 4 User Defined Lock Sets the lock status individually for each of the four User Defined Button pages. ON: The corresponding User Defined Button will not appear on the display. OFF: The corresponding User Defined Button will appear on the display. Panel Operation and Displays 1 Utility To change the settings use the [ E ] and [ F ] buttons to move the cursor to the setting for the desired page, the press the [ENTER] button to alternately turn the setting “ON” and “OFF.” NOTE The User Defined Button are accessed as described in the “Parameter Edit Display” section on page 36. Use the [ E ] and [ F ] buttons to position the cursor, and the dial to enter the desired character at the cursor location. When all of the password’s characters have been entered as required press the [ENTER] button. DME64N/DME24N Owner’s Manual 47 Utility Displays Miscellaneous Setup (Misc) Page This page includes parameters not available in any other page. 1 2 3 3 Event Scheduler Determines whether an event schedule setup in the DME Designer will be executed or not, and displays the current status. This parameter can be set to “ON” or “OFF.” ON: The event will be executed. OFF: The event schedule will not be executed. Edit using the “List Parameters” editing procedure described on page 38. NOTE This parameter can be changed from the device group master only. 1 Scene Store Determines whether or not scene store operations are allowed. This parameter can be set to “Enable” or “Disable.” Enable: Scene store operations are allowed. Disable: Scene store operations are prohibited. Edit using the “List Parameters” editing procedure described on page 38. NOTE 1 2 3 4 This item cannot be set if Internal HA Ctrl is set to Remote. NOTE NOTE This page will not appear on the ICP1 display. This setting applies to individual devices only. Even if one DME64N/24N unit is set to “Disable,” scene store operations will be possible via another DME64N/24N in the same device group that is set to “Enable.” 2 Last Mem. Resume This parameter displays and determines whether the DME64N/DME24N will recall the current scene when started up, or whether the memory contents at the time the unit was turned off will be recalled. The possible settings are “ON” or “OFF”. ON: The memory contents at the time the unit was turned off will be recalled at startup. OFF: The current scene will be recalled at startup. Panel Operation and Displays NOTE This parameter can be changed from the device group master only. CAUTION 48 Remote Control Setup (Remote) Page If “Last Mem. Resume” is set to ON, the unit will back up data to the internal memory periodically. In this case, do not turn off the power to the unit within five (5) seconds after you operate any parameters. DME64N/DME24N Owner’s Manual 1 Rmt Ctrl (Remote Control) Displays/sets the connector and connection type to be used for DME remote control protocol* communication. If the selected terminal was previously assigned to a different function, a confirmation dialog will appear. Edit using the “List Parameters” editing procedure described on page 38. OFF: Select “OFF” when this function is not to be used. Remote (232C): External controllers (AMX, Crestron, etc.) control the DME64N/24N via the [REMOTE] connector using an RS-232C connection. Remote (422): External controllers (AMX, Crestron, etc.) control the DME64N/24N via the [REMOTE] connector using an RS-422 connection. Network: This setting allows the DME64N/24N to be controlled via the [NETWORK] terminal. When “Network” is selected it is also possible to select the port number to be used. Utility Displays Displays/sets the connector to be used for internal head amp control. From a single digital mixer, you can control the internal head amps of multiple DME series units within the device group. Set this parameter only on the DME series units that is connected directly to the digital mixer, and turn in “OFF” for other units. Edit using the “List Parameters” editing procedure described on page 38. OFF: Select “OFF” when this function is not to be used. Remote (422): Allows a digital mixer to control the internal head amps via RS-422 protocol. Slot1 [Slot1 ~ Slot4 (DME64N)]: Allows a digital mixer to control the internal head amps via the specified expansion slot. 3 Ext HA Ctrl (External head amp control) Displays/sets the type of connection to be used for external head amp control. OFF: Select “OFF” when this function is not to be used. Remote (422): Allows remote head amp control. Always use this setting when a remote head amp unit (AD8HR, AD824) is connected. Also, don’t change the setting while a remote head amp is connected. Doing so can damage the unit. 4 COM Displays/sets the type of connection to be used for DME protocol communication. This is a Yamaha maintenance function. Normally, set this to “OFF”. MIDI Setup (MIDI) Page 3 1 2 4 5 6 NOTE This page will not appear on the ICP1 display. 1 Port (MIDI port) Sets/displays the port to be used for MIDI communication. The available settings are: OFF, Remote(232C), Remote(422), MIDI, USB-1, USB-2, SLOT-1, SLOT-2, SLOT-3, and SLOT-4. OFF: Select “OFF” when this function is not to be used. Remote (232C): MIDI data will be received via the [REMOTE] connector using an RS-232C connection. Remote (422): MIDI data will be received via the [REMOTE] connector using an RS-422 connection. MIDI: The MIDI connector is the currently active MIDI port. USB-1, USB-2: The corresponding USB port is selected for MIDI input. Slot1 [Slot1 ~ Slot4 (DME64N)]: A card installed in the corresponding I/O slot is currently selected for MIDI input. Edit using the “List Parameters” editing procedure described on page 38. NOTE When the DME64N/24N is functioning as the device group master and is connected to a computer running the DME Designer application via USB, the MIDI port being used by the DME Designer will not be available. Panel Operation and Displays 2 Int HA Ctrl (Internal head amp control) DME64N/DME24N Owner’s Manual 49 Utility Displays 2 Protocol (MIDI Protocol Setup) Displays/sets the protocol to be used for communication with devices connected via MIDI. The available settings are: MIDI, DAW(Type1), and DAW(Type2). MIDI: Use this setting when any MIDI device other than a general-purpose ProTools controller (HUI protocol) or general-purpose Logic or Cubase controller (Mackie control protocol) is to be connected. DAW (Type1): Use this setting when a generalpurpose ProTools controller (HUI protocol) is to be connected. DAW (Type2): Use this setting when a generalpurpose Logic or Cubase controller (Mackie control protocol) is to be connected. Edit using the “List Parameters” editing procedure described on page 38. Refer to the DAW controller owner’s manual as well as the DME Designer manual for setup details. Word Clock Setup (WCLK) Page Shows the status of incoming word clock signals, and allows setup of the DME64N/24N master word clock. NOTE This page will not be displayed on the ICP1. 1 2 3 4 Master Clock Selection Procedure 1. Use the cursor [ E ], [  ], [  ], [ F ], buttons to select one of the square blocks representing the available master clock sources. 2. Press the [ENTER] button to select the master clock. NOTE “DAW” stands for “Digital Audio Workstation.” ProTools, Logic, and Cubase are DAW applications, and this parameter provides direct compatibility with a number of physical controls surfaces that are available for use with these DAW software packages. The following parameters are available when the Protocol parameter is set to MIDI. 3 CH Specifies the device’s MIDI transmit and receive channel: 1 ~ 16. Edit using the “List Parameters” editing procedure described on page 38. 1 Fs The current sampling frequency of the master word clock. The value shown here is determined by the system’s master word clock signal. To select the word clock to be used as the master, move the cursor to the appropriate word clock indication in this display – the [WORD CLOCK IN] clock, the cascade clock, or a slot clock, for example – and press the [ENTER] button. 2 Int Panel Operation and Displays 4 Program Change Sets the frequency of the internal word clock – 44.1 kHz, 48 kHz, 88.2 kHz, or 96 kHz. Turns transmission and reception, the omni mode, and echo ON or OFF for MIDI program change messages. Move the cursor to the required parameter, then press the [ENTER] button to alternately turn ON and OFF. 3 WCIN 5 Control Change 4 Cascade Turns transmission and reception, the omni mode, and echo ON or OFF for MIDI control change messages. Move the cursor to the required parameter, then press the [ENTER] button to alternately turn ON and OFF. 6 Parameter Change Turns transmission and reception, and echo ON or OFF for MIDI parameter change messages. Move the cursor to the required parameter, then press the [ENTER] button to alternately turn ON and OFF. 50 5 DME64N/DME24N Owner’s Manual Shows the status of the word clock signal at the [WORD CLOCK IN] connector. Shows the status of the word clock signal at the [CASCADE IN] and [CASCADE OUT] connectors. Utility Displays 5 SLOT1~4 Shows the status of the word clock signal input via I/O cards installed in the I/O slots. GPI Setup (GPI) Page Input calibration parameters for the [GPI] connector. The Status Icons A word clock signal is present, and this signal can be selected as the DME64N/24N word clock. NOTE This page will not appear on the ICP1 display. No word clock signal (cannot be selected as the master clock). A word clock signal is present, but is not in sync with the master word clock. Currently selected as the DME64N/24N word clock. Currently selected as the DME64N/24N word clock, but the clock signal is not useable. Inactive slot channel, or no I/O card is present in the slot. 1 2 4 3 1 Reset Slot Information (Slot) Page Displays the name of the card installed in an I/O card slot. Some cards can also be reset via this page. Resets GPI calibration. To reset the calibration, use the [ E ] [  ] [  ] [ F ] buttons to select ALL to reset all inputs, or select an individual input from 1 to 16 to be reset, then press the [ENTER] button. 2 MAX Sets the maximum calibration value. To set the MAX value, use the [ E ] [  ] [  ] [ F ] buttons to select ALL to set all inputs, or select an individual input from 1 to 16 to be set, then press the [ENTER] button to set the MAX value to the current input voltage. 2 1 3 NOTE 3 MIN The name of the installed card appears here. Sets the minimum calibration value. To set the MIN value, use the [ E ] [  ] [  ] [ F ] buttons to select ALL to set all inputs, or select an individual input from 1 to 16 to be set, then press the [ENTER] button to set the MIN value to the current input voltage. 2 Reset 4 Calibration Info Resets the installed card. Shows the calibration settings as well as the current input voltage. This page will not appear on the ICP1 display. 1 Card Name 3 Format Panel Operation and Displays Displays the 88.2/96 kHz audio signal transfer mode. The input setting is on the left and the output setting is on the right. No Display (Default): 44.1/48 kHz audio signal transfer. SP (Double Speed): An 88.2/96 kHz capable card is installed, allowing direct transfer at 88.2 or 96 kHz. CH (Double Channel): A 44.1/48 kHz card is installed, and 88.2 or 96 kHz audio is transferred by using two 44.1/48 kHz channels to transfer each channel of 88.2/96 kHz audio. The number of audio channels that can be handled in this mode is half the number of channels normally handled by the card. DME64N/DME24N Owner’s Manual 51 Utility Displays 2 WCLK (AD8HR/AD824 only) Head Amplifier Setup (HA) Page Provides access to the head amplifier settings. Refer to “REMOTE Connection” on page 28 for head amplifier control signal connection. NOTE This page will not appear on the ICP1 display. NOTE Some scenes include head amplifier settings. In such cases, the HA page settings will be saved along with the scene when it is stored. Internal Head Amplifier (DME24N only) 1 4 5 AD8HR 2 1 6 8 4 7 3 2 1 HA Panel Operation and Displays Specifies the type of head amplifier to be set up. The available options are AD8HR, AD824, and Built-in HA (DME24N only). When the AD8HR and AD824 are selected, a number indicating the connection order will also appear. Edit using the “List Parameters” editing procedure described on page 38. DME64N/DME24N Owner’s Manual Available settings of the AD824 are “SLOT,” “BNC,” “INT44.1K,” and “INT48K.” SLOT A: Sets the word clock signal input via I/O cards installed in the I/O slots as the master clock of the AD824. BNC: Sets the word clock signal at the BNC connector as the master clock of the AD824. INT44.1K: Sets the 44.1 kHz internal word clock as the master clock of the AD824. INT48K: Sets the 48 kHz internal word clock as the master clock of the AD824. 3 Format (AD8HR only) 4 5 52 Available settings of the AD8HR are “D OUT A,” “WCLK IN,” “INT44.1K,” “INT48K,” “INT88.2K,” and “INT96K.” D OUT A: Sets the word clock signal at the digital input as the master clock of the AD8HR. WCLK IN: Sets the word clock signal at BNC connector as the master clock of the AD8HR. INT44.1K: Sets the 44.1 kHz internal word clock as the master clock of the AD8HR. INT48K: Sets the 48 kHz internal word clock as the master clock of the AD8HR. INT88.2K: Sets the 88.2 kHz internal word clock as the master clock of the AD8HR. INT96K: Sets the 96 kHz internal word clock as the master clock of the AD8HR. 5 AD824 1 Specifies the word clock signal to be used by the head amplifier(s). Displays the 88.2/96 kHz audio signal transfer mode. The input setting is on the left and the output setting is on the right. No Display (default): 44.1/48 kHz audio signal transfer. SP (Double Speed): Allows direct transfer at 88.2 or 96 kHz. CH (Double Channel): 88.2 or 96 kHz audio is transferred by using two 44.1/48 kHz channels to transfer each audio channel of 88.2 and 96 kHz respectively. The number of audio channels that can be handled in this mode is half the number of channels normally handled by the AD8HR. 4 Gain Individually sets the gain of each head amplifier channel. Edit using the “Numeric Parameters” editing procedure described on page 36. Utility Displays NOTE The gain of the DME24N internal head amplifiers can be adjusted from +10 dB to –60 dB in 1-dB increments. The internal circuitry switches at about the –45-dB point, and the signal is automatically muted at that point to prevent noise. The AD8HR gain can be adjusted from +10 dB to –62 dB in 1-dB steps, and the AD824 gain can be adjusted from +10 dB to –62 dB in 6-dB steps. The PAD will be internally switched on or off when the gain of the DME24N built-in head amplifier is adjusted between -8 dB and -7 dB. Keep in mind that noise may be generated if there is a difference between the Hot and Cold output impedance of the external device connected to the IN connector when using phantom power. Cascade Setup (CASCAD) Page Shows the status of the [CASCADE] connectors. Refer to “CASCADE Connection” on page 31 for connection details. Settings are made from the DME Designer application running on the connected computer. NOTE This page only appears on the DME64N. 1 2 3 5 +48V Individually turns phantom power ON or OFF for each head amplifier channel. Use the [ E ] and [ F ] buttons to position the cursor at the desired channel, then press the [ENTER] button to alternately turn phantom power for that channel ON and OFF. CAUTION • Always turn the phantom power off when it is not needed. • When turning phantom power ON, make sure that no equipment other than phantom-powered devices such condenser microphones are connected to the [IN] connectors (DME24N only). Applying phantom power to a device that does not require phantom power can damage the device. • Do not connect or disconnect a device to a [IN] connector (DME24N only) while phantom power is applied. Doing so can damage the connected device and/or the unit itself. • To prevent speaker and possible hearing damage, be sure to turn power amplifiers OFF when turning phantom power ON or OFF. It is also a good idea to turn the output level all the way down (page 39). 1 Head Margin Displays the head margin for cascade connection. 18dB: Use this setting when cascading DME64N units or when connecting to a mixer’s normal cascade bus. 0dB: Use this setting when connecting to a PM5D in situations in which the PM5D SLOT OUT port signal is being output via the CASCADE OUT terminal. NOTE The Head Margin setting only applies when connected to a mixer. When the DME64N is connected to another DME64N unit, head margin is fixed at 18 dB. 2 Unit No Shows how many devices the unit is from the beginning of the cascade chain. OUT 6 Phantom Master Switch (AD8HR only) 7 High-pass Filter (HPF) (AD8HR only) Individually turns the high-pass filter for each AD8HR head amplifier channel ON or OFF. This parameter is only available for the AD8HR head amplifier. Use the [ E ] and [ F ] buttons to select a channel, then press the [ENTER] button to turn the HPF for that channel ON or OFF. 8 High-pass Filter Frequency (Frq) (AD8HR only) Individually sets the high-pass filter frequency for each AD8HR head amplifier channel. This parameter is only available for the AD8HR head amplifier. Edit using the “Numeric Parameters” editing procedure described on page 36. PM5D OUT DME64N Unit No = 01 IN OUT DME64N Unit No = 02 IN DME64N Panel Operation and Displays IN Displays overall phantom power ON or OFF. Unit No = 03 3 Mixer I/O Displays whether the cascade signal is bus shared or not. : A DME64N connected directly to the mixer is connected to a second DME64N on this unidirectional channel. Input on the same channel from other DME64N units will be independent. : This channel is being used for bidirectional bus shared connection between DME64N units. Input on the same channel from other DME64N units will be summed. DME64N/DME24N Owner’s Manual 53 Utility Displays NOTE Make sure that the Mixer I/O setting is the same for all cascaded DME64N/24N units. Check Page Even in an environment with no computer, you can check the connections without using DME Designer by directly connecting the DME64N/24N input/output. The meter does not operate during a connection check. MODE: OFF Makes connections in the configuration used in the current scene. This is set to OFF when the unit is started. MODE: Thru Directly connects the Input and Output of each slot oneto-one for each channel. When input-only or output-only cards like AD or DA cards are inserted in the slots, you cannot perform checks in this mode. In the DME24N, the internal AD and internal DA are directly connected on each channel. Panel Operation and Displays MODE: Summing Sums all input signals coming from Inputs (-12dB), without regard to device or card type, and outputs it through all Outputs. NOTE This page will not appear on the ICP1 display. 54 DME64N/DME24N Owner’s Manual Options References Options The ICP1, CP4SW, CP1SF, and CP4SF controllers are available as options for remote external control of the DME series. The ICP1 connects via Ethernet, while the CP4SW, CP1SF, and CP4SF connect via the GPI interface. For more information on installing your Control Panel and connecting it to a DME series unit, refer to the owner’s manual that came with the Control Panel. For more information on settings, refer to the DME Designer Owner’s Manual. ICP1 This controller connects to a DME series unit via Ethernet. Like the DME series units, a unique IP address must be assigned to each controller unit. Data is transmitted and received via Ethernet cables. You can assign and control any function of all DME series units in the same device group via the controller. Up to four parameter sets can be assigned to six function buttons (F1 – F6) located above and under the LCD. You can control up to 24 parameters by selecting a display page using the [HOME] button. CP4SW, CP4SF, and CP1SF CONTROL PANEL CP4SW 10 10 10 10 10 0 0 0 0 0 CONTROL PANEL CONTROL PANEL CP4SF CP1SF DME64N/DME24N Owner’s Manual References These controllers connect to DME series units via the [GPI] connectors. These controllers control only the DME series units to which they are directly connected. The controller switches enable you to turn the parameter settings On and Off. The switch LEDs enable you to check the parameter status. The faders enable you to control the parameter values. 55 Error Messages Error Messages Message Meaning Action Error messages Cannot Select No selectable items are available in the scene or monitoring point list display. Make the appropriate settings via the DME Designer application. Component Corrupt Update Firmware! The component data is corrupt or can’t be found. Restart after updating the component using DME Designer. If the error indicators are still indicating the error, execute the “Delete All Data” initialization. If the problem persists, contact a Yamaha dealer. Critical Battery The internal battery is almost discharged. Your data may be lost. If you turn off power to the unit, the current settings may be lost and reset to the default values. Stop operating the unit, and contact a Yamaha dealer for battery replacement. Int.Data Corrupt Data inside the internal flash memory has been erased. Execute the “Delete All Data” initialization. If the problem persists, contact a Yamaha dealer. Invalid Password An invalid password has been entered. Enter the correct password. If you have lost or forgotten your password, contact a Yamaha dealer. Log Buffer Full Saving is not possible, since the Event Log saving area is full. Use DME Designer to delete the log. Low Battery The backup battery voltage is low. This does not affect the operation of the unit. However, if you continue using the unit, the settings may be lost and reset to the default values. Contact a Yamaha dealer for battery replacement at your earliest convenience. No Battery The internal battery is completely discharged or not installed. If you turn off the power to the unit, the current settings will be lost and reset to the default values. Stop operating the unit, and contact a Yamaha dealer for battery replacement. Param Access Err The current setting cannot be displayed because the parameter you attempted to operate does not exist. It is possible that the component is not operating normally. Save the current settings using DME Designer, execute the initialization (Delete All Data). If the problem persists, contact a Yamaha dealer. Param Set Err The current setting cannot be changed because the parameter you attempted to operate does not exist. It is possible that the component is not operating normally. Save the current settings using DME Designer, execute the initialization (Delete All Data). If the problem persists, contact a Yamaha dealer. ResumeData Corrupt Recall a Scene! The data has been partially corrupted due to power shutdown while writing to the internal memory. The current settings have been lost. Recall the scene again. If the problem persists, contact a Yamaha dealer. Resume Data Lost! Recall a Scene! Current setting has been lost. Recall the scene again. If the problem persists, contact a Yamaha dealer. Saving Failed A save operation has failed. Stop using the device immediately and contact a Yamaha dealer. Slots Overloaded The current being used by all cards installed in I/O slots exceeds the rated limit. Make sure that the total current consumption of the cards used does not exceed the limit. Store Disable The scene store parameter is set to “Disable.” Set the scene store parameter to “Enable” via the Utility display “Lock” page. Storing Failed Either the flash memory for storing data is full, or the file system has been damaged. Reduce the number of unused scenes. Alternatively, delete the files saved via the File Storage function. If deleting these items does not solve the problem, execute the Delete All Data initialization. If the problem persists, contact a Yamaha dealer. Cable Disconnect No network cable connected. Make sure that a network cable is properly connected, and that all network devices are functioning normally. Cannot be assigned No parameter assigned. Cannot Store The scene data is protected. Set the protect parameter to “OFF” via the DME Designer application. CAS. In Sync Err The DME64N/24N clock is not in sync with the clock signal being received at the [CASCADE IN] connector. Make sure that the DME64N/24N and the card or external source supplying the word clock are set to use the same word clock. CAS. Out Sync Err The DME64N/24N clock is not in sync with the clock signal being received at the [CASCADE OUT] connector. Make sure that the DME64N/24N and the card or external source supplying the word clock are set to use the same word clock. Connection to Master DME is Lost Communication with the master DME device has been interrupted. Check that all cables are properly connected, and than network switches, routers, and related devices are functioning properly. Connection to Slave SME is Lost Communication with the slave DME device has been interrupted. Check that all cables are properly connected, and than network switches, routers, and related devices are functioning properly. Status messages References 56 DME64N/DME24N Owner’s Manual — Error Messages Meaning Action The program has been successfully updated. — Downloading Do not turn off Program update in progress. Do NOT turn power off while the unit displays this message. — DSP Power Shortage Audio is not input or output and is muted due to insufficient DSP resources. This error sometimes occurs if you try to operate a configuration at 96 kHz that has been created with a word clock of 48 kHz. To operate a configuration at any word clock setting, use DME Designer to create a configuration with the word clock set to 96 kHz. Duplicate IP Adr. Duplicate IP addresses. Change the IP addresses so that there are no duplicates. Err: Wrong Device Group Settings The device group configuration set via DME Designer does not match the actual configuration. Use DME Designer to go off-line, create a configuration that correctly matches the actual configuration, and then go back on-line to synchronize the configuration. Executing A User Defined Button operation is in progress. — File Opening Do not turn off A file operation is in progress during which the computer manipulates scene data. Do NOT turn power off while the unit displays this message. — Illegal MAC Adr. An illegal MAC address has been encountered. This could be due to a hardware malfunction. Refer this problem to a contact a Yamaha dealer. Invalid IP Adr. The network IP address is not appropriate. Set an appropriate network IP address. Network Busy There is too much network traffic. Communication is not possible. Check the devices connected to the network. If there are too many devices connected, reduce the number of devices. Network Error One of the following errors has occurred on the network: • A cable has been unplugged. • The power to a network switch or router has been shut off. • A cable is in an inappropriate state (e.g. a heavy object has been placed on the cable, etc.). Static electricity can also cause errors. Locate and eliminate the cause of the error. Network Setup Preparing network connection. No Current Scene There is no data in the current scene. Send appropriate scene data from a computer running the DME Designer application. — No MAC Adr. MAC address not specified. This could be due to a hardware malfunction. Refer this problem to a Yamaha dealer. Panel Locked Panel operation not allowed. Press the [CANCEL] button for longer than 2 seconds to disengage panel lock and allow panel operation. Panel Unlocked Panel lock has been disengaged. Panel operation is now possible. Recovering Do not turn off A program update attempt has failed, and the previous program is currently being restored. Saving HA Info Do not turn off Head amplifier info save in progress. (Do not turn power off.) — Saving Setup Info Do not turn off Info set up via the Utility display (other than head amplifier info) is being saved. (Do not turn power off.) — Scene Recalling Do not turn off Scene recall in progress. Do NOT turn power off while the unit displays this message. — Scene Storing Do not turn off Scene store in progress. Do NOT turn power off while the unit displays this message. — Searching for Master DME Unit... Currently searching for the master DME unit. — Searching for Slave DME Unit... Currently searching for the slave DME unit. — SLOT1 Sync Err The DME64N/24N clock is not synchronized with the clock of the card installed in I/O slot 1. Make sure that the DME64N/24N and the card or external source supplying the word clock are set to use the same word clock. SLOT2 Sync Err The DME64N clock is not synchronized with the clock of the card installed in I/O slot 2. Make sure that the DME64N and the card or external source supplying the word clock are set to use the same word clock. SLOT3 Sync Err The DME64N clock is not synchronized with the clock of the card installed in I/O slot 3. Make sure that the DME64N and the card or external source supplying the word clock are set to use the same word clock. SLOT4 Sync Err The DME64N clock is not synchronized with the clock of the card installed in I/O slot 4. Make sure that the DME64N and the card or external source supplying the word clock are set to use the same word clock. — Do NOT turn power off while the unit is displaying this message. If the update attempt repeatedly fails, there may be a hardware malfunction. Refer this problem to a Yamaha dealer. DME64N/DME24N Owner’s Manual References Message Download Success 57 Error Messages Message Meaning Data is being received from the computer. Do NOT turn power off while the unit displays this message. — Updating Do not turn off Data is being received from the computer. Do NOT turn power off while the unit displays this message. — WCLK Unlocked A usable word clock signal is not being received or cannot be detected. Recheck all word clock connections and internal parameters. WCLK In Sync Err The DME64N/24N clock is not in sync with the clock signal being received at the WORD CLOCK IN] connector. Make sure that the DME64N/24N and the card or external source supplying the word clock are set to use the same word clock. References 58 Action Synchronizing Do not turn off DME64N/DME24N Owner’s Manual Troubleshooting Troubleshooting The power won’t turn on, and the panel indicators and LCD won’t light. • Is the power cable properly connected? • Is the POWER switch turned on? • If neither of the above is the problem, contact your Yamaha service center or representative. Cannot exchange data between the DME64N/24N and the DME Designer. • Are the network cables connected correctly? • Has the USB-MIDI driver been properly installed? • If you are using the [NETWORK] connector, has the DME-N Network Driver been properly set up? • Has a MIDI port been properly assigned (page 49)? • Are you using a version of DME Designer later than 3.8? No sound input. • Are the cables connected properly? • Is an appropriate signal being received from the external device? • Is the GAIN of the internal (DME24N) or external head amp set to an appropriate level? No sound output. • Are the cables connected properly? • Make sure that the output level isn’t turned down (page 39). • Is MUTE ON (page 39)? • Have you used DME Designer to select a scene that does not output audio? • Are you attempting to run a configuration that is not compatible with 96 kHz operation at 96 kHz? MIDI messages aren’t transmitted or received. • Is power to the MIDI device(s) turned on? • Are the MIDI ports properly set up (page 49)? • Are the receive and transmit device channels set appropriately? Scenes are not recalled when MIDI program change messages are received. • Have the settings required to receive program change messages been properly made (page 49)? • Use the DME Designer to set up the MIDI Program Change table as required. Parameter control does not function even when MIDI control change messages are received. • Make the settings required to allow control change reception. • Use the DME Designer to set up the MIDI Control Change table as required. Parameter control does not function even when MIDI parameter change messages are received. • Have the settings required to receive parameter change messages been properly made (page 49)? • Use the DME Designer to set up the MIDI Parameter Change table as required. Slow data transfer. • Set the LINK MODE to 100Base-TX (page 46). The desired scene can’t be recalled. • Write the require scene data from the DME Designer to the DME64N/24N. Scenes are recalled unexpectedly. • Is input being received from an external device or the DME Designer? • Use the DME Designer to check the MIDI Program Change Table settings. • Use the DME Designer to check the GPI input assignments. • Use the DME Designer to check the Remote Control Setup List assignments. • Set scene store to “Enable” (page 48). The 96kHz/88.2kHz/48kHz/44.1kHz indicator flashes red. • Select a different word clock source (page 50). • If an external device is functioning as the word clock master, check that the cables are connected properly. Noise appears on the analog outputs when an external device is the word clock master and the word clock source is switched. • Reduce the power amp level to prevent speaker damage, or turn the DME64N/24N off before switching clock sources. Use Defined Button settings change unexpectedly. • Use the panel lock function (page 38) to prevent unwanted operation of the panel controls on specific DME64N/24N or ICP1 units. User Defined Button settings cannot be changed. • Use the DME Designer to make sure that multiple User Defined Buttons are not assigned to the same parameter. • Turn the User Defined Lock function off (page 38). The panel controls cannot be operated. • Is the panel lock function on (page 36)? The Utility screen cannot be opened. • Is the Utility screen lock function on (page 47)? If you have forgotten your password contact your Yamaha service center or representative. References Scenes can be recalled but not stored. DME64N/DME24N Owner’s Manual 59 Specifications Specifications Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. Sampling Frequency Internal 44.1kHz, 48kHz, 88.2kHz, 96kHz External Normal Rate: 39.69 – 50.88kHz Double Rate: 79.39 – 101.76kHz Signal Delay (Fs = 96kHz) Memory DME64N: 0.85 msec (Input of MY8-AD96 to Output of MY8-DA96) DME24N: 0.5 msec ([IN] port to [OUT] port) Configuration 16 (depends on size of data) Scene 999 (depends on size of data) 160 x 64 dot matrix LCD with backlight Display 7-segment LED x 3 Scene No. Indicators Wordclock EXT.CLOCK, 96kHz, 88.2kHz, 48kHz, 44.1kHz External Control NETWORK, MIDI Zone Configuration MASTER Analog Input*1 SIGNAL x 8, PEAK x 8 Analog Output*1 SIGNAL x 8, PEAK x 8 Power Requirements 120V AC, 60Hz (USA, Canada) 230V AC, 50Hz (Europe) 100V AC, 50/60Hz (Japan) Power Consumption DME64N: 80W DME24N: 75W Dimensions (W x H x D) DME64N: 480 x 145 x 411.5mm, 3U DME24N: 480 x 101 x 411.5mm, 2U Weight DME64N: 9.5kg DME24N: 8kg Temperature Range Free-Air operating 10 – 35 °C Storage -20 – 60 °C AC Power Cord Length 2.5m Supplied Accessories AC power cord, Owner’s Manual, AC plug clamp, 16-pin Euroblock plug x 2, 8-pin Euroblock plug x 4 (DME64N), 3-pin Euroblock plug x 16 (DME24N) *1. Available on DME24N only European models Purchaser/User Information specified in EN55103-1 and EN55103-2. Inrush Current: 39A Conforms to Environments: E1, E2, E3 and E4 References 60 DME64N/DME24N Owner’s Manual Input/Output Characteristics Input/Output Characteristics Gain CH INPUT -60dB 1–8 +10dB Actual Load Impedance 3kΩ Input Level Connector Max. before clip For Use With Nominal Nominal 50 – 600Ω Mics & 600Ω Lines -60dBu (0.775mV) +10dBu (2.451V) Input CH INPUT 1–8 DME24N ANALOG INPUT CHARACTERISTICS Terminals Gain Error @1kHz -40dBu (7.75mV) +30dBu (24.511V) Internal OSC Input CH INPUT 1–8 DME64N ANALOG OUTPUT CHARACTERISTICS PHONES 15Ω For Use With Nominal 8Ω 40Ω Output Level Max. before clip Nominal 75mW 65mW 150mW 150mW Connector DME24N ANALOG OUTPUT CHARACTERISTICS Actual Source Impedance CH OUTPUT 75Ω 1–8 PHONES 15Ω For Use With Nominal 600Ω Lines 8Ω 40Ω Output Level Max. before Nominal clip +4dBu (1.23V) 75mW 65mW +24dBu (12.28) 150mW 150mW CASCADE IN – 24-bit Level RS422 Max. Units 6.0 6.0 2.0 dBu dBu dBu Output RL Conditions Min. Typ. Max. Units 0.1 % 0.05 % 0.1 % Total Harmonic Distortion fs=96kHz CH INPUT 1–8 Internal OSC Output RL Conditions Min. Typ. CH OUTPUT 600Ω GAIN = -60dB 1–8 @20Hz – 20kHz @+14dBu GAIN = +10dB @20Hz – 20kHz @+14dBu PHONES 8Ω -30dBFS @1kHz, phones level control: max. Input Connector Euroblock CH INPUT 1–8 Stereo Phone Jack Max. Units 0.1 % 0.05 % 0.1 % – Output RL Conditions Min. CH OUTPUT 600Ω GAIN = -60dB 1–8 Master fader at nominal level and one Ch fader at nominal level. (Mixer mode) 600Ω GAIN = +10dB Master fader at nominal level and one Ch fader at nominal level. (Mixer mode) PHONES 8Ω Residual output noise, phones level control: min. Typ. Max. Units -128 EIN -64 dBu dBu -82 dBu -86 dBu • Hum & Noise are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave attenuation. DME64N DIGITAL INPUT CHARACTERISTICS Format Data Length Typ. 4.0 4.0 0.0 Hum & Noise EIN = Equivalent Input Noise • 0dBu = 0.775 Vrms • All AD converters (CH1-8) are 24-bit linear, 128 times oversampling. • Stereo Phone Jack = unbalanced (Tip = LEFT, Ring = RIGHT, Sleeve = GND) Terminal Min. CH OUTPUT 600Ω GAIN = -60dB 1–8 @20Hz – 20kHz @+14dBu GAIN = +10dB @20Hz – 20kHz @+14dBu PHONES 8Ω -30dBFS @1kHz, phones level control: max. Input Stereo Phone Jack • 0dBu = 0.775 Vrms • Stereo Phone Jack = unbalanced (Tip = LEFT, Ring = RIGHT, Sleeve = GND) Output Terminals Conditions Total Harmonic Distortion fs = 48kHz Internal OSC Actual Source Impedance RL Euroblock • 0dBu = 0.775 Vrms • All AD converters (CH1-8) are 24-bit linear, 128 times oversampling. • +48V DC (phantom power) is supplied to CH INPUT (1-8) connectors via each individual controlled switch. Output Terminals Output CH OUTPUT 600Ω GAIN = -60dB 2.0 1–8 GAIN = +10dB 2.0 PHONES 8Ω -30dBFS @1kHz, -2.0 phones level control: max. Connector D-SUB Half Pitch connector 68P (Female) DME24N ELECTRICAL CHARACTERISTICS Dynamic Range Input DME64N DIGITAL OUTPUT CHARACTERISTICS Terminal Format Data Length CASCADE OUT – 24-bit Level RS422 CH INPUT 1–8 Connector D-SUB Half Pitch connector 68P (Female) Output RL Conditions Min. CH OUTPUT 600Ω GAIN = +10dB 1–8 Typ. Max. Units 106 dB • Dynamic range are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave attenuation. Crosstalk@1kHz From/To * CH INPUT 1-8 and CH OUTPUT 1-8 are provided on the DME24 only. Frequency Response 20Hz – 20kHz, reference to the nominal output level @1kHz Input CH INPUT 1–8 Internal OSC Output RL Conditions CH OUTPUT 600Ω GAIN = -60dB 1–8 PHONES 8Ω Min. Typ. Max. Units -1.5 0.0 0.5 dB -3.0 0.0 0.5 dB CH N To/From CH (N-1) or (N+1) Conditions Input CH INPUT 1–8 Internal OSC Output RL Conditions CH OUTPUT 600Ω GAIN = -60dB 1–8 PHONES 8Ω Min. Typ. Typ. Max. Units -80 dB Maximum Voltage Gain@1kHz Input CH INPUT 1–8 Output RL Conditions Min. CH OUTPUT 600Ω GAIN = -60dB 1–8 Typ. Max. Units 64 dB Phantom Voltage Output Frequency Response fs = 96kHz@20Hz – 40kHz, reference to the nominal output level @1kHz Min. CH1 – 8, adjacent inputs Conditions CH INPUT 1–8 hot, cold: No load Min. 46 Typ. 48 References DME64N/24N ELECTRICAL CHARACTERISTICS (Output impedance of signal generator: 150Ω) Max. Units 50 V Max. Units -1.5 0.0 0.5 dB -3.0 0.0 0.5 dB PEAK/SIGNAL Indicator Level Input Output Conditions GAIN +10dB PEAK red LED:ON Min. CH INPUT 1–8 – 25 – GAIN +10dB SIGNAL green -12 LED:ON CH OUTPUT PEAK red LED:ON 19 1–8 SIGNAL green LED:ON -18 Typ. Max. Units 27 29 dBu -10 -8 dBu 21 -16 23 -14 dBu dBu DME64N/DME24N Owner’s Manual 61 Control I/O Control I/O Terminals REMOTE Format Connector RS232C - RS422 MIDI IN/OUT/THRU - DIN Connector 5P WORDCLOCK IN/OUT TTL/75Ω BNC Connector Ethernet Ethernet - RJ-45 USB USB 0 – 3.3V USB Type B (Female) Euroblock Connector GPI IN 0 – 5V OUT TTL +V 5V DME64N: 16-GPI inputs and 16-GPI outputs DME24N: 8-GPI inputs and 8-GPI outputs Outputs: Imax/pin = 16mA Outputs: VH = 2.5V(min.), VL = 0.6V(max.) References 62 Level - DME64N/DME24N Owner’s Manual D-SUB Connector 9-pin (Male) Baud Rate = 38,400 bps Data = 8bit Stop bit = 1bit PARITY = NON Connector Pin Assign Connector Pin Assign [CASCADE IN/OUT] Connectors (DME64N only) CASCADE IN Pin No. Signal CASCADE OUT Pin No. Signal Pin No. Signal Pin No. Signal 1 GND 35 GND 1 GND 35 GND 2 INPUT 1-2 (+) 36 INPUT 1-2 (-) 2 OUTPUT 1-2 (+) 36 OUTPUT 1-2 (-) 3 INPUT 3-4 (+) 37 INPUT 3-4 (-) 3 OUTPUT 3-4 (+) 37 OUTPUT 3-4 (-) 4 INPUT 5-6 (+) 38 INPUT 5-6 (-) 4 OUTPUT 5-6 (+) 38 OUTPUT 5-6 (-) 5 INPUT 7-8 (+) 39 INPUT 7-8 (-) 5 OUTPUT 7-8 (+) 39 OUTPUT 7-8 (-) 6 INPUT 9-10 (+) 40 INPUT 9-10 (-) 6 OUTPUT 9-10 (+) 40 OUTPUT 9-10 (-) 7 INPUT 11-12 (+) 41 INPUT 11-12 (-) 7 OUTPUT 11-12 (+) 41 OUTPUT 11-12 (-) 8 INPUT 13-14 (+) 42 INPUT 13-14 (-) 8 OUTPUT 13-14 (+) 42 OUTPUT 13-14 (-) 9 INPUT 15-16 (+) 43 INPUT 15-16 (-) 9 OUTPUT 15-16 (+) 43 OUTPUT 15-16 (-) 10 DTR IN (+) 44 DTR IN (-) 10 DTR OUT (+) 44 DTR OUT (-) 11 RTS OUT (+) 45 RTS OUT (-) 11 RTS IN (+) 45 RTS IN (-) 12 GND 46 GND 12 GND 46 13 WORD CLOCK IN (+) 47 WORD CLOCK IN (-) 13 WORD CLOCK OUT 47 (+) WORD CLOCK OUT (-) 14 WORD CLOCK OUT 48 (+) WORD CLOCK OUT (-) 14 WORD CLOCK IN (+) WORD CLOCK IN (-) 48 GND 15 CONTROL IN (+) 49 CONTROL IN (-) 15 CONTROL OUT (+) 49 CONTROL OUT (-) 16 CONTROL OUT (+) 50 CONTROL OUT (-) 16 CONTROL IN (+) 50 CONTROL IN (-) 17 GND 51 ID6 IN 17 GND 51 ID6 OUT 18 GND 52 ID6 OUT 18 GND 52 ID6 IN 19 INPUT 17-18 (+) 53 INPUT 17-18 (-) 19 OUTPUT 17-18 (+) 53 OUTPUT 17-18 (-) 20 INPUT 19-20 (+) 54 INPUT 19-20 (-) 20 OUTPUT 19-20 (+) 54 OUTPUT 19-20 (-) 21 INPUT 21-22 (+) 55 INPUT 21-22 (-) 21 OUTPUT 21-22 (+) 55 OUTPUT 21-22 (-) 22 INPUT 23-24 (+) 56 INPUT 23-24 (-) 22 OUTPUT 23-24 (+) 56 OUTPUT 23-24 (-) 23 INPUT 25-26 (+) 57 INPUT 25-26 (-) 23 OUTPUT 25-26 (+) 57 OUTPUT 25-26 (-) 24 INPUT 27-28 (+) 58 INPUT 27-28 (-) 24 OUTPUT 27-28 (+) 58 OUTPUT 27-28 (-) 25 INPUT 29-30 (+) 59 INPUT 29-30 (-) 25 OUTPUT 29-30 (+) 59 OUTPUT 29-30 (-) INPUT 31-32 (+) 60 INPUT 31-32 (-) 26 OUTPUT 31-32 (+) 60 OUTPUT 31-32 (-) 27 ID0 IN 61 ID1 IN 27 ID0 OUT 61 ID1 OUT 28 ID2 IN 62 ID3 IN 28 ID2 OUT 62 ID3 OUT 29 ID4 IN 63 ID5 IN 29 ID4 OUT 63 ID5 OUT 30 ID0 OUT 64 ID1 OUT 30 ID0 IN 64 ID1 IN 31 ID2 OUT 65 ID3 OUT 31 ID2 IN 65 ID3 IN 32 ID4 OUT 66 ID5 OUT 32 ID4 IN 66 ID5 IN 33 MSB //LSB IN 67 2CH//4CH IN 33 MSB //LSB OUT 67 2CH//4CH OUT 34 FG 68 FG 34 FG 68 FG References 26 DME64N/DME24N Owner’s Manual 63 Connector Pin Assign [NETWORK] Connector (100Base-TX Ethernet, RJ-45) Pin Connection 1 TxD+ 2 TxD– 3 RxD+ 4 Unused 5 Unused 6 RxD– 7 Unused 8 Unused Straight/Cross Cable Wiring Details Straight Cables Pins Pins 1 —— 1 1 —— 3 2 —— 2 2 —— 6 3 —— 3 3 —— 1 4 —— 4 4 —— 4 5 —— 5 5 —— 5 6 —— 6 6 —— 2 7 —— 7 7 —— 7 8 —— 8 8 —— 8 References 64 Cross Cables DME64N/DME24N Owner’s Manual Dimensions Dimensions Unit: mm 12.5 53.5 278 388 411.5 394 405 11 DME64N 423 145 17.5 96 132 18.5 4-M3 90 30 300 90 480 12.5 References 53.5 278 388 411.5 394 423 90 300 480 30 101 88 18 4-M3 18 52 405 11 DME24N 90 DME64N/DME24N Owner’s Manual 65 MIDI Data Format MIDI Data Format 1. DME64N/24N MIDI Functions 1.1 Scene Change Scene recall occurs according to the “MIDI Program Change Table” assignments when appropriate MIDI Bank Select MSB/LSB and Program Change messages are received by the DME64N/24N. Corresponding MIDI Bank Select MSB/LSB and Program Change messages are also transmitted by the DME64N/24N when a scene recall operation is carried out via the panel controls, as specified by the “MIDI Program Change Table” assignments. Transmission does not occur when switching Configurations. 1.2 Parameter Control MIDI Control Change and Parameter Change messages transmitted to the DME64N/24N can be used to control parameters according to the “MIDI Control Change table” and “MIDI Parameter Change Table” assignments. Corresponding MIDI Control Change and Parameter Change messages are also transmitted by the DME64N/24N when a parameter is edited out via the panel controls, as specified by the “MIDI Control Change table” and “MIDI Parameter Change Table” assignments. 2. MIDI Data Flow MIDI IN MIDI Rx CH SW1 Bank Select MSB/LSB Program Change (Scene Recall) SW2 Control Change (Parameter Edit) SW3 Parameter Change (Parameter Edit) Bank Select MSB/LSB Program Change (Echo Back) SW4 Control Change (Echo Back) SW5 Parameter Change (Echo Back) SW6 Bank Select MSB/LSB Program Change Control Change Parameter Change SW7 MIDI Tx CH MIDI OUT SW8 SW9 MIDI THRU References SW1: Program Change Rx Switch [On/Off] SW2: Control Change Rx Switch [On/Off] SW3: Parameter Change Rx Switch [On/Off] SW4: Program Change Echo Back Switch [On/Off] SW5: Control Change Echo Back Switch [On/Off] SW6: Parameter Change Echo Back Switch [On/Off] SW7: Program Change Tx Switch [On/Off] SW8: Control Change Tx Switch [On/Off] SW9: Parameter Change MIDI Rx CH: MIDI Rx Channel (1-16) MIDI Tx CH: MIDI Tx Channel (1-16) 66 DME64N/DME24N Owner’s Manual MIDI Data Format 3. MIDI Setup Specifies basic MIDI operation. 3.1 Host Select Selects the input/output port to be used for MIDI communication. 3.2 DAW Controller Specifies the DAW controller type when a DAW control surface is to be used to control the DME64N/24N. When Type 1/2 is selected, Host Select is automatically set to MIDI. 3.3 MIDI Tx Channel Specifies the MIDI transmit channel (1 ~ 16). 3.4 MIDI Rx Channel Specified the MIDI receive channel (1 ~ 16). 3.5 MIDI Tx Switch Program Change Tx Switch: turns Bank Select MSB, LSB, and Program Change transmission on or off. Control Change Tx Switch: turns Control Change transmission on or off. Parameter Change Tx Switch: turns Parameter Change transmission on or off. 3.6 MIDI Rx Switch Program Change Rx Switch: turns Bank Select MSB, LSB, and Program Change reception on or off. Control Change Rx Switch: turns Control Change reception on or off. Parameter Change Rx Switch: turns Parameter Change reception on or off. 3.7 MIDI Omni Switch Program Change Omni Switch: turns the Bank Select MSB, LSB, and Program Change omni mode on or off. Control Change Omni Switch: turns the Control Change omni mode on or off. 3.8 MIDI Echo Back Switch Program Change Echo Back Switch: turns Bank Select MSB, LSB, and Program Change echo back on or off. Control Change Echo Back Switch: turns Control Change echo back on or off. Parameter Change Echo Back Switch: turns Parameter Change echo back on or off. 4. MIDI Format Number Format Notation Numbers ending with “h” are in hexadecimal format, while numbers ending with “b” are binary format. Characters “A” through “F” in hexadecimal numbers represent decimal values 10 through 15. Other lowercase characters (usually “n” or “x”) represent any number. MIDI Format Chart (Rx: receive, Tx: transmit) Rx/Tx Function Control Change (Bnh) Rx/Tx Parameter Change Scene Recall Program Change (Cnn) Rx/Tx System Real-time Message ACTIVE SENSING (FEH) Rx MIDI Cable Check System Exclusive Message Parameter Change Rx/Tx Parameter Change DME64N/DME24N Owner’s Manual References Command Channel Message 67 MIDI Data Format 4.1 Program Change (Cnh) Receive When the “Program Change Rx Switch” is on, Program Change messages are received on the MIDI channel specified by the “MIDI Rx Channel” parameter. If the “Program Change Omni Switch” is also on, however, Program Change messages will be received on all MIDI channels regardless of the “MIDI Rx Channel” setting. When a Program Change message is received, the scene assigned to the received program number in the “MIDI Program Change table” is recalled. The accepted Bank Select, Program Change range is as follows: Bank Select MSB: 0 Bank Select LSB: 0 ~ 7 Program Change No.: 0 ~ 127 Transmit When the “Program Change Tx Switch” is on, the corresponding Program Change number will be transmitted as specified by the “MIDI Program Change table” and “MIDI Tx Channel” settings. If multiple Program Change numbers are assigned to a single scene, the Bank Select MSB/LSB and Program Change number corresponding to the lowest number will be transmitted. Bank Select MSB Status Bnh (1101nnnnb) Control Change Data 00h (00000000b) Control Change No. 0 (Bank Select MSB) Data nnh (0nnnnnnnb) Control Value (Bank Select MSB No.) Status Bnh (1101nnnnb) Control Change Data 20h (00100000b) Control Change No. 32 (Bank Select LSB) nnh (0nnnnnnnb) Control Value (Bank Select LSB No.) Bank Select LSB Program Change No. Status Cnh (1100nnnnb) Program Change Data nnh (0nnnnnnnb) Program Change No. (0-127) 4.2 Active Sensing (FEh) Receive MIDI communication will be initialized if no data is received within 300 ms after reception (Running Status, etc., will be cleared). Active Sensing Status FEh (11111110b) Active Sensing 4.3 Control Change (Bnh) Receive When the “Control Change Rx Switch” is on, Control Change messages are received on the MIDI channel specified by the “MIDI Rx Channel” parameter. If the “Control Change Omni Switch” is also on, however, Control Change messages will be received on all MIDI channels regardless of the “MIDI Rx Channel” setting. Control Change parameter resolution is 128 regardless of the parameters effective range. For finer settings use Parameter Change. Transmit References When the “Control Change Tx Switch” is on, appropriate Control Change data will be transmitted when a parameter is edited via the panel controls, as specified by the “MIDI Control Change table” and “MIDI Tx Channel” settings. Transmission does not occur when switching Configurations. Refer to “Supplementary Information 1” for cases in which multiple messages are assigned to single parameter. Status Bnh (1011nnnnb) Control Change Data cch (0cccccccb) Control Change No. (1-31,33-95,102-119) vvh (0vvvvvvvb) Control Value (0-127) 4.4 Parameter Change (F0h ~ F7h) Receive When the “Parameter Change Rx Switch” is On, Parameter Change messages are received on the MIDI channel specified by the “Device ID (Rx Ch)” parameter. 68 DME64N/DME24N Owner’s Manual MIDI Data Format Transmit When the “Parameter Change Tx Switch” is On, appropriate Parameter Change data will be transmitted when a parameter is edited via the panel controls, as specified by the “MIDI Parameter Change table” and “MIDI Tx Channel” settings. Refer to “Supplementary Information 1” for cases in which multiple messages are assigned to single parameter. Refer to “Supplemental Information 2” for information on setting Parameter Data values. Status ID No. DEVICE ID. GROUP ID. MODEL ID. Parameter Address F0h 43h 10h 3Eh 10h aah aah ddh ddh ddh ddh ddh F7h Parameter Data Value EOX (11110000b) (01000011b) (0001xxxxb) (00111110b) (00010000b) (0aaaaaaab) (0aaaaaaab) (0dddddddb) (0dddddddb) (0dddddddb) (0dddddddb) (0dddddddb) (11110111b) System Exclusive Message Manufacturer's ID No.(YAMAHA) Rx/Tx Channel (0-15) Digital Mixer Device Code (DME) Parameter Address High Parameter Address Low data 0 data 1 data 2 data 3 data 4 End of Exclusive Supplemental Information 1 Messages Transmitted When Multiple Messages are Assigned to the Same Parameter The DME64N/24N MIDI transmit messages are specified via the “MIDI Control Change Table” and “MIDI Parameter Change Table.” The “MIDI Control Change Table” and “MIDI Parameter Change Table” can be set up via the DME Designer application. Multiple messages can be assigned to a single parameter, but the DME64N/24N will only transmit one of the assigned messages. The transmitted messages are as follows: • If a Control Change message and a Parameter Change message are assigned to the same parameter  the Control Change message will be transmitted. • If multiple Control Change numbers are assigned to the same parameter  the smallest Control Change number message will be transmitted. • If multiple Parameter Change numbers are assigned to the same parameter  the smallest Parameter Change number message will be transmitted. Supplemental Information 2 Setting the Parameter Change Message Parameter Data Values sign 0 0 13tib 03tib 92tib 82tib 72tib 62tib 52tib 42tib 32tib 22tib 12tib 02tib 91tib 81tib 71tib 61tib 51tib 41tib 31tib 21tib 11tib 01tib 9tib 8tib 7tib 6tib 5tib 4tib 3tib 2tib 1tib 0tib The Parameter change parameter values are expressed as 32-bit integers with or without parity. • A parity bit (positive: 0, negative: 1) is added above the most significant value bit (bit 31). • Fractional parameters will be converted according to the integer table. • For integers with parity, negative numbers are expressed as the 2’s complement. data 0 data 1 data 2 data 3 data 4 Example • When value is 1000 (decimal) / 3E8h (hexadecimal): 0 0 0 0 0 3 E 8 References + 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 1 0 0 0 data 0 = 00h data 1 = 00h data 2 = 00h data 3 = 07h data 4 = 68h • When value is 1000 (decimal) / FFFFFC18h (hexadecimal; 2’s complement of 3E8h): - F F F F F C 1 8 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 1 1 0 0 0 data 0 = 1Fh data 1 = 7Fh data 2 = 7Fh data 3 = 78h data 4 = 18h DME64N/DME24N Owner’s Manual 69 MIDI Data Format YAMAHA [Digital Mixing Engine] Model DME64N/24N MIDI Implementation Chart Date :31-MAR-2004 Version : 1.0 MIDI Data Format Function... Transmitted Recognized Basic Channel Default Changed 1 1 Mode Default Messages Altered × × ************** × × × × ************** × × Note Number : True voice - 16 16 1 1 Velocity Note ON Note OFF × × × × After Touch Key’s Ch’s × × × × × × Pitch Bend 0,32 1-31,33-95,102-119 O O *1 *2 - Remarks Memorized 16 16 O O *1 *2 Bank Select Assignable Control Change Prog Change : True # System Exclusive O 0 127 ************** O *1 *3 O : Song Pos. × : Song Sel. × : Tune × × × × System Real Time : Clock : Commands × × × × All Sound Off Reset All Cntrls Local ON/OFF All Notes OFF Active Sense Reset × × × × × × × × × × O × : : : Mes- : sages : : References Notes: - O Common Aux 0 0 127 *1 127 *3 Assignable not include “DAW controller” command *1 transmit/receive if program change switch is on. *2 transmit/receive if control change switch is on. *3 transmit/receive if parameter change switch is on. Mode 1 : OMNI ON , POLY Mode 3 : OMNI OFF, POLY 70 DME64N/DME24N Owner’s Manual Mode 2 : OMNI ON , MONO Mode 4 : OMNI OFF, MONO O : Yes × : No Glossary Glossary Explanations 100Base-TX A physical specification for a 100 Mbps Ethernet network connection using 2-conductor Category 5 UTP cable included in the IEEE 802.3u standard. Maximum data transfer distance is 100 meters. 10Base-T A physical specification for a 10 Mbps Ethernet network connection using 2-conductor Category 3 UTP cable included in the IEEE 802.3i standard. Maximum data transfer distance is 100 meters. BNC (Bayonet Nut Connector, or Bayonet Neill Concelman) A type of connector used for high-frequency connections using thin-core coaxial cable. An internal spring ensures a solid connection. Cascade A means of connecting Yamaha digital audio equipment to allow transfer of audio, control, and word clock signals. Yamaha cascade connections employ half-pitch 68-pin D-Sub connectors. Category 3 Electrical specifications for one type of UTP cable jointly developed by the TIA (Telecommunications Industry Association) and EIA (Electronic Industry Alliance). Several categories are specified according to electrical characteristics, with higher category numbers denoting higher quality cable. Category 3 cable can be used for transmission speeds up to 10 MHz. Category 5 Electrical specifications for one type of UTP cable jointly developed by the TIA (Telecommunications Industry Association) and EIA (Electronic Industry Alliance). Several categories are specified according to electrical characteristics, with higher category numbers denoting higher quality cable. Category 5 cable can be used for transmission speeds up to 100 MHz. Component The basic modules that are combined to create DME64N/24N audio systems. In addition to complete audio processors such as mixers, compressors, effects, crossovers, etc., a range of smaller functions such as faders, switches, pan controls, and meters are also available. Components can also be customized. Configuration A set of components and connections that make up an audio system in the DME64N/24N. D-Sub Another common form of connector that gets its name from the “D” shape of the connector. This type of connector can be securely attached using screws. Individual “pins” are used to connect each of the cable’s conductors. D-Sub connectors come in 9-pin, 15-pin, 25-pin, 37-pin, and other sizes. DSP (Digital Signal processor) A semiconductor chip (LSI), or device containing one or more such chips, developed specifically to process large volumes of data in real time. Ideal for processing digital audio. Ethernet A network protocol jointly developed by the Xerox, DEC, and Intel corporations, and codified in the IEEE 802.3 industry standard. Transfer speeds have increased to 100 Mbps, 1000 Mbps, and 10 Gbps from the initial 10 Mbps, while maintaining network compatibility. Euroblock A connector system consisting of plug and socket components that allows easy, solder-less wiring for a range of installations and devices. Simply insert the wire into the plug slot, tighten the screw, and plug into the socket to complete the connection. GPI (General Purpose Interface) A general-purpose control interface that can be used to allow control of the DME64N/24N via external devices and custom-made controllers. Connections are made via a Euroblock connector. The optional CP4SW, CP1SF, and CP4SF control panels also connect via GPI. Initial Settings The initial values and settings of all editable parameters that will be in effect when a device is powered on for the first time after it is shipped from the factory. Also known as “default settings” or “initial factory settings.” MAC (Media Access Control) Address The MAC address is also known as the Ethernet address, and is an independent address assigned to all Ethernet devices worldwide. No two devices can have the same address. MIDI (Musical Instrument Digital Interface) An international standard for data communication between electronic musical instruments and audio devices. Mini YGDAI (Yamaha General Digital Audio Interface) card A standard for I/O cards that can be installed to Yamaha audio products. Phantom Power A power delivery system that allows power to be delivered to devices along with audio signals via standard balanced audio cables. The term “phantom” is applied because the system uses the audio conductors for power delivery without disrupting the audio signal – the power is not “seen” by the audio signal. Preset Parameter The parameter set of all components included in a configuration. RJ-45 An 8-conductor modular connector used for Ethernet cable and ISDN telephone connections. The appearance is similar to the RJ-11 connectors used for telephone lines, but the connector is actually somewhat larger. “RJ” stands for “Registered Jack,” and is a connector type included in the Bell System USOC (Universal Service Ordering Codes) standards. Router An equipment that relays data in network by selecting the most effective route. DME64N/DME24N Owner’s Manual References Terms 71 Glossary Terms RS-232C A serial communication protocol that allows data transfer over distances of up to 15 meters. RS232C interfaces usually employ 9-pin D-sub connectors. “RS” stands for “Recommended Standard,” and one of the standards developed by the EIA (Electronic Industry Alliance). RS-422 A balanced serial communication protocol that allows data transfer over distances of up to 1 kilometer. RS-422 offers higher data rates and greater reliability than the RS-232C protocol. Sampling Frequency The number of times per second an analog audio signal is “sampled” when it is being converted to digital audio. Scene A complete audio setup including configuration data and the related component preset parameters. Up to 999 scenes can be stored for each zone in a DME64N/24N audio system. STP (Shielded Twisted Pair) Cable A data transmission cable consisting of a shielded twisted pair. This type of cable is more resistant to noise and interference than UTP (Unshielded Twisted Pair) cable. Network Switch A network switch which automatically connects only ports through which communication is currently taking place. This reduces network load while maximizing security. This type of switch can often mediate between devices having different transmission speeds and standards. USB (Universal Serial Bus) A serial bus primarily used for connecting peripheral devices to computer equipment. The USB 1.1 standard allows data transfer rates of up to 12 Mbps. UTP (Unshielded Twisted pair) Cable A data transmission cable consisting of an unshielded twisted pair. This type of cable is less expensive and more commonly available than STP (Shielded Twisted Pair) cable, and is widely used in 10Base-T and 100Base-TX network connections. Word Clock A signal used to synchronize multiple interconnected digital audio devices. The word clock frequency will be the same as the sampling frequency of the audio signal being processed. References 72 Explanations DME64N/DME24N Owner’s Manual Index +48V ............................................................................ 53 [ E ] [  ] [  ] [ F ] Buttons 15 100Base-TX (Glossary) ............................................... 71 10Base-T (Glossary) .................................................... 71 [96kHz] [88.2kHz] [48kHz] [44.1kHz] Indicator ............ 14 Display ......................................................................... 15 Display Setup (Disp) Page ........................................... 46 DME Designer ............................................................. 13 DME-N Network Driver ................................................ 23 DSP (Digital Signal processor) (Glossary) ................... 71 D-Sub (Glossary) ......................................................... 71 A [AC IN] Connector ........................................................ 16 area ................................................................................ 9 audio ............................................................................ 11 B Band Output Level ....................................................... 41 Battery ......................................................................... 45 BNC (Bayonet Nut Connector, or Bayonet Neill Concelman) (Glossary) ..................................................................... 71 E [ENTER] Button ........................................................... 15 Error Messages ........................................................... 56 Ethernet (Glossary) ...................................................... 71 Ethernet Connection .................................................... 23 Euroblock ..................................................................... 26 Euroblock (Glossary) ................................................... 71 [EXT. CLOCK] Indicator ............................................... 14 F C cable clamp .................................................................. 18 Calibration Info ............................................................. 51 [CANCEL] Button ......................................................... 15 Card Name .................................................................. 51 CASCAD Page ............................................................ 53 Cascade (Glossary) ..................................................... 71 Cascade (WCLK Page) ............................................... 50 CASCADE connection ................................................. 31 [CASCADE IN] [CASCADE OUT] Connectors ...... 17, 31 cascade loop ................................................................ 31 Cascade Setup (CASCAD) Page ................................ 53 Category 3 (Glossary) .................................................. 71 Category 5 (Glossary) .................................................. 71 CH (Double Channel) (Slot Page) ............................... 51 CH (MIDI Page) ........................................................... 50 component (Glossary) ................................................. 71 Components .................................................................. 9 Configuration ................................................................. 9 configuration (Glossary) ............................................... 71 connector pin assign .................................................... 63 Control Change ............................................................ 50 control I/O .................................................................... 62 CP4SW, CP4SF, and CP1SF ...................................... 55 D Date ............................................................................. 45 Device control .............................................................. 11 device group .................................................................. 9 Device Group (Net Page) ............................................ 46 Device group control .................................................... 11 Dial ............................................................................... 15 dimensions ................................................................... 65 Disp Page .................................................................... 46 Format (HA Page) ........................................................ 52 Format (Slot Page) ...................................................... 51 Frequency .................................................................... 41 front panel .................................................................... 14 Frq ............................................................................... 53 Fs ................................................................................. 50 G Gain ............................................................................. 52 GPI (General Purpose Interface) ................................. 33 GPI (General Purpose Interface) (Glossary) ............... 71 GPI connection ............................................................ 33 [GPI] Connector ..................................................... 16, 33 Ground Screw .............................................................. 16 H HA ................................................................................ 52 HA Page ...................................................................... 52 Head Amplifier Setup (HA) Page ........................... 52, 54 Head Margin ................................................................ 53 High-pass Filter ............................................................ 53 High-pass Filter Frequency .......................................... 53 [HOME] Button ............................................................. 15 HPF .............................................................................. 53 I I/O card ........................................................................ 20 I/O card (installation procedure) .................................. 21 I/O Slots ....................................................................... 17 ICP1 ............................................................................. 55 [IN] [OUT] Connectors ........................................... 17, 26 Info Page ..................................................................... 45 initial settings (Glossary) .............................................. 71 DME64N/24N Owner’s Manual 73 Input/Output Level Display ........................................... 42 Int ................................................................................. 50 IP Adr. .......................................................................... 46 L L/R Select .................................................................... 41 Label ............................................................................ 45 LCD Backlight .............................................................. 47 LCD Contrast ............................................................... 46 [LEVEL] Button ............................................................ 15 Level Meter display ...................................................... 42 Link Mode .................................................................... 46 List Parameter ............................................................. 38 Lock Page .................................................................... 47 M MAC (Media Access Control) Address (Glossary) ....... 71 MAC Adr. ..................................................................... 46 Main display ................................................................. 35 [MASTER] Indicator ..................................................... 15 MAX ............................................................................. 51 Meter Fall Time ............................................................ 47 MIDI (Musical Instrument Digital Interface) (Glossary) .. 71 MIDI connection ........................................................... 30 MIDI Data Format .................................................. 66, 70 [MIDI IN] [MIDI OUT] [MIDI THRU] Connectors .......... 16 [MIDI] Indicator ............................................................ 15 MIDI Page .................................................................... 49 MIDI Setup (MIDI) Page .............................................. 49 MIN .............................................................................. 51 Mini YGDAI (Yamaha General Digital Audio Interface) card (Glossary) ............................................................ 71 Misc Page .................................................................... 48 Miscellaneous Setup (Misc) Page ............................... 48 Mixer I/O ...................................................................... 53 [MONITOR] Button ...................................................... 15 Monitoring .................................................................... 40 [MUTE] Button ............................................................. 15 Mute Indicator .............................................................. 35 Mute Switching ............................................................ 39 N Net Page ...................................................................... 46 [NETWORK] Connector ......................................... 17, 23 [NETWORK] Indicator .................................................. 14 Network Settings .......................................................... 22 Network Settings (Net) Page ....................................... 46 Network Switch (Glossary) .......................................... 72 Numeric Parameter ...................................................... 36 O ON/OFF Parameter ..................................................... 38 Options ........................................................................ 55 Output Level Control .................................................... 39 Output Level Indicator .................................................. 35 74 DME64N/24N Owner’s Manual P Page Scroll Bar ............................................................ 35 Panel Lock ................................................................... 36 Panel Lock Boot ........................................................... 47 Panel Lock Icon ........................................................... 35 Panel Lock Target ........................................................ 47 Parameter Change ...................................................... 50 Parameter Edit display ................................................. 36 Peak Hold (Level Meter display) .................................. 42 Peak Hold (Spectrum display) ..................................... 41 [PEAK] Indicator .......................................................... 15 Phantom Master Switch ............................................... 53 Phantom Power (Glossary) .......................................... 71 [PHONES] Jack ........................................................... 15 [PHONES LEVEL] Control ........................................... 15 Port (MIDI Page) .......................................................... 49 [POWER] Switch .......................................................... 15 preparation ............................................................. 18, 26 preset parameter (Glossary) ........................................ 71 Probe Monitor Function ............................................... 41 Program Change ......................................................... 50 Protocol (MIDI Page) ................................................... 50 R rear panel ..................................................................... 16 Remote Connection ..................................................... 28 [REMOTE] Connector ............................................ 17, 28 Remote Page ............................................................... 48 Reset (GPI Page) ........................................................ 51 Reset (Slot Page) ........................................................ 51 RJ-45 (Glossary) .......................................................... 71 router (Glossary) .......................................................... 71 RS-232C (Glossary) .................................................... 72 RS-422 (Glossary) ....................................................... 72 S sampling frequency (Glossary) .................................... 72 Scene ........................................................................... 10 scene (Glossary) .......................................................... 72 Scene Information ........................................................ 35 [SCENE NUMBER] Indicator ....................................... 15 Scene Recall ................................................................ 39 Scene Store (Misc Page) ............................................. 48 Scene Store (Operation) .............................................. 40 security cover mounting ............................................... 18 Security Setup (Lock) Page ......................................... 47 [SIGNAL] Indicator ....................................................... 15 Slot Information (Slot) Page ......................................... 51 Slot Page ..................................................................... 51 SLOT1~4 ..................................................................... 51 SP (Double Speed) ...................................................... 51 specifications ............................................................... 60 Spectrum display ......................................................... 41 status message ............................................................ 56 STP (Shielded Twisted Pair) Cable (Glossary) ............ 72 T troubleshooting ............................................................ 59 U Unit No ......................................................................... 53 USB (Universal Serial Bus) (Glossary) ........................ 72 USB Connection .......................................................... 22 [USB] Connector .......................................................... 14 USB-MIDI Driver .......................................................... 22 User Defined button ....................................................... 9 User Defined Button (Edit) ........................................... 38 User Defined Button Names ........................................ 35 User Defined buttons (User Defined parameters) ......... 9 User Defined Lock ....................................................... 47 Utility (Lock Page) ........................................................ 47 [UTILITY] Button .......................................................... 15 Utility display ................................................................ 43 Utility display (Operation) ............................................. 45 UTP (Unshielded Twisted pair) Cable (Glossary) ........ 72 V Version ......................................................................... 45 W WCIN ........................................................................... 50 WCLK (HA Page) ......................................................... 52 WCLK Page ................................................................. 50 Word Clock (Glossary) ................................................. 72 WORD CLOCK connection .......................................... 32 [WORD CLOCK IN] [WORD CLOCK OUT] Connectors ................................................................................ 16, 32 word clock master ........................................................ 32 Word Clock Setup (WCLK) Page ................................. 50 word clock slave .......................................................... 32 Z zones ............................................................................. 9 DME64N/24N Owner’s Manual 75 MEMO 76 DME64N/24N Owner’s Manual MEMO DME64N/24N Owner’s Manual 77 MEMO 78 DME64N/24N Owner’s Manual For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A. Tel: 714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México S.A. de C.V. Calz. Javier Rojo Gómez #1149, Col. Guadalupe del Moral C.P. 09300, México, D.F., México Tel: 55-5804-0600 BRAZIL Yamaha Musical do Brasil Ltda. Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi, CEP 04534-013 Sao Paulo, SP. BRAZIL Tel: 011-3704-1377 ARGENTINA Yamaha Music Latin America, S.A. Sucursal de Argentina Olga Cossettini 1553, Piso 4 Norte Madero Este-C1107CEK Buenos Aires, Argentina Tel: 011-4119-7000 PANAMA AND OTHER LATIN AMERICAN COUNTRIES/ CARIBBEAN COUNTRIES Yamaha Music Latin America, S.A. Torre Banco General, Piso 7, Urbanización Marbella, Calle 47 y Aquilino de la Guardia, Ciudad de Panamá, Panamá Tel: +507-269-5311 EUROPE THE UNITED KINGDOM Yamaha Music U.K. Ltd. Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, England Tel: 01908-366700 GERMANY Yamaha Music Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: 04101-3030 SWITZERLAND/LIECHTENSTEIN Yamaha Music Europe GmbH Branch Switzerland in Zürich Seefeldstrasse 94, 8008 Zürich, Switzerland Tel: 01-383 3990 AUSTRIA Yamaha Music Europe GmbH Branch Austria Schleiergasse 20, A-1100 Wien, Austria Tel: 01-60203900 CZECH REPUBLIC/SLOVAKIA/ HUNGARY/SLOVENIA Yamaha Music Europe GmbH Branch Austria Schleiergasse 20, A-1100 Wien, Austria Tel: 01-602039025 Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. ASIA POLAND Yamaha Music Europe GmbH Branch Sp.z o.o. Oddzial w Polsce ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland Tel: 022-868-07-57 THE PEOPLE’S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co.,Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: 021-6247-2211 THE NETHERLANDS/ BELGIUM/LUXEMBOURG Yamaha Music Europe Branch Benelux Clarissenhof 5-b, 4133 AB Vianen, The Netherlands Tel: 0347-358 040 FRANCE Yamaha Musique France BP 70-77312 Marne-la-Vallée Cedex 2, France Tel: 01-64-61-4000 INDIA Yamaha Music India Pvt. Ltd. 5F Ambience Corporate Tower Ambience Mall Complex Ambience Island, NH-8, Gurgaon-122001, Haryana, India Tel: 0124-466-5551 INDONESIA PT. Yamaha Music Indonesia (Distributor) PT. Nusantik Gedung Yamaha Music Center, Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: 21-520-2577 ITALY Yamaha Musica Italia S.P.A. Combo Division Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 KOREA Yamaha Music Korea Ltd. 8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong, Kangnam-Gu, Seoul, Korea Tel: 080-004-0022 SPAIN/PORTUGAL Yamaha Música Ibérica, S.A. Ctra. de la Coruna km. 17, 200, 28230 Las Rozas (Madrid), Spain Tel: 91-639-8888 MALAYSIA Yamaha Music Malaysia, Sdn., Bhd. Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-78030900 SWEDEN Yamaha Scandinavia AB J. A. Wettergrens Gata 1, Box 30053 S-400 43 Göteborg, Sweden Tel: 031 89 34 00 SINGAPORE Yamaha Music Asia Pte., Ltd. #03-11 A-Z Building 140 Paya Lebor Road, Singapore 409015 Tel: 747-4374 DENMARK YS Copenhagen Liaison Office Generatorvej 6A, DK-2730 Herlev, Denmark Tel: 44 92 49 00 TAIWAN Yamaha KHS Music Co., Ltd. 3F, #6, Sec.2, Nan Jing E. Rd. Taipei. Taiwan 104, R.O.C. Tel: 02-2511-8688 NORWAY Norsk filial av Yamaha Scandinavia AB Grini Næringspark 1, N-1345 Østerås, Norway Tel: 67 16 77 70 THAILAND RUSSIA Yamaha Music (Russia) Room 37, bld. 7, Kievskaya street, Moscow, 121059, Russia Tel: 495 626 5005 OTHER EUROPEAN COUNTRIES Yamaha Music Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: +49-4101-3030 AFRICA Yamaha Corporation, Asia-Pacific Sales & Marketing Group Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2303 MIDDLE EAST TURKEY/CYPRUS Yamaha Music Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: 04101-3030 OTHER COUNTRIES Yamaha Music Gulf FZE LOB 16-513, P.O.Box 17328, Jubel Ali, Dubai, United Arab Emirates Tel: +971-4-881-5868 Siam Music Yamaha Co., Ltd. 4, 6, 15 and 16th floor, Siam Motors Building, 891/1 Rama 1 Road, Wangmai, Pathumwan, Bangkok 10330, Thailand Tel: 02-215-2626 OTHER ASIAN COUNTRIES Yamaha Corporation, Asia-Pacific Sales & Marketing Group Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2303 OCEANIA AUSTRALIA Yamaha Music Australia Pty. Ltd. Level 1, 99 Queensbridge Street, Southbank, Victoria 3006, Australia Tel: 3-9693-5111 COUNTRIES AND TRUST TERRITORIES IN PACIFIC OCEAN Yamaha Corporation, Asia-Pacific Sales & Marketing Group Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2303 HEAD OFFICE Yamaha Corporation, Pro Audio Division PA26' Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2441 Yamaha Pro Audio global web site: http://www.yamahaproaudio.com/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ U.R.G., Pro Audio Division © 2004-2010 Yamaha Corporation 1009MWTO-F0 Printed in Japan WW20480