Kenmore 580.74083 El manual del propietario

Categoría
Acondicionadores de aire de sistema dividido
Tipo
El manual del propietario
Owner's Manual
Manual del Propietario
®
ROOM AIR CONDITIONER
ACONDICIONADOR DE AIRE DE VENTANA
Model, Modelo 580.74083
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.sears.com
TABLE OF CONTENTS ........................2
WARRANTY ..............................................2
SAFETY .....................................................3
Important Safety Instructions ...................... 3
ELECTRICAL REQUIREMENTS .......4
INSTALLATION ........................................5
Installation Requirements ......................... 5
installation ................................................ 6
How to Install ............................................ 6
Removal from Window ................................. 7
OPERATION .............................................8
How and Why ........................................... 8
Normal Sounds ........................................ 8
Capacity and Running Time ..................... 8
Features ................................................. 9
Using the Air Conditioner ....................... 9
Display .................................................... 10
Remote Control ...................................... 11
MAINTENANCE .....................................12
Air Filter Cleaning ................................... 12
Air Conditioner Cleaning ........................ 12
How to Remove the Front Grille .................. 12
How to Replace the Front Grille .................. 12
TROUBLESHOOTING .........................13
Before Calling for Service ...................... 13
ESPANOL ................................................15
MASTER PROTECTION
AGREEMENTS ......................................31
SERVICE NUMBERS ............ Back Cover
FULL ONE YEAR WARRANTY ON
ROOM AIR CONDITIONER
For one year from the date of purchase, when this
air conditioner is operated and maintained for
normal room cooling according to the instructions
in this owner's manual, Sears will repair this air
conditioner, free of charge, if defective in material or
workmanship.
FULL FIVE-YEAR WARRANTY ON
SEALED REFRIGERATION SYSTEM
For five years from the date of purchase, when this
air conditioner is operated and maintained for
normal room cooling according to the instructions
in this owner's manual, Sears will repair the sealed
refrigeration system (consisting of refrigerant,
connecting tubing, and compressor), free of charge,
if defective in material or workmanship.
WARRANTY SERVICE IS AVAILABLE BY
CONTACTING SEARS SERVICE AT
1-800-4-MY-HOME ®.
Warranty coverage applies only to air conditioners
used for non-commercial, private household
purposes.
This warranty applies only while this product is in
use in the United States.
This warranty gives you specific legal rights, and
you may also have other right which vary from state
to state.
Sears, Roebuck and Co., D/817WA,
Hoffman Estates, IL 60179 U.S.A.
-2-
IMPORTANT SAFETY INSTRUCTIONS
The safety instructions below will tell you how to use your room air conditioner to avoid harm to yourself or
damage to your ROOM AIR CONDITIONER.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance. Read product labels for flammability and
other warnings.
PREVENT ACCIDENTS
To reduce the risk of fire, electrical shock, or injury
to persons when using your air conditioner, follow
basic precautions, including the following:
Be sure the electrical service is adequate for the
model you have chosen.
If the air conditioner is to be installed in a window,
you will probably want to clean both sides of the
glass first. If the window is a triple-track type with a
screen panel included, you may want to remove
the screen completely before installation.
Be sure the air conditioner has been securely and
correctly installed according to the separate
installation instructions provided with this manual.
Save this manual and installation instructions for
possible future use in removing or reinstalling this
unit.
Use gloves when handling the air conditioner.
Be careful to avoid cuts from sharp metal fins on
front and rear coils.
V.t_V_Vl:1;i_ll_[tlELECTRICAL INFORMATION
The complete electrical rating of your new room air
conditioner is stated on the serial plate. Refer to the
rating when checking the electrical requirements.
Be sure the air conditioner is properly grounded.
To minimize shock and fire hazards, proper
grounding is important. The power cord is
equipped with a three-prong grounding plug for
protection against shock hazards.
Your air conditioner must be plugged into in a
properly grounded wall receptacle. If the wall
receptacle you intend to use is not adequately
grounded or protected by a time delay fuse or
circuit breaker, have a qualified electrician install
the proper receptacle.
Do not run air conditioner with a protective
covering. This could result in mechanical damage
within the air conditioner.
Do not use an extension cord or an adapter
plug.
_ Avoid fire hazard or electric shock.
Do not use an extension cord or an adapter plug.
Do not remove any prong from the power cord.
Grounding type
wall receptacl Do not, under any
circumstances, cut,
remove, or bypass
the grounding prong
from this plug.
Power supply cord
with 3-prong _,_,
grounding plug \,
ENERGY SAVING IDEAS
The capacity of the room air conditioner must fit
the room size for efficient and satisfactory
operation.
install the room air conditioner on the shady side
of your home. A window that faces north is best
because it is shaded most of the day.
Do not block air conditioner flow inside with blinds,
curtains, or furniture, or outside with shrubs,
enclosures, or other buildings.
Close the floor and wall registers and the fireplace
damper so cool air does not escape up the
chimney or into the duct work.
Keep blinds and drapes in other windows closed
during the sunniest part of the day.
Clean the air filter as recommended in the
MAINTENANCE section of this manual.
Proper insulation and weather stripping in your
home will help keep warm air out and cool air in.
External house shading with trees, plants or
awnings will help reduce the air conditioner's work
load.
Operate heat producing appliances such as
ranges, washers, dryers, and dishwashers during
the coolest part of the day.
-3-
OBSERVEALL LOCAL CODES AND
ORDINANCES.
DO NOT, UNDER ANY CIRCUMSTANCES,
REMOVE THE POWER SUPPLY CORD
GROUND PRONG.
ELECTRICAL GROUND IS REQUIRED ON
THIS APPLIANCE.
A 115-volt 60 Hz, AC only, 15A fused and
properly grounded electrical supply is required.
A time delay fuse or time delay circuit breaker
is recommended. Use a dedicated circuit,
serving only this appliance.
DO NOT USE AN EXTENSION CORD.
RECOMMENDED GROUNDING METHOD
For your personal safety, this appliance must
be grounded. This appliance has a power
supply cord with a 3-prong grounding plug. To
minimize possible shock hazard, the cord must
be plugged into a mating grounding type wall
receptacle and grounded in accordance with
the National Electrical Code (ANSI/NFPA 70)
latest edition and all local codes and
ordinances. If a mating wall receptacle is not
available, it is the personal responsibility and
obligation of the customer to have a properly
grounded 3-prong wall receptacle installed by a
qualified electrician.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result
in death, fire, or electrical shock.
3-prong _ _ II_'l_"_
grounding /L"--_/'/_ IL',L, 1
0,u0
N Ground
Power _ prong
supply
cord
--3-prong
grounding
type wall
receptacle
-4-
INSTALLATION REQUIREMENTS
Your air conditioner will install into standard double hung
windows with actual clear opening widths of 22 to 36
inches (559mm to 914mm) (FIG. 1).
Lower sash must open sufficiently to allow a clear
vertical opening of 13 inches (331 mm). Side louvers
and the rear of the air conditioner must have clear
air space to allow enough airflow through the
condenser for heat removal. The rear of the unit
must be outdoors, not inside a building or garage.
" Sash
1 22te30"--II
1113"m'n innersitll I _ Window
,,_'÷i'l;><-,_ Offset
si,
_ Exterior
Interior watt "*",,_ i_ FIG. 1
-. .... ÷
ELECTRICAL SERVICE
Check your available electrical service. The power
supply available must be the same as that shown
on the unit nameplate (found on right side of cabinet).
All models are equipped with a 3-prong service plug
to provide proper service and safe positive
grounding. Do not change plug in any way. Do not
use an adapter plug. If your present wall outlet does
not match your plug, call a qualified electrician to
make the necessary corrections.
SAVE CARTON and this OWNER'S MANUAL for
future reference. The carton is the best way to store
unit during winter or when not in use.
To avoid risk of personal injury, propertydamage,
or product damage dueto the weight of this
device and sharp edges that may be exposed:
Air conditioners covered in this manual pose an
excessiveweight hazard. Two or more people
are needed to moveand install the unit.
To prevent injury or strain, use proper lifting and
carrying techniques when moving unit.
Carefully inspect location where air conditioner
will be installed. Be sure itwill support the
weight of the unit over an extended period of
time.
Handle air conditioner with care. Wear
protective gloves whenever lifting or carrying the
unit. AVOID the sharp metalfins of front and
rear coils.
Make sure air conditioner does not fall during
installation.
INSTALLATION HARDWARE
®
ITEM NAME OF PARTS Q'TY
A SHORT SCREW 11
B WOOD SCREW 5
C L BRACKET 3
D FOAM STRIP 1
E FOAM SEAL 1
F SIDE CURTAIN 2
G DRAIN PIPE 1
H SUPPORT BRACKET 1
REQUIREDTOOLS:
Tight Fitting gloves
Standard screwdriver
Phillips screwdriver
Pliers
Sharp knife
3/8-inch open end
wrench or adjustable
wrench
1/4-inch hex socket
and ratchet
Tape measure
Electric drill
1/4-inch drill bit
-5-
INSTALLATION
Pick a location which will allow you to blow the cold
air into the area you want. Windows used for
installation must be strong enough to support the
weight of the air conditioner. Good installation with
special attention to the proper position of the unit will
lessen the chance that service will be needed.
If air conditioner is blocked by a storm window frame,
see step 9 on page 7 before beginning to install.
HOW TO INSTALL
DSIDE CURTAINS
Insert the side curtains into the guides of the air
conditioner. Fasten the curtains to the unit with
screws (ITEM A), as shown in FIG. 2.
ITEM A FIG. 2
_"_ FOAM STRIP
Cut the adhesive-backed foam strip (ITEM D) to the
window width.
Remove the backing from the foam strip and attach the
foam strip to the underside of the bottom window. (FIG. 3)
Q ATTACH L BRACKET
Use screws(ITEM A) to install the L brackets
on the outer sill as shown. See Fig. 5.
The bracket helps to hold unit securely in place.
Be sure to place bracket edge flush against back
of inner sill. See FIG. 5.
If air conditioner is blocked by storm window
frame, see step 9.
INNER SILL
OUTER SILL ITEMA INSIDE
_,ENTERLINE
OUT81DE
L BRACKET
FIG. 5
DRAINAGE
First, be sure to insert the drain pipe into base pan
before installation. The air conditioner must be
installed with a slight tilt(I/4") downward for proper
drainage of excess condensed water through the
drain pipe.
FIG. 3
_lJ LOCATING UNIT IN WINDOW
Open the window and mark center line with pencil
on the center of the inner sill, as shown in FIG. 4.
INNER SILL
_r
ROOM SIDE
FIG. 4
DRAINCAP
DRAINPIPE
DRAIN PIPE
\
REAR
BASE PANBOTTOM
FIG. 6
-6-
r_ INSTALL THE AIR CONDITIONER IN THE
WINDOW
Carefully lift the air conditioner and slide it into the open
window. Make sure the bottom guide of the air conditioner
drops into the notches created by the L brackets.
When the air conditioner drops into the L brackets, the
air conditioner will be centered in window opening as
shown in FIG. 7.
While steadying the air conditioner, carefully bring the
window sash down behind the upper guide of the air
conditioner, as shown in FIG. 8.
\ I"
CENTER LINE FIG. 7
WINDOWFRAME
UPPERGUIDE
BOTTOM
GUIDE
L BRACKET
FIG. 8
U SECURE THE GUIDE PANELS
Extend the guide panels (ITEM F) to fill the window
opening using 4 screws (ITEM B) to secure them, as
shown in FIG. 9.
_J INSTALL THE FOAM SEAL AND SASH LOCK
Cut the foam seaI (ITEM E) to the window width.
Stuff the foam seal between the lower and upper
window sash to prevent air and insects from getting
into the room, as shown in FIG. 9.
Fasten the remaining L bracket on either side of the
window using screw (ITEM A). See FIG. 9 inset.
Installing this bracket prevents unit falling from window
being raised
Remove the screw on lower right side of cabinet.
Use this screw to attach the support bracket(iTEM H)
to the inner window sill as shown Fig. !0.
Jil
ITEMB
°
_'-]IF AIR CONDITIONER IS BLOCKED BY STORM
WINDOW FRAME
if storm window presents interference, fasten a 2" wide
wood strip to the inner window sill across the full width of
the sill. The wood strip should be thick enough to raise
the height of the window sill so that the unit can be
installed without interference from the the storm window
frame. See FIG. ! 1.
Top of wood strip should be approximately 3/4" higher
than the storm window frame to help condensation to
drain properly to the outside.
Install a second wood strip (approximately 6" long by
11/2"wide and same thickness as first strip) in the center
of the outer sill flush against the back of the inner sill.
Screw the L brackets into this strip.
This will raise the L bracket as shown in FIG. 11.
WOOD STRIP MOUNTED 1" MAX
3/4"
ON TOP OF INNER SILL CLEARANCE"T
WINDOW
INNER FRAME
SILL WOOD STRIP
FOR L BRACKET I ! I
OLJTER
SILL
INSIDE TSIDE FIG. 11
REMOVAL FROM WINDOW
Turn the air conditioner off, and disconnect the power
cord. Remove the L bracket and the screws installed
through the top and bottom of the side panels, and save
for reinstallation later. Close the side panels. Keeping a
firm grip on the air conditioner, raise the sash, and
carefully tilt the air conditioner away from you, to drain any
condensate water. Lift the air conditioner from the window
and remove the foam seal from between the windows.
Airconditionerscoveredin thismanualposean
excessiveweighthazard.Twoor morepeopleare
neededtomoveandinstalltheunit.
Topreventinjuryor strain,useproperliftingand
carryingtechniqueswhenmovingunit.
Whenhandlingtheairconditioner,becarefultoavoid
cutsfromsharpmetalfinsonfrontandrearcoils.
Makesureairconditionerdoesnotfa!lduringremoval.
-7-
HOW AND WHY
Your room air conditioner provides the following
functions to make hot weather living more
comfortable:
Cools and circulates room air.
Lowers humidity by removing excess moisture.
Filters out summertime dust, dirt, and some
airborne impurities.
The air conditioner performs these functions by
drawing room air through a filter which traps dust
and dirt particles. The air then passes over a
cooling coil which refrigerates the air and removes
excess moisture. The same air is then returned to
the room- cooler, drier, and cleaner. Moisture
removed from the room air is carried to the outside
and evaporated.
Your air conditioner is designed to be easy to
operate and to provide plenty of cooling power.
NORMAL SOUNDS FIG.12
Aside from the regular fan motor and compressor
sounds coming from your air conditioner, you will
once in a while hear a pinging sound. This is the
result of moisture being picked up from the air in the
room and thrown against the air conditioner's fan.
This is normal and should not be cause for concern.
Also, do not be alarmed if you hear a slight hissing
or gurgling sound coming from your air conditioner
after it is off. These are normal coolant noises.
CAPACITY AND RUNNING TIME
Proper unit size is important in deciding the desired
comfort for the area you want to cool. The proper
size is determined by the number of square feet
in the area to be cooled, indoor and outdoor
temperature and humidity.
Whenever the heat or humidity load is above normal
the air conditioner must run longer and more often
to keep the desired temperature you have selected,
Under heavy heat load conditions the air conditioner
may need to run constantly to keep the temperature
you want.
At times using the MED FAN setting to circulate the
room air may make it comfortable even though the
air is not being cooled. This will decrease your cost
of use.
Compressor
The modern high efficiency
compressor may have a high
pitched hum or pulsating
noise that cycles on and off.
Unit Vibration
The unit may vibrate
and make noise
because of poor wall
or window construction.
Fan
You may hear air
movement from
the fan.
You may hear droplets of water hitting
the condenser causing a pinging or
clicking sound.
FIG. 12
-8-
FEATURES
1 15 6 5 4 32714
9 8 11 1210 13 16
FIG. 13
1. Cabinet
2. Vertical Air
Direction Louvers
3. Horizontal Air
Direction Louvers
4. inlet Grille
5. Air Filter
6. Front Grille
7. Control Panel
8. Power Cord
9. Evaporator Coil
10. Condenser
11. Compressor
12. Base pan
13. Brace
14. Upper Guide
15. Curtain
16. Remote Control
USING THE AIR CONDITIONER
To reduce the risk of fire, electric
shock, or injury to persons, read the important
SAFETY instructions section before operating this
appliance
To begin operating the air conditioner after
installation, follow these steps:
1. Plug in the air conditioner. (To prevent electrical
hazards, do not use an extension cord or an
adapter plug.)
2. Set the exhaust vent to the CLOSE position.
3. Set the TEMP Control to the coolest setting.
4. Set the MODE control at the highest COOL level.
5. Adjust the louvers for comfortable air flow.
6. Once the room has cooled, adjust the TEMP and
Mode Control to the setting you find most
comfortable.
NOTE : If the air conditioner is turned off, wait 3
minutes before restarting. This allows pressure
inside the compressor to equalize. Failure to wait 3
minutes before restarting may cause inefficient
operation.
If you move the TEMP Control to a warmer, then
immediately back to a cooler setting, the unit will
shut off. Wait 3 minutes before restarting.
VENT CONTROL
The Vent Control allows the air conditioner to
either recirculate inside air (CLOSE) or exhaust
air to the outside (OPEN). (FIG. 14)
The CLOSE position is used when maximum
cooling is desired. It may also be used for air
recirculation without cooling when the air
conditioner is set in the FAN position.
The OPEN position removes stale air from the
room and exhausts it to the outside. Fresh air is
drawn into the room through your home's
normal air passages.
The OPEN or CLOSE position can be used with
any mode selection.
PULL OPEN / PUSH CLOSE
FIG. 14
-9-
DISPLAY
IFANSPEED
• Every time you push this button, it advances the setting as follows: {High -* Low-* Med-* High}
REMOTE CONTROL SIGNAL
coo_ RECEIVER
_ _ TEMPERATURE SETTING
F_ e This button can automatically control the
_i_: :"_"E_R temperature of the room.
The temperature can be set within a range
[-TIMER
- SHUT-OFF TIME
• You will usually use shut-off time while you sleep.
• If unit isrunning, Timersets numberof hours untilshut-off.
• Everytime you pushTimer button, itadvances the Timersetting
asfollows: 1Hour-_ 2 Hours........ 12 Hoursmaximum.
of 60°F to 86°F by increments of I°F.
POWER
• Toturn the air conditionerON, push the
button.
Toturn the air conditioner OFF, push
the button again.
• This button takes priority over any other
button.
• When youfirst turn it on, the air conditioner is
on the High coolmode andthe Temp.at 72°F.
- START TIME
• If unit isoff, Timer setsnumber ofhours before unitstarts.
• Everytime you pushTimer button, itadvances the Timersetting asfollows: 1Hour -_2 Hours -*. ...... 12Hours
maximum.
MODE
- Every time you push this button, it will shift among COOL, ENERGY SAVER and FAN.
- ENERGY SAVER:
The fan stops when the compressor stops cooling.
Approximately every 3 minutes the fan will turn on and check the room air to determine if cooling is
needed.
In failure of electric power, the unit runs as previous setting operation.
HORIZONTAL AIR DIRECTION CONTROL VERTICAL AIR DIRECTION CONTROL
The horizontalairdirectionis adjustedby movingthe vertical
louversrightand leftwith yourfingertips.(FIG. 15)
J
Theverticalairdirection isadjustedby movingthe horizontaI
louversup anddownwith yourfingertips.(FIG. 16)
FIG. 15 FIG. 16
-10-
REMOTE CONTROL
NOTE: The Remote Control will not operate properly if strong light shines on the sensor window of the Air
Conditioner or if there are obstacles between the Remote Control and the Air Conditioner.
Every time you push button, you will hear a beep from the Air Conditioner.
POWER
To turn the air conditioner ON, push the button. To turn the air conditioner OFF, push the
button again. This button takes priority over any other button.
When you first turn it on, the air conditioner is on the High cool mode and the Temp. at
72°F
TEMPERATURE SETTING
This button can automatically control the temperature of the room.
The temperature can be set within a range of 60°F to 86°F by increments of I°F.
FAN SPEED
Every time you push this button it advances the setting as follows:
(High -, Low -* Med -, High)
TIMER
- SHUT-OFF TIME
You will usally use shut-off time while you sleep.
If unit is running, Timer sets number of hours until shut-off.
Every time you push Timer button, it advances the Timer setting as foilows:! Hour -*
2 Hours ......... 12 Hours maximum.
FAN SPEED
TIMER MODE
- START TiME
Ifunit is off, Timer sets number of hours before unit starts.
Everytime you push Timer button, it advances the Timer setting as follows: 1 Hour-*
2 Hours......... 12Hoursmaximum.
MODE
- Every time you push this button, it will shift among COOL, ENERGY SAVER and FAN.
- ENERGY SAVER
The fan stops when the compressor stops coaling.
Approximately every 3 minutes the fan will turn on and check the room air to determine if cooling is needed.
HOW TO INSERT BATTERIES INTO REMOTE CONTROL
1. Remove the cover from the back of the remote
controller.
Open the cover according to the arrow direction on the
cover,
2. Insert two batteries.
Be sure that the (+) and (-) directions are correct.
Be sure that both batteries are new,
3. Re-attach the cover.
Do not use rechargeable batteries.
Such batteries differ from standard dry ceils in shape,
dimensions, and performance.
Remove the batteries from the remote controller if the air
conditioner is not going to be used for an extended
length of time.
-11 -
AIR FILTER CLEANING
The Air Filter will become dirty as it removes dust
from the inside air. It should be washed at least
every 2 weeks. If the Air Filter remains full of dust,
the air flow will decrease and the cooling capacity
will be reduced, possibly damaging the unit.
• Pull the inlet grille forward, grasping both tabs,
then pull out the air filter. (FIG. 17)
• Wash the Air Filter under the faucet with warm
water. Be sure to shake off all the water before
replacing the filter. (FIG.18)
FIG . 17 FIG. 18
HOWTOREMOVETHEFRONTGRILLE
Open the inlet grille downward.
Remove the screw securing the Front Grille.
Push the grille up from the bottom and pull the top
of the grille away from the case to lift the top tabs
out of their slots.
Grille
Grille
FIG. 20
AIR CONDITIONER CLEANING
Clean the front grille and inlet grille by wiping with a
cloth dampened in a mild detergent solution.
The cabinet may be washed with mild soap or
detergent and lukewarm water, then polished with
liquid appliance wax.
To ensure continued peak efficiency, the condenser
coils (outdoor side at the unit) should be checked
periodically and cleaned if they become clogged
with soot or dirt from the atmosphere. Brush or
vacuum exterior coils to remove debris from fins.
FIG. 19
HOW TO REPLACE THE
FRONT GRILLE
Attach the front grille to the cabinet by inserting the
tabs on the grille into the slots on the front of the
cabinet. Push the grille in until it snaps into place.
_ °
FIG. 21
-12-
BEFORE CALLING FOR SERVICE
Check the following list to be sure a service call is really necessary. A quick reference to this manual may
help you avoid an unneeded service call.
THE AIR CONDITIONER WILL NOT OPERATE
Check if... Then...
WaII plug disconnected.
House fuse blown or circuit breaker tripped.
Power is OFF.
Unit was turned offand then on too quickly.
TEMP Control set warmer than room temperature.
Push ptugfirmly into waIIoutIet.
Replace fuse with time delay type or reset circuit breaker.
Push the power button.
Set unit off andwait 3 minutes before restarting.
Set TEMP Control to cooler temperature.
AIR FROM UNIT DOES NOT FEEL COLD ENOUGH.
Check if... Then...
FAN SPEED set at LOW. Push FAN SPEED button to set at HI,
TEMP Control set too warm. Set TEMP Control to a cooler temperature.
Room temperature below 70F (21C). Cooling may not occur untiI room temperature rises above 70F (21C).
Temperature sensing tube touching evaporator coil, Straighten tube away from evaporator coil.
located behind front grille.
THEAIR CONDITIONERCOOLING, BUT ROOM IS TOO WARM - ICEFORMING ON COOLING COIL BEHINDFRONT GRILLE.
Check if... Then...
Outdoor temperature below 70°F (21°C). To defrost the coil, set the MODE to FAN.
Air filter may be dirty. Clean airfilter. Refer to Maintenance section of owner's manual.
TEMP Control set too cold for night-time cooling. To defrostthecoil,set the MODE to FAN or "High Coot" withthe
TEMP controltowarmertemperature.
THEAIRCONDITIONERCOOLING, BUTROOM18TOOWARM.
Check if... Then...
Dirty air fitter- air restricted. Clean airfilter. Refer to Maintenance section of owner's manual.
TEMP Control set too warm. Set TEMP Control to cooler temperature.
Front of unit is blocked by drapes, blinds, furniture, etc. Clear blockage in front of unit.
Air distribution is restricted.
Doors, windows, registers, etc. open. Cold air escapes. Close doors, windows, registers, etc.
Unit recently turned on in hot room. Allowadditionaltimetoremovestoredheatfromwalls,ceiling,floor,andfurniture.
THE AIR CONDITIONER TURNS ON AND OFF RAPIDLY.
Check if... Then...
I Outside temperature is extremely hot. I Set FAN SPEED on Hi tobring air past cooling coils faster. I
NOISE WHEN UNIT IS COOLING.
Check if... Then...
t Sound offan hittingwater from the moistureremovalsystem.[ This is normal wh,en humidity is high_.Close doors, windows, and registers.
Window vibration - poor installation. / Refer to nsta aton nstructons or check wth nsta er.
WATER DRIPPING INSIDE ROOM WHEN UNIT IS COOLING.
Check if... Then...
The air conditioner is improperly instaIled, instaIIationTiltair conditionerinstructionsSIightIYortOchecktheoutsidewithinstaller.t°allow water drainage. Refer to
WATER DRIPPING OUTSIDE WHEN UNIT IS COOLING.
Check if... Then...
The unit is removing large quantities of moisture This is normal during excessively humid days.
from humid room.
-13-
-14-
INDICE DE MATERIAS ............................. 15
GARANTiA ................................................ 15
SEGURIDAD .............................................. 16
Importantes instrucciones de seguridad .....16
REQU ERIMIENTOS ELECTRICOS ......... 17
INSTALAClON ........................................... 18
Requerimientos para instalacion .......... 18
Installacion ............................................ 19
Como instalarlo ..................................... 19
La eliminacion de la ventana ................. 20
OPERACIiN .............................................. 21
Como y por que .................................... 21
Sonidos normales .................................. 21
Capacidad y tiempo de funcionamiento ...21
Caracteristicas ..................................... 22
Uso del equipo de aire acondicionado ..22
Despliegue ............................................ 23
Control remoto ....................................... 24
MANTENIMIENTO .................................... 25
Limpieza del filtro del aire ...................... 25
Limpiezadelequipode aireacondicionado....25
C_mo sacar la rejilla frontal ................... 25
C6mo a reemplaza el grille anterior ......25
CORRECClON DE FALLAS ...................... 26
Antes de Llamarparaservicio...................... 26
ACUERDOS DE PROTECClON
ESPEClALIZADA ...................................... 31
PARA PEDIR SERVIClO .......Cubierta Trasera
GARANTiA DE UN ANO POR EL
EQUIPO DE AIRE ACONDICIONADO
DE HABITACION
Durante un aSo completo a partir de la fecha de
compra, si este equipo de aire acondicionado recibe
mantenimiento y se utiliza para el enfriamiento
normal de habitaci6n segun las instrucciones
indicadas en este manual del propietario, Sears
reparar& gratuitamente este equipo de aire
acondicionado, si tiene algQn defecto en materiales
o fabricacion.
GARANT[A TOTAL DE CINCO A_IOS
POR EL SISTEMA DE REFRIGERAClON
HERMI_TICAMENTE SELLADO
Durante cinco afios a partir de la fecha de compra,
si este equipo de aire acondicionado recibe
mantenimiento y se utiliza para el enfriamiento
normal de habitacion segun las instrucciones
indicadas en este manual del propietario, Sears
reparara gratuitamente el sistema de refrigeraci6n
hermeticamente sellado (que consiste en el agente
refrigerante, los tubos de conexiOn y el compresor),
si tiene algL_ndefecto en materiales o fabricaciOn.
EL SERVIClO DE GARANTJA ES
DISPONIBLE CONTACTANDO AL SERVIClO
SEARS AL 1-800-4-MY-HOME ®
La proteccion de garantia cubre unicamente a los
equipos de aire acondicionado usados para uso
domestico y no para uso comercial.
Esta garantia sSIo tiene vaNdez mientras el producto
se este usando en los Estados Unidos.
Esta garant afle da derechos legales especificos y
usted puede tenet otros derechos que varian de
estado en estado.
Sears, Roebuck and Co., D/817WA,
Hoffman Estates, IL 60179 U.S.A.
/
-15-
IMPORTANTES INSTRUCCIONES DE SEGURIDAD
Las siguientes instrucciones de seguridad le indicar&n c6mo usar su equipo de aire acondicionado de
habitaci6n para evitar daSos para usted mismo y para su EQUIPO DE AIRE ACONDIClONADO.
POR SU SEGURIDAD
No almacene ni use gasolina u otros vapores y
liquidos inflamables cerca de este o cualquier otro
electrodomestico. Lea las etiquetas de los
productos para ver si contienen advertencias sobre
el caracter inflamable de los mismos y otras
advertencias.
PARA PREVENIR ACCIDENTES
Para reducir el riesgo de incendios, descargas
electricas o lesiones personales al usar su equipo
de aire acondicionado, tome las precauciones
basicas, entre las que estan las siguientes:
AsegQrese de que la alimentacion electrica sea la
apropiada para el modelo que usted ha elegido.
Si el equipo de aire acondicionado debe instalarse
en una ventana, a usted probablemente le
conviene limpiar primero ambos lados del vidrio.
Si la ventana es del tipo de tres paneles con un
panel incluido de pantalla, le conviene sacar la
ventana completamente antes de la instalacion.
AsegQrese de que el equipo de aire
acondicionado ha sido instalado correctamente y
con seguridad segQn se seSala en las
instrucciones separadas de instalacion que vienen
en este manual. Conserve este manual y las
instrucciones de instalaci6n para usarlos
posiblemente en el futuro al sacar o volver a
instalar esta unidad.
Use guantes al manejar el equipo de aire
acondicionado, tenga cuidado para evitar cortadas
con las afiladas aletas met&licas que se hallan en
los serpentines frontales y posteriores.
INFORMACION ELECTRICA
En la placa de serie del fabricante se indica cual es
la capacidad electrica nominal completa de su nuevo
equipo de aire acondicionado para habitaci6n. Consulte
esta placa cuando vaya a verificar los requerimientos
electricos.
AsegOrese de que el equipo de aire acondicionado
tenga una conexi6n correcta a tierra. Para reducir al
minimo los riesgos de descargas electricas e incendio,
es importante conectar el equipo correctamente a tierra.
El cord6n de alimentaci6n electrica est& equipado con
un enchufe de tres espigas con conexi6n a tierra para
protegerle contra riesgos de descargas electricas.
Su equipo de aire acondicionado debe enchufarse en
una toma de corriente de pared que tenga una conexi6n
correcta a tierra. Si la toma de corriente de pared que
usted piensa usar no est& conectada correctamente a
tierra o no est& protegida con un fusible de acci6n
retardada o con un interruptor de circuito, haga que un
electricista calificado le instale la toma de corriente de
pared en forma correcta.
No ponga a funcionar el equipo de aire acondicionado
con una cubierta protectora exterior encima. Esto podria
ocasionar dafios mec&nicos dentro del aire
acondicionado.
No use un cable de extensi6n ni un enchufe
adaptador.
_ Evite los de incendios
peligros
Y
descargas electricas. No use un cable de extensi6n ni un
enchufe adaptador. No elimine ninguna de las espigas
dei enchufe del cordon de atimentaci6n etectrica.
Toma de corriente
de pared con
conexion
a tierra.
En ninguna ]
circunstancia code,
extraiga o intente /
eliminar la espiga de /
conexion a tierra de este_
enchufe, l
Cordon de atimentaci6n
electrica con
\
enchufe de tres espigas con
conexion a tierra.
IDEAS PARA AHORRAR ENERGiA
La capacidad del equipo de aire acondicionado
debe corresponder al tamar_o de la habitac{on
para el funcionamiento eficiente y satisfactorio del
equipo.
Instale el equipo de aire acondicionado de
habitaci6n en el ]ado sombreado de su hogar. Una
ventana orientada hacia el norte es la mejor
porque tiene sombra la mayor parte del dia.
No bloquee el flujo de aire hacia el interior con
persianas, cortinas o muebles; o la parte de
afuera con arbustos, paredes u otras
construcciones.
Cierre el regulador de tiro de la chimenea, las
rejillas de calefaccion del piso y la pared, de tal
modo que el aire frio no se escape ni por la
chimenea ni por los conductos.
Mantenga las persianas y las cortinas de otras
ventanas cerradas durante la parte mas soleada
del dia.
Limpie el filtro del aire como se recomienda en la
seccion "MANTENIMIENTO" de este manual.
El aislamiento correcto y las juntas hermeticas en
puertas y ventanas en su hogar le ayudaran a
mantener el aire caliente afuera y el aire frio
adentro.
AI darle sombra externamente a la casa con
arboles, plantas o toldos ayudara a reducir la
carga de trabajo del equipo de aire acondicionado.
Opere los aparatos que producen calor como, por
ejemplo, hornos, lavadoras, secadoras y
lavaplatos durante la parte mas fria del dia.
-16-
RESPETE TODO8 LOS CODIGOS Y
REGLAMENTO8.
BAJO NINGUNA CIRCUNSTANCIA CORTE,
QUITE 0 EVITE EL US0 DE LA CONEXION A
TIERRA DE ESTA CLAVIJA.
ESTE APARATO NECESITA 8ER
CONECTADO A TIERRA.
Se requiere una alimentaci6n electrica CA,
adecuadamente conectada a tierra con un fusible
de 15 A, de 60 Hz y de 115 V. Se recomienda un
fusible de retardo o un disyuntor de circuito que
alimente solamente a este aparato.
NO U8E CABLE ELECTRICO DE EXTENSION.
METODO RECOMENDADO DE CONEXION A
TIERRA
Por su propia seguridad este aparato debe
conectarse a tierra. Este aparato viene equipado
con un cable de alimentaci6n y una clavija de tres
terminales. Para reducir al maximo el peligro de
choque electrico, el cable debe estar conectado a
una conexi6n de pared con conexi6n a tierra, y
esta conexi6n debe hacerse de acuerdo con la
Qltima edici6n del C6digo Electrico Nacional
(ANSI/NFPA 70), asi como con los c6digos y
reglamentos locales. Si no existe una conexi6n
de pared adecuada, el cliente tiene la
responsabilidad y la obligaci6n de mandar
instalar, con un electricista calificado, una
conexi6n de pared adecuada de tres terminales
con conexi6n a tierra.
Peligrode choqueelectrico
Conecteen unaconexi6nde paredde 3 terminales
Noquitela terminalde conexi6na tierra
No useadaptadores
No usecableelectricode extensi6n
Si no sesiguenestasinstrucciones,puede
ocasionarsela muerte,un incendioo un choque
electrico.
Cable de alimentacion con
clavija dotada de conexion I
a tierra de 3 terminales. _ I
Toma de corriente _ _ I1[I___'_I
de pared con _"_ ))I
conexion a tierra, k_ i _
N Terminal de
conexion a tierra.
[
Bajo ninguna cireunstancia eorte, quite e
evite el uso de la eonexi6n a tierra de esta elavija.
-17-
REQUERIMIENTOS PARA
INSTALAClON
Su equipo de aire acondicionado se instalara en ventanas
estandar de doble panel con anchos de abertura libre de 559 mm
a 914 mm (22 a 36 puigadas). (Figura 1)
El marco inferior debe abrirse Io suficiente para permitir una
abertura vertical tibre de 331 mm (13 pulgadas). Las rejillas
desviadoras laterales y la parte posterior del equipo de aire
acondicionado deben tener un espacio libre de aire para permitir
suficiente flujo de airea traves dei condensador para asi eiiminar
el calor. La parte posterior de la unidad debe quedar al aire libre,
no dentro de un edificio o garaje.
._._ _------_H Banda
22" to 36" _'_ I
II
I 1113"rnin Repisa I I --Ventana
(,IJ ,r .'_ Antepecho
' Exteri°r
Pared interior ....... Figura I
8ERVICIOELECTRICO
Compruebe cual es la alimentacion eiectrica que Ilega a su
domicilio. La alimentacion electrica disponibie debe ser la misma
que se muestra en laplaca del fabricante de la unidad (que se
halla en el lade izquierdo del gabinete de corriente alterna).
Todos los modelos estan equipados con unenchufe de tres
espigas para suministrar un servicio correcto y una conexi6n a
tierra segura y positiva. Nocambie el enchufe de ninguna forma.
No use unenchufe adaptador. Si su toma decorriente de pared
actual no puede usarse con el enchufe del equipo, llame a un
electricista catificado para que efectOe las correcciones
necesafias.
CONSERVE LA CAJA y este MANUAL DEL PROPIETARIO para
que le sirva como referencia en el futuro. La caja es la mejor
manera de conservar la unidad durante el invierno o cuando no
esta en use.
Para evitar el riesgo de heridas personales, daSos en
los bienes, o daSo en el producto debe ser expuesto ei
agudez de los bordes y el peso apto del aparato:
El aire acondicionado del que se habla en este
manual afirma peligro de peso excesivo.
Dos o mas personas se requiere para mover e instalar
la unidad. Para evitar heridas o agotamlento, use
tecnicas apropiadas para levntar y mover Ia unidad.
Cuidadosamente inspeccione eI lugar donde eI aire
acondicionado sera puesto. Asegurese que el lugar
sostenga el peso de la unidad sobre un periodo de
tiempo prolongado.
Mantenga su aire acondicionado con cuidado. Use
guantes protectores cuando levante o mueva la
unidad. EVITE las aletas filosas de metal en el
serpentin delantero y de atras.
Asegurese que el aire acondicionado no se caiga
durante la instalacion.
INSTALACION PIEZAS DE MONTAJE
TIPO NOMBREDELABPIEZA8 CANTIDAD
A TORNILLO CORTO 11
B TORNILLO MEDIANO 5
C SUPPORT EN L 3
D BANDA ADHESIVA 1
E BANDA DELMARCO 1
F PANEL DE GUiA 2
G TUBO DE DRENAJE 1
H SOSTENGA PARENTESIS 1
HERRAMIENTAS REQUERIDAS
Guantes apretados Llave inglesa o Ilave
Destomillador normal abierta de 3/8"
Destomillador Phillips Llave hexagonal de cubo
Pinsas y trinquete de 1/4 de
Cuchillo filoso pulgada
Cinta para medir
Taladro electrico
Broca de taladro de 1/4"
-18-
INSTALACl0N
Escoja un lugar que le permita Ilevarel aire frio al &rea
quedesea. Las ventanas que se usen para la instalaci6n
deben tener la resistencia suficiente para soportar el peso
delequipo de aire acondicionado. Una buena instalaci6n
con atenci6n especial a la correcta posici6nde la unidad
disminuir&la probabilidad de que sea necesario efectuar
reparaciones.
C0MO INSTALARLO
H CORTINAS LATERALES
Inserte las cortinas laterales en las guias del aire
acondicionado. Fije las cortinas a la unidad con
tornillos (TIPO A), como se muestra en Figura 2.
TIPO A
TIPO A Figura 2
_'1FAJA DE SELLANTE
Corte la cinta selladora adhesiva (TIPO D) a la anchura
de laventana.
Quite el dorso de la cinta selladora y peque la cinta
selladora a la superficie inferior de la ventana de abajo.
Vea la Figura 3.
Figura 3
COLOCAR LA UNIDAD EN LA
VENTANA
Abra la ventana y marque la linea central en el centro del
alf izar interior como se muestra en la Figura 4.
ANTEPECHO
INTERIOR
TABURETE
Figura 4
D SOPORTE DE FIJACION L
Utilice tornillos(TIPO A) para instalar los soportes
en L sobre la plataforma exterior como se
muestra. Consulte Figura 5.
El soporte ayuda a mantener la unidad
correctamente en su lugar. AsegQrese de colocar
el borde del soporte nivelado con la parte de atr&s
del alfeizar interior. V6ase la Figura 5.
• Si el aire acondicionado est& bloqueado pot el
marco de la ventana de tormenta, v6a el paso 9.
DESCANSO
EXTERIOR
\
\
\
DESCANSO
INTERIOR
TIPO A
INTERIOR
LINEA DEL CENTRO
EXTERIOR
MENSULA EN L
gura 5
DRENAJE
En primer lugar, asegQrese de insertar la tuberia
de drenaje en la bandeja de la base antes de la
instalaci6n. El aire acondicionado debe instalarse
con una ligera inclinaci6n (1/4") hacia abajo para
el drenaje adecuado del exceso de agua condensada
a traves de la tuberia de drenaje.
4ira
TUYAU
DRENAJE DI_VACUATION
PARTE POSTERIOR
TUBO DE H- DEL RECIPIENTE
DRE_,_ DE BASE
PARTE INFERIOR DEL
_- REOIPIENTE DE BASE
'_111//////////////_
Figura 6
-19-
r_ INSTALE EL ACONDICIONADOR DE AIRE
EN LA VENTANA
Levanteconcuidado el aire acondicionadoy desicelohasta
laventanaabierta.Asegt_resedeque la guia inferiordelaire
acondicionadopasa porlas muescasde lossoportesen L
• AI encajar en del soporte L, el acondicionador de aire
estate,centrado en la abertura de la ventana, come se
muestra en la Figura 7.
Mientras sujeta el acondicionador de aire, baje
cuidadosamente el marco corredizo de la ventana
detr_.sde la guia superior del acondicionador de aire,
como se muestra en la Figura 8.
iY
r,"
1 LIn_eeacentral I"_' Figura 7
BORDE DE LA VENTANA
SUPERIOR -.
/
GUIASUPERIOR --_ _- BANDA
Figura 8
H FIJE LOS PANELES CORREDIZOS
Extienda los paneles corredizos para Ilenar la abertura de
la ventana, usando los 4 tornillos (TIPO B) parafijarlos,
come se muestra en la Figura 9.
D INSTALE EL SELLO DE VENTANA CORREDIZA Y
EL SEGURO DE VENTANA CORREDIZA
• Corte lajunta de espuma(TIPO E) a la anchura de la
ventana.Meta la juntade espumaentre el marco inferior
y superior de la ventana para evitarque entre aire e insectos
en la sala,come semuestraen Figura9.
• Coloqueel soporteen L restanteen unode los dos lados de
la ventana utilizandountornillo (TIPOA). Consulteel detalle
de Figura9. La instalacio'nde este soporteevita que la
unidad caiga cuandose levante laventana.
_- _-'--_J3 Figura 9
pP'_ [_Ul Im7:1m[o_
Retireel tornillode la parte inferiorderecha de lacarcasa.
•Utiliceeste tornillopara incorporarel soportede apoyo
(TIPOH) a laplatatormainterior de laventana,
comose muestra enFigura10.
--_ _ TIPO_,_
'-> _ Figura 10
_'_SI ELACONDICIONADORDEAIREESTABLOQUEADO
POREL MARCODELACONTRAVENTANA
Si la contraventanainterfiere,fijeunlist6ndemaderade2"de
anchoal alf6izarinteriordela ventana,queatraviesela
anchuratotaldelalf6izar.El list6ndemaderadebeser
suficientementegruesoparalevantarlaalturadelalf6izardela
ventanadetal maneraquela unidadpuedaserinstaladasin la
interferenciadelmarcodelacontraventana.Veala Figura11.
Lapartesuperiordellist6ndemaderadebeser
aproximadamente3/4"m_.saltoqueel marcodela
contraventanao el list6ndemadera(fueradelacasa)para
queelvaporemanadodela unidadpuedadrenar
adecuadamentehaciael exterior.
• Instaleunsegundolist6ndemadera(deaproximadamente6"
de largoy 1"deanchoy delmismogrosordelprimerliston)en
el centrodelalf6izarexteriorniveladoconla parteposteriordel
alf6izarinterior.AtornillelossoportesL entrela faja.Esto
levantar_elsoporteLcomosemuestraenla Figura11.
1" MAX.
FRANJA DE MADERA _ 3/4-PULG
MONTADA SOBRE "_ _ _ DE SEPARACION
LA PARTE SUPERIOR _'_'_ _ n L
DEL DESCANSO
INTERIOR __-'_, VENTANA DE A
ooe
ANTEPECHO
INTERIOR
AN:rEPECHO
_N ERRORFigura 11
LA ELIMINACI6N DE LAVENTANA
Apagueel aire acondicionadoy desenchufeel cablede
alimentaci6n.Retireel soporteen Ly lostornillosinstalados
en laparte superiore inferiorde los paneleslateralesy
gu&rdelospara la posterior reinstalaci6n.Cierrelos paneles
laterales.Sujetandofirmemente elaire acondicionado,
levanteel marcoe inclinecon cuidadoel aireacondicionado
hacia afueraparadrenar todael agua condensada.Levante
el aireacondicionadode la ventanay retirelajunta de
espumadeentrelas ventanas.
Elaireacondicionadodelquesehablaenestemanualafirmapeligro
depesoexcesivo.
Dosomaspersonasserequiereparamovereinstalarlaunidad.Para
evitarheridasoagotamlento,usetecnicasapropiadasparalevntary
moverlaunidad.
AImanejarlaunidad,tengacuidadoparaevitarcortarseconlasalertas
met_licasafiladasqueest_nenlosserpentinesfrontalyposterior.
Aseguresequeelaireacondicionadonosecaigadurantelainstalacion.
- 20 -
COMO Y POR QUI
Su equipo de aire acondicionado de habitaci6n
brinda las siguientes funciones para hacer que la
vida en climas c&lidos sea m&s confortable:
Enfria y hace circular el aire per la habitaci6n
Disminuye la humedad eliminando la humedad
excesiva.
Filtra el polvo, el sucio y algunas impurezas
transportadas en el aire del clima veraniego.
El equipo de aire acondicionado realiza estas
funciones haciendo pasar el aire del medio
ambiente a traves de un filtro que atrapa las
particulas de polvo y sucio. El aire pasa entonces
pot un serpentin de enfriamiento que refrigera el
aire y elimina el exceso de humedad. El mismo aire
regresa entonces al enfriader, secador y limpiader
del aire del ambiente. La humedad extraida del aire
ambiente es Ilevada al exterior y evaporada.
Su aire acondicionado est& diseSado para operar y
suministrar una enorme potencia de enfriamiento.
SONIDOS NORMALES Figura 12
Adem_s de los sonidos regulates del motor del
ventilador y el compresor que salen de su equipo
de aire acondicionado, usted escuchar& de vez en
cuando un sonido met&lico. Este sonido es
producido per la humedad que es recogida del aire
en el ambiente yes lanzada contra el ventilador del
equipo de aire acondicionado. Esto es algo normal
que no debe set motive de preocupaci6n. De igual
mode, no se alarme si usted escucha un ligero
sonide de silbido o borboteo proveniente de su
equipo de aire acondicionado despu6s que Io
apaga. Estos son ruidos normales del refrigerante.
CAPACIDAD Y TIEMPO DE
FUNCIONAMIENTO
AIdecidircu_.ldebeserla comodidaddeseadaparael &reaque
ustedquiereenfriar,esimportantedeterminareltamaSocorrecto
delaunidad.Unaunidadpequenanotendrala capacidadpara
enfriar,dejandolaareacahrosa.EltamaSoadecuadoes
determinadoporel nL_merodemetroscuadradosquetieneel
&reaquese deseaenfriar,asi comoporlatemperaturainteriory
exterioryporlahumedad.Unaunidaddemasiadograndesi
enfria,peronodeshumedece,dejandolaareafriay humeda.
Siemprequelacargat_rmicadelventiladorest_porencimade
Ionormal,el equipodeaireacondicionadodebefuncionarm_.s
tiempoparamantenerlatemperaturadeseadaqueustedha
seleccionado.Bajocondicionesdeunacargat_rmicamuy
pesada,puedeser necesarioqueelequipodeaire
acondicionadofuncioneconstantementeparamantenerla
temperaturadeseada.
Enocasiones,el usode MEDFANparahacercircularelairepor
la habitaci6nhacequeelambienteseam&sconfortableaun
cuandoelequiponoest6enfriandoel aire.Mientrasm&stiempo
y conmayorfrecuenciafuncioneelequipodeaire
acondicionado,m_.selectricidadconsumir&ymayoresser_.nlos
costosdesuuso.
Compresor
El moderno compresor de gran
eficiencia puede producir un ruido
agudo de murmullo o un ruido de
pulsaci6n queviene y se va.
Vibraciones de la
unidad
La unidad puede vibrar y
hacer ruido debido a la
deficiente construcci6n
Ventilador
Usted puede
escuchar el
movimiento del
aire proveniente
del ventilador
Condensador
Usted puedeescuchar gotas de agua que caen
sobre el condensador causando un sonido
met&licoo un sonido de chasquido.
Figura12
-21 -
CARACTERiSTICAS
1 15 6 5 4 32714
9 8 11 1210 13 16
Figura 13
1. Gabinete
2. Deflector vertical
de aire
3. Deflector horizontal
de aire
4. Toma de aire
5. Filtro del aire
6. Parrilla frontal
7. Tablero de control
8. Cord6n de
alimentaci6n
el6ctrica
9. Evaporador
10. Condensador
11. Compresor
12. Recipiente de base
13. Puntal
14. Guia superior
15. Cortina
16. Control remoto
-22 -
USO DEL EQUIPO DE AIRE
ACONDICIONADO
_Para reducir el riesgo de incendio,
descargas el6ctrica o lesiones personales, lea las
IMPORTANTES INSTRUCClONES DE
SEGURIDAD antes de operar este aparato.
Para comenzar a utilizar el equipo de aire
acondicionado, siga eetos pasoe:
1. Enchufe el equipo de aire acondicionado. (Para
prevenir riesgos de descargas el_ctricas, no use
un cable de extensi6n ni un enchufe adaptador.)
2. Ajuste el extractor de aire en la posici6n CLOSE.
3. Ajuste el control de MODE al mas alto nivel
fresco.
4. Ajuste el control del ventilador al m_s alto nivel.
5. Ajuste las rejillas desviadoras para Iograr un flujo
confortable de aire.
6. Una vez que la habitaci6n se haya enfriado,
ajuste el control de temperatura TEMP a la
graduaci6n que usted considere m&s confortable.
NOTA: Si se apaga el aire acondicionado, espere 3
minutos antes de volver a encenderlo. Esto permite
que se estabilice la presi6n dentro del compresor.
Si no sigue estas instrucciones, el equipo podria
funcionar con poca eficiencia.
Si usted mueve el TEMP el control a un warmer,
entonces inmediatamente espalda a una colocaci6n
m&s fresca, la unidad apagar&. Espere 3 minutos.
CONTROL DE VENTILAClON
El control de ventilaci6n permite que el equipo de aire
acondicionado haga recircular el aire en el interior de la
habitaci6n (CLOSE) o saque el aire hacia el exterior
(OPEN). (Figura 14)
La posici6n CLOSE sirve cuando se desea un
enfriamiento m&ximo. Tambi_n puede usarse para
hacer recircular el aire sin enfriar la habitaci6n cuando
el equipo de aire acondicionado se ajusta en la
posici6n FAN.
La posiciOn OPEN extrae el aire estancado de la
habitaci6n y Ioexpulsa hacia fuera. El aire fresco es
Ilevado hacia el interior de la habitaci6n a traves de
los pasajes normales de aire que se hallan en los
hogares.
La posici6n OPEN o CLOSE puede usarse con
cualquier selecci6n de ventilador.
PULL OPEN / PUSH CLOSE
(TIRARPARAABRIR/ EMPUJARPARACERRAR)
Figura14
DESPLIEGUE
_-VELOCIDAD DEL VENTILADOR
• Cada vez que presione este bot6n, el ajuste es como sigue: {Alto -* Bajo-* Medio-* Alto}
DE SENAL
¢o_lo
DE LA TEMPERATURA
Este boton puede controlar la temperatura
'T'EMP del cuarto automaticamente.
La temperatura se puede ajustar de grado
en grado, desde 60°F hasta 86°F cada 1°F.
_-MARCADOR DE ENCENDIDO/APAGADO
- OPERACION DE PARADA:
• Si ta unidadcorre,et nL]merode conjuntosde Retojde horas
hastaapag6.
ENECNDIDO/APAGADO
• Para ENCENDERet sistemapresione el boton,
y para APAGARLO presioneel bot6n otra vez.
• Este boton tiene prioridadsobre todos los otros
botones.
• Cuando Ud. Ioenciende por primera vez,et
sistema esta en el y ta temperaturaes de 72F.
• Cada vezque presioneeste boton, cuando etsistemaeste operando,el marcadorde tiempo seajustara de tasiguiente
manera: 1Hora-, 2 Horas-, 3 Horas......... 12Horas maximas.
- OPERACIONDE INIClACION:
• Si ta unidadesta apagada,el m]merode conjuntosde Retojde horasantesde comienzos de unidad.
• Cada vez quepresioneeste boton, cuando etsistemaeste operando,el marcadorde tiempo seajustara de tasiguiente
manera: 1Hora-, 2 Horas-, 3 Horas......... 12Horas maximas.
MODO
- Cado vez que presione este bot6n, cambiara entre COOL(FRESCO), ENERGY SAVER(ECONOMICO)
y FAN(VENTILADOR)
- AHORRADOR DE ENERGiA:
• El ventilador se detiene cuando el compressor no sigue enfriando.
Aproximadamente cada 3 minutos el ventilador se encendera, y necesitara verificar la temperatura del
cuarto para saber si es necesario mas enfriamiento.
_orriente electrica, la unidad funcionara como antes cuando vuelve la corriente. J
1
CONTROL DE LA DIRECCION CONTROL DE DIRECCION VERTICAL DEL AIRE
LadireccionhorizontaIdelaireesajustadarotandolapatanca Ladirectionverticaldoiairoseajustamoviendola rojiIla
verticalhacialaderochao haoialaizquierda.(Figura.15) horizontalhaciadolanteohaciaatras.(Figura.16)
Figura26 Figura16
- 23 -
CONTROL REMOTO
Precauci6n: El dispositiovo de control remoto no funcionara adecuadamente si la ventana sensora del
acondicionador de aire es expuesta a luz fuerte, o si hay obstaculos entre el dispositivo de control remoto y
el acondicionador de aire. Cuando opere el aire acondicionado con el control remoto, deber& oir un pito.
ENECNDIDO/APAGADO
Para ENCENDER el sistema presione el bot6n, y para APAGARLO
presione el bot6n otra vez.
Este bot6n tiene prioridad sobre todos los otros botones.
Cuando Ud. Io enciende por primera vez, el sistema esta en el y la
temperatura es de 72°F.
AJUSTE DE LA TEMPERATURA
Este bot6n puede controlar la temperatura del cuarto autom&ticamente.
La temperatura se puede ajustar de grado en grado, desde 60°F hasta
86°F cada 1°F.
VELOClDAD DEL VENTILADOR -_
• Cada vez que presione este bot6n, el ajuste es como sigue: |
{Alto -* Bajo -* Medio -* Alto}
/
MARCADOR DE ENCENDIDO/APAGADO
- OPERACI6N DE PARADA:
• Si la unidad corre, el nQmero de conjuntos de Reloj de horas hasta apag6.
• Cada vez que presione este bot6n, cuando elsistema este operando, el
marcador de tiempo se ajustar& de la siguiente manera: 1Hora -, 2 Horas -,
3 Horas ......... 12 Horas maximas.
- OPERACION DE INICIACION:
• Si la unidad esta apagada, el nOmero de conjuntos de Reloj de horas antes
de comienzos de unidad.
• Cada vez que presione este bot6n, cuando elsistema este operando, el
marcador de tiempo se ajustar& de la siguiente manera: 1Hora -* 2 Horas -*
3 Horas .......... 12 Horas maximas.
TEMP
FAN SPEED
TIMER MODE
MODO
- Cado vez que presione este bot6n, cambiara entre COOL(FRESCO), ENERGY SAVER(ECONOMICO
y FAN(VENTILADOR)
- AHORRADOR DE ENERGiA:
El ventilador se detiene cuando el compressor no sigue enfriando.
Aproximadamente cada 3 minutos el ventilador se encendera, y necesitara verificar la temperatura del
cuarto para saber si es necesario mas enfriamiento.
COMO A BATERIAS DE ADICION EN EL CONTROL REMOTO
No utilice bateris recargables, estas son diferentes de
forma, de dimensi6n y uso respecto alas baterias
secas usuales.
Seque las baterias del telemando cuando el
acondicionador no vaya a ser usado durante un largo
periodo.
1. Quite la cubierta de la espalda del director remoto.
Abra la cubierta segun la direcci6n de la flecha.
2. Meta a baterias.
Este seguro que el (+) y (-) las direcciones son
correctas.
Este seguro que ambas baterias son nuevas.
3. Re-conecte la cubierta.
- 24 -
LIMPIEZA DEL FILTRO DEL AIRE
El filtro del aire se ir_lensuciando a medida que va
atrapando el polvo proveniente del aire interior. Es
preciso lavar el filtro del aire al menos cada dos
semanas. Si el filtro del aire permanece Ileno de polvo, el
flujo de aire disminuir& y se reducir_tla capacidad de
enfriamiento del equipo, con posibles daSospara la
unidad. (Figura 17)
• Tire de la rejilla de entrada hacia delante agarrando
ambas lengtietas y tire del filtro del aire hasta sacarlo.
• Lave el filtro del aire en agua tibia a. Aseg0rese de
eliminar toda el agua sacudiendo el filtro antes de volver
a ponerlo en su posicion. (Figura 18)
Figura 18
LIMPIEZA DEL EQUIPO DE AIRE
ACONDICIONADO
La rejillafrontal y la rejillade entradadelaire puedenlavarse
con unpahohumedecidoen unasoluci6ndedetergente
suave.(Figura19)El gabinetepuede lavarseconunjab6no
detergentesuavey aguatibia,seguidamentepuedepulirse
concera Ifquidaespecialpara electrodom_sticos.
Paraasegurarunaeficiencia m_lximacontinua,los
serpentinesdelcondensador(ladode enfrentede la unidad)
deben revisarseperi6dicamentey limpiarsesiestEln
obstruidoscon hollfno consuciode laatm6sfera.
Figura 19
COMOA REEMPLAZA EL
GRILLE ANTERIOR
• Saqueeltornilloque mantienela rejillafrontal enposici6n.
• Quiteel tomillo queasegurale rejadelantera.
• Empujela rejillahaciaarribade abajoy jalela partede
arribade la rejillalejosde la baseparalevantarlas
lenguetasde arribahacia afuerade las ranuras.
iliade entrada
COMO A REEMPLAZA EL
GRILLE ANTERIOR
Pegue el panel frontal a la caja insertando losfijadores
en el panel adentro losdel panel de la caja.
o
Figura 21
/
- 25 -
ANTES DE LLAMAR PARA SERVICIO
Cheque la siguiente lista para asegurarse si en realidad es necesario Ilamar para servicio. Una referencia rapida a
este manual puede evitar una Ilamada para servicio innecesaria.
EL EQUIPO DE AIRE ACONDICIONADO NO FUNCIONA.
Etenchufenoestaconectadoenlatomadecorrientedepared. Conecteelenchufeflrmementeenlatomadecomentedepared
Etfusibleestaquemadooel interruptordecircuitosehadisparado. ReemplaceelfusibledaSadoconanfusibledeacoidnretardadaoreajusteel
inteiTuptordecircuito.
ElselectordelventitadorMODEestaenla posicidndeOFF. Pongaelselectorenlaposid6ndeCOOL.
Launidadseapag6y se votvi6aencenderdemasiador_pido. Apaguela unidadyespere3minutosantesdevolveraencenderla.
ElcontroldetemperaturaTEMPseajust6m_scalidoquela AjusteelControldeIaTEMPaunatemperaturamasfria.
temperaturaambiente.
EL AIRE DE LA UNIDAD NO SALE BASTANTE FRiO.
Elselectora unaposiciOnmasLOWCOOL
ColoqueelcontroldeTEMPERATURAenunnQmeromasalto.
Latemperaturaambienteest_pordebajodelos70°F (21°C)
Eltubosensordetemperaturaest_tocandoel serpentinfrio queest_
situadodetrasdelfiltrodel aire.
Gireelselectora unaposiciOnHIGHCOOL.
AjusteelControldeIaTEMP aunatemperaturam_sfl-ia.
Nopuedeproducirseel enfriamientohastaquela temperaturaambientesuba
porencimadelos700F(21°C).
EndereceeltuboalejandoIodeIserpentin
Eifittrodelairepuedeestarsucio.
Elcontroldetemperaturase ajust6demasiadofrioparael
enfriamientonocturno
ELAIREACONDICIONADOENFRIA,PEROLAHABITACION8E81ENTEDEMASIADOCALIDA;8EFORMAHIELOENELSERPENTiNDEENFRIAMIENTO
DET_SDELPANELDECORATIVOFRONTAL.
Latemperaturaambienteenetexteriorest_potdebajodelos70°F(21°C). /ParadescongelareIserpentinIleveel selectora laposicidnFAN.
Seguidamente,gireelcontroldetemperaturaTEMPenelsentidodeiasagujas
delretojparaIlevarlohastaunagraduacidnmascalida.
Limpieelflitro.Consultelasecoi6n"Mantenimiento".Paradessongelar,Ileveel
selectora laposici6nFAN.
Paradescongetarlabobina,ajusteelMODOaFAN(Ventilador)o"Frioalto"
conelcontrolTEMPaunatemperaturam_scalida.
ELAIREACONDICIONADOENFRiA,PEROLAHABITACION8E8tENTEDEMASIADOCALIDA;NO8EFORMAHIELOENEL8ERPENTINDE
ENFRIAMIENTODETRA8DELPANELDECORATIVOFRONTAL.,
ElfiltrodelaireestasucioconIoqueserestringeelflujodetaire. Limpieetfiltrodelaire.Consultelasecoi6n"Mantenimientd'
ElcontroldetemperaturaTEMPsegradu6enposici6ndemasiadocatida. Ajusteel ControldeIaTEMPa unatemperaturamasfda.
Lapartefrontaldelaunidadest_bloqueadapercortinas,persianas, Elimineelbloqueoenfrentedelaunidad.
mueblesetc.querestringenladistribuci6ndelaire
Laspuertas,ventanas,rejillasdecalefacci6n,etcctera,estanabiertascon Cierrelaspuertas,ventanas,rejillasdecalefacci6n,etc6tera.
Ioquesepermiteelescapedelairefrio.
Launidadacabadeencenderseenunahabitacidncaliente Permitaquetranscurraunpocomasdetiernpoparaeliminarel"caloralmacenado"
enlasparedes,ettecho,elpisoy losmuebles.
EL EQUIPO DE AIRE ACONDICIONADO 8E APAGA Y 8E ENCIENDE RAPIDAMENTE.
Latemperaturaexterioresextrernadamentecaliente AjusteelMODOenlavetocidadALTAparahacerqueetairepaseperla bobina
derefrigeraci6nmasrapido.
8E ESCUCHAN RUID08 CUANDO LA UNIDAD ESTA ENFRIANDO.
Elsonidodetventitadoralchocarcontrael aguadelsistemade Estoesnormalcuandolahumedadesalta.Cierrelaspuertas,ventanasy rejillas
eliminaci6ndehumedad, decalefacciOn.
VibraciOndelaventana;instalaci6ndeficiente. Lealasinstruccionesdeinstalaci6noconsutteal instalador.
EL AGUA GOTEA DENTRO DE LA HABITACION CUANDO LA UNIDAD ESTA ENFRIANDO.
Instalaci6ninadecuada, lndineligeramenteelequipodeaireacondidonadohacialaparteextedorparapemitirel
drenajedeagua.LeaasnstruccionesdenstaacJ6noconsutea nstaador
ELAGUA GOTEA AFUERA CUANDO LA UNIDAD ESTA ENFRIANDO.
Launidadestaextrayendograndescantidadesdehumedaddeuna EstoesatgonormaldurantelosdiasexcesJvarnentehOmedos.
habitaci6nh_meda.
- 26 -
- 2-7-
1281
1291
l 301
Master Protection Agreements
Congratulations on making a smart purchase.
Your new Kenmore ® product is designed and
manufactured for years of dependable operation.
But like all products, it may require preventive
maintenance or repair from time to time.
That's when having a Master Protection Agreement
can save you money and aggravation.
Purchase a Maser Protection Agreement now and
protect yourself from unexpected hassle and
expense.
The Master Protection Agreement also helps extend
the life of your new product. Here's what's included
in the Agreement:
[] Expert service by our 12,000 professional
repair specialists
[] Unlimited service and no charge for parts and
labor on all covered repairs
[] "No-lemon" guarantee - replacement of your
covered product if four or more product failures
occur within twelve months
[] Product replacement if your covered product
can't be fixed
[] Annual Preventive Maintenance Check at your
request - no extra charge
[] Fast help by phone - phone support from a
Sears technician on products requiring in-home
repair, plus convenient repair scheduling
[] Power surge protection against electrical
damage due to power fluctuations
[] Rental reimbursement if repair of your covered
product takes longer than promised
Once you purchase the Agreement, a simple phone
call is all that it takes for you to schedule service.
You can call anytime day or night, or schedule a
service appointment online.
Sears has over 12,000 professional repair
specialists, who have access to over 4.5 million
quality parts and accessories. That's the kind of
professionalism you can count on to help prolong
the life of your new purchase for years to come.
Purchase your Master Protection Agreement today!
Some limitations and exclusions apply.
For prices and additional information call
1-800-827-6655.
Sears Installation Service
For Sears professional installation of home
appliances, garage door openers, water
heaters, and other major home items, in the
U.S.A. call 1-800-4-MY-HOME _
Acuerdos de Proteccion Especializada
iEnhorabuena! Ha realizado una compra inteligente.
Su nuevo aparato Kenmore® esta diseSado y fabricado
para ofrecerle aSos de buen funcionamiento.
Sin embargo, al igual que todos los productos, puede
precisar un mantenimiento preventive o incluso alguna
reparacion de vez en cuando. En esas ocasiones, un
Master Protection Agreement puede ayudarle a ahorrar
dinero e inconvenientes.
Adquiera un Maser Protection Agreement ahora, y
prot_jase a si mismo de molesfias y gastos inesperados.
El Master Protection Agreement le ayudara tambien a
prolongar la vida de su nuevo aparato. Los siguientes
servicios estan incluidos:
[] Servicio experto por parte de cualquiera de
nuestros 12.000 tecnicos profesionales especialistas
de Sears.
[] PrestaciCn de servicios sin limitaciones y sin
cargarle las piezas o la mane de obra en todas ias
reparaciones cubiertas pot el acuerdo.
[] Garantia seria de sustituciSn de las piezas del
producto cubierto pot el acuerdo, si cuatro o mas
piezas se mostrasen defectuosas en un periodo de
doce meses.
[] SustituciCn del producto por otro nuevo, si ei
defectuoso no pudiese repararse.
[] Control de mantenimiento anual preventivo,
siempre que Io desee y sin gasto adicional alguno.
[] Asistencia telefCnica inmediata de un tecnico
especialista en productos que hart de ser reparados a
domicilio, ademas de una programaciCn adecuada de
la reparaciCn.
[] ProtecciCn contra subidas de tensiCn que
provoquen da_os elcctricos debidos alas
fluctuaciones en el suministro.
] Reintegro del alquiler si la reparacion deI producto
Ileva mas tiempo del promtetido
Una vez que haya adquirido el Agreement, no necesitara
masque una simple Ilamada para solicitar el servicio de
su aparato. Ademas, podra hacerlo en cualquier momento
del d{a o de la noche, o solicitar una cita para prestacion
de servicios online.
Sears cuenta con mas de 12.000 tecnicos profesionales
especialistas en reparaciones, con acceso a mas de 4,5
miIIones de piezas de sustitucion y accesorios de calidad.
Este sera el tipo de profesionalidad y servicie con el que
podra contar para prolongar la vida de su nuevo producto
pot muchos ados. iAdquiera boy mismo su Master
Protection Agreement!
Se aplicar_n algunas limitaciones y
restricciones.
Si desea hacer alguna consulta sobre los
precios u otra informaciCn adicional, le rogamos
Ilame al tel_fono 1-800-827-6655.
Servicios de InstalaciCn Sears
Para solicitar servicios de instalaciSn profesionales
de Sears de electrodomesticos, mandos de apertura
de puertas de garajes, calentadores de agua y otros
aparatos en los Estados Unidos, puede liamar a
1-800-4-MY-HOME ®
-31 -
Your Home
For repair- in your home-of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For,the replacement parts, accessories and
owner s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME ® (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime, day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement(U.S.A.)
or maintenance agreement(Canada)on a product serviced by Sears:
1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)
Para pedir servicio de reparaci6n Au Canada pour service en frangais:
a domicilio, y para ordenar piezas: 1-800-LE-FOYER Mc
1-888-SU-HOGARSM {1-800- 33- 937>
(1-888- 784-8427) www.s ears.oa
TM SM
® Registered Trademark / Trademark / Service Mark of Sears, Roebuck and Co
TM S_,
® Marca Registrada / Marca de Fabdca / " Marca de Servicio de Sears, Roebuck and Co.
MC MD
Marque de commerce / Marque deposee de Sears, Roebuck and Co ® Sears, Roebuckand Co.
Part No.: 3828A21009A
1 / 1

Kenmore 580.74083 El manual del propietario

Categoría
Acondicionadores de aire de sistema dividido
Tipo
El manual del propietario

En otros idiomas