Wicked Audio WI-BT150 El manual del propietario

Tipo
El manual del propietario
SPECS
DRIVER 40 mm Neodymium
SENSITIVITY 103 dB
FREQUENCY 20-20,000 Hz
IMPEDANCE 32 Ohms
CORD LENGTH 4 ft / 1.2 m
GARANTÍA DE POR VIDA
Guarde su recibo para obtener servicio de garantía.
Hora de salida www.wickedaudio.com para más detalles.
Over exposure to excessive sound levels can damage your ears resulting in
permanent noise-induced hearing loss (NIHL). Please use the following guidelines
established by the Occupational Safety Health Administration (OSHA) on maximum
time exposure to sound pressure levels before hearing damage occurs.
PRECAUTIONS
90 dB SPL at 8 hours, 95 dB SPL at 4 hours, 100 dB SPL at 2 hours, 105 dB SPL at 1 hours, 110
dB SPL at 30 min, 115 dB SPL at 15 min, 120 dB SPL: Avoid as damage may occur
90 dB SPL a 8 horas, 95 dB SPL a 4 horas 100 dB SPL a 2 horas, 105 dB SPL a 1 horas, 110 dB
SPL a 30 minuto, 115 dB SPL a 15 minuto, 120 dB SPL: Evite que se puede producir daños
SAFE USE & HAZARD WARNINGS
ADVERTENCIA
ESCUCHA DEL AUDIO NIVELES EXCESIVOS DE VOLUMEN PUEDE
CAUSAR DAÑOS PERMANENTES AUDIENCIA. SE USE COMO VOLUMEN
MÁS BAJO POSIBLE.
USO SEGURO DE PELIGROS Y ADVERTENCIAS
Durante la exposición a niveles excesivos de ruido puede dañar los oídos resultando
en ruido permanente pérdida de audición inducida (PAIR). Por favor, use las
siguientes pautas establecidas por la Administración de Seguridad de Salud
Ocupacional (OSHA) de tiempo máximo que los niveles de presión de sonido antes de
que se produce una lesión auditiva.
LISTENING TO AUDIO AT EXCESSIVE VOLUMES CAN CAUSE PERMANENT
HEARING DAMAGE. USE AS LOW A VOLUME AS POSSIBLE.
1 Product does not turn on:
• 1a – Make sure switch is in the “On” position, LED will turn on
• 1b – If product is in the “On” position, try turning the product
to the “Off” position and switching back to the “On” position
• 1c - Make sure battery is charged. Charge battery for at
least 30 minutes and power on again
2 Your Bluetooth device is unable to search for/locate/pair
with Wicked Audio Bluetooth product:
• 2a - Be sure your Bluetooth device has Bluetooth
capabilities turned on/activated
• 2b - Be sure your Wicked Audio product is in pairing mode
(LED will be ashing Red AND Blue)
• 2c - Delete/Forget/Unpair the Wicked Audio product from
your Bluetooth list on your device or other nearby devices and
search again
• 2d - If still unable to search for/locate/pair with Wicked
Audio Bluetooth product, please restart your Bluetooth device
and the Wicked Audio product and search again
3 Disconnected after your Bluetooth device successfully
connected/paired with your Wicked Audio product:
• 3a - The Bluetooth signal has been blocked with an
obstruction/exceeded Bluetooth range between your Bluetooth
device and the Wicked Audio product OR the “Play/Pause/An-
swer/Hang up” button was held down for too long and
disconnected. You will need to manually select “Wicked Endo” in
your Bluetooth list on your device to successfully pair your Endo
to your device.
• 3b - Check to see if the battery is at low power, charge if
needed
TROUBLESHOOTING CONTINUED...TROUBLESHOOTING
Developed in Utah, U.S.A.
Made in China
WICKEDAUDIO.COM
WICKED AUDIO, INC.
875 W 325 N
Lindon, UT 84042
BLUETOOTH
VERSION 4.1
RANGE 32 Feet/10 Meters
BATTERY LIFE 8+ Hours
CHARGE TIME 1 Hour
LIMITED ONE YEAR WARRANTY
Keep your receipt to obtain warranty service.
Go to www.wickedaudio.com for more details.
FCC Statement This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions (1)this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation
Limitation of Liability Any Changes or modications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.The
device has been evaluated to meet general RF exposure requirement. The device can be
used in portable exposure condition without restriction.
In no event, under any cause of action of theory of liability, shall Wicked Audio Inc., its
distributors or suppliers be liable to you or any third party for indirect, incidental,
consequential, special, exemplary or punitive damages, of any and all nature whatsoever,
arising out of use of or inability to use a product. This includes without limitation,
property damage, loss of value of the product or any third party products that are used in
or with the Wicked Audio products, even if the Wicked Audio product has been advised of
the possibility of such damages that one may encounter. Without limiting the foregoing,
you understand and agree that Wicked Audio has no liability for any damages or
destruction to the consumer electronics devices or other personal property that are
contained in inside or outside the Wicked Audio products. This includes without limitation,
laptops, cellular phones, or other hand-held devices, or any loss of data contained on the
foreign device. Notwithstanding any damages that you might incur for general damages in
contract, tort (including negligence) or otherwise), the entire aggregate liability of Wicked
Audio and any of its distributors and/or suppliers shall be limited to the amount actually
paid by you for the Wicked Audio product giving rise to liability. Some states and/or
jurisdictions do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you. The limitations of
liability set forth above shall apply to the maximum extent permitted under applicable law.
FIRST TIME USE
1
2
3
4
Make sure that the headset is charged, your phone turned on,
with the Bluetooth feature enabled.
Turn on the Wicked Endo and the LED will ash red and blue.
Your mobile phone should detect “Wicked Endo”
Select “Wicked Endo” to pair and once succesfully paired, the
LED will slowly ash blue.
FUNCTIONS
LINE IN OPTION
When you’d like to use the headset as normal wired headphones, plug the aux cord into the
“line in” port and the Bluetooth feature will shut off. This is handy for listening to movies on
the plane, if you don’t want to drain the battery, or if the battery is dead.
After using the line in option, the Endo might need to be turned off and
on again to return to Bluetooth pairing mode. It is recommended
to turn off the Endo when using the aux cord as the battery
will still drain if the Endo is not in the off position.
(Note: When the line in port is being used, the button
functions cannot be used.
The mic will still work with calls, but all functions must
be controlled from the device.)
PLAY/PAUSE/ANSWER CALL/HANG UP
DISCONNECT & RETURN TO PAIRING MODE
NEXT TRACK
PREVIOUS TRACK
VOLUME UP
VOLUME DOWN
1 PRESS
LONG PRESS
1 PRESS
1 PRESS
LONG PRESS
LONG PRESS
VOLUME UP/
NEXT TRACK
VOLUME DOWN/
PREVIOUS TRACK
CHARGING PORT
LINE IN
PLAY/PAUSE/CALL
ON/OFF
LED
MICROPHONE
4 Unable to connect/pair your desired Bluetooth device with
your Wicked Audio product after connecting your Wicked
Audio product with multiple Bluetooth devices:
• 4a - Your Wicked Audio product will attempt to
connect/pair with last Bluetooth device it paired with
• 4b - Turn off Bluetooth capabilities on other Bluetooth
devices in your vicinity that were recently paired to your Wicked
Audio product. This will allow your desired Bluetooth product to
connect with your Wicked Audio product.
• 4c - If still unable to pair with Wicked Audio Bluetooth
product, please restart your Bluetooth device and the Wicked
Audio product and search again.
5 No sound when talking with someone on the phone using
mic on Wicked Audio product
• 5a - Make sure the Wicked Audio product is successfully
paired with your Bluetooth device
• 5b - Increase the volume of your Bluetooth device and/or
Wicked Audio product
6 No sound when playing music
• 6a - Increase the volume of your Bluetooth device and/or
Wicked Audio product
• 6b - Make sure the Wicked Audio is successfully paired with
your Bluetooth device
7 Unable to charge
• 7a - Wicked Audio product will have a solid Red LED when
charging and the LED will turn off when fully charged.
• 7b - Make sure the USB cable is connecting well with
charger and the micro USB cable is connecting well with your
Bluetooth device
LINE IN
OFF
ON
  • Page 1 1

Wicked Audio WI-BT150 El manual del propietario

Tipo
El manual del propietario

en otros idiomas