Black Box LMC1012A El manual del propietario

Marca: Black Box

Modelo: LMC1012A

Categoría: Convertidores de medios de red

Tipo: El manual del propietario

Este manual también es adecuado para

TRADEMARKS USED IN THIS MANUAL

Black Box and the Double Diamon logo are registered trademarks of

BB Technologies, Inc. Any other trademarks mentioned in this manual

are acknowledged to be the property of the trademark owners.

FEDERAL COMMUNICATIONS COMMISSION AND

CANADIAN DEPARTMENT OF COMMUNICATIONS

RADIO FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio frequency en-

ergy and if not installed and used properly, that is, in strict accordance

with the manufacturer’s instructions, may cause interference to radio

communication. It has been tested and found to comply with the limits

for a Class A computing device in accordance with the specifications

in subpart J of Part 15 of FCC rules, which are designed to provide

reasonable protection against such interference when the equipment is

operated in a commercial environment. Operation of this equipment in

a residential area is likely to be cause interference, in which case the

user at his own expense will be required to take whatever measures

may be necessary to correct the interference.

Changes or modifications not expressly approved by the party respon-

sible for compliance could void the user’s authority to operate the

equipment.

This digital apparatus does not exceed the Class A limits for radio noise

emission from digital apparatus set out in the Radio Interference Regu-

lation of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques

dépassant les limites applicables aux appareils numéirques de las classe

A prescrites dans le Règlement sur le brouillage radioélectrique publié

par le ministère des Communications du Canada.

NORMAS OFICIALES MEXICANAS (NOM)

ELECTRICAL SAFETY STATEMENT

1. Todas las instrucciones de seguridad y operación deberán ser leídas

antes de que el aparato eléctrico sea operado.

2. Las instrucciones de seguridad y operación deberán ser guardadas

para referencia futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones

de operación deben ser respetadas.

4. Todas las instrucciones de operación y uso deben ser seguidas.

5. El aparato eléctrico no deberá ser usado cerca del agua—por

ejemplo, cerca de la tina de baño, lavabo, sótano mojado o cerca

de una alberca, etc.

6. El aparato eléctrico debe ser usado únicamente con carritos o

pedelstales que sean recomendados por el fabricante.

7. El aparato eléctrico debe ser montado a la pared o al techo sólo

como sea recomendado por el fabricante.

8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico

más allá a lo descrito en las instrucciones de operación. Todo otro

servicio deberá ser referido a personal de servicio calificado.

9. El aparato eléctrico debe ser situado de tal manera que su posición

no interfiera su uso. La colocación del aparato eléctrico sobre una

cama, sofá, alfombra or superficie similar puede bloquea la

ventilación, no se debe colocar en libreros o gabinetes que impidan

el flujo de aire por los orificios de ventilación.

10. El equipo eléctrico deber ser situado fuera del alcance de fuentes

de calor como radiadores, registros de calor, estufas u ostros aparatos

(incluyendo amplificadores) que producen calor.

11. El aparato eléctrico deberá ser connectado a una fuente de poder

sólo del tipo descrito en el instructivo de operación, o como se

indique en el aparato.

12. Precación debe ser tomada de tal manera que la tierra fisica y la

polarización del equipo no sea eliminada.

13. Los cables de la fuente de poder deben ser guiados de tal manera

que no sean pisados ni pellizcados por objetos colocados sobre o

contra ellos, poniendo particular atención a los contactos y

receptáculos donde salen del aparato.

14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las

recomendaciones del fabricante.

15. En caso de existir, una antena externa deberá ser localizada lejos

de las lineas de energia.

16. El cable de corriente deberá ser desconectado del cuando el equipo

no sea usado por un largo periodo de tiempo.

17. Cuidado debe ser tomado de tal manera que objectos liquidos no

sean derramados sobre la cubierta u orificios de ventilación.

18. Servicio por personal calificado deberá ser provisto cuando:

A: El cable de poder o el contacto ha sido dañado; u

B: Objectos han caído o líquido ha sido derramado dentro del

aparato; o

C: El aparato ha sido expuesto a la lluvia; o

D: El aparato parece no operar normalmente o muestra un cambio

en su desempeño; o

E: El aparto ha sido tirado o su cubierta ha sido dañada.

040-01019-R31B 3/11

Specifications:

Description 1000Base-T UTP to 1000Base-X Fiber

Converter with Auto-Negotiation

Protocols 802.3ab, 1000Base-T, 1000Base-X

UTP Cable Type EIA/TIA 568A/B

Category 5 and higher

Fiber Cable Type Multimode:50/125,62.5/125 um

Single-mode: 9/125 um

UTP Connector Type RJ45

Fiber Connector Type Dual fiber: SC, LC

Controls DIP-Switches, LED Display

Power Requirements

AC Adapter Input [US] 120VAC 240mA 60Hz

AC Adapter Input

[Universal] 100-250VAC 500mA 50-60Hz

DC Adapter Input

(Model LMC204A)

[Optional] 18-60VDC

Dimension (WxDxH) W:4.6" x D:3.3" x H:0.85"

Weight 6 oz.

Compliance UL, CE, FCC Class A

Temperature

Operational 0 to +50

Storage -50 to +80

Humidity

(non-condensing) 0% to 95%

Altitude [ft] Up to 10,000

MTBF [hrs] 850,000

MTTR 5 min.

LED Indicators:

LED Color Status Description

Power Amber On Power applied

FDX/HDX Amber On UTP Full-Duplex

Off UTP Half Duplex

F/O

Link/Rx Green On Fiber Link

Flash Data received

Blink

(1Hz) In F/O "Auto-Neg."

mode:

Fiber cable connected,

but Fiber Link disabled

due to UTP or return

Fiber Link not ready

Off No Fiber Link

UTP

Link/Rx Green On UTP Link

Flash Data received

Blink

(1Hz) In F/O "Manual" mode

w/ "Link Prop.":

UTP cable connected,

but UTP Link disabled

due to loss of Fiber Rx

Off No UTP Link

Description:

The FlexPoint Gx converts between 1000Base-X (Sx/Lx)

Gigabit Ethernet fiber and 1000Base-T twisted pair (RJ45

UTP) cabling. The fiber optic (F/O) port supports

Auto-Negotiation (AN) which automatically detects and

advertises the Duplex and Pause ability of the connected

remote device. The multimode (MM) and single-mode

(SM) models are described here:

Model Fiber Distance

LMC1003A-R3 850nm,MM,SC 220m* / 720 ft.

LMC1004A-R3 1310nm,SM,SC 10km / 6.2 mi.

LMC1009A-R3 1310nm,SM,LC 10km / 6.2 mi.

LMC1012A 850nm, MM, LC 220m* / 720 ft.

Power Adapter Notice:

1. When using in a stand-alone configuration, this product

is intended to be and must be used only with a Listed

Direct Plug-In Power Unit marked “Class VI” and

rated at 9Vdc, 1 Amp.

2. This product should only be used with Black Box Supplied

Power Unit.

Mounting and Cable Attachment:

The FlexPoint Gx can be mounted standalone using a

wall-mounting kit or a DIN-rail bracket. It can also be

rack-mounted using a 5-unit shelf or a high-density

14-unit FlexPoint Powered Chassis. An 18-60VDC power

adapter is available for standalone or DIN-rail mounted

applications.

Attach the FlexPoint Gx UTP via a category 5 or higher

cable to a 1000Base-T Ethernet device. Attach the

FlexPoint Gx fiber via a single-mode or multimode (as

needed) cable to a 1000Base-X Gigabit Ethernet device

(make sure to use the correct wavelength source for the

model being used). The FlexPoint transmit (Tx) must

attach to the receive side on the other device; the receive

(Rx) must attach to the transmit.

DIP-Switch Settings:

F/O Auto-Negotiation “Auto-Neg/Manual” DIP-Switch:

When the FlexPoint Gx is connected to a UTP device

and a F/O device, the F/O Auto-Negotiation transparently

allows the two devices to negotiate Duplex and Pause

modes with each other.

Setting this DIP-switch to “Auto-Neg” (factory default)

enables the FlexPoint Gx’s F/O port to detect the Duplex

and Pause modes of the connected F/O device. The

WARNING!

Before inserting the Power Adapter, verify

that the power on the unit is appropriate

for your AC line voltage source.

FlexPoint Gx’s UTP port then negotiates with the

connected UTP device based on the modes detected by

the F/O port. Both the FlexPoint Gx and the

connected F/O device must have their Auto-Negotiation

enabled for this process to work.

Setting this DIP-switch to “Manual” will disable the F/O

port’s ability to detect the Duplex and Pause modes of

the connected F/O device. The FlexPoint Gx’s UTP port

negotiates with the connected UTP device based on the

modes configured by the UTP “Full-Duplex/Half-Duplex”

and “Pause Enable/Pause Disable” DIP-switches.

Note that in F/O Auto-Negotiation (AN) mode,

connecting the F/O cables before connecting the

UTP cables causes the F/O LED to blink steadily. The

blinking LED turns solid when the UTP Link is on.

Note that when F/O Auto-Negotiation is in the

“Enable” position, all the other DIP-switches have

no effect when the links are established.

UTP “Full-Duplex/Half-Duplex” DIP-Switch:

This DIP-switch has no affect if the FlexPoint Gx is in

F/O AN mode. This DIP-switch configures the Duplex

capability when the UTP port is Auto-Negotiating with

the connected UTP device. Setting the DIP-switch to

“Full-Duplex” (factory default) allows the UTP port to

Auto-Negotiate to Full-Duplex or Half-Duplex. Setting

the DIP-switch to “Half-Duplex” forces the UTP port to

Auto-Negotiate only to Half-Duplex.

UTP “Pause Enable/Pause Disable” DIP-Switch:

This DIP-switch has no affect if the FlexPoint Gx is in

F/O AN mode. This DIP-switch configures the Pause

capability when the UTP is Auto-Negotiating with the

Order toll-free in the U.S.: Call 877-877-BBOX

(outside U.S. call 724-746-5500)

FREE technical support 24 hours a day, 7 days

a week; Call 724-746-5500

Mailing address: Black Box Corporation,

1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com

E-mail: [email protected]

CUSTOMER

SUPPORT

INFORMATION

FlexPoint™ Gx

LMC1003A-R3

LMC1004A-R3

LMC1009A-R3

LMC1012A

connected UTP device. Setting the DIP-switch to

“Pause Enable” (factory default) allows the UTP port to

Auto-Negotiate to Symmetrical and Asymmetrical Pause.

Setting the DIP-switch to “Pause Disable” forces the

UTP port to Auto-Negotiate only to No Pause.

“Link Prop./Link Isolate” DIP-Switch:

This DIP-switch has no affect if the FlexPoint Gx is in

F/O AN mode. Setting this DIP-switch to “Link Prop.”

allows the link state to propagate from the UTP port to

the F/O port, and allows the link state to propagate from

the F/O port to the UTP port. The loss of a receive link

on the F/O port causes the transmit link of the UTP port

to be turned off, and the loss of a receive link on the

UTP port causes the transmit link on the F/O port to be

turned off.

This allows the loss of a link to be propagated and

detected by SNMP or other managed network devices

to which the FlexPoint Gx is connected.

Only the first loss of a receive link detected by the

FlexPoint Gx turns off the transmit link of the other port.

An additional loss of receive link on the other port has no

effect to the FlexPoint Gx. The FlexPoint Gx returns to

normal operation when the first loss of receive link is

restored.

When set to “Link Isolate” (factory default), the generation

and detection of link presence is done at each

point-to-point segment. Loss of a receive link on any

port has no effect on transmit signals of the other port.

1000 Park Drive z Lawrence, PA 15055-1018

724-746-5500

LMC1003A-R3, version 2

* Distances for multimode are dependent on fiber

cable used:

OM1 62.5 micron, 220 m; OM2 50 micron, 550m

Description:

The FlexPoint Gx converts between 1000Base-X (Sx/Lx)

Gigabit Ethernet fiber and 1000Base-T twisted pair (RJ45

UTP) cabling. The fiber optic (F/O) port supports

Auto-Negotiation (AN) which automatically detects and

advertises the Duplex and Pause ability of the connected

remote device. The multimode (MM) and single-mode

(SM) models are described here:

Distance

Model Fiber