WAC Lighting WS-90636 Guía de instalación
- Tipo
- Guía de instalación
1WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
906 - LED Bath
WS-90627, WS-90636
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
HARDWARE
Wire
Connector
Qty: 3 pcs
+1 Extra
7EAC112201
Junction
Box Screw
Qty: 2 pcs
+1 Extra
7MPF0820C1
Mounting
Screw
Qty: 1 Extra
7MPF0408C1
Mounting
Screw
Qty: 1 Extra
7MPF0409S3
Wood
Screw
Qty: 2 pcs
+1 Extra
7MPF2204J2
Plastic
Anchor
Qty: 2 pcs
+1 Extra
7TDD082401
Assembly
Screw
Qty: 2 pcs
7MPF0820C1
Conversion
Plate
Qty: 1 pc
4MBA151110BA
Mounting
Ring
Qty: 1 pc
7MBC101501
Spacer
Qty: 2 pcs
7MBD076401
A1 B1 C1 D1 E1 F1 G1 H1 I1 J1
GND
2WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
906 - LED Bath
WS-90627, WS-90636
Back Plate Dimensions WS-90627 17 3/4”
WS-90636 29 3/4”
3 1/4”
2 3/4”
2 1/4”
WS-90627 25 3/4”
WS-90636 34 3/4”
Spacer
Junction Box
Mounting Plate
Assembly Screw
Wood Screw
Plastic Anchor
Conversion Plate
Junction Box Screw
Mounting Ring
Wire Connector
J1
G1
E1
F1
H1
B1
I1
A1
Wire Connector
Mounting Screw
Mounting Screw
Fixture
Bent Glass
WS-90627: (RPL-GLA-90627)
WS-90636: (RPL-GLA-90636)
Side Cap
Switch Box
Mounting Plate
Wood Screw
Junction Box Screw
Plastic Anchor Ground
Wire Screw A1
C1
D1
E1
B1
F1
FIG.1 MOUNT ON SWITCH BOX
FIG.2 MOUNT ON JUNCTION BOX
3WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
906 - LED Bath
WS-90627, WS-90636
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 3 Wiring
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
INSTALLATION
MOUNT ON SWITCH BOX (Fig. 1)
3. Remove the mounting screw (D1) and the mounting plate.
4. Remove the mounting screw (C1) and the side cap.
5. Place the bent glass onto the xture, and then secure it with side cap using mounting screw (C1).
6. Drill holes in the wall aligned the key holes located in the mounting plate; insert the plastic anchor (F1).
7. Secure the mounting plate to the switch box using junction box screws (B1), fasten it using wood screw (E1), the side of the mounting back
plate marked “GND” must face out.
8. Connect the xture wires to switch box wires as shown in Fig. 3, making sure that all wire connectors (A1) are secured. If your outlet box
has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the
mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.
9. Secure the xture onto the mounting plate using mounting screw (D1).
OR
MOUNT ON JUNCTION BOX (Fig. 2)
3. Remove the mounting screw (D1) and the mounting plate.
4. Remove the mounting screw (C1) and the side cap.
5. Place the bent glass onto the xture, and then secure it with side cap using mounting screw (C1).
6. Drill holes in the wall aligned the key holes located in the mounting plate; insert the plastic anchor (F1).
7. Secure the mounting ring (I1) to the junction box using junction box screws (B1), the side of the mounting back plate marked
“GND” must face out.
8. Secure the mounting plate to conversion plate (H1) with assembly screw (G1).
9. Fasten the wood screw (E1) and the spacer (J1) to the plastic anchor (F1).
10. Connect the xture wires to junction box wires as shown in Fig. 3, making sure that all wire connectors (A1) are secured. If your outlet box
has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the
mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
11. Secure the xture onto the mounting plate using mounting screw (D1).
-
1
-
2
-
3
WAC Lighting WS-90636 Guía de instalación
- Tipo
- Guía de instalación
En otros idiomas
Documentos relacionados
Otros documentos
-
Modern Forms FM-16818 Metropolis Instrucciones de operación
-
-
-
-
-
-
-
-
-