DAS DASNET-RACK99-230-ETH Manual de usuario
- Tipo
- Manual de usuario
DASNET-RACK99-230-ETH
User's Manual
Antes de utilizar el equipo, lea la sección
“Precauciones de seguridad” de este manual.
Conserve este manual para futuras consultas.
Before operating the device, please read the
“Safety precautions” section of this manual.
Retain this manual for future reference.
DASnet
CONTENTS
6 - 8
9 - 10
INTRODUCTION
ANNEX II : DASnet cables
3
4
5
13
11 - 12
ANNEX I : Schematics
CONFIGURATIONS
SAFETY PRECAUTIONS
WARRANTY
DECLARATION OF CONFORMITY
Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual
3
Precauciones de Seguridad
Safety Precautions
Caja de distribución para DASnet / DASnet Splitter
DASNET-RACK99-230-ETH
Equipo diseñado para funcionar entre 15ºC y 45ºC con una
humedad relativa máxima del 95%, con un rango de ±10% de la
tensión nominal de alimentación indicada en la etiqueta.
Working temperature ranges from 15ºC to 45ºC with a relative
humidity of 95%, with ±10% of the rated main voltage value
indicated on the label.
No instale el aparato cerca de ninguna fuente de calor como
radiadores, estufas u otros aparatos que produzcan calor. Debe
instalarse siempre sin bloquear la libre circulación de aire por las
aletas del radiador.
Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus that produce heat.
The circulation of air through the heatsink must not be blocked.
No exponga este equipo a la lluvia o humedad sin el protector
de lluvia recomendado. No exponga el equipo a salpicaduras sin
el protector de lluvia recomendado, ni coloque sobre él objetos
que contengan líquidos, tales como vasos y botellas.
Do not expose this device to rain or moisture without the rain
protector supplied. Do not place any objects containing liquids,
such as bottles or glasses, on the top of the unit. Do not splash
liquids on the unit without the rain protector supplied.
Este símbolo indica que el presente producto no puede ser
tratado como residuo doméstico normal, sino que debe
entregarse en el correspondiente punto de recogida de equipos
eléctricos y electrónicos.
This symbol on the product indicates that this product should
not be treated as household waste. Instead it shall be handed
over to the appicable collection point for the recycling of
electrical and electronic equipment.
El cableado exterior conectado al equipo requiere de su
instalación por una persona instruida o el uso de cables flexibles
ya preparados.
The outer wiring connected to the device requires installation by
an instructed person or the use of a flexible cable already
prepared.
Si el aparato es conectado permanentemente, la instalación
eléctrica del edificio debe incorporar un interruptor multipolar con
separación de contacto de al menos 3mm en cada polo.
If the apparatus is connected permanently, the electrical system
of the building must incorporate a multipolar switch with a
separation of contact of at least 3mm in each pole.
Limpie con un paño seco. No use limpiadores con disolventes. Clean only with a dry cloth. Do not use any solvent based
cleaners.
No existen partes ajustables por el usuario en el interior de este
equipo. Cualquier operación de mantenimiento o reparación
debe ser realizada por personal cualificado. Es necesario el
servicio técnico cuando el equipo se haya dañado de alguna
forma, como que haya caído líquido o algún objeto en el interior
del aparato, haya sido expuesto a lluvia o humedad, no funcione
correctamente, haya recibido un golpe o su cable de red esté
dañado.
No user serviceable parts inside. Refer all servicing to qualified
service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally or has been dropped.
The exclamation point inside an equilateral triangle is intended to
alert the users to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the product. Heed all warnings. Follow all
instructions. Keep these instructions.
WARNING: This is a class A product. In a domestic environment
this product may cause radio interferences in which case the
user may be required to take adequate measures.
Use this product only in E1, E2, E3 or E4 environments
according to EN55103-2.
No desconecte la tierra en el conector de alimentación pues es
peligroso e ilegal. Equipo de Clase I. El producto debe ser
conectado a un enchufe con toma de tierra. Sólo use este
equipo con el cable de red de alimentación adecuado para su
país.
El signo del rayo con la punta de flecha, alerta contra la
presencia de voltajes peligrosos no aislados. Para reducir el
riesgo de choque eléctrico, no retire la cubierta.
Do not remove mains connector ground, it is dangerous and
illegal. Class I device. The product must be connected to a
mains socket outlet with protective earth connection. Only use
this equipment with an appropriate mains cord for your country.
The lightning and arrowhead symbol warns about the presence
of uninsulated dangerous voltage. To reduce the risk of electric
shock, do not remove the cover.
El signo de exclamación dentro de un triángulo indica la
existencia de importantes instrucciones de operación y
mantenimiento en la documentación que acompaña al producto.
Conserve y lea todas estas instrucciones. Siga las advertencias.
ATENCIÓN: Es un producto clase A, por lo que en entornos
domésticos puede causar radio-interferencias, en cuyo caso el
usuario tendrá que tomar las medidas oportunas.
De acuerdo con EN55103-2, usar el equipo sólo en entornos E1,
E2, E3 ó E4.
Para desconectar el dispositivo debe usar el enchufe.
Desconecte este aparato durante tormentas eléctricas,
terremotos o cuando no se vaya a emplear durante largos
periodos.
To disconnect the device, you should use the mains plug. Unplug
this apparatus during lightning storms, earthquakes or when
unused for long periods of time.
Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual
4
GARANTÍA
WARRANTY
Todos nuestros productos están garantizados por un periodo de 24
meses desde la fecha de compra.
Las garantías sólo serán válidas si son por un defecto de
fabricación y en ningún caso por un uso incorrecto del producto.
Las reparaciones en garantía pueden ser realizadas,
exclusivamente, por el fabricante o el servicio de asistencia técnica
autorizado.
Otros cargos como portes y seguros, son a cargo del comprador
en todos los casos.
Para solicitar reparación en garantía es imprescindible que el
producto no haya sido previamente manipulado e incluir una
fotocopia de la factura de compra.
All our products are warrantied against any manufacturing defect
for a period of 2 years from date of purchase.
The warranty excludes damage from incorrect use of the product.
All warranty repairs must be exclusively undertaken by the factory
or any of its authorised service centers.
To claim a warranty repair, do not open or intend to repair the
product.
Return the damaged unit, at shippers risk and freight prepaid, to
the nearest service center with a copy of the purchase invoice.
Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual
5
Y es conforme a las siguientes Normas Armonizadas Europeas:
In accordance with Harmonized European Norms:
l EN 60065:2014.- Audio, video and similar electronic apparatus. Safety
requirements.
l EN 55032:2012.- Electromagnetic compatibility of multimedia equipment.
Emission requirements.
l EN 55103-2:2009.- Electromagnetic compatibility. Product family
standard for audio, video, audio-visual and entertainment lighting control
apparatus for professional use. Part 2:Immunity.
l EN 50581:2012.- Technical documentation for the assessment of
electrical and electronic products with respect to the restriction of
hazardous substances.
Cumple con los objetivos esenciales de las Directivas:
Abide by essential objectives relating Directives:
l de Baja Tensión (Low Voltage Directive) 2014/35/UE
l de Compatibilidad Electromagnética (EMC) 2014/30/UE
l RoHS 2011/65/UE
l RAEE (WEEE) 2012/19/UE
DECLARACIÓN DE CONFORMIDAD
DECLARATION OF CONFORMITY
DAS Audio Group, S.L.
C/ Islas Baleares, 24 - 46988 - Pol. Fuente del Jarro - Valencia. España
(Spain).
Declara que DASNET-RACK99-230-ETH:
Declares that DASNET-RACK99-230-ETH:
Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual
6
DISTRO-RACKNET-32-9
I
FI40 30mA 4pol.
FI-Schalter
DASNET-MATRIX99-ETH
DASNET-RACK99-230-ETH
DASNET-PATCH-PW-9
DISTRO-RACKNET-32-9
I
FI40 30mA4pol.
FI-Schalter
A
D
B
C
E
230/115 V~
1
OUT
2
OUT
3
OUT
PH.1 PH.2 PH.3
1
OUT
1
OUT
2
OUT
2
OUT
3
OUT
3
OUT
MAX.16A
per OUT
L3
L2
L1
N
PE
L2
L3
L1
N
AUDIO IN
AUDIO / DASNET OUT
LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9
TERMINATION
RESISTOR
Matrix 9X9
POWER
ON
ON
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
1
3
2
PE
8U high rack
1U high panel
INTRODUCTION
The DASNET-RACK99-230-ETH, assembled in a 19", 8U high rack, is composed of three
elements: 1x DASNET-MATRIX99-ETH, 1x DASNET-PATCH-PW-9 and 1x DISTRO-RACKNET-32-9 (all
described in the following sections of this manual). Therefore it is a product derived from the
DASNET-RACK99-230, but with a different matrix. Knowing the needs required by the system in
terms of distribution of power, currents and supply voltages and electrical safety guidelines,
will be essential for a safe use of this rack.
Caution: Before connecting to the mains make sure that all electrical safety specifications
and guidelines are met, and that all the safety warnings have been given due attention.
The DISTRO-RACKNET-32-9 allows the distribution of power between the different equipment
that form the system in a simple and safe way, and consists of:
A.- Three phase connector type IEC60309 or cetac, 32A / 400V for the input.
B.- Three phase connector type IEC60309 or cetac, 32A / 400V for the output (looped with the input).
C.- Phase 1, Phase 2 , Phase 3 breakers (one per ouput; total 9 units). The breakers are 16A nominal
current (In), type C (max Peak current > 5In).
D.- Phase LEDS. Indicate power per phase.
E.- Schuko outputs. There are 3 outputs per phase. There is one Auxiliary output connected in
parallel to the output 1 of phase 1 (max. 10W).
Frontal View Rear View
Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual
7
DASNET-PATCH-PW-9
DASNET-MATRIX99-ETH
230/115 V~
1
OUT
2
OUT
3
OUT
PH.1 PH.2 PH.3
1
OUT
1
OUT
2
OUT
2
OUT
3
OUT
3
OUT
MAX.16A
per OUT
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
AUDIO OUT
100-230V~ 50/60Hz
10W
AC INPUT
AUDIO IN
AUDIO / DASNET OUT
LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9
TERMINATION
RESISTOR
Matrix 9X9
POWER
ON
ON
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
1
3
2
ETHERNET INPUT:
EtherCon type connector
POWER
ON
ETHERNET
INPUT
The DASNET-PATCH-PW-9 provides AC power up to 9 connected devices, in a simple and
safe manner, using Neutrik connectors type PowerCon True1. The information on the AC
voltage range of the power supply and the maximum current available for each output is
shown on the silkscreen.
LED indicates Phase has power
Neutrik PowerCon True1 connector
Voltage range and max. current per output
Outputs connected to Phase 1: L1 Outputs connected to Phase 2: L2 Outputs connected to Phase 3: L3
On the rear of DASNET-PATCH-PW-9, a total of 9 cables with schuko are located. Each one of
the cables with its corresponding schuko must be connected to each output of the DISTRO-
RACKNET-32-9. On the other hand, the Schuko Auxiliary output of this will serve to power the
DASNET-MATRIX99-ETH.
AUDIO IN:
Female XLR type connectors
RS-485 OUT:
Male XLR type connector
LED ON
Link switch for the inputs of the matrix
Switch to active termination resistor
AUDIO / DASNET OUT:
Neutrik EtherCon connectors
FRONT PANEL
The DASNET-MATRIX99-ETH distribution module routes 9 balanced audio channels and
DASnet monitoring data up to 9 “zones” or clusters with self-powered DAS Audio systems.
REAR PANEL
Neutrik PowerCon True1 connector
AUDIO OUT:
Male XLR type connectors
On the front panel of DASNET-MATRIX99-ETH we can view three connector types:
The first, AUDIO IN, female XLR type for 9 balanced audio inputs. The panel includes 8 link
switches for routing audio from inputs to outputs. By the use of the switches one unique audio
signal can be routed to all ethercon outputs (per example).
The second, AUDIO / DASNET OUT, Neutrik etherCon type to distribute audio and
monitoring data to the different groups of self powered cabinets, 9 DASnet output connectors.
Finally we have the output RS-485 connector, which allows us to join several matrix to form
a network with RS-485 protocol. Between the connectors the end-of-line switch is observed.
On the rear panel, using a power cable, the DASNET-MATRIX99-ETH will be connected to the
Schuko Auxiliary output of the DISTRO-RACKNET-32-9. This cable has a Neutrik connector type
PowerCon True1 at one end and an F type (CEE 7/7) plug at the other. In addition, we have 9
balanced audio outputs that are in parallel with the inputs.
Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual
Basic connection of DASNET-MATRIX99-ETH
There is a termination resistor which can be activated with a switch. It is recommendable to
engage it in the first and last matrix of the network to increase network stability.
With this system, ideal solution for touring, we can link a maximum number of 288 devices,
with a length of the DASnet data cable should higher than 1000 meters (counting both XLR
data cables and ecp_xx), through multiple DASNET-MATRIX99-ETH units and converting the data
transmission from ethernet to fiber optic. Note: always CAT5 cables for ethernet as a
minimum.
DASNET-MATRIX99-ETH needs a USB to RS-485 converter and a MOXA Nport 5150
converter, to convert data from RS-485 to ethernet. These converters can be provided by DAS
Audio. The converters have to be connected to the DASNET-MATRIX99-ETH using the
ETHERNET INPUT connector, on the rear panel.
AUDIO IN
AUDIO / DASNET OUT
LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9
TERMINATION
RESISTOR
Matrix 9X9
POWER
ON
ON
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
2
3
1
PUSH
1
3
2
POWER
ON
8
DASnet
Net 1
USB-RS485
MOXA
Nport 5150
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
AUDIO OUT
100-230V~ 50/60Hz
10W
AC INPUT
ETHERNET
INPUT
Internally, each DASNET-MATRIX99-ETH has an RS-485 repeater that is directly connected
after the RS-485 input. The repeater allows having larger distances of cabling in the network
and a much higher number of devices without loosing capabilities.
The DASNET-MATRIX99-ETH is an ideal solution for audio and monitoring data distribution in
self powered cabinets that include DASnet: AERO-20A, AERO-40A, UX-221A, UX-30A, UX-218A,
UX-218A-R, LX-218CA-NET, ROAD-12A-NET, ROAD-15A-NET, etc.
Example of input links
On the front panel, the DASNET-MATRIX99-ETH offers flexible routing with switches that allow
you to mount an audio input to several outputs. The nine audio inputs can be linked directly to
their corresponding ethercon outputs. In addition, a single audio input can be linked to all
ethercon outputs by using the switches.
That is, if you look at the figure below, we have linked the inputs 1 with 2 on one side and 2
with 3 on the other. With this, it is enough to enter audio through connector 1 to output that
signal through all the connected output connectors: 1, 2 and 3, both ethercon on the front,
and XLR on the rear.
With this system, we can send a signal to all the equipment (linking all the outputs with the
input 1) or create several zones with different signal sends.
Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual
9
CONFIGURATIONS
Fiber Optic Ethernet
Media Converter
optic fiber
MOXA
Nport 5150
MOXA
Nport 5150
EtherNet Switch
Nport 5150
ethernet
USB-RS485
AUDIO OUT
AUDIO OUT AUDIO OUT
AUDIO OUT AUDIO OUT
AUDIO OUT AUDIO OUT
AUDIO OUT AUDIO OUT
AUDIO IN
AUDIO / DASNET OUT
LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9
TERMINATION
RESISTOR
Matrix 9X9
POWER
ON
ON
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
AUDIO IN
AUDIO / DASNET OUT
LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9
TERMINATION
RESISTOR
Matrix 9X9
POWER
ON
ON
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
AUDIO IN
AUDIO / DASNET OUT
LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9
TERMINATION
RESISTOR
Matrix 9X9
POWER
ON
ON
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
AUDIO IN
AUDIO / DASNET OUT
LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9
TERMINATION
RESISTOR
Matrix 9X9
POWER
ON
ON
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
AUDIO IN
AUDIO / DASNET OUT
LINK 1&2 LINK 2&3 LINK 3&4 LINK 4&5 LINK 5&6 LINK 6&7 LINK 7&8 LINK 8&9
TERMINATION
RESISTOR
Matrix 9X9
POWER
ON
ON
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100
netLINK
10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100
netLINK
10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100
netLINK
10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100
netLINK
10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100
netLINK
10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100
netLINK
10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100
netLINK
10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100
netLINK
10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100
netLINK
10/100Base TX to 100Base-FX
Fast Ethernet Converter
HTB-1100
netLINK
DASnet
cable>1km - max 288 units
Fiber Optic Ethernet
Media Converter
The best solution for large installations is to
convert DASnet, which uses the RS-485
protocol, to Ethernet. Doing so reduces cable
costs, as well as the speed of monitoring
software, regardless of the distance and
number of connected devices. To convert
DASnet (RS-485) to Ethernet, Nport 5150
converters are used. DASNET-MATRIX99-ETH is
the ideal solution to be used in this type of
applications.
Through multiple DASNET-MATRIX99-ETH
units, the network can be split into two
networks if necessary (with a maximum of 144
devices each). Each network will have different
"zones", each of which contains slave matrix
units connected to the MOXA Nport 5150
master that controls different clusters. From
each DASnet Matrix 99 ethernet, several
groups of self-powered devices can be
controlled. DAS audio recommends a
maximum number of 144 devices per subnet
(NET1 and NET2).
If the installation involves long distances, it
is strongly recommended to convert the
DASnet data from the Ethernet protocol to
optical fiber as shown (image opposite side).
NET1: max 144 units
NET2: max 144 units
Nport 5150
As we have indicated the DASNET-RACK99-230-ETH allows a power distribution of up to 32Amp per
phase (three-phase). Every 3 outputs of the DISTRO-RACKNET-32-9 of power are connected to a single
phase. This means that of each group of 3 PowerCon True 1 connectors, the maximum available
current is 32A.
The user must always consider the power consumption of the equipment (specified at 1/3 of the
nominal power with pink noise) connected to each output and DO NOT exceed the limit of 32A for
each group of 3 PowerCon outputs.
Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual
10
With the system configurations, DAS Audio recommends the maximum number of
cabinets that can be connected depending on the model, the power consumption
and the total equipment used (see table below).
Label of DASNET-RACK99-230-ETH
Consumption
per unit
Mains
1,8A
230V
3,6A
115V
3A 6A
4,5A 9A
9A 18A
6,7A 13,4A
3A 6A
3,1A
1,7A
1,7A
6,2A
3,4A
3,4A
No te: Consumption measured at 1/3 o f n om in al po we r w ith pink noise.
( 1) Mode ls : ROAD-12ART-NET230, ROAD-12ALT-NET230, ROAD-12ART-NET115, ROAD-12ALT-NET115
(2) Models: ROAD-15ART-NET230, ROAD-15ALT-NET230, ROAD-15ART-NET115, ROAD-15ALT-NET115
AERO-20A
AERO-40A
UX-218A
UX-221A
UX-30A
LX-118A
LX-218CA-NET
(1)
ROAD-12A-NET
(2)
ROAD-15A-NET
S/N
3/N/PE
400/230 V
50Hz/60Hz
Rated Current: 32A
Rated Voltage:
IP rating: IP20
www.dasaudio.com
MODEL: DASNET-RACK99-230-ETH
DAS Audio Group, S.L. (Valencia) MADE IN SPAIN
Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual
11
DISTRO-RACKNET-32-9
_ _
____
_ _ _
_ _ _
_
_ _ _
_ _
_
_
_
_
_
_
_ _
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
PC 230V 16A
L1 L3L2
N L2L1 L3 N L2L1 L3
40A/30mA
RCD
PC 230V 16A PC 230V 16A PC 230V 16A PC 230V 16A PC 230V 16A PC 230V 16A PC 230V 16A PC 230V 16APC 230V 16A
PH3.1 PH3.2 PH3.3PH2.3PH2.2PH2.1PH1.3PH1.2PH1.1AUX
OUT (Looped)IN
ANNEX I : Schematics
Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual
12
1.0
Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual
13
ANNEX II : DASnet cables
1 Orange-White Audio+ 2
2 Orange Audio- 3
3 Green-White Audio Earth 1
4 Blue
5 Blue-White
6 Green Data Earth 1
7 Brown-White Data- (A) 3
8 Brown Data+ (B) 2
etherCon XLR
It is very important to use the system with the intended cables to prevent electromagnetic
interferences between the analog audio signal, the DASnet data and the power. Be sure to
check the specifications provided by the cable manufacturer. It is also especially important
when installing connectors yourself, to note that when termination is not accurate, a cable
will be unable to achieve its maximum performance and could have interferences.
There are 4 different types of cables.
- The main feeds which include power and a STP, CAT7 cable. These cables are named
eCP_xx (xx refers to cable length).
- Power Links between cabinets.Cable code Plink1_09
- Links for RoadNet series. Power+STP CAT7. eCPk_1/eCPk_5
- The links between cabinets (aero40A/Convert15A/LX-218CAnet), which are STP CAT7
cables. Cable code eC_09
The main feed cable eCP_xx has the following structure:
AL Shield
2 2
ecP_xx: Power cable 3x2.5mm + CAT7 4x (2 x 0.14mm )
Jacket
Jacket
STP CAT 7 cable with Aluminium
Shield for each individual pair
and a main aluminium Shield.
The main Shield has to be
soldered to the etherCon
housing.
The eC_09 cable is a CAT5e
cable with global Aluminium
Shield.
Important
The pin out of the EtherCon to XLR is the following on the eCP cables:
Manual del Usuario / DASNET-RACK99-230-ETH / User’s Manual
UM_RACK99_04_EN
www.dasaudio.com
DAS Audio of America, INC.
6900 NW 52th Street
Miami, FL. 33166 - U.S.A.
TOLL FREE: 1 888 DAS 4 USA
DAS Audio Asia PTE. LTD.
3 Temasek Avenue, Centennial
Tower #34-36
Singapore 039190
Tel. +65 6549 7760
DAS Audio Group, S.L.
C/. Islas Baleares, 24
46988 Fuente del Jarro
Valencia, SPAIN
Tel. +34 96 134 0860
DAS do Brasil LTDA.
Rua Dos Andradas, 382 SL
Santa Efigênia, São Paulo
Brasil. CEP: 01208-000
Tel. +551133330764
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
