Yamaha RS-100 El manual del propietario

Categoría
Tambores musicales
Tipo
El manual del propietario

Este manual también es adecuado para

H
G
RS100
M
L
K
J
F
E
D
I
N
C
B
A
y u o !0i
!2!1
trewq
q
w
u
r
y
!2
!1
e
D
E
F
G
J
J
o
I
G
G
G
H
!0
i
A
B
C
1
A
B
D
E
3
H
C
G
H
H
G
H
2
B
C
F
K
D
A
B
4
G
G
G
5
A
B
J
E
C
F
G
H
G
G
G
J
L
H
G
Electronic Drum Rack System
RS100
Assembly Instruction
Side Assembly A (x1)
M
L
K
J
F
E
D
I
N
* Specifications are subject to change without notice.
Before using, please read this “Assembly Instruction” sheet,
and use this product in a safe and proper manner.
Especially for children, parents or an instructor should teach the
children the proper manner in which to use the device.
Caution (including danger, or warning). This mark indicates
cautions in which you should pay close attention to.
Acts indicated with this icon are prohibited and should not
be attempted.
This icon indicates acts that you are urged to follow.
Thank you for purchasing the Yamaha Electronic Drum Rack System RS100.
Before using, thoroughly read this assembly manual, and use this product safely and correctly.
RS100 Rack Stand Parts
* Before assembling the rack stand, make sure all of the parts shown below are included.
Side Assembly B (x1) Side Assembly C (x1)
Center Pipe Assembly A (x1) Center Pipe Assembly B (x1) Side Arm (x1)
Tom Holder (x5)
Module Holder (x1)
(4 screws included)
Module Holder Clamp (x1)
Assembly Instruction
(this sheet)
Tuning Key (x1)
Cable Band
(x10)
Cymbal Holder (x2) Felt Washer (x2)
* Specifications are subject to change without notice.
Always set the instrument on a flat and solid surface.
Placement on a sloping, unstable surface or on steps
may result in the instrument being unstable and over-
turning.
Make sure all bolts are tightened firmly. Loose bolts
may result in the rack overturning or parts dropping
causing injury.
When adjusting the height or angle, do not suddenly
loosen the bolt. The pad may drop, the rack or pipes
may slip, pinching or causing injury to hands or fingers.
Do not sit or step on the rack. The rack may overturn
or be damaged resulting in injury.
Please be careful when children are close to or touch-
ing the product. The product has many pipes and arms
so careless movement around the product may result
in injury.
When setting the pads and modules, please pay close
attention in regards to the handling and setting of
cables. Feet may become entangled in the cables re-
sulting in falls.
If this symbol is ignored and the equipment is
used improperly, fatal injury to persons or se-
rious damage could occur.
Do not put your hands or feet under the foot pedal or
foot switch. They may be pinched resulting in injury.
Watch your fingers when adjusting clamps. They may
become pinched resulting in injury.
Be careful around pipe ends, inside the pipe and screw
ends. Metal shavings, etc. may injure your fingers.
Do not attach acoustic drums to the electronic drum
rack. Clamps may be damaged and drums may drop,
causing injury.
If this symbol is ignored and the equipment is
used improperly, there is a danger of injury to
persons handling the equipment, and material
damage could occur.
CAUTION
WARNING
C
B
A
RS100+Pad Grouping: Setup Example
Pad and Drum Trigger Grouping (option)
q
w
u
r
y
!2
!1
e
D
E
F
G
J
J
o
I
G
G
G
H
!0
i
qDTXTREME
Drum Trigger Module
yTP80S/TP80
Drum Pad
!1Snare Stand
*SS-642 etc.
uPCY80S/PCY80
Cymbal Pad
iPCY10
Trigger Pad
!2Foot Pedal
*DFP-880 etc.
oKP120
Real Head Kick Pad
!0HH80A
Hi-hat Control Pedal
TPCL100
Tom Holder
CYAT100
Cymbal Attachment
tRHP80
Real Head Pad (8inch)
rRHP100
Real Head Pad (10inch)
eRHP120
Real Head Pad (12inch)
wRHP120SD
Snare Type Real Head Pad
(12inch)
Please use for additional pads.
* Please use a snare stand for setting the snare drum pad.
Includes Holder Clamp Assembly.
C
B
A
RS100 Assembly
* A screw driver (+ or -) is necessary to complete the assembly.
1
3
2
4
5
DTXTREME
Tilter
Center Pipe Assembly A
D
Tighten
Side Assembly C
C
Side Arm
F
Side Assembly B
B
Center Pipe Assembly B
E
Side Assembly A
A
Tom Holder
G
Module Holder
Clamp
Module Holder
H
Step 3-4
Step 3-3
Step 3-2
Step 3-1
After the above assembly is complete, set the Kick Pad, Hi-Hat
Control pedal, etc. into position and connect the necessary
cables. To keep cable out of the way while playing, use the
supplied Cable Bands
K
to hold the cables to the rack system's
pipes.
Step 4-1
Step 4-1
Tom Holder
G
Tom Holder
G
Cymbal Pad
Tom Holder
G
Cymbal Holder
PCY10
Step 4-2
Step 5-1
Step 4-1
Step 4-2
Step 5-2
Cymbal Pad
Felt (Small)*
Felt (Large)*
Cymbal Holder
J
Washer*
Please make sure that the fixing bolts on each part, such as clamps, pads, etc. are firmly tightened.
Bolts that are too tight or too loose may result in damage to the part or the part dropping. Please use caution.
Attach the Center Pipe Assembly A
D
and the Center Pipe Assembly
B
E
to the upright pipes of the Side Assembly A
A
and Side Assem-
bly B
B
.
Attach the Side Arm
F
to the pipes of the side Assembly B
B
and the
Side Assembly C
C
.
Attach the Module Holder
H
3-1 Attach the Module Holder Clamp
I
to the pipe of the Side As
sembly C
C
.
3-2 Insert the Tom Holder
G
into the Module Holder Clamp
,
and tighten the fixing screw.
3-3 Attach the DTXTREME to the Module Holder
H
. Using a screw
driver and the supplied screws, attach the Module Holder
H
to
the screw holes on the bottom of the DTXTREME.
3-4 Attach the Module Holder
H
, with the DTXTREME attached, to
the Tom Holder
G
.
Attach the Tom Holders
G
4-1 Insert the Tom Holders
G
into the Holder Clamps, align and
tighten the fixing screws.
4-2 Check the position and attach the Real Head Pad, etc. to the Tom
Holder
G
. Align the pads and secure. (Refer to the Real Head
Pad’s Owner’s Manual on how to attach the pads.)
Attach the Cymbal Holders
J
5-1 Insert the Cymbal Attachments into the upright pipes of the Side
Assembly A
A
and Side Assembly B
B
, and tighten the wing
bolts.
5-2 Attach the Cymbal Pad to the Cymbal Holder
, align the pad
and secure.
Also, when the PCY10 is used, please use the parts shown in the
diagram below. (Refer to the Cymbal Pads Owners Manual on
how to attach the Cymbal Pad.)
Anti-swivel brace
(supplied with the
PCY80/80S)
Change to the felt
washer
L
.
When the PCY10 is used.
* The * indicates parts supplied with the PCY10.
* It is not necessary to use the tilter that is supplied with
the PCY10.
1 / 1

Yamaha RS-100 El manual del propietario

Categoría
Tambores musicales
Tipo
El manual del propietario
Este manual también es adecuado para