#28834, 8-inch Swivel Base Machinist Vise (model 800S)
Replacement parts
Item Part No. Description
1 2907050 Spindle Assembly Complete
2 2904540 Spindle Retainer (with 3 screws and #3)
3 --- Thrust Washer (not available separately)
4 2904940 Serrated Jaw Inserts with 4 screws
5 2904550 End Piece Assembly Complete, with 2 pins
6 2900090 Casing Nut with 2 pins
7 2905230 Lock Nut Assemblies
8 1011070 Inner Ring with Dowel Pin
9 1011080 Outer Ring only
10 2904580 Swivel Base Assembly Complete (includes #7,8,9)
To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model
Number and Serial Number of your tool available when you call will allow us to serve you quickly and accurately. Some parts are shown for
reference only, and may not be available individually.
WILTON
427 New Sanford Road
LaVergne, Tennessee 37086 M-28834
Ph.: 800-274-6848 Edition 1 09/2018
www.wiltontools.com Copyright © 2018 WILTON, a Division of JPW Industries, Inc.
Note: See reverse side for important safety instructions.
Specifications
Stock no. 28834
Model no. 800S
Jaw width 8 in. (203 mm)
Jaw opening 12 in. (305 mm)
Throat depth 5-13/16 in. (148 mm)
Net weight 238 lbs. (108 kg)
IMPORTANT SAFETY INSTRUCTIONS
• Misuse of vise can cause serious injury to eyes, hands, limbs, etc.
• To ensure safety, vise must be set up and used properly.
• Before setting up and using, read, understand, and follow all instructions
as outlined below.
When setting up vise:
• Use proper size bolts, nuts, lock and flat washers, in all base mounting
Holes. Never weld base of vise to any metal object.
• Only hand-tighten swivel base lock down nuts at the sides of the vise.
• Never use a pipe extension to tighten lock nut handles; this can cause
the handles to bend and overstress the lock down bolts.
• Make sure the bench top to which the vise is mounted is properly
secured.
When using vise:
• Always use vise of proper size and capacity to hold work object.
• Never use a hammer, pipe extension or cheater bar on spindle handle of
vise.
• Never unscrew moveable jaw beyond the maximum specified opening of
the vise.
• Never use vise as a press for assembly or disassembly of objects.
• Always wear eye and face protection when striking vise-held objects or
when using power tools with a vise.
• NOTE: The spindle handle (“tommy bar”) has been engineered to bend if
excessive clamping pressure is applied, to prevent potential damage to
vise.
CONSIGNES DE SECURITE IMPORTANTES
• Une utilisation incorrecte, de l’etau peut entrainer des blessures graves
aux yeux aux mains et a d’autres parties du corps.
• Pour guarantir la securite, lÉtau’doit installe et utilise corrÉctement.
• Avant installation et utilisation-lire, veiller a bien comprendre et suivre
toutes les instructions telles qu’elles sont donnees de chaque cote de
cette etiquette.
Installation de l’etau:
• Pour bloquer la base de l’etau, Útiliser des ecrous, boulons et rondelles
de la bonne taille dans tous les trous de fixation. ne jamais souder la
base de l’etau a Ún objet metallique quelconque.
• Pour un etau a base tournante, ne serrer qu’avec les doigts les poignees
des contre-ecrous sur les cotes de l’etau.
• Ne jamais utiliser une rallonge pour serrer les poignees des contre-
ecrous-cela pourrait tordre les poignees.
• Assurez-vous que l'établi sur lequel est monté l'étau est correctement
fixé.
Utilisation de l'étau:
• Toujours utiliser un étau de taille et de capacité appropriées pour tenir
l’objet de travail.
• Ne jamais utiliser un marteau, une rallonge ni tout autre outil permettant
de faire levier sur la poingee de l’etau.
• Ne jamais devisser le mors au-dela de l’ouverture maximum specifiee de
l’etau.
• Le jamais utiliser l’etau pour enfoncer un objet dans un autre ou l’en faire
sortir.
• Toujours porter des lunettes et un masque de protection pour frapper sur
un object ou utiliser un outillage electrÍque avec un etau.
• REMARQUE: La poignée de la broche («barre de serrage») a été
conçue pour se plier si une pression de serrage excessive est appliquée,
afin d'éviter tout dommage potentiel à l'étau.
INSTRUCCIONES DE SEGURIDAD
IMPORTANTES
• El uso indebido del tornillo de banco puede causar lesiones graves en
los ojos, en las manos y en otras partes del cuerpo.
• Para asegurar la seguridad, el tornillo de banco debe configurarse y
utilizarse de forma debida.
• Antes de configurar y usar-lea, entienda y siga todas las instrucciones
indicadas en ambos lados de la etiqueta.
Al configurar el tornillo de banco:
• Para sujetar la base del tornillo de banco, use tuercas, pernos y
arandelas de presion del tamano adecuado en todos los agujeros de
montaje. No suelde nunca la base del tornillo de banco a ningun objeto
de metal.
• Para el tornillo de banco de base giratoria, apriete solamente a mano las
palancas de las contratuercas en los lados del tornillo de banco.
• No use nunca un tubo de extension para apretar las palancas en las
contratuercas esto puede hacier que doblen las palancas.
• Asegúrese de que la parte superior del banco donde está montado el
tornillo de banco esté bien asegurada.
Al usar el tornillo de banco:
• Use siempre un tornillo de banco del tamano y de la capacidad
adecuados para sujetar el objeto de trabajo.
• No use nunca un martillo, un tubo de extension o un Álargador en la
palanca del uso del tornillo de banco.
• No desatornille nunca la mordaza movil mas alla de la’abertura
especificada maxima del tornillo de banco.
• No use nunca el tornillo de banco para encajar un objeto en otro objeto o
desprenderlo de otro objeto.
• Lleve siempre protectores de los ojos y la cara al golpear o usar
herramientas as con un tornillo de banco.
• NOTA: El mango husillo (“bar Tommy”) ha sido diseñado para doblarse
si se aplica una presión de apriete excesivo, para evitar el daño
potencial a tornillo de banco.
The Wilton® lifetime warranty is for the product’s lifetime with no end date. This warranty covers manufacturer’s defect only and does not
cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair, alterations or lack
of maintenance. For more information, please visit wiltontools.com.
How to Get Technical Support
Please contact Technical Service by calling 1-800-274-6846. Please note that you will be asked to provide proof of initial purchase
when calling. If a product requires further inspection, the Technical Service representative will explain and assist with any additional action needed. Wilton has
Authorized Service Centers located throughout the United States. For the name of an Authorized Service Center in your area call 1-800-274-6846 or use the Service
Center Locator on the Wilton website.
Wilton sells through distributors only. The specifications listed in Wilton printed materials and on official Wilton branded website are given as general information and
are not binding. Wilton reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem
necessary for any reason whatsoever.
NOTE: Wilton is a division of JPW Industries, Inc. References in this document to Wilton also apply to JPW Industries, Inc., or any of its successors in interest to the
Wilton brand.
WARNING: This product can expose you to chemicals including
titanium dioxide which is known to the State of California to cause
cancer. For more information go to http:// www.p65warnings.ca.gov.
AVERTISSEMENT: Ce produit peut vous exposer à des produits
chimiques, y compris le dioxyde de titane qui est connu par l'État de
Californie pour causer le cancer. Pour plus d'informations, visitez
htt
p
://www.
p
65warnin
g
s.ca.
g
ov.
ADVERTENCIA: Este producto puede exponerlo a productos
químicos, incluido de dióxido de titanio, que en el estado de California
se conoce como causantes de cáncer. Para obtener más información,
va
y
a a htt
p
://www.
p
65warnin
g
s.ca.
g
ov.
Stock No. Model Base Outer
Ring Part No.
Dimension A
(in.)
Dimension B
(in.)
Dimension C
(in.)
Dimension D
(in.)
Bolt Circle
Diameter (in.)
Bolt Hole
Diameter (in.)
Mounting Bolt
Diameter (in.)
28825 C0 1011990
2 3/16” 2 7/8” 3 1/16” 2 7/16” 7 1/2” 9/16” 1/2”
28826 C1 1011980
2 9/16” 3 5/16” 3 9/16” 2 13/16” 8 3/4” 11/16” 5/8”
28827 C2 1010840
2 13/16” 3 6/8” 4 ” 3 1/8” 9 3/4” 11/16” 5/8”
28828 C3 1011080
3 1/2” 4 3/8” 4 1/2” 3 5/8” 11 3/8” 11/16” 5/8”
28830 300S 1012010
1 7/8” 2 7/16” 2 9/16” 2 1/16” 6 3/8” 7/16” 3/8”
28831 400S 1011980
2 9/16” 3 5/16” 3 9/16” 2 13/16” 8 3/4” 11/16” 5/8”
28832 500S 1011980
2 9/16” 3 5/16” 3 9/16” 2 13/16” 8 3/4” 11/16” 5/8”
28833 600S 1010840
2 13/16” 3 3/4” 4 ” 3 1/8” 9 3/4” 11/16” 5/8”
28834 800S 1011080
3 1/2” 4 3/8” 4 1/2” 3 5/8” 11 3/8” 11/16” 5/8”
28840 1745XC 1011990XC
2 3/16” 2 7/8” 3 1/16” 2 7/16” 7 1/2” 9/16” 1/2”
28841 1755XC 1011980XC
2 9/16” 3 5/16” 3 9/16” 2 13/16” 8 3/4” 11/16” 5/8”
28842 1765XC 1011980XC
2 9/16” 3 5/16” 3 9/16” 2 13/16” 8 3/4” 11/16” 5/8”
28843 1780XC 1010840XC
2 13/16” 3 3/4” 4 ” 3 1/8” 9 3/4” 11/16” 5/8”
28805 1745 1011990
2 3/16” 2 7/8” 3 1/16” 2 7/16” 7 1/2” 9/16” 1/2”
28806 1755 1011980
2 9/16” 3 5/16” 3 9/16” 2 13/16” 8 3/4” 11/16” 5/8”
28807 1765 1011980
2 9/16” 3 5/16” 3 9/16” 2 13/16” 8 3/4” 11/16” 5/8”
28808 1780A 1010840
2 13/16” 3 3/4” 4 ” 3 1/8” 9 3/4” 11/16” 5/8”
Tradesman
XC
Combo Pipe
& Bench
MachinistTradesman
Bullet Bench Vise Mounting Dimensions
-
1
-
2
-
3
en otros idiomas
- français: Wilton 28834 Manuel utilisateur
- English: Wilton 28834 User manual
Artículos relacionados
-
Wilton 28825 Manual de usuario
-
-
-
-
-
-
-
-
-