Fine Decorative Plumbing Since 1935
WESTBRASS
ASME A112.18.1 / CSA B125.1
YOU MAY NEED:
USTED PUEDE NECESITAR:
Screwdriver
El destornillador
Tape measure
Cinta métrica
on screws.
Importante: Use cinta para
plomero en las tornillos.
Pliers: For removal and instal-
lation.
Alicates: Para quitar y insta-
lación.
SILCO
N
E
Silicone Sealant: Use Silicone
sealant under base of strainer.
Sellador de silocón: Si el lava-
manos está desnivelado use
sellador de silicón debajo de la
base del borde.
Tubing Cutter
Cortador de Tubos
Exposed Bathwaste
& Overow
Desbordamiento de baño Dren
del Tirón
Fine Decorative Plumbing Since 1935
WESTBRASS
2429 E. Olympic Blvd.
Los Angeles, CA 90021
REVDWG NO.
DAT E
Sheet 1 of 1
Scale
TITLE
D3261HKBJ
D3261HKBJ
Illusionary Fully Finished Brass Ball Joint
1 to 4 mrohlfs
1-7-2016 A
4A-2F
Finished
332-3/16
Silicone O-Ring
792BJ
6” Tailpiece
(1126171T)
18-1/2”
(1121812171)
9-1/2”
(112912171)
(792RW)
22-1/2”
Maximum
11”
Maximum
(792-C)
(792B-C)
(818-F)
1-1/2”
Dia.
3” Dia.
1-1/2”
D409
1-7/8” - 11-1/2
Coarse Thread
(D3322-2 or
793SOCP-C)
D3322-1
or 79338MOCP
1-7/8” - 11-1/2
NPSM Thread
2-5/8”
3/8” - 16
D398R
3/8” - 16 UNC-2B
Threaded Through
1/4” - 20
UNC-2A
2-7/8”
D98-RING
D980R
D980-CAP
1. Measure and dry t
all connections.
Use Tubing Cutter
to cut tubes as required.
2. Use balljoint to match
top elbow to tub.
3. Place rubber gasket on
overow elbow.
4. Place shoe elbow
under tub, using rubber
washer between bottom
of tub and shoe elbow.
1. Medir y en forma seca todas las
conexiones. Uso del cortador de tubos
para cortar tubos según sea necesario.
2. Utilice rotula para que coincida con
la parte superior del codo de la ba-
ñera.
3. Coloque la junta de goma en el
codo del rebosadero.
4. Coloque el zapato codo bajo bañera
utilizando la arandela de goma entre,
el fondo de la tina y el codo zapato.
Installation Instructions:
Instrucciones de Instalación
Silicone Sealant
Silicone
Silicone Sealant
2429 East Olympic Blvd. • Los Angeles, CA 90021
Finishes:
(01) PVD Polished Brass (26) Polished Chrome (07) Satin Nickel
(12) Oil Rubbed Bronze (50) Powder Coated W (62) Powder Coated Flat Black
CARE & MAINTENANCE
TO CLEAN:
Do not allow your product to come into contact with any cleansers forti-
Soft Scrub, Dawn Liquid Soap, Palmolive or any other combined cleaners
contain certain chemical components that will dissolve and remove the
warm water and mild soap on a soft cloth or sponge. Avoid using any
sponge with a scouring pad to clean your product. It is not necessary to
rub hard to remove spots.
and living, require some care in use.
WARRANTY
a rof detnarraw si stcudorp lla fo ytilanoitcnuf ehT
retaw yna no sevlav csid cimareC .raey one fo doirep
delivery merchandise are warranted for one year. Warran-
ties are guaranteed to the original purchaser only. Product
problems attributable to abuse, misuse, improper instal-
lation, hard water, neglected maintenance or accidental
damage are not covered by this warranty. Modifying the
product in any way voids the warranty. The use of plumb-
er’s putty on our products also voids the warranty. Silicone
sealing compounds should be used instead. No repairs
or replacements will be made under
such circumstances
except at customer’s expense. Liability under warranties
expressed or implied is limited to repair or replacement of
defective goods only. In no event will Westbrass be liable for
incidental or consequential damages (such as labor charges).
This warranty does not cover labor charges, whether based on
breach of express or implied warranty, breach of contract,
negligence or any other legal theory.
TO PROTECT:
An occasional application of Carnauba wax
(without cleaners), like that found in Flitz Fau-
cet Wax, Turtle Wax for Clear Coat Car Finishes
or McGuire’s Premium Wax, will enhance the
Functional Warranty:
Other Westbrass nishes, including living nishes and other electroplated nishes carry no warranty.
WESTBRASS • 2429 E. Olympic Blvd., Los Angeles, CA 90021
(213)-627-8441 • (213) 627-2844 • or[email protected] • www.westbrass.com
5. Place a thin bead of sili-
cone seal for strainer.
6. Screw in strainer through
the tub into shoe elbow.
7. Wipe o any excess
silicone with a clean towel
then thread in stopper.
8. Securely screw overow
cover into top elbow and
thread in overow.
9. Tighten all nuts and ax
Hi-Box ange.
10. Check for leaks.
Silicone seal locations
Lugares de sellado de silicona
Tighten using Pliers or a plug
wrench
Apriete utilizando alicates o una
llave de bujías
5. Coloque un cordón delgado de
la junta de silicona para el cola-
dor.
6. Atornille el filtro a través de la
bañera en el codo zapato.
7. Limpie el exceso de silicona con
una toalla limpia luego pase en
tapón.
8. tornillo firmemente la cubierta
de desbordamiento en la parte
superior del codo y el hilo de
desbordamiento.
9. Apretar todos los tornillos y fije
la brida Hi- Box.
10. Compruebe si hay fugas.
-
1
-
2
Westbrass D3261HKBJ-05 Guía de instalación
- Tipo
- Guía de instalación
- Este manual también es adecuado para
en otros idiomas
Artículos relacionados
-
Westbrass D331-26 Guía de instalación
-
Westbrass D503-05 Guía de instalación
-
Westbrass D502-62 Guía de instalación
-
-
Westbrass 792BR Guía de instalación
-
-
Westbrass D324-20 Guía de instalación
-
-
Westbrass D98RK-07 Guía de instalación
-
