Stock no. 28840, Tradesman Vise Model 1745XC
Stock no. 28841, Tradesman Vise Model 1755XC
Stock no. 28842, Tradesman Vise Model 1765XC
Replacement parts
Stock no. 28840 28841 28842
Model no. 1745XC 1755XC 1765XC
ITEM DESCRIPTION QTY. PART NO.
Stationary Jaw casting # reference 111803XC 111813XC 111823XC
1
Spindle Assembly (includes #1a,1b,2,3)
1 2900000XC 2900150XC 2900330XC
1a Spindle 1 2900001XC 2900151XC 2900331XC
1b Tommy Bar, with rubber rings
1 2900002XC 2900152XC 2900332XC
2
Spindle Retainer with 3 screws and #3
1 2904000 2904000 2904010
3
Thrust Washer
1 Not available separately
4
Set of Jaw Inserts with 4 screws
1 set 2908060XC 2908070XC 2908080XC
5
Set of Pipe Jaw Inserts with 2 screws
1 set 2904200XC 2904200XC 2904200XC
7
Casing Nut with 2 pins
1 2900220AXC 2900240AXC 2900340AXC
8
Lock Nut and Bolt Assemblies (set of 2)
1 set 2905190 2905200 2905200
9
Locking Pads (set of 2)
1 set 9040010 9040020 9040020
10
Outer Ring only
1 1011990XC 1011980XC 1011980XC
11
Swivel Base Assembly (includes #8,9,10)
1 2900230XC 2905790XC 2905790XC
To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model
Number and Serial Number of your tool available when you call will allow us to serve you quickly and accurately. Some parts are shown for
reference only, and may not be available individually.
Specifications
Stock no. 28840 28841 28842
Model no. 1745XC 1755XC 1765XC
Jaw width 4-1/2 in. (114 mm) 5-1/2 in. (140 mm) 6-1/2 in. (165 mm)
Open capacity, maximum1 3-1/2 in. (90.5 mm) 5 in. (127.5 mm) 6 in. (151.5 mm)
Throat depth 3-1/4 in. (82.6 mm) 3-3/4 in. (95.3 mm) 4 in. (101.6 mm)
Pipe jaw capacity 1/4 – 2-1/2 in. (6.4 – 63.5 mm) 1/4 – 3 in. (6.4 – 76.2 mm) 1/4 – 3-1/2 in. (6.4 – 89 mm)
Shipping weight 42 lbs. (19 kg) 51.5 lbs. (23 kg) 71 lbs. (32 kg)
1 based on lead screw engagement with half of nut thread length
WILTON
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-28840
Ph.: 800-274-6848 Edition 2 09/2019
www.wiltontools.com Copyright © 2019 WILTON, a Division of JPW Industries, Inc.
Note: See reverse side for important safety instructions.
IMPORTANT SAFETY INSTRUCTIONS
Misuse of vise can cause serious injury to eyes, hands, limbs, etc.
To ensure safety, vise must be set up and used properly.
Before setting up and using, read, understand, and follow all instructions as
outlined below.
When setting up vise:
Use proper size bolts, nuts, lock and flat washers, in all base mounting
Holes. Never weld base of vise to any metal object.
Only hand-tighten swivel base lock down nuts at the sides of the vise.
Never use a pipe extension to tighten lock nut handles; this can cause the
handles to bend and overstress the lock down bolts.
Make sure the bench top to which the vise is mounted is properly secured.
When using vise:
Always use vise of proper size and capacity to hold work object.
Never use a hammer, pipe extension or cheater bar on spindle handle of
vise.
Never unscrew moveable jaw beyond the maximum specified opening of
the vise.
Never use vise as a press for assembly or disassembly of objects.
Always wear eye and face protection when striking vise-held objects or
when using power tools with a vise.
NOTE: The spindle handle (“tommy bar”) has been engineered to bend if
excessive clamping pressure is applied, to prevent potential damage to
vise.
CONSIGNES DE SECURITE
IMPORTANTES
Une utilisation incorrecte, de l’etau peut entrainer des blessures graves aux
yeux aux mains et a d’autres parties du corps.
Pour guarantir la securite, lÉtau’doit installe et utilise corrÉctement.
Avant installation et utilisation-lire, veiller a bien comprendre et suivre
toutes les instructions telles qu’elles sont donnees de chaque cote de cette
etiquette.
Installation de l’etau:
Pour bloquer la base de l’etau, Útiliser des ecrous, boulons et rondelles de
la bonne taille dans tous les trous de fixation. ne jamais souder la base de
l’etau a Ún objet metallique quelconque.
Pour un etau a base tournante, ne serrer qu’avec les doigts les poignees
des contre-ecrous sur les cotes de l’etau.
Ne jamais utiliser une rallonge pour serrer les poignees des contre-ecrous-
cela pourrait tordre les poignees.
Assurez-vous que l'établi sur lequel est monté l'étau est correctement fixé.
Utilisation de l'étau:
Toujours utiliser un étau de taille et de capacité appropriées pour tenir
l’objet de travail.
Ne jamais utiliser un marteau, une rallonge ni tout autre outil permettant de
faire levier sur la poingee de l’etau.
Ne jamais devisser le mors au-dela de l’ouverture maximum specifiee de
l’etau.
Le jamais utiliser l’etau pour enfoncer un objet dans un autre ou l’en faire
sortir.
Toujours porter des lunettes et un masque de protection pour frapper sur
un object ou utiliser un outillage electrÍque avec un etau.
REMARQUE: La poignée de la broche («barre de serrage») a été conçue
pour se plier si une pression de serrage excessive est appliquée, afin
d'éviter tout dommage potentiel à l'étau.
INSTRUCCIONES DE SEGURIDAD
IMPORTANTES
El uso indebido del tornillo de banco puede causar lesiones graves en los
ojos, en las manos y en otras partes del cuerpo.
Para asegurar la seguridad, el tornillo de banco debe configurarse y
utilizarse de forma debida.
Antes de configurar y usar-lea, entienda y siga todas las instrucciones
indicadas en ambos lados de la etiqueta.
Al configurar el tornillo de banco:
Para sujetar la base del tornillo de banco, use tuercas, pernos y arandelas
de presion del tamano adecuado en todos los agujeros de montaje. No
suelde nunca la base del tornillo de banco a ningun objeto de metal.
Para el tornillo de banco de base giratoria, apriete solamente a mano las
palancas de las contratuercas en los lados del tornillo de banco.
No use nunca un tubo de extension para apretar las palancas en las
contratuercas esto puede hacier que doblen las palancas.
Asegúrese de que la parte superior del banco donde está montado el
tornillo de banco esté bien asegurada.
Al usar el tornillo de banco:
Use siempre un tornillo de banco del tamano y de la capacidad adecuados
para sujetar el objeto de trabajo.
No use nunca un martillo, un tubo de extension o un Álargador en la
palanca del uso del tornillo de banco.
No desatornille nunca la mordaza movil mas alla de la’abertura
especificada maxima del tornillo de banco.
No use nunca el tornillo de banco para encajar un objeto en otro objeto o
desprenderlo de otro objeto.
Lleve siempre protectores de los ojos y la cara al golpear o usar
herramientas as con un tornillo de banco.
NOTA: El mango husillo (“bar Tommy”) ha sido diseñado para doblarse si
se aplica una presión de apriete excesivo, para evitar el daño potencial a
tornillo de banco.
The Wilton® lifetime warranty is for the product’s lifetime with no end date. This warranty covers manufacturer’s defect only and does not
cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair, alterations or
lack of maintenance. For more information, please visit wiltontools.com.
How to Get Technical Support
Please contact Technical Service by calling 1-800-274-6846. Please note that you will be asked to provide proof of initial purchase
when calling. If a product requires further inspection, the Technical Service representative will explain and assist with any additional action needed. Wilton has
Authorized Service Centers located throughout the United States. For the name of an Authorized Service Center in your area call 1-800-274-6846 or use the
Service Center Locator on the Wilton website.
Wilton sells through distributors only. The specifications listed in Wilton printed materials and on official Wilton branded website are given as general information
and are not binding. Wilton reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they
may deem necessary for any reason whatsoever.
NOTE: Wilton is a division of JPW Industries, Inc. References in this document to Wilton also apply to JPW Industries, Inc., or any of its successors in interest
to the Wilton brand.
WARNING: This product can expose you to chemicals including
lead which is known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information go to http://
www.p65warnings.ca.gov.
AVERTISSEMENT: Ce produit peut vous exposer à des produits
chimiques, y compris le plomb qui est connu par l'État de Californie
pour causer le cancer et des malformations congénitales ou d'autres
problèmes de reproduction. Pour plus d'informations, visitez
http://www.p65warnin
g
s.ca.
g
ov.
ADVERTENCIA: Este producto puede exponerlo a productos
químicos, incluido de plomo, que en el estado de California se conoce
como causantes de cáncer y defectos de nacimiento u otros daños
reproductivos. Para obtener más información, vaya a http://www.
p65warnings.ca.gov.
#28840 Model 1745XC Tradesman XC Vise
Mounting Template
Drill four (4) 9/16”diameter holes. Mount vise with four (4) 1/2”
diameter cap bolts, 2 inches longer than benchtop thickness.
Use minimum Grade 5 bolts. Secure with flat washers and nuts.
Align dashed line with edge of workbench. Tape paper in place
and transfer bolt hole centers to benchtop with a center punch.
Make sure underside of bolt hole locations is clear of legs,
brackets, drawers, etc.
1/8 INCH
FOLD LINE
⚠WARNING: Mounting Template for Reference Only
For exact mounting dimensions, please refer to the Bullet
Bench Vise Mounting Dimensions document included with
the product and found online at wiltontools.com.
#28841 Model 1755XC Tradesman XC Vise
#28842 Model 1765XC Tradesman XC Vise
Mounting Template
Drill four (4) 11/16”diameter holes. Mount vise with four (4) 5/8”
diameter cap bolts, 2 inches longer than benchtop thickness.
Use minimum Grade 5 bolts. Secure with flat washers and nuts.
Align dashed line with edge of workbench. Tape paper in place
and transfer bolt hole centers to benchtop with a center punch.
Make sure underside of bolt hole locations is clear of legs,
brackets, drawers, etc.
1/8 INCH
FOLD LINE
⚠WARNING: Mounting Template for Reference Only
For exact mounting dimensions, please refer to the Bullet
Bench Vise Mounting Dimensions document included with
the product and found online at wiltontools.com.
Stock No. Model Base Outer
Ring Part No.
Dimension A
(in.)
Dimension B
(in.)
Dimension C
(in.)
Dimension D
(in.)
Bolt Circle
Diameter (in.)
Bolt Hole
Diameter (in.)
Mounting Bolt
Diameter (in.)
28825 C0 1011990 2 3/16” 2 7/8” 3 1/16” 2 7/16” 7 1/2” 9/16” 1/2”
28826 C1 1011980 2 9/16” 3 5/16” 3 9/16” 2 13/16” 8 3/4” 11/16” 5/8”
28827 C2 1010840 2 13/16” 3 3/4” 4 ” 3 1/8” 9 3/4” 11/16” 5/8”
28828 C3 1011080 3 1/2” 4 3/8” 4 1/2” 3 5/8” 11 3/8” 11/16” 5/8”
28830 300S 1012010 1 7/8” 2 7/16” 2 9/16” 2 1/16” 6 3/8” 7/16” 3/8”
28831 400S 1011980 2 9/16” 3 5/16” 3 9/16” 2 13/16” 8 3/4” 11/16” 5/8”
28832 500S 1011980 2 9/16” 3 5/16” 3 9/16” 2 13/16” 8 3/4” 11/16” 5/8”
28833 600S 1010840 2 13/16” 3 3/4” 4 ” 3 1/8” 9 3/4” 11/16” 5/8”
28834 800S 1011080 3 1/2” 4 3/8” 4 1/2” 3 5/8” 11 3/8” 11/16” 5/8”
28840 1745XC 1011990XC 2 3/16” 2 7/8” 3 1/16” 2 7/16” 7 1/2” 9/16” 1/2”
28841 1755XC 1011980XC 2 9/16” 3 5/16” 3 9/16” 2 13/16” 8 3/4” 11/16” 5/8”
28842 1765XC 1011980XC 2 9/16” 3 5/16” 3 9/16” 2 13/16” 8 3/4” 11/16” 5/8”
28843 1780XC 1010840XC 2 13/16” 3 3/4” 4 ” 3 1/8” 9 3/4” 11/16” 5/8”
28805 1745 1011990 2 3/16” 2 7/8” 3 1/16” 2 7/16” 7 1/2” 9/16” 1/2”
28806 1755 1011980 2 9/16” 3 5/16” 3 9/16” 2 13/16” 8 3/4” 11/16” 5/8”
28807 1765 1011980 2 9/16” 3 5/16” 3 9/16” 2 13/16” 8 3/4” 11/16” 5/8”
28808 1780A 1010840 2 13/16” 3 3/4” 4 ” 3 1/8” 9 3/4” 11/16” 5/8”
Tradesman
XC
Combo Pipe
& Bench
MachinistTradesman
Bullet Bench Vise Mounting Dimensions
-
1
-
2
-
3
-
4
-
5
En otros idiomas
- français: Wilton 28840 Manuel utilisateur
- English: Wilton 28840 User manual
Documentos relacionados
-
Wilton 28827 Manual de usuario
-
-
-
-
-
-
-
-
Wilton 11128 Manual de usuario
-