DAS VANTEC-118A Manual de usuario

Marca: DAS

Modelo: VANTEC-118A

Categoría: Juegos de altavoces

Tipo: Manual de usuario

Este manual también es adecuado para

VANTEC-20A / VANTEC-118A

User's Manual

Antes de utilizar el equipo, lea la sección

“Precauciones de seguridad” de este manual.

Conserve este manual para futuras consultas.

Before operating the device, please read the

“Safety precautions” section of this manual. Retain

this manual for future reference.

CONTENTS

7 - 10

6 x VANTEC-20A + 4 x VANTEC-118A

6 x VANTEC-20A + 2 x VANTEC-218A

6 x VANTEC-20A + 2 x VANTEC-118A

2 x VANTEC-20A + 2 x VANTEC-218A

INTRODUCTION

LINE DRAWINGS

12 - 18

19 - 23

AMPLIFIERS

SPECIFICATIONS

RIGGING SYSTEM

ANNEX

Description

ON / OFF

Overload indicator

Overheating

Equalisation

Low mains voltage

Current consumption

CONFIGURATIONS

Troubleshooting

Line connections: unbalanced and balanced

SAFETY PRECAUTIONS

WARRANTY

DECLARATION OF CONFORMITY

Manual del Usuario / vantec series / User’s Manual

Precauciones de Seguridad

Safety Precautions

Cajas acústicas activas / Self-powered loudspeaker enclosures

(VANTEC-20A, VANTEC-118A)

The exclamation point inside an equilateral triangle is intended to

alert the users to the presence of important operating and

ma in tenance ( se rvicing) i ns tr uc tions in the literature

accompanying the product. Heed all warnings. Follow all

instructions. Keep these instructions.

WARNING: This is a class A product. In a domestic environment this

product may cause radio interferences in which case the user may

be required to take adequate measures.

Use this product only in E1, E2, E3 or E4 environments according to

EN55103-2.

Equipo diseñado para funcionar entre 15ºC y 45ºC con una

humedad relativa máxima del 95%, con un rango de ±10% de la

tensión nominal de alimentación indicada en la etiqueta trasera

(según IEC 60065). Si debe sustituir el fusible preste atención al tipo

y rango.

Working temperature ranges from 15ºC to 45ºC with a relative

humidity of 95%, with ±10% of the rated main voltage value

indicated on the rear label (according to IEC 60065). If the fuse

needs to be replaced, please pay attention to correct type and

ratings.

No instale el aparato cerca de ninguna fuente de calor como

radiadores, estufas u otros aparatos que produzcan calor. Debe

instalarse siempre sin bloquear la libre circulación de aire por las

aletas del radiador.

Do not install near any heat sources such as radiators, heat registers,

stoves or other apparatus that produce heat. The circulation of air

through the heatsink must not be blocked.

No exponga este equipo a la lluvia o humedad. No use este aparato

cerca del agua (piscinas y fuentes, por ejemplo). No exponga el

equipo a salpicaduras ni coloque sobre él objetos que contengan

líquidos, tales como vasos y botellas. Equipo IP-20.

Do not expose this device to rain or moisture. Do not use this

apparatus near water (for example, swimming pools and fountains).

Do not place any objects containing liquids, such as bottles or

glasses, on the top of the unit. Do not splash liquids on the unit. IP-

20 equipment.

No emplace altavoces en proximidad a equipos sensibles a campos

magnéticos, tales como monitores de televisión o material

magnético de almacenamiento de datos.

Do not place loudspeakers in proximity to devices sensitive to

magnetic fields such as television monitors or data storage

magnetic material.

Este símbolo indica que el presente producto no puede ser tratado

como residuo doméstico normal, sino que debe entregarse en el

correspondiente punto de recogida de equipos eléctricos y

electrónicos.

This symbol on the product indicates that this product should not

be treated as household waste. Instead it shall be handed over to

the appicable collection point for the recycling of electrical and

electronic equipment.

El cableado exterior conectado al equipo requiere de su instalación

por una persona instruida o el uso de cables flexibles ya preparados.

The outer wiring connected to the device requires installation by an

instructed person or the use of a flexible cable already prepared.

Si el aparato es conectado permanentemente, la instalación

eléctrica del edificio debe incorporar un interruptor multipolar con

separación de contacto de al menos 3mm en cada polo.

If the apparatus is connected permanently, the electrical system of

the building must incorporate a multipolar switch with a separation

of contact of at least 3mm in each pole.

El colgado del equipo sólo debe realizarse utilizando los herrajes de

colgado recomendados y por personal cualificado. No cuelgue la

caja de las asas.

The appliance should be flown only from the rigging points and by

qualified personnel. Do not suspend the box from the handles.

Limpie con un paño seco. No use limpiadores con disolventes. Clean only with a dry cloth. Do not use any solvent based cleaners.

No existen partes ajustables por el usuario en el interior de este

equipo. Cualquier operación de mantenimiento o reparación debe

ser realizada por personal cualif icado. Es necesario el servicio

técnico cuando el equipo se haya dañado de alguna forma, como

que haya caído líquido o algún objeto en el interior del aparato, haya

sido expuesto a lluvia o humedad, no funcione correctamente, haya

recibido un golpe o su cable de red esté dañado.

No user serviceable parts inside. Refer all servicing to qualified

service personnel. Servicing is required when the apparatus has

been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture,

does not operate normally or has been dropped.

Para las cajas con vaso para trípode, la altura máxima de seguridad

desde el suelo a la base de la caja montada sobre trípode modelo

TRD-2, con pies a 55 cm del eje del trípode, es:

For enclosures with tripod socket, the maximum safety height from

floor to bottom of enclosure when mounting on a TRD-2 tripod,

with legs spread 55cm from the central pole, is:

El signo de exclamación dentro de un triángulo indica la existencia

de importantes instrucciones de operación y mantenimiento en la

documentación que acompaña al producto.

Conserve y lea todas estas instrucciones. Siga las advertencias.

ATENCIÓN: Es un producto clase A, por lo que en entornos

domésticos puede causar radio-interferencias, en cuyo caso el

usuario tendrá que tomar las medidas oportunas.

De acuerdo con EN55103-2, usar el equipo sólo en entornos E1, E2, E3

ó E4.

55 cm

VANTEC-20A ------------->150 cm

Para desconectar el dispositivo debe usar el enchufe. Desconecte

este aparato durante tormentas eléctricas, terremotos o cuando no

se vaya a emplear durante largos periodos.

To disconnect the device, you should use the mains plug. Unplug

this apparatus during lightning storms, earthquakes or when

unused for long periods of time.

No desconecte la tierra en el conector de alimentación pues es

peligroso e ilegal. Equipo de Clase I. El producto debe ser conectado

a un enchufe con toma de tierra. Sólo use este equipo con el cable

de red de alimentación adecuado para su país.

El signo del rayo con la punta de flecha, alerta contra la presencia de

voltajes peligrosos no aislados. Para reducir el riesgo de choque

eléctrico, no retire la cubierta.

Do not remove mains connector ground, it is dangerous and illegal.

Class I device. The product must be connected to a mains socket

outlet with protective earth connection. Only use this equipment

with an appropriate mains cord for your country.

The lightning and arrowhead symbol warns about the presence of

uninsulated dangerous voltage. To reduce the risk of electric shock,

do not remove the cover.

VANTEC-20A ------------->150 cm

Manual del Usuario / vantec series / User’s Manual

GARANTÍA

WARRANTY

Todos nuestros productos están garantizados por un periodo de 24

meses desde la fecha de compra.

Las garantías sólo serán válidas si son por un defecto de fabricación y

en ningún caso por un uso incorrecto del producto.

Las reparaciones en garantía pueden ser realizadas, exclusivamente,

por el fabricante o el servicio de asistencia técnica autorizado.

Otros cargos como portes y seguros, son a cargo del comprador en

todos los casos.

Para solicitar reparación en garantía es imprescindible que el

producto no haya sido previamente manipulado e incluir una fotocopia

de la factura de compra.

All our products are warrantied against any manufacturing defect for

a period of 2 years from date of purchase.

The warranty excludes damage from incorrect use of the product.

All warranty repairs must be exclusively undertaken by the factory or

any of its authorised service centers.

To claim a warranty repair, do not open or intend to repair the product.

Return the damaged unit, at shippers risk and freight prepaid, to the

nearest service center with a copy of the purchase invoice.

Manual del Usuario / vantec series / User’s Manual

DECLARACIÓN DE CONFORMIDAD

DECLARATION OF CONFORMITY

DAS Audio Group, S.L.

C/ Islas Baleares, 24 - 46988 - Pol. Fuente del Jarro - Valencia. España (Spain).

Nota: Los textos completos de la declaración de conformidad para VANTEC-

12A, VANTEC-15A, VANTEC-20A y VANTEC-215A están disponibles en

http://d.dasaudio.com/vK2D4.

Note: The full text of the declaration of conformity for VANTEC-12A, VANTEC-15A,

VANTEC-20A and VANTEC-215A is available at http://d.dasaudio.com/vK2D4.

Declara que VANTEC-118A:

Declares that VANTEC-118A:

Y es conforme a las siguientes Normas Armonizadas Europeas:

In accordance with Harmonized European Norms:

l EN 60065:2014.- Audio, video and similar electronic apparatus. Safety

requirements.

l EN 55032:2012.- Electromagnetic compatibility of multimedia

equipment. Emission requirements.

l EN 55103-2:2009.- Electromagnetic compatibility. Product family

standard for audio, video, audio-visual and entertainment lighting

control apparatus for professional use. Part 2:Immunity.

l EN 50581:2012.- Technical documentation for the assessment of

electrical and electronic products with respect to the restriction of

hazardous substances.

Cumple con los objetivos esenciales de las Directivas:

Abide by essential objectives relating Directives:

l Directiva de Baja Tensión (Low Voltage Directive) 2014/35/UE

l Directiva de Compatibilidad Electromagnética (EMC)

2014/30/UE

l Directiva RoHS 2011/65/UE

l Directiva RAEE (WEEE) 2012/19/UE

Manual del Usuario / vantec series / User’s Manual

INTRODUCTION

VANTEC-20A

– Active Curved Source Line Array

– Class D Bi-amplified 1500 Wpeak

– FIR filters for linear phase response

– 1 x DAS 12F4C + 2 x M-60 compression drivers

– Compact design with high output capabilities

– DAScontrol™ with presets and configurations

– DASlink™ wireless streaming and remote control

– +/- 13.5º variable tilt pole mount

The VANTEC-20A is an active curved source line array that incorporates an arsenal of hi-tech solutions designed to

provide the versatility needed by today’s sound hire professionals. Whether it be stacked on the VANTEC-118A

companion subwoofer, flown in a compact array, or used alone on a speaker stand, the VANTEC-20A can be used

effectively in an incredible number of applications that include corporate A/V, mid-size sound reinforcement, and

permanent installation.

Designed for use in arrays of up to 5 units, the VANTEC-20A is ideal for applications where the power and long-throw

characteristics of large line arrays are not needed. Individual units can be mounted on tripods with precise aiming

possible thanks to the variable angle pole mount which allows for 13.5º up or down tilt.

The DAScontrol™ interface allows users to easily configure the VANTEC-20A systems for use individually or in

combination with other units. Selectable high pass filter presets facilitate alignment with the VANTEC-18A and VANTEC-

118A active bass systems without external processing. Throw compensation settings and array size selection can all

be handled simply via the DAScontrol™ interface. When the VANTEC-20A is used individually, the DASlink™ APP can be

used to stream music in high definition stereo and remotely control the systems functions.

The enclosure is manufactured using Baltic birch plywood and finished with the DAS ISO-flex coating. Power is

supplied by a cutting-edge 1500 Wpeak Class D amplifier in a biamplified configuration driving a single DAS 12F4C

loudspeaker and twin M-60 compression drivers.

Features

The VANTEC-20A and VANTEC-118A, powered multifunction systems combine DAS´s reputation for performance

and reliability with the latest technological innovations offering users an unmatched level of versatility. The

exceptional characteristics of the onboard amplification, complex waveguide design and digital signal processing

provide the output and control required, allowing the vantec series to be deployed as a main system or in any

number of support applications. The easy-to-use rigging hardware and range of mounting accessories expand the

possible applications of the vantec series.

VANTEC-118A

– Active front-loaded subwoofer system

– 1 x 18″ DAS 18FW loudspeaker

– Class D amplifier 2000 Wpeak

– Digital signal processing (DSP)

– Unique “Deep-Loud” bass EQ switch

– Variable low-pass filter 80 Hz-125 Hz

– LED ON/OFF switch on backplate

– Top located pole mount socket

The VANTEC-118A is an active front loaded bass system

which has been designed specifically for use with the VANTEC-

20A curved source line array. Compact in size, the unit can be

flown in arrays or linked together in ground stacks thanks to

the rigging system which is compatible with the VANTEC-20A.

The electronics package includes a 2000 Wpeak Class D amplifier and 24-bit high-end DSP for exceptional

audio reproduction. A unique “Deep-Loud” EQ switch allows users to tailor the bass output to provide a low

subwoofer type response using the “Deep” setting or a louder hard hitting performance in the “Loud” setting. On

the rear panel, controls can be found for gain, polarity and a continually variable low-pass filter which ranges

from 80 Hz to 125 Hz. The VANTEC-118A is phase response coherent with the other Vantec series active tops such as

the VANTEC-20A offering precise alignment without the need of an external DSP.

Manual del Usuario / vantec series / User’s Manual

CONFIGURATIONS

POWER

Accessories

2TRD-6 Ring lock pole mount for use between satellite and sub system, black

Speaker cabling

SC-2 2m XLR microphone signal balanced cable

Units

2 x VANTEC-20A

2 x VANTEC-218A

Manual del Usuario / vantec series / User’s Manual

CONFIGURATIONS (cont’d)

6 x VANTEC-20A

2 x VANTEC-218A

POWER

DSP-2060A

POWER

Accessories

2AX-VT20 Rigging bumper for VANTEC-20A (max 5 u.), black

Speaker cabling

SC-1 1m XLR microphone signal balanced cable

PWCONLINK-09 0.9m powerCON “jumper” NAC3FCB cable

2PL-VT20S

Units

Processors

1DSP-2060A 2 In/6 Out fully configurable DSP, 9 full bandwidth parametric band EQ on each channel, AudioCore/DASnet equipped

Manual del Usuario / vantec series / User’s Manual

CONFIGURATIONS (cont’d)

POWER

DSP-2060A

POWER

Accessories

2AX-VT20 Rigging bumper for VANTEC-20A (max 5 u.), black

Speaker cabling

SC-1 1m XLR microphone signal balanced cable

PWCONLINK-09 0.9m powerCON “jumper” NAC3FCB cable

Units

Processors

1DSP-2060A 2 In/6 Out fully configurable DSP, 9 full bandwidth parametric band EQ on each channel, AudioCore/DASnet equipped

POWER

2PL-VT20S

2PL-VT118S

6 x VANTEC-20A

4 x VANTEC-118A

Manual del Usuario / vantec series / User’s Manual

LINE DRAWINGS

ALL DIMENSIONS IN MILLIMETERS

Front View

Right View

Left View

Bottom View

Top View

Rear View

SPECIFICATIONS

VANTEC-20A VANTEC-118A

DAS Audio Group, S.L. continuously strives to enhance its products through investigation and development. All

specifications are subject to change without prior notice.

VANTEC-20A

VANTEC-118A

MODEL

Nominal Amplifier Power

Input Type

Input Impedance

Sensitivity

Frequency Range (-10dB)

Horizontal Coverage (-6dB)

Vertical Coverage

Maximum Peak SPL at 1m

Transducer/Replacement Parts

Enclosure Geometry

Enclosure Material

Color/Finish

Rigging System

Connectors

AC Power Requirements

Dimensions (H x W x D)

Weight

Accessories

1500 Wpeak (Class D Bi-amp)

Balanced Differential Line

Line: 20kOhms

Line: 3 V (+12dBu)

63 Hz - 20 kHz

90º Nominal

15º Nominal

135 dB

LF: 1 x 12F4C/GM-12F4

HF: 2 x M-60/GM-M60N

Trapezoidal 7.5º

Birch Plywood

Black / ISO-flex Paint

Integrated in box design

INPUT: 1 x Female XLR

LOOP THRU: 1 x Male XLR

AC INPUT: 1 x PowerCon

AC OUTPUT: 1 x PowerCon

3.0A, 115V, 50 Hz/60 Hz

1.5A, 230V, 50 Hz/60 Hz

330 x 620 x 435 mm

13 x 24.4 x 17.1 in

28.6 kg (62.9 lb)

ANL-2

AX-VT20

TRD-2

TRD-6

PL-VT20S

FUN-3-VT20

2000 Wpeak

Balanced Differential Line

Line: 20kOhms

Line: 3 V (+12dBu)

35 Hz - 125 Hz

134 dB

LF: 1 x 18FW/GM-18FW

Rectangular

Birch Plywood

Black / ISO-flex Paint

Integrated in box design

INPUT: 2 x Female XLR

LOOP THRU: 2 x Male XLR

AC INPUT: 1 x PowerCon

AC OUTPUT: 1 x PowerCon

4.4A, 115V, 50 Hz/60 Hz

2.2A, 230V, 50 Hz/60 Hz

485 x 610 x 780 mm

19.1 x 24 x 30.7 in

45.2 kg (99.4 lb)

ANL-2

AX-VT20

TRD-6

PL-VT118S

FUN-2-VT118

Manual del Usuario / vantec series / User’s Manual

435

330

620

610

485

780

OUTPUT A OUTPUT B

HPF/THRU

SATELLITE X-OVER

LIMIT

SIGNAL

- +

POLARITY

CAUTION

DO NOT EXPOSE THIS EQUIPMENT

TO RAIN OR MOISTURE

RISK OF ELECTRIC SHOCK

DO NOT OPEN

LEVEL

+6-oo

LOW-PASS

125Hz

80Hz

100Hz

DAS Audio Group, S.L. (Valencia)

MADE IN SPAIN

INPUT A

INPUT B

115/230 V~ 50/60Hz 500W

AC INPUT

MAX. 6@230V / 2@115V

UNITS VANTEC-118A

AC OUTPUT

DEEP/LOUD

PRESET

www.dasaudio.com

OFF/ON

LED

VANTEC

series

Model: VANTEC-118A

AMPLIFIERS

Description: VANTEC-118A

1) INPUT connectors :

1/4” Jack+XLR combined socket-type input signal connectors. This is a balanced connector just like the LOOP THRU

connector with the following pin assignments:

1 or S =GND (ground).

2 or T =(+) Non inverted input.

3 or R =(-) Inverted input.

2) SATELLITE OUTPUT

A and B, XLR-type output signal connectors for connecting several units together and sending them all the same input

signal or filtered signal (by using THRU/HPF).

3) LIMIT:

Red LED indicates amplifier saturation. Amplifier limiter indicator lights.

4) SIGNAL:

Green LED indicates signal presence.

5) ON:

Green LED indicates that the unit is ON.

6) SUB LEVEL:

Potentiometer for adjusting the unit level.

7) AC INPUT :

Standard PowerCon NAC3FCA mains connector (inserted,

rotated and locked for ON). Only use this equipment with an

appropriate mains cord.

8) THRU/HPF :

‘SATELLITE OUTPUT’ selector to switch between full range

signal or pass filter with cut-off frequency of 100 Hz.

9) LOW-PASS CROSSOVER :

Button for adjusting the upper cut-off frequency for the

subwoofer unit. We recommend a cut-off frequency of 100 Hz

for vantec series use.

10) PHASE :

Switch for inverting the phase of the unit.

11) PRESET DEEP/LOUD

Button for switching between two types of frequency

response, DEEP or LOUD.

12) AC OUTPUT:

PowerCon NAC3FCB connector for AC loop thru allows up

to 6 units when using a 230V version (see unit’s label)). Only

use this equipment with an appropriate mains cord.

Manual del Usuario / vantec series / User’s Manual

Description: VANTEC-20A

Press the encoder to start navigation

Note: The INPUT and LOOP THRU are type XLR balanced connectors.

By default the state of the parameters shown is the following.

Keep in mind that any parameter changed in the DSP will

remain with the same value until someone changes it again.

The DAS array correction named Number Of Units is a

parameter that compensates the amount of energy in the

low-mid frequency range in the array:

By pressing the encoder (DAScontrol) the user can have

access to the menu:

Rotate the encoder to the desired choice, in this case “No.ofU”

and press to access all the options:

The available options for “No.ofU” are: 1, 2, 3, 4, 5 depending on

the size of the array. Rotate the encoder to select the option

needed and press again to confirm.

Use the same “Number Of Units” IN ALL the cabinets of your

system!

Once the input source has been connected to the amplifer´s

cabinet, the user has to check the gain structure of the

system.

Adjust level output from your processor and/or mixing

console in order to prevent INPUT CLIP (left signal meter):

As well, try to avoid excessive volume at the amplifier´s

output (right signal meter). Be sure that your gain structure is

adequate and not causing amplifier LIMIT:

Exceeding the limits may

cause damage in the system

Exceeding the limits may

cause damage in the system

ADJUSTING THE LEVELS

"N.ofU" (NUMBER OF UNITS)

AUDIO MANAGEMENT

THROW: Mid

HPF: off

+ 0dB

AUDIO MANAGEMENT

THROW: Mid

HPF: off

INPUT

CLIP

AUDIO MANAGEMENT

THROW: Mid

HPF: off

LIMIT

AUDIO MANAGEMENT

HPF: off

BACK

MAIN MENU

No.ofU: 1U

AUDIO MANAGEMENT

HPF: off

BACK

MAIN MENU

No.ofU: 1U>

Manual del Usuario / vantec series / User’s Manual

AUDIO MANAGEMENT

BACK

MAIN MENU

By pressing the enconder (DAScontrol) the user can have

access to the menu; rotate to navigate until selecting HPF:

No.ofU: 1U

HPF (High Pass Filter)

THROW

HPF: off

THROW: Mid

Press the encoder:

Rotate the encoder and press to confirm one of the

following” HPF” options: off, 63Hz,V118A, 100Hz.

User MUST enable the SAME HPF in ALL cabinets forming

the array!

In order to have more dynamic headroom in the system,

when used with subs, HPF at V118A position (with Vantec

subwoofers) or 100Hz is highly recommended.

Press the encoder and rotate it until “THROW” is shown in

the display:

Press the encoder to enter into this field.There are 5 options

available,” Long, L-Mid, Mid, Mid-S, Short”.

Manual del Usuario / vantec series / User’s Manual

MAIN MENU

WIRELESS AUDIO

STATUS: not linked

OPTIONS

CREATE A NEW LINK

BACK

AUDIO

AUDIO and CONTROL DASlink

option in your smart phone

or tablet and select the

VANTEC cabinet.

When selecting Master L

the Slave cabinet. Press

Continue and go to the other

cabinet and it in

Slave R mode:

tablet, smart phone etc.

CREATE NEW LINK

Select Mode:

Connect from your

device to:

LINK DONE!!

device to:

VANTEC-20A-089E39

Select Mode:

Waiting MASTER

in SLAVE: R mode

connection

Select Mode:

SINGLE: L+R > < MASTER: L >

< DASlink >

< MASTER: L >

CONTINUE

---- Wait a minute ----

< SLAVE: R >

SINGLE Mode Master & Slave

Adding Slave Unit

CREATE NEW LINK

Select Mode:

< SLAVE: R >

CREATE NEW LINK

Waiting MASTER

Searching for SLAVE

connection

Altea unit

---- Wait a minute ----

Master cabinet

Only Wireless Audio Wireless Audio + Control (DASLink)

Master cabinet

Phone / tablet

Master cabinet

Master & Slave cabinet

Master cabinet

Slave cabinet

The VANTEC series systems include wireless connectivity for streaming audio

and / or system´s management. By the use of the free APP DASlink users can

send audio up to 2 devices (Master + Slave) and control / monitor them changing

parameters and creating custom presets. First Step is going to the WIRELESS

Audio Sub-menu in the master cabinet:

WIRELESS CONNECTIVITY

Manual del Usuario / vantec series / User’s Manual

OPTIONS

In this sub-menu the user can configure all the non-audio

related options. Remember that in order to access each

parameter it is necessary to push the encoder:

OPTIONS MENU

OPTIONS MENU OPTIONS MENU OPTIONS MENU

OPTIONS MENU OPTIONS MENU

OPTIONS MENU

OPTIONS MENU OPTIONS MENU

OPTIONS MENU

RESET DEVICE

BACK

BACK BACK BACK

BACK BACK

RESET DEVICE

Are you sure?

BRIGHT: 0

BRIGHT: 0 BRIGHT: 0 BRIGHT: 0

STAND-BY: off

INFORMATION

NO YES

CONTRAST: 0

CONTRAST: 0 CONTRAST: 0

INFORMATION

INFORMATION INFORMATION

RESET DEVICE

RESET DEVICE RESET DEVICE

BACK

FW 3.12 DSP10 uC35

VANTEC20A

Melody V6.1.4

BRIGHT: 0 BRIGHT: +10

CONTRAST: -10 CONTRAST: +10

STAND-BY: off> STAND-BY:<5min>

This option resets the device to the following values:

No.ofU: 1U

HPF: off

THROW: Mid

STAND-BY: off

DIMMING: on

LOGO: on

MENU LOCK: off

B. User can LOCK the Display and the encoder WITH PASSWORD by enabling this option MENU LOCK: pw292

In case A to unlock just press the encoder: In case B to unlock PUSH encoder and enter the 3 digit password: 292

STAND-BY:When no signal is detected the amplifer shuts down. Time can be selected

OPTIONS MENU

OPTIONS MENU OPTIONS MENU

DIMMING: on

LOGO: on

LOGO: <on>

LOGO: on LOGO: on LOGO: on

LOGO: off > LOGO: <limit

LOGO: on

MENU LOCK: off

MENU LOCK: off>

MENU LOCK: off

MENU LOCK: off MENU LOCK: off

MENU LOCK: <on> MENU LOCK:<pw292

DIMMING: <on

DIMMING: on

DIMMING: off>

DIMMING: on DIMMING: on

DIMMING: When active the screen lowers its luminosity after a few seconds

A. User can LOCK the Display and Master Volume Control by enabling this option MENU LOCK: ON

1 1 1

THROW: Mid THROW: Mid THROW: Mid

HPF: off HPF: off HPF: off

O O O

+ 0dB + 0dB + 0dB

1U 1U 1U

LOCKED

PUSH TO UNLOCK

UNLOCKED Password: 0 0 0

Manual del Usuario / vantec series / User’s Manual

Pink Noise

Mains 230 Vrms

1/3 Power

2.2A

1.5A

VANTEC-118A

VANTEC-20A

ON / OFF

A sound system should be switched on

sequentially. Switch on the self-powered units last

in your sound system (switch on the subwoofer

before the mid-high system). Switch on the sound

sources such as CD players or turntables, then the

mixer, then the processors, and finally the self-

powered unit. If you have several units, it is

recommended t h a t you s w i tch t h em on

sequentially one at a time.

Follow the inverse order when switching off,

turning self-powered units off before any other

element in the sound system.

Disconnect the device by removing the mains

connector from the mains socket. The mains

connector and mains socket must always be freely

accessible and never covered or blocked in any

way. The mains cable can be detached from the

device by disconnecting the standard PowerCon

NC3FCA connector. Always disconnect the device

by removing the mains connector from the mains

socket before detaching the mains cable at the

PowerCon NC3FCA connector.

Power can be daisy chained via the NC3FCB

output connector (see details on product label).

IMPORTANT: Do not disconnect the unit while

in use.

Ensure that the device is disconnected from

the mains by observing that the ON LED is turned

off. Please note that the ON LED can stay on for

several seconds after the mains power has been

disconnected.

Low mains voltage

If mains voltage falls below the shutdown

voltage for the unit, it will stop playing. When

acceptable levels are regained, the unit will switch

back on automatically.

Therefore the current consumed by a 115V

version is double the 230V version to achieve the

same acoustic power level.

Normally it is enough just to let the unit cool

down after you have corrected the problem so that

the system functions properly again.

Overheating

This equipment does not normally overheat

du r i n g n ormal con d i tion s o f us e . W h en

overheating occurs, the unit protects itself. You

should then find out why and if necessary contact

an authorised dealer for technical assistance.

Equalisation

The unit does not need extreme settings of

equalisation to produce quality sound. Avoid high

levels of gain on the equalisers. Gain values above

+3 dB on a console’s EQ are not recommended.

Overload LED indicator (VANTEC-118A)

This device has an indicator (LIMIT LED) that

lights when the signal is excessive.

The indicator should not be lit continuously.

This distorts the signal (quickly fatiguing your ears)

and may damage the speakers. Therefore, it is

recommended that you never work with this LED

on; at most it should blink only occasionally.

Overload Screen indicators ( 20A)VANTEC-

In the main screen when input signal levels are

too high on the left side the meters will display

“input clip”.

If the input levels are in between the limits but

the output level gain is too much the right meter

will display “limit”.

Manual del Usuario / vantec series / User’s Manual

Troubleshooting

No sound from the unit. The input

meters in the screen do not show any

signal presence.

Full power cannot be obtained.

LIMIT message never appears in the

screen.

Sound i s d i sto r t ed. INPU T C L IP

message is shown.

Sound is distorted. LIMIT message is

displayed.

H u m o r b u z z w h e n a m i x e r i s

connected to the unit.

Hum or buzz when using lighting

controls in the same building.

The screen does not light up when the

mains connector is connected and the

power switch ON.

1 - Bad or loose AC connection to the

unit or the mains outlet.

2 - Faulty AC cable.

3 - Blown Fuse.

4 - The mains voltage is out of range.

5 - Damaged amplifier.

1 - Check your connections.

2 - Check the cables, connectors and AC

power with a suitable mains tester.

3 - Replace the blown fuse with another

of the same type and size.

4 - If the multimeter determines that

the mains voltage is out of the range

you may need the assistance of an

electrician to f ind an appropriate

solution.

5 - Contact a qualified tech service

center.

1-The console probably has unbalanced

outputs. You may be using an incorrect

unbalanced to balanced cable.

2 - The mixer and the powered speaker

are not plugged into the same mains

outlet.

3 - The audio signal cable is too long or

too close to an AC cable.

1-The audio signal cable is too long or

too close to the lighting cable.

2 - On a sound system with three phase

AC, the lighting equipment and the

unit are connected to the same phase.

1- Move the audio signal cable away

from lighting cables.Try to find out at

what point the noise is leaking into the

system.

2 - Connect the sound system to a

different phase than the lights. You may

need the help of an electrician.

1-Read the appendix of this manual to

make a correct unbalanced to balanced

cable.

2 - Connect the mixer and the unit to

the same mains outlet.

3 - Use a cable that is as short as possible

and/or move the audio signal cable

away from mains cables.

The system is overloaded and has

reached maximum power.

1 - Turn down the mixer´s output.

2 - Turn down the master output

volume in the unit.

1-T h e m ixer o r s i g n a l s o u r c e i s

distorting.

2 - The output level from the mixer is too

high.

3 - Input gain controls are set too high.

1-Turn down the mixer´s output and

check no channels are distroting.

2 -Turn down the mixer´s output.

3 - Turn down input gain controls.

1 - The signal source does not have

enough ouput level.

2 - Input gain controls are at very low

volume.

3 - Master Volume is very low.

1 - Use balanced outputs of a mixer.

Rise master ouput volume of the

source.

2 - Set up input gain controls at higher

positions.

3 - Increase Volume by turning up the

Master Volume control.

1 - The signal source is sending no signal.

2 - Input gain controls are at minimum

position.

3 - Defective cable.

4 - If Wireless Audio is connected input 1

which controls audio is at mimimum

position or Volume of the source is

muted.

1 - Check that the source is not muted

and is sending signal to the unit.

2 - Check input gain controls. Put them

at 0dB.

3 - Check that the cable from the source

to the unit is connected correctly.

Replace the cable if defective.

4 - Adjust Volume of input gain control

number one.

Manual del Usuario / vantec series / User’s Manual

Absolutely no risks should be taken with

regards to public safety. When flying enclosures

from ceiling support structures, extreme care

should be taken to assure the load bearing

capabilities of the structures so that the

installation is absolutely safe. Do not fly enclosures

from unsafe structures. Consult a certified

professional if needed. All flying accessories that

are not supplied by DAS Audio are the user's

responsibility. Use at your own risk.

The DAS VANTEC-20A incorporates structures in

each side of the enclosure. Thess ironworks are

made of steel and aluminum and are fixed with

special screws in the wood side of the two systems.

On each one of these structures there is a steel rod

with a special axis screw which allows to stack or

rig the enclosures. The angles vary from 15º to 15º

with each VANTEC-20A. This system allows for easy

and safe rigging or stacking, with safety pins.

Flyable vantec series models feature internal

steel angles, so that flying points are available.

Eyebolt flying points are factory sealed with M10

screws, which are replaced with eyebolts on the

flying points as required. Flying with eyebolts is

very economical and safe, and is specially

recommended for installations where the boxes

are permanently fixed.

To perform any operations related to flying the

system, read the present document first, and act

on the warnings and advice given. The goal is to

allow the user to become familiar with the

mechanical elements required to fly the acoustic

system, as well as the safety measures to be taken

during set-up and teardown.

Only experienced installers with adequate

knowledge of the equipment and local safety

regulations should fly speaker boxes. It is the user's

responsibility to ensure that the systems to be

flown (including flying accessories) comply with

state and local regulations.

The working load limits in this manual are the

results of tests by independent laboratories. It is

the user's responsibility to stay within safe limits. It

is the user's responsibility to follow and comply

with safety factors, resistance values, periodical

supervisions and warnings given in this manual.

Product improvement by means of research and

development is on going at DAS. Specifications are

subject to change without notice.

It is common practice to apply 5:1 safety factors

for enclosures and static elements. For slings and

elements exposed to material fatigue due to

friction and load variation the following ratios

must be met; 5:1 for steel cable slings, 4:1 for steel

chain slings and 7:1 polyester slings. Thus, an

element with a breaking load limit of 1000 kg may

be statically loaded with 200 kg (5:1 safety factor)

and dynamically loaded with 142 kg (7:1 safety

factor).

When flying a system, the working load must

be lower than the resistance of each individual

flying point in the enclosure, as well as each box.

Hanging hardware should be regularly inspected

and suspect units replaced if in doubt. This is

important to avoid injury and absolutely no risks

should be taken in this respect. It is highly

recommended that you implement an inspection

and maintenance program on flying elements,

including reports to be filled out by the personnel

that will carry out the inspections. Local

regulations may exist that, in case of accident, may

require you to present evidence of inspection

reports and corrective actions after defects were

found.

Manual del Usuario / vantec series / User’s Manual

RIGGING

Warning

Please follow the process to attach one box to

another. First, let's look at the sides of the

enclosure that we can see in the figure.

In the figure we can see the safety pin and the

lower trigger. The safety pin is housed in a holder

and the sliding attachment plate is hidden. By

placing the pin in the indicated hole, the enclosure

can be joined with the box directly above by

passing the pin through the orifice in the sliding

attachment plate of the upper box.

This rigging system is compatible with the

VANTEC-118A, making suspension from the VANTEC-

118A easy.

Moving the lower trigger up (1), releases the sliding attachment plate that will fall by its own weight (2).

When the trigger is released, it will return to its original position and the slide will remain fixed (3).

Similarly, to retract the slide we must act on the trigger as in (1) push the slide up (4), and release the

trigger (3).

To attach enclosures, place a VANTEC-20A enclosure with the attachment plates extended upon another

VANTEC-20A. Next, insert the safety pins in the hole and through the orifice of the attachment plates so that the

boxes are joined. The angle between both enclosures will be 15º.

Attention: Make sure the correct insertion of the safety pin.

Safety pin (Ø 6 mm) that

allows to hook the enclosures

The lower trigger releases

and allows to retract the attachment plates.

Manual del Usuario / vantec series / User’s Manual

15º

To unhook the enclosures we will act on the upper pins of the lower box as indicated below:

First we remove the pins (1) on each side. Now, we reposition the pins in the holders (2). We can now

separate the enclosures (3). Finally, we retract the attachment plates as indicated on the previous page.

AX-VT20

The rigging frame AX-VT20 is suitable for hanging a

maximum of 5 units of VANTEC-20A. It has 11 pick-up points

for the lifting slings, numbered from front to back (see

attached figure). To assure the vertical inclination of the

entire column use the Ease Focus software, which will

indicate which holes have to be used. This frame will be

joined to the first box of the column as if it were another

enclosure and will be locked with safety pins. The other

enclosures will be joined below it as indicated.

IMPORTANT SAFETY WARNING

Maximum number with AX-VT20:

5 VANTEC-20A-----0 VANTEC-118A

4 VANTEC-20A-----2 VANTEC-118A

3 VANTEC-20A-----3 VANTEC-118A

2 VANTEC-20A-----3 VANTEC-118A

1 VANTEC-20A-----4 VANTEC-118A

0 VANTEC-20A-----4 VANTEC-118A

Manual del Usuario / vantec series / User’s Manual

AX-VT20

nº1

nº11

TRD-2 and TRD-6

The VANTEC-20A unit has a tripod socket on its

underside that allows a box angle between + 25º

and -10º when placed on a TRD-2 tripod or on a TRD-6

pole. It is only possible to use one unit in this way.

The VANTEC-118A and VANTEC-218A enclosures

have a socket for a TRD-6 pole.

Example of VANTEC-20A on VANTEC-218A with TRD-6

Manual del Usuario / vantec series / User’s Manual

TRD-6

TRD-2

VANTEC-218A

VANTEC-20A

7.5º

25º

-10º

PL-VT20S

The PL-VT20S platform with WLL = 90 kgf allows

transport of up to 3 stacked units of VANTEC-20A.

Its stacked configuration requires that the

lower enclosure be secured by safety pins by

inserting the sliding attachment plates into the

slots on the platform. The other boxes will be

joined by using the rigging system.

PL-VT118S

The PL-VT118S platform with WLL = 150 kgf

allows transport of up to 3 stacked units of VANTEC-

118A. It is necessary to be very careful when moving

the assembly since the enclosures are not

attached to the platform by pins. One VANTEC-118A

can be attached to another.

PL-VT20S

PL-VT118S

Safety

Manual del Usuario / vantec series / User’s Manual

ANNEX : Line connections: unbalanced and balanced

There are two basic ways to transport an audio signal with microphone or line level:

Unbalanced line: Utilising a two conductor cable, it transports the signal as the voltage between them.

Electromagnetic interference can get added to the signal as undesired noise. Connectors that carry

unbalanced signals have two pins, such as RCA (Phono) and ¼” (6.35mm, often referred to as jack) mono. 3

pin connector such as XLR (Cannon) may also carry unbalanced signals if one of the pins is unused.

Balanced line: Utilising a three conductor cable, one of them acts as a shield against electromagnetic

noise and is the ground conductor. The other two have the same voltage with respect to the ground

conductor but with opposite signs. The noise that cannot be rejected by the shield affects both signal

conductors in the same way. At the device’s input the two signals get summed with opposite sign, so that

noise is cancelled out while the programme signal doubles in level. Most professional audio devices use

balanced inputs and outputs. Connectors that can carry balanced signal have three pins, such as XLR

(Cannon) and ¼” (6.35mm) stereo.

The graphs that follow show the recommended connection with different types of connectors to

balanced processor or amplifier inputs. The connectors on the left-hand side come from a signal source, and

the ones on the right hand side go to the inputs of the processor or amplifier. Note that on the unbalanced

connectors on the left-hand side, two terminals are joined inside the connector. If hum occurs with balanced

to balanced connections, try disconnecting the sleeve (ground) on the input connector. Note that the

illustrations show what should be connected to what, but that pin locations on an actual XLR connector are

different. Also, pin 2 hot is assumed on XLR connectors.

Manual del Usuario / vantec series / User’s Manual

UM_VT3_02_EN

www.dasaudio.com

DAS Audio of America, INC.

6900 NW 52th Street

Miami, FL. 33166 - U.S.A.

TOLL FREE: 1 888 DAS 4 USA

DAS Audio Asia PTE. LTD.

3 Temasek Avenue, Centennial

Tower #34-36

Singapore 039190

Tel. +65 6549 7760

DAS Audio Group, S.L.

C/. Islas Baleares, 24

46988 Fuente del Jarro

Valencia, SPAIN

Tel. +34 96 134 0860

DAS do Brasil LTDA.

Rua Dos Andradas, 382 SL

Santa Efigênia, São Paulo

Brasil. CEP: 01208-000

Tel. +551133330764

DAS VANTEC-118A Manual de usuario

Marca: DAS

Modelo: VANTEC-118A

Categoría: Juegos de altavoces

Tipo: Manual de usuario

Este manual también es adecuado para

Descargar PDF

informe

En otros idiomas

English: DAS VANTEC-118A User manual

DAS VANTEC-118A Manual de usuario

Este manual también es adecuado para

DAS VANTEC-118A Manual de usuario

En otros idiomas

Documentos relacionados

Otros documentos