Yamaha RX-V383 El manual del propietario

Categoría
Receptores AV
Tipo
El manual del propietario
AV Receiver
Owner's Manual
This unit is a product for enjoying video and music at home.
This manual explains preparations and operations for everyday users of the unit.
Read the supplied booklet “Quick Start Guide” before using the unit.
EN
CONTENTS
BEFORE USING THE UNIT 4
Accessories................................................................................................ 4
How to use this manual............................................................................ 4
Remote control.......................................................................................... 4
Insert the batteries................................................................................................................................................................... 4
Operating range of the remote control........................................................................................................................... 4
FEATURES 5
What you can do with the unit................................................................. 5
Part names and functions......................................................................... 7
Front panel................................................................................................................................................................................. 7
Front display (indicators)....................................................................................................................................................... 8
Rear panel................................................................................................................................................................................... 9
Remote control....................................................................................................................................................................... 10
PREPARATIONS 11
1 Placing speakers............................................................................... 12
Typical speaker layouts....................................................................................................................................................... 13
Other speaker layouts.......................................................................................................................................................... 14
Setting the speaker impedance....................................................................................................................................... 15
2 Connecting speakers........................................................................ 16
Connecting speaker cables................................................................................................................................................ 17
Connecting the subwoofer (with built-in amplifier)................................................................................................. 17
3 Connecting a TV/playback devices.................................................. 18
Input/output jacks and cables.......................................................................................................................................... 18
Connecting a TV..................................................................................................................................................................... 19
Connecting video devices (such as BD/DVD players).............................................................................................. 20
Connecting audio devices (such as CD players)......................................................................................................... 22
Connecting to the jack on the front panel................................................................................................................... 22
4 Connecting the FM/AM antennas.................................................... 23
5 Connecting the power cable............................................................ 23
6 Selecting an on-screen menu language.......................................... 24
7 Optimizing the speaker settings automatically (YPAO)................ 25
Error messages....................................................................................................................................................................... 27
Warning messages................................................................................................................................................................ 28
PLAYBACK 29
Basic playback procedure...................................................................... 29
Enjoying playback................................................................................................................................................................. 29
Switching information on the front display................................................................................................................. 30
Selecting the input source and favorite settings with one touch
(SCENE).................................................................................................... 31
Selecting a registered scene.............................................................................................................................................. 31
Registering a scene............................................................................................................................................................... 31
Selecting the sound mode..................................................................... 32
Enjoying sound field effects (CINEMA DSP)................................................................................................................. 33
Enjoying unprocessed playback...................................................................................................................................... 35
Enhancing the bass (Extra Bass)....................................................................................................................................... 36
Playing back digitally compressed formats (such as MP3, etc.) with enriched sound (Compressed
Music Enhancer)
..................................................................................................................................................................... 36
Listening to FM/AM radio....................................................................... 37
Setting the frequency steps............................................................................................................................................... 37
Selecting a frequency for reception............................................................................................................................... 37
Registering favorite radio stations (presets)................................................................................................................ 38
Radio Data System tuning.................................................................................................................................................. 41
Playing back music stored on a Bluetooth® device.............................. 42
Connecting a Bluetooth® device (pairing).................................................................................................................... 42
Playback of Bluetooth® device contents....................................................................................................................... 43
Enjoying audio using Bluetooth® speakers/headphones....................................................................................... 43
Playing back music stored on a USB storage device............................ 44
Connecting a USB storage device................................................................................................................................... 44
Playback of USB storage device contents..................................................................................................................... 44
En
2
Configuring playback settings for different playback sources
(Option menu)......................................................................................... 47
Option menu items............................................................................................................................................................... 47
CONFIGURATIONS 51
Configuring various functions (Setup Menu)....................................... 51
Setup menu items................................................................................................................................................................. 52
Speaker...................................................................................................................................................................................... 54
HDMI........................................................................................................................................................................................... 57
Sound......................................................................................................................................................................................... 59
ECO............................................................................................................................................................................................. 61
Function.................................................................................................................................................................................... 62
Bluetooth.................................................................................................................................................................................. 64
Language.................................................................................................................................................................................. 65
Configuring the system settings (ADVANCED SETUP menu).............. 66
ADVANCED SETUP menu items........................................................................................................................................ 66
Changing the speaker impedance setting (SP IMP.)................................................................................................. 66
Selecting the remote control ID (REMOTE ID)............................................................................................................. 67
Changing the FM/AM tuning frequency setting (TU)............................................................................................... 67
Switching the video signal type (TV FORMAT)............................................................................................................ 67
Selecting the HDMI 4K signal format (4K MODE)....................................................................................................... 68
Restoring the default settings (INIT)............................................................................................................................... 68
Updating the firmware (UPDATE).................................................................................................................................... 68
Checking the firmware version (VERSION)................................................................................................................... 68
APPENDIX 69
Frequently asked questions................................................................... 69
Troubleshooting..................................................................................... 70
First, check the following:................................................................................................................................................... 70
Power, system and remote control................................................................................................................................. 70
Audio.......................................................................................................................................................................................... 71
Video.......................................................................................................................................................................................... 73
FM/AM radio............................................................................................................................................................................ 74
USB.............................................................................................................................................................................................. 74
Bluetooth®................................................................................................................................................................................ 75
Error indications on the front display................................................... 76
Glossary................................................................................................... 77
Audio information................................................................................................................................................................. 77
HDMI and video information............................................................................................................................................. 78
Yamaha technologies.......................................................................................................................................................... 78
Supported devices and file formats...................................................... 79
Supported devices................................................................................................................................................................ 79
File formats.............................................................................................................................................................................. 79
Video signal flow.................................................................................... 79
Information on HDMI.............................................................................. 80
HDMI Control.......................................................................................................................................................................... 80
Audio Return Channel (ARC)............................................................................................................................................. 82
HDMI signal compatibility.................................................................................................................................................. 82
Trademarks............................................................................................. 83
Specifications.......................................................................................... 84
En
3
BEFORE USING THE UNIT
Accessories
Check that the following accessories are supplied with the product.
£ AM antenna £ FM antenna
* One of the above is supplied depending on
the region of purchase.
£ YPAO microphone £ Remote control
£ Batteries (AAA, R03, UM-4) (x2)
£ CD-ROM (Owner's Manual
)
£ Quick Start Guide
How to use this manual
Some features are not available in certain regions.
Due to product improvements, specifications and appearance are subject to
change without notice.
This manual explains operations using the supplied remote control.
Notice:
Indicates precautions for use to avoid the possibility of malfunction/damage to the unit.
Note:
Indicates instructions and supplementary explanations for optimum use.
Remote control
The supplied remote control is used as follows.
Insert the batteries
Insert the batteries the right way round.
Operating range of the remote control
Point the remote control at the remote control sensor on the unit and remain within the
operating range shown below.
Within 6 m (20 ft)
30° 30°
En
4
FEATURES
What you can do with the unit
The unit is equipped with full of useful functions.
Supports 2- to 5.1-channel speaker system
You can enjoy your favorite acoustic spaces in various styles.
YPAO automatically optimizes the speaker settings to suit your room.
“Optimizing the speaker settings automatically (YPAO)” (p.25)
CINEMA DSP allows you to create stereo or multichannel sounds with
the sound fields like actual movie theaters and concert halls in your
own room.
“Enjoying sound field effects (CINEMA DSP)” (p.33)
You can enjoy compressed music with enhanced sound (Compressed
Music Enhancer).
“Playing back digitally compressed formats (such as MP3, etc.) with enriched sound
(Compressed Music Enhancer)”
(p.36)
Change the input source and favorite settings with
one touch (SCENE)
The SCENE function allows you to select the input source and settings registered to
the corresponding scene, such as sound program and Compressed Music Enhancer
on/off, with just one touch.
“Selecting the input source and favorite settings with one touch (SCENE)” (p.31)
4K Ultra HD signal and HDCP 2.2 supported
You can enjoy the high definition video quality of 4K with HDCP 2.2 that complies with
the latest copyright protection.
“Selecting the HDMI 4K signal format (4K MODE)” (p.68)
The ECO mode (power saving function) allows you to
create an eco-friendly home theater system
When the ECO mode is enabled, you can reduce the unit's power consumption.
“ECO Mode” (p.61)
Sequential operation of a TV, AV receiver, and
BD/DVD player (HDMI Control)
When the unit is connected to an HDMI Control-compatible TV and BD/DVD player
with each HDMI cable, you can control the unit (such as power and volume) and
BD/DVD player with TV remote control operations.
“HDMI Control” (p.80)
Supports Bluetooth® devices
You can play back music stored on a Bluetooth device.
“Playing back music stored on a Bluetooth
®
device” (p.42)
Supports USB storage devices
You can play back music stored on a USB storage device.
“Playing back music stored on a USB storage device” (p.44)
Connecting various devices
A number of HDMI jacks and various input/output jacks on the unit allow you to
connect video devices (such as BD/DVD players), audio devices (such as CD
players), game consoles, portable audio player, and other devices.
“Connecting a TV/playback devices” (p.18)
En
5
Playing back TV audio in surround sound with a
single HDMI cable connection (Audio Return
Channel: ARC)
When using an ARC-compatible TV, you only need one HDMI cable to enable video
output to the TV, audio input from the TV, and the transmission of HDMI Control
signals.
“Connecting a TV” (p.19)
Surround playback with 5 speakers placed in front
You can enjoy the surround sound even when the surround speakers are placed in
front.
“Enjoying sound field effects without surround speakers (Virtual CINEMA
DSP)” (p.34)
Enhanced bass reproduction
Extra Bass allows you to enjoy enhanced bass reproduction that does not depend on
the speakers used.
“Enhancing the bass (Extra Bass)” (p.36)
Listening to FM/AM radio
The unit is equipped with a built-in FM/AM tuner. You can register up to 40 favorite
radio stations as presets.
“Listening to FM/AM radio” (p.37)
Easy operation with a TV screen
You can operate the USB storage device, view information, or easily configure the
settings using the on-screen menu.
Auto Rename function
The unit creates an input source name, displayed on the front display, automatically
according to the connected HDMI-compatible device.
“Input Rename” (p.62)
Useful applications
The useful application for connections and operations of the unit is as follows.
n
Application for tablets “AV SETUP GUIDE”
AV SETUP GUIDE is an application that assists you with cable connections
between AV Receiver
and source devices as well as AV Receiver setup. This
app guides you through the various settings such as speaker connections, TV
and source device connections.
Functions:
1) Connection support guide
– Speaker connection
– TV/source devices connection
2) Setup support guide
– Various setup assistance with illustrations.
– YPAO setting guidance
3) View Owner's Manual
* This application is for tablets only.
For details, search for “AV SETUP GUIDE” on the App Store or Google Play™.
En
6
Part names and functions
The part names and functions of the unit and the supplied remote control are as follows.
Front panel
YPAO MIC
INFO
MEMORY
(
PAIRING
)
PRESET
FM AM
TUNING
PHONES
SILENT
CINEMA
VOLUME
AUX
TONE
CONTROL
STRAIGHT
TV
BD
DVD
CD
RADIO
INPUT
PROGRAM
SCENE
AUDIO
USB
4 05 631 7 8 9
A
C E F
IG HB D
2
1
z (power) key
Turns on/off (standby) the unit.
2
Standby indicator
Lights up when the unit is in Bluetooth Standby enable
condition (p.64).
3
YPAO MIC jack
For connecting the supplied YPAO microphone (p.25).
4
Remote control sensor
Receives remote control signals (p.4).
5
INFO key
Selects the information displayed on the front display
(p.30).
6
MEMORY (PAIRING) key
Registers FM/AM radio stations as preset stations (p.38).
Starts pairing with a Bluetooth device by holding down for 3
seconds (p.42).
7
PRESET keys
Select a preset FM/AM radio station (p.40).
8
FM and AM keys
Switch between FM and AM (p.37).
9
TUNING keys
Select the radio frequency (p.37).
:
Front display
Displays information (p.8).
A
PHONES jack
For connecting headphones.
B
INPUT keys
Select an input source.
C
TONE CONTROL key
Adjusts the level of high-frequency range (Treble) and low-
frequency range (Bass
) individually (p.48).
D
SCENE keys
Select the registered input source and sound program with
one touch. Also, turns on the unit when it is in standby
mode (p.31).
E
PROGRAM keys
Select a sound program or a surround decoder (p.32).
F
STRAIGHT key
Enables/disables the straight decode mode (p.35).
G
AUX jack
For connecting devices, such as portable audio players
(p.22).
H
USB jack
For connecting a USB storage device (p.44).
I
VOLUME knob
Adjusts the volume.
En
7
Front display (indicators)
-
R
es
Hi
YPAO
VOL.
PARTY
ZONE
FPR
SBL SB SBR
FPL
VIRTUAL
3 B2 A
LINK
MASTER
2
ENHANCER
ECO
OUT
A
-
DRC
SLEEP
STEREO
TUNED
VOL.
SL
SW
SR
MUTE
1 3 5 6
2 74
98 9
A0 B C
1
HDMI
Lights up when HDMI signals are being input or output.
OUT
Lights up when HDMI signals are being output.
2
Bluetooth indicator
Light up while the unit is connected to a Bluetooth device.
3
CINEMA DSP
Lights up when CINEMA DSP (p.33) is working.
4
SLEEP
Lights up when the sleep timer is on.
5
STEREO
Lights up when the unit is receiving a stereo FM radio
signal.
TUNED
Lights up when the unit is receiving an FM/AM radio station
signal.
6
A-DRC
Lights up when Adaptive DRC (p.48) is working.
7
Volume indicator
Indicates the current volume.
8
ECO
Lights up when the eco mode (p.61) is enabled.
9
Cursor indicators
Indicate the remote control cursor keys currently
operational.
:
Information display
Displays the current status (such as input name and sound
mode name). You can switch the information by pressing
INFO (p.
30).
A
ENHANCER
Lights up when Compressed Music Enhancer (p.36) is
working.
B
Speaker indicators
Indicate speaker terminals from which signals are output.
A Front speaker (L)
S Front speaker (R)
D Center speaker
F Surround speaker (L)
G Surround speaker (R)
L Subwoofer
C
MUTE
Blinks when audio is temporarily muted.
En
8
Rear panel
8 95 7
2
1
3
6
4
The area around the video/audio output jacks is marked in white
on the actual product to prevent improper connections.
1
HDMI OUT jack
For connecting to an HDMI-compatible TV and outputting
video/audio signals (
p.18). When using ARC, TV audio
signal can also be input through the HDMI OUT jack.
2
HDMI 1–4 jacks
For connecting to HDMI-compatible playback devices and
inputting video/audio signals (
p.20).
3
ANTENNA jacks
For connecting to FM and AM antennas (p.23).
4
Power cable
For connecting to an AC wall outlet (p.23).
5
AV jacks
AUDIO jacks
For connecting to video/audio playback devices and
inputting video/audio signals (
p.20).
6
MONITOR OUT jacks
For connecting to a TV and outputting video signals
(p.18).
7
SUBWOOFER PRE OUT jack
For connecting to a subwoofer (with built-in amplifier)
(p.16).
8
SPEAKERS terminals
For connecting to speakers (p.16).
9
VOLTAGE SELECTOR
(Taiwan, Brazil and General models only)
Selects the switch position according to your local voltage
(p.23).
En
9
Remote control
TUNING
PRESET
MUTE
TUNING
MEMORY
TOP MENU
HOME
POP-UP/MENU
DISPLAYRETURN
SETUP
OPTION
ENTER
FM/AM
VOLUME
PROG RAM
USB
STRAIGHT
ENHANCER BASS
BLUETOOTH
INPUT
BD
DVD
TV
CD
S C E NE
RADIO
SLEEP
BLUE
YELLOWGREEN
RED
1
3
2
6
4
5
7
B
C
9
0
A
8
D
1
Remote control signal transmitter
Transmits infrared signals.
2
z (receiver power) key
Turns on/off (standby) the unit.
3
SLEEP key
Pressing this key repeatedly will specify the time (120 min,
90 min, 60 min, 30 min, off), in which the unit switches to
the standby mode.
4
SCENE keys
Select the registered input source and sound program with
one touch. Also, turn on the unit when it is in standby mode
(p.31).
5
Sound mode keys
Select a sound mode (p.32).
6
Input selection keys
Select an input source for playback.
7
SETUP key
Displays the setup menu (p.51).
8
Menu operation keys
Cursor keys
Select a menu or the parameter.
ENTER
Confirms a selected item.
RETURN
Returns to the previous screen.
89: External device operation keys
Let you perform playback operations when “USB” is
selected as the input source, or control playback of the
HDMI Control-compatible playback device.
Note
The playback devices must support HDMI Control. Some
HDMI Control-compatible devices cannot be used.
You can assign the unit's functions to the RED/GREEN/
YELLOW/BLUE keys (
p.64).
:
Radio keys
Operate the FM/AM radio when “TUNER” is selected as the
input source (p.37).
MEMORY
Registers FM/AM radio stations as
presets.
PRESET
Select a preset station.
TUNING
Select the radio frequency.
A
VOLUME keys
Adjust the volume.
B
MUTE key
Mutes the audio output.
C
OPTION key
Displays the option menu (p.47).
D
DISPLAY key
Turns on/off the browse screen, playback screen, etc.
En
10
PREPARATIONS
General setup procedure
1 Placing speakers................................................................................................................................ (p.12)
2 Connecting speakers........................................................................................................................ (p.16)
3 Connecting a TV/playback devices.................................................................................................. (p.18)
4 Connecting the FM/AM antennas.................................................................................................... (p.23)
5 Connecting the power cable............................................................................................................ (p.23)
6 Selecting an on-screen menu language.......................................................................................... (p.24)
7 Optimizing the speaker settings automatically (YPAO)................................................................ (p.25)
This completes all the preparations. Enjoy playing movies, music, radio and other content with the unit!
En
11
1 Placing speakers
Select the speaker layout for the number of speakers that you are using and place the speakers and subwoofer in your room. This section describes the representative speaker
layout examples.
Notice
(U.S.A. and Canada models only)
Under its default settings, the unit is configured for 8-ohm speakers. When connecting 6-ohm speakers, set the unit’s speaker impedance to “6
Ω MIN”. For details, see “Setting the speaker impedance” (p.15).
(Except for U.S.A. and Canada models)
Use speakers with an impedance of at least 6 W.
Use a subwoofer with built-in amplifier.
Be sure to connect the front left and right speakers.
En
12
Typical speaker layouts
n
5.1-channel system
We recommend this speaker layout which can maximize the performance of the unit.
1 to 30° 1 to 30°
Speaker type Abbr. Function
Front (L/R)
1/2
Produce front left/right channel sounds (stereo sounds).
Center
3
Produces center channel sounds (such as movie dialogue
and vocals).
Surround (L/R)
4/5
Produce surround left/right channel sounds.
Subwoofer
9
Produces LFE (low-frequency effect) channel sounds and
reinforces the bass parts of other channels.
This channel is counted as “0.1”.
Note
You can enjoy surround sound even without the center speaker (4.1-channel system).
You can place the subwoofer either in the left or right side.
n
5.1-channel system (Virtual CINEMA FRONT)
We recommend this speaker layout when the speakers can't be placed in back of the
room.
1 2
39
4 5
Speaker type Abbr. Function
Front (L/R)
1/2
Produce front left/right channel sounds (stereo sounds).
Center
3
Produces center channel sounds (such as movie dialogue
and vocals).
Surround (L/R)
4/5
Produce surround left/right channel sounds. By this
system, place the surround speakers in front.
Subwoofer
9
Produces LFE (low-frequency effect) channel sounds and
reinforces the bass parts of other channels.
This channel is counted as “0.1”.
Note
To utilize this configuration, set “Virtual CINEMA FRONT” (p.55) in the “Setup” menu to “On”.
You can enjoy surround sound even without the center speaker (front 4.1-channel system).
You can place the subwoofer either in the left or right side.
En
13
Other speaker layouts
The following speaker layouts are also available.
n
3.1-channel system
1 2
39
n
2.1-channel system
1 2
9
En
14
Setting the speaker impedance
(U.S.A. and Canada models only)
Under its default settings, the unit is configured for 8-ohm speakers. When connecting
6-ohm speakers, set the speaker impedance to “6 Ω MIN”.
1
Before connecting speakers, connect the power cable to an AC
wall outlet.
2
While holding down STRAIGHT on the front panel, press z
(power).
(power)
z
STRAIGHT
3
Check that “SP IMP.” is displayed on the front display.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
VOL .
FPR
SL
SW
SR
SBL SB SBR
FPL
MUT E VIRT UAL
SP IMP.8¬MIN
4
Press STRAIGHT to select “6 Ω MIN”.
5
Press z (power) to set the unit to standby mode and remove the
power cable from the AC wall outlet.
You are now ready to connect the speakers.
En
15
2 Connecting speakers
Connect the speakers placed in your room to the unit. The following diagrams provide connections for a 5.1-channel system as an example. For other systems, connect speakers
while referring to the connection diagram for the 5.1-channel system.
Notice
Remove the unit’s power cable from an AC wall outlet and turn off the subwoofer before connecting the speakers.
The speaker has the polarity (+/-). Connect the speaker cable correctly between the positive (+) terminal of the unit and the speaker, and also between the negative (-) terminal of them.
Cables required for connection (commercially available)
Speaker cables (x the number of speakers)
+
+
Audio pin cable (x1: for connecting a subwoofer)
9
3
45
12
10 mm
(3/8”)
Audio pin cable
Use a subwoofer with built-in amplifier.
Subwoofer
Surround (L)Surround (R) Center Front (R) Front (L)
10 mm
(3/8”)
Precaution for connecting of the speaker cables
Prepare speaker cables in a place away from the unit, to avoid
accidentally dropping wire strands into the unit's interior which could
result in a short circuit or malfunction of the unit.
Improper connecting of the speaker cables may cause short circuit and
also damage the unit or the speakers.
Twist the bare wires of the speaker cables
firmly together.
Do not let the bare wires of the speaker
cable touch one another.
Do not let the bare wires of the speaker
cable come into contact with the unit’s
metal parts (rear panel and screws).
If “Check SP Wires” appear on the front display when the unit is turned
on, turn off the unit, and then check the speaker cables short circuit.
En
16
Connecting speaker cables
Speaker cables have two wires. One is for connecting the negative (-) terminals of the
unit and the speaker to each other, and the other is for the positive (+) terminals. If the
wires are colored to prevent confusion, connect the black wire to the negative and the
other wire to the positive terminal.
n
Connecting front speakers
1
Remove approximately 10 mm (3/8”) of insulation from the ends of
the speaker cable, and twist the bare wires of the cable firmly
together.
2
Loosen the speaker terminal.
3
Insert the bare wires of the cable into the gap on the side (upper
right or bottom left) of the terminal.
4
Tighten the terminal.
FRONT
aa
b
d
c
+ (red)
- (black)
Using a banana plug
(U.S.A., Canada, Taiwan, Brazil and General models only)
1
Tighten the speaker terminal.
2
Insert a banana plug into the end of the terminal.
FRONT
a
b
Banana plug
n
Connecting center/surround speakers
1
Remove approximately 10 mm (3/8”) of insulation from the ends of
the speaker cable, and twist the bare wires of the cable firmly
together.
2
Press down the tab.
3
Insert the bare wires of the cable into the hole in the terminal.
4
Release the tab.
CENTER
SURROUND
aa
b
c
d
+ (red)
- (black)
Connecting the subwoofer (with built-in amplifier)
Use an audio pin cable to connect the subwoofer.
Audio pin cable
En
17
3 Connecting a TV/playback devices
The unit is equipped with a variety of input jacks
including HDMI input jacks to allow you to connect
different types of playback devices. For information on
how to connect a Bluetooth device or a USB storage
device, see the following pages.
Connecting a Bluetooth device (p.42)
Connecting a USB storage device (p.44)
Input/output jacks and cables
n
Video/audio jacks
HDMI jacks
Transmit digital video and digital sound through a
single jack. Use an HDMI cable.
HDMI cable
Note
Use a 19-pin HDMI cable with the HDMI logo. We
recommend using a cable less than 5.0 m (16.4 ft) long to
prevent signal quality degradation.
The unit’s HDMI jacks support the HDMI Control, Audio
Return Channel (ARC), and 3D and 4K Ultra HD video
transmission (through output) features.
Use a Premium High Speed HDMI Cable or Premium High
Speed Cable with Ethernet to enjoy 3D or 4K Ultra HD videos.
n
Video jacks
VIDEO jacks
Transmit analog video signals. Use a video pin
cable.
Video pin cable
n
Audio jacks
OPTICAL jack
Transmit digital audio signals. Use a digital optical
cable. If there is a protective cap on the tip of the
cable, remove it before using the cable.
OPTICAL
Digital optical cable
COAXIAL jacks
Transmit digital audio signals. Use a digital coaxial
cable.
Digital coaxial cable
AUDIO jacks
(Stereo L/R jacks)
Transmit analog stereo audio signals. Use a stereo
pin cable (RCA cable).
Stereo pin cable
(Stereo mini jack)
Transmits analog stereo audio signals. Use a
stereo mini-plug cable.
Stereo mini-plug cable
En
18
Connecting a TV
Connect a TV to the unit so that video input to the unit can be output to the TV. You
can also enjoy playback of TV audio on the unit.
To maximize the performance of the unit, we recommend connecting a TV with an
HDMI cable.
n
HDMI connection
Connect the TV to the unit with an HDMI cable and a digital optical cable.
HDMI
OPTICAL
HDMI
OPTICAL
OPTICAL
HDMI
HDMI
HDMI
HDMI
O OO O
The unit (rear)
AUDIO 1 (OPTICAL) jack
HDMI OUT jack HDMI input
Audio output
(digital optical)
TV
Note
A digital optical cable connection allows audio from the TV to be played back on the unit. A digital optical
cable connection is not needed in the following cases:
If your TV supports Audio Return Channel (ARC)
If you will receive TV broadcasts only from the set-top box
If you connect a TV that supports HDMI Control to the unit with an HDMI cable, you can control the unit’s
power and volume with the TV’s remote control.
To use HDMI Control and ARC, you need to configure the HDMI settings on the unit.
For details on the settings, see “Information on HDMI”
(p.80).
About Audio Return Channel (ARC)
ARC allows audio signals to travel both ways. If you connect a TV that supports ARC to the unit with a
single HDMI cable, you can output video/audio to the TV or input TV audio to the unit.
When using ARC, connect a TV with an HDMI cable that supports ARC.
n
Composite video connection
When connecting any video device with a video pin cable, connect the TV to the
MONITOR OUT
(VIDEO) jack.
Note
If you connect your TV to the unit with a cable other than HDMI, video input to the unit via HDMI cannot be
output to the TV.
Operations with TV screen are available only when your TV is connected to the unit via HDMI.
If you will receive TV broadcasts only from the set-top box, you do not need to make an audio cable
connection between the TV and the unit.
VIDEO (composite video) connection
Connect the TV to the unit with a video pin cable and a digital optical cable.
VIDEO
OPTICAL
O O
MONITOR
OUT
V
V
The unit (rear)
AUDIO 1 (OPTICAL) jack
MONITOR OUT (VIDEO) jack
Video input
(composite video)
Audio output
(digital optical)
TV
En
19
Connecting video devices (such as BD/DVD players)
Connect video devices such as BD/DVD players, set-top boxes (STBs) and game
consoles to the unit. Depending on the video/audio output jacks available on your
video device, choose one of the following connections. We recommend using an
HDMI connection if the video device has an HDMI output jack.
Note
If the combination of video/audio input jacks available on the unit does not match your video device, change
its combination according to the output jacks of your device (p.21).
n
HDMI connection
Connect a video device to the unit with an HDMI cable.
HDMI
HDMI
HDMI
The unit (rear)
HDMI OUT jack
HDMI 1–4 jacks
Video device
If you select HDMI 1–4 as the input source by pressing INPUT, the video/audio played
back on the video device will be output from the unit.
Note
To watch videos input to the HDMI 1–4 jacks, you need to connect your TV to the HDMI OUT jack of the unit
(p.19).
n
Composite video connection
Connect a video device to the unit with a video pin cable and an audio cable (digital
coaxial or stereo pin cable). Choose a set of input jacks (on the unit) depending on the
audio output jacks available on your video device.
Output jacks on video device
Input jacks on the unit
Video Audio
Composite video
Digital coaxial AV 1 (VIDEO + COAXIAL)
Analog stereo AV 2–3 (VIDEO + AUDIO)
Digital optical
You need to change the combination
of video/audio input jacks (p.21).
R
L
R
L
COAXIAL
VIDEO
VIDEO
C C
L
R
L
R
V
V
COAXIAL
The unit (rear)
AV 1 (COAXIAL) jack or AV 2–3
(AUDIO) jacks
AV 1–3 (VIDEO) jacks
Video output
(composite video)
Audio output
(digital coaxial or analog
stereo)
Video device
If you select AV 1-3 as the input source by pressing INPUT, the video/audio played
back on the video device will be output from the unit.
Note
To watch videos input to the AV 1–3 (VIDEO) jacks, you need to connect your TV to the MONITOR OUT
(VIDEO) jack of the unit (p.19).
En
20
n
Changing the combination of video/audio input jacks
If the combination of video/audio input jacks available on the unit does not match your
video device, change its combination according to the output jacks of your device.
You can connect a video device that has the following video/audio output jacks.
Output jacks on video device Input jacks on the unit
Video Audio Video Audio
HDMI
Digital optical HDMI 1–4 AUDIO 1 (OPTICAL)
Digital coaxial HDMI 1–4
AUDIO 2 (COAXIAL)
AV 1 (COAXIAL)
Analog stereo HDMI 1–4 AV 2–3 (AUDIO)
Composite video Digital optical AV 1–3 (VIDEO) AUDIO 1 (OPTICAL)
Necessary setting
For example, if you have connected a video device to AV 2 (VIDEO) and AUDIO 1
(OPTICAL) jack of the unit, change the combination setting as follows.
VIDEO
OPTICAL
V
V
O O
The unit (rear)
AUDIO 1 (OPTICAL) jack
AV 2 (VIDEO) jack
Video output
(composite video)
Audio output
(digital optical)
Set-top box
1
After connecting external devices (such as a TV and playback
devices) and power cable of the unit, turn on the unit.
2
Press INPUT to select “AV 2” (video input jack to be used) as
the input source.
3
Press OPTION.
MUTE
TOP MENU
HOME
POP-UP/MENU
DISPLAYRETURN
SETUP
OPTION
ENTER
TUNING
PRESET
MUTE
TUNING
MEMORY
TOP MENU
HOME
POP-UP/MENU
DISPLAYRETURN
SETUP
OPTION
ENTER
FM/AM
VOLUME
PROGR AM
USB
STRAIGHT
ENHANCER BASS
BLUETOOTH
INPU T
BD
DVD
TV
CD
SC ENE
RADIO
SLEEP
BLUE
YELLOWGREEN
RED
MUT
E
TO
P MENU
HOME
POP-UP/MENU
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
DISPLADISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLADISPLA
DISPLADISPLA
DISPLADISPLA
DISPLADISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURNRETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
SETU
P
P
OPTION
ENTER
Cursor keys
4
Use the cursor keys (q/w) to select “Audio In” and press
ENTER.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
FPR
SL
SW
SR
SBL SB SBR
FPL
MUT E V IRT UAL
VOL .
Audio In
5
Use the cursor keys (e/r) to select “AUDIO 1” (audio input
jack to be used).
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
FPR
SL
SW
SR
SBL SB SBR
FPL
MUT E V IRT UAL
VOL .
AudioAUDIO1
6
Press OPTION.
This completes the necessary settings.
If you select “AV 2” as the input source by pressing INPUT, the video/audio
played back on the video device will be output from the unit.
En
21
Connecting audio devices (such as CD players)
Connect audio devices such as CD players and MD players to the unit. Depending on
the audio output jacks available on your audio device, choose one of the following
connections.
Audio output jacks on audio device Audio input jacks on the unit
Digital optical AUDIO 1 (OPTICAL)
Digital coaxial
AUDIO 2 (COAXIAL)
AV 1 (COAXIAL)
Analog stereo AV 2–3 (AUDIO)
R
L
COAXIAL
OPTICAL
(TV)
R
L
COAXIAL
OPTICAL
C C
L
R
L
R
O O
The unit (rear)
AV 1–3 jacks
AUDIO 1–2 jacks
Audio output
(either digital optical, digital coaxial,
or analog stereo)
Audio device
If you select AV 1-3 or AUDIO 1-2 as the input source by pressing INPUT, the audio
played back on the audio device will be output from the unit.
Connecting to the jack on the front panel
Use the AUX jack on the front panel to temporarily connect devices such as portable
audio players to the unit.
Before making a connection, stop playback on the device and turn down the volume
on the unit.
AUX
TONE
CONTROL
STRAIGHT
TV
BD
DVD
CD
RADIO
INPUT
PROGRAM
AUDIO
USB
The unit (front)
Portable audio player
If you select “AUX” as the input source by pressing INPUT, the audio played back on
the device will be output from the unit.
Note
You need to prepare the audio cable that matches the output jacks on your device.
For details on how to connect a USB storage device, see “Connecting a USB storage device” (p.44).
En
22
4 Connecting the FM/AM antennas
Connect the supplied FM/AM antennas to the unit.
Fix the end of the FM antenna to a wall, and place the AM antenna on a flat surface.
The unit (rear)
FM antenna
AM antenna
Assembling and connecting the AM antenna
ReleaseHold down Insert
Note
Unwind only the length of cable needed from the AM antenna unit.
The wires of the AM antenna have no polarity.
5 Connecting the power cable
Warning
(Taiwan, Brazil and General models only)
Make sure you set VOLTAGE SELECTOR of the unit BEFORE plugging the power cable into an AC wall
outlet. Improper setting of
VOLTAGE SELECTOR
may cause damage to the unit and create a potential
fire hazard.
Before connecting the power cable
Set the switch position of VOLTAGE SELECTOR according to your local voltage. Voltages are AC 110–
120/220–240 V, 50/60 Hz.
VOLTAGE
SELECTOR
110V
120V
220V
240V
The unit (rear) VOLTAGE SELECTOR
After all the connections are complete, plug in the power cable.
The unit (rear)
To an AC wall outlet
En
23
6 Selecting an on-screen menu language
Select the desired on-screen menu language.
1
Press z (receiver power) to turn on the unit.
2
Turn on the TV and switch the TV input to display video from the
unit (HDMI OUT jack).
Note
Operations with TV screen are available only when your TV is connected to the unit via HDMI. If
not, carry out operations while viewing the front display.
3
Press SETUP.
4
Use the cursor keys to select “Language” and press ENTER.
5
Use the cursor keys to select the desired language.
6
To exit from the menu, press SETUP.
Note
The information on the front display is provided in English only.
En
24
7 Optimizing the speaker settings automatically (YPAO)
The Yamaha Parametric room Acoustic Optimizer (YPAO) function detects speaker
connections, measures the distances from them to your listening position(s), and then
automatically optimizes the speaker settings, such as volume balance and acoustic
parameters, to suit your room.
Note
When you use the front 5.1-channel speaker (Virtual CINEMA FRONT) configuration (p.13), set “Virtual
CINEMA FRONT” (p.55) in the “
Setup
” menu to “On” beforehand.
Please note the following when using YPAO.
Use YPAO after connecting a TV and speakers to the unit.
During the measuring process, test tones are output at high volume. Ensure that the test tones do not
frighten small children.
During the measuring process, you cannot adjust the volume.
During the measuring process, keep the room as quiet as possible.
Do not connect headphones.
Do not stand between the speakers and the YPAO microphone during the measurement process (about
3 minutes).
1
Press z (receiver power) to turn on the unit.
2
Turn on the TV and switch the TV input to display video from the
unit (HDMI OUT jack).
Note
Operations with TV screen are available only when your TV is connected to the unit via HDMI. If
not, carry out operations while viewing the front display.
3
Turn on the subwoofer and set the volume to half. If the crossover
frequency is adjustable, set it to maximum.
VOLUME HIGH CUT
CROSSOVER/
MIN MAXMIN MAX
9
4
Place the YPAO microphone at your listening position and
connect it to the YPAO MIC jack on the front panel.
Note
Place the YPAO microphone at your listening position (same height as your ears). We recommend
the use of a tripod as a microphone stand. You can use the tripod screws to stabilize the
microphone.
1 2
3
9
4 5
The unit (front)
Ear height
The following screen appears on the TV.
En
25
5
To start the measurement, use the cursor keys to select “Start”
and press ENTER.
The measurement will start in 10 seconds. Press ENTER to start the
measurement immediately.
Note
To stop the measurement temporarily, press RETURN and follow the procedure in “Error
messages”
(p.27).
The following screen appears on the TV when the measurement finishes.
1
2
3
4
1
The number of speakers (front side/rear side/subwoofer)
2
Speaker distance (nearest/farthest)
3
Adjustment range of speaker output level
4
Warning message (if available)
Note
If any error message (such as E-1) or warning message (such as W-1) appears, see “Error
messages”
(p.27)
or “Warning messages” (p.28).
A speaker with a problem is indicated by blinking of the speaker indicators in the front display.
If multiple warnings are given (when operating with the front display), use the cursor keys (q/w)
to check the other warning messages.
6
Confirm the results displayed on the screen and press ENTER.
7
Use the cursor keys (e/r) to select “SAVE” and press ENTER.
The adjusted speaker settings are applied.
Note
To finish the measurement without saving the result, select “CANCEL”.
8
Disconnect the YPAO microphone from the unit.
This completes optimization of the speaker settings.
Notice
The YPAO microphone is sensitive to heat, so should not be placed anywhere where it could be
exposed to direct sunlight or high temperatures (such as on top of AV equipment).
En
26
Error messages
If any error message is displayed during the measurement, resolve the problem and
perform YPAO again.
Error message
TV screen
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
FPR
SBL SB SBR
FPL
MUT E V IRT UAL
E-5:NOISY
VOL .
SL
SW
SR
E-5:NOISY
Front display
n
Procedure to handle errors
1
Check the content of error message and press ENTER.
2
Use the cursor keys (e/r) to select the desired operation.
To exit the YPAO measurement:
1
Select “EXIT” and press ENTER.
2
Use the cursor keys (q/w) to select “Exit” and press ENTER.
3
Disconnect the YPAO microphone from the unit.
To retry the YPAO measurement from beginning:
1
Select “RETRY” and press ENTER.
To proceed with the current YPAO measurement (for E-5 and E-9
only):
1
Select “PROCEED” and press ENTER.
Error message Cause Remedy
E-1:No Front SP
(E-1:NO FRNT SP)
Front speakers are not
detected.
Exit YPAO, turn off the unit, and then
check the speaker connections.
E-2:No Sur. SP
(E-2:NO SUR SP)
One of the surround
speakers cannot be
detected.
E-5:Noisy
(E-5:NOISY)
The noise is too loud.
Keep the room quiet and retry YPAO. If
you select “PROCEED”, YPAO takes the
measurement again and ignores any
noise detected.
E-7:No MIC
(E-7:NO MIC)
The YPAO microphone has
been removed.
Connect the YPAO microphone to the
YPAO MIC
jack firmly and retry YPAO.
E-8:No Signal
(
E-8:NO SIGNAL)
The YPAO microphone
cannot detect test tones.
Connect the YPAO microphone to the
YPAO MIC
jack firmly and retry YPAO. If
this error occurs repeatedly, contact the
nearest authorized Yamaha dealer or
service center.
E-9:User Cancel
(E-9:CANCEL)
The measurement has been
canceled.
Retry or exit YPAO as necessary.
E-10:Internal Err.
(E-10:INTERNAL)
An internal error has
occurred.
Exit YPAO, and turn off and on the unit. If
this error occurs repeatedly, contact the
nearest authorized Yamaha dealer or
service center.
Note
Texts in parentheses denote indicators on the front display.
En
27
Warning messages
If a warning message is displayed after the measurement, you can still save the
measurement results by following on-screen instructions.
However, we recommend you perform YPAO again in order to use the unit with the
optimal speaker settings.
Warning message
TV screen
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
FPR
SBL SB SBR
FPL
MUT E V IRT UAL
VOL .
SL
SW
SR
W-1:PHASE
Problem speaker (blinks)
Front display
n
Procedure to handle warnings
1
Check the content of warning message and press ENTER.
2
Use the cursor keys (e/r) to select the desired operation.
To save the measurement results:
1
Select “SAVE” and press ENTER.
To discard the measurement result:
1
Select “CANCEL” and press ENTER.
3
Disconnect the YPAO microphone from the unit.
Warning message Cause Remedy
W-1:Out of Phase
(W-1:PHASE)
A speaker cable may be
connected with the reverse
polarity (+/-).
Check the cable connections (+/-) of the
problem speaker.
If the speaker is connected incorrectly:
Turn off the unit, reconnect the speaker
cable.
If the speaker is connected correctly:
Depending on the type of speakers or
room environment, this message may
appear even if the speakers are
connected correctly. In this case, you
can ignore the message.
W-2:Over Distance
(W-2:DISTANCE)
A speaker is placed more
than 24 m (80 ft) from the
listening position.
Exit YPAO, turn off the unit, and place the
problem speaker within 24 m (80 ft) of the
listening position.
W-3:Level Error
(W-3:LEVEL)
There are significant volume
differences between the
speakers.
Check the usage environment and cable
connections (+/-) of each speaker, and
the volume of the subwoofer. If there is
any problem, exit YPAO, turn off the unit,
and then reconnect speaker cable or
correct the speaker positions. We
recommend using the same speakers or
speakers with specifications that are as
similar as possible.
Note
Texts in parentheses denote indicators on the front display.
En
28
PLAYBACK
Basic playback procedure
Enjoying playback
1
Turn on the external devices (such as a TV or BD/DVD player)
connected to the unit.
2
Use the input selection keys to select an input source.
MUTE
FM/AM
VOLUME
PROG RAM
USB
BLUETOOTH
INPUT
TUNING
PRESET
MUTE
TUNING
MEMORY
TOP MENU
HOME
POP-UP/MENU
DISPLAYRETURN
SETUP
OPTION
ENTER
FM/AM
VOLUME
PROGR AM
USB
STRAIGHT
ENHANCER BASS
BLUETOOTH
INPU T
BD
DVD
TV
CD
SC ENE
RADIO
SLEEP
BLUE
YELLOWGREEN
RED
PR
OG R
AM
VOLUME
MUTE
Input selection keys
3
Start playback on the external device or select a radio station.
Refer to the instruction manual for the external device.
For details on the following operations, see the corresponding pages.
“Listening to FM/AM radio” (p.37)
“Playing back music stored on a Bluetooth
®
device” (p.42
)
“Playing back music stored on a USB storage device” (p.44)
4
Press VOLUME to adjust the volume.
Note
To mute the audio output, press MUTE. Press MUTE again to unmute.
To adjust the treble/bass settings, use the “Option” menu or TONE CONTROL on the front panel
(p.48).
En
29
Switching information on the front display
1
Press INFO repeatedly to select between the various display
items.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
FPR
SBL SB SBR
FPL
MUT E V IRT UAL
VOL .
SL
SW
SR
Audio Decoder
Item name
About 3 seconds after a display item is selected, its corresponding
information appears.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
FPR
SBL SB SBR
FPL
MUT E V IRT UAL
VOL .
SL
SW
SR
DPL
Information
Note
Available items vary depending on the selected input source. The displayed item can also be
applied separately to each input source.
Currently input source Item
HDMI
AV
AUDIO
AUX
Bluetooth
Input (input source name), DSP Program (sound mode name), Audio
Decoder (decoder name*)
USB
Song (song title), Artist (artist name), Album (album name), DSP
Program (sound mode name), Audio Decoder (decoder name*)
TUNER
Frequency (frequency), DSP Program (sound mode name), Audio
Decoder (decoder name*)
(U.K. and Europe models only)
Radio Data System data is also available when the unit is tuned into a
Radio Data System broadcasting station (p.41).
* The name of the audio decoder currently activated is displayed. If no audio decoder
is activated, “Decoder Off” appears.
En
30
Selecting the input source and favorite settings with one touch (SCENE)
The SCENE function allows you to select the assigned input source, sound program,
and Compressed Music Enhancer on/off with just one touch.
Selecting a registered scene
1
Press SCENE.
The input source and settings registered to the corresponding scene are
selected. The unit turns on automatically when it is in standby mode.
TUNING
PRESET
MUTE
TUNING
MEMORY
TOP MENU
HOME
POP-UP/MENU
DISPLAYRETURN
SETUP
OPTION
ENTER
FM/AM
VOLUME
PROGR AM
USB
STRAIGHT
ENHANCER BASS
BLUETOOTH
INPU T
BD
DVD
TV
CD
SC ENE
RADIO
SLEEP
BLUE
YELLOWGREEN
RED
PROG RAM
STRAIGHT
ENHANCER BASS
BD
DVD
TV
CD
S C E NE
RADIO
SLEEP
PR
OG R
AM
ST
RA
IGHT
ENHANCER
BA
SS
SLEE
P
SCENE
By default, the following settings are registered for each scene.
SCENE
Input
HDMI1 AUDIO1 AUDIO2 TUNER
Sound program
MOVIE (Sci-Fi) STRAIGHT STRAIGHT
STEREO
(5ch Stereo
)
Compressed Music
Enhancer
Off On Off On
SCENE link playback
On On Off Off
Note
The SCENE link playback function allows you to automatically turn on the TV or start playback of an external
device connected to the unit via HDMI, in conjunction with a scene selection. To enable
SCENE link
playback, set “SCENE” (p.58) in the “Setup” menu to “On”.
Registering a scene
1
Perform the following operations to prepare the settings you want
to assign to a scene.
Select an input source (p.29)
Select a sound program (p.32) or straight decode (p.35)
Enable/disable Compressed Music Enhancer (p.36)
2
Hold down the desired SCENE key until “SET Complete” appears
on the front display.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
FPR
SBL SB SBR
FPL
MUT E V IRT UAL
VOL .
SL
SW
SR
SET Complete
En
31
Selecting the sound mode
The unit is equipped with a variety of sound programs and surround decoders that
allow you to enjoy playback sources with your favorite sound mode (such as sound
field effect or stereo playback).
TUNING
PRESET
MUTE
TUNING
MEMORY
TOP MENU
HOME
POP-UP/MENU
DISPLAYRETURN
SETUP
OPTION
ENTER
FM/AM
VOLUME
PROGR AM
USB
STRAIGHT
ENHANCER BASS
BLUETOOTH
INPU T
BD
DVD
TV
CD
SC ENE
RADIO
SLEEP
BLUE
YELLOWGREEN
RED
PROG RAM
STRAIGHT
ENHANCER BASS
BD
DVD
TV
CD
S C E NE
RADIO
SLEEP
BD
DV
D
TV
CD
S C E N
E
R
ADIO
SLEE
P
STRAIGHT
ENHANCER
BASS
PROGRAM
I want to enjoy viewing video sources such as movies, TV programs, or
games.
Select a sound program suitable for each video source by pressing PROGRAM
repeatedly (
p.33).
I want to enjoy listening to music sources or stereo playback.
Select a sound program suitable for music or stereo playback by pressing
PROGRAM
repeatedly (p.34).
I want to enjoy multichannel playback from 2-channel sources.
Select a surround decoder in the “Option” menu (p.47).
I want to enjoy unprocessed sounds in original channels.
Switch to the straight decode mode by pressing STRAIGHT (p.35).
I want to enjoy enhanced bass sounds.
Enable Extra Bass by pressing BASS (p.36).
I want to enjoy listening to compressed music.
Enable Compressed Music Enhancer by pressing ENHANCER (p.36).
This mode lets you enjoy listening to compressed music from Bluetooth devices, USB
devices, etc. as it gives the music additional depth and breadth (p.
36).
Note
The sound mode can be applied separately to each input source.
When you play back audio signals with a sampling rate of higher than 96 kHz, the straight decode mode
(p.35) is automatically selected.
You can check which speakers are currently outputting sound by looking at the speaker indicators on the
unit’s front panel (p.8).
En
32
Enjoying sound field effects (CINEMA DSP)
The unit is equipped with a variety of sound programs that utilize Yamaha’s original
DSP technology (CINEMA DSP). It allows you to easily create sound fields like actual
movie theaters or concert halls in your room.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
PARTY
TUNED
ZONE
3 B2 A
FPR
SBL SB SBR
FPL
MUT E V IRT UAL
SLEEP
STEREO
VOL .
SL
SW
SR
Sci-Fi
Sound program category
“CINEMA DSP” lights up
Sound program
Note
You can adjust the sound field effect level in “DSP Level (DSP Level)” (p.48) in the “Option” menu.
n
Sound programs suitable for movies (MOVIE)
The following sound programs are optimized for viewing video sources, such as
movies, TV programs, and games.
Standard
This program creates a sound field that emphasizes the surround feeling
without disturbing the original acoustic positioning of multichannel audio,
such as Dolby Digital and DTS. Its design is based on the concept of the
ideal movie theater, in which the audience is surrounded by beautiful
reverberations from the left, right, and rear.
Spectacle
This program delivers the scale and grandeur of spectacular movie
productions. It delivers an expansive sound space to match the
cinemascope wide-screen, and boasts a broad dynamic range,
providing everything from small delicate sounds to powerful loud booms.
Sci-Fi
This program clearly reproduces the finely elaborated sound design of
the latest Sci-Fi and SFX movies. You can enjoy a variety of
cinematographically created virtual spaces reproduced with clear
separation between dialogue, sound effects, and background music.
Adventure
This program is ideal for reproducing the sound design of action and
adventure movies precisely. The sound field restrains reverberations, but
puts emphasis on reproducing a sensation of expansiveness on both
sides, powerful space expanded widely to the left and right. The
restrained depth creates a clear and powerful space, while also
maintaining the articulation of the sounds and the separation of the
channels.
Drama
This program features stable reverberations that match a wide range of
movie genres, from serious dramas to musicals and comedies. The
reverberations are modest, but suitably stereophonic. The sound effects
and background music are reproduced with a gentle echo that does not
impinge on the articulation of the dialogue. You’ll never get tired listening
for long periods.
Mono Movie
This program reproduces monaural video sources, such as classic
movies, in an atmosphere of a good old movie theater. The program
creates a pleasant space with depth, by adding breadth and the
appropriate reverberation to the original audio.
Sports
This program allows listeners to enjoy the rich vividness of sport
broadcasts and light entertainment programs. In sports broadcasts, the
commentators’ voices are positioned clearly at the center, while the
atmosphere inside the stadium is realistically conveyed by the peripheral
delivery of the sounds of the fans in a suitable space.
Action Game
This program is suitable for action games, such as car racing and
fighting games. The reality of, and emphasis on, various effects makes
the player feel like they are right in the middle of the action, allowing for
greater concentration. Use this program in combination with Compressed
Music Enhancer for a more dynamic and strong sound field.
Roleplaying Game
This program is suitable for role-playing and adventure games. This
program adds depth to the sound field for natural and realistic
reproduction of background music, special effects, and dialogue from a
wide variety of scenes. Use this program in combination with
Compressed Music Enhancer for a clearer and more spatial sound field.
En
33
n
Sound programs suitable for music (MUSIC)
The following sound programs are optimized for listening to music sources.
Hall in Munich
This program simulates a Munich concert hall with approximately 2,500
seats that uses stylish wood for the interior finishing. Fine, beautiful
reverberations spread richly, creating a calming atmosphere. The
listener’s virtual seat is at the center left of the arena.
Hall in Vienna
This program simulates a 1700-seat, middle-sized concert hall with a
shoebox shape that is traditional in Vienna. Pillars and ornate carvings
create extremely complex reverberations from all around the audience,
producing a very full, rich sound.
Chamber
This program creates a relatively wide space with a high ceiling, like an
audience hall in a palace. It offers pleasant reverberations that are
suitable for courtly music and chamber music.
Cellar Club
This program simulates an intimate concert venue with a low ceiling and
homey atmosphere. A realistic, live sound field delivers powerful sounds
that make you feel as if you are sitting in the front row in front of a small
stage.
The Roxy Theatre
This program creates the sound field of a 460-seat rock music concert
venue in Los Angeles. The listener’s virtual seat is at the center left of the
hall.
The Bottom Line
This program creates the sound field at stage front in The Bottom Line, a
famous New York jazz club once. The floor can seat 300 people to the
left and right in a sound field offering real and vibrant sound.
Music Video
This program allows you to enjoy videos of pop, rock, and jazz concerts,
as if you were there yourself. Immerse yourself in the hot concert
atmosphere thanks to the vividness of the singers and solos on stage, a
presence sound field that emphasizes the beat of rhythm instruments,
and a surround sound field that reproduces the space of a big live hall.
n
Sound programs suitable for stereo playback (STEREO)
You can select stereo playback.
2ch Stereo
Use this program to mix down multichannel sources to 2 channels. When
multichannel signals are input, they are down mixed to 2 channels and
output from the front speakers (this program does not utilize CINEMA
DSP).
5ch Stereo
Use this program to output sound from all speakers. When you play back
multichannel sources, the unit mixes down the source to 2 channels, and
then outputs the sound from all speakers. This program creates a larger
sound field and is ideal for background music at parties.
n
Enjoying sound field effects without surround speakers
(Virtual CINEMA DSP)
If you select one of the sound programs (except 2ch Stereo and 5ch Stereo) when no
surround speakers are connected, the unit automatically creates the surround sound
field using the front-side speakers.
n
Enjoying surround sound with 5 speakers placed in
front (Virtual CINEMA FRONT)
You can enjoy the surround sound even when the surround speakers are placed in
front.
n
Enjoying surround sound with headphones (SILENT
CINEMA)
You can enjoy surround or sound field effects, like a multichannel speaker system, with
stereo headphones by connecting the headphones to the
PHONES jack and selecting
a sound program or a surround decoder.
En
34
Enjoying unprocessed playback
You can play back input sources without any sound field effect processing.
n
Playing back in original channels (straight decode)
When the straight decode mode is enabled, the unit produces stereo sound from the
front speakers for 2-channel sources such as CDs, and produces unprocessed
multichannel sounds for multichannel sources.
1
Press STRAIGHT.
Each time you press the key, the straight decode mode is enabled or
disabled.
LINK
ECO
MASTER
OUT
2
A
-
DRC
ZONE
3 B2 A
FPR
SBL SB SBR
FPL
MUT E V IRT UAL
-
SLEEP
STEREO
PARTY
TUNED
R
es
Hi
YPAO
VOL.
ENHANCER
VOL .
SL
SW
SR
STRAIGHT
n
Playing back 2-channel sources in multichannel
(surround decoder)
The surround decoder enables unprocessed multichannel playback from 2-channel
sources. When a multichannel source is input, it works the same way as the straight
decode mode.
For details on each decoder see “Glossary” (p.77).
1
Press PROGRAM repeatedly to select a surround decoder.
The previously selected surround decoder is selected. You can change
the surround decoder in “Sur.Decode
” (p.47) in the “Option” menu.
TUNING
PRESET
MUTE
TUNING
MEMORY
TOP MENU
HOME
POP-UP/MENU
DISPLAYRETURN
SETUP
OPTION
ENTER
FM/AM
VOLUME
PROGR AM
USB
STRAIGHT
ENHANCER BASS
BLUETOOTH
INPU T
BD
DVD
TV
CD
SC ENE
RADIO
SLEEP
BLUE
YELLOWGREEN
RED
PROG RAM
STRAIGHT
ENHANCER BASS
BD
DVD
TV
CD
S C E NE
RADIO
SLEEP
ST
RA
IGHT
ENHANCER
BA
SS
BD
DV
D
TV
CD
S C E N
E
R
ADIO
SLEE
P
PROGRAM
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
FPR
SBL SB SBR
FPL
MUT E V IRT UAL
VOL .
SL
SW
SR
DPL
“SUR. DECODE” appears
DPL
Uses the Dolby Pro Logic decoder suitable for all sources.
DPL Movie
Uses the Dolby Pro Logic II decoder suitable for movies.
DPL Music
Uses the Dolby Pro Logic II decoder suitable for music.
DPL Game
Uses the Dolby Pro Logic II decoder suitable for games.
Neo:6 Cinema
Uses the DTS Neo: 6 decoder suitable for movies.
Neo:6 Music
Uses the DTS Neo: 6 decoder suitable for music.
Note
You can adjust the surround decoder parameters in “DSP Parameter” (p.59) in the “Setup” menu.
En
35
Enhancing the bass (Extra Bass)
Extra Bass allows you to enjoy enhanced bass sounds, regardless of the size of the
front speakers and the presence or absence of the subwoofer.
1
Press BASS.
Each time you press the key, Extra Bass is enabled or disabled.
Note
You can also use “Extra Bass” (p.55) in the “Setup” menu to enable/disable Extra Bass.
Playing back digitally compressed formats (such as
MP3, etc.) with enriched sound (Compressed Music
Enhancer)
Compressed Music Enhancer adds depth and breadth to the sound, allowing you to
enjoy a dynamic sound close to the original sound before it was compressed. This
function can be used along with any other sound modes.
1
Press ENHANCER.
Each time you press the key, Compressed Music Enhancer is enabled or
disabled.
LINK
ECO
MASTER
OUT
2
-
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
FPR
SBL SB SBR
FPL
MUT E V IRT UAL
R
es
Hi
YPAO
VOL.
VOL .
SL
SW
SR
Enhancer On
ENHANCER
“ENHANCER” lights up
Note
Compressed Music Enhancer does not work on the following audio sources.
Signals whose sampling frequency is over 48 kHz
High-definition streaming audio
You can also use “Enhancer (Enhancer)” (p.48) in the “Option” menu to enable/disable
Compressed Music Enhancer.
En
36
Listening to FM/AM radio
You can tune into a radio station by specifying its frequency or selecting from
registered radio stations.
Note
The radio frequencies differ depending on the country or region where the unit is being used. The
explanation of this section uses a display with frequencies used in U.K. and Europe models.
If you cannot obtain good reception on the radio, adjust the direction of the FM/AM antennas.
Setting the frequency steps
(Asia, Taiwan, Brazil and General models only)
At the factory, the frequency step setting is set to 50 kHz for FM and 9 kHz for AM.
Depending on your country or region, set the frequency steps to 100 kHz for FM and
10 kHz for AM.
1
Set the unit to standby mode.
2
When holding down STRAIGHT on the front panel, press z
(power).
(power)
z
STRAIGHTPROGRAM
3
Press PROGRAM repeatedly to select “TU”.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
VOL .
FPR
SL
SW
SR
SBL SB SBR
FPL
MUT E V IRT UAL
TU••FM50/AM9
4
Press STRAIGHT to select “FM100/AM10”.
5
Press z (power) to set the unit to standby mode and turn it on
again.
Selecting a frequency for reception
1
Press FM/AM to select a band.
“TUNER” is selected as the input source and then the frequency currently
selected is displayed.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
MUT E V IRT UAL
VOL .
FM 87.50MHz
En
37
2
Press TUNING repeatedly to set a frequency.
Hold down the key for about a second to search stations automatically.
TUNING
PRESET
MUTE
TUNING
MEMORY
TOP MENU
HOME
POP-UP/MENU
DISPLAYRETURN
SETUP
OPTION
ENTER
FM/AM
VOLUME
PROGR AM
USB
STRAIGHT
ENHANCER BASS
BLUETOOTH
INPU T
BD
DVD
TV
CD
SC ENE
RADIO
SLEEP
BLUE
YELLOWGREEN
RED
TUNING
PRESET
TUNING
MEMORY
BLUE
YELLOWGREEN
RED
PRESET
MEMO
RY
BLUE
YEL
LO
W
LO
LO
GREEN
RE
D
TUNING
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
PARTY
ZONE
3 B2 A
FPR
SBL SB SBR
FPL
MUT E V IRT UAL
VOL .
SL
SW
SR
STEREO
TUNED
FM 98.50MHz
“TUNED” lights up when the unit is receiving an FM/AM radio station
signal.
“STEREO” lights up when the unit is receiving a stereo FM radio signal.
Note
You can switch between “Stereo” (stereo) and “Mono” (monaural) for FM radio reception by
selecting “
FM Mode” in the “Option” menu. When the signal reception for an FM radio station is
unstable, switching to monaural may improve it.
You can watch videos input from external devices while listening to radio by selecting the video
input jack in
“Video Out (Video Out)” (p.50) in the “Option” menu.
Registering favorite radio stations (presets)
You can register up to 40 radio stations as presets. Once you have registered stations,
you can easily tune into them by selecting their preset numbers.
n
Registering radio stations automatically (Auto Preset)
Automatically register FM radio stations with strong signals (up to 40 stations).
Note
To register AM radio stations, follow “Registering a radio station manually” (p.39).
(U.K. and Europe models only)
Only Radio Data System broadcasting stations are registered automatically by the Auto Preset function.
1
Press FM/AM to select “TUNER” as the input source.
2
Press OPTION.
3
Use the cursor keys to select “Preset” and press ENTER.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
FPR
SL
SW
SR
SBL SB SBR
FPL
MUT E V IRT UAL
VOL .
Preset
En
38
4
To start the Auto Preset process, press ENTER.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
PARTY
ZONE
3 B2 A
MUT E V IRT UAL
STEREO
TUNED
FPR
SBL SB SBR
FPL
SL
SW
SR
VOL .
01:FM 87.50MHz
“SEARCH” appears during Auto Preset
Preset number from which to start the registration
Note
To specify the preset number from which to start the registration, press cursor keys (e/r) or
PRESET to select a preset number.
To cancel the Auto Preset process, press RETURN.
When the Auto Preset process finishes, “FINISH” appears and the “Option” menu
closes automatically.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
FPR
SL
SW
SR
SBL SB SBR
FPL
MUT E V IRT UAL
VOL .
Auto Preset
n
Registering a radio station manually
Select a radio station manually and register it to a preset number.
1
Follow “Selecting a frequency for reception” (p.37) to tune into
the desired radio station.
2
Hold down MEMORY for a few seconds.
The first time that you do register a station, the selected radio station will
be registered to the preset number “01”. Thereafter, each radio station
you select will be registered to the next empty (unused) preset number
after the most recently registered number.
TUNING
PRESET
MUTE
TUNING
MEMORY
TOP MENU
HOME
POP-UP/MENU
DISPLAYRETURN
SETUP
OPTION
ENTER
FM/AM
VOLUME
PROGR AM
USB
STRAIGHT
ENHANCER BASS
BLUETOOTH
INPU T
BD
DVD
TV
CD
SC ENE
RADIO
SLEEP
BLUE
YELLOWGREEN
RED
TUNING
PRESET
TUNING
MEMORY
BLUE
YELLOWGREEN
RED
TUNING
PRESET
TUNING
BLUE
YEL
LO
W
LO
LO
GREEN
RE
D
MEMORY
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
PARTY
ZONE
3 B2 A
MUT E V IRT UAL
FPR
SBL SB SBR
FPL
VOL .
SL
SW
SR
01:FM 98.50MHz
STEREO
TUNED
Preset number
Note
To select a preset number for registering, press MEMORY once after tuning into the desired radio
station, press PRESET to select a preset number, and then press MEMORY again.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
PARTY
ZONE
3 B2 A
FPR
SBL SB SBR
FPL
MUT E V IRT UAL
SLEEP
VOL .
SL
SW
SR
02:Empty
TUNED
STEREO
“Empty” (not in use) or the frequency currently registered
En
39
n
Selecting a preset station
Tune into a registered radio station by selecting its preset number.
1
Press FM/AM to select “TUNER” as the input source.
2
Press PRESET repeatedly to select the desired radio station.
TUNING
PRESET
MUTE
TUNING
MEMORY
TOP MENU
HOME
POP-UP/MENU
DISPLAYRETURN
SETUP
OPTION
ENTER
FM/AM
VOLUME
PROGR AM
USB
STRAIGHT
ENHANCER BASS
BLUETOOTH
INPU T
BD
DVD
TV
CD
SC ENE
RADIO
SLEEP
BLUE
YELLOWGREEN
RED
TUNING
PRESET
TUNING
MEMORY
BLUE
YELLOWGREEN
RED
TUNING
TUNING
MEMO
RY
BLUE
YEL
LO
W
LO
LO
GREEN
RE
D
PRESET
ENHANCER
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
PARTY
ZONE
3 B2 A
MUT E V IRT UAL
FPR
SBL SB SBR
FPL
LINK
ECO
MASTER
OUT
2
VOL .
SL
SW
SR
STEREO
TUNED
01:FM 98.50MHz
Note
“No Presets” appears when no radio stations are registered.
n
Clearing preset stations
Clear radio stations registered to the preset numbers.
1
Press FM/AM to select “TUNER” as the input source.
2
Press OPTION.
3
Use the cursor keys to select “Preset” and press ENTER.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
FPR
SL
SW
SR
SBL SB SBR
FPL
MUT E V IRT UAL
VOL .
Preset
4
Use the cursor keys (q/w) to select “CLEAR”.
5
Use the cursor keys (e/r) to select a preset station to be cleared
and press ENTER.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
PARTY
ZONE
3 B2 A
MUT E V IRT UAL
FPR
SBL SB SBR
FPL
VOL .
SL
SW
SR
STEREO
TUNED
01:FM 98.50MHz
Preset station to be cleared
If the preset station is cleared, “Cleared” appears and then the next in-use
preset number is displayed.
01:Cleared
6
Repeat step 5 until all desired preset stations are cleared.
7
To exit from the menu, press OPTION.
En
40
Radio Data System tuning
(U.K. and Europe models only)
Radio Data System is a data transmission system used by FM stations in many
countries. The unit can receive various types of Radio Data System data, such as
“Program Service”, “Program Type”, “Radio Text
” and “Clock Time”, when it is tuned
into a Radio Data System broadcasting station.
n
Displaying the Radio Data System information
1
Tune into the desired Radio Data System broadcasting station.
Note
We recommend using “Auto Preset” to tune into the Radio Data System broadcasting stations
(p.38).
2
Press INFO repeatedly to select between the various display
items.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
PARTY
ZONE
3 B2 A
MUT E V IRT UAL
FPR
SBL SB SBR
FPL
VOL .
SL
SW
SR
STEREO
TUNED
Program Type
Item name
About 3 seconds after a display item is selected, its corresponding
information appears.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
PARTY
ZONE
3 B2 A
MUT E V IRT UAL
FPR
SBL SB SBR
FPL
VOL .
SL
SW
SR
STEREO
TUNED
CLASSICS
Information
Program Service
Program service name
Program Type
Current program type
Radio Text
Information on the current program
Clock Time
Current time
DSP Program
Sound mode name
Audio Decoder
Decoder name
Frequency
Frequency
Note
“Program Service”, “Program Type”, “Radio Text”, and “Clock Time” are not displayed if the radio
station does not provide the Radio Data System service.
n
Receiving traffic information automatically
When “TUNER” is selected as the input source, the unit automatically receives traffic
information. To enable this function, follow the procedure below to set the traffic
information station.
1
When “TUNER” is selected as the input source, press OPTION.
2
Use the cursor keys to select “Traffic Program” (TrafficProgram)
and press ENTER.
The traffic information station search will start in 5 seconds. Press ENTER
again to start the search immediately.
Note
To search upward/downward from the current frequency, press the cursor keys (q/w) while
“READY” is displayed.
To cancel the search, press RETURN.
Texts in parentheses denote indicators on the front display.
The following screen appears for about 3 seconds when the search
finishes.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
PARTY
ZONE
3 B2 A
MUT E V IRT UAL
FPR
SBL SB SBR
FPL
VOL .
SL
SW
SR
STEREO
TUNED
TP FM101.30MHz
Traffic information station (frequency)
Note
“TP Not Found” appears for about 3 seconds when no traffic information stations are found.
En
41
Playing back music stored on a Bluetooth® device
You can play back music files stored on a Bluetooth device (such as smartphones) on
the unit. Also, you can enjoy audio played back on the unit using Bluetooth speakers/
headphones.
Please also refer to the owner’s manual of your Bluetooth device.
Bluetooth device
(such as smartphones)
The unit
Bluetooth speakers/headphones
The unit
Note
The Bluetooth device must support A2DP.
To use the BLUETOOTH function, set “Bluetooth” (p.64) in the “Setup” menu to “On”.
You cannot make Bluetooth connections to a Bluetooth device (such as smartphones) and Bluetooth
speakers/headphones at the same time.
Connecting a Bluetooth® device (pairing)
When connecting a Bluetooth device to the unit for the first time, a pairing operation is
required. Pairing is an operation that registers the Bluetooth devices with each other
beforehand. Once pairing has been completed, subsequent reconnection will be easy
even after the Bluetooth connection is disconnected.
1
Press BLUETOOTH to select “Bluetooth” as the input source.
2
Hold down MEMORY on the front panel or the remote control for
more than 3 seconds.
“Searching…” appears on the front display.
Note
You can also use the “Option” menu to pair a Bluetooth device. Press OPTION, and then use the
cursor keys to select “Pairing
”.
If another Bluetooth device is already connected, disconnect the Bluetooth connection before
you perform a pairing operation.
To cancel pairing, press MEMORY.
3
Turn on the Bluetooth function on your device.
4
From the Bluetooth device list on your device, select “*******
Yamaha” (*******: model name of the unit).
After pairing has been completed and the unit is connected to the
Bluetooth device, “
Connected” appears on the front display. While a
Bluetooth connection is established, the Bluetooth indicators light up.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
PARTY
ZONE
3 B2 A
MUT E V IRT UAL
SBL SB SBR
FPRFPL
STEREO
TUNED
VOL .
SL
SW
SR
Connected
Note
If you are prompted to input a passkey during a pairing procedure, input the numerals “0000”.
Complete a pairing procedure within 30 seconds.
If no Bluetooth devices are found, “Not found” appears.
En
42
Playback of Bluetooth® device contents
Connect a paired Bluetooth device and start playback. Check the following
beforehand:
Pairing has been completed.
Bluetooth function on the Bluetooth device is turned on.
1
Operate the Bluetooth device to establish a Bluetooth connection.
Select the model name of the unit from the Bluetooth device list on your
device.
When a connection is established, the unit’s input source automatically
switches to “
Bluetooth”.
Note
If you do not want the input source to switch automatically when a connection is established, set
“Input Interlock” (
p.47) to “Off” in the “Option” menu.
You can operate the unit to search and connect the Bluetooth device (only the most recently
connected device). In that case, follow one of the procedures below.
Switch the input source to “Bluetooth”.
Press ENTER while the input source is “Bluetooth”. Otherwise, press OPTION and use the
cursor keys to select “Connect”.
If you cannot connect the device, please perform pairing again.
2
Operate the Bluetooth device to play back music.
Note
You cannot operate the unit to select or play back music, or display informations such as song
names.
Follow one of the procedures below to disconnect a Bluetooth connection.
Perform the disconnect operation on the Bluetooth device.
Press ENTER.
Press OPTION and use the cursor keys to select “Disconnect”.
Switch the unit's input source to other than “Bluetooth”.
Press the SETUP key, then use the cursor keys to select "Bluetooth", then "Disconnect".
Enjoying audio using Bluetooth® speakers/
headphones
Follow the procedure below to establish a Bluetooth connection between Bluetooth
speakers/headphones and the unit.
1
Use the input selection keys on the remote control to select an
input source.
Select an input source other than Bluetooth.
2
Press SETUP.
3
Use the cursor keys to select “Bluetooth” and press ENTER.
4
Use the cursor keys to set “Bluetooth” to “On”, and then set
Transmitter” to “On” in the same way.
5
Use the cursor keys to select “Device Search” to search the
Bluetooth devices.
The list of Bluetooth devices is displayed.
6
Select the Bluetooth speakers/headphones to be connected with
the unit and press ENTER.
When the connection process finishes, audio played back on the unit will
be reproduced from the Bluetooth speakers/headphones.
Note
If the desired Bluetooth device is not displayed on the list, set the Bluetooth device to the pairing
mode and then select “
Device Search”.
Follow one of the procedures below to terminate the Bluetooth connection.
Perform the disconnect operation on the Bluetooth speakers/headphones.
Press the SETUP key, then use the cursor keys to select "Bluetooth", then "Transmitter", and
then "Off".
En
43
Playing back music stored on a USB storage device
You can play back music files stored on a USB storage device on the unit.
Note
For details on playable USB devices, see “Supported devices and file formats” (p.79).
Connecting a USB storage device
1
Connect the USB storage device to the USB jack.
AUX
STRAIGHT
RADIO
AUDIO
USB
The unit (front)
USB storage device
Note
If the USB storage device contains many files, it may take time to load them. In this case, “Loading…”
appears in the front display.
Stop playback of the USB storage device before disconnect it from the USB jack.
Connect a USB storage device directly to the USB jack of the unit. Do not use extension cables.
The unit cannot charge USB devices while it is in standby mode.
Playback of USB storage device contents
Follow the procedure below to operate the USB storage device contents and start
playback.
You can control the USB memory device with the menu displayed on the TV screen.
Note
Operations with TV screen are available only when your TV is connected to the unit via HDMI.
“_” (underscore) will be displayed for characters not supported by the unit.
1
Press USB to select “USB” as the input source.
The browse screen (p.45) is displayed on the TV.
Note
If playback is ongoing on your USB storage device, the playback screen is displayed.
2
Use the cursor keys to select an item and press ENTER.
If a song is selected, playback starts and the playback screen (p.45) is
displayed.
Note
To return to the previous screen, press RETURN.
To switch the screen mode browse/playback/off, press DISPLAY.
Files not supported by the unit cannot be selected.
En
44
n
Browse screen
1 4
2
5
3
1
List name
2
Contents list
Displays the list of USB storage device contents. Use the cursor keys to select an
item and press ENTER to confirm the selection.
3
Item number/total
4
Status indicators
Display the current repeat/random settings (p.46) and playback status (such as
play/pause).
5
Operation menu
Press the cursor key (r) and then use the cursor keys (q/w) to select an item.
Press ENTER to confirm the selection.
Icon Function
Moves 10 pages backward.
Moves to the previous page of the list.
Moves to the next page of the list.
Moves 10 pages forward.
Moves to the playback screen.
Note
A content selected by the cursor is displayed on the front display.
n
Playback screen
2
1
1
Status indicators
Display the current repeat/random settings (p.46) and playback status (such as
play/pause).
2
Playback information
Displays the artist name, album name, song title, and elapsed time.
En
45
Use the following remote control keys to control playback.
TUNING
PRESET
MUTE
TUNING
MEMORY
TOP MENU
HOME
POP-UP/MENU
DISPLAYRETURN
SETUP
OPTION
ENTER
FM/AM
VOLUME
PROGR AM
USB
STRAIGHT
ENHANCER BASS
BLUETOOTH
INPU T
BD
DVD
TV
CD
SC ENE
RADIO
SLEEP
BLUE
YELLOWGREEN
RED
TUNING
PRESET
TUNING
MEMORY
BLUE
YELLOWGREEN
RED
PRESET
BLUE
YEL
LO
W
LO
LO
GREEN
RE
D
External device operation
keys
External device
operation keys
Function
a
Resumes playback from pause or starts playback of the previously
selected song.
s
Stops playback.
d
Stops playback temporarily.
f
Skips forward/backward.
g
h
Searches forward/backward (by holding down).
j
Note
A content name of a current playback is displayed on the front display. To switch the displayed item, press
INFO
(p.30).
n
Repeat/random settings
You can configure the repeat/random settings for playback of USB storage device
contents.
1
When “USB” is selected as the input source, press OPTION.
2
Use the cursor keys to select “Repeat” (Repeat) and press
ENTER.
Note
To return to the previous screen during menu operations, press RETURN.
Texts in parentheses denote indicators on the front display.
3
Use the cursor keys (e/r) to select a setting.
Setting Function
Off (Off) Turns off the repeat function.
One (One)
Plays back the current song repeatedly. “c” appears
on the TV screen.
All (All)
Plays back all songs in the current album (folder)
repeatedly.
v” appears on the TV screen.
Random (Random)
Plays back songs in random order.
x” appears on the TV screen.
4
To exit from the menu, press OPTION.
En
46
Configuring playback settings for different playback sources (Option menu)
You can configure separate playback settings for different playback sources. This
menu is available on the front panel (or on the TV screen), allowing you to easily
configure settings during playback.
1
Press OPTION.
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
PARTY
ZONE
3 B2 A
MUT E V IRT UAL
FPR
SBL SB SBR
FPL
STEREO
TUNED
VOL .
SL
SW
SR
Input Select
Front display
TV screen
2
Use the cursor keys to select an item and press ENTER.
Note
To return to the previous screen during menu operations, press RETURN.
3
Use the cursor keys (e/r) to select a setting.
4
To exit from the menu, press OPTION.
Option menu items
Note
Available items vary depending on the selected input source.
Text in parentheses denotes indicators on the front display.
Default settings are underlined.
Item Function Page
Input Select (Input Select)
Switches the input source. p.48
Tone Control (
Tone Control)
Adjusts the level of high-frequency range and low-
frequency range individually.
p.48
DSP/Surround
(DSP/
Surround)
Program (PRG)
Select the sound programs and stereo playback. p.33
Sur.Decode
(SrDec)
Select which surround decoder is used when
Sur.Decode
is selected as the program.
p.35
DSP Level
(DSP Level)
Adjusts the sound field effect level. p.48
Adaptive DRC
(A.DRC)
Sets whether the dynamic range (from maximum to
minimum) is automatically adjusted when the volume
is adjusted.
p.48
Enhancer
(Enhancer)
Enables/disables Compressed Music Enhancer. p.48
Volume Trim
(Volume Trim)
Input Trim
(In.Trim)
Corrects volume differences between input sources. p.49
Subwoofer Trim
(SW.Trim)
Fine-adjusts the subwoofer volume. p.49
Lipsync (Lipsync)
Enables/disables the “Lipsync” setting in the “Setup”
menu.
p.49
Signal Info. (Signal Info.)
Displays information about the video/audio signal. p.49
Audio In (Audio In)
Combines the video jack of the selected input source
with an audio jack of others.
p.49
Video Out (Video Out)
Selects a video to be output with the selected audio
source.
p.50
FM Mode (FM Mode)
Switches between “Stereo” and “Mono” for FM radio
reception.
p.37
Preset (Preset)
Auto Preset
Automatically registers FM radio stations with strong
signals as presets.
p.38
Clear Preset
Clear radio stations registered to preset numbers. p.40
Traffic Program
(TrafficProgram)
(U.K. and Europe models only)
Automatically searches for a traffic information
station.
p.41
En
47
Item Function Page
Repeat
(Repeat)
Configures the repeat setting for the USB storage
device.
p.46
Pairing
(Pairing)
Performs a pairing operation between the unit and
your Bluetooth device.
p.42
Connect/Disconnect (Connect/
Disconnect)
Connects/disconnects the Bluetooth device. p.42
Input Interlock (Interlock)
Sets whether the input source automatically switches
to "Bluetooth" when a Bluetooth connection is
established.
p.43
n
Input Select (Input Select)
Switches the input source. Press ENTER to switch to the selected input source.
n
Tone Control (Tone Control)
Adjusts the level of high-frequency range (Treble) and low-frequency range (Bass)
individually.
Choices
Treble (Treble), Bass (Bass)
Setting range
-6.0 dB to 0.0 dB to +6.0 dB (0.5 dB increments)
Note
When both “Treble” and “Bass” are 0.0 dB, “Bypass” appears.
You can also adjust the tone with the front panel controls. Press TONE CONTROL to select “Treble” or
“Bass”, then press PROGRAM to make an adjustment.
If you set an extreme value, sounds may not match those from other channels.
n
DSP/Surround (DSP/Surround)
Configures the sound field program and surround settings.
DSP Level (DSP Level)
Adjusts the sound field effect level.
Setting range
-6 dB to
0 dB to +3 dB (1 dB increments)
Adaptive DRC (A.DRC)
Sets whether the dynamic range (from maximum to minimum) is automatically
adjusted when the volume level is adjusted. When it is set to “On”, it is useful for
listening to playback at a low volume at night.
Settings
On (On) Automatically adjusts the dynamic range.
Off (Off) The dynamic range is not automatically adjusted.
If “On” is selected, the dynamic range becomes narrow at a low volume and wide
at a high volume.
Enhancer (Enhancer)
Enables/disables Compressed Music Enhancer (p.36).
Note
This setting is applied separately to each input source.
You can also use ENHANCER on the remote control to enable/disable Compressed Music Enhancer
(p.36).
Settings
Off (Off) Disables Compressed Music Enhancer.
On (On) Enables Compressed Music Enhancer.
Default
Bluetooth, USB, TUNER: On (On)
Others: Off (Off)
En
48
n
Volume Trim (Volume Trim)
Fine-adjusts volume difference between input sources or subwoofer volume.
Input Trim (In.Trim)
Corrects volume differences between input sources. If you are bothered by volume
differences when switching between input sources, use this function to correct it.
Note
This setting is applied separately to each input source.
Setting range
-6.0 dB to
0.0 dB to +6.0 dB (0.5 dB increments)
Subwoofer Trim (SW.Trim)
Fine-adjusts the subwoofer volume.
Setting range
-6.0 dB to
0.0 dB to +6.0 dB (0.5 dB increments)
n
Lipsync (Lipsync)
Enables/disables the adjustment configured in “Lipsync” (p.59) in the “Setup” menu.
Note
This setting is applied separately to each input source.
Settings
Off (Off) Disables the “Lipsync” adjustment.
On (On) Enables the “Lipsync” adjustment.
n
Signal Info. (Signal Info.)
Displays information about the video/audio signal.
Choices
Format (FORMAT) Audio format of the input signal
Channel (CHANNEL)
The number of source channels in the input signal (front/surround/LFE)
For example, “3/2/0.1” means 3 front channels, 2 surround channels, and
LFE.
Sampling (SAMPLING) The number of samples per second of the input digital signal
Video In (VIDEO IN) Type and resolution of the input digital signal
Video Out
(VIDEO OUT
)
Type and resolution of the output digital signal
Note
To switch the information on the front display, press the cursor keys (q/w) repeatedly.
n
Audio In (Audio In)
Combines the video jack of the selected input source with an audio jack of others. For
example, use this function in the following cases.
Connecting a playback device that supports HDMI video output, but not HDMI
audio output
Input sources
HDMI 1-4, AV 1-3
Settigns
AV 1-3, AUDIO 1-2
Setup procedure
See “Changing the combination of video/audio input jacks” (p.21).
En
49
n
Video Out (Video Out)
Selects a video to be output with the selected audio source. For example, you can
watch the video while listening to the radio.
Input sources
AUDIO, TUNER, USB, Bluetooth, AUX
Settings
Off (Off) Does not output video.
HDMI 1-4, AV 1-3 Outputs video input through the corresponding video input jacks.
En
50
CONFIGURATIONS
Configuring various functions (Setup Menu)
You can configure the unit’s various function with the menu displayed on the TV
screen.
Note
Operations with TV screen are available only when your TV is connected to the unit via HDMI. If not, carry out
operations while viewing the front display.
1
Press SETUP.
2
Use the cursor keys to select a menu and press ENTER.
3
Use the cursor keys to select an item and press ENTER.
Note
To return to the previous screen during menu operations, press RETURN.
4
Use the cursor keys (e/r) to select a setting and press ENTER.
5
To exit from the menu, press SETUP.
En
51
Setup menu items
Menu Item Function Page
Speaker
Configuration
Subwoofer
Selects whether or not a subwoofer is connected. p.54
Front
Selects the size of the front speakers. p.54
Center
Selects whether or not a center speaker is connected and its size. p.54
Surround
Selects whether or not surround speakers are connected and their size. p.55
Crossover
Sets the lower limit of the low-frequency component that can be output from speakers whose size is set to “Small”. p.55
Subwoofer Phase
Sets the phase of the subwoofer. p.55
Extra Bass
Enables/disables Extra Bass. p.55
Virtual CINEMA FRONT
Selects whether to use the front 5-channel speaker (Virtual CINEMA FRONT) configuration. p.55
Distance
Sets the distance between each speaker and listening position. p.55
Level
Adjusts the volume of each speaker. p.56
Equalizer
Adjusts the tone with an equalizer. p.56
Test Tone
Enables/disables the test tone output. p.56
HDMI
HDMI Control
Enables/disables HDMI Control. p.57
Audio Output
Enables/disables the audio output from a TV. p.57
4K Upscaling
Enables/disables the upscaling function. p.57
TV Audio Input
Selects an audio input jack of the unit to be used for TV audio input. p.57
Standby Sync
Selects whether to use HDMI control to link the standby behavior of the TV and the unit. p.58
ARC
Enables/disables ARC. p.58
SCENE
Enables/disables SCENE link playback. p.58
Sound
DSP Parameter
Panorama
Enables/disables the broadening effect of the front sound field. p.59
Center Width
Adjusts the broadening effect of the center sound field. p.59
Dimension
Adjusts the difference in level between the front and surround sound fields. p.59
Center Image
Adjusts the center localization (broadening effect) of the front sound field. p.59
Lipsync
Select
Selects the method to adjust the delay between video and audio output. p.59
Adjustment
Adjusts the delay between video and audio output manually. p.60
Dialogue Dialogue Level
Adjusts the volume of dialogue sounds. p.60
Volume
Scale
Switches the scale of the volume display. p.60
Dynamic Range
Selects the dynamic range adjustment method for bitstream audio (Dolby Digital and DTS signals) playback. p.60
Max Volume
Sets the limit value of the volume. p.60
Initial Volume
Sets the initial volume for when this receiver is turned on. p.60
En
52
Menu Item Function Page
ECO
Auto Power Standby
Set the amount of time for the auto-standby function. p.61
ECO Mode
Enables/disables the eco mode (power saving mode). p.61
Function
Input Rename
Changes the input source name displayed on the front display. p.62
Input Skip
Set which input source is skipped when operating the INPUT key. p.63
Dimmer
Adjusts the brightness of the front display. p.63
Memory Guard
Prevents accidental changes to the settings. p.63
Remote Color Key
Set the unit's functions for the RED/GREEN/YELLOW/BLUE key of the remote control. p.64
Bluetooth
Bluetooth
Enables/disables the Bluetooth functions. p.64
Audio Receive
Disconnect
Terminates the Bluetooth connection between the Bluetooth device (such as smartphones) and the unit. p.42
Bluetooth Standby
Selects whether to enable/disable the function that turns on the unit from Bluetooth devices (Bluetooth standby). p.64
Audio Send
Transmitter
Enables/disables the Bluetooth audio transmitter function. p.65
Device Search
Searches available Bluetooth devices (speakers/headphones) when the unit is used as a Bluetooth audio transmitter. p.43
Language
Select an on-screen menu language. p.65
En
53
Speaker
Configures the speaker settings manually.
Note
Default settings are underlined.
n
Configuration
Configures the output characteristics of the speakers.
Note
When configuring the speaker size, as a general guideline, select “Large” if the woofer diameter of your
speaker is 16 cm (61/4”) or larger, or “Small
” if it is smaller than 16 cm (61/4”).
Subwoofer
Selects whether or not a subwoofer is connected.
Settings
Use
Select this option when a subwoofer is connected.
The subwoofer will produce LFE (low-frequency effect) channel audio
and low-frequency components from other channels.
None
Select this option when no subwoofer is connected.
The front speakers will produce LFE (low-frequency effect) channel
audio and low-frequency components from other channels.
Front
Selects the size of the front speakers.
Settings
Small
Select this option for small speakers.
The subwoofer will produce front channel low-frequency components
(configurable in “
Crossover”).
Large
Select this option for large speakers.
The front speakers will produce all of the front channel frequency
components.
Note
“Front” is automatically set to “Large” when “Subwoofer” is set to “None”.
Center
Selects whether or not a center speaker is connected and its size.
Settings
Small
Select this option for small speakers.
The subwoofer or front speakers will produce center channel low-
frequency components (configurable in “
Crossover”).
Large
Select this option for large speakers.
The center speaker will produce all of the center channel frequency
components.
None
Select this option when no center speaker is connected.
The front speakers will produce center channel audio.
En
54
Surround
Selects whether or not surround speakers are connected and their sizes.
Settings
Small
Select this option for small speakers.
The subwoofer or front speakers will produce surround channel low-
frequency components (configurable in “
Crossover”).
Large
Select this option for large speakers.
The surround speakers will produce all of the surround channel
frequency components.
None
Select this option when no surround speakers are connected.
The front speakers will produce surround channel audio. Virtual
CINEMA DSP works when you select a sound program.
Crossover
Sets the lower limit of the low-frequency components that can be output from a
speaker whose size is set to “
Small”. A frequency sound lower than the specified
value will be produced from the subwoofer or front speakers.
Settings
40 Hz, 60 Hz,
80 Hz, 90 Hz, 100 Hz, 110 Hz, 120 Hz, 160 Hz, 200 Hz
Note
If the volume and crossover frequency are adjustable on your subwoofer, set the volume to half and
crossover frequency to maximum.
Subwoofer Phase
Sets the phase of the subwoofer. When the bass sound is lacking or unclear,
switch the subwoofer phase.
Settings
Normal Does not reverse the subwoofer phase.
Reverse Reverses the subwoofer phase.
Extra Bass
Enables/disables Extra Bass. When Extra Bass is enabled, you can enjoy
enhanced bass sounds, regardless of the size of the front speakers and the
presence or absence of the subwoofer.
Settings
Off Disables Extra Bass.
On Enables Extra Bass.
Note
You can also use BASS on the remote control to enable/disable Extra Bass (p.36).
Virtual CINEMA FRONT
Selects whether to use the front 5-channel speaker (Virtual CINEMA FRONT)
configuration.
Settings
Off Disables the front 5-channel speaker configuration.
On Enables the front 5-channel speaker configuration.
Note
Select “On” only when utilizing the Virtual CINEMA FRONT configuration (p.13).
This setting is not available when “Surround” is set to “None”.
n
Distance
Sets the distance between each speaker and listening position so that sounds from the
speakers reach the listening position at the same time. First, select the unit of distance
from “Meter” or “Feet”.
Choices
Front L, Front R, Center, Surround L, Surround R, Subwoofer
Setting range
0.30 m to 24.00 m (1.0 ft to 80.0 ft), 0.05 m (0.2 ft) increments
Default
Front L, Front R, Subwoofer: 3.00 m (10.0 ft)
Center: 2.60 m (8.6 ft)
Others: 2.40 m (8.0 ft)
En
55
n
Level
Adjusts the volume of each speaker.
Choices
Front L, Front R, Center, Surround L, Surround R, Subwoofer
Setting range
-10.0 dB to +10.0 dB (0.5 dB increments)
Default
Front L, Front R, Subwoofer: 0.0 dB
Others: -1.0 dB
n
Equalizer
Adjusts the tone with an equalizer.
EQ Select
Selects the type of equalizer to be used.
Settings
PEQ
Applies the parametric equalizer values obtained by the YPAO
measurement (
p.25).
GEQ
Select this option when you want to adjust the equalizer manually.
For details, see “Manual equalizer adjustment”.
Off Does not use the equalizer.
Note
“PEQ” is available only when the YPAO has been performed (p.25).
n
Manual equalizer adjustment
1
Set “EQ Select” to “GEQ”.
2
Use the cursor keys (q/w) to select “Channel” and the cursor
keys (e/r) to select the desired speaker channel.
3
Use the cursor keys (q/w) to select the desired band
(frequency) and the cursor keys (e/r) to adjust the gain.
Setting range
-6.0 dB to +6.0 dB
4
To exit from the menu, press SETUP.
n
Test Tone
Enables/disables the test tone output. Test tone output helps you to adjust the speaker
balance or equalizer while confirming its effect.
Settings
Off Does not output test tones.
On
Outputs test tones automatically when you adjust the speaker balance or
equalizer.
En
56
HDMI
Configures the HDMI settings.
Note
Default settings are underlined.
n
HDMI Control
Enables/disables HDMI Control (p.80).
Settings
Off Disables HDMI Control.
On
Enables HDMI Control.
Configure the settings in “TV Audio Input”, “Standby Sync”, “ARC”, and
“SCENE”.
Note
To use HDMI control, you need to perform the HDMI Control link setup (p.80) after connecting HDMI
Control-compatible devices.
n
Audio Output
Enables/disables the audio output from a TV connected to the HDMI OUT jack.
Settings
Off Disables the audio output from the TV.
On Enables the audio output from the TV.
Note
This setting is available only when “HDMI Control” is set to “Off”.
n
4K Upscaling
Enables/disables the upscaling function. When it is enabled, 1080p content is
displayed at 4K resolution.
Settings
Off Disables the upscaling function.
On Enables the upscaling function.
n
TV Audio Input
Selects an audio input jack of the unit to be used for TV audio input when “HDMI
Control” is set to “On”. The unit’s input source automatically switches to TV audio when
the TV input is switched to its built-in tuner.
Settings
AV 1–3, AUDIO 1–2
Default
AV 2
Note
When using ARC to input TV audio to the unit, you cannot use the input jacks selected here for connecting an
external device because the input will be used for TV audio input.
En
57
n
Standby Sync
Select whether to use HDMI control to link the unit's standby mode to the TV's power
when “HDMI Control
” is set to “On”.
Settings
Off Does not set the unit to standby mode when the TV is turned off.
On Sets the unit to standby mode when the TV is turned off.
Auto
Sets the unit to standby mode when the TV is turned off only when the unit
is receiving TV audio or HDMI signals.
n
ARC
Enables/disables ARC (p.19) when “HDMI Control” is set to “On”.
Settings
Off Disables ARC.
On Enables ARC.
Note
You do not need to change this setting normally. In case noises are produced from the speakers connected
to the unit because TV audio signals input to the unit via ARC are not supported by the unit, set “ARC” to “Off”
and use the TV’s speakers.
n
SCENE
Enables/disable SCENE link playback when “HDMI Control” is set to “On”.
When SCENE link playback is enabled, HDMI Control-compatible devices connected
to the unit via HDMI automatically works as follows, with a scene selection.
TV: turning on and displaying video from the playback device
Playback device: starting playback
Choices (SCENE keys)
BD / DVD, TV, CD, RADIO
Settings
Off Disables SCENE link playback for the selected SCENE key.
On Enables SCENE link playback for the selected SCENE key.
Default
BD / DVD, TV: On
CD, RADIO: Off
Note
SCENE link playback may not work properly due to the compatibility between devices. We recommend using
TV and playback devices from the same manufacturer so that HDMI Control works more effectively.
En
58
Sound
Configures the audio output settings.
Note
Default settings are underlined.
n
DSP Parameter
Configures the surround decoder settings.
Panorama
Enables/disables the broadening effect of the front sound field. When this function
is enabled, you can wrap front left/right channel sounds around the sound field
and generate a spacious sound field in combination with the surround sound field.
This setting is effective when “
DPL Music” is selected.
Settings
Off Disables the broadening effect of the front sound field.
On Enables the broadening effect of the front sound field.
Center Width
Adjusts the broadening effect of the center sound field. Higher to enhance the
broadening effect, and lower to reduce it (closer to center). This setting is effective
when “DPL Music” is selected.
Setting range
0 to 3 to 7
Dimension
Adjusts the difference in level between the front and surround sound fields. Higher
to strengthen the front sound field and lower to strengthen the surround sound
field. This setting is effective when “
DPL Music” is selected.
Setting range
-3 to
0 to +3
Center Image
Adjusts the center localization (broadening effect) of the front sound field. Adjust
this higher to strengthen the center localization (less broadening effect) or lower to
weaken it (more broadening effect). This setting is effective when “
Neo:6 Music” is
selected.
Setting range
0.0 to
0.3 to 1.0
n
Lipsync
Adjusts the delay between video and audio output.
Note
You can enable/disable the Lipsync function by input sources in “Lipsync (Lipsync)” (p.49) in the “Option”
menu.
Select
Selects the method to adjust the delay between video and audio output.
Setting range
Manual
Select this option when you want to adjust the delay between video
and audio output manually.
Adjust the audio output timing in “Adjustment”.
Auto
Adjusts the delay between video and audio output automatically when
a TV that supports an automatic lipsync function is connected to the
unit via HDMI.
If necessary, you can fine-adjust the audio output timing in
“Adjustment”.
Note
“Select” is automatically set to “Manual” depending on the TV connected to the unit.
En
59
Adjustment
Adjusts the delay between video and audio output manually when “Select” is set to
“Manual
”. You can fine-adjust the audio output timing when “Select” is set to
“Auto”.
Setting range
0 ms to 500 ms (1 ms increments)
n
Dialogue
Adjusts the volume of dialogue sounds.
Dialogue Level
Adjusts the volume of the center orientation sounds such as dialogue.
Setting range
0 to 3 (higher to strengthen)
n
Volume
Configures the volume settings.
Scale
Switches the scale of the volume display.
Settings
dB Displays the volume in the “dB” unit.
0-97 Displays the volume in the numeric value (0.5 to 97.0).
Dynamic Range
Selects the dynamic range adjustment method for bitstream audio (Dolby Digital
and DTS signals) playback.
Settings
Maximum Produces audio without adjusting the dynamic range.
Standard Optimizes the dynamic range for regular home use.
Min/Auto
Sets the dynamic range for clear sound even at night or at low
volumes.
When playing back Dolby TrueHD signals, the dynamic range is
automatically adjusted based on the input signal information.
Max Volume
Sets the limit value of the volume.
Setting range
-30.0 dB to +15.0 dB (5.0 dB increments),
+16.5 dB [50.0 to 95.0 (5.0 increments),
97.0]
Initial Volume
Sets the initial volume when the receiver is turned on.
Settings
Off
Sets the level to the volume level of the unit when it last entered
standby mode.
Mute Sets the unit to mute the audio output.
-80.0 dB to +16.5 dB
(0.5 dB increments)
[0.5 to 97.0
(0.5 increments)]
Sets the level to the specified volume level.
En
60
ECO
Configures the power supply settings.
Note
Default settings are underlined.
n
Auto Power Standby
Set the amount of time for the auto-standby function.
Settings
Off Does not set the unit to standby mode automatically.
20 minutes
Sets the unit to standby mode when you have not operated the unit and
the unit has not detected any input signal for the specified time.
2 hours, 4 hours,
8 hours, 12 hours
Sets the unit to standby mode when you have not operated the unit for the
specified time.
Default
U.K. and Europe models: 20 minutes
Other models: Off
Note
Just before the unit enters standby mode, “AutoPowerStdby” appears and then countdown starts in the front
display.
n
ECO Mode
You can reduce the unit’s power consumption by setting the eco mode to “On”. After
setting, be sure to press ENTER to restart the unit.
When the eco mode is enabled, you can reduce the unit’s power consumption.
Settings
Off Disables the eco mode.
On Enables the eco mode.
Note
When “ECO Mode” is set to “On”, the front panel display may become dark.
If you want to play audio at high volume, set “ECO Mode” to “Off”.
En
61
Function
Configures the functions that make the unit easier to use.
Note
Default settings are underlined.
n
Input Rename
Changes the input source name displayed on the front display. You can also select a
name created by the Auto Rename function.
Input sources
HDMI 1-4, AUDIO 1-2, AV 1-3, USB, Bluetooth, AUX
Default
HDMI 1-4: Auto
Others: Manual (For USB, Bluetooth, AUX only “Manual” can be selected.)
Procedure to rename automatically
1
Use the cursor keys (q/w) to select an input source to be
renamed.
2
Use the cursor keys (e/r) to select “Auto”.
The unit creates a name automatically according to the connected
device.
3
To change another input source, repeat steps 1 to 2.
4
To exit from the menu, press SETUP.
Note
During selecting “Auto”, the created name is saved even after the device connection is terminated. To
reset to the default setting, switch the setting to “Manual
” at once and then set it again to “Auto”.
Procedure to rename manually
1
Use the cursor keys (q/w) to select an input source to be
renamed.
2
Use the cursor keys (e/r) to select “Manual” and press
ENTER.
The edit screen is displayed.
3
Use the cursor keys and ENTER key to edit the name, and then
select “OK” and press ENTER.
Note
To cancel the entry, select “CANCEL”.
If you select "RESET", the default input name will be inserted into the editing area.
4
To change another input source name, repeat steps 1 to 4.
5
To exit from the menu, press SETUP.
En
62
n
Input Skip
Set which input source is skipped when operating the INPUT key.
You can select the desired input source quickly by using this function.
Input sources
HDMI 1-4, AUDIO 1-2, AV 1-3, TUNER, USB, Bluetooth, AUX
Settings
Off Does not skip the selected input source.
On Skips the selected input source.
n
Dimmer
Adjusts the brightness of the front display.
Setting range
-4 to
0 (higher to brighten)
Note
The front display may become dark when “ECO Mode” (p.61) is set to “On”.
n
Memory Guard
Prevents accidental changes to the settings.
Settings
Off Does not protect the settings.
On Protects the settings until “Off” is selected.
Note
When “Memory Guard” is set to “On”, the lock icon (o) is displayed on the menu screen.
En
63
n
Remote Color Key
Set the unit's functions for the RED/GREEN/YELLOW/BLUE key of the remote control.
Settings
Default
Assigns the functions of playback devices connected to the unit with an
HDMI cable.
Input
Assigns the unit's input sources to each key. The assigned input sources
can be set separately.
Input sources
HDMI 1-4, AUDIO 1-2, AV 1-3, TUNER, USB, Bluetooth, AUX
Default
RED: HDMI2, GREEN: HDMI4, YELLOW: AV 2, BLUE: AUX
Program
Assigns the functions of sound mode to each key.
RED: MOVIE
GREEN: MUSIC
YELLOW: STEREO
BLUE: SUR.DECODE
For example, if you press the RED key repeatedly, you can select your
favorite sound program from the sound programs (MOVIE
) (p.33) suitable
for the video source.
Bluetooth
Configures the Bluetooth settings.
n
Bluetooth
Enables/disables the Bluetooth function (p.42).
Settings
Off Disables the Bluetooth function.
On Enables the Bluetooth function.
n
Audio Receive
Configures the Bluetooth settings when the unit is used as the Bluetooth audio
receiver.
Bluetooth Standby
Selects whether to enable/disable the function that turns on the unit from Bluetooth
devices (Bluetooth standby). If this function is set to “On”, the unit automatically
turns on when a connect operation is performed on the Bluetooth device.
Settings
Off Disables the Bluetooth standby function.
On
Enables the Bluetooth standby function.
(The unit consumes more power than when “
Off” is selected.)
En
64
n
Audio Send
Configures the Bluetooth settings when the unit is used as the Bluetooth audio
transmitter.
Transmitter
Enables/disables the Bluetooth audio transmitter function.
When this function is enabled, you can enjoy audio played back on the unit using
Bluetooth speakers/headphones (
p.43).
Settings
Off Disables the Bluetooth audio transmitter function.
On Enables the Bluetooth audio transmitter function.
Language
Select an on-screen menu language.
Note
Default settings are underlined.
Settings
English English
日本語 Japanese
Français French
Deutsch German
Español Spanish
Русский Russian
Italiano Italian
中文 Chinese
Note
The information on the front display is provided in English only.
En
65
Configuring the system settings (ADVANCED SETUP menu)
Configure the system settings of the unit while viewing the front display.
1
Set the unit to standby mode.
2
While holding down STRAIGHT on the front panel, press
z (power).
(power)
z
STRAIGHTPROGRAM
3
Press PROGRAM to select an item.
4
Press STRAIGHT to select a setting.
5
Press z (power) to set the unit to standby mode and turn it on
again.
The new settings take effect.
ADVANCED SETUP menu items
Note
Default settings are underlined.
Item Function Page
SP IMP.
(U.S.A. and Canada models only)
Changes the speaker impedance setting.
p.66
REMOTE ID Selects the unit’s remote control ID. p.67
TU
(Asia, Taiwan and General models only)
Changes the FM/AM tuning frequency setting.
p.67
TV FORMAT Switches the video signal type of HDMI output. p.67
4K MODE Selects the HDMI 4K signal format. p.68
INIT Restores the default settings. p.68
UPDATE Updates the firmware. p.68
VERSION Checks the version of firmware currently installed on the unit. p.68
Changing the speaker impedance setting (SP IMP.)
(U.S.A. and Canada models only)
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
VOL .
FPR
SL
SW
SR
SBL SB SBR
FPL
MUT E V IRT UAL
SP IMP.8¬MIN
Change the unit’s speaker impedance settings depending on the impedance of the
speakers connected.
Settings
6 Ω MIN Select this option when you connect 6-ohm speakers to the unit.
8 Ω MIN Select this option when you connect 8-ohm or higher speakers to the unit.
En
66
Selecting the remote control ID (REMOTE ID)
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
VOL .
FPR
SL
SW
SR
SBL SB SBR
FPL
MUT E V IRT UAL
REMOTE ID•ID1
Change the unit’s remote control ID so that it matches the remote control’s ID (default:
ID1). When using multiple Yamaha AV receivers, you can set each remote control with
a unique remote control ID for its corresponding receiver.
Settings
ID1, ID2
n
Changing the remote control ID of the remote control
1
To select ID1, while holding down the cursor key (e), hold down
SCENE (BD/DVD) for more than 3 seconds.
To select ID2, while holding down the cursor key (e), hold down
SCENE (TV) for more than 3 seconds.
Changing the FM/AM tuning frequency setting (TU)
(Asia, Taiwan and General models only)
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
VOL .
FPR
SL
SW
SR
SBL SB SBR
FPL
MUT E V IRT UAL
TU••FM50/AM9
Change the FM/AM tuning frequency setting of the unit depending on your country or
region.
Settings
FM100/AM10
Select this when you want to adjust the FM frequency by 100-kHz steps
and AM by 10-kHz steps.
FM50/AM9
Select this when you want to adjust the FM frequency by 50-kHz steps
and AM by 9-kHz steps.
Switching the video signal type (TV FORMAT)
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
VOL .
FPR
SL
SW
SR
SBL SB SBR
FPL
MUT E V IRT UAL
TV FORMATNTSC
Switch the video signal type of HDMI output so that it matches to the format of your TV.
Since the unit automatically selects the video signal type so that it matches to the TV, it
is unnecessary to change the setting normally. Change the setting only when images
on the TV screen do not appear correctly.
Settings
NTSC, PAL
Default
U.S.A., Canada, Korea, Taiwan and General models: NTSC
Other models: PAL
En
67
Selecting the HDMI 4K signal format (4K MODE)
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
VOL .
FPR
SL
SW
SR
SBL SB SBR
FPL
MUT E V IRT UAL
4K MODEMODE 1
Selects the format of signals input/output at the unit when HDMI 4K compatible TV and
playback device are connected to the unit.
Settings
MODE 1
Inputs/outputs 4K signals shown in the table below. Depending on the
connected device or HDMI cables, video may not be displayed correctly.
In this case, select “MODE 2”.
MODE 2 Inputs/outputs 4K signals shown in the table below.
Note
When “MODE 1” is selected, use a Premium High Speed HDMI Cable or Premium High Speed Cable with
Ethernet.
Format
MODE 1 MODE 2
8 bit 10 bit 12 bit 8 bit 10 bit 12 bit
4K/60, 50 Hz
RGB 4:4:4
4
YCbCr 4:4:4
4
YCbCr 4:2:2
4
YCbCr 4:2:0
4 4
4K/30, 25, 24 Hz
RGB 4:4:4
4 4
YCbCr 4:4:4
4 4
YCbCr 4:2:2
4 4
Restoring the default settings (INIT)
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
VOL .
FPR
SL
SW
SR
SBL SB SBR
FPL
MUT E V IRT UAL
INITCANCEL
Restores the default settings for the unit.
Choices
ALL Restores the default settings for the unit.
CANCEL Does not perform an initialization.
Updating the firmware (UPDATE)
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
VOL .
FPR
SL
SW
SR
SBL SB SBR
FPL
MUT E V IRT UAL
UPDATE•USB
New firmware that provides additional features or product improvements will be
released as needed. Updates can be downloaded from our website. For details, refer
to the information supplied with updates.
n
Firmware update procedure
Do not perform this procedure unless firmware update is necessary. Also, make sure
you read the information supplied with updates before updating the firmware.
1
Save the downloaded firmware to the root folder of a USB memory
device.
2
Press PROGRAM on the front panel to select “UPDATE”.
3
Connect the USB memory device to the USB jack.
4
To start firmware update, press INFO on the front panel.
Checking the firmware version (VERSION)
ENHANCER
LINK
ECO
MASTER
OUT
2
-
R
es
Hi
YPAO
VOL.
A
-
DRC
SLEEP
STEREO
PARTY
TUNED
ZONE
3 B2 A
VOL .
FPR
SL
SW
SR
SBL SB SBR
FPL
MUT E V IRT UAL
VERSIONxx.xx
Check the version of firmware currently installed on the unit.
Note
It may take a while until the firmware version is displayed.
En
68
APPENDIX
Frequently asked questions
The frequently asked questions from customers and the answers are shown below.
The new speaker system does not provide an ideal sound balance...
If you have changed speakers or have a new speaker system, use YPAO to optimize
the speaker settings again (p.25). If you want to adjust the speaker settings manually,
use “Speaker” in the “Setup” menu (
p.54).
We want to set limitations on the volume control...
If someone accidentally operates the controls on the main unit or remote control, the
volume may suddenly increase. This may also cause injury or damage the unit or
speakers. We recommend using “
Max Volume” in the “Setup” menu to set the
maximum volume level for the unit in advance (p.60).
I want to fix the volume when turning on the unit...
By default, the volume level when the unit last entered standby mode is automatically
applied. If you want to fix the volume, use “
Initial Volume” in the “Setup” menu to set
the volume to be applied when the receiver is turned on (p.60).
The volume varies depending on the input sources...
You can correct volume differences between input sources by utilizing “Input Trim” in
the “Option” menu (p.49).
HDMI Control does not work at all...
To use HDMI Control, you need to perform the HDMI Control link setup (p.80). After
connecting HDMI Control-compatible devices (such as BD/DVD players) to the unit,
enable HDMI Control on each device and perform the HDMI Control link setup. This
setup is required every time you add a new HDMI Control-compatible device to your
system. For information on how HDMI Control works between your TV and playback
devices, refer to the instruction manuals for each device.
I want to change the input source name...
By default, input source names (such as “HDMI1” and “AV 1”) are displayed on the
front display when an input source is selected. If you want to rename them as you like,
use “Input Rename”
(p.62) in the “Setup” menu.
I want to prevent accidental changes to the settings...
You can protect the settings configured on the unit (such as speaker settings) by
utilizing “
Memory Guard” in the “Setup” menu (p.63).
The unit’s remote control is simultaneously controlling another Yamaha
product as well as the unit...
When using multiple Yamaha products, the remote control may work on another
Yamaha product or another remote control may work on the unit. If this happens,
register different remote control IDs for the devices that you want to control with each
remote control (p.67).
The combination of video/audio input jacks does not match an external
device...
Use “Audio In” in the “Option” menu to change the combination of video/audio input
jacks so that it matches the output jack(s) of your external device (
p.21).
Video and audio are not synchronized...
Use “Lipsync” in the “Setup” menu to adjust the delay between video and audio output
(p.59).
I want to hear audio from the TV speakers...
Use “Audio Output” in the “Setup” menu to enable audio output from the TV speakers
(p.57).
I want to change the on-screen menu language...
Use “Language” in the “Setup” menu to select a language from English, Japanese,
French, German, Spanish, Russian, Italian and Chinese (
p.24).
I want to update the firmware...
Use “UPDATE” in the “ADVANCED SETUP” menu to update the unit’s firmware (p.68).
En
69
Troubleshooting
Refer to the table below when the unit does not function properly.
If the problem you are experiencing is not listed below or if the instructions below do not help, turn off the unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
First, check the following:
1
The power cables of the unit, TV and playback devices (such as BD/DVD players) are connected to AC wall outlets securely.
2
The unit, subwoofer, TV and playback devices (such as BD/DVD players) are turned on.
3
The connectors of each cable are securely inserted in to jacks on each device.
Power, system and remote control
Problem Cause Remedy
The power does not turn on.
The protection circuitry has been activated three times
consecutively. If the unit is in this condition, the standby indicator
on the unit blinks when you try to turn on the power.
As a safety precaution, capability to turn on the power is disabled. Contact your
nearest Yamaha dealer or service center to request repair.
The power does not turn off.
The internal microcomputer has frozen, due to an external electric
shock (such as lightning or excessive static electricity) or to a drop
in the power supply voltage.
Hold down z (power) on the front panel for more than 15 seconds to reboot the
unit. (If the problem persists, disconnect the power cable from the AC wall outlet
and plug it again.)
The power turns off (standby mode) immediately.
The unit was turned on while a speaker cable was shorted.
Twist the bare wires of each speaker cable firmly and reconnect to the unit and
speakers (
p.17).
The unit enters standby mode automatically.
The sleep timer worked. Turn on the unit and start playback again.
The auto-standby function activated because the unit was not used
for the specified time.
To disable the auto-standby function, set “Auto Power Standby” in the “Setup”
menu to “Off
” (p.61).
The speaker impedance setting is incorrect. Set the speaker impedance to match your speakers (p.66).
The protection circuitry has been activated because of a short
circuit.
Twist the bare wires of each speaker cable firmly and reconnect to the unit and
speakers (p.
17).
The unit is not reacting.
The internal microcomputer is frozen, due to an external electric
shock (such as lightning or excessive static electricity) or to a drop
in the power supply voltage.
Hold down z (power) on the front panel for more than 15 seconds to reboot the
unit. (If the problem persists, disconnect the power cable from the AC wall outlet
and plug it again.)
En
70
Problem Cause Remedy
The unit cannot be controlled using the remote
control.
The unit is out of the operating range. Use the remote control within the operating range (p.4).
The batteries are weak. Replace with new batteries.
The unit’s remote control sensor is exposed to direct sunlight or
strong lighting.
Adjust the lighting angle, or reposition the unit.
The remote control IDs of the unit and the remote control are not
identical.
Change the remote control ID of the unit or the remote control (p.67).
Cannot select the desired input source even if
“INPUT” is pressed.
The function which skips some input sources is set. Set “Input Skip” of the desired input source in the “Setup” menu to “Off” (p.63).
The RED/GREEN/YELLOW/BLUE keys of the
remote control do not operate.
The device which is connected to the unit via HDMI does not
support the operation of the RED/GREEN/
YELLOW/BLUE keys.
Use a device which supports the operation of the RED/GREEN/YELLOW/BLUE
keys.
The settings of the RED/GREEN/YELLOW/BLUE keys of the unit's
remote control have been changed.
Set the “Remote Color Key” settings in the “Setup” menu to “Default” (p.64).
Audio
Problem Cause Remedy
No sound.
Another input source is selected. Select an appropriate input source with the input selection keys.
Signals that the unit cannot reproduce are being input.
Some digital audio formats cannot be played back on the unit. To check the
audio format of the input signal, use “Signal Info.” in the “Option” menu (
p.49).
The cable connecting the unit and playback device is defective. If there is no problem with the connection, replace with another cable.
The volume cannot be increased.
The maximum volume is set. Use “Max Volume” in the “Setup” menu to adjust the maximum volume (p.60).
A device connected to the output jacks of the unit is not turned on. Turn on all devices connected to the output jacks of the unit.
No sound is coming from a specific speaker.
The playback source does not contain a signal for the channel. To check it, use “Signal Info.” in the “Option” menu (p.49).
The currently selected sound program/decoder does not use the
speaker.
To check it, select “5ch Stereo” (p.32).
Audio output of the speaker is disabled.
Perform YPAO (p.25) or use “Configuration” in the “Setup” menu to change the
speaker settings (p.54).
The volume of the speaker is set too low.
Perform YPAO (p.25) or use “Level” in the “Setup” menu to adjust the speaker
volume (
p.56).
The speaker cable connecting the unit and the speaker is
defective.
If there is no problem with the connection, replace with another speaker cable.
The speaker is malfunctioning.
To check it, replace with another speaker. If the problem persists, the unit may be
malfunctioning.
En
71
Problem Cause Remedy
No sound is coming from the subwoofer.
The playback source does not contain Low Frequency Effect (LFE)
or low-frequency signals.
To check it, set “Extra Bass” in the “Setup” menu to “On”, in order to output the
front channel low-frequency components from the subwoofer (
p.55).
Subwoofer output is disabled. Perform YPAO (p.25) or set “Subwoofer” in the “Setup” menu to “Use” (p.54).
The volume of the subwoofer is too low. Adjust the volume on the subwoofer.
The subwoofer has been turned off by its auto-standby function. Disable the auto-standby function of the subwoofer or adjust its sensitivity level.
No sound from the playback device (connected to
the unit with HDMI).
The TV does not support HDCP (High-bandwidth Digital Content
Protection).
Refer to the instruction manuals for the TV and check the TV’s specifications.
The number of devices connected to the HDMI OUT jack exceeds
the limit.
Disconnect some of the HDMI devices.
No sound from the TV (when HDMI Control is
used).
The TV is set to output audio from the TV speakers.
Change the audio output setting on your TV so that the TV audio is output from
the speakers connected to the unit.
A TV that does not support ARC is connected to the unit only with
an HDMI cable.
Use a digital optical cable to make an audio connection (p.19).
(If the TV is connected to the unit with an audio cable)
The TV audio input setting does not match the actual connection.
Use “TV Audio Input” in the “Setup” menu to select the correct audio input jack
(p.57).
(If you are trying to use ARC)
ARC is disabled on the unit or TV.
Set “ARC” in the “Setup” menu to “On” (p.58). Also, enable ARC on the TV.
When playing back DSD audio, the unit disables
the audio output from a TV.
The unit does not support DSD audio output from a TV. Change the audio output setting on the playback device to PCM.
Only the front speakers work on multichannel
audio.
The playback device is set to output 2-channel audio (such as
PCM) only.
To check it, use “Signal Info.” in the “Option” menu (p.49). If necessary, change
the digital audio output setting on the playback device.
Noise/hum is heard.
The unit is too close to another digital or radio frequency device. Move the unit further away from the device.
The cable connecting the unit and playback device is defective. If there is no problem with the connection, replace with another cable.
The sound is distorted.
The volume of the unit is too high.
Turn down the volume. If “ECO Mode” in the “Setup” menu is set to “On”, set it to
“Off
” (p.61).
A device connected to the unit’s output jacks is not turned on. Turn on all devices connected to the unit’s output jacks.
En
72
Video
Problem Cause Remedy
No video.
Another input source is selected on the unit. Select an appropriate input source with the input selection keys.
Another input source is selected on the TV. Switch the TV input to display the video from the unit.
The video signal output from the unit is not supported by the TV.
Check the video output setting of the playback device. For information about
video signals supported by the TV, refer to the instruction manuals for the TV.
The cable connecting the unit and TV (or playback device) is
defective.
If there is no problem with the connection, replace with another cable.
No video from the playback device (connected to
the unit with HDMI).
The input video signal (resolution) is not supported by the unit.
To check the information about the current video signal (resolution), use “Signal
Info.
” in the “Option” menu (p.49). For information about video signals supported
by the unit, see “HDMI signal compatibility” (p.82).
The TV does not support HDCP (High-bandwidth Digital Content
Protection).
Refer to the instruction manuals for the TV and check the TV’s specifications.
The number of devices connected to the HDMI OUT jack is over
the limit.
Disconnect some of the HDMI devices.
No image (contents required the HDCP 2.2 -
compatible HDMI device) from the playback
device connected to the unit with HDMI.
The TV (HDMI input jack) does not support HDCP 2.2. (The
Warning message can be displayed on the TV screen.)
Connect the unit to the TV (HDMI input jack) that supports HDCP 2.2.
The menu of the unit is not displayed on the TV.
The TV is not connected to the unit via HDMI.
You can display the menu of the unit on the TV only when they are connected
with an HDMI cable. If necessary, use an HDMI cable to connect them (
p.19 to
p.20).
Another input source is selected on the TV. Switch the TV input to display the video from the unit (HDMI OUT jack).
En
73
FM/AM radio
Problem Cause Remedy
FM radio reception is weak or noisy.
There is multi-path interference. Adjust the FM antenna height or orientation, or place it in a different location.
Your area is too far from the FM station transmitter.
To select monaural FM radio reception “FM Mode” in the “Option” menu to
Mono” (p.37).
Use an outdoor FM antenna.
AM radio reception is weak or noisy.
The noises may be caused by fluorescent lamps, motors,
thermostats, or other electrical equipment.
It is difficult to completely eliminate noise. It may be reduced by using an outdoor
AM antenna.
Radio stations cannot be selected automatically.
Your area is too far from the FM station transmitter.
Select the station manually (p.37).
Use an outdoor antenna. We recommend using a sensitive multi-element
antenna.
The AM radio signal is weak.
Adjust the AM antenna orientation.
Select the station manually (p.37).
Use an outdoor AM antenna. Connect it to the ANTENNA (AM) jack together with
the supplied AM antenna.
AM radio stations cannot be registered as
presets.
Auto Preset has been used.
Auto Preset is for registering FM radio stations only. Register AM radio stations
manually (
p.38).
USB
Problem Cause Remedy
The unit does not detect the USB device.
The USB device is not connected to the USB jack securely. Turn off the unit, reconnect your USB device, and turn the unit on again.
The file system of the USB device is not FAT 16 or FAT 32. Use a USB device with FAT 16 or FAT 32 format, except USB HDDs.
Folders and files in the USB device cannot be
viewed.
The folder structure not supported by the unit is applied.
The unit supports folder hierarchies of up to eight levels and up to 65,000 files
per level. If necessary, modify the folder structure on your USB device.
En
74
Bluetooth®
Problem Cause Remedy
Cannot make the unit pair with a Bluetooth
device.
Another Bluetooth device is connected. Terminate current Bluetooth connection, and perform pairing with the new device.
This unit and the device are too far apart. Move the device closer to this unit.
There is a device (microwave oven, wireless LAN, etc.) that outputs
signals in the 2.4 GHz frequency band nearby.
Move this unit away from the device that is emitting radio-frequency signals.
The Bluetooth device does not support A2DP. Perform pairing with a device which supports A2DP.
Cannot make a Bluetooth connection.
Another Bluetooth device is connected.
Terminate current Bluetooth connection, then establish a Bluetooth connection
with that device again.
The Bluetooth function of the device is turned off. Turn on the Bluetooth function of the device.
The pairing information has been deleted.
Delete the pairing information on the device, and then perform pairing again
(p.42).
This unit can be paired with sixteen devices. If pairing with a seventeenth device
is performed, the pairing information with the earliest connection date will be
deleted.
The pairing information is removed from/not registered on the
Bluetooth connection list.
Perform paring again (p.42).
No sound is produced, or the sound is
interrupted during playback.
The volume of the connecting device is set too low. Turn up the volume of the connecting device.
The connecting device is not set to send Bluetooth audio signals to
the unit.
Switch the output of Bluetooth audio signals of the connecting device to the unit.
The Bluetooth connection of the unit with the device has
terminated.
Perform Bluetooth connection operations again (p.42).
There is a device (microwave oven, wireless LAN, etc.) that outputs
signals in the 2.4 GHz frequency band nearby.
Move this unit away from the device that is emitting radio-frequency signals.
This unit and the connecting device are too far apart. Move the connecting device closer to this unit.
En
75
Error indications on the front display
Refer to the table below when the error message is indicated on the front display.
Message Cause Remedy
Access error
The unit cannot access the USB device. Turn off the unit and reconnect your USB device. If the problem persists, try another USB device.
Check SP Wires
The speaker cables short circuit. Twist the bare wires of the cables firmly and connect to the unit and speakers properly.
Internal Error
An internal error has occurred. Contact the nearest authorized Yamaha dealer or service center.
No content
There are no playable files in the selected folder. Select a folder that contains files supported by the unit.
Not found
The Bluetooth device is not found.
Place the Bluetooth device within 10 m (32 ft) of the Bluetooth receiver.
Perform pairing again.
RemID Mismatch
The remote control IDs of the unit and the remote control are not
identical.
Change the remote control ID of the unit or the remote control (p.67).
En
76
Glossary
This is a glossary of the technical terms used in this manual.
Audio information
n
Audio decoding format
Dolby Digital
Dolby Digital is a compressed digital audio format developed by Dolby Laboratories, Inc. that
supports 5.1-channel audio. This technology is used for audio on most DVD disc.
Dolby Pro Logic II
Dolby Pro Logic II enables 5-channel playback from 2-channel sources. There are three modes
available: “Music mode” for music sources, “Movie mode” for movie sources, and “Game mode”
for game sources.
Dolby TrueHD
Dolby TrueHD is an advanced lossless audio format developed by Dolby Laboratories, Inc. to
offer a high-definition home theater experience with the quality of the studio master. Dolby TrueHD
can carry up to eight channels of 96 kHz/24-bit audio (up to six channels of 192 kHz/24-bit audio)
simultaneously. This technology is used for audio on BD (Blu-ray Disc).
DTS 96/24
DTS 96/24 is a compressed digital audio format that supports 5.1-channel and 96 kHz/24-bit
audio. This format remains fully compatible with the existing multichannel audio systems that
support DTS Digital Surround. This technology is used for music DVDs, etc.
DTS Digital Surround
DTS Digital Surround is a compressed digital audio format developed by DTS, Inc. that supports
5.1-channel audio. This technology is used for audio on most DVD discs.
DTS Express
DTS Express is a compressed digital audio format that supports 5.1-channel audio and allows a
higher compression rate than the DTS Digital Surround format developed by DTS, Inc. This
technology is developed for audio streaming services on the Internet and secondary audio on BD
(Blu-ray Disc).
DTS-HD High Resolution Audio
DTS-HD High Resolution Audio is a compressed digital audio format developed by DTS, Inc. that
supports 7.1-channel and 96 kHz/24-bit audio. DTS-HD High Resolution Audio remains fully
compatible with the existing multichannel audio systems that support DTS Digital Surround. This
technology is used for audio on most BD (Blu-ray Disc).
DTS-HD Master Audio
DTS-HD Master Audio is an advanced lossless audio format developed to offer a high-definition
home theater experience with the quality of the studio master by DTS, Inc. DTS-HD Master Audio
can carry up to eight channels of 96 kHz/24-bit audio (up to six channels of 192 kHz/24-bit audio)
simultaneously. This technology is used for audio on BD (Blu-ray Disc).
DTS Neo: 6
DTS Neo: 6 enables 6-channel playback from 2-channel sources. There are two modes available:
“Music mode” for music sources and “Cinema mode” for movie sources. This technology provides
discrete full-bandwidth matrix channels of surround sound.
DSD (Direct Stream Digital)
DSD (Direct Stream Digital) technology stores audio signals on digital storage media, such as
SACD (Super Audio CDs). The signals are stored at a high-frequency sampling rate of 2.8224
MHz. The highest frequency response is equal to or higher than 100 kHz, with a dynamic range of
120 dB. This technology offers better audio quality than that used for CDs.
MP3
One of the compressed digital audio format used by MPEG. With psychoacoustic technologies,
this compression method achieves a high compression rate. Reportedly, it is capable of
compressing data quantity by about 1/10 maintaining a certain level of audio quality.
MPEG-4 AAC
An MPEG-4 audio standard. It is used for mobile telephones, portable audio players, and audio
streaming services on Internet because it allows a high compression rate of data while
maintaining better audio quality than MP3.
PCM (Pulse Code Modulation)
PCM is a signal format under which an analog audio signal is digitized, recorded, and transmitted.
This technology is the basis of all other audio format. This technology is used as a lossless audio
format called Linear PCM for audio on a variety of media, including CDs and BD (Blu-ray Disc).
Sampling frequency/Quantization bit
Sampling frequency and quantization bits indicate the quantity of information when an analog
audio signal is digitized. These values are noted as in the following example: “48 kHz/24-bit”.
Sampling frequency
Sampling frequency (the number of times the signal is sampled per second) is called the
sampling rate. When the sampling frequency is higher, the range of frequencies that can be
played back are wider.
Quantization bit
The number of quantization bits indicate the degree of accuracy when converting the sound
level into a numeric value. When the number of quantized bits is higher, the expression of the
sound level is more accurate.
WAV
Windows standard audio file format, which defines the method of recording the digital data
obtained by converting audio signals. By default, the PCM method (no compression) is used, but
you can also use other compression methods.
WMA (Windows Media Audio)
One of the compressed digital audio formats developed by Microsoft Corporation. With
psychoacoustic technologies, this compression method achieves a high compression rate.
Reportedly, it is capable of compressing data quantity by about 1/20 maintaining a certain level of
audio quality.
En
77
n
Others
LFE (Low Frequency Effects) 0.1 channel
This channel reproduces low-frequency bass signals and has a frequency range from 20 Hz to
120 Hz. This channel is added to the channels for all bands with Dolby Digital or DTS to enhance
low frequency audio effects. This channel is labeled 0.1 because it is limited to only low frequency
audio.
Lip sync
Video output sometimes lags behind audio output due to the complexity of signal processing
caused by an increase in video signal capacity. Lip sync is a technique for automatically
correcting the timing lag between audio and video output.
HDMI and video information
Composite video signal
With the composite video signal system, color, brightness, and synchronization data signals are
combined and transmitted with a single cable.
Deep Color
Deep Color is a technology that HDMI specification supports. Deep Color increases the number of
available colors within the boundaries defined by the RGB or YCbCr color space. Conventional
color systems process the color using 8 bits. Deep Color processes the color with 10, 12, or 16
bits. This technology allows HDTVs and other displays to increase from millions of colors to
billions of colors and eliminate on-screen color banding for smooth tonal transitions and subtle
gradations between colors.
HDMI
HDMI (High-Definition Multimedia Interface) is the world-wide standard interface for digital audio/
video signal transmission. This interface transmits both digital audio and digital video signals
using a single cable without any loss. HDMI complies with HDCP (High-bandwidth Digital Content
Protection) and provides a secure audio/video interface. For further information on HDMI, visit the
HDMI website at “http://www.hdmi.org/”
.
x.v.Color
“x.v.Color” is a technology that the HDMI specification supports. It is a more extensive color
space than sRGB and allows the expression of colors that were not hitherto possible. While
remaining compatible with the color gamut of sRGB standards, “x.v.Color” expands the color
space, and thus can produce more vivid, natural images.
Yamaha technologies
CINEMA DSP (Digital Sound Field Processor)
Since the surround sound systems were originally designed for use in movie theaters, their effect
is best experienced in a theater that has many speakers designed for acoustic effects. Since
home conditions (such as room size, wall material, and number of speakers) can differ so widely,
it is inevitable that there are differences in the sound that you hear. Based on a wealth of actually
measured data, CINEMA DSP, Yamaha’s original DSP technology provides the audiovisual
experience of a movie theater in your own home.
Compressed Music Enhancer
The Compressed Music Enhancer feature compensates for missing harmonics in compression
music formats (such as MP3). As a result, this technology provides improved performance for the
overall sound system.
SILENT CINEMA
Yamaha has developed a natural, realistic sound effect DSP algorithm for headphones.
Parameters for headphones have been set for each sound program, so that accurate
representations of all the sound programs can be enjoyed on headphones.
Virtual CINEMA DSP
Virtual CINEMA DSP allows the system to virtually reproduce the sound field of the surround
speakers with front left and right speakers. Even if the surround speakers are not connected, the
unit creates the realistic sound field in a listening room.
YPAO (Yamaha Parametric room Acoustic Optimizer)
The Yamaha Parametric room Acoustic Optimizer (YPAO) function detects speaker connections,
measures the distances from them to your listening position(s), and then automatically optimizes
the speaker settings, such as volume balance and acoustic parameters, to suit your room.
En
78
Supported devices and file formats
The following devices and file formats can be used by the unit.
Supported devices
n
USB devices
This unit supports USB mass storage class devices (e.g., flash memories or
portable audio players) using FAT16 or FAT32 format.
Do not connect devices other than USB mass storage class devices (such as USB
chargers or USB hubs), PCs, card readers, an external HDD, etc.
USB devices with encryption cannot be used.
Operation of all USB devices cannot be guaranteed.
n
Bluetooth® devices
Bluetooth devices that support A2DP can be used.
Operation of all Bluetooth devices cannot be guaranteed.
File formats
n
USB
The unit supports WAV (PCM format only), MP3, WMA and MPEG-4 AAC files (1- or
2-channel audio only).
The unit is compatible with sampling rate of up to 48 kHz.
Digital Rights Management (DRM) contents cannot be played back.
Video signal flow
Video signals input from a video device to the unit are output to a TV as shown below.
HDMIHDMI
VIDEOVIDEO
HDMI HDMI
VIDEO VIDEO
Video device The unit TV
HDMI connection
Composite video connection
HDMI in HDMI out
VIDEO in VIDEO out
En
79
Information on HDMI
The additional information on HDMI is as follows.
HDMI Control
HDMI Control allows you to operate external devices via HDMI. If you connect a TV
that supports HDMI Control to the unit with an HDMI cable, you can control the unit
(such as power and volume) with TV remote control operations. You can also control
playback devices (such as HDMI Control-compatible BD/DVD players) connected to
the unit with an HDMI cable.
n
Operations available from the TV’s remote control
Standby synchronization
Volume control including mute
Switching to input audio from the TV when the TV input is switched to its built-in
tuner
Switching to input video/audio from the selected playback device
Switching between audio output devices (the unit or TV speaker)
(Example)
HDMI Control HDMI Control
The unit turns off
(standby)
Playback device
also turns off
Turn off the TV
n
Operations available from the unit’s remote control
Starting playback on the playback device and turning on the TV with a scene
selection (
p.31)
Switching the TV input to display the “Setup” menu (when SETUP is pressed)
Controlling the playback device (playback and menu operations)
(Example)
HDMI Control HDMI Control
Press SCENE (BD/DVD)
Playback starts
Turns on and displays
video from the playback
device
To use HDMI Control, you need to perform the following HDMI Control link setup after
connecting the TV and playback devices.
For details on settings and operating your TV, refer to the instruction manual for the TV.
Note
This setup is required every time you add a new HDMI Control-compatible device to your system.
1
Turn on the unit, TV, and playback devices.
2
Configure the settings of the unit.
1
Switch the TV input to display video from the unit.
2
Press SETUP.
MUTE
TOP MENU
HOME
POP-UP/MENU
DISPLAYRETURN
SETUP
OPTION
ENTER
TUNING
PRESET
MUTE
TUNING
MEMORY
TOP MENU
HOME
POP-UP/MENU
DISPLAYRETURN
SETUP
OPTION
ENTER
FM/AM
VOLUME
PROGR AM
USB
STRAIGHT
ENHANCER BASS
BLUETOOTH
INPU T
BD
DVD
TV
CD
SC ENE
RADIO
SLEEP
BLUE
YELLOWGREEN
RED
MUT
E
TO
P MENU
HOME
POP-UP/MENU
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
DISPLADISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLADISPLA
DISPLADISPLA
DISPLADISPLA
DISPLADISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
DISPLA
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURNRETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
RETURN
OPTION
OPTION
SETUP
ENTER
Cursor keys
En
80
3
Use the cursor keys to select “HDMI” and press ENTER.
4
Use the cursor keys (q/w) to select “HDMI Control” and the cursor keys
(e/r) to select “On” as shown below.
5
If you made a digital optical cable connection between the TV and the
unit, use the cursor keys (q/w) to select “TV Audio Input” and the
cursor keys (e/r) to select “AUDIO1”.
6
Press SETUP.
3
Enable HDMI Control on the TV and playback devices (such as
HDMI Control-compatible BD/DVD players).
4
Turn off the main power of the TV and then turn off the unit and
playback devices.
5
Turn on the unit and playback devices and then turn on the TV.
6
Switch the TV input to display the video from the unit.
7
Check the followings.
On the unit: The input to which the playback device is connected is
selected. If not, select the input source manually.
On the TV: The video from the playback device is displayed.
8
Check that the unit is properly synchronized with the TV by
turning off the TV or adjusting the TV volume with the TV remote
control.
Note
If HDMI Control does not work properly, the problem may be solved by turning the playback device off and
on again, or by unplugging the power plug and plugging it in again. Also, HDMI Control may not work
properly if the number of connected devices exceeds the limit. In this case, disable HDMI Control on
devices not in use.
If the unit is not synchronized to the TV’s power operations, check the priority of the audio output setting
on the TV.
If you reconnect the HDMI cable, perform the procedure 5-8 again.
We recommend using TV and playback devices from the same manufacturer so that HDMI Control works
more effectively.
En
81
Audio Return Channel (ARC)
ARC allows you to input TV audio to the unit with the HDMI cable which transmits video
signal to the TV.
Check the following after the HDMI Control settings.
1
Select a TV program with the TV remote control.
2
Check that the input source of the unit will be automatically
switched to “AV 2” and the TV audio will be played back on the
unit.
If you cannot hear the TV audio, check the following:
“ARC” (p.58) in the “Setup” menu is set to “On”.
The HDMI cable is connected to the ARC-compatible HDMI jack (HDMI
jack marked “ARC”) on the TV.
Some HDMI jack on the TV is not compatible with ARC. For details, refer
to the instruction manual for the TV.
Note
If the audio is interrupted while using ARC, set “ARC” (p.58) in the “Setup” menu to “Off” and use a digital
optical cable to input TV audio to the unit (
p.19).
When using ARC, connect a TV with an HDMI cable that supports ARC.
“AV 2” is set as TV audio input at the factory. If you have connected any external device to the AV 2 jacks,
use “TV Audio Input” (p.57)
in the “Setup” menu to change the TV audio input assignment. To use the
SCENE function (p.31), you also need to change the input assignment for SCENE (TV).
HDMI signal compatibility
When CPPM copy-protected DVD-Audio is played back, video/audio signals may
not be output, depending on the type of the DVD player.
The unit is not compatible with HDCP-incompatible HDMI or DVI devices. For
details, refer to the instruction manual for each device.
To decode audio bitstream signals on the unit, set the input source device
appropriately so that the device outputs the bitstream audio signals directly (does
not decode the bitstream signals on the playback device). For details, refer to the
instruction manual for the playback device.
En
82
Trademarks
The trademarks used in this manual are as follows.
Manufactured under license from Dolby Laboratories. Dolby,
Pro Logic, and the double-D symbol are trademarks of Dolby
Laboratories.
For DTS patents, see http://patents.dts.com. Manufactured
under license from DTS Licensing Limited. DTS, DTS-HD, the
Symbol, & DTS and the Symbol together are registered
trademarks of DTS, Inc.
© DTS, Inc. All Rights Reserved.
The terms HDMI, the HDMI Logo, and High-Definition
Multimedia Interface are trademarks or registered trademarks
of HDMI Licensing LLC in the United States and other
countries.
x.v.Color™
“x.v.Color” is a trademark of Sony Corporation.
The Bluetooth
®
word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of such
marks by Yamaha Corporation is under license.
App Store is a service mark of Apple Inc.
Android™ is a trademark of Google Inc.
“SILENT CINEMA” is a trademark of Yamaha Corporation.
Google Noto Fonts
This product uses the following fonts.
Copyright © June 2015, Google
(https://www.google.com/get/noto/#sans-lgc
), with Reserved
Font Name Noto Sans Version 1.004.
Copyright © June 2015, Google
(https://www.google.com/get/noto/help/cjk/), with Reserved
Font Name Noto Sans CJK Version 1.004.
This Font Software is licensed under the SIL Open Font
License, Version1.1.
This license is available with a FAQ at:
http://scripts.sil.org/OFL
En
83
Specifications
The specifications of this unit are as follows.
Input jacks
Analog Audio
Audio x 3
Digital Audio (Supported frequencies: 32 kHz to 96 kHz)
Optical x 1
Coaxial x 2
Video
Composite x 3
HDMI Input
HDMI x 4
Other jacks
USB x 1 (USB2.0)
Output jacks
Analog Audio
Speaker Out x 5 (FRONT L/R, CENTER, SURROUND L/R)
Subwoofer Out x 1
Headphone x 1
Video
Composite x 1
HDMI Output
HDMI OUT x 1
Other jacks
YPAO MIC x 1
HDMI
HDMI Features:
4K UltraHD Video (include 4K/60, 50Hz 10/12bit), 3D Video, ARC (Audio Return Channel), HDMI
Control (CEC), Auto Lip Sync, Deep Color, “x.v.Color”, HD audio playback, 21:9 Aspect Ratio,
BT.2020 Colorimetry, HDR Compatible
Video Format (Repeater Mode)
VGA
480i/60 Hz
576i/50 Hz
480p/60 Hz
576p/50 Hz
720p/60 Hz, 50 Hz
1080i/60 Hz, 50 Hz
1080p/60 Hz, 50 Hz, 30 Hz, 25 Hz, 24 Hz
4K/60Hz, 50Hz, 30 Hz, 25 Hz, 24 Hz
Audio Format
Dolby TrueHD
Dolby Digital Plus
Dolby Digital
DTS-HD Master Audio
DTS-HD High Resolution Audio
DTS Express
DTS
DSD 2-ch to 6-ch
PCM 2-ch to 8-ch (Max. 192 kHz/24-bit)
Content Protection: HDCP 2.2 compatible
Link Function: CEC supported
TUNER
Analog Tuner
[U.K. and Europe models]
FM/AM with Radio Data System x 1 (TUNER)
[Other models]
FM/AM x 1 (TUNER)
En
84
USB
Capable of Mass Storage Class USB Memory
Current Supply Capacity: 0.5 A
Bluetooth
Bluetooth version
Ver. 2.1+EDR
Supported profile
A2DP
Supported codec
SBC
Wireless output
Bluetooth Class 2
Radio Frequency (Operational Frequency)
2402 MHz to 2480 MHz
Maximum Output Power (E.I.R.P)
4 dBm (2.51 mW)
Maximum communication distance
10 m (33 ft) without interference
Compatible Decoding Formats
Decoding Format
Dolby TrueHD, Dolby Digital Plus
Dolby Digital
DTS-HD Master Audio, DTS-HD High Resolution Audio, DTS Express
DTS, DTS 96/24
Post Decoding Format
Dolby Pro Logic
Dolby Pro Logic II Music, Dolby Pro Logic II Movie, Dolby Pro Logic II Game
DTS Neo: 6 Music, DTS Neo: 6 Cinema
Audio Section
Rated Output Power (2-channel driven)
[U.S.A. and Canada models] (20 Hz to 20 kHz, 0.09% THD, 8 )
[Other models] (20 Hz to 20 kHz, 0.09% THD, 6 )
Front L/R 70 W+70 W
[U.S.A. and Canada models] (1 kHz, 0.9% THD, 8 )
Front L/R 85 W+85 W
Center 85 W
Surround L/R 85 W+85 W
Rated Output Power (1-channel driven)
[U.S.A. and Canada models] (1 kHz, 0.9% THD, 8 )
[Other models] (1 kHz, 0.9% THD, 6 )
Front L/R 100 W/ch
Center 100 W/ch
Surround L/R 100 W/ch
Maximum Effective Output Power (1-channel driven)
[U.S.A. and Canada models]
(1 kHz, 10% THD, 8 )
Front L/R, Center, Surround L/R
130 W/ch
(1 kHz, 10% THD, 6 )
Front L/R, Center, Surround L/R
145 W/ch
[Other models] (1 kHz, 10% THD, 6 )
Front L/R, Center, Surround L/R 135 W/ch
Dynamic Power (IHF)
[U.S.A. and Canada models]
Front L/R (8/6/4/2 )
110/130/160/180 W
[Other models]
Front L/R (6/4/2 )
110/130/150 W
Damping Factor
Front L/R, 20 Hz to 20 kHz, 8
100 or more
Input Sensitivity / Input Impedance
AV 2 etc. (1 kHz, 100 W/6 ) 200 mV/47 k
Maximum Input Signal
AV 2 etc. (1 kHz, 0.5% THD, Effect On) 2.3 V
En
85
Output Level / Output Impedance
SUBWOOFER
1 V/1.2 k
Headphone Jack Rated Output / Impedance
AV 2 etc. (1 kHz, 50 mV, 8 ) 100 mV/470
Frequency Response
AV 2 etc. to Front (10 Hz to 100 kHz) +0/-3 dB
Signal to Noise Ratio (IHF-A Network)
AV 2 etc. (Input 1 k Shorted, Speaker Out)
110 dB or more
Residual Noise (IHF-A Network)
Front L/R (Speaker Out) 150 μV or less
Channel Separation
AV 2 etc. (Input 1 k Shorted, 1 kHz/10 kHz)
70 dB/50 dB or more
Volume Control
Range MUTE, -80 dB to +16.5 dB
Step 0.5 dB
Tone Control Characteristics
Bass Boost/Cut ±6 dB/0.5 dB Step at 50 Hz
Bass Turnover 350 Hz
Treble Boost/Cut ±6 dB/0.5 dB Step at 20 kHz
Treble Turnover 3.5 kHz
Filter Characteristics
(fc=40/60/80/90/100/110/120/160/200 Hz)
H.P.F. (Front, Center, Surround) 12 dB/oct.
L.P.F. (Subwoofer) 24 dB/oct.
Video Section
Video Signal Type
[U.S.A., Canada, Korea, Taiwan, Brazil and General models] NTSC
[Other models] PAL
Video Signal Level
Composite
1 Vp-p/75
Video Maximum Input Level
1.5 Vp-p or more
Video Signal to Noise Ratio
50 dB or more
FM Section
Tuning Range
[U.S.A. and Canada models] 87.5 MHz to 107.9 MHz
[Asia, Taiwan, Brazil and General models] 87.5/87.50 MHz to 108.0/108.00 MHz
[U.K. and Europe models] 87.50 MHz to 108.00 MHz
[Other models] 87.50 MHz to 108.00 MHz
50 dB Quiet Sensitivity (IHF, 1 kHz, 100% MOD.)
Mono 3 μV (20.8 dBf)
Signal to Noise Ratio (IHF)
Mono 65 dB
Stereo 64 dB
Harmonic Distortion (IHF, 1 kHz)
Mono 0.5%
Stereo 0.6%
Antenna Input
75 unbalanced
AM section
Tuning Range
[U.S.A. and Canada models] 530 kHz to 1710 kHz
[Asia, Taiwan, Brazil and General models] 530/531 kHz to 1710/1611 kHz
[U.K. and Europe models] 531 kHz to 1611 kHz
[Other models] 531 kHz to 1611 kHz
En
86
General
Power Supply
[U.S.A. and Canada models] AC 120 V, 60 Hz
[Taiwan, Brazil and General models] AC110 to 120/220 to 240 V, 50/60 Hz
[Korea model] AC 220 V, 60 Hz
[Australia model] AC 240 V, 50 Hz
[U.K. and Europe models] AC 230 V, 50 Hz
[Asia model] AC 220 to 240 V, 50/60 Hz
Power Consumption
260 W
Standby Power Consumption
HDMI Control Off
[Taiwan, Brazil and General models] 0.5 W
[Other models] 0.3 W
HDMI Control On (No Signals) 0.9 W
Bluetooth Standby ON 0.6 W
HDMI Control On, Bluetooth Standby ON 1.2 W
Maximum Power Consumption
[Taiwan, Brazil and General models] 470 W
Dimensions (W x H x D)
435 x 151 x 315 mm (17-1/8” x 6” x 12-3/8”)
Weight
7.4 kg (16.3 lbs)
* The contents of this manual apply to the latest specifications as of the publishing date. To obtain
the latest manual, access the Yamaha website then download the manual file.
En
87
Yamaha Global Site
http://www.yamaha.com/
Yamaha Downloads
http://download.yamaha.com/
Manual Development Group
© 2017 Yamaha Corporation
Published 02/2017 NV-A0
YJ186A0/EN1

Transcripción de documentos

AV Receiver Owner's Manual • This unit is a product for enjoying video and music at home. • This manual explains preparations and operations for everyday users of the unit. • Read the supplied booklet “Quick Start Guide” before using the unit. EN CONTENTS BEFORE USING THE UNIT 4 6 7 Accessories................................................................................................ 4 Optimizing the speaker settings automatically (YPAO)................ 25 Error messages....................................................................................................................................................................... 27 How to use this manual............................................................................ 4 Warning messages................................................................................................................................................................ 28 Remote control.......................................................................................... 4 PLAYBACK Insert the batteries................................................................................................................................................................... 4 Operating range of the remote control........................................................................................................................... 4 FEATURES Selecting an on-screen menu language.......................................... 24 29 Basic playback procedure...................................................................... 29 5 Enjoying playback................................................................................................................................................................. 29 What you can do with the unit................................................................. 5 Selecting the input source and favorite settings with one touch (SCENE).................................................................................................... 31 Switching information on the front display................................................................................................................. 30 Part names and functions......................................................................... 7 Selecting a registered scene.............................................................................................................................................. 31 Front panel................................................................................................................................................................................. 7 Registering a scene............................................................................................................................................................... 31 Front display (indicators)....................................................................................................................................................... 8 Rear panel................................................................................................................................................................................... 9 Selecting the sound mode..................................................................... 32 Remote control....................................................................................................................................................................... 10 Enjoying sound field effects (CINEMA DSP)................................................................................................................. 33 PREPARATIONS 1 2 Enjoying unprocessed playback...................................................................................................................................... 35 11 Enhancing the bass (Extra Bass)....................................................................................................................................... 36 Playing back digitally compressed formats (such as MP3, etc.) with enriched sound (Compressed Music Enhancer)..................................................................................................................................................................... 36 Placing speakers............................................................................... 12 Typical speaker layouts....................................................................................................................................................... 13 Listening to FM/AM radio....................................................................... 37 Other speaker layouts.......................................................................................................................................................... 14 Setting the frequency steps............................................................................................................................................... 37 Setting the speaker impedance....................................................................................................................................... 15 Selecting a frequency for reception............................................................................................................................... 37 Connecting speakers........................................................................ 16 Registering favorite radio stations (presets)................................................................................................................ 38 Radio Data System tuning.................................................................................................................................................. 41 Connecting speaker cables................................................................................................................................................ 17 3 Connecting the subwoofer (with built-in amplifier)................................................................................................. 17 Playing back music stored on a Bluetooth® device.............................. 42 Connecting a TV/playback devices.................................................. 18 Playback of Bluetooth® device contents....................................................................................................................... 43 Connecting a Bluetooth® device (pairing).................................................................................................................... 42 Input/output jacks and cables.......................................................................................................................................... 18 Enjoying audio using Bluetooth® speakers/headphones....................................................................................... 43 Connecting a TV..................................................................................................................................................................... 19 Playing back music stored on a USB storage device............................ 44 Connecting video devices (such as BD/DVD players).............................................................................................. 20 Connecting a USB storage device................................................................................................................................... 44 Connecting audio devices (such as CD players)......................................................................................................... 22 Playback of USB storage device contents..................................................................................................................... 44 Connecting to the jack on the front panel................................................................................................................... 22 4 Connecting the FM/AM antennas.................................................... 23 5 Connecting the power cable............................................................ 23 2 En Configuring playback settings for different playback sources (Option menu)......................................................................................... 47 Glossary................................................................................................... 77 Option menu items............................................................................................................................................................... 47 HDMI and video information............................................................................................................................................. 78 CONFIGURATIONS Audio information................................................................................................................................................................. 77 Yamaha technologies.......................................................................................................................................................... 78 51 Supported devices and file formats...................................................... 79 Supported devices................................................................................................................................................................ 79 Configuring various functions (Setup Menu)....................................... 51 File formats.............................................................................................................................................................................. 79 Setup menu items................................................................................................................................................................. 52 Video signal flow.................................................................................... 79 Speaker...................................................................................................................................................................................... 54 HDMI........................................................................................................................................................................................... 57 Information on HDMI.............................................................................. 80 Sound......................................................................................................................................................................................... 59 HDMI Control.......................................................................................................................................................................... 80 ECO............................................................................................................................................................................................. 61 Audio Return Channel (ARC)............................................................................................................................................. 82 Function.................................................................................................................................................................................... 62 HDMI signal compatibility.................................................................................................................................................. 82 Bluetooth.................................................................................................................................................................................. 64 Trademarks............................................................................................. 83 Language.................................................................................................................................................................................. 65 Specifications.......................................................................................... 84 Configuring the system settings (ADVANCED SETUP menu).............. 66 ADVANCED SETUP menu items........................................................................................................................................ 66 Changing the speaker impedance setting (SP IMP.)................................................................................................. 66 Selecting the remote control ID (REMOTE ID)............................................................................................................. 67 Changing the FM/AM tuning frequency setting (TU)............................................................................................... 67 Switching the video signal type (TV FORMAT)............................................................................................................ 67 Selecting the HDMI 4K signal format (4K MODE)....................................................................................................... 68 Restoring the default settings (INIT)............................................................................................................................... 68 Updating the firmware (UPDATE).................................................................................................................................... 68 Checking the firmware version (VERSION)................................................................................................................... 68 APPENDIX 69 Frequently asked questions................................................................... 69 Troubleshooting..................................................................................... 70 First, check the following:................................................................................................................................................... 70 Power, system and remote control................................................................................................................................. 70 Audio.......................................................................................................................................................................................... 71 Video.......................................................................................................................................................................................... 73 FM/AM radio............................................................................................................................................................................ 74 USB.............................................................................................................................................................................................. 74 Bluetooth®................................................................................................................................................................................ 75 Error indications on the front display................................................... 76 3 En BEFORE USING THE UNIT Accessories Remote control Check that the following accessories are supplied with the product. The supplied remote control is used as follows. £ AM antenna Insert the batteries £ FM antenna Insert the batteries the right way round. * One of the above is supplied depending on the region of purchase. £ YPAO microphone £ Remote control £ Batteries (AAA, R03, UM-4) (x2) Operating range of the remote control £ CD-ROM (Owner's Manual) £ Quick Start Guide Point the remote control at the remote control sensor on the unit and remain within the operating range shown below. How to use this manual • Some features are not available in certain regions. Within 6 m (20 ft) • Due to product improvements, specifications and appearance are subject to change without notice. 30° • This manual explains operations using the supplied remote control. Notice: Indicates precautions for use to avoid the possibility of malfunction/damage to the unit. Note: Indicates instructions and supplementary explanations for optimum use. 4 En 30° FEATURES What you can do with the unit The unit is equipped with full of useful functions. Supports 2- to 5.1-channel speaker system The ECO mode (power saving function) allows you to create an eco-friendly home theater system You can enjoy your favorite acoustic spaces in various styles. When the ECO mode is enabled, you can reduce the unit's power consumption. • “ECO Mode” (p.61) YPAO automatically optimizes the speaker settings to suit your room. Sequential operation of a TV, AV receiver, and BD/DVD player (HDMI Control) • “Optimizing the speaker settings automatically (YPAO)” (p.25) CINEMA DSP allows you to create stereo or multichannel sounds with the sound fields like actual movie theaters and concert halls in your own room. When the unit is connected to an HDMI Control-compatible TV and BD/DVD player with each HDMI cable, you can control the unit (such as power and volume) and BD/DVD player with TV remote control operations. • “Enjoying sound field effects (CINEMA DSP)” (p.33) • “HDMI Control” (p.80) You can enjoy compressed music with enhanced sound (Compressed Music Enhancer). Supports Bluetooth® devices • “Playing back digitally compressed formats (such as MP3, etc.) with enriched sound (Compressed Music Enhancer)” (p.36) You can play back music stored on a Bluetooth device. Change the input source and favorite settings with one touch (SCENE) • “Playing back music stored on a Bluetooth® device” (p.42) Supports USB storage devices The SCENE function allows you to select the input source and settings registered to the corresponding scene, such as sound program and Compressed Music Enhancer on/off, with just one touch. You can play back music stored on a USB storage device. • “Playing back music stored on a USB storage device” (p.44) • “Selecting the input source and favorite settings with one touch (SCENE)” (p.31) Connecting various devices 4K Ultra HD signal and HDCP 2.2 supported A number of HDMI jacks and various input/output jacks on the unit allow you to connect video devices (such as BD/DVD players), audio devices (such as CD players), game consoles, portable audio player, and other devices. You can enjoy the high definition video quality of 4K with HDCP 2.2 that complies with the latest copyright protection. • “Connecting a TV/playback devices” (p.18) • “Selecting the HDMI 4K signal format (4K MODE)” (p.68) 5 En Playing back TV audio in surround sound with a single HDMI cable connection (Audio Return Channel: ARC) Useful applications The useful application for connections and operations of the unit is as follows. n Application for tablets “AV SETUP GUIDE” When using an ARC-compatible TV, you only need one HDMI cable to enable video output to the TV, audio input from the TV, and the transmission of HDMI Control signals. AV SETUP GUIDE is an application that assists you with cable connections between AV Receiver and source devices as well as AV Receiver setup. This app guides you through the various settings such as speaker connections, TV and source device connections. • “Connecting a TV” (p.19) Surround playback with 5 speakers placed in front Functions: 1) Connection support guide – Speaker connection – TV/source devices connection You can enjoy the surround sound even when the surround speakers are placed in front. • “Enjoying sound field effects without surround speakers (Virtual CINEMA DSP)” (p.34) 2) Setup support guide – Various setup assistance with illustrations. – YPAO setting guidance Enhanced bass reproduction 3) View Owner's Manual Extra Bass allows you to enjoy enhanced bass reproduction that does not depend on the speakers used. • “Enhancing the bass (Extra Bass)” (p.36) * This application is for tablets only. Listening to FM/AM radio For details, search for “AV SETUP GUIDE” on the App Store or Google Play™. The unit is equipped with a built-in FM/AM tuner. You can register up to 40 favorite radio stations as presets. • “Listening to FM/AM radio” (p.37) Easy operation with a TV screen You can operate the USB storage device, view information, or easily configure the settings using the on-screen menu. Auto Rename function The unit creates an input source name, displayed on the front display, automatically according to the connected HDMI-compatible device. • “Input Rename” (p.62) 6 En Part names and functions The part names and functions of the unit and the supplied remote control are as follows. Front panel 1 2 3 4 5 6 7 8 9 0 YPAO MIC INFO MEMORY (PAIRING) PRESET FM AM TUNING VOLUME SCENE BD DVD CD TV RADIO AUX PHONES INPUT TONE CONTROL USB STRAIGHT PROGRAM SILENT CINEMA AUDIO A 1 z (power) key Turns on/off (standby) the unit. 2 Standby indicator Lights up when the unit is in Bluetooth Standby enable condition (p.64). 3 YPAO MIC jack For connecting the supplied YPAO microphone (p.25). 4 Remote control sensor Receives remote control signals (p.4). 5 INFO key Selects the information displayed on the front display (p.30). 6 MEMORY (PAIRING) key Registers FM/AM radio stations as preset stations (p.38). Starts pairing with a Bluetooth device by holding down for 3 seconds (p.42). 7 PRESET keys B CD E F G H I E PROGRAM keys 8 FM and AM keys Switch between FM and AM (p.37). Select a sound program or a surround decoder (p.32). F STRAIGHT key 9 TUNING keys Select the radio frequency (p.37). Enables/disables the straight decode mode (p.35). G AUX jack : Front display For connecting devices, such as portable audio players (p.22). Displays information (p.8). A PHONES jack H USB jack For connecting headphones. For connecting a USB storage device (p.44). B INPUT keys I VOLUME knob Select an input source. Adjusts the volume. C TONE CONTROL key Adjusts the level of high-frequency range (Treble) and lowfrequency range (Bass) individually (p.48). D SCENE keys Select the registered input source and sound program with one touch. Also, turns on the unit when it is in standby mode (p.31). Select a preset FM/AM radio station (p.40). 7 En Front display (indicators) 2 1 5 7 6 STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A - DRC LINK MASTER OUT 4 3 2 ECO VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR 8 9 1 HDMI Lights up when HDMI signals are being input or output. OUT Lights up when HDMI signals are being output. 2 Bluetooth indicator Light up while the unit is connected to a Bluetooth device. 3 CINEMA DSP Lights up when CINEMA DSP (p.33) is working. 4 SLEEP Lights up when the sleep timer is on. 5 STEREO Lights up when the unit is receiving a stereo FM radio signal. TUNED Lights up when the unit is receiving an FM/AM radio station signal. 6 A-DRC 0 A : Information display Displays the current status (such as input name and sound mode name). You can switch the information by pressing INFO (p.30). A ENHANCER Lights up when Compressed Music Enhancer (p.36) is working. B Speaker indicators Indicate speaker terminals from which signals are output. A Front speaker (L) S Front speaker (R) D Center speaker F Surround speaker (L) G Surround speaker (R) L Subwoofer C MUTE Blinks when audio is temporarily muted. Lights up when Adaptive DRC (p.48) is working. 7 Volume indicator Indicates the current volume. 8 ECO Lights up when the eco mode (p.61) is enabled. 9 Cursor indicators Indicate the remote control cursor keys currently operational. 8 En 9 B C Rear panel 2 1 5 ▪ The area around the video/audio output jacks is marked in white on the actual product to prevent improper connections. 6 3 7 4 8 7 SUBWOOFER PRE OUT jack For connecting to a subwoofer (with built-in amplifier) (p.16). 8 SPEAKERS terminals 1 HDMI OUT jack For connecting to an HDMI-compatible TV and outputting video/audio signals (p.18). When using ARC, TV audio signal can also be input through the HDMI OUT jack. 2 HDMI 1–4 jacks For connecting to speakers (p.16). 9 VOLTAGE SELECTOR (Taiwan, Brazil and General models only) Selects the switch position according to your local voltage (p.23). For connecting to HDMI-compatible playback devices and inputting video/audio signals (p.20). 3 ANTENNA jacks For connecting to FM and AM antennas (p.23). 4 Power cable For connecting to an AC wall outlet (p.23). 5 AV jacks AUDIO jacks For connecting to video/audio playback devices and inputting video/audio signals (p.20). 6 MONITOR OUT jacks For connecting to a TV and outputting video signals (p.18). 9 En 9 Remote control 1 1 Remote control signal transmitter 2 BD DVD TV STRAIGHT 5 CD RADIO ENHANCER BASS Pressing this key repeatedly will specify the time (120 min, 90 min, 60 min, 30 min, off), in which the unit switches to the standby mode. PROGRAM 4 SCENE keys Select the registered input source and sound program with one touch. Also, turn on the unit when it is in standby mode (p.31). USB INPUT C OPTION key 3 SLEEP key FM/AM 6 Mutes the audio output. Turns on/off (standby) the unit. SLEEP SCENE 4 B MUTE key 2 z (receiver power) key 3 VOLUME A BLUETOOTH 5 Sound mode keys Select a sound mode (p.32). 6 Input selection keys MUTE 7 B OPTION C 8 RETURN TOP MENU DISPLAY HOME Displays the setup menu (p.51). 8 Menu operation keys ENTER D Cursor keys Select a menu or the parameter. ENTER Confirms a selected item. RETURN Returns to the previous screen. POP-UP/MENU 89: External device operation keys 9 RED GREEN YELLOW BLUE MEMORY 0 Select an input source for playback. 7 SETUP key SETUP TUNING TUNING PRESET A VOLUME keys Adjust the volume. Transmits infrared signals. Let you perform playback operations when “USB” is selected as the input source, or control playback of the HDMI Control-compatible playback device. Note ▪ The playback devices must support HDMI Control. Some HDMI Control-compatible devices cannot be used. ▪ You can assign the unit's functions to the RED/GREEN/ YELLOW/BLUE keys (p.64). : Radio keys Operate the FM/AM radio when “TUNER” is selected as the input source (p.37). MEMORY Registers FM/AM radio stations as presets. PRESET Select a preset station. TUNING Select the radio frequency. 10 En Displays the option menu (p.47). D DISPLAY key Turns on/off the browse screen, playback screen, etc. PREPARATIONS General setup procedure 1 Placing speakers................................................................................................................................ (p.12) 2 Connecting speakers........................................................................................................................ (p.16) 3 Connecting a TV/playback devices.................................................................................................. (p.18) 4 Connecting the FM/AM antennas.................................................................................................... (p.23) 5 Connecting the power cable............................................................................................................ (p.23) 6 Selecting an on-screen menu language.......................................................................................... (p.24) 7 Optimizing the speaker settings automatically (YPAO)................................................................ (p.25) This completes all the preparations. Enjoy playing movies, music, radio and other content with the unit! 11 En 1 Placing speakers Select the speaker layout for the number of speakers that you are using and place the speakers and subwoofer in your room. This section describes the representative speaker layout examples. Notice ▪ (U.S.A. and Canada models only) Under its default settings, the unit is configured for 8-ohm speakers. When connecting 6-ohm speakers, set the unit’s speaker impedance to “6 Ω MIN”. For details, see “Setting the speaker impedance” (p.15). ▪ (Except for U.S.A. and Canada models) Use speakers with an impedance of at least 6 W. ▪ Use a subwoofer with built-in amplifier. ▪ Be sure to connect the front left and right speakers. 12 En Typical speaker layouts n 5.1-channel system n 5.1-channel system (Virtual CINEMA FRONT) We recommend this speaker layout which can maximize the performance of the unit. We recommend this speaker layout when the speakers can't be placed in back of the room. 1 1 2 2 4 9 9 3 4 5 10° to 30° Speaker type Front (L/R) Center Surround (L/R) Subwoofer 5 3 Abbr. 1/2 3 4/5 9 10° to 30° Speaker type Function Produce front left/right channel sounds (stereo sounds). Front (L/R) Produces center channel sounds (such as movie dialogue and vocals). Center Produce surround left/right channel sounds. Surround (L/R) Produces LFE (low-frequency effect) channel sounds and reinforces the bass parts of other channels. Subwoofer This channel is counted as “0.1”. Abbr. 1/2 3 4/5 9 Function Produce front left/right channel sounds (stereo sounds). Produces center channel sounds (such as movie dialogue and vocals). Produce surround left/right channel sounds. By this system, place the surround speakers in front. Produces LFE (low-frequency effect) channel sounds and reinforces the bass parts of other channels. This channel is counted as “0.1”. Note Note ▪ You can enjoy surround sound even without the center speaker (4.1-channel system). ▪ To utilize this configuration, set “Virtual CINEMA FRONT” (p.55) in the “Setup” menu to “On”. ▪ You can place the subwoofer either in the left or right side. ▪ You can enjoy surround sound even without the center speaker (front 4.1-channel system). ▪ You can place the subwoofer either in the left or right side. 13 En Other speaker layouts The following speaker layouts are also available. n 3.1-channel system n 2.1-channel system 1 9 2 1 3 9 14 En 2 Setting the speaker impedance (U.S.A. and Canada models only) Under its default settings, the unit is configured for 8-ohm speakers. When connecting 6-ohm speakers, set the speaker impedance to “6 Ω MIN”. 1 2 Before connecting speakers, connect the power cable to an AC wall outlet. While holding down STRAIGHT on the front panel, press z (power). z (power) STRAIGHT 3 Check that “SP IMP.” is displayed on the front display. LINK MASTER OUT ECO 2 STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC SP IMP.••8¬MIN 4 5 VOL. MUTE VIRTUAL FPR FPL SL SW SR SBL SB SBR Press STRAIGHT to select “6 Ω MIN”. Press z (power) to set the unit to standby mode and remove the power cable from the AC wall outlet. You are now ready to connect the speakers. 15 En 2 Connecting speakers Connect the speakers placed in your room to the unit. The following diagrams provide connections for a 5.1-channel system as an example. For other systems, connect speakers while referring to the connection diagram for the 5.1-channel system. Notice ▪ Remove the unit’s power cable from an AC wall outlet and turn off the subwoofer before connecting the speakers. ▪ The speaker has the polarity (+/-). Connect the speaker cable correctly between the positive (+) terminal of the unit and the speaker, and also between the negative (-) terminal of them. Cables required for connection (commercially available) Speaker cables (x the number of speakers) + – Audio pin cable (x1: for connecting a subwoofer) + – Precaution for connecting of the speaker cables 1 2 1 2 10 mm (3/8”) 3 10 mm (3/8”) 4 3 4 ▪ Prepare speaker cables in a place away from the unit, to avoid accidentally dropping wire strands into the unit's interior which could result in a short circuit or malfunction of the unit. ▪ Improper connecting of the speaker cables may cause short circuit and also damage the unit or the speakers. – Twist the bare wires of the speaker cables firmly together. Audio pin cable – Do not let the bare wires of the speaker cable touch one another. 9 Subwoofer Use a subwoofer with built-in amplifier. – Do not let the bare wires of the speaker cable come into contact with the unit’s metal parts (rear panel and screws). ▪ If “Check SP Wires” appear on the front display when the unit is turned on, turn off the unit, and then check the speaker cables short circuit. 5 4 3 2 1 Surround (R) Surround (L) Center Front (R) Front (L) 16 En n Connecting center/surround speakers Connecting speaker cables 1 Speaker cables have two wires. One is for connecting the negative (-) terminals of the unit and the speaker to each other, and the other is for the positive (+) terminals. If the wires are colored to prevent confusion, connect the black wire to the negative and the other wire to the positive terminal. 2 3 4 n Connecting front speakers 1 2 3 4 Remove approximately 10 mm (3/8”) of insulation from the ends of the speaker cable, and twist the bare wires of the cable firmly together. Press down the tab. Insert the bare wires of the cable into the hole in the terminal. Release the tab. SU RR OU ND Loosen the speaker terminal. a Insert the bare wires of the cable into the gap on the side (upper right or bottom left) of the terminal. Tighten the terminal. + (red) b b + (red) - (black) Use an audio pin cable to connect the subwoofer. a - (black) Audio pin cable Using a banana plug (U.S.A., Canada, Taiwan, Brazil and General models only) Tighten the speaker terminal. Insert a banana plug into the end of the terminal. a TE R d Connecting the subwoofer (with built-in amplifier) FR ON T d CE N c c 1 2 Remove approximately 10 mm (3/8”) of insulation from the ends of the speaker cable, and twist the bare wires of the cable firmly together. FR ON T Banana plug b 17 En 3 Connecting a TV/playback devices The unit is equipped with a variety of input jacks including HDMI input jacks to allow you to connect different types of playback devices. For information on how to connect a Bluetooth device or a USB storage device, see the following pages. • Connecting a Bluetooth device (p.42) • Connecting a USB storage device (p.44) n Video jacks HDMI jacks Transmit digital video and digital sound through a single jack. Use an HDMI cable. HDMI cable Transmit analog video signals. Use a video pin cable. ▪ The unit’s HDMI jacks support the HDMI Control, Audio Return Channel (ARC), and 3D and 4K Ultra HD video transmission (through output) features. ▪ Use a Premium High Speed HDMI Cable or Premium High Speed Cable with Ethernet to enjoy 3D or 4K Ultra HD videos. Transmit analog stereo audio signals. Use a stereo pin cable (RCA cable). Stereo pin cable Video pin cable n Audio jacks (Stereo mini jack) Transmits analog stereo audio signals. Use a stereo mini-plug cable. OPTICAL jack Transmit digital audio signals. Use a digital optical cable. If there is a protective cap on the tip of the cable, remove it before using the cable. Digital optical cable Note ▪ Use a 19-pin HDMI cable with the HDMI logo. We recommend using a cable less than 5.0 m (16.4 ft) long to prevent signal quality degradation. (Stereo L/R jacks) VIDEO jacks Input/output jacks and cables n Video/audio jacks AUDIO jacks OPTICAL COAXIAL jacks Transmit digital audio signals. Use a digital coaxial cable. Digital coaxial cable 18 En Stereo mini-plug cable Connecting a TV n Composite video connection Connect a TV to the unit so that video input to the unit can be output to the TV. You can also enjoy playback of TV audio on the unit. When connecting any video device with a video pin cable, connect the TV to the MONITOR OUT (VIDEO) jack. To maximize the performance of the unit, we recommend connecting a TV with an HDMI cable. Note n HDMI connection ▪ Operations with TV screen are available only when your TV is connected to the unit via HDMI. ▪ If you connect your TV to the unit with a cable other than HDMI, video input to the unit via HDMI cannot be output to the TV. ▪ If you will receive TV broadcasts only from the set-top box, you do not need to make an audio cable connection between the TV and the unit. Connect the TV to the unit with an HDMI cable and a digital optical cable. The unit (rear) HDMI OUT jack VIDEO (composite video) connection HDMI input Connect the TV to the unit with a video pin cable and a digital optical cable. HDMI HDMI HDMI The unit (rear) Video input (composite video) MONITOR OUT (VIDEO) jack MONITOR OUT VIDEO OPTICAL O V V O OPTICAL TV AUDIO 1 (OPTICAL) jack Audio output (digital optical) OPTICAL O Note O TV ▪ A digital optical cable connection allows audio from the TV to be played back on the unit. A digital optical cable connection is not needed in the following cases: AUDIO 1 (OPTICAL) jack – If your TV supports Audio Return Channel (ARC) – If you will receive TV broadcasts only from the set-top box ▪ If you connect a TV that supports HDMI Control to the unit with an HDMI cable, you can control the unit’s power and volume with the TV’s remote control. To use HDMI Control and ARC, you need to configure the HDMI settings on the unit. For details on the settings, see “Information on HDMI” (p.80). About Audio Return Channel (ARC) ▪ ARC allows audio signals to travel both ways. If you connect a TV that supports ARC to the unit with a single HDMI cable, you can output video/audio to the TV or input TV audio to the unit. ▪ When using ARC, connect a TV with an HDMI cable that supports ARC. 19 En Audio output (digital optical) Connecting video devices (such as BD/DVD players) n Composite video connection Connect video devices such as BD/DVD players, set-top boxes (STBs) and game consoles to the unit. Depending on the video/audio output jacks available on your video device, choose one of the following connections. We recommend using an HDMI connection if the video device has an HDMI output jack. Connect a video device to the unit with a video pin cable and an audio cable (digital coaxial or stereo pin cable). Choose a set of input jacks (on the unit) depending on the audio output jacks available on your video device. Output jacks on video device Video Note If the combination of video/audio input jacks available on the unit does not match your video device, change its combination according to the output jacks of your device (p.21). Input jacks on the unit Audio Digital coaxial Composite video n HDMI connection AV 1 (VIDEO + COAXIAL) Analog stereo AV 2–3 (VIDEO + AUDIO) Digital optical You need to change the combination of video/audio input jacks (p.21). Connect a video device to the unit with an HDMI cable. Video output (composite video) AV 1–3 (VIDEO) jacks HDMI 1–4 jacks The unit (rear) VIDEO VIDEO V V The unit (rear) HDMI OUT jack HDMI Video device COAXIAL HDMI C C COAXIAL HDMI L L L L R R R R Video device AV 1 (COAXIAL) jack or AV 2–3 (AUDIO) jacks If you select HDMI 1–4 as the input source by pressing INPUT, the video/audio played back on the video device will be output from the unit. Audio output (digital coaxial or analog stereo) If you select AV 1-3 as the input source by pressing INPUT, the video/audio played back on the video device will be output from the unit. Note To watch videos input to the HDMI 1–4 jacks, you need to connect your TV to the HDMI OUT jack of the unit (p.19). Note To watch videos input to the AV 1–3 (VIDEO) jacks, you need to connect your TV to the MONITOR OUT (VIDEO) jack of the unit (p.19). 20 En n Changing the combination of video/audio input jacks 3 If the combination of video/audio input jacks available on the unit does not match your video device, change its combination according to the output jacks of your device. You can connect a video device that has the following video/audio output jacks. Output jacks on video device Press OPTION. SLEEP SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS MUTE OPTION PROGRAM FM/AM Input jacks on the unit SETUPP USB INPUT OPTION VOLUME BLUETOOTH Video HDMI Composite video Audio Video Audio Digital optical HDMI 1–4 AUDIO 1 (OPTICAL) Digital coaxial HDMI 1–4 AUDIO 2 (COAXIAL) AV 1 (COAXIAL) Analog stereo HDMI 1–4 AV 2–3 (AUDIO) Digital optical AV 1–3 (VIDEO) AUDIO 1 (OPTICAL) MUTE SETUP RETURN POP-UP/MENU RETURN RED GREEN YELLOW TUNING TOP MENU HOME POP-UP/MENU PRESET 4 Use the cursor keys (q/w) to select “Audio In” and press ENTER. LINK MASTER 2 ECO Video output (composite video) STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC VOL. MUTE VIRTUAL Audio In 5 VIDEO V FPR FPL SL SW SR SBL SB SBR Use the cursor keys (e/r) to select “AUDIO 1” (audio input jack to be used). LINK MASTER OUT 2 ECO STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC Audio•••AUDIO1 Set-top box 6 OPTICAL O DISPLAYY DISPLA BLUE MEMORY OUT V HOME TUNING For example, if you have connected a video device to AV 2 (VIDEO) and AUDIO 1 (OPTICAL) jack of the unit, change the combination setting as follows. AV 2 (VIDEO) jack ENTER DISPLAY TOP MENU Necessary setting The unit (rear) Cursor keys ENTER OPTION ENTER O VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR Press OPTION. This completes the necessary settings. AUDIO 1 (OPTICAL) jack 1 2 If you select “AV 2” as the input source by pressing INPUT, the video/audio played back on the video device will be output from the unit. Audio output (digital optical) After connecting external devices (such as a TV and playback devices) and power cable of the unit, turn on the unit. Press INPUT to select “AV 2” (video input jack to be used) as the input source. 21 En Connecting audio devices (such as CD players) Connecting to the jack on the front panel Connect audio devices such as CD players and MD players to the unit. Depending on the audio output jacks available on your audio device, choose one of the following connections. Use the AUX jack on the front panel to temporarily connect devices such as portable audio players to the unit. Audio output jacks on audio device Before making a connection, stop playback on the device and turn down the volume on the unit. Audio input jacks on the unit Digital optical AUDIO 1 (OPTICAL) Digital coaxial AUDIO 2 (COAXIAL) AV 1 (COAXIAL) Analog stereo AV 2–3 (AUDIO) BD DVD CD TV RADIO AUX INPUT TONE CONTROL PROGRAM USB STRAIGHT AUDIO The unit (rear) The unit (front) OPTICAL (TV) O O OPTICAL COAXIAL C C COAXIAL L L L Audio device Portable audio player L R If you select “AUX” as the input source by pressing INPUT, the audio played back on the device will be output from the unit. R R AV 1–3 jacks AUDIO 1–2 jacks R Note Audio output (either digital optical, digital coaxial, or analog stereo) ▪ You need to prepare the audio cable that matches the output jacks on your device. ▪ For details on how to connect a USB storage device, see “Connecting a USB storage device” (p.44). If you select AV 1-3 or AUDIO 1-2 as the input source by pressing INPUT, the audio played back on the audio device will be output from the unit. 22 En 4 Connecting the FM/AM antennas 5 Connecting the power cable Connect the supplied FM/AM antennas to the unit. Warning Fix the end of the FM antenna to a wall, and place the AM antenna on a flat surface. (Taiwan, Brazil and General models only) Make sure you set VOLTAGE SELECTOR of the unit BEFORE plugging the power cable into an AC wall outlet. Improper setting of VOLTAGE SELECTOR may cause damage to the unit and create a potential fire hazard. FM antenna AM antenna Before connecting the power cable Set the switch position of VOLTAGE SELECTOR according to your local voltage. Voltages are AC 110– 120/220–240 V, 50/60 Hz. The unit (rear) VOLTAGE SELECTOR VOLTAGE SELECTOR 110V– 120V 220V– 240V The unit (rear) Assembling and connecting the AM antenna After all the connections are complete, plug in the power cable. The unit (rear) To an AC wall outlet Hold down Insert Release Note ▪ Unwind only the length of cable needed from the AM antenna unit. ▪ The wires of the AM antenna have no polarity. 23 En 6 Selecting an on-screen menu language Select the desired on-screen menu language. 1 2 6 Press z (receiver power) to turn on the unit. Note The information on the front display is provided in English only. Turn on the TV and switch the TV input to display video from the unit (HDMI OUT jack). Note Operations with TV screen are available only when your TV is connected to the unit via HDMI. If not, carry out operations while viewing the front display. 3 4 5 To exit from the menu, press SETUP. Press SETUP. Use the cursor keys to select “Language” and press ENTER. Use the cursor keys to select the desired language. 24 En 7 Optimizing the speaker settings automatically (YPAO) The Yamaha Parametric room Acoustic Optimizer (YPAO) function detects speaker connections, measures the distances from them to your listening position(s), and then automatically optimizes the speaker settings, such as volume balance and acoustic parameters, to suit your room. 4 Place the YPAO microphone at your listening position and connect it to the YPAO MIC jack on the front panel. Note Note ▪ When you use the front 5.1-channel speaker (Virtual CINEMA FRONT) configuration (p.13), set “Virtual CINEMA FRONT” (p.55) in the “Setup” menu to “On” beforehand. Place the YPAO microphone at your listening position (same height as your ears). We recommend the use of a tripod as a microphone stand. You can use the tripod screws to stabilize the microphone. ▪ Please note the following when using YPAO. The unit (front) – Use YPAO after connecting a TV and speakers to the unit. – During the measuring process, test tones are output at high volume. Ensure that the test tones do not frighten small children. – During the measuring process, you cannot adjust the volume. – During the measuring process, keep the room as quiet as possible. – Do not connect headphones. 1 – Do not stand between the speakers and the YPAO microphone during the measurement process (about 3 minutes). 1 2 9 Press z (receiver power) to turn on the unit. Turn on the TV and switch the TV input to display video from the unit (HDMI OUT jack). 2 3 4 5 Note Operations with TV screen are available only when your TV is connected to the unit via HDMI. If not, carry out operations while viewing the front display. 3 Ear height Turn on the subwoofer and set the volume to half. If the crossover frequency is adjustable, set it to maximum. VOLUME MIN MAX CROSSOVER/ HIGH CUT MIN The following screen appears on the TV. 9 MAX 25 En 5 7 To start the measurement, use the cursor keys to select “Start” and press ENTER. Use the cursor keys (e/r) to select “SAVE” and press ENTER. The measurement will start in 10 seconds. Press ENTER to start the measurement immediately. Note To stop the measurement temporarily, press RETURN and follow the procedure in “Error messages” (p.27). The adjusted speaker settings are applied. The following screen appears on the TV when the measurement finishes. Note To finish the measurement without saving the result, select “CANCEL”. 8 1 Disconnect the YPAO microphone from the unit. This completes optimization of the speaker settings. 2 Notice 3 ▪ The YPAO microphone is sensitive to heat, so should not be placed anywhere where it could be exposed to direct sunlight or high temperatures (such as on top of AV equipment). 4 1 The number of speakers (front side/rear side/subwoofer) 2 Speaker distance (nearest/farthest) 3 Adjustment range of speaker output level 4 Warning message (if available) Note ▪ If any error message (such as E-1) or warning message (such as W-1) appears, see “Error messages” (p.27) or “Warning messages” (p.28). ▪ A speaker with a problem is indicated by blinking of the speaker indicators in the front display. ▪ If multiple warnings are given (when operating with the front display), use the cursor keys (q/w) to check the other warning messages. 6 Confirm the results displayed on the screen and press ENTER. 26 En Error messages If any error message is displayed during the measurement, resolve the problem and perform YPAO again. Error message Cause E-1:No Front SP Front speakers are not detected. (E-1:NO FRNT SP) E-2:No Sur. SP (E-2:NO SUR SP) E-5:Noisy Error message (E-5:NOISY) E-7:No MIC (E-7:NO MIC) E-8:No Signal TV screen (E-8:NO SIGNAL) 2 ECO E-5:NOISY E-9:User Cancel Front display (E-9:CANCEL) n Procedure to handle errors E-10:Internal Err. 1 2 Keep the room quiet and retry YPAO. If you select “PROCEED”, YPAO takes the measurement again and ignores any noise detected. The YPAO microphone has been removed. Connect the YPAO microphone to the YPAO MIC jack firmly and retry YPAO. The YPAO microphone cannot detect test tones. Connect the YPAO microphone to the YPAO MIC jack firmly and retry YPAO. If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or service center. VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR (E-10:INTERNAL) Check the content of error message and press ENTER. Select “EXIT” and press ENTER. Use the cursor keys (q/w) to select “Exit” and press ENTER. Disconnect the YPAO microphone from the unit. To retry the YPAO measurement from beginning: 1 Select “RETRY” and press ENTER. To proceed with the current YPAO measurement (for E-5 and E-9 only): 1 An internal error has occurred. Texts in parentheses denote indicators on the front display. To exit the YPAO measurement: 1 2 3 The measurement has been Retry or exit YPAO as necessary. canceled. Note Use the cursor keys (e/r) to select the desired operation. Select “PROCEED” and press ENTER. 27 En Exit YPAO, turn off the unit, and then check the speaker connections. The noise is too loud. STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC LINK MASTER OUT One of the surround speakers cannot be detected. Remedy Exit YPAO, and turn off and on the unit. If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or service center. Warning messages If a warning message is displayed after the measurement, you can still save the measurement results by following on-screen instructions. Warning message Cause Remedy Check the cable connections (+/-) of the problem speaker. However, we recommend you perform YPAO again in order to use the unit with the optimal speaker settings. If the speaker is connected incorrectly: W-1:Out of Phase (W-1:PHASE) A speaker cable may be connected with the reverse polarity (+/-). Turn off the unit, reconnect the speaker cable. If the speaker is connected correctly: Depending on the type of speakers or room environment, this message may appear even if the speakers are connected correctly. In this case, you can ignore the message. W-2:Over Distance (W-2:DISTANCE) Warning message TV screen Problem speaker (blinks) OUT W-3:Level Error STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC LINK MASTER 2 ECO W-1:PHASE (W-3:LEVEL) VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR Front display n Procedure to handle warnings 1 2 Texts in parentheses denote indicators on the front display. Use the cursor keys (e/r) to select the desired operation. To save the measurement results: Select “SAVE” and press ENTER. To discard the measurement result: 1 3 Select “CANCEL” and press ENTER. Disconnect the YPAO microphone from the unit. 28 En Exit YPAO, turn off the unit, and place the problem speaker within 24 m (80 ft) of the listening position. Check the usage environment and cable connections (+/-) of each speaker, and the volume of the subwoofer. If there is There are significant volume any problem, exit YPAO, turn off the unit, differences between the and then reconnect speaker cable or speakers. correct the speaker positions. We recommend using the same speakers or speakers with specifications that are as similar as possible. Note Check the content of warning message and press ENTER. 1 A speaker is placed more than 24 m (80 ft) from the listening position. PLAYBACK Basic playback procedure Enjoying playback 1 2 3 Start playback on the external device or select a radio station. Refer to the instruction manual for the external device. Turn on the external devices (such as a TV or BD/DVD player) connected to the unit. For details on the following operations, see the corresponding pages. ▪ “Listening to FM/AM radio” (p.37) ▪ “Playing back music stored on a Bluetooth® device” (p.42) Use the input selection keys to select an input source. ▪ “Playing back music stored on a USB storage device” (p.44) SLEEP 4 SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS PROGRAM PROGRAM FM/AM Input selection keys USB INPUT BLUETOOTH FM/AM MUTE SETUP INPUT ENTER RETURN TOP MENU RED DISPLAY HOME GREEN YELLOW ▪ To mute the audio output, press MUTE. Press MUTE again to unmute. USB OPTION VOLUME ▪ To adjust the treble/bass settings, use the “Option” menu or TONE CONTROL on the front panel (p.48). VOLUME BLUETOOTH POP-UP/MENU BLUE MEMORY TUNING TUNING PRESET Press VOLUME to adjust the volume. Note VOLUME MUTE MUTE 29 En Switching information on the front display 1 Currently input source AV Press INFO repeatedly to select between the various display items. OUT AUDIO AUX 2 ECO Audio Decoder VOL. MUTE VIRTUAL USB FPL FPR SL SW SR SBL SB SBR Item name OUT TUNER STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC 2 ECO DPL Song (song title), Artist (artist name), Album (album name), DSP Program (sound mode name), Audio Decoder (decoder name*) Frequency (frequency), DSP Program (sound mode name), Audio Decoder (decoder name*) About 3 seconds after a display item is selected, its corresponding information appears. LINK MASTER Input (input source name), DSP Program (sound mode name), Audio Decoder (decoder name*) Bluetooth STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC LINK MASTER Item HDMI (U.K. and Europe models only) Radio Data System data is also available when the unit is tuned into a Radio Data System broadcasting station (p.41). VOL. MUTE VIRTUAL * The name of the audio decoder currently activated is displayed. If no audio decoder is activated, “Decoder Off” appears. FPL FPR SL SW SR SBL SB SBR Information Note Available items vary depending on the selected input source. The displayed item can also be applied separately to each input source. 30 En Selecting the input source and favorite settings with one touch (SCENE) The SCENE function allows you to select the assigned input source, sound program, and Compressed Music Enhancer on/off with just one touch. Registering a scene 1 Selecting a registered scene 1 ▪ Select an input source (p.29) Press SCENE. ▪ Select a sound program (p.32) or straight decode (p.35) The input source and settings registered to the corresponding scene are selected. The unit turns on automatically when it is in standby mode. ▪ Enable/disable Compressed Music Enhancer (p.36) 2 SLEEP SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS Perform the following operations to prepare the settings you want to assign to a scene. Hold down the desired SCENE key until “SET Complete” appears on the front display. PROGRAM LINK MASTER FM/AM OUT USB INPUT VOLUME SLEEP MUTE SCENE ECO SETUP BD DVD OPTION TV CD RADIO ENHANCER BASS SCENE ENTER RETURN TOP MENU RED STRAIGHT DISPLAY HOME GREEN YELLOW POP-UP/MENU BLUE PROGRAM MEMORY TUNING TUNING PRESET By default, the following settings are registered for each scene. SCENE Input HDMI1 AUDIO1 2 STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC SET Complete BLUETOOTH AUDIO2 TUNER Sound program MOVIE (Sci-Fi) STRAIGHT STRAIGHT STEREO (5ch Stereo) Compressed Music Enhancer Off On Off On SCENE link playback On On Off Off Note The SCENE link playback function allows you to automatically turn on the TV or start playback of an external device connected to the unit via HDMI, in conjunction with a scene selection. To enable SCENE link playback, set “SCENE” (p.58) in the “Setup” menu to “On”. 31 En VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR Selecting the sound mode I want to enjoy listening to compressed music. The unit is equipped with a variety of sound programs and surround decoders that allow you to enjoy playback sources with your favorite sound mode (such as sound field effect or stereo playback). • Enable Compressed Music Enhancer by pressing ENHANCER (p.36). This mode lets you enjoy listening to compressed music from Bluetooth devices, USB devices, etc. as it gives the music additional depth and breadth (p.36). SLEEP SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS Note PROGRAM ▪ The sound mode can be applied separately to each input source. FM/AM USB INPUT VOLUME SLEEP MUTE SCENE BLUETOOTH SETUP OPTION BD DVD TV CD RADIO ENHANCER BASS ▪ When you play back audio signals with a sampling rate of higher than 96 kHz, the straight decode mode (p.35) is automatically selected. ▪ You can check which speakers are currently outputting sound by looking at the speaker indicators on the unit’s front panel (p.8). ENTER RETURN TOP MENU RED DISPLAY HOME GREEN YELLOW BLUE MEMORY TUNING STRAIGHT POP-UP/MENU PROGRAM TUNING PRESET STRAIGHT ENHANCER BASS PROGRAM I want to enjoy viewing video sources such as movies, TV programs, or games. • Select a sound program suitable for each video source by pressing PROGRAM repeatedly (p.33). I want to enjoy listening to music sources or stereo playback. • Select a sound program suitable for music or stereo playback by pressing PROGRAM repeatedly (p.34). I want to enjoy multichannel playback from 2-channel sources. • Select a surround decoder in the “Option” menu (p.47). I want to enjoy unprocessed sounds in original channels. • Switch to the straight decode mode by pressing STRAIGHT (p.35). I want to enjoy enhanced bass sounds. • Enable Extra Bass by pressing BASS (p.36). 32 En Enjoying sound field effects (CINEMA DSP) Drama This program features stable reverberations that match a wide range of movie genres, from serious dramas to musicals and comedies. The reverberations are modest, but suitably stereophonic. The sound effects and background music are reproduced with a gentle echo that does not impinge on the articulation of the dialogue. You’ll never get tired listening for long periods. Mono Movie This program reproduces monaural video sources, such as classic movies, in an atmosphere of a good old movie theater. The program creates a pleasant space with depth, by adding breadth and the appropriate reverberation to the original audio. Sports This program allows listeners to enjoy the rich vividness of sport broadcasts and light entertainment programs. In sports broadcasts, the commentators’ voices are positioned clearly at the center, while the atmosphere inside the stadium is realistically conveyed by the peripheral delivery of the sounds of the fans in a suitable space. Action Game This program is suitable for action games, such as car racing and fighting games. The reality of, and emphasis on, various effects makes the player feel like they are right in the middle of the action, allowing for greater concentration. Use this program in combination with Compressed Music Enhancer for a more dynamic and strong sound field. Roleplaying Game This program is suitable for role-playing and adventure games. This program adds depth to the sound field for natural and realistic reproduction of background music, special effects, and dialogue from a wide variety of scenes. Use this program in combination with Compressed Music Enhancer for a clearer and more spatial sound field. The unit is equipped with a variety of sound programs that utilize Yamaha’s original DSP technology (CINEMA DSP). It allows you to easily create sound fields like actual movie theaters or concert halls in your room. Sound program category “CINEMA DSP” lights up LINK MASTER OUT 2 ECO STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC Sci-Fi VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR Sound program Note You can adjust the sound field effect level in “DSP Level (DSP Level)” (p.48) in the “Option” menu. n Sound programs suitable for movies (MOVIE) The following sound programs are optimized for viewing video sources, such as movies, TV programs, and games. Standard This program creates a sound field that emphasizes the surround feeling without disturbing the original acoustic positioning of multichannel audio, such as Dolby Digital and DTS. Its design is based on the concept of the ideal movie theater, in which the audience is surrounded by beautiful reverberations from the left, right, and rear. Spectacle This program delivers the scale and grandeur of spectacular movie productions. It delivers an expansive sound space to match the cinemascope wide-screen, and boasts a broad dynamic range, providing everything from small delicate sounds to powerful loud booms. Sci-Fi This program clearly reproduces the finely elaborated sound design of the latest Sci-Fi and SFX movies. You can enjoy a variety of cinematographically created virtual spaces reproduced with clear separation between dialogue, sound effects, and background music. Adventure This program is ideal for reproducing the sound design of action and adventure movies precisely. The sound field restrains reverberations, but puts emphasis on reproducing a sensation of expansiveness on both sides, powerful space expanded widely to the left and right. The restrained depth creates a clear and powerful space, while also maintaining the articulation of the sounds and the separation of the channels. 33 En n Sound programs suitable for music (MUSIC) n Sound programs suitable for stereo playback (STEREO) The following sound programs are optimized for listening to music sources. You can select stereo playback. Hall in Munich This program simulates a Munich concert hall with approximately 2,500 seats that uses stylish wood for the interior finishing. Fine, beautiful reverberations spread richly, creating a calming atmosphere. The listener’s virtual seat is at the center left of the arena. Hall in Vienna This program simulates a 1700-seat, middle-sized concert hall with a shoebox shape that is traditional in Vienna. Pillars and ornate carvings create extremely complex reverberations from all around the audience, producing a very full, rich sound. Chamber This program creates a relatively wide space with a high ceiling, like an audience hall in a palace. It offers pleasant reverberations that are suitable for courtly music and chamber music. Cellar Club This program simulates an intimate concert venue with a low ceiling and homey atmosphere. A realistic, live sound field delivers powerful sounds that make you feel as if you are sitting in the front row in front of a small stage. The Roxy Theatre This program creates the sound field of a 460-seat rock music concert venue in Los Angeles. The listener’s virtual seat is at the center left of the hall. The Bottom Line This program creates the sound field at stage front in The Bottom Line, a famous New York jazz club once. The floor can seat 300 people to the left and right in a sound field offering real and vibrant sound. Music Video 2ch Stereo Use this program to mix down multichannel sources to 2 channels. When multichannel signals are input, they are down mixed to 2 channels and output from the front speakers (this program does not utilize CINEMA DSP). 5ch Stereo Use this program to output sound from all speakers. When you play back multichannel sources, the unit mixes down the source to 2 channels, and then outputs the sound from all speakers. This program creates a larger sound field and is ideal for background music at parties. n Enjoying sound field effects without surround speakers (Virtual CINEMA DSP) If you select one of the sound programs (except 2ch Stereo and 5ch Stereo) when no surround speakers are connected, the unit automatically creates the surround sound field using the front-side speakers. n Enjoying surround sound with 5 speakers placed in front (Virtual CINEMA FRONT) You can enjoy the surround sound even when the surround speakers are placed in front. This program allows you to enjoy videos of pop, rock, and jazz concerts, as if you were there yourself. Immerse yourself in the hot concert atmosphere thanks to the vividness of the singers and solos on stage, a presence sound field that emphasizes the beat of rhythm instruments, and a surround sound field that reproduces the space of a big live hall. n Enjoying surround sound with headphones (SILENT CINEMA) You can enjoy surround or sound field effects, like a multichannel speaker system, with stereo headphones by connecting the headphones to the PHONES jack and selecting a sound program or a surround decoder. 34 En n Playing back 2-channel sources in multichannel Enjoying unprocessed playback (surround decoder) You can play back input sources without any sound field effect processing. The surround decoder enables unprocessed multichannel playback from 2-channel sources. When a multichannel source is input, it works the same way as the straight decode mode. n Playing back in original channels (straight decode) When the straight decode mode is enabled, the unit produces stereo sound from the front speakers for 2-channel sources such as CDs, and produces unprocessed multichannel sounds for multichannel sources. 1 For details on each decoder see “Glossary” (p.77). 1 Press STRAIGHT. Press PROGRAM repeatedly to select a surround decoder. The previously selected surround decoder is selected. You can change the surround decoder in “Sur.Decode” (p.47) in the “Option” menu. Each time you press the key, the straight decode mode is enabled or disabled. SLEEP SCENE BD DVD LINK MASTER OUT ECO 2 STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC STRAIGHT TV STRAIGHT CD RADIO ENHANCER BASS PROGRAM VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR FM/AM USB INPUT VOLUME SLEEP MUTE SCENE BLUETOOTH SETUP BD DVD OPTION TV CD RADIO ENHANCER BASS ENTER RETURN STRAIGHT DISPLAY TOP MENU RED POP-UP/MENU HOME GREEN YELLOW BLUE PROGRAM MEMORY TUNING PROGRAM TUNING PRESET “SUR. DECODE” appears STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC LINK MASTER OUT 2 ECO DPL VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR DPL Uses the Dolby Pro Logic decoder suitable for all sources. DPL Movie Uses the Dolby Pro Logic II decoder suitable for movies. DPL Music Uses the Dolby Pro Logic II decoder suitable for music. DPL Game Uses the Dolby Pro Logic II decoder suitable for games. Neo:6 Cinema Uses the DTS Neo: 6 decoder suitable for movies. Neo:6 Music Uses the DTS Neo: 6 decoder suitable for music. Note You can adjust the surround decoder parameters in “DSP Parameter” (p.59) in the “Setup” menu. 35 En Enhancing the bass (Extra Bass) Playing back digitally compressed formats (such as MP3, etc.) with enriched sound (Compressed Music Enhancer) Extra Bass allows you to enjoy enhanced bass sounds, regardless of the size of the front speakers and the presence or absence of the subwoofer. 1 Press BASS. Each time you press the key, Extra Bass is enabled or disabled. Compressed Music Enhancer adds depth and breadth to the sound, allowing you to enjoy a dynamic sound close to the original sound before it was compressed. This function can be used along with any other sound modes. Note You can also use “Extra Bass” (p.55) in the “Setup” menu to enable/disable Extra Bass. 1 Press ENHANCER. Each time you press the key, Compressed Music Enhancer is enabled or disabled. “ENHANCER” lights up LINK MASTER OUT 2 ECO STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC Enhancer On VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR Note ▪ Compressed Music Enhancer does not work on the following audio sources. – Signals whose sampling frequency is over 48 kHz – High-definition streaming audio ▪ You can also use “Enhancer (Enhancer)” (p.48) in the “Option” menu to enable/disable Compressed Music Enhancer. 36 En Listening to FM/AM radio You can tune into a radio station by specifying its frequency or selecting from registered radio stations. 4 5 Note ▪ The radio frequencies differ depending on the country or region where the unit is being used. The explanation of this section uses a display with frequencies used in U.K. and Europe models. ▪ If you cannot obtain good reception on the radio, adjust the direction of the FM/AM antennas. Press STRAIGHT to select “FM100/AM10”. Press z (power) to set the unit to standby mode and turn it on again. Selecting a frequency for reception Setting the frequency steps 1 (Asia, Taiwan, Brazil and General models only) At the factory, the frequency step setting is set to 50 kHz for FM and 9 kHz for AM. Depending on your country or region, set the frequency steps to 100 kHz for FM and 10 kHz for AM. Press FM/AM to select a band. “TUNER” is selected as the input source and then the frequency currently selected is displayed. LINK MASTER OUT 1 2 ECO When holding down STRAIGHT on the front panel, press z (power). z (power) 3 STRAIGHT Press PROGRAM repeatedly to select “TU”. LINK MASTER OUT ECO 2 STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC TU••••FM50/AM9 STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC FM 87.50MHz Set the unit to standby mode. PROGRAM 2 VOL. MUTE VIRTUAL FPR FPL SL SW SR SBL SB SBR 37 En VOL. MUTE VIRTUAL 2 Registering favorite radio stations (presets) Press TUNING repeatedly to set a frequency. You can register up to 40 radio stations as presets. Once you have registered stations, you can easily tune into them by selecting their preset numbers. Hold down the key for about a second to search stations automatically. SLEEP SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS n Registering radio stations automatically (Auto Preset) PROGRAM FM/AM USB INPUT VOLUME RED GREEN YELLOW LO Automatically register FM radio stations with strong signals (up to 40 stations). BLUE BLUETOOTH TUNING MEMORY MUTE SETUP Note OPTION TUNING ENTER RETURN TUNING ▪ To register AM radio stations, follow “Registering a radio station manually” (p.39). DISPLAY TOP MENU HOME ▪ (U.K. and Europe models only) Only Radio Data System broadcasting stations are registered automatically by the Auto Preset function. POP-UP/MENU PRESET RED GREEN YELLOW BLUE MEMORY TUNING TUNING PRESET LINK MASTER OUT 2 ECO 1 2 3 STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC FM 98.50MHz VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR “TUNED” lights up when the unit is receiving an FM/AM radio station signal. Press FM/AM to select “TUNER” as the input source. Press OPTION. Use the cursor keys to select “Preset” and press ENTER. LINK MASTER OUT “STEREO” lights up when the unit is receiving a stereo FM radio signal. 2 ECO Preset Note ▪ You can switch between “Stereo” (stereo) and “Mono” (monaural) for FM radio reception by selecting “FM Mode” in the “Option” menu. When the signal reception for an FM radio station is unstable, switching to monaural may improve it. ▪ You can watch videos input from external devices while listening to radio by selecting the video input jack in “Video Out (Video Out)” (p.50) in the “Option” menu. 38 En STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC VOL. MUTE VIRTUAL FPR FPL SL SW SR SBL SB SBR 4 n Registering a radio station manually To start the Auto Preset process, press ENTER. Select a radio station manually and register it to a preset number. “SEARCH” appears during Auto Preset OUT 1 STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC LINK MASTER 2 ECO 01:FM 87.50MHz VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR 2 Preset number from which to start the registration Follow “Selecting a frequency for reception” (p.37) to tune into the desired radio station. Hold down MEMORY for a few seconds. The first time that you do register a station, the selected radio station will be registered to the preset number “01”. Thereafter, each radio station you select will be registered to the next empty (unused) preset number after the most recently registered number. Note ▪ To specify the preset number from which to start the registration, press cursor keys (e/r) or PRESET to select a preset number. ▪ To cancel the Auto Preset process, press RETURN. When the Auto Preset process finishes, “FINISH” appears and the “Option” menu closes automatically. SLEEP SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS PROGRAM LINK MASTER OUT ECO 2 STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC Auto Preset FM/AM USB INPUT VOL. MUTE VIRTUAL VOLUME RED GREEN YELLOW LO BLUE BLUETOOTH FPR FPL SL SW SR SBL SB SBR MEMORY MEMORY MUTE SETUP OPTION TUNING ENTER RETURN TUNING DISPLAY TOP MENU HOME POP-UP/MENU PRESET RED GREEN YELLOW BLUE MEMORY TUNING TUNING PRESET LINK MASTER OUT 2 ECO STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC 01:FM 98.50MHz VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR Preset number Note To select a preset number for registering, press MEMORY once after tuning into the desired radio station, press PRESET to select a preset number, and then press MEMORY again. LINK MASTER OUT 2 ECO 02:Empty STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR “Empty” (not in use) or the frequency currently registered 39 En n Selecting a preset station n Clearing preset stations Tune into a registered radio station by selecting its preset number. Clear radio stations registered to the preset numbers. 1 2 1 2 3 Press FM/AM to select “TUNER” as the input source. Press PRESET repeatedly to select the desired radio station. SLEEP SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS Press FM/AM to select “TUNER” as the input source. Press OPTION. Use the cursor keys to select “Preset” and press ENTER. PROGRAM LINK MASTER OUT FM/AM USB INPUT VOLUME RED GREEN YELLOW LO 2 ECO BLUE MEMORY MUTE SETUP 4 5 OPTION TUNING ENTER RETURN TUNING DISPLAY TOP MENU HOME POP-UP/MENU PRESET RED GREEN YELLOW BLUE PRESET MEMORY TUNING TUNING PRESET OUT OUT 2 STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC 01:FM 98.50MHz FPR FPL SL SW SR SBL SB SBR Use the cursor keys (e/r) to select a preset station to be cleared and press ENTER. LINK MASTER ECO VOL. MUTE VIRTUAL Use the cursor keys (q/w) to select “CLEAR”. 2 ECO LINK MASTER STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC Preset BLUETOOTH STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC 01:FM 98.50MHz VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR Preset station to be cleared If the preset station is cleared, “Cleared” appears and then the next in-use preset number is displayed. Note “No Presets” appears when no radio stations are registered. 01:Cleared 6 7 40 En Repeat step 5 until all desired preset stations are cleared. To exit from the menu, press OPTION. Radio Data System tuning n Receiving traffic information automatically (U.K. and Europe models only) When “TUNER” is selected as the input source, the unit automatically receives traffic information. To enable this function, follow the procedure below to set the traffic information station. Radio Data System is a data transmission system used by FM stations in many countries. The unit can receive various types of Radio Data System data, such as “Program Service”, “Program Type”, “Radio Text” and “Clock Time”, when it is tuned into a Radio Data System broadcasting station. 1 2 n Displaying the Radio Data System information 1 Note We recommend using “Auto Preset” to tune into the Radio Data System broadcasting stations (p.38). ▪ To search upward/downward from the current frequency, press the cursor keys (q/w) while “READY” is displayed. ▪ To cancel the search, press RETURN. Press INFO repeatedly to select between the various display items. OUT ▪ Texts in parentheses denote indicators on the front display. The following screen appears for about 3 seconds when the search finishes. STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC LINK MASTER 2 ECO Program Type VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR LINK MASTER OUT 2 CLASSICS VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR Traffic information station (frequency) Note STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC LINK MASTER ECO STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC TP FM101.30MHz About 3 seconds after a display item is selected, its corresponding information appears. “TP Not Found” appears for about 3 seconds when no traffic information stations are found. VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR Information Program Service 2 ECO Item name OUT Use the cursor keys to select “Traffic Program” (TrafficProgram) and press ENTER. The traffic information station search will start in 5 seconds. Press ENTER again to start the search immediately. Tune into the desired Radio Data System broadcasting station. Note 2 When “TUNER” is selected as the input source, press OPTION. Program service name Program Type Current program type Radio Text Information on the current program Clock Time Current time DSP Program Sound mode name Audio Decoder Decoder name Frequency Frequency Note “Program Service”, “Program Type”, “Radio Text”, and “Clock Time” are not displayed if the radio station does not provide the Radio Data System service. 41 En Playing back music stored on a Bluetooth® device You can play back music files stored on a Bluetooth device (such as smartphones) on the unit. Also, you can enjoy audio played back on the unit using Bluetooth speakers/ headphones. 2 Please also refer to the owner’s manual of your Bluetooth device. Hold down MEMORY on the front panel or the remote control for more than 3 seconds. “Searching…” appears on the front display. Note ▪ You can also use the “Option” menu to pair a Bluetooth device. Press OPTION, and then use the cursor keys to select “Pairing”. The unit ▪ If another Bluetooth device is already connected, disconnect the Bluetooth connection before you perform a pairing operation. Bluetooth device (such as smartphones) ▪ To cancel pairing, press MEMORY. 3 4 The unit Turn on the Bluetooth function on your device. From the Bluetooth device list on your device, select “******* Yamaha” (*******: model name of the unit). After pairing has been completed and the unit is connected to the Bluetooth device, “Connected” appears on the front display. While a Bluetooth connection is established, the Bluetooth indicators light up. Bluetooth speakers/headphones Note LINK MASTER ▪ The Bluetooth device must support A2DP. OUT 2 ECO Connected ▪ To use the BLUETOOTH function, set “Bluetooth” (p.64) in the “Setup” menu to “On”. STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR ▪ You cannot make Bluetooth connections to a Bluetooth device (such as smartphones) and Bluetooth speakers/headphones at the same time. Note Connecting a Bluetooth® device (pairing) ▪ Complete a pairing procedure within 30 seconds. ▪ If you are prompted to input a passkey during a pairing procedure, input the numerals “0000”. ▪ If no Bluetooth devices are found, “Not found” appears. When connecting a Bluetooth device to the unit for the first time, a pairing operation is required. Pairing is an operation that registers the Bluetooth devices with each other beforehand. Once pairing has been completed, subsequent reconnection will be easy even after the Bluetooth connection is disconnected. 1 Press BLUETOOTH to select “Bluetooth” as the input source. 42 En Enjoying audio using Bluetooth® speakers/ headphones Playback of Bluetooth® device contents Connect a paired Bluetooth device and start playback. Check the following beforehand: Follow the procedure below to establish a Bluetooth connection between Bluetooth speakers/headphones and the unit. • Pairing has been completed. • Bluetooth function on the Bluetooth device is turned on. 1 1 Operate the Bluetooth device to establish a Bluetooth connection. Select an input source other than Bluetooth. Select the model name of the unit from the Bluetooth device list on your device. 2 3 4 When a connection is established, the unit’s input source automatically switches to “Bluetooth”. Note ▪ If you do not want the input source to switch automatically when a connection is established, set “Input Interlock” (p.47) to “Off” in the “Option” menu. ▪ You can operate the unit to search and connect the Bluetooth device (only the most recently connected device). In that case, follow one of the procedures below. 5 – Switch the input source to “Bluetooth”. – Press ENTER while the input source is “Bluetooth”. Otherwise, press OPTION and use the cursor keys to select “Connect”. Press SETUP. Use the cursor keys to select “Bluetooth” and press ENTER. Use the cursor keys to set “Bluetooth” to “On”, and then set “Transmitter” to “On” in the same way. Use the cursor keys to select “Device Search” to search the Bluetooth devices. The list of Bluetooth devices is displayed. ▪ If you cannot connect the device, please perform pairing again. 2 Use the input selection keys on the remote control to select an input source. 6 Operate the Bluetooth device to play back music. Note Select the Bluetooth speakers/headphones to be connected with the unit and press ENTER. When the connection process finishes, audio played back on the unit will be reproduced from the Bluetooth speakers/headphones. ▪ You cannot operate the unit to select or play back music, or display informations such as song names. Note ▪ Follow one of the procedures below to disconnect a Bluetooth connection. ▪ If the desired Bluetooth device is not displayed on the list, set the Bluetooth device to the pairing mode and then select “Device Search”. – Perform the disconnect operation on the Bluetooth device. – Press ENTER. ▪ Follow one of the procedures below to terminate the Bluetooth connection. – Press OPTION and use the cursor keys to select “Disconnect”. – Perform the disconnect operation on the Bluetooth speakers/headphones. – Switch the unit's input source to other than “Bluetooth”. – Press the SETUP key, then use the cursor keys to select "Bluetooth", then "Transmitter", and then "Off". – Press the SETUP key, then use the cursor keys to select "Bluetooth", then "Disconnect". 43 En Playing back music stored on a USB storage device You can play back music files stored on a USB storage device on the unit. Playback of USB storage device contents Note For details on playable USB devices, see “Supported devices and file formats” (p.79). Follow the procedure below to operate the USB storage device contents and start playback. Connecting a USB storage device You can control the USB memory device with the menu displayed on the TV screen. 1 Note ▪ Operations with TV screen are available only when your TV is connected to the unit via HDMI. Connect the USB storage device to the USB jack. ▪ “_” (underscore) will be displayed for characters not supported by the unit. The unit (front) 1 RADIO AUX Press USB to select “USB” as the input source. The browse screen (p.45) is displayed on the TV. USB STRAIGHT Note AUDIO If playback is ongoing on your USB storage device, the playback screen is displayed. 2 Use the cursor keys to select an item and press ENTER. If a song is selected, playback starts and the playback screen (p.45) is displayed. Note USB storage device ▪ To return to the previous screen, press RETURN. ▪ To switch the screen mode browse/playback/off, press DISPLAY. ▪ Files not supported by the unit cannot be selected. Note ▪ If the USB storage device contains many files, it may take time to load them. In this case, “Loading…” appears in the front display. ▪ Stop playback of the USB storage device before disconnect it from the USB jack. ▪ Connect a USB storage device directly to the USB jack of the unit. Do not use extension cables. ▪ The unit cannot charge USB devices while it is in standby mode. 44 En n Playback screen n Browse screen 1 4 1 2 5 2 3 1 List name 2 Contents list 1 Displays the list of USB storage device contents. Use the cursor keys to select an item and press ENTER to confirm the selection. 3 4 2 Status indicators Operation menu Press the cursor key (r) and then use the cursor keys (q/w) to select an item. Press ENTER to confirm the selection. Icon Playback information Displays the artist name, album name, song title, and elapsed time. Item number/total Display the current repeat/random settings (p.46) and playback status (such as play/pause). 5 Status indicators Display the current repeat/random settings (p.46) and playback status (such as play/pause). Function Moves 10 pages backward. Moves to the previous page of the list. Moves to the next page of the list. Moves 10 pages forward. Moves to the playback screen. Note A content selected by the cursor is displayed on the front display. 45 En Use the following remote control keys to control playback. n Repeat/random settings You can configure the repeat/random settings for playback of USB storage device contents. SLEEP SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS PROGRAM FM/AM RED USB INPUT VOLUME GREEN YELLOW LO 1 2 BLUE BLUETOOTH MEMORY MUTE SETUP OPTION TUNING ENTER RETURN TOP MENU TUNING External device operation keys DISPLAY HOME POP-UP/MENU PRESET RED GREEN YELLOW BLUE MEMORY TUNING TUNING When “USB” is selected as the input source, press OPTION. Use the cursor keys to select “Repeat” (Repeat) and press ENTER. PRESET Note ▪ To return to the previous screen during menu operations, press RETURN. External device operation keys ▪ Texts in parentheses denote indicators on the front display. Function a Resumes playback from pause or starts playback of the previously selected song. s Stops playback. d Stops playback temporarily. f g h j 3 Skips forward/backward. Searches forward/backward (by holding down). Note A content name of a current playback is displayed on the front display. To switch the displayed item, press INFO (p.30). 4 46 En Use the cursor keys (e/r) to select a setting. Setting Function Off (Off) Turns off the repeat function. One (One) Plays back the current song repeatedly. “c” appears on the TV screen. All (All) Plays back all songs in the current album (folder) repeatedly. “v” appears on the TV screen. Random (Random) Plays back songs in random order. “x” appears on the TV screen. To exit from the menu, press OPTION. Configuring playback settings for different playback sources (Option menu) You can configure separate playback settings for different playback sources. This menu is available on the front panel (or on the TV screen), allowing you to easily configure settings during playback. 1 Option menu items Note ▪ Available items vary depending on the selected input source. Press OPTION. LINK MASTER OUT 2 ECO ▪ Text in parentheses denotes indicators on the front display. ▪ Default settings are underlined. STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC Input Select VOL. MUTE VIRTUAL FPL FPR SL SW SR SBL SB SBR Front display Item Function Input Select (Input Select) Switches the input source. p.48 Tone Control (Tone Control) Adjusts the level of high-frequency range and lowfrequency range individually. p.48 Program (PRG) Select the sound programs and stereo playback. p.33 Sur.Decode (SrDec) Select which surround decoder is used when Sur.Decode is selected as the program. p.35 Adjusts the sound field effect level. p.48 Sets whether the dynamic range (from maximum to minimum) is automatically adjusted when the volume is adjusted. p.48 Enables/disables Compressed Music Enhancer. p.48 DSP Level DSP/Surround (DSP Level) (DSP/ Surround) Adaptive DRC (A.DRC) Enhancer (Enhancer) Input Trim Corrects volume differences between input sources. (In.Trim) Volume Trim (Volume Trim) Subwoofer Trim Fine-adjusts the subwoofer volume. (SW.Trim) p.49 Enables/disables the “Lipsync” setting in the “Setup” menu. p.49 Signal Info. (Signal Info.) Displays information about the video/audio signal. p.49 Audio In (Audio In) Combines the video jack of the selected input source with an audio jack of others. p.49 Video Out (Video Out) Selects a video to be output with the selected audio source. p.50 Use the cursor keys (e/r) to select a setting. FM Mode (FM Mode) Switches between “Stereo” and “Mono” for FM radio reception. p.37 To exit from the menu, press OPTION. Preset (Preset) Automatically registers FM radio stations with strong signals as presets. p.38 Clear radio stations registered to preset numbers. p.40 Use the cursor keys to select an item and press ENTER. Note To return to the previous screen during menu operations, press RETURN. 3 4 p.49 Lipsync (Lipsync) TV screen 2 Page Auto Preset Clear Preset Traffic Program (TrafficProgram) 47 En (U.K. and Europe models only) Automatically searches for a traffic information station. p.41 Item Function Repeat (Repeat) Configures the repeat setting for the USB storage device. p.46 Pairing (Pairing) Performs a pairing operation between the unit and your Bluetooth device. p.42 Connect/Disconnect (Connect/ Disconnect) Connects/disconnects the Bluetooth device. p.42 Input Interlock (Interlock) Sets whether the input source automatically switches to "Bluetooth" when a Bluetooth connection is established. p.43 n DSP/Surround (DSP/Surround) Page Configures the sound field program and surround settings. DSP Level (DSP Level) Adjusts the sound field effect level. Setting range -6 dB to 0 dB to +3 dB (1 dB increments) Adaptive DRC (A.DRC) n Input Select (Input Select) Sets whether the dynamic range (from maximum to minimum) is automatically adjusted when the volume level is adjusted. When it is set to “On”, it is useful for listening to playback at a low volume at night. Switches the input source. Press ENTER to switch to the selected input source. n Tone Control (Tone Control) Settings Adjusts the level of high-frequency range (Treble) and low-frequency range (Bass) individually. Choices On (On) Automatically adjusts the dynamic range. Off (Off) The dynamic range is not automatically adjusted. If “On” is selected, the dynamic range becomes narrow at a low volume and wide at a high volume. Treble (Treble), Bass (Bass) Setting range Enhancer (Enhancer) -6.0 dB to 0.0 dB to +6.0 dB (0.5 dB increments) Note Enables/disables Compressed Music Enhancer (p.36). ▪ When both “Treble” and “Bass” are 0.0 dB, “Bypass” appears. Note ▪ You can also adjust the tone with the front panel controls. Press TONE CONTROL to select “Treble” or “Bass”, then press PROGRAM to make an adjustment. ▪ This setting is applied separately to each input source. ▪ You can also use ENHANCER on the remote control to enable/disable Compressed Music Enhancer (p.36). ▪ If you set an extreme value, sounds may not match those from other channels. Settings Off (Off) Disables Compressed Music Enhancer. On (On) Enables Compressed Music Enhancer. Default Bluetooth, USB, TUNER: On (On) Others: Off (Off) 48 En n Volume Trim (Volume Trim) n Signal Info. (Signal Info.) Fine-adjusts volume difference between input sources or subwoofer volume. Displays information about the video/audio signal. Choices Input Trim (In.Trim) Corrects volume differences between input sources. If you are bothered by volume differences when switching between input sources, use this function to correct it. Format (FORMAT) The number of source channels in the input signal (front/surround/LFE) Channel (CHANNEL) Note This setting is applied separately to each input source. Audio format of the input signal For example, “3/2/0.1” means 3 front channels, 2 surround channels, and LFE. Sampling (SAMPLING) The number of samples per second of the input digital signal Setting range -6.0 dB to 0.0 dB to +6.0 dB (0.5 dB increments) Subwoofer Trim (SW.Trim) Video In (VIDEO IN) Type and resolution of the input digital signal Video Out (VIDEO OUT) Type and resolution of the output digital signal Note To switch the information on the front display, press the cursor keys (q/w) repeatedly. Fine-adjusts the subwoofer volume. n Audio In (Audio In) Setting range -6.0 dB to 0.0 dB to +6.0 dB (0.5 dB increments) Combines the video jack of the selected input source with an audio jack of others. For example, use this function in the following cases. n Lipsync (Lipsync) Enables/disables the adjustment configured in “Lipsync” (p.59) in the “Setup” menu. • Connecting a playback device that supports HDMI video output, but not HDMI audio output Note Input sources This setting is applied separately to each input source. HDMI 1-4, AV 1-3 Settigns Settings Off (Off) Disables the “Lipsync” adjustment. On (On) Enables the “Lipsync” adjustment. AV 1-3, AUDIO 1-2 Setup procedure See “Changing the combination of video/audio input jacks” (p.21). 49 En n Video Out (Video Out) Selects a video to be output with the selected audio source. For example, you can watch the video while listening to the radio. Input sources AUDIO, TUNER, USB, Bluetooth, AUX Settings Off (Off) Does not output video. HDMI 1-4, AV 1-3 Outputs video input through the corresponding video input jacks. 50 En CONFIGURATIONS Configuring various functions (Setup Menu) You can configure the unit’s various function with the menu displayed on the TV screen. Note Operations with TV screen are available only when your TV is connected to the unit via HDMI. If not, carry out operations while viewing the front display. 1 2 3 Press SETUP. Use the cursor keys to select a menu and press ENTER. Use the cursor keys to select an item and press ENTER. Note To return to the previous screen during menu operations, press RETURN. 4 5 Use the cursor keys (e/r) to select a setting and press ENTER. To exit from the menu, press SETUP. 51 En Setup menu items Menu Item Configuration Speaker Function Selects whether or not a subwoofer is connected. Front Selects the size of the front speakers. p.54 Center Selects whether or not a center speaker is connected and its size. p.54 p.55 Surround Selects whether or not surround speakers are connected and their size. Sets the lower limit of the low-frequency component that can be output from speakers whose size is set to “Small”. p.55 Subwoofer Phase Sets the phase of the subwoofer. p.55 Extra Bass Enables/disables Extra Bass. p.55 Virtual CINEMA FRONT Selects whether to use the front 5-channel speaker (Virtual CINEMA FRONT) configuration. p.55 Sets the distance between each speaker and listening position. p.55 Level Adjusts the volume of each speaker. p.56 Equalizer Adjusts the tone with an equalizer. p.56 Test Tone Enables/disables the test tone output. p.56 HDMI Control Enables/disables HDMI Control. p.57 Audio Output Enables/disables the audio output from a TV. p.57 4K Upscaling Enables/disables the upscaling function. p.57 TV Audio Input Selects an audio input jack of the unit to be used for TV audio input. p.57 Standby Sync Selects whether to use HDMI control to link the standby behavior of the TV and the unit. p.58 ARC Enables/disables ARC. p.58 SCENE Enables/disables SCENE link playback. p.58 Panorama Enables/disables the broadening effect of the front sound field. p.59 Center Width Adjusts the broadening effect of the center sound field. p.59 Dimension Adjusts the difference in level between the front and surround sound fields. p.59 Center Image Adjusts the center localization (broadening effect) of the front sound field. p.59 Select Selects the method to adjust the delay between video and audio output. p.59 Adjustment Adjusts the delay between video and audio output manually. p.60 Dialogue Level Adjusts the volume of dialogue sounds. p.60 Scale Switches the scale of the volume display. p.60 Dynamic Range Selects the dynamic range adjustment method for bitstream audio (Dolby Digital and DTS signals) playback. p.60 Max Volume Sets the limit value of the volume. p.60 Initial Volume Sets the initial volume for when this receiver is turned on. p.60 DSP Parameter Sound p.54 Crossover Distance HDMI Page Subwoofer Lipsync Dialogue Volume 52 En Menu ECO Function Bluetooth Item Function Auto Power Standby Set the amount of time for the auto-standby function. p.61 ECO Mode Enables/disables the eco mode (power saving mode). p.61 Input Rename Changes the input source name displayed on the front display. p.62 Input Skip Set which input source is skipped when operating the INPUT key. p.63 Dimmer Adjusts the brightness of the front display. p.63 Memory Guard Prevents accidental changes to the settings. p.63 Remote Color Key Set the unit's functions for the RED/GREEN/YELLOW/BLUE key of the remote control. p.64 Bluetooth Enables/disables the Bluetooth functions. p.64 Disconnect Terminates the Bluetooth connection between the Bluetooth device (such as smartphones) and the unit. p.42 Bluetooth Standby Selects whether to enable/disable the function that turns on the unit from Bluetooth devices (Bluetooth standby). p.64 Transmitter Enables/disables the Bluetooth audio transmitter function. p.65 Device Search Searches available Bluetooth devices (speakers/headphones) when the unit is used as a Bluetooth audio transmitter. p.43 Select an on-screen menu language. p.65 Audio Receive Audio Send Language Page 53 En Speaker Configures the speaker settings manually. Front Note Selects the size of the front speakers. Default settings are underlined. Settings n Configuration Select this option for small speakers. Small Configures the output characteristics of the speakers. Note Select this option for large speakers. When configuring the speaker size, as a general guideline, select “Large” if the woofer diameter of your speaker is 16 cm (6‑1/4”) or larger, or “Small” if it is smaller than 16 cm (6‑1/4”). Large “Front” is automatically set to “Large” when “Subwoofer” is set to “None”. Selects whether or not a subwoofer is connected. Center Settings Select this option when a subwoofer is connected. Selects whether or not a center speaker is connected and its size. The subwoofer will produce LFE (low-frequency effect) channel audio and low-frequency components from other channels. Settings Select this option for small speakers. Select this option when no subwoofer is connected. None The front speakers will produce all of the front channel frequency components. Note Subwoofer Use The subwoofer will produce front channel low-frequency components (configurable in “Crossover”). Small The front speakers will produce LFE (low-frequency effect) channel audio and low-frequency components from other channels. The subwoofer or front speakers will produce center channel lowfrequency components (configurable in “Crossover”). Select this option for large speakers. Large None 54 En The center speaker will produce all of the center channel frequency components. Select this option when no center speaker is connected. The front speakers will produce center channel audio. Surround Extra Bass Selects whether or not surround speakers are connected and their sizes. Enables/disables Extra Bass. When Extra Bass is enabled, you can enjoy enhanced bass sounds, regardless of the size of the front speakers and the presence or absence of the subwoofer. Settings Select this option for small speakers. Small Large Settings The subwoofer or front speakers will produce surround channel lowfrequency components (configurable in “Crossover”). Off Disables Extra Bass. Select this option for large speakers. On Enables Extra Bass. The surround speakers will produce all of the surround channel frequency components. Note You can also use BASS on the remote control to enable/disable Extra Bass (p.36). Select this option when no surround speakers are connected. None The front speakers will produce surround channel audio. Virtual CINEMA DSP works when you select a sound program. Virtual CINEMA FRONT Selects whether to use the front 5-channel speaker (Virtual CINEMA FRONT) configuration. Crossover Settings Sets the lower limit of the low-frequency components that can be output from a speaker whose size is set to “Small”. A frequency sound lower than the specified value will be produced from the subwoofer or front speakers. Settings Off Disables the front 5-channel speaker configuration. On Enables the front 5-channel speaker configuration. Note 40 Hz, 60 Hz, 80 Hz, 90 Hz, 100 Hz, 110 Hz, 120 Hz, 160 Hz, 200 Hz ▪ Select “On” only when utilizing the Virtual CINEMA FRONT configuration (p.13). Note ▪ This setting is not available when “Surround” is set to “None”. If the volume and crossover frequency are adjustable on your subwoofer, set the volume to half and crossover frequency to maximum. n Distance Subwoofer Phase Sets the distance between each speaker and listening position so that sounds from the speakers reach the listening position at the same time. First, select the unit of distance from “Meter” or “Feet”. Sets the phase of the subwoofer. When the bass sound is lacking or unclear, switch the subwoofer phase. Choices Settings Front L, Front R, Center, Surround L, Surround R, Subwoofer Normal Does not reverse the subwoofer phase. Reverse Reverses the subwoofer phase. Setting range 0.30 m to 24.00 m (1.0 ft to 80.0 ft), 0.05 m (0.2 ft) increments Default Front L, Front R, Subwoofer: 3.00 m (10.0 ft) Center: 2.60 m (8.6 ft) Others: 2.40 m (8.0 ft) 55 En n Manual equalizer adjustment n Level 1 2 Adjusts the volume of each speaker. Choices Front L, Front R, Center, Surround L, Surround R, Subwoofer Setting range -10.0 dB to +10.0 dB (0.5 dB increments) 3 Default Front L, Front R, Subwoofer: 0.0 dB 4 Adjusts the tone with an equalizer. To exit from the menu, press SETUP. n Test Tone EQ Select Enables/disables the test tone output. Test tone output helps you to adjust the speaker balance or equalizer while confirming its effect. Selects the type of equalizer to be used. Settings Off Use the cursor keys (q/w) to select the desired band (frequency) and the cursor keys (e/r) to adjust the gain. -6.0 dB to +6.0 dB n Equalizer GEQ Use the cursor keys (q/w) to select “Channel” and the cursor keys (e/r) to select the desired speaker channel. Setting range Others: -1.0 dB PEQ Set “EQ Select” to “GEQ”. Settings Applies the parametric equalizer values obtained by the YPAO measurement (p.25). Off Does not output test tones. Select this option when you want to adjust the equalizer manually. On Outputs test tones automatically when you adjust the speaker balance or equalizer. For details, see “Manual equalizer adjustment”. Does not use the equalizer. Note “PEQ” is available only when the YPAO has been performed (p.25). 56 En HDMI Configures the HDMI settings. n 4K Upscaling Note Enables/disables the upscaling function. When it is enabled, 1080p content is displayed at 4K resolution. Default settings are underlined. Settings n HDMI Control Enables/disables HDMI Control (p.80). Settings Off Note Settings To use HDMI control, you need to perform the HDMI Control link setup (p.80) after connecting HDMI Control-compatible devices. AV 1–3, AUDIO 1–2 Default AV 2 n Audio Output Note Enables/disables the audio output from a TV connected to the HDMI OUT jack. When using ARC to input TV audio to the unit, you cannot use the input jacks selected here for connecting an external device because the input will be used for TV audio input. Settings Disables the audio output from the TV. On Enables the audio output from the TV. Enables the upscaling function. Selects an audio input jack of the unit to be used for TV audio input when “HDMI Control” is set to “On”. The unit’s input source automatically switches to TV audio when the TV input is switched to its built-in tuner. Configure the settings in “TV Audio Input”, “Standby Sync”, “ARC”, and “SCENE”. Off Disables the upscaling function. On n TV Audio Input Disables HDMI Control. Enables HDMI Control. On Off Note This setting is available only when “HDMI Control” is set to “Off”. 57 En n Standby Sync n SCENE Select whether to use HDMI control to link the unit's standby mode to the TV's power when “HDMI Control” is set to “On”. Enables/disable SCENE link playback when “HDMI Control” is set to “On”. When SCENE link playback is enabled, HDMI Control-compatible devices connected to the unit via HDMI automatically works as follows, with a scene selection. Settings Off Does not set the unit to standby mode when the TV is turned off. On Sets the unit to standby mode when the TV is turned off. Auto • TV: turning on and displaying video from the playback device • Playback device: starting playback Choices (SCENE keys) Sets the unit to standby mode when the TV is turned off only when the unit is receiving TV audio or HDMI signals. BD / DVD, TV, CD, RADIO Settings n ARC Enables/disables ARC (p.19) when “HDMI Control” is set to “On”. Settings Off Disables SCENE link playback for the selected SCENE key. On Enables SCENE link playback for the selected SCENE key. Default Off Disables ARC. BD / DVD, TV: On On Enables ARC. CD, RADIO: Off Note You do not need to change this setting normally. In case noises are produced from the speakers connected to the unit because TV audio signals input to the unit via ARC are not supported by the unit, set “ARC” to “Off” and use the TV’s speakers. 58 Note SCENE link playback may not work properly due to the compatibility between devices. We recommend using TV and playback devices from the same manufacturer so that HDMI Control works more effectively. En Sound Configures the audio output settings. Center Image Note n DSP Parameter Adjusts the center localization (broadening effect) of the front sound field. Adjust this higher to strengthen the center localization (less broadening effect) or lower to weaken it (more broadening effect). This setting is effective when “Neo:6 Music” is selected. Configures the surround decoder settings. Setting range Default settings are underlined. 0.0 to 0.3 to 1.0 Panorama Enables/disables the broadening effect of the front sound field. When this function is enabled, you can wrap front left/right channel sounds around the sound field and generate a spacious sound field in combination with the surround sound field. This setting is effective when “DPL Music” is selected. Settings Off Disables the broadening effect of the front sound field. On Enables the broadening effect of the front sound field. n Lipsync Adjusts the delay between video and audio output. Note You can enable/disable the Lipsync function by input sources in “Lipsync (Lipsync)” (p.49) in the “Option” menu. Select Selects the method to adjust the delay between video and audio output. Center Width Setting range Adjusts the broadening effect of the center sound field. Higher to enhance the broadening effect, and lower to reduce it (closer to center). This setting is effective when “DPL Music” is selected. Manual Adjust the audio output timing in “Adjustment”. Setting range 0 to 3 to 7 Auto Dimension Adjusts the delay between video and audio output automatically when a TV that supports an automatic lipsync function is connected to the unit via HDMI. If necessary, you can fine-adjust the audio output timing in “Adjustment”. Adjusts the difference in level between the front and surround sound fields. Higher to strengthen the front sound field and lower to strengthen the surround sound field. This setting is effective when “DPL Music” is selected. Note “Select” is automatically set to “Manual” depending on the TV connected to the unit. Setting range -3 to 0 to +3 59 Select this option when you want to adjust the delay between video and audio output manually. En Adjustment Dynamic Range Adjusts the delay between video and audio output manually when “Select” is set to “Manual”. You can fine-adjust the audio output timing when “Select” is set to “Auto”. Selects the dynamic range adjustment method for bitstream audio (Dolby Digital and DTS signals) playback. Settings Setting range 0 ms to 500 ms (1 ms increments) n Dialogue Maximum Produces audio without adjusting the dynamic range. Standard Optimizes the dynamic range for regular home use. Min/Auto Adjusts the volume of dialogue sounds. Dialogue Level Sets the dynamic range for clear sound even at night or at low volumes. When playing back Dolby TrueHD signals, the dynamic range is automatically adjusted based on the input signal information. Max Volume Adjusts the volume of the center orientation sounds such as dialogue. Sets the limit value of the volume. Setting range Setting range 0 to 3 (higher to strengthen) -30.0 dB to +15.0 dB (5.0 dB increments), +16.5 dB [50.0 to 95.0 (5.0 increments), 97.0] n Volume Initial Volume Configures the volume settings. Sets the initial volume when the receiver is turned on. Scale Settings Switches the scale of the volume display. Settings Off Sets the level to the volume level of the unit when it last entered standby mode. Sets the unit to mute the audio output. dB Displays the volume in the “dB” unit. Mute 0-97 Displays the volume in the numeric value (0.5 to 97.0). -80.0 dB to +16.5 dB (0.5 dB increments) Sets the level to the specified volume level. [0.5 to 97.0 (0.5 increments)] 60 En ECO Configures the power supply settings. Note Default settings are underlined. n Auto Power Standby Set the amount of time for the auto-standby function. Settings Off Does not set the unit to standby mode automatically. 20 minutes Sets the unit to standby mode when you have not operated the unit and the unit has not detected any input signal for the specified time. 2 hours, 4 hours, 8 hours, 12 hours Sets the unit to standby mode when you have not operated the unit for the specified time. Default U.K. and Europe models: 20 minutes Other models: Off Note Just before the unit enters standby mode, “AutoPowerStdby” appears and then countdown starts in the front display. n ECO Mode You can reduce the unit’s power consumption by setting the eco mode to “On”. After setting, be sure to press ENTER to restart the unit. When the eco mode is enabled, you can reduce the unit’s power consumption. Settings Off Disables the eco mode. On Enables the eco mode. Note ▪ When “ECO Mode” is set to “On”, the front panel display may become dark. ▪ If you want to play audio at high volume, set “ECO Mode” to “Off”. 61 En Function Configures the functions that make the unit easier to use. Procedure to rename manually Note Default settings are underlined. 1 n Input Rename 2 Changes the input source name displayed on the front display. You can also select a name created by the Auto Rename function. 3 Default HDMI 1-4: Auto ▪ To cancel the entry, select “CANCEL”. Procedure to rename automatically ▪ If you select "RESET", the default input name will be inserted into the editing area. 4 5 Use the cursor keys (q/w) to select an input source to be renamed. Use the cursor keys (e/r) to select “Auto”. The unit creates a name automatically according to the connected device. 3 4 Use the cursor keys and ENTER key to edit the name, and then select “OK” and press ENTER. Note Others: Manual (For USB, Bluetooth, AUX only “Manual” can be selected.) 2 Use the cursor keys (e/r) to select “Manual” and press ENTER. The edit screen is displayed. Input sources HDMI 1-4, AUDIO 1-2, AV 1-3, USB, Bluetooth, AUX 1 Use the cursor keys (q/w) to select an input source to be renamed. To change another input source, repeat steps 1 to 2. To exit from the menu, press SETUP. Note During selecting “Auto”, the created name is saved even after the device connection is terminated. To reset to the default setting, switch the setting to “Manual” at once and then set it again to “Auto”. 62 En To change another input source name, repeat steps 1 to 4. To exit from the menu, press SETUP. n Input Skip n Dimmer Set which input source is skipped when operating the INPUT key. Adjusts the brightness of the front display. You can select the desired input source quickly by using this function. Setting range Input sources -4 to 0 (higher to brighten) HDMI 1-4, AUDIO 1-2, AV 1-3, TUNER, USB, Bluetooth, AUX Note Settings The front display may become dark when “ECO Mode” (p.61) is set to “On”. Off Does not skip the selected input source. On Skips the selected input source. n Memory Guard Prevents accidental changes to the settings. Settings Off Does not protect the settings. On Protects the settings until “Off” is selected. Note When “Memory Guard” is set to “On”, the lock icon (o) is displayed on the menu screen. 63 En n Remote Color Key Bluetooth Set the unit's functions for the RED/GREEN/YELLOW/BLUE key of the remote control. Configures the Bluetooth settings. Settings Default n Bluetooth Assigns the functions of playback devices connected to the unit with an HDMI cable. Enables/disables the Bluetooth function (p.42). Assigns the unit's input sources to each key. The assigned input sources can be set separately. Input Settings Input sources HDMI 1-4, AUDIO 1-2, AV 1-3, TUNER, USB, Bluetooth, AUX Default RED: HDMI2, GREEN: HDMI4, YELLOW: AV 2, BLUE: AUX Disables the Bluetooth function. Enables the Bluetooth function. n Audio Receive Assigns the functions of sound mode to each key. Configures the Bluetooth settings when the unit is used as the Bluetooth audio receiver. RED: MOVIE GREEN: MUSIC Program Off On YELLOW: STEREO Bluetooth Standby BLUE: SUR.DECODE For example, if you press the RED key repeatedly, you can select your favorite sound program from the sound programs (MOVIE) (p.33) suitable for the video source. Selects whether to enable/disable the function that turns on the unit from Bluetooth devices (Bluetooth standby). If this function is set to “On”, the unit automatically turns on when a connect operation is performed on the Bluetooth device. Settings 64 En Off Disables the Bluetooth standby function. On Enables the Bluetooth standby function. (The unit consumes more power than when “Off” is selected.) n Audio Send Language Configures the Bluetooth settings when the unit is used as the Bluetooth audio transmitter. Select an on-screen menu language. Note Transmitter Default settings are underlined. Enables/disables the Bluetooth audio transmitter function. Settings When this function is enabled, you can enjoy audio played back on the unit using Bluetooth speakers/headphones (p.43). English English 日本語 Japanese Settings Français French Deutsch German Español Spanish Русский Russian Italiano Italian 中文 Chinese Off Disables the Bluetooth audio transmitter function. On Enables the Bluetooth audio transmitter function. Note The information on the front display is provided in English only. 65 En Configuring the system settings (ADVANCED SETUP menu) Configure the system settings of the unit while viewing the front display. 1 2 ADVANCED SETUP menu items Set the unit to standby mode. Note Default settings are underlined. While holding down STRAIGHT on the front panel, press z (power). Item SP IMP. z (power) REMOTE ID 3 4 5 STRAIGHT Press PROGRAM to select an item. Page (U.S.A. and Canada models only) Changes the speaker impedance setting. Selects the unit’s remote control ID. (Asia, Taiwan and General models only) TU PROGRAM Function Changes the FM/AM tuning frequency setting. p.66 p.67 p.67 TV FORMAT Switches the video signal type of HDMI output. p.67 4K MODE Selects the HDMI 4K signal format. p.68 INIT Restores the default settings. p.68 UPDATE Updates the firmware. p.68 VERSION Checks the version of firmware currently installed on the unit. p.68 Press STRAIGHT to select a setting. Changing the speaker impedance setting (SP IMP.) Press z (power) to set the unit to standby mode and turn it on again. (U.S.A. and Canada models only) The new settings take effect. LINK MASTER OUT 2 ECO STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC SP IMP.••8¬MIN VOL. MUTE VIRTUAL FPR FPL SL SW SR SBL SB SBR Change the unit’s speaker impedance settings depending on the impedance of the speakers connected. Settings 66 6 Ω MIN Select this option when you connect 6-ohm speakers to the unit. 8 Ω MIN Select this option when you connect 8-ohm or higher speakers to the unit. En Selecting the remote control ID (REMOTE ID) STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC LINK MASTER OUT Switching the video signal type (TV FORMAT) 2 ECO REMOTE ID••ID1 LINK MASTER OUT 2 ECO VOL. MUTE VIRTUAL STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC TV FORMAT•NTSC FPR FPL SL SW SR SBL SB SBR Change the unit’s remote control ID so that it matches the remote control’s ID (default: ID1). When using multiple Yamaha AV receivers, you can set each remote control with a unique remote control ID for its corresponding receiver. VOL. MUTE VIRTUAL FPR FPL SL SW SR SBL SB SBR Switch the video signal type of HDMI output so that it matches to the format of your TV. Settings Since the unit automatically selects the video signal type so that it matches to the TV, it is unnecessary to change the setting normally. Change the setting only when images on the TV screen do not appear correctly. ID1, ID2 Settings NTSC, PAL n Changing the remote control ID of the remote control 1 Default U.S.A., Canada, Korea, Taiwan and General models: NTSC To select ID1, while holding down the cursor key (e), hold down SCENE (BD/DVD) for more than 3 seconds. To select ID2, while holding down the cursor key (e), hold down SCENE (TV) for more than 3 seconds. Other models: PAL Changing the FM/AM tuning frequency setting (TU) (Asia, Taiwan and General models only) LINK MASTER OUT 2 ECO STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC TU••••FM50/AM9 VOL. MUTE VIRTUAL FPR FPL SL SW SR SBL SB SBR Change the FM/AM tuning frequency setting of the unit depending on your country or region. Settings FM100/AM10 Select this when you want to adjust the FM frequency by 100-kHz steps and AM by 10-kHz steps. FM50/AM9 Select this when you want to adjust the FM frequency by 50-kHz steps and AM by 9-kHz steps. 67 En Selecting the HDMI 4K signal format (4K MODE) LINK MASTER OUT 2 ECO Updating the firmware (UPDATE) STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC 4K MODE•MODE 1 LINK MASTER OUT Settings MODE 1 Inputs/outputs 4K signals shown in the table below. Depending on the connected device or HDMI cables, video may not be displayed correctly. In this case, select “MODE 2”. MODE 2 Inputs/outputs 4K signals shown in the table below. Do not perform this procedure unless firmware update is necessary. Also, make sure you read the information supplied with updates before updating the firmware. 1 2 3 4 Format 8 bit 4K/30, 25, 24 Hz 4 YCbCr 4:4:4 4 MODE 2 10 bit 12 bit 8 bit – 10 bit 12 bit – – – YCbCr 4:2:2 4 YCbCr 4:2:0 4 4 – RGB 4:4:4 4 4 – YCbCr 4:4:4 4 4 – YCbCr 4:2:2 4 – OUT 2 ECO LINK MASTER OUT 2 ECO Press PROGRAM on the front panel to select “UPDATE”. Connect the USB memory device to the USB jack. To start firmware update, press INFO on the front panel. STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC VERSION••xx.xx 4 VOL. MUTE VIRTUAL FPR FPL SL SW SR SBL SB SBR Check the version of firmware currently installed on the unit. Note It may take a while until the firmware version is displayed. STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC INIT••••CANCEL Save the downloaded firmware to the root folder of a USB memory device. Checking the firmware version (VERSION) Restoring the default settings (INIT) LINK MASTER FPR FPL SL SW SR SBL SB SBR n Firmware update procedure When “MODE 1” is selected, use a Premium High Speed HDMI Cable or Premium High Speed Cable with Ethernet. RGB 4:4:4 VOL. MUTE VIRTUAL New firmware that provides additional features or product improvements will be released as needed. Updates can be downloaded from our website. For details, refer to the information supplied with updates. Note MODE 1 STEREO TUNED ZONE SLEEP PARTY 2 A 3 B Hi -Res ENHANCER YPAO VOL. A- DRC UPDATE•••••USB FPR FPL SL SW SR SBL SB SBR Selects the format of signals input/output at the unit when HDMI 4K compatible TV and playback device are connected to the unit. 4K/60, 50 Hz 2 ECO VOL. MUTE VIRTUAL VOL. MUTE VIRTUAL FPR FPL SL SW SR SBL SB SBR Restores the default settings for the unit. Choices ALL Restores the default settings for the unit. CANCEL Does not perform an initialization. 68 En APPENDIX Frequently asked questions The unit’s remote control is simultaneously controlling another Yamaha product as well as the unit... The frequently asked questions from customers and the answers are shown below. The new speaker system does not provide an ideal sound balance... When using multiple Yamaha products, the remote control may work on another Yamaha product or another remote control may work on the unit. If this happens, register different remote control IDs for the devices that you want to control with each remote control (p.67). If you have changed speakers or have a new speaker system, use YPAO to optimize the speaker settings again (p.25). If you want to adjust the speaker settings manually, use “Speaker” in the “Setup” menu (p.54). We want to set limitations on the volume control... The combination of video/audio input jacks does not match an external device... If someone accidentally operates the controls on the main unit or remote control, the volume may suddenly increase. This may also cause injury or damage the unit or speakers. We recommend using “Max Volume” in the “Setup” menu to set the maximum volume level for the unit in advance (p.60). Use “Audio In” in the “Option” menu to change the combination of video/audio input jacks so that it matches the output jack(s) of your external device (p.21). Video and audio are not synchronized... I want to fix the volume when turning on the unit... Use “Lipsync” in the “Setup” menu to adjust the delay between video and audio output (p.59). By default, the volume level when the unit last entered standby mode is automatically applied. If you want to fix the volume, use “Initial Volume” in the “Setup” menu to set the volume to be applied when the receiver is turned on (p.60). I want to hear audio from the TV speakers... Use “Audio Output” in the “Setup” menu to enable audio output from the TV speakers (p.57). The volume varies depending on the input sources... You can correct volume differences between input sources by utilizing “Input Trim” in the “Option” menu (p.49). I want to change the on-screen menu language... Use “Language” in the “Setup” menu to select a language from English, Japanese, French, German, Spanish, Russian, Italian and Chinese (p.24). HDMI Control does not work at all... To use HDMI Control, you need to perform the HDMI Control link setup (p.80). After connecting HDMI Control-compatible devices (such as BD/DVD players) to the unit, enable HDMI Control on each device and perform the HDMI Control link setup. This setup is required every time you add a new HDMI Control-compatible device to your system. For information on how HDMI Control works between your TV and playback devices, refer to the instruction manuals for each device. I want to update the firmware... Use “UPDATE” in the “ADVANCED SETUP” menu to update the unit’s firmware (p.68). I want to change the input source name... By default, input source names (such as “HDMI1” and “AV 1”) are displayed on the front display when an input source is selected. If you want to rename them as you like, use “Input Rename” (p.62) in the “Setup” menu. I want to prevent accidental changes to the settings... You can protect the settings configured on the unit (such as speaker settings) by utilizing “Memory Guard” in the “Setup” menu (p.63). 69 En Troubleshooting Refer to the table below when the unit does not function properly. If the problem you are experiencing is not listed below or if the instructions below do not help, turn off the unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. First, check the following: 1 2 3 The power cables of the unit, TV and playback devices (such as BD/DVD players) are connected to AC wall outlets securely. The unit, subwoofer, TV and playback devices (such as BD/DVD players) are turned on. The connectors of each cable are securely inserted in to jacks on each device. Power, system and remote control Problem Cause Remedy The power does not turn on. The protection circuitry has been activated three times consecutively. If the unit is in this condition, the standby indicator on the unit blinks when you try to turn on the power. As a safety precaution, capability to turn on the power is disabled. Contact your nearest Yamaha dealer or service center to request repair. The power does not turn off. The internal microcomputer has frozen, due to an external electric Hold down z (power) on the front panel for more than 15 seconds to reboot the shock (such as lightning or excessive static electricity) or to a drop unit. (If the problem persists, disconnect the power cable from the AC wall outlet in the power supply voltage. and plug it again.) The power turns off (standby mode) immediately. The unit was turned on while a speaker cable was shorted. The sleep timer worked. The unit enters standby mode automatically. The unit is not reacting. Twist the bare wires of each speaker cable firmly and reconnect to the unit and speakers (p.17). Turn on the unit and start playback again. The auto-standby function activated because the unit was not used To disable the auto-standby function, set “Auto Power Standby” in the “Setup” for the specified time. menu to “Off” (p.61). The speaker impedance setting is incorrect. Set the speaker impedance to match your speakers (p.66). The protection circuitry has been activated because of a short circuit. Twist the bare wires of each speaker cable firmly and reconnect to the unit and speakers (p.17). Hold down z (power) on the front panel for more than 15 seconds to reboot the The internal microcomputer is frozen, due to an external electric shock (such as lightning or excessive static electricity) or to a drop unit. (If the problem persists, disconnect the power cable from the AC wall outlet in the power supply voltage. and plug it again.) 70 En Problem The unit cannot be controlled using the remote control. Cannot select the desired input source even if “INPUT” is pressed. The RED/GREEN/YELLOW/BLUE keys of the remote control do not operate. Cause Remedy The unit is out of the operating range. Use the remote control within the operating range (p.4). The batteries are weak. Replace with new batteries. The unit’s remote control sensor is exposed to direct sunlight or strong lighting. Adjust the lighting angle, or reposition the unit. The remote control IDs of the unit and the remote control are not identical. Change the remote control ID of the unit or the remote control (p.67). The function which skips some input sources is set. Set “Input Skip” of the desired input source in the “Setup” menu to “Off” (p.63). The device which is connected to the unit via HDMI does not support the operation of the RED/GREEN/YELLOW/BLUE keys. Use a device which supports the operation of the RED/GREEN/YELLOW/BLUE keys. The settings of the RED/GREEN/YELLOW/BLUE keys of the unit's remote control have been changed. Set the “Remote Color Key” settings in the “Setup” menu to “Default” (p.64). Audio Problem No sound. The volume cannot be increased. No sound is coming from a specific speaker. Cause Remedy Another input source is selected. Select an appropriate input source with the input selection keys. Signals that the unit cannot reproduce are being input. Some digital audio formats cannot be played back on the unit. To check the audio format of the input signal, use “Signal Info.” in the “Option” menu (p.49). The cable connecting the unit and playback device is defective. If there is no problem with the connection, replace with another cable. The maximum volume is set. Use “Max Volume” in the “Setup” menu to adjust the maximum volume (p.60). A device connected to the output jacks of the unit is not turned on. Turn on all devices connected to the output jacks of the unit. The playback source does not contain a signal for the channel. To check it, use “Signal Info.” in the “Option” menu (p.49). The currently selected sound program/decoder does not use the speaker. To check it, select “5ch Stereo” (p.32). Audio output of the speaker is disabled. Perform YPAO (p.25) or use “Configuration” in the “Setup” menu to change the speaker settings (p.54). The volume of the speaker is set too low. Perform YPAO (p.25) or use “Level” in the “Setup” menu to adjust the speaker volume (p.56). The speaker cable connecting the unit and the speaker is defective. If there is no problem with the connection, replace with another speaker cable. The speaker is malfunctioning. To check it, replace with another speaker. If the problem persists, the unit may be malfunctioning. 71 En Problem Cause Remedy The playback source does not contain Low Frequency Effect (LFE) To check it, set “Extra Bass” in the “Setup” menu to “On”, in order to output the or low-frequency signals. front channel low-frequency components from the subwoofer (p.55). No sound is coming from the subwoofer. Subwoofer output is disabled. Perform YPAO (p.25) or set “Subwoofer” in the “Setup” menu to “Use” (p.54). The volume of the subwoofer is too low. Adjust the volume on the subwoofer. The subwoofer has been turned off by its auto-standby function. Disable the auto-standby function of the subwoofer or adjust its sensitivity level. The TV does not support HDCP (High-bandwidth Digital Content No sound from the playback device (connected to Protection). the unit with HDMI). The number of devices connected to the HDMI OUT jack exceeds the limit. No sound from the TV (when HDMI Control is used). Refer to the instruction manuals for the TV and check the TV’s specifications. Disconnect some of the HDMI devices. The TV is set to output audio from the TV speakers. Change the audio output setting on your TV so that the TV audio is output from the speakers connected to the unit. A TV that does not support ARC is connected to the unit only with an HDMI cable. Use a digital optical cable to make an audio connection (p.19). (If the TV is connected to the unit with an audio cable) The TV audio input setting does not match the actual connection. (If you are trying to use ARC) Use “TV Audio Input” in the “Setup” menu to select the correct audio input jack (p.57). Set “ARC” in the “Setup” menu to “On” (p.58). Also, enable ARC on the TV. ARC is disabled on the unit or TV. When playing back DSD audio, the unit disables the audio output from a TV. The unit does not support DSD audio output from a TV. Change the audio output setting on the playback device to PCM. Only the front speakers work on multichannel audio. The playback device is set to output 2-channel audio (such as PCM) only. To check it, use “Signal Info.” in the “Option” menu (p.49). If necessary, change the digital audio output setting on the playback device. Noise/hum is heard. The sound is distorted. The unit is too close to another digital or radio frequency device. Move the unit further away from the device. The cable connecting the unit and playback device is defective. If there is no problem with the connection, replace with another cable. The volume of the unit is too high. Turn down the volume. If “ECO Mode” in the “Setup” menu is set to “On”, set it to “Off” (p.61). A device connected to the unit’s output jacks is not turned on. Turn on all devices connected to the unit’s output jacks. 72 En Video Problem No video. No video from the playback device (connected to the unit with HDMI). No image (contents required the HDCP 2.2 compatible HDMI device) from the playback device connected to the unit with HDMI. The menu of the unit is not displayed on the TV. Cause Remedy Another input source is selected on the unit. Select an appropriate input source with the input selection keys. Another input source is selected on the TV. Switch the TV input to display the video from the unit. The video signal output from the unit is not supported by the TV. Check the video output setting of the playback device. For information about video signals supported by the TV, refer to the instruction manuals for the TV. The cable connecting the unit and TV (or playback device) is defective. If there is no problem with the connection, replace with another cable. The input video signal (resolution) is not supported by the unit. To check the information about the current video signal (resolution), use “Signal Info.” in the “Option” menu (p.49). For information about video signals supported by the unit, see “HDMI signal compatibility” (p.82). The TV does not support HDCP (High-bandwidth Digital Content Protection). Refer to the instruction manuals for the TV and check the TV’s specifications. The number of devices connected to the HDMI OUT jack is over the limit. Disconnect some of the HDMI devices. The TV (HDMI input jack) does not support HDCP 2.2. (The Warning message can be displayed on the TV screen.) Connect the unit to the TV (HDMI input jack) that supports HDCP 2.2. The TV is not connected to the unit via HDMI. You can display the menu of the unit on the TV only when they are connected with an HDMI cable. If necessary, use an HDMI cable to connect them (p.19 to p.20). Another input source is selected on the TV. Switch the TV input to display the video from the unit (HDMI OUT jack). 73 En FM/AM radio Problem FM radio reception is weak or noisy. Cause Remedy There is multi-path interference. Adjust the FM antenna height or orientation, or place it in a different location. Your area is too far from the FM station transmitter. To select monaural FM radio reception “FM Mode” in the “Option” menu to “Mono” (p.37). The noises may be caused by fluorescent lamps, motors, thermostats, or other electrical equipment. It is difficult to completely eliminate noise. It may be reduced by using an outdoor AM antenna. Use an outdoor FM antenna. AM radio reception is weak or noisy. Select the station manually (p.37). Your area is too far from the FM station transmitter. Use an outdoor antenna. We recommend using a sensitive multi-element antenna. Adjust the AM antenna orientation. Radio stations cannot be selected automatically. Select the station manually (p.37). The AM radio signal is weak. AM radio stations cannot be registered as presets. Use an outdoor AM antenna. Connect it to the ANTENNA (AM) jack together with the supplied AM antenna. Auto Preset is for registering FM radio stations only. Register AM radio stations manually (p.38). Auto Preset has been used. USB Problem The unit does not detect the USB device. Folders and files in the USB device cannot be viewed. Cause Remedy The USB device is not connected to the USB jack securely. Turn off the unit, reconnect your USB device, and turn the unit on again. The file system of the USB device is not FAT 16 or FAT 32. Use a USB device with FAT 16 or FAT 32 format, except USB HDDs. The folder structure not supported by the unit is applied. The unit supports folder hierarchies of up to eight levels and up to 65,000 files per level. If necessary, modify the folder structure on your USB device. 74 En Bluetooth® Problem Cannot make the unit pair with a Bluetooth device. Cannot make a Bluetooth connection. Cause Remedy Another Bluetooth device is connected. Terminate current Bluetooth connection, and perform pairing with the new device. This unit and the device are too far apart. Move the device closer to this unit. There is a device (microwave oven, wireless LAN, etc.) that outputs Move this unit away from the device that is emitting radio-frequency signals. signals in the 2.4 GHz frequency band nearby. The Bluetooth device does not support A2DP. Perform pairing with a device which supports A2DP. Another Bluetooth device is connected. Terminate current Bluetooth connection, then establish a Bluetooth connection with that device again. The Bluetooth function of the device is turned off. Turn on the Bluetooth function of the device. Delete the pairing information on the device, and then perform pairing again (p.42). The pairing information has been deleted. This unit can be paired with sixteen devices. If pairing with a seventeenth device is performed, the pairing information with the earliest connection date will be deleted. The pairing information is removed from/not registered on the Bluetooth connection list. Perform paring again (p.42). The volume of the connecting device is set too low. Turn up the volume of the connecting device. The connecting device is not set to send Bluetooth audio signals to Switch the output of Bluetooth audio signals of the connecting device to the unit. the unit. No sound is produced, or the sound is interrupted during playback. The Bluetooth connection of the unit with the device has terminated. Perform Bluetooth connection operations again (p.42). There is a device (microwave oven, wireless LAN, etc.) that outputs Move this unit away from the device that is emitting radio-frequency signals. signals in the 2.4 GHz frequency band nearby. This unit and the connecting device are too far apart. 75 En Move the connecting device closer to this unit. Error indications on the front display Refer to the table below when the error message is indicated on the front display. Message Cause Remedy Access error The unit cannot access the USB device. Turn off the unit and reconnect your USB device. If the problem persists, try another USB device. Check SP Wires The speaker cables short circuit. Twist the bare wires of the cables firmly and connect to the unit and speakers properly. Internal Error An internal error has occurred. Contact the nearest authorized Yamaha dealer or service center. No content There are no playable files in the selected folder. Select a folder that contains files supported by the unit. Not found The Bluetooth device is not found. RemID Mismatch The remote control IDs of the unit and the remote control are not identical. • Place the Bluetooth device within 10 m (32 ft) of the Bluetooth receiver. • Perform pairing again. Change the remote control ID of the unit or the remote control (p.67). 76 En Glossary This is a glossary of the technical terms used in this manual. DTS Neo: 6 Audio information DTS Neo: 6 enables 6-channel playback from 2-channel sources. There are two modes available: “Music mode” for music sources and “Cinema mode” for movie sources. This technology provides discrete full-bandwidth matrix channels of surround sound. DSD (Direct Stream Digital) n Audio decoding format DSD (Direct Stream Digital) technology stores audio signals on digital storage media, such as SACD (Super Audio CDs). The signals are stored at a high-frequency sampling rate of 2.8224 MHz. The highest frequency response is equal to or higher than 100 kHz, with a dynamic range of 120 dB. This technology offers better audio quality than that used for CDs. Dolby Digital Dolby Digital is a compressed digital audio format developed by Dolby Laboratories, Inc. that supports 5.1-channel audio. This technology is used for audio on most DVD disc. MP3 Dolby Pro Logic II One of the compressed digital audio format used by MPEG. With psychoacoustic technologies, this compression method achieves a high compression rate. Reportedly, it is capable of compressing data quantity by about 1/10 maintaining a certain level of audio quality. Dolby Pro Logic II enables 5-channel playback from 2-channel sources. There are three modes available: “Music mode” for music sources, “Movie mode” for movie sources, and “Game mode” for game sources. MPEG-4 AAC Dolby TrueHD Dolby TrueHD is an advanced lossless audio format developed by Dolby Laboratories, Inc. to offer a high-definition home theater experience with the quality of the studio master. Dolby TrueHD can carry up to eight channels of 96 kHz/24-bit audio (up to six channels of 192 kHz/24-bit audio) simultaneously. This technology is used for audio on BD (Blu-ray Disc). DTS 96/24 DTS 96/24 is a compressed digital audio format that supports 5.1-channel and 96 kHz/24-bit audio. This format remains fully compatible with the existing multichannel audio systems that support DTS Digital Surround. This technology is used for music DVDs, etc. An MPEG-4 audio standard. It is used for mobile telephones, portable audio players, and audio streaming services on Internet because it allows a high compression rate of data while maintaining better audio quality than MP3. PCM (Pulse Code Modulation) PCM is a signal format under which an analog audio signal is digitized, recorded, and transmitted. This technology is the basis of all other audio format. This technology is used as a lossless audio format called Linear PCM for audio on a variety of media, including CDs and BD (Blu-ray Disc). Sampling frequency/Quantization bit Sampling frequency and quantization bits indicate the quantity of information when an analog audio signal is digitized. These values are noted as in the following example: “48 kHz/24-bit”. DTS Digital Surround DTS Digital Surround is a compressed digital audio format developed by DTS, Inc. that supports 5.1-channel audio. This technology is used for audio on most DVD discs. • Sampling frequency Sampling frequency (the number of times the signal is sampled per second) is called the sampling rate. When the sampling frequency is higher, the range of frequencies that can be played back are wider. DTS Express DTS Express is a compressed digital audio format that supports 5.1-channel audio and allows a higher compression rate than the DTS Digital Surround format developed by DTS, Inc. This technology is developed for audio streaming services on the Internet and secondary audio on BD (Blu-ray Disc). • Quantization bit The number of quantization bits indicate the degree of accuracy when converting the sound level into a numeric value. When the number of quantized bits is higher, the expression of the sound level is more accurate. DTS-HD High Resolution Audio DTS-HD High Resolution Audio is a compressed digital audio format developed by DTS, Inc. that supports 7.1-channel and 96 kHz/24-bit audio. DTS-HD High Resolution Audio remains fully compatible with the existing multichannel audio systems that support DTS Digital Surround. This technology is used for audio on most BD (Blu-ray Disc). WAV DTS-HD Master Audio WMA (Windows Media Audio) DTS-HD Master Audio is an advanced lossless audio format developed to offer a high-definition home theater experience with the quality of the studio master by DTS, Inc. DTS-HD Master Audio can carry up to eight channels of 96 kHz/24-bit audio (up to six channels of 192 kHz/24-bit audio) simultaneously. This technology is used for audio on BD (Blu-ray Disc). One of the compressed digital audio formats developed by Microsoft Corporation. With psychoacoustic technologies, this compression method achieves a high compression rate. Reportedly, it is capable of compressing data quantity by about 1/20 maintaining a certain level of audio quality. Windows standard audio file format, which defines the method of recording the digital data obtained by converting audio signals. By default, the PCM method (no compression) is used, but you can also use other compression methods. 77 En n Others Compressed Music Enhancer LFE (Low Frequency Effects) 0.1 channel This channel reproduces low-frequency bass signals and has a frequency range from 20 Hz to 120 Hz. This channel is added to the channels for all bands with Dolby Digital or DTS to enhance low frequency audio effects. This channel is labeled 0.1 because it is limited to only low frequency audio. Lip sync Video output sometimes lags behind audio output due to the complexity of signal processing caused by an increase in video signal capacity. Lip sync is a technique for automatically correcting the timing lag between audio and video output. The Compressed Music Enhancer feature compensates for missing harmonics in compression music formats (such as MP3). As a result, this technology provides improved performance for the overall sound system. SILENT CINEMA Yamaha has developed a natural, realistic sound effect DSP algorithm for headphones. Parameters for headphones have been set for each sound program, so that accurate representations of all the sound programs can be enjoyed on headphones. Virtual CINEMA DSP Virtual CINEMA DSP allows the system to virtually reproduce the sound field of the surround speakers with front left and right speakers. Even if the surround speakers are not connected, the unit creates the realistic sound field in a listening room. HDMI and video information YPAO (Yamaha Parametric room Acoustic Optimizer) The Yamaha Parametric room Acoustic Optimizer (YPAO) function detects speaker connections, measures the distances from them to your listening position(s), and then automatically optimizes the speaker settings, such as volume balance and acoustic parameters, to suit your room. Composite video signal With the composite video signal system, color, brightness, and synchronization data signals are combined and transmitted with a single cable. Deep Color Deep Color is a technology that HDMI specification supports. Deep Color increases the number of available colors within the boundaries defined by the RGB or YCbCr color space. Conventional color systems process the color using 8 bits. Deep Color processes the color with 10, 12, or 16 bits. This technology allows HDTVs and other displays to increase from millions of colors to billions of colors and eliminate on-screen color banding for smooth tonal transitions and subtle gradations between colors. HDMI HDMI (High-Definition Multimedia Interface) is the world-wide standard interface for digital audio/ video signal transmission. This interface transmits both digital audio and digital video signals using a single cable without any loss. HDMI complies with HDCP (High-bandwidth Digital Content Protection) and provides a secure audio/video interface. For further information on HDMI, visit the HDMI website at “http://www.hdmi.org/”. x.v.Color “x.v.Color” is a technology that the HDMI specification supports. It is a more extensive color space than sRGB and allows the expression of colors that were not hitherto possible. While remaining compatible with the color gamut of sRGB standards, “x.v.Color” expands the color space, and thus can produce more vivid, natural images. Yamaha technologies CINEMA DSP (Digital Sound Field Processor) Since the surround sound systems were originally designed for use in movie theaters, their effect is best experienced in a theater that has many speakers designed for acoustic effects. Since home conditions (such as room size, wall material, and number of speakers) can differ so widely, it is inevitable that there are differences in the sound that you hear. Based on a wealth of actually measured data, CINEMA DSP, Yamaha’s original DSP technology provides the audiovisual experience of a movie theater in your own home. 78 En Supported devices and file formats Video signal flow The following devices and file formats can be used by the unit. Video signals input from a video device to the unit are output to a TV as shown below. Video device Supported devices The unit TV n USB devices • This unit supports USB mass storage class devices (e.g., flash memories or portable audio players) using FAT16 or FAT32 format. • Do not connect devices other than USB mass storage class devices (such as USB chargers or USB hubs), PCs, card readers, an external HDD, etc. HDMI connection • USB devices with encryption cannot be used. • Operation of all USB devices cannot be guaranteed. HDMI in HDMI HDMI out HDMI HDMI HDMI n Bluetooth® devices • Bluetooth devices that support A2DP can be used. Composite video connection • Operation of all Bluetooth devices cannot be guaranteed. VIDEO in File formats VIDEO n USB • The unit supports WAV (PCM format only), MP3, WMA and MPEG-4 AAC files (1- or 2-channel audio only). • The unit is compatible with sampling rate of up to 48 kHz. • Digital Rights Management (DRM) contents cannot be played back. 79 En VIDEO VIDEO out VIDEO VIDEO Information on HDMI (Example) The additional information on HDMI is as follows. HDMI Control HDMI Control HDMI Control allows you to operate external devices via HDMI. If you connect a TV that supports HDMI Control to the unit with an HDMI cable, you can control the unit (such as power and volume) with TV remote control operations. You can also control playback devices (such as HDMI Control-compatible BD/DVD players) connected to the unit with an HDMI cable. Playback starts Press SCENE (BD/DVD) Turns on and displays video from the playback device To use HDMI Control, you need to perform the following HDMI Control link setup after connecting the TV and playback devices. n Operations available from the TV’s remote control For details on settings and operating your TV, refer to the instruction manual for the TV. • Standby synchronization Note • Volume control including mute This setup is required every time you add a new HDMI Control-compatible device to your system. • Switching to input audio from the TV when the TV input is switched to its built-in tuner 1 2 • Switching to input video/audio from the selected playback device • Switching between audio output devices (the unit or TV speaker) (Example) HDMI Control HDMI Control HDMI Control Turn on the unit, TV, and playback devices. Configure the settings of the unit. 1 2 Switch the TV input to display video from the unit. Press SETUP. SLEEP SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS MUTE SETUP PROGRAM Playback device also turns off The unit turns off (standby) FM/AM SETUP USB INPUT OPTION VOLUME BLUETOOTH Turn off the TV MUTE SETUP Cursor keys ENTER OPTION ENTER ENTER n Operations available from the unit’s remote control RETURN TOP MENU DISPLAY HOME POP-UP/MENU RETURN RED GREEN YELLOW DISPLAYY DISPLA BLUE MEMORY TUNING • Starting playback on the playback device and turning on the TV with a scene selection (p.31) TUNING PRESET • Switching the TV input to display the “Setup” menu (when SETUP is pressed) • Controlling the playback device (playback and menu operations) 80 En TOP MENU HOME POP-UP/MENU 3 8 Use the cursor keys to select “HDMI” and press ENTER. Check that the unit is properly synchronized with the TV by turning off the TV or adjusting the TV volume with the TV remote control. Note ▪ If HDMI Control does not work properly, the problem may be solved by turning the playback device off and on again, or by unplugging the power plug and plugging it in again. Also, HDMI Control may not work properly if the number of connected devices exceeds the limit. In this case, disable HDMI Control on devices not in use. ▪ If the unit is not synchronized to the TV’s power operations, check the priority of the audio output setting on the TV. ▪ If you reconnect the HDMI cable, perform the procedure 5-8 again. ▪ We recommend using TV and playback devices from the same manufacturer so that HDMI Control works more effectively. 4 5 6 3 4 5 6 7 Use the cursor keys (q/w) to select “HDMI Control” and the cursor keys (e/r) to select “On” as shown below. If you made a digital optical cable connection between the TV and the unit, use the cursor keys (q/w) to select “TV Audio Input” and the cursor keys (e/r) to select “AUDIO1”. Press SETUP. Enable HDMI Control on the TV and playback devices (such as HDMI Control-compatible BD/DVD players). Turn off the main power of the TV and then turn off the unit and playback devices. Turn on the unit and playback devices and then turn on the TV. Switch the TV input to display the video from the unit. Check the followings. On the unit: The input to which the playback device is connected is selected. If not, select the input source manually. On the TV: The video from the playback device is displayed. 81 En Audio Return Channel (ARC) HDMI signal compatibility ARC allows you to input TV audio to the unit with the HDMI cable which transmits video signal to the TV. • When CPPM copy-protected DVD-Audio is played back, video/audio signals may not be output, depending on the type of the DVD player. Check the following after the HDMI Control settings. • The unit is not compatible with HDCP-incompatible HDMI or DVI devices. For details, refer to the instruction manual for each device. 1 2 Select a TV program with the TV remote control. • To decode audio bitstream signals on the unit, set the input source device appropriately so that the device outputs the bitstream audio signals directly (does not decode the bitstream signals on the playback device). For details, refer to the instruction manual for the playback device. Check that the input source of the unit will be automatically switched to “AV 2” and the TV audio will be played back on the unit. If you cannot hear the TV audio, check the following: ▪ “ARC” (p.58) in the “Setup” menu is set to “On”. ▪ The HDMI cable is connected to the ARC-compatible HDMI jack (HDMI jack marked “ARC”) on the TV. Some HDMI jack on the TV is not compatible with ARC. For details, refer to the instruction manual for the TV. Note ▪ If the audio is interrupted while using ARC, set “ARC” (p.58) in the “Setup” menu to “Off” and use a digital optical cable to input TV audio to the unit (p.19). ▪ When using ARC, connect a TV with an HDMI cable that supports ARC. ▪ “AV 2” is set as TV audio input at the factory. If you have connected any external device to the AV 2 jacks, use “TV Audio Input” (p.57) in the “Setup” menu to change the TV audio input assignment. To use the SCENE function (p.31), you also need to change the input assignment for SCENE (TV). 82 En Trademarks The trademarks used in this manual are as follows. Google Noto Fonts This product uses the following fonts. Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, DTS-HD, the Symbol, & DTS and the Symbol together are registered trademarks of DTS, Inc. © DTS, Inc. All Rights Reserved. Copyright © June 2015, Google (https://www.google.com/get/noto/#sans-lgc), with Reserved Font Name Noto Sans Version 1.004. Copyright © June 2015, Google (https://www.google.com/get/noto/help/cjk/), with Reserved Font Name Noto Sans CJK Version 1.004. This Font Software is licensed under the SIL Open Font License, Version1.1. This license is available with a FAQ at: http://scripts.sil.org/OFL The terms HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. x.v.Color™ “x.v.Color” is a trademark of Sony Corporation. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Yamaha Corporation is under license. App Store is a service mark of Apple Inc. Android™ is a trademark of Google Inc. “SILENT CINEMA” is a trademark of Yamaha Corporation. 83 En Specifications The specifications of this unit are as follows. HDMI Input jacks HDMI Features: • 4K UltraHD Video (include 4K/60, 50Hz 10/12bit), 3D Video, ARC (Audio Return Channel), HDMI Control (CEC), Auto Lip Sync, Deep Color, “x.v.Color”, HD audio playback, 21:9 Aspect Ratio, BT.2020 Colorimetry, HDR Compatible Analog Audio • Audio x 3 Video Format (Repeater Mode) • VGA • 480i/60 Hz • 576i/50 Hz • 480p/60 Hz • 576p/50 Hz • 720p/60 Hz, 50 Hz • 1080i/60 Hz, 50 Hz • 1080p/60 Hz, 50 Hz, 30 Hz, 25 Hz, 24 Hz • 4K/60Hz, 50Hz, 30 Hz, 25 Hz, 24 Hz Digital Audio (Supported frequencies: 32 kHz to 96 kHz) • Optical x 1 • Coaxial x 2 Video • Composite x 3 HDMI Input • HDMI x 4 Other jacks • USB x 1 (USB2.0) Audio Format • Dolby TrueHD • Dolby Digital Plus • Dolby Digital • DTS-HD Master Audio • DTS-HD High Resolution Audio • DTS Express • DTS • DSD 2-ch to 6-ch • PCM 2-ch to 8-ch (Max. 192 kHz/24-bit) Output jacks Analog Audio • Speaker Out x 5 (FRONT L/R, CENTER, SURROUND L/R) • Subwoofer Out x 1 • Headphone x 1 Video • Composite x 1 HDMI Output • HDMI OUT x 1 Content Protection: HDCP 2.2 compatible Link Function: CEC supported Other jacks TUNER YPAO MIC x 1 Analog Tuner • [U.K. and Europe models] FM/AM with Radio Data System x 1 (TUNER) • [Other models] FM/AM x 1 (TUNER) 84 En Audio Section USB Capable of Mass Storage Class USB Memory Rated Output Power (2-channel driven) Current Supply Capacity: 0.5 A • [U.S.A. and Canada models] (20 Hz to 20 kHz, 0.09% THD, 8 Ω) • [Other models] (20 Hz to 20 kHz, 0.09% THD, 6 Ω) – Front L/R Bluetooth 70 W+70 W • [U.S.A. and Canada models] (1 kHz, 0.9% THD, 8 Ω) Bluetooth version • Ver. 2.1+EDR – Front L/R – Center – Surround L/R Supported profile • A2DP 85 W+85 W 85 W 85 W+85 W Rated Output Power (1-channel driven) Supported codec • SBC • [U.S.A. and Canada models] (1 kHz, 0.9% THD, 8 Ω) • [Other models] (1 kHz, 0.9% THD, 6 Ω) Wireless output • Bluetooth Class 2 Radio Frequency (Operational Frequency) • 2402 MHz to 2480 MHz – Front L/R 100 W/ch – Center 100 W/ch – Surround L/R 100 W/ch Maximum Effective Output Power (1-channel driven) • [U.S.A. and Canada models] Maximum Output Power (E.I.R.P) • 4 dBm (2.51 mW) Maximum communication distance • 10 m (33 ft) without interference (1 kHz, 10% THD, 8 Ω) – Front L/R, Center, Surround L/R 130 W/ch (1 kHz, 10% THD, 6 Ω) – Front L/R, Center, Surround L/R 145 W/ch • [Other models] (1 kHz, 10% THD, 6 Ω) Compatible Decoding Formats – Front L/R, Center, Surround L/R Decoding Format • Dolby TrueHD, Dolby Digital Plus • Dolby Digital • DTS-HD Master Audio, DTS-HD High Resolution Audio, DTS Express • DTS, DTS 96/24 135 W/ch Dynamic Power (IHF) • [U.S.A. and Canada models] – Front L/R (8/6/4/2 Ω) 110/130/160/180 W • [Other models] Post Decoding Format • Dolby Pro Logic • Dolby Pro Logic II Music, Dolby Pro Logic II Movie, Dolby Pro Logic II Game • DTS Neo: 6 Music, DTS Neo: 6 Cinema – Front L/R (6/4/2 Ω) 110/130/150 W Damping Factor • Front L/R, 20 Hz to 20 kHz, 8 Ω 100 or more Input Sensitivity / Input Impedance • AV 2 etc. (1 kHz, 100 W/6 Ω) 200 mV/47 kΩ Maximum Input Signal • AV 2 etc. (1 kHz, 0.5% THD, Effect On) 85 En 2.3 V Output Level / Output Impedance • SUBWOOFER Video Maximum Input Level 1.5 Vp-p or more 1 V/1.2 kΩ Video Signal to Noise Ratio Headphone Jack Rated Output / Impedance • AV 2 etc. (1 kHz, 50 mV, 8 Ω) 50 dB or more 100 mV/470 Ω FM Section Frequency Response • AV 2 etc. to Front (10 Hz to 100 kHz) +0/-3 dB Tuning Range • [U.S.A. and Canada models] Signal to Noise Ratio (IHF-A Network) • AV 2 etc. (Input 1 kΩ Shorted, Speaker Out) • [Asia, Taiwan, Brazil and General models] 110 dB or more Residual Noise (IHF-A Network) • Front L/R (Speaker Out) 87.5 MHz to 107.9 MHz 87.5/87.50 MHz to 108.0/108.00 MHz • [U.K. and Europe models] 87.50 MHz to 108.00 MHz • [Other models] 87.50 MHz to 108.00 MHz 150 μV or less 50 dB Quiet Sensitivity (IHF, 1 kHz, 100% MOD.) Channel Separation • AV 2 etc. (Input 1 kΩ Shorted, 1 kHz/10 kHz) • Mono 3 μV (20.8 dBf) 70 dB/50 dB or more Signal to Noise Ratio (IHF) Volume Control • Range • Step MUTE, -80 dB to +16.5 dB • Mono 65 dB • Stereo 64 dB 0.5 dB Harmonic Distortion (IHF, 1 kHz) Tone Control Characteristics • Bass Boost/Cut • Bass Turnover • Treble Boost/Cut • Treble Turnover ±6 dB/0.5 dB Step at 50 Hz • Mono 0.5% • Stereo 0.6% 350 Hz Antenna Input ±6 dB/0.5 dB Step at 20 kHz 75 Ω unbalanced 3.5 kHz AM section Filter Characteristics (fc=40/60/80/90/100/110/120/160/200 Hz) • H.P.F. (Front, Center, Surround) 12 dB/oct. • L.P.F. (Subwoofer) 24 dB/oct. Tuning Range • [U.S.A. and Canada models] • [Asia, Taiwan, Brazil and General models] Video Section • [U.K. and Europe models] 531 kHz to 1611 kHz • [Other models] 531 kHz to 1611 kHz Video Signal Type • [U.S.A., Canada, Korea, Taiwan, Brazil and General models] • [Other models] NTSC PAL Video Signal Level • Composite 1 Vp-p/75 Ω 86 530 kHz to 1710 kHz 530/531 kHz to 1710/1611 kHz En General Power Supply • [U.S.A. and Canada models] • [Taiwan, Brazil and General models] AC 120 V, 60 Hz AC110 to 120/220 to 240 V, 50/60 Hz • [Korea model] AC 220 V, 60 Hz • [Australia model] AC 240 V, 50 Hz • [U.K. and Europe models] • [Asia model] AC 230 V, 50 Hz AC 220 to 240 V, 50/60 Hz Power Consumption 260 W Standby Power Consumption • HDMI Control Off – [Taiwan, Brazil and General models] 0.5 W – [Other models] 0.3 W • HDMI Control On (No Signals) 0.9 W • Bluetooth Standby ON 0.6 W • HDMI Control On, Bluetooth Standby ON 1.2 W Maximum Power Consumption • [Taiwan, Brazil and General models] 470 W Dimensions (W x H x D) 435 x 151 x 315 mm (17-1/8” x 6” x 12-3/8”) Weight 7.4 kg (16.3 lbs) * The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file. 87 En Yamaha Global Site http://www.yamaha.com/ Yamaha Downloads http://download.yamaha.com/ Manual Development Group © 2017 Yamaha Corporation Published 02/2017 NV-A0 YJ186A0/EN1
1 / 1

Yamaha RX-V383 El manual del propietario

Categoría
Receptores AV
Tipo
El manual del propietario