Grill-Max 75CFV Instrucciones de operación
- Categoría
- Barbacoas
- Tipo
- Instrucciones de operación
®
®
®
ROLLER
GRILLS
MODEL
20C, 30C, 45C, 50C & 75C
Infi nite and Electronic Controls
Installation and
Operation
Instructions
2M-Z9106 Rev. C 5/08/06
30SCBB
2
2
These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
NOTICE
Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.
Star reserves the right to change specifi cations and product design without
notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.
Due to periodic changes in designs, methods, procedures, policies and
regulations, the specifi cations contained in this sheet are subject to change
without notice. While Star Manufacturing exercises good faith efforts to provide
information that is accurate, we are not responsible for errors or omissions
in information provided or conclusions reached as a result of using the
specifi cations. By using the information provided, the user assumes all risks in
connection with such use.
MAINTENANCE AND REPAIRS
Contact your local dealer for service or required maintenance. Please record the model number, serial
number, voltage and purchase date in the area below and have it ready when you call to ensure a faster
service.
SAFETY SYMBOL
Model No.
Serial No.
Voltage
Purchase Date
TABLE OF CONTENTS
PAGE NUMBER
CONNECTION LOAD 3
GENERAL OPERATING INSTRUCTIONS 4
CLEANING 4
ELECTRONICALLY CONTROLLED:
START-UP, HEATING & PROGRAMING 5
WARRANTY 6
WIRING DIAGRAM 7-10
EXPLODED VIEW 11, 12
PARTS LIST
20 MODEL SERIES 13
30 MODEL SERIES 14, 15
45 MODEL SERIES 16, 17
50 MODEL SERIES 18, 19
75 MODEL SERIES 20, 21
CAUTION
This equipment is designed and sold for commercial use only by personnel trained and
experienced in its operation and is not sold for consumer use in and around the home nor for
use directly by the general public in food service locations. For equipment to be used by the
general public, please contact the factory
.
INSTALLATION
This grill is equipped for the voltage shown on the nameplate. It will operate on alternating
current only, however, the specifi ed voltage must be applied.
CAUTION
DO NOT CONNECT TO DIRECT CURRENT (DC).
CONNECTION LOAD:
INFINITE CONTROL
MODEL SERIES WATTAGE
20C, 20SC 930
30C, 30SC, 30CF, 30SCF, 30CBB, 30CBBC,
30SCBB, 30CDV 1150
45C, 45SC, 45CBB, 45SCBB, 45CDV 1650
50C, 50SC, 50CF, 50SCF, 50CBB, 50CBBC,
50SCBB, 50CDV 1535
75C, 75SC, 75CBB, 75SCBB, 75FF,
75SCF 208/240V 1810/2400
75C, 75SC, 75CBB, 75SCBB,
75CDV 230V 2210
75C, 75CF, 75SC, 75SCF, 75CBB,
75SCBB, 75CDV 120V 1700
75CFV 120V 2880
ELECTRONIC CONTROL
MODEL SERIES WATTAGE
20SCE 930
30CE, 30SCE, 30SCEX, 30CBBE
30SCBBE 1150
45SCE, 45SCRE 1650
50CE, 50SCE, 50SCEX 50CBBE, 50SCBBE,
50CBBES 1535
75CE, 75SCE, 75CBBE, 75CBBES,
75SCBBE, 75SCRE 208/240V,
75SCFE 1810/2400
75CE, 75SCE, 75CBBE,
75SCBBE, 75SCRE 120V 1730
INSTALLATION (CONTINUED)
The grill should be connected to a wall type receptacle, a direct line or individual branch circuit.
An individual branch circuit is preferred. If connected to an overloaded circuit the grill will not
operate properly. The unit should be level when installed. Models equipped with bun boxes
must be level to utilize the self-closing feature of the bun drawer. Adjustable 4-inch legs are
standard on the 75 series and available for all other models.
GENERAL OPERATING PROCEDURES
The main switch located on the control panel controls all the power to the unit. With the
main switch on, the rollers will turn, but no heat will be supplied unless the heat controls
are turned on. For fl exibility the heating section of the grill is divided into two individually
controlled heat sections. The right control regulates the heat to the rear section and the left
control regulates the heat to the front section. The switch is lighted to indicate when the unit
is turned on. On Infi nite control grills a signal light is provided above each heat control and
indicates when the heated section is on. An additional light is provided on the end housing
of the unit. This light indicates the position of the main power switch when either the
optional bun drawer front or merchandising door obstructs the control panel view. Bun
box equipped models require the removal of the bun drawer to remove the bun pan and
to remove the drip tray when access to the rear of the unit is obstructed. To remove the
bun drawer, grab the drawer by both sides and pull it out all the way. Lift the front to
unhook the drawer slide from rear drawer roller. Pull the drawer the remainder of the way out.
Use caution not to drop the drawer when reaching the end of the drawer slide travel. To reinsert
the drawer, fi rst hook the drawer slide over the front roller then the back roller. Do not operate
the grill without the drip tray in place.
CAUTION
USE ONLY PLASTIC OR COATED UTENSILS FOR HANDLING THE FOOD PRODUCT.
METAL COULD SCRATCH THE ROLLER COATING AND AFFECT THE CLEAN
ABILITY OF THE ROLLERS.
CAUTION
DO NOT USE STEEL WOOL OR ABRASIVE CLEANERS ON THE ROLLERS.
SCRAPES WILL VOID THE WARRANTY. USE CAUTION WHEN CLEANING A HOT
GRILL TO PREVENT BURNS OR BODILY INJURY.
CLEANING
Before cooking for the fi rst time, wash the rollers with mild soap and water using a soft cloth.
Do not use metal utensils when cooking. Scratches and scrapes will hamper the ability to
easily clean the rollers. Never use steel wool or abrasive cleaners on the rollers. This will
damage the fi nish and the roller bearings. The rollers clean most easily when hot. Use caution
when cleaning to prevent burns and bodily injury. Clean the rollers with a clean wet cloth.
Wipe from the ends to the center to prevent forcing debris into the roller seals. Do not allow
the food product to build up and bake onto the roller surface. The exterior of the unit should
be cleaned using a mild detergent or non-abrasive cleaner. Clean the entire unit daily to
insure long life and satisfactory performance as well as to maintain an attractive appearance.
Do not clean with water jet equipment.
3
START-UP
When initially turning on power to the electronic
controlled grill, it will be in the HOLD mode. The
displays will fl ash until the setpoint temperature
is reached. The grill will beep once when it is
up to temperature. Infi nite controlled grills have
no notifi cation when operating temperature is
reached.
HEATING
The size, content, and shape of the product and the
installation of any sanitary food shields or sneeze
guards will determine the proper heat setting. The
National Sanitation Foundation requires that all
perishable foods be kept at 140°F or above during
serving periods.
The product should be kept refrigerated until
ready to use. Heating times vary depending on
the starting temperature and the qualities of the
product. For best results, use a hot dog made
for grilling.
Before cooking for the fi rst time, wash the rollers
with mild soap and water using a soft cloth. When
the electronic controled grills are initially turned
on, the displays will fl ash the HOLD temperature
until the grill reaches that setpoint.
With the grill preheated to the hold temperature,
load with the desired product and press the HEAT
button. The grill will then go into the heat mode and
the displays will fl ash until the HEAT temperature
is reached. After the heating cycle, the grill will
beep four times and the food product will be at
the serving temperature.
NOTE: Based on the product being heated, some
experimentation is required to fi nd the optimal
HEAT temperature and HEAT time to bring the
product up to temperature in an acceptable amount
of time.
PROGRAMMING
The electronic controls provide programmable
HEAT and HOLD settings for a variety of food
products and installation conditions.
To program the electronic roller grill:
1. With the grill on, push and hold the
and on
the side you wish to program together for three
seconds until the alarm beeps once and the display
blanks.
2. To set the heat temperature and/or heat time, push
the heat button. The last saved heat time will be
displayed and the HEAT LED will fl ash and HEAT
TIME indicator will be ON. Use the
and
buttons to adjust to the desired time, then press
the HEAT button again. The HEAT TIME LED
indicator will turn off and the HEAT TEMP LED
indicator will now be lit. When programming the
HEAT temperature is complete, push the HEAT
button one more time to exit the programming
mode.
3. To set the hold temperature, repeat step 1 above
then push the HOLD button. The last saved hold
temperature will be displayed and HOLD LED will
be ON. Use the
and buttons to adjust to
the desired temperature, then press the HOLD
button again to exit programming mode.
4. To turn the heat off to the front or rear section, press
and hold the
for that section for 3 seconds.
"OFF" will be displayed. To turn the section back
on, press the HEAT or HOLD button.
™
™
PAT. # 6,782,802 PAT. # 6,707,015
MADE IN
U.S.A.
PAT. # 6,393,971
)4+..Ä/#:241
Seal-Max
DURATEC
™
PAT. # 6,782,802 PAT. # 6,707,015
Electronic Control Board
5
OPERATING PROCEDURES FOR ELECTRONIC GRILLS
INTERNATIONAL ONE (1) YEAR EQUIPMENT WARRANTY
All workmanship and materials in “STAR” products are warranted for a period of one year from the date shipped from the factory or
one year from the date shown on the proof of purchase of the end-user when purchased through an authorized “STAR” dealer/dis-
tributor in a commercial foodservice location.
“STAR’s” obligation under this warranty is limited to the replacement of the defective part(s) only without charge. This warranty is
void if damage occurs from improper installation, misuse or abuse, disassembly or tampering of unit for any purpose other than repair
by a qualifi ed service agent, wrong voltage, incorrect or fl uctuating voltage conditions, wrong gas, improper gas or gas conditions,
operated contrary to the installation and operating instructions, operated in an application for which the unit is not suited, or if the unit
is not maintained and/or cleaned in a suitable manner.
Any expense in connection with installation, or any cost of making adjustments on a unit to conform to electric or gas service at the
point of installation, are not covered by this warranty.
* The warranty period for the JetStar series six (6) ounce popcorn machines is two (2) years.
* The warranty period for the Chrome-Max Griddles is fi ve (5) years on the griddle surface. See detailed warranty provided with unit.
* The warranty period for Tefl on/Dura-Tec coatings is one year under normal use and reasonable care. This warranty does not
apply if damage occurs to Tefl on/Dura-Tec coatings from improper cleaning, maintenance, use of metallic utensils, or abrasive
cleaners. This warranty does not apply to the “non-stick” properties of such materials.
* This warranty is not valid on Conveyor Ovens
unless a “start-up/check-out has been performed by a Factory Authorized Technician.
In order to make a claim under this warranty; a warranty report must be fi led with Star Manufacturing International Inc. in St. Louis,
Missouri, U.S.A. by the dealer/distibutor through which product was purchased. All details, including serial number and model num-
ber of the defective unit, must be included. Failure to fi le a claim within a 120 Day time period may result in the claim being refused.
“STAR” may forego the necessity of returning the part for inspection dependent upon the expense involved. However, “STAR”
requires defective parts to be held in the claimant’s possession for a period of ninety (90) days for possible inspection by a “STAR”
representative or designated inspector .
The foregoing warranty is lieu of any and all other warranties, expressed or implied, and constitutes the entire warranty.
PARTS WARRANTY
Parts that are sold for out-of-warranty repair are warranted for a period of ninety days. The part only is warranted; no labor.
SERVICES NOT COVERED BY WARRANTY
1. Labor
2. Mileage and/or travel time
3. Installation and/or adjustment of equipment
4. Operation contrary to the installation and operating instructions
5. Cleaning of equipment
6. Seasoning of griddle plates
7. Voltage conversions/adjustments
8. Gas conversions
9. Pilot light conversion/adjustments
10. Thermostat calibration/adjustments
11. Resetting of circuit breakers or safety controls
12. Replacement of bulbs/lamps
13. Replacement of fuses
14. Damages due to improper installation
15. Damages from abuse or misuse
16. Damage created by acts of God, Acts of War, or Civil Disturbance
08-05 rms
R
MATERIAL
DR.
DATE
FINISH
MODEL NO.
TITLE
PART NO.
TOLERANCES UNLESS OTHERWISE NOTED
FRACTIONS ± 1/64 DECIMALS ± .005
REVISIONS
~
~
RG SERIES
SK1663
WIRE DIAGRAM
BN
6/16/00
CK.
LTR DATE DESCRIPTION OF CHANGE DR
THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.
NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.
STAR MANUFACTURING INTERNATIONAL INC.
#10 SUNNEN DRIVE, ST. LOUIS, MO. 63143, USA
B
6/16/00
REDRAWN FOR CLARITY
REDRAWN TO NEW STAR TITLE
BN
FRONT
REAR
MODEL 30D & 30SD 230 VOLT
(AS VIEWED FROM REAR OF PANEL)
B
B
PILOT
H1
7
7
11
9
9
10
H2
L1
L2
3
6
6
1
2
PILOT
H1
7
7
L1
H2
L2
4
1
2
FRONT
(AS VIEWED FROM REAR OF PANEL)
MODEL 20 & 20S 230 VOLT
REAR
B
B
PILOT
H1
7
7
9
H2
L1
L2
3
6
6
1
5
10
PILOT
H1
7
7
L1
H2
L2
4
1
(AS VIEWED FROM REAR OF PANEL)
4
3
PILOT
4
REAR
L1 L1
FRONT
PILOT
H1
7
7
F
2
H2
L2
3
1
R
2
5
H1
H2
L2
6
7
7
5
8
9
10
FRONT
REAR
9
10
3
4
1
6
6
5
6
2
R
2
F
8
R
DWD 11/12/02
-
-
75AFV
WIRING DIAGRAM 75AFV-120V
SK1917
STAR MANUFACTURING INTERNATIONAL INC.
#10 SUNNEN DRIVE, ST. LOUIS, MO. 63143, USA
FRACTIONS ±1/64 DECIMALS ±.005 ANGLES ±1°
TOLERANCES UNLESS OTHERWISE NOTED
DR.
DATE
CK.
-
-
-
-
-
THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.
NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.
FINISH
MATERIAL
TITLE
REVISIONS
LTR
MODEL NO.
DESCRIPTION OF CHANGEDATE
PART NO.
DR
1
3
4
41
42
38
37
9
18
17
21
20
10
13
MOUNT SPRING BETWEEN
FRAME & ARM HOLES
14
5
35
2
8
12
11
39
40
11
10
15
16
6
7
5
32
22
36
33
34
23
31
30
24
INFINITE CONTROLS
ELECTRONIC CONTROLS
19
NAMEPLATE
)4+..Ä/#:
™
ON
HEA
T
TI
M
E
(%
!
4
(/,$
RE
AR
HEA
T
T
I
ME
(%
!
4
HEA
T
TEM
P
FR
ONT
(/,$
H
EA
T
TE
M
P
S
e
a
l-M
a
x
™
OFF
33
31
30
23
29
28
17
REFER TO THE PARTS LIST SPECIFIC TO YOUR MODEL FOR MORE DETAIL INFORMATION.
STAR MANUFACTURING INTERNATIONAL INC.
SK2109 01-14-05
27
26
25
PARTS LIST May 8, 2006, Rev C
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
MODEL
Grill-Max Roller Grills
20 Series
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
INCLUDE MODEL AND SERIAL NUMBER OF
1
1
1 A5-RG2028 1 BODY ASSY 20CR/SCR
1 A5-RG2027 1 BODY ASSY 2OC/SC
2 A5-Z2184 1 DRIP TRAY 20C/SC
3 A5-Z8409 1 BACK-CHAIN RETAINER SPACER 20C/SC
4 A5-Z8410 1 ANGLE CHAIN RETAINER UPPER 20C/SC
5 A5-Z2169 2 SIDE PANEL 20C/SC
6 2N-Z2181 11 ELEMENT 120V 20 20C-120V
6 2N-Z2611 11 ELEMENT 230V 20 20C-230V
7 A5-Z6719 1 CHAIN GUIDE 20C/SC
8 2P-Z2242 1 CHAIN 20C/SC
9 PS-RG2029 11 ROLLER ASSY CHROME 20C
9 PS-RG2030 11 ROLLER ASSY POLY 20SC
10 2A-Z6614 3 IDLER ALL
11 2A-Z8017 3 BUSHING, IDLER ALL
12 A5-RG2042 1 ARM ASSY- CHAIN TENSIONER ALL
13 2P-Z8074 1 SPRING ALL
14 2P-Z2538 1 MOTOR SPROCKET ALL
15 2U-Z6485 1 MOTOR-120 VOLT ALL 120V MODELS
15 2U-Z6487 1 MOTOR-230/240 VOLT ALL 230/240V MODELS
16 A5-RG2046 1 MOTOR MOUNTING ASSY 20C/SC
17 A5-RG2036 1 CORD ASSY 120V 20C/SC (120V MODELS EXCEPT CSA)
17 2E-Z0512 1 CORD SET EUR 10AMP 20C/SC (230V MODELS)
18 2K-Y3240 1 CORD BUSHING 20C/SC (120V & 240V MODELS)
19 2E-Y9227 1 CORD INLET IEC320 10 AMP 20C/SC (230V MODELS)
20 A5-Z5335 1 BOTTOM COVER PLATE ALL
22 A5-Z9344 1 MOUNTING BRACKET 20C/SC
23 2J-Z2192 2 CONTROL 230/240 VOLT 20C/SC
23 2J-Z2195 2 CONTROL 120 VOLT 20C/SC
30 A5-Z7853 1 CONTROL PANEL 20C/SC
30 A5-RG2047 1 CONTROL PANEL 20SCE
31 2M-Z8323 1 CONTROL PANEL LABEL 20C
31 2M-Z8324 1 CONTROL PANEL LABEL 20SC
31 2M-Z9529 1 CONTROL PANEL LABEL 20SCE
32 2J-Z2329 3 PILOT LIGHT RED 20C/SC (120V & 240V MODELS)
32 2J-Z3157 3 PILOT LIGHT YELLOW 20C/SC (230V MODELS)
33 2E-Z1858 1 SWITCH-RED LIGHTED 120V & 240V MODELS
33 2E-Z3156 1 SWITCH-YELLOW LIGHTED 230V MODELS
34 2R-Z1854 2 KNOB W/SET SCREW 20C/SC
35 A5-Z2509 4 PANEL-INSULATOR 20C/SC
36 2P-Z6455 22 TUBE SEAL, SOLID 20C/SC
37 2I-Z2175 22 O-RING SEAL 20C/SC
38 2P-Z2174 22 TUBE GUIDE 20C/SC
39 2R-Z5846 4 LEGS 20C/SC
40 2K-Z2895 4 ANTI SHORT BUSHING ALL
41 A5-Z7650 1 ELEMENT RETAINER - UPPER 20C/SC
42 A5-Z7656 1 ELEMENT RETAINER - LOWER 20C/SC
58 2P-Z0584 1 TONGS ALL
NOT SHOWN 2E-Z3619 1 WIRE SET-230V
NOT SHOWN 2E-Z8320 1 WIRE SET-120V 20C/SC
NOT SHOWN PS-Z3018 -- TUBE ASSEMBLY SLEEVE
Number
Per
Unit
Description & Model Designation
Part
Number
Key
Number
PARTS LIST May 8, 2006, Rev C
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
MODEL
Grill-Max Roller Grills
30 Series
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
INCLUDE MODEL AND SERIAL NUMBER OF
1
2
Number
Per
Unit
Description & Model Designation
Part
Number
Key
Number
1 A5-RG3062 1 BODY ASSY 30C/SC
1 A5-RG3070 1 BODY ASSY 30CBB/SCBB
1 A5-RG3087 1 BODY ASSY 30CBBC/SCBBC
1 A5-RG3068 1 BODY ASSY 30CF/SCF
1 A5-RG3066 1 BODY ASSY 30CR/SCR
1 A5-RG3072 1 BODY ASSY 30CRBB/SCRBB
2 A5-Z2185 1 DRIP TRAY 30C/SC
3 A5-Z8409 1 BACK-CHAIN RETAINER SPACER 30C/SC
4 A5-Z8410 1 ANGLE CHAIN RETAINER UPPER 30C/SC
5 A5-Z2169 2 SIDE PANEL 30C/SC
5 A5-Z5401 2 SIDE PANEL 30CF/SCF
6 2N-Z2178 11 ELEMENT 120V 30/45 30C/SC-120V
6 2N-Z2194 11 ELEMENT 230V 30/45 30C/SC-230V
7 A5-Z6719 1 CHAIN GUIDE 30C/SC
8 2P-Z2242 1 CHAIN 30C/SC
8 2P-Z5384 1 CHAIN 30CF/SCF
9 PS-RG3077 11 ROLLER ASSY CHROME 30C
9 PS-RG3078 11 ROLLER ASSY POLY 30SC
10 2A-Z6614 3 IDLER ALL
11 2A-Z8017 3 BUSHING, IDLER ALL
12 A5-RG2042 1 ARM ASSY- CHAIN TENSIONER ALL
13 2P-Z8074 1 SPRING ALL
14 2P-Z2538 1 MOTOR SPROCKET ALL
15 2U-Z6485 1 MOTOR-120 VOLT ALL 120V MODELS
15 2U-Z6487 1 MOTOR-230/240 VOLT ALL 230/240V MODELS
16 A5-RG2046 1 MOTOR MOUNTING ASSY 30C/SC
16 A5-RG5040 1 MOTOR MOUNTING ASSY 30CF/SCF
17 A5-RG2036 1 CORD ASSY 120V 30C/SC (120V MODELS EXCEPT CSA)
17 2E-Z0512 1 CORD SET EUR 10AMP 30C/SC (230V MODELS)
18 2K-Y3240 1 CORD BUSHING 30C/SC (120V & 240V MODELS)
19 2E-Y9227 1 CORD INLET IEC320 10 AMP 30C/SC (230V MODELS)
20 A5-Z5335 1 BOTTOM COVER PLATE ALL
21 2P-Z1540 2 HOLE PLUG ALL EXCEPT CLEAR BUNBOX MODELS
(CBBC, SCBBC)
22 A5-Z9344 1 MOUNTING BRACKET 30C/SC
22 A5-RG4554 1 MOUNTING BRACKET ASSY 30CE/SCE
23 2J-Z2192 2 CONTROL 230/240 VOLT 30C/SC
23 2J-Z2195 2 CONTROL 120 VOLT 30C/SC
23 PS-RG3091 1 ELECTRONIC CONTROL 120V 30CE/SCE
23 A5-Z6002 1 ELECTRONIC CONTROL 230/240V 30CE/SCE
24 2K-Z1971 9 SPACERS 30CE/SCE
25 2E-Z5565-5 1 RIBBON CONNECTOR 30CE/SCE
26 2E-Z5565-3 1 SENSOR FRONT 30CE/SCE
27 2E-Z5565-4 1 SENSOR REAR 30CE/SCE
28 2E-Z5565-2 1 POWER BOARD 30CE/SCE
29 PS-RG3092 1 CONTROL BOARD 30CE/SCE
30 A5-Z7651 1 CONTROL PANEL 30C/SC
30 A5-Z7753 1 CONTROL PANEL 30CBB/SCBB
30 A5-RG3069 1 CONTROL PANEL 30CE/SCE
30 A5-RG3071 1 CONTROL PANEL 30CBBE/SCBBE
31 2M-Z8325 1 CONTROL PANEL LABEL 30C
31 2M-Z8326 1 CONTROL PANEL LABEL 30CBB
PARTS LIST May 8, 2006, Rev C
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
MODEL
Grill-Max Roller Grills
30 Series con't
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
INCLUDE MODEL AND SERIAL NUMBER OF
2
2
Number
Per
Unit
Description & Model Designation
Part
Number
Key
Number
31 2M-Z8328 1 CONTROL PANEL LABEL 30CBBE
31 2M-Z8327 1 CONTROL PANEL LABEL 30CE
31 2M-Z8329 1 CONTROL PANEL LABEL 30SC
31 2M-Z8330 1 CONTROL PANEL LABEL 30SCBB
31 2M-Z8331 1 CONTROL PANEL LABEL 30SCBBE
31 2M-Z8332 1 CONTROL PANEL LABEL 30SCE
32 2J-Z2329 3 PILOT LIGHT RED 30C/SC (120V & 240V MODELS)
32 2J-Z3157 3 PILOT LIGHT YELLOW 30C/SC (230V MODELS)
32 2J-Z2329 1 PILOT LIGHT RED 30CE/SCE (120V & 240V MODELS)
32 2J-Z3157 1 PILOT LIGHT YELLOW 30CE/SCE (230V MODELS)
33 2E-Z1858 1 SWITCH-RED LIGHTED 120V & 240V MODELS
33 2E-Z3156 1 SWITCH-YELLOW LIGHTED 230V MODELS
34 2R-Z1854 2 KNOB W/SET SCREW 30C/SC
35 A5-Z2509 4 PANEL-INSULATOR 30C/SC
36 2P-Z6455 22 TUBE SEAL, SOLID 30C/SC
37 2I-Z2175 22 ORING SEAL 30C/SC
38 2P-Z2174 22 TUBE GUIDE 30C/SC
39 2R-Z5846 4 LEGS 30C/SC
40 2K-Z2895 4 ANTI SHORT BUSHING ALL
41 A5-Z7650 1 ELEMENT RETAINER - UPPER 30C/SC
42 A5-Z7656 1 ELEMENT RETAINER - LOWER 30C/SC
42 A5-RG3094 1 ELEMENT RETAINER ASSY - LOW 30CE/SCE
45 2P-Z5098 11 GREASE SEAL 30CDV/SCDV
46 A5-Z5158 1 GRILL DIVIDER 30CDV/SCDV
47 2D-Z5898 1 PAN 2/3 X 4” DEEP 30CBB/SCBB
48 2P-Z0315 4 DRAWER ROLLER W/SCREW ALL BUNBOX (CBB/SCBB) MODELS
49 A5-RG3030 1 DRAWER ASSY 30CBB/SCBB
50 A5-RG3009 1 DRAWER FRONT ASSEMBLY 30CBB/SCBB
51 2M-Z2377 1 DRAWER LABEL 30CBB/SCBB
52 2A-Z4667 1 SHAFT 30CBBC/SCBBC
53 A5-Z4660 1 DOOR BRACKET 30CBBC/SCBBC
54 2C-Z4680 1 RETAINER RING 30CBBC/SCBBC
55 A5-Z4661 1 SPRING MOUNT BRACKET 30CBBC/SCBBC
56 A5-Z4657 1 DOOR ARM 30CBBC/SCBBC
57 2P-Z4683 1 EXTENSION SPRING 30CBBC/SCBBC
58 2P-Z0584 1 TONGS ALL
59 2A-Z4333 1 RETAINER PIN 30CBBC/SCBBC
60 2P-Z4337 1 COMPRESSION SPRING 30CBBC/SCBBC
61 2A-Z4332 1 SHOULDER SCREW 30CBBC/SCBBC
62 A5-RG3037 1 FRONT DOOR 30CBBC/SCBBC
62 A5-RG5016 1 FRONT DOOR-GLASS 30CBBC/SCBBC
NOT SHOWN 2E-Z8320 1 WIRE SET 30C/SC (INFINITE CONTROLS)
NOT SHOWN 2E-Z8414 1 WIRE SET 30CE/SCE (ELECTRONIC CONTROLS)
NOT SHOWN PS-Z3018 -- TUBE ASSEMBLY SLEEVE
PARTS LIST May 8, 2006, Rev C
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
MODEL
Grill-Max Roller Grills
45 Series
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
INCLUDE MODEL AND SERIAL NUMBER OF
1
2
Number
Per
Unit
Description & Model Designation
Part
Number
Key
Number
1 A5-RG4533 1 BODY ASSY 45C/SC
1 A5-RG4536 1 BODY ASSY 45CBB/SCBB
1 A5-RG4534 1 BODY ASSY 45CR/SCR
1 A5-RG4537 1 BODY ASSY 45CRBB/SCRBB
2 A5-Z2186 1 DRIP TRAY 45C/SC
3 A5-Z8411 1 BACK-CHAIN RETAINER SPACER 45C/SC
4 A5-Z8412 1 ANGLE CHAIN RETAINER UPPER 45C/SC
5 A5-Z2265 2 SIDE PANEL 45C/SC
5 A5-Z5347 2 SIDE PANEL 45CF/SCF
6 2N-Z2178 16 ELEMENT 120V 30/45 45C/SC-120V
6 2N-Z2194 16 ELEMENT 230V 30/45 45C/SC-230V
7 A5-Z6615 1 CHAIN GUIDE 45C/SC
8 2P-Z2266 1 CHAIN 45C/SC
8 2P-Z5336 1 CHAIN 45CF/SCF
9 PS-RG3077 16 ROLLER ASSY CHROME 45C
9 PS-RG3078 16 ROLLER ASSY POLY 45SC
10 2A-Z6614 3 IDLER ALL
11 2A-Z8017 3 BUSHING, IDLER ALL
12 A5-RG2042 1 ARM ASSY- CHAIN TENSIONER ALL
13 2P-Z8074 1 SPRING ALL
14 2P-Z2538 1 MOTOR SPROCKET ALL
15 2U-Z6485 1 MOTOR-120 VOLT ALL 120V MODELS
15 2U-Z6487 1 MOTOR-230/240 VOLT ALL 230/240V MODELS
16 A5-RG2046 1 MOTOR MOUNTING ASSY 45C/SC
16 A5-RG5040 1 MOTOR MOUNTING ASSY 45CF/SCF
17 A5-RG2036 1 CORD ASSY 120V 45C/SC (120V MODELS EXCEPT CSA)
17 2E-Z0512 1 CORD SET EUR 10AMP 45C/SC (230V MODELS)
17 A5-RG2041 1 CORD ASSY 120V 45C/SC (120V CSA MODELS)
18 2K-Y3240 1 CORD BUSHING 45C/SC (120V & 240V MODELS)
19 2E-Y9227 1 CORD INLET IEC320 10 AMP 45C/SC (230V MODELS)
20 A5-Z5335 1 BOTTOM COVER PLATE ALL
21 2P-Z1540 2 HOLE PLUG ALL EXCEPT CLEAR BUNBOX MODELS
(CBBC, SCBBC)
22 A5-Z9344 1 MOUNTING BRACKET 45C/SC
22 A5-RG4554 1 MOUNTING BRACKET ASSY 45CE/SCE
23 2J-Z2192 2 CONTROL 230/240 VOLT 45C/SC
23 2J-Z2195 2 CONTROL 120 VOLT 45C/SC
23 PS-RG3091 1 ELECTRONIC CONTROL 120V 45CE/SCE
23 A5-Z6002 1 ELECTRONIC CONTROL 230/240V 45CE/SCE
24 2K-Z1971 9 SPACERS 45CE/SCE
25 2E-Z5565-5 1 RIBBON CONNECTOR 45CE/SCE
26 2E-Z5565-3 1 SENSOR FRONT 45CE/SCE
27 2E-Z5565-4 1 SENSOR REAR 45CE/SCE
28 2E-Z5565-2 1 POWER BOARD 45CE/SCE
29 PS-RG3092 1 CONTROL BOARD 45CE/SCE
30 A5-Z7651 1 CONTROL PANEL 45C/SC
30 A5-Z7753 1 CONTROL PANEL ASSY 45CBB/SCBB
30 A5-RG3069 1 CONTROL PANEL 45CE/SCE
30 A5-RG3071 1 CONTROL PANEL 45CBBE/SCBBE
31 2M-Z8325 1 CONTROL PANEL LABEL 45C
31 2M-Z8326 1 CONTROL PANEL LABEL 45CBB
PARTS LIST May 8, 2006, Rev C
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
MODEL
Grill-Max Roller Grills
45 Series
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
INCLUDE MODEL AND SERIAL NUMBER OF
2
2
Number
Per
Unit
Description & Model Designation
Part
Number
Key
Number
31 2M-Z8327 1 CONTROL PANEL LABEL 45CE
31 2M-Z8329 1 CONTROL PANEL LABEL 45SC
31 2M-Z8330 1 CONTROL PANEL LABEL 45SCBB
32 2J-Z2329 3 PILOT LIGHT RED 45C/SC (120V & 240V MODELS)
32 2J-Z3157 3 PILOT LIGHT YELLOW 45C/SC (230V MODELS)
32 2J-Z2329 1 PILOT LIGHT RED 45CE/SCE (120V & 240V MODELS)
32 2J-Z3157 1 PILOT LIGHT YELLOW 45CE/SCE (230V MODELS)
33 2E-Z1858 1 SWITCH-RED LIGHTED 120V & 240V MODELS
33 2E-Z3156 1 SWITCH-YELLOW LIGHTED 230V MODELS
34 2R-Z1854 2 KNOB W/SET SCREW 45C/SC
35 A5-Z2510 4 PANEL-INSULATOR 45C/SC
36 2P-Z6455 32 TUBE SEAL, SOLID 45C/SC
37 2I-Z2175 32 ORING SEAL 45C/SC
38 2P-Z2174 32 TUBE GUIDE 45C/SC
39 2R-Z5846 4 LEGS 45C/SC
40 2K-Z2895 4 ANTI SHORT BUSHING ALL
41 A5-Z6619 1 ELEMENT RETAINER - UPPER 45C/SC
42 A5-Z6622 1 ELEMENT RETAINER - LOWER 45C/SC
42 A5-RG4549 1 ELEMENT RETAINER ASSY - LOW 45CE/SCE
45 2P-Z5098 16 GREASE SEAL 45CDV/SCDV
46 A5-Z5157 1 GRILL DIVIDER 45CDV/SCDV
47 2D-Z5898 1 PAN 2/3 X 4” DEEP 45CBB/SCBB
48 2P-Z0315 4 DRAWER ROLLER W/SCREW ALL BUNBOX (CBB/SCBB) MODELS
49 A5-RG3030 1 DRAWER ASSY 45CBB/SCBB
50 A5-RG3009 1 DRAWER FRONT ASSEMBLY 45CBB/SCBB
51 2M-Z2377 1 DRAWER LABEL 45CBB/SCBB
58 2P-Z0584 1 TONGS ALL
NOT SHOWN 2E-Z8320 1 WIRE SET 45C/SC (INFINITE CONTROLS)
NOT SHOWN 2E-Z8414 1 WIRE SET 45CE/SCE (ELECTRONIC CONTROLS)
NOT SHOWN PS-Z3018 -- TUBE ASSEMBLY SLEEVE
PARTS LIST May 8, 2006, Rev C
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
MODEL
Grill-Max Roller Grills
50 Series
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
INCLUDE MODEL AND SERIAL NUMBER OF
1
2
Number
Per
Unit
Description & Model Designation
Part
Number
Key
Number
1 A5-RG5028 1 BODY ASSY 50 C/SC
1 A5-RG5029 1 BODY ASSY 50 CR/SCR
1 A5-RG5031 1 BODY ASSY 50CBB/SCBB
1 A5-RG5037 1 BODY ASSY 50CBBC/SCBBC
1 A5-RG5030 1 BODY ASSY 50CF/50SCF
1 A5-RG5032 1 BODY ASSY 50CRBB/SCRBB
2 A5-Z2305 1 DRIP TRAY 50C/SC
2A A5-Z4273 1 DRIP TRAY 50SC-ST, 50SCE-ST, 50SC-STS
2B A5-RG5012 1 DRIP TRAY ASSY 50SC-ST, 50SCE-ST, 50SC-STS
3 A5-Z8409 1 BACK-CHAIN RETAINER SPACER 50C/SC
4 A5-Z8410 1 ANGLE CHAIN RETAINER UPPER 50C/SC
5 A5-Z2169 2 SIDE PANEL 50C/SC
5 A5-Z5401 2 SIDE PANEL 50CF/SCF
6 2N-Z2179 11 ELEMENT 120V 50 50C/SC-120V
6 2N-Z2193 11 ELEMENT 230V 50/75 50C/SC-230V
7 A5-Z6719 1 CHAIN GUIDE 50C/SC
8 2P-Z2242 1 CHAIN 50C/SC
8 2P-Z5384 1 CHAIN 50CF/SCF
9 PS-RG7562 11 ROLLER ASSY CHROME 50C
9 PS-RG7563 11 ROLLER ASSY POLY 50SC
10 2A-Z6614 3 IDLER ALL
11 2A-Z8017 3 BUSHING, IDLER ALL
12 A5-RG2042 1 ARM ASSY- CHAIN TENSIONER ALL
13 2P-Z8074 1 SPRING ALL
14 2P-Z2538 1 MOTOR SPROCKET ALL
15 2U-Z6485 1 MOTOR-120 VOLT ALL 120V MODELS
15 2U-Z6487 1 MOTOR-230/240 VOLT ALL 230/240V MODELS
16 A5-RG2046 1 MOTOR MOUNTING ASSY 50C/SC
16 A5-RG5040 1 MOTOR MOUNTING ASSY 50CF/SCF
17 A5-RG2036 1 CORD ASSY 120V 50C/SC (120V MODELS EXCEPT CSA)
17 2E-Z0512 1 CORD SET EUR 10AMP 50C/SC (230V MODELS)
18 2K-Y3240 1 CORD BUSHING 50C/SC (120V & 240V MODELS)
19 2E-Y9227 1 CORD INLET IEC320 10 AMP 50C/SC (230V MODELS)
20 A5-Z5335 1 BOTTOM COVER PLATE ALL
21 2P-Z1540 2 HOLE PLUG ALL EXCEPT CLEAR BUNBOX
MODELS (CBBC, SCBBC)
22 A5-Z9344 1 MOUNTING BRACKET 50C/SC
22 A5-RG4554 1 MOUNTING BRACKET ASSY 50CE/SC
23 2J-Z2192 2 CONTROL 230/240 VOLT 50C/SC
23 2J-Z2195 2 CONTROL 120 VOLT 50C/SC
23 PS-RG3091 1 ELECTRONIC CONTROL 120V 50CE/SCE
23 A5-Z6002 1 ELECTRONIC CONTROL 230/240V 50CE/SCE
24 2K-Z1971 9 SPACERS 50CE/SCE
25 2E-Z5565-5 1 RIBBON CONNECTOR 50CE/SCE
26 2E-Z5565-3 1 SENSOR FRONT 50CE/SCE
27 2E-Z5565-4 1 SENSOR REAR 50CE/SCE
28 2E-Z5565-2 1 POWER BOARD 50CE/SCE
29 PS-RG3092 1 CONTROL BOARD 50CE/SCE
30 A5-Z7751 1 CONTROL PANEL 50C/SC
30 A5-Z7850 1 CONTROL PANEL ASSY 50CBB/SCBB
30 A5-RG7560 1 CONTROL PANEL 50CBBE/SCBBE
30 A5-RG7561 1 CONTROL PANEL 50CE/SCE
31 2M-Z8333 1 CONTROL PANEL LABEL 50C
PARTS LIST May 8, 2006, Rev C
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
MODEL
Grill-Max Roller Grills
50 Series
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
INCLUDE MODEL AND SERIAL NUMBER OF
2
2
Number
Per
Unit
Description & Model Designation
Part
Number
Key
Number
31 2M-Z8334 1 CONTROL PANEL LABEL 50CBB
31 2M-Z8336 1 CONTROL PANEL LABEL 50CBBE
31 2M-Z8335 1 CONTROL PANEL LABEL 50CE
31 2M-Z8337 1 CONTROL PANEL LABEL 50SC
31 2M-Z8338 1 CONTROL PANEL LABEL 50SCBB
31 2M-Z8340 1 CONTROL PANEL LABEL 50SCBBE
31 2M-Z8339 1 CONTROL PANEL LABEL 50SCE
32 2J-Z2329 3 PILOT LIGHT RED 50C/SC (120V & 240V MODELS)
32 2J-Z3157 3 PILOT LIGHT YELLOW 50C/SC (230V MODELS)
32 2J-Z2329 1 PILOT LIGHT RED 50CE/SC (120V & 240V MODELS)
32 2J-Z3157 1 PILOT LIGHT YELLOW 50CE/SC (230V MODELS)
33 2E-Z1858 1 SWITCH-RED LIGHTED 120V & 240V MODELS
33 2E-Z3156 1 SWITCH-YELLOW LIGHTED 230V MODELS
34 2R-Z1854 2 KNOB W/SET SCREW 50C/SC
35 A5-Z2509 4 PANEL-INSULATOR 50C/SC
36 2P-Z6455 22 TUBE SEAL, SOLID 50C/SC
37 2I-Z2175 22 ORING SEAL 50C/SC
38 2P-Z2174 22 TUBE GUIDE 50C/SC
39 2R-Z5846 4 LEGS 50C/SC
40 2K-Z2895 4 ANTI SHORT BUSHING ALL
41 A5-Z7650 1 ELEMENT RETAINER - UPPER 50C/SC
42 A5-RG3094 1 ELEMENT RETAINER - ASSY 50CE/SCE
42 A5-Z7656 1 ELEMENT RETAINER - LOWER 50C/SC
45 2P-Z5098 11 GREASE SEAL 50CDV/SCDV
46 A5-Z5158 1 GRILL DIVIDER 50CDV/SCDV
47 2D-Z5899 1 PAN FULL X 4” DEEP 50CBB/SCBB
48 2P-Z0315 4 DRAWER ROLLER W/SCREW ALL BUNBOX (CBB/SCBB) MODELS
49 A5-RG5011 1 DRAWER ASSY 50CBB/SCBB
50 A5-RG5004 1 DRAWER FRONT ASSEMBLY 50CBB/SCBB
51 2M-Z2380 1 DRAWER LABEL 50CBB/SCBB
52 2A-Z4677 1 SHAFT 50CBBC/SCBBC
53 A5-Z4660 1 DOOR BRACKET 50CBBC/SCBBC
54 2C-Z4680 1 RETAINER RING 50CBBC/SCBBC
55 A5-Z4661 1 SPRING MOUNT BRACKET 50CBBC/SCBBC
56 A5-Z4657 1 DOOR ARM 50CBBC/SCBBC
57 2P-Z4683 1 EXTENSION SPRING 50CBBC/SCBBC
58 2P-Z0584 1 TONGS ALL
59 2A-Z4333 1 RETAINER PIN 50CBBC/SCBBC
60 2P-Z4337 1 COMPRESSION SPRING 50CBBC/SCBBC
61 2A-Z4332 1 SHOULDER SCREW 50CBBC/SCBBC
62 A5-RG5016 1 FRONT DOOR-GLASS 50CBBC/SCBBC
NOT SHOWN 2E-Z8320 1 WIRE SET 50C/SC (INFINITE CONTROLS)
NOT SHOWN 2E-Z8414 1 WIRE SET 50CE/SCE (ELECTRONIC CONTROLS)
NOT SHOWN PS-Z3018 -- TUBE ASSEMBLY SLEEVE
PARTS LIST May 8, 2006, Rev C
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
MODEL
Grill-Max Roller Grills
75 Series
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
INCLUDE MODEL AND SERIAL NUMBER OF
1
2
Number
Per
Unit
Description & Model Designation
Part
Number
Key
Number
1 A5-RG7549 1 BODY ASSY 75CRBB/SCRBB
1 A5-RG7571 1 BODY ASSY 75CFV
1 A5-RG7547 1 BODY ASSY 75CF/SCF
1 A5-RG7548 1 BODY ASSY 75CBB/SCBB
1 A5-RG7546 1 BODY ASSY 75 CR/SCR
1 A5-RG7545 1 BODY ASSY 75 C/SC
2 A5-Z2306 1 DRIP TRAY 75C/SC
3 A5-Z8411 1 BACK-CHAIN RETAINER SPACER 75C/SC
4 A5-Z8412 1 ANGLE CHAIN RETAINER UPPER 75C/SC
5 A5-Z5347 2 SIDE PANEL 75CF/SCF
5 A5-Z2265 2 SIDE PANEL 75C/SC
6 2N-Z2193 16 ELEMENT 230V 50/75 75C/SC-230V
6 2N-Z2982 16 ELEMENT 120V 105 W 75C/SC-120V
7 A5-Z6615 1 CHAIN GUIDE 75C/SC
8 2P-Z5336 1 CHAIN 75CF/SCF
8 2P-Z2266 1 CHAIN 75C/SC
9 PS-RG7563 16 ROLLER ASSY POLY 75SC
9 PS-RG7562 16 ROLLER ASSY CHROME 75C
10 2A-Z6614 3 IDLER ALL
11 2A-Z8017 3 BUSHING, IDLER ALL
12 A5-RG2042 1 ARM ASSY- CHAIN TENSIONER ALL
13 2P-Z8074 1 SPRING ALL
14 2P-Z2538 1 MOTOR SPROCKET ALL
15 2U-Z6487 1 MOTOR-230/240 VOLT ALL 230/240V MODELS
15 2U-Z6485 1 MOTOR-120 VOLT ALL 120V MODELS
16 A5-RG5040 1 MOTOR MOUNTING ASSY 75CF/SCF
16 A5-RG2046 1 MOTOR MOUNTING ASSY 75C/SC
17 A5-RG2034 1 CORD SER 240V W/TERMINALS 75C/SC (240V MODELS)
17 2E-Y9251 1 CORD SET EUR 16 AMP 75C/SC (230V MODELS)
17 A5-RG2041 1 CORD ASSY 120V 75C/SC (120V MODELS)
18 2K-Y3240 1 CORD BUSHING 75C/SC (120V & 240V MODELS)
19 2E-Y9253 1 CORD INLET IEC320 16 AMP 75C/SC (230V MODELS)
20 A5-Z5335 1 BOTTOM COVER PLATE ALL
21 2P-Z1540 2 HOLE PLUG ALL EXCEPT CLEAR BUNBOX
MODELS (CBBC, SCBBC)
22 A5-RG4554 1 MOUNTING BRACKET ASSY 75CE/SCE
22 A5-Z9344 1 MOUNTING BRACKET 75C/SC
23 A5-Z6002 1 ELECTRONIC CONTROL 230/240V 75CE/SCE
23 PS-RG3091 1 ELECTRONIC CONTROL 120V 75CE/SCE
23 2J-Z2192 2 CONTROL 230/240 VOLT 75C/SC
23 2J-Z2195 2 CONTROL 120 VOLT 75C/SC
24 2K-Z1971 9 SPACERS 75CE/SCE
25 2E-Z5565-5 1 RIBBON CONNECTOR 75CE/SCE
26 2E-Z5565-3 1 SENSOR FRONT 75CE/SCE
27 2E-Z5565-4 1 SENSOR REAR 75CE/SCE
28 2E-Z5565-2 1 POWER BOARD 75CE/SCE
29 PS-RG3092 1 CONTROL BOARD 75CE/SCE
30 A5-RG7560 1 CONTROL PANEL 75CE/SCE
30 A5-RG7561 1 CONTROL PANEL 75CBBE/SCBBE
30 A5-Z7850 1 CONTROL PANEL ASSY 75CBB/SCBB
30 A5-Z7751 1 CONTROL PANEL 75C/SC
31 2M-Z8339 1 CONTROL PANEL LABEL 75SCE
31 2M-Z8340 1 CONTROL PANEL LABEL 75SCBBE
PARTS LIST May 8, 2006, Rev C
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
MODEL
Grill-Max Roller Grills
75 Series
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
INCLUDE MODEL AND SERIAL NUMBER OF
2
2
Number
Per
Unit
Description & Model Designation
Part
Number
Key
Number
31 2M-Z8338 1 CONTROL PANEL LABEL 75SCBB
31 2M-Z8337 1 CONTROL PANEL LABEL 75SC
31 2M-Z8335 1 CONTROL PANEL LABEL 75CE
31 2M-Z8336 1 CONTROL PANEL LABEL 75CBBE
31 2M-Z8334 1 CONTROL PANEL LABEL 75CBB
31 2M-Z8333 1 CONTROL PANEL LABEL 75C
32 2J-Z3157 1 PILOT LIGHT YELLOW 75CE/SCE (230V MODELS)
32 2J-Z2329 1 PILOT LIGHT RED 75CE/SCE (120V & 240V MODELS)
32 2J-Z3157 3 PILOT LIGHT YELLOW 75C/SC (230V MODELS)
32 2J-Z2329 3 PILOT LIGHT RED 75C/SC (120V & 240V MODELS)
33 2E-Z3156 1 SWITCH-YELLOW LIGHTED 230V MODELS
33 2E-Z1858 1 SWITCH-RED LIGHTED 120V & 240V MODELS
34 2R-Z1854 2 KNOB W/SET SCREW 75C/SC
35 A5-Z2510 4 PANEL-INSULATOR 75C/SC
36 2P-Z6455 32 TUBE SEAL, SOLID 75C/SC
37 2I-Z2175 32 ORING SEAL 75C/SC
38 2P-Z2174 32 TUBE GUIDE 75C/SC
39 2R-Y5092 4 LEGS 4” 75C/SC
40 2K-Z2895 4 ANTI SHORT BUSHING ALL
41 A5-Z6619 1 ELEMENT RETAINER - UPPER 75C/SC
42 A5-RG4549 1 ELEMENT RETAINER ASSY - LOW 75CE/SCE
42 A5-Z6622 1 ELEMENT RETAINER - LOWER 75C/SC
43 2P-Y9176 2 SNAP BUTTON 75SCF-SA, 75SCFE-SA
44 A5-RG7516 1 CONTROL PANEL COVER 75SCF-SA, 75SCFE-SA
45 2P-Z5098 16 GREASE SEAL 75CDV/SCDV
46 A5-Z5157 1 GRILL DIVIDER 75CDV/SCDV
47 2D-Z5899 1 PAN FULL X 4” DEEP 75CBB/SCBB
48 2P-Z0315 4 DRAWER ROLLER W/SCREW ALL BUNBOX (CBB/SCBB) MODELS
49 A5-RG5011 1 DRAWER ASSY 75CBB/SCBB
50 A5-RG5004 1 DRAWER FRONT ASSEMBLY 75CBB/SCBB
51 2M-Z2380 1 DRAWER LABEL 75CBB/SCBB
58 2P-Z0584 1 TONGS ALL
NOT SHOWN 2E-Z8414 1 WIRE SET 75CE/SCE (ELECTRONIC CONTROLS)
NOT SHOWN 2E-Z8320 1 WIRE SET 75C/SC (INFINITE CONTROLS)
NOT SHOWN PS-Z3018 -- TUBE ASSEMBLY SLEEVE
6
PROGRAMACIÓN
Los controles electrónicos proporcionan ajustes
electrónicos para HEAT (Calentar) y HOLD
(conservar-mantener) para una variedad
de productos comestibles y condiciones de
instalación.
Para programar la parrillera electrónica de rodillos:
1. Con la parrillera encendida, oprima y mantenga
conjuntamente por 3 segundos el y del
lado que desee programar hasta que se emita
un sonido de alarma (beep) y la pantalla se
blanquee.
2. Para programar la temperatura de calentamiento
y/o el tiempo de calentamiento, oprima el
botón de HEAT (calentar). El último tiempo
de calentamiento salvado será mostrado en
la pantalla, la luz (LED) del HEAT (calentar)
titilará y el HEAT TIME (indicador de tiempo
de calentamiento) se encenderá (ON). Use los
botones y para ajustar el tiempo deseado,
luego oprima el botón de HEAT (calentar) de
nuevo. La luz (LED) del HEAT TIME (indicador
de tiempo de calentamiento) se apagará y
la luz (LED) del HEAT TEMP (indicador de
temperatura) se encenderá. Cuando haya
terminado de programar la temperatura, oprima
el botón HEAT (calentar) una vez más para salir
del modo de programación.
3. Para programar la temperatura de conservación
(hold temperature), repita el paso 1 de arriba,
luego oprima el botón HOLD. La última
temperatura de conservación salvada se
mostrará en la pantalla y la luz (LED) del HOLD
estará encendida. Use los botones y para
ajustar la temperatura deseada, luego oprima
el botón HOLD de nuevo para salir del modo de
programación.
4. Para quitar el calor de la sección frontal o
posterior, oprima y mantenga el botón de la
sección específi ca durante 3 segundos. La
palabra “OFF” aparecerá en la pantalla. Para
encender la sección de nuevo, oprima los
botones de HEAT o HOLD.
Arranque
El equipo con control electrónico entra en el modo
de conservación (HOLD) cuando se enciende por
primera vez. La pantalla ( display ) titilará hasta que
la temperatura previamente fi jada sea alcanzada.
El equipo emitirá un sonido (beep) una vez que
llegue a la temperatura. Equipos con control infi nito
no indican cuando la temperatura de operación es
alcanzada.
Calentamiento
El ajuste apropiado de la temperatura de
calentamiento depende del tamaño, contenido,
forma del producto y de la instalación de cualquier
escudo protector o pantalla de protección sanitaria
(protección contra estornudos) La Fundación
Nacional de Sanidad (NSF) requiere que todos
los productos comestibles perecederos sean
mantenidos a 140ºF o por encima durante el período
de servido.
Los productos deben ser mantenidos refrigerados
hasta que estén listos para ser utilizados. Los
tiempos de calentamiento varían dependiendo de la
temperatura inicial y de la calidad del producto. Para
mejores resultados, utilice salchichas elaboradas
para parrilleras.
Antes de cocinar por primera vez, lave los rodillos
con un paño suave húmedo con una solución
suave de agua jabonosa. Cuando las parrilleras
controladas de forma electrónica son encendidas
por primera vez, las pantallas titilarán, indicando
la temperatura de HOLD (conservación) hasta que
alcance la temperatura prefi jada.
Con la parrillera precalentada a la temperatura de
HOLD (conservación), cárguela con el producto
deseado y oprima el botón de HEAT (calentar).
La parrillera entrará en la modalidad de HEAT
(calentar) y las pantallas titilarán hasta que se
alcance la temperatura prefi jada. Después del ciclo
de calentamiento, la parrillera emitirá una alarma
o sonido (beep) cuatro veces y el producto estará
a la temperatura de servir.
Nota: basado en el tipo de producto a calentar, es
necesario experimentar de forma que se alcance
la temperatura de calentamiento HEAT y el tiempo
de calentamiento para llevar el producto a la
temperatura apropiada en un tiempo aceptable.
5
PROCEDIMIENTOS OPERATIVOS PARA PARRILLERAS ELECTRONICAS
™
™
PAT. # 6,782,802 PAT. # 6,707,015
MADE IN
U.S.A.
PAT. # 6,393,971
)4+..Ä/#:241
Seal-Max
DURATEC
™
PAT. # 6,782,802 PAT. # 6,707,015
Tabla de Controles Electrónicos
INSTALACION CONTINUED
El equipo debe ser conectado en forma directa e individual a la toma de alimentación eléctrica
de la pared. Si se conecta a un circuito sobrecargado, el equipo no operará de forma correcta.
Los modelos equipados con cajas para panes deben ser nivelados para utilizar la característica
de auto-cerrado en la gaveta de los panes. 4 patas ajustables están incluidas en la serie 75
y están disponibles de forma opcional para los otros modelos.
PROCEDIMIENTOS OPERATIVOS GENERALES
El interruptor principal controla toda la energía del equipo; éste se encuentra ubicado en el
panel de controles. Cuando el interruptor principal está en la posición ON, los rodillos estarán
encendidos, pero no suministrarán calor a menos que los controles de calor (HEAT) estén en la
posición de ON. Para mayor fl exibilidad de la sección de calentamiento (HEAT) la parrilla está
dividida en dos secciones controladas de forma individual. El control de la derecha controla el
calor de la sección posterior y el control de la izquierda regula el calor de la sección frontal. El
interruptor principal está iluminado para indicar cuando el equipo está prendido. En las parrilleras
con controlador infi nito una luz (LED) ubicada arriba de cada control señala cuando la sección
específi ca esta encendida (ON). También hay una luz (LED) adicional al fi nal de la cubierta
del equipo. Esta luz (LED) indica la posición el interruptor principal cuando la gaveta opcional
para los panes o la puerta del comercializador obstruyen la vista del panel de control. En los
modelos equipados con la caja para panes se requiere remover la gaveta de los panes para
retirar la bandeja de los panes y la bandeja de drenaje cuando el acceso a la parte posterior
del equipo está obstruida. Para remover la gaveta de los panes tome la gaveta por ambos
lados y hálela hacia fuera. Levante el frente para desenganchar la rueda del riel-guía y retire
la gaveta del equipo. Tenga precaución y evite que se caiga la gaveta cuando llegue al fi nal
del riel-guía. Para reinsertar la gaveta, primero deslice y enganche la guía de la gaveta en la
rueda frontal y luego la rueda trasera. No opere el equipo sin la bandeja de drenaje.
PRECAUCION
SOLO UTILICE UTENSILIOS PLÁSTICOS O RECUBIERTOS CUANDO MANEJE
PRODUCTOS COMESTIBLES. OBJETOS DE METAL PUEDEN DAÑAR LA
CUBIERTA DE LOS RODILLOS Y AFECTAR LA CAPACIDAD SANITARIA DE LOS
RODILLOS
PRECAUCION
NO UTILICE UTENSILIOS DE LANA DE ACERO O LIMPIADORES ABRASIVOS
EN LOS RODILLOS. RASPADURAS INVALIDARÁN LA GARANTÍA. PARA EVITAR
QUEMADURAS Y HERIDAS TOME LAS PRECAUCIONES NECESARIAS CUANDO
LIMPIE LA PARRILLA Y ESTA ESTÉ CALIENTE.
Limpieza
Antes de utilizar el equipo por primera vez, limpie los rodillos con un paño suave húmedo con
una solución suave de agua jabonosa. No utilice utensilios de metal cuando esté cocinando.
Las raspaduras y rayas le restarán habilidad para limpiar los rodillos de forma fácil. Nunca utilice
lanillas o esponjas metálicas o limpiadores abrasivos en los rodillos. Esto dañará el acabado
y los soportes de los rodillos. Los rodillos son más fáciles de limpiar cuando están calientes.
Tome las precauciones necesarias cuando limpie la parrilla y esté caliente de forma que se evite
heridas y quemaduras. Limpie los rodillos con un paño húmedo. Seque desde los extremos
hacia el centro para prevenir que el sucio sea forzado dentro de los sellos de los rodillos.. No
permita que los restos de la comida se adhieran y se quemen sobre la superfi cie del rodillo. El
exterior del equipo debe ser limpiado con un detergente suave y no abrasivo. Limpie todo el
equipo diariamente para garantizar la vida larga, buen funcionamiento y apariencia atractiva.
No utilice equipos con chorros de agua a presión (water jet) para limpiarlo.
4
PRECAUCION
Esta unidad ha sido diseñada y se vende exclusivamente para usos comerciales y para ser
operada por personal debidamente entrenado y experimentado en su operación y no se vende
para uso del consumidor en la casa o alrededor de ella ni para ser usada directamente por
la sociedad general en instalaciones de servicio de comidas. Favor contacte la fábrica para
equipos de uso para público en general.
INSTALACION
Este equipo está diseñado para operar con el voltaje y número de vatios indicados en la placa
de identifi cación montada en el respaldo de la unidad, y ha sido diseñado para ser usado con
corriente eléctrica alterna (AC) únicamente.
PRECAUCION
NO CONECTE ESTA UNIDAD A UNA FUENTE DE CORRIENTE DIRECTA (DC)
CARGA DE CONEXIÓN:
3
TABLA DE CONTENIDO
PAGINA NUMERO
CARGA DE CONEXION 3
INSTRUCCIONES OPERATIVAS GENERALES 3
LIMPIEZA 4
CONTROLDADOS ELECTRONICAMENTE:
ARRANQUE, CALENTAMIENTOI & PROGRAMACION 5
GARANTIA 6
DIAGRAMA DE CABLEADO 7-10
DESGLOSE DEL EQUIPO 11, 12
LISTA DE PARTES
MODELO SERIES 20 13
MODELO SERIES 30 14, 15
MODELO SERIES 45 16, 17
MODELO SERIES 50 18, 19
MODELO SERIES 75 20, 21
CONTROL INFINITO
MODELO SERIE VATIAJE
20C, 20SC 930
30C, 30SC, 30CF, 30SCF, 30CBB, 30CBBC,
30SCBB, 30CDV 1150
45C, 45SC, 45CBB, 45SCBB, 45CDV 1650
50C, 50SC, 50CF, 50SCF, 50CBB, 50CBBC,
50SCBB, 50CDV 1535
75C, 75SC, 75CBB, 75SCBB, 75FF,
75SCF 208/240V 1810/2400
75C, 75SC, 75CBB, 75SCBB,
75CDV 230V 2210
75C, 75CF, 75SC, 75SCF, 75CBB,
75SCBB, 75CDV 120V 1700
75CFV 120V 2880
CONTROL ELECTRONICO
MODELO SERIE VATAJE
20SCE 930
30CE, 30SCE, 30SCEX, 30CBBE
30SCBBE 1150
45SCE, 45SCRE 1650
50CE, 50SCE, 50SCEX 50CBBE, 50SCBBE,
50CBBES 1535
75CE, 75SCE, 75CBBE, 75CBBES,
75SCBBE, 75SCRE 208/240V,
75SCFE 1810/2400
75CE, 75SCE, 75CBBE,
75SCBBE, 75SCRE 120V 1730
2
Este símbolo intenta alertar el usuario a la presencia de
instrucciones de operación y mantenimiento importante en
el manual que acompaña el aparato.
GUARDA ESTE MANUAL PARA REFERENCIA EN
EL FUTURO.
AVISO
El uso de cualquier parte aparte de partes genuinos proveídos de la fabrica Star
exime al fabricante de toda responsabilidad.
Star reserva el derecho de cambiar las especifi caciones y el diseño del producto
sin notifi cación. Estas revisiones no dan al comprador un derecho a estos cam-
bios, mejoramientos, adiciones, o piezas de recambio correspondientes para
equipo previamente comprado.
Por los cambios periódicos del diseño, método, procedimiento, política, y regu-
lación, las especifi caciones en este manual pueden cambiar sin aviso. Aunque
Star Manufacturing hace todo que puede para asegurar que provee información
correcta, no somos responsables por errores u omisiones en la información
proveída ni por conclusiones formados como resulta de usar las especifi caciones.
Cuando usa la información proveída, el usuario acepta todo el riesgo asociado
con el uso de esta unidad.
MANTENIMIENTO Y REPARACIONES
Póngase en contacto con su comerciante de quien usted compró la unidad para servicio y mantenimiento
requerido. Por favor apunta en el área abajo el número de modelo, número serial, voltaje, y fecha de
compra y tenga esta información lista cuando usted llama para asegurar servicio rápido.
Símbolo de seguridad
N° Modelo
N° Serial
Voltaje
Fecha de Compra
Para información sobre la garantía, póngase en
contacto con su comerciante.
2
®
®
®
PARRILLERA
ROLLER
MODEL
20C, 30C, 45C, 50C & 75C
Controles Electrónico e Infi nito
Instrucciones para
instalación y
operación
2M-Z9106 Rev. C 5/8/06
30SCBB
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Grill-Max 75CFV Instrucciones de operación
- Categoría
- Barbacoas
- Tipo
- Instrucciones de operación
En otros idiomas
Documentos relacionados
Otros documentos
-
Holman Cooking/Star Mfg 30SCHDM Instrucciones de operación
-
Star Manufacturing 50SCHDM-120V Instrucciones de operación
-
Star PST14D-230-1 El manual del propietario
-
Pro-Max CG10I-230V Especificación
-
Acson SL30C Guía de instalación
-
McQuay CE 35C Guía de instalación
-
-
Sammic BE-40/C Manual de usuario
-
Pramac S2800 Manual de usuario
