Yamaha KX-W321 Manual de usuario

Marca: Yamaha

Modelo: KX-W321

Categoría: Reproductores de casete

Tipo: Manual de usuario

Este manual también es adecuado para

KX-W421

KX-W421

KX-W321

OWNER’S MANUAL

MODE D’EMPLOI

Natural Sound Stereo Cassette Deck

Platine à cassette stéréo de la série “Natural Sound”

NATURAL SOUND CASSETTE DECK KX-W421

DOLBY NR

OFF/ B/ C

REC LEVELBALANCEPLAY TRIM

PHONES

STANDBY/ON

MODE

O / p / ∏ / RELAY

PLAYBACK

DECK A

L R MIN MAX

—+

CLOSE % % CLOSE

DIRECTION RESETRESET DIRECTION

! ⁄

!⁄

MUTE/SEARCH

PLAYPLAY

REC/PAUSE

EJECT EJECT

NORMAL HIGH

DUBBING A # B

NATURAL SOUND CASSETTE DECK KX-W321

DOLBY NR

OFF/ B/ C

REC LEVEL

PHONES

STANDBY/ON

MODE

O / p / ∏ / RELAY

PLAYBACK

DECK A

RECORD/PLAYBACK

DECK B

MIN MAX

RECORD/PLAYBACK

DECK B

DIRECTION RESETRESET DIRECTION

! ⁄

!⁄

MUTE/SEARCH

REC/PAUSE

EJECT EJECT

NORMAL HIGH

DUBBING A # B

CLOSE % % CLOSE

PLAYPLAY

U C A

Thank you for purchasing this YAMAHA stereo cassette deck.

SAFETY INSTRUCTIONS

÷ Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert you to the presence of uninsulated

“dangerous voltage” within the product's

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert you to the presence

of important operating and maintenance

(servicing) instructions in the literature

accompanying the appliance.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

1 Read Instructions — All the safety and operating

instructions should be read before the unit is operated.

2 Retain Instructions — The safety and operating

instructions should be retained for future reference.

3 Heed Warnings — All warnings on the unit and in the

operating instructions should be adhered to.

4 Follow Instructions — All operating and other instructions

should be followed.

5 Water and Moisture — The unit should not be used near

water — for example, near a bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement, or near swimming

pool, etc.

6 Carts and Stands — The unit should be used only with a

cart or stand that is recommended by the manufacturer.

6A A unit and cart combination

should be moved with care. Quick

stops, excessive force, and uneven

surfaces may cause the unit and cart

combination to overturn.

7 Wall or Ceiling Mounting — The unit should be mounted

to a wall or ceiling only as recommended by the

manufacturer.

8 Ventilation — The unit should be situated so that its

location or position does not interfere with its proper

ventilation. For example, the unit should not be situated on a

bed, sofa, rug or similar surfaces that may block the

ventilation openings: or placed in a built-in installation, such

as a bookcase or cabinet that may impede the flow of air

through the ventilation openings.

9 Heat — The unit should be situated away from heat

sources such as radiators, stoves, or other units that

produce heat.

10 Power Sources — The unit should be connected to a

power supply only of the type described in the operating

instructions or as marked on the unit.

11 Power-Cord Protection — Power-supply cords should

be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

attention to receptacles, and the point where they exit from

the unit.

12 Cleaning — The unit should be cleaned only as

recommended by the manufacturer.

13 No Use Periods — The power cord of the unit should be

unplugged from the outlet when left unused for a long

period of time.

14 Object and Liquid Entry — Care should be taken so

that objects do not fall into and liquids not spilled into the

inside of the unit.

15 Damage Requiring Service — The unit should be

serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged;

B. Objects have fallen, or liquid has been spilled into the

unit; or

C. The unit has been exposed to rain; or

D. The unit does not appear to operate normally or exhibits

a marked change in performance; or

E. The unit has been dropped, or the cabinet damaged.

16 Servicing — The user should not attempt to service the

unit beyond those means described in the operating

instructions. All other servicing should be referred to

qualified service personnel.

17 Grounding or Polarization — The precautions should be

taken so that the grounding or polarization of the unit is not

defeated.

This unit is not disconnected from the AC power source

as long as it is connected to the wall outlet, even if the

unit itself is turned off. This state is called the standby

mode. In this state, the unit is designed to consume a

very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE.

ENGLISHFRANÇAISDEUTSCHSVENSKAITALIANOESPAÑOLDUTCH

CAUTION: READ THIS BEFORE OPERATING

YOUR UNIT.

1. This unit is a sophisticated stereo cassette deck. To ensure

proper operation for the best possible performance, please

read this manual carefully.

2. Choose the installation location of your unit carefully. Avoid

placing it in direct sunlight or close to source of heat. Also

avoid locations subject to vibration and excessive dust, heat,

cold or moisture. Keep it away from sources of hum such as

transformers or motors.

3. Do not open the cabinet as this may result in damage to the

deck or electrical shock. If a foreign object should get into

the deck, contact your local dealer.

4. When removing the power plug from the wall outlet, always

pull directly on the plug; never pull the cord itself.

5. Do not apply excessive force when operating switches and

knobs.

6. When moving the deck, be sure to first pull out the power

plug and remove all cords connecting the deck to other

equipment.

7. Do not attempt to clean this unit with chemical solvents as

this may damage the finish. Use a clean, dry cloth.

8. Never allow metallic items (e.g. screwdrivers, tools, etc.) to

come near the record/playback head assembly. Doing so

may not only scratch or damage the head’s mirror-smooth

finish, it may also change the magnetic characteristics of the

heads, causing a deterioration in reproduction quality.

9. Although the record/playback head used in this unit is a high

quality head with outstanding reproduction characteristics, it

can become dirty through the use of old tapes or from dust

accumulation over time. This can have a serious effect on

reproduction quality. Clean the heads regularly with one of

the commonly available head cleaners or with cleaning

solutions as explained later in this manual.

10. Be sure to read the “TROUBLESHOOTING” section of this

manual for advice on common operating errors before

concluding that your unit is faulty.

11. Keep this manual in a safe place for future reference.

12. Voltage Selector (General model only)

The voltage selector on the rear panel of this unit must

be set for your local mains voltage BEFORE plugging in

the AC mains supply. (Voltage selector adjustable

between 110/120/220/240 V AC.)

Note

Please check the copyright laws in your country to record from

records, compact discs, radio, etc. Recording of copyright

material may infringe copyright laws.

FOR CANADIAN CUSTOMERS

TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT AND FULLY

INSERT.

THIS CLASS B DIGITAL APPARATUS MEETS ALL

REQUIREMENTS OF THE CANADIAN

INTERFERENCE-CAUSING EQUIPMENT

REGULATIONS.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association's

Consumer Electronics Group want you to get the most out of

your equipment by playing it at a safe level. One that lets the

sound come through loud and clear without annoying blaring

or distortion – and, most importantly, without affecting your

sensitive hearing.

Since hearing damage from loud sounds

is often undetectable until it is too late,

YAMAHA and the Electronic Industries

Association's Consumer Electronics

Group recommend you avoid prolonged

exposure to excessive volume levels.

Want You

LISTENING

For A Lifetime

FCC INFORMATION (U.S.A.)

1.IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC, to

use the product.

2.IMPORTANT: When connecting this product to

accessories and/or another product use only high quality

shielded cables. Cables supplied with this product

MUST be used. Follow all installation instructions.

Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3.NOTE: This product has been tested and found to

comply with the requirements listed in FCC Regulations,

Part 15 for Class "B" digital devices. Compliance with

these requirements provides a reasonable level of

assurance that your use of this product in a residential

environment will not result in harmful interference with

other electronic devices. This equipment generates/uses

radio frequencies and, if not installed and used

according to the instructions found in the users manual,

may cause interference harmful to the operation of other

electronic devices. Compliance with FCC regulations

does not guarantee that interference will not occur in all

installations. If this product is found to be the source of

interference, which can be determined by turning the unit

"OFF" and "ON", please try to eliminate the problem by

using one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact your local retailer that is

authorized to distribute this type of product. If you

cannot locate the appropriate retailer, please contact

Yamaha Electronics Corp., U.S.A.

6660 Orangethorpe Ave, Buena Park, CA 90620

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

TABLE OF CONTENTS

FEATURES ......................................................................... 4

CONNECTIONS.................................................................. 5

NOTES ON THIS MANUAL ................................................ 5

PLAYBACK (Common to DECKs A and B)......................... 6

BASIC OPERATION........................................................ 6

SELECTION SEARCH .................................................... 8

RELAY PLAYBACK ......................................................... 9

PLAY TRIM CONTROL ADJUSTMENT (KX-W421 only) 9

RECORDING .................................................................... 10

BASIC OPERATION...................................................... 10

REC MUTE OPERATION.............................................. 12

REC RETURN OPERATION ......................................... 12

DUBBING (From DECK A to DECK B) ............................. 13

CASSETTE TAPES .......................................................... 14

MAINTENANCE ................................................................ 15

OPTIONAL REMOTE CONTROL TRANSMITTER .......... 15

TROUBLESHOOTING ...................................................... 16

SPECIFICATIONS ............................................................ 17

FEATURES

÷ High Quality Hard Permalloy Recording/Playback Head in

Deck B and Playback Head in Deck A

÷ Dolby B/C Noise Reduction

÷ Play Trim Control for improved playback compatibility with

other decks (KX-W421 only)

÷ Auto Tape Selector

÷ Dolby HX Pro Dynamic Bias Servo (KX-W421 only)

÷ Relay Playback from DECK A to DECK B

÷ Selection Search

÷ Recording Mute Function

÷ Rec Return Operation

÷ Easy Dubbing Operation at Selectable Speed (Normal/

High)

÷ Peak Level Meters with Peak Hold Function

÷ Remote Control Capability with Optional Remote Control

Transmitter

Dolby noise reduction and HX Pro headroom extension

manufactured under license from Dolby Laboratories

Licensing Corporation. HX Pro originated by Bang &

Olufsen.

“DOLBY”, the double-D symbol

and “HX PRO” are

trademarks of Dolby Laboratories Licensing Corporation.

ENGLISHFRANÇAISDEUTSCHSVENSKAITALIANOESPAÑOLDUTCH

PLAY

LINE IN-LINE OUT

TAPE PBREC OUT

REC

CONNECTIONS

To an AC outlet

NOTES ON THIS MANUAL

In this manual, the main operation buttons of the front panel are indicated based on DECK B when the operation is common to

both DECKs A and B. Since the locations of the buttons of DECK A and DECK B are the same, you can easily find the desired

button even when operating DECK A. This manual covers two models. In most cases, however, only model KX-W421 is shown

in the example illustrations.

Example: KX-W421

Main operation buttons of DECK A

(U.S.A. model)

Amplifier or receiver

REAR PANEL CONNECTIONS

Make sure that power to both the deck and your amplifier/receiver is turned off

before making any connections.

÷ The White plug on the paired connecting cables corresponds to the Left

channel and the Red plug corresponds to the Right channel. Make sure that

the left and right channel connections are properly made, and that the plugs

are inserted firmly.

÷ The LINE OUT/PLAY jacks on the deck should be connected to the TAPE PB

(Playback/Input) jacks on your amplifier/receiver, and the LINE IN/REC jacks

on the deck should be connected to the REC OUT (Recording/Output) jacks

on your amplifier/receiver.

÷ The LINE OUT terminals on this unit are numbered 3 and the LINE IN jacks

are numbered 4. When connecting this unit to a YAMAHA amplifier or

receiver whose terminals are numbered 1, 2, 3, 4 ... (etc.), connect this

unit's LINE OUT terminals to the input terminals numbered 3 and connect this

unit's LINE IN terminals to the output terminals numbered 4 on the rear panel

of the amplifier or receiver.

÷ Connect the power cord to an AC wall outlet or to an AC outlet on the rear

panel of your amplifier/receiver (if provided).

NATURAL SOUND CASSETTE DECK KX-W421

DOLBY NR

OFF/ B/ C

REC

LEVELBALANCE

PLAY TRIM

PHONES

STANDBY/ON

MODE

O / p / ∏ / RELAY

PLAYBACK

DECK A

Stabilizer

RECORD/PLAYBACK

DECK B

L R MIN MAX

–+

CassetteStabilizerCassette

% %

DIRECTION RESETRESET DIRECTION

! ⁄

!⁄

MUTE/SEARCH

REC/PAUSE

PLAYPLAY

EJECT EJECT

NORMAL HIGH

DUBBING A # B

0 0

Main operation buttons of DECK B

PLAYBACK (Common to DECKs A and B)

Preparation for playback

÷ Turn on the STANDBY/ON switch.

÷ Set your amplifier or receiver to cassette deck function mode.

BASIC OPERATION - To play back a cassette tape

Example: KX-W421

EJECT

DOLBY NR

OFF/ B/ C

Refer to the following

description.

MODE

“/[/”/

RELAY

Refer to the following

description.

DIRECTION

Select the tape running direction for DECK A

or B. Each time this button is pressed, the

tape running direction changes between

forward (#) and reverse (@), and the

corresponding indicator lights on the display.

To stop playback

Press the & button. To remove the cassette tape, press the

EJECT button. The cassette compartment door opens. To

set the unit to standby mode, press the STANDBY/ON

button.

To set the counter reading to “0000”

Press the RESET button. Use the tape counter to aid in

locating a point on a tape (0000 to 9999).

To fast forward or rewind the tape

When the tape running indicator # is lit:

Pressing the ⁄ button fast forwards the tape while

pressing the ! button rewinds the tape.

When the tape running indicator @ is lit:

Pressing the ! button fast forwards the tape while

pressing the ⁄ button rewinds the tape.

Insert the cassette with the exposed tape side facing down. (The side

facing you is called the forward side and the opposite side is called the

reverse side.) To close the compartment, push the section of the

compartment door marked % CLOSE until it locks shut.

PLAY

NATURAL SOUND CASSETTE DECK KX-W421

DOLBY NR

OFF/ B/ C

REC

LEVELBALANCE

PLAY TRIM

PHONES

DIRECTION

STANDBY/ON

MODE

O / p / ∏ / RELAY

! ⁄

PLAY PLAY

EJECT

NORMAL HIGH

DUBBING A # B

!⁄

MUTE/SEARCH REC/PAUSE

EJECT

RESET

RESET DIRECTION

Stabilizer

CLOSECLOSE

PLAYBACK

DECK A

Cassette

RECORD/PLAYBACK

DECK B

StabilizerCassette

–+

MIN MAX

STANDBY/ON

PHONES

RESET

⁄

ENGLISHFRANÇAISDEUTSCHSVENSKAITALIANOESPAÑOLDUTCH

DOLBY NR selector setting (in step 2)

Be sure to set the DOLBY NR selector according to the

system used for recording.

OFF: For a tape recorded with DOLBY NR OFF.

B: For a tape recorded with DOLBY B NR.

C: For a tape recorded with DOLBY C NR.

REVERSE MODE selector setting (in step 3)

The auto reverse function allows the tape running direction

be reversed automatically. Select an auto reverse mode

(

, , or

RELAY

) or manual reverse mode

(

: When playback or fast forwarding (or rewinding) of

one side of a tape is finished, the deck stops at the

end of the tape.

:Both sides of the tape are played back. After

playing, the deck stops at the end of the tape.

(When the tape running direction is set to ¤, only

the reverse side is played.)

: Both sides of the tape are repeatedly played back

(up to 8 times).

RELAY

: Cassette tapes loaded in DECKs A and B

are played back sequentially. (See “RELAY

PLAYBACK” on page 9.)

Display during playback

Tape counter

Peak level meters

Indicate the peaks of the signal levels during recording and playback over a –30 dB to +6 dB range. There are separate meters for each left

and right channel. These level meters have a peak hold function which holds the peak level for about 1.5 seconds.

¤

30 dB

—

NORM

‹

20 15 10 8 6 4 2 0 2 4 6

¤

‹

RELAY

DUB HIGH RECB C

KX-W421/

KX-W321

The A or B indicator shown in

the display represents the

last deck operated.

Note

Never press the EJECT button when the tape is in motion.

To adjust the volume level

Use the volume control of the amplifier or receiver.

To use headphones

Insert the headphones plug into the PHONES jack. Since

the sound is also heard from the speakers, operate the

amplifier to cut off the sound from the speakers for private

listening.

Tape running direction

indicator (DECK A)

Tape running direction

indicator (DECK B)

Notes

÷ The blank interval between selections must be at least 4 seconds long.

÷ Selection search may not operate properly with tapes recorded at a low recording level or which have excessive noise.

Example: KX-W421

SELECTION SEARCH - To play back a desired selection by searching for the beginning of the selection

When the @ tape running indicator is lit:

To search for the next selection

When the # tape running indicator is lit:

When the @ tape running indicator is lit:

To search for the beginning of the current selection

When the # tape running indicator is lit:

To search for the selection located before the current selection

÷ Operate the following buttons when the beginning of the current selection is being played.

When the # tape running indicator is lit:

When the @ tape running indicator is lit:

Press

simultaneously.

⁄

MUTE/SEARCH

Press

simultaneously.

Press

simultaneously.

⁄

MUTE/SEARCH

Press

simultaneously.

MUTE/SEARCH

Press

simultaneously.

MUTE/SEARCH

⁄

Press

simultaneously.

NATURAL SOUND CASSETTE DECK KX-W421

DOLBY NR

OFF/ B/ C

REC

LEVELBALANCE

PLAY TRIM

PHONES

STANDBY/ON

MODE

O / p / ∏ / RELAY

PLAYBACK

DECK A

Stabilizer

RECORD/PLAYBACK

DECK B

L R MIN MAX

–+

CassetteStabilizerCassette

DIRECTION RESETRESET DIRECTION

! ⁄

!⁄

MUTE/SEARCH

REC/PAUSE

EJECT EJECT

NORMAL HIGH

DUBBING A # B

RESET

!⁄

MUTE/SEARCH

% %

PLAYPLAY

ENGLISHFRANÇAISDEUTSCHSVENSKAITALIANOESPAÑOLDUTCH

Example: KX-W421

RELAY PLAYBACK - To play DECK A and DECK B sequentially

Load the cassette tapes into DECKs A and B, start playback from DECK A.

The playback patterns differ according to the setting of the MODE button. Refer to the following.

When the MODE button is set to

RELAY

DECK A (forward side \ reverse side) \ DECK B (forward side \ reverse side)

When the MODE button is set to

DECK A (forward side \ reverse side) DECK B (forward side \ reverse side)

When the MODE button is set to

DECK A (forward side \ reverse side) DECK B ( forward side \ reverse side)

÷ When the tape running direction is set to ™, only the reverse side is played.

When the MODE button is set to

DECK A (forward side or reverse side) DECK B (forward side or reverse side)

Display

Up to 8 times

RELAY

100

10 dB

10kHz

When the level of high frequencies is either over emphasized or absent while playing a tape recorded on another cassette deck,

adjust the high frequency response with the PLAY TRIM control.

When high frequencies are too loud,

attenuate the high frequencies.

PLAY TRIM

When high frequencies are too soft, boost

the high frequencies.

1 High frequency sound is too loud.

2 Flat

3 High-frequency sound is too soft.

PLAY TRIM CONTROL ADJUSTMENT ( KX-W421 only)

NATURAL SOUND CASSETTE DECK KX-W421

DOLBY NR

OFF/ B/ C

REC

LEVELBALANCE

PLAY TRIM

PHONES

STANDBY/ON

MODE

O / p / ∏ / RELAY

PLAYBACK

DECK A

Stabilizer

RECORD/PLAYBACK

DECK B

L R MIN MAX

–+

CassetteStabilizerCassette

DIRECTION RESETRESET DIRECTION

! ⁄

!⁄

MUTE/SEARCH

REC/PAUSE

EJECT EJECT

NORMAL HIGH

DUBBING A # B

PLAY TRIMMODE

% %

PLAYPLAY

PLAY TRIM

RECORDING

EJECT

Recording

starts.

Play the program source to be

recorded and adjust the

recording level and balance.

(KX-W321 does not have a

REC BALANCE control.)

LEVELBALANCE

REC

Preparation for recording

÷ Turn on the STANDBY/ON switch.

÷ Set your amplifier or receiver to cassette deck function mode.

BASIC OPERATION - To record a program source

Example: KX-W421

LRMIN MAX

DOLBY NR

OFF/ B/ C

Insert the cassette into DECK B with the

exposed tape side facing down. (The

side facing you is called the forward side

and the opposite side is called the

reverse side.)

To close the compartment, push the

section of the compartment door marked

% CLOSE until it locks shut.

Select the tape running direction.

(Press the DIRECTION button for DECK B.) Each

time the button is pressed, the tape running direction

changes between forward (#) and reverse (@), and

the indicator lights on the display.

The REC indicator

lights on the display.

The deck enters the

Rec/Pause mode.

REC/PAUSE

DIRECTION

MODE

“/[/”/

RELAY

Refer to the following

description.

Refer to the following

description.

PLAY

NATURAL SOUND CASSETTE DECK KX-W421

DOLBY NR

OFF/ B/ C

REC

LEVELBALANCE

PLAY TRIM

PHONES

DIRECTION

STANDBY/ON

MODE

O / p / ∏ / RELAY

! ⁄

EJECT

NORMAL HIGH

DUBBING A # B

!⁄

MUTE/SEARCH REC/PAUSE

EJECT

RESET

RESET DIRECTION

Stabilizer

PLAYBACK

DECK A

Cassette

RECORD/PLAYBACK

DECK B

StabilizerCassette

–+

MIN MAX

STANDBY/ON

PHONES

RESET

⁄

MUTE/SEARCH

PLAY PLAY

CLOSECLOSE

ENGLISHFRANÇAISDEUTSCHSVENSKAITALIANOESPAÑOLDUTCH

¤

30 dB

—

‹

20 15 10 8 6 4 2 0 2 4 6

¤

‹

REC

RELAY

B C

DOLBY NR selector setting (in step 2)

Set the DOLBY NR selector according to your purpose.

OFF: No noise reduction.

B: For recording the sources with Dolby B NR.

C: For recording the sources with Dolby C NR.

÷ Dolby noise reduction is an extremely effective method of

reducing undesirable background hiss on tapes. This unit

incorporates both Dolby B NR and the newer Dolby C NR

system. Dolby C NR is approximately twice as effective

as the earlier Dolby B NR.

REVERSE MODE selector setting (in step 3)

The auto reverse function allows the tape running direction

to be reversed automatically. Select the auto reverse mode

(

) or manual reverse mode ( ).

: When recording on one side of a tape is finished, the

deck stops at the end of the tape.

:Both sides of a tape are recorded. After recording,

the deck stops at the end of the tape.

÷ When the tape running direction is set to ™, only

the reverse side is recorded.

÷ If you select

RELAY

, the reverse mode

automatically switches to

in step 5.

Display during recording

Peak level meters

Indicate the peaks of the signal levels during recording and playback over a –30 dB to +6 dB range. There are separate meters

for each left and right channel. These level meters have a peak hold function which holds the peak level for about 1.5 seconds.

Tape counter

Use the tape counter to aid in locating a point on a tape (0000 to 9999).

To set the counter reading to “0000”, press the RESET button.

The A or B indicator shown in

the display represents the

last deck operated.

Setting the recording level (in step 6)

Play the loudest passage of the source to be recorded and

watch the meter readings.

Adjust the REC LEVEL control so that the highest peak

reaches +4 of the optimum recording level. Normally, it is

best to adjust the REC BALANCE control (KX-W421 only)

such that the left and right meter readings are even.

KX-W421/

KX-W321

To stop recording:

Press the & button.

To stop recording temporarily:

Press the REC/PAUSE button. To resume recording, press

the PLAY button.

REC indicator

DOLBY B/ C indicator

MODE indicator

Tape running direction indicator

Example: KX-W421

REC MUTE OPERATION - Inserting a blank space during recording

REC RETURN OPERATION - To return to the point at which the recording started

A 4-second blank interval is automatically recorded on the

tape and then the deck enters Rec/Pause mode.

If a blank interval longer than 4 seconds is desired, keep

pressing for as long as you want. When the MUTE/

SEARCH button is released, the deck enters Rec/Pause

mode after making a 4-second blank interval.

To resume recording, press the PLAY button.

÷ If a blank interval shorter than 4 seconds is desired, press

the PLAY button at the desired point during Rec mute

mode. Recording will be resumed from that point.

During recording:

During Rec mute operation, the REC indicator blinks.

During recording:

When the # indicator

is lit:

⁄

When the @ indicator

is lit:

÷ If you press the PLAY button during recording, Rec Return

automatically rewinds the tape to the point where the

PLAY button was pressed.*

If you reset the tape counter to “0000” during recording,

Rec Return automatically rewinds the tape to the “0000”

point.

Rec Return functions according to the most recent

operation. For example, if you reset the tape counter to

“0000” and then press the PLAY button later, Rec Return

rewinds to the point where the PLAY button was pressed.

* The PLAY button cannot be used to mark a return point

while dubbing.

MUTE/SEARCH

DOLBY HX PRO DYNAMIC BIAS SERVO SYSTEM

(KX-W421 only)

This unit incorporates the Dolby HX Pro system which

automatically controls the effective bias to reduce

distortion and noise, improving high frequency

response during recording. Tapes recorded with this

system retain the same high quality even when played

back on any other cassette deck.

Synchronized recording function

When operating this unit in combination with the

YAMAHA CD Player which has SYNCHRO button on its

remote control transmitter, CD Synchronized recording

function can be utilized. This function is operated with

the remote control transmitter of the CD Player.

(Regarding the operation, refer to the manual of the CD

Player.)

NATURAL SOUND CASSETTE DECK KX-W421

DOLBY NR

OFF/ B/ C

REC

LEVELBALANCE

PLAY TRIM

PHONES

STANDBY/ON

MODE

O / p / ∏ / RELAY

PLAYBACK

DECK A

Stabilizer

RECORD/PLAYBACK

DECK B

L R MIN MAX

–+

CassetteStabilizerCassette

DIRECTION RESETRESET DIRECTION

! ⁄

!⁄

MUTE/SEARCH

REC/PAUSE

EJECT EJECT

NORMAL HIGH

DUBBING A # B

!⁄

MUTE/SEARCH

% %

PLAYPLAY

ENGLISHFRANÇAISDEUTSCHSVENSKAITALIANOESPAÑOLDUTCH

DUBBING (From DECK A to DECK B)

Set the MODE selector to

or position.

If you select or

RELAY

, the reverse

mode automatically switches to

Set the

DIRECTION

buttons for DECKs

A and B.

Set the dubbing speed to either NORMAL

(normal speed) or HIGH (twice the normal

speed) with the DUBBING buttons*.

Dubbing starts automatically.

DUBBING A # B

NORMAL HIGH

The corresponding NORM

or HIGH indicator lights on

the display.

* Higher quality sound will be obtained with the

NORMAL setting.

Note

During dubbing, Dolby NR is automatically set to off and the

recorded tape can be dubbed as is. (When the tape to be

dubbed is recorded with Dolby NR, this effect is also

dubbed.)

PLAY TRIM control adjustment (KX-W421 only)

For normal use, set the PLAY TRIM control to the center

position.

When the high frequencies sound is too noticeable or too

weak while monitoring the sound of DECK B, compensate

the high frequency response with the PLAY TRIM control

before dubbing. The compensated sound can be dubbed

onto DECK B.

As the compensation result depends on the quality of the

tape loaded in DECK A, the monitored sound cannot be

recorded as it is.

Refer to “PLAY TRIM CONTROL ADJUSTMENT” on page

To stop dubbing

Press the & button. (If you press the & button on DECK B,

both decks stop simultaneously and the dubbing mode is

cancelled. If you press the & button on DECK A, DECK A

stops immediately and then DECK B stops after recording a

4-second blank section.)

When the tape in DECK B reaches its end, DECK B stops

and then DECK A stops.

When the tape in DECK A reaches its end, DECK A stops

and DECK B stops after providing a blank section of about 4

seconds.

Available operations while dubbing

The Rec Return function can be carried out on DECK B.

Refer to “REC RETURN OPERATION” on the previous

page.

You can make dubbing from DECK A to DECK B. Open the cassette compartments by pressing the EJECT buttons and load a

blank cassette tape in DECK B and the original cassette tape in DECK A.

Example: KX-W421

Display during dubbing

MODE

“/[/”/

RELAY

DIRECTION

NORM or HIGH

indicator lights during

dubbing.

Lights during dubbing.

NATURAL SOUND CASSETTE DECK KX-W421

DOLBY NR

OFF/ B/ C

REC

LEVELBALANCE

PLAY TRIM

PHONES

STANDBY/ON

MODE

O / p / ∏ / RELAY

PLAYBACK

DECK A

Stabilizer

RECORD/PLAYBACK

DECK B

L R MIN MAX

–+

CassetteStabilizerCassette

DIRECTION RESETRESET DIRECTION

! ⁄

!⁄

MUTE/SEARCH

REC/PAUSE

EJECT EJECT

NORMAL HIGH

DUBBING A # B

30 dB

–

NORM

‹

20 15 10 8 6 4 2 0 2 4 6

‹

RELAY

DUB HIGH RECB C

% %

PLAYPLAY

PROTECTING YOUR RECORDINGS

All cassette tapes are provided with erasure protection holes

to prevent accidental erasure of recorded contents. There is

a small tab covering the hole on each side of the cassette,

and it should be broken off after recording the tape. Without

this tab covering the hole, it is impossible to record onto that

tape. Thus, you can safely protect a recording for as long as

you wish without fear of accidental erasure. Should you wish

to use a cassette tape protected in this way for recording,

simply covering the hole with adhesive tape will permit

erasure and re-recording.

÷ When using Chrome (Type II/HIGH <CrO

2>) or Metal

(Type IV/METAL) tapes, make sure you do not cover the

hole intended for the Auto Tape Selector operation.

TAKING UP SLACK IN THE TAPE

As a precaution against tape entanglement and damage,

remove any slack in the tape before inserting cassettes into

the deck. This is accomplished by inserting a pencil, pen or

similar object into one of the spools and gently winding it

until all the slack is removed. You do not have to wind it too

tightly.

Be careful not to touch the tape part itself. It is very delicate

and touching it may damage the tape and its recorded

contents.

STORING CASSETTES

After putting a cassette tape back into its case, store it in a

location away from exposure to direct sunlight, humidity,

high temperatures, and magnetic fields (away from television

sets, speakers, etc.). High temperatures and humidity will

damage the tape itself, while exposure to magnetic fields

may cause a loss of recorded material. Avoid touching the

tape surface with your fingers, since dirt or finger oil will

contaminate the deck’s heads.

CASSETTE TAPES

There are many different types of cassette tapes available.

However, they all conform to standard specifications so any

brand may be used with the deck.

÷ Classification of Cassette Tapes by Formulation:

Cassette tapes are available in four basic types depending

on their formulation, or type of magnetic material and

manufacturing process. These four types are commonly

known as Normal (Type I/NORM), Chrome (Type II/HIGH

<CrO

2>), Ferrichrome (Type III/FeCr), and Metal (Type IV/

METAL), and they each require specific tape deck

adjustments for optimum performance.

* YAMAHA does not recommend the use of 120 minute

length cassettes since the extreme thinness of the tape

makes them susceptible to mechanical and recording

problems.

AUTO TAPE SELECTOR DETECTION SLOTS

The deck has a built-in Auto Tape Selector which

automatically adjusts for the proper bias, level and

equalization according to the tape formulation — all you

have to do is to load a cassette and the Auto Tape Selector

does the rest.

The Auto Tape Selector determines which type of tape is

loaded by sensing detector slots in the top of the tape shell.

Each tape formulation has its own characteristic hole

markings standardized by the tape industry.

÷ Early model Metal (Type IV/Metal) tape formulation

cassette shells do not have the slots for Auto Tape

Selector operation. As a result, early model Metal type

tapes recorded on another deck will be played back with

the deck at the Chrome (Type II/HIGH <CrO

2>) settings.

YAMAHA does not recommend using this kind of tape.

÷ The deck does not have the required setting for

Ferrichrome (Type III/FeCr) tape, since this tape

formulation is not widely used. Should you use a

Ferrichrome tape, it will be recorded and played back at

the Normal (Type I/NORM) settings, which will result in an

unnatural high frequency emphasis. This effect may be

compensated for somewhat by adjusting the PLAY TRIM

control and/or the tone controls of your amplifier/receiver

during playback.

Detector slotsDetector slots

TYPE II TYPE IV

ENGLISHFRANÇAISDEUTSCHSVENSKAITALIANOESPAÑOLDUTCH

With the optional remote control transmitter RKX1, you can

operate this unit at your listening position. For details, refer

to the instruction manual supplied with the remote control

transmitter.

REMOTE CONTROL OPERATION RANGE

MAINTENANCE

CLEANING OF THE TAPE PATH

Continued high quality performance of your deck is

dependent upon periodic cleaning of the heads, capstan,

pinch roller, and all surfaces over which the tape travels.

Normal use will cause an accumulation of dirt and dust on

the heads, capstans, and pinch rollers. This can lead to

poor sound quality, drop outs (intervals with no sound),

unsteady tape speed, loss of high frequency response, etc.

Thus, clean the heads and all surfaces over which the tape

travels with a commercially available cleaning cassette and

fluid type cleaner.

DEMAGNETIZATION

After 20-30 hours of use, enough residual magnetism will

build up on the heads to cause poor high frequency

reproduction. At this time you should use a commercially

available cassette tape-type head demagnetizer.

÷ When cleaning the tape path or demagnetizing the heads,

be sure to follow carefully the instructions of the

concerning materials such as cleaning fluid or head

demagnetizer.

CapstanCapstan

Pinch rollerPinch roller

Heads

OPTIONAL REMOTE CONTROL TRANSMITTER

Example: KX-W421

DECK B

30°

7 m (23 feet)

Remote sensor

SINGLE DECK

INTRO SCAN

DOUBLE DECK

DUBBING

DECK A/B DIR A DIR B

COUNTER

RESET

PLAY

REC/PAUSE REC MUTE

STOP

RKX1

¤‹

⁄

If your cassette deck fails to operate normally, check the following table. It lists common operating errors and simple measures

which you can take to correct the problem. If it cannot be corrected, or the symptom is not listed, disconnect the deck’s power

cord and contact your authorized YAMAHA dealer or authorized service center for help.

Cause

÷ Power plug is not properly plugged in.

÷ Cassette shell is warped or damaged.

÷ There is an influence of strong external

noise (lightning, excessive static

electricity, etc.) or a misoperation was

performed while using this unit.

÷ No cassette tape loaded.

÷ Protective tabs are broken off.

÷ Head is dirty.

÷ Head is magnetized.

÷ Tape is damaged or of poor quality.

÷ Tape is bad (stretched, deformed, etc.).

÷ Cassette shell is warped.

÷ Recording level is too high.

÷ Faulty connection between deck and

stereo amplifier/receiver.

÷ Head is dirty.

÷ Head is magnetized.

÷ Worn out or poor quality tape.

÷ Connection(s) improperly made.

÷ Affected by external electrical noise.

÷ Dirty capstan, pinch roller, etc., or poor

tape.

÷ Tape is wound unevenly.

÷ Slack tape, or tape spillage wound

around capstan.

÷ REC LEVEL control is set to too low.

÷ Protective tabs are broken off.

÷ Blank section is too short.

÷ Recorded section has low-level portions.

÷ Conversation, etc. has been recorded.

÷ Dolby NR-recorded tape is played back

in OFF position.

Cure

÷ Reinsert plug properly.

÷ Do not play damaged tapes.

÷ Turn the unit off and disconnect the AC

power from the AC outlet. After about

30 seconds have passed, connect the

power and try again.

÷ Load a cassette tape.

÷ Change tape or cover protective hole

with adhesive tape.

÷ Clean head.

÷ Demagnetize head using head

demagnetizer.

÷ Change to a different tape.

÷ Replace with a fresh tape.

÷ A warped cassette shell cannot be

fixed. Replace with another tape and

test.

÷ Check input level with signal level meter

and use lower rec level when recording.

÷ Check and secure connections.

÷ Clean head.

÷ Demagnetize head with head

demagnetizer.

÷ Change to better tape.

÷ Check input and output connections

and reinsert properly.

÷ Move deck away from electrical

appliances (TV, fluorescent light,

electric blanket, etc.).

÷ Clean capstan and pinch roller, or

change to better tape.

÷ Rewind tape.

÷ Insert pencil in hole in cassette shell

and turn to take up slack.

÷ Adjust REC LEVEL control.

÷ Change tape or cover protective hole

with adhesive tape.

÷ Blank sections must be at least 4

seconds long.

÷ No remedy

÷ Play back in appropriate Dolby NR

position.

Fault

Tape doesn’t move in recording or

playback.

If it happens that this unit does not

work normally.

REC/PAUSE button fails to function.

Sounds become faint and sometimes

inaudible.

Recorded sound is distorted.

Tape is playing back, but no sound is

heard.

Excessive noise.

Excessive wow (wavering of the

sound).

Tape stops in the middle of recording

or playback.

Fails to record.

Search does not operate correctly.

High frequencies in the playback

sound are emphasized and unpleasant

to listen to, and noise level (hiss) is

also high.

TROUBLESHOOTING

ENGLISHFRANÇAISDEUTSCHSVENSKAITALIANOESPAÑOLDUTCH

Cause

÷ Normally-recorded tape is played back in

Dolby NR.

÷ Heads are dirty.

÷ Heads are magnetized.

÷ Basic levels are different for different

cassette decks.

÷ The batteries are exhausted.

÷ The remote control transmitter is

operated from an incorrect distance or

angle.

÷ The remote control sensor is lighted

strongly.

Cure

÷ Play back in OFF position.

÷ Clean heads and carry out

demagnetization with head

demagnetizer.

÷ This is not a fault.

÷ Replace batteries.

÷ Operate it from less than 7 meters

(about 23 ft.) and 30°.

÷ Place the unit away from the strong

light.

Fault

Playback sound is muffled and high

frequencies are inaudible.

When playing back tapes recorded on

other decks, meter deflections are

greater (smaller) than when recorded.

The remote control transmitter cannot

be operated.

Type..................................... Auto reverse 4-track, 2-channel

recording and playback stereo double cassette deck

Motors .........................................DC servo motor x 2 (main)

Heads .................... Recording/playback: Hard Permalloy x 1

Erase: Double-gap Ferrite x 1

Playback: Hard Permalloy x 1

Rapid Transport .......................................... 100 sec. (C-60)

Wow and Flutter

WRMS ...................................................................... 0.08%

W.Peak ...................................................................±0.15%

Signal-to-Noise Ratio

(Dolby NR off)...........................................................58 dB

(Dolby B NR on) .......................................................66 dB

(Dolby C NR on) .......................................................74 dB

Frequency Response (–20 dB)

<KX-W421>

Type I/Normal.............................. 20 ~ 17,000 Hz ±3 dB

Type II/High (CrO

2) .................... 20 ~ 18,000 Hz ±3 dB

Type IV/Metal .............................. 20 ~ 20,000 Hz ±3 dB

<KX-W321>

Type I/Normal.............................. 20 ~ 16,000 Hz ±3 dB

Type II/High (CrO

2) .................... 20 ~ 17,000 Hz ±3 dB

Type IV/Metal .............................. 20 ~ 19,000 Hz ±3 dB

Harmonic Distortion

KX-W421 .................................................... less than 0.8%

KX-W321 .................................................... less than 1.0%

Input Sensitivity/Impedance

Line ...................................................... 100 mV/43 k-ohms

Output Level

Line .....................................................570 mV/1.4 k-ohms

Phones..................................................... 0.25 mV/8 ohms

Channel Separation (1 kHz)...................... more than 40 dB

Crosstalk (125 Hz) ..................................... more than 55 dB

SPECIFICATIONS

GENERAL

Power Supply

U.S.A. and Canada model ........................... 120 V, 60 Hz

Europe and U.K. model ............................... 230 V, 50 Hz

Australia model............................................ 240 V, 50 Hz

General model.................... 110/120/220/240 V, 50/60 Hz

Power Consumption

KX-W421 ............................................14 W/7 W (Standby)

KX-W321

U.S.A. and Canada model.............11 W/7 W (Standby)

Other models .................................12 W/7 W (Standby)

Dimensions (W x H x D)...................... 435 x 146 x 279 mm

(17-1/8" x 5-3/4" x 11")

Weight ........................................................... 5.0 kg (11 lbs.)

Accessory

Audio cord................................................................ 1 pair

* Specifications subject to change without notice.

Problème

Le son de lecture est étouffé et les

hautes fréquences sont inaudibles.

Lors de la lecture de bandes

enregistrées sur d’autres platines, les

déflexions du compteur sont plus

grandes (plus petites) qu’à

l’enregistrement.

La télécommande ne fonctionne pas.

Remède

÷ Lire en position OFF.

÷ Nettoyer les têtes et effectuer la

démagnétisation avec un

démagnétiseur de tête.

÷ Ceci n’est pas un défaut.

÷ Remplacer la pile.

÷ La faire fonctionner à moins de 7

mètres et sur 30°.

÷ Placer l’appareil à l’abri de lumières

fortes.

Cause

÷ Une bande enregistrée normalement est

lue avec Dolby NR.

÷ Les têtes sont sales.

÷ Les têtes sont magnétisées.

÷ Les niveaux de base sont différents pour

diverses platines.

÷ La pile est déchargée.

÷ La télécommande est actionnée d’une

distance ou sous un angle incorrects.

÷ Le détecteur de la télécommande est

fortement éclairé.

Configuration des pistes ............. Platine à cassette double

stéréo avec inversion automatique pour l’enregistrement et

la lecture, 4 pistes, 2 canaux

Moteur ..............Moteur asservi CC x 2 (moteurs principaux)

Têtes...................Enregistrement/Lecture: Permalloy dur x 1

Effacement: Ferrite à double entrefer x 1

Lecture: Permalloy dur x 1

Transport rapide................................. 100 secondes (C-60)

Pleurage et scintillement

Eff., pondéré........................................................... 0,08%

Crête, pondéré ..................................................... ±0,15%

Rapport signal/bruit

(Dolby NR à l’arrêt)...............................................58 dB

(Dolby B NR en marche) ......................................66 dB

(Dolby C NR en marche) ......................................74 dB

Réponse en fréquence (–20dB)

<KX-W421>

Type I/normale ............................ 20 ~ 17.000 Hz ±3 dB

Type II/élevée (CrO

2) .................. 20 ~ 18.000 Hz ±3 dB

Type IV/métal .............................. 20 ~ 20.000 Hz ±3 dB

<KX-W321>

Type I/normale ............................ 20 ~ 16.000 Hz ±3 dB

Type II/élevée (CrO

2) .................. 20 ~ 17.000 Hz ±3 dB

Type IV/métal .............................. 20 ~ 19.000 Hz ±3 dB

Distorsion harmonique

KX-W421 ................................................... Moins de 0,8%

KX-W321 ................................................... Moins de 1,0%

Sensibilité d’entrée/impédance

Ligne ....................................................100 mV/43 k-ohms

Niveau de sortie

Ligne ...................................................570 mV/1,4 k-ohms

Casque.....................................................0,25 mV/8 ohms

Séparation des canaux (1 kHz) ...............inférieure à 40 dB

Diaphonie (125 Hz) ...................................inférieure à 55 dB

GENERALES

Alimentation

Modèle pour les Etats-Unis et le Canada

................................................................... 120 V, 60 Hz

Modèle pour l’Europe et le Royaume-Uni

................................................................... 230 V, 50 Hz

Modèle pour l’Australie ............................... 240 V, 50 Hz

Modèle général............................................ 110/120/220/

240 V, 50/60 Hz

Consommation

KX-W421 ................................................ 14 W/7 W (Veille)

KX-W321

Modèle pour les Etats-Unis et le Canada

............................................................ 11 W/7 W (Veille)

Autres modèles ................................. 12 W/7 W (Veille)

Dimensions (L x H x P) ....................... 435 x 146 x 279 mm

Poids ........................................................................... 5,0 kg

Câbles audio ......................................................... 1 paire

* Les caractéristiques techniques sont sujettes à des

changements sans préavis.

CARACTERISTIQUES TECHNIQUES

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, 25462 RELLINGEN, BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VASTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia

VZ 79000-1

Yamaha KX-W321 Manual de usuario

Marca: Yamaha

Modelo: KX-W321

Categoría: Reproductores de casete

Tipo: Manual de usuario

Este manual también es adecuado para

KX-W421

Descargar PDF

informe

En otros idiomas

français: Yamaha KX-W321 Manuel utilisateur
italiano: Yamaha KX-W321 Manuale utente
English: Yamaha KX-W321 User manual
Deutsch: Yamaha KX-W321 Benutzerhandbuch
русский: Yamaha KX-W321 Руководство пользователя
Nederlands: Yamaha KX-W321 Handleiding
português: Yamaha KX-W321 Manual do usuário
dansk: Yamaha KX-W321 Brugermanual
polski: Yamaha KX-W321 Instrukcja obsługi
čeština: Yamaha KX-W321 Uživatelský manuál
svenska: Yamaha KX-W321 Användarmanual
Türkçe: Yamaha KX-W321 Kullanım kılavuzu
suomi: Yamaha KX-W321 Ohjekirja
română: Yamaha KX-W321 Manual de utilizare

Yamaha KX-W321 Manual de usuario

Este manual también es adecuado para

Yamaha KX-W321 Manual de usuario

En otros idiomas

Documentos relacionados

Otros documentos