Modern Forms PD-30854 Cinema Instrucciones de operación

Modern Forms
Marca
Modern Forms
Modelo
PD-30854 Cinema
Tipo
Instrucciones de operación
modernforms.com Headquarters/Eastern Distribution Center Central Distribution Center Western Distribution Center
Phone (800) 526.2588 44 Harbor Park Drive 1600 Distribution Ct 1750 Archibald Avenue
Fax (800) 526.2585 Port Washington, NY 11050 Lithia Springs, GA 30122 Ontario, CA 91760
G0 Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program. 1
HARDWARE
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
INSTALLATION INSTRUCTION
308 – LED Pendant
PD-30854
Wire Connector Plastic Anchor Junction Box Screw Wood Screw Mounting Screw Allen Screw Allen Wrench
Qty: 7pcs+1 Extra Qty: 2pcs+1 Extra Qty: 2pcs+1 Extra Qty: 2pcs+1 Extra Qty: 1 Extra Qty: 4 Extra Qty: 1pc
A B C D E F G
2
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.
INSTALLATION INSTRUCTION
308 – LED Pendant
PD-30854
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
CONNECTING THE WIRES Fig. 2
3. Remove the mounting screw (E) from the mounting back plate.
4. Drill holes in the wall aligned with the key holes located in the mounting back plate, insert the plastic anchors (B).
6OTDSFXUIF"MMFO4DSFX(VTJOH"MMFOXSFODI'QVMMPVUUIFFYUSBTBGFUZDPSETUISPVHIDMBNQMFBWFBMPPQGPSIPPLJOHUIFOTFDVSF
UIFTBGFUZDPSETXJUIDMBNQCZUJHIUJOHUIF"MMFOTDSFXIPPLUIFIPPLTJOUPUIFTBGFUZDPSEMPPQ
6OTDSFXUIF)FYBHPOBM/VUUBLFPVUUIFTXJWFM$IPPTFTVJUBCMFSPEGPSEFTJSFEMFOHUI5ISFBEUIFGJYUVSFXJSFBOEFYUSBTBGFUZDPSET
UISPVHIUIFSPETTXJWFMand canopy. Connect the canopy, swivel, rods and GJYUVSF.BLFTVSFBMMBSFUJHIUFOFEUIFOTDSFXVQUIFTXJWFM
BTCFGPSF
 Connect the driver input wires and output wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. If your outlet box
has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the
mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
9.Secure mounting back plate to the junction box using junction box screws (C). Fasten it to the ceiling using the wood screws (D).The side of
the mounting plate marked “GND” must face out. Pull out the driver output wire.
10.Hook the GPVS safety cords to the mounting plateTMPU.
Fig.1
G0
14FDVSFUIFGJYUVSFPOUPNPVOUJOHCBDLQMBUFXJUINPVOUJOHTDSFX&
12. Insert the crystal into the xture; secure it with Allen screw (G) using Allen wrench (F) and make sure it is unshakeable.
8.  Please follow these if shortening the wire is needed. Take note or take picture of how the wires are being connected and label each wire
clearly. Using the Fig. 4 as given below as reference.
MOUNTING THE FIXTURE (Fig. 1 )
/PUF5IFGJYUVSFFYDFFETMCTBOENVTUCFJOTUBMMFEVTJOHBOPVUMFUCPY6-BQQSPWFEGPSVQUPMCT
U.L. Approved 100LB. Max.
Outlet Box and Hardware
( Sold Separately )
Crystal
Pla
s
tic Anchor
Mounting Screw
Mounting Backplate
Air Craft Cable
Wood Screw
Junction Box Screw
Wire Connector
Hexagonal Nut
Junction Box
B
Driver(3 3/8" L x 2 3/8" W x 1 1/8"H)
6" Rod
Safety Cords
Canopy
Allen Wrench
Allen Screw
Pull
Allen Screw
Allen Wrench
A
C
D
E
F
G
(RPL-GLA-30815)
12" Rod12" Rod
3
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.
Fig. 2 Wiring
Fixture Wires House Wires
Black or Black
Smooth (Hot)
Fixture Wires House Wires
White or White
Ribbed (Neutral)
Fixture Wires
Bare wire
(Ground)
Back Plate Dimensions
G0
13
4"
41
4"
13
8"
House Wires
Green or Bare Copper
(Ground)
271
2"
235
8"
Fig. 3
Turn to down
INSTALLATION INSTRUCTION
308 – LED Pendant
PD-30854
Driver
I
nput
Out
put
Black
-Hot
White -
Neutral
Driver
I
nput
Out
put
Black
-Hot
White -
Neutral
-+
Black
-Hot
White -
Neutral
-+
LED Diagram
Fig. 4 Diagram
  • Page 1 1
  • Page 2 2
  • Page 3 3

Modern Forms PD-30854 Cinema Instrucciones de operación

Modern Forms
Marca
Modern Forms
Modelo
PD-30854 Cinema
Tipo
Instrucciones de operación
Descargar PDF
informe

En otros idiomas

Documentos relacionados