Yamaha NY64-D El manual del propietario

Tipo
El manual del propietario

Este manual también es adecuado para

NY64-D
-
1
-
EnglishDeutschFrançais
Español
Português
Italiano
Русский
Owner’s Manual
Bedienungsanleitung
Mode d’emploi
Manual de instrucciones
Manual do Proprietário
Manuale di istruzioni
Руководство пользователя
JA
ES
KO
RU
IT
PT
FR
DE
EN
NY64-D
AUDIO INTERFACE CARD
Owner’s Manual
NY64-D
-
2
-
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT
MODIFY THIS UNIT!
This product, when installed as indicated
in the instructions contained in this man-
ual, meets FCC requirements. Modifica-
tions not expressly approved by Yamaha
may void your authority, granted by the
FCC, to use the product.
2. IMPORTANT: When connecting this
product to accessories and/or another
product use only high quality shielded
cables. Cable/s supplied with this product
MUST be used. Follow all installation
instructions. Failure to follow instructions
could void your FCC authorization to use
this product in the USA.
3. NOTE: This product has been tested
and found to comply with the
requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices.
Compliance with these requirements
provides a reasonable level of assurance
that your use of this product in a
residential environment will not result in
harmful interference with other electronic
devices. This equipment generates/uses
radio frequencies and, if not installed and
used according to the instructions found
in the users manual, may cause
interference harmful to the operation of
other electronic devices. Compliance with
FCC regulations does not guarantee that
interference will not occur in all
installations. If this product is found to be
the source of interference, which can be
determined by turning the unit “OFF” and
“ON”, please try to eliminate the problem
by using one of the following measures:
Relocate either this product or the device
that is being affected by the interference.
Utilize power outlets that are on different
branch (circuit breaker or fuse) circuits or
install AC line filter/s.
In the case of radio or TV interference,
relocate/reorient the antenna. If the
antenna lead-in is 300 ohm ribbon lead,
change the lead-in to co-axial type cable.
If these corrective measures do not
produce satisfactory results, please
contact the local retailer authorized to
distribute this type of product. If you can
not locate the appropriate retailer, please
contact Yamaha Corporation of America,
Electronic Service Division, 6600
Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to
those products distributed by Yamaha
Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)
Owner’s Manual
NY64-D
-
3
-
This applies only to products distributed by Yamaha Canada Music Ltd.
Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.
(can_b_01)
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620
Telephone : 714-522-9011
Type of Equipment : Audio Interface Card
Model Name : NY64-D
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may cause
undesired operation.
See user manual instructions if interference to radio reception is suspected.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA (FCC DoC)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
-
4
-
Owner’s Manual
NY64-D
-
5
-
Owner’s Manual
NY64-D
Table of contents
Included items........................................................................................................ 5
Precautions............................................................................6
Introduction .......................................................................... 9
Main features ......................................................................................................... 9
Updating the firmware ........................................................................................... 9
Card installation ..................................................................................................... 9
Dante support........................................................................................................ 9
Device features ....................................................................10
How to read the [SYNC] indicators ...................................... 11
Specifications.......................................................................13
General Specifications .......................................................................................... 13
Dimensions .......................................................................................................... 14
Included items
Owner's Manual (this document)
Dante Virtual Soundcard license code
Information for Users on Collection and Disposal of Old Equipment
This symbol on the products, packaging, and/or accompanying documents
means that used electrical and electronic products should not be mixed with
general household waste. For proper treatment, recovery and recycling of old
products, please take them to applicable collection points, in accordance with
your national legislation and the Directives 2002/96/EC.
By disposing of these products correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please
contact your local municipality, your waste disposal service or the point of sale
where you purchased the items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment, please contact your
dealer or supplier for further information.
[Information on Disposal in other Countries outside the European Union]
This symbol is only valid in the European Union. If you wish to discard these
items, please contact your local authorities or dealer and ask for the correct
method of disposal.
(weee_eu_en_01)
-
6
-
Owner’s Manual
NY64-D
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe place for future reference.
Always follow the basic precautions listed below to avoid the possibility of
serious injury or even death from electrical shock, short-circuiting, damages,
fire or other hazards. These precautions include, but are not limited to, the
following:
Before installing the card in a device, check to make sure that the device is compatible
with the card. Also, do not install the card in any Yamaha products not specified by
Yamaha for use with the card in order to avoid possible electrical shock, fire, or device
damage. Please check possible restrictions regarding the maximum number of Yamaha
and third-party expansion cards that can be simultaneously installed. Refer to the
owner’s manual supplied with the device, and/or the Yamaha Pro Audio web site at:
http://www.yamahaproaudio.com/
Do not attempt to disassemble or modify the card. Do not apply excessive force to card
connectors or other card components. Mishandling of the card may lead to shock, fire
hazard, or device failure.
Be sure to disconnect the power cable of the host device before installing the card and
connecting/disconnecting the cables (in order to eliminate shock hazard, undesired
noise, and avoid device damage).
Turn off all peripheral devices connected to the host device before installation, and
unplug all related cables.
WARNING
PACARD_en_1 1/3
-
7
-
Owner’s Manual
NY64-D
PACARD_en_1 2/3
Always follow the basic precautions listed below to avoid the possibility of
physical injury to you or others, or damage to the device or other property.
These precautions include, but are not limited to, the following:
Be sure to properly ground the host device to prevent electrical shock and/or
malfunction.
Do not touch the metallic leads (pins) of the circuit board when handling the card. The
pins are sharp and may cause hand cuts.
Wear a pair of heavy gloves during installation to avoid scratching or cutting your hands
on sharp edges.
NOTICE
To avoid the possibility of malfunction/ damage to the product, damage to data, or
damage to other property, follow the notices below.
Handling and maintenance
Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or
other electric devices. Otherwise, the device, TV, or radio may generate noise.
Do not expose the device to excessive dust or vibration, or extreme cold or heat (such as in
direct sunlight, near a heater, or in a car during the day), in order to prevent the possibility
of panel disfiguration, unstable operation, or damage to the internal components.
Do not place vinyl, plastic or rubber objects on the device, since this might discolor the
panel.
When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents,
cleaning fluids, or chemical-impregnated wiping cloths.
Condensation can occur in the device due to rapid, drastic changes in ambient
temperature—when the device is moved from one location to another, or air
conditioning is turned on or off, for example. Using the device while condensation is
present can cause damage. If there is reason to believe that condensation might have
occurred, leave the device for several hours without turning on the power until the
condensation has completely dried out.
Drain all static electricity from your clothing and body before handling the card.
Static electricity can damage the card. Touch an exposed metal part of the host device
or other grounded object beforehand.
Do not drop screws or other small parts inside the card. If power is applied while screws
or similar metal objects are loose inside the unit the card may malfunction or be
damaged. If you cannot retrieve dropped objects yourself, refer the problem to qualified
Yamaha service personnel.
CAUTION
Yamaha cannot be held responsible for damage caused by improper use or
modifications to the device, or data that is lost or destroyed.
-
8
-
Owner’s Manual
NY64-D
Information
About this manual
The illustrations as shown in this manual are for instructional purposes only.
The company names and product names in this manual are the trademarks or
registered trademarks of their respective companies.
Software may be revised and updated without prior notice.
European models
Purchaser/User Information specified in EN55103-2:2009.
Conforms to Environments: E1, E2, E3 and E4
PACARD_en_1 3/3
-
9
-
Owner’s Manual
NY64-D
Introduction
Thank you for purchasing the Yamaha NY64-D audio interface card. The NY64-D is a
digital audio interface card designed for use with NY card form factor card slots, and
supports the Dante gigabit Ethernet digital audio network.
In order to take full advantage of this product's features, and to enjoy years of trouble-free
use, please read this document before you begin using the product. After you have read
this document, please keep it in a safe place.
Main features
Supports 64 inputs and 64 outputs of 32-bit, 48 kHz uncompressed digital audio signals
In addition to simple daisy chaining, supports redundant connections through its
primary and secondary data paths
Features various indicators that indicate status and errors
Updating the firmware
The Dante firmware contained in this product can be updated to take advantage of new
features, feature improvements, and bug fixes.
Details about updating the firmware are available online.
http://www.yamahaproaudio.com/
For information about updating and setting up the console, please refer to the firmware
update guide available on the website.
Card installation
When inserting or removing this card, refer to the operating instructions included with the
other device for instructions and safety information.
Dante support
This product uses the Dante digital audio network protocol to send and receive audio
signals. Dante is a protocol developed by Audinate that is designed to deliver multichannel
audio signals at various sampling and bit rates, as well as device control signals over a
Gigabit Ethernet network.
For information about Dante, please visit the Audinate website.
http://www.audinate.com/
You can also find information about Dante and Dante-compatible products on the Yamaha
Pro Audio website.
http://www.yamahaproaudio.com
NOTE
When updating this product's Dante module firmware, make sure you also update the Dante module
firmware contained in other connected devices.
-
10
-
Owner’s Manual
NY64-D
Device features
1 [PRIMARY] and [SECONDARY] connectors
etherCON CAT5 connector that connects the card to a Dante audio network. Uses
an RJ-45 connector.
Supports star and daisy-chain arrangements.
2 [LINK/ACT] indicators
Flash in green when the corresponding PRIMARY or SECONDARY connector is
sending or receiving data.
3 [1G] indicators
Indicate the connection status of the PRIMARY and SECONDARY connectors. If an
indicator is lit, the corresponding connector is connected to a Gigabit Ethernet
network. If an indicator is not lit, there is a problem with the connection. In this
case, check all network cables and switches. If you cannot resolve the problem,
please contact your nearest Yamaha representative.
4 [SYNC] indicators
Indicate the status of the Dante clock sync.
When the green indicator is lit, the device that this card is installed in is the clock
slave, and the clock is in sync.
When the green indicator is flashing, the device that this card is installed in is the clock master.
When the card is turned on, the green indicator should either light or flash; if the
indicator does not light or flash, an error has occurred.
NOTE
To avoid electromagnetic interference, use shielded twisted-pair (STP) cables that are rated
at CAT5e or higher. Use conductive tape or comparable means to make sure that the metal
parts of the cable plugs are electrically connected to the STP cable shield.
We recommend using RJ-45 plugs that are compatible with Neutrik etherCON CAT5
connectors. You can also use cables with standard RJ-45 plugs.
The maximum length of cable that can be used varies depending on the type of cable. When using
CAT5e cables, data can be sent between devices that are connected by up to 100 m of cable.
մ
ձճղձճղ
-
11
-
Owner’s Manual
NY64-D
How to read the [SYNC] indicators
You can use the [SYNC] indicators to confirm the card's status.
The indicators can relay operational status, and error status.
Operational status
The [SYNC] indicators light as follows when the card is operating normally.
Error status
The [SYNC] indicators light as follows when an error has occurred.
Refer to the "Solution" information for ways to resolve the error.
[SYNC] indicators Description Meaning
Sync in progress. The card is syncing with the
Dante network. Wait until the
card is in sync. (This may take
up to 45 seconds.)
Clock master, functioning
normally.
The card is functioning as the
clock master.
Clock slave, functioning
normally.
The card is functioning as the
clock slave and is in sync.
[SYNC] indicators Description Solution
Clock settings are incorrect. Either turn on the TF series
console's Quick Config feature,
or check the clock master and
sampling frequency settings of
the Dante Controller.
Card not connected to Dante
network.
Make sure the cables are not
damaged and that they are
connected properly.
LitOff
Flashing Off
Lit
Off
FlashingOff
Flashes 2 timesOff
How to read the [SYNC] indicators
-
12
-
Owner’s Manual
NY64-D
* When the connected device is the clock master, the green indicator flashes; when it is
the clock slave, the green indicator lights.
Cable wiring is wrong; cannot
find other Dante devices.
Check the wiring of the
Ethernet cables.
Device that is not Gigabit
Ethernet compatible is
connected.
To use Dante to send and
receive digital audio, make
sure your devices are Gigabit
Ethernet compatible.
When using a redundancy
network, [SECONDARY]
connector is sending/receiving
audio.
Check the connections of the
network connected to the
[PRIMARY] connector.
When using a redundancy
network, error was detected on
the [SECONDARY] connector.
Check the connections of the
network connected to the
[SECONDARY] connector.
[SYNC] indicators Description Solution
Flashes 3 timesOff
LitLit or flashing
FlashingLit or flashing
Flashes 2 timesLit or flashing
-
13
-
Owner’s Manual
NY64-D
Specifications
General Specifications
Sampling Frequency
Temperature Range
Digital input/output specifications
Dimensions (W x H x D) & Net weight
100(W) x 38.5(H) x 132.5(D) mm, 0.2kg
* The contents of this manual apply to the latest specifications as of the printing date. To obtain
the latest manual, access the Yamaha website then download the manual file.
* Der Inhalt dieser Bedienungsanleitung gilt für die neuesten Technischen Daten zum Zeitpunkt
der Drucklegung. Um die neueste Version der Anleitung zu erhalten, rufen Sie die Website
von Yamaha auf und laden Sie dann die Datei mit der Bedienungsanleitung herunter.
* Le contenu de ce mode d’emploi s’applique aux dernières caractéristiques techniques
connues à la date d’impression du manuel. Pour obtenir la version la plus récente du manuel,
accédez au site Web de Yamaha puis téléchargez le fichier du manuel concerné.
* El contenido de este manual es aplicable a las últimas especificaciones en la fecha de impresión.
Para obtener el último manual, acceda al sitio web de Yamaha y descargue el archivo del manual.
* O conteúdo deste manual se aplica às especificações mais recentes a partir da data da
impressão. Para obter o manual mais recente, acesse o site da Yamaha e faça o download
do arquivo do manual.
* Il contenuto del presente manuale si applica alle ultime specifiche tecniche a partire dalla
data di stampa. Per ottenere la versione più recente del manuale, accedere al sito Web
Yamaha e scaricare il file corrispondente.
* В содержании данного руководства приведены последние на момент публикации
технические характеристики. Для получения последней версии руководства
посетите веб-сайт корпорации Yamaha и загрузите файл с руководством.
* 본 설명서의 내용은 인쇄일 현재 최신 사양을 기준으로 하고 있습니다 . 최신 설명서를 가져오려면 Yamaha
웹사이트에 접속 후 해당 설명서 파일을 다운로드받으십시오 .
Conditions Min. Typ. Max. Unit
External Clock Frequency 44.1kHz / 48kHz -200 +200 ppm
Accuracy +4.1667%/+0.1%/-0.1%/-4.0% to all of the above -200 +200 ppm
Conditions Min. Typ. Max. Unit
Temperature Range Operating temperature range 0 40 °C
Storage temperature range -20 60 °C
Terminal Format
Data length
Level Audio Connector
Primary / Secondary Dante 24 or 32bit 1000BASE-T 64ch ( NY64-D to other devices)
64ch (Other devices to NY64-D)
etherCON Cat5e
Specifications
-
14
-
Owner’s Manual
NY64-D
Dimensions
NY64-D
Unit: mm
100
38.5
132.5
126.7
5.8
For details of products, please contact your
nearest Yamaha representative or the authorized
distributor listed below.
Pour plus de détails sur les produits, veuillez-vous
adresser à Yamaha ou au distributeur le plus proche
de vous figurant dans la liste suivante.
Die Einzelheiten zu Produkten sind bei Ihrer unten
aufgeführten Niederlassung und bei Yamaha Vertragshändlern
in den jeweiligen Bestimmungsländern erhältlich.
Para detalles sobre productos, contacte su tienda
Yamaha más cercana o el distribuidor autorizado
que se lista debajo.
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Toronto, Ontario,
M1S 3R1, Canada
Tel: +1-416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena
Park, CA 90620, U.S.A.
Tel: +1-714-522-9011
MEXICO
Yamaha de México, S.A. de C.V.
Av. Insurgentes Sur 1647 Piso 9,
Col. San José Insurgentes,
Delegación Benito Juárez, México,
D.F., C.P. 03900
Tel: +52-55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Fidêncio Ramos, 302 – Cj 52 e
54 – Torre B – Vila Olímpia – CEP
04551-010 – São Paulo/SP, Brazil
Tel: +55-11-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.,
Sucursal Argentina
Olga Cossettini 1553, Piso 4 Norte,
Madero Este-C1107CEK,
Buenos Aires, Argentina
Tel: +54-11-4119-7000
VENEZUELA
Yamaha Musical de Venezuela, C.A.
AV. Manzanares,
C.C. Manzanares Plaza, Piso 4,
Oficina 0401, Baruta, Caracas,
Venezuela
Tel: +58-212-943-1877
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Edif. Torre Banco General, Piso 7,
Urbanización Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, República de
Panamá
Tel: +507-269-5311
THE UNITED KINGDOM/
IRELAND
Yamaha Music Europe GmbH (UK)
Sherbourne Drive, Tilbrook,
Milton Keynes, MK7 8BL, U.K.
Tel: +44-1908-366700
GERMANY
Yamaha Music Europe GmbH
Siemensstrasse 22-34,
25462 Rellingen, Germany
Tel: +49-4101-303-0
SWITZERLAND/
LIECHTENSTEIN
Yamaha Music Europe GmbH,
Rellingen, Branch Switzerland in
Zürich
Seefeldstrasse 94, 8008 Zürich,
Switzerland
Tel: +41-44-3878080
AUSTRIA/BULGARIA
Yamaha Music Europe GmbH
Branch Austria
Schleiergasse 20, 1100 Wien, Austria
Tel: +43-1-60203900
CZECH REPUBLIC/
HUNGARY/ROMANIA/
SLOVAKIA/SLOVENIA
Yamaha Music Europe GmbH
Branch Austria
Schleiergasse 20, 1100 Wien, Austria
Tel: +43-1-60203900
POLAND/LITHUANIA/
LATVIA/ESTONIA
Yamaha Music Europe GmbH
Sp.z o.o. Oddzial w Polsce
ul. Wrotkowa 14, 02-553 Warsaw,
Poland
Tel: +48-22-880-08-88
MALTA
Olimpus Music Ltd.
Valletta Road, Mosta MST9010,
Malta
Tel: +356-2133-2093
NETHERLANDS/BELGIUM/
LUXEMBOURG
Yamaha Music Europe Branch
Benelux
Clarissenhof 5b, 4133 AB Vianen,
The Netherlands
Tel: +31-347-358040
FRANCE
Yam aha M us i c Eu ro pe
7 rue Ambroise Croizat,
Zone d'activités de Pariest,
77183 Croissy-Beaubourg, France
Tel: +33-1-6461-4000
ITALY
Yamaha Music Europe GmbH,
Branch Italy
Viale Italia 88, 20020,
Lainate (Milano), Italy
Tel: +39-02-93577-1
SPAIN/PORTUGAL
Yamaha Music Europe GmbH
Ibérica, Sucursal en España
Ctra. de la Coruna km. 17,200,
28231 Las Rozas de Madrid, Spain
Tel: +34-91-639-88-88
GREECE
Philippos Nakas S.A. The Music
House
19th klm. Leof. Lavriou 190 02
Peania – Attiki, Greece
Tel: +30-210-6686168
SWEDEN/FINLAND/
ICELAND
Yamaha Music Europe GmbH
Germany filial Scandinavia
JA Wettergrensgata 1,
400 43 Göteborg, Sweden
Tel: +46-31-89-34-00
DENMARK
Yamaha Music Denmark,
Fillial of Yamaha Music Europe
GmbH, Tyskland
Generatorvej 8C, ST. TH. ,
2860 Søborg, Denmark
Tel: +45-44-92-49-00
NORWAY
Yamaha Music Europe GmbH
Germany - Norwegian Branch
Grini Næringspark 1, 1361 Østerås,
Norway
Tel: +47-6716-7800
RUSSIA
Yamaha Music (Russia) LLC.
Room 37, entrance 7, bld. 7,
Kievskaya street, Moscow, 121059,
Russia
Tel: +7-495-626-5005
NORTH AMERICA
CENTRAL &
SOUTH AMERICA
EUROPE
OTHER EUROPEAN
COUNTRIES
Yamaha Music Europe GmbH
Siemensstrasse 22-34,
25462 Rellingen, Germany
Tel: +49-4101-3030
Yam ah a M us ic G u l f F ZE
JAFZA-16, Office 512,
P.O.Box 17328,
Jebel Ali FZE, Dubai, UAE
Tel: +971-4-801-1500
TURKEY
Yamaha Music Europe GmbH
Merkezi Almanya Türkiye
İstanbul Şubesi
Maslak Meydan Sodak,
Spring Giz Plaza Bagimsiz Böl. No:3,
Sanyer Istanbul, Turkey
Tel: +90-212-999-8010
CYPRUS
Yamaha Music Europe GmbH
Siemensstrasse 22-34,
25462 Rellingen, Germany
Tel: +49-4101-303-0
OTHER COUNTRIES
Yam ah a M us ic G u l f F ZE
JAFZA-16, Office 512,
P.O.Box 17328, Jebel Ali FZE,
Dubai, UAE
Tel: +971-4-801-1500
THE PEOPLE’S REPUBLIC
OF CHINA
Yamaha Music & Electronics
(China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu,
Jingan-qu, Shanghai, China
Tel: +86-400-051-7700
INDIA
Yamaha Music India Private
Limited
Spazedge Building, Ground Floor,
Tower A, Sector-47,
Gurgaon- Sohna Road,
Gurgaon-122002, Haryana, India
Tel: +91-124-485-3300
INDONESIA
PT. Yamaha Musik Indonesia
(Distributor)
Yamaha Music Center Bldg. Jalan
Jend. Gatot Subroto Kav. 4,
Jakarta 12930, Indonesia
Tel: +62-21-520-2577
KOREA
Yamaha Music Korea Ltd.
8F, Dongsung Bldg. 21,
Teheran-ro 87-gil, Gangnam-gu,
Seoul, 135-880, Korea
Tel: +82-2-3467-3300
MALAYSIA
Yamaha Music (Malaysia) Sdn. Bhd.
No.8, Jalan Perbandaran,
Kelana Jaya, 47301
Petaling Jaya, Selangor, Malaysia
Tel: +60-3-78030900
SINGAPORE
Yamaha Music (Asia) Private
Limited
Block 202 Hougang Street 21,
#02-00, Singapore 530202,
Singapore
Tel: +65-6740-9200
TAIWAN
Yamaha Music & Electronics
Taiwan Co.,Ltd.
2F., No.1, Yuandong Rd. Banqiao Dist.
New Taipei City 22063, Taiwan
Tel: +886-2-7741-8888
THAILAND
Siam Music Yamaha Co., Ltd.
3, 4, 15, 16th Fl.,
Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330,
Thailand
Tel: +66-2215-2622
VIETNAM
Yamaha Music Vietnam
Company Limited
15th Floor, Nam A Bank Tower,
201-203 Cach Mang Thang Tam St.,
Ward 4, Dist.3,
Ho Chi Minh City, Vietnam
Tel: +84-8-3818-1122
OTHER ASIAN COUNTRIES
Yam aha C orp ora tio n
Sales & Marketing Division
10-1, Nakazawa-cho, Naka-ku,
Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street,
Southbank,
Vic. 3006, Australia
Tel: +61-3-9693-5111
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC
OCEAN
Yam aha C orp ora tio n
Sales & Marketing Division
10-1, Nakazawa-cho, Naka-ku,
Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
AFRICA
MIDDLE EAST
ASIA
OCEANIA
HEAD OFFICE Yamaha Corporation, Audio Products Sales and Marketing Division
10-1, Nakazawa-cho, Naka-ku, Hamamatsu, Japan 430-8650
PA41

Transcripción de documentos

English Deutsch Français NY64-D EN DE FR ES PT IT RU KO JA 取扱説明書 -1- NY64-D 取扱説明書 日本語 Owner’s Manual Bedienungsanleitung Mode d’emploi Manual de instrucciones Manual do Proprietário Manuale di istruzioni Руководство пользователя Русский Italiano Português Español AUDIO INTERFACE CARD FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. NY64-D Owner’s Manual -2- (class B) COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party : Yamaha Corporation of America Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620 Telephone : 714-522-9011 Type of Equipment : Audio Interface Card Model Name : NY64-D This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA (FCC DoC) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3 (B)/NMB-3(B) • This applies only to products distributed by Yamaha Canada Music Ltd. • Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée. (can_b_01) -3- NY64-D Owner’s Manual NY64-D Owner’s Manual -4- Table of contents Included items........................................................................................................ 5 Precautions............................................................................ 6 Introduction .......................................................................... 9 Main features ......................................................................................................... 9 Updating the firmware ........................................................................................... 9 Card installation ..................................................................................................... 9 Dante support ........................................................................................................ 9 Device features .................................................................... 10 How to read the [SYNC] indicators ...................................... 11 Specifications....................................................................... 13 General Specifications .......................................................................................... 13 Dimensions .......................................................................................................... 14 Included items • Owner's Manual (this document) • Dante Virtual Soundcard license code Information for Users on Collection and Disposal of Old Equipment This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC. By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. [For business users in the European Union] If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. [Information on Disposal in other Countries outside the European Union] This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. (weee_eu_en_01) -5- NY64-D Owner’s Manual PACARD_en_1 1/3 PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: • Before installing the card in a device, check to make sure that the device is compatible with the card. Also, do not install the card in any Yamaha products not specified by Yamaha for use with the card in order to avoid possible electrical shock, fire, or device damage. Please check possible restrictions regarding the maximum number of Yamaha and third-party expansion cards that can be simultaneously installed. Refer to the owner’s manual supplied with the device, and/or the Yamaha Pro Audio web site at: http://www.yamahaproaudio.com/ • Do not attempt to disassemble or modify the card. Do not apply excessive force to card connectors or other card components. Mishandling of the card may lead to shock, fire hazard, or device failure. • Be sure to disconnect the power cable of the host device before installing the card and connecting/disconnecting the cables (in order to eliminate shock hazard, undesired noise, and avoid device damage). • Turn off all peripheral devices connected to the host device before installation, and unplug all related cables. NY64-D Owner’s Manual -6- PACARD_en_1 2/3 CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: • Be sure to properly ground the host device to prevent electrical shock and/or malfunction. • Do not touch the metallic leads (pins) of the circuit board when handling the card. The pins are sharp and may cause hand cuts. • Wear a pair of heavy gloves during installation to avoid scratching or cutting your hands on sharp edges. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed. NOTICE To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below. Handling and maintenance • Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the device, TV, or radio may generate noise. • Do not expose the device to excessive dust or vibration, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day), in order to prevent the possibility of panel disfiguration, unstable operation, or damage to the internal components. • Do not place vinyl, plastic or rubber objects on the device, since this might discolor the panel. • When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths. • Condensation can occur in the device due to rapid, drastic changes in ambient temperature—when the device is moved from one location to another, or air conditioning is turned on or off, for example. Using the device while condensation is present can cause damage. If there is reason to believe that condensation might have occurred, leave the device for several hours without turning on the power until the condensation has completely dried out. • Drain all static electricity from your clothing and body before handling the card. Static electricity can damage the card. Touch an exposed metal part of the host device or other grounded object beforehand. • Do not drop screws or other small parts inside the card. If power is applied while screws or similar metal objects are loose inside the unit the card may malfunction or be damaged. If you cannot retrieve dropped objects yourself, refer the problem to qualified Yamaha service personnel. -7- NY64-D Owner’s Manual PACARD_en_1 3/3 Information About this manual • The illustrations as shown in this manual are for instructional purposes only. • The company names and product names in this manual are the trademarks or registered trademarks of their respective companies. • Software may be revised and updated without prior notice. European models Purchaser/User Information specified in EN55103-2:2009. Conforms to Environments: E1, E2, E3 and E4 NY64-D Owner’s Manual -8- Introduction Thank you for purchasing the Yamaha NY64-D audio interface card. The NY64-D is a digital audio interface card designed for use with NY card form factor card slots, and supports the Dante gigabit Ethernet digital audio network. In order to take full advantage of this product's features, and to enjoy years of trouble-free use, please read this document before you begin using the product. After you have read this document, please keep it in a safe place. Main features • Supports 64 inputs and 64 outputs of 32-bit, 48 kHz uncompressed digital audio signals • In addition to simple daisy chaining, supports redundant connections through its primary and secondary data paths • Features various indicators that indicate status and errors Updating the firmware The Dante firmware contained in this product can be updated to take advantage of new features, feature improvements, and bug fixes. Details about updating the firmware are available online. http://www.yamahaproaudio.com/ For information about updating and setting up the console, please refer to the firmware update guide available on the website. NOTE When updating this product's Dante module firmware, make sure you also update the Dante module firmware contained in other connected devices. Card installation When inserting or removing this card, refer to the operating instructions included with the other device for instructions and safety information. Dante support This product uses the Dante digital audio network protocol to send and receive audio signals. Dante is a protocol developed by Audinate that is designed to deliver multichannel audio signals at various sampling and bit rates, as well as device control signals over a Gigabit Ethernet network. For information about Dante, please visit the Audinate website. http://www.audinate.com/ You can also find information about Dante and Dante-compatible products on the Yamaha Pro Audio website. http://www.yamahaproaudio.com -9- NY64-D Owner’s Manual Device features ղ ձ ճ ղ ձ ճ մ 1 [PRIMARY] and [SECONDARY] connectors etherCON CAT5 connector that connects the card to a Dante audio network. Uses an RJ-45 connector. Supports star and daisy-chain arrangements. NOTE • To avoid electromagnetic interference, use shielded twisted-pair (STP) cables that are rated at CAT5e or higher. Use conductive tape or comparable means to make sure that the metal parts of the cable plugs are electrically connected to the STP cable shield. • We recommend using RJ-45 plugs that are compatible with Neutrik etherCON CAT5 connectors. You can also use cables with standard RJ-45 plugs. • The maximum length of cable that can be used varies depending on the type of cable. When using CAT5e cables, data can be sent between devices that are connected by up to 100 m of cable. 2 [LINK/ACT] indicators Flash in green when the corresponding PRIMARY or SECONDARY connector is sending or receiving data. 3 [1G] indicators Indicate the connection status of the PRIMARY and SECONDARY connectors. If an indicator is lit, the corresponding connector is connected to a Gigabit Ethernet network. If an indicator is not lit, there is a problem with the connection. In this case, check all network cables and switches. If you cannot resolve the problem, please contact your nearest Yamaha representative. 4 [SYNC] indicators Indicate the status of the Dante clock sync. When the green indicator is lit, the device that this card is installed in is the clock slave, and the clock is in sync. When the green indicator is flashing, the device that this card is installed in is the clock master. When the card is turned on, the green indicator should either light or flash; if the indicator does not light or flash, an error has occurred. NY64-D Owner’s Manual - 10 - How to read the [SYNC] indicators You can use the [SYNC] indicators to confirm the card's status. The indicators can relay operational status, and error status. Operational status The [SYNC] indicators light as follows when the card is operating normally. [SYNC] indicators Off Flashing Lit Description Meaning Sync in progress. The card is syncing with the Dante network. Wait until the card is in sync. (This may take up to 45 seconds.) Clock master, functioning normally. The card is functioning as the clock master. Clock slave, functioning normally. The card is functioning as the clock slave and is in sync. Lit Off Off Error status The [SYNC] indicators light as follows when an error has occurred. Refer to the "Solution" information for ways to resolve the error. [SYNC] indicators Off Off Description Solution Clock settings are incorrect. Either turn on the TF series console's Quick Config feature, or check the clock master and sampling frequency settings of the Dante Controller. Card not connected to Dante network. Make sure the cables are not damaged and that they are connected properly. Flashing Flashes 2 times - 11 - NY64-D Owner’s Manual How to read the [SYNC] indicators [SYNC] indicators Off Lit or flashing Lit or flashing Description Solution Cable wiring is wrong; cannot find other Dante devices. Check the wiring of the Ethernet cables. Device that is not Gigabit Ethernet compatible is connected. To use Dante to send and receive digital audio, make sure your devices are Gigabit Ethernet compatible. When using a redundancy network, [SECONDARY] connector is sending/receiving audio. Check the connections of the network connected to the [PRIMARY] connector. Flashes 3 times Lit Flashing When using a redundancy Check the connections of the network, error was detected on network connected to the the [SECONDARY] connector. [SECONDARY] connector. Lit or flashing Flashes 2 times * When the connected device is the clock master, the green indicator flashes; when it is the clock slave, the green indicator lights. NY64-D Owner’s Manual - 12 - Specifications General Specifications Sampling Frequency Conditions External Clock Max. Unit Frequency 44.1kHz / 48kHz Min. -200 +200 ppm Accuracy -200 +200 ppm Max. Unit +4.1667%/+0.1%/-0.1%/-4.0% to all of the above Typ. Temperature Range Conditions Temperature Range Min. Operating temperature range Storage temperature range Typ. 0 40 °C -20 60 °C Digital input/output specifications Terminal Format Data length Primary / Secondary Dante Level Audio Connector 24 or 32bit 1000BASE-T 64ch ( NY64-D to other devices) etherCON Cat5e 64ch (Other devices to NY64-D) Dimensions (W x H x D) & Net weight 100(W) x 38.5(H) x 132.5(D) mm, 0.2kg * この取扱説明書では、印刷時点の最新仕様で説明をしております。最新版の取扱説明書につきましては、ヤ マハウェブサイトからダウンロードしてお読みいただけますようお願いいたします。 * The contents of this manual apply to the latest specifications as of the printing date. To obtain the latest manual, access the Yamaha website then download the manual file. * Der Inhalt dieser Bedienungsanleitung gilt für die neuesten Technischen Daten zum Zeitpunkt der Drucklegung. Um die neueste Version der Anleitung zu erhalten, rufen Sie die Website von Yamaha auf und laden Sie dann die Datei mit der Bedienungsanleitung herunter. * Le contenu de ce mode d’emploi s’applique aux dernières caractéristiques techniques connues à la date d’impression du manuel. Pour obtenir la version la plus récente du manuel, accédez au site Web de Yamaha puis téléchargez le fichier du manuel concerné. * El contenido de este manual es aplicable a las últimas especificaciones en la fecha de impresión. Para obtener el último manual, acceda al sitio web de Yamaha y descargue el archivo del manual. * O conteúdo deste manual se aplica às especificações mais recentes a partir da data da impressão. Para obter o manual mais recente, acesse o site da Yamaha e faça o download do arquivo do manual. * Il contenuto del presente manuale si applica alle ultime specifiche tecniche a partire dalla data di stampa. Per ottenere la versione più recente del manuale, accedere al sito Web Yamaha e scaricare il file corrispondente. * В содержании данного руководства приведены последние на момент публикации технические характеристики. Для получения последней версии руководства посетите веб-сайт корпорации Yamaha и загрузите файл с руководством. * 본 설명서의 내용은 인쇄일 현재 최신 사양을 기준으로 하고 있습니다 . 최신 설명서를 가져오려면 Yamaha 웹사이트에 접속 후 해당 설명서 파일을 다운로드받으십시오 . - 13 - NY64-D Owner’s Manual Specifications Dimensions 5.8 126.7 (132.5) NY64-D 38.5 100 Unit: mm NY64-D Owner’s Manual - 14 - For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Toronto, Ontario, M1S 3R1, Canada Tel: +1-416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Avenue, Buena Park, CA 90620, U.S.A. Tel: +1-714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México, S.A. de C.V. Av. Insurgentes Sur 1647 Piso 9, Col. San José Insurgentes, Delegación Benito Juárez, México, D.F., C.P. 03900 Tel: +52-55-5804-0600 BRAZIL Yamaha Musical do Brasil Ltda. Rua Fidêncio Ramos, 302 – Cj 52 e 54 – Torre B – Vila Olímpia – CEP 04551-010 – São Paulo/SP, Brazil Tel: +55-11-3704-1377 ARGENTINA Yamaha Music Latin America, S.A., Sucursal Argentina Olga Cossettini 1553, Piso 4 Norte, Madero Este-C1107CEK, Buenos Aires, Argentina Tel: +54-11-4119-7000 VENEZUELA Yamaha Musical de Venezuela, C.A. AV. Manzanares, C.C. Manzanares Plaza, Piso 4, Oficina 0401, Baruta, Caracas, Venezuela Tel: +58-212-943-1877 PANAMA AND OTHER LATIN AMERICAN COUNTRIES/ CARIBBEAN COUNTRIES Yamaha Music Latin America, S.A. Edif. Torre Banco General, Piso 7, Urbanización Marbella, Calle 47 y Aquilino de la Guardia, Ciudad de Panamá, República de Panamá Tel: +507-269-5311 EUROPE THE UNITED KINGDOM/ IRELAND Yamaha Music Europe GmbH (UK) Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, U.K. Tel: +44-1908-366700 GERMANY Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany Tel: +49-4101-303-0 SWITZERLAND/ LIECHTENSTEIN Yamaha Music Europe GmbH, Rellingen, Branch Switzerland in Zürich Seefeldstrasse 94, 8008 Zürich, Switzerland Tel: +41-44-3878080 AUSTRIA/BULGARIA Yamaha Music Europe GmbH Branch Austria Schleiergasse 20, 1100 Wien, Austria Tel: +43-1-60203900 CZECH REPUBLIC/ HUNGARY/ROMANIA/ SLOVAKIA/SLOVENIA Yamaha Music Europe GmbH Branch Austria Schleiergasse 20, 1100 Wien, Austria Tel: +43-1-60203900 POLAND/LITHUANIA/ LATVIA/ESTONIA Yamaha Music Europe GmbH Sp.z o.o. Oddzial w Polsce ul. Wrotkowa 14, 02-553 Warsaw, Poland Tel: +48-22-880-08-88 MALTA Olimpus Music Ltd. Valletta Road, Mosta MST9010, Malta Tel: +356-2133-2093 NETHERLANDS/BELGIUM/ LUXEMBOURG Yamaha Music Europe Branch Benelux Clarissenhof 5b, 4133 AB Vianen, The Netherlands Tel: +31-347-358040 FRANCE Yamaha Music Europe 7 rue Ambroise Croizat, Zone d'activités de Pariest, 77183 Croissy-Beaubourg, France Tel: +33-1-6461-4000 ITALY Yamaha Music Europe GmbH, Branch Italy Viale Italia 88, 20020, Lainate (Milano), Italy Tel: +39-02-93577-1 SPAIN/PORTUGAL Yamaha Music Europe GmbH Ibérica, Sucursal en España Ctra. de la Coruna km. 17,200, 28231 Las Rozas de Madrid, Spain Tel: +34-91-639-88-88 GREECE Philippos Nakas S.A. The Music House 19th klm. Leof. Lavriou 190 02 Peania – Attiki, Greece Tel: +30-210-6686168 SWEDEN/FINLAND/ ICELAND Yamaha Music Europe GmbH Germany filial Scandinavia JA Wettergrensgata 1, 400 43 Göteborg, Sweden Tel: +46-31-89-34-00 DENMARK Yamaha Music Denmark, Fillial of Yamaha Music Europe GmbH, Tyskland Generatorvej 8C, ST. TH. , 2860 Søborg, Denmark Tel: +45-44-92-49-00 NORWAY Yamaha Music Europe GmbH Germany - Norwegian Branch Grini Næringspark 1, 1361 Østerås, Norway Tel: +47-6716-7800 RUSSIA Yamaha Music (Russia) LLC. Room 37, entrance 7, bld. 7, Kievskaya street, Moscow, 121059, Russia Tel: +7-495-626-5005 OTHER EUROPEAN COUNTRIES Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany Tel: +49-4101-3030 AFRICA Yamaha Music Gulf FZE JAFZA-16, Office 512, P.O.Box 17328, Jebel Ali FZE, Dubai, UAE Tel: +971-4-801-1500 MIDDLE EAST TURKEY Yamaha Music Europe GmbH Merkezi Almanya Türkiye İstanbul Şubesi Maslak Meydan Sodak, Spring Giz Plaza Bagimsiz Böl. No:3, Sanyer Istanbul, Turkey Tel: +90-212-999-8010 CYPRUS Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany Tel: +49-4101-303-0 OTHER COUNTRIES Yamaha Music Gulf FZE JAFZA-16, Office 512, P.O.Box 17328, Jebel Ali FZE, Dubai, UAE Tel: +971-4-801-1500 ASIA THE PEOPLE’S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co.,Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: +86-400-051-7700 PA41 INDIA THAILAND INDONESIA VIETNAM Yamaha Music India Private Limited Spazedge Building, Ground Floor, Tower A, Sector-47, Gurgaon- Sohna Road, Gurgaon-122002, Haryana, India Tel: +91-124-485-3300 PT. Yamaha Musik Indonesia (Distributor) Yamaha Music Center Bldg. Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: +62-21-520-2577 KOREA Yamaha Music Korea Ltd. 8F, Dongsung Bldg. 21, Teheran-ro 87-gil, Gangnam-gu, Seoul, 135-880, Korea Tel: +82-2-3467-3300 MALAYSIA Yamaha Music (Malaysia) Sdn. Bhd. No.8, Jalan Perbandaran, Kelana Jaya, 47301 Petaling Jaya, Selangor, Malaysia Tel: +60-3-78030900 SINGAPORE Yamaha Music (Asia) Private Limited Block 202 Hougang Street 21, #02-00, Singapore 530202, Singapore Tel: +65-6740-9200 TAIWAN Yamaha Music & Electronics Taiwan Co.,Ltd. 2F., No.1, Yuandong Rd. Banqiao Dist. New Taipei City 22063, Taiwan Tel: +886-2-7741-8888 Siam Music Yamaha Co., Ltd. 3, 4, 15, 16th Fl., Siam Motors Building, 891/1 Rama 1 Road, Wangmai, Pathumwan, Bangkok 10330, Thailand Tel: +66-2215-2622 Yamaha Music Vietnam Company Limited 15th Floor, Nam A Bank Tower, 201-203 Cach Mang Thang Tam St., Ward 4, Dist.3, Ho Chi Minh City, Vietnam Tel: +84-8-3818-1122 OTHER ASIAN COUNTRIES Yamaha Corporation Sales & Marketing Division 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2312 OCEANIA AUSTRALIA Yamaha Music Australia Pty. Ltd. Level 1, 99 Queensbridge Street, Southbank, Vic. 3006, Australia Tel: +61-3-9693-5111 COUNTRIES AND TRUST TERRITORIES IN PACIFIC OCEAN Yamaha Corporation Sales & Marketing Division 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2312 HEAD OFFICE Yamaha Corporation, Audio Products Sales and Marketing Division 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, Japan 430-8650 Yamaha Pro Audio global website: http://www.yamahaproaudio.com/ Yamaha Downloads http://download.yamaha.com/ Manual Development Department © 2015 Yamaha Corporation Published 12/2015 CRHD-A0 ZS02940
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Yamaha NY64-D El manual del propietario

Tipo
El manual del propietario
Este manual también es adecuado para