PPA P400 Electromagnet Manual de usuario

Marca: PPA

Modelo: P400 Electromagnet

Tipo: Manual de usuario

Este manual también es adecuado para

3. Apply silicone inside the glass handle,

position it on the glass door. Tighten

screws 1 and 2 to lock the positioning of

the glass handle during silicone curing.

(note enough for the glass handle not

to move, as it may be liable to damage

the glass);

5. Make sure that the block and blank

assembly is aligned and leveled, do

a manual test before energizing the

electromagnet;

6. Close the cover.

ELECTROMAGNET INSTALLATION WITH GLASS

HANDLE KIT IN 2 LEAF SLIDING DOORS

1. Remove the PPA electromagnet kit

nishing cover;

2. Apply silicone adhesive to the

EVA shield and stick it on the inside

on the glass handle;

3. Apply silicone inside the glass handle, position it on the glass door. Tighten

screws 1 and 2 to lock the positioning of the glass handle during silicone

curing. (note enough for the glass handle not to move, as it may be liable to

damage the glass);

4. Align and x the

electromagnet on the other leaf;

5. Make sure that the block and blank

assembly is aligned and leveled, do

a manual test before energizing the

electromagnet.

6. Close the cover

ELECTROMAGNET INSTALLATION WITH GLASS

HANDLE KIT IN 1 LEAF SWING DOORS

4. Align and x the

electromagnet on the stop;

1. Remove the PPA electromagnet

kit nishing cover;

2. Apply silicone adhesive to the

EVA shield and stick it on the inside

on the glass handle;

3. Apply silicone inside the glass handle, position it on the glass door. Tighten

screws 1 and 2 to lock the positioning of the glass handle during silicone

curing. (note enough for the glass handle not to move, as it may be liable to

damage the glass);

4. Align and secure the

electromagnet to the stop;

5. Make sure that the block and

blank assembly is aligned and

leveled, do a manual test before

energizing the electromagnet;

6. Close the cover

ELECTROMAGNET INSTALLATION WITH GLASS

HANDLE KIT IN TWO-LEAVE SWING DOORS

1. Remove the PPA electromagnet

kit nishing cover;

2. Apply silicone adhesive to the

EVA shield and stick it on the inside

on the glass handle;

3. Apply silicone inside the glass handle, position it on the glass door. Tighten

screws 1 and 2 to lock the positioning of the glass handle during silicone

curing. (note enough for the glass handle not to move, as it may be liable to

damage the glass);

4. Align and x the electromagnet

on the other leaf;

5. Make sure that the block and

blank assembly is aligned and

leveled, do a manual test before

energizing the electromagnet;

6. Close the cover.

Made by:

Motoppar Indústria e Comércio de Automatizadores Ltda

Av. Dr. Labieno da Costa Machado, 3526 - Distrito Industrial

Garça - SP - CEP 17406-200 - Brasil

CNPJ: 52.605.821/0001-55

www.ppa.com.br | +55 14 3407 1000

GENERAL TERMS AND CONDITIONS OF WARRANTY

MOTOPPAR, Indury and Commerce of Automatic Gate Operators Ltd.,

regiered with the CNPJ (National Regiry of Legal Entities) under Number

52.605.821/0001-55, located at 3526 Dr. Labieno da Coa Machado Avenue,

Indurial Dirict, Garça – SP – Brazil, Zip Code 17406-200, manufacturer of PPA

Products, hereby guarantees this product again design, manufacturing or

assembly defects and/or supportively as a result of material quality aws that

could make its intended use improper or inadequate, within a legal period of

ninety days from time of acquisition, provided that the inallation inructions

described in the inruction manual are observed.

Due to the credibility and tru placed on PPA products, we will add 275 more

days to the period mentioned above, reaching a warranty period of one year,

likewise counted from the time of acquisition proven by consumer through

proof of purchase (Cuomer Receipt).

In case of defect, within the warranty period, PPA responsibilities are rericted to

the repair or subitution of the product manufactured by the company, under

the following conditions:

1. Repair and readjument of equipment may only be carried out by PPA

Technical Assiance, which is qualied to open, remove, and subitute parts

or components, as well as repair defects covered by this warranty; thus, failure

on observing this guideline and the veried use of any non-original parts will

cause the resignation of this warranty on the part of the user;

2. The warranty will not extend to accessories such as cables, screw kit, xing

brackets, power supplies etc.;

3. Expenses for packaging, transportation and product reinallation will be sole

responsibility of the consumer;

4. The equipment mu be sent directly to the Company responsible for the

sale (manufacturer's representative), through the address contained in the

purchase invoice, properly packed, thus avoiding loss of the warranty;

5. Within the additional period of 275 days, visits and transportation in places

where authorized technical assiance is not available will be charged. The co

of transportation of the product and/or technician will be sole responsibility

of the consumer and

6. The subitution or repair of the product does not prolong the warranty time.

This warranty will be terminated if the product:

1. Is damaged by natural agents, such as atmospheric discharges, oods,

wildres, landslides etc.;

2. Is inalled in an improper electric power supply or if it is not according to any

of the inallation inructions displayed on the manual;

3. Shows defects caused by droppings, collisions or any other physical accident;

4. Shows signs of product violation or attempted repair by unauthorized

personnel;

5. Is not used for its intended purpose;

6. Is not used under normal conditions;

7. Is damaged by accessories or equipment connected to it.

Recommendation:

We recommend that both the inallation and the maintenance of the operator

to be performed by an authorized PPA technical service. If the product fails or

has an improper operation, seek an Authorized Technical Service to x it.

OVERVIEW

Congratulations on acquiring a product with all the quality, comfort, and

security only PPA can provide you with. PPA electromagnet (12 Vdc), uses

magnetic holding force as its operating principle. It has from 100 to 600 kg

(220 to 1322 lb) holding force, depending on the acquired model, and its

structure is made of steel sheets with surface treatment and electrostatic

coating, what provides the device with increased corrosion resistance, as

well as a better nish. The available colors (white, black and gray) endow the

device with a ne appearance and compatibility with several environments.

Its brackets make it possible to adapt the electromagnet to every kind of

installations, even the ones with up to 20-mm misalignments (≈ 0.79 in). It is

also compatible with all available Access Control systems.

PRODUCT

PPA electromagnet has been developed to be used in applications in glass,

wood, aluminum, or partitions.

Technical Specications

P100 P150 P200 P400 P600

Holding Force (KgF) 100 150 200 400 600

Voltage (VDC) 12 12 12 12 12

Rated Current (mA) 650 520 520 900 1350

Rated Power 7.8 W 7.2 W 7.2 W 11 W 16.5 W

Temperature 50°C 50°C 50°C 50°C 50°C

Weight without

brackets (Kg)

0.703 0.97 0.975 1.9 2.8 Kg

Size (HxWxD) in mm 134 x 107

x 48.5

164 x 107

x 48.5

164 x 107

x 48.5

306 x 107

x 48.5

430 x 107

x 48.5

NOTE: This product is available in carbon steel and stainless-steel

versions. The carbon steel version is available in white, gray, and black.

INSTALLATION PRECAUTIONS

NOTE: To use this product on a glass door (it is only used on single-

leaf doors) it is necessary to use a PPA glass handle holder.

PPA electromagnetic has magnetic holding force as its operating principle.

Its eciency is due to the contact of the surfaces of the Armature Plate

and the Electromagnet, which results in a Holding force of about from 100

to 600 kg (220 to 1322 lb), depending on the acquired model, whenever its

Displacement Eort occurs on the traction direction, not on the Shearing

direction. Some procedures must be followed for the proper functioning of

the product:

• The product is recommended for indoor environments

• It must be installed inwards the protected premises

• Product cannot undergo alterations such as: sanding, painting or even

suering deformation on the surface of the armature plate.

NOTES:

1. If the product purchased is the stainless-steel version, one must re-

move the protective lm.

2. If one notices that the door is opening easily, check if the electrical

current of the product is in accordance with the recommended spe-

cication and check if the armature plate is really aligned with the

electromagnet and if there has not been any type of deformation on

the armature plate.

ITEMS PROVIDED

312

CAPTIONS

1 – Electromagnet

2 – Armature Plate (Mounting Plate)

3 – L Bracket (Part ‘A’)

4 – L Bracket (Part ‘B’)

5 – L Bracket (Part ‘C’)

6 – Finishing cover

INSTALLATION

Applications:

• 1 leaf - Framed glass (Internal mounting): On this kind of installation,

the mounting plate is mounted on the ‘U’ Bracket and the electromagnet is

mounted on the ‘L’ Bracket, according to the picture.

Part ‘A’

(L Bracket)

Mounting Plate Glass

door

Bracket

Opening direction

Magnet

• 2 leaves - Solid (Wood) doors (Overlapping Installation): On this kind of

installation, the ‘L’ Bracket (Part ‘B’) is mounted on the wood door and the

‘L’ Bracket (Part ‘C’) is mounted on the mounting plate (armature plate). The

electromagnet is mounted on the ‘L’ Bracket (Part ‘A’), which is fastened to

the door header. Such procedure can be seen below:

Opening direction

Mounting Plate

Magnet

Part ‘A’

(L Bracket)

Part ‘C’

(L Bracket)

Part ‘B’

(L Bracket)

Solid

(wood) door

• 1 leaf - Framed Glass (Overlapping Installation): For premises where

the glass door is framed. The ‘L’ Bracket (Part ‘B’) is mounted on both the ‘L’

Bracket (Part ‘C’) and the ‘U’ bracket (which is fastened to the glass). The ‘L’

Bracket (Part ‘C’) is mounted on both the mounting plate (armature plate)

and the ‘L’ Bracket (Part ‘B’). The electromagnet is mounted on the ‘L’ Bracket

(Part ‘A’), which is fastened to the door header. Such procedure can be seen

below.

Opening direction

Part ‘A’

(L Bracket)

Part ‘B’ (L

Bracket)

U Bracket

Part ‘C’

(L Bracket)

Glass

door

Magnet

Mounting

Plate

• 2 leaves - Glass with glass (Overlapping Installation): For premises with

two glass doors, according to the picture. The ‘L’ Bracket (Part ‘B’) is mounted

on both the ‘L’ Bracket (Part ‘C’) and the ‘U’ bracket (which is fastened to the

glass). The mounting plate (armature plate) is mounted on ‘L’ Bracket (Part

‘C’). The electromagnet is mounted on the other ‘L’ Bracket (Part ‘A’), which is

fastened to the door header. Such procedure can be seen below.

Opening direction

Mounting

Plate

Part ‘A’

(L Bracket)

Magnet

U Bracket

Part ‘C’ (L

Bracket)

Part ‘B’

(L Bracket)

Glass

door

WIRING

The electromagnet can be adapted to any access control, as long as

technical requirements such as supply voltage and rated current are

followed. To keep the electromagnet in operation (magnetized) a Normally

Closed (NC) command feeding it is required. To turn o the electromagnet

(demagnetized), its supply must be interrupted (cut o).

NOTE: The product is endowed with an edge sensor to detect door

closure and check if the electromagnet block is magnetized.

CAPTIONS

1 – Sensor cables (NO contact)

2 – 12V external power supply (not provided)

3 – Example of relay contact connection of an access control:

• NO = Normally open

• CM = Common

• NC = Normally closed.

PPA ELECTROMAGNET

12V POWER

SUPPLY

SENSOR: The lock is endowed with a sensor for door signaling. Such sensor

changes the state from Normally Open (NO) to Normally Closed (NC), when

the Armature plate is correctly in contact with the Electromagnet and without

any obstruction, i.e., indicating the “closed (resting) door status”, which avoids

the use of external magnetic (door/window) sensors, and provides the

installer with ease of installation and wiring.

On the sensor contact you can turn on visual exit annunciator (trac light),

lights, among other peripherals such as door status indicators. Sensor

connection example:

EXEMPLO DE LIGAÇÃO DO SENSOR

NOTE: The external power supply and the peripheral are not provi-

ded, it is just a schematic of how to connect the sensor.

ELECTROMAGNET INSTALLATION WITH GLASS

HANDLE KIT IN 1-LEAF SLIDING DOORS

1. Remove the PPA electromagnet

kit nishing cover;

2. Apply silicone adhesive on the EVA

protection and stick it on the inside of

the glass handle;

P09519 - 03/2023

Rev. 4

Installation Guide

PPA ELECTROMAGNETS

WARNING

Do not use the device

without referring to this

manual first.

Armature

Plate

Electromagnet Holding Force

Shearing strength

TRAFFIC

LIGHT

LED

12V

SENSOR CABLE