INSTALLATION INSTRUCTION
SLIM
WS-240818, WS-240824, WS-240836
WARNING
IMPORTANT: NEVER attempt any work without shutting off the electricity.
-
-
-
Read all instructions before installing.
System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. Go
to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
-
the circuit breaker switch(es) that control the power to the fixture or room that you are working on.
Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction could invalidate the ETL listing of this fixture.
CAUTION When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualifié en onformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL du luminaire.
MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer depression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación
de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calificad , de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación
ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calificación
ETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Aug.2023
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Manufacturing Facility
1700 South J Elmer Freeway
Suite 100
Cedar Hill, TX75104
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
1
South East Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture, including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
INSTALLATION
Install the provided mounting plate to the junction box using the junction box screws provided (1).
4.
5.
6.
7.
FIG. 1
Provide electrical service according to the “National Electrical Code” or your local electrical code to the outlet box.
Connect supply wires to fixture wires and insulate with supplied wire nuts (2) (FIG. 3):
Connect incoming ground wire to mounting plate ground wire
(green or bare.
Connect incoming common wire to fixture common (white.
Connect incoming hot wire to fixture black wire.
Select the desired fixture color temperature by setting the sliding switch
on the side of the canopy to the target CCT.
Raise the fixture to the junction box until the fixture screw holes are lined
up with the screw holes on the mounting plate.
Secure the fixture to the mounting plate using the fixture screws
provided (3).
3.
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Aug.2023
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Manufacturing Facility
1700 South J Elmer Freeway
Suite 100
Cedar Hill, TX75104
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
2
South East Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
INSTALLATION INSTRUCTION
SLIM
WS-240818, WS-240824, WS-240836
2
1
3
FIG. 2
2700K
3000K
3500K
4000K
5000K
8.
FIG. 3
-
1
-
2
WAC Lighting WS-240818 Instrucciones de operación
- Tipo
- Instrucciones de operación
En otros idiomas
Documentos relacionados
Otros documentos
-
Modern Forms FM-16818 Metropolis Instrucciones de operación
-
-
-
-
-