ROOMS TO GO 90242808 Assembly Instructions

Tipo
Assembly Instructions
4283-02 1.0
Assembly Instructions (English)
ASSEMBLY INSTRUCTION FOR
Oscar Floor Lamp
Model# 4283-02
353 West 39
th
Street, 2
nd
Floor, New York, NY 10018
Tel: (212) 736 4440 Fax: (212) 736 4806
www.adessohome.com
1. Screw pole (B) onto base (A) clockwise until tight.
2. Screw poles (B), (C), and (D) together.
3. Hex screw (F) comes pre-assembled to the tube.
Before placing the curved tube(E) onto the tube (D) ,
please unscrew this hex screw (F) to loosen.
4. Place curved tube (E) onto pole (D). Secure
connection by tightening tiny screws (F) with Allen
wrench (G).
Note: The lamp should face forward with the arm
reaching over the base. (see diagram bottom left)
GENERAL PRODUCT INFORMATION:
This product is suitable
for dry locations only.
---------------------------------------------------------------
IMPORTANT SAFETY INSTRUCTIONS:
This portable lamp has a polarized plug as a feature to
reduce the risk of electric shock (one blade is larger than
the other). This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified
electrician.Do not use with an extension cord unless the
plug can be fully inserted. DO NOT ALTER THE
PLUG .
-------------------------------------------------------
BULB TYPE: Use only with 1 type A Max 40W
bulb (not included).
PARTS DIAGRAM
(2) * Screw (F) (1)* Allen wrench (G)
4283-01 1.0
INSTRUCCIONES DE ENSAMBLAJE PARA
Oscar Lámpara de Piso
Modelo# 4283-01
353 West 39
th
Street, 2
nd
Floor, New York, NY 10018
Tel: (212) 736 4440 Fax: (212) 736 4806
www.adessohome.com
DIAGRAMA DE LAS PARTES
(2) * Tornillo Hexagonal (F) (1)* Llave Allen (G)
1. Enrosque el poste (B) hacia la derecha en la base
(A) hasta que quede apretado.
2. Enrosque los postes (B),(C) y (D) juntos.
3. El tornillo hexagonal (F) viene premontado en el
poste. Antes de colocar el poste curvo (E) en el poste
(D), desenrosque el tornillo hexagonal (F) para
aflojarlo.
4. Coloque el poste curvo (E) en el poste (D). Asegure
la conexión apretando los tornillos pequeños (F) con
la llave Allen (G).
Nota: La lámpara debe mirar hacia adelante con el
brazo sobre la base. (ver diagrama abajo a la
izquierda).
INFORMACION GENERAL DEL PRODUCTO:
Este producto es adecuado sólo
para lugares secos .
---------------------------------------------------------------
INSTRUCCIONES IMPORTANTES DE
SEGURIDAD :
Esta lámpara portátil tiene un enchufe polarizado (una
paleta es más ancha que la otra), función de seguridad que
reduce el riesgo de una descarga eléctrica. Este enchufe
encajará en un tomacorriente polarizado en un sólo sentido.
Si el enchufe no entra completamente en el tomacorriente,
invierta el enchufe. Si aún así no encaja, llame a un
electricista calificado. Nunca use un cable de extensión a
menos que el enchufe pueda insertarse por completo. NO
MODIFICAR EL ENCHUFE.
-------------------------------------------------------
TIPO DE BOMBILLA: Use solamente con una
bombilla tipo A de 40 vatios máximo (bombilla no
incluida).
  • Page 1 1
  • Page 2 2

ROOMS TO GO 90242808 Assembly Instructions

Tipo
Assembly Instructions

En otros idiomas