Panasonic SCPM53 Manual de usuario

Marca: Panasonic

Modelo: SCPM53

Categoría: Reproductores de CD

Tipo: Manual de usuario

Operating Instructions

CD Stereo System

Model No. SC-PM53

SC-PM533

RQTV0097-2P

SC-PM533 is available in the U.S.A. only.

Before connecting, operating or adjusting this product, please

read the instructions completely.

Please keep this manual for future reference.

Operations in these instructions are described using remote

control, but you can do the operations with the main unit if the

controls are the same.

Unless otherwise indicated, illustrations in these operating

instructions are of SC-PM53 for the U.S.A. and Canada.

Your unit may not look exactly as illustrated.

La guía rápida en español se encuentra en la página 18 - 23.

The illustrations show SC-PM53.

PPC

Table of contents

IMPORTANT SAFETY

INSTRUCTIONS .................................. 3

Disc information ..................................... 3

Getting started ........................................ 4

Placement of speakers ........................... 5

Overview of controls .............................. 6

Discs ........................................................ 7

Cassette tape .......................................... 9

Radio ........................................................ 10

Timer ........................................................ 11

Sound adjustment .................................. 12

External unit ............................................ 13

Troubleshooting guide ........................... 14

Speciﬁ cations ......................................... 15

Maintenance ............................................ 15

When moving the unit ............................ 15

Limited Warranty

(ONLY FOR U.S.A.) ............................. 16

Limited Warranty

(ONLY FOR CANADA) ........................ 17

Product Service ...................................... 17

SUPPLIED ACCESSORIESSUPPLIED ACCESSORIES

Please check and identify the supplied accessories.

Use numbers indicated in parentheses when asking for

replacement parts. (As of December 2005)

In the U.S.A. to order accessories, refer to “Accessory

Purchases” on page 16.

1 x Remote control

(N2QAYB000008)

1 x AM loop antenna

(N1DAAAA00001)

1 x AC power supply cord

(K2CB2CB00018)

1 x FM indoor antenna

(RSA0007-L)

2 x Remote control batteries

EspañolEspañol

Preparativos iniciales ............................ 18

Colocación de los altavoces ................ 18

Controles ................................................ 19

Discos ..................................................... 20

Cintas de casete .................................... 21

Radio ....................................................... 22

Temporizador ......................................... 23

RQTV0097_2P_EN.indd 1RQTV0097_2P_EN.indd 1 2/6/06 3:33:54 PM2/6/06 3:33:54 PM

RQTV0097

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

dangerous voltage within the product s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE SCREWS.

NO USER-SERVICEABLE PARTS

INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Dear customer

Thank you for purchasing this product.

For optimum performance and safety, please read these

instructions carefully.

These operating instructions are applicable to the following

system.

System SC-PM53 SC-PM533

Main unit SA-PM53 SA-PM533

Speakers SB-PM53 SB-PM53

The model number and serial number of this product can

be found on either the back or the bottom of the unit.

Please note them in the space provided below and keep

for future reference.

MODEL NUMBER

SERIAL NUMBER

Except for U.S.A.

Inside of product

RQTV0097_2P_EN.indd 2RQTV0097_2P_EN.indd 2 2/6/06 3:34:01 PM2/6/06 3:34:01 PM

RQTV0097

ENGLISHEnglishEnglish

Disc information

• This unit can play MP3 or WMA ﬁ les and CD-DA format audio

CD-R/RWs that have been ﬁ nalized.

• It may not be able to play some CD-R/RWs depending on the

condition of the recording.

• Do not use irregularly shaped discs.

• Do not use discs with labels and stickers that are coming off or with

adhesive exuding from under labels and stickers.

• Do not attach extra labels or stickers on the disc.

• Do not write anything on the disc.

• This unit can access up to 99 tracks.

• Choose a disc with this mark:

Using DualDiscs

The “CD” sides of DualDiscs do not meet the CD-DA standard so it

may not be possible to play them on this unit.

MP3

WMA

• Files are treated as tracks and folders are treated as albums.

•

This unit can access up to 999 tracks, 255 albums and 20 sessions.

• Disc must conform to ISO9660 level 1 or 2 (except for extended

formats).

• To play in a certain order, preﬁ x the folder and ﬁ le names with the

3-digit numbers in the order you want to play them.

Not doing the following will cause damage to the unit.

Removing the power plug

• “GOODBYE” is displayed when the unit turns off. Remove the

power plug after this display disappears.

Tray caution

01&/$-04&

• Always press [OPEN/CLOSE 0] to insert or remove a disc.

• Do not push or pull out the tray by hand as this may cause an

accident.

Inserting a disc

• Place the disc label-up in the center or tray.

• Insert only one disc into each tray.

RQTV0097_2P_EN.indd 3RQTV0097_2P_EN.indd 3 2/6/06 3:34:04 PM2/6/06 3:34:04 PM

RQTV0097

Step Step 11

- Making the connections - Making the connections

Connect the AC power supply cord only after all other connections have been made.

Optional antenna connectionsOptional antenna connections

FM outdoor antenna AM outdoor antenna

FM ANT



AM ANT

EXT LOOP

FM outdoor antenna

(not included)

Ω coaxial cable

(not included)

FM ANT

75

AM ANT

EXT LOOP

AM outdoor antenna

(not included)

AM loop antenna

(included)

(16 - 40 ft.)

• Never use an outdoor antenna during a lightning storm.

• You can connect the FM outdoor antenna for better reception. Please consult your dealer for installation.

• Disconnect the FM indoor antenna if an FM outdoor antenna is installed.

• Connect the AM outdoor antenna without removing the AM loop antenna. Run 5 to 12 m (16 - 40 feet) of vinyl-covered wire

horizontally along a window or other convenient location.



HIGH



)

(6

)

Getting started

Connect the AC power supply cord.

The included AC power supply cord is for use with this

unit only. Do not use it with other equipment.

Connect the speaker cords.

Incorrect connection can damage the unit.

Red

Blue (·)

Black (·)

Red (ª)

Gray

(ª)

Gray

Blue

Black

FM ANT



AM ANT

EXT LOOP

Connect the FM indoor antenna.

Tape the antenna to a wall or column, in a

position with least amount of interference.

Adhesive

tape

FM indoor

antenna

Connect the AM loop antenna.

Stand the antenna up on its base. Keep the loose antenna cord

away from other wires and cords.

AM loop antenna

RQTV0097_2P_EN.indd 4RQTV0097_2P_EN.indd 4 2/6/06 3:34:10 PM2/6/06 3:34:10 PM

RQTV0097

ENGLISHEnglishEnglish

Step 2

- Inserting batteries into the remote control - Inserting batteries into the remote control

AA/R6/LR6

■ Batteries

• Insert so the poles (+ and –) match those in the remote control.

• Remove if the remote control is not going to be used for a long period of

time. Store in a cool, dark place.

• Do not use rechargeable type batteries.

• Mishandling of batteries in the remote control can cause electrolyte

leakage, which may cause a ﬁ re.

Do not:

• mix old and new batteries.

• use different types of batteries at the same time.

• heat or expose to ﬂ ame.

• take apart or short circuit.

• attempt to recharge alkaline or manganese batteries.

• use batteries if their covering has been peeled off.

■ Use

• Aim at the remote control sensor, avoiding obstacles, at a maximum

range of 7

m (23 feet) directly in front of the unit.

Refer to page 6 for remote control signal sensor position.

SStep 33

- DEMO function - DEMO function

When the unit is ﬁ rst plugged in, a demonstration of its functions may be

shown on the display.

If the demo setting is off, you can show a demonstration by selecting

“DEMO ON”.

Press and hold [–DEMO, 7].

The display changes each time the button is held down.

DEMO ONDEMO OFF

While in standby mode, select “DEMO OFF” to reduce power

consumption.

Placement of speakers

Speakers are designed identically so that no left or right channel orientation is necessary.

Use only the supplied speakers.

The combination of the main unit and speakers provide the best sound. Using other speakers can damage the unit and sound

quality will be negatively affected.

Note

• Keep your speakers at least 10mm (

˝) away from the system for proper ventilation.

• These speakers do not have magnetic shielding. Do not place them near televisions, personal computers or other devices easily inﬂ uenced

by magnetism.

• To avoid damage to the speakers, do not touch the speaker cones if you have taken the nets off.

Caution

• Use the speakers only with the recommended system. Failure to do so can damage the ampliﬁ er and

speakers, and can cause ﬁ re. Consult a qualiﬁ ed service person if damage occurs or if a sudden

change in performance is apparent.

• Do not attach these speakers to walls or ceilings.

RQTV0097_2P_EN.indd 5RQTV0097_2P_EN.indd 5 2/6/06 3:34:22 PM2/6/06 3:34:22 PM

RQTV0097

Overview of controls

Main unitMain unit

Refer to numbers in parentheses for page reference.

Cassette lid (9)

Remote control sensor

1 Standby/on switch (POWER y/l) (15)

Press to switch the unit from on to standby

mode or vice versa. In standby mode, the unit is

still consuming a small amount of power.

4 Bass selection (12)

Disc selection (7)

8 Tuner/Band selection (10)

Disc tray (7)

Headphone jack (

)

Avoid listening for prolonged

periods of time to prevent

hearing damage.

Plug type: 3.5

mm (

˝) stereo

(not included)

Cassette lid open (9)

Display panel

9 Volume control

7 Recording start/pause (9, 13)

2 Disc play/pause (7)

3 Tape play (9)

Changing disc (7)

6 Music port selection (13)

Top of unit

! H.BASS selection (13)

Checking disc position (8)

AC supply indicator (AC IN)

This indicator lights when the unit is connected

to the AC power supply.

Music port jack (13)

5 Treble selection (12)

Disc tray open/close (7)

Disc skip/search, tape fast-forward/

rewind, tune/preset channel selection,

time adjustment (9)

Stop/Demo (5, 9)

Remote controlRemote control

Buttons such as 1 function the same as the controls on the main unit.

Clock/Timer (11)

Play timer/Record timer (11)

Numeric (7, 10)

Delete (8)

Muting

Play mode (7, 9, 10)

Disc (7)

Program (8)

Clear (8)

Re-Master (13)

Sleep timer (11)

Preset EQ (12)

Disc skip/search, tape fast-

forward/rewind, tune/preset

channel selection, time

adjustment (7, 10, 11)

Repeat (8)

Treble/bass

adjustment (12)

Display (8)

Dimmer

Stop (7)

Surround (13)

Auto off

Album selection

(7)

Enter (8)

This function allows you to

turn off the unit in disc or

tape mode only after left

unused for 10 minutes.

The setting is maintained

even if the unit is turned

off.

Dims the display panel.

Mutes the sound.

• Press the button to activate.

• Press again to cancel.

RQTV0097_2P_EN.indd 6RQTV0097_2P_EN.indd 6 2/6/06 3:34:32 PM2/6/06 3:34:32 PM

RQTV0097

ENGLISHEnglishEnglish

Basic playBasic play

MP3

WMA

Press [y] to turn the unit on.

Press [1 3~ 5 3] to select your desired tray.

Press [OPEN/CLOSE 0] to open the disc tray and

then load the disc. Press [OPEN/CLOSE 0] again to

close the tray.

Disc tray

Label must

face upward

Tray number

Press [CD 6] to start play.

Adjust the volume.

To Action

stop the disc Press [STOP 7].

pause play Press [CD 6]. Press again to

resume play.

skip tracks Press

[4/REW/4] or [3/FF/¢]

during play or pause.

search through tracks

Press and hold [4/REW/4] or

[3/FF/¢] during play or pause.

direct play If the unit is on standby mode and a

disc is loaded, press [CD 6] or

[1 3 ~ 5 3] to start play.

skip album

MP3

WMA

Press [ALBUM or ] in the play

mode.

Press [ALBUM

or ] once and

then the numeric buttons in the stop

mode.

Changing disc (CD CHANGE)Changing disc (CD CHANGE)

MP3

WMA

While one disc is playing, you can change the discs in other

trays (except in All-Disc random play or program play).

Press [CHANGE 0].

Press [1 3~ 5 3] to select the tray.

Change the disc.

Press [CHANGE 0] again to close the tray.

Play Mode functionPlay Mode function

MP3

WMA

Press [CD 6] and then [STOP 7].

Press [DISC] and (within 10 seconds) press [1 ~ 5] to

select the disc.

Press [PLAY MODE] to select the desired mode.

Mode To play

1-DISC

1DISC

one selected disc.

ALL-DISC

ALL DISC

all discs in trays, e.g., 4→5→1→2→3.

1-TRACK

1TR

one selected track on the selected

disc.

Press the numeric buttons to select

the track.

1-ALBUM

1ALBUM

MP3

WMA

one selected album on the selected

disc.

Press [ALBUM

or ] to select

the album.

1-DISC RANDOM

1DISC RND

one selected disc randomly.

1-ALBUM RANDOM

1ALBUM RND

MP3

WMA

all tracks in one selected album

randomly.

Press [ALBUM

or ] to select

the album.

ALL-DISC RANDOM

ALL DISC RND

all loaded discs randomly.

Note

• During any random play, you cannot skip to tracks that have been

played.

•

During 1-DISC RANDOM or ALL-DISC RANDOM play, you can

search forward or backward only within the current track.

Discs

Disc trays

Numeric

buttons

RQTV0097_2P_EN.indd 7RQTV0097_2P_EN.indd 7 2/6/06 3:34:37 PM2/6/06 3:34:37 PM

RQTV0097

Discs (continued)

Checking which discs are in the trays (CD CHECK)Checking which discs are in the trays (CD CHECK)

MP3

WMA

Press [CD CHECK].

CD CHECK

Press the button again to close the trays.

Note

• The tray with a disc being played will not open.

• If the player is stopped, all trays will open.

• Do not remove or insert discs during disc check.

• Do not pull out the trays during disc check.

• 8 cm discs cannot be checked.

Display functionDisplay function

This function allows you to display the information of the

current track.

Press [DISPLAY] repeatedly during play or pause mode.

Elapsed time Remaining time

MP3

WMA

Elapsed time

Remaining

time

Album name Track name

Tag (Artist) Tag (Track) Tag (Album)

Note

• Maximum number of displayable characters: approximately 30

• This unit supports ver. 1.0 & 1.1 ID3 tags. Text data that is not

supported will not be displayed.

• ID3 is a tag embedded in MP3 tracks to provide information about

the track.

Advanced playAdvanced play

Direct access playDirect access play

This function allows you to start play from a speciﬁ c track.

Press the numeric buttons to select and play your

desired track.

MP3

WMA

Press [ALBUM or ] to select the album.

Press [3/FF/¢] once and then the numeric buttons

to select and play your desired track.

For two-digit track, press [

10] once, and then the two

digits.

For three-digit track, press [h10] twice, and then the three

digits.

Note

This function does not work during any random/program mode.

Repeat playRepeat play

You can repeat program play or other selected play mode.

MP3

WMA

Press [REPEAT] before or during play.

“REPEAT ON” and “ ” are displayed.

To cancel

Press [REPEAT] again.

“REPEAT OFF” is displayed and “

” is cleared.

Program playProgram play

This function allows you to program up to 24 tracks.

Press [CD 6] and then [STOP 7].

Press [PROGRAM].

Press [DISC].

(Within 10 seconds or so)

Press [1~5] to select your desired disc.

Press the numeric buttons to select your desired

track.

Repeat steps 3 to 5 to program other tracks.

Press [CD 6] to start play.

MP3

WMA

Press [CD 6] and then [STOP 7].

Press [DISC].

(Within 10 seconds or so)

Press [1~5] to select your desired disc.

Press [STOP 7].

Press [PROGRAM].

Press [ALBUM or ] to select your desired

album.

Press [3/FF/¢] once and then the numeric buttons

to select your desired track.

Press [ENTER].

Repeat steps 6 to 8 to program other tracks.

Press [CD 6] to start play.

To Action

cancel program mode Press [PROGRAM] in the stop mode.

replay the program Press [PROGRAM] then [CD 6].

check program

contents

Press [ /REW/4] or [ /FF/¢] when

“PGM” is displayed in the stop mode.

To check while programming, press

[PROGRAM] twice after “PGM” appears,

then press

[ /REW/4] or [ /FF/¢] .

add to the program

Repeat step 3 to 5 in the stop mode.

MP3

WMA

Repeat steps 6 to 8 in the stop mode.

clear the last track Press [DEL] in the stop mode.

clear all programmed

tracks

Press [CLEAR] in the stop mode. “CLR ALL”

is displayed.

Note

• When you try to program more than 24 tracks “PGM FULL”

appears.

• During program play, skipping is always in the programmed order,

whether forward or backward.

• You cannot program CD-DA together with MP3 and WMA tracks.

• You cannot change or open other trays during program play mode.

•

During program play, you can search backward or forward only

within the current track.

•

MP3

WMA

The program memory is cleared when you change a disc or open

a disc tray.

RQTV0097_2P_EN.indd 8RQTV0097_2P_EN.indd 8 2/6/06 3:34:43 PM2/6/06 3:34:43 PM

RQTV0097

ENGLISHEnglishEnglish

Cassette tape

Cassette lid

Top of unit

The buttons described for “Cassette tape” are mainly

for the main unit unless indicated otherwise.

Basic playBasic play

Press [0] and insert the cassette.

Insert inside

the guides

Forward side

Close the lid by hand.

Press [TAPE 3] to start play.

To play the other side of the cassette, turn the cassette over.

To Action

stop tape playback Press [–DEMO, 7].

start one-touch play Press [TAPE 3] when the unit is OFF with

the cassette loaded.

fast-forward and

rewind

Press

[4/REW/4] or [3/FF/¢] in the

stop mode.

Note

• Tapes exceeding 100 minutes are thin and can break or get caught

in the mechanism.

• Endless tapes can get caught up in the deckʼs moving parts if used

incorrectly.

TPS (Tape Program Sensor)TPS (Tape Program Sensor)

This function enables you to search the beginning of a track,

up to a maximum of 9.

Press

[4/REW/4] or [3/FF/¢] during play.

Play resumes from the track found.

Note

TPS may not function properly:

• with short silent parts

• when noise occurs between tunes

• if silent parts found within tunes

RecordingRecording

Use normal position tapes.

High position and metal position tapes can be used, but this

unit will not be able to record or erase them correctly.

Preparation

Wind the leader tape so that recording can begin

immediately.

Recording the radioRecording the radio

Insert the cassette to be recorded.

Tune to the required station (refer to page 10).

Press [¶ REC/8] to start recording.

Recording discsRecording discs

Insert the cassette to be recorded.

Press [CD 6] and then [–DEMO, 7].

Press [OPEN/CLOSE 0] to insert the disc. Press

again to close.

Press [PLAY MODE] on the remote control to select

your desired mode (refer to page 7).

Press [¶ REC/8] to start recording.

Recording programmed tracksRecording programmed tracks

Insert the cassette to be recorded.

Program the tracks you want (refer to page 8).

Press [¶ REC/8] to start recording.

Other basic operationsOther basic operations

To Action

erase a recorded

sound

1) Insert the cassette to be recorded.

2) Press [TAPE 3] and then [–DEMO, 7].

3) Press [¶ REC¥8].

stop recording Press [–DEMO, 7].

stop recording

temporarily

1) Press [¶ REC¥8].

2) Press again to resume recording.

record on the other

side of the tape

Turn the cassette over and press

[¶ REC¥8].

You can perform the same operation of [¶ REC¥8] on the

main unit by pressing [REC ¶¥8] and [TAPE] simultaneously

on the remote control.

Erasure preventionErasure prevention

The illustration shows how to remove the tabs to prevent

recording. To record on the tape again, cover as shown.

Side A

Tab for

side A

Tab for

side B

To re-record

Normal tape

Adhesive tape

RQTV0097_2P_EN.indd 9RQTV0097_2P_EN.indd 9 2/6/06 3:34:48 PM2/6/06 3:34:48 PM

RQTV0097

Radio

Numeric

buttons

Manual tuningManual tuning

Press [TUNER/BAND] to select “FM” or “AM”.

Press [PLAY MODE] to select “MANUAL”.

Press [4/REW/4] or [3/FF/¢] to select the

frequency of the required station.

“

ST ”

is displayed when a stereo FM broadcast is being

received.

To tune automatically

Press [4/REW/4] or [3/FF/¢] for a moment until the

frequency starts changing rapidly. The unit begins auto

tuning, stopping when it ﬁ nds a station.

• Auto tuning may not function when there is excessive

interference.

• To cancel auto tuning, press [4/REW/4], [3/FF/¢] or

[STOP 7].

To improve FM sound qualityTo improve FM sound quality

Press and hold [PLAY MODE] to display “MONO”.

To cancel

Press and hold [PLAY MODE] again until “MONO”

disappears.

• MONO is also canceled if the frequency is changed.

• Turn off “MONO” for normal listening.

Memory presetMemory preset

Up to 15 stations can be set in both the FM and AM bands.

Preparation

Press [TUNER/BAND] to select “FM” or “AM”.

Automatic presettingAutomatic presetting

Press and hold [PROGRAM] to start presetting.

Manual presettingManual presetting

Press [PLAY MODE] to select “MANUAL”.

Press [4/REW/4] or [3/FF/¢] to tune to the

required station.

Press [PROGRAM].

Press numeric buttons to select a channel.

The station occupying a channel is erased if another

station is preset in that channel.

Repeat steps 2 to 4 to preset more stations.

Selecting a preset stationSelecting a preset station

Press numeric buttons to select the channel.

For channels 10 to 15 press [

10], then the two digits.

Press [PLAY MODE] to select “PRESET”.

Press [4/REW/4] or [3/FF/¢] to select the

channel.

FM allocation settingFM allocation setting

By main unit only

This system can also receive FM broadcasts allocated in

0.1 MHz steps.

To change the step to 0.1 MHz

Press and hold [TUNER/BAND].

After a few seconds the display changes to a ﬂ ashing

display of the current minimum frequency.

Continue to hold down [TUNER/BAND].

• When the minimum frequency changes, release the

button. To return to the original step, repeat the above

steps.

• After the setting is changed, any previously preset

frequency will be cleared.

RQTV0097_2P_EN.indd 10RQTV0097_2P_EN.indd 10 2/6/06 3:34:55 PM2/6/06 3:34:55 PM

RQTV0097

ENGLISHEnglishEnglish

Timer

Setting the clockSetting the clock

This is a 12-hour clock.

Press [CLOCK/TIMER] to select “CLOCK”.

Each time you press the button:

CLOCK

˚ PLAY

Original display

˚ REC

Within 5 seconds, press [4/REW/4] or [3/FF/¢]

to set the time.

Press [CLOCK/TIMER] again to conﬁ rm.

Displaying the clock

Press [CLOCK/TIMER] to display the clock for a few

seconds.

Note

The clock may lose or gain minutes over a period of time. Readjust

as necessary.

Using the sleep timerUsing the sleep timer

This function enables you to turn off the unit automatically

after the set time.

Press [SLEEP] repeatedly to select your desired time.

30MIN 60MIN 90MIN 120MIN OFF

Sleep timer indicator

To cancel

Press [SLEEP] to select “OFF”.

Changing the remaining time

Press [SLEEP] to show the remaining time, and press

[SLEEP] again to select your desired time.

Note

• The play and sleep timer or the record and sleep timer can be used

together.

• The sleep timer always has priority. Be sure not to overlap timer

settings.

Using the play or record timerUsing the play or record timer

You can set the timer to come on at a certain time to wake

you up (play timer) or to record from the radio or a music port

source (record timer).

Preparation

Turn the unit on and set the clock.

Timer Action

Play timer Prepare the music source you want to listen

to; cassette, disc number (1-5), radio or

music port source, and set the volume.

Record timer Check the cassetteʼs erasure prevention

tabs (refer to page 9), insert the cassette and

tune to the radio station (refer to page 10) or

select music port source (refer to page 13).

Press [CLOCK/TIMER] repeatedly to select your

desired timer.

CLOCK

˚ PLAY

Original display

˚ REC

Within 5 seconds, press [4/REW/4] or [3/FF/¢]

to set the starting time.

Play timer indicator

Start time

Record timer indicator

Press [CLOCK/TIMER] to confirm.

Repeat steps 2 and 3 to set the finishing time.

Finish time

To activate the timer

Press [˚PLAY/REC] to turn on your desired timer.

˚ PLAY

no display (off)

˚ REC

Press [y] to turn off the unit.

The unit must be off for the timers to operate.

To enjoy the desired source after the timer setting is

completed.

The volume level (for play timer) and music source are stored

in the timer memory and the timer will start in these preset

conditions. However, the disc numbers do not get stored in

the timer memory.

1. After step 5, start playing the desired source.

2. Reset the disc numbers if you have changed any of them,

conﬁ rm that a disc or cassette is inserted, then press [y]

to put the unit on standby.

RQTV0097_2P_EN.indd 11RQTV0097_2P_EN.indd 11 2/6/06 3:34:59 PM2/6/06 3:34:59 PM

RQTV0097

Timer (Continued)

Other basic operationsOther basic operations

To Action

change the settings Repeat steps 1 to 4 and 6 on page 11.

change the source

or volume

1) Press [

˚PLAY/REC] to clear the timer

indicator from the display.

2) Make changes to the source or volume.

3) Perform steps 5 and 6 on page 11.

check the settings

(when the unit is on

or in standby mode)

Press [CLOCK/TIMER] repeatedly to

select

˚PLAY or ˚REC.

cancel Press [˚PLAY/REC] to clear the timer

indicators from the display.

Note

• The play timer and record timer cannot be used together.

• The play timer will start at the preset time, with the volume

increasing gradually to the preset level.

• The record timer will start 30 seconds before the set time with the

volume muted.

• The timer comes on at the set time every day if the timer is on.

• The unit must be in the standby mode for the timer to function.

• If you turn the unit off and on again while a timer is functioning, the

ﬁ nish time setting will not be activated.

• If MUSIC PORT is selected as the source when the timer comes on,

the system turns on and engages MUSIC PORT as the source. If

you wish to playback or record from the portable audio equipment,

activate the equipmentʼs play mode and increase the volume. (See

the portable audio equipmentʼs instruction manual.)

Sound adjustment

Selecting sound effectsSelecting sound effects

You can change the sound effect by selecting Preset EQ or

adjusting the bass or treble effect.

Preset EQPreset EQ

Press [PRESET EQ] repeatedly to select your desired

setting.

HEAVY

→

CLEAR

→

SOFT

→

VOCAL

→

EQ-OFF

Setting Effect

HEAVY Adds punch to rock

CLEAR Clariﬁ es higher frequencies

SOFT For background music

VOCAL Adds gloss to vocal

EQ-OFF No effect

Bass or trebleBass or treble

Enable you to enjoy the lower or higher pitch sound.

Press [BASS] or [TREBLE] to select your desired

setting.

Setting Effect

BASS For lower pitch sound

TREBLE For higher pitch sound

Press [5] or [∞] to adjust the level.

To adjust bass or treble using the main unit.

Turn [BASS] or [TREBLE] clockwise to increase the

level.

Turn [BASS] or [TREBLE] counter-clockwise to decrease

the level.

Note

The tone level can be varied within -3 to +3.

RQTV0097_2P_EN.indd 12RQTV0097_2P_EN.indd 12 2/6/06 3:35:04 PM2/6/06 3:35:04 PM

RQTV0097

ENGLISHEnglishEnglish

External unit

The buttons described for “External unit” are mainly for

the main unit unless indicated otherwise.

Connecting to a portable audio Connecting to a portable audio equipmentequipment

This feature enables you to enjoy music from portable audio

equipment.

Portable audio equipment

(not included)

Audio cord (not included)

MUSIC

PORT

jack

Playing from portable audio equipmentPlaying from portable audio equipment

Switch off the equalizer function (if there is any) of the

portable audio equipment before you plug into the MUSIC

PORT jack. Otherwise, sound from the speaker may be

distorted.

Plug the audio cord into the MUSIC PORT jack and

press [MUSIC P.].

Play the portable audio equipment. (See the portable

audio equipment’s instruction manual.)

Recording from portable audio Recording from portable audio equipmentequipment

Insert the cassette to be recorded.

Press [MUSIC P.].

Play the portable audio equipment.

Press [¶ REC¥8] to start recording.

Note

• All peripheral components and cables are sold separately.

• For other recording operations, refer page 9, “Other basic

operations”.

Enjoying surround soundEnjoying surround sound

Enable you to add natural width and depth to the stereo

sound.

To activate

Press [SURROUND] to display “

” indicator.

To cancel

Press [SURROUND] again to clear “

” indicator.

Note

• Surround sound is less discernible when listening through

headphones.

• If interference in FM stereo reception increases, cancel the

surround sound effect.

Enhancing the bassEnhancing the bass

Enable you to enjoy the powerful bass effect.

Press [H.BASS] repeatedly to select your desired

setting.

LEVEL 1

→

LEVEL 2

→

OFF

Note

The actual effect depends on the disc.

Re-master – Enjoying more natural soundRe-master – Enjoying more natural sound

Discs recorded at:

MP3

32 kHz, 44.1 kHz or 48 kHz

WMA

22 kHz, 32 kHz, 44 kHz or 48 kHz

This feature reproduces the frequencies lost during recording

to give you a sound closer to the original.

Press [RE-MASTER] during play to select “RE-MASTER

ON”.

Each time you press the button:

RE-MASTER ON ↔ RE-MASTER OFF

Note

You cannot change RE-MASTER during recording.

RQTV0097_2P_EN.indd 13RQTV0097_2P_EN.indd 13 2/6/06 3:35:09 PM2/6/06 3:35:09 PM

RQTV0097

Troubleshooting guide

Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the

remedies indicated in the chart do not solve the problem, refer to the “Customer Services Directory” on page 16 if

you reside in the U.S.A., or refer to the “Product information” on page 17 if you reside in Canada.

Common problems

No sound.

Turn the volume up.

The speaker cords may not be connected properly. Turn the unit off, check and correct the

connections and turn the unit on (refer to page 4).

Sound is unﬁ xed, reversed or comes

from one speaker only.

Check the speaker connections (refer to page 4).

Humming heard during play.

An AC power supply cord or ﬂ uorescent light is near the cables. Keep other appliances and

cords away from this unitʼs cables.

“ERROR” is displayed.

Incorrect operation performed. Read the instructions and try again.

“– –:– –” appears on the display.

You plugged the AC power supply cord in for the ﬁ rst time or there was a power failure

recently.

Set the time (refer to page 11).

“F61” is displayed.

Check and correct the speaker cord connections (refer to page 4). Unplug and plug in the

AC power supply cord, then turn on the unit.

If this does not ﬁ x the problem, there is a power supply problem. Consult the dealer.

Listening to the radio

Noise is heard.

The stereo indicator ﬂ ickers or doesn’t

light.

Sound is distorted.

Use an outdoor antenna (refer to page 4).

A beat sound is heard.

Turn the TV off or separate it from the unit.

A low hum is heard during AM

broadcast.

Separate the antenna from other cables and cords.

When there is a television set nearby

The picture on the TV

disappears or stripes appear

on the screen.

The location and direction of the antenna are incorrect. If you are using an indoor antenna,

change to an outdoor antenna (refer to page 4).

The TV antenna wire is too close to the unit. Separate the antenna wire of the TV set from

the unit.

Using the cassette deck

Recording is not possible.

If the erasure prevention tabs have been removed, cover the holes with adhesive tape (refer

to page 9).

Playing discs

The display is wrong or play

won’t start.

The disc may be upside down (refer to page 3).

Wipe the disc.

Replace the disc if it is scratched, warped, or non-standard.

Condensation may have formed inside the unit due to a sudden change in temperature. Wait

about an hour for it to clear and try again.

The total number of tracks displayed

differs each time the same disc is

inserted.

Unusual sound is heard.

The disc may be scratched, or its data may be defective. Replace the disc.

CD-RW cannot be read.

The disc was incompletely formatted. Use the recording equipment to fully format the disc

before recording.

“VBR–” is displayed instead of the

remaining play time.

The unit cannot display the remaining play time for variable bit rate (VBR) tracks.

“TAKE OUT/DISC” appears on the

display.

There is a problem with the disc mechanism. (A power failure may have occurred.)

The tray will open automatically. Remove the disc from the tray, and after ensuring there is

no disc in the tray, close it. The unit will make the disc changing noises for a few moments

and then it should operate normally.

The remote control

Remote control doesn’t work.

Check that the batteries are inserted correctly (refer to page 5).

Replace the batteries if they are worn.

RQTV0097_2P_EN.indd 14RQTV0097_2P_EN.indd 14 2/6/06 3:35:12 PM2/6/06 3:35:12 PM

RQTV0097

ENGLISHEnglishEnglish

Speciﬁ cations

AMPLIFIER SECTION

FTC OUTPUT POWER both channel driven

simultaneously

10% Total harmonic distortion

Hz to 3

kHz

(Low channel)

SC-PM53

W per channel (6

Ω)

SC-PM533

W per channel (6

Ω)

kHz to 16

kHz

(High channel)

SC-PM53

W per channel (6

Ω)

SC-PM533

W per channel (6

Ω)

Total Bi-Amp power

SC-PM53

W per channel

SC-PM533

W per channel

RMS OUTPUT POWER both channel driven

simultaneously

10% total harmonic distortion

kHz

(Low channel)

SC-PM53

W per channel (6

Ω)

SC-PM533

W per channel (6

Ω)

kHz

(High channel)

SC-PM53

W per channel (6

Ω)

SC-PM533

W per channel (6

Ω)

Total Bi-Amp power

SC-PM53

W per channel

SC-PM533

W per channel

Input Impedance

Music port 250 mV 12 kΩ

Output Impedance

Headphone 16

Ω to 32

Phone jack

Terminal Stereo, 3.5 mm (

Music port input jack

Terminal Stereo, 3.5 mm (

FM TUNER SECTION

Frequency range

87.9

MHz to 107.9

MHz (200

kHz steps)

87.5

MHz to 108.0

MHz (100

kHz steps)

Sensitivity 0.3

µV (IHF)

S/N 26

dB 0.2

µV

Antenna terminals 75

Ω (unbalanced)

Preset station FM 15 stations

AM 15 stations

AM TUNER SECTION

Frequency range 520 kHz to 1710

kHz (10

kHz steps)

Sensitivity

S/N 20

dB (at 1000

kHz) 900

µV/m

CASSETTE DECK SECTION

Track system 4-track, 2-channel

Heads

Record/playback Solid permalloy head

Erasure Double gap ferrite head

Motor DC servo motor

Recording system AC bias 100

kHz

Erase system AC erase 100

kHz

Tape speed 4.8

cm/s (1

ips)

Overall frequency response (+3, –6

dB at DECK OUT)

NORMAL 35

Hz to 14

kHz

S/N RATIO 54

dB (A weighted)

Wow and ﬂ utter 0.08% (WRMS)

Fast-forward and rewind time

Approx. 120 seconds with C-60 cassette tape

CD SECTION

Disc played [8 cm (3") or 12 cm (5")]

(1) CD-Audio (CD-DA)

(2) CD-R/RW (CD-DA, MP3, WMA formatted disc)

(3) MP3/WMA

Sampling frequency

CD-DA 44.1

kHz

MP3/WMA 32

kHz, 44.1

kHz, 48

kHz

Bit rate

MP3/WMA 32

kbps to 384

kbps

Decoding 16/20/24 bit linear

Pick up

Wavelength 785 nm

Beam source Semiconductor laser

Laser power CLASS 1

Audio output (Disc)

Number of channels 2-Channel

Frequency response 20

Hz to 20

kHz

(+1dB, -2

dB)

Wow and ﬂ utter Below measurable limit

Digital ﬁ lter 8

D/A converter MASH (1 bit DAC)

SPEAKER SECTION

Type 2 way, 2 speaker system

Speaker(s)

Woofer 10cm (4˝) cone type (6

Ω)

Tweeter 6

cm (2

˝) cone type (6

Ω)

Impedance 6

Input power (IEC)

HIGH 90

W (Max)

LOW 90

W (Max)

Output sound pressure 80

dB/W (1.0 m)

Crossover over frequency 2.2 kHz

Frequency range 45

Hz to 35

kHz (-16

dB)

Hz to 31

kHz (-10

dB)

Dimensions (W x H x D) 144

mm x 249

mm x 200

˝ x 9

˝ x 7

˝)

Mass 1.9

kg (4.2

lb.)

GENERAL

Power supply AC 120

V, 60

Power consumption 140

Dimensions (W x H x D) 175

mm x 249

mm x 355

˝ x 9

˝ x 13

˝)

Mass 5.4

kg (11.9

lb.)

Operating temperature range

+5°C to +35°C (+41°F to +95°F)

Operating humidity range

5% to 90% RH (no condensation)

Power consumption in standby mode 0.4

Note

1. Speciﬁ cations are subject to change without notice.

Mass and dimensions are approximate.

2. Total harmonic distortion is measured by the digital spectrum

analyzer.

3. The labels “HIGH” and “LOW” on the rear or the speakers refer to

High frequency and Low frequency.

Maintenance

If the surfaces are dirtyIf the surfaces are dirty

To clean this unit, wipe with a soft, dry cloth.

• Never use alcohol, paint thinner or benzine to clean this

unit.

• Before using chemically treated cloth, read the instructions

that came with the cloth carefully.

For a cleaner, crisper soundFor a cleaner, crisper sound

Clean the heads regularly to assure good quality playback

and recording.

Use a cleaning tape (not included).

When moving the unit

Remove all discs.

Press [POWER y/I] to turn the unit off.

Disconnect the AC power supply cord.

RQTV0097_2P_EN.indd 15RQTV0097_2P_EN.indd 15 2/6/06 3:35:15 PM2/6/06 3:35:15 PM

RQTV0097

Limited Warranty (ONLY FOR U.S.A.)

Panasonic Audio Products

Limited Warranty

Panasonic Consumer Electronics Company,

Division of Panasonic Corporation of North America

One Panasonic Way Secaucus, New Jersey 07094

Panasonic Puerto Rico, Inc.

Ave. 65 de Infantería, Km. 9.5

San Gabriel Industrial Park, Carolina, Puerto Rico 00985

Limited Warranty Coverage

If your product does not work properly because of a defect in materials or

workmanship, Panasonic Consumer Electronics Company or Panasonic Puerto

Rico, Inc. (collectively referred to as “the warrantor”) will, for the length of

the period indicated on the chart below, which starts with the date of original

purchase (“warranty period”), at its option either (a) repair your product with new

or refurbished parts, or (b) replace it with a new or a refurbished product. The

decision to repair or replace will be made by the warrantor.

During the “Labor” warranty period there will be no charge for labor. During the

“Parts” warranty period, there will be no charge for parts. You must carry-in or

mail-in your product during the warranty period. If non-rechargeable batteries

are included, they are not warranted. This warranty only applies to products

purchased and serviced in the United States or Puerto Rico. This warranty is

extended only to the original purchaser of a new product which was not sold “as

is”. A purchase receipt or other proof of the original purchase date is required

for warranty service.

Carry-In or Mail-In Service

For Carry-In or Mail-In Service in the United States call 1-800-211-PANA (1-800-

211-7262) or visit Panasonic web site: http://www.panasonic.com

For assistance in Puerto Rico call Panasonic Puerto Rico, Inc. (787)-750-4300

or fax (787)-768-2910.

Limited Warranty Limits And Exclusions

This warranty ONLY COVERS failures due to defects in materials or workmanship,

and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty

ALSO DOES NOT COVER damages which occurred in shipment, or failures which

are caused by products not supplied by the warrantor, or failures which result from

accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty

installation, set-up adjustments, misadjustment of consumer controls, improper

maintenance, power line surge, lightning damage, modiﬁ cation, or commercial

use (such as in a hotel, ofﬁ ce, restaurant, or other business), rental use of the

product, service by anyone other than a Factory Servicenter or other Authorized

Servicer, or damage that is attributable to acts of God.

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER

“LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE

FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM

THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS

WARRANTY. (As examples, this excludes damages for lost time, travel to and from

the servicer, loss of media or images, data or other memory content. The items

listed are not exclusive, but are for illustration only.) ALL EXPRESS AND IMPLIED

WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE

LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential

damages, or limitations on how long an implied warranty lasts, so the exclusions

may not apply to you.

This warranty gives you speciﬁ c legal rights and you may also have other rights

which vary from state to state. If a problem with this product develops during or

after the warranty period, you may contact your dealer or Servicenter. If the problem

is not handled to your satisfaction, then write to the warrantorʼs Consumer Affairs

Department at the addresses listed for the warrantor.

PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED

WARRANTY ARE YOUR RESPONSIBILITY.

Product or Part Name Parts Labor

Audio Products (except items listed

below)

One (1) year One (1) year

USB Reader-Writer, Personal

Computer Card Adapters

(in exchange for defective item)

One (1) year Not Applicable

Accessories: Headphones,

Cartridges, Microphones, Adapters

Ninety (90)

days

Ninety (90)

days

Rechargeable Batteries, DVD-R/-RAM

Discs (in exchange for defective item)

Ten (10) days Not Applicable

SD Memory Cards, Rechargeable

Battery Packs (in exchange for

defective item)

Ninety (90)

days

Not Applicable

Obtain Product Information and Operating Assistance; locate your nearest Dealer or Servicenter; purchase Parts and

Accessories; or make Customer Service and Literature requests by visiting our Web Site at:

http://www.panasonic.com/comsumersupport

or, contact us via the web at:

http://www.panasonic.com/contactinfo

You may also contact us directly at:

1-800-211-PANA (7262),

Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.

For hearing or speech impaired TTY users, TTY: 1-877-833-8855

Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at:

http://www.pasc.panasonic.com

or, send your request by E-mail to:

[email protected]

You may also contact us directly at:

1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday-Friday 9 am to 8 pm, EST.)

Panasonic Services Company

20421 84th Avenue South, Kent, WA 98032

(We Accept Visa, MasterCard, Discover Card, American Express, and Personal Checks)

For hearing or speech impaired TTY users, TTY: 1-866-605-1277

Panasonic Puerto Rico, Inc.

Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985

Phone (787)750-4300, Fax (787)768-2910

Accessory PurchasesAccessory Purchases

Service in Puerto RicoService in Puerto Rico

Customer Services DirectoryCustomer Services Directory

RQTV0097_2P_EN.indd 16RQTV0097_2P_EN.indd 16 2/6/06 3:35:20 PM2/6/06 3:35:20 PM

RQTV0097

ENGLISHEnglishEnglish

Limited Warranty (ONLY FOR CANADA)

Panasonic Canada Inc.

PANASONIC/TECHNICS PRODUCT – LIMITED WARRANTY

Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship and agrees to remedy

any such defect for a period as stated below from the date of original purchase.

Technics Audio Product One (1) year, parts and labour

Panasonic Audio & DVD Product One (1) year, parts and labour

Accessories including rechargeable batteries Ninety (90) days

In-home Service will be carried out only to locations accessible by roads and within 50 km of an authorized Panasonic

service facility.

LIMITATIONS AND EXCLUSIONS

This warranty does not apply to products purchased outside Canada or to any product which has been improperly installed,

subjected to usage for which the product was not designed, misused or abused, damaged during shipping, or which has

been altered or repaired in any way that affects the reliability or detracts from the performance, nor does it cover any product

which is used commercially. Dry cell batteries are also excluded from coverage under this warranty.

This warranty is extended to the original end user purchaser only. A purchase receipt or other proof of date of original

purchase is required before warranty service is performed.

THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL

DAMAGES.

In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or

the exclusion of implied warranties, so the above limitations and exclusions may not be applicable.

WARRANTY SERVICE

FOR PRODUCT OPERATION ASSISTANCE, please contact:

Our Customer Care Centre:

Telephone #: (905) 624-5505

1-800 #: 1-800-561-5505

Fax #: (905) 238-2360

Email link: “Contact Us” on www.panasonic.ca

FOR PRODUCT REPAIRS, please locate your nearest Authorized Servicente at www.panasonic.ca:

Link: “Servicentres

locator” under “Customer support”

Panasonic Factory Service:

Richmond British Columbia Mississauga, Ontario

Panasonic Canada Inc.

12111 Riverside Way

Richmond BC V6W 1K8

Tel: (604) 278-4211

Fax: (604) 278-5627

Panasonic Canada Inc.

5770 Ambler Drive

Mississauga ON L4W 2T3

Tel: (905) 624-8447

Fax: (905) 238-2418

IF YOU SHIP THE PRODUCT TO A SERVICENTRE

Carefully pack and send prepaid, adequately insured and preferably in the original carton.

Include details of the defect claimed, and proof of date of original purchase.

1. Damage requiring service — The unit should be serviced by qualiﬁ ed service personnel if:

(a) The AC power supply cord or the plug has been damaged; or

(b) Objects or liquids have gotten into the unit; or

(d) The unit does not operate normally or exhibits a marked change in performance; or

(e) The unit has been dropped or the cabinet damaged.

2. Servicing— Do not attempt to service the unit beyond that described in these operating instructions. Refer all other

servicing to authorized servicing personnel.

3. Replacement parts— When parts need replacing ensure the servicer uses parts speciﬁ ed by the manufacturer or parts

that have the same characteristics as the original parts. Unauthorized substitutes may result in ﬁ re, electric shock, or

other hazards.

4. Safety check— After repairs or service, ask the servicer to perform safety checks to conﬁ rm that the unit is in proper

working condition.

The servicer will require all components to service your system.

Therefore, should service ever be necessary, be sure to bring the entire system.

Product information

For product information or assistance with product operation:

In the U.S.A., refer to “Customer Services Directory” on page 16.

In Canada, contact the Panasonic Canada Inc. Customer Care Centre at 905-624-5505, or visit the website (www.panasonic.ca),

or an authorized Servicentre closest to you.

Product Service

RQTV0097_2P_EN.indd 17RQTV0097_2P_EN.indd 17 2/6/06 3:35:25 PM2/6/06 3:35:25 PM

RQTV0097



HIG



)

(6

)

Preparativos iniciales

Conecte el cable de alimentación de CA

El cable de alimentación de CA incluido es para ser

usado con este aparato solamente. No lo utilice con

otro equipo.

Conecte los cables de los altavoces.

Una conexión incorrecta puede dañar el aparato.

Rojo

Azul (·)

Negro (·)

Rojo (ª)

Gris

(ª)

Gris

Azul

Negro

FM ANT

75

AM ANT

EXT LOOP

Conecte la antena interior de FM.

Fije la antena en una pared o columna en una

posición en que las señales de radio se reciban

con la menor interferencia.

Cinta

adhesiva

Antena interior

de FM

Conecte la antena de cuadro de AM.

Ponga la antena en posición vertical sobre su base.

PasoPaso 11

- Conexiones - Conexiones

Conecte el cable de alimentación de CA sólo después de haber hecho todas las demás conexiones.

PasoPaso 2 2

- Introducción de pilas en el - Introducción de pilas en el

mando a distanciamando a distancia

■ Pilas

• Inserte los polos (+ y –) de la forma que se indica en el

mando a distancia.

• Retire las pilas si no va a utilizar el mando a distancia

durante un periodo de tiempo largo. Guárdelas en un

lugar fresco y oscuro.

• No utilice baterías recargables.

• Un mal manejo de pilas en el control remoto puede

provocar fugas electrolíticas, que pueden provocar fuego.

■ Utilización

• Diríjalo al sensor del mando a distancia, evitando los

obstáculos, desde una distancia máxima de 7 m (23 pies)

directamente frente al aparato.

Consulte la página 6 para ver la posición del sensor de la

señal del mando a distancia.

PasoPaso 33

- Función de demostración - Función de demostración

Cuando el aparato se enchufe por primera vez puede

aparecer en el visualizador una demostración de sus

funciones.

Si el ajuste de demostración está desactivado, usted podrá

activarlo seleccionando “DEMO ON”.

Mantenga pulsado [–DEMO, 7] en la unidad principal.

La visualización cambia cada vez que se pulsa el botón.

DEMO OFF

(desactivación)

DEMO ON

(activación)

Durante el modo de espera, seleccione “NO DEMO” para

reducir el consumo de energía.

Colocación de los altavoces

Los altavoces han sido diseñados identicamente por lo que no es necesario orientar el canal derecho o izquiedo.

Utilice solamente los altavoces suministrados.

La combinación de la unidad principal y los altavoces proporciona el mejor sonido. Utilizando otros altavoces se puede

estropear la unidad y el sonido quedará afectado negativamente.

Nota

• Mantenga sus altavoces alejados un mínimo de 10mm (

˝) del sistema para disponer de una ventilación apropiada.

• Estos altavoces no disponen de blindaje magnético. No los ponga cerca de televisores, ordenadores personales y otros dispositivos a los

que afecte fácilmente el magnetismo.

• Para evitar estropear los altavoces, no toque los conos de los altavoces si ha quitado las redes.

Precaución

• Use los altavoces sólo con el sistema recomendado. De lo contrario, se podrían dañar el ampliﬁ cador

y los altavoces, y se podría ocasionar un incendio. Consulte a un técnico de servicio especializado si

se ha producido algún daño o si se ha producido un cambio repentino en su funcionamiento.

• No instale estos altavoces en paredes ni techos.

RQTV0097_2P_ES.indd 18RQTV0097_2P_ES.indd 18 2/6/06 3:38:10 PM2/6/06 3:38:10 PM

RQTV0097

ESPAÑOL EnglishEnglish

Controles

Aparato principalAparato principal

Los números entre paréntesis indican la página de referencia.

Soporte de casete (21)

Sensor de señal del mando a

distancia

1 Interruptor de alimentación en espera/

conectada (POWER y/l) (15)

Pulse este interruptor para cambiar del modo de

alimentación conectada al modo de alimentación

en espera o viceversa. En el modo de

alimentación en espera el aparato consume una

pequeña cantidad de corriente.

4 Selección de graves (12)

Selección de CD (7)

8 Selector de sintonizador/

banda (22)

Bandeja de disco (20)

Toma de auriculares (

)

Procure evitar utilizarlos mucho

rato con el ﬁ n de evitar lesiones

auditivas.

Tipo de clavija: estéreo de

3.5

mm (

˝)

(no suministrada)

Abra la tapa del disco (21)

Visualizador

9 Control de volumen

7 Grabación (13, 21)

2 Reproducción/pausa de disco (20)

3 Reproducción de la cinta (21)

Cambiador de CD (7)

6 Selección de puerto de

música (13)

Parte superior del aparato

! Selección H.BASS (13)

Comprobación de posición

de CD (8)

Indicador de alimentación de CA (AC IN)

Este indicador se encenderá cuando el aparato

esté conectado a la red de CA.

Conector de puerto de música (13)

5 Selección de agudos (12)

Abrir/cerrar bandeja de disco (20)

Omitir/buscar disco, avance rápido de cinta/

rebobinar, sintonizar/selección de canal

presintonizado (21)

Paro/demostración (18, 21)

Mando a distanciaMando a distancia

Los botones como el 1 funcionan del mismo modo que los botones del aparato principal.

Reloj/temporizador (23)

Temporizadorde

reproducción/grabación (23)

Numerados (20, 22)

Borrado (8)

Silenciamiento

Selector del modo de

reproducción (20 a 22)

Disco (20)

Programas (8)

Cancelación de

programas (8)

Re-Master (13)

Temporizador

para dormir (11)

Ecualizador preajustado (12)

Omitir/buscar disco, avance

rápido de cinta/rebobinar,

sintonizar/selección de canal

presintonizado (20, 22, 23)

Repetición (8)

Ajuste de

graves/agudos

(12)

Visualizador (8)

Reducción de la iluminación

del visualizador

Parada (20)

Sonido envolvente (13)

Apagado

automático

Selección de

àlbum (20)

Introducir (8)

Esta función de apagado

automático le permite

apagar el aparato en

modo disco o cinta, sólo

después de 10 minutos sin

utilizarlo.

El ajuste se mantiene

aunque el aparato esté

apagado.

Reduce la iluminación del

visualizador.

Silencia el sonido.

• Pulse el botón para activarlo.

• Vuélvalo a pulsar para cancelar.

RQTV0097_2P_ES.indd 19RQTV0097_2P_ES.indd 19 2/6/06 3:38:37 PM2/6/06 3:38:37 PM

RQTV0097

Reproducción básicaReproducción básica

MP3

WMA

Pulse [y] para encender el aparato.

Pulse [1 3~ 5 3] para seleccionar la bandeja

deseada.

Pulse [OPEN/CLOSE 0] para abrir la bandeja del

disco y cargar un CD. Vuelva a pulsar [OPEN/CLOSE

0] para cerrar la bandeja.

Bandeja de disco

La etiqueta

tiene que estar

hacia arriba

Número de

bandeja

Pulse [CD 6] para iniciar la reproducción.

Ajuste el volumen.

Para Acción

detener el disco Pulse [STOP 7].

interrumpir la

reproducción

Pulse [CD 6]. Vuelva a pulsar para

reanudar la reproducción.

saltar pistas Pulse

[4/REW/4] o [3/FF/¢]

durante la reproducción

o la pausa.

buscar por pistas

Mantenga pulsado [4/REW/4] o

[3/FF/¢] durante la reproducción

o la pausa.

iniciar la reproducción

con un toque

Si el aparato está en modo de espera

y se introduce un disco compacto,

pulse [CD 6] o [1 3 ~ 5 3] para

iniciar la reproducción.

saltar álbum

MP3

WMA

Pulse [ALBUM o ] en el modo

de reproducción.

Pulse [ALBUM

or ] una vez y

los botones numéricos en el modo

de parada.

Función de modo de reproducciónFunción de modo de reproducción

MP3

WMA

Pulse [CD 6] y después [STOP 7].

Pulse [DISC] y (antes de que pasen 10 segundos)

pulse [1 ~ 5] para seleccionar el disco.

Pulse [PLAY MODE] en el mando a distancia para

seleccionar el modo deseado.

Modo Para reproducir

1-DISC

1DISC

un disco seleccionado.

ALL-DISC

ALL DISC

todos los discos de las bandejas,

p. ej., 4→5→1→2→3.

1-TRACK

1TR

una melodía seleccionada del disco

seleccionado.

Pulse las teclas numéricas para

seleccionar la pista.

1-ALBUM

1ALBUM

MP3

WMA

un disco seleccionado aleatoriamente.

Pulse [ALBUM

or ] para

seleccionar el álbum.

1-DISC RANDOM

1DISC RND

todos los discos cargados en orden

aleatorio.

1-ALBUM RANDOM

1ALBUM RND

MP3

WMA

un álbum seleccionado del disco

seleccionado.

Pulse [ALBUM

or ] para

seleccionar el álbum.

ALL-DISC RANDOM

ALL DISC RND

todos los discos cargados en orden

aleatorio.

Note

• Durante cualquier reproducción aleatoria, no puede saltar pistas

que ya han sido reproducidas.

•

Durante la reproducción RANDOM de 1 CD o de TODOS LOS

CDʼs, podrá buscar hacia delante sólo en la pista actual.

Discos

Bandeja de

disco

Botones

numéricos

RQTV0097_2P_ES.indd 20RQTV0097_2P_ES.indd 20 2/6/06 3:38:46 PM2/6/06 3:38:46 PM

RQTV0097

ESPAÑOL EnglishEnglish

Cintas de casete

Soporte de casete

Parte superior del

aparato

Los botones descritos para “Cintas de casete” son

principalmente para la unidad a no ser que se indique

lo contrario.

Reproducción básicaReproducción básica

Pulse [0] e insertar la cinta.

Introduzca

dentro de las

guías

Lado de avance

Cierre la tapa con la mano.

Pulse [TAPE 3] para iniciar la reproducción.

Para reproducir la otra cara de la cinta, dé la vuelta al casete.

Para Acción

detener la

reproducción

Pulse [–DEMO, 7].

iniciar la

reproducción con

un toque

Pulse [TAPE 3] cuando el sistema esté

apagado con el casete cargado.

avanzar

rápidamente o

rebobinar

Pulse

[4/REW/4] o [3/FF/¢] el modo

de parada.

GrabaciónGrabación

Use cintas de posición normal.

Pueden usarse cintas de posición alta y de metal, pero el

aparato no las grabará ni las borrará correctamente.

Preparación

Rebobine la cinta original para que la grabación pueda

comenzar de inmediato.

Grabación de discosGrabación de discos

Introduzca el casete en el que quiera grabar.

Pulse [CD 6] y luego [–DEMO, 7].

Pulse [OPEN/CLOSE 0] para introducir el CD. Vuélvalo

a pulsar para cerrar.

Pulse [PLAY MODE] en el mando a distancia para

seleccionar el modo deseado (consulte la página 20).

Pulse [¶ REC/8] para iniciar la grabación.

Other basic operationsOther basic operations

Para Acción

detener la grabación Pulse [–DEMO, 7].

grabar en la otra cara

de la cinta

Dé la vuelta a la cinta de casete y pulse

[¶ REC¥8].

Puede realizar la misma operación de [¶ REC¥8] en la unidad

principal, pulsando [REC ¶¥8] y [TAPE] simultáneamente en

el mando a distancia.

RQTV0097_2P_ES.indd 21RQTV0097_2P_ES.indd 21 2/6/06 3:39:01 PM2/6/06 3:39:01 PM

RQTV0097

Radio

Botones

numéricos

Sintonización manualSintonización manual

Pulse [TUNER/BAND] para seleccionar “FM” o

“AM”.

Pulse [PLAY MODE] para seleccionar “MANUAL”.

Pulse [4/REW/4] o [3/FF/¢] para seleccionar la

frecuencia de la emisora requerida.

Se visualizará “

ST ”

cuando esté siendo recibida una

emisora estéreo por FM.

Para sintonizar automáticamente

Pulse

[4/REW/4] o [3/FF/¢] hasta que la frecuencia

empiece a cambiar rápidamente. El aparato inicia la

sintonización automática y se detendrá cuando encuentre

una emisora.

• La sintonización automática tal vez se interrumpa cuando

las interferencias sean excesivas.

• Para cancelar la sintonización automática, pulse [4/

REW/4], [3/FF/¢] ó [STOP 7].

Para mejorar la calidad del sonido de FMPara mejorar la calidad del sonido de FM

Mantenga pulsado [PLAY MODE] para visualizar

“MONO”.

Para cancelar

Pulse y mantenga pulsado [PLAY MODE] otra vez hasta

que“MONO” desaparezca.

• MONO también se cancelará si se cambia la frecuencia.

• Deje “MONO” apagado para la escucha normal.

Grabación de emisoras en memoriaGrabación de emisoras en memoria

Se puede presintonizar un máximo de 15 emisoras en cada

banda, FM y AM.

Preparación

Pulse [TUNER/BAND] para seleccionar “FM” o “AM”.

Presintonización automáticaPresintonización automática

Mantenga pulsado [PROGRAM] para iniciar la

presintonización.

Presintonización manualPresintonización manual

Pulse [PLAY MODE] para seleccionar “MANUAL”.

Pulse [4/REW/4] o [3/FF/¢] para seleccionar la

emisora deseada.

Pulse [PROGRAM].

Pulse los botones numéricos para seleccionar el

canal.

La emisora que ocupa un canal se borrará si se

presintoniza otra emisora en ese canal.

Repita los pasos del 2 al 4 para preestablecer más

emisoras.

Selec Selección de ción deSelec Selección de ción de

Pulse los botónes numéricos para seleccionar el canal.

Para los canales 10 a 15 pulse [

10] y luego los dos

dígitos.

Pulse [PLAY MODE] para seleccionar “PRESET”.

Pulse [4/REW/4] o [3/FF/¢] para seleccionar el

canal.

Ajuste de la asignación de FMAjuste de la asignación de FM

Aparato principal solamente

Este sistema le permite recibir emisiones de FM asignadas

en pasos de 0,1 MHz.

Para cambiar el paso a 0,1 MHz

Mantenga pulsado [TUNER/BAND].

Después de unos segundos, la visualización cambiará a

una visualización parpadeante de la frecuencia mínima

actual.

Continúe pulsando [TUNER/BAND].

• Si la frecuencia mínima cambia, suelte el botón. Para

volver al paso original, repita los pasos anteriores.

• Después de cambiar el ajuste de “asignación”, las

frecuencias previamente preajustadas en la memoria

se borrarán.

RQTV0097_2P_ES.indd 22RQTV0097_2P_ES.indd 22 2/6/06 3:39:08 PM2/6/06 3:39:08 PM

RQTV0097

ESPAÑOL EnglishEnglish

Temporizador

Puesta en horaPuesta en hora

Éste es un reloj de sistema de 12 horas.

Pulse [CLOCK/TIMER] para seleccionar “CLOCK”.

Cada vez que pulse el botón:

CLOCK

˚ PLAY

Visulización original

˚ REC

Entre 5 segundos, Pulse [4/REW/4] o [3/FF/¢]

para ajustar la hora.

Pulse [CLOCK/TIMER] para terminar de poner la

hora.

Visualización del reloj

Pulse [CLOCK/TIMER] para visualizar el reloj durante unos

segundos.

Nota

El reloj puede atrasar o adelantar minutos, pasado un plazo de

tiempo. Si es necesario, vuelva a ponerlo en hora.

Utilización del temporizador de Utilización del temporizador de

reproducción/grabaciónreproducción/grabación

Puede ajustar el temporizador para que se encienda a

una hora determinada para despertarle (temporizador de

reproducción) o para grabar la radio o fuente de puerto de

música (temporizador de grabación).

Preparación

Encienda el aparato y ponga en hora el reloj.

Temporizador Acción

Temporizador de

reproducción

Prepare la fuente musical que desee

escuchar: cinta, número de disco (1-5), radio

o fuente de puerto de musica y ajuste el

volumen.

Temporizador de

grabación

Compruebe las lengüetas de prevención de

borrado del casete (consulte la página 9),

inserte el casete y sintonice la emisora de

radio (consulte la página 22) o seleccione

la fuente de puerto de musica (consulte la

página 13).

Pulse [CLOCK/TIMER] repetidamente para

seleccionar el temporizador deseado.

CLOCK

˚ PLAY

Visulización original

˚ REC

Entre 5 segundos, pulse [4/REW/4] o [3/FF/¢]

para ajustar la hora de inicio.

Indicador del temporizador

de reproducción

Hora de inicio

Indicador del temporizador de

grabación

Pulse [CLOCK/TIMER] para confirmar.

Repita los pasos 2 y 3 para ajustar la hora de

finalización.

Hora de ﬁ nalización

Para activar el temporizador

Pulse [˚PLAY/REC] para encender el temporizador

deseado.

˚ PLAY

Ninguna visualización

(desactivado)

˚ REC

Pulse [y] para apagar el aparato.

El aparato debe estar apagado para que funcionen los

temporizadores.

Otras operaciones básicas Otras operaciones básicasOtras operaciones básicas Otras operaciones básicas

Para Acción

cambiar la conﬁ

guración

Repita los pasos 1 a 4 y 6.

cambiar la fuente o

el volumen

1) Pulse [˚PLAY/REC] para cancelar el

temporizador indicador del visualizador.

2) Cambie la fuente o el volumen.

3) Realice los pasos 5 y 6.

compruebe la conﬁ

guración

Pulse [CLOCK/TIMER] repetidamente

seleccione

˚PLAY o ˚REC.

cancelar Pulse [˚PLAY/REC] para cancelar el

temporizador indicadores del visualizador.

Nota

• El temporizador de reproducción no puede utilizarse en combinación

con el temporizador de grabación.

• El temporizador de reproducción se pondrá en marcha a la hora

programada y el volumen aumentará gradualmente hasta el nivel

seleccionado.

• El temporizador de grabación de registro comenzará 30 segundos

antes del tiempo del sistema con el volumen silenciado.

• Si el temporizador está activo, se encenderá todos los días a la

hora ﬁ jada.

• El aparato debe estar en modo de espera para que el temporizador

funcione.

• Si apaga el aparato y lo vuelve a encender mientras esté

funcionando un temporizador, no se activará el ajuste de tiempo de

terminación.

• Si se selecciona el puerto música (MUSIC PORT) como fuente

cuando el temporizador avance, el sistema se enciende y utilice el

puerto de música (MUSIC PORT) como fuente. Si desea reproducir

o grabar desde el equipo reproductor portátil de audio, solo ha de

activar el modo reproducir del equipo reproductor y aumente el

volumen. (Ver el manual de instrucciones del reproductor portátil

de audio.)

RQTV0097_2P_ES.indd 23RQTV0097_2P_ES.indd 23 2/6/06 3:39:18 PM2/6/06 3:39:18 PM

Panasonic Consumer Electronics

Company, Division of Panasonic

Corporation of North America

One Panasonic Way Secaucus,

New Jersey 07094

http://www.panasonic.com

Panasonic Puerto Rico, Inc.

Ave. 65 de Infantería, Km. 9.5

San Gabriel Industrial Park, Carolina,

Puerto Rico 00985

Printed in Malaysia

Panasonic Canada Inc.

5770 Ambler Drive

Mississauga, Ontario,

L4W 2T3

www.panasonic.ca

RQTV0097-2P

L1205YS2026

En Sp

%34

RQTV0097_2P_ES.indd 24RQTV0097_2P_ES.indd 24 2/6/06 3:39:30 PM2/6/06 3:39:30 PM

Panasonic SCPM53 Manual de usuario

Marca: Panasonic

Modelo: SCPM53

Categoría: Reproductores de CD

Tipo: Manual de usuario

Descargar PDF

informe

en otros idiomas

English: Panasonic SCPM53 User manual

Panasonic SCPM53 Manual de usuario

Panasonic SCPM53 Manual de usuario

en otros idiomas

Artículos relacionados

Otros documentos