SCAN 1010 Series Assembly And Instruction Manual

Marca: SCAN

Modelo: 1010 Series

Categoría: Estufas

Tipo: Assembly And Instruction Manual

SCAN A/S - DK-5492 VISSENBJERG

Scan 1010 Series

Congratulations on your new Scan wood-burning stove

You have purchased a product by one of Europe’s leading manufacturer’s of wood-burning stoves, and we are sure that you will have years of pleasure

with your purchase. To make the best possible use of your stove, it is important that you follow our advice and instructions.

Please read this Assembly- and instructions manual before you start to assemble your stove.

Product registration number

Please indicate the product registration number at any enquiry

ASSEMBLY- AND INSTRUCTIONS MANUAL

Table of contents

Technical data ........................................................................................................ 3

Installation

Safety

Technical data and dimensions

Dimension sketch

Type plate

Product registration number

Additional accessories

Loose parts

Assembly .................................................................................................................. 8

Remove packaging

Positioning your wood-burning stove

Load bearing foundation

Distances to combustible floor.

Distance to furniture

Radiance distance to combustible objects

Distances to combustible floor.

Storage of ﬂammable material

Carrying capacity

Distance to flammable materials, shown with insulated flue pipe

Distance to flammable materials, shown with un-insulated flue pipe

Distance to ﬁrewall

Mounting with plinth

Mounting of the wall bracket

Burn chamber

Existing chimney and pre-fabricated element chimney

Connection between stove and steel chimney

Requirements for chimney

Connection with 90° elbow pipe

Fresh air intake

Closed combustion system

Instruction for use ............................................................................................. 20

CB technique

Primary air

Secondary air

Bafﬂe plates

Indicator for control of air supply

Instructions for heating ................................................................................... 21

Lighting

Handling fuel

Maintenance ........................................................................................................ 23

Troubleshooting .................................................................................................. 24

Defra ....................................................................................................................... 25

CONTENTS

Installation

To ensure best-possible functionality and safety for your installation, we advise you to call a professional fitter. Our Scan Dealer will be able to

recommend a qualified fitter in your area. For information on Scan Dealers, please go to http://scan.dk.

When you install any kind of fireplace or stove, you must inform the local authorities. You are also responsible for calling in a chimney sweep to

inspect and authorize the installation.

The house owner is responsible for ensuring that all necessary national, European and local safety measures are observed during installation and

fitting and also responsible for observing the fitting and operating instructions detailed in this manual.

Safety

Any changes made to the product by the dealer, installer or user could result in the product and safety functions not functioning as intended. The

same applies to the fitting of accessories or extra equipment not supplied by Scan A/S. This could also be the case if parts that are necessary

for the operation and safety of the stove are dismantled or removed.

WARNING

This product contains very strong magnets.

• When separating and putting together the magnets, we recommend that you let them glide on (or from) one another. In this way you avoid

squeezing your fingers and damaging the coating of the magnets.

• Electronic components should be kept at a safe distance from the magnets to avoid them being influenced or damaged by the magnetic field

(pacemakers, hearing aids, computers, watches, measuring instruments, floppy discs, credit cards, mobile phones etc.).

TECHNICAL DATA

Test in compliance with EN 13229

Scan 1010 Technical data Unit

CO Emission at 13% O

0,1 %

CO Emission at 13% O

1246 mg/Nm

Dust @ 13% O

12 mg/Nm

@ 13% O

41 mg/Nm

Efficiency 82 %

Energy efﬁciency index

109,9

Energy efﬁciency class

A+

Nominel output 7 kW

Chimney temperature EN 13229 220 °C

Temperature in connecting piece 264 °C

Amount of smoke 7,4 g/sek

Sub-pressure EN 13229 12 Pa

Recommended sub-pressure in connecting piece 16 - 18 Pa

Required combustion air supply 19,8 Nm

Fuel Wood

Fuel consumption 2,2 kg/h

Amount of fuel 1,7 kg

Technical data and dimensions

Materials: ................................ Steel plate, galvanised sheet,

Vermicolite, Chamotte, Robax glass

Surface treatment: .......................................................................... Senotherm

Max. wood length: ..................................................................................... 50 cm

Weight Scan 1010: .....................................................................approx 135 kg

Weight big box:...............................................................................approx 32 kg

Weight little box:............................................................................approx 20 kg

Connecting piece internal diameter: .............................................. 144 mm

Connecting piece external diameter: .............................................. 148

Approval type: ................................................................ Intermittent fuelling

Intermittent fuelling means normal use of a woodstove. In other

words, you should let the fire die down until only the embers are left,

before refuelling.

The Scan 1010 was build in compliance with the homologized product

type specified in the Assembly- and Instructions Manual provided

with the product.

The DoP declaration of performance is available from scan.dk

Please note:

You get the best use of the stove by using a

”top-down lighting”, see page 21.

TECHNICAL DATA

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010005.idw

91010005

målskitse Scan 1010

13-04-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

479

649

324,5 D

143 D

799

399 B

399 D

324,5 B

TECHNICAL DATA

Dimension sketch Scan 1010

A Centre rear outlet

B Top outlet

C Height to the beginning of the

connecting piece at top outlet

D Centre of fresh air intake bottom

F Fresh air intake at the back of the stove

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010008.idw

91010008

Mål ovn, base, sokkel

20-05-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

649

324,5 B

479

324,5 D

143 D

TECHNICAL DATA

Dimension sketch Scan 1010

A Centre rear outlet

B Top outlet

C Height to the beginning of the

connecting piece at top outlet

D Centre of fresh air intake bottom

F Fresh air intake at the back of the stove

109

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010034.idw

91010034

vægbeslag løse

12-08-2016

mbp

Scan 1010

VÆGT:

AREAL:

N/A

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010033.idw

91010033

Friskluft skjuler

12-08-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

TECHNINIAI DUOMENYS

TECHNICAL DATA

Large wall bracket

Small wall bracket

Large module

- is not to be

used under the

stove!

Small module

Cover for

fresh air inlet

Large module

with fresh air

inlet and heat

shield.

Large plinth

Small plinth

Additional accessories

XX00000

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010003.idw

91010003

Ovn bag

23-05-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010010.idw

91010010

indpakning

24-05-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

Scan 1010

Freestanding room heater fired by solid fuel

Standard:

Fuel type:

Operation type:

The appliance can be operated in a shared flue.

Country

EN 13240 DoP 91010600

Wood

Intermittent

EUR

Norway

Austria

Classification

Intermittent

Klasse 2

15a B-VG

Certificate/Standard

EN 13240

300-ELAB-1588-NS

300-ELAB-1588-AUS

Approved by

Teknologisk Institut

Dust at 13% O2: 12 mg/Nm³

Flue gas temperature: 220°C

Nominal heat output: 7 kW

Efficiency: 82%

Scan A/S DK 5492 Vissenbjerg

Minimum distance to combustible materials:

Side: 500 mm - Back: 150 mm - Front: 1400 mm

CO emission at 13% O2:

See assembly- and instructions manual

Follow assembly- and instructions manual.

Use only recommended fuels.

Montage- und Bedienungsanleitung beachten.

Verwenden Sie nur empfohlene Brennstoffe.

1000 08-2017

0,10% 1246 mg/Nm³

Schweiz

Germany

LRV 11

Stufe 2

VKF

1. BlmSchV

Teknologisk Institut

TECHNICAL DATA/ASSEMBLY

Type plates

All Scan wood-burning stoves are fitted with a type plate, that speci-

fies the approval standards and the distance to flammable materials.

The type plate is located at the back of the stove.

Product registration number

All wood-burning stoves are provided with a product registration

number.

The product registration number is located at the back of the stove.

Please make a note of this number on the front page as you will

always have to state it when contacting your dealer or Scan A/S.

Type plate

Product

registration

number

Loose parts

• Glove

• Connecting piece

• Gasket for connecting piece

• Screws for connecting piece 5 x 12 mm

• Connecting piece for fresh air inlet

• Screws for connecting piece/fresh air 4 x 10 mm

• Decor ring for top outlet

• Screw M5x6 (UK)

Additional accessories

• Large/small module

• Large/small plinth

• Large/small wall bracket

• Protection glass for large/small module

• Magnets

• Cover for fresh air inlet

• Small floor plate (glass or steel)

• Large floor plate (glass or steel)

Disposal of packaging

Your Scan stove may come supplied with the following packaging:

Wood packaging:

The wood packaging can be reused and after final use can be incine-

rated as a CO2 neutral product or sent for recycling.

Flamingotop:

Send for recycling or waste disposal.

Foam:

Send for recycling or waste disposal.

Plastic bags:

Send for recycling or waste disposal.

Stretch film/plastic film:

Send for recycling or waste disposal.

Scan 1010

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:

EMNE:

C:\Working Folder\Designs\Scan 64\90064049.idw

90064049

Brændbar + uisoleret røgrør - Scan 64 uden sideglas

23-08-12

Scan 64

VÆGT:

AREAL:

N/A

150

350

340

595

100

363

628

100

Min. 400 mm

Min. 1400 mm

Min.

140 mm

Min.

140 mm

Positioning your wood-burning stove

The wood-burning stove must be set up so that the stove itself, the

flue pipe, and the chimney can all be cleaned.

Load bearing underlay

All of the products in our portfolio are classified as light-duty firepla-

ces; in most cases, there is no need to reinforce the floor, so that you

can typically use the normal floor.

However, you should make sure that the load bearing underlay can

bear the weight of the wood-burning stove and that of the chimney.

Distance to furniture: 1400 mm

But please check to avoid furniture or other furnishings being dried

out due to being too close to the stove.

All national and local requirements concerning safety distances for

wood burning stoves must be respected.

If you connect the stove to a steel chimney, the safety distances of

the steel chimney must also be respected.

Radiance distance to combustible objects out-

side the modules.

Distances to combustible floor.

Remember to place a floor plate.

ASSEMBLY

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010013.idw

91010013

opbevaring af brænde

30-05-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

Scan A/S

DK-5492 Vissenbjerg

TG.NR:

EMNE:

C:\Working Folder\Designs\Scan 1010\21010909.iam

21010909

assembly of fresh air box

12-04-2016

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Max

MAX

* * *

* *

** *

= 10 mm

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010043.idw

91010043

moduler

16-09-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

Max

MAX

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010043.idw

91010043

moduler

16-09-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

285 285

KGKG

Storage of flammable material

You can store wood under

the stove in the module

with heat shield and fresh

air inlet.

ASSEMBLY

Carrying capacity

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:

EMNE:

C:\Working Folder\Designs\Scan 64\90064049.idw

90064049

Brændbar + uisoleret røgrør - Scan 64 uden sideglas

23-08-12

Scan 64

VÆGT:

AREAL:

N/A

150

350

340

595

100

363

628

100

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:

EMNE:

C:\Working Folder\Designs\Scan 64\90064049.idw

90064049

Brændbar + uisoleret røgrør - Scan 64 uden sideglas

23-08-12

Scan 64

VÆGT:

AREAL:

N/A

150

350

340

595

100

363

628

100

500

400

150

Distance to flammable materials, shown with insulated flue pipe*

Distance to flammable materials, shown with un-insulated flue pipe*

The distances presuppose the use of an insulated flue pipe with min. 30 insulation all the way to the stove.

Parallel rear wall installation

45° Corner installation

ASSEMBLY

Scan 1010

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010051.idw

91010051

Scan 1010 - Montage røgstuds i topafgang

12-02-2018

ken

Scan 1010

VÆGT:

AREAL:

N/A

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Scan A/S

DK-5492 Vissenbjerg

TG.NR:

EMNE:

C:\Working Folder\Designs\Scan 64\90064047.iam

90064047

Brandmur og isoleret røgrør - Scan 64 uden sideglas

29-08-12

Scan 64

VÆGT:

AREAL:

N/A

100

700

960

700

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Scan A/S

DK-5492 Vissenbjerg

TG.NR:

EMNE:

C:\Working Folder\Designs\Scan 64\90064047.iam

90064047

Brandmur og isoleret røgrør - Scan 64 uden sideglas

29-08-12

Scan 64

VÆGT:

AREAL:

N/A

100

700

960

700

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Scan A/S

DK-5492 Vissenbjerg

TG.NR:

EMNE:

C:\Working Folder\Designs\Scan 64\90064047.iam

90064047

Brandmur og isoleret røgrør - Scan 64 uden sideglas

29-08-12

Scan 64

VÆGT:

AREAL:

N/A

100

700

960

700

1000

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Scan A/S

DK-5492 Vissenbjerg

TG.NR:

EMNE:

C:\Working Folder\Designs\Scan 64\90064047.iam

90064047

Brandmur og isoleret røgrør - Scan 64 uden sideglas

29-08-12

Scan 64

VÆGT:

AREAL:

N/A

100

700

960

700

350

1000

300

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010051.idw

91010051

Scan 1010 - Montage røgstuds i topafgang

12-02-2018

ken

Scan 1010

VÆGT:

AREAL:

N/A

Distance to firewall*

110 mm brick or other material with a corresponding insulation ability.

The indicated distances are valid for insulated as well as un-insulated smoke pipes.

Flammable material

Firewall

ASSEMBLY

* All national and local requirements concerning safety distances for wood burning stoves must be respected.

Scan 1010

Connecting piece

The insert is prepared for a top flue outlet from the factory.

The flue connection piece (A), gasket for the flue connection piece (B), screws (C) and cover ring (D)

can be found in the stove’s combustion chamber.

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010018.idw

91010018

expl. tegning

08-06-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010019.idw

91010019

Emb afbræk

10-06-2016

hms

Scan 1010

VÆGT:

AREAL:

0,04 kg

20656 mm^2

DIM.:

Scan A/S

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010014.idw

91010014

sokkel magnet

31-05-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010015.idw

91010015

justering af sokkel

08-06-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

A ( 0,40 : 1 )

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010039.idw

91010039

indstil ben

23-08-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

First mount the module with fresh air inlet on the plinth and then the stove. Place the magnets on the

next modules before mounting them.

Please follow the order below A, B, C, D, and E.

It is important to adjust the plinths before mounting the modules.

Press the two distance triangles out of the packing. These are used for the proper

mounting of the magnets. The magnets are to be found inside the plinth at the delivery.

Mounting with plinth

ASSEMBLY

ccc

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010020.idw

91010020

vægbeslag

13-06-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010029.idw

91010029

afmont. af dæksler

21-06-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010027.idw

91010027

Varmeskjold afmont.

20-06-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

Scan 1010 Wall

Wall mounted room heater fired by solid fuel

Standard:

Fuel type:

Operation type:

The appliance can be operated in a shared flue.

Country

EN 13240 DoP 91010601

Wood

Intermittent

EUR

Norway

Austria

Classification

Intermittent

Klasse 2

15a B-VG

Certificate/Standard

EN 13240

300-ELAB-1588-NS

300-ELAB-1588-AUS

Approved by

Teknologisk Institut

Dust at 13% O2: 12 mg/Nm³

Flue gas temperature: 220°C

Nominal heat output: 7 kW

Efficiency: 82%

Scan A/S DK 5492 Vissenbjerg

Minimum distance to combustible materials:

Side: 500 mm - Front: 1400 mm - Bottom: 400 mm

CO emission at 13% O2:

See assembly- and instructions manual

Follow assembly- and instructions manual.

Use only recommended fuels.

Montage- und Bedienungsanleitung beachten.

Verwenden Sie nur empfohlene Brennstoffe.

1000 08-2017

0,10% 1246 mg/Nm³

Schweiz

Germany

LRV 11

Stufe 2

VKF

1. BlmSchV

Teknologisk Institut

Scan 1010 Wall

Wall mounted room heater fired by solid fuel

Standard:

Fuel type:

Operation type:

The appliance can be operated in a shared flue.

Country

EN 13240 DoP 91010601

Wood

Intermittent

EUR

Norway

Austria

Classification

Intermittent

Klasse 2

15a B-VG

Certificate/Standard

EN 13240

300-ELAB-1588-NS

300-ELAB-1588-AUS

Approved by

Teknologisk Institut

Dust at 13% O2: 12 mg/Nm³

Flue gas temperature: 220°C

Nominal heat output: 7 kW

Efficiency: 82%

Scan A/S DK 5492 Vissenbjerg

Minimum distance to combustible materials:

Side: 500 mm - Front: 1400 mm - Bottom: 400 mm

CO emission at 13% O2:

See assembly- and instructions manual

Follow assembly- and instructions manual.

Use only recommended fuels.

Montage- und Bedienungsanleitung beachten.

Verwenden Sie nur empfohlene Brennstoffe.

1000 08-2017

0,10% 1246 mg/Nm³

Schweiz

Germany

LRV 11

Stufe 2

VKF

1. BlmSchV

Teknologisk Institut

Scan 1010 Wall

Wall mounted room heater fired by solid fuel

Standard:

Fuel type:

Operation type:

The appliance can be operated in a shared flue.

Country

EN 13240 DoP 91010601

Wood

Intermittent

EUR

Norway

Austria

Classification

Intermittent

Klasse 2

15a B-VG

Certificate/Standard

EN 13240

300-ELAB-1588-NS

300-ELAB-1588-AUS

Approved by

Teknologisk Institut

Dust at 13% O2: 12 mg/Nm³

Flue gas temperature: 220°C

Nominal heat output: 7 kW

Efficiency: 82%

Scan A/S DK 5492 Vissenbjerg

Minimum distance to combustible materials:

Side: 500 mm - Front: 1400 mm - Bottom: 400 mm

CO emission at 13% O2:

See assembly- and instructions manual

Follow assembly- and instructions manual.

Use only recommended fuels.

Montage- und Bedienungsanleitung beachten.

Verwenden Sie nur empfohlene Brennstoffe.

1000 08-2017

0,10% 1246 mg/Nm³

Schweiz

Germany

LRV 11

Stufe 2

VKF

1. BlmSchV

Teknologisk Institut

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010048.idw

91010048

røgstuds

06-10-2016

hms

Scan 1010

VÆGT:

AREAL:

0,61 kg

69343 mm^2

DIM.:

Scan A/S

Mounting of the wall bracket

First dismount the heat shield at the rear. The heat shield is not used on the wall model.

Pull the stove out of the module. Mount the fittings (A) at the top and the two adjustment fittings (B) at the bottom. If you want a rear outlet,

the cover plate (C) on the back of the stove must be removed and placed in the top outlet. Fit the connecting piece with the supplied gasket and

screws (D). The cover plate (E) at the rear of the module must also be removed. Place the type plate (F).

Mount the fittings in the same way on the other modules.

Is not to be

used on the wall

model.

Please note

that the delivered type plate must

be placed on the stove after dis-

mounting the heat shield.

ASSEMBLY

Content:

Small wall bracket + number plate

Content:

Large wall bracket + number plate

Place the delivered

type plate.

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010032.idw

91010032

Ophængs mål

08-08-16

Scan 1010

VÆGT:

AREAL:

N/A

118,6

109

99,3

291

835

98,1

270

gulv

Min. 400 mm

Min. 874 mm

91± 2 mm

Wall-hung model

Installation must be planned and executed in accordance with natio-

nal and local building regulations.

The stove must only be fitted to a non-flammable wall. There must be

no form of flammable component in the wall. In the case of thin walls,

nor must there be any behind the wall. The load-bearing capacity of

the wall must be checked under all circumstances.

To ensure correct installation we recommend that a building expert

be commissioned to plan and outline the installation with a view to

subsequent approval.

For wall installation we recommend using the wall brackets supplied.

If a chimney is installed on top of a wall-hung model, the chimney

must be fully self-supporting. It must not rest on the wood-burning

stove. There must be a distance of at least 6 mm between the first

section and the flange on the flue collar. Please consult a specialist.

Scan A/S disclaims all liability for the installation of wall-hung

wood-burning stoves.

Dimensional drawings of the wall brackets

Combustible floor

ASSEMBLY

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010022.idw

91010022

opboring af beslag

14-06-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010031.idw

91010031

væg step by step

28-06-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

91±2

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010030.idw

91010030

vægbeslag justering

28-06-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010023.idw

91010023

justerskive

14-06-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

A ( 1 : 2 )

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010045.idw

91010045

indikatorplade

19-09-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

A ( 1 : 2 )

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010045.idw

91010045

indikatorplade

19-09-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

The smoke pipe should be lead 9 1±2

mm out of the wall in order for it to

fit on the stove’s connecting piece.

See dimensional drawing.

1) Drill the holes with the drilling template (a)

2) Replace the drilling template (a) with the

adjustment template (b)

3) Can be adjusted up and down. Use a spirit level.

4) Mount the module (A) on the wall fitting.

Place the stove (B). Put on the indicator plate (C).

Mounting of the wall bracket

ASSEMBLY

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010042.idw

91010042

opstilling med knærør

25-08-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010046.idw

91010046

ovn med 90 gr røgrør

21-09-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:

EMNE:

C:\Working Folder\Designs\Scan 1001\91001011.idw

91001011

Brændkammerforing, eksploderet

18-04-2012

Scan 1001

VÆGT:

AREAL:

N/A

Existing chimney and pre-fabricated element

chimney

If you intend to connect your stove to an existing chimney, it makes

sense to contact an authorised Scan dealer, or a local chimney sweep

for advice. These experts will also let you know if your flue needs

renovating.

When connecting a pre-fabricated element chimney, follow the

manufacturer’s connection instructions for the relevant chimney

type.

Connection between stove and steel chimney

Your Scan dealer, or local chimney sweep, can advise you on choosing

a make and type of steel chimney. This ensures that the chimney

will match your wood-burning stove. As a general rule, the length of

the flue should not be less than 3,5 m measured from the top of the

wood-burning stove.

Some weather or installation conditions might require another

length.

Choosing the wrong length or diameter of steel chimney could impair

functionality.

Always observe the chimney vendor‘s instructions precisely.

Requirements for chimney

The chimney must be labelled T400 and G for soot testing.

Connection with 90° elbow pipe

If you intend to use an elbow pipe with the Scan 1010 we recommend

the use of a curved elbow pipe to improve the draft.

If you are connecting your stove using a sharp elbow bend, the clea-

nout door should be in the vertical section, such that the horizontal

part can be cleaned through it.

Curved elbow pipe

Sharp elbow pipe

Baffle plate

in steel

Baffle plate

in vermicu-

lite

Combustion chamber lining

ASSEMBLY

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1001\91001041.idw

91001041

Nederste røgvenderplade

15-05-2012

Scan 1001

VÆGT:

AREAL:

N/A

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1001\91001041.idw

91001041

Nederste røgvenderplade

15-05-2012

Scan 1001

VÆGT:

AREAL:

N/A

8.4.

Place the bottom stones with the inclined edge

turning to the rear and downwards.

Place the log guard against the front of the

insert.

The rear burn chamber plates must be mounted

so that the holes of the plates are placed preci-

sely over the tertiary holes of the insert.

Mount the lower baffle plate. The baffle plate

must be supported by the rear plates.

Mount the pins and put

the plate in place.

Burn chamber

Note that the baffle plates are made of porous, ceramic material, and can break. Exercise care when working.

Mount the rear plates. The side plates keep the

rear plates in place, so that these do not fall over.

Mount the left burn chamber plate.

Mount the right burn chamber plate.

ASSEMBLY

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010038.idw

91010038

friskstuds bag

18-08-16

Scan 1010

VÆGT:

AREAL:

N/A

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010036.idw

91010036

Frisklfuft bund

18-08-16

Scan 1010

VÆGT:

AREAL:

N/A

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010003.idw

91010003

Ovn bag

23-05-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010037.idw

91010037

dækplade friskluft

18-08-16

Scan 1010

VÆGT:

AREAL:

N/A

Fresh air intake

In a well-insulated house, the air used up by the burning process has to

be replaced. This particularly applies to houses with mechanical ven-

tilation. There are different ways of making sure that an air exchange

takes place. The most important thing is to ensure that there is a sup-

ply of air to the room where the wood stove is located. The external

wall vent must be located as close to the wood stove as possible, and

you must be able to close it when you are not using the wood stove.

Beware that the valve in the outer wall cannot be covered by accident!

National and local building regulations must be followed with regard

to the connection of fresh-air intake.

Closed combustion system

You should use the closed combustion system for the wood-burning

stove if you live in a newly-built, airtight home. Outside air for com-

bustion is connected through a ventilation pipe via the wall or floor.

It must be possible to shut off the ventilation pipe with a valve, when

the stove is not in use.

• Minimum Ø100 mm ventilation pipe, maximum length: 6 m with

a maximum of one bend

The connecting piece for external combustion air is to be found in the

packaging.

If the external combustion air is connected at the rear, the dis-

mounted plate must be mounted on the hole for external air in the

bottom of the stove.

NOTE: if the stove has a fresh air connexion or closed combustion,

the ventilation pipe must be open, when the stove is in use!

Mounting of external air supply

Dismount the cover plate behind or below the casette

Mount the Ø100 sleeve.

Mounting of external air supply

on the rear of the cassette.

Dismount the cover plate at the rear and mount it in the bottom.

Mounting of external air supply

on the bottom of the cassette.

Mount the Ø100 sleeve.

Ø100 sleeve

External combustion

air on the bottom of

the cassette

External air

supply on the

rear of the cas-

sette

ASSEMBLY

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010004.idw

91010004

CB teknik

18-03-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

0% - 100%

NAVN:

STI:

M3 NR.:

MATERIALE:

DATO:

SIGN:

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1010\91010047.idw

91010047

indikator luft

21-09-2016

hms

Scan 1010

VÆGT:

AREAL:

N/A

DIM.:

Scan A/S

0% - 100%

Baffle plate

CB-technique

Primary air

Secondary air

Primary air

Log guard

Secondary air

Adjustment of air supply

CB-technique (Clean Burning)

The wood-burning stove is equipped with CB technology. In order

to ensure an optimal combustion of released gases under the inci-

neration process, air will pass through a specially developed canal

system. The heated air is led into the combustion chamber through

the small holes at the rear of the burn chamber. This airflow is driven

by the combustion rate and thus cannot be regulated.

Primary air

The primary air regulation mechanism is used for lighting the fire, or

to boost the burning process when you put wood on. The primary air

vent can be 0 - 30% open if you use hard wood fuel such as oak and

beech. You can close the primary air vent if you use soft wood such

as birch or pine for fuel.

Settings for normal load: 0 - 30%

Secondary air

Secondary air is pre-heated and fed indirectly to the fire. At the

same time, the secondary airflow cleans the glass pane to avoid soot

build-up. If you over-restrict the secondary airflow, soot can build up

on the glass pane. The secondary airflow determines the heat output

from your wood stove.

Settings for normal load: 50 - 70%

Baffle plates

The baffle plates are located in the upper part of the combustion

chamber. The plates hold back smoke, making sure it stays inside

the combustion chamber for a longer time before escaping through

the chimney. This reduces the smoke gas temperature as the gases

have more time to dissipate heat to the wood-burning stove. The

baffle plates must be removed for sweeping; see „Maintaining your

wood-burning stove“. Note that the baffle plates are made of porous,

ceramic material, and can break. Exercise care when working. The

baffle plates are subject to wear and tear, and are not covered by

the warranty.

INSTRUCTIONS FOR HEATING

ASSEMBLY

Continuous firing

It is important to reach as high a temperature as possible in the

combustion chamber. This makes the most efficient use of the wood

stove and fuel, and ensures a clean burning process. At the same

time, this avoids soot build-up on the combustion chamber walls and

glass. While the stove is lit, you should not see any smoke, but just air

movement that indicates the burning process.

After completing the lighting phase, you should have a good layer of

embers in the wood stove; you can then start stoking up the stove.

Lay 1-3 pieces of wood, of about max 1,7 kg weight with max 10 cm

diameter and a length of about 25 cm onto the fire.

Note! The wood must catch fire quickly; this is why we recommend

setting the primary airflow to full power. Running the stove at too low

a temperature and with too little primary air can lead to deflagration

of the gases, and thus cause damage to the stove.

When stoking up with wood, always open the glass door carefully to

avoid smoke escaping. Never stoke up with wood while the fire is still

burning nicely.

Environmentally-Friendly Heating

Avoid restricting your wood-burning stove to an extent where no

flames are visible during the degasifying period, as this leads to

particularly inefficient heating. The gases released by the wood do

not burn due to the low temperature in the combustion chamber. Part

of the gas condenses in the wood-burning stove and flue system as

soot, and this could lead to your chimney catching fire. The smoke

that exits the chimney is bad for the environment and has an unple-

asant smell.

Lighting

We recommend the use of fire starters, or similar products, which are

available from your Scan dealer. Using fire starters helps to light the

wood quicker, and keeps the burning process clean.

Never use liquid lighting fuels!

"Top down" lighting

Important! Always use a top-down lighting. The stove is constructed

for this in order to give the best exploitation.

4 pieces of wood approx. 25 cm long with a weight of approx. 0.6 –

0.8 kg per piece (image 1)

The wood must not cover the bottom entirely and must never be pla-

ced higher than the Clean-Burn rail at the rear of the stove.

12 - 20 thin sticks of about 20 cm with a total weight of approx. 1,0-

1,2 kg (image 3 - 4). 4 fire starters (image 5).

Place logs, sticks and fire starters in the combustion chamber as

shown on images 1 - 5.

Set the primary and secondary airflow controls to maximum for

about 20 - 30 minutes. When the larger pieces of wood have caught

fire properly, you can set the primary and secondary airflow to the

desired level.

"Top down" lighting gives a more environmentally friendly start to

your fire and helps to keep the glass area as clean as possible.

INSTRUCTIONS FOR HEATING

Using your stove in the spring or autumn

In the transition period (spring/autumn), where there is less need for

heating, we recommend to make a single „top down“ lighting, perhaps

with one stoke up to ensure that the combustion chamber lining burns

clean again.

Why you need a chimney

The chimney is the wood-burning stove‘s motor; it‘s performance

decides how well your stove will work. The draft in the chimney crea-

tes a vacuum in the wood-burning stove. The vacuum draws the smoke

out of the stove, and takes in air through the combustion air baffle to

fuel the burning process. Combustion air is also used for the airwash

system that keeps the window clear of soot.

The draft in the chimney is caused by the difference in temperatures

inside and outside the chimney. The higher the temperature differen-

ce is, the better the draft in the chimney will be. It is thus important

for the chimney to reach operating temperature before you adjust

the damper to restrict combustion in the stove (a brickwork chimney

will take longer to reach operating temperature than a steel chim-

ney). It is very important to reach operating temperature as quickly

as possible on days on which the draft in the chimney is poor due to

unfavorable wind and weather conditions. Make sure the fuel ignites

as quickly as possible (with visible flames). Chop the wood into parti-

cularly small pieces; use an extra fire lighter etc.

After longer periods of disuse, check the chimney flue for blockage.

You can connect several units to the same chimney. But make sure

check with your chimney sweep to observe local regulations.

No matter how good your chimney is, it will not perform well if you do

not use it correctly. On the other hand a poor chimney, may give you

acceptable results if you use it correctly.

Using your stove in various weather conditions

Wind blowing on the chimney can have a great effect on how your

stove reacts in various wind conditions; you may need to adjust

the airflow to achieve good burning results. Fitting a damper in the

flue pipe may also help as it will give you the ability to regulate the

draught in changing wind conditions.

Fog can also have a great influence on how well a chimney draws; you

may again need to adjust the airflow settings to achieve good burning

results.

General Notes

Please note! Parts of the wood-burning stove, especially the outer

surfaces, become hot during use. Please exercise due care.

Never empty ashes into a flammable container. Ashes can contain

glowing embers long after you finish using your wood stove.

While the stove is not in use you can close the valves to avoid draught

through the stove.

After longer breaks you should check the smoke outlet paths for

blockages before lighting.

Chimney fires

In case of a chimney fire, keep the stove door and the valves on the

stove closed. In case of emergency, call the fire service.

It is recommended that you get a chimney sweep to check the chim-

ney before using the stove again.

Handling fuels

Selecting Wood/Fuel

You can use any type of wood as firewood, however, harder types,

such as beech, ash, are generally better for heating as they burn more

evenly and create less ash. Other wood types like maple, birch and

spruce are excellent alternatives.

Handling

Firewood is best if you fell the tree, and saw and split the wood,

before May 1st. Remember to cut the logs to match the size of your

wood-burning stove‘s combustion chamber. We recommend a dia-

meter of 6-10 cm. The length should be about 6 cm shorter than that

of the combustion chamber to leave enough space for air to circulate.

Firewood with a greater diameter needs splitting. Split wood dries

faster.

Storing

You need to store the sawn and split firewood in a dry place for 1-2

years before burning. Wood dries faster if you stack it in an airy place.

Before use, store the firewood for a few days at room temperature.

Note that wood absorbs moisture during the autumn and winter

seasons.

Moisture

To avoid environmental issues, and for optimum burning, wood has to

be perfectly dry to be suitable for use as firewood. The max. residual

moisture in the wood should not exceed 20%. A moisture content of

15-18% yields best results. As an easy way of checking if wood is

dry, just knock two pieces of wood together. If the wood is moist, the

sound will be dull.

If you use damp wood, most of the heat it produces will be used to

evaporate the water. The temperature in the wood stove does not

rise, and the room is not sufficiently heated. Of course, this is not

economical, and it will cause soot build up on the glass pane, in the

stove, and in the chimney. Burning moist wood also causes pollution.

Understanding units for measuring wood

Various units of measurement are used for wood. Before you buy wood,

it makes sense to familiarise yourself with the terms. There are various

brochures, in public libraries for example, that cover this topic.

Use of the following as fuel is illegal

Painted, pressure impregnated, or glued wood, driftwood from the

sea. Never burn chipboard, plastics, or chemically treated paper.

These materials are dangerous to humans, to the environment, your

wood stove, and your chimney. To keep a long story short – make sure

you burn only quality firewood.

Firewood fuel value

The fuel value is different for different types of wood. In other words,

you need to use more wood of certain types to achieve the same hea-

ting performance. This Instruction Manual assumes that you will be

using beech, which has a very high fuel value, and is also a wood that

is easy to procure. If you use oak or beech wood fuel, note that these

wood types have a greater fuel value than, say, birch. Make sure you

use less fuel to avoid damage to the wood-burning stove.

Wood types Kg Dry wood/m

Compared to

beech

Hornbeam 640 110%

Beech/Oak 580 100%

Ash 570 98%

Maple 540 93%

Birch 510 88%

Pine 480 83%

Fir 390 67%

Poplar 380 65%

MAINTENANCE

Servicing

We recommend that the stove should have a comprehensive servicing

at least once every two years. Servicing should include the following:

• Lubricate hinges using copper grease

• Check gaskets. Replace any that are broken or weak.

• Check combustion chamber door and riddling grate

• Check combustion chamber lining and baffle plates.

The stove must be serviced by a qualified fitter. Use only orignal

spare parts.

Maintaining your wood-burning stove

Apart from regular chimney sweeping, your wood-burning stove does

not require any regular maintenance. However, we recommend servi-

cing at least once every two years

Use only original replacement parts for maintenance and repairs of

your stove.

Note! Make sure the wood-burning stove is cold before starting

maintenance or repair work.

Coated surfaces

Clean your wood-burning stove by dusting with a dry, lint-free cloth.

If the topcoat is damaged, you can purchase a repair spray from your

authorised Scan dealer. As slight differences in colour are possible,

spray a larger area to achieve a natural transition for best results.

For best results, apply repair spray when the wood-burning stove is

hand-hot.

Cleaning the glass

Our wood-burning stoves are designed to prevent serious soot build

up on the glass. The best way to achieve this is to make sure you have

a sufficient combustion air supply. It is also important to use dry

wood, and have a correctly dimensioned chimney.

Even if you follow all of our instructions, a slight film of soot can build

up on the glass. You can easily remove this build up by cleaning with a

dry cloth and glass cleaner. Please note that the glass cleaner is not

to get into contact with the gaskets, as this can discolour the glass

permanently.

Combustion chamber lining

Slight cracks can appear in the combustion chamber lining due to

moisture, or to the heating/cooling process. These cracks have no

influence on the heating performance or lifetime of your stove.

However, if the lining starts to crumble, you must replace it. The com-

bustion chamber lining is not covered by the warranty.

Gaskets

All wood-burning stoves have gaskets made of ceramic material fitted

to the stove, the doors, and/or the glass. These gaskets are subject to

wear and tear, and must be replaced when necessary.

Chimney sweeping and cleaning your

wood-burning stove

Follow national and local chimney sweeping regulations. We

recommend having the wood-burning stove cleaned regularly by the

chimney sweep.

Before starting to clean your wood-burning stove, and sweep the flue

pipe, we recommend first removing the baffle plates.

Checking the stove

Scan A/S recommends that you check your stove thoroughly after

sweeping/cleaning. Check all visible surfaces for cracks. Check that

all joints are tight and that the seals sit correctly. Worn or deformed

seals should be replaced.

Service

Baffle plates and combustion chamber liningg

Be very careful when removing the baffle plates from the stove.

Lift the burn chamber side plates free from the bottom stones and

take them out. Please note that the sides support the rear plates and

that these may fall over, when the sides are taken out.

Take out the rear plates.

TROUBLESHOOTING

Smoke escaping

• Damp wood

• Chimney not drawing properly

• Chimney is not properly dimensioned for the stove

• Check if the smoke gas pipe/chimney are blocked

• Is the chimney the right height for its surroundings?

• At rear outlet, check that the flue pipe does not obstruct the

chimney draught

• Vacuum in room

• The door is opened before the embers have burned down

sufficiently

Wood burning too quickly

• Incorrect secondary/primary airflow setting

• The baffle plates is incorrectly mounted or missing

• Inferior firewood (waste wood, pallets etc.)

• Chimney too large

Soot build-up on glass

• Incorrect secondary/primary airflow setting

• Damp wood

• Wood pieces too large on lighting

• Inferior firewood (waste wood, pallets etc.)

• Chimney not drawing sufficiently

• Vacuum in room

Excessive soot build-up in chimney

• Poor burning (more air required)

• Damp wood

The surface of the stove is turning grey

• Overheating (see instructions for heating)

Poor heating performance of stove

• Damp wood

• Not enough wood

• Inferior wood quality with low fuel value

• Baffle plates are not fitted correctly

Odour coming from stove

• The lacquer on the stove hardens when you use the stove for the

first time; this can cause an odour. Open a window or a door for

ventilation, and make sure the stove is heated up sufficiently to

avoid odours later.

• When heating up and cooling down, the stove may make some

clicking noises. These are due to the huge temperature diffe-

rences to which the material is exposed and do not indicate any

product defects.

Warranty

All wood-fired Scan products are made of high-quality materials and

subject to strict quality controls before leaving the factory. We give a

warranty of 5 years on manufacturing errors or defects.

You must quote your stove‘s product registration number when you

The warranty covers all parts which in the opinion of Scan A/S require

repair or replacement due to manufacturing or construction error

The warranty applies to the original purchaser of the product only,

and is not transferable (except on prior sale).

The warranty covers only damage caused by manufacturing or con-

struction errors.

The following parts are not covered by the war-

ranty

• Wear and tear parts, such as the combustion chamber liners,

baffle plates, riddling grate, glass, tiles, and seals (except for

defects which were present on delivery).

• Defects caused by external chemical and physical influences

during transportation, storage and assembly, or at a later time.

• Soot build-up caused by poor chimney draught, damp wood, or

improper use.

• Costs of additional heating in connection with a repair.

• Transport costs.

• Costs for setting up, removing the wood stove.

This warranty is void

• In case of incorrect installation (the installer is responsible

for observing and complying with legal requirements and local

bylaws, along with this Assembly- and Instructionsmanual for

the wood-burning stove and accessories).

• In case of improper use, and/or use of prohibited fuels, non-

original spares (see this Assembly- and instructions manual).

• If the product registration number of the stove has been remo-

ved or damaged.

• In case of repairs that do not comply with our instructions or

instructions by an authorised Scan dealer.

• In case of any manipulation of the original state of this Scan

product or its accessories.

• This warranty is only valid in the country to which this Scan pro-

duct was originally supplied.

Always use original replacement parts, or parts recommended by the

manufacturer.

TROUBLESHOOTING

DEFRA

Smoke Control Area air supply requirements

The M5x6 screw is fitted to ensure that the stove

receives sufficient air to meet Defra's requirements.

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:

EMNE:

C:\Working Folder\Designs\Scan 1001\91001048.idw

91001048

Engelsk krav til luftspjæld

09-11-12

Scan 1001

VÆGT:

AREAL:

N/A

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:

EMNE:

C:\Working Folder\Designs\Scan 1001\91001048.idw

91001048

Engelsk krav til luftspjæld

09-11-12

Scan 1001

VÆGT:

AREAL:

N/A

Screw M5x6

Refuelling on to a low fire bed

If there is insufficient burning material in the firebed to light a new

fuel charge, excessive smoke emission can occur. Refuelling must

be carried out onto a sufficient quantity of glowing embers and ash

that the new fuel charge will ignite in a reasonable period. If there

are too few embers in the fire bed, add suitable kindling to prevent

excessive smoke

Fuel overloading

The maximum amount of fuel specified in this manual should not be

exceeded, overloading can cause excess smoke.

Operation with door left open

Operation with the door open can cause excess smoke. The appli-

ance must not be operated with the appliance door left open except

as directed in the instructions.

Dampers left open

Operation with the air controls or appliance dampers open can

cause excess smoke. The appliance must not be operated with air

controls, appliance dampers or door left open except as directed in

the instructions.

The Clean Air Act 1993 and Smoke Control Areas

Under the Clean Air Act local authorities may declare the whole or

part of the district of the authority to be a smoke control area. It

is an offence to emit smoke from a chimney of a building, from a

furnace or from any fixed boiler if located in a designated smoke

control area. It is also an offence to acquire an "unauthorised fuel"

for use within a smoke control area unless it is used in an "exempt"

appliance ("exempted" from the controls which generally apply in the

smoke control area).

In England appliances are exempted by publication on a list by the

Secretary of State in accordance with changes made to sections 20

and 21 of the Clean Air Act 1993 by section 15 of the Deregulation

Act 2015. Similarly in Scotland appliances are exempted by pub-

lication on a list by Scottish Ministers under section 50 of the

Regulatory Reform (Scotland) Act 2014.

In Wales and Northern Ireland these are authorised by regulations

made by Welsh Ministers and by the Department of the Environment

respectively.

Further information on the requirements of the Clean Air Act can be

found here: https://www.gov.uk/smoke-control-area-rules

Your local authority is responsible for implementing the Clean Air

Act 1993 including designation and supervision of smoke control

areas and you can contact them for details of Clean Air Act require-

ments”

The Scan 1010 has been recommended as suitable for use in smoke

control areas when burning wood logs with a modification to thery

air valve so that it will not close beyond the 40% open position.

Important!

Please see installing the screw for secondary air

control with open position.

MAINTENANCE

14.02.2018

Version:

GB 91010 500

Scan A/S - DK-5492 Vissenbjerg

SCAN 1010 Series Assembly And Instruction Manual

Marca: SCAN

Modelo: 1010 Series

Categoría: Estufas

Tipo: Assembly And Instruction Manual

Descargar PDF

informe

en otros idiomas

English: SCAN 1010 Series

SCAN 1010 Series Assembly And Instruction Manual

SCAN 1010 Series Assembly And Instruction Manual

en otros idiomas

Artículos relacionados

Otros documentos