ADVERTENCIA!
PRECAUCIÓN: PARA REDUCIR EL RIESGO DE DESCARGA ELÉCTRICA, NO QUITE LA CUBIERTA
DE ESTE ALTAVOZ NO HAY USUARIOS.
PIEZAS REPARABLES EN EL INTERIOR. REMITIR TODO SERVICIO A UN TÉCNICO CALIFICADO
1. Lea detenidamente estas instrucciones antes de usar este artículo.
2. Guarde estas instrucciones para referencia futura.
3. Lea todas las advertencias.
4. Siga todas las instrucciones.
5. ADVERTENCIA: Para evitar incendios o descargas eléctricas, no exponga este equipo a la
lluvia ni a la humedad. No almacene ni opere este producto cerca de ningún líquido.
6. Limpie solo con un paño seco.
7. No almacene ni utilice este producto cerca de fuentes de calor, como radiadores, rejillas
de calefacción, estufas u otros aparatos (incluidos los amplificadores) que produzcan calor.
8. No anule el propósito de seguridad del enchufe polarizado o con conexión a tierra. Un
enchufe polarizado tiene dos clavijas, una más ancha que la otra. Un enchufe con conexión
a tierra tiene dos clavijas y una punta redonda con conexión a tierra. La hoja ancha o la
tercera punta se proporciona para su seguridad. Si el enchufe proporcionado no se ajusta a
su toma de corriente, consulte a un electricista para reemplazar la toma de corriente
obsoleta.
El símbolo del relámpago con punta de flecha dentro de un triángulo equilátero
pretende alertar al usuario sobre la presencia de "voltaje peligroso" dentro de la
carcasa del producto que puede ser de suficiente magnitud para constituir un
riesgo de descarga eléctrica para los humanos. Los usuarios deben mostrar mayor
seguridad cuando este símbolo aparece en este manual de instrucciones y siga
todas las precauciones tal como se indican.
El signo de exclamación dentro de un triángulo equilátero pretende alertar al
usuario de la presencia de importantes instrucciones de operación y mantenimien-
to (servicio) en este manual.
Missouri 2000 / 2500 / 3000
3 4
Federal Communications Commission Requirements
The equipment has been tested and found to comply with the limits for Class B Digital
Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction, may cause harmful interference to radio
communication. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
o Reorient of relocate the receiving antenna.
o Increase the separation between the equipment and receiver.
o Connect the equipment into an-outlet on a circuit different from that to which the
receiver is connected.
o Consult the dealer or an experienced radio/TV technician for help.
THE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE
FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT, FCC
Radiation Exposure Statement: The equipment complies with FCC radiation exposure limits
set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure
Guidelines in Supplement C to OET65. The equipment has very low levels of RF energy that it
is deemed to comply without testing of specific absorption ratio (SAR).
A: Microphone Head
B: Battery Indicator or display
C: Power & Silent Switch
D: Battery Case
E: Volume
Operating Instructions
The comes equipped with two wireless microphones and a receiver. The microphones
wirelessly transmit the signal to the receiver which receives the signal with the help of the
antennas on the rear of the unit.
Connect the antennas to the rear of the receiver and then insert the power cable. Lower
the volume so as not to damage your other audio devices. Then twist off the microphone
battery cover and insert the battery. Be sure to align the polarity of the battery to ensure it is
installed corrected.
Connect the 1/4" mixed audio output to the line or microphone input on your mixer, stereo
receiver or amplifier OR connect the XL output to a microphone input on one of those
devices.
Turn on the microphones and the receiver. The microphone's power indicator will illuminate.
Additionally, the microphone connection indicator on the receiver should illuminate as well.
Slowly raise the volume on the microphone receiver and your other audio devices and
begin to use the microphone.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS
1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND
2. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.
USER´S
MANUAL
MANUAL
DE USUARIO