Transcripción de documentos

Specifications Marine Electrical Products e-Series Single Circuit ON/OFF Battery Switch PN 9003e Features • Disconnects single battery bank in emergencies, or when vessel is not in use • For switching battery banks in applications requiring high power output, reliability, and low heat generation Tin-plated copper studs: • 3/8”-16 (M10) provide maximum conductivity and corrosion resistance • One-piece to reduce risk of overheating • 7/8” (22.22mm) length to accept multiple cable terminals Case design: • Allows surface mounting or rear panel mounting • Accepts up to 4/0 AWG (95mm²) battery cables Cranking Rating: 30 sec. Intermittent Rating: 5 min. (UL 1107) Continuous Rating Voltage Max. Operating Terminal Stud, Tin-Plated Copper Torque Cable Size to Meet Ratings* Ignition Protected marked 1,200A 600A 350A 48V DC 3/8”-16 (M10) 140 in-lb (15.82 N·m) 4/0 AWG (95mm²) Agency Specifications • Meets all American Boat and Yacht Council (ABYC) requirements for battery switches • UL Listed - UL 1107 for electric power switches • Meets UL 1500 and SAE J1171 external ignition protection requirements Guarantee Any Blue Sea Systems product with which a customer is not satisfied may be returned for a refund or replacement at any time. For information about Blue Sea Systems Engine Starting Standard, go to www.bluesea.com. * Reducing cable sizes will reduce current ratings Blue Sea Systems Inc. 425 Sequoia Drive Bellingham, WA 98226 USA p .360.738.8230 www.bluesea.com • • • • • • • • • • • • • • • • Caution Disconnect positive battery terminal before installing. Débranchez la cosse positive de la batterie avant de l’installer. Desconecte el terminal positivo de la batería antes de la instalación. Prima di eseguire l’installazione, disconnettere il terminale positivo della batteria. Consult marine electrical professional for proper wiring application. Consultez un professionnel de l’électricité marine pour installer le câblage correctement. Consulte a un electricista marino profesional para la aplicación de alambrado apropiada. Per assicurarsi che i cavi siano correttamente collegati, rivolgersi ad un elettricista specializzato in motori marini. Installation Mount in an easily accessible location close to the batteries. Montez-le dans un endroit facilement accessible près des batteries. Monte en una ubicación fácilmente accesible cerca de la batería. Montare in un punto facilmente accessibile e vicino alle batterie. Attach one 4/0 AWG cable per terminal to meet ratings. Raccordez un câble 95mm² par cosse pour respecter les spécifications. Sujete un cable 95mm² por terminal de acuerdo a la clasificación. Attaccare un cavo 95mm² per conformarsi alle tarature. • Refer to the latest edition of NFPA 302 and/or ABYC E11 Standard for installation information. • • • • • • • • • • • • Battery cable terminals must be attached under nut. Torque 140 in-lb (15.82 N·m). Les cosses des câbles de batterie doivent être fixées sous la rondelle de sûreté et l’écrou – couple de serrage de 15,82 N·m (140 lb-po). Los terminales de los cables de batería deberán ser sujetados debajo de la tuerca y la arandela. Apriételos a una torsión de 15,82 N·m (140 lbs-pul). I terminali del cavo della batteria vanno attaccati con un dado e una rondella elastica: coppia di 15,82 N·m (140 lbs-in). Operation Turn all appliances off before turning the battery switch to OFF. Éteignez tous les appareils électriques avant de mettre l’interrupteur de batterie sur ARRÊT. Apague todos los artefactos antes de girar el interruptor de batería a APAGADO (OFF). Spegnere tutte le apparecchiature prima di muovere l’interruttore della batteria su OFF (spento). Do not switch to OFF while engine is running. Ne le mettez pas sur ARRÊT alors que le moteur tourne. No coloque el interruptor en APAGADO (OFF) mientras que el motor esté funcionando. Non muovere l’interruttore su OFF (spento) quando il motore è in moto.  Switch Mounting Options Cutout Dimension -Series Battery Switch Dimensions Battery Common Starter or other load