Titan GPX1600 El manual del propietario

Marca: Titan

Modelo: GPX1600

Categoría: Rociador de pintura

Tipo: El manual del propietario

Printed in the U. S. A.

GPX 1600

Gas Piston Pump

SprayTECH

1770 Fernbrook Lane

Minneapolis, MN 55447

Technical Assistance: 1-800-292-4637

Order Entry: 1-800-443-4500

Fax: 1-800-525-9501

www.spraytechinc.com

Owner’s Manual

Model Number 0509003

Table of Contents

Safety Precautions.................................................................2

Français ..............................................................................18

Español...............................................................................20

General Description ...............................................................4

Operation ................................................................................4

Setup ....................................................................................4

Preparing to Paint.................................................................4

Painting.................................................................................5

Pressure Relief Procedure ...................................................6

Spraying ..................................................................................6

Spraying Technique ..............................................................6

Practice.................................................................................6

Cleanup ...................................................................................7

Maintenance............................................................................7

General Repair and Service Notes.......................................7

Maintaining the Engine .........................................................8

Replacing the Filter...............................................................8

Replacing the PRIME/SPRAY Valve.....................................8

Replacing the Potentiometer ................................................9

Replacing the Pump ON/OFF Switch...................................9

Replacing the Transducer...................................................10

Replacing the Electronic Pressure Control (EPC) Board ...10

Replacing the Slider Assembly and Slider Housing............11

Replacing the Gears...........................................................12

Servicing the Clutch Assembly ...........................................12

Servicing the Fluid Section.................................................14

Troubleshooting ...................................................................17

Parts Listings........................................................................22

Main Assembly....................................................................22

Drive Assembly...................................................................23

Fluid Section Assembly ......................................................24

Cart Assembly.....................................................................25

Filter Assembly ...................................................................25

PRIME/SPRAY Assembly...................................................26

Electrical Schematic ...........................................................26

Labels .................................................................................26

Limited Warranty ..................................................................28

Safety Precautions

This manual contains information that must be read and

understood before using the equipment. When you come to an

area that has one of the following symbols, pay particular

attention and make certain to heed the safeguard.

This symbol indicates a potential hazard that may cause

serious injury or loss of life. Important safety information will

follow.

This symbol indicates a potential hazard to you or to the

equipment. Important information that tells how to prevent

damage to the equipment or how to avoid causes of minor

injuries will follow.

HAZARD: Injection injury - A high pressure stream

produced by this equipment can pierce the

skin and underlying tissues, leading to serious

injury and possible amputation. See a

physician immediately.

DO NOT TREAT AN INJECTION INJURY AS A SIMPLE

CUT! Injection can lead to amputation. See a physician

immediately.

The maximum operating range of the gun is 3300 PSI /

22.8 MPa fluid pressure.

WARNING

NOTE: Notes give important information which should

be given special attention.

CAUTION

WARNING

PREVENTION:

• NEVER aim the gun at any part of the body.

•NEVER allow any part of the body to touch the fluid stream.

DO NOT allow body to touch a leak in the fluid hose.

• NEVER put your hand in front of the gun. Gloves will not

provide protection against an injection injury.

•ALWAYS lock the gun trigger, shut the pump off, and release

all pressure before servicing, cleaning the tip or guard,

changing tip, or leaving unattended. Pressure will not be

released by turning off the motor. The PRIME/SPRAY knob

must be turned to PRIME to relieve the pressure. Refer to

the PRESSURE RELIEF PRESSURE described in the pump

manual.

•ALWAYS keep the tip guard in place while spraying. The

tip guard provides some protection but is mainly a warning

device.

•ALWAYS remove the spray tip before flushing or cleaning

the system.

• The paint hose can develop leaks from wear, kinking and

abuse. A leak can inject material into the skin. Inspect

the hose before each use.

•NEVER use a spray gun without a trigger lock and trigger

guard in place and in good working order.

• All accessories must be rated at or above 3300 PSI / 22.8

MPa. This includes spray tips, guns, extensions, and

hose.

HAZARD: EXPLOSION OR FIRE - Solvent and paint fumes

can explode or ignite. Severe injury and/or

property damage can occur.

PREVENTION:

• Provide extensive exhaust and fresh air introduction to

keep the air within the spray area free from accumulation

of flammable vapors.

•Avoid all ignition sources such as static electric sparks,

open flames, pilot lights, and hot objects. Connecting or

disconnecting power cords or working light switches can

make sparks.

•Do not smoke in spray area.

• Fire extinguisher must be present and in good working

order.

• Place paint pump in a well ventilated area. Flammable

vapors are often heavier than air. Floor area must be

extremely well ventilated. The paint pump contains arcing

parts that emit spark and can ignite vapors.

• The equipment and objects in and around the spray area

must be properly grounded to prevent static sparks.

• Use only conductive or grounded high pressure fluid hose.

Gun must be grounded through hose connections.

• Power cord must be connected to a grounded circuit

(electric models only).

• Always flush unit into a separate metal container, at low

pump pressure, with spray tip removed. Hold gun firmly

against side of container to ground container and prevent

static sparks.

• Follow the material and solvent manufacturer's warnings

and instructions.

• Use extreme caution when using materials with a

flashpoint below 70° F (21° C). Flashpoint is the

temperature that a fluid can produce enough vapors to

ignite.

• Plastic can cause static sparks. Never hang plastic to

enclose a spray area. Do not use plastic drop cloths

when spraying flammable materials.

• Use lowest possible pressure to flush equipment.

NOTE TO PHYSICIAN:

Injection into the skin is a traumatic injury. It is

important to treat the injury as soon as possible. DO

NOT delay treatment to research toxicity. Toxicity is a

concern with some coatings injected directly into the

blood stream. Consultation with a plastic surgeon or

reconstructive hand surgeon may be advisable.

GAS ENGINE (WHERE APPLICABLE)

Always place pump outside of structure in fresh air. Keep all

solvents away from the engine exhaust. Never fill fuel tank

with a running or hot engine. Hot surface can ignite spilled

fuel. Always attach ground wire from pump unit to a grounded

object, such as a metal water pipe. Refer to engine owner’s

manual for complete safety information.

HAZARD: EXPLOSION HAZARD DUE TO INCOMPATIBLE

MATERIALS - Will cause severe injury or

property damage.

PREVENTION:

• Do not use materials containing bleach or chlorine.

• Do not use halogenated hydrocarbon solvents such as

mildewcide, methylene chloride and 1,1,1 -

trichloroethane. They are not compatible with aluminum.

• Contact your coating supplier about the compatibility of

material with aluminum.

HAZARD: HAZARDOUS VAPORS - Paints, solvents,

insecticides, and other materials can be

harmful if inhaled or come in contact with the

body. Vapors can cause severe nausea,

fainting, or poisoning.

PREVENTION:

• Use a respirator or mask if vapors can be inhaled. Read

all instructions supplied with the mask to be sure it will

provide the necessary protection.

•Wear protective eyewear.

•Wear protective clothing as required by coating

manufacturer.

HAZARD: GENERAL - This product can cause severe

injury or property damage.

PREVENTION:

• Read all instructions and safety precautions before

operating equipment.

• Always disconnect the motor from the power supply

before working on the equipment (electric models only).

• Follow all appropriate local, state, and national codes

governing ventilation, fire prevention, and operation.

• The United States Government Safety Standards have

been adopted under the Occupational Safety and Health

Act (OSHA). These standards, particularly part 1910 of

the General Standards and part 1926 of the Construction

Standards should be consulted.

• Use only manufacturer authorized parts. User assumes

all risks and liabilities when using parts that do not meet

the minimum specifications and safety devices of the

pump manufacturer.

• Before each use, check all hoses for cuts, leaks, abrasion

or bulging of cover. Check for damage or movement of

couplings. Immediately replace the hose if any of these

conditions exist. Never repair a paint hose. Replace it

with another grounded high-pressure hose.

• All hoses, swivels, guns, and accessories must be rated at

or above 3300 PSI/22.8 MPa.

• Do not spray outdoors on windy days.

•Wear clothing to keep paint off skin and hair.

• Always unplug cord from outlet before working on

equipment.

• Do not use this equipment to spray water or acid.

Do not lift by cart handle when loading or unloading.

CAUTION

Gasoline Engine Safety

The engine exhaust from this unit contains chemicals

known to the State of California to cause cancer, birth

defects, or other reproductive harm.

1. Gas engines are designed to give safe and dependable

service if operated according to instructions. Read and

understand the engine Owner's Manual before operating

the engine. Failure to do so could result in personal injury

or equipment damage.

2. To prevent fire hazards and to provide adequate

ventilation, keep the engine at least 1 meter (3 feet) away

from buildings and other equipment during operation. Do

not place flammable objects close to the engine.

3. Children and pets must be kept away from the area of

operation due to a possibility of burns from hot engine

components or injury from any equipment the engine may

be used to operate.

4. Know how to stop the engine quickly, and understand the

operation of all controls. Never permit anyone to operate

the engine without proper instructions.

5. Gasoline is extremely flammable and is explosive under

certain conditions.

6. Refuel in a well-ventilated area with the engine stopped.

Do not smoke or allow flames or sparks in the refueling

area or where gasoline is stored.

7. Do not overfill the fuel tank. After refueling, make sure the

tank cap is closed properly and securely.

8. Be careful not to spill fuel when refueling. Fuel vapor or

spilled fuel may ignite. If any fuel is spilled, make sure the

area is dry before starting the engine.

9. Never run the engine in an enclosed or confined area.

Exhaust contains poisonous carbon monoxide gas;

exposure may cause loss of consciousness and may lead

to death.

10. The muffler becomes very hot during operation and

remains hot for a while after stopping the engine. Be

careful not to touch the muffler while it is hot. To avoid

severe burns or fire hazards, let the engine cool before

transporting it or storing it indoors.

11. Never ship/transport unit with gasoline in the tank.

WARNING

General Description

This airless sprayer is a precision power tool used for spraying

many types of materials. Read and follow this instruction

manual carefully for proper operating instructions,

maintenance, and safety information.

Operation

This equipment produces a fluid stream at extremely high

pressure. Read and understand the warnings in the

Safety Precautions section at the front of this manual

before operating this equipment.

Setup

Perform the following procedure before starting the engine of a

gas-powered sprayer.

1. Ensure that the siphon tube and the return hose are

attached and secure.

2. Attach the supplied grounding cable to a grounded object.

3. Using a wrench, attach a minimum of 50’ of 3/8” nylon

airless spray hose to the 3/8” outlet fitting on the filter

assembly. Tighten securely.

4. Attach an airless spray gun to the spray hose. Using two

wrenches (one on the gun and one on the hose), tighten

securely.

Make sure all airless hoses and spray guns are electrically

grounded and rated for at least 3300 psi (22.8 MPa) fluid

pressure.

5. Turn the pressure control knob fully counterclockwise to

its lowest pressure setting.

6. Make sure the pump ON/OFF switch is in the OFF position.

7. Fill the fluid section oil cup with approximately one

tablespoon of separating oil (P/N 0279920).

Never operate unit for more than ten seconds without

fluid. Operating this unit without fluid will cause

unnecessary wear to the packings.

CAUTION

WARNING

NOTE: Do not attach the tip to the spray gun yet.

Remove the tip if it is already attached.

NOTE: USE 3/8” SPRAY HOSE FOR MAXIMUM

PERFORMANCE, MINIMUM PRESSURE DROP,

AND MINIMUM PRESSURE FLUCTUATION.

WARNING

Engine

Pressure Control

Knob

Pail Hook

Fluid Section

Siphon Tube

Cart

Filter

Assembly

PRIME/SPRAY

Valve

3/8" Outlet Fitting

8. Check the engine oil level. The gasoline engine oil level

is determined by the manufacturer. Refer to the engine

manufacturer's service manual (supplied).

9. Close the fuel shut-off lever and fill the gas tank with

gasoline. Use only high quality, unleaded gasoline.

Preparing a New Sprayer

If this unit is new, it is shipped with test fluid in the fluid section

to prevent corrosion during shipment and storage. This fluid

must be thoroughly cleaned out of the system with mineral

spirits before you begin spraying.

Always keep the trigger lock on the spray gun in the

locked position while preparing the system.

1. Place the siphon tube into a container of mineral spirits

that has a flash point of 60ºC (140ºF) or above.

2. Place the return hose into a metal waste container.

3. Turn the pressure control knob fully counterclockwise to

its lowest pressure setting.

4. Move the PRIME/SPRAY valve to the PRIME position.

5. Move the engine ON/OFF switch to the ON position.

6. Start the engine:

a. Open the fuel valve

lever.

b. Move the throttle

lever away from the

gas tank.

c. Close the engine

choke lever.

d. Holding the frame

with one hand, pull

the starter rope

rapidly and firmly. Continue to hold the rope as you let it

return. Pull and return the rope until the engine starts.

7. Turn on the sprayer by moving

the pump ON/OFF switch to the

ON position.

8. Slowly turn the pressure control

knob clockwise to increase the

pressure until fluid starts to

come out of the return hose.

Use only enough pressure to

keep the fluid coming out.

9. Allow the sprayer to run for

15–30 seconds to flush the test fluid out through the

return hose and into the waste container.

10. Turn the pressure control knob fully counterclockwise to

its lowest setting.

11.Turn off the sprayer by moving the pump ON/OFF switch

to the OFF position.

Preparing to Paint

Before painting, it is important to make sure that the fluid in the

system is compatible with the paint that is going to be used.

Always keep the trigger lock on the spray gun in the

locked position while preparing the system.

1. Place the siphon tube into a container of the appropriate

solvent for the material being sprayed (refer to

recommendations of the material manufacturer). An

example of the appropriate solvent is water for latex paint.

2. Place the return hose into a metal waste container.

3. Turn the pressure control knob fully counterclockwise to

its lowest pressure setting.

CAUTION

NOTE: Incompatible fluids and paint may cause the

valves to become stuck closed, which would

require disassembly and cleaning of the

sprayer’s fluid section.

Pressure

Control

Knob

Pump

ON/OFF

Switch

Fuel Valve

Lever

Choke Lever

Engine

ON/OFF

Switch

Throttle

Lever

Starter Rope

CAUTION

4. Move the PRIME/SPRAY valve to the PRIME position.

5. Move the engine ON/OFF switch to the ON position.

6. Start the engine:

a. Open the fuel valve lever.

b. Move the throttle lever away from the gas tank.

c. Close the engine choke lever.

d. Holding the frame with one hand, pull the starter rope

rapidly and firmly. Continue to hold the rope as you let

it return. Pull and return the rope until the engine

starts.

7. Turn on the sprayer by moving the pump ON/OFF switch

to the ON position.

8. Slowly turn the pressure control knob clockwise to

increase the pressure until fluid starts to come out of the

return hose. Use only enough pressure to keep the fluid

coming out.

9. Allow the sprayer to run for 15–30 seconds to flush the old

solvent out through the return hose and into the metal

waste container.

10. Turn the pressure control knob fully counterclockwise to

its lowest setting.

11.Turn off the sprayer by moving the pump ON/OFF switch

to the OFF position.

12. Move the PRIME/SPRAY valve to the SPRAY position.

13. Turn on the sprayer.

14. Turn the pressure control knob slowly clockwise to

increase pressure.

15. Unlock the gun by turning the gun trigger lock to the

unlocked position.

Ground the gun by holding it against the

edge of the metal container while

flushing. Failure to do so may lead to a

static electric discharge, which may

cause a fire.

16. Trigger the gun into the metal waste

container until the old solvent is gone

and fresh solvent is coming out of the gun.

17. Lock the gun by turning the gun trigger lock to the locked

position.

18. Set down the gun and increase the pressure by turning

the pressure control knob slowly clockwise to its highest

setting.

19. Check the entire system for leaks. If leaks occur, turn the

sprayer off and follow the “Pressure Relief Procedure” in

this manual before tightening any fittings or hoses.

20. Follow the “Pressure Relief Procedure” in this manual

before changing from solvent to paint.

Be sure to follow the pressure relief procedure when

shutting the unit down for any purpose, including

servicing or adjusting any part of the spray system,

changing or cleaning spray tips, or preparing for cleanup.

Painting

1. Place the siphon tube into a container of paint.

2. Place the return hose into a metal waste container.

3. Turn the pressure control knob fully counterclockwise to

its lowest pressure setting.

4. Move the PRIME/SPRAY valve to the PRIME position.

5. Move the engine ON/OFF switch to the ON position.

6. Start the engine:

a. Open the fuel valve lever.

WARNING

NOTE: Make sure that the spray gun does not have a

tip or tip guard installed.

b. Move the throttle lever away from the gas tank.

c. Close the engine

choke lever.

d. Holding the frame

with one hand, pull

the starter rope

rapidly and firmly.

Continue to hold

the rope as you let

it return. Pull and

return the rope until

the engine starts.

7. Turn on the sprayer

by moving the pump ON/OFF switch to the ON position.

8. Slowly turn the pressure control

knob clockwise to increase the

pressure until fluid starts to

come out of the return hose.

Use only enough pressure to

keep the fluid coming out.

9. Allow the sprayer to run until

paint is coming through the

return hose into the metal

waste container.

10. Turn the pressure control knob fully counterclockwise to

its lowest setting.

11.Turn off the sprayer by moving the pump ON/OFF switch

to the OFF position.

12. Remove the return hose from the waste container and place

it in its operating position above the container of paint.

13. Move the PRIME/SPRAY valve to the SPRAY position.

14. Turn on the sprayer.

15. Turn the pressure control knob slowly clockwise to

increase pressure.

16. Unlock the gun by turning the gun trigger lock to the

unlocked position.

Ground the gun by holding it against the

edge of the metal container while

flushing. Failure to do so may lead to a

static electric discharge, which may

cause a fire.

17. Trigger the gun into the metal waste

container until all air and solvent is flushed from the spray

hose and paint is flowing freely from the gun.

18. Lock the gun by turning the gun trigger lock to the locked

position.

19. Turn the pressure control knob fully counterclockwise to

its lowest setting.

20. Turn off the sprayer.

21. Attach tip guard and tip to the gun as instructed by the tip

guard or tip manuals.

POSSIBLE INJECTION HAZARD. Do not spray without the

tip guard in place. Never trigger the gun unless the tip is in

either the spray or the unclog position. Always engage the

gun trigger lock before removing, replacing or cleaning tip.

22. Turn on the sprayer.

23. Increase the pressure by turning the pressure control

knob slowly clockwise and test the spray pattern on a

piece of cardboard. Adjust the pressure control knob until

the spray from the gun is completely atomized. Try to

keep the pressure control knob at the lowest setting that

maintains good atomization.

NOTE: Turning the pressure up higher then needed to

atomize the paint will cause premature tip wear

and additional overspray.

WARNING

Pressure

Control

Knob

Pump

ON/OFF

Switch

Fuel Valve

Lever

Choke Lever

Engine

ON/OFF

Switch

Throttle

Lever

Starter Rope

Pressure Relief Procedure

Be sure to follow the pressure relief procedure when

shutting the unit down for any purpose, including

servicing or adjusting any part of the spray system,

changing or cleaning spray tips, or preparing for cleanup.

1. Lock the gun by turning the gun trigger lock to the locked

position.

2. Turn off the sprayer by moving the pump ON/OFF switch

to the OFF position.

3. Turn off the engine by moving the engine ON/OFF switch

to the OFF position.

4. Turn the pressure control knob counterclockwise to its

lowest setting.

5. Unlock the gun by turning the gun trigger lock to the

unlocked position.

4. Hold the metal part of the gun firmly to

the side of a metal container to ground

the gun and avoid a build up of static

electricity.

5. Trigger the gun to remove any pressure

that may still be in the hose.

6. Lock the gun by turning the gun trigger lock to the locked

position.

7. Move the PRIME/SPRAY valve to the PRIME position.

Spraying

Spraying Technique

The key to a good paint job is an even coating over the entire

surface. This is done by using even strokes. Keep your arm

moving at a constant speed and keep the spray gun at a

constant distance from the surface. The best spraying distance

is 10 to 12 inches between the spray tip and the surface.

Keep the spray gun at right angles to the surface. This means

moving your entire arm back and forth rather than just flexing

your wrist.

Heavy Coat

Do not flex wrist while spraying.

Light Coat Light Coat

Keep stroke smooth and at an even speed.

Even coat throughout

Approximately

10 to 12 inches

NOTE: When spraying block filler, mastics or high

solid coating, remove the gun filter and high

pressure filter screens.

WARNING

Keep the spray gun perpendicular to the surface, otherwise

one end of the pattern will be thicker than the other.

The spray gun should be triggered by turning it on and off with

each stroke. This will save paint and avoid paint buildup at the

end of the stroke. Do not trigger the gun during the middle of

a stroke. This will result in an uneven spray and splotchy

coverage.

Overlap each stroke by about 30%. This will ensure an even

coating.

When you stop painting, lock the gun trigger lock, turn the

pressure control knob counterclockwise to its lowest setting

and set the PRIME/SPRAY valve to PRIME. Turn the motor

switch to OFF and unplug the sprayer.

Practice

1. Be sure that the paint hose is free of kinks and clear of

objects with sharp cutting edges.

2. Turn the pressure control knob counterclockwise to its to

its lowest setting.

3. Move the PRIME/SPRAY valve to the SPRAY position.

4. Turn the pressure control knob clockwise to its highest

setting. The paint hose should stiffen as paint begins to

flow through it.

5. Unlock the gun trigger lock.

6. Trigger the spray gun to bleed air out of the hose.

7. When paint reaches the spray tip, spray a test area to

check the spray pattern.

8. Use the lowest pressure

setting necessary to get a

good spray pattern. If the

pressure is set too high, the

spray pattern will be too light.

If the pressure is set too low,

tailing will appear or the paint

will spatter out in gobs rather

than in a fine spray.

Good spray pattern

Paint tailing pattern

Proper way to trigger the spray gun

Approximately

10 to 12 inches

Keep stroke

even

Start stroke End strokePull trigger Release triggerKeep steady

Approximately

10 to 12 inches

Right way

Wrong way

Cleanup

Special cleanup instructions for use with flammable

solvents:

•Always flush spray gun preferably outside and at least one

hose length from spray pump.

• If collecting flushed solvents in a one gallon metal

container, place it into an empty five gallon container, then

flush solvents.

• Area must be free of flammable vapors.

• Follow all cleanup instructions.

The sprayer, hose, and gun should be cleaned thoroughly

after daily use. Failure to do so permits material to build

up, seriously affecting the performance of the unit.

Always spray at minimum pressure with the gun nozzle tip

removed when using mineral spirits or any other solvent

to clean the sprayer, hose, or gun. Static electricity

buildup may result in a fire or explosion in the presence of

flammable vapors.

1. Follow the “Pressure Relief Procedure” found in the

Operation section of this manual.

2. Remove the gun tip and tip guard and clean with a brush

using the appropriate solvent.

3. Place the siphon tube into a container of the appropriate

solvent (refer to recommendations of the material

manufacturer). An example of the appropriate solvent is

water for latex paint.

4. Place the return hose into a metal waste container.

5. Move the PRIME/SPRAY valve to its PRIME position.

6. Move the engine ON/OFF switch to the ON position and

start the engine.

7. Turn on the sprayer by moving the pump ON/OFF switch

to the ON position.

8. Slowly turn the pressure control knob clockwise to increase

the pressure until fluid starts to come out of the return hose.

9. Allow the solvent to circulate through the sprayer and

flush the paint out of the return hose into the metal waste

container.

10. Turn the pressure control knob fully counterclockwise to

its lowest setting.

11.Turn off the sprayer by moving the ON/OFF switch to the

OFF position.

12. Move the PRIME/SPRAY valve to its SPRAY position.

13. Turn on the sprayer.

14. Turn the pressure control knob slowly clockwise to

increase pressure.

Ground the gun by holding it against the

edge of the metal container while

flushing. Failure to do so may lead to a

static electric discharge, which may cause

a fire.

15. Trigger the gun into the metal waste

container until the paint is flushed out of the hose and

solvent is coming out of the gun.

16. Continue to trigger the spray gun into the waste container

until the solvent coming out of the gun is clean.

NOTE: For long-term or cold weather storage, pump

mineral sprits through the entire system.

WARNING

CAUTION

WARNING

17. Follow the “Pressure Relief Procedure” found in the

Operation section of this manual.

18. Store the sprayer in a clean, dry area.

Do not store the sprayer under pressure.

Cleaning the Spray Tip

1. Flush the gun with solvent immediately after the work is

completed.

2. Oil the sliding pins to prevent them from seizing up.

Should the spray tip become clogged, reverse

the spray tip with the lever and pull the trigger.

Once the obstruction comes out of the spray tip,

release the trigger, reverse the spray tip back to

the spray pattern setting, and resume spraying.

Do not attempt to clean the tip with your finger.

Do not use a needle or other sharp pointed instrument to

clean the tip. The hard tungsten carbide is brittle and can

be chipped.

Maintenance

Before proceeding, follow the Pressure Relief Procedure

outlined previously in this manual. Additionally, follow all

other warnings to reduce the risk of an injection injury,

injury from moving parts, or electric shock.

General Repair and Service Notes

The following tools are needed when repairing this sprayer:

Phillips screwdriver 3/8" hex wrench

needle-nose pliers 5/16" hex wrench

adjustable wrench 1/4" hex wrench

rubber mallet 3/16" hex wrench

flat-blade screwdriver 1/8” hex wrench

1/2” open-end wrench 7/8” open-end wrench

1. Before repairing any part of the sprayer, read the

instructions carefully, including all warnings.

Never pull on a wire to disconnect it. Pulling on a wire

could loosen the connector from the wire.

2. Test your repair before regular operation of the sprayer to

be sure that the problem is corrected. If the sprayer does

not operate properly, review the repair procedure to

determine if everything was done correctly. Refer to the

Troubleshooting section to help identify other possible

problems.

3. Make certain that the service area is well ventilated in

case solvents are used during cleaning. Always wear

protective eyewear while servicing. Additional protective

equipment may be required depending on the type of

cleaning solvent. Always contact the supplier of solvents

for recommendations.

4. If you have any further questions concerning your

SprayTECH airless sprayer, call SprayTECH:

Technical Service...................................1-800-292-4637

Fax ................................................1-800-525-9501

CAUTION

NOTE: All Honda engine work should be performed by

a Honda authorized service center.

WARNING

CAUTION

Maintaining the Engine

When transporting a sprayer with a gas engine, make sure

the fuel is shut off.

Important Facts Concerning this Sprayer

This gas-powered sprayer contains a clutch that engages

when the sprayer is pumping. The sprayer’s pressure control

system engages and disengages the clutch to control

pressure. To prevent unnecessary wear to the clutch, it is

advisable to adjust the engine speed and pressure setting to

limit the amount of times the clutch engages and disengages.

To reduce clutch wear, refer to the following examples.

Example:

Operating one gun with a .019 tip — reduce the engine speed

by adjusting the throttle to a low or medium setting and

increase pressure only until the heavy ends of the spray

pattern have been eliminated.

Example:

Operating one gun with .023 tip — increase engine speed to a

high setting and increase pressure until the heavy ends of the

spray pattern have been eliminated.

Example:

Spraying light-bodied materials at low pressure — to reduce

surging at the gun and to decrease clutch wear, reduce the

engine speed to idle and reduce pressure until the desired

spray pattern is achieved.

Routine Engine Maintenance

Daily

• Check and fill the gas tank.

• After the first 20 hours of operation, drain the oil and refill

with clean oil. Check the engine oil level and fill as

necessary.

Weekly

• Remove the cover of the air filter and clean the element.

Replace the element if necessary. If operating in an

unusually dusty environment, check the filter daily and

replace if necessary. (Replacement elements can be

purchased from your local SprayTECH dealer.)

• After each 50 hours of operation: Change the engine oil.

Spark Plug

• Use only a (NKG) BP6ES plug.

• Gap the plug 0.025” – 0.030” (0.7 – 0.8 mm).

• Make sure to use a spark plug wrench when installing and

removing the plug.

NOTE: For detailed engine specifications and

maintenance, refer to the separate engine

manual supplied with this sprayer.

WARNING

Replacing the Filter

1. Loosen and remove the filter

body by hand.

2. Remove the filter and core

spring from the filter housing.

3. Remove the core spring from

inside the filter.

4. Inspect the filter. Based on

inspection, clean or replace the

filter.

5. Inspect the filter housing o-ring.

Based on inspection, clean or

replace the o-ring.

6. Slide the new or cleaned filter

over the core spring. Place the

filter and core spring into the

center of the filter housing.

7. Clean the inside of the filter

body.

8. Slide the filter body over the

filter and thread it into the filter

housing until secure.

Replacing the PRIME/SPRAY Valve

Perform the following procedure using PRIME/SPRAY valve

replacement kit P/N 0507690.

1. Drive the groove pin out of the valve handle.

2. Remove the valve handle and the cam base.

3. Using a wrench, loosen and remove the valve housing

assembly.

4. Make sure the gasket is in place and thread the new valve

housing assembly into the filter housing. Tighten securely

with a wrench.

5. Place the cam base over the valve housing assembly.

Lubricate the cam base with grease and line up the cam

with the filter block using the dowel pin.

6. Line up the hole on the valve stem with the hole in the

valve handle.

7. Insert the groove pin into the valve handle and through

the valve stem to secure the valve handle in position.

Dowel Pin

Cam Base

Valve Stem

Filter

Housing

Valve Housing

Assembly

Gasket

Valve Handle

Groove Pin

NOTE: The filter body should

be hand-tightened,

but make sure it is

seated fully into the

filter housing.

Filter

Body

Core

Spring

Filter

Housing

O-ring

Filter

Housing

Replacing the Potentiometer

Electrostatic discharge (ESD) potential could cause

damage to electronic pressure control. Use SprayTECH

ESD wrist strap P/N 0507958 or equivalent when working

on electronic pressure control.

1. Perform the Pressure Relief Procedure.

2. Pry off the pressure control knob cap to expose the knob

tension nut.

3. Turn the pressure control knob fully counterclockwise to

the minimum pressure setting.

4. Using a 5/16” socket, loosen the tension nut in the center

of the knob. Remove the knob.

5. Using a Phillips screwdriver, remove the four screws that

secure the electronic pressure control (EPC) assembly to

the EPC housing. Carefully remove the EPC assembly

from the housing. Gently move the assembly away from

the sprayer and allow the assembly to hang from the

housing.

6. Hold the potentiometer inside the EPC housing while

using a 1/2” thin wall socket to remove the seal nut that

secures the potentiometer to the mounting plate. Remove

the potentiometer from the EPC housing.

7. Carefully remove the potentiometer wires from their

connection point on the EPC board.

8. Insert the stem of the new potentiometer through the hole

in the mounting plate from inside the EPC housing.

Position the protruding tab on the potentiometer face into

the hole on the underside of the mounting plate (the wires

will face the open side of the EPC housing).

9. Thread the seal nut onto the threaded portion of the stem

and tighten using a 1/2” thin wall socket.

Do not over-tighten the seal nut.

10. Turn the potentiometer stem fully counterclockwise.

11. Place the pressure control knob on the potentiometer

stem with the indicator tab resting at the “minimum

pressure” tab on the mounting plate.

12. Tighten the knob tension nut using a 5/16” socket.

Do not over-tighten the knob tension nut. Over-tightening

will damage the potentiometer.

13. Connect the potentiometer wires to the EPC board. The

protruding tab on the EPC board connector will mate with

the slot on the potentiometer wires connector. The

connector on the end of the potentiometer wires and the

connector on the EPC board will mate only one way. Do

not force the connectors together.

14. Carefully place the EPC assembly over the EPC housing

taking care not to pinch any wires.

15. Install the four screws that secure the EPC assembly to

the EPC housing. Tighten securely.

CAUTION

EPC

Housing

Pressure Control Knob

Seal Nut

Cap

EPC

Board

EPC

Assembly

EPC

Assembly

Screw

Potentiometer

WARNING

Replacing the Pump ON/OFF Switch

Electrostatic discharge (ESD) potential could cause

damage to electronic pressure control. Use SprayTECH

ESD wrist strap P/N 0507958 or equivalent when working

on electronic pressure control.

1. Perform the Pressure Relief Procedure.

2. Using a Phillips screwdriver, remove the four screws that

secure the electronic pressure control (EPC) assembly to

the EPC housing. Carefully remove the EPC assembly

from the housing. Gently move the assembly away from

the sprayer and allow the assembly to hang from the

housing.

3. Locate the bottom of the pump ON/OFF switch inside the

EPC housing.

4. Disconnect the switch wires from the pump ON/OFF

switch. Remember the locations of each of the two wires

(label the wires, if necessary).

5. Depress the mounting tabs on each corner of the pump

ON/OFF switch inside the EPC housing and remove the

switch through the top of the housing.

6. Snap the new pump ON/OFF switch into the switch hole

in the EPC housing.

7. Connect the two switch wires to the new pump ON/OFF

switch. Make sure the wires are connected to the

corresponding terminals from which they were removed

(refer to the labels created earlier in this procedure or the

electrical schematic in the Parts List section of this

manual).

8. Carefully place the EPC assembly over the EPC housing

taking care not to pinch any wires.

9. Install the four screws that secure the EPC assembly to

the EPC housing. Tighten securely.

EPC

Housing

Pump ON/OFF

Switch

EPC

Board

EPC

Assembly

EPC

Assembly

Screw

WARNING

Replacing the Transducer

Electrostatic discharge (ESD) potential could cause

damage to electronic pressure control. Use SprayTECH

ESD wrist strap P/N 0507958 or equivalent when working

on electronic pressure control.

1. Perform the Pressure Relief Procedure.

2. Using a Phillips

screwdriver, remove

the four screws that

secure the electronic

pressure control

(EPC) assembly to the

EPC housing.

Carefully remove the

EPC assembly from

the housing. Gently

move the assembly

away from the sprayer

and allow the assembly to hang from the housing.

3. Locate the transducer wire in the EPC housing. This wire

will be protruding from a hole in the lower left hand corner

of the EPC housing. Disconnect this wire from the EPC

board (it has a phone jack-style connector).

4. Break off the locking tab from the phone jack-style

connector at the end of the transducer wire.

5. Using a 7/8” open-end wrench, loosen and remove the

fluid hose from the fitting on the bottom of the filter

assembly.

6. Using a 9/16” open-end wrench, loosen and remove the

return hose from the bottom of the filter assembly.

7. Using a 1/2” socket, remove the two hex screws that

secure the filter assembly to the cart.

8. Lift the filter assembly off the cart so that the transducer

tube moves out of the hole in the gear housing. Gently

pull the transducer wire through the housing until it is fully

disengaged from the hole.

9. Mount the filter assembly in a vise for easy access to the

transducer.

Do not over-tighten the vise.

10. Using a 3/4” open-end wrench, turn the transducer nut

counterclockwise to remove the transducer from the filter

housing.

11. Locate the new transducer. Make sure that there is a

white, PTFE o-ring on the end of the transducer that gets

inserted into the filter housing.

12. Insert the transducer into the filter housing port. Rotate

the transducer nut clockwise to tighten it into the filter

housing. Torque the nut to 360–400 in./lbs.

13. Remove the filter assembly from the vise.

Transducer

Filter Assembly

Hex Screw

Gear Housing

Filter

Assembly

Fluid

Hose

Fitting

Cart

CAUTION

EPC

Housing

EPC Assembly Screw

EPC Assembly

EPC

Board

WARNING

14. Insert the phone jack-style connector on the new

transducer wire into the hole in the gear housing from

which the old transducer wire was removed. Push the

wire and connector until the connector is visible in the

EPC housing.

15. Gently pull the wire into the EPC housing while moving

the filter assembly to its mounting point on the cart. Guide

the end of the transducer tube into the hole in the gear

housing.

16. Mount the filter assembly to the cart using the two hex

screws and lock washers. Torque the screws to 100–130

in./lbs.

17. Using a 7/8” open-end wrench, attach the fluid hose to the

fitting on the bottom of the filter assembly. Tighten

securely.

18. Using a 9/16” open-end wrench, attach the return hose to

the bottom of the filter assembly. Tighten securely.

19. Plug the phone jack-style connector on the transducer

wire into the socket on the EPC board from which the old

connector was removed.

20. Carefully place the EPC assembly over the EPC housing

taking care not to pinch any wires.

21. Install the four screws that secure the EPC assembly to

the EPC housing. Tighten securely.

22. Take the sprayer to a SprayTECH Authorized Service

Center for re-calibration.

23. After re-calibration, pressurize the system and check for

leaks.

Replacing the Electronic Pressure

Control (EPC) Assembly

Electrostatic discharge (ESD) potential could cause

damage to electronic pressure control. Use SprayTECH

ESD wrist strap P/N 0507958 or equivalent when working

on electronic pressure control.

1. Perform the Pressure Relief Procedure.

2. Using a Phillips

screwdriver, remove

the four screws that

secure the electronic

pressure control

(EPC) assembly to

the EPC housing.

Carefully remove the

EPC assembly from

the housing. Gently

move the assembly

away from the sprayer

and allow the assembly to hang from the housing.

3. Remember the locations of all the wire connections on the

EPC board (refer the electrical schematic located in the

Parts List section of this manual). If necessary, label all

the connections so that they can be replaced in their exact

location when the assembly is replaced.

4. Disconnect all the wires from the EPC board.

5. Connect all the wires to the new EPC assembly board

(refer to the labels created earlier in this procedure or the

electrical schematic in the Parts List section of this

manual).

6. Carefully place the EPC assembly over the EPC housing

taking care not to pinch any wires.

7. Install the four screws that secure the EPC assembly to

the EPC housing. Tighten securely.

8. Take the sprayer to a SprayTECH Authorized Service

Center for re-calibration.

EPC

Housing

EPC Assembly Screw

EPC Assembly

EPC

Board

WARNING

Replacing the Slider Assembly and

Slider Housing

1. Start the engine (refer to the procedures in the Operation

section of this manual). Turn the pressure control knob

clockwise to its maximum pressure setting.

2. Toggle the pump ON/OFF switch between the ON and

OFF positions in short bursts until the slider assembly

stops in a position where the fluid section connecting pin

and retaining ring are visible through the slot in the slider

housing.

3. Turn off the engine and perform the Pressure Relief

Procedure.

4. Using a Phillips

screwdriver,

remove the four

front cover

screws. Remove

the front cover.

5. Slide the retaining

ring up on the

slider assembly to

expose the

connecting pin.

6. Push the

connecting pin

forward through

the slider

assembly and

piston. The

connecting pin will

fall out from the rear window of the slider housing where it

can be retrieved.

7. Using a 7/8” open-end wrench, loosen and remove the

fluid hose from the fitting on the back of the fluid section.

8. Using a 21/4” wrench, loosen the fluid section jam nut.

Turn the fluid section counterclockwise by until it

disengages from the slider housing.

9. Using a 5/16” hex wrench, remove the four socket screws

and lock washers that secure the slider housing to the

pump housing.

10. Remove the slider housing and slider assembly by pulling it

straight out from the pump housing. The slider housing

assembly will disengage from the pump housing dowel pins

and the connecting rod will disengage from the crankshaft.

11. Remove the slider assembly from the slider housing by

grasping the bearing end of the connecting rod and lifting

it straight out from the slider housing.

12. Check the parts for wear.

a. If the slider housing bushing is scored or out of round it

should be replaced.

b. If the slider assembly is scored or the connection

between the connecting rod and slider assembly

exhibits movement other than pivoting movement, the

slider assembly should be replaced. The slider

assembly also should be replaced if the connecting rod

bearing shows signs of wear.

c. Any parts that will be reused should be cleaned

thoroughly, including the connecting rod. Also, clean the

crankshaft pin that the connecting rod bearing rides on.

d. If a new slider assembly will be used, remove the

retaining ring from the bottom of the old slider assembly

and slide it onto the new assembly so that it rests

above the connecting pin hole.

13. Lubricate the inside diameter of the slider housing and the

outside diameter of the slider assembly with oil. Fill the

slider cup with Lubriplate 3000W grease (the slider cup is

the area on the slider assembly where the connecting rod

and slider housing join and pivot).

14. Insert the slider assembly into the bushing end of the

slider housing.

Connecting

Fitting

Retaining

Ring

Slider

Assembly

Pump

Housing

Front

Cover

Screw

Slider

Housing

Jam Nut

Fluid

Section

Front

Cover

15. Hold the assembly up to the pump housing, lining up the

connecting rod with the crankshaft pin and the pump

housing dowel pins with their mating holes on the slider

housing. Slide the assembly onto the crankshaft pin and

pump housing dowel pins until the slider housing bottoms

out on the pump housing. Make sure the grease fitting on

the connecting rod is facing the open side of the pump

housing.

16. Install the the four socket screws and lock washers that

secure the slider housing to the pump housing. Tighten in

a diagonal pattern and torque to 400–440 in./lbs.

17. Lubricate the connecting rod bearing with Lubriplate 1242

grease by inserting the end of a grease gun onto the

grease fitting on the end of the crankshaft pin. Lubricate

the main housing bearing by inserting the end of a grease

gun onto the grease fitting in the center of the crankshaft.

Also, lubricate the connecting rod bushing by inserting the

end of a grease gun onto the grease fitting on the

connecting rod.

18. Position the front cover over the pump housing. Secure

the front cover using the four front cover screws.

19. Apply blue Loctite to the bottom 3–4 threads on the fluid

section cylinder.

20. Turn the fluid section jam nut clockwise until it is flush

against the top of the cylinder.

21. Lubricate the first several threads at the top of the cylinder

with anti-seize compound.

22. Thread the cylinder into the pump housing, turning

clockwise. When the connecting pin hole on the piston

rod lines up with the hole in the slider assembly, insert the

connecting pin.

23. Slide the retaining ring down on the slider assembly to

cover the connecting pin.

24. Continue to turn the cylinder clockwise until the jam nut is

flush against the slider housing.

25. Once the nipple is positioned, turn the jam nut clockwise

until it contacts the pump housing.

26. Tighten the jam nut with a wrench to tighten it against the

slider housing.

27. Using a 7/8” open-end wrench, attach the fluid hose to the

fitting on the back of the fluid section. Tighten securely.

NOTE: If the nipple on the cylinder does not face the

back of the unit, turn the cylinder

counterclockwise until the nipple faces the

back of the unit. Do not turn the cylinder more

than one full turn.

Crankshaft

Dowel Pin

Connecting Rod

Slider Housing

Socket Screw

Pump

Housing

Slider Housing

Slider Assembly

Replacing the Gears

1. Perform the Pressure Relief Procedure.

2. Using a Phillips screwdriver, remove the four front cover

screws. Remove the front cover..

3. Using a 7/8” open-end wrench, loosen and remove the

fluid hose from the fitting on the back of the fluid section.

4. Locate the four socket screws that secure the pump

housing to the gear housing. Two are at the inside top of

the pump housing and two are located on the external

bosses at the bottom of the pump housing.

5. Using a 1/4” hex wrench, remove the four socket screws

that secure the pump housing to the gear housing.

6. Slide the pump housing assembly away from the gear

housing.

7. Remove and clean the housing gasket. Replace if

damaged.

8. Remove the gear assembly and the 1/4” thrust balls from

within the bearing bores that support the gear.

9. Inspect the gears for excessive wear and replace if

damaged or worn. If the gear assembly is replaced,

replace the two thrust balls as well.

10. Inspect the pinion gear on the end of the drive shaft for

wear. Replace if damaged or worn (refer to the “Servicing

the Clutch Assembly” procedure in this section).

11. Inspect the output gear and the two thrust washers on the

end of the crankshaft in the pump housing for wear. This

gear is permanently attached to the crankshaft and pump

housing. If this gear is worn, the pump housing must be

replaced.

12. Replace the thrust washers if worn. If the pump housing

assembly is replaced, replace the thrust washers as well.

13. Coat each of the thrust balls with a generous amount of

grease. Install the thrust balls — one in the gear housing

bore and one in the pump housing bore.

14. Coat the gear assembly with fresh Lubriplate GR-132

grease. Insert the gear assembly into the bore in the

pump housing, pinion end first.

15. Generously coat both faces of each of the crankshaft

thrust washers with grease.

NOTE: If any of the gears are worn and require

replacement, check the grease in the gear

housing for metal particles or shavings.

Remove the contaminated grease. Replace the

grease that has been removed with fresh

Lubriplate GR-132 grease.

NOTE: If replacing the pump housing , first remove

the fluid section, slider housing, and slider

assembly from the pump housing (refer to the

“Replacing the Slider and Slider Housing”

procedure in this section).

Housing Gasket

Gear Housing

Thrust Ball

Thin Thrust Washer

Thrust Ball

Front

Cover

Pump Housing

Gear

Assembly

Thick Thrust

Washer

Pump Housing

Socket Screw

Front Cover

Screw

16. Place the thick thrust washer onto the crankshaft up

against the gear hub. Next, place the thin thrust washer

up against the thick washer on the crankshaft.

17. Place the housing gasket over the gear housing dowel pins.

18. Carefully place the pump housing assembly in front of the

gear housing assembly, lining up the gear housing dowel

pins with their corresponding holes in the pump housing.

Slide the pump housing onto the gear housing until there

is no gap between the housings and gasket.

Do not force the pump housing and gear housing together.

19. Locate the four socket screws and lock washers that secure

the pump housing to the gear housing. The longer screws

(2.25”) are fastened into the top internal holes. The shorter

screws (2”) are fastened into the bottom external bosses.

20. Using a 1/4” hex wrench, snug and tighten the socket

screws in a crossing pattern. Torque to 200–230 in./lbs.

21. If the slider, slider housing, and fluid section were

removed, reinstall by following the steps in the “Replacing

the Slider and Slider Housing” procedure in this section.

22. Position the front cover over the pump housing. Secure

the front cover using the four front cover screws.

23. Using a 7/8” open-end wrench, attach the fluid hose to the

fitting on the back of the fluid section. Tighten securely.

Servicing the Clutch Assembly

Removing/Replacing the Clutch Hub and

Armature Assembly

1. Perform the Pressure Relief Procedure.

2. Using a 7/8” open-end wrench, loosen and remove the

fluid hose from the fitting on the back of the fluid section.

3. Hold the transducer tube with a pliers to prevent it from

rotating and turn the transducer nut counterclockwise

using a 3/4” open-end wrench. When the nut disengages

the filter housing, carefully remove the transducer from the

filter housing.

4. Locate the wire that exits the rear of the electronic

pressure control (EPC) housing and connects to the wire

harness on the engine. Disconnect this wire from its

connector at the engine wire harness.

5. Using a 1/2” wrench, remove the four hex screws and lock

washers that secure the clutch housing to the gear housing.

6. Using a 9/16” socket, remove the two hex screws that

secure the gear housing to the cart.

7. Slide the pump and gear housings away from the engine

to disengage them from the clutch housing.

Clutch Armature

Clutch Hub

Taper Lock Bushing

Gear

Housing

Pump

Housing

Lock

Washer

Clutch

Housing

Clutch Housing

Hex Screw

Engine Shaft

Gear Housing

Hex Screw

Set Screw

NOTE: When replacing the clutch armature, the clutch

hub and clutch rotor must be replaced also.

This will allow for even wear and maximum life

on clutch parts.

CAUTION

8. Locate the clutch hub and armature assembly on the end

of the engine shaft. Note the two set screws as well as

the unused, threaded hole in the taper lock bushing at the

center of the clutch hub.

9. Using an 1/8” hex wrench, remove the two set screws

from the taper lock bushing

10. Thread one of the set screws into the unused, threaded hole

on the taper lock bushing. As the screw tightens, the bushing

will loosen. Once the bushing has loosened enough, slide the

clutch hub and armature assembly off the engine shaft.

11. Before replacing the clutch

hub and armature assembly

the proper “set back” must

be created. Using the

SprayTECH hub set-up tool

(P/N 0509925), create a “set

back” of 0.20” between the

friction surface of the clutch

armature and the forward face of the clutch hub.

12. Line up the three holes in the taper lock bushing with the

three holes in the clutch hub and insert the bushing into

the center of the clutch hub.

13. Line up the key on the taper lock bushing with the keyway

on the engine shaft and slide the assembly onto the shaft

with the holes facing out.

14. Apply blue Loctite to the

two set screws and insert

the screws into the taper

lock bushing. Tighten the

set screws only two turns

at this time.

15. Line up the forward face

of the clutch hub with the

front face of the clutch

housing. Using an 1/8”

hex wrench, alternately

tighten the set screws

into the taper lock bushing. Torque to 65–75 in/lbs.

16. Make sure the friction surface of the clutch armature is

clean and free from oil or grease.

Removing the Clutch Rotor, Clutch Field, and

Drive Shaft Assembly

1. Follow steps 1–7 in “Removing/Replacing the Clutch Hub

and Armature Assembly.”

2. Locate the clutch rotor assembly on the end of the drive shaft

assembly. Note the locations of the three socket screws and

the two empty, threaded holes on the clutch rotor.

3. Using a 3/16” hex wrench, remove the three socket

screws and lock washers that secure the clutch rotor to

the drive shaft assembly.

4. Thread two of the socket screws into the empty, threaded

holes and tighten alternately. This will push the clutch

rotor away from the drive shaft assembly and pinion.

Electrostatic discharge (ESD) potential could cause

damage to electronic pressure control. Use SprayTECH

ESD wrist strap P/N 0507958 or equivalent when working

on electronic pressure control.

WARNING

NOTE: To ensure the clutch hub and the clutch

housing are aligned, hold a straight edge

across the face of the clutch housing and then

hold the clutch hub against the back of the

straight edge while tightening the two set

screws into the taper lock bushing.

Clutch

Housing

0.20"

Engine

Set

Screw

Straight

Edge

Tape r

Lock

Bushing

NOTE: A new clutch hub and

armature assembly will

come pre-assembled, but

the “set back” will not be

correct. The “set back”

must still be created using

the hub set-up tool.

0.20"

Clutch

Hub

Flat

Surface

Set-Up

Tool

Clutch

Armature

5. Using a Phillips screwdriver, remove the four screws that

secure the EPC assembly to the EPC housing. Carefully

remove the EPC assembly from the housing.

6. Locate the two clutch field wires that pass from the gear

housing into the EPC housing through a grommet in the

back of the EPC housing. Remember the wire connection

terminals on the EPC assembly (label if necessary) and

disconnect the wires. Gently move the EPC assembly

away from the housing and rest it on the work surface by

the control housing.

7. Locate the four set screws that secure the clutch field to

the gear housing. They are located on the exterior of the

gear housing at the 12, 3, 6, and 9 o’clock positions while

facing the clutch field end of the gear housing. Using an

1/8” hex wrench, remove the setscrews. Remember the

location of the two clutch field wires with respect to the

grommet and EPC housing.

8. Carefully slide the clutch field out of the gear housing,

keeping the field square to the gear housing so it does not

bind.

9. Remove the retaining ring in front of the ball bearing

within the center bore of the gear housing.

10. Follow steps 2–6 in the “Replacing the Gears” procedure

to remove the pump housing from the gear housing.

11. From the gear side of the gear housing, use a soft

hammer to tap the gear end of the drive shaft through the

gear housing.

12. Carefully slide the drive shaft assembly out from the gear

housing, keeping the shaft square to the housing so it

does not bind.

13. Remove the o-ring from inside the center bore of the gear

housing from which the small ball bearing on the drive

shaft assembly was removed.

14. Clean the inside of the gear housing.

Installing the Clutch Rotor Assembly, Clutch

Field and Drive Shaft Assembly

1. Install a new o-ring into the center bore of the gear housing.

2. Apply Loctite retaining compound #635 to the outside

diameter of the large bearing on the drive shaft. Do not get

retaining compound on the faces of the bearing.

3. Install the drive shaft assembly into the center bore of the

gear housing, keeping it square to the housing so it does

not bind. Once the large ball bearing on the drive shaft

assembly is half way into its bore, a soft hammer may be

used to gently tap the assembly into position.

Do not force the drive shaft assembly into position.

4. Install the retaining ring into its groove next to the large

ball bearing.

CAUTION

Clutch Rotor

Socket Screw

Retaining Ring

Clutch Field Wires

Drive Shaft

Assembly

Clutch

Field

Clutch Field

Set Screw

EPC

Housing

Lock

Washer

Clutch

Rotor

5. Line up the four holes around the outside of the clutch

field with the four set screw holes in the gear housing.

The clutch field wires should be at approximately the 1 or

2 o’clock position.

6. Route the two clutch field wires through the grommet and

into the EPC housing.

7. Carefully slide the clutch field into its bore in the gear

housing until it “bottoms out” within the housing. Do not

pinch the clutch field wires during installation.

8. Thread one of the set screws into its hole. Using an 1/8”

hex wrench, rotate the screw slowly until it contacts the

clutch field. Do not tighten the set screw. The tip of the

set screw should mate with the drill point hole in the field.

Check the clutch field for rotation. If it rotates within its

bore, the set screw is not seated within the drill point.

9. When the set screw is properly seated, install the remaining

three set screws. Do not tighten the set screws.

10. Using a crossing pattern, tighten each of the setscrews

until they are snug. Once all four set screws are snug,

use a crossing pattern to tighten and torque the set

screws to 60–70 in./lbs.

It is very important to evenly snug, tighten, and torque the

clutch field set screws in a crossing pattern. This ensures

the clutch field will stay centered in the gear housing.

11. Line up the three screw holes and dowel pin hole on the

clutch rotor with the screw holes and dowel pin on the drive

shaft assembly hub. Place the clutch rotor onto the hub.

12. Using a 3/16” hex wrench, thread the three socket screws

and lock washers through the clutch rotor and into the

drive shaft assembly hub. Evenly snug, tighten, and

torque the socket screws to 75–85 in/lbs.

13. Make sure the friction surface of the clutch rotor is clean

and free from oil or grease.

14. Follow steps 17–20 in the “Replacing the Gears” procedure

to mate the pump housing with the gear housing.

Electrostatic discharge (ESD) potential could cause

damage to electronic pressure control. Use SprayTECH

ESD wrist strap P/N 0507958 or equivalent when working

on electronic pressure control.

15. Locate the two clutch field wires in the EPC housing.

Gently pull the wires fully into the EPC housing so that

there is no slack in the gear housing. Connect the wires

to their proper terminals on the EPC board (refer to the

labels created earlier in this procedure or the electrical

schematic in the Parts List section of this manual).

16. Carefully place the EPC assembly over the EPC housing

taking care not to pinch any wires.

17. Install the four screws that secure the EPC assembly to

the EPC housing. Tighten securely.

Mating the Gear Housing and the Clutch Housing

1. Place the gear housing assembly onto the cart in front of

the clutch housing. Line up the dowel pins in the gear

housing with their corresponding holes in the clutch

housing. Slide the gear housing assembly onto the clutch

housing until there is no gap between the housings.

2. Thread the four hex screws and lock washers through the

clutch housing and into the gear housing.

3. Using a 1/2” wrench, snug and tighten the hex screws in a

crossing pattern. Torque to 140–155 in./lbs.

4. Using a 9/16” socket, thread the two hex screws that secure

the gear housing to the cart through the underside of the

cart and into the gear housing. Torque to 100–120 in./lbs.

5. Connect the wire from the EPC housing to its mating

connector on the engine wire harness.

WARNING

CAUTION

NOTE: Apply blue Loctite to the four clutch field set

screws prior to installation.

6. Make sure that there is a white PTFE o-ring on the end of

the transducer that gets inserted into the filter housing.

Insert the transducer into the filter housing port.

7. Hold the transducer tube with a pliers to prevent it from

rotating, and turn the transducer nut clockwise with a 3/4”

open-end wrench to tighten it into the filter housing.

Torque the nut to 360–400 in./lbs.

Checking the Clutch Gap

1. Remove the plastic plug from the top of the clutch

housing. Look through the port to locate the clutch

armature and the clutch rotor.

2. Check the gap between the clutch armature and the clutch

rotor using a .016” feeler gauge and a .035” feeler gauge.

a. Insert each feeler gauge through the port and into the

gap between the clutch armature and the clutch rotor.

The .016” feeler gauge should fit in the gap. The .035”

feeler gauge should not fit in the gap.

b. Pull the engine pull cord several times to rotate the

clutch armature, checking the gap with each feeler

gauge between each pull.

c. If the .016” gauge does not fit or the .035” gauge does

fit at any checkpoint, the gap must be readjusted. This

is done by relocating the clutch hub and armature

assembly on the engine shaft. Refer to the

“Removing/Replacing the Clutch Hub and Armature

Assembly” procedure.

Servicing the Fluid Section

Use the following procedures to service the valves and repack

the fluid section.

1. Start the engine (refer to the procedures in the Operation

section of this manual). Turn the pressure control knob

clockwise to its maximum pressure setting.

2. Toggle the pump ON/OFF switch between the ON and OFF

positions in short bursts until the slider assembly stops in a

position where the fluid section connecting pin and retaining

ring are visible through the slot in the slider housing.

3. Turn off the engine and perform the Pressure Relief

Procedure.

Before proceeding, follow the Pressure Relief Procedure

outlined previously in this manual. Additionally, follow all

other warnings to reduce the risk of an injection injury,

injury from moving parts or electric shock.

4. Remove the return hose from

the clamp on the siphon tube.

Unscrew the siphon tube from

the inlet valve housing.

5. Loosen and remove the fluid

hose from the fitting on the back

of the cylinder of the fluid

section.

6. Loosen and remove the four

front cover screws. Remove

the front cover.

7. Slide the retaining ring up on

the slider assembly to expose

the connecting pin.

8. Push the connecting pin forward

through the slider assembly and

piston. The connecting pin will

fall out from the rear window of the slider housing where it

can be retrieved.

Connecting

Fitting

Retaining

Ring

Slider

Assembly

Jam Nut

Cylinder

WARNING

9. Using a wrench, turn the jam

nut counterclockwise to loosen

it from the pump housing.

10. Turn the fluid section

counterclockwise to remove it

from the pump housing.

11.Place the fluid section cylinder

upright in a vise by clamping

on the wrench flats.

12. Loosen and remove the inlet

valve housing from the

cylinder.

13. Remove the inlet cage, inlet

valve ball, inlet valve seat, and

o-ring from the inlet valve.

14. Clean out any debris in the inlet valve housing and

examine the housing and the inlet valve seat. If the seat

is damaged, reverse to the unused side or replace the

seat.

15. Using a wrench, remove the upper seal retainer.

16. Slide the piston rod out through the bottom of the cylinder.

17. Inspect the piston rod for wear

and replace if necessary.

18. Remove the adapter ring and

upper packing assembly from

the top of the cylinder.

19. Remove the seal washer, lower

support ring and lower packing

assembly from the bottom of

the cylinder.

20. Remove the cylinder from the

vise.

21. Insert the connection pin

through the hole at the top of

the piston rod and clamp each

end of the connecting pin in the

vise. This will hold the piston

rod in position for disassembly.

22. Using a 3/8” hex wrench, loosen

and remove the outlet valve

retainer from the piston rod.

23. Remove the outlet valve seal,

outlet cage, outlet valve ball,

nylon washer, and outlet valve

seat from the outlet valve

retainer.

24. Clean out any debris and

examine the retainer and outlet

valve seat. If the seat is

damaged, reverse to the unused

side or replace the seat.

25. Clean and inspect the outlet cage and outlet valve ball.

Replace if they are worn or damaged.

NOTE: Do not clamp the

piston rod directly in

the vise. Damage to

the piston rod will

occur.

NOTE: Be careful not to

scratch, score, or

otherwise damage the

cylinder during

removal of the packing

assemblies.

Piston Rod

Cylinder

Upper

Seal

Retainer

Adapter

Ring

Seal

Washer

Upper

Packing

Assembly

Lower

Packing

Assembly

Outlet Valve

Seat

Nylon Washer

Outlet Cage

Outlet Valve

Ball

Outlet Valve

Seal

Outlet Valve

Retainer

Lower

Support

Ring

NOTE: Do not over-tighten

the vise. Damage to

the cylinder may

occur.

Inlet Valve

Housing

Viton

O-Ring

O-ring

PTFE

Back-Up

Ring

Inlet Valve

Seat

Inlet Valve

Ball

Inlet Cage

Cylinder

26. Reassemble the outlet valve assembly into the piston rod

in the reverse order of how it was disassembled. Use the

new parts supplied with the packing kit during reassembly.

Apply blue Loctite #242 to the threads of the outlet valve

retainer. Torque the outlet valve retainer to 144 in./lbs.

27. Remove the piston rod from the vise.

28. Clean the cylinder. Inspect the cylinder for damage and

replace if necessary.

29. Place the cylinder upright in a vise by clamping on the

wrench flats.

30. Locate the new upper and lower packing assemblies and

pack the areas between the packing lips with grease.

Lubricate the o-rings on the exterior of the packings with

grease.

31. Insert the upper packing

assembly into the top of the

cylinder with the large beveled

edge facing down.

32. Insert the new adapter ring into

the top of the cylinder with the

small, center protrusion facing

down. The adapter ring should

rest on the upper packing

assembly.

33. Apply blue Loctite #242 to the threads of the upper seal

retainer. Thread the upper seal retainer into the cylinder

but do not tighten.

34. Rotate the cylinder in the vise so that the bottom end is

facing up.

35. Pre-form the lower packing using the lower packing sizing

tool (included in the repacking kit).

36. Insert the lower packing

assembly partially into the

bottom of the cylinder with the

large beveled edge facing

toward the cylinder (beveled

edge will be facing up when the

cylinder is upright).

37. Push the lower packing

assembly into position using the

lower packing insertion tool (see Fluid Section Assembly

parts list for lower packing insertion tool P/N).

38. Place the piston insertion tool (included in the repacking

kit) over the top of the piston rod.

39. Insert the piston rod into the bottom of the cylinder,

through the lower packing assembly, through the upper

packing assembly, and out through the upper seal

retainer.

40. Tighten the upper seal retainer. Torque to 450–480 in./lbs.

41. Apply blue Loctite to the bottom 3–4 threads on the

cylinder. Turn the jam nut clockwise until it is flush against

the top of the cylinder.

42. Lubricate the first several threads at the top of the cylinder

with anti-seize compound. Remove the cylinder from vise.

43. Thread the cylinder into the pump housing, turning

clockwise. When the connecting pin hole on the piston

rod lines up with the hole in the slider assembly, insert the

connecting pin.

44. Slide the retaining ring down on the slider assembly to

cover the connecting pin.

NOTE: When repacking the fluid section, make sure the

raised lip on the bottom of the lower packing

assembly is fully outside the packing around the

piston rod after insertion of the piston rod.

Install lower packing so

large beveled edge will

be facing up when the

cylinder is upright.

Large Beveled Edge

Install upper packing

with large beveled

edge facing down.

Large Beveled Edge

45. Continue to turn the cylinder clockwise until the jam nut is

flush against the pump housing.

46. Once the nipple is positioned, turn the jam nut clockwise

until it contacts the pump housing.

47. Tighten the jam nut with a wrench to tighten it against the

pump housing. Torque to 680–720 in./lbs.

48. Attach the high-pressure hose to the fitting on the back of

the cylinder and tighten with a wrench. Do not kink the

hose.

49. Insert the lower support ring and new seal washer into the

bottom of the cylinder.

50. Making sure that the new Viton o-ring and new PTFE

back-up ring are lubricated and in place, reassemble the

inlet valve assembly and thread it into the cylinder. Use

the new parts supplied with the packing kit during

reassembly. Tighten the inlet valve housing until the o-

ring engages, then continue to tighten until snug.

51. Using a wrench, hold the cylinder by the wrench flats and

torque the inlet valve housing to 1020–1080 in./lbs.

52. Thread the siphon tube into the inlet valve housing and

tighten securely. Make sure to wrap the threads on the

siphon tube with PTFE tape before assembly. Replace the

return hose into the clamp on the siphon tube.

53. Place the front cover on the pump housing and secure in

position using the four front cover screws.

54. Turn on the sprayer by following the procedure in the

“Operation” section of this manual and check for leaks.

NOTE: Repacking kit P/N 0509940 is available. For

best results use all parts supplied in this kit.

NOTE: If the nipple on the cylinder does not face the

back of the unit, turn the cylinder

counterclockwise until the nipple faces the

back of the unit. Do not turn the cylinder more

than one full turn.

Troubleshooting

Problem

The unit will not run.

The unit will not prime.

The unit will not build or

maintain pressure.

Fluid leakage at the upper end

of the fluid section.

Excessive surge at the spray

gun.

Poor spray pattern.

The unit lacks power.

Cause

1. The pressure is set too low.

2. Faulty or loose wiring.

3. The gas tank is empty.

1. The PRIME/SPRAY valve is in the

SPRAY position.

2. Air leak in the siphon tube/suction set.

3. The pump filter and/or inlet screen is

clogged.

4. The siphon tube/suction set is clogged.

1. The spray tip is worn.

2. The spray tip is too large.

3. The pressure control knob is not set

properly.

4. The pump filter, gun filter, or inlet

screen is clogged.

5. Material flows from the return hose

when the PRIME/SPRAY valve is in the

SPRAY position.

6. Air leak in the siphon tube/suction set.

7. There is external fluid leak.

8. There is an internal fluid section leak

(packings are worn and/or dirty, valve

balls are worn).

9. Worn valve seats

1. The upper packings are worn.

2. The piston rod is worn.

1. Wrong type of airless spray hose.

2. The spray tip worn or too large.

3. Excessive pressure.

1. The spray tip is too large for the

material being used.

2. Incorrect pressure setting.

3. Insufficient fluid delivery.

4. The material being sprayed is too

viscous.

1. The pressure adjustment is too low.

Solution

1. Turn the pressure control knob clockwise to

supply power to the unit and increase the

pressure setting.

2. Inspect or take to a SprayTECH authorized

service center.

3. Fill the gas tank.

1. Rotate the PRIME/SPRAY valve clockwise

to the PRIME position.

2. Check the siphon tube/suction set

connection and tighten or re-tape the

connection with PTFE tape.

3. Remove the pump filter element and clean.

Remove the inlet screen and clean.

4. Remove the siphon tube/suction set and

clean.

1. Replace the spray tip following the

instructions that came with the spray gun.

2. Replace the spray tip with a tip that has a

smaller orifice following the instructions that

came with the spray gun.

3. Turn the pressure control knob clockwise to

increase the pressure setting.

4. Remove the pump filter element and clean.

Remove the gun filter and clean. Remove

the inlet screen and clean.

5. Clean or replace the PRIME/SPRAY valve.

6. Check the siphon tube/suction set

connection and tighten or re-tape the

connection with PTFE tape.

7. Check for external leaks at all connections.

Tighten connections, if necessary.

8. Clean the valves and service the fluid

section following the “Servicing the Fluid

Section” procedure in the Maintenance

section of this manual.

9. Reverse or replace the valve seats following

the “Servicing the Fluid Section” procedure

in the Maintenance section of this manual.

1. Repack the pump following the “Servicing

the Fluid Section” procedure in the

Maintenance section of this manual.

2. Replace the piston rod following the

“Servicing the Fluid Section” procedure in

the Maintenance section of this manual.

1. Replace hose with a minimum of 50’ of 1/4”

grounded textile braid airless paint spray

hose.

2. Replace the spray tip following the

instructions that came with the spray gun.

3. Rotate the pressure control knob

counterclockwise to decrease spray

pressure.

1. Replace the spray tip with a new or smaller

spray tip following the instructions that

came with the spray gun.

2. Rotate the pressure control knob to adjust

the pressure for a proper spray pattern.

3. Clean all screens and filters.

4. Add solvent to the material according to the

manufacturer's recommendations.

1. Rotate the pressure control knob clockwise

to increase the pressure setting.

Consignes de sécurité

Le présent manuel comprend des renseignements devant être

lus attentivement avant toute utilisation de l'appareil. Lorsque

l'un des symboles suivants apparaît, il est recommandé d'être

particulièrement attentif et de tenir compte des mesures de

sécurité indiquées.

Ce symbole indique un danger potentiel pouvant causer des

blessures graves ou même mortelles. Des renseignements

importants sur la sécurité sont également indiqués.

Ce symbole indique un danger potentiel pouvant causer des

blessures corporelles ou des dommages à l'équipement. Des

renseignements importants sur la façon de prévenir tout

dommage à l'équipement ou toute blessure corporelle mineure

sont également indiqués.

DANGER: BLESSURES PAR PERFORATION - Le jet de

peinture à haute pression produit par cet

appareil peut perforer la peau et les tissus

sous-jacents et entraîner de sévères blessures

pouvant nécessiter une amputation. Consultez

immédiatement un médecin.

NE PAS TRAITER UNE BLESSURE PAR PERFORATION

COMME UNE SIMPLE COUPURE! Une perforation peut

entraîner des risques d'amputation. Consultez

immédiatement un médecin.

Pression de service maximale du fluide dans l’appareil :

3300 lb/po2 / 22.8 MPa.

MESURES PRÉVENTIVES:

• NE JAMAIS diriger le pistolet vers une quelconque partie

du corps.

•NE JAMAIS mettre une quelconque partie du corps en

contact avec le jet de liquide. NE JAMAIS se mettre au

contact d'un jet de liquide provenant d'une fuite du flexible

d'alimentation en liquide.

• NE JAMAIS placer votre main devant le pistolet. Des

gants ne vous protégeront pas contre les risques de

blessures par perforation.

•TOUJOURS verrouiller la gâchette du pistolet, fermer la

pompe à liquide et décompresser l'appareil lorsque vous

travaillez sur celui-ci, nettoyez le protecteur de tête,

remplacez la tête de pulvérisation ou vous éloignez de

l'appareil. Couper le moteur ne décompresse pas l'appareil.

Vous devez, pour le décompresser, placer le bouton

AMORÇAGE/PULVÉRISATION en position AMORÇAGE.

Reportez-vous, pour cela, à la PROCÉDURE DE

DÉCOMPRESSION décrite dans de ce manuel.

•TOUJOURS s'assurer que le protecteur de tête est en

place lorsque vous pulvérisez. Le protecteur de tête offre

une certaine protection contre les blessures par perforation

mais sa principale fonction est d'ordre préventif.

•TOUJOURS ôter la tête de pulvérisation avant de purger

ou nettoyer l'appareil.

• Le flexible d'alimentation en peinture peut fuir à la suite

d'une usure, de chocs ou de mauvais traitements. Une

fuite peut entraîner une perforation de la peau. Inspecter

le flexible avant chaque utilisation.

• NE JAMAIS utiliser un pistolet dont la gâchette n'est pas

munie d'un loquet ou un cran de sécurité qui soit en état

de fonctionner.

•Tous les accessoires doivent être homologués pour une

pression égale ou supérieure à 3 200 lb/po2 / 22.8 MPa.

Cela s'applique, entre autres, aux têtes de pulvérisation,

aux accessoires du pistolet et aux flexibles.

AVERTISSEMENT

NOTA : Les remarques donnent des renseignements

importants requérant une attention particulière.

ATTENTION

AVERTISSEMENT

DANGER: RISQUES D'EXPLOSION OU D'INCENDIE - Les

vapeurs dégagées par le solvant ou la peinture

sont explosives et inflammables et peuvent

causer des corporels sérieux ou dommages

matériels.

MESURES PRÉVENTIVES:

•Veiller à éviter toute accumulation de vapeurs

inflammables en vous assurant que la zone où la

pulvérisation a lieu est suffisamment ventilée.

•Veiller à éviter la présence de toute source incandescente

telle qu'étincelle électrostatique, flamme nue, flamme-

pilote, objet brûlant, cigarette et étincelle provenant du

branchement ou du débranchement d'un cordon

d'alimentation électrique ou d'un commutateur.

• Ne pas fumer dans la zone d’épandage.

•Toujours avoir un extincteur en état de fonctionner à

portée de la main.

• Placer la pompe à peinture à une distance d’au moins un

mètre (3 pi) (on recommande d’ailleurs une plus grande

distance) de l’objet qui doit être vaporisé dans une pièce

séparée bien aérée, ou à une distance d’au moins six

mètres (20 pi) de celui-ci dans une zone bien aérée

(utiliser d’autres tuyaux si nécessaires). Les vapeurs

inflammables sont souvent plus lourdes que l’air. Le

plancher doit être extrêmement bien aéré. La pompe à

peinture contient des pièces pouvant créer des étincelles

et enflammer les vapeurs présentes dans l’air.

• Le matériel utilisé, ainsi que les objets se trouvant à

proximité de la zone de pulvérisation, doivent être

convenablement reliés à la terre afin d'éviter toute

étincelle ou toute décharge électrostatique.

• N'utiliser que des flexibles d'alimentation en liquide à

haute pression conducteurs ou reliés à la terre dans les

cas d'utilisation sans air comprimé. S'assurer que le

pistolet est convenablement relié à la terre par

l'intermédiaire du flexible.

• Le cordon d’alimentation doit être raccordé à un circuit

mis à la terre.

•Toujours purger l’appareil dans un contenant métallique

séparé, en s’assurant que la pompe soit à basse pression

et que le chapeau soit retiré. Tenir le pistolet fermement

contre la paroi du contenant pour mettre celui-ci à la terre

et empêcher l’émission d’étincelles causées par

l’électricité statique.

• Se conformer aux consignes et recommandations de

sécurité du fabricant du solvant ou du produit.

• S’entourer de toutes les précautions possibles lorsqu’on

utilise des produits ayant un point d’éclair inférieur à 21

°C (70 °F). Le point d’éclair d’un fluide est la température

à laquelle les vapeurs émanant du fluide peuvent

s’enflammer au contact d’une flamme ou d’une étincelle.

• Le plastique peut être une source d’étincelles provoquées

par l’électricité statique. Ne jamais utiliser une couverture

en plastique pour fermer une zone d’épandage ni utiliser

des toiles de protection en plastique lors de la

pulvérisation de matières inflammables.

• Lorsque vous purgez l'appareil, veillez à utiliser à la

pression minimale.

AVERTISSEMENT AUX MÉDECINS : Une perforation

sous-cutanée constitue un traumatisme. Il est

important de traiter la blessure de façon chirurgicale

aussitôt que possible. NE RETARDEZ PAS ce traitement

pour des recherches de toxicité. La toxicité n'est un

risque que dans les cas où certains produits de

revêtement pénètrent dans le flux sanguin. Il peut être

nécessaire de faire appel à des soins de chirurgie

plastique ou de reconstruction de la main.

Français

MOTEUR À ESSENCE

(DANS LES CAS OÙ CELA S’APPLIQUE)

Toujours placer la pompe à l’extérieur de la structure à l’air

frais. Garder tous les solvants loin de l’échappement du

moteur. Ne jamais remplir le réservoir à carburant lorsque le

moteur est en marche ou lorsqu’il est chaud ; les surfaces

chaudes risquent d’enflammer le carburant déversé

accidentellement. Toujours raccorder un fil de mise à la terre

entre la pompe et un objet mis à la terre, tel qu’une conduite

d’eau métallique. Se reporter au guide d’utilisation du moteur

pour obtenir de plus amples renseignements concernant la

sécurité.

DANGER: RISQUES D'EXPLOSION PAR INCOMPATIBILITÉ

DES MATÉRIAUX - Peuvent être à l'origine de

corporels sérieux ou dommages matériels.

MESURES PRÉVENTIVES:

• Ne pas utiliser de matériaux contenant des agents de

blanchiment ou du chlore.

• Ne pas utiliser des solvants à base d’hydrocarbure

halogéné tels que l’agent anticryptogamique, le chlorure

de méthylène et le trichloro-éthane-1,1,1. Ces produits ne

sont pas compatibles avec l’aluminium

• Communiquer avec votre fournisseur de revêtement pour

connaître la compatibilité du matériau avec l’aluminium.

DANGER: VAPEURS NOCIVES – la peinture, les solvants,

les insecticides et autres matériaux peuvent

être nocifs lorsqu’ils sont inhalés ou en contact

avec le corps. Les vapeurs peuvent causer une

nausée importante, des évanouissements ou

un empoisonnement.

MESURES PRÉVENTIVES:

• Utiliser un respirateur ou un masque chaque fois qu'il y a

des risques d'inhalation de vapeurs. Lire attentivement

toutes les instructions se rapportant au masque pour

vérifier que celui-ci vous assure une protection suffisante

contre les vapeurs toxiques.

• Porter des lunettes de protection.

• Porter des vêtements de protection, conformément aux

directives du fabricant de revêtement.

DANGER: GÉNÉRALITÉS - Peut causer des dommages

matériels ou corporels sérieux.

MESURES PRÉVENTIVES:

•Avant d'utiliser tout équipement, lire attentivement toutes

les instructions et les consignes de sécurité

•Toujours débrancher le moteur de l’alimentation électrique

avant d’effectuer des travaux sur l’appareil.

• Se conformer à la législation locale, provinciale ou fédérale

pour tout ce qui concerne la ventilation, la prévention des

incendies et les conditions générales d'utilisation.

• Les normes de sécurité du Gouvernement américain sont

régies par le Occupational Safety and Health Act (OSHA).

Il est important de consulter ces normes, en particulier la

section 1910 sur le normes générales et la section 1926

sur les des normes de la construction.

• N’utiliser que les pièces autorisées par le fabricant.

L’utilisateur assume tous les risques et responsabilités

lorsqu’il utilise des pièces qui ne sont pas conformes aux

caractéristiques techniques minimales ainsi qu’aux

dispositifs de sécurité du fabricant de la pompe.

• Vérifier, avant toute utilisation, que les flexibles ne

présentent pas d'entaille ou de fuite, que le couvercle ne

soit pas gonflé et que les raccords ne soient pas

endommagés. Si le flexible a subi l'un des dommages

précités, remplacez-le immédiatement. Ne jamais réparer

un flexible d'alimentation en peinture. Le remplacer par un

autre flexible mis à la terre.

•Tout flexible, raccord orientable, pistolet et accessoire

utilisé avec cet appareil doit pouvoir fonctionner à une

pression égale ou supérieure à 3 200 lb/po2 / 22.8 MPa.

• Ne jamais pulvériser lorsqu'il vente.

• Porter des vêtements pour protéger la peau et les

cheveux contre tout contact avec la peinture.

Sécurité des moteurs à essence

Les produits chimiques contenus dans les vapeurs

d'échappement de cet appareil sont reconnus par l'État de

la Californie (États-Unis) comme étant cancérigènes. Ils

peuvent également entraîner des anomalies congénitales

ou d’autres dangers pour la santé.

1. Les moteurs Honda sont conçus pour fonctionner en toute

sécurité et avec une fiabilité maximale s'ils sont utilisés

conformément aux instructions. Veuillez lire et

comprendre le manuel de l’utilisateur de Honda avant de

faire fonctionner le moteur. Le non-respect de ces

consignes peut entraîner des dommages matériels ou des

blessures physiques graves.

2. Pour éviter tout risque d'incendie et fournir une ventilation

adéquate, placez le moteur à une distance minimale de 1

mètre (3 pieds) des immeubles et d'autres équipements

pendant son fonctionnement. Ne placez pas d'objets

inflammables à côté du moteur.

3. Tenez les enfants et les animaux domestiques à l'écart de

la zone de travail; vous éviterez ainsi tout risque de

brûlures sur les pièces chaudes du moteur et de

blessures entraînées par les accessoires utilisés par le

moteur pour son fonctionnement.

4. Sachez comment arrêter rapidement le moteur, et

assurez-vous que vous avez bien compris le

fonctionnement de toutes les commandes. Ne permettez

jamais à une personne de faire fonctionner le moteur sans

connaître les instructions nécessaires.

5. L'essence est extrêmement inflammable et explosive dans

certaines conditions.

6. Remplissez le réservoir de carburant dans une zone bien

ventilée, moteur arrêté. Ne fumez pas et évitez toutes

flammes ou étincelles dans la zone de remplissage de

carburant ou dans une zone de stockage du carburant.

7. Veillez à ne pas faire déborder le réservoir de carburant.

Après remplissage, assurez-vous que le bouchon du

réservoir est solidement vissé.

8. Faites attention à ne pas renverser de carburant lors du

remplissage du réservoir. Les vapeurs ou les

éclaboussures de carburant peuvent s'enflammer. En cas

d'éclaboussures, assurez-vous que la zone est bien sèche

avant de faire démarrer le moteur.

9. Ne faites jamais fonctionner le moteur dans un endroit

fermé ou confiné. Les fumées d'échappement

contiennent du monoxyde de carbone qui est un gaz

toxique; une exposition prolongée peut entraîner une

perte de conscience et peut s'avérer mortelle.

10. Le silencieux devient très chaud pendant le

fonctionnement et reste chaud quelque temps après l’arrêt

du moteur. Faites attention à ne pas toucher le silencieux

tant qu'il est chaud. Pour éviter des brûlures graves ou

des risques d'incendie, laissez le moteur refroidir avant de

le transporter ou de le ranger à l'intérieur.

11. Ne transportez jamais le moteur si le réservoir est plein.

AVERTISSEMENT

Français

Precauciones de seguridad

Este manual contiene información que debe leer y comprender

antes de usar el equipo. Cuando se encuentre con uno de los

siguientes símbolos, asegúrese de observar sus indicaciones

de seguridad.

Este símbolo indica la existencia de un peligro potencial que

puede causar lesiones graves o la muerte. Después del

mismo se incluye información de seguridad importante.

Este símbolo indica la existencia de un peligro potencial para

usted o el equipo. Después del mismo se incluye información

importante que indica la forma de evitar daños al equipo o la

forma de prevenir lesiones menores.

PELIGRO: LESIÓN POR INYECCIÓN - La corriente de

pintura de alta presión que produce este

equipo puede perforar la piel y tejidos

subyacentes, lo que conduciría a lesiones

serias y una posible amputación. Consulte de

inmediato a un médico.

NO TRATE LAS LESIONES POR INYECCIÓN COMO SI

FUERAN SIMPLES CORTADAS! Una inyección puede

conducir a una amputación. Consulte de inmediato a un

médico.

El rango de operación máximo de la unidad es 3300 PSI /

22.8 MPa de presión de fluidos.

PARA PREVENIR:

• NO dirija NUNCA la punta de la pistola hacia alguna parte

del cuerpo.

• NO permita NUNCA que alguna parte del cuerpo tenga

contacto con la corriente del fluido. EVITE tener contacto

con corrientes de fluido que salgan de fugas que haya en

la manguera.

• NO ponga NUNCA la mano enfrente de la manguera. Los

guantes no ofrecen ninguna protección contra lesiones

por inyección.

• Bloquee SIEMPRE el gatillo de la pistola, apague la

bomba de fluido y libere toda la presión antes de dar

mantenimiento, limpiar el protector de la boquilla, cambiar

la boquilla o dejar desatendido el equipo. La presión no

se liberará al apagar el motor. Para liberar la presión

debe girarse la perilla PRIME/SPRAY (cebar/atomizar)

hasta la posición PRIME. Consulte el PROCEDIMIENTO

PARA LIBERAR LA PRESIÓN que se describe en este

manual.

• Mantenga puesto SIEMPRE el protector de la boquilla

mientras atomice. El protector de la boquilla ofrece cierta

protección contra lesiones por inyección pero es

principalmente un dispositivo de advertencia.

• Quite SIEMPRE la boquilla del atomizador antes de

enjuagar o limpiar el sistema.

• Pueden desarrollarse fugas en la manguera de pintura

por causa del desgaste, retorcimientos o el abuso. Una

fuga es capaz de inyectar el material en la piel. Cada vez

que use la manguera de pintura, inspecciónela antes.

• NO use nunca una pistola de atomización que no tenga

un bloqueador o un protector de gatillo puesto y que

funcione.

•Todos los accesorios deben tener una capacidad de 3300

lb/pulg2 / 22.8 MPa o mayor. Esto incluye las boquillas

de atomizador, pistolas, extensiones y mangueras.

ADVERTENCIA

NOTA: los avisos contienen información importante,

présteles especial atención.

PRECAUCION

ADVERTENCIA

PELIGRO: EXPLOSIÓN O INCENDIO - Los vapores de

solventes y pintura pueden explotar o

incendiarse, causando con esto lesiones

severas y/o daños en la propiedad.

PARA PREVENIR:

• Debe proveerse un escape y aire fresco para hacer que el

aire que está dentro del área de atomización se mantenga

libre de acumulaciones de vapores inflamables.

• Evite todas las fuentes de ignición como son las chispas

electrostáticas, llamas abiertas, flamas de piloto, objetos

calientes, cigarros, y chispas que se generan al conectar

y desconectar las extensiones o de apagadores de luz

que estén funcionando.

• No fume en la zona de trabajo.

• Debe haber un equipo para extinguir incendios

permanentemente y en buenas condiciones.

• Coloque la bomba para pintar a un mínimo de 1 m (de

preferencia más) en una habitación aparte, bien ventilada,

alejada del objeto que va a pintar o a por lo menos 6 m

de dicho objeto, en una zona bien ventilada (utilice una

manguera más larga, si es necesario). Los gases

inflamables a menudo son más pesados que el aire. La

zona del piso debe tener la debida ventilación. La bomba

para pintar contiene piezas que forman arcos que emiten

chispas y pueden encender los gases.

• El equipo que se utilice, así como los objetos que estén

dentro y alrededor del área de atomización, deben

conectarse a tierra de manera apropiada para prevenir las

descargas eléctricas y las chispas.

• Use solamente mangueras para fluidos de alta presión,

conductoras o conectadas a tierra, para aplicaciones sin

aire. Asegúrese de que la pistola esté conectada a tierra

de manera apropiada, mediante conexiones de

manguera.

• El cable de alimentación debe enchufarse a un circuito

aterrado.

• Siempre enjuague la unidad en un recipiente de metal por

separado, con presión baja en la bomba y sin la boquilla.

Sostenga la pistola firmemente contra el recipiente para

ponerlo a tierra y evitar chispas estáticas.

• Siga las advertencias y avisos de seguridad del fabricante

de los materiales y solventes.

•Tenga muchísimo cuidado al usar materiales cuyo punto

de ignición sea inferior a 70° F (21° C). El punto de

ignición es la temperatura a la cual pueden encenderse

los vapores emanados por un fluido al exponerlos a

llamas o chispas.

• El plástico puede causar chispas estáticas. Nunca

cuelgue plástico en las ventanas ni en las puertas del

área donde va a pintar. No utilice plástico para proteger

el piso cuando pinte materiales inflamables.

• Cuando enjuague el equipo utilice la presión más baja

posible.

MOTOR DE GAS (SEGÚN CORRESPONDA)

Coloque siempre la bomba fuera del edificio, al aire libre.

Mantenga todo solvente alejado del escape del motor. Nunca

llene el tanque de combustible si el motor está encendido o

caliente. La superficie caliente puede encender el combustible

derramado. Conecte siempre un conductor de tierra desde la

unidad de la bomba a un objeto puesto a tierra, por ejemplo

una tubería de agua metálica. Consulte el manual del motor

para obtener información completa de seguridad.

NOTA PARA EL MÉDICO: La inyección dentro de la piel

es una lesión traumática. Es importante que la lesión

se trate quirúrgicamente tan pronto como sea posible .

NO retrase el tratamiento por investigar la toxicidad.

La toxicidad es motivo de preocupación con algunos

revestimientos que se inyectan directamente en la

corriente sanguínea. Es recomendable consultar a un

cirujano plástico o reconstructor de manos.

Español

PELIGRO: PELIGRO DE EXPLOSIÓN DEBIDO A

MATERIALES INCOMPATIBLES - Podría

causar lesiones severas o daños en la

propiedad.

PARA PREVENIR:

• No utilice materiales que contengan blanqueador o cloro.

• No use solventes con hidrocarburos halogenados, tales

como productos para eliminar el moho, cloruro de

metileno y 1,1,1 - tricloroetano. Estos no son compatibles

con el aluminio.

• Comuníquese con el proveedor del producto para obtener

información de compatibilidad con materiales de aluminio.

PELIGRO: GASES PELIGROSOS - Las pinturas, solventes,

insecticidas y otros materiales pueden ser

perjudiciales si se inhalan o entran en contacto

con el cuerpo. Los gases pueden causar

náusea, desmayos o envenenamiento graves.

PARA PREVENIR:

• Use una mascarilla respiratoria o careta siempre que

exista la posibilidad de que se puedan inhalar vapores.

Lea todas las intrucciones que vengan con la careta para

estar seguro de que se tendrá la protección necesaria

contra la inhalación de vapores dañinos.

• Use gafas protectoras.

• Use ropa de protección, según lo requiera el fabricante

del producto.

PELIGRO: GENERAL - Puede causar daños en la

propiedad o lesiones severas.

PARA PREVENIR:

• Lea todas las instrucciones y advertencias de seguridad

antes de hacer funcionar cualquier equipo.

• Desconecte siempre el motor del suministro eléctrico

antes de dar servicio al equipo.

• Observe todos los códigos locales, estatales y nacionales

apropiados que rigen las medidas de ventilación,

prevención de incendios y operación.

• Los Estándares de Seguridad del Gobierno de los

Estados Unidos se han adoptado bajo el Acta de

Seguridad y Salud Ocupacionales (OSHA por sus siglas

en inglés). Deben consultarse estos estándares,

particularmente la parte 1910 de los Estándares

Generales y la parte 1926 de los Estándares de la

Construcción.

• Utilice únicamente piezas autorizadas por el fabricante.

El usuario asume todos los riesgos y responsabilidades si

usa piezas que no cumplen con las especificaciones

mínimas y dispositivos de seguridad del fabricante de la

bomba.

• Antes de usarla cada vez, revise todas las mangueras para

ver que no tengan cortadas, fugas, una cubierta desgastada

por abrasión o con abolladuras, así como uniones dañadas

o que se hayan movido. Si existiera cualquiera de estas

condiciones, reemplace la manguera inmediatamente. No

repare nunca una manguera de pintura. Reemplácela con

otra manguera conectada a tierra.

•Todas las mangueras, soportes giratorios, pistolas y

accesorios que se usen con esta unidad deben tener una

capacidad de presión de 3300 lb/pulg2 / 22.8 MPa o

mayor.

• No atomice en días con viento.

• Use ropa que evite el contacto de la pintura con la piel y

el cabello.

Seguridad del motor de gasolina

El escape del motor de esta unidad contiene productos

químicos que el Estado de California reconoce que

causan cáncer, defectos congénitos u otros daños a la

reproducción.

1. Los motores Honda han sido diseñados para ofrecer un

servicio seguro y fiable, si son manejados de acuerdo con

las instrucciones. Lea y comprenda el Manual del

Propietario de Honda antes de hacer funcionar el motor.

Si no hace esto, podrían producirse lesiones personales o

daños en el equipo.

2. Para evitar riesgos de incendio y proporcionar una

ventilación adecuada, mantenga el motor como mínimo a

1 metro (tres pies) de edificios y de otros equipos durante

su funcionamiento. No coloque objetos inflamables cerca

del motor.

3. Los niños y los animales de compañía deben mantenerse

alejados del área de trabajo, debido a la posibilidad de

quemaduras producidas por los componentes calientes

del motor o de daños producidos por el equipo al que

haga funcionar el motor.

4. Conozca el modo de detener rápidamente el motor, y

entienda el funcionamiento de todos los controles. No

permita que nadie haga funcionar el motor sin las

instrucciones adecuadas.

5. La gasolina es extremadamente inflamable y es explosiva

en determinadas circunstancias.

6. Reabastézcase de combustible en una zona bien

ventilada y con el motor apagado. No fume ni permita

que haya llamas ni chispas en el área de

reabastecimiento de combustible ni donde se almacene la

gasolina.

7. No llene excesivamente el tanque de combustible. Tras

repostar, asegúrese de que la tapa del tanque está

adecuadamente cerrada y asegurada.

8. Tenga cuidado de no derramar combustible cuando

realice el reabastecimiento. Los vapores del combustible

o el combustible derramado pueden inflamarse. Si se

derrama combustible, asegúrese de que el área esté seca

antes de arrancar el motor.

9. Nunca haga funcionar el motor en un área cerrada o

reducida. Los gases de escape contienen monóxido de

carbono tóxico: su exposición puede causar la pérdida del

conocimiento y puede originar la muerte.

10. El silenciador se calienta mucho durante el

funcionamiento y permanece caliente durante un tiempo

después de que el motor esté parado. Tenga cuidado de

no tocar el silenciador mientras está caliente. Para evitar

quemaduras graves o riesgos de incendio, deje que el

motor se enfríe antes de transportarlo o almacenarlo en el

interior.

11. Nunca transporte una unidad con gasolina en el tanque.

ADVERTENCIA

Español

Parts List

Main Assembly

Item Part # Description Quantity

1 0509550 Hex screw...................................................4

2 ---------- Engine, 5.5 HP ...........................................1

3 ---------- Drive assembly ...........................................1

4 0509635 Screw..........................................................1

5 0509634 Port plug .....................................................1

6 0509627 Controller cover ..........................................1

7 0509939 Front cover w/ label ....................................1

8 0509552 Screw..........................................................4

9 0509520 Connecting pin............................................1

10 0509521 Retaining ring..............................................1

11 0509144 Fluid section assembly ...............................1

12 0509651 Siphon tube.................................................1

13 0507783 Hose clip.....................................................1

Item

Part # Description Quantity

14 5006536 Inlet screen .................................................1

15 ---------- Filter assembly............................................1

16 0509176 Outlet cap assembly...................................1

17 0508343 Fitting, 3/8”..................................................1

18 ---------- Cart assembly.............................................1

19 0509551 Lock nut ......................................................4

20 0507786 Lock washer................................................2

21 0507787 Hex screw...................................................2

22 0509553 Screw..........................................................2

23 0509928 Grounding cable .........................................1

24 0507785 Return hose (not shown) ............................1

25 0507387 Hose, high pressure (not shown) ...............1

Item Part # Description Quantity

1 9850936 ON/OFF switch ...........................................1

2 0509558 Electronic pressure control assembly.........1

3 0509556 Screw..........................................................4

4 0507973 Potentiometer .............................................1

5 9800340 Ground screw .............................................1

6 0509495 Gasket ........................................................1

7 0509562 Ball..............................................................2

8 0509564 Gear assembly............................................1

9 0509559 Thrust washer.............................................1

10 0509153 Pump housing.............................................1

11 0509155 Slider assembly ..........................................1

12 0509541 Washer........................................................4

13 0509539 Socket screw, 2.25” ....................................2

14 0509540 Socket screw, 2” .........................................2

15 0509561 Socket screw ..............................................4

16 53171 Lock washer................................................4

17 0509157 Slider housing.............................................1

18 0509565 Retaining ring..............................................1

19 0509567 Drive shaft assembly ..................................1

20 0509572 Clutch field assembly..................................1

21 0507748 Cap .............................................................1

Item

Part # Description Quantity

22 0507740 Pressure control knob.................................1

23 0507749 Seal nut.......................................................1

24 0509557 Mounting plate ............................................1

25 0507784 Grommet, 7/16”...........................................1

26 0509531 Grommet, liquid tight ..................................1

27 0509136 Gear housing ..............................................1

28 0509573 Set screw....................................................6

29 0509563 Thrust bearing.............................................1

30 0509574 Plug.............................................................1

31 0509538 Screw..........................................................4

32 0509922 Clutch housing............................................1

33 0509619 Clutch hub...................................................1

34 0509570 Clutch hub and armature

(includes items 28(2), 33, and 35)..............1

35 0509571 Taper lock bushing (includes item 28(2))....1

36 0509566 Socket screw ..............................................3

37 0295694 Lock washer................................................3

38 0509568 Clutch rotor .................................................1

39 0291329 Engine, 5.5 HP ...........................................1

40 0509569 Hex screw...................................................4

41 0507786 Lock washer................................................4

NOTE: All electrical work should be performed by a

Spraytech authorized service center.

Drive Assembly

Fluid Section Assembly (P/N 0509144)

Install lower packing with

large beveled edge

facing up.

Install upper packing

with large beveled

edge facing down.

Large Beveled Edge

Item Part # Description Quantity

1 0509536 Upper seal retainer .....................................1

2 0509430 Adapter ring ................................................1

3 0509935 Upper packing assembly ............................1

4 0509505 Jam nut.......................................................1

5 0509709 Fitting ..........................................................1

6 0509937 Cylinder.......................................................1

7 0509936 Lower packing assembly ............................1

8 0509527 Lower support ring......................................1

9 0509683 Seal washer................................................1

10 0509938 Piston..........................................................1

11 0509648 Outlet valve seal.........................................1

12 0509601 Outlet cage .................................................1

13 0509710 Outlet valve ball..........................................1

14 0507454 Nylon washer..............................................1

15 0509655 Outlet valve seat.........................................1

16 0507733 Outlet valve retainer ...................................1

17 0509602 Inlet cage ....................................................1

18 0509707 Inlet valve ball.............................................1

19 0509623 Inlet valve seat............................................1

20 0509708 O-ring, PTFE ..............................................1

21 0509652 Viton o-ring .................................................1

22 0509653 Back-up ring, PTFE ....................................1

23 0509533 Foot valve ...................................................1

24 0509148 Piston assembly

(includes items 10–16) ...............................1

0509940 Repacking kit (includes items 2, 3, 7, 9, 11,

13, 14, 18, 20, 21, 22,

0509934 Lower packing insertion tool

NOTE: When repacking the fluid section, make sure

the raised lip on the bottom of the lower

packing is fully outside the packing around

the piston rod after insertion of the piston rod.

Cart Assembly

Item Part # Description Quantity

1 0507766 Handle (includes items 2–5, 10, and 11)....1

2 9841504 Snap button ................................................2

3 0295609 Handle washer............................................2

4 0295610 Roll pin........................................................2

5 0295607 Handle sleeve.............................................2

6 0507784 Grommet.....................................................3

7 0509625 Axle cap......................................................2

8 0509626 Wheel spacer..............................................2

9 9885571 Plug.............................................................2

10 0295606 Lock washer................................................4

11 0295608 Screw..........................................................4

12 0509575 Cart (includes item 9) .................................1

13 0509624 Wheel .........................................................2

Filter Assembly

Item

Part # Description Quantity

1 0294124 Filter body...................................................1

2 14069 Filter, 50 mesh ............................................1

3 9894245 Core spring .................................................1

4 14072 O-ring, PTFE ..............................................1

5 0507737 Transducer..................................................1

6 0509738 Outlet fitting, 3/8” ........................................1

7 5000527 Outlet fitting, 1/4” ........................................1

8 0507738 Plug, 1/4” ....................................................1

9 0509522 Filter housing ..............................................1

10 0507690 PRIME/SPRAY valve assembly..................1

PRIME/SPRAY Valve Assembly

(P/N 0507690)

Item Part # Description Quantity

1 0507736 Dowel pin....................................................1

2 0507745 Gasket ........................................................1

3 5000529 O-ring, PTFE ..............................................1

4 0507741 O-ring, Viton................................................1

5 0507744 Valve housing .............................................1

6 0507746 Valve seat ...................................................1

7 0507743 Valve stem ..................................................1

8 5006547 O-ring, Viton................................................1

9 0507747 Spring .........................................................1

10 0507742 Valve retainer..............................................1

11 0507735 Cam base ...................................................1

12 5006543 Groove pin ..................................................1

13 0507662 Valve handle ...............................................1

Electrical Schematic

Labels

Part # Description

0509820 Logo label, front

0295840 Warning label, explosion

0295841 Warning label, injection

0295805 Shock hazard label

0509819 “No Oil” label

0089799

Potentiometer

0507973

Transducer

0507737

E.P.C. Board

0509739

0509549

Switch

9850936

Engine

0509548

Clutch

Clutch Clutch

Switch

White

Notes

Limited Warranty

Commercial Airless Spray Equipment

Two Year Warranty

SprayTECH, a division of Wagner Spray Tech Corporation ("SprayTECH"), warrants this product against defects in material and

workmanship for a period of two years following the date of purchase by the original purchaser. During that period, SprayTECH

will repair or replace any defective or worn-out component or, at SprayTECH’s option, refund to the original purchaser the full

purchase price for the product in exchange for the return of that product. However, SprayTECH will not replace or repair any fluid

pump component on account of wear more than once during the two year warranty period. This warranty does not cover

consumable products such as filters and tips.

Lifetime Warranty on Gear Trains, Electric Motors, and Gas Engines

SprayTECH warrants any gear train, electric motor (excluding brushes) and gas engine (excluding the clutch) in this product

against defects in material and workmanship for the lifetime of the original purchaser. If SprayTECH determines that the

foregoing warranty has been breached, SprayTECH will repair or replace the defective components without charge or, at

SprayTECH’s option, refund to the original purchaser the full purchase price for the product in exchange for the return of that

product.

Warranty Claims

Any request for repair or replacement pursuant to the warranties above must be accompanied by the return of the applicable

parts, with transportation charges prepaid, to a service center authorized by SprayTECH or to Wagner Spray Tech Corporation,

1770 Fernbrook Lane, Minneapolis, MN 55447.

Limitation of Remedies

THE REMEDIES SET FORTH ABOVE ARE THE EXCLUSIVE REMEDIES AVAILABLE FOR BREACH OF EXPRESS AND

IMPLIED WARRANTIES. These remedies shall not be deemed to have failed of their essential purpose so long as SprayTECH

is willing to repair or replace parts, or to refund the purchase price, as set forth above.

What Is Not Covered By This Warranty

This warranty does not cover defects or damages caused by:

•the use or installation of repair or replacement parts or accessories not manufactured by SprayTECH;

• repair performed by anyone other than a SprayTECH Authorized Service Center; or

• abuse, misuse, negligence, accident, faulty installation or tampering in a manner which impairs normal operation.

This warranty also does not cover equipment and accessories supplied to SprayTECH from an original equipment manufacturer,

including but not limited to hoses, tips, and accessories. SprayTECH will provide the purchaser with copies of the original

equipment manufacturer’s express warranties provided to SprayTECH along with the name and address of the appropriate

manufacturer.

Limitation of Remedies

IN NO CASE SHALL SPRAYTECH BE LIABLE FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR LOSS,

INCLUDING TRANSPORTATION COSTS, WHETHER SUCH DAMAGES ARE BASED UPON A BREACH OF EXPRESS OR

IMPLIED WARRANTIES, BREACH OF CONTRACT, NEGLIGENCE, STRICT TORT, OR ANY OTHER LEGAL THEORY.

Disclaimer of Implied Warranties

THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT

NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

No Ability To Transfer

This warranty is extended to the original purchaser only and is not transferable.

1770 Fernbrook Lane

Minneapolis, Minnesota 55447

Telephone 1-800-292-4637

SprayTECH 30-Day Satisfaction Guarantee

If, within a 30-day period from the date of purchase, you are not totally satisfied with a SprayTECH/CAPSpray unit, you

may return it for full credit toward another SprayTECH or CAPSpray product of equal or greater value.

Material Safety Data Sheets (MSDS) are available on SprayTECH’s website or by calling Technical Service.

Titan GPX1600 El manual del propietario

Marca: Titan

Modelo: GPX1600

Categoría: Rociador de pintura

Tipo: El manual del propietario

Descargar PDF

informe

En otros idiomas

français: Titan GPX1600 Le manuel du propriétaire
English: Titan GPX1600 Owner's manual

Titan GPX1600 El manual del propietario

Titan GPX1600 El manual del propietario

En otros idiomas

Documentos relacionados

Otros documentos