Transcripción de documentos

UCA DISC 1 DISC 2 DISC 3 DISC CHANGE DIGITAL AUDIO 3–DISC CD CHANGER PROGRAM STANDBY STANDBY /ON OPEN/CLOSE B.BOOST TIMER VOLUME PRESET/TUNING/BAND INPUT A/B/C/D/E / UP DOWN DOLBY SURROUND P R O • L O G I C MINI COMPONENT SYSTEM GX–707 DIRECTION OPEN/CLOSE AUTO REVERSE CASSETTE DECK DOLBY B NR MUSIC  Explanation of Graphical Symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. IMPORTANT Please record the serial number of this system in the space below. Model: Serial No.: The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The serial number is located on the rear of the main unit. Retain this Owner’s Manual in a safe place for future reference. SAFETY INSTRUCTIONS 1 2 Read Instructions – All the safety and operating instructions should be read before the unit is operated. 10 Power Sources – The unit should be connected to a Retain Instructions – The safety and operating instructions should be retained for future reference. 11 Power-Cord Protection – Power-supply cords should 3 Heed Warnings – All warnings on the unit and in the operating instructions should be adhered to. 4 Follow Instructions – All operating and other instructions should be followed. 5 Water and Moisture – The unit should not be used near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. 6 Carts and Stands – The unit should be used only with a cart or stand that is recommended by the manufacturer. 6A A unit and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit and cart combination to overturn. 7 Wall or Ceiling Mounting – The unit should be mounted to a wall or ceiling only as recommended by the manufacturer. 8 Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. 9 Heat – The unit should be situated away from heat sources such as radiators, stoves, or other appliances that produce heat. power supply only of the type described in the operating instructions or as marked on the unit. be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit. 12 Cleaning – The unit should be cleaned only as recommended by the manufacturer. 13 Nonuse Periods – The power cord of the unit should be unplugged from the outlet when left unused for a long period of time. 14 Object and Liquid Entry – Care should be taken so that objects do not fall into and liquids are not spilled into the inside of the unit. 15 Damage Requiring Service – The unit should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged; or B. Objects have fallen, or liquid has been spilled into the unit; or C. The unit has been exposed to rain; or D. The unit does not appear to operate normally or exhibits a marked change in performance; or E. The unit has been dropped, or the cabinet damaged. 16 Servicing – The user should not attempt to service the unit beyond those means described in the operating instructions. All other servicing should be referred to qualified service personnel. 17 Power Lines – An outdoor antenna should be located away from power lines. 18 Grounding or Polarization – Precautions should be taken so that the grounding or polarization is not defeated.  19 For US customers only: EXAMPLE OF ANTENNA GROUNDING Outdoor Antenna Grounding – If an outside antenna is connected to this unit, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. ANTENNA LEAD IN WIRE MAST GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810–20) ELECTRIC SERVICE EQUIPMENT Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. GROUNDING CONDUCTORS (NEC SECTION 810–21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H) NEC – NATIONAL ELECTRICAL CODE FCC INFORMATION (for US customers only) 1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: 2. IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. Relocate either this product or the device that is being affected by the interference. 3. NOTE : This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/ reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. We Want You Listening For A Lifetime YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.  Unpacking Déballage ● After unpacking, check that the following parts are contained. ● Après le déballage, vérifier que les pièces suivantes sont incluses. DISC 1 DISC 2 DISC 3 OPEN/CLOSE DISC CHANGE ● Front speakers ● Main unit ● Appareil principal DIGITAL AUDIO 3–DISC CD CHANGER PROGRAM STANDBY STANDBY /ON B.BOOST TIMER MUSIC ● Enceintes avant VOLUME PRESET/TUNING/BAND INPUT A/B/C/D/E / UP DOWN DOLBY SURROUND P R O • L O G I C MINI COMPONENT SYSTEM GX–707 DIRECTION OPEN/CLOSE AUTO REVERSE CASSETTE DECK DOLBY B NR POWER ● Remote control ● Télécommande 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE PRESET TIME A EDIT D ● Center speaker ● Enceinte centrale E CD / DIRECTION TAPE REC/ PAUSE — LEVEL TEST CENTER/ REAR/ DELAY PROGRAM SLEEP MUSIC INPUT VOLUME ● Rear speakers ● Enceintes arrière ● Batteries (size AA, UM/SUM-3, R6, HP-7) ● Piles (format AA, UM/SUM-3, R6, HP-7) ● Speaker cords ● Câbles d'enceintes ● Mounting brackets ● Supports de montage ● Screws ● AM loop antenna ● Vis ● Antenne-cadre AM ● Velcro strips ● Indoor FM antenna ● Bandes Velcro ● Antenne intérieure FM  Setting this system Installation de ce système 20 cm DISC 1 DISC 2 DISC 3 DISC CHANGE DIGITAL AUDIO 3–DISC CD CHANGER PROGRAM STANDBY STANDBY /ON 20 cm DISC 1 OPEN/CLOSE B.BOOST DISC 2 DISC 3 DISC CHANGE DIGITAL AUDIO 3–DISC CD CHANGER MUSIC PROGRAM STANDBY STANDBY /ON TIMER PRESET/TUNING/BAND INPUT / UP DOWN MINI COMPONENT SYSTEM GX–707 DIRECTION DIRECTION OPEN/CLOSE 1 cm A/B/C/D/E UP DOWN MINI COMPONENT SYSTEM GX–707 20 cm MUSIC VOLUME A/B/C/D/E / AUTO REVERSE CASSETTE DECK B.BOOST TIMER VOLUME PRESET/TUNING/BAND INPUT 20 cm OPEN/CLOSE OPEN/CLOSE AUTO REVERSE CASSETTE DECK DOLBY B NR 1 cm 20 cm 20 cm DOLBY B NR 20 cm 20 cm English Set this system by allowing enough spaces around and behind the main unit to assure good ventilation. Be sure not to place another unit or any object on top of the main unit to prevent the ventilation holes from being obstructed. Otherwise, it may cause fire or damage to the main unit. Caution When placing the speakers apart from the main unit, be sure to allow spaces of at least 20 cm (3-15/16”) above, behind and on both sides of the main unit. If the main unit is put inside a rack, the front of it must be fully opened. Français Installer ce système en laissant assez d’espace autour et derrière l’appareil principal pour assurer une bonne ventilation. Veiller à ne pas empiler un autre appareil ou un autre objet sur l’appareil principal afin de ne pas boucher les orifices de ventilation. Sinon, on risquerait de provoquer un incendie ou d’endommager l’appareil principal. Attention Lorsqu’on place les enceintes à une certaine distance de l’appareil principal, veiller à laisser un espace d’au moins 20 cm au-dessus, derrière et sur les deux côtés de l’appareil principal. Si l’on place l’appareil principal dans un meuble, veiller à ce que le côté avant du meuble soit grand ouvert.  Front panel Panneau avant Front panel L M DISC 1 DISC 2 N O DISC 3 DISC CHANGE OPEN/CLOSE 6 1 DIGITAL AUDIO 3–DISC CD CHANGER 4 J 3 PROGRAM STANDBY STANDBY /ON B.BOOST TIMER E MUSIC 5 D 0, P VOLUME PRESET/TUNING/BAND INPUT C F, S G, U T A/B/C/D/E / R, B Q, A UP DOWN 8 BASS 7 W TREBLE PHONES MODE DOLBY NR REC/ PAUSE AUTO/ MANUAL MEMORY RANDOM REPEAT TIMER TIME ADJ HOUR MIN ` ] DIRECTION Y [ V TIME DISPLAY H I 9 K 2 Z \ OPEN/CLOSE AUTO REVERSE CASSETTE DECK DOLBY B NR X  Amplifier/tuner Amplificateur/tuner 1 Display Panneau d'affichage 2 Remote control sensor Capteur de télécommande 3 TIMER 4 STANDBY [p. 13] 5 B. BOOST [p. 32] 6 PROGRAM [p. 35] 7 PHONES [p. 33] 8 BASS/TREBLE [p. 32] 9 Front cover Couvercle avant 0 / [p. 20, 22] A A/B/C/D/E [p. 22] B PRESET/TUNING/BAND [p. 20] C VOLUME [p. 32] D MUSIC [p. 33] E INPUT( / ) [p. 13, 20, 24, 26] TUNER → TAPE → CD ↑ ↓ AUX/MD ← VCR ← VIDEO F HOUR [p. 10, 37] G MIN [p. 10, 37] H DISPLAY [p. 10, 37] I MEMORY [p. 21, 22] TIME ADJ [p. 10] J STANDBY/ON [p. 13] K AUTO/MANUAL [p. 20] TIMER [p. 37, 38] CD player Lecteur de disque compact L Disc tray Plateau de disque [p. 13] M DISC (1, 2, 3) [p. 14] N DISC CHANGE [p. 13] Tape deck O P Q R OPEN/CLOSE [p. 13] ( / )/ ( ) [p. 15] [p. 13] S RANDOM [p. 18] T TIME [p. 18] U REPEAT [p. 17] [p. 13] Platine cassette V Tray Plateau [p. 24] W MODE [p. 24] X OPEN/CLOSE [p. 24] Y DIRECTION [p. 24] Z / [p. 25] [ [p. 24] \ [p. 24] ] REC/PAUSE [p. 26] ` DOLBY NR [p. 23, 26]  Remote control Telecommande 1 POWER POWER 7 1 9 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE PRESET TIME A EDIT D 2 0 9 3 G F M 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE PRESET TIME A EDIT D E E N I H E J K J CD / CD / L DIRECTION TAPE REC/ PAUSE 6 — LEVEL A PROGRAM 8 SLEEP TEST CENTER/ REAR/ DELAY MUSIC INPUT 4 S 5 DIRECTION B D C Q P P TAPE O REC/ PAUSE — LEVEL TEST CENTER/ REAR/ DELAY VOLUME PROGRAM SLEEP MUSIC INPUT VOLUME R  Amplifier/tuner Amplificateur/tuner 1 Transmission window 7 POWER [p. 13] 8 SLEEP [p. 38] 9 PRESET ( / ) [p. 20, 22] 0 TUNER [p. 20] A PROGRAM [p. 35] B MUSIC [p. 33] C VOLUME [p. 32] D INPUT [p. 13, 20, 24, 26] Fenêtre de transmission [p. 5] 2 Numeric buttons Touches numériques [p. 22] 3 A, B, C, D, E [p. 22] 4 TEST [p. 11] 5 CENTER/REAR/DELAY [p. 36] 6 LEVEL (–/+) [p. 36] CD player Lecteur de disque compact E Numeric buttons Touches numériques [p. 14] F TIME [p. 16] G PROG [p. 16] Tape deck TUNER → TAPE → CD ↑ ↓ AUX/MD ← VCR ← VIDEO H MODE [p. 14] I DISC SKIP [p. 14] J ( )/ ( [p. 15] ) K [p. 13] L / [p. 13] M EDIT [p. 28, 29, 30] N R. TIME [p. 28, 29, 30] Platine cassette O REC/PAUSE [p. 26] P / [p. 25] Q R [p. 24] [p. 24] S DIRECTION [p. 24]  English Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment. For the best performance, read this manual carefully. It will guide you in operating your YAMAHA product. Contents Precautions ....................................... 1 Features ............................................ 4 Preparations and connections ........ 5 Recording ....................................... 26 Basic recording ................................................. 26 Recording from CDs utilizing the EDIT function ............................ 28 Installing batteries in the remote control ............. 5 Remote control operation range ......................... 5 Setting up the speakers ...................................... 6 Connections ........................................................ 8 Setting the clock ............................................... 10 Adjusting brightness of the display ................... 10 Speaker balance adjustment ............................ 11 Operating an external unit connected to this system ........... 31 CD player operation ....................... 12 Using the built-in timer .................. 37 Basic play ......................................................... 13 To change the disc play mode .......................... 14 To select another disc ....................................... 14 To directly select the desired track .................... 14 To play the desired track (Skip) ........................ 15 To advance or reverse play rapidly (Search) .... 15 To exchange a disc (or discs) while playing (PLAYXCHANGE) ........................................ 15 Program play .................................................... 16 Repeat play ...................................................... 17 Random play .................................................... 18 Switching the time display ................................ 18 Timer play ......................................................... 37 Timer recording ................................................. 38 Sleep timer operation ....................................... 38 Various sound control ................... 32 General sound control ...................................... 32 Graphic equalizer ............................................. 33 Sound field processor ....................................... 34 Appendix ......................................... 39 Troubleshooting ................................................ 39 Specifications ................................................... 41 Tuning operation ............................ 19 Automatic tuning ............................................... 20 Manual tuning ................................................... 20 Automatic preset tuning .................................... 21 Manual preset tuning ........................................ 22 Playing back a tape ........................ 23 General information .......................................... 23 Basic operation ................................................. 24 Winding the tape ............................................... 25 Searching for the beginning of the desired selection .................................... 25 For basic source play, the following illustrations on top of the pages will help you look for the section you need. ...... CD play ...... Tape playback/recording ....... Tuning  Precautions: Read this before operating your system ■ Choose the installation location of this system carefully. Avoid placing it in direct sunlight or close to a source of heat. Also avoid locations subject to vibration and excessive dust, heat, cold or moisture. Keep it away from sources of hum such as transformers and electric motors. ■ Do not operate this system upside-down. It may overheat, possibly causing damage. ■ Never open the cabinet. If something drops into the set, contact your dealer. ■ The openings on the main unit cover assure proper ventilation of the main unit. If these openings are obstructed, the temperature inside the main unit will rise rapidly. Avoid placing objects against these openings, and install the main unit in a well-ventilated area to prevent fire or damage. ■ Always set the VOLUME control to minimum before starting an audio source play. Increase the volume gradually to an appropriate level after play has started. ■ When not planning to use this system for a long period of time (ie., vacation, etc.), disconnect the AC power plug from the wall outlet. ■ Grounding or polarization – Precautions should be taken so that the grounding or polarization of this system is not defeated. ■ Do not use force on switches, controls or connection wires. When moving the main unit, first disconnect the power plug and the wires connected to other equipments. Never pull the wire itself. ■ If an external appliance (TV, radio, etc.) interferes with the operation of this system, move the main unit away from such appliance. ■ The voltage to be used must be the same as that specified on this system. Using this system with a higher voltage than specified is dangerous and may result in a fire or other types of accidents causing damage. YAMAHA will not be held responsible for any damage resulting from use of this system with a voltage other than specified. ■ The sound level at a given volume setting depends on speaker location and other factors. Care should be taken to avoid exposure to sudden high levels of sound, which may occur when turning this system on with the volume control setting at high. Also avoid exposure to continuous high levels of sound. ■ Sudden temperature changes and storage or operation in an extremely humid environment may cause condensation inside the cabinet. Condensation can cause this system to malfunction. To eliminate condensation: • Pickup Leave the power on with no disc loaded until normal play becomes possible (about 1 hour). • Tape head Leave the power on with no tape loaded until normal playback becomes possible (about 1 hour). Note: If condensation forms on the tape head, dirt or dust may accumulate during use. • Remote control Wipe off condensation on the transmission window with a soft cloth before operating this system. ■ The carousel will turn when you open the disc tray by pressing OPEN/CLOSE; therefore, make sure the carousel stopped moving completely before you perform further operations such as placing or removing a disc from the disc tray. Otherwise, you may cause damage to your discs, or you might injure yourself. ■ Do not attempt to clean this system with chemical solvents; this might damage the finish. Use a clean, dry cloth. ■ Be sure to read the “Troubleshooting” section regarding common operating errors before concluding that this system is faulty. ■ To prevent lightning damage, disconnect the AC power plug and the antenna cable when there is an electric storm. ■ Do not plug the AC power plug to the wall socket before you finish all connections. ■ Never allow metallic items (e.g. screwdrivers, tools, etc.) to come near the tape deck’s record/playback head assembly. Doing so may not only scratch or damage the head’s mirrorsmooth finish, it may change the magnetic characteristics of the heads, causing a deterioration in reproduction performance quality. ■ Although the tape deck’s record/playback heads are of high quality with outstanding reproduction characteristics, they can get dirty through the use of old tapes or from dust accumulation over time. This can have a serious effect on reproduction quality. Clean the heads regularly with commonly available head cleaners or with cleaning solutions. E-1 English ■ To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.  Precautions: Read this before operating your system This system is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this system itself is turned off. This state is called the standby mode. In this state, this system is designed to consume a certain amount of power. Note Please check the copyright laws in your country to record from records, compact discs, radio, etc. Recording of copyright materials may infringe copyright laws. CAUTION FOR CARRYING THE MAIN UNIT Be sure not to carry or tip the main unit with discs in it. CAUTION FOR MOVING THE MAIN UNIT Before moving the main unit, first remove all discs from the disc tray and close the tray by pressing the OPEN/ CLOSE button. After you confirm that “NO DISC” lights up on the display, turn this system into the standby mode by pressing the STANDBY/ON switch, and then disconnect the power plug from the AC outlet. For Canadian Customers To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES– 003. E-2 WARNING To reduce the risk of fire or electric shock, do not expose this system to rain or moisture. To avoid electric shock, do not open the cabinet. Refer servicing to qualified personnel only. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. As the laser beam used in this unit is harmful to the eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only. Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.  Precautions: Read this before operating your system To prevent a malfunction of this system: • Do not use any nonstandard shaped disc (heart etc.) available on the market because it might damage the system. • Discs are not affected by small particles of dust or fingerprints on their playing surface, but even so they should be kept clean. Wipe by using a clean, dry cloth. Do not wipe with a circular motion; wipe straight outward from the center. • Do not use a disc with tape, seals, or paste on it. If you use such a disc, a disc may get stuck in the system, or damage to the system may result. Notes about handling discs • Always handle the disc with care so that its surface is not scratched. • Do not try to clean the disc’s surface by using any type of disc cleaner, record spray, anti-static spray or liquid, or any other chemical-based liquid because such substances might irreparably damage the disc’s surface. • Do not expose discs to direct sunlight, high temperature or high humidity for a long period of time because these might warp or otherwise damage the disc. • Discs are not subjected to wear during play, but damage to the disc surface when the disc is being handled can adversely affect the disc’s play. No! • Be sure to use a felt-tip pen or similar writing tool when writing on the label side of the disc. Do not use a ball-point pen, pencil, or other hard-tipped writing tool, as these may damage the disc and may adversely affect the disc’s play. • Do not warp discs. To play an 8-cm CD • When a disc is not currently being used, remove it from the system and store in an appropriate case. Place it in the inner recessed area of the disc tray. Do not put a normal (12-cm) CD on top of an 8-cm CD. • When removing or storing a disc, be careful not to scratch the playing surface. E-3 English NOTES ABOUT DISCS  Features General • • • CD Player 5-Speaker Multi-Channel Audio System (Two Front, One Center and Two Paralleled Rear Speakers) • • 3-Disc Carousel Type CD Changer High Power Output Front L, R: 80W + 80W (6Ω) RMS, 0.9% THD, 1 kHz Center: 80W (6Ω) RMS Output Power, 0.9% THD, 1 kHz Rear: 25W (6Ω) RMS Output Power, 0.9% THD, 1 kHz • • 20-Track Random Access Programming • Random Sequence Play 4 External Audio/Video Component Connecting Capability • • Multi-Use Timer/Sleep Timer • • • • Remote Control Capability • • Sound Field Processing (HALL and YMERSION) • 3 Preset Graphic Equalizer Modes (ROCK, POPS and JAZZ) SUBWOOFER Output for Low Frequency Expansion DOLBY PRO LOGIC and DOLBY 3 STEREO Decoding Test Tone Generator for Easier Speaker Balance Adjustment • Balance control for the left and right main speakers in DOLBY PRO LOGIC mode E-4 Repeat Play for Single Track/Entire Disc/All Discs Tape Deck • • • • Automatic Synchronized Recording with CD EDIT Function Useful for Recording CD(s) Automatic Reverse Dolby B Type Noise Reduction System Tuner BASS BOOST 5-Band Spectrum Analyzer PLAYXCHANGE Disc changing while playing • • 40 Station Preset Tuning Automatic Preset Tuning  Preparations and connections 1 Turn the remote control over and remove the battery compartment cover by sliding it in the direction of the mark. 2 Insert the batteries (AA, R6, UM-3 type) according to the 1 polarity markings on the inside of the battery compartment. 3 Attach the battery compartment cover. 3 Notes 2 • Be sure the polarities are correct. (see the illustration inside the battery compartment.) • Remove the batteries if the remote control is not used for an extended period of time. • If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. • Be sure to use the same type of batteries. • Do not use a new battery and an old battery together. Remote control operation range Notes DISC 1 DISC 2 DISC 3 DISC CHANGE • The area between the remote control and the main unit must be clear of large obstacles. • Do not expose the remote control sensor to strong lighting, in particular, an inverter type fluorescent lamp. Otherwise, the remote control may not work properly. If necessary, position the main unit away from direct lighting. OPEN/CLOSE DIGITAL AUDIO 3–DISC CD CHANGER PROGRAM STANDBY B.BOOST MUSIC STANDBY /ON TIMER VOLUME PRESET/TUNING/BAND INPUT A/B/C/D/E / UP DOWN DOLBY SURROUND P R O • L O G I C MINI COMPONENT SYSTEM GX–707 DIRECTION OPEN/CLOSE DOLBY B NR 30° 30° 0.2 m – 6 m (8” – 20’) AUTO REVERSE CASSETTE DECK Battery replacement If you find that the remote control must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones. E-5 English Installing batteries in the remote control  Preparations and connections Setting up the speakers ■ 4 channel 5 speaker configuration Center Front L Front R This system employs a 5 speaker configuration: 2 front speakers, 2 rear paralleled speakers and a center speaker. The front speakers are used for outputting main source sound. The rear speakers are for effect and surround sounds when the sound PRO LOGIC or HALL is selected. The center field program speaker is for center sounds (dialogue etc.) when the sound field program PRO LOGIC or 3 STEREO is selected. Dialogue Rear L Rear R ■ Placing the speakers Front speakers: Center Front R Center speaker: Rear speakers: (Subwoofer) Front L (TV set) Rear R Rear L Subwoofer: (not included in this system) On both sides of and at approximately the same height as the TV. Precisely between the front speakers. Behind your listening position, facing slightly inward. About 1.8 m (approx. six feet) from the floor. The position of the subwoofer is not so critical because low bass tones are not highly directional. However, we recommend that you place the subwoofer anywhere in front of your listening position. ■ Mounting the center speaker Velcro strip 1 TV set E-6 2 Place the speaker on top of the TV or on the floor under the TV or inside the TV rack so that it is stable. When placing the speaker on top of the TV, put the provided velcro strips at two corners on both the bottom of the speaker and top of the TV to prevent the speaker from falling.  Preparations and connections ■ Mounting the rear speakers 60 mm To mount the rear speakers by using commercially available speaker stands The provided mounting bracket has 1 pair of screw holes (at an interval of 60 mm). They are for mounting the speaker on a speaker stand. * These screw holes can be used with M4 screws only. Mounting bracket Note It is recommended that you connect the speaker cords to the speaker’s terminals before attaching the bracket to the speaker. 1 Attach the bracket to the bottom of the speaker by using the provided screw so that the convex part of the bracket fits in the grooved part of the speaker as shown left. 2 Mount the speaker on the speaker stand by using the screw holes on the bracket. Screw To mount the rear speakers directly on the wall Tapping screw (Available at the hardware store) 65 mm Wall or wall support Min. 12 mm If desired, you can hang the speaker on the protruding screws on the wall without using the bracket. Fasten screws into a firm wall or wall support as shown left, and hang the holes of the speaker on the protruding screws. * Make sure that the screws are securely caught by a narrow part of the holes. WARNING • Each of the rear speakers weighs 0.8 kg (1 lbs. 12 oz.). Do not mount them on thin plywood or soft wall surface material, as the screws may come out of the flimsy surface, causing the speakers to fall and be damaged, or result in personal injury. • Do not fasten the speakers to the wall with nails, adhesives, or other unstable hardware. Long-term use and vibrations may cause them to fall. • To avoid accidents resulting from tripping over loose speaker cords, fix them to the wall. • Select a proper position on the wall to mount the speaker and the stand so that no one will injure his/her head or face with the edge of the stand. E-7 English Mount the rear speakers on a shelf, rack or on the floor, or hang them on the wall.  Preparations and connections Connections Never plug the AC supply lead of this system into the AC outlet until all connections are completed. Subwoofer system (not included in this system) Center speaker Rear speaker Rear speaker L R INPUT SPEAKERS SEE OWNER'S MANUAL FOR CONNECTION. REAR R SUBWOOFER Front speakers CENTER L REAR VIDEO SIGNAL OUT MONITOR OUT L R R L OUT VCR IN CENTER : 6 REAR : 12 MIN./SPEAKER MIN./SPEAKER VIDEO OUT MAINS AUX/MD IN R FRONT L 6 MIN./SPEAKER SPEAKERS To AC outlet ■ Connecting speakers Connect the speakers to the corresponding speaker terminals on the rear of the main unit by using the speaker cords. Make sure that the polarity of the speaker cords is correct, that is the + and – markings are observed. If these cords are reversed, the sound will be unnatural and lack bass. On the speakers On the main unit Red: positive (+) Black: negative (–) Red: positive (+) Black: negative (–) 2 1 3 1Press the tab. 2Insert the bare wire. [Remove approx. 5mm (1/ 4”) insulation from the speaker wires.] 3Release the tab and secure the wire. 1 3 2 1Pull up the tab. 2Insert the bare wire. [Remove approx. 5mm (1/ 4”) insulation from the speaker wires.] 3Press down the tab and secure the wire. Caution Do not let the bare speaker wires touch each other as this could damage the amplifier and/or speakers. When connecting a subwoofer (not included in this system) You may wish to add a subwoofer to reinforce the bass frequencies. When connecting a subwoofer to this system, connect the SUBWOOFER OUT terminal of this system to the INPUT terminal of the subwoofer. * Ordinary subwoofers, including the Yamaha Active Servo Processing Subwoofer System, are designed so that both the amplifier and subwoofer are contained in the same unit. * The SUBWOOFER OUT terminal outputs low frequencies from the left front, center and right front channels. (The cut-off frequency of this terminal is 200 Hz.) E-8  Preparations and connections ■ Antenna connection (1) Supplied FM antenna ANTENNA FM 75 GND AM Connect the FM antenna wire to the corresponding terminal and direct it to the direction where the strongest signal can be received. UNBAL. (2) Supplied AM loop antenna Connect the AM loop antenna wires to the corresponding terminals. Position the AM loop antenna for optimum reception. ANTENNA FM 75 GND Notes AM • When static is still heard even after adjusting the position of the AM loop antenna, try reversing the wire connections (from the right terminal to the left one, and vice versa). • The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall. UNBAL. FREQUENCY STEP DIGITAL OUT 50 K H Z 9 KHZ OPTICAL FM AM 100 K H Z 10 K H Z (2) Using an external antenna • If you need better reception, use an external FM antenna instead of an indoor FM antenna. Consult your dealer. • Use an external AM antenna if you need better reception. Consult your dealer. ANTENNA FM 75 GND AM UNBAL. ■ Connecting external components FREQUENCY STEP DIGITAL OUT 50 K H Z 9 KHZ OPTICAL FM AM 100 K H Z 10 K H Z TV monitor SEE FOR REAR R SUBWOOFER VIDEO SIGNAL OUT MONITOR OUT R L OUT VCR IN VCR CENTER REAR : VIDEO LD/DVD player, etc. This system can be connected with external audio and video components. Make connections between this system and the components using RCA pin plug connector cables, by correctly connecting L (left) to L and R (right) to R. Also, refer to the owner’s manual for the component to be connected to this system. * A digital-to-digital recording is possible from a CD played on the built-in CD player to an MD (or tape) on an external MD recorder (or DAT) by connecting the DIGITAL OUT (OPTICAL) terminal on the rear of the main unit to the MD recorder (or DAT). OUT AUX/MD IN R MD recorder, etc. E-9 English (1)  Preparations and connections Setting the clock DISC 1 DISC 2 DISC 3 OPEN/CLOSE DISC CHANGE 1 While the power is on, press DISPLAY to display time. 2 While holding down TIME ADJ, press HOUR and set the hour. DIGITAL AUDIO 3–DISC CD CHANGER PROGRAM STANDBY STANDBY /ON B.BOOST MUSIC TIMER VOLUME PRESET/TUNING/BAND INPUT A/B/C/D/E / UP DOWN BASS TREBLE PHONES MODE DOLBY NR REC/ PAUSE AUTO/ MANUAL MEMORY RANDOM REPEAT TIMER TIME ADJ HOUR MIN TIME DISPLAY * Press HOUR once to advance the time by 1 hour. Press and hold to advance continuously. 3 While holding down TIME ADJ, press MIN and set the minute. * Press MIN once to advance the time by 1 minute. Press and hold to advance continuously. * The hour setting will not advance even if minute is advanced from “59” to “00”. DIRECTION Australia model uses a 24-hour display. U.S.A. and Canada models use a 12-hour display. For General model, either the 24hour display or the 12-hour display [shown by “AM (PM) 12:00”] is selected depending on the setting of the FREQUENCY STEP switch on the rear panel. OPEN/CLOSE AUTO REVERSE CASSETTE DECK DOLBY B NR * Set this system into the standby mode and disconnect the AC supply lead when switching the FREQUENCY STEP. DISPLAY 1 2 MEMORY RANDOM TIME ADJ REPEAT HOUR Note MIN Changes. 3 MEMORY RANDOM TIME ADJ REPEAT HOUR In the event of a power failure or when the AC supply lead is disconnected, the time display will go out; however, the clock will function for about 5 minutes without any power supply. Otherwise, the time display will flash on and off to indicate that time must be reset. MIN Changes. Adjusting brightness of the display If desired, you can adjust the brightness of the display. DISC CHANGE OPEN/CLOSE Press and hold DISPLAY for more than 2 seconds so that “DIMMER ±0” appears on the display. While holding down DISPLAY, turn VOLUME clockwise to increase or counterclockwise to decrease brightness. DIGITAL AUDIO PROGRAM B.BOOST MUSIC VOLUME UP VOLUME DOWN Y RANDOM REPEAT HOUR MIN TIME DISPLAY DISPLAY E-10 Control range: ±0 to –6 (Preset value: ±0)  Preparations and connections English Speaker balance adjustment You can adjust the sound output level balance between the front, center, and rear speakers using the built-in test tone generator. This is important for the best performance of the built-in Dolby Pro Logic surround decoder. You can adjust the sound output level of center and rear speakers from –21 to +10 and the balance of the sound output levels of the left and right front speakers from L–6 to R–6. The adjustment of each speaker output level should be done from your listening position with the remote control. Otherwise, the result may not be satisfactory. 1 Turn on the power. POWER 1 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE PRESET TIME A EDIT D 2 Turn down the volume to minimum. 3 Press PROGRAM repeatedly until “ PRO LOGIC” lights up on the sound field program indicator. 4 Press TEST. * “TEST” flashes on and off on the display. 5 Press VOLUME E to increase the volume. You will hear a test tone (like pink noise) from the left front speaker, the center speaker, the right front speaker, and then the rear speakers, for about 2.5 seconds each. The display changes as shown below. CD / DIRECTION TAPE REC/ PAUSE 6 3 — LEVEL TEST CENTER/ REAR/ DELAY PROGRAM SLEEP 4, 7 MUSIC INPUT 2, 5 * The test tone from the left rear speaker and the right rear speaker will be heard at the same time. VOLUME 6 Press LEVEL+/– to adjust the sound output level of the center speaker when “>CENTER<” is displayed. Press LEVEL+/– to adjust the sound output level of the rear speakers when “<SURROUND>” is displayed. Press LEVEL+/– to adjust the balance of the output volume level from the left and right front speakers when “LEFT<<<<” is displayed. Press + for left and – for right front speakers to compensate for the sound inbalance caused by poor speaker location or unique listening room acoustics. example) MUSIC PROGRAM PRO LOGIC CD TEST Changes. VOLUME 7 When the adjustments are finished, press TEST to cancel the test tone. * “TEST” disappears from the display. Note Once you have completed these adjustments, you can adjust the whole sound level on your audio system by using VOLUME on the main unit or the remote control. E-11  CD player operation Display information Each indicator mentioned with a number on pages 13–18 corresponds to the indicator with the same number on this page. 2 1 3 TRACK 100 350 1K 3.5K 10K MUSIC TOTAL REM PROGRAM RANDOM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OVER 15 CD 4 5 6 7 8 S F REP PROG VOLUME 9 0 1 TRACK (track number) 2 Time display 3 Disc indicator 7 Music calendar The number on the top of this indicator shows the currently selected disc. This indicator will light up when the currently selected disc has more than 15 tracks. 4 CD (input source indicator) 5 (play) 6 RANDOM E-12 Track numbers on the currently selected disc will light up (up to the number 15). 8 OVER 15 9 PROG (program) 0 (S, F) REP [(single, full) repeat]  CD player operation 4 1 Turn on the power. 2 Press INPUT or (or INPUT on the remote control) until “CD” (2) appears on the display. 3 Press DISC (1, 2, 3) STANDBY indicator DISC 1 DISC 2 4 DISC 3 DISC CHANGE OPEN/CLOSE DIGITAL AUDIO 3–DISC CD CHANGER PROGRAM STANDBY STANDBY /ON 3, 5 B.BOOST MUSIC TIMER VOLUME PRESET/TUNING/BAND INPUT A/B/C/D/E / UP DOWN BASS PHONES 1 TREBLE MODE DOLBY NR 2 REC/ PAUSE AUTO/ MANUAL MEMORY RANDOM REPEAT TIME DISPLAY / (play/pause) (stop) POWER 1 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE PRESET TIME A EDIT D OPEN/CLOSE to open the disc tray. * The carousel will turn when you open the disc tray by pressing OPEN/CLOSE; therefore, make sure the carousel stopped moving completely before you perform further operations. Otherwise, you may cause damage to your discs, or you might injure yourself. 4 Place discs on the table with label side facing upward. * Up to three discs can be loaded on the table. To load the third disc, rotate the disc table by pressing DISC CHANGE on the front panel. * 8 cm (3”) discs can be played without an adaptor. * The disc placed on the right side is played first. 5 Press OPEN/CLOSE to close the disc tray. * If the selected disc is a CD, the total number of tracks (1) and the total playing time of the disc (2) will be displayed for several seconds. * If the disc contains more than 15 tracks, the “OVER 15” indicator (8) will light up. * If the disc tray is closed by pushing the front edge of the tray, play will begin automatically. 6 Press / to begin play. To pause (stop) Press / . E To stop play CD / Press / (play/pause) DIRECTION TAPE REC/ PAUSE — LEVEL TEST CENTER/ REAR/ DELAY PROGRAM SLEEP VOLUME To finish using this system Turn this system into the standby mode by pressing STANDBY/ on the remote control). The STANDBY ON (or POWER indicator will light up and the display will go out. Direct operation MUSIC INPUT . 2 DISC (1, 2 or 3) on the front panel and / on the remote control can be used when this system is in the standby mode or another input source is selected. E-13 English Basic play  CD player operation To change the disc play mode DISC (1, 2, 3) DISC 1 DISC 2 DISC 3 DISC CHANGE OPEN/CLOSE If necessary, change the disc play mode by pressing MODE on the remote control. All disc play mode: DIGITAL AUDIO PROGRAM B.BOOST MUSIC All discs on the disc tray are played sequentially (originally set to this mode). Single disc play mode: Only the designated disc is played. Lights up only when the all disc play mode is selected. VOLUME PRESET/TUNING/BAND A/B/C/D/E / UP DOWN To select another disc ODE DOLBY NR REC/ PAUSE AUTO/ MANUAL MEMORY RANDOM REPEAT TIMER TIME ADJ HOUR MIN TIME DISPLAY Press DISC SKIP on the remote control once or more (so that the corresponding disc number comes to the top position of the disc indicator (3)). Pressing DISC (1, 2 or 3) will select the disc directly, and play will automatically begin from track 1. Numeric buttons To directly select the desired track POWER By using the numeric buttons on the remote control, any track you wish to listen to can be played directly. DISC SKIP 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE PRESET TIME A EDIT Use the numeric buttons to select the desired track. Play will begin automatically. A. For example, to choose track 5 Press 5. B. For example, to choose track 12 (1)Press +10. (2)Within a few seconds, press 2. MODE D E CD / C. For example, to choose track 20 (1)Press +10. (2)Within a few seconds, press +10 again. (3)Within a few seconds, press 0. Note If you select a track number higher than the number of tracks on the disc, the last track of the disc may be played. E-14  CD player operation DISC CHANGE DISC 1 DISC 2 DISC 3 OPEN/CLOSE DISC CHANGE To advance to the next track During play, press ( advances to other tracks. ). Pressing ( ) repeatedly To return to the beginning of current track DIGITAL AUDIO During play, press PROGRAM B.BOOST ( ) once. MUSIC To return to previous track VOLUME PRESET/TUNING/BAND A/B/C/D/E / UP DOWN S During play, press previous track. Repeatedly press ( ( ) twice in succession to return to the ) to return to other previous tracks. TREBLE MODE DOLBY NR REC/ PAUSE AUTO/ MANUAL MEMORY RANDOM REPEAT TIME DISPLAY Note / (play/pause) (Skip forward) (Search forward) (Skip backward) (Search backward) This function can also be performed while the CD player is being stopped. Press / when the desired track number appears on the track number display. Play will begin from the beginning of that track. To advance or reverse play rapidly (Search) POWER Press and hold ( ) to advance play rapidly, and ( ) to reverse play rapidly. 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE PRESET TIME A EDIT D DISC SKIP To exchange a disc (or discs) while playing (PLAYXCHANGE) E (Skip forward) (Search forward) CD / / (play/pause) During play, you can open the disc tray by pressing DISC CHANGE without interrupting play. In this case, however, pressing DISC SKIP or DISC (1, 2 or 3) is invalid. (Skip backward) (Search backward) E-15 English To play the desired track (Skip) DISC (1, 2, 3)  CD player operation DISC 1 DISC 2 DISC 3 Program play OPEN/CLOSE DISC CHANGE You can program up to 20 tracks in any desired order. 1 When the CD player is being stopped, press PROG to prepare DIGITAL AUDIO PROGRAM B.BOOST MUSIC 5 2 If necessary, select the desired disc by pressing DISC SKIP. VOLUME ET/TUNING/BAND A/B/C/D/E / UP DOWN TIME REC/ PAUSE DOLBY NR AUTO/ MANUAL MEMORY RANDOM REPEAT TIMER TIME ADJ HOUR MIN TIME DISPLAY * Just after you change the disc, the CD player reads the contents of the newly selected disc for a few seconds. If you go on to the next step during this internal operation, “WAIT” (2) appears on the display and your operation is canceled. 3 Use the numeric buttons to select the desired track number. * The selected track number (1) and the total play time of the programmed tracks (2) will light up on the display, and it will soon be replaced by the display of the next play order (2). Programmed track numbers on the selected disc will stop flashing and light up on the music calendar (7). * Pressing TIME displays the total play time of the programmed tracks (2) for about 1 second, and then it is replaced by the display of the next play order (2). POWER 3 1 2 3 1 4 2 5 3 6 4 Repeat steps 2 and 3 to program other tracks. 4 7 5 8 6 9 5 Press 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE PRESET TIME TIME for programming. * “PROG” (9) and “P-01” (2) will light up on the display, and all track numbers on the selected disc (7) will begin blinking. A EDIT D 1, E PROG 2 CD / / to start the program play. Notes • If the total time of the programmed tracks becomes 100 minutes or more, the first digit will not be displayed. • The total time of the programmed tracks will not be displayed, if track number 16 or higher is programmed. / ) can be performed during play, but only within • Skip ( the range of the programmed tracks. / ) can be performed during play to search all • Search ( tracks, including unprogrammed tracks. To cancel a programmed sequence Press 5, / (play/pause) Display information during programming Play order Selected disc TRACK VCD PBC TIMER SLEEP NOR TEST PHANTOM HALL ERSION TUNER CD MD TAPE RANDOM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OVER 15 EDIT S F REP A B PROG V Music calendar Selected track number Total playing time TRACK TOTAL M HALL MERSION E-16 VCD PBC TIMER SLEEP NOR TEST PHANTOM TUNER CD MD TAPE RANDOM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OVER 15 EDIT S F REP A B PROG V while the CD player is being stopped. To check (and correct) program data 1. Press PROG when the CD player is being stopped. 2. Every time is pressed, the track numbers and sequential order of the programmed tracks can be checked one after another. The display of the track number can be returned . (sequentially in reverse order) by pressing 3. If you want to correct the program data, press a numeric button to select the track to replace the one displayed. The previously programmed track will be cleared from the memory and the new one will be programmed. To complete the correction, press PROG or / once again.  CD player operation OPEN/CLOSE All discs, a disc, a single track or a programmed sequence can be repeated continuously. Press REPEAT once or more to select the desired repeat play mode so that the S REP or F REP indicator (0) is illuminated. DIGITAL AUDIO (off) PROGRAM B.BOOST S REP MUSIC F REP VOLUME Repeat play modes SINGLE REPEAT (S REP) UP DOWN REPEAT MEMORY RANDOM REPEAT TIME ADJ HOUR MIN TIME DISPLAY A single track is played repeatedly. * This is also available in the program play mode and the random play mode. (If the repeat play mode is switched off, the program play mode or the random play mode will be resumed.) FULL REPEAT (F REP) When the CD player is in the single disc play mode: The designated disc is played repeatedly. * In the random play mode, the selected disc is repeatedly played, but the order of tracks is different each time. /CLOSE When the CD player is in the all disc play mode: All discs on the disc tray are played repeatedly. * In the random play mode, the random play is performed among all discs and repeated with a different order of tracks each time. Note In the program play mode, a sequence of programmed tracks is played repeatedly. To cancel the repeat play Press REPEAT repeatedly until the (S, F) REP indicator (0) goes out. E-17 English Repeat play DISC CHANGE  CD player operation Random play OPEN/CLOSE DISC CHANGE Tracks on a selected disc or all discs on the disc tray can be played randomly. 1 If necessary, switch the disc play mode by pressing MODE. DIGITAL AUDIO * If the single disc play mode is selected, select the desired disc by pressing DISC SKIP. PROGRAM B.BOOST MUSIC 2 Press RANDOM to begin random play. * The “RANDOM” indicator (6) will light up. To cancel the random play VOLUME UP RANDOM DOWN Press , or press RANDOM so that the “RANDOM” indicator (6) will go out. Note This feature will not function during programming or program play. O/ UAL MEMORY RANDOM REPEAT R TIME ADJ HOUR MIN TIME DISPLAY DISC CHANGE Switching the time display OPEN/CLOSE Every time TIME is pressed, the display will change as described below. [Example] When the second track is being played: DIGITAL AUDIO PROGRAM B.BOOST The elapsed play time for the current track will be displayed. MUSIC TRACK VOLUME UP DOWN TIME TO/ NUAL MEMORY RANDOM REPEAT TIME ADJ HOUR MIN MER TIME DISPLAY The remaining play time for the current track will be displayed. TRACK REM The total play time of the disc will be displayed. POWER 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE TRACK TOTAL The total remaining play time of the disc will be displayed. TRACK PRESET TIME TIME A EDIT D E-18 E TOTAL REM  Tuning operation Each indicator mentioned with a number on pages 20–22 corresponds to the indicator with the same number on this page. 1 2 PRESET 100 350 1K 3.5K 10K MUSIC STEREO AUTO TUNED PROGRAM TUNER VOLUME MEMORY 3 4 5 6 1 Preset station group and number indicator 2 Multi-information display 3 STEREO 4 AUTO 7 5 TUNED 6 MEMORY 7 TUNER (input source indicator) E-19 English Display information  Tuning operation Automatic tuning 5, 3 DISC 1 DISC 2 DISC 3 1 Turn on the power. 2 Press INPUT or until “TUNER” (2, 7) appears on the display, or simply press TUNER on the remote control. 3–DISC CD CHANGER 1 2 3 Select the reception band (FM or AM) by pressing PRESET/ STANDBY STANDBY /ON TIMER PRESET/TUNING/BAND INPUT A/B/C/D/E / 3 BASS TREBLE PHONES MODE DOLBY NR REC/ PAUSE AUTO/ MANUAL MEMORY TIMER TIME ADJ RAN TUNING/BAND (or TUNER on the remote control), and confirm it on the display (2). * Do not select the preset tuning mode (in which “PRESET” (1) lights up on the display). 4 Press AUTO/MANUAL so that “AUTO” (4) lights up on the display. HO 5 Press 2, 4 6 If the station where tuning search stopped is not the desired one, POWER 1 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE PRESET TIME A EDIT to tune to a higher frequency, or press to tune to a lower frequency. (When tuned in to a station, “TUNED” (5) will light up on the display.) Direct operation 2 D follow step 5 again. * If the tuning search does not stop at the desired station, change to the Manual tuning method as described below. * “STEREO” (3) will light up when an FM stereo broadcast with sufficient signal strength is received. TUNER on the remote control will work if it is pressed when this system is in the standby mode or another input source is selected. Manual tuning 1 Follow steps 1–3 of the Automatic tuning method. E 2 Press AUTO/MANUAL so that “AUTO” (4) disappears from CD / the display. 3 Press and hold to tune to a higher frequency, or press and hold to tune to a lower frequency. Release the button just before reaching the desired frequency, and then press it repeatedly until the desired frequency appears. (When tuned in to a station, “TUNED” (5) will light up on the display.) DIRECTION TAPE REC/ PAUSE — LEVEL TEST Note CENTER/ REAR/ DELAY PROGRAM SLEEP If you tune in to an FM station manually, it is received in monaural to increase the signal quality. MUSIC INPUT 2 VOLUME E-20  Tuning operation DISC 1 DISC 2 You can make use of an automatic preset tuning function. With this function, the built-in tuner performs automatic tuning. Up to 40 stations [8 stations x 5 groups (A, B, C, D and E)] are stored automatically. DISC 3 3–DISC CD CHANGER 1 1 Turn on the power. STANDBY STANDBY /ON TIMER 2 Press INPUT PRESET/TUNING/BAND INPUT 2 or until “TUNER” (2, 7) appears on the display, or simply press TUNER on the remote control. A/B/C/D/E / UP DOWN 3 Press and hold MEMORY for more than 2 seconds. * The “MEMORY” (6) and “AUTO” (4) indicators flash. BASS TREBLE PHONES MODE DOLBY NR REC/ PAUSE AUTO/ MANUAL MEMORY RANDOM TIMER TIME ADJ HOUR 3 The tuner performs automatic tuning and searches for FM stations first and then AM stations. Received stations are programmed sequentially to A1, A2, A3 and so on. When the automatic preset tuning is completed; POWER 1 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 PRESET TIME A EDIT To recall a preset station 2 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE D • The automatic preset tuning search will be performed through all frequencies until 40 stations are stored. If the number of received stations is less than 40, the search will stop after searching all frequencies. * Since FM stations are searched for first, there may be a case that 40 preset stations are occupied by FM stations only. • With this function, only stations with sufficient signal strength are stored automatically. If the station you want to program is weak in signal strength, tune in to it with the Manual tuning method (in monaural) and program it by following the procedure in the section “To store stations” on page 22. • You can replace a preset station with another FM or AM station manually by simply following the procedure in the section “To store stations” on page 22. CD / DIRECTION TAPE — LEVEL Simply follow the procedure in the section “To recall a preset station” on page 22. Notes E REC/ PAUSE The display shows the frequencies of the first preset station (stored to A1). If you want to check the contents and the number of preset stations, follow the procedure in the section “To recall a preset station” on page 22. TEST CENTER/ REAR/ DELAY PROGRAM SLEEP MUSIC INPUT 2 Memory back-up The memory back-up circuit prevents the programmed data from being lost even if the AC supply lead is disconnected from the AC outlet or the power is cut due to temporary power failure. If, however, the power is cut for more than one week, the memory may be erased. If so, it can be re-programmed by simply following the Preset tuning steps. VOLUME E-21 English Automatic preset tuning  Tuning operation Manual preset tuning 6, 2 DISC 1 DISC 2 The built-in tuner can store station frequencies selected by tuning operation. With this function, you can select any desired station only by calling the corresponding preset station number. Up to 40 stations (8 stations x 5 groups) can be stored. DISC 3 3–DISC CD CHANGER 1 ■ To store stations STANDBY STANDBY /ON TIMER 1 Turn on the power. 2 PRESET/TUNING/BAND INPUT A/B/C/D/E 2 Press INPUT or until “TUNER” (2, 7) appears on the display, or simply press TUNER on the remote control. / BASS TREBLE PHONES MODE DOLBY NR REC/ PAUSE 1, 5 AUTO/ MANUAL MEMORY TIMER TIME ADJ RANDO HOUR 4, 7 3 Turn in to the desired station. 4 Press MEMORY. * “MEMORY” (6) and “PRESET” (1) will flash on the display for about 5 seconds. 5 Select the desired group (A – E) of preset stations by pressing A/ B/C/D/E before “MEMORY” (6) goes out. Confirm the selection on the display. POWER 1 6, 2 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME PRESET TIME A EDIT 6, 2 C MODE D or repeatedly or pressing a numeric button (1 to 8) before “MEMORY” (6) goes out. 7 Within about 5 seconds, press MEMORY again. 2 B DISC SKIP 6 Select a preset station number by pressing 6, 2 5, 1 ■ To recall a preset station 1 Select a group of preset stations by pressing A/B/C/D/E. 2 Select the desired preset station number by pressing or repeatedly or pressing a numeric button (1 to 8). E Notes • A new setting can be programmed in place of the former one. • As for the preset stations, the setting of AUTO/MANUAL is stored along with the station frequency. CD / DIRECTION TAPE REC/ PAUSE — LEVEL TEST CENTER/ REAR/ DELAY PROGRAM SLEEP MUSIC INPUT 2 VOLUME E-22  Playing back a tape Each indicator mentioned with a number on pages 24–30 corresponds to the indicator with the same number on this page. 1 100 350 1K 3.5K 10K MUSIC NR PROGRAM TAPE 2 1 Tape counter 2 NR (DOLBY NR) 3 Tape direction indicator 3 4 5 TAPE EDIT A B REC 6 7 4 Reverse mode indicator 5 TAPE (input source indicator) 8 VOLUME 9 7 (play) 8 EDIT 9 Tape side indicator 6 TAPE REC General information • Do not use C-120 tapes or poor quality tapes, since they can cause malfunctions. • Before loading a tape on the tray, tighten the tape slack with a pen or pencil. • Tapes have removable tabs which prevent accidental recording or erasing from taking place. Removing the tab on the top left corner protects the side facing you from erasure. Cover the tab holes with adhesive tape to erase or record again. • The tape deck features an automatic tape selector. Just load the tape, and the type of tape being used will be sensed automatically. • The tape deck can play back metal tapes as well as normal or high position tapes; however, recording cannot be done on metal tapes with good sound quality. Dolby B Type Noise Reduction Dolby noise reduction is an extremely effective method of reducing undesirable background hiss on tapes. The builtin tape deck incorporates Dolby B type noise reduction system. DOLBY NR is useful for both recording and playback; be sure that the same noise reduction is used on recording and playback. About the tape counter The tape deck is equipped with a tape counter that is useful for searching and locating a desired point on the tape. The tape counter is shown on the display. Pressing (stop) when the deck is being stopped will reset the tape counter to “0000”. 100 350 1K 3.5K 10K MUSIC PROGRAM PRO LOGIC HALL 3 STEREO YMERSION TUNER CD MD TAPE RANDOM EDIT S F REP A B PROG VOLUME Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Corporation. are “DOLBY” and the double-D symbol trademarks of Dolby Laboratories Licensing Corporation. E-23 English Display information  Playing back a tape 1 PROGRAM STANDBY STANDBY /ON 2 Basic operation DIGITAL AUDIO 3–DISC CD CHANGER B.BOOST MUSIC 1 Turn on the power. TIMER VOLUME PRESET/TUNING/BAND INPUT 2 Press INPUT A/B/C/D/E / UP or until “TAPE” (1, 5) appears on the DOWN display. 5 BASS TREBLE PHONES MODE DOLBY NR REC/ PAUSE (stop) 5 6 3, 4 AUTO/ MANUAL MEMORY RANDOM REPEAT TIMER TIME ADJ HOUR MIN TIME DISPLAY 3 Open the tray by pressing OPEN/CLOSE. 4 Load the tape on the tray with side A facing upward, and close DIRECTION the tray by pressing OPEN/CLOSE or pushing the front edge of the tray gently. OPEN/CLOSE AUTO REVERSE CASSETTE DECK DOLBY B NR 5 Press MODE or DIRECTION to change the current setting if necessary. Reverse mode indicator (4) 4 Tape direction indicator (3) Moves slowly in the current tape running direction during playback. MODE DIRECTION POWER Side A only 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE PRESET TIME A EDIT D (Repeats 8 times) Starts from side A. Side B only Side B only Side B → Side A → 1 Side A → Side B Side A → Side B → 1 (Repeats 8 times) Starts from side B. (Side A is not played the first time.) 6 Press . Playback begins. E To stop playback CD / Press . To remove the tape 5 DIRECTION Open the tray by pressing OPEN/CLOSE. (stop) TAPE REC/ PAUSE — LEVEL TEST 6 CENTER/ REAR/ DELAY PROGRAM MUSIC Direct operation SLEEP INPUT VOLUME E-24 2 and OPEN/CLOSE will work if they are pressed when this system is in the standby mode or another input source is selected.  Playing back a tape DISC 2 DISC 3 DISC CHANGE PROGRAM STANDBY B.BOOST Winding the tape 1 Press DIGITAL AUDIO 3–DISC CD CHANGER STANDBY /ON OPEN/CLOSE or English DISC 1 to wind the tape. MUSIC TIMER VOLUME PRESET/TUNING/BAND INPUT A/B/C/D/E Moves rapidly in the current tape running direction while winding. / UP DOWN BASS 2 Press TREBLE PHONES MODE DOLBY NR REC/ PAUSE AUTO/ MANUAL MEMORY RANDOM REPEAT TIMER TIME ADJ HOUR MIN TIME DISPLAY Note DIRECTION When the tape is wound to the end, the tape deck will then function as described below. : The tape stops at the end. : If the winding direction is , playback automatically starts from the reverse side when the tape reaches the end. , the tape stops at the end. If the winding direction is : When the tape reaches the end, playback automatically starts from the reverse side. OPEN/CLOSE AUTO REVERSE CASSETTE DECK to stop. DOLBY B NR (stop) Searching for the beginning of the desired selection POWER Press or during playback. The tape deck will find a blank interval between selections and start playback automatically. 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME To listen to the next selection B DISC SKIP C MODE Press Press PRESET TIME A EDIT D To listen to the same selection Press Press if the direction of the current playback is if the direction of the current playback is if the direction of the current playback is if the direction of the current playback is . . . . E Blinks on and off. CD / Moves rapidly in the current tape running direction while searching. (stop) DIRECTION Notes TAPE REC/ PAUSE — LEVEL TEST CENTER/ REAR/ DELAY PROGRAM SLEEP MUSIC • This function may not work for tapes with * Material with long pauses or quiet passages. * Low recording levels or excessive noise. * Pauses of less than 4 seconds between selections. • If searching is carried out near the beginning or the end of a selection, the searching may not be done successfully. INPUT VOLUME E-25  Recording Notes DISC 1 DISC 2 DISC 3 • Adjusting the VOLUME, BASS and TREBLE controls, and the use of B. BOOST, MUSIC and YMERSION have no effect on the recorded sound. The recording level is automatically adjusted. • A sound field program except for YMERSION may have effect on the recorded sound. If a sound field program is selected, cancel it before you begin recording. Refer to page 35 on how to cancel the sound field program. • If you want to make a recording using Dolby NR, press DOLBY NR so NR” (2) lights up on the display. If not, turn “ NR” (2) that “ off. * For details, refer to “Dolby B Type Noise Reduction” on page 23. 3–DISC CD CHANGER STANDBY 1 STANDBY /ON 2 TIMER PRESET/TUNING/BAND INPUT A/B/C/D/E / 4 BASS TREBLE PHONES MODE DOLBY NR REC/ PAUSE AUTO/ MANUAL MEMORY TIMER TIME ADJ RAN H 5 Basic recording DIRECTION 4 1 Turn on the power. 2 Press INPUT OPEN/CLOSE AUTO REVERSE CASSETTE DECK or repeatedly to select the source you want to record. DOLBY B NR 3 Load a tape on the tray with side A facing upward. 4 Press DIRECTION or MODE to change the current setting, if 3 necessary. POWER MODE 1 DIRECTION 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE PRESET TIME A EDIT D Side A only Side A → Side B Side B only Side B only 5 Press REC/PAUSE. * “TAPE REC” (6) lights up on the display. 6 Begin playing the source to be recorded and press E CD / 4 DIRECTION on the tape deck. When you record from another component that is connected to this system, start the recording on the tape deck first, and then start playing the connected source. * When playing a CD, the recording automatically begins a few seconds before the disc play begins. Displaying the tape counter TAPE 5 REC/ PAUSE — LEVEL During recording, the information of the playing source is displayed in place of the tape counter (1). Press DISPLAY to change the display to the tape counter. Pressing DISPLAY again will restore the previous display mode. TEST CENTER/ REAR/ DELAY PROGRAM SLEEP MUSIC INPUT 2 VOLUME E-26  Recording To stop recording temporarily DISC 1 DISC 2 DISC 3 PROGRAM STANDBY B.BOOST Press REC/PAUSE. * Press on the tape deck to resume recording. To stop recording DIGITAL AUDIO 3–DISC CD CHANGER STANDBY /ON OPEN/CLOSE DISC CHANGE English / MUSIC Press TIMER on the tape deck. VOLUME PRESET/TUNING/BAND INPUT A/B/C/D/E / To change the disc and track when recording from a CD UP DOWN BASS TREBLE PHONES MODE DOLBY NR REC/ PAUSE AUTO/ MANUAL MEMORY RANDOM REPEAT TIMER TIME ADJ HOUR MIN TIME DISPLAY 1 Press on the CD player. * The recording stops temporarily. DIRECTION 2 Select the disc by pressing DISC SKIP if necessary. 3 Choose the track you want to record next by using OPEN/CLOSE AUTO REVERSE CASSETTE DECK DOLBY B NR or . 4 Press REC/PAUSE Numeric buttons Notes • A sequence of tracks in the program play mode and random play mode of the CD player can be recorded in the same way. • During recording, you can rewind the tape to the point where the recording started by simply pressing or . POWER 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE PRESET TIME A EDIT / on the CD player to resume recording (or simply press the corresponding numeric button(s) on the remote control). D DISC SKIP E CD / / DIRECTION TAPE REC/ PAUSE REC/PAUSE — LEVEL TEST CENTER/ REAR/ DELAY PROGRAM SLEEP MUSIC INPUT VOLUME E-27  DISC 1 DISC 2 Recording from CDs utilizing the EDIT function DISC 3 The EDIT function performs recording on both sides of the tape. 3–DISC CD CHANGER STANDBY STANDBY /ON TIMER ■ EDIT recording PRESET/TUNING/BAND INPUT 1 A/B/C/D/E 1 Press INPUT or repeatedly until “CD” (1) appears on the display, and load the disc to be recorded. / BASS TREBLE PHONES MODE DOLBY NR REC/ PAUSE AUTO/ MANUAL MEMORY TIMER TIME ADJ RANDO HOUR 2 Select the disc by pressing DISC SKIP. 3 Load a tape on the tray with side A facing upward. 4 Select “ 4 ” (4) by pressing MODE. DIRECTION 5 Press R. TIME on the remote control to select the length of the OPEN/CLOSE AUTO REVERSE CASSETTE DECK tape to be used. When pressed, the display changes as shown below. (off) → C-46 → C-54 → C-60 → C-90 → DOLBY B NR 3 Numeric buttons When using tapes other than C-46, C-54, C-60 or C-90 After pressing R. TIME, input the tape length by using the numeric buttons on the remote control. POWER 6 Press EDIT. (“EDIT” (8) lights up on the display.) 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE PRESET TIME 6 A EDIT D 5 2 The following operations are carried out automatically. 1) Tracks on the disc are automatically divided into side A and side B. You can check the process by watching the display. * The tape side indicator (9) shows the side currently selected. 2) If the tape is not rewound to the end, it will rewind to the end rapidly. 3) The end part of the tape on which recording cannot be done is automatically wound. 4) Both disc play and recording starts. Recording is continuously carried out on both sides of the tape. E Note CD / When the CD player is in the all disc play mode, tracks on another disc are recorded continuously if the tape’s total possible recording time is longer than the total playing time of the selected disc. In this case, as many as three discs can be recorded automatically. DIRECTION TAPE REC/ PAUSE — LEVEL TEST CENTER/ REAR/ DELAY PROGRAM SLEEP MUSIC INPUT 1 VOLUME E-28  Recording ■ Auto-EDIT recording 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME PRESET TIME A EDIT 4 This recording automatically changes the order of tracks so that the unrecorded space of side A is minimized. B DISC SKIP D C MODE 1 Follow steps 1–5 on the previous page. 2 Press PROG. 3 Press R. TIME. “Auto A>>>” will light up during programming for side A, and “Auto B>>>” will light up during programming for side B. 2 3 4 Press EDIT. (“EDIT” (8) lights up on the display.) The recording begins. E CD / E-29 English POWER  Recording ■ Manual EDIT recording PROGRAM STANDBY STANDBY /ON B.BOOST MUSIC TIMER You can program tracks manually while watching the remaining time on both sides of the tape. VOLUME PRESET/TUNING/BAND INPUT A/B/C/D/E / UP DOWN 1 Press INPUT BASS or repeatedly until “CD” (1) appears on the display, and load a disc (or discs) on the disc tray. TREBLE PHONES MODE DOLBY NR REC/ PAUSE AUTO/ MANUAL MEMORY RANDOM REPEAT TIMER TIME ADJ HOUR MIN TIME DISPLAY 2 Follow steps 3–5 on page 28. 3 Press PROG. DIRECTION 1 * “PROG” and “P-01” will light up on the display, and all track numbers on the selected disc will begin blinking. TIME 4 If necessary, select the desired disc by pressing DISC SKIP. POWER 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE PRESET TIME 9 D 6 Repeat steps 4 and 5 to program more selections for side A of the tape. You can select the same track again. * Pressing TIME displays the total remaining time on side A of the tape for about 1 second, and then it is replaced by the display of the next play order. * You can only select track numbers 1 through 15 for manual EDIT recording. All track numbers higher than 15 i.e.16, 17, 18… cannot be selected for recording even if there is recordable space available on the tape. “TM OVER” will appear on the display. At this time, however, if any other track number is flashing continuously on the display, you can program it instead of the unprogrammable one. 7 TIME A EDIT 5 Select the desired track number by pressing the numeric buttons. 5 1 3 E 4 CD / DIRECTION 7 When the programming for side A is finished, press R. TIME. * “Side–B” appears on the display. You can begin programming for side B. * After following this step, you can check the programmed contents for side A and side B alternately by pressing R. TIME at any time before you press EDIT in step 9. * The tape side indicator (9) shows the programming side currently selected. TAPE REC/ PAUSE TEST — LEVEL CENTER/ REAR/ DELAY PROGRAM MUSIC SLEEP INPUT 1 8 Repeat steps 4 and 5 to program selections for side B of the tape. VOLUME You can select the same track again. Display information during programming Next play order 9 Press EDIT. (“EDIT” (8) lights up on the display.) The recording begins. Selected disc Note To check, cancel or correct program data, refer to page 16. TRACK NR CD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OVER 15 A PROG V Side of the tape To cancel the EDIT function Before recording, press on the CD player or the tape deck. To stop recording Total remaining time on this side of the tape Selected track number Notes on recording with the EDIT function TRACK REM NR CD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OVER 15 A PROG V Programmed track numbers light up and only programmable track numbers among unprogrammed ones flash. E-30 Press on the tape deck. (At this time, disc play automatically stops.) • The maximum number of tracks that can be programmed is 20. • The track number 16 or higher cannot be programmed by this function. • The CD player’s repeat play mode will be canceled during the recording mode.  Operating an external unit connected to this system DISC 2 DISC 3 DISC CHANGE DIGITAL AUDIO 3–DISC CD CHANGER PROGRAM STANDBY STANDBY /ON OPEN/CLOSE B.BOOST MUSIC TIMER VOLUME PRESET/TUNING/BAND INPUT A/B/C/D/E / UP TREBLE PHONES MODE DOLBY NR REC/ PAUSE ■ To listen to or watch a source played on an external unit connected to this system 1 Select the input source (VIDEO, VCR or AUX/MD) you want to play by using INPUT control). DOWN BASS Use an external unit connected to the VCR, VIDEO or AUX/ MD terminals on the rear of the main unit. AUTO/ MANUAL MEMORY RANDOM REPEAT TIMER TIME ADJ HOUR MIN TIME or (or INPUT on the remote DISPLAY 2 Play the source. * If you play a video source, turn on the TV monitor connected to this system. DIRECTION 3 Adjust the volume to the desired level by using VOLUME. OPEN/CLOSE AUTO REVERSE CASSETTE DECK * If you prefer, you can control the sound quality (Refer to pages 32–36). DOLBY B NR 3, 2 1 DIRECTION ■ To record a source by using the tape deck, VCR etc. connected to this system TAPE If a tape deck, VCR, etc. is connected to this system, you can record a source played on this system or an external audio/video unit connected to this system by using the tape deck, VCR, etc. REC/ PAUSE — LEVEL TEST CENTER/ REAR/ DELAY 1 Select the source you want to record by using INPUT or (or INPUT on the remote control) . PROGRAM MUSIC 2 Play the source and then turn VOLUME up to confirm the input SLEEP INPUT 3, 2 1, 1 source. 3 Begin recording on the tape deck, VCR, etc. VOLUME Note A digital-to-digital recording is possible from a CD played on the built-in CD player to an MD (or tape) on the MD recorder (or DAT) by connecting the DIGITAL OUT (OPTICAL) terminal on the rear of the main unit to the MD recorder (or DAT). E-31 English DISC 1  Various sound control 1 2 3 BASS BOOST 100 350 1K 3.5K 10K MUSIC ROCK POPS JAZZ CD PROGRAM PRO LOGIC HALL 3 STEREO YMERSION 4 VOLUME 5 1 Spectrum analyzer 3 VOLUME (volume level meter) 4 MUSIC (preset equalizer mode indicator) 5 PROGRAM (sound field program The spectrum of the input source which is divided into five bands will be indicated in real time. indicator) 2 BASS BOOST B.BOOST PROGRAM STANDBY STANDBY /ON ■ VOLUME control DIGITAL AUDIO 3–DISC CD CHANGER B.BOOST MUSIC TIMER VOLUME PRESET/TUNING/BAND INPUT A/B/C/D/E / UP DOWN BASS MODE DOLBY NR REC/ PAUSE AUTO/ MANUAL MEMORY RANDOM REPEAT TIMER TIME ADJ HOUR MIN TIME TREBLE VOLUME BASS TAPE REC/ PAUSE — LEVEL Press VOLUME to increase the volume and VOLUME to decrease the volume. * Adjusted volume level is shown by the volume level meter (3) and in figures on the display. ■ B. (BASS) BOOST button DIRECTION TEST Press this button so that “BASS BOOST” (2) is illuminated on the display to boost the bass frequency response of this system while maintaining overall tonal balance. This function is effective for reinforcing the bass frequencies when a subwoofer is not used. CENTER/ REAR/ DELAY PROGRAM SLEEP MUSIC ■ BASS and TREBLE controls BASS : Turn this knob clockwise to increase (or counterclockwise to decrease) the low frequency response. TREBLE : Turn this knob clockwise to increase (or counterclockwise to decrease) the high frequency response. INPUT VOLUME E-32 Rotate VOLUME in the “UP ” direction to increase the volume, and the “DOWN ” direction to decrease the volume. DISPLAY DIRECTION VOLUME Front panel operation Remote control operation TREBLE PHONES General sound control  Various sound control ■ Listening with headphones DISC 1 DISC 2 DISC 3 DISC CHANGE OPEN/CLOSE Note YMERSION PROGRAM STANDBY STANDBY /ON When you connect headphones, no signals are outputted to the speakers. DIGITAL AUDIO 3–DISC CD CHANGER B.BOOST MUSIC TIMER VOLUME PRESET/TUNING/BAND INPUT A/B/C/D/E / UP DOWN BASS TREBLE PHONES MODE DOLBY NR REC/ PAUSE AUTO/ MANUAL MEMORY RANDOM REPEAT TIMER TIME ADJ HOUR MIN TIME DISPLAY Graphic equalizer OPEN/CLOSE DISC CHANGE The built-in graphic equalizer provides 3 preset equalizer modes as listed below. Preset graphic equalizer modes DIGITAL AUDIO Mode PROGRAM B.BOOST MUSIC ROCK High and low frequencies are emphasized. This mode is suitable for reproducing dynamic and powerful sounds of rock music, etc. POPS Vocals are emphasized and whole sound is clear. This mode is suitable for pops. JAZZ High frequencies for piano, sax, etc. are emphasized. Medium frequencies for vocals are also moderately emphasized. MUSIC VOLUME TAPE REC/ PAUSE — LEVEL TEST Listening to the music with a preset equalizer effect CENTER/ REAR/ DELAY PROGRAM MUSIC MUSIC SLEEP INPUT Feature 1 Play back a source. 2 Press MUSIC repeatedly until the name of the desired mode lights up on the preset equalizer mode indicator (MUSIC) (4). VOLUME ROCK POPS JAZZ (OFF) E-33 English PHONES • Be sure that your headphones have a 3.5 mm (1/8”) diameter plug and between 16 ohms and 50 ohms impedance. Recommended impedance is 32 ohms. • When you listen with headphones, connect the headphones to the PHONES jack. You can listen to the sound that is normally outputted from the front speakers through headphones. Adjust VOLUME to a comfortable listening level.  Various sound control Sound field processor The Sound Field Processor built into this system enables you to enjoy listening to a source with an ambience of actual concert hall or three-dimensional acoustics. This system provides preset sound field programs shown below. You can enjoy an excellent sound field by selecting any one of them and by adding any other desired adjustments. This system also incorporates a Dolby Pro Logic Surround decoder for multi-channel sound reproduction of Dolby Surround encoded video sources. The operation of the Dolby Pro Logic Surround decoder can be controlled by selecting a corresponding sound field program. ■ Sound field programs Program Feature PRO LOGIC This program is used for playing sources encoded with Dolby Surround. Dolby Pro Logic Surround uses four discrete channels and five speakers to reproduce realistic and dynamic sound effects: two main channels (left and right), a center channel for dialogue, and a rear channel for special sound effects. The rear channel reproduces sound within a narrow frequency range. 3 STEREO This program is used for simplified play of Dolby Surround encoded sources. With this program, sound effects are outputted from the front left and right speakers and no sound from the rear speakers. YMERSION HALL YMERSION is Yamaha’s proprietary technology that enhances the spread of a normal stereo source play sound, creating three-dimensional acoustics using only two speakers. This program presents you with an ambience of actual concert hall by adding effects as sonic reflections or reberverations that create sound environment of a hall. Sound effects are outputted from the front and rear speakers. Orchestra and opera music is suited for this sound field. DOLBY SURROUND P R O • L O G I C Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. ©1992–1997 Dolby Laboratories, Inc. All rights reserved. E-34  Various sound control ■ Listening to the music with a sound field effect English OPEN/CLOSE DISC CHANGE 1 Play a source. 2 Press PROGRAM repeatedly until the name of the desired DIGITAL AUDIO PROGRAM B.BOOST MUSIC program lights up on the sound field program indicator (5). * Whenever you press PROGRAM, the program changes and is displayed as follows. PROGRAM PROGRAM PRO LOGIC PROGRAM PROGRAM 3 STEREO PROGRAM HALL YMERSION VOLUME (OFF) 3 If desired, adjust the delay time and the output level of each CENTER/REAR/DELAY TAPE REC/ PAUSE LEVEL- / + — LEVEL TEST CENTER/ REAR/ DELAY PROGRAM MUSIC speaker. (For details, refer to the corresponding descriptions on pages 35–36.) Notes • When YMERSION is selected, no sound is heard from the center speaker nor rear speakers. • If you play a source not encoded with Dolby Surround when PRO LOGIC is selected, the source may not be played normally. PROGRAM SLEEP INPUT ■ Adjusting delay time and speaker output level VOLUME DELAY TIME You can adjust the time difference between the beginning of the sound from the front speakers and the beginning of the effect sound from the rear speakers. The larger the value, the later the effect sound is generated. PRO This adjustment can be made individually for both LOGIC and HALL. Control range PRO LOGIC: 15, 20, 25, 30 milliseconds HALL: 15, 20, 25, 30, 40, 50 milliseconds 1 Press CENTER/REAR/DELAY repeatedly until “DELAY” appears on the display. 2 By pressing LEVEL + or – continuously, the value also changes continuously. Changes. E-35  Various sound control If desired, you can adjust the sound output level of the center and/ or rear speakers even if the output level is already set in “Speaker balance adjustment” on page 11. POWER 1 2 3 CENTER LEVEL 1 4 2 5 3 6 Control range : +10 to –21 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE PRESET TIME A EDIT D 1 Press CENTER/REAR/DELAY repeatedly until “CENTER” appears on the display. 2 By pressing LEVEL + or – continuously, the level value also changes continuously. E Changes. CD / Notes • This adjustment can be made only when the sound field program PRO LOGIC or 3 STEREO is selected. • Once the output level is adjusted, the level value will be the same for both the PRO LOGIC and 3 STEREO programs. DIRECTION REAR LEVEL TAPE REC/ PAUSE — LEVEL TEST CENTER/ REAR/ DELAY LEVEL- /+ PROGRAM SLEEP MUSIC INPUT CENTER/ REAR/ DELAY Control range : +10 to –21 1 Press CENTER/REAR/DELAY repeatedly until “REAR” appears on the display. 2 By pressing LEVEL + or – continuously, the level value also changes continuously. VOLUME Changes. Notes • This adjustment can be made only when a sound field program PRO LOGIC or HALL is selected. • Adjustment can be made individually for both PRO LOGIC and HALL. E-36  Using the built-in timer Timer play INPUT DISC 1 DISC 2 DISC 3 DISC CHANGE DIGITAL AUDIO 3–DISC CD CHANGER PROGRAM STANDBY STANDBY /ON OPEN/CLOSE B.BOOST MUSIC TIMER VOLUME PRESET/TUNING/BAND INPUT A/B/C/D/E / UP DOWN BASS TREBLE PHONES MODE DOLBY NR REC/ PAUSE AUTO/ MANUAL MEMORY RANDOM REPEAT TIMER TIME ADJ HOUR MIN TIMER TIME DISPLAY MIN HOUR DISPLAY By using the built-in timer, you can set the time when this system turns on and a source play begins, and the time when this system is set to the standby mode. 1 Press DISPLAY. Whenever DISPLAY is pressed, the display mode changes as follows. → 1 Current time (TIMER on/off mode) ↓ 2 Source selecting mode (TAPE, TUNER, CD) ↓ 3 ON TIME/Time setting mode ↓ 4 OFF TIME/Time setting mode ↓ 5 Normal display mode POWER POWER (standby/on) 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 TUNER +I0 PROG PRESET R.TIME B DISC SKIP C MODE PRESET TIME A EDIT D 2 Source selecting mode Select the source to be played with INPUT INPUT on the remote control). TAPE TEST 2 Press TIMER to complete the timer play setting. CENTER/ REAR/ DELAY SLEEP This system turns into the standby mode. * The STANDBY and TIMER indicators light up. MUSIC INPUT INPUT VOLUME (or 4 OFF TIME/time setting mode If necessary, set the time when you want to finish the timer play in the same way as you did in step 3. If you do not set the time, it will be automatically set so that the timer play finishes after 1 hour. DIRECTION PROGRAM or 3 ON TIME/time setting mode [“ON TIME” appears on the display, and soon it is changed to a time setting mode.] Set the time when you want to begin the timer play. • Press HOUR and set the hour. • Press MIN and set the minute. CD / — LEVEL The display mode will change in about 8 seconds. If the mode is changed before the setting is completed, call the mode again by pressing DISPLAY once or more. 1 Current time Make sure that the current time is correct, and press TIMER so that “TIMER” lights up on the display. E REC/ PAUSE Note If you will continue using this system, press STANDBY/ON to turn on this system. To cancel the timer play setting Press DISPLAY, and then press TIMER so that the TIMER indicator goes out. Note Unless there is a power failure for more than 5 minutes, the set time will be retained until it is reset. E-37 English STANDBY/ON  Using the built-in timer DISC 1 DISC 2 DISC 3 DISC CHANGE PROGRAM STANDBY B.BOOST MUSIC TIMER VOLUME PRESET/TUNING/BAND INPUT A/B/C/D/E / UP DOWN BASS TREBLE PHONES REC/PAUSE MODE DOLBY NR REC/ PAUSE AUTO/ MANUAL MEMORY RANDOM REPEAT TIMER TIME ADJ HOUR MIN TIMER TIME Timer recording 1 Follow steps 2–3 of “Basic recording” on page 26. DIGITAL AUDIO 3–DISC CD CHANGER STANDBY /ON OPEN/CLOSE DISPLAY DISPLAY 2 Tune in to the station you want to record. 3 Follow step 1 of “Timer play” on page 37. * In step 2, select “TUNER”, and then press REC/PAUSE. (“REC >TAPE” and the frequency will flash alternately on the display.) * In step 3, set the time when you want to begin recording. * In step 4, set the time when you want to finish recording. 4 Press TIMER. This system will be set to the standby mode. * The STANDBY and TIMER indicators light up. To cancel the setting of timer recording TAPE REC/ PAUSE TEST Press DISPLAY once or more so that “REC >TAPE” flashes on the display. While “REC >TAPE” is flashing, press REC/ PAUSE. REC/PAUSE — LEVEL CENTER/ REAR/ DELAY PROGRAM SLEEP MUSIC INPUT SLEEP VOLUME Note When the timer recording is finished, the timer setting is automatically canceled. Sleep timer operation This system will automatically be set to the standby mode when the selected sleep time passes. 1 Play the desired sound source. 2 Press SLEEP repeatedly until the desired sleep time appears on the display. The display will change as described below. 2h00m 1h30m 1h00m 0h30m OFF SLEEP (Sleep timer is off.) * The normal display mode will resume about 4 seconds after the selection is made. * “SLEEP” will light up on the display. E-38  Appendix Refer to the chart below when this system does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, disconnect the supply lead and contact your authorized YAMAHA dealer or service center. Problem Cause What to Do This system does not work normally. There is an influence of strong external noise (lightning, excessive static electricity, etc.) or the system was operated incorrectly. Set this system to the standby mode and disconnect the AC supply lead from the AC outlet. After about 30 seconds, connect the power and operate this system again. General The sound suddenly goes off. The protection circuit was activated because of a short circuit, etc. Set this system to the standby mode, then turn on to reset the protection circuit. The SLEEP timer was activated. Cancel the SLEEP timer function. No sound from speakers. Speaker connections are not secure. Secure the connections. No sound from the rear speakers. The sound output level to the rear speakers is set to minimum. Raise the sound output level to the rear speakers. Incorrect sound field program selection. No sound field program is selected. Select the appropriate program. The sound output level to the center speaker is set to minimum. Raise the sound output level to the center speaker. Incorrect sound field program selection. No sound field program is selected. Select the appropriate program. No sound (or no picture) from the external unit connected to this system. Incorrect cord connections. Connect the cords properly. If the problem persists, the cords may be defective. Input source selection is not correct. Make a correct input source selection. Timer cannot be set. Current time is not set. Set current time. This system will not operate properly. The internal microcomputer has been frozen by an external electric shock (lightning, excessive static electricity, etc.) or power supply with low voltage. Unplug the AC supply lead from the wall AC outlet, then plug in again after about one minute. The volume level cannot be increased, or sound is distorted. The component connected to the AUX/MD or VCR terminals on the rear of the main unit is turned off. Turn on the power to the component. A picture of the TV is disturbed. There is an influence of magnet from the center speaker. Place the center speaker apart from the TV. Excessive static in FM broadcasts. Interference from starting motor of nearby car. Position the FM antenna as high and as far away from nearby roads as possible. Use coaxial cable. No sound from the center speaker. Interference from thermostat of nearby electric appliance. Tuner Noise increases during stereo broadcasts. Antenna input is too weak due to obstructions or excessive distance from broadcasting station. Check antenna connections. Install a multi-element type FM antenna if possible. Stereo broadcasts are noisy Insufficient antenna input. and STEREO indicator blinks on and off. Install an antenna suited for the electric field strength of your area. Preset stations cannot be selected. Preset memory has been erased. Reprogram memory presettings. Buzzing or static during AM broadcasts. Interference from sources such as lightning, fluorescent lights, electric motors or thermostat of nearby electric appliance. Problem is difficult to eliminate but can be lessened by grounding AM loop antenna. TV or this system is being used nearby. Move away from TV or this system. Radio signal is weak or antenna is not properly connected. Properly connect AM loop antenna. AM broadcast sensitivity is poor. Change orientation of AM loop antenna. Install an external AM antenna. E-39 English Troubleshooting  Appendix Cause CD player Problem The disc is not a standard type. Play another disc. Play will not begin even if disc is loaded. Disc is upside down. Load disc with label side facing upward. Disc is dirty. Clean disc. No sound. The input source selection is incorrect. Select the CD player by pressing INPUT button until “CD” lights up on the display. Sound stops suddenly (always at the same spot). Disc is dirty. Clean disc. Volume is set too high. Lower volume. Tape will not move during playback or recording. Slack tape wrapped around pinch roller. Tighten slack with a pencil (pen) before using. Recording is not possible. Erasure prevention tab is broken off. Replace tape or cover erasure prevention hole with adhesive tape. Head is dirty. Clean heads. Sound is distorted or fades Head is dirty. out, or stereo balance is poor. Tape is worn. Clean heads. Poor sound quality. Tape deck What to Do A disc cannot be played normally, or there is a noise during play. Excessive noise. Replace tape. Tape encoded with Dolby NR is played back Press the DOLBY NR button to turn it on. with this system’s Dolby NR off. Tape not encoded with Dolby NR is played back with this system’s Dolby NR on. Press the DOLBY NR button to turn it off. Head has become magnetized. Demagnetize heads with head demagnetizer. Tape travel stops in middle of Slack tape coming out of cassette shell. playback or recording. Tape is creased or torn. The beginning of desired selections on tape cannot be found. or Tighten slack with a pencil (pen) before using. Replace tape. Endless tape is being used. Do not use endless tapes. Silent gaps between selections are too short. The function of searching for the beginning of desired selections will not operate unless the silent gaps between selections are at least four seconds long. Excessively soft passages in middle of selections. Remote control Conversation, etc. is recorded. Beginning of the track isn’t recorded. There is an unrecordable part in the first few Wind the unrecordable part of the tape and start seconds of the tape. recording from the recordable part. Remote control does not work. Batteries are dead. Replace batteries. Remote control is too far away or tilted too much. Use within 6 m and 60° radius. Direct sunlight or lighting (of an inverter type fluorescent lamp, etc.) is striking the remote control sensor of the main unit. Reposition the main unit. Remote control is being used near TV set with a remote control sensor. Relocate the main unit away from the TV. TV functions strangely when the remote control is used. E-40  Appendix ■ Amplifier section ■ Speaker section Minimum RMS Output Power per Channel FRONT 6 ohm, 1 kHz, 0.9% THD ........................... 80W+80W 6 ohm, 1 kHz, 10% THD ........................ 100W+100W CENTER 6 ohm, 1 kHz, 0.9% THD ...................................... 80W 6 ohm, 1 kHz, 10% THD ..................................... 100W REAR 6 ohm, 1 kHz, 0.9% THD ...................................... 25W 6 ohm, 1 kHz, 10% THD ....................................... 30W Type (Magnetic shielding type) Front speaker ....... 3-way bass reflex: 13 cm (5”) woofer 5 cm (2”) tweeter 2 cm (3/4”) super tweeter Center speaker ............................ 8 (3”) cm full range x 2 Rear speaker ..................................... 8 (3”) cm full range Maximum input Front, Center, Rear ......................... 220W, 180W, 100W Input Sensitivity/Impedance AUX/MD ........................................... 200 mV/47 k-ohm Impedance Front, Center ......................................................... 6 ohm Rear ..................................................................... 12 ohm Spectrum Analyzer Band ....................................... 5 bands (100 Hz, 350 Hz, 1 kHz, 3.5 kHz, 10 kHz) ■ General ■ Video section Power Supply [U.S.A. and Canada models] ................ AC 120V, 60 Hz [Australia model] ................................. AC 240V, 50 Hz Video Signal Level .................................... 1 Vp-p/75 ohm ■ Tuner section Tuning Range FM [U.S.A. and Canada models] .......... 87.5 to 107.9 MHz [Australia model] ............................ 87.5 to 108.0 MHz AM [U.S.A. and Canada models] ............. 530 to 1,710 kHz [Australia model] ............................... 531 to 1,611 kHz Usable Sensitivity (FM) DIN, Mono, S/N 26 dB ..................................... 1.8 µV S/N 30 dB, 1 kHz, 100% Mod. .......................... 1.5 µV ■ CD player section Discs Supported ................................................. Audio CD Type ...................................... 3 disc carousel auto-changer D/A Converter .................................................. 1-bit DAC Filter ............................. 8-time oversampling digital filter ■ Tape deck section Power consumption .................................................. 170W Dimensions (W x H x D) Main unit ........................................ 280 x 320 x 364 mm (11” x 12-5/8” x 14-5/16”) Front Speaker ................................. 200 x 320 x 208 mm (7-7/8” x 12-5/8” x 8-3/16”) Center Speaker ............................... 280 x 100 x 188 mm (11” x 3-15/16” x 7-3/8”) Rear Speaker .................................... 94 x 117 x 108 mm (3-11/16” x 4-5/8” x 4-1/4”) Weight Main unit ...................................... 10.5 kg (23 lbs. 2 oz.) Front Speaker ............................ 3.8 kg ( 8 lbs. 6 oz.) x 2 Center Speaker ................................. 2.0 kg (4 lbs. 6 oz.) Rear Speaker ............................. 0.7 kg ( 1 lbs. 9 oz.) x 2 Accessories ................................................ Remote control Batteries Speaker cords AM loop antenna Indoor FM antenna Mounting brackets Screws Velcro strips Specifications are subject to change without notice. Type .............................. Auto reverse stereo cassette deck Frequency Response (–20 dB) Type 1 (Normal) .................................... 50 to 15,000 Hz Type 2 (High) ......................................... 50 to 16,000 Hz Wow and Flutter ....................................... 0.09%, W.RMS Signal-to-Noise Ratio .................. 58 dB (Dolby NR OFF) 66 dB (Dolby B NR ON) Harmonic Distortion .................................................. 0.8% E-41 English Specifications  YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA Printed in Malaysia V558820