Pioneer DEH-P7100BT Guía de instalación

Categoría
Micrófonos
Tipo
Guía de instalación
Page 2 Page 3 Page 4
9
a
b
Fig. 5
Abb. 5
Afb. 5
Fig. 6
Abb. 6
Afb. 6
Fig. 8
Abb. 8
Afb. 8
Fig. 7
Abb. 7
Afb. 7
10cm
10cm
1
2
3
Fig. 1
Abb. 1
Afb. 1
Fig. 2
Abb. 2
Afb. 2
Fig. 3
Abb. 3
Afb. 3
Fig. 4
Abb. 4
Afb. 4
<KOMZX>  <08L00000>
Printed in Thailand 
Imprimé en Thaïlande
<0G020029A/N> EW
Installation Manual
Manual de instalación
Installationsanleitung
Manuel d’installation
Manuale d’installazione
Installatiehandleiding
Руководство по установке
CD RDS RECEIVER
REPRODUCTOR DE CD CON RECEPTOR RDS
CD RDS-EMPFÄNGER
AUTORADIO CD RDS
SINTOLETTORE CD RDS
CD RDS-ONTVANGER
CD RDS ПРИЕМНИК
DEH-P7100BT
Page 5 Page 6 Page 7 Page 8
Installation English
Note
Check all connections and systems before final
installation.
Do not use unauthorized parts. The use of
unauthorized parts may cause malfunctions.
Consult with your dealer if installation requires drilling
of holes or other modifications of the vehicle.
Do not install this unit where:
it may interfere with operation of the vehicle.
it may cause injury to a passenger as a result of a
sudden stop.
The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places such
as near the heater outlet.
Optimum performance is obtained when the unit is
installed at an angle of less than 60°. (Fig. 1)
When installing, to ensure proper heat dispersal when
using this unit, make sure you leave ample space
behind the rear panel and wrap any loose cables so
they are not blocking the vents. (Fig. 2)
1 Leave ample space
2 Dashboard
The cords must not cover up the area shown in the
figure. This is necessary to allow the amplifires to
radiate freely. (Fig. 3)
3 Do not cover this area.
DIN Front/Rear-mount
This unit can be properly installed either from
“Front” (conventional DIN Front-mount) or
“Rear” (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit
chassis). For details, refer to the following
installation methods.
Removing or attaching
the trim ring
1.
Extend top and bottom of the trim
ring outwards to remove the trim ring.
(Fig. 4)
When reattaching the trim ring, push the trim
ring onto the unit until it clicks. (If the trim ring
is attached upside down, the trim ring will not fit
properly.)
It
becomes easy to remove the trim ring if the
front panel is released.
4 Trim ring
DIN Front-mount
Installation with the rubber bush
1. Insert the mounting sleeve into the
dashboard.
When installing in a shallow space, use a
supplied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.
2. Secure the mounting sleeve by using
a screwdriver to bend the metal tabs
(90°) into place.
3.
Install the unit as illustrated. (Fig. 5)
5 Dashboard
6 Mounting sleeve
7 Rubber bush
8 Screw
Removing the Unit
1. Insert the supplied extraction keys
into both sides of the unit until they
click into place.
(Fig. 6)
2. Pull the unit out of the dashboard.
DIN Rear mount
1. Determine the appropriate position
where the holes on the bracket and
the side of the unit match.
(Fig. 7)
2. Tighten two screws on each side.
(Fig. 8)
Use either truss screws (5 mm × 8 mm) or flush
surface screws (5 mm × 9 mm), depending on
the shape of screw holes in the bracket.
9 Screw
a Factory radio mounting bracket
b Dashboard or Console
Fastening the front panel
If you do not plan to detach the front panel,
the front panel can be fastened with supplied
screws and holders.
1. Attach the holders to both sides of the
front panel. (Fig. 9)
c Holder
2. Replace the front panel to the unit.
(Fig. 10)
3.
Flip the holders into upright
positions. (Fig. 11)
4.
Fix the front panel to the unit using
screws. (Fig. 12)
d Screw
Nota
Verifique todas las conexiones y sistemas antes de la
instalación final.
No utilice piezas no autorizadas. El uso de piezas no
autorizadas puede causar un fallo de funcionamiento.
Consulte su r
evendedor si se requiere taladrar agujeros
o hacer otras modificaciones del vehículo para la
instalación.
No instale esta unidad donde:
pueda interferir con la operación del vehículo.
pueda causar lesiones a un pasajero en el caso de
una parada brusca.
El láser semiconductor se dañará si se sobr
ecalienta.
Instale esta unidad alejada de lugares calientes como
cerca de la salida del calentador.
Se obtiene el r
endimiento óptimo cuando se instala la
unidad en un ángulo inferior a 60°. (Fig. 1)
Cuando instale, para asegurar la dispersión apropiada
del calor durante el uso de esta unidad, asegúrese de
dejar un amplio espacio por detrás del panel trasero
y enrolle cualesquiera cables sueltos de modo que no
bloqueen las aberturas de ventilación. (Fig. 2)
1 Deje un amplio espacio
2 Tablero de instrumentos
Los cordones no deben tapar el área mostrado en
la figura. Esto es necesario para permitir que los
amplificadores puedan radiar libremente. (Fig. 3)
3 No cubra esta área.
Montaje delantero/trasero DIN
Se puede instalar esta unidad apropiadamente
mediante el montaje “delantero” (montaje
delantero DIN convencional) o montaje
“trasero” (montaje trasero DIN utilizando
los agujeros de tornillo roscados en los lados
del bastidor de la unidad). Para los detalles,
consulte los siguientes métodos de instalación.
Extracción o instalación del
anillo compensación
1. Extienda las partes superior e
inferior del anillo de compensación
hacia fuera para extraer el anillo de
compensación. (Fig. 4)
Cuando reinstale el anillo de compensación,
empuje el anillo de compensación en la unidad
hasta que encaje con un “clic”. (Si se instala
el anillo de compensación invertido, puede
que el anillo de compensación no se encaje
correctamente.)
Se hace más fácil quitar el anillo de
compensación si se suelta el panel delantero.
4 Anillo de compensación
Montaje delantero DIN
Instalación con el buje de caucho
1. Inserte el manguito de montaje en el
tablero de instrumentos.
Cuando instale en un lugar poco profundo, utilice
el manguito de montaje suministrado. Si hay
espacio suficiente detrás de la unidad, utilice el
manguito de montaje suministrado de fábrica.
2. Fije el manguito de montaje utilizando
un destornillador para doblar las
lengüetas de metal (90°) en posición.
3.
Instale la unidad como se muestra.
(Fig. 5)
5 Tablero de instrumentos
6 Manguito de montaje
7
Buje de caucho
8 Tornillo
Extracción de la unidad
1. Inserte las llaves de extracción
suministradas en ambos lados de la
unidad hasta que se enganchen en
posición.
(Fig. 6)
2. Tire de la unidad del tablero de
instrumentos.
Montaje trasero DIN
1. Determine la posicn apropiada
donde los agujeros en la ménsula y el
lado de la unidad se emparejan.
(Fig. 7)
2. Apriete los dos tornillos en cada lado.
(Fig. 8)
Utilice tornillos con cabeza ovalada (5 mm ×
8 mm) o tornillos de cabeza embutida (5 mm
× 9 mm), dependiendo de la forma de los
agujeros de tornillo en la ménsula.
9 Tornillo
a Ménsula de montaje de radio de fábrica
b Tablero de instrumentos o consola
Fijación del panel delantero
Si no planea extraer el panel delantero, se
puede fijar el panel delantero con los tornillos y
sujetadores suministrados.
1. Coloque los sujetadores en ambos
lados del panel delantero. (Fig. 9)
c Sujetador
2. Reinstale el panel delantero en la
unidad. (Fig. 10)
3.
Mueva los sujetadores en las
posiciones verticales. (Fig. 11)
4.
Fije el panel delantero a la unidad
utilizando los tornillos. (Fig. 12)
d Tornillo
Hinweise
Überprüfen Sie alle Anschlüsse und Systeme, bevor Sie
das Gerät endgültig einbauen.
Verwenden Sie keine unautorisierten Teile. Die
Verwendung von unautorisierten Teilen kann zu
Funktionsstörungen führen.
Wenden Sie sich an Ihren Fachhändler, wenn zum
Einbau des Geräts Löcher gebohrt oder andere
Veränderungen an Ihrem Auto
vorgenommen wenden müssen.
Bauen Sie das Gerät nicht an einer Stelle ein, wo:
es den Fahrer beim Fahren behindert.
es den Beifahrer bei plötzlichem Bremsen
verletzen kann.
Der Halbleiterlaser wird bei Überhitzung beschädigt.
Bauen Sie das Gerät daher nicht an einer Stelle
ein, wo es heiß wird, z. B. in der Nähe einer
Heizungsauslassöffnung.
Die optimale Leistung wird erzielt, wenn der
Einbauwinkel nicht mehr als 60° beträgt. (Abb. 1)
Damit die bei Betrieb dieses Geräts entwickelte Wärme
richtig abgeleitet werden kann, sorgen Sie beim Einbau
dafür, dass ausreichend Platz hinter der Rückwand
bleibt, und wickeln Sie lockere Kabel so, dass diese
keine Öffnungen blockieren können. (Abb. 2)
1 Reichlich Platz lassen
2 Armaturenbrett
Die Leitungen rfen den in der Abbildung gezeigten
Bereich nicht verdecken. Dies ist erforderlich, damit die
Verstärker frei Wärme abstrahlen können. (Abb. 3)
3 Diesen Bereich nicht verdecken.
DIN Einbau an der
Vorderseite/Rückseite
Dieses Gerät kann entweder an der
“Vorderseite” (herkömmliche DIN Einbau an
der Vorderseite) oder an der “Rückseite” (DIN
Einbau an der Rückseite mit Hilfe der Löcher
für die Gewindeschrauben, die sich an der
Seite des Geräte-Chassis befinden) eingebaut
werden. Einzelheiten entnehmen Sie bitte den
folgenden Einbaumethoden.
Abnehmen und Anbringen des
Zierleistenrings
1. Ziehen Sie den Zierleistenring an der
Ober- und Unterseite nach außen, um
den Ring zu entfernen. (Abb. 4)
Beim erneuten Anbringen des Zierleistenrings
drücken Sie den Ring auf das Gerät, bis er
einrastet. (Falls der Zierleistenring verkehrt herum
angebracht wird, passt er nicht richtig.)
W
enn die Frontplatte freigegeben ist, ist es ganz
einfach, den Zierleistenring abzunehmen.
4 Zierleistenring
DIN Einbau an der Vorderseite
Einbau mit der Gummibuchse
1. Setzen Sie den Halter in das
Armaturenbrett ein.
Verwenden Sie beim Einbau an einer engen Stelle
einen mitgelieferten Halter. Wenn nicht genügend
Platz hinter dem Gerät vorhanden ist, verwenden
Sie den vom Werk mitgelieferten Halter.
2. Befestigen Sie den Halter mit Hilfe
eines Schraubendrehers, um die
Metalllaschen um 90° zu verbiegen.
3.
Bauen Sie das Gerät wie gezeigt ein.
(Abb. 5)
5 Armaturenbrett
6 Halter
7 Gummibuchse
8 Schraube
Ausbauen des Geräts
1. Setzen Sie die mitgelieferten
Ausziehschlüssel auf beiden Seiten
bis zur Einrastposition in das Gerät
ein.
(Abb. 6)
2. Ziehen Sie das Gerät aus dem
Armaturenbrett.
DIN Einbau an der Rückseite
1. Bestimmen Sie die geeignete
Position, wo die Löcher in der
Konsole und an der Geräteseite
übereinstimmen.
(Abb. 7)
2. Ziehen Sie zwei Schrauben auf jeder
Seite fest.
(Abb. 8)
Verwenden Sie entweder Flachrundkopfschrauben
(5 mm × 8 mm) oder Schrauben mit bündiger
Oberfläche (5 mm × 9 mm), je nach der Art der
Schraubenlöcher in der Konsole.
9 Schraube
a Vom Werk mitgelieferter
Radio-Befestigungsbügelavec la voiture
b Armaturenbrett oder Konsole
Befestigung der Frontplatte
Falls Sie nicht beabsichtigen, die Frontplatte
abzunehmen, kann sie mit den mitgelieferten
Schrauben und Haltern befestigt werden.
1. Bringen Sie die Halter an beiden
Seiten der Frontplatte an. (Abb. 9)
c Halter
2. Bringen Sie die Frontplatte weider
am Gerät an. (Abb. 10)
3
. Klappen Sie die Halter hoch. (Abb. 11)
4. Sichern Sie die Frontplatte mit den
Schrauben am Gerät. (Abb. 12)
d Schraube
Remarque
Vérifiez toutes les connexions et tous les systèmes
avant l’installation finale.
N’utilisez aucune pièce non autorisée. L
’utilisation
de pièces non autorisées peut causer un mauvais
fonctionnement.
Consultez votr
e revendeur si l’installation nécessite
que vous perciez des trous ou effectuiez d’autres
modifications du véhicule.
N’installez pas l’appar
eil dans un endroit où:
il peut gêner la conduite du véhicule.
il peut causer des blessures à un passager à la suite
d’un arrêt brutal.
Le laser à semi-conducteur sera endommagé en cas de
surchauffe. Installez cet appareil à l’écart des endroits
chauds tels que près de la sortie du chauffage.
Des performances optimales peuvent êtr
e obtenues
quand l’appareil est installé avec un angle de moins de
60°. (Fig. 1)
Lors de l’installation de l’appareil, laissez suffisamment
d’espace derrière le panneau arrière pour permettre
une dissipation correcte de la chaleur et pliez tout
câble gênant de façon qu’il n’obstrue pas les orifices
de ventilation. (Fig. 2)
1 Laissez suffisamment d’espace
2 Tableau de bord
Les cordons ne doivent pas couvrir la zone montrée
sur la figure. C’est nécessaire pour permettre à
l’amplificateur de rayonner librement. (Fig. 3)
3 Ne recouvrez pas cette zone.
Montage avant/arrière DIN
Cet appareil peut être installé correctement par
“l’avant” (montage avant conventionnel DIN)
ou par “l’arrière” (montage par l’arrière DIN,
en utilisant les trous taraudés de chaque côté
du châssis). Pour les détails, reportez-vous aux
méthodes d’installation suivantes.
Retrait ou fixation de la
garniture
1. Étendez la partie supérieure et
inférieure de la garniture vers
l’extérieur pour la retirer.
(Fig. 4)
Pour fixer de nouveau la garniture, poussez
la garniture sur l’appareil jusqu’à ce qu’elle
s’emboîte en produisant un bruit sec. (Si la
garniture est fixée à l’envers, elle ne s’emboîte
pas correctement.)
Il est plus facile de retirer la garniture quand le
panneau avant est détaché.
4 Garniture
Montage avant DIN
Installation avec l’amortisseur en
caoutchouc
1. Insérez le manchon de montage dans
le tableau de bord.
Si l’installation se fait dans un emplacement
étroit, utilisez le manchon de montage fourni.
S’il y a suffisamment de place derrière l’appareil,
utilisez le manchon de montage fourni avec la
voiture.
2. Fixez le manchon de montage en
utilisant un tournevis pour tordre les
languettes de métal (90°).
3.
Installez l’appareil comme montré
sur l’illustration. (Fig. 5)
5 Tableau de bord
6 Manchon de montage
7 Amortisseur en caoutchouc
8 Vis
Retrait de l’appareil
1. Inrez les clés d’extraction fournies
de chaque côté de l’appareil jusqu’à ce
que vous entendiez unclic.
(Fig. 6)
2. Tirez l’appareil pour le sortir du
tableau de bord.
Montage arrière DIN
1. Déterminez la position appropriée
dans laquelle les trous du support
de montage coïncident avec ceux du
côté de l’appareil.
(Fig. 7)
2. Serrez deux vis de chaque côté.
(Fig. 8)
Utilisez des vis à tête bombée (5 mm × 8 mm)
ou des vis à tête encastrée (5 mm × 9 mm), en
fonction de la forme des trous dans le support.
9 Vis
a Support de montage fourni avec la voiture
b Tableau de bord ou console
Fixation du panneau avant
Si vous ne prévoyez pas de détacher le
panneau avant, il peut être fixé avec les vis et
les crochets fournis.
1. Attachez les crochets des deux côtés
de la face avant. (Fig. 9)
c Crochet
2. Remettez la face avant en place sur
l’appareil. (Fig. 10)
3.
Faites pivoter les crochets en position
droite. (Fig. 11)
4.
Fixez la face avant sur l’appareil avec
les vis. (Fig. 12)
d Vis
Instalación Español Einbau Deutsch Installation Français
Page 9 Page 10 Page 11 Page 12
Installazione Italiano Installatie Nederlands
Установка Pyccкий
Opmerking
Controleer alle aansluitingen en systemen voor de
uiteindelijke installatie.
Gebruik geen ongeautoriseer
de onderdelen. Gebruik
van niet-goedgekeurde onderdelen kan leiden tot
storingen.
Raadpleeg uw dealer als u voor de installatie gaten
moet boren of andere wijzigingen aan het voertuig
zelf moet aanbrengen.
Installeer dit toestel in geen geval op een locatie waar:
het de besturing van het voertuig kan hinderen.
het een passagier zou kunnen verwonden bij een
noodstop.
De halfgeleider laser zal kapot gaan als deze oververhit
raakt. Installeer dit toestel niet in de buurt van zeer
warme plekken, zoals bij een verwarmingsrooster.
De optimale pr
estaties worden verkregen wanneer het
toestel geïnstalleerd wordt onder een hoek van minder
dan 60º. (Afb. 1)
Om verzekerd te kunnen zijn van voldoende ventilatie bij
gebruik van dit toestel, dient u er bij de installatie voor
te zorgen dat u achter het achterpaneel en rondom het
toestel voldoende ruimte vrij laat, en dient u eventuele
losse bedrading samen te bundelen zodat deze de
ventilatie-openingen niet kan blokkeren. (Afb. 2)
1 Laat voldoende ruimte vrij
2 Dashboard
Let erop dat de snoeren niet het gedeelte bedekken
dat is aangegeven in de afbeelding. Dit om te
voorkomen dat de ventilatie van de versterker wordt
belemmerd. (Afb. 3)
3 Deze plek niet afdekken.
DIN Voor/achter montage
Dit toestel kan op de juiste manier worden
vastgemaakt aan de voorkant (conventionele
DIN montage) of aan de achterkant
(DIN achtermontage, met behulp van de
schroefgaatjes aan de zijkanten van het chassis
van het toestel). Voor details verwijzen we u
naar de volgende installatiemethoden.
Verwijderen of bevestigen van
de afwerkingsrand.
1.
Buig de bovenkant en de onderkant
van de afwerkingsrand naar buiten
om deze te verwijderen. (Afb. 4)
Druk de afwerkingsrand op het toestel tot deze
vastklikt wanneer u de afwerkingsrand weer vast
maakt. (Als de afwerkingsrand ondersteboven
gehouden wordt, zal deze niet goed passen.)
De afwerkingsrand is makkelijker los te maken
wanneer het voorpaneel verwijderd is.
4 Afwerkingsrand
DIN Voor-montage
Installatie met het rubber tussenstuk
1. Steek de bevestigingskraag in het
dashboard.
Gebruik een andere bevestigingskraag bij
installatie op een relatief ondiepe locatie. Als
er genoeg ruimte achter het toestel is, kunt u
de standaard meegeleverde bevestigingskraag
gebruiken.
2. Zet de bevestigingskraag vast door
met behulp van een schroevendraaier
de metalen lipjes te verbuigen (90°).
3.
Installeer het toestel zoals u kunt
zien op de afbeelding. (Afb. 5)
5 Dashboard
6 Bevestigingskraag
7 Rubber tussenstuk
8 Schroef
Verwijderen van het toestel
1. Steek de meegeleverde
ontgrendelingsstrips in beide
zijkanten van het toestel tot deze
vastklikken.
(Afb. 6)
2. Trek het toestel uit het dashboard.
DIN Achter-montage
1. Bepaal welke gaatjes in de beugel
en in de zijkant van het toestel met
elkaar overeenkomen.
(Afb. 7)
2. Gebruik twee schroeven aan elke
kant.
(Afb. 8)
Gebruik schroeven met platte kop (5 mm × 8 mm)
of verzinkbare kop (5 mm × 9 mm), afhankelijk
van de vorm van de schroefgaatjes in de beugel.
9 Schroef
a Fabrieksmontagebeugel of-steun voor bevestiging
radio e.d.
b Dashboard of console
Vastzetten van het voorpaneel
Als u het voorpaneel niet wilt kunnen
verwijderen, kunt u het vastzetten met de
daartoe meegeleverde schroeven en houders.
1. Bevestig de houders aan beide zijden
van het voorpaneel. (Afb. 9)
c Houder
2. Plaats het voorpaneel weer op het
toestel. (Afb. 10)
3.
Klap de houders overeind. (Afb. 11)
4. Bevestig het voorpaneel met de
schroeven aan het toestel. (Afb. 12)
d Schroef
Примечание
Проверьте все соединения и системы перед
окончательной установкой.
Не используйте неразрешенные части.
Использование неразрешенных частей может стать
причиной неисправной работы.
Проконсультируйтесь с вашим дилером, если
установка требует просверливания отверстий или
других модификаций вашего транспортного средства.
Не устанавливайте устройство там, где:
оно может служить препятствием работы
транспортного средства.
оно может стать причиной повреждения
пассажира в результате внезапной остановки.
Полупроводниковый лазер будет поврежден, если
он перегреется. Устанавливайте данное устройство
вдали от горячих мест, таких как рядом с выпуском
нагревателя.
Оптимальное изображение не получается, когда
устройство установлено под углом меньше чем 60°.
(Рис. 1)
При установке, после подтверждения подходящего
рассеивания тепла при использовании этого
устройства, пожалуйста, удостоверьтесь, что вы
оставляете прострное место позади адней панели
и, пожалуйста, сверните любые неприкрепленные
кабели так, чтобы они не смогли заблокировать
вентиляционное отверстие. (Рис. 2)
1 Ост
авить просторное место
2 Пeрeдняя пане
ль
Провода не должны закрывать зоны, показанные на
рисунке. Это необходимо для свободного рассеивания
тепла, излучаемого усилителями. (Рис. 3)
3 Не закрыв
айте эту область.
Переднее/Заднеекрепление
постандартуDIN
Крепление данного устройства можно
выполнять как “спереди” (стандартное переднее
крепление DIN), так и “сзади” (заднее крепление
DIN с использованием резьбовых отверстий
для винтов, расположенных по бокам рамы
устройства). Более подробная информация
приведена ниже в иллюстрированном описании
методов установки.
Удалениеилиприкрепление
ластичногоободка
1. Оттянитеверхинизластичного
ободканаружу,чтобывытащить
его.
(Рис.4)
Когда повторно присоединяете ластичный
ободок, вдавите его в устройство, пока он не
щелкнет. (Если ластичный ободок присоединен
верхней стороной вниз, то он не будет подогнан
должным образом.)
Вытащить ластичный ободок легче, если
передняя панель опущена.
4 Ластичный ободок
Переднеекреплениепо
стандартуDIN
Установкасрезиновойвтулкой
1. Вставьтемонтажныйрукавв
переднююпанель.
Когда устанавливаете в неглубокое
пространство, используйте предусмотренный
монтажный рукав. Если позади устройства
имеется достаточное пространство, используйте
предусмотренный заводом монтажный рукав.
2. Закрепитемонтажныйрукав,
используяотвертку,чтобысогнуть
металлическиеушки(90°)на
место.
3.
Установитеустройствокак
показанонаиллюстрации.(Рис.5)
5 Передняя панель
6 Монт
ажный рукав
7 Р
езиновая втулка
8 Винт
УдалениеУстройства
1. Вставьтепредусмотренные
ключидляизвлечениявобе
стороныустройства,покаонине
защелкнутсянаместо.
(Рис.6)
2. Вытянитеустройствоизпередней
панели.
ЗаднеекреплениепостандартуDIN
1. Подберитеподходящееместо,
гдеотверстиянаскобеистороне
устройствабудутсовпадать.
(Рис.7)
2. Затянитедвавинтанакаждой
стороне.
(Рис.8)
Используйте винты со сферической головкой
(5 мм × 8 мм) или винты с потайной головкой (5
мм × 9 мм), в зависимости от формы отверстий в
скобе.
9 Винт
a Зав
одская скоба для крепления радиоприемника
b Пере
дняя панель или консоль
Закреплениепереднейпанели
Если вы не планируете отсоединять
переднюю панель, то она может быть
закреплена с помощью поставляемых винтов
и держателей.
1. Закрепитедержателисобеих
сторонпереднейпанели.(Рис.9)
c Держатель
2. Приложитепереднююпанельк
устройству.(Рис.10)
3. Перевернитедержателив
вертикальноеположение.(Рис.11)
4. Прикрепитепереднююпанельк
устройству,используявинты.ис.12)
d Винт
Nota
Prima dell’installazione finale vi raccomandiamo
di verificare tutti i sistemi coinvolti e le relative
connessioni.
Non fate mai uso di parti non autorizzate. Esse
potrebbero infatti dar luogo a malfunzionamenti.
Qualora l’installazione richieda l’esecuzione di fori
oppure di modifiche al veicolo, rivolgetevi innanzi tutto
al vostro rivenditore.
Non installate questa unità ove:
possa interferire con la guida del veicolo.
possa causare il ferimento dei passeggeri in caso
di brusca frenata.
I
l laser a semiconduttore si potrebbe danneggiare in caso
di surriscaldamento. Installate pertanto l’unilontano
dai punti ad elevata temperatura quali, ad esempio, gli
effusori del sistema di riscaldamento del veicolo.
Le pr
estazioni migliori si ottengono quando s’installa
l’unità secondo un angolo di ampiezza inferiore a 60°.
(Fig. 1)
Per assicurare un’adeguata dispersione del calore
dell’apparecchio nel corso del suo utilizzo, durante
l’installazione si raccomanda di lasciare ampio
spazio dietro il pannello posteriore e di avvolgere i
cavi allentati affinché non ostruiscano le bocche di
ventilazione. (Fig. 2)
1 Lasciare ampio spazio
2 Cruscotto
I cavi non devono coprire la zona mostrata nella figura:
l’amplificatore deve essere in grado di diffondere il
suono liberamente. (Fig. 3)
3 Non ostruire quest’area.
Installazione DIN frontale/
posteriore
L’unità può essere correttamente installata sia
su “frontalmente” (normale installazione DIN
frontale) sia “posteriormente” (installazione
DIN posteriore impiegando i fori filettati ubicati
sui lati del telaio). Le sezioni che seguono
offrono informazioni dettagliate sui due
metodi d’installazione.
Rimozione o applicazione del
bordo di rifinitura
1.
Tirate verso l’esterno le parti superiore
e inferiore del bordo di rifinitura in
modo da rimuoverlo. (Fig. 4)
Per rimontarlo premetelo nell’unità sino ad
avvertirne lo scatto in posizione (non s’inserisce
correttamente se si tenta di montarlo capovolto).
La rimozione del bor
do di rifinitura risulta più facile
quando si rimuove il pannello anteriore.
4 Bordo di rifinitura
Installazione DIN frontale
Installazione con la guaina di gomma
1. Inserite nel cruscotto il telaio
d’installazione.
Il telaio d’installazione va usato in caso
d’installazione in un punto poco profondo.
Qualora posteriormente all’unità vi sia sufficiente
spazio è raccomandabile impiegare il telaio
d’installazione del costruttore.
2. Fissate il telaio d’installazione
usando un cacciavite col quale
piegare in posizione (di 90°) le
linguette metalliche.
3.
Installate l’unità nel modo mostrato.
(Fig. 5)
5 Cruscotto
6 Telaio d’installazione
7 Guaina di gomma
8 Vite
Rimozione dell’unità
1. Inserite in entrami i lati dell’unità le
apposite chiavi di estrazione sino ad
avvertirne lo scatto in posizione.
(Fig. 6)
2. Estraete l’unità dal cruscotto.
Installazione DIN posteriore
1. Determinate il punto esatto in cui i
fori della staffa e quelli ubicati ai lati
dell’unità coincidono.
(Fig. 7)
2. Serrate bene due viti di entrambi i
lati.
(Fig. 8)
In funzione della forma dei fori filettati della staffa
usate viti a trave (5 mm × 8 mm) oppure viti
incassate (5 mm × 9 mm).
9 Vite
a Staffa di montaggio radio del costruttore
b Cruscotto o console centrale
Fissaggio del pannello anteriore
Qualora non intendiate separare il pannello
anteriore, esso può essere perennemente
fissato con le viti e i supporti forniti in
dotazione.
1. Assicurare i supporti di fissaggio ad
entrambi i lati del pannello anteriore.
(Fig. 9)
c Supporto
2. Rimontare il pannello anteriore
sull’unità. (Fig. 10)
3.
Ruotare i supporti nelle posizioni
vertiali. (Fig. 11)
4.
Bloccare il pannello anteriore all’unità
per mezzo delle apposite viti. (Fig. 12)
d Vite
Page 13 Page 14 Page 15 Page 16
B
Installing the microphone
Install the microphone in a position and
orientation that will enable it to pick up the
voice of the person operating the system.
CAUTION
It is extremely dangerous to allow the microphone
lead to become wound around the steering column
or gearstick. Be sure to install the unit in such a way
that it will not obstruct driving.
When installing the microphone
on the sun visor
1. Install the microphone on the
microphone clip. (Fig. 1)
1 Microphone
2
Microphone clip
2. Install the microphone clip on the
sun visor. (Fig. 2)
With the sun visor up, install the microphone
clip. (Lowering the sun visor reduces the voice
recognition rate.)
3
Microphone clip
4 Clamp
Use
separately sold clamps to secure the lead
where necessary inside the vehicle.
When installing the microphone
on the steering column
1. Install the microphone on the
microphone clip. (Fig. 3)
5 Microphone
6
Microphone base
7
Microphone clip
8
Fit the microphone lead into the groove.
Microphone can be installed without using
microphone clip. In this case, detach the
microphone base from the microphone clip. To
detach the microphone base from microphone
clip, slide the microphone base.
2. Install the microphone clip on the
steering column. (Fig. 4) (Fig. 5)
9 Double-sided tape
a
Install the microphone clip on the rear side of the
steering column.
b Clamp
Use
separately sold clamps to secure the lead
where necessary inside the vehicle.
Adjusting the microphone angle
(Fig. 6)
The microphone angle can be adjusted.
Installation English
Fig. 1
Abb. 1
Afb. 1
Рис.
1
Fig. 2
Abb. 2
Afb. 2
Рис.
2
Fig. 3
Abb. 3
Abb. 3
Рис.
3
Fig. 4
Abb. 4
Abb. 4
Рис.
4
Fig. 5
Abb. 5
Abb. 5
Рис.
5
Fig. 6
Abb. 6
Abb. 6
Рис.
6
Instalación Español
Instalación del micrófono
Instale el micrófono en una posición u
orientación que permita captar bien las voces
de la persona que utilice el sistema mediante
voz.
PRECAUCIÓN
Es peligrosísimo dejar que el cable del micrófono
se enrolle en la base del volante o en la palanca de
cambios. Asegúrese de instalar la unidad de forma
que ésta no sea un obstáculo para la conducción.
Cuando instale el micrófono en
la visera
1. Instale el micrófono en la presilla de
micrófono. (Fig. 1)
1 Micrófono
2
Presilla de micrófono
2. Instale la presilla de micrófono en la
visera. (Fig. 2)
Con la visera hacia arriba, instale la presilla
del micrófono. (Al bajar la visera se reduce la
capacidad de reconocimiento de mediante voz).
3
Presilla de micrófono
4 Abrazadera
Utilice
abrazaderas vendidas separadamente
para asegurar el cable en el interior del vehículo
donde sea necesario.
Cuando instale el micrófono en
la base del volante
1. Instale el micrófono en la presilla de
micrófono. (Fig. 3)
5 Micrófono
6Base
del micrófono
7
Presilla de micrófono
8
Fije el cable del micrófono en la ranura.
Se puede instalar el micrófono sin utilizar la
presilla de micrófono. En este caso, extraiga la
base del micrófono de la presilla de micrófono.
Para extraer la base del micrófono de la presilla
de micrófono, deslice la base del micrófono.
2. Instale la presilla de micrófono en la
base del volante. (Fig. 4) (Fig. 5)
9 Cinta con adhesivo de doble cara
a
Instale la presilla del micrófono en el lado trasero
de la base del volante.
b Abrazadera
Utilice
abrazaderas vendidas separadamente
para asegurar el cable en el interior del vehículo
donde sea necesario.
Ajuste del ángulo del micrófono
(Fig. 6)
Se puede ajustar el ángulo del micrófono.
Einbau des Mikrofons
Das Mikrofon an einem geeigneten Platz
anbringen und so ausrichten, dass es die
Stimme der Person, die das System über
Sprache steuert, gut aufnimmt.
VORSICHTSMASSNAHMEN
Es ist äußerst gefährlich, das Mikrofonkabel um die
Lenksäule oder den Gangschalthebel zu wickeln.
Beim Einbau unbedingt darauf achten, dass das
Gerät den Fahrer nicht behindert.
Befestigung des Mikrofons an
der Sonnenblende
1. Das Mikrofon im Mikrofonklemmhalter
befestigen. (Abb. 1)
1 Mikrofon
2 Mikrofonklemmhalter
2. Den Mikrofonklemmhalter an der
Sonnenblende anklemmen. (Abb. 2)
Die Sonnenblende hochklappen und den
Mikrofonklemmhalter anklemmen. (Ein Herunterklappen
der Sonnenblende verringert die Spracherkennungsrate bei
der sprachgesteuerten Bedienung).
3 Mikrofonklemmhalter
4 Kabelklemme
Das
Mikrofonkabel mit getrennt erhältlichen
Kabelklemmen im Fahrzeuginnenraum verlegen.
Befestigung des Mikrofons an
der Lenksäule
1. Das Mikrofon im Mikrofonklemmhalter
befestigen. (Abb. 3)
5 Mikrofon
6 Mikrofon-Unterlage
7 Mikrofonklemmhalter
8
Das Mikrofonkabel in die Kerbe einpassen.
Das Mikrofon kann ohne den
Mikrofonklemmhalter installiert werden.
Nehmen Sie die Mikrofon-Unterlage in diesem
Fall vom Mikrofonklemmhalter ab. Um die
Mikrofon-Unterlage vom Mikrofonklemmhalter
abzunehmen, verschieben Sie sie einfach.
2. Das Mikrofon an der Lenksäule
befestigen. (Abb. 4) (Abb. 5)
9 Doppelseitiger Klebestreifen
a
Den Mikrofonklemmhalter an der Rückseite der
Lenksäule befestigen.
b
Kabelklemme
Das Mikrofonkabel mit getrennt erhältlichen
Kabelklemmen im Fahrzeuginnenraum verlegen.
Einstellung des Mikrofonwinkels
(Abb. 6)
Der Mikrofonwinkel kann eingestellt werden.
Einbau Deutsch Installation Français
Installation du microphone
Installez et orientez le microphone à un endroit
où il pourra bien capter la voix de la personne
qui commande le système par la voix.
ATTENTION
Une situation très dangereuse pourrait se présenter
si le fil du microphone devait s’enrouler autour de la
colonne de direction ou du levier de vitesses. Veillez à
cheminer le fil de manière qu’il ne fasse pas obstacle
à la conduite.
Installation du microphone sur
le pare-soleil
1. Fixez le microphone sur l’attache
fournie. (Fig. 1)
1 Microphone
2 Attache
2. Fixez l’attache du microphone sur le
pare-soleil. (Fig. 2)
Le pare-soleil étant relevé, fixez l’attache du
microphone. (Le taux de reconnaissance vocale
diminue quand le pare-soleil est abaissé.)
3
Attache de microphone
4 Serre-fils
Utilisez
des serre-fils vendus séparément pour
fixer le fil conducteur aux endroits nécessaires
dans le véhicule.
Installation du microphone sur
la colonne de direction
1. Fixez le microphone sur l’attache
fournie. (Fig. 3)
5 Microphone
6
Base du microphone
7 Attache
8
Cheminez le fil du microphone dans la rainure.
Le microphone peut être installé sans utiliser
l’attache du microphone. Dans ce cas, détachez
la base du microphone de l’attache. Pour
détacher la base du microphone de l’attache,
faites glisser la base du microphone.
2. Fixez l’attache du microphone sur la
colonne de direction. (Fig. 4) (Fig. 5)
9 Bande adhésive double face
a
Installez l’attache de microphone sur l’arrière de
la colonne de direction.
b Serre-fils
Utilisez
des serre-fils vendus séparément pour
fixer le fil conducteur aux endroits nécessaires
dans le véhicule.
Ajustement de l’angle du
microphone (Fig. 6)
L’angle du microphone peut être.
Installazione del microfono
Installare il microfono in una posizione e con
un orientamento che permettano una buona
captazione della voce della persona che controlla il
sistema di navigazione tramite la voce.
PRECAUZIONE
È estremamente pericoloso lasciare che il cavo del
microfono si impigli nella colonna dello sterzo o nella
leva del cambio. Assicurarsi di installare l’unità in
modo tale da non ostacolare la guida.
Quando si installa il microfono
sull’aletta parasole
1. Installare il microfono sul gancio
microfono. (Fig. 1)
1 Microfono
2
Gancio microfono
2. Installare il gancio microfono
sull’aletta parasole. (Fig. 2)
Installare il gancio microfono tenendo laletta parasole
alzata. (Abbassando l’aletta parasole si riduce il tasso di
riconoscimento dei comandi vocali.)
3
Gancio microfono
4
Morsetti
Usare dei morsetti (da reperire in commercio)
per fissare il cavo nei punti necessari all’interno
del veicolo.
Quando si installa il microfono
sulla colonna dello sterzo
1. Installare il microfono sul gancio
microfono. (Fig. 3)
5 Microfono
6
Base del microfono
7
Gancio microfono
8
Far passare il cavo del microfono nella
scanalatura.
Il microfono può essere installato anche
senza usare l’apposito gancio. In tal caso
occorre rimuovere la base da quest’ultimo
semplicemente facendola scorrere
2. Installare il gancio microfono sulla
colonna dello sterzo. (Fig. 4) (Fig. 5)
9 Nastro biadesivo
a
Installare il gancio microfono sul retro della
colonna dello sterzo.
b Morsetti
Usare
dei morsetti (da reperire in commercio)
per fissare il cavo nei punti necessari all’interno
del veicolo.
Regolazione dell’angolo del
microfono (Fig. 6)
L’angolo del microfono è regolabile.
Installazione Italiano
Bevestigen van de microfoon
Monteer de microfoon op een plaats en in de
richting waarin deze het stemgeluid van de
persoon die het systeem via spraak bedient
goed kan opvangen.
BELANGRIJK
Wanneer de microfoondraad zich rond de stuurkolom
of de versnellingspook wikkelt, ontstaat een bijzonder
gevaarlijke situatie. Let er bij het aanbrengen van de
microfoon op dat u op geen enkele wijze gehinderd
wordt bij de normale besturing van de auto.
Bevestigen van de microfoon op
de zonneklep
1. Monteer de microfoon in de
microfoonclip. (Afb. 1)
1 Microfoon
2 Microfoonclip
2. Monteer de microfoonclip op de
zonneklep. (Afb. 2)
Bevestig de microfoonclip op de omhooggeklapte
zonneklep. (Bij het omlaagklappen van de
zonneklep zal het stemherkenningsvermogen van
de microfoon afnemen.)
3 Microfoonclip
4 Klem
Klemmen
om de draad op de vereiste plaatsen
tegen het interieur van de auto te bevestigen.
Bevestigen van de microfoon op
de stuurkolom
1. Monteer de microfoon in de
microfoonclip. (Afb. 3)
5 Microfoon
6 Microfoonvoet
7 Microfoonclip
8
Laat de microfoondraad via de groef lopen.
De microfoon kan worden bevestigd zonder
gebruik te maken van de microfoonclip. Haal in
dit geval de voet van de microfoonclip. Schuif de
voet van de microfoonclip om deze los te maken.
2. Bevestig de microfoonclip op de
stuurkolom. (Afb. 4) (Afb. 5)
9 Dubbelzijdig plakband
a
Bevestig de microfoonclip op de bovenkant van
de stuurkolom.
b
Klem
Klemmen om de draad op de vereiste plaatsen
tegen het interieur van de auto te bevestigen.
Instellen van de hoek van de
microfoon (Afb. 6)
De hoek van de microfoon kan worden
ingesteld.
Installatie Nederlands
Установкамикрофона
Установите микрофон в позицию и
ориентируйте его так, чтобы он мог улавливать
голос человека, который оперирует системой.
ОСТОРОЖНО
Чрезвычайно опасно позволять проводам
микрофона обвиваться вокруг рулевой колонки
или рычага передач. Убедитесь, что установили
устройство таким образом, что оно не будет
затруднять движение.
Когдамикрофонустановлен
насолнцезащитномкозырьке
1. Установкамикрофонана
микрофонномзажиме.(Рис.1)
1 Микрофон
2 Микрофонный зажим
2. Установкамикрофонногозажимана
солнцезащитномкозырьке.(Рис.2)
Наверху солнцезащитного козырька
установите микрофонный зажим. (Опускание
солнцезащитного козырька уменьшает
степень распознавания голоса для
оперирующего голоса.)
3 Микрофонный зажим
4 Ск
обы
Используйте скобы для крепления проводов
внутри машины, где это необходимо.
Когдамикрофонустановлен
нарулевойколонке
1. Установкамикрофонана
микрофонномзажиме.(Рис.3)
5 Микрофон
6 Основ
ание микрофона
7 Микрофонный зажим
8 Поместит
е провод микрофона в канавку.
Микрофон может быть установлен без
использования микрофонного зажима. В этом
случае отсоедините основание микрофона от
микрофонного зажима. Чтобы отсоединить
основание микрофона от микрофонного
зажима, скользите основанием микрофона.
2. Установкамикрофонногозажимана
рулевойколонке.(Рис.4)(Рис.5)
9 Двусторонняя лента
a У
становите микрофонный зажим на задней
стороне рулевой колонки.
b Ск
оба
Используйте отдельно продаваемые скобы
для крепления проводов внутри автомобиля,
где это необходимо.
Регулировкаугланаклона
микрофона(Рис.6)
Угол микрофона может быть отрегулирован.
Установка Русский
Page 17 Page 18 Page 19 Page 20
Connecting the units English Connecting the units English
Note
When this unit is installed in a vehicle without ACC
(accessory) position on the ignition switch, red cable
must be wired to the terminal that can detect the
operation of the ignition key. Otherwise, battery drain
may result.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
ACC position
No ACC position
Use this unit in other than the following conditions
could result in fire or malfunction.
Vehicles with a 12-volt battery and negative
grounding.
Speakers with 50 W (output value) and 4 ohm to 8
ohm (impedance value).
To prevent short-circuit, overheating or malfunction,
be sure to follow the directions below.
Disconnect the negative terminal of the battery
before installation.
Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
Place all cables away from moving parts, such as
gear shift and seat rails.
Place all cables away from hot places, such as
near the heater outlet.
Do not pass the yellow cable through a hole into
the engine compartment to connect to a battery.
Cover any disconnected cable connectors with
insulating tape.
Do not shorten any cables.
Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
Use a fuse of the rating prescribed.
Never wire the speaker negative cable directly to
ground.
Never band together multiple speaker’s negative
cables.
Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
external power amp’s system remote control or the
vehicle’s auto-antenna relay control terminal (max.
300 mA, 12 V DC). If the vehicle is equipped with a
glass antenna, connect it to the antenna booster
power supply terminal.
Never connect blue/white cable to external power
amp’s power terminal. Also, never connect it to the
power terminal of the auto antenna. Otherwise,
battery drain or malfunction may result.
IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.
Black cable is ground. This cable and other product’s
ground cable (especially, high-current products such
as power amp) must be wired separately. Otherwise,
fire or malfunction may result if they are accidentally
detached.
Connection Diagram
1. USB cable
Connect to separately sold USB device.
2. Microphone input
3. AUX jack (3.5 ø)
Use a stereo mini plug cable to connect with
auxiliary device.
4. Wired remote input
Hard-wired remote control adaptor can be
connected (sold separately).
5. IP-BUS input (Blue)
6. Antenna jack
7. Rear output
8. Front output
9. Subwoofer output
10. This product
11. IP-BUS cable
12. Multi-CD player (sold separately)
13. Note
Depending on the kind of vehicle, the function
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
14. Connect leads of the same color to
each other.
15. Cap (1*)
Do not remove cap if this terminal is not in use.
16. Fuse (10 A)
17. Yellow (3*)
Back-up (or accessory)
18. Yellow (2*)
Connect to the constant 12 V supply terminal.
19. Fuse resister
20. Red (5*)
Accessory (or back-up)
21. Red (4*)
Connect to terminal controlled by ignition
switch (12 V DC).
22. Black (chassis ground)
Connect to a clean, paint-free metal location.
23. ISO connector
Note
In some vehicles, the ISO connector may
be divided into two. In this case, be sure to
connect to both connectors.
24. Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
25.
Blue/white (7*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
26. Blue/white (6*)
The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6*
and 7* when Pin 5 is an antenna control type.
In another type of vehicle, never connect 6*
and 7*.
27. Speaker leads
White: Front left +
White/black: Front left *
Gray: Front right +
Gray/black: Front right *
Green: Rear left + or subwoofer +
Green/black: Rear left * or subwoofer *
Violet: Rear right + or subwoofer +
Violet/black: Rear right * or subwoofer *
28. To rear output
29. To front output
30. To subwoofer output
31. Connect with RCA cables (sold separately)
32. Power amp (sold separately)
33. System remote control
34. Left
35. Right
36.Subwoofer
37. Front speaker
38. Rear speaker
39. Perform these connections when using the
optional amplifier.
40. Notes
Change the initial setting of this unit (refer
to the operation manual). The subwoofer
output of this unit is monaural.
When using a subwoofer of 70 W (2 ), be
sure to connect with Violet and Violet/black
leads of this unit. Do not connect anything
with Green and Green/black leads.
41. Microphone
1.5 m
9. Subwoofer output
15 cm
10. This product
20 cm
6. Antenna jack
8. Front output
7. Rear output
5. IP-BUS input (Blue)
4. Wired remote input
Hard-wired remote control
adaptor can be connected
(sold separately).
11. IP-BUS cable
39. Perform these connections when
using the optional amplifier.
1*
3* 2*
4*5*
13. Note
Depending on the kind of vehicle,
the function of 3* and 5* may be
different. In this case, be sure to
connect 2* to 5* and 4* to 3*.
14. Connect leads of the
same color to each other.
15. Cap (1*)
Do not remove cap
if this terminal is
not in use.
17. Yellow (3*)
Back-up (or
accessory)
20. Red (5*)
Accessory
(or back-up)
18. Yellow (2*)
Connect to the constant
12 V supply terminal.
21. Red (4*)
Connect to terminal controlled by
ignition switch (12 V DC).
23. ISO connector
Note
In some vehicles, the ISO connector
may be divided into two. In this case,
be sure to connect to both connectors.
27. Speaker leads
White: Front left
White/black: Front left
Gray: Front right
Gray/black: Front right
Green: Rear left or subwoofer
Green/black: Rear left or subwoofer
Violet: Rear right or subwoofer
Violet/black: Rear right or subwoofer
24. Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
25. Blue/white (7*)
Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).
22. Black (chassis ground)
Connect to a clean, paint-free metal location.
The pin position of the ISO connector will
differ depends on the type of vehicle.
Connect 6* and 7* when Pin 5 is an
antenna control type. In another type of
vehicle, never connect 6* and 7*.
26. Blue/white (6*)
12.Multi-CD player
(sold separately)
40. Notes
Change the initial setting of this unit (refer to the
operation manual). The subwoofer output of this unit is
monaural.
When using a subwoofer of 70 W (2 ), be sure to
connect with Violet and Violet/black leads of this unit.
Do not connect anything with Green and Green/black
leads.
31. To subwoofer output
29. To front output
28. To rear output
32. Power amp
(sold separately)
35. Right34. Left
32. Power amp
(sold separately)
32. Power amp
(sold separately)
31. Connect with RCA cables
(sold separately)
33. System remote control
37. Front speaker 37. Front speaker
38. Rear speaker 38. Rear speaker
36. Subwoofer
36. Subwoofer
16. Fuse (10 A)
19. Fuse resister
2. Microphone input
1. USB cable
Connect to sparately
sold USB device.
3. AUX jack (3.5 φ)
Use a stereo mini plug cable
to connect with auxiliary
device.
41. Microphone
4 m
Page 21 Page 22 Page 23 Page 24
Conexión de las unidades
Español
Conexión de las unidades
Español
Anschließen der Geräte
Deutsch
Anschließen der Geräte
Deutsch
Nota
Cuando se instale esta unidad en un vehículo sin
la posición ACC (accesorio) en el interruptor de
encendido, se debe conectar el cable rojo al terminal
que puede detectar la operación de la llave de
encendido.
De
lo contrario, la batería puede descargarse.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
Posición ACC
Sin posición ACC
El uso de esta unidad en condiciones diferentes
de las siguientes podría causar un fuego o fallo de
funcionamiento.
Vehículos con una batería de 12 voltios y puesta a
tierra negativa.
Altavoz con 50 W (valor de salida) y de 4 a 8
ohmios (valor de impedancia).
Para prevenir cortocircuitos, sobrecalentamiento
o fallo de funcionamiento, asegúrese de seguir las
instrucciones a continuación.
Desenchufe el terminal negativo de la batería
antes de la instalación.
Fije el cableado con abrazaderas de cable o
con cinta adhesiva. Para proteger el cableado,
envuélvalo con cinta adhesiva donde el cableado
se apoya sobre piezas metálicas.
Posicione todos los cables alejados de las piezas
móviles, como el cambio de marchas y rieles de
los asientos.
Posicione todos los cables alejados de lugares
calientes como cerca de la salida del calentador.
No pase el cable amarillo a través de un agujero
en el compartimiento del motor para conectar la
batería.
Cubra cualquier conector de cable desconectado
con cinta de aislamiento.
No acorte ningún cable.
No corte nunca el aislamiento del cable de
alimentación de esta unidad para compartir
la energía con otro equipo. La capacidad de
corriente del cable es limitada.
Utilice un fusible con la capacidad especificada.
No conecte nunca el cable negativo de altavoz
directamente a la puesta a tierra.
No junte nunca múltiples cables negativos de
altavoz.
La señal de control se emite a través del cable azul/
blanco cuando se enciende esta unidad. Conéctelo
a un terminal de control de sistema de amplificador
de potencia externo o al terminal de control de relé
de antena automática del vehículo (máx. 300 mA, 12
V CC). Si el vehículo está equipado con una antena
de vidrio, conéctelo al terminal de suministro de
potencia de refuerzo de la antena.
No conecte nunca el cable azul/blanco al terminal de
alimentación de un amplificador de potencia externo.
Igualmente, no conéctelo nunca al terminal de
alimentación de la antena automática.
De lo contrario, puede ocurrir la descarga de la
batería o un fallo de funcionamiento.
Los conectores IP-BUS están codificados en colores.
Asegúrese de conectar los conectores del mismo
color.
El cable negro es para la puesta a tierra. Se debe
conectar este cable y el cable de puesta a tierra
de otro producto (especialmente de productos de
alta corriente como un amplificador de potencia)
separadamente. De lo contrario, puede ocurrir un
fuego o fallo de funcionamiento si los cables se
sueltan accidentalmente.
Diagrama de conexión
1. Cable USB
Conecte al dispositivo USB vendido
separamente.
2. Entrada de micrófono
3. Jack AUX (3.5 ø)
Utilice un cable con clavija mini estéreo con el
equipo auxiliar.
4. Entrada remota cableada
Se puede conectar el adaptador de control
remoto cableado (vendido separadamente).
5. Entrada IP-BUS (Azul)
6. Toma de antena
7. Salida trasera
8. Salida delantera
9. Salida de altavoz de subgraves
10. Este producto
11. Cable IP-BUS
12. Reproductor de Multi-CD (vendido
separadamente)
13. Nota
Dependiendo del tipo de vehículo, la función
de 3* y 5* puede ser diferente. En este caso,
asegúrese de conectar 2* a 5* y 4* a 3*.
14. Conecte los hilos del mismo color a cada otro.
15. Tapa (1*)
No quite la tapa cuando no se utiliza este
terminal.
16. Fusible (10 A)
17. Amarillo (3*)
Reserva (o accesorio)
18. Amarillo (2*)
Conecte el terminal de suministro de 12 V
constante.
19. Resistencia de fusible
20. Rojo (5*)
Accesorio (o reserva)
21. Rojo (4*)
Conecte al terminal controlado por del
interruptor de encendido (12 V CC).
22. Negro (masa de la carrocería)
Conecte a un punto de metal limpio, libre de
pintura.
23. Conector ISO
Nota
En algunos vehículos, puede que el conector
ISO esté dividido en dos. En este caso,
asegúrese de conectar a ambos conectores.
24. Azul/blanco
Conecte al terminal de control de sistema del
amplificador de potencia (máx. 300 mA 12 V
CC).
25. Azul/blanco (7*)
Conecte al terminal de control de relé de
antena automática (máx. 300 mA 12 V CC).
26. Azul/blanco (6*)
La posición de los contactos del conector ISO
difiere dependiendo del tipo del vehículo.
Conecte 6* y 7* cuando el contacto 5 es del
tipo de control de antena. En otros tipos de
vehículo, no conecte nunca 6* y 7*.
27. Hilos de altavoz
Blanco: Izquierda delantera +
Blanco/negro: Izquierda delantera *
Gris: Derecha delantera +
Gris/negro: Derecha delantera *
Verde: Izquierda trasera +
o altavoz de subgraves +
Verde/negro: Izquierda trasera *
o altavoz de subgraves *
Violeta: Derecha trasera +
o altavoz de subgraves +
Violeta/negro: Derecha trasera *
o altavoz de subgraves *
28. A la salida trasera
29. A la salida delantera
30. A la salida del altavoz de subgraves
31. Conecte los cables RCA (vendidos
separadamente)
32. Amplificador de potencia (vendido
separadamente)
33. Control remoto de sistema
34. Izquierda
35. Derecha
36. Altavoz de subgraves
37. Altavoz delantero
38. Altavoz trasero
39. Realice estas conexiones cuando utilice el
amplificador opcional.
40. Notas
Cambie el ajuste inicial de esta unidad
(refiérase al manual de operación). La salida
de altavoz de subgraves de esta unidad es
monofónica.
Cuando utilice un altavoz de subgraves de
70 W (2 ), asegúrese de conectarlo con
los hilos Violeta y Violeta/negro de esta
unidad. No conecte nada con los hilos Verde
y Verde/negro.
41. Micrófono
Hinweise
Wenn dieses Gerät in einem Auto eingebaut wird,
as auf dem Zündschalter keine ACC (Zubehör)-
Position hat, sollte die rote Leitung des Geräts an eine
Klemme angeschlossen werden, die die Position des
Zündschalters erfassen kann.
Anderenfalls
kann die Autobatterie entleert
werden.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
ACC-Position
Keine A
CC-Position
Wenn das Gerät nicht unter den folgenden
Bedingungen eingebaut wird, kann ein Brand oder
eine Funktionsstörung auftreten.
Fahrzeuge mit einer 12-Volt-Batterie und negativer
Erdung.
Lautsprecher mit 50 W (Ausgangsleistung) und 4
bis 8 Ohm (Impedanz).
Um Kurzschlüsse, eine Überhitzung oder
Funktionsstörung zu verhindern, befolgen Sie bitte die
folgenden Hinweise:
Trennen Sie die negative Klemme der Batterie vor
dem Einbau ab.
Sichern Sie die Leitungen mit Kabelklemmen oder
Klebeband. Zum Schutz der Leitungen sollten
sie an Stellen, wo sie Metallteile berühren, mit
Klebeband umwickelt werden.
Verlegen Sie alle Leitungen so, dass keine
beweglichen Teile, wie die Gangschaltung und die
Sitzschienen, berühren.
Verlegen Sie alle Kabel so, dass sie von heißen
Stellen, wie etwa der Heizungsauslassöffnung
entfernt sind.
Führen Sie die gelbe Leitung zum Anschluss
an die Batterie nicht durch ein Loch in den
Motorraum ein.
Umwickeln Sie abgetrennte Leitungen mit
Isolierband.
Verkürzen Sie keine Kabel.
Führen Sie niemals anderen Geräten
Strom zu, indem Sie die Isolierung der
Stromversorgungsleitung dieses Geräts
durchschneiden
und davon Strom abzapfen. Die
Strombelastbarkeit der Leitung ist begrenzt.
Verwenden Sie eine Sicherung mit dem
vorgeschriebenen Nennwert.
Schließen Sie das negative Lautsprecherkabel nie
direkt an die Erdung an.
Bündeln Sie nie die negativen Kabeln mehrerer
Lautsprecher.
Das Steuersignal wird über das blaue/weiße Kabel
ausgegeben, wenn dieses Geräts eingeschaltet wird.
Schließen Sie es an eine System-Fernbedienung
eines externen Leistungsverstärkers oder an die
Autoantennenrelais-Steuerungsklemme des
Fahrzeugs an (max. 300 mA, 12 V Gleichspannung).
Wenn das Fahrzeug mit einer Fensterantenne
ausgestattet ist, schließen Sie es an die
Antennenverstärker-Stromversorgungsklemme an.
Schließen Sie das blaue/weiße Kabel nie an die
Leistungsklemme des Verstärkers an. Außerdem darf
das blaue/weiße Kabel nicht an die Leistungsklemme
der Auto-Antenne angeschlossen werden. Ein solcher
Anschluss könnte zu einer Belastung der Batterie
führen und Funktionsstörungen verursachen.
Die IP-BUS-Leitungen sind farbcodiert. Achten Sie
immer darauf, Leitungen derselben Farbe miteinander
zu verbinden.
Das schwarze Kabel ist das Erdungskabel. Dieses
Kabel ist getrennt von der Erde von Hochstrom-
Geräten, wie z. B. Leistungsverstärkern, zu erden.
Anderenfalls besteht die Gefahr einer Beschädigung
der Geräte oder eines Brandes, falls die Erdungsstelle
versehentlich abgetrennt wird.
Anschlussdiagramm
1. USB-Kabel
Für den Anschluss an das separat erhältliche
USB-Gerät.
2. Mikrofoneingang
3. AUX-Buchse (3.5 ø)
Zur Verbindung mit Zusatzausrüstung
verwenden Sie ein Stereo-Ministeckerkabel.
4. Buchse für die verdrahtete Fernbedienung
Hier kann ein Drahtfernbedienungsadapter
(getrennt erhältlich) angeschlossen werden.
5. IP-BUS-Eingang (Blau)
6. Antennebuchse
7. Ausgang für hintere Zusatzlautsprecher
8. Ausgang für vorderen Zusatzlautsprecher
9. Subwoofer-Ausgang
10. Dieses Produkt
11. IP-BUS-Kabel
12. Multi-CD-Player (getrennt erhältlich)
13. Hinweis:
Je nach Art des Fahrzeugs besitzen 3* und 5*
u. U. unterschiedliche Funktionen. Verbinden
Sie in einem solchen Fall 2* mit 5* und 4* mit
3*.
14. Verbinden Sie Leitungen derselben Farbe
miteinander.
15. Kappe (1*)
Wenn dieser Steckverbinder nicht verwendet
wird, lassen Sie die Kappe aufgesetzt.
16. Sicherung (10 A)
17. Gelb (3*)
Reserve (oder Zubehör)
18. Gelb (2*)
An eine Stromversorgung anschließen, die
immer Gleichstrom von 12 V führt.
19. Sicherungswiderstand
20. Rot (5*)
Zubehör (oder Reserve)
21. Rot (4*)
An eine Stromversorgung anschließen, (12 V
Gleichspannung), die mit dem Zündschloss ein-/
ausgeschaltet wird.
22. Schwarz (Erdung)
An ein sauberes Metallteil anschließen, das von
Farbe frei ist.
23. ISO-Anschluss
Hinweis:
Bei einigen Fahrzeugen kann der ISO-
Steckverbinder in zwei Hälften geteilt sein. In
diesem Fall ist der Anschluss unbedingt an
beiden Steckverbindern vorzunehmen.
24. Blau/weiß
An den Systemsteuerungs-Anschluss des
Leistungsverstärkers (max. 300 mA, 12 V
Gleichspannung) anschließen.
25.
Blau/weiß (7*)
An die die Autoantennenrelais-Steuerungsklemme
anschließen (max. 300 mA, 12 V Gleichspannung).
26. Blau/weiß (6*)
Die Pin-Position des ISO-Anschlusses
hängt vom Fahrzeugtyp ab. 6* und 7*
anschließen, wenn es sich bei Pin 5 um einen
Antennensteuerungstyp handelt. Bei einem
anderen Fahrzeugtyp 6* und 7* niemals
anschließen.
27. Lautsprecherzuleitungen
Weiß: Vorne links +
Weiß/Schwarz: Vorne links *
Grau: Vorne rechts +
Grau/Schwarz: Vorne rechts *
Grün: Hinten links + oder Subwoofer +
Grün/Schwarz: Hinten links * oder Subwoofer *
Violett: Hinten rechts + oder Subwoofer +
Violett/Schwarz: Hinten rechts * oder Subwoofer *
28. Zum hinteren Ausgang
29. Zum vorderen Ausgang
30.Zum Subwoofer-Ausgang
31. Mit RCA-Kabeln verbinden (getrennt erhältlich)
32. Leistungsverstärker (getrennt erhältlich)
33. System-Fernbedienung
34. Links
35. Recht
36. Subwoofer
37. Vorderer Lautsprecher
38. Hinterer Lautsprecher
39. Bei Gebrauch des optionalen Verstärkers diese
Anschlüsse vornehmen.
40. Hinweise
Ändern Sie die Grundeinstellung dieses
Geräts (siehe Bedienungsanleitung). Der
Subwoofer-Ausgang dieses Geräts ist Mono.
Bei Verwendung eines Subwoofers von 70 W
(2 ) achten Sie darauf, den Anschluss an die
violetten und violetten/schwarzen Leitungen
dieses Geräts herzustellen. Stellen Sie keinen
Anschluss mit den grünen und grünen/
schwarzen Leitungen her.
41. Mikrofon
Page 25 Page 26 Page 27 Page 28
Connexions des appareils
Français
Connexions des appareils
Français
Collegamento delle unità
Italiano
Collegamento delle unità
Italiano
Remarque
Si cet appareil est installé dans un véhicule sans
position ACC (accessoire) sur le commutateur
d’allumage, le câble rouge doit être connecté à une
borne qui peut détecter la position du commutateur
d’allumage. Sinon, la batterie risque de se décharger.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
Position ACC
Pas de p
osition ACC
Utiliser cet appareil dans d’autres conditions que les
conditions suivantes peut entraîner un incendie ou
un mauvais fonctionnement.
Véhicule avec une batterie de 12 volts et une mise
à la masse négative.
Enceintes de 50 W (valeur de sortie) et de 4 ohms
à 8 ohms (valeur d’impédance).
Pour éviter tout court-circuit, surchauffe ou
mauvais fonctionnement, assurez-vous de suivre les
instructions ci-dessous.
Déconnectez la borne négative de la batterie
avant l’installation.
Fixez solidement les câbles avec des serre-câbles
ou du ruban adhésif. Pour protéger le câblage,
entourez-le de ruban adhésif à l’endroit où il est
en contact avec des pièces métalliques.
Tenez tous les câbles à l’écart des parties mobiles,
telles que le levier de vitesse et les rails des
sièges.
Tenez tous les câbles à l’écart des endroits
chauds, tels que les sorties du chauffage.
Ne faites pas passer le câble jaune par un
trou dans le compartiment du moteur pour le
connecter à la batterie.
Recouvrez tous les câbles non connectés avec du
ruban isolant.
Ne raccourcissez aucun câble.
Ne coupez jamais l’isolant du câble
d’alimentation de cet appareil afin partager
l’alimentation avec un autre appareil. La capacité
électrique du câble est limitée.
Utilisez un fusible de la valeur donnée.
Ne connectez jamais le câble négatif des
enceintes directement à la masse.
N’attachez jamais ensemble plusieurs câbles
négatifs de plusieurs enceintes.
Le signal de commande est sorti par le câble bleu/
blanc quand cet appareil est sous tension. Connectez-
le à la télécommande d’un système d’amplification
extérieur ou à la prise de commande du contrôle
de relais de l’antenne automatique (max. 300 mA,
12 V CC). Si le véhicule est équipée d’une antenne
de vitre, connectez-la à la prise d’alimentation de
l’amplificateur d’antenne.
Ne connectez jamais le câble bleu/blanc à la prise
d’alimentation d’un amplificateur extérieur. Et
ne le connectez pas à la prise d’alimentation de
l’antenne automatique. Sinon, la batterie risque de
se décharger ou un mauvais fonctionnement peut se
produire.
Les connecteurs IP-BUS sont codés par couleur.
Assurez-vous de connecter les connecteurs de même
couleur.
Le câble noir est pour la masse. Ce câble et les câbles
de masse des autres produits (en particulier les
appareils à haute intensité tels que les amplificateurs)
doivent être câblés séparément. Sinon, ils peuvent
entraîner un incendie ou un mauvais fonctionnement
s’ils se détachent.
Diagramme de connexion
1. Câble USB
Connectez-le à un périphérique USB vendu
séparément.
2. Entrée microphone
3. Prise AUX (3.5 ø)
Utilisez un câble à fiches stéréo mini pour
raccorder un appareil auxiliaire.
4. Entrée de télécommande câblée
Un adaptateur de télécommande câblée peut
être connecté (vendu séparément).
5. Entrée IP-BUS (Bleu)
6. Prise d’antenne
7. Sortie arrière
8. Sortie avant
9. Sortie du caisson de grave
10. Cet appareil
11. Câble IP-BUS
12. Lecteur de CD à chargeur (vendu séparément)
13. Remarque
En fonction du type de véhicule, la fonction de
3* et de 5* peut différer. Sans ce cas, assurez-
vous de connecter 2* à 5* et 4* à 3*.
14. Connectez les câbles de la même couleur les
uns aux autres.
15. Capuchon (1*)
Ne retirez pas le capuchon si cette prise n’est
pas utilisée.
16. Fusible (10 A)
17. Jaune (3*)
Secours (ou accessoire)
18. Jaune (2*)
Connectez à une prise d’alimentation
constante 12 V.
19. Résistance fusible
20. Rouge (5*)
Accessoire (ou secours)
21. Rouge (4*)
Connectez à une prise commandée par le
commutateur d’allumage (12 V CC).
22. Noire (masse au châssis)
Connectez à une section métallique propre et
sans peinture.
23. Connecteur ISO
Remarque
Dans certains véhicule, le connecteur ISO peut
être divisé en deux. Dans ce cas, assurez-vous
de faire la connexion aux deux connecteurs.
24. Bleu/blanc
Connectez à la prise de commande du système
de l’amplificateur de puissance (max. 300 mA
12 V CC).
25. Bleu/blanc (7*)
Connectez à la prise du contrôle de relais de
l’antenne automatique (max. 300 mA, 12 V CC).
26. Bleu/blanc (6*)
La position des broches du connecteur ISO
diffère en fonction du type de véhicule.
Connectez 6* et 7* quand la broche 5
correspond à la commande de l’antenne. Dans
les autres cas, ne connectez jamais 6* et 7*.
27. Câbles d’enceinte
Blanc: Avant gauche +
Blanc/noir: Avant gauche *
Gris: Avant droit +
Gris/noir: Avant droit *
Vert: Arrière gauche + ou caisson de grave +
Vert/noir: Arrière gauche *
ou caisson de grave *
Violet: Arrière droit + ou caisson de grave +
Violet/noir: Arrière droit *
ou caisson de grave *
28. À la sortie arrière
29. À la sortie avant
30. À la sortie du caisson de grave
31. Connectez aux câbles cinch (RCA) (vendus
séparément)
32. Amplificateur de puissance (vendu séparément)
33. Télécommande du système
34. Gauche
35. Droit
36. Caisson de grave
37. Enceinte avant
38. Enceinte arrière
39. Réalisez ces connexions lors de l’utilisation de
l’amplificateur en option.
40. Remarques
Change le réglage initial de cet appareil
(reportez-vous aux mode d’emploi). La
sortie de caisson de grave de cet appareil est
monophonique.
Lors de l’utilisation d’un caisson de grave de
70 W (2 ), assurez-vous de le raccorder aux
câbles Violet et Violet/noir de cet appareil. Ne
connectez rien aux câbles Vert et Vert/noir.
41. Microphone
Nota
Qualora l’unità venga installata in un veicolo la cui
chiavetta di accensione è sprovvista della posizione
ACC (accessori), il cavo rosso deve essere collegato
al terminale in grado di rilevare il funzionamento della
chiavetta stessa.
In
caso contrario la batteria si scaricherebbe.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
Posizione ACC
Assenza di posizione ACC
L’impiego dell’unità in condizioni diverse
dalle seguenti potrebbe dar luogo a incendi o
malfunzionamenti:
Veicoli provvisti di batteria da 12 V con messa a
terra sul negativo.
Altoparlanti da 50 W (uscita) e da 4 ohm a
8
ohm (impedenza).
Per impedire il verificarsi di cortocircuiti, di
surriscaldamento o di malfunzionamenti
raccomandiamo di osservare le seguenti istruzioni.
Prima di procedere con l’installazione scollegate il
terminale negativo della batteria.
Bloccate i cavi con apposite fascette o con del
nastro adesivo. Per proteggere i cavi che scorrono
contro le parti metalliche del veicolo avvolgeteli
inoltre con del nastro adesivo.
Allontanate tutti i cavi da qualsiasi parte in
movimento quali, ad esempio, la leva del cambio
e le guide dei sedili.
Allontanate tutti i cavi da punti ad elevata
temperatura quali, ad esempio, gli effusori del
sistema di riscaldamento del veicolo.
Per collegare il cavo giallo alla batteria non fatelo
passare per un foro ricavato nella struttura di
separazione dal vano del motore.
Proteggete con del nastro adesivo tutti i
connettori non usati.
Non accorciate alcun cavo di collegamento.
Non tagliate la guaina d’isolamento del cavo
di alimentazione di questa unità in modo da
prelevare corrente per alimentare altri apparecchi.
La capacità di corrente di questo cavo è infatti
limitata.
Usate solo un fusibile della capacità prescritta.
Non collegate mai direttamente a terra il cavo
negativo degli altoparlanti.
Non raggruppate fra loro il cavo negativo di più
altoparlanti.
Quando l’unità è accesa il segnale di controllo
è posto in uscita attraverso il cavo blu/bianco.
Collegatelo al telecomando di un amplificatore di
potenza esterno o al terminale di controllo del relé
dell’antenna automatica del veicolo (massimo 300
mA e 12 V CC). Se il veicolo è provvisto di un’antenna
a vetro collegatela al terminale di alimentazione del
relativo booster.
Non collegate il cavo blu/bianco al terminale di
alimentazione dell’amplificatore di potenza esterno.
Non collegatelo inoltre al terminale di alimentazione
dell’antenna.
In caso contrario la batteria si scaricherebbe oppure
si potrebbero verificare dei malfunzionamenti.
I connettori IP-BUS sono codificati a colore. È
pertanto necessario collegarli a connettori dello
stesso colore.
Il cavo nero va usato solo per la messa a terra. Questo
cavo e il cavo di messa a terra di altri apparecchi
(in particolare quelli ad alta corrente quali gli
amplificatori di potenza) devono essere collegati
separatamente.
In caso contrario, qualora si scolleghino
accidentalmente, si potrebbero verificare incendi o
malfunzionamenti.
Schema di collegamento
1. Cavo USB
Da collegare a una periferica USB acquistata a
parte.
2. Ingresso microfono
3. Presa AUX (3.5 ø)
Per il collegamento all’apparecchio ausiliario
utilizzate un cavo con spina stereo mini.
4. Ingresso del telecomando a filo
Qui si collega l’adattatore del telecomando a
filo (venduto a parte).
5. Ingresso IP-BUS (Blu)
6. Presa d’antenna
7. Uscita posteriore
8. Uscita anteriore
9. Uscita del subwoofer
10. Questo apparecchio
11. Cavo IP-BUS
12. Multilettore CD (venduto separatamente)
13. Nota
In funzione del tipo di veicolo le funzione di 3*
e di 5* potrebbe differire. In tal caso collegare
2* a 5* e 4* a 3*.
14. Collegare fra loro i cavi di uguale colore.
15. Capocorda (1*)
Non deve essere rimosso quando non si
impiega questo connettore.
16. Fusibile (10 A)
17. Giallo (3*)
Retromarcia (o accessorio)
18. Giallo (2*)
Da collegare al terminale costantemente
alimentato a 12 V.
19. Resistenza fusibile
20. Rosso (5*)
Accessorio (o retromarcia)
21. Rosso (4*)
Da collegare al terminale controllato dalla
chiavetta di accensione (12 V CC).
22. Nero (messa a terra sulla carrozzeria)
Da collegare in un punto metallico pulito e non
verniciato.
23. Connettore ISO
Nota
In alcuni veicoli il connettore ISO potrebbe
essere separato in due. In tal caso è necessario
collegare entrambi.
24. Blu/bianco
Da collegare al terminale di controllo di sistema
dell’amplificatore di potenza (massimo 300 mA
12 V CC).
25. Blu/bianco (7*)
Da collegare al terminale di controllo del relé
dell’antenna automatica (massimo 300 mA
12 V CC).
26. Blu/bianco (6*)
La posizione dei contatti del connettore ISO
può differire in funzione del tipo di veicolo.
Collegare 6* e 7* qualora il contatto 5 sia del
tipo per controllo dell’antenna. In altri tipi di
veicolo 6* e 7* non devo mai essere collegati.
27. Cavi altoparlanti
Bianco: Anteriore sinistro +
Bianco/nero: Anteriore sinistro *
Grigio: Anteriore destro +
Grigio/nero: Anteriore destro *
Verde: Posteriore sinistro + o subwoofer +
Verde/nero: Posteriore sinistro *
o subwoofer *
Viola: Posteriore destro + o subwoofer +
Viola/nero: Posteriore destro * o subwoofer *
28. All’uscita posteriore
29. All’uscita anteriore
30. All’uscita subwoofer
31. Da collegare ai cavi RCA (venduti a parte)
32. Amplificatore di potenza (venduto a parte)
33. Telecomando del sistema
34. Sinistra
35. Destra
36. Subwoofer
37. Diffusore anteriore
38. Diffusore posteriore
39. Questi collegamenti devono essere eseguiti
quando s’impiega l’amplificatore opzionale.
40. Note
Cambiare l’impostazione iniziale di questa
unità (far riferimento al manuale d’istruzioni
per l’uso). L’uscita subwoofer di questa unità
è di tipo mono.
Se s’impiega un subwoofer da 70 W (2 ) è
necessario collegarlo con i cavi viola e viola/
nero di questa unità. Nulla deve invece essere
collegato con i cavi verde e verde/nero.
41. Microfono
Page 29 Page 30 Page 31 Page 32
Подключениеустройств
Pyccкий
Подключениеустройств
Pyccкий
Aansluiten van de toestellen
Nederlands
Aansluiten van de toestellen
Nederlands
Opmerking
Wanneer dit toestel geïnstalleerd is in een voertuig
zonder ACC (accessoire) stand op het contactslot,
moet de rode draad worden verbonden met een
aansluiting die de stand van de contactsleutel kan
herkennen. Anders kan de accu leeglopen.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
ACC stand
Geen ACC stand
Gebruik van dit toestel onder andere dan de
volgende omstandigheden kan leiden tot brand of
storingen.
Voertuigen met een negatief geaarde 12 V accu.
Luidsprekers van 50 W (uitgangsvermogen) en 4
Ohm tot 8 Ohm (impedantie).
Om kortsluiting, oververhitting of andere
storingen
te voorkomen moet u de onderstaande
instructies opvolgen.
Koppel de negatieve pool van de accu los voor u
begint met de installatie.
Zet alle bedrading vast met kabelklemmen of
isolatieband. Ter bescherming van de
bedrading
dient u deze te omwikkelen met
isolatieband waar de bedrading met metalen
onderdelen in aanraking komt.
Houd alle bedrading uit de buurt van
bewegende
onderdelen, zoals de
versnellingspook
en de stoelenrails.
Houd de bedrading uit de buurt van zeer warme
plekken, zoals bij een
verwarmingsrooster.
Leid de gele draad niet door een gat naar het
motorcompartiment om aan te sluiten op de accu.
Plak eventuele losse aansluitingen,
draadeinden
of stekkers netjes af met
isolatieband.
Maak de kabels niet korter.
Tap in geen geval de stroomkabel voor dit toestel
af om andere apparatuur van stroom te voorzien.
Het vermogen van de draad is beperkt.
Gebruik een zekering met het voorgeschreven
vermogen.
Sluit de negatieve luidsprekerdraden in geen
geval direct op aarde aan.
Bundel de negatieve luidsprekerdraden in geen
geval samen.
Via de blauw/witte draad wordt een stuursignaal
geproduceerd wanneer dit toestel is ingeschakeld.
Verbind deze met de systeemafstandsbediening van
een externe eindversterker, of met de
stuuraansluiting
voor het relais van de antenne van
het voertuig (max. 300 mA, 12 V
gelijkstroom).
Als het voertuig een ruitantenne
heeft, dient u deze draad te verbinden met de
stroomaansluiting van de
antennesignaalversterker
(booster).
Verbind de blauw/witte draad in geen geval met de
stroomaansluiting van een externe
eindversterker
. Verbind deze draad ook in geen geval
met de stroomaansluiting zelf van de antenne van de
auto. Doet u dit toch, dan kan de accu leeglopen of
kunnen zich andere storingen voordoen.
IP-BUS stekkers zijn kleurgecodeerd. Let erop dat u
alleen stekkers van dezelfde kleur op elkaar aansluit.
De zwarte draad is de aarding. Deze draad en de
aardingen van andere apparatuur (in het bijzonder
producten met een hoog vermogen, zoals een
eindversterker), moeten onafhankelijk van elkaar
worden aangesloten. Doet u dit niet, dan kan er brand
ontstaan of kunnen zich storingen
voordoen
wanneer de bedrading onbedoeld los raakt.
Aansluitingsschema
1. USB kabel
Sluit deze aan op een los verkrijgbaar USB
apparaat.
2. Microfoon ingangsaansluiting
3. AUX aansluiting (3.5 ø)
Gebruik een kabel met een stereo ministekker
voor het aansluiten van externe apparatuur.
4. Afstandsbediening met draad
Er kan een adapter voor een afstandsbediening
met draad worden aangesloten (los
verkrijgbaar).
5. IP-BUS ingangsaansluiting (Blauw)
6. Antenne-aansluiting
7. Achter-uitgang
8. Voor-uitgang
9. Subwoofer uitgang
10. Dit product
11. IP-BUS-kabel
12. Multi CD-wisselaar (los verkrijgbaar)
13. Opmerking
Afhankelijk van het soort voertuig is het
mogelijk dat de functies van 3* en 5*
verschillen. Let er in een dergelijk geval op dat
u 2* op 5* en 4* op 3* aansluit.
14. Sluit in het algemeen draden van dezelfde
kleur op elkaar aan.
15. Dop (1*)
Laat het dopje zitten wanneer de aansluiting
niet wordt gebruikt.
16. Zekering (10 A)
17. Geel (3*)
Back-up (of accessoire)
18. Geel (2*)
Verbinden met de continue 12 V
stroomaansluiting.
19. Zekering
20. Rood (5*)
Accessoire (of back-up)
21. Rood (4*)
Verbinden met een elektrische aansluiting die
aangestuurd wordt via het contactslot
(12 V gelijkstroom).
22. Zwart (chassis aarde)
Aansluiten op een schone, blank metalen plek.
23. ISO stekker
Opmerking
In sommige voertuigen kan de ISO stekker
in twee stukken gedeeld zijn. Sluit in een
dergelijk geval beide stekkers aan.
24. Blauw/wit
Verbinden met de
systeembedieningsaansluiting van de
eindversterker (max. 300 mA 12 V
gelijkstroom).
25.
Blauw/wit (7*)
Verbinden met de stuuraansluiting van het
relais van de antenne van het voertuig (max.
300 mA 12 V gelijkstroom).
26. Blauw/wit (6*)
De penposities van de ISO stekker hangen
mede af van het type voertuig. Sluit 6* en 7*
aan wanneer pen 5 de antenne aanstuurt.
In andere typen voertuigen hoeft u 6* en 7*
helemaal niet aan te sluiten.
27. Luidsprekerdraden
Wit: Links voor +
Wit/zwart: Links voor *
Grijs: Rechts voor +
Grijs/zwart: Rechts voor *
Groen: Links achter + of subwoofer +
Groen/zwarte: Links achter * of subwoofer *
Paars: Rechts achter + of subwoofer +
Paars/zwarte: Rechts achter * of subwoofer *
28. Naar de achter-uitgang
29. Naar de voor-uitgang
30. Naar de subwoofer uitgang
31. Aansluiten met RCA (tulpstekker) kabels (los
verkrijgbaar)
32. Eindversterker (los verkrijgbaar)
33. Systeemafstandsbediening
34. Links
35. Rechts
36. Subwoofer
37. Voor-luidspreker
38. Achter-luidspreker
39. Voer deze verbindingen uit wanneer u de los
verkrijgbare versterker gebruikt.
40. Opmerkingen
Verander de basisinstelling van dit toestel
(zie bladzijde de Gebruiksaanwijzing). De
subwoofer weergave van dit toestel is in mono.
Bij gebruik van een subwoofer van 70 W
(2 ), moet u erop letten dat u de aansluiting
verricht met de paarse en paars/zwarte
draden van dit toestel. Sluit niets aan op de
groene en groen/zwarte draden.
41. Microfoon
Примечание
Когда данное устройство устанавливается
в транспортном средстве без ACC
(вспомогательные приборы) положения на
замке зажигания, красный кабель должен быть
подключен к клемме, которая может обнаружить
работу замка зажигания. Иначе, в результате
батарея может разрядиться.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
АСС положение
АСС положение нет
Использование данного устройства в иных,
чем следующие условия, может привести к
возгоранию или неправильному срабатыванию.
Автомобиль батареей с 12-вольт и
отрицательным заземлением.
Динамики с 50 Вт (выходная величина) и от 4
ОМ до 8 ОМ (полное сопротивление).
Чтобы предотвратить короткое замыкание,
перегрев или неправильное срабатывание
убедитесь, что следуете указаниям ниже.
Отсоедините отрицательную клемму батареи
пред установкой.
Закрепите провода кабельными зажимами
или липкой лентой. Для защиты проводов
следует обмотать их липкой летной в
тех местах, где они соприкасаются с
металлическими частями.
Прокладывайте все кабели вдали от
двигающихся частей, таких как рычаг
переключения коробки передач или
направляющая для выдвижения сиденья.
Прокладывайте все кабели вдали от
горячих мест, таких как рядом с выпуском
нагревателя.
Не пропускайте желтый кабель через
отверстие в моторном отсеке, для того чтобы
подключить его к батарее.
Защитите все неподключенные кабели
разъемами с изоляционной лентой.
Не укорачивайте какие-либо кабели.
— Никогда не обрезайте изоляцию питающего
кабеля данного устройства, чтобы подключить
питание на другое оборудование. Пропускная
способность кабеля ограничена.
Используйте плавкий предохранитель
заданного номинала.
Никогда не подключайте отрицательный
кабель динамика напрямую к заземлению.
Никогда не связывайте вместе различные
отрицательные кабели динамиков.
Контрольный сигнал выходит по сине/белому
кабелю, когда данное устройство подключено
к электропитанию. Подключите его к системе
дистанционного управления внешнего усилителя
мощности или к клемме управляющего реле
автомобильной антенны (макс. 300 мА, 12 В
пост. ток). Если автомобиль снабжен стеклянной
антенной, подключите её к питающему терминалу
антенного усилителя.
Никогда не подключайте сине/белый кабель
к питающему терминалу внешнего усилителя
мощности. Так же, никогда не подключайте его к
питающему терминалу автомобильной антенны.
Иначе, в результате батарея разрядится или
будет происходить неправильное срабатывание.
IP-BUS соединители с цветовым кодированием.
Будьте уверены, что соединяете соединители
одинакового цвета среди соединителей с
цветовым кодированием.
Черный кабель – заземление. Этот кабель и
кабели заземления других изделий (особенно,
сильноточные изделия, такие как усилитель
мощности) должны быть проложены раздельно.
Иначе, в результате может произойти возгорание
или неправильное срабатывание, если они
внезапно отсоединятся.
СхемаСоединений
1. USB кабель
Подключить к отдельно продающемуся
устройству USB.
2. В
ход микрофона
3. Гнездо AUX (3.5 φ)
Используйте стереокабель с мини-штекером для
подключения вспомогательной аппаратуры.
4. Дист
анционный монтажный вход
Адаптер жестко смонтированного
дистанционного управления может быть
подключен (продается отдельно).
5. Разъем для подключения IP-BUS (голубой)
6. Гнездо антенны
7. Задний выход
8. Передний выход
9.
Выход низкочастотного динамика
10. Данное устройство
11. Кабель IP-BUS
12. Многодисковый проигрыватель (продается
отдельно)
13. Примечание
В зависимости от типа автомобиля функции
3* и 5* могут быть различными. В этом
случае, убедитесь, что 2* подключили к 5* и
4* к 3*.
14. Соедините провода одинакового цвета друг с
другом.
15. К
олпачок (1*)
Не снимайте колпачок, если клемма не
используется.
16. Плавкий предохранитель (10 A)
17. Желтый (3*)
Разрывный (или вспомогательный)
18. Желтый (2*)
Подключите к клемме постоянно подающей
12 В.
19. Резистор предохранителя
20. Красный (5*)
Вспомогательный (или разрывный)
21. Красный (4*)
Подключите к клемме, контролируемой
замком зажигания (12 В пост. ток).
22. Черный (заземление на массу)
Подключите к чистому, неокрашенному
металлическому участку.
23. ISO разъем
Примечание
В некоторых автомобилях ISO разъем
может быть разделен на два. В этом случае
убедитесь, что подключили оба разъема.
24. Синий/белый
Подключите к клемме системы контроля
усилителя мощности (макс. 300 мА 12 В пост.
ток).
25. Синий/белый (7*)
Подключите к клемме управления реле
автомобильной антенны (макс. 300 мА 12 В
пост. ток).
26. Синий/белый (6*)
Расположение штырей ISO разъема может
быть различным в зависимости от типа
автомобиля. Соедините 6* и 7* когда штырь
5 это штырь типа управления антенны.
В других типах автомобилей никогда не
соединяйте 6* и 7*.
27. Провода динамиков
Белый: Передний левый +
Белый/черный: Передний левый
*
Серый: Передний правый +
Серый/черный: Передний правый
*
Зеленый: Задний левый + или
низкочастотный динамик +
Зе
леный/черный: Задний левый
* или
низкочастотный динамик
*
Фиолетовый: Задний правый + или
низкочастотный динамик +
Фио
летовый/черный: Задний правый
*
или низкочастотный
динамик
*
28. К заднему выходу
29. К переднему выходу
30. К заднему выходу низкочастотного динамика
31. Соедините с кабелями RCA (продаются
отдельно)
32. У
силитель мощности (продается отдельно)
33. Система дистанционного управления
34. Левый
35. Правый
36. Низкочастотный динамик
37. Передний динамик
38. Задний динамик
39. Выполните данные подключения, когда
используется усилитель, который не входит в
состав обязательного оборудования.
40. Примечание
Измените исходные настройки данного
устройства (См. Руководство по
эксплуатации). Низкочастотный динамик
данного устройства обеспечивает
монофонический выходной сигнал.
Когда используется Низкочастотный
динамик 70 Вт (2
), будьте уверены,
что соединили Фиолетовый провод с
Фиолетово/Черным проводом данного
устройства. Ничего не соединяйте с
Зеленым проводом и Зелено/Черным
проводом.
41. Микрофон

Transcripción de documentos

CD RDS RECEIVER REPRODUCTOR DE CD CON RECEPTOR RDS CD RDS-EMPFÄNGER AUTORADIO CD RDS SINTOLETTORE CD RDS CD RDS-ONTVANGER CD RDS ПРИЕМНИК  3   DEH-P7100BT Fig. 1 Abb. 1 Afb. 1 Fig. 3 Abb. 3 Afb. 3  Fig. 5 Abb. 5 Afb. 5 Fig. 7 Abb. 7 Afb. 7 9 2 1 Installation Manual Manual de instalación Installationsanleitung Manuel d’installation Manuale d’installazione Installatiehandleiding Руководство по установке Printed in Thailand Imprimé en Thaïlande <0G020029A/N> EW <KOMZX> <08L00000>  10cm 10cm a Fig. 2 Abb. 2 Afb. 2 Fig. 4 Abb. 4 Afb. 4 Fig. 6 Abb. 6 Afb. 6 b Fig. 8 Abb. 8 Afb. 8 Installation Note • Check all connections and systems before final installation. • Do not use unauthorized parts. The use of unauthorized parts may cause malfunctions. • Consult with your dealer if installation requires drilling of holes or other modifications of the vehicle. • Do not install this unit where: — it may interfere with operation of the vehicle. — it may cause injury to a passenger as a result of a sudden stop. • The semiconductor laser will be damaged if it overheats. Install this unit away from hot places such as near the heater outlet. • Optimum performance is obtained when the unit is installed at an angle of less than 60°. (Fig. 1) • When installing, to ensure proper heat dispersal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents. (Fig. 2) 1 Leave ample space 2 Dashboard • The cords must not cover up the area shown in the figure. This is necessary to allow the amplifires to radiate freely. (Fig. 3) 3 Do not cover this area. DIN Front/Rear-mount This unit can be properly installed either from “Front” (conventional DIN Front-mount) or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit chassis). For details, refer to the following installation methods. Removing or attaching the trim ring 1. Extend top and bottom of the trim ring outwards to remove the trim ring. (Fig. 4) • When reattaching the trim ring, push the trim ring onto the unit until it clicks. (If the trim ring is attached upside down, the trim ring will not fit properly.) • It becomes easy to remove the trim ring if the front panel is released. 4 Trim ring DIN Front-mount Installation with the rubber bush 1. Insert the mounting sleeve into the dashboard. English • When installing in a shallow space, use a supplied mounting sleeve. If there is enough space behind the unit, use factory supplied mounting sleeve. 2. Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place. 3. Install the unit as illustrated. (Fig. 5) 5 Dashboard 6 Mounting sleeve 7 Rubber bush 8 Screw Removing the Unit 1. Insert the supplied extraction keys into both sides of the unit until they click into place. (Fig. 6) 2. Pull the unit out of the dashboard. DIN Rear mount 1. Determine the appropriate position where the holes on the bracket and the side of the unit match. (Fig. 7) 2. Tighten two screws on each side. (Fig. 8) • Use either truss screws (5 mm × 8 mm) or flush surface screws (5 mm × 9 mm), depending on the shape of screw holes in the bracket. 9 Screw a Factory radio mounting bracket b Dashboard or Console Fastening the front panel If you do not plan to detach the front panel, the front panel can be fastened with supplied screws and holders. 1. Attach the holders to both sides of the front panel. (Fig. 9) c Holder 2. Replace the front panel to the unit. (Fig. 10) 3. Flip the holders into upright positions. (Fig. 11) 4. Fix the front panel to the unit using screws. (Fig. 12) d Screw Instalación Nota • Verifique todas las conexiones y sistemas antes de la instalación final. • No utilice piezas no autorizadas. El uso de piezas no autorizadas puede causar un fallo de funcionamiento. • Consulte su revendedor si se requiere taladrar agujeros o hacer otras modificaciones del vehículo para la instalación. • No instale esta unidad donde: — pueda interferir con la operación del vehículo. — pueda causar lesiones a un pasajero en el caso de una parada brusca. • El láser semiconductor se dañará si se sobrecalienta. Instale esta unidad alejada de lugares calientes como cerca de la salida del calentador. • Se obtiene el rendimiento óptimo cuando se instala la unidad en un ángulo inferior a 60°. (Fig. 1) • Cuando instale, para asegurar la dispersión apropiada del calor durante el uso de esta unidad, asegúrese de dejar un amplio espacio por detrás del panel trasero y enrolle cualesquiera cables sueltos de modo que no bloqueen las aberturas de ventilación. (Fig. 2) 1 Deje un amplio espacio 2 Tablero de instrumentos • Los cordones no deben tapar el área mostrado en la figura. Esto es necesario para permitir que los amplificadores puedan radiar libremente. (Fig. 3) 3 No cubra esta área. Montaje delantero/trasero DIN Se puede instalar esta unidad apropiadamente mediante el montaje “delantero” (montaje delantero DIN convencional) o montaje “trasero” (montaje trasero DIN utilizando los agujeros de tornillo roscados en los lados del bastidor de la unidad). Para los detalles, consulte los siguientes métodos de instalación. Extracción o instalación del anillo compensación 1. Extienda las partes superior e inferior del anillo de compensación hacia fuera para extraer el anillo de compensación. (Fig. 4) • Cuando reinstale el anillo de compensación, empuje el anillo de compensación en la unidad hasta que encaje con un “clic”. (Si se instala el anillo de compensación invertido, puede que el anillo de compensación no se encaje correctamente.) • Se hace más fácil quitar el anillo de compensación si se suelta el panel delantero. 4 Anillo de compensación Montaje delantero DIN Instalación con el buje de caucho 1. Inserte el manguito de montaje en el tablero de instrumentos. Español • Cuando instale en un lugar poco profundo, utilice el manguito de montaje suministrado. Si hay espacio suficiente detrás de la unidad, utilice el manguito de montaje suministrado de fábrica. 2. Fije el manguito de montaje utilizando un destornillador para doblar las lengüetas de metal (90°) en posición. 3. Instale la unidad como se muestra. (Fig. 5) 5 Tablero de instrumentos 6 Manguito de montaje 7 Buje de caucho 8 Tornillo Extracción de la unidad 1. Inserte las llaves de extracción suministradas en ambos lados de la unidad hasta que se enganchen en posición. (Fig. 6) 2. Tire de la unidad del tablero de instrumentos. Montaje trasero DIN 1. Determine la posición apropiada donde los agujeros en la ménsula y el lado de la unidad se emparejan. (Fig. 7) 2. Apriete los dos tornillos en cada lado. (Fig. 8) • Utilice tornillos con cabeza ovalada (5 mm × 8 mm) o tornillos de cabeza embutida (5 mm × 9 mm), dependiendo de la forma de los agujeros de tornillo en la ménsula. 9 Tornillo a Ménsula de montaje de radio de fábrica b Tablero de instrumentos o consola Fijación del panel delantero Si no planea extraer el panel delantero, se puede fijar el panel delantero con los tornillos y sujetadores suministrados. 1. Coloque los sujetadores en ambos lados del panel delantero. (Fig. 9) c Sujetador 2. Reinstale el panel delantero en la unidad. (Fig. 10) 3. Mueva los sujetadores en las posiciones verticales. (Fig. 11) 4. Fije el panel delantero a la unidad utilizando los tornillos. (Fig. 12) d Tornillo Einbau Hinweise • Überprüfen Sie alle Anschlüsse und Systeme, bevor Sie das Gerät endgültig einbauen. • Verwenden Sie keine unautorisierten Teile. Die Verwendung von unautorisierten Teilen kann zu Funktionsstörungen führen. • Wenden Sie sich an Ihren Fachhändler, wenn zum Einbau des Geräts Löcher gebohrt oder andere Veränderungen an Ihrem Auto vorgenommen wenden müssen. • Bauen Sie das Gerät nicht an einer Stelle ein, wo: — es den Fahrer beim Fahren behindert. — es den Beifahrer bei plötzlichem Bremsen verletzen kann. • Der Halbleiterlaser wird bei Überhitzung beschädigt. Bauen Sie das Gerät daher nicht an einer Stelle ein, wo es heiß wird, z. B. in der Nähe einer Heizungsauslassöffnung. • Die optimale Leistung wird erzielt, wenn der Einbauwinkel nicht mehr als 60° beträgt. (Abb. 1) • Damit die bei Betrieb dieses Geräts entwickelte Wärme richtig abgeleitet werden kann, sorgen Sie beim Einbau dafür, dass ausreichend Platz hinter der Rückwand bleibt, und wickeln Sie lockere Kabel so, dass diese keine Öffnungen blockieren können. (Abb. 2) 1 Reichlich Platz lassen 2 Armaturenbrett • Die Leitungen dürfen den in der Abbildung gezeigten Bereich nicht verdecken. Dies ist erforderlich, damit die Verstärker frei Wärme abstrahlen können. (Abb. 3) 3 Diesen Bereich nicht verdecken. DIN Einbau an der Vorderseite/Rückseite Dieses Gerät kann entweder an der “Vorderseite” (herkömmliche DIN Einbau an der Vorderseite) oder an der “Rückseite” (DIN Einbau an der Rückseite mit Hilfe der Löcher für die Gewindeschrauben, die sich an der Seite des Geräte-Chassis befinden) eingebaut werden. Einzelheiten entnehmen Sie bitte den folgenden Einbaumethoden. Abnehmen und Anbringen des Zierleistenrings 1. Ziehen Sie den Zierleistenring an der Ober- und Unterseite nach außen, um den Ring zu entfernen. (Abb. 4) • Beim erneuten Anbringen des Zierleistenrings drücken Sie den Ring auf das Gerät, bis er einrastet. (Falls der Zierleistenring verkehrt herum angebracht wird, passt er nicht richtig.) • Wenn die Frontplatte freigegeben ist, ist es ganz einfach, den Zierleistenring abzunehmen. 4 Zierleistenring DIN Einbau an der Vorderseite Einbau mit der Gummibuchse 1. Setzen Sie den Halter in das Armaturenbrett ein. Deutsch • Verwenden Sie beim Einbau an einer engen Stelle einen mitgelieferten Halter. Wenn nicht genügend Platz hinter dem Gerät vorhanden ist, verwenden Sie den vom Werk mitgelieferten Halter. 2. Befestigen Sie den Halter mit Hilfe eines Schraubendrehers, um die Metalllaschen um 90° zu verbiegen. 3. Bauen Sie das Gerät wie gezeigt ein. (Abb. 5) 5 Armaturenbrett 6 Halter 7 Gummibuchse 8 Schraube Ausbauen des Geräts 1. Setzen Sie die mitgelieferten Ausziehschlüssel auf beiden Seiten bis zur Einrastposition in das Gerät ein. (Abb. 6) 2. Ziehen Sie das Gerät aus dem Armaturenbrett. DIN Einbau an der Rückseite 1. Bestimmen Sie die geeignete Position, wo die Löcher in der Konsole und an der Geräteseite übereinstimmen. (Abb. 7) 2. Ziehen Sie zwei Schrauben auf jeder Seite fest. (Abb. 8) • Verwenden Sie entweder Flachrundkopfschrauben (5 mm × 8 mm) oder Schrauben mit bündiger Oberfläche (5 mm × 9 mm), je nach der Art der Schraubenlöcher in der Konsole. 9 Schraube a Vom Werk mitgelieferter Radio-Befestigungsbügelavec la voiture b Armaturenbrett oder Konsole Befestigung der Frontplatte Falls Sie nicht beabsichtigen, die Frontplatte abzunehmen, kann sie mit den mitgelieferten Schrauben und Haltern befestigt werden. 1. Bringen Sie die Halter an beiden Seiten der Frontplatte an. (Abb. 9) c Halter 2. Bringen Sie die Frontplatte weider am Gerät an. (Abb. 10) 3. Klappen Sie die Halter hoch. (Abb. 11) 4. Sichern Sie die Frontplatte mit den Schrauben am Gerät. (Abb. 12) d Schraube Installation Remarque • Vérifiez toutes les connexions et tous les systèmes avant l’installation finale. • N’utilisez aucune pièce non autorisée. L’utilisation de pièces non autorisées peut causer un mauvais fonctionnement. • Consultez votre revendeur si l’installation nécessite que vous perciez des trous ou effectuiez d’autres modifications du véhicule. • N’installez pas l’appareil dans un endroit où: — il peut gêner la conduite du véhicule. — il peut causer des blessures à un passager à la suite d’un arrêt brutal. • Le laser à semi-conducteur sera endommagé en cas de surchauffe. Installez cet appareil à l’écart des endroits chauds tels que près de la sortie du chauffage. • Des performances optimales peuvent être obtenues quand l’appareil est installé avec un angle de moins de 60°. (Fig. 1) • Lors de l’installation de l’appareil, laissez suffisamment d’espace derrière le panneau arrière pour permettre une dissipation correcte de la chaleur et pliez tout câble gênant de façon qu’il n’obstrue pas les orifices de ventilation. (Fig. 2) 1 Laissez suffisamment d’espace 2 Tableau de bord • Les cordons ne doivent pas couvrir la zone montrée sur la figure. C’est nécessaire pour permettre à l’amplificateur de rayonner librement. (Fig. 3) 3 Ne recouvrez pas cette zone. Montage avant/arrière DIN Cet appareil peut être installé correctement par “l’avant” (montage avant conventionnel DIN) ou par “l’arrière” (montage par l’arrière DIN, en utilisant les trous taraudés de chaque côté du châssis). Pour les détails, reportez-vous aux méthodes d’installation suivantes. Retrait ou fixation de la garniture 1. Étendez la partie supérieure et inférieure de la garniture vers l’extérieur pour la retirer. (Fig. 4) • Pour fixer de nouveau la garniture, poussez la garniture sur l’appareil jusqu’à ce qu’elle s’emboîte en produisant un bruit sec. (Si la garniture est fixée à l’envers, elle ne s’emboîte pas correctement.) • Il est plus facile de retirer la garniture quand le panneau avant est détaché. 4 Garniture Montage avant DIN Installation avec l’amortisseur en caoutchouc 1. Insérez le manchon de montage dans le tableau de bord. Français • Si l’installation se fait dans un emplacement étroit, utilisez le manchon de montage fourni. S’il y a suffisamment de place derrière l’appareil, utilisez le manchon de montage fourni avec la voiture. 2. Fixez le manchon de montage en utilisant un tournevis pour tordre les languettes de métal (90°). 3. Installez l’appareil comme montré sur l’illustration. (Fig. 5) 5 Tableau de bord 6 Manchon de montage 7 Amortisseur en caoutchouc 8 Vis Retrait de l’appareil 1. Insérez les clés d’extraction fournies de chaque côté de l’appareil jusqu’à ce que vous entendiez un déclic. (Fig. 6) 2. Tirez l’appareil pour le sortir du tableau de bord. Montage arrière DIN 1. Déterminez la position appropriée dans laquelle les trous du support de montage coïncident avec ceux du côté de l’appareil. (Fig. 7) 2. Serrez deux vis de chaque côté. (Fig. 8) • Utilisez des vis à tête bombée (5 mm × 8 mm) ou des vis à tête encastrée (5 mm × 9 mm), en fonction de la forme des trous dans le support. 9 Vis a Support de montage fourni avec la voiture b Tableau de bord ou console Fixation du panneau avant Si vous ne prévoyez pas de détacher le panneau avant, il peut être fixé avec les vis et les crochets fournis. 1. Attachez les crochets des deux côtés de la face avant. (Fig. 9) c Crochet 2. Remettez la face avant en place sur l’appareil. (Fig. 10) 3. Faites pivoter les crochets en position droite. (Fig. 11) 4. Fixez la face avant sur l’appareil avec les vis. (Fig. 12) d Vis Installazione Nota • Prima dell’installazione finale vi raccomandiamo di verificare tutti i sistemi coinvolti e le relative connessioni. • Non fate mai uso di parti non autorizzate. Esse potrebbero infatti dar luogo a malfunzionamenti. • Qualora l’installazione richieda l’esecuzione di fori oppure di modifiche al veicolo, rivolgetevi innanzi tutto al vostro rivenditore. • Non installate questa unità ove: — possa interferire con la guida del veicolo. — possa causare il ferimento dei passeggeri in caso di brusca frenata. • Il laser a semiconduttore si potrebbe danneggiare in caso di surriscaldamento. Installate pertanto l’unità lontano dai punti ad elevata temperatura quali, ad esempio, gli effusori del sistema di riscaldamento del veicolo. • Le prestazioni migliori si ottengono quando s’installa l’unità secondo un angolo di ampiezza inferiore a 60°. (Fig. 1) • Per assicurare un’adeguata dispersione del calore dell’apparecchio nel corso del suo utilizzo, durante l’installazione si raccomanda di lasciare ampio spazio dietro il pannello posteriore e di avvolgere i cavi allentati affinché non ostruiscano le bocche di ventilazione. (Fig. 2) 1 Lasciare ampio spazio 2 Cruscotto • I cavi non devono coprire la zona mostrata nella figura: l’amplificatore deve essere in grado di diffondere il suono liberamente. (Fig. 3) 3 Non ostruire quest’area. Installazione DIN frontale/ posteriore L’unità può essere correttamente installata sia su “frontalmente” (normale installazione DIN frontale) sia “posteriormente” (installazione DIN posteriore impiegando i fori filettati ubicati sui lati del telaio). Le sezioni che seguono offrono informazioni dettagliate sui due metodi d’installazione. Rimozione o applicazione del bordo di rifinitura 1. Tirate verso l’esterno le parti superiore e inferiore del bordo di rifinitura in modo da rimuoverlo. (Fig. 4) • Per rimontarlo premetelo nell’unità sino ad avvertirne lo scatto in posizione (non s’inserisce correttamente se si tenta di montarlo capovolto). • La rimozione del bordo di rifinitura risulta più facile quando si rimuove il pannello anteriore. 4 Bordo di rifinitura Installazione DIN frontale Installazione con la guaina di gomma 1. Inserite nel cruscotto il telaio d’installazione. Italiano • Il telaio d’installazione va usato in caso d’installazione in un punto poco profondo. Qualora posteriormente all’unità vi sia sufficiente spazio è raccomandabile impiegare il telaio d’installazione del costruttore. 2. Fissate il telaio d’installazione usando un cacciavite col quale piegare in posizione (di 90°) le linguette metalliche. 3. Installate l’unità nel modo mostrato. (Fig. 5) 5 Cruscotto 6 Telaio d’installazione 7 Guaina di gomma 8 Vite Rimozione dell’unità 1. Inserite in entrami i lati dell’unità le apposite chiavi di estrazione sino ad avvertirne lo scatto in posizione. (Fig. 6) 2. Estraete l’unità dal cruscotto. Installazione DIN posteriore 1. Determinate il punto esatto in cui i fori della staffa e quelli ubicati ai lati dell’unità coincidono. (Fig. 7) 2. Serrate bene due viti di entrambi i lati. (Fig. 8) • In funzione della forma dei fori filettati della staffa usate viti a trave (5 mm × 8 mm) oppure viti incassate (5 mm × 9 mm). 9 Vite a Staffa di montaggio radio del costruttore b Cruscotto o console centrale Fissaggio del pannello anteriore Qualora non intendiate separare il pannello anteriore, esso può essere perennemente fissato con le viti e i supporti forniti in dotazione. 1. Assicurare i supporti di fissaggio ad entrambi i lati del pannello anteriore. (Fig. 9) c Supporto 2. Rimontare il pannello anteriore sull’unità. (Fig. 10) 3. Ruotare i supporti nelle posizioni vertiali. (Fig. 11) 4. Bloccare il pannello anteriore all’unità per mezzo delle apposite viti. (Fig. 12) d Vite Installatie Opmerking • Controleer alle aansluitingen en systemen voor de uiteindelijke installatie. • Gebruik geen ongeautoriseerde onderdelen. Gebruik van niet-goedgekeurde onderdelen kan leiden tot storingen. • Raadpleeg uw dealer als u voor de installatie gaten moet boren of andere wijzigingen aan het voertuig zelf moet aanbrengen. • Installeer dit toestel in geen geval op een locatie waar: — het de besturing van het voertuig kan hinderen. — het een passagier zou kunnen verwonden bij een noodstop. • De halfgeleider laser zal kapot gaan als deze oververhit raakt. Installeer dit toestel niet in de buurt van zeer warme plekken, zoals bij een verwarmingsrooster. • De optimale prestaties worden verkregen wanneer het toestel geïnstalleerd wordt onder een hoek van minder dan 60º. (Afb. 1) • Om verzekerd te kunnen zijn van voldoende ventilatie bij gebruik van dit toestel, dient u er bij de installatie voor te zorgen dat u achter het achterpaneel en rondom het toestel voldoende ruimte vrij laat, en dient u eventuele losse bedrading samen te bundelen zodat deze de ventilatie-openingen niet kan blokkeren. (Afb. 2) 1 Laat voldoende ruimte vrij 2 Dashboard • Let erop dat de snoeren niet het gedeelte bedekken dat is aangegeven in de afbeelding. Dit om te voorkomen dat de ventilatie van de versterker wordt belemmerd. (Afb. 3) 3 Deze plek niet afdekken. DIN Voor/achter montage Dit toestel kan op de juiste manier worden vastgemaakt aan de voorkant (conventionele DIN montage) of aan de achterkant (DIN achtermontage, met behulp van de schroefgaatjes aan de zijkanten van het chassis van het toestel). Voor details verwijzen we u naar de volgende installatiemethoden. Verwijderen of bevestigen van de afwerkingsrand. 1. Buig de bovenkant en de onderkant van de afwerkingsrand naar buiten om deze te verwijderen. (Afb. 4) • Druk de afwerkingsrand op het toestel tot deze vastklikt wanneer u de afwerkingsrand weer vast maakt. (Als de afwerkingsrand ondersteboven gehouden wordt, zal deze niet goed passen.) • De afwerkingsrand is makkelijker los te maken wanneer het voorpaneel verwijderd is. 4 Afwerkingsrand DIN Voor-montage Installatie met het rubber tussenstuk 1. Steek de bevestigingskraag in het dashboard. Nederlands • Gebruik een andere bevestigingskraag bij installatie op een relatief ondiepe locatie. Als er genoeg ruimte achter het toestel is, kunt u de standaard meegeleverde bevestigingskraag gebruiken. 2. Zet de bevestigingskraag vast door met behulp van een schroevendraaier de metalen lipjes te verbuigen (90°). 3. Installeer het toestel zoals u kunt zien op de afbeelding. (Afb. 5) 5 Dashboard 6 Bevestigingskraag 7 Rubber tussenstuk 8 Schroef Verwijderen van het toestel 1. Steek de meegeleverde ontgrendelingsstrips in beide zijkanten van het toestel tot deze vastklikken. (Afb. 6) 2. Trek het toestel uit het dashboard. DIN Achter-montage 1. Bepaal welke gaatjes in de beugel en in de zijkant van het toestel met elkaar overeenkomen. (Afb. 7) 2. Gebruik twee schroeven aan elke kant. (Afb. 8) • Gebruik schroeven met platte kop (5 mm × 8 mm) of verzinkbare kop (5 mm × 9 mm), afhankelijk van de vorm van de schroefgaatjes in de beugel. 9 Schroef a Fabrieksmontagebeugel of-steun voor bevestiging radio e.d. b Dashboard of console Vastzetten van het voorpaneel Als u het voorpaneel niet wilt kunnen verwijderen, kunt u het vastzetten met de daartoe meegeleverde schroeven en houders. 1. Bevestig de houders aan beide zijden van het voorpaneel. (Afb. 9) c Houder 2. Plaats het voorpaneel weer op het toestel. (Afb. 10) 3. Klap de houders overeind. (Afb. 11) 4. Bevestig het voorpaneel met de schroeven aan het toestel. (Afb. 12) d Schroef Установка Примечание • Проверьте все соединения и системы перед окончательной установкой. • Не используйте неразрешенные части. Использование неразрешенных частей может стать причиной неисправной работы. • Проконсультируйтесь с вашим дилером, если установка требует просверливания отверстий или других модификаций вашего транспортного средства. • Не устанавливайте устройство там, где: — оно может служить препятствием работы транспортного средства. — оно может стать причиной повреждения пассажира в результате внезапной остановки. • Полупроводниковый лазер будет поврежден, если он перегреется. Устанавливайте данное устройство вдали от горячих мест, таких как рядом с выпуском нагревателя. • Оптимальное изображение не получается, когда устройство установлено под углом меньше чем 60°. (Рис. 1) • При установке, после подтверждения подходящего рассеивания тепла при использовании этого устройства, пожалуйста, удостоверьтесь, что вы оставляете прострное место позади адней панели и, пожалуйста, сверните любые неприкрепленные кабели так, чтобы они не смогли заблокировать вентиляционное отверстие. (Рис. 2) 1 Оставить просторное место 2 Пeрeдняя панель • Провода не должны закрывать зоны, показанные на рисунке. Это необходимо для свободного рассеивания тепла, излучаемого усилителями. (Рис. 3) 3 Не закрывайте эту область. Переднее/Заднее крепление по стандарту DIN Крепление данного устройства можно выполнять как “спереди” (стандартное переднее крепление DIN), так и “сзади” (заднее крепление DIN с использованием резьбовых отверстий для винтов, расположенных по бокам рамы устройства). Более подробная информация приведена ниже в иллюстрированном описании методов установки. Удаление или прикрепление ластичного ободка 1. Оттяните верх и низ ластичного ободка наружу, чтобы вытащить его. (Рис. 4) • Когда повторно присоединяете ластичный ободок, вдавите его в устройство, пока он не щелкнет. (Если ластичный ободок присоединен верхней стороной вниз, то он не будет подогнан должным образом.) • Вытащить ластичный ободок легче, если передняя панель опущена. 4 Ластичный ободок Переднее крепление по стандарту DIN Установка с резиновой втулкой Pyccкий 1. Вставьте монтажный рукав в переднюю панель. • Когда устанавливаете в неглубокое пространство, используйте предусмотренный монтажный рукав. Если позади устройства имеется достаточное пространство, используйте предусмотренный заводом монтажный рукав. 2. Закрепите монтажный рукав, используя отвертку, чтобы согнуть металлические ушки (90°) на место. 3. Установите устройство как показано на иллюстрации. (Рис. 5) 5 6 7 8 Передняя панель Монтажный рукав Резиновая втулка Винт Удаление Устройства 1. Вставьте предусмотренные ключи для извлечения в обе стороны устройства, пока они не защелкнутся на место. (Рис. 6) 2. Вытяните устройство из передней панели. Заднее крепление по стандарту DIN 1. Подберите подходящее место, где отверстия на скобе и стороне устройства будут совпадать. (Рис. 7) 2. Затяните два винта на каждой стороне. (Рис. 8) • Используйте винты со сферической головкой (5 мм × 8 мм) или винты с потайной головкой (5 мм × 9 мм), в зависимости от формы отверстий в скобе. 9 Винт a Заводская скоба для крепления радиоприемника b Передняя панель или консоль Закрепление передней панели Если вы не планируете отсоединять переднюю панель, то она может быть закреплена с помощью поставляемых винтов и держателей. 1. Закрепите держатели с обеих сторон передней панели. (Рис. 9) c Держатель 2. Приложите переднюю панель к устройству. (Рис. 10) 3. Переверните держатели в вертикальное положение. (Рис. 11) 4. Прикрепите переднюю панель к устройству, используя винты. (Рис. 12) d Винт Installation � Fig. 1 � Abb. 1 Afb. 1 Рис. 1 English Installing the microphone Install the microphone in a position and orientation that will enable it to pick up the voice of the person operating the system. CAUTION • It is extremely dangerous to allow the microphone lead to become wound around the steering column or gearstick. Be sure to install the unit in such a way that it will not obstruct driving.  Fig. 2 Abb. 2  Afb. 2 Рис. 2 When installing the microphone on the sun visor 1. Install the microphone on the microphone clip. (Fig. 1) 1 Microphone 2 Microphone clip 2. Install the microphone clip on the sun visor. (Fig. 2)  Fig. 3  Abb. 3   Abb. 3 Рис. 3 • With the sun visor up, install the microphone clip. (Lowering the sun visor reduces the voice recognition rate.) 3 Microphone clip 4 Clamp Use separately sold clamps to secure the lead where necessary inside the vehicle. When installing the microphone on the steering column  Fig. 4 Abb. 4 A Abb. 4 Рис. 4 Fig. 5 Abb. 5 B Abb. 5 Рис. 5 Fig. 6 Abb. 6 Abb. 6 Рис. 6 1. Install the microphone on the microphone clip. (Fig. 3) 5 Microphone 6 Microphone base 7 Microphone clip 8 Fit the microphone lead into the groove. • Microphone can be installed without using microphone clip. In this case, detach the microphone base from the microphone clip. To detach the microphone base from microphone clip, slide the microphone base. 2. Install the microphone clip on the steering column. (Fig. 4) (Fig. 5) 9 Double-sided tape a Install the microphone clip on the rear side of the steering column. b Clamp Use separately sold clamps to secure the lead where necessary inside the vehicle. Adjusting the microphone angle (Fig. 6) The microphone angle can be adjusted. Instalación Español Instalación del micrófono Instale el micrófono en una posición u orientación que permita captar bien las voces de la persona que utilice el sistema mediante voz. PRECAUCIÓN Einbau Deutsch Einbau des Mikrofons Das Mikrofon an einem geeigneten Platz anbringen und so ausrichten, dass es die Stimme der Person, die das System über Sprache steuert, gut aufnimmt. VORSICHTSMASSNAHMEN Installation Français Installation du microphone Installez et orientez le microphone à un endroit où il pourra bien capter la voix de la personne qui commande le système par la voix. ATTENTION Installazione Italiano Installazione del microfono Installare il microfono in una posizione e con un orientamento che permettano una buona captazione della voce della persona che controlla il sistema di navigazione tramite la voce. PRECAUZIONE • Es peligrosísimo dejar que el cable del micrófono se enrolle en la base del volante o en la palanca de cambios. Asegúrese de instalar la unidad de forma que ésta no sea un obstáculo para la conducción. • Es ist äußerst gefährlich, das Mikrofonkabel um die Lenksäule oder den Gangschalthebel zu wickeln. Beim Einbau unbedingt darauf achten, dass das Gerät den Fahrer nicht behindert. • Une situation très dangereuse pourrait se présenter si le fil du microphone devait s’enrouler autour de la colonne de direction ou du levier de vitesses. Veillez à cheminer le fil de manière qu’il ne fasse pas obstacle à la conduite. • È estremamente pericoloso lasciare che il cavo del microfono si impigli nella colonna dello sterzo o nella leva del cambio. Assicurarsi di installare l’unità in modo tale da non ostacolare la guida. Cuando instale el micrófono en la visera Befestigung des Mikrofons an der Sonnenblende Installation du microphone sur le pare-soleil Quando si installa il microfono sull’aletta parasole 1. Instale el micrófono en la presilla de micrófono. (Fig. 1) 1 Micrófono 2 Presilla de micrófono 2. Instale la presilla de micrófono en la visera. (Fig. 2) • Con la visera hacia arriba, instale la presilla del micrófono. (Al bajar la visera se reduce la capacidad de reconocimiento de mediante voz). 3 Presilla de micrófono 4 Abrazadera Utilice abrazaderas vendidas separadamente para asegurar el cable en el interior del vehículo donde sea necesario. Cuando instale el micrófono en la base del volante 1. Instale el micrófono en la presilla de micrófono. (Fig. 3) 5 Micrófono 6 Base del micrófono 7 Presilla de micrófono 8 Fije el cable del micrófono en la ranura. • Se puede instalar el micrófono sin utilizar la presilla de micrófono. En este caso, extraiga la base del micrófono de la presilla de micrófono. Para extraer la base del micrófono de la presilla de micrófono, deslice la base del micrófono. 2. Instale la presilla de micrófono en la base del volante. (Fig. 4) (Fig. 5) 9 Cinta con adhesivo de doble cara a Instale la presilla del micrófono en el lado trasero de la base del volante. b Abrazadera Utilice abrazaderas vendidas separadamente para asegurar el cable en el interior del vehículo donde sea necesario. Ajuste del ángulo del micrófono (Fig. 6) Se puede ajustar el ángulo del micrófono. 1. Das Mikrofon im Mikrofonklemmhalter befestigen. (Abb. 1) 1 Mikrofon 2 Mikrofonklemmhalter 2. Den Mikrofonklemmhalter an der Sonnenblende anklemmen. (Abb. 2) • Die Sonnenblende hochklappen und den Mikrofonklemmhalter anklemmen. (Ein Herunterklappen der Sonnenblende verringert die Spracherkennungsrate bei der sprachgesteuerten Bedienung). 3 Mikrofonklemmhalter 4 Kabelklemme Das Mikrofonkabel mit getrennt erhältlichen Kabelklemmen im Fahrzeuginnenraum verlegen. Befestigung des Mikrofons an der Lenksäule 1. Das Mikrofon im Mikrofonklemmhalter befestigen. (Abb. 3) 5 Mikrofon 6 Mikrofon-Unterlage 7 Mikrofonklemmhalter 8 Das Mikrofonkabel in die Kerbe einpassen. • Das Mikrofon kann ohne den Mikrofonklemmhalter installiert werden. Nehmen Sie die Mikrofon-Unterlage in diesem Fall vom Mikrofonklemmhalter ab. Um die Mikrofon-Unterlage vom Mikrofonklemmhalter abzunehmen, verschieben Sie sie einfach. 2. Das Mikrofon an der Lenksäule befestigen. (Abb. 4) (Abb. 5) 9 Doppelseitiger Klebestreifen a Den Mikrofonklemmhalter an der Rückseite der Lenksäule befestigen. b Kabelklemme Das Mikrofonkabel mit getrennt erhältlichen Kabelklemmen im Fahrzeuginnenraum verlegen. Einstellung des Mikrofonwinkels (Abb. 6) Der Mikrofonwinkel kann eingestellt werden. 1. Fixez le microphone sur l’attache fournie. (Fig. 1) 1 Microphone 2 Attache 2. Fixez l’attache du microphone sur le pare-soleil. (Fig. 2) • Le pare-soleil étant relevé, fixez l’attache du microphone. (Le taux de reconnaissance vocale diminue quand le pare-soleil est abaissé.) 3 Attache de microphone 4 Serre-fils Utilisez des serre-fils vendus séparément pour fixer le fil conducteur aux endroits nécessaires dans le véhicule. Installation du microphone sur la colonne de direction 1. Fixez le microphone sur l’attache fournie. (Fig. 3) 5 Microphone 6 Base du microphone 7 Attache 8 Cheminez le fil du microphone dans la rainure. • Le microphone peut être installé sans utiliser l’attache du microphone. Dans ce cas, détachez la base du microphone de l’attache. Pour détacher la base du microphone de l’attache, faites glisser la base du microphone. 2. Fixez l’attache du microphone sur la colonne de direction. (Fig. 4) (Fig. 5) 9 Bande adhésive double face a Installez l’attache de microphone sur l’arrière de la colonne de direction. b Serre-fils Utilisez des serre-fils vendus séparément pour fixer le fil conducteur aux endroits nécessaires dans le véhicule. Ajustement de l’angle du microphone (Fig. 6) L’angle du microphone peut être. 1. Installare il microfono sul gancio microfono. (Fig. 1) 1 Microfono 2 Gancio microfono 2. Installare il gancio microfono sull’aletta parasole. (Fig. 2) • Installare il gancio microfono tenendo l’aletta parasole alzata. (Abbassando l’aletta parasole si riduce il tasso di riconoscimento dei comandi vocali.) 3 Gancio microfono 4 Morsetti Usare dei morsetti (da reperire in commercio) per fissare il cavo nei punti necessari all’interno del veicolo. Quando si installa il microfono sulla colonna dello sterzo 1. Installare il microfono sul gancio microfono. (Fig. 3) 5 Microfono 6 Base del microfono 7 Gancio microfono 8 Far passare il cavo del microfono nella scanalatura. • Il microfono può essere installato anche senza usare l’apposito gancio. In tal caso occorre rimuovere la base da quest’ultimo semplicemente facendola scorrere 2. Installare il gancio microfono sulla colonna dello sterzo. (Fig. 4) (Fig. 5) 9 Nastro biadesivo a Installare il gancio microfono sul retro della colonna dello sterzo. b Morsetti Usare dei morsetti (da reperire in commercio) per fissare il cavo nei punti necessari all’interno del veicolo. Regolazione dell’angolo del microfono (Fig. 6) L’angolo del microfono è regolabile. Installatie Nederlands Bevestigen van de microfoon Monteer de microfoon op een plaats en in de richting waarin deze het stemgeluid van de persoon die het systeem via spraak bedient goed kan opvangen. BELANGRIJK • Wanneer de microfoondraad zich rond de stuurkolom of de versnellingspook wikkelt, ontstaat een bijzonder gevaarlijke situatie. Let er bij het aanbrengen van de microfoon op dat u op geen enkele wijze gehinderd wordt bij de normale besturing van de auto. Bevestigen van de microfoon op de zonneklep 1. Monteer de microfoon in de microfoonclip. (Afb. 1) 1 Microfoon 2 Microfoonclip 2. Monteer de microfoonclip op de zonneklep. (Afb. 2) • Bevestig de microfoonclip op de omhooggeklapte zonneklep. (Bij het omlaagklappen van de zonneklep zal het stemherkenningsvermogen van de microfoon afnemen.) 3 Microfoonclip 4 Klem Klemmen om de draad op de vereiste plaatsen tegen het interieur van de auto te bevestigen. Bevestigen van de microfoon op de stuurkolom 1. Monteer de microfoon in de microfoonclip. (Afb. 3) 5 Microfoon 6 Microfoonvoet 7 Microfoonclip 8 Laat de microfoondraad via de groef lopen. • De microfoon kan worden bevestigd zonder gebruik te maken van de microfoonclip. Haal in dit geval de voet van de microfoonclip. Schuif de voet van de microfoonclip om deze los te maken. 2. Bevestig de microfoonclip op de stuurkolom. (Afb. 4) (Afb. 5) 9 Dubbelzijdig plakband a Bevestig de microfoonclip op de bovenkant van de stuurkolom. b Klem Klemmen om de draad op de vereiste plaatsen tegen het interieur van de auto te bevestigen. Instellen van de hoek van de microfoon (Afb. 6) De hoek van de microfoon kan worden ingesteld. Установка Русский Установка микрофона Установите микрофон в позицию и ориентируйте его так, чтобы он мог улавливать голос человека, который оперирует системой. ОСТОРОЖНО • Чрезвычайно опасно позволять проводам микрофона обвиваться вокруг рулевой колонки или рычага передач. Убедитесь, что установили устройство таким образом, что оно не будет затруднять движение. Когда микрофон установлен на солнцезащитном козырьке 1. Установка микрофона на микрофонном зажиме. (Рис. 1) 1 Микрофон 2 Микрофонный зажим 2. Установка микрофонного зажима на солнцезащитном козырьке. (Рис. 2) • Наверху солнцезащитного козырька установите микрофонный зажим. (Опускание солнцезащитного козырька уменьшает степень распознавания голоса для оперирующего голоса.) 3 Микрофонный зажим 4 Скобы Используйте скобы для крепления проводов внутри машины, где это необходимо. Когда микрофон установлен на рулевой колонке 1. Установка микрофона на микрофонном зажиме. (Рис. 3) 5 Микрофон 6 Основание микрофона 7 Микрофонный зажим 8 Поместите провод микрофона в канавку. • Микрофон может быть установлен без использования микрофонного зажима. В этом случае отсоедините основание микрофона от микрофонного зажима. Чтобы отсоединить основание микрофона от микрофонного зажима, скользите основанием микрофона. 2. Установка микрофонного зажима на рулевой колонке. (Рис. 4) (Рис. 5) 9 Двусторонняя лента a Установите микрофонный зажим на задней стороне рулевой колонки. b Скоба Используйте отдельно продаваемые скобы для крепления проводов внутри автомобиля, где это необходимо. Регулировка угла наклона микрофона (Рис. 6) Угол микрофона может быть отрегулирован. 7. Rear output 8. Front output 32. Power amp (sold separately) 31. To subwoofer output 11. IP-BUS cable 16. Fuse (10 A) 18. Yellow (2*) Connect to the constant 12 V supply terminal. 19. Fuse resister 20. Red (5*) 21. Red (4*) Accessory Connect to terminal controlled by (or back-up) ignition switch (12 V DC). 22. Black (chassis ground) Connect to a clean, paint-free metal location. 23. ISO connector Note In some vehicles, the ISO connector may be divided into two. In this case, be sure to connect to both connectors. 25. Blue/white (7*) Connect to auto-antenna relay control terminal (max. 300 mA 12 V DC). 26. Blue/white (6*) The pin position of the ISO connector will differ depends on the type of vehicle. Connect 6* and 7* when Pin 5 is an antenna control type. In another type of vehicle, never connect 6* and 7*. 27. Speaker leads White: Front left White/black: Front left Gray: Front right Gray/black: Front right Green: Rear left or subwoofer Green/black: Rear left or subwoofer Violet: Rear right or subwoofer Violet/black: Rear right or subwoofer ACC O ACC position 12.Multi-CD player (sold separately) 24. Blue/white Connect to system control terminal of the power amp (max. 300 mA 12 V DC). F 33. System remote control 34. Left 36. Subwoofer 35. Right 36. Subwoofer 37. Front speaker 37. Front speaker 38. Rear speaker 38. Rear speaker 39. Perform these connections when using the optional amplifier. 40. Notes • Change the initial setting of this unit (refer to the operation manual). The subwoofer output of this unit is monaural. • When using a subwoofer of 70 W (2 Ω), be sure to connect with Violet and Violet/black leads of this unit. Do not connect anything with Green and Green/black leads. F O STAR 17. Yellow (3*) Back-up (or accessory) 29. To front output 31. Connect with RCA cables (sold separately) 14. Connect leads of the same color to each other. 15. Cap (1*) Do not remove cap if this terminal is not in use. 32. Power amp (sold separately) N 5. IP-BUS input (Blue) 28. To rear output • When this unit is installed in a vehicle without ACC (accessory) position on the ignition switch, red cable must be wired to the terminal that can detect the operation of the ignition key. Otherwise, battery drain may result. STAR 4. Wired remote input Hard-wired remote control adaptor can be connected (sold separately). 32. Power amp (sold separately) Note N 9. Subwoofer output 4* 3. AUX jack (3.5 φ) Use a stereo mini plug cable to connect with auxiliary device. 41. Microphone OF 10. This product 6. Antenna jack 5* 20 cm 4m OF 2* 1.5 m 15 cm T 3* 1. USB cable Connect to sparately sold USB device. T 13. Note Depending on the kind of vehicle, the function of 3* and 5* may be different. In this case, be sure to connect 2* to 5* and 4* to 3*. 1* Connecting the units 2. Microphone input No ACC position • Use this unit in other than the following conditions could result in fire or malfunction. — Vehicles with a 12-volt battery and negative grounding. — Speakers with 50 W (output value) and 4 ohm to 8 ohm (impedance value). • To prevent short-circuit, overheating or malfunction, be sure to follow the directions below. — Disconnect the negative terminal of the battery before installation. — Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts. — Place all cables away from moving parts, such as gear shift and seat rails. — Place all cables away from hot places, such as near the heater outlet. — Do not pass the yellow cable through a hole into the engine compartment to connect to a battery. — Cover any disconnected cable connectors with insulating tape. — Do not shorten any cables. — Never cut the insulation of the power cable of this unit in order to share the power to other equipment. Current capacity of the cable is limited. — Use a fuse of the rating prescribed. — Never wire the speaker negative cable directly to ground. — Never band together multiple speaker’s negative cables. English • Control signal is output through blue/white cable when this unit is powered on. Connect it to an external power amp’s system remote control or the vehicle’s auto-antenna relay control terminal (max. 300 mA, 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal. • Never connect blue/white cable to external power amp’s power terminal. Also, never connect it to the power terminal of the auto antenna. Otherwise, battery drain or malfunction may result. • IP-BUS connectors are color-coded. Be sure to connect connectors of the same color. • Black cable is ground. This cable and other product’s ground cable (especially, high-current products such as power amp) must be wired separately. Otherwise, fire or malfunction may result if they are accidentally detached. Connecting the units Connection Diagram 1. USB cable Connect to separately sold USB device. 2. Microphone input 3. AUX jack (3.5 ø) Use a stereo mini plug cable to connect with auxiliary device. 4. Wired remote input Hard-wired remote control adaptor can be connected (sold separately). 5. IP-BUS input (Blue) 6. Antenna jack 7. Rear output 8. Front output 9. Subwoofer output 10.This product 11.IP-BUS cable 12.Multi-CD player (sold separately) 13.Note Depending on the kind of vehicle, the function of 3* and 5* may be different. In this case, be sure to connect 2* to 5* and 4* to 3*. 14.Connect leads of the same color to each other. 15.Cap (1*) Do not remove cap if this terminal is not in use. 16.Fuse (10 A) 17.Yellow (3*) Back-up (or accessory) 18.Yellow (2*) Connect to the constant 12 V supply terminal. 19.Fuse resister 20.Red (5*) Accessory (or back-up) 21.Red (4*) Connect to terminal controlled by ignition switch (12 V DC). 22.Black (chassis ground) Connect to a clean, paint-free metal location. 23.ISO connector Note In some vehicles, the ISO connector may be divided into two. In this case, be sure to connect to both connectors. English 24.Blue/white Connect to system control terminal of the power amp (max. 300 mA 12 V DC). 25.Blue/white (7*) Connect to auto-antenna relay control terminal (max. 300 mA 12 V DC). 26.Blue/white (6*) The pin position of the ISO connector will differ depends on the type of vehicle. Connect 6* and 7* when Pin 5 is an antenna control type. In another type of vehicle, never connect 6* and 7*. 27.Speaker leads White: Front left + White/black: Front left * Gray: Front right + Gray/black: Front right * Green: Rear left + or subwoofer + Green/black: Rear left * or subwoofer * Violet: Rear right + or subwoofer + Violet/black: Rear right * or subwoofer * 28.To rear output 29.To front output 30.To subwoofer output 31.Connect with RCA cables (sold separately) 32.Power amp (sold separately) 33.System remote control 34.Left 35.Right 36.Subwoofer 37.Front speaker 38.Rear speaker 39.Perform these connections when using the optional amplifier. 40.Notes • Change the initial setting of this unit (refer to the operation manual). The subwoofer output of this unit is monaural. • When using a subwoofer of 70 W (2 Ω), be sure to connect with Violet and Violet/black leads of this unit. Do not connect anything with Green and Green/black leads. 41.Microphone • Wenn dieses Gerät in einem Auto eingebaut wird, as auf dem Zündschalter keine ACC (Zubehör)Position hat, sollte die rote Leitung des Geräts an eine Klemme angeschlossen werden, die die Position des Zündschalters erfassen kann. Anderenfalls kann die Autobatterie entleert werden. ACC O O STAR ACC-Position F N F STAR 24.Azul/blanco Conecte al terminal de control de sistema del amplificador de potencia (máx. 300 mA 12 V CC). 25.Azul/blanco (7*) Conecte al terminal de control de relé de antena automática (máx. 300 mA 12 V CC). 26.Azul/blanco (6*) La posición de los contactos del conector ISO difiere dependiendo del tipo del vehículo. Conecte 6* y 7* cuando el contacto 5 es del tipo de control de antena. En otros tipos de vehículo, no conecte nunca 6* y 7*. 27.Hilos de altavoz Blanco: Izquierda delantera + Blanco/negro: Izquierda delantera * Gris: Derecha delantera + Gris/negro: Derecha delantera * Verde: Izquierda trasera + o altavoz de subgraves + Verde/negro: Izquierda trasera * o altavoz de subgraves * Violeta: Derecha trasera + o altavoz de subgraves + Violeta/negro: Derecha trasera * o altavoz de subgraves * 28.A la salida trasera 29.A la salida delantera 30. A la salida del altavoz de subgraves 31.Conecte los cables RCA (vendidos separadamente) 32.Amplificador de potencia (vendido separadamente) 33.Control remoto de sistema 34.Izquierda 35.Derecha 36.Altavoz de subgraves 37.Altavoz delantero 38.Altavoz trasero 39.Realice estas conexiones cuando utilice el amplificador opcional. 40.Notas • Cambie el ajuste inicial de esta unidad (refiérase al manual de operación). La salida de altavoz de subgraves de esta unidad es monofónica. • Cuando utilice un altavoz de subgraves de 70 W (2 Ω), asegúrese de conectarlo con los hilos Violeta y Violeta/negro de esta unidad. No conecte nada con los hilos Verde y Verde/negro. 41.Micrófono Hinweise N Sin posición ACC T • El uso de esta unidad en condiciones diferentes de las siguientes podría causar un fuego o fallo de funcionamiento. — Vehículos con una batería de 12 voltios y puesta a tierra negativa. — Altavoz con 50 W (valor de salida) y de 4 a 8 ohmios (valor de impedancia). • Para prevenir cortocircuitos, sobrecalentamiento o fallo de funcionamiento, asegúrese de seguir las instrucciones a continuación. — Desenchufe el terminal negativo de la batería antes de la instalación. — Fije el cableado con abrazaderas de cable o con cinta adhesiva. Para proteger el cableado, envuélvalo con cinta adhesiva donde el cableado se apoya sobre piezas metálicas. — Posicione todos los cables alejados de las piezas móviles, como el cambio de marchas y rieles de los asientos. — Posicione todos los cables alejados de lugares calientes como cerca de la salida del calentador. — No pase el cable amarillo a través de un agujero en el compartimiento del motor para conectar la batería. — Cubra cualquier conector de cable desconectado con cinta de aislamiento. — No acorte ningún cable. — No corte nunca el aislamiento del cable de alimentación de esta unidad para compartir la energía con otro equipo. La capacidad de corriente del cable es limitada. — Utilice un fusible con la capacidad especificada. — No conecte nunca el cable negativo de altavoz directamente a la puesta a tierra. — No junte nunca múltiples cables negativos de altavoz. 1. Cable USB Conecte al dispositivo USB vendido separamente. 2. Entrada de micrófono 3. Jack AUX (3.5 ø) Utilice un cable con clavija mini estéreo con el equipo auxiliar. 4. Entrada remota cableada Se puede conectar el adaptador de control remoto cableado (vendido separadamente). 5. Entrada IP-BUS (Azul) 6. Toma de antena 7. Salida trasera 8. Salida delantera 9. Salida de altavoz de subgraves 10.Este producto 11.Cable IP-BUS 12.Reproductor de Multi-CD (vendido separadamente) 13.Nota Dependiendo del tipo de vehículo, la función de 3* y 5* puede ser diferente. En este caso, asegúrese de conectar 2* a 5* y 4* a 3*. 14.Conecte los hilos del mismo color a cada otro. 15.Tapa (1*) No quite la tapa cuando no se utiliza este terminal. 16.Fusible (10 A) 17.Amarillo (3*) Reserva (o accesorio) 18.Amarillo (2*) Conecte el terminal de suministro de 12 V constante. 19.Resistencia de fusible 20.Rojo (5*) Accesorio (o reserva) 21.Rojo (4*) Conecte al terminal controlado por del interruptor de encendido (12 V CC). 22.Negro (masa de la carrocería) Conecte a un punto de metal limpio, libre de pintura. 23.Conector ISO Nota En algunos vehículos, puede que el conector ISO esté dividido en dos. En este caso, asegúrese de conectar a ambos conectores. Anschließen der Geräte OF O Diagrama de conexión Español OF F STAR STAR Posición ACC OF O T ACC N F N OF • Cuando se instale esta unidad en un vehículo sin la posición ACC (accesorio) en el interruptor de encendido, se debe conectar el cable rojo al terminal que puede detectar la operación de la llave de encendido. De lo contrario, la batería puede descargarse. • La señal de control se emite a través del cable azul/ blanco cuando se enciende esta unidad. Conéctelo a un terminal de control de sistema de amplificador de potencia externo o al terminal de control de relé de antena automática del vehículo (máx. 300 mA, 12 V CC). Si el vehículo está equipado con una antena de vidrio, conéctelo al terminal de suministro de potencia de refuerzo de la antena. • No conecte nunca el cable azul/blanco al terminal de alimentación de un amplificador de potencia externo. Igualmente, no conéctelo nunca al terminal de alimentación de la antena automática. De lo contrario, puede ocurrir la descarga de la batería o un fallo de funcionamiento. • Los conectores IP-BUS están codificados en colores. Asegúrese de conectar los conectores del mismo color. • El cable negro es para la puesta a tierra. Se debe conectar este cable y el cable de puesta a tierra de otro producto (especialmente de productos de alta corriente como un amplificador de potencia) separadamente. De lo contrario, puede ocurrir un fuego o fallo de funcionamiento si los cables se sueltan accidentalmente. Conexión de las unidades T Nota Español T Conexión de las unidades Keine ACC-Position • Wenn das Gerät nicht unter den folgenden Bedingungen eingebaut wird, kann ein Brand oder eine Funktionsstörung auftreten. — Fahrzeuge mit einer 12-Volt-Batterie und negativer Erdung. — Lautsprecher mit 50 W (Ausgangsleistung) und 4 bis 8 Ohm (Impedanz). • Um Kurzschlüsse, eine Überhitzung oder Funktionsstörung zu verhindern, befolgen Sie bitte die folgenden Hinweise: — Trennen Sie die negative Klemme der Batterie vor dem Einbau ab. — Sichern Sie die Leitungen mit Kabelklemmen oder Klebeband. Zum Schutz der Leitungen sollten sie an Stellen, wo sie Metallteile berühren, mit Klebeband umwickelt werden. — Verlegen Sie alle Leitungen so, dass keine beweglichen Teile, wie die Gangschaltung und die Sitzschienen, berühren. — Verlegen Sie alle Kabel so, dass sie von heißen Stellen, wie etwa der Heizungsauslassöffnung entfernt sind. — Führen Sie die gelbe Leitung zum Anschluss an die Batterie nicht durch ein Loch in den Motorraum ein. — Umwickeln Sie abgetrennte Leitungen mit Isolierband. — Verkürzen Sie keine Kabel. — Führen Sie niemals anderen Geräten Strom zu, indem Sie die Isolierung der Stromversorgungsleitung dieses Geräts durchschneiden und davon Strom abzapfen. Die Strombelastbarkeit der Leitung ist begrenzt. — Verwenden Sie eine Sicherung mit dem vorgeschriebenen Nennwert. — Schließen Sie das negative Lautsprecherkabel nie direkt an die Erdung an. — Bündeln Sie nie die negativen Kabeln mehrerer Lautsprecher. • Das Steuersignal wird über das blaue/weiße Kabel ausgegeben, wenn dieses Geräts eingeschaltet wird. Schließen Sie es an eine System-Fernbedienung Deutsch eines externen Leistungsverstärkers oder an die Autoantennenrelais-Steuerungsklemme des Fahrzeugs an (max. 300 mA, 12 V Gleichspannung). Wenn das Fahrzeug mit einer Fensterantenne ausgestattet ist, schließen Sie es an die Antennenverstärker-Stromversorgungsklemme an. • Schließen Sie das blaue/weiße Kabel nie an die Leistungsklemme des Verstärkers an. Außerdem darf das blaue/weiße Kabel nicht an die Leistungsklemme der Auto-Antenne angeschlossen werden. Ein solcher Anschluss könnte zu einer Belastung der Batterie führen und Funktionsstörungen verursachen. • Die IP-BUS-Leitungen sind farbcodiert. Achten Sie immer darauf, Leitungen derselben Farbe miteinander zu verbinden. • Das schwarze Kabel ist das Erdungskabel. Dieses Kabel ist getrennt von der Erde von HochstromGeräten, wie z. B. Leistungsverstärkern, zu erden. Anderenfalls besteht die Gefahr einer Beschädigung der Geräte oder eines Brandes, falls die Erdungsstelle versehentlich abgetrennt wird. Anschließen der Geräte Anschlussdiagramm 1. USB-Kabel Für den Anschluss an das separat erhältliche USB-Gerät. 2. Mikrofoneingang 3. AUX-Buchse (3.5 ø) Zur Verbindung mit Zusatzausrüstung verwenden Sie ein Stereo-Ministeckerkabel. 4. Buchse für die verdrahtete Fernbedienung Hier kann ein Drahtfernbedienungsadapter (getrennt erhältlich) angeschlossen werden. 5. IP-BUS-Eingang (Blau) 6. Antennebuchse 7. Ausgang für hintere Zusatzlautsprecher 8. Ausgang für vorderen Zusatzlautsprecher 9. Subwoofer-Ausgang 10.Dieses Produkt 11.IP-BUS-Kabel 12.Multi-CD-Player (getrennt erhältlich) 13.Hinweis: Je nach Art des Fahrzeugs besitzen 3* und 5* u. U. unterschiedliche Funktionen. Verbinden Sie in einem solchen Fall 2* mit 5* und 4* mit 3*. 14.Verbinden Sie Leitungen derselben Farbe miteinander. 15.Kappe (1*) Wenn dieser Steckverbinder nicht verwendet wird, lassen Sie die Kappe aufgesetzt. 16.Sicherung (10 A) 17.Gelb (3*) Reserve (oder Zubehör) 18.Gelb (2*) An eine Stromversorgung anschließen, die immer Gleichstrom von 12 V führt. 19.Sicherungswiderstand 20.Rot (5*) Zubehör (oder Reserve) 21.Rot (4*) An eine Stromversorgung anschließen, (12 V Gleichspannung), die mit dem Zündschloss ein-/ ausgeschaltet wird. 22.Schwarz (Erdung) An ein sauberes Metallteil anschließen, das von Farbe frei ist. 23.ISO-Anschluss Hinweis: Bei einigen Fahrzeugen kann der ISOSteckverbinder in zwei Hälften geteilt sein. In diesem Fall ist der Anschluss unbedingt an beiden Steckverbindern vorzunehmen. Deutsch 24.Blau/weiß An den Systemsteuerungs-Anschluss des Leistungsverstärkers (max. 300 mA, 12 V Gleichspannung) anschließen. 25.Blau/weiß (7*) An die die Autoantennenrelais-Steuerungsklemme anschließen (max. 300 mA, 12 V Gleichspannung). 26.Blau/weiß (6*) Die Pin-Position des ISO-Anschlusses hängt vom Fahrzeugtyp ab. 6* und 7* anschließen, wenn es sich bei Pin 5 um einen Antennensteuerungstyp handelt. Bei einem anderen Fahrzeugtyp 6* und 7* niemals anschließen. 27.Lautsprecherzuleitungen Weiß: Vorne links + Weiß/Schwarz: Vorne links * Grau: Vorne rechts + Grau/Schwarz: Vorne rechts * Grün: Hinten links + oder Subwoofer + Grün/Schwarz: H  inten links * oder Subwoofer * Violett: Hinten rechts + oder Subwoofer + Violett/Schwarz: Hinten rechts * oder Subwoofer * 28.Zum hinteren Ausgang 29.Zum vorderen Ausgang 30.Zum Subwoofer-Ausgang 31.Mit RCA-Kabeln verbinden (getrennt erhältlich) 32.Leistungsverstärker (getrennt erhältlich) 33.System-Fernbedienung 34.Links 35.Recht 36.Subwoofer 37.Vorderer Lautsprecher 38.Hinterer Lautsprecher 39.Bei Gebrauch des optionalen Verstärkers diese Anschlüsse vornehmen. 40.Hinweise • Ändern Sie die Grundeinstellung dieses Geräts (siehe Bedienungsanleitung). Der Subwoofer-Ausgang dieses Geräts ist Mono. • Bei Verwendung eines Subwoofers von 70 W (2 Ω) achten Sie darauf, den Anschluss an die violetten und violetten/schwarzen Leitungen dieses Geräts herzustellen. Stellen Sie keinen Anschluss mit den grünen und grünen/ schwarzen Leitungen her. 41.Mikrofon • Qualora l’unità venga installata in un veicolo la cui chiavetta di accensione è sprovvista della posizione ACC (accessori), il cavo rosso deve essere collegato al terminale in grado di rilevare il funzionamento della chiavetta stessa. In caso contrario la batteria si scaricherebbe. ACC O O STAR Posizione ACC F N F STAR 24.Bleu/blanc Connectez à la prise de commande du système de l’amplificateur de puissance (max. 300 mA 12 V CC). 25.Bleu/blanc (7*) Connectez à la prise du contrôle de relais de l’antenne automatique (max. 300 mA, 12 V CC). 26.Bleu/blanc (6*) La position des broches du connecteur ISO diffère en fonction du type de véhicule. Connectez 6* et 7* quand la broche 5 correspond à la commande de l’antenne. Dans les autres cas, ne connectez jamais 6* et 7*. 27.Câbles d’enceinte Blanc: Avant gauche + Blanc/noir: Avant gauche * Gris: Avant droit + Gris/noir: Avant droit * Vert: Arrière gauche + ou caisson de grave + Vert/noir: Arrière gauche * ou caisson de grave * Violet: Arrière droit + ou caisson de grave + Violet/noir: Arrière droit * ou caisson de grave * 28.À la sortie arrière 29.À la sortie avant 30.À la sortie du caisson de grave 31.Connectez aux câbles cinch (RCA) (vendus séparément) 32.Amplificateur de puissance (vendu séparément) 33.Télécommande du système 34.Gauche 35.Droit 36.Caisson de grave 37.Enceinte avant 38.Enceinte arrière 39.Réalisez ces connexions lors de l’utilisation de l’amplificateur en option. 40.Remarques • Change le réglage initial de cet appareil (reportez-vous aux mode d’emploi). La sortie de caisson de grave de cet appareil est monophonique. • Lors de l’utilisation d’un caisson de grave de 70 W (2 Ω), assurez-vous de le raccorder aux câbles Violet et Violet/noir de cet appareil. Ne connectez rien aux câbles Vert et Vert/noir. 41.Microphone Nota N Pas de position ACC T • Utiliser cet appareil dans d’autres conditions que les conditions suivantes peut entraîner un incendie ou un mauvais fonctionnement. — Véhicule avec une batterie de 12 volts et une mise à la masse négative. — Enceintes de 50 W (valeur de sortie) et de 4 ohms à 8 ohms (valeur d’impédance). • Pour éviter tout court-circuit, surchauffe ou mauvais fonctionnement, assurez-vous de suivre les instructions ci-dessous. — Déconnectez la borne négative de la batterie avant l’installation. — Fixez solidement les câbles avec des serre-câbles ou du ruban adhésif. Pour protéger le câblage, entourez-le de ruban adhésif à l’endroit où il est en contact avec des pièces métalliques. — Tenez tous les câbles à l’écart des parties mobiles, telles que le levier de vitesse et les rails des sièges. — Tenez tous les câbles à l’écart des endroits chauds, tels que les sorties du chauffage. — Ne faites pas passer le câble jaune par un trou dans le compartiment du moteur pour le connecter à la batterie. — Recouvrez tous les câbles non connectés avec du ruban isolant. — Ne raccourcissez aucun câble. — Ne coupez jamais l’isolant du câble d’alimentation de cet appareil afin partager l’alimentation avec un autre appareil. La capacité électrique du câble est limitée. — Utilisez un fusible de la valeur donnée. — Ne connectez jamais le câble négatif des enceintes directement à la masse. — N’attachez jamais ensemble plusieurs câbles négatifs de plusieurs enceintes. 1. Câble USB Connectez-le à un périphérique USB vendu séparément. 2. Entrée microphone 3. Prise AUX (3.5 ø) Utilisez un câble à fiches stéréo mini pour raccorder un appareil auxiliaire. 4. Entrée de télécommande câblée Un adaptateur de télécommande câblée peut être connecté (vendu séparément). 5. Entrée IP-BUS (Bleu) 6. Prise d’antenne 7. Sortie arrière 8. Sortie avant 9. Sortie du caisson de grave 10.Cet appareil 11.Câble IP-BUS 12.Lecteur de CD à chargeur (vendu séparément) 13.Remarque En fonction du type de véhicule, la fonction de 3* et de 5* peut différer. Sans ce cas, assurezvous de connecter 2* à 5* et 4* à 3*. 14.Connectez les câbles de la même couleur les uns aux autres. 15.Capuchon (1*) Ne retirez pas le capuchon si cette prise n’est pas utilisée. 16.Fusible (10 A) 17.Jaune (3*) Secours (ou accessoire) 18.Jaune (2*) Connectez à une prise d’alimentation constante 12 V. 19.Résistance fusible 20.Rouge (5*) Accessoire (ou secours) 21.Rouge (4*) Connectez à une prise commandée par le commutateur d’allumage (12 V CC). 22.Noire (masse au châssis) Connectez à une section métallique propre et sans peinture. 23.Connecteur ISO Remarque Dans certains véhicule, le connecteur ISO peut être divisé en deux. Dans ce cas, assurez-vous de faire la connexion aux deux connecteurs. Collegamento delle unità OF O Diagramme de connexion Français OF F STAR STAR Position ACC OF O T ACC N F N OF • Si cet appareil est installé dans un véhicule sans position ACC (accessoire) sur le commutateur d’allumage, le câble rouge doit être connecté à une borne qui peut détecter la position du commutateur d’allumage. Sinon, la batterie risque de se décharger. • Le signal de commande est sorti par le câble bleu/ blanc quand cet appareil est sous tension. Connectezle à la télécommande d’un système d’amplification extérieur ou à la prise de commande du contrôle de relais de l’antenne automatique (max. 300 mA, 12 V CC). Si le véhicule est équipée d’une antenne de vitre, connectez-la à la prise d’alimentation de l’amplificateur d’antenne. • Ne connectez jamais le câble bleu/blanc à la prise d’alimentation d’un amplificateur extérieur. Et ne le connectez pas à la prise d’alimentation de l’antenne automatique. Sinon, la batterie risque de se décharger ou un mauvais fonctionnement peut se produire. • Les connecteurs IP-BUS sont codés par couleur. Assurez-vous de connecter les connecteurs de même couleur. • Le câble noir est pour la masse. Ce câble et les câbles de masse des autres produits (en particulier les appareils à haute intensité tels que les amplificateurs) doivent être câblés séparément. Sinon, ils peuvent entraîner un incendie ou un mauvais fonctionnement s’ils se détachent. Connexions des appareils T Remarque Français T Connexions des appareils Assenza di posizione ACC • L’impiego dell’unità in condizioni diverse dalle seguenti potrebbe dar luogo a incendi o malfunzionamenti: — Veicoli provvisti di batteria da 12 V con messa a terra sul negativo. — Altoparlanti da 50 W (uscita) e da 4 ohm a 8 ohm (impedenza). • Per impedire il verificarsi di cortocircuiti, di surriscaldamento o di malfunzionamenti raccomandiamo di osservare le seguenti istruzioni. — Prima di procedere con l’installazione scollegate il terminale negativo della batteria. — Bloccate i cavi con apposite fascette o con del nastro adesivo. Per proteggere i cavi che scorrono contro le parti metalliche del veicolo avvolgeteli inoltre con del nastro adesivo. — Allontanate tutti i cavi da qualsiasi parte in movimento quali, ad esempio, la leva del cambio e le guide dei sedili. — Allontanate tutti i cavi da punti ad elevata temperatura quali, ad esempio, gli effusori del sistema di riscaldamento del veicolo. — Per collegare il cavo giallo alla batteria non fatelo passare per un foro ricavato nella struttura di separazione dal vano del motore. — Proteggete con del nastro adesivo tutti i connettori non usati. — Non accorciate alcun cavo di collegamento. — Non tagliate la guaina d’isolamento del cavo di alimentazione di questa unità in modo da prelevare corrente per alimentare altri apparecchi. La capacità di corrente di questo cavo è infatti limitata. — Usate solo un fusibile della capacità prescritta. — Non collegate mai direttamente a terra il cavo negativo degli altoparlanti. — Non raggruppate fra loro il cavo negativo di più altoparlanti. Italiano • Quando l’unità è accesa il segnale di controllo è posto in uscita attraverso il cavo blu/bianco. Collegatelo al telecomando di un amplificatore di potenza esterno o al terminale di controllo del relé dell’antenna automatica del veicolo (massimo 300 mA e 12 V CC). Se il veicolo è provvisto di un’antenna a vetro collegatela al terminale di alimentazione del relativo booster. • Non collegate il cavo blu/bianco al terminale di alimentazione dell’amplificatore di potenza esterno. Non collegatelo inoltre al terminale di alimentazione dell’antenna. In caso contrario la batteria si scaricherebbe oppure si potrebbero verificare dei malfunzionamenti. • I connettori IP-BUS sono codificati a colore. È pertanto necessario collegarli a connettori dello stesso colore. • Il cavo nero va usato solo per la messa a terra. Questo cavo e il cavo di messa a terra di altri apparecchi (in particolare quelli ad alta corrente quali gli amplificatori di potenza) devono essere collegati separatamente. In caso contrario, qualora si scolleghino accidentalmente, si potrebbero verificare incendi o malfunzionamenti. Collegamento delle unità Schema di collegamento 1. Cavo USB Da collegare a una periferica USB acquistata a parte. 2. Ingresso microfono 3. Presa AUX (3.5 ø) Per il collegamento all’apparecchio ausiliario utilizzate un cavo con spina stereo mini. 4. Ingresso del telecomando a filo Qui si collega l’adattatore del telecomando a filo (venduto a parte). 5. Ingresso IP-BUS (Blu) 6. Presa d’antenna 7. Uscita posteriore 8. Uscita anteriore 9. Uscita del subwoofer 10.Questo apparecchio 11.Cavo IP-BUS 12.Multilettore CD (venduto separatamente) 13.Nota In funzione del tipo di veicolo le funzione di 3* e di 5* potrebbe differire. In tal caso collegare 2* a 5* e 4* a 3*. 14.Collegare fra loro i cavi di uguale colore. 15.Capocorda (1*) Non deve essere rimosso quando non si impiega questo connettore. 16.Fusibile (10 A) 17.Giallo (3*) Retromarcia (o accessorio) 18.Giallo (2*) Da collegare al terminale costantemente alimentato a 12 V. 19.Resistenza fusibile 20.Rosso (5*) Accessorio (o retromarcia) 21.Rosso (4*) Da collegare al terminale controllato dalla chiavetta di accensione (12 V CC). 22.Nero (messa a terra sulla carrozzeria) Da collegare in un punto metallico pulito e non verniciato. 23.Connettore ISO Nota In alcuni veicoli il connettore ISO potrebbe essere separato in due. In tal caso è necessario collegare entrambi. Italiano 24.Blu/bianco Da collegare al terminale di controllo di sistema dell’amplificatore di potenza (massimo 300 mA 12 V CC). 25.Blu/bianco (7*) Da collegare al terminale di controllo del relé dell’antenna automatica (massimo 300 mA 12 V CC). 26.Blu/bianco (6*) La posizione dei contatti del connettore ISO può differire in funzione del tipo di veicolo. Collegare 6* e 7* qualora il contatto 5 sia del tipo per controllo dell’antenna. In altri tipi di veicolo 6* e 7* non devo mai essere collegati. 27.Cavi altoparlanti Bianco: Anteriore sinistro + Bianco/nero: Anteriore sinistro * Grigio: Anteriore destro + Grigio/nero: Anteriore destro * Verde: Posteriore sinistro + o subwoofer + Verde/nero: Posteriore sinistro * o subwoofer * Viola: Posteriore destro + o subwoofer + Viola/nero: Posteriore destro * o subwoofer * 28.All’uscita posteriore 29.All’uscita anteriore 30.All’uscita subwoofer 31.Da collegare ai cavi RCA (venduti a parte) 32.Amplificatore di potenza (venduto a parte) 33.Telecomando del sistema 34.Sinistra 35.Destra 36.Subwoofer 37.Diffusore anteriore 38.Diffusore posteriore 39.Questi collegamenti devono essere eseguiti quando s’impiega l’amplificatore opzionale. 40.Note • Cambiare l’impostazione iniziale di questa unità (far riferimento al manuale d’istruzioni per l’uso). L’uscita subwoofer di questa unità è di tipo mono. • Se s’impiega un subwoofer da 70 W (2 Ω) è necessario collegarlo con i cavi viola e viola/ nero di questa unità. Nulla deve invece essere collegato con i cavi verde e verde/nero. 41.Microfono Примечание • Когда данное устройство устанавливается в транспортном средстве без ACC (вспомогательные приборы) положения на замке зажигания, красный кабель должен быть подключен к клемме, которая может обнаружить работу замка зажигания. Иначе, в результате батарея может разрядиться. ACC O O STAR АСС положение F N F STAR T • Gebruik van dit toestel onder andere dan de volgende omstandigheden kan leiden tot brand of storingen. — Voertuigen met een negatief geaarde 12 V accu. — Luidsprekers van 50 W (uitgangsvermogen) en 4 Ohm tot 8 Ohm (impedantie). • Om kortsluiting, oververhitting of andere storingen te voorkomen moet u de onderstaande instructies opvolgen. — Koppel de negatieve pool van de accu los voor u begint met de installatie. — Zet alle bedrading vast met kabelklemmen of isolatieband. Ter bescherming van de bedrading dient u deze te omwikkelen met isolatieband waar de bedrading met metalen onderdelen in aanraking komt. — Houd alle bedrading uit de buurt van bewegende onderdelen, zoals de versnellingspook en de stoelenrails. — Houd de bedrading uit de buurt van zeer warme plekken, zoals bij een verwarmingsrooster. — Leid de gele draad niet door een gat naar het motorcompartiment om aan te sluiten op de accu. — Plak eventuele losse aansluitingen, draadeinden of stekkers netjes af met isolatieband. — Maak de kabels niet korter. — Tap in geen geval de stroomkabel voor dit toestel af om andere apparatuur van stroom te voorzien. Het vermogen van de draad is beperkt. — Gebruik een zekering met het voorgeschreven vermogen. — Sluit de negatieve luidsprekerdraden in geen geval direct op aarde aan. — Bundel de negatieve luidsprekerdraden in geen geval samen. 24.Blauw/wit Verbinden met de systeembedieningsaansluiting van de eindversterker (max. 300 mA 12 V gelijkstroom). 25.Blauw/wit (7*) Verbinden met de stuuraansluiting van het relais van de antenne van het voertuig (max. 300 mA 12 V gelijkstroom). 26.Blauw/wit (6*) De penposities van de ISO stekker hangen mede af van het type voertuig. Sluit 6* en 7* aan wanneer pen 5 de antenne aanstuurt. In andere typen voertuigen hoeft u 6* en 7* helemaal niet aan te sluiten. 27.Luidsprekerdraden Wit: Links voor + Wit/zwart: Links voor * Grijs: Rechts voor + Grijs/zwart: Rechts voor * Groen: Links achter + of subwoofer + Groen/zwarte: Links achter * of subwoofer * Paars: Rechts achter + of subwoofer + Paars/zwarte: Rechts achter * of subwoofer * 28.Naar de achter-uitgang 29.Naar de voor-uitgang 30.Naar de subwoofer uitgang 31.Aansluiten met RCA (tulpstekker) kabels (los verkrijgbaar) 32.Eindversterker (los verkrijgbaar) 33.Systeemafstandsbediening 34.Links 35.Rechts 36.Subwoofer 37.Voor-luidspreker 38.Achter-luidspreker 39.Voer deze verbindingen uit wanneer u de los verkrijgbare versterker gebruikt. 40.Opmerkingen • Verander de basisinstelling van dit toestel (zie bladzijde de Gebruiksaanwijzing). De subwoofer weergave van dit toestel is in mono. • Bij gebruik van een subwoofer van 70 W (2 Ω), moet u erop letten dat u de aansluiting verricht met de paarse en paars/zwarte draden van dit toestel. Sluit niets aan op de groene en groen/zwarte draden. 41.Microfoon N Geen ACC stand 1. USB kabel Sluit deze aan op een los verkrijgbaar USB apparaat. 2. Microfoon ingangsaansluiting 3. AUX aansluiting (3.5 ø) Gebruik een kabel met een stereo ministekker voor het aansluiten van externe apparatuur. 4. Afstandsbediening met draad Er kan een adapter voor een afstandsbediening met draad worden aangesloten (los verkrijgbaar). 5. IP-BUS ingangsaansluiting (Blauw) 6. Antenne-aansluiting 7. Achter-uitgang 8. Voor-uitgang 9. Subwoofer uitgang 10.Dit product 11.IP-BUS-kabel 12.Multi CD-wisselaar (los verkrijgbaar) 13.Opmerking Afhankelijk van het soort voertuig is het mogelijk dat de functies van 3* en 5* verschillen. Let er in een dergelijk geval op dat u 2* op 5* en 4* op 3* aansluit. 14.Sluit in het algemeen draden van dezelfde kleur op elkaar aan. 15.Dop (1*) Laat het dopje zitten wanneer de aansluiting niet wordt gebruikt. 16.Zekering (10 A) 17.Geel (3*) Back-up (of accessoire) 18.Geel (2*) Verbinden met de continue 12 V stroomaansluiting. 19.Zekering 20.Rood (5*) Accessoire (of back-up) 21.Rood (4*) Verbinden met een elektrische aansluiting die aangestuurd wordt via het contactslot (12 V gelijkstroom). 22.Zwart (chassis aarde) Aansluiten op een schone, blank metalen plek. 23.ISO stekker Opmerking In sommige voertuigen kan de ISO stekker in twee stukken gedeeld zijn. Sluit in een dergelijk geval beide stekkers aan. Подключение устройств OF O Aansluitingsschema Nederlands OF F STAR STAR ACC stand OF O T ACC N F N OF • Wanneer dit toestel geïnstalleerd is in een voertuig zonder ACC (accessoire) stand op het contactslot, moet de rode draad worden verbonden met een aansluiting die de stand van de contactsleutel kan herkennen. Anders kan de accu leeglopen. • Via de blauw/witte draad wordt een stuursignaal geproduceerd wanneer dit toestel is ingeschakeld. Verbind deze met de systeemafstandsbediening van een externe eindversterker, of met de stuuraansluiting voor het relais van de antenne van het voertuig (max. 300 mA, 12 V gelijkstroom). Als het voertuig een ruitantenne heeft, dient u deze draad te verbinden met de stroomaansluiting van de antennesignaalversterker (booster). • Verbind de blauw/witte draad in geen geval met de stroomaansluiting van een externe eindversterker. Verbind deze draad ook in geen geval met de stroomaansluiting zelf van de antenne van de auto. Doet u dit toch, dan kan de accu leeglopen of kunnen zich andere storingen voordoen. • IP-BUS stekkers zijn kleurgecodeerd. Let erop dat u alleen stekkers van dezelfde kleur op elkaar aansluit. • De zwarte draad is de aarding. Deze draad en de aardingen van andere apparatuur (in het bijzonder producten met een hoog vermogen, zoals een eindversterker), moeten onafhankelijk van elkaar worden aangesloten. Doet u dit niet, dan kan er brand ontstaan of kunnen zich storingen voordoen wanneer de bedrading onbedoeld los raakt. Aansluiten van de toestellen T Opmerking Nederlands T Aansluiten van de toestellen АСС положение нет • Использование данного устройства в иных, чем следующие условия, может привести к возгоранию или неправильному срабатыванию. — Автомобиль батареей с 12-вольт и отрицательным заземлением. — Динамики с 50 Вт (выходная величина) и от 4 ОМ до 8 ОМ (полное сопротивление). • Чтобы предотвратить короткое замыкание, перегрев или неправильное срабатывание убедитесь, что следуете указаниям ниже. — Отсоедините отрицательную клемму батареи пред установкой. — Закрепите провода кабельными зажимами или липкой лентой. Для защиты проводов следует обмотать их липкой летной в тех местах, где они соприкасаются с металлическими частями. — Прокладывайте все кабели вдали от двигающихся частей, таких как рычаг переключения коробки передач или направляющая для выдвижения сиденья. — Прокладывайте все кабели вдали от горячих мест, таких как рядом с выпуском нагревателя. — Не пропускайте желтый кабель через отверстие в моторном отсеке, для того чтобы подключить его к батарее. — Защитите все неподключенные кабели разъемами с изоляционной лентой. — Не укорачивайте какие-либо кабели. — Никогда не обрезайте изоляцию питающего кабеля данного устройства, чтобы подключить питание на другое оборудование. Пропускная способность кабеля ограничена. — Используйте плавкий предохранитель заданного номинала. — Никогда не подключайте отрицательный кабель динамика напрямую к заземлению. — Никогда не связывайте вместе различные отрицательные кабели динамиков. Pyccкий • Контрольный сигнал выходит по сине/белому кабелю, когда данное устройство подключено к электропитанию. Подключите его к системе дистанционного управления внешнего усилителя мощности или к клемме управляющего реле автомобильной антенны (макс. 300 мА, 12 В пост. ток). Если автомобиль снабжен стеклянной антенной, подключите её к питающему терминалу антенного усилителя. • Никогда не подключайте сине/белый кабель к питающему терминалу внешнего усилителя мощности. Так же, никогда не подключайте его к питающему терминалу автомобильной антенны. Иначе, в результате батарея разрядится или будет происходить неправильное срабатывание. • IP-BUS соединители с цветовым кодированием. Будьте уверены, что соединяете соединители одинакового цвета среди соединителей с цветовым кодированием. • Черный кабель – заземление. Этот кабель и кабели заземления других изделий (особенно, сильноточные изделия, такие как усилитель мощности) должны быть проложены раздельно. Иначе, в результате может произойти возгорание или неправильное срабатывание, если они внезапно отсоединятся. Подключение устройств Схема Соединений 1. USB кабель Подключить к отдельно продающемуся устройству USB. 2. Вход микрофона 3. Гнездо AUX (3.5 φ) Используйте стереокабель с мини-штекером для подключения вспомогательной аппаратуры. 4. Дистанционный монтажный вход Адаптер жестко смонтированного дистанционного управления может быть подключен (продается отдельно). 5. Разъем для подключения IP-BUS (голубой) 6. Гнездо антенны 7. Задний выход 8. Передний выход 9. Выход низкочастотного динамика 10. Данное устройство 11. Кабель IP-BUS 12. Многодисковый проигрыватель (продается отдельно) 13. Примечание В зависимости от типа автомобиля функции 3* и 5* могут быть различными. В этом случае, убедитесь, что 2* подключили к 5* и 4* к 3*. 14. Соедините провода одинакового цвета друг с другом. 15. Колпачок (1*) Не снимайте колпачок, если клемма не используется. 16. Плавкий предохранитель (10 A) 17. Желтый (3*) Разрывный (или вспомогательный) 18. Желтый (2*) Подключите к клемме постоянно подающей 12 В. 19. Резистор предохранителя 20. Красный (5*) Вспомогательный (или разрывный) 21. Красный (4*) Подключите к клемме, контролируемой замком зажигания (12 В пост. ток). 22. Черный (заземление на массу) Подключите к чистому, неокрашенному металлическому участку. 23. ISO разъем Примечание В некоторых автомобилях ISO разъем может быть разделен на два. В этом случае убедитесь, что подключили оба разъема. Pyccкий 24. Синий/белый Подключите к клемме системы контроля усилителя мощности (макс. 300 мА 12 В пост. ток). 25. Синий/белый (7*) Подключите к клемме управления реле автомобильной антенны (макс. 300 мА 12 В пост. ток). 26. Синий/белый (6*) Расположение штырей ISO разъема может быть различным в зависимости от типа автомобиля. Соедините 6* и 7* когда штырь 5 это штырь типа управления антенны. В других типах автомобилей никогда не соединяйте 6* и 7*. 27. Провода динамиков Белый: Передний левый + Белый/черный: Передний левый * Серый: Передний правый + Серый/черный: Передний правый * Зеленый: Задний левый + или низкочастотный динамик + Зеленый/черный: Задний левый * или низкочастотный динамик * Фиолетовый: Задний правый + или низкочастотный динамик + Фиолетовый/черный: Задний правый * или низкочастотный динамик * 28. К заднему выходу 29. К переднему выходу 30. К заднему выходу низкочастотного динамика 31. Соедините с кабелями RCA (продаются отдельно) 32. Усилитель мощности (продается отдельно) 33. Система дистанционного управления 34. Левый 35. Правый 36. Низкочастотный динамик 37. Передний динамик 38. Задний динамик 39. Выполните данные подключения, когда используется усилитель, который не входит в состав обязательного оборудования. 40. Примечание • Измените исходные настройки данного устройства (См. Руководство по эксплуатации). Низкочастотный динамик данного устройства обеспечивает монофонический выходной сигнал. • Когда используется Низкочастотный динамик 70 Вт (2 Ω), будьте уверены, что соединили Фиолетовый провод с Фиолетово/Черным проводом данного устройства. Ничего не соединяйте с Зеленым проводом и Зелено/Черным проводом. 41. Микрофон
1 / 1

Pioneer DEH-P7100BT Guía de instalación

Categoría
Micrófonos
Tipo
Guía de instalación