Yamaha CC-50 Manual de usuario

Categoría
Reproductores de CD
Tipo
Manual de usuario
Active Servo
Technology
CC-50
Natural Sound Mini Component System
Chaîne Mini de la série “Natural Sound”
Natural Sound Mini Komponenten-System
Natural Sound Mini Komponent System
Sistema di Componenti Mini a Suono Naturale
Sistema de Componentes con Sonido Natural
Natural Sound Mini Component Systeem
OWNER‘S MANUAL
MODE D‘EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
CC-50: RX-S50 + CDX-S50 + KXW-S70 + NX-S50
Remote control transmitter
Télécommande
Fernbedienung
Fjärrkontroll
Telecomando
Controlador remoto
Afstandbediening
Batteries (size AA, UM/SUM-3, R6, HP-7)
Piles (format AA, UM/SUM-3, R6, HP-7)
Batterien (Größe AA, UM/SUM-3, R6, HP-7)
Batterier (Storl. AA, UM/SUM-3, R6, HP-7)
Batterie (dimensioni AA, o UM/SUM-3, o R6, o HP-7)
Pilas (tamaño AA, tipo UM/SUM-3, R6, HP-7)
Batterijen (maat AA, UM/SUM-3, R6, HP-7)
AM (MW/LW) loop antenna
Cadre-antenne AM (PO/GO)
MW/LW-Rahmenantenne
MV/LV ramantenn
Antenna ad anello per AM (MW e LW)
Antena de cuadro AM (OM/OL)
AM (MW/LW) lusantenne
Indoor FM antenna
Antenne intérieure FM
UKW-Innenantenne
FM inomhusantenn
Antenna FM per interni
Antena interior de FM
FM binnenantenne
Speaker cords
Câbles d’enceintes
Lautsprecheranschlußkabel
Högtalarledningar
Cavi per gli altoparlanti
Cables de los altavoces
Luidsprekerdraden
SUPPLIED ACCESSORIES
After unpacking, check that the following parts are contained.
ACCESSOIRES FOURNIS
Après le déballage, vérifier que les pièces suivantes sont incluses.
MITGELIEFERTES ZUBEHÖR
Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind.
MEDFÖLJANDE TILLBEHÖR
Kontrollera efter det apparaten packats upp att följande delar finns med.
ACCESSORI IN DOTAZIONE
Verificare che tutte le parti seguenti siano contenute nell’imballaggio dell’apparecchio.
ACCESORIOS INCLUIDOS
Desembale el aparato y verificar que los siguientes accesorios están en la caja.
BIJGELEVERDE ACCESSOIRES
Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.
This product complies with the radio frequency interference requirements of the Council Directive 82/499/EEC and/or
87/308/EEC.
Cet appareil est conforme aux prescriptions de la directive communautaire 87/308/CEE.
Diese Geräte entsprechen der EG-Richtlinie 82/499/EWG und/oder 87/308/EWG.
Dette apparat overholder det gaeldende EF-direktiv vedrørende radiostøj.
Questo apparecchio è conforme al D.M.13 aprile 1989 (Direttiva CEE/87/308) sulla soppressione dei radiodisturbi.
Este producto está de acuerdo con los requisitos sobre interferencias de radio frequencia fijados por el Consejo Directivo
87/308 CEE.
Dit product voldoet aan de EEG normen betreffende radio-frekwentie storingen 82/499/EEG en/of 87/308/EEG.
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
INTRODUCTION
CONTENTS
E-1
English
ENGLISH
Page
PRECAUTIONS..................................................................2-3
ACTIVE SERVO TECHNOLOGY ..........................................3
NAMES OF CONTROLS, INDICATORS AND
REAR PANEL PARTS........................................................4-6
REMOTE CONTROL TRANSMITTER................................7-9
PREPARATION FOR USE .............................................10-11
OPEN/CLOSE THE CONTROL DOOR ...............................12
TURNING THE POWER ON/OFF TO THIS SYSTEM.........12
SETTING THE CLOCK........................................................13
SOUND CONTROL..............................................................14
Page
DIGITAL SOUND FIELD PROCESSOR (DSP)
CONTROL............................................................................14
COMPACT DISC PLAYER OPERATION.......................15-22
TUNING OPERATION ....................................................23-25
TAPE DECK OPERATION ............................................26-29
RECORDING A COMPACT DISC..................................30-35
OTHER RECORDINGS...................................................36-37
HOW TO USE THE BUILT-IN TIMER.............................38-41
USING EXTERNAL UNITS.............................................42-43
MAINTENANCE...................................................................43
SPECIFICATIONS................................................................44
TROUBLESHOOTING.........................................................45
Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment. For the best
performance, read this manual carefully. It will guide you in operating your YAMAHA product.
FEATURES
35W + 35W (6) RMS Output Power, 0.08% THD,
50–20,000 Hz
4-Mode Digital Sound Field Processor (DSP)
Digital Sound Field Effective Even by Listening
with Headphones
Random Access Programmable CD Playback
Single Track/Entire Disc Repeat Play
Random-sequence Play
Automatic Synchronized Recording with CD
Playback
Automatic CD Editing Function for Recording to
Tape
Double Cassette Tape Deck with Automatic
Reversing Function
2-Way Speed Dubbing
Dolby B/C Noise Reduction System
40 Station Automatic Preset Tuning
Multi-Use Timer/Sleep Timer
Active Servo Processing Speaker System
(NX-S50)
Remote Control Capability
NOTE
Please check the copyright laws in your country to record from
records, compact discs, radio, etc. Recording of copyright material
may infringe copyright laws.
IMPORTANT
Please record the serial number of this unit in the space below.
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION (FOR CANADA MODEL)
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT AND FULLY INSERT.
FOR CANADIAN CUSTOMER
THIS DIGITAL APPARATUS DOES NOT EXCEED THE “CLASS
B” LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS SET OUT IN THE RADIO INTERFERENCE
REGULATION OF THE CANADIAN DEPARTMENT OF
COMMUNICATION.
E-2
PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT
CD pickup
Leave the power on with no disc in the unit until normal
playback is possible (about 1 hour).
Tape head
Leave the power on with no cassette in the unit until normal
playback is possible (about 1 hour).
Note
If condensation forms on the tape head, foreign matter may
accumulate during use.
Remote control
Wipe off condensation on the transmitter window with a soft
cloth before operating the unit.
CAUTION FOR CARRYING THE CD PLAYER
Be sure not to carry or tip the CD player with discs remaining in it.
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
This system is equipped with the newly developed Active Servo
Processing Speaker System. It is not designed for use with
conventional speakers. Therefore, do not attempt to connect
other speakers than the provided speaker system.
Choose the installation location of this unit carefully. Avoid
placing it in direct sunlight or close to a source of heat. Also avoid
locations subject to vibration and excessive dust, heat, cold or
moisture. Keep it away from sources of hum such as
transformers and electric motors.
Do not operate this unit upside-down. It may overheat, possibly
causing damage.
Never open the cabinet. If something drops into the set, contact
your dealer.
The openings on the cabinet assure proper ventilation of the unit.
If these openings are obstructed, the temperature inside the
cabinet will rise rapidly and eventually damage the circuits.
Therefore, avoid placing objects against these openings and do
not install the unit where the flow of air through the ventilation
openings could be impeded.
Always set the VOLUME control to “0” before starting the audio
source play: increase the volume gradually to an appropriate
level after the play has been started.
When not planning to use this unit for long periods of time (ie.,
vacation, etc.), disconnect the AC power plug from the wall outlet.
Grounding or polarization – Precautions should be taken so that
the grounding or polarization of an appliance is not defeated.
Do not use force on switches, controls or connection wires. When
moving the unit, first disconnect the power plug and the wires
connected to other equipment. Never pull the wire itself.
Do not attempt to clean the unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
Be sure to read the “TROUBLESHOOTING” section regarding
common operating errors before concluding that the unit is faulty.
To prevent lightning damage, disconnect the AC power plug and
the antenna cable when there is an electrical storm.
Do not plug the AC power plug to the wall socket before you
finish all connections.
Never allow metallic items (e.g. screwdrivers, tools, etc.) to come
near the cassette deck’s record/playback head assembly in this
unit. Doing so may not only scratch or damage the head’s mirror-
smooth finish, it may change the magnetic characteristics of the
heads, causing a deterioration in reproduction performance
quality.
Although the cassette deck’s record/playback heads used in this
unit are high quality heads with outstanding reproduction
characteristics, they can become dirty through the use of old
tapes or from dust accumulation over time. This can have a
serious effect on reproduction quality. Clean the heads regularly
with one of the commonly available head cleaners or with
cleaning solutions.
The voltage to be used must be the same as that specified on
this unit. Using this product with a higher voltage than that which
is specified is dangerous and may result in a fire or other type of
accident causing damage. YAMAHA will not be held responsible
for any damage resulting from use of this unit with a voltage other
than that which is specified.
The sound level at a given volume setting depends on a
combination of speaker efficiency, location and many other
factors. Care should be taken to avoid exposure to sudden high
levels of sound, which may occur when turning on the unit with
the volume control setting at high, and to continuous high levels
of sound.
Sudden temperature changes and storage or operation in an
extremely humid environment may cause condensation inside the
cabinet.
Condensation can cause the unit to malfunction.
Follow the procedure below to eliminate condensation.
For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous if
engaged in a live socket outlet.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
IMPORTANT:
The wire in the mains lead are coloured in accordance
with the following code:
Blue: NEUTRAL
Brown: LIVE
The colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug. Proceed
as follows: the wire which is coloured BLUE must be
connected to the terminal which is marked with the letter
N or coloured BLACK. The wire which is coloured
BROWN must be connected to the terminal which is
marked with the letter L or coloured RED. Making sure
that neither core is connected to the earth terminal of the
three pin plug.
ACTIVE SERVO TECHNOLOGY
Active Servo
Processing
Amplifier
Port
Cabinet
High-
amplitude
bass
sound
Signals of low amplitude
Negative-impedance
output drive
Air woofer
(Helmholtz resonator)
Signals
E-3
English
The theory of the Active Servo Technology is based upon two
major factors, the Helmholtz resonator and negative-
impedance drive. Active Servo Processing speakers
reproduce the bass frequencies through an “air woofer”,
which is a small port or opening in the speaker’s cabinet.
This opening is used instead of, and performs the functions
of, a woofer in a conventionally designed speaker system.
Thus, signals of low amplitude within the cabinet can,
according to the Helmholtz resonance theory, be output from
this opening as waves of great amplitude if the design is such
that the size of the opening and the volume of the cabinet are
in the correct proportion to satisfy a certain ratio.
In order to accomplish this, moreover, the amplitudes within
the cabinet must be both precise and of sufficient power
because these amplitudes must overcome the “load”
presented by the air that exists within the cabinet.
Thus it is this problem that is resolved through the
employment of a design in which the amplifier functions to
supply the signals. If the electrical resistance of the voice coil
is reduced to zero, the movement of the speaker unit would
become linear with respect to signal voltage, and, to
accomplish this, a special negative-impedance output-drive
amplifier for subtracting output impedance of the amplifier is
used.
By employing negative-impedance drive circuits, the amplifier
is able to generate precise, low-amplitude low-frequency
waves with superior damping characteristics, and these
waves are then radiated from the cabinet opening as high-
amplitude signals. The system can, therefore, by employing
the negative-impedance output drive amplifier and a speaker
cabinet with the Helmholtz resonator, reproduce an extremely
wide range of frequencies with amazing sound quality and
less distortion.
The features described above are combined to be the
fundamental structure of the Active Servo Technology.
CAUTION 1
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
CAUTION 2
As the laser beam used in this compact disc player is harmful to
the eyes, do not attempt to disassemble the cabinet. Refer
servicing to qualified personnel only.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT
WARNING
To reduce the risk of fire or electric shock, do not expose this unit to
rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
This compact disc player is
classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT
label is located on the rear exterior.
(Europe and U.K. model only)
Laser Diode Properties
Material: GaAlAs
Wavelength: 780nm
Emission Duration: continuous
Laser Output: max. 44.6µW*
* This output is the value measured at a distance of about 200mm
from the objective lens surface on the Optical Pick-up Block.
CLASS 1 LASER PRODUCT
APPAREIL À LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
NAMES OF CONTROLS, INDICATORS AND REAR PANEL PARTS
E-4
CD Player (CDX-S50)
1. Disc Table
2. RESUME button
3. OPEN/CLOSE Button:
4. RANDOM Play Button
5. SKIP Buttons: /
(SEARCH Buttons: / )
6. Stop Button:
7. Play/Pause Button: /
8. Track Number Indicator
9. Time Display
10. (S, F) REPEAT Indicator
11. RANDOM Play Indicator
12. PROGRAM Indicator
13. Music Calendar Indicator
14. Music Calendar OVER Indicator
15. Tape Side Indicator
16. EDIT Indicator
17. Play Indicator:
Receiver (RX-S50)
18. Effect Level Indicator
19. Phones Mode Indicator
20. Preset Number Indicator
21. Band Indicator
22. Station Frequency Indicator
23. DSP ON/OFF Indicator
24. DSP Mode Indicators
25. MEMORY Indicator
26. AUTO TUNING Indicator
27. STEREO Indicator
28. TIMER Set Indicator
29. SLEEP Indicator
30. POWER Switch
31. DSP ON/OFF Selector Button
32. Remote Control Sensor
33. DSP MODE Selector Button
34. SP/PHONES Mode Selector Button
35. INPUT Selector Buttons: /
36. VOLUME Control
37. PHONES Jack
38. DISPLAY Button
39. TUNER PRESET DOWN/UP Buttons
40. A/B/C/D/E (TIMER) Button
41. MEMORY (TIME ADJUST) Button
42. TUNING DOWN (HOUR) Button
43. TUNING UP (MINUTE) Button
44. AUTO/MAN’L (SEC) Button
45. BAND Selector Button
46. AUTO MEMORY (TIMER REC) Button
47. BASS Tone Control
48. TREBLE Tone Control
49. BALANCE Control
30 32 35 36
37
38
39
40
41
42
43
44
45
46
47
48
49
31 33 34
STEREO
AUTO TUNING
PRESET
MHz
MEMORY
SLEEP
TIMER
HALL
DISCO
CHURCH
JAZZ CLUB
DSP
ON OFF
OVER
AB
TRACK TOTAL REMAIN
RANDOM
PROG
EDIT
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
SF
REP
HALL
DISCO
CHURCH
JAZZ CLUB
1 20
DSP
ON OFF
8 9 10 11 12
13 16 171514
18 19 18 20 22
28 292726252423
21
For CD Player
For Receiver
1
45
2 3
6 7
E-5
English
NAMES OF CONTROLS, INDICATORS AND REAR PANEL PARTS
Double Cassette Tape Deck (KXW-S70)
50. DECK A Cassette Compartment
51. DECK A Select Button and Indicator
52. DECK B Select Button and Indicator
53. DECK B Cassette Compartment
54. Stop Button:
55. Play Direction Indicator ( )
56. DECK A EJECT Button
57. Fast Wind Button:
58. Play Button:
59. Reverse Mode Switch
60. DUBBING (NORMAL/HIGH) Buttons and
Indicators
61. REC/PAUSE Button and Indicator
62. Dolby NR Switch
63. Play Button:
64. Fast Wind Button:
65. DECK B EJECT Button
66. Play Direction Indicator ( )
67. PLAY Indicator
Speakers (NX-S50)
68. YST Port
69. Speaker Terminals
50 51 52 53
54
55
56
57
58
59
60 61
62
63
64
65
66
67
68
69
E-6
NAMES OF CONTROLS, INDICATORS AND REAR PANEL PARTS
FREQUENCY STEP switch (General model only)
Because the interstation frequency spacing differs in
different areas, set the FREQUENCY STEP switch
(located at the rear) according to the frequency spacing in
your area. Before setting this switch, disconnect the AC
supply lead of this unit from the AC outlet.
Rear Panel of Receiver
1. Antenna Terminals
2. INPUT (PHONO and AUX) Terminals
3. GND Terminal
4. SPEAKERS Terminals
5. VOLTAGE SELECTOR (General model only)
6. FREQUENCY STEP Switch (General model only)
7. System Control Sockets
8. AC Supply Lead
VOLTAGE SELECTOR (General model only)
The voltage selector on the rear panel of this unit must
be set for your local main voltage BEFORE plugging
into the AC main supply.
Voltages are 110/120/220/240V AC, 50/60 Hz.
Rear Panel of Cassette Tape Deck
9. System Control Connector
Rear Panel of CD Player
10. System Control Connector
10
9
12 34 5
67 8
Names of control buttons
Receiver Control Buttons
1. Remote Control Transmitter Window
2. Preset Station Number Buttons
3. A, B, C, D, E Selector Buttons
4. PRESET DOWN/UP Buttons
5. A/B/C/D/E Button
6. EFFECT LEVEL Down ()/Up (+) Buttons
7. POWER Switch
8. SLEEP Button
9. DISPLAY Button
10. DSP On/Off Button
11. VOLUME Down ()/Up (+) Buttons
12. DSP MODE Selector Button
13. SP/PHONES Mode Selector Button
14. Input Selector Buttons
E-7
English
REMOTE CONTROL TRANSMITTER
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
1
2
3
4
5
6
7
8 9 10 11
14
13
12
CD Player Control Buttons
15. Track Number Input Buttons
16. TIME Button
17. SKIP Buttons: /
(SEARCH Buttons: / )
18. REPEAT Button
19. RANDOM Button
20. STOP Button:
21. PLAY/PAUSE Button:
22. EDIT Button
23. TAPE Button
24. PROGRAM Button
Tape Deck Control Buttons
25. Play Button:
26. Stop Button:
27. Play Button:
28. DECK A/B Select Button
29. Fast Wind Button:
30. REC/PAUSE Button:
31. Fast Wind Button:
E-8
REMOTE CONTROL TRANSMITTER
-
+
RANDOM
TAPE
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
A/B
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
28
29
25 26 27
31
30
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
15
16
17
18
19
24
20
23
22
21
E-9
English
30°
30°
Remote control
sensor
0.2 m – 6 m
(8” – 20’)
Loading the batteries for the
remote control transmitter
1 Remove the battery compartment cover.
(Press the left edge of the cover to right with a finger, and
then pull it upward.)
2 Insert 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or
equivalent) into the battery compartment.
* Installing the batteries improperly may cause failure.
3 Replace the battery compartment cover.
Precautions for battery use
Insert the batteries according to the direction indicated in
the battery compartment.
Replace all batteries with new ones at the same time.
Remove the batteries if they are weak or if the unit is not
in use for long periods.
Don’t mix normal batteries with rechargeable batteries.
Proper use of the remote control
transmitter
Aim (within the range of 60° with no obstacles) the remote
control transmitter at the remote control sensor and operate
as shown.
Notes concerning use
Replace the batteries if control distance decreases or
operation becomes unstable.
Periodically clean the transmitter window on the remote
control transmitter and the sensor on the main unit with a
soft cloth.
Exposing the sensor on the main unit to strong light
(especially an inverter type of fluorescent lamp etc.) may
interfere with operation. In this case, reposition the main
unit to avoid direct lighting.
Keep the remote control transmitter away from moisture,
excessive heat, shock and vibrations.
The remote control transmitter’s usable range is within
0.2m (8”) and 6m (20’) away from the sensor.
REMOTE CONTROL TRANSMITTER
2
3
1
E-10
Placing the system
This system can be placed any way you like, however, be
sure not to place another unit or any object on top of the
receiver to prevent the ventilation holes on the top panel of
the receiver from being obstructed. If doing so, it may
damage the receiver.
Notes
If the system is put in a rack, allow a space of at least 5
cm (1-15/16”) above and behind the unit.
Disconnect the AC supply lead from the AC outlet before
connecting or disconnecting any component.
Antenna connection
(1) Supplied FM antenna
Connect the FM antenna wire to the corresponding terminal
and direct the FM antenna wire to the direction where the
strongest signal can be received.
(2) Supplied AM (MW/LW) loop antenna
Connect the AM (MW/LW) loop antenna wire to the
corresponding terminals. Position the AM (MW/LW) loop
antenna for optimum reception. Place the AM (MW/LW) loop
antenna on a shelf etc., or install it on the rack or wall with
screws (not supplied).
Notes
When static is still heard even after adjusting the position
of the AM (MW/LW) loop antenna, try reversing the
connection (top to bottom).
Do not place the AM (MW/LW) loop antenna on the unit. It
will result in noise generation, since the unit is equipped
with digital electronics. Place the AM (MW/LW) loop
antenna away from the unit.
(3) External FM antenna
Use an external FM antenna instead of an indoor FM
antenna if you need better reception. Consult your dealer.
(4) External AM (MW/LW) antenna
Use an external AM (MW/LW) antenna if you need better
reception. Consult your dealer.
Note
When using an external AM (MW/LW) antenna, be sure to
keep the wire of the AM (MW/LW) loop antenna connected.
PREPARATION FOR USE
* For U.K. and Europe models, “AM” is replaced by “MW
LW”.
Placing examples
(1
(2
(3
(4
E-11
English
Speaker connection
Connect each speaker wire to the SPEAKERS terminals.
Cautions
Do not let the bare speaker wires touch each other as this
could damage the receiver and/or speakers.
When connecting the speakers to the unit, be sure to
connect the speaker wires properly. Do not mistake the
right channel for the left channel and the plus (+) terminal
for the minus (–) terminal.
Do not connect these SPEAKERS terminals to speakers
other than the provided speaker system NX-S50.
System connection
Connect the red connector on the rear of CDX-S50 to the
red socket on the rear of RX-S50.
Connect the black connector on the rear of KXW-S70 to
the black socket.
How to disconnect the system connector
Grasp both sides of the connector to disconnect the
connector.
Connecting the AC supply lead
After connecting the speakers and system connectors,
plug the AC supply lead into a convenient AC outlet.
Unplug the AC supply lead from the AC outlet if the unit is
not to be used for a long period of time.
PREPARATION FOR USE
R L
(Black wire with white line plus (+) terminal,
black wire minus (–) terminal)
To an
AC outlet
RX-S50
CDX-S50
KXW-S70
OPEN/CLOSE THE CONTROL DOOR
When it is not necessary to operate controls inside the
control door, close the door.
To open or close the door, press the right edge until it clicks.
E-12
STANDBY mode
While the power is on, pressing the POWER switch (or the
POWER switch on the remote control transmitter) switches
the system to the STANDBY mode. (In this mode, the
display shows only the time.) In this mode, main voltage is
still present inside the system. If you want to switch off the
system completely, disconnect the AC power plug from the
AC outlet.
TURNING THE POWER ON/OFF TO THIS SYSTEM
If the AC supply lead is connected to the AC outlet, this
system can be turned ON and OFF (STANDBY mode) by
pressing the POWER switch on the front panel of the
receiver or the POWER button on the remote control
transmitter.
-
+
RANDOM
TAPE
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
A/B
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
E-13
English
1 While the power is on, press the DISPLAY button to
display the time. If the power is off, you can proceed to the
next step.
2 While pressing the TIME ADJUST button, press the
HOUR button and set the hour.
* Press the HOUR button once to advance the time by 1
hour. Press and hold to advance continuously.
3 While pressing the TIME ADJUST button, press the
MINUTE button and set the desired time.
* Press the MINUTE button once to advance the time by
1 minute. Press and hold to advance continuously.
* The hour setting will not advance even if the minute
advance from “59” to “00”.
To display the time by “second”
While pressing the SEC button, the current time is displayed
by minute and second.
To reset the second to “00”
While pressing the SEC button, press the TIME ADJUST
button.
* If the current second is lower than 30, it is reset to 00.
* If the current second is higher than 30, the minute is
advanced by 1 minute and the second is reset to 00.
(If the current minute is “59”, in this case, the hour is also
advanced by 1 hour.)
In the event of a power failure or when the AC supply
lead is disconnected.
The time display will go out, however, the clock will function
for about 30 minutes without power supply. So you do not
have to reset the time if the AC power supply is resumed
within about 30 minutes.
When the AC power supply is resumed after more than 30
minutes pass without power supply, the time display will flash
on and off to indicate that the time must be reset.
Note
If this system is left for several minutes without setting the
time after the AC power lead of this system is connected to
the AC outlet, there may be a case that the display is turned
into a demonstration mode. (This mode is virtually
unnecessary for using this system.)
In this case, first turn the power on by pressing the POWER
switch to cancel the mode, and then set the time.
DISPLAY
MEMORY
TIME ADJ
DOWN UP
TUNING
HOUR MINUTE
MEMORY
TIME ADJ
DOWN UP
TUNING
HOUR MINUTE
SETTING THE CLOCK
Changes.
Changes.
1
2
3
The Digital Sound Field Processor (DSP) built into this unit
presents you with the ambience of an actual concert hall,
jazz club, etc. by adding effects as sonic reflections or
reberverations that create the sound environment of a hall
etc.
This unit provides the following 4 DSP modes that simulates
actual sound environments.
E-14
DIGITAL SOUND FIELD PROCESSOR (DSP) CONTROL
SOUND CONTROL
Volume
Front panel operation
Rotate the VOLUME control towards 10 to increase the
volume, and towards 0 to decrease the volume.
Remote control operation
Press the VOLUME + button to increase the volume and the
VOLUME – button to decrease the volume.
Balance
Adjust the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused from
the speaker settings or the listening room condition.
Turn this clockwise to emphasize the right and
counterclockwise for the left.
Tone
BASS : Turn this clockwise to increase (or counter-
clockwise to decrease) the low frequency
response.
TREBLE : Turn this clockwise to increase (or counter-
clockwise to decrease) the high frequency
response.
BASS TREBLE
–+–+
Mode
HALL
DISCO
CHURCH
JAZZ CLUB
Feature
This mode is suitable for reproducing live
recordings of pop or rock music including
vocals.
You can obtain sound expansion and
reverberations of a hall by this mode.
You can enjoy an atmosphere of disco with
lively bass and powerful sound field.
This mode creates a rich sound field of
church with long reverberations.
It is suitable for vocals etc.
This mode creates a sound field with much
presence adding spatial effect as if music
instruments are coming in front.
E-15
English
COMPACT DISC PLAYER OPERATION
DIGITAL SOUND FIELD PROCESSOR (DSP) CONTROL
Care of compact discs
Compact discs are fairly resistant to damage, however
mistracking can occur due to an accumulation of dirt on the
disc surface.
Follow the guidelines below for maximum enjoyment from
your CD collection and player.
Do not write on either side of the disc, particularly the non-
label side. Signals are read from the non-label side. Do
not mark this surface.
Keep your discs away from direct sunlight, heat and
excessive moisture.
Always hold the CDs by the edges. Fingerprints, dirt or
water on the CDs can cause noise or mistracking. If a CD
is dirty or does not play properly, clean it with a soft, dry
cloth, wiping straight out from the center, along the radius.
Listening to the music with the
DSP
1 Press the DSP ON/OFF switch so that “ON DSP”
illuminates on the display.
2 Select a desired DSP mode by pressing the DSP MODE
selector button once or more until the name of the mode
appears on the display.
3 Playback a source. (For source playback, refer to other
sections described later.)
4 Adjust the level of effects by pressing the EFFECT LEVEL
down (–) or up (+) button.
* Effect level can be checked with the effect level indicator
on the display.
If you will not use the DSP
Press the DSP ON/OFF switch so that “DSP OFF”
illuminates on the display.
When listening with headphones
Press the SP/PHONES mode button so that the phones
mode indicator is illuminated on the display.
You can obtain a DSP effect suitadle for the headphone
listening.
If not using headphones, the SP/PHONES mode button
should be set so that the phones mode indicator is not
illuminated on the display.
Note
DSP effect is also recorded along with a source. If you wish
to record a source without DSP effect, turn the DSP off when
recording.
Receiver
HALL
DSP
ON
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
12
4
2
1
Phones mode indicator
Receiver
E-16
CD playback
1 Select the CD player so that “CD” appears on the display
by pressing the INPUT selector or button.
2 Press the OPEN/CLOSE button to open the disc table.
3 Place a disc on the table, label side up.
* 8 cm (3”) disc can be played without an adaptor.
4 Press the OPEN/CLOSE button to close the disc table.
* The total number of tracks and the total playing time of
the disc will be displayed for several seconds.
* The music calendar will be displayed only for the
number of tracks on the disc.
* If the compact disc contains more than 21 tracks, the
“OVER” indicator will light up on the music calendar.
5 Press the play/pause button to start playback from track 1.
* The “ ” indicator will appear and playback will begin.
As the playback of each track on the music calendar is
finished, that track number will go out.
To interrupt playback
11 Press the play/pause button.
* The “ ” indicator will flash.
22 Press the play/pause button to resume playback from the
same point.
To stop playback
Press the stop button.
To switch the unit off after use
Turn the unit off by pressing the POWER switch. (The
indicators will go off except for the current time display.)
COMPACT DISC PLAYER OPERATION
POWER
POWER
Total number of tracks
Music calendar Total playing time
Receiver
CD Player
1
2, 4
1
3
5, 11, 22
5, 11, 22
TRACK TOTAL
2 3 4 5 6 7 8 9 10 11 12
HALL
1
DSP
ON
E-17
English
12345
12345
678
67890
E
+
I0
TUNER DIRECT
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
COMPACT DISC PLAYER OPERATION
Direct operation
Even when an input source other than CD player is selected,
pressing the play/pause button, a track number input button
or the RANDOM play button, or pressing the front edge of the
disc table gently will start playback directly. In this case, if
the tape deck is playing back a tape, it will be stopped
automatically.
* These ways of playback can also be used to close the disc
table. If the table is closed in these ways, playback will
begin automatically, however, the display will not show the
total number of tracks and the total playing time of the disc.
Precautions
If TV or radio interference occurs during CD player
operation, move the unit away from the TV or radio.
Subjecting the unit to shock or vibration can cause
mistracking.
Playing some compact discs at high volume can cause
mistracking. In this case, listen at lower volume.
Do not push the disc table while it is moving.
If the power fails while the table is open, wait until the
power supply returns or gently push the table manually to
close it.
The temperature range for playing compact discs is
recommended to be 5°C (41°F) – 35°C (95°F).
Direct-selection play
By using the track number input buttons on the remote
control transmitter, any track you wish to listen to can be
played directly.
Use the track number input buttons to select the desired
track number. Play will begin automatically.
A. For example, to choose selection 5
Press the “5” button.
B. For example, to choose selection 12
(1)Press the “+10” button.
(2)Within 3 seconds, press “2” button.
C. For example, to choose selection 20
(1)Press the “+10” button.
(2)Within 3 seconds, press the “+10” button again.
(3)Within 3 seconds, press the “0” button.
Note
A track number higher than the number of tracks on the disc
cannot be selected. Also, if a higher track number is selected
while the disc table is open, play will begin from the last track
on the disc when the disc table is closed.
E-18
COMPACT DISC PLAYER OPERATION
“Skip search” and “Manual search” are performed using the
same buttons.
Skip search
The beginning of any track can be found automatically.
1 Load a disc and begin playback.
2 Press the button to advance or button to
reverse through the disc.
Press once for each track to be advanced or reversed.
Press once to advance to the track following the
one now playing back.
Press once to return to the start of the track now
playing back.
Press twice to return to the track before the track
now playing back.
Notes
This function can also be performed while the unit is
stopped. Press the play/pause button when your desired
track number appears in the track number display.
Playback will begin from the beginning of the track.
This function will be performed forward or backward from
any point on the disc. However, it will not move forward
during playback of the final track.
Manual search
1 Begin playback.
2 Press and hold the button to advance play rapidly,
and the button to reverse play rapidly.
*
The sound can be heard (although slightly garbled)
during manual search in either direction. This is
convenient for reviewing the contents quickly.
Note
Manual search can also be performed while playback is
paused, though no sound will be heard.
CD Player
1
2
1
2
E-19
English
COMPACT DISC PLAYER OPERATION
Program play
You can program up to 20 tracks in any desired order.
1 Load a disc and close the disc table.
2 When in the stop mode, press the PROGRAM button to
prepare for programming.
* “PROG” and “P-01” illuminate on the display, and all
track numbers on the disc begin flashing.
3 Use the track number input buttons to select the desired
track number.
* The selected track number and the total play time of
the programmed tracks will illuminate on the display,
and soon it is replaced by the display of the next
playback order. Programmed track numbers will stop
flashing and illuminate on the music calendar.
* Pressing the TIME button displays the total play time of
the programmed tracks for about 1 second, and then it
is replaced by the display of the next playback order.
* For example, to choose selection 12
(1)Press the “+10” button.
(2)Press the “2” button.
4 Repeat step 3 for any other track. Up to 20 tracks can be
programmed.
5 Press the play/pause button to start playback of
programmed tracks.
Notes
It is also possible to program a sequence of tracks while
looking at the list of tracks on the surface of the disc
before closing the disc table.
During playback or pause, programming is not possible.
If the total time of the programmed tracks reaches 100
minutes or more, only the last two-digits will be displayed
for the three-digit number.
The total time of the programmed tracks will not be
displayed, if a track number higher than 19 is
programmed.
Skip search can be performed during playing back, but
only within the range of the programmed tracks.
Manual search can be performed during playing back to
search through all tracks, including unprogrammed tracks.
Playback order
Music calendar
Selected disc Total playing time
Display information during programming
Selected track number
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
CD Player
6 1
5
3
2
TRACK
PROG
2 3 4 5 6 7 8 9 10 11 12
HALL
1
DSP
ON
TRACK TOTAL
PROG
2 3 4 5 6 7 8 9 10 11 12
HALL
1
DSP
ON
/
E-20
To stop program play
Press the stop button. The first track number
programmed will be displayed.
To resume playback, press the play/pause / button.
Playback will begin from the beginning of the program.
To cancel a programmed sequence
There are several methods as described below.
Press the stop button while the unit is stopped.
Open the disc table
Switch off the power.
COMPACT DISC PLAYER OPERATION
To check program data
1. If during playing back, press the stop button.
2. Press the PROG button.
3. Each time the SKIP button is pressed, the track
numbers and sequential order of the programmed tracks
can be checked one after another. The display of the
track number can be returned (sequentially in reverse
order) by pressing the SKIP button.
To correct program data
1. Follow the procedure described in “To check program
data”.
2. Display the track number to be corrected by pressing the
SKIP button.
3. Press a track number input button to select a track to
replace the one displayed. The previously programmed
track will be cleared from the memory and the new one
will be programmed.
4. After the correction has been completed, press the
PROG button or play/pause / button once again.
/
CD Player
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
PROG
E-21
English
Repeat play
An entire disc, a single track or a programmed sequence can
be continuously repeated.
1 While watching the display, press the REPEAT button
once or more to select a desired repeat play mode (S
REP or F REP).
2 Press the play/pause button.
Repeat play modes
SINGLE REPEAT (S REP)
A single track is played back repeatedly.
* This is also available in the program play mode and the
random play mode. (If the repeat play mode is switched off,
the program play mode or the random play mode will be
resumed.)
FULL REPEAT (F REP)
An entire disc is played back repeatedly.
* In the random play mode, the disc is repeatedly played
back, but the order of tracks is different every time.
To cancel the repeat play
Press the REPEAT button once or more so that the (S, F)
REP indicator goes out.
COMPACT DISC PLAYER OPERATION
CD Player
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
2
1
2
off S REP F REP
TRACK
2 3 4 5 6 7 8 9 10 11 12
HALL
DSP
ON
TRACK REMAIN
2 3 4 5 6 7 8 9 10 11 12
HALL
DSP
ON
TRACK TOTAL
2 3 4 5 6 7 8 9 10 11 12
HALL
DSP
ON
TRACK TOTALREMAIN
2 3 4 5 6 7 8 9 10 11 12
HALL
DSP
ON
E-22
Random play
The tracks on the disc can be played back in a random order.
1 Load a disc and close the disc table.
2 Press the RANDOM button to begin random play.
* The “RANDOM” indicator will light up.
To cancel the random play
Press the stop button. The “RANDOM” indicator goes out.
Note
This feature will not function during programming, or during
program play.
Switching the time display
Each time the TIME button is pressed, the display will
change as described below.
[Example]
When the second track is being played back (Refer to the
illustration on the left.)
The elapsed play time for the track now playing back will
be displayed.
* 8 seconds have passed since the beginning of the
second track.
The remaining play time for the current track will be
displayed.
* 2 minutes and 58 seconds remain till the end of the
second track.
The total play time of the disc will be displayed.
(If the unit is in the program play mode, the total play time
of the programmed tracks will be displayed.)
The total remaining play time from the point being played
at that time will be displayed.
* 41 minutes remain till the end of the disc.
Notes
During random play, the total remaining play time on the
disc will not be displayed.
The total remaining play time will not be displayed for
track number 20 or higher.
COMPACT DISC PLAYER OPERATION
TIME
2 1
2
CD Player
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
E-23
English
Normally, if station signals are strong and there is no
interference, quick automatic-search tuning (Automatic
tuning) is possible. However, if signals of the station you
want to select are weak, you must tune to it manually
(Manual tuning).
Automatic tuning
1 Select the tuner so that “TUNER” appears on the display
by pressing the INPUT selector or button.
2 Select the reception band [FM or AM (MW or LW)] by
pressing the BAND button while watching the display.
3 Press the AUTO/MAN’L button so that “AUTO TUNING”
appears on the display.
(In this mode, stations are received in stereo or monaural
automatically.)
4 Press the TUNING UP button to tune to a higher
frequency, or press the TUNING DOWN button to tune to
a lower frequency.
5 If the station where tuning search stopped is not the
desired one, follow step 4 again.
* If the tuning search does not stop at the desired station,
change to the Manual tuning method as described below.
* STEREO indicator will illuminate when an FM stereo
broadcast with sufficient signal strength is received.
Manual tuning
11 Follow steps 1 and 2 of the Automatic tuning method.
22 Press the AUTO/MAN’L button so that “AUTO TUNING”
disappears from the display.
(In this mode, stations are received in monaural.)
33 Press and hold the TUNING UP button to tune to a higher
frequency, or press and hold the TUNING DOWN button
to tune to a lower frequency.
Release it just before reaching the desired frequency,
and then press it repeatedly until the desired frequency
appears.
Note
If you tune to an FM station manually, it is received in
monaural automatically to increase the signal quality.
“AM” is for Australia and General models.
“MW/LW” is for U.K. and Europe models.
TUNING OPERATION
Receiver
1
4, 33 3, 22 2
E-24
TUNING OPERATION
Preset tuning
This unit can store station frequencies selected by tuning
operation. With this function, you can select any desired
station by only calling the corresponding preset station
number. Up to 40 stations (8 stations x 5 areas) can be
stored.
To store stations
(Example: To store a station to A1)
1 Tune to a desired station.
(Refer to the previous page for tuning procedure.)
2 Press the MEMORY button.
* The MEMORY indicator will flash for about 5 seconds.
3 Select a desired area (A – E) by pressing the A/B/C/D/E
button while watching the display, before the MEMORY
indicator goes out.
(In this case, select area A)
4 Select a preset station number by pressing the TUNER
PRESET DOWN or UP button repeatedly before the
MEMORY indicator goes out.
(In this case, select “1”.)
5 Within about 5 seconds, press the MEMORY button
again.
* In the same way, program other stations to A2, A3 ... A8.
* You can program more stations to the preset station
numbers on other areas in the same way by selecting other
areas in step 2.
To recall a preset station
11 Select the area of preset station numbers by pressing the
A/B/C/D/E button.
22 Select the desired preset station number by pressing the
TUNER PRESET DOWN or UP button repeatedly.
Notes
A new setting can be programmed in place of the former
one.
For presets the setting of the AUTO/MAN’L button is
stored along with the station frequency.
For easier operation
By using the preset station number buttons and the
A,B,C,D,E selector buttons on the remote control transmitter,
a preset station number and an area can be selected directly.
Shows the displayed station
has been programmed to A1.
Receiver
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
4, 22
3, 11 2, 5
4, 22
3, 11
4, 22
3, 11
STEREO
AUTO TUNING
PRESET
MHz
HALL
DSP
ON
E-25
English
Automatic preset tuning
You can also make use of an automatic preset tuning
function. By this function, this unit performs automatic tuning
and stores stations with strong signals sequentially. Up to 40
stations are stored automatically in the same way as in the
manual preset tuning method on the previous page.
1 Select the tuner so that “TUNER” appears on the display
by pressing the INPUT selector or button.
2 Press and hold the AUTO MEMORY button for about 2
seconds.
* The MEMORY and AUTO TUNING indicators will flash.
This unit performs automatic tuning and received stations are
programmed to A1, A2 ... A8 sequentially.
After the automatic preset tuning is completed
The display shows the frequencies of the first preset station
(stored to A1).
Check the contents and the number of preset stations by
following the procedure of the section “To recall a preset
station” on the previous page.
To recall a preset station
Simply follow the procedure of the section “To recall a preset
station” on the previous page.
Notes
The automatic preset tuning search will be performed
through all frequencies until 40 stations are stored. If the
number of received stations is less than 40, the search will
stop after searching through all frequencies.
With this function, only stations with sufficient signal
strength are stored automatically. If the station you want
to program is weak in signal strength, tune to it in
monaural manually and program it by following the
procedure of the section “To store stations” on the
previous page.
You can replace a preset station by another FM or AM
(MW or LW) station manually by simply following the
procedure of the section “To store stations” on the
previous page.
TUNING OPERATION
Fundamental rules of internal automatic preset tuning
operation
Basically, FM stations are programmed onto area A, B and C,
and AM stations are programmed onto area D and E (MW
stations are onto D and LW stations are onto E) in that order
automatically.
* If, for example, the number of received FM stations is not
enough to fill up three areas (A, B and C), AM (MW or LW)
stations are programmed closely from the preceeding
empty areas. In such a case, AM (MW) stations are
programmed from area B or C (and LW stations are from
area C or D.)
* Moreover, one area is programmed with stations of the
same band only. If, for example, the last FM station is
programmed to B4, B5–B8 will be programmed with no
station, and AM (MW) stations are programmed from area
C.
Memory back-up
The memory back-up circuit prevents the programmed data
from being lost even if the AC supply lead is disconnected
from the AC outlet or the power is cut due to temporary
power failure. If, however, the power is cut for more than one
week, the memory may be erased. If so, it can be re-
programmed by simply following the Preset tuning steps.
Receiver
1
2
E-26E-26
TAPE DECK OPERATION
General information
Do not use C-120 tapes, tapes with internal reels or poor-
quality tapes, since they can cause malfunctions.
Before loading a tape into the cassette compartment,
tighten the slack tape with a pen or pencil.
Tapes have removable tabs which prevent accidental
recording or erasing from taking place. Removing the tab
on the top left protects the side facing you from erasure.
Cover the tab holes with adhesive tape to erase or record
again.
This deck is a Double Cassette Deck with Automatic
Reverse Function.
DECK A: Playback only.
DECK B: Playback or recording.
This deck features an auto tape selector. Just load the
tape, and the tape formula being used will be sensed
automatically.
This unit can play back metal tapes as well as normal or
chrome tapes, and recording can also be done on metal
tapes.
When covering erasure prevention tab holes, do not cover
the chrome and metal detection holes. Otherwise, the
deck will treat tape as normal tape.
Do not press the EJECT button during playback or
recording.
E-27
English
Tape A or tape B playback
1 Select the tape deck so that “TAPE” appears on the
display by pressing the INPUT selector or button.
2 Open the DECK A or DECK B cassette compartment by
pressing the EJECT button.
3 Load the tape into the DECK A or DECK B cassette
compartment, and close the lid panel completely by
pressing the upper part of the center of the panel as
figured left.
* If you loaded two tapes into both the DECK A and B
cassette compartments, select the DECK A or B in
which the tape to be played back is loaded by pressing
the DECK A or B select button.
4 Set the Dolby NR switch to B or C if the tape has been
recorded with Dolby noise reduction, and to OFF if Dolby
NR was not used.
* For selection of the Dolby B or C position, refer to the
“Dolby B and C Type Noise Reduction” on page 29.
5 Set the reverse mode switch as desired.
The reverse mode switch can be operated before or during
playback, and changes tape playback as follows:
6 Press the play button to listen to side A, or the
play button for side B.
To stop playback
Press the stop button.
Note
When removing the tape, press the stop button, and
then open the cassette compartment.
Direct operation
Even if an input source other than tape deck is selected,
pressing the play button (or the fast wind button) will start
playback (or fast winding) directly.
TAPE DECK OPERATION
3
DECK A select button
DECK B select button
Side A only
Side B only
Side A
Side
B
Side B only
Side A Side B
Continuous
play
(8 times)
Side B Side A
Continuous
play
(8 times)
Receiver
Tape Deck
2 5 6 6 4 2
1
E-28
Winding the tape
1 If during playback, first press the stop button.
2 Next press the fast wind or fast wind button to
wind the tape.
3 Press the stop button to stop.
* While winding the tape, the corresponding play direction
indicator flashes rapidly.
Note
When the tape is wound to the end, this unit will then function
as described below, according to the setting of the reverse
mode switch.
: The tape stops at the end.
: If the winding direction is , when the tape reaches
the end, playback automatically starts from the reverse
side.
If the winding direction is , the tape stops at the
end.
: When the tape reaches the end, playback
automatically starts from the reverse side.
Searching for the beginning of a
desired selection
Carry out the following operation during playback to find the
beginning of a desired selection on the tape.
To listen to the same selection
Press the button if the direction of the current playback
is .
Press the button if the direction of the current playback
is .
To listen to the next selection
Press the button if the direction of the current playback
is .
Press the button if the direction of the current playback
is .
* While searching, the corresponding play direction indicator
flashes slowly.
Notes
This function may not work for tapes with
* Material with long pauses or quiet passages.
* Low recording levels or excessive noise.
* Pauses of less than 4 seconds between selections.
If searching is carried out at the first or the last part of a
selection, the searching may not function correctly.
TAPE DECK OPERATION
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
Tape Deck
E-29
English
Continuous playback
1 Load the tapes into the DECK A and DECK B cassette
compartments.
2 Set the reverse mode switch to .
The reverse mode switch can be operated before or during
playback, and changes tape playback as follows:
3 Press the DECK A or B select button to select the tape to
be played back first.
4 Press the play button to listen to side A, or the
play button for side B.
Tape A Side A B Tape B Side A B
Continuous play (8 times)
Tape A Side B Tape B Side A B
Tape A Side A
Continuous play (8 times)
Dolby B and C Type Noise Reduction
With cassette tapes, the most noticeable form of noise is high
frequency hiss. To reduce this hiss noise, this unit has been
equipped with a newly developed Dolby C noise reduction
system in addition to its conventional Dolby B NR. Either type
of noise reduction may be selected with the switch provided.
Dolby B NR has a noise reduction effect of about 10 dB in
the high frequency range. The corresponding figure with
Dolby C NR is about 20 dB, but this is over the entire range
where the human ear is most sensitive to noise (2 kHz to 8
kHz). Also, Dolby C NR has the same noise reduction effect
at both high and low signal levels. In addition, Dolby C NR
improves the tape’s MOL (Maximum Output Level).
Dolby noise reduction is a 2 part process that acts both on
recording and playback; be sure that the noise reduction
button is set to the same position on record and play.
* Noise in the source material cannot be reduced with the
Dolby NR system.
Dolby and the double D mark are trademarks of Dolby
Laboratories Licensing Corp. Dolby noise reduction
system manufactured under license from Dolby
Laboratories Licensing Corp.
DOLBY B.C NR
<DECK A>
<DECK A>
TAPE DECK OPERATION
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
Tape Deck
3
4
4
3
1 2 4 4 1
Side A only
Side B only
Side A Side
B
Side B only
Side A Side
B
Side B only
When recording important selections, be sure to make a
preliminary test to ensure that the desired source material
is being properly recorded with good sound quality.
The automatic recording level control circuit automatically
controls the level of the input signal used for recording.
Adjusting the VOLUME, BALANCE, TREBLE and BASS
controls have no effect on the recorded sound.
If, however, the DSP is on, the DSP effect is recorded
along with the source.
* Music with DSP effect is suitable for listening to inside
a car etc.
For the tape deck, the deck which can be used for
recording is the DECK B only. When recording, be sure to
load a tape into the DECK B cassette compartment.
CD synchronized recording
1 Select the CD player so that “CD” appears on the display
by pressing the INPUT selector or button, and load
the disc to be recorded.
2 Load a tape into the DECK B cassette compartment.
* Wind past the beginning part of the tape on which
recording can not be performed.
3 When recording with the Dolby NR system, set the Dolby
NR switch to B or C; if not, set it to OFF.
* For selection of the Dolby B or C position, refer to the
“Dolby B and C Type Noise Reduction” on page 29.
4 Set the reverse mode switch as desired.
When the tape is set so that side A faces you, recording will
be done as follows automatically according to the selected
reverse mode.
5 Press the REC/PAUSE button.
* The corresponding indicator will light up and the play
direction indicators flash.
6 Start CD playback by pressing the play/pause button.
* Before CD playback begins, recording automatically
begins on the side of the tape now selected.
E-30
RECORDING A COMPACT DISC
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
Receiver
CD Player
Tape Deck
1
6
1
5
6
4 5 3 2
E-31
English
To stop recording temporarily
1 Press the stop button of the CD player.
2 Choose the selection to be recorded next by using the
SKIP or button, and then press the play button
of the CD player to resume recording (or simply press the
track number input button on the remote control
transmitter).
To stop recording
Press the stop button of the tape deck.
(At this time, CD playback does not stop.)
Recording programmed tracks
Programmed tracks can also be recorded in the same way.
1 Program desired tracks. (Refer to page 19 for the
programming procedure.)
2 Follow steps 2–5 on the previous page.
3 Press the play/pause / button of the CD player.
Notes
During CD Synchronized Recording, when more than 4
seconds elapse between tracks, the tape will stop
automatically and resume recording when the beginning
of the next track is found.
The CD Synchronized Recording will function even when
the CD player is turned into random play mode.
RECORDING A COMPACT DISC
/
CD Player
Tape Deck
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
/
E-32
Recording CD on both sides of a
tape automatically
1 Select the CD player so that “CD” appears on the display
by pressing the INPUT selector or button, and load
the disc to be recorded.
2 Load a tape into the cassette compartment.
3 When recording with the Dolby NR system, set the Dolby
NR switch to B or C; if not, set it to OFF.
* For selection of the Dolby B or C position, refer to the
“Dolby B and C Type Noise Reduction” on page 29.
4 Set the reverse mode switch to or .
5 Press the EDIT button. (“EDIT” appears on the display.)
CD playback and recording starts. Recording is carried
out on side A and B of the tape continuously.
* If the tape has not rewound to the end, it is rewound to
the end rapidly before recording starts.
Recording starts from the first part of the tape on which
recording can be done.
* “A ” (or “ B”) on the display shows the side of
the tape on which recording is being carried out.
* When the recording on side A finishes while a track is
being played back, the sound is automatically faded
out, and then the recording stops.
The recording on side B starts from the beginning of
the same track.
Note
The CD player’s repeat play mode will be canceled during
this recording mode.
Recording programmed tracks
Programmed tracks can also be recorded in the same way.
11 Program desired tracks. (Refer to page 19 for the
programming procedure.)
22 Follow steps 2–5 described above.
To cancel this function
Before recording, press the stop button of the CD player
or the tape deck.
To stop recording
Press the stop button of the tape deck.
(At this time, CD playback automatically stops.)
RECORDING A COMPACT DISC
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
Receiver
CD Player
Tape Deck
1
1
5
1
4 3 2
E-33
English
Automatic tape-editing
This convenient feature can be used to program tracks on a
disc for recording to tape. By only memorizing the tape’s total
possible recording time, the unit will automatically program
tracks or help you to program tracks so they will fit onto the
tape with the least amount of unrecorded space remaining at
each end of the tape.
To record a disc with the order of tracks
unchanged
1 Select the CD player so that “CD” appears on the display
by pressing the INPUT selector or button, and load
the disc to be recorded.
2 Load a tape into the cassette compartment.
3 When recording with the Dolby NR system, set the Dolby
NR switch to B or C; if not, set it to OFF.
* For selection of the Dolby B or C position, refer to the
“Dolby B and C Type Noise Reduction” on page 29.
4 Set the reverse mode switch to or .
5 Press the TAPE button to select the length of the tape to
be used. Whenever pressed, C-46, C-54, C-60 and C-90
appear on the display in turn, and next it returns to the
normal display mode.
When using tapes other than C-46, C-54, C-60 or C-90
When C-46, C-54, C-60 or C-90 is appearing on the
display, input the tape length by using the track number
input buttons on the remote control transmitter
(Examples)
C-62: Press “6” and then “2”.
C-30: Press “3” and then “0”, or press “+10” three times
and then “0”.
6 Press the EDIT button. (“EDIT” appears on the display.)
The following internal operations are carried out before
recording is automatically started.
1)Tracks on the disc are automatically divided between
side A and side B. You can check the process by
watching the display.
2)The end part of the tape on which recording cannot be
done is wound.
3)This unit starts searching for a peak level through all
tracks to be recorded. (While searching, “LEVEL”
flashes on the display.) When searching is finished, this
unit adjusts the recording level properly on the basis of
this data.
4)CD playback and recording starts. Recording is carried
out on both side A and B of the tape.
off C-46 C-54 C-60 C-90
→→
RECORDING A COMPACT DISC
Receiver
CD Player
Tape Deck
1
1
4 3 2
5
6
5
1
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
E-34
RECORDING A COMPACT DISC
Note
The CD player’s repeat play mode will be canceled during
this recording mode.
To cancel tape-editing function
Before recording, press the stop button of the CD player
or the tape deck.
To stop recording
Press the stop button of the tape deck.
(At this time, CD playback automatically stops.)
To make this unit program tracks on a disc
automatically so that the least amount of
unrecorded space remains on the tape
1 Follow steps 1–5 on the previous page.
2 Press the PROGRAM button.
3 Press the TAPE button.
“AP A
> ” illuminates during programming for side A, and
“AP B
> ” illuminates during programming for side B.
* After “AP B
> ” goes out from the display, you can
check the programmed contents for side A and B
respectively.
To check, cancel or correct program data, refer to page
20.
4 Press the EDIT button. (“EDIT” appears on the display.)
The recording is automatically started.
* The unit searches for a peak level on each track to
adjust the recording level properly. The search is
carried out before recording each track. (While
searching, “LEVEL” flashes on the display, and
recording is paused.)
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
CD player
Tape Deck
3
4
2
E-35
English
RECORDING A COMPACT DISC
To record programmed tracks
1 Select the CD player so that “CD” appears on the display
by pressing the INPUT selector or button, and load
the disc to be recorded., and load a disc on the disc table.
2 Follow steps 2–5 on page 33.
3 Press the PROGRAM button.
* “PROG” and “P-01” illuminate on the display, and all
track numbers on the disc begin flashing.
4 Use the track number input buttons to select the desired
track number.
5 Repeat step 4 to set more programs for the side A of the
tape. You can select the same track again.
* Pressing the TIME button displays the total remaining
time on the side of the tape for about 1 second, and
then it is replaced by the display of the next playback
order.
* If “ERR” appears on the display, the track number just
selected cannot be programmed because there is not
enough time remaining on the side A of the tape.
However, at this time, if any other track number is
flashing continuously on the display, you can program
it instead of the unprogrammable one.
6 After you finish the programming for the side A, press the
TAPE button.
* “Pu” appears on the display, then you can begin
programming for side B.
7 Repeat step 4 to set more programs for the side B of the
tape. You can select the same track again.
* If “ERR” appears on the display, the track number just
selected cannot be programmed because there is not
enough time remaining on the side B of the tape.
However, at this time, if any other track number is
flashing continuously on the display, you can program
it instead of the unprogrammable one.
8 Press the EDIT button. (“EDIT” appears on the display.)
The recording is automatically started.
* The unit searches for a peak level on each track to
adjust the recording level properly. The search is
carried out before recording each track. (While
searching, “LEVEL” flashes on the display, and
recording is paused.)
Notes on tape-editing
To check, cancel or correct program data, refer to page
20.
The maximum number of tracks that can be programmed
is 20.
This function can be used to program up to track number
20. If the disc has more than 20 tracks, track number 20
and thereafter will not be programmed.
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
Receiver
1
CD Player
1
4
1
3
6
8
A
TRACK
PROG
2 3 4 5 6 7 8 9 10 11 12
HALL
1
DSP
ON
Display information during programming
Side of the tape
Next playback order
A
TRACK REMAIN
PROG
2 3 4 5 6 7 8 9 10 11 12
HALL
1
DSP
ON
Selected track number
Total remaining time on
the side of the tape
Programmed track numbers illuminate and
unprogrammed ones flash.
E-36
Recording from the built-in tuner
1 Select the tuner so that “TUNER” appears on the display
by pressing the INPUT selector or button.
2 Tune to the desired station. (Refer to the “TUNING
OPERATION” on pages 23 and 24.)
3 Load a tape into the cassette compartment.
4 When recording with the Dolby NR system, set the Dolby
NR switch to B or C; if not, set it to OFF.
* For selection of the Dolby B or C position, refer to the
“Dolby B and C Type Noise Reduction” on page 29.
5 Set the reverse mode switch to to record on only one
side, or to (or ) for continuous recording on both
sides.
6 Press the REC/PAUSE button.
* The corresponding indicator lights up and the play
direction indicators flash.
7 Press the play button to record on side A, or the play
button to record on side B.
* For continuous recording on both sides, begin on side
A. Recording stops automatically at the end of side B.
To stop recording temporarily
11 Press the REC/PAUSE button.
22 To resume recording, press the play button whose
indicator is flashing.
To stop recording
Press the stop button.
OTHER RECORDINGS
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
Receiver
1
5
7, 22 6, 11 7, 22
Tape Deck
4 3
1
7, 22
7, 22
6, 11
Dubbing
During dubbing, adjusting the VOLUME, BALANCE,
TREBLE and BASS controls have no effect on the
recorded sound.
If, however, the DSP is on, the DSP effect is recorded
along with the source.
* Music with DSP effect is suitable for listening to inside
a car etc.
Try to use the same tape formula and length for the
recording tape as for the master tape.
1 Select the tape deck so that “TAPE” appears on the
display by pressing the INPUT selector or button.
2 Load a prerecorded tape into the DECK A cassette
compartment. Insert a blank tape into the DECK B
cassette compartment.
3 Set the reverse mode switch to to record on only one
side, or to (or ) for continuous recording on both
sides.
4 Press the DUBBING button.
* Press “NORMAL” to dub at normal speed, and “HIGH”
to dub at about twice the normal speed.
* Dubbing will begin from side A regardless of the side
now selected.
To stop dubbing
Press the stop button.
* Tape A and tape B will stop at the same time.
Note
Only tapes originally encoded with Dolby B or C NR will be
dubbed onto tapes with Dolby B or C NR encoding.
The Dolby NR switch will have no effect on the recording of
tape B during dubbing.
However, the playback tonal quality of tape A will change
according to the Dolby NR switch position.
Erasing recorded tapes
11 Load the tape to be erased into the DECK B cassette
compartment.
22 Select the tape deck so that “TAPE” appears on the
display by pressing the INPUT selector or button.
33 Set the reverse mode switch to to erase only one
side and to (or ) to
erase both sides.
44 Press the REC/PAUSE button, then press the play
button to erase side A of the tape, or the play button to
erase side B.
E-37
English
OTHER RECORDINGS
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
1, 22
Receiver
Tape Deck
44 3, 33 44 44
44
1, 22
44
44
2 4 2, 11
E-38
HOW TO USE THE BUILT-IN TIMER
Timer play
By using the built-in timer, you can set the time when the unit
turns on and a source begins playing automatically, and the
time when the unit turns off automatically.
1 Prepare the source to be played.
For tuner:
Tune in to the station you will listen to.
For tape deck:
Load a tape into the cassette compartment.
(If tapes are loaded in both the compartments, tape A
takes priority of tape B, and is played back by the timer
play.)
For CD player:
Load a disc on the disc table.
2 Press the DISPLAY button.
Whenever the DISPLAY button is pressed, the display
mode changes as follows.
At each mode, make a setting for the timer play, referring
to the setting procedure described below.
Current time (TIMER on/off mode)
Source selecting mode (TAPE, TUNER, CD)
ON TIME/Time setting mode
OFF TIME/Time setting mode
Normal display mode
* The display mode will be changed to the next mode
after about 8 seconds elapse automatically. If the mode
is changed before the setting is completed, call the
mode again by pressing the DISPLAY button once or
more.
Setting procedure:
At the display of current time
Check to be sure that the current time is correct, and
press the TIMER button so that “TIMER” appears on
the display.
At source selecting mode
Select the source (TAPE, TUNER or CD) to be played
by pressing the INPUT selector or button.
* If “TUNER” is selected, soon it is changed to the
frequency display mode. In this mode, you can
select the station to listen to with the timer play by
using the BAND button, A/B/C/D/E button and
TUNER PRESET DOWN/UP buttons.
→→
2 2- 2-
Receiver
E-39
English
At ON TIME/time setting mode
[“ON TIME” appears on the display, and soon it is
changed to a time setting mode.]
Set to the time when the timer play begins by using
the HOUR button and the MINUTE button.
At OFF TIME/time setting mode
[“OFF TIME” appears on the display, and soon it is
changed to a time setting mode.]
If necessary, set to the time when you want to finish
the timer play (to turn this unit off) by using the HOUR
button and the MINUTE button. Even if you do not set
the time, it has already been set so that the timer play
finishes after 1 hour.
* The TIMER button functions also in the time (ON
TIME or OFF TIME) setting mode.
3 If you will not use this unit until the timer play begins, turn
the power off by pressing the POWER switch or the
TIMER button.
Note
If a timer play setting is made and the power is not turned off,
the source set for the timer play will begin playing when the
time comes in place of the source played at that time.
To cancel the timer play setting
After the timer play is finished, press the DISPLAY button to
call the current time. While the current time is displayed,
press the TIMER button so that “TIMER” goes out from the
display.
If it is not canceled, the system will be turned on at the same
time every day, so it can be used as an alarm. However, if
you will be out at that time, cancel the timer play setting.
* Unless the AC supply lead is unplugged or there is a
power failure for more than 30 minutes, the time set on
the timer will be retained until it is reset.
How to make time setting in the ON TIME or OFF
TIME mode
For the hour:
Press the HOUR button to change the hour to a higher value.
Press and hold to change continuously.
To change the hour to a lower value, while pressing the TIME
ADJUST button, press the HOUR button.
For the minute:
Use the MINUTE button and operate it in the same way as
you did to change the hour.
HOW TO USE THE BUILT-IN TIMER
POWER
TIME ADJ
Receiver
DISPLAY TIMER
2-,
E-40
To begin CD playback from a desired track by the
timer play.
1. Play back the track which you want to play back from the
beginning of the timer play.
2. Press the RESUME button on the CD player so that “
appears on the display.
3. Make the timer play setting.
4. Turn the power off while the track is being played back.
when the time comes, the timer play begins from the
beginning of the track.
* If you will not play back a CD from a designated track by
the timer play, press the RESUME button so that “
disappears from the display.
Timer recording
(To record a tuner program)
1 Load a blank tape into the DECK B cassette
compartment.
2 Tune to the station of which program you want to record.
3 Follow step 2 of the “Timer play” on pages 38 and 39.
* In step 2-, select “TUNER” by pressing the INPUT
selector or button, and then press the TIMER
REC button so that “REC” and the station frequency
flashes alternately.
4 If desired, change the setting of the reverse mode switch
and the Dolby NR switch.
5 If you will not use this unit untill the timer recording
begins, turn the power off by pressing the POWER switch
or the TIMER button.
To confirm the timer time setting
Press the DISPLAY button.
To cancel the setting of timer recording
Press the DISPLAY button once or more so that “REC”
flashes on the display. While “REC” is flashing, press the
TIMER REC button.
* Unless the AC supply lead is unplugged or there is a
power failure for more than 30 minutes, the time set on
the timer will be retained until it is reset.
Note
When the timer recording is finished, the timer setting is
automatically canceled to avoid repeating timer recording of
the same setting.
HOW TO USE THE BUILT-IN TIMER
Receiver
CD Player
DISPLAY TIMER
POWER
Tape Deck
4 4 1
TIMER REC
INPUT
RESUME
E-41
English
HOW TO USE THE BUILT-IN TIMER
Sleep timer operation
This unit can be turned off automatically.
1 Play the desired sound source.
2 Press the SLEEP button. “SLEEP” appears on the display,
and soon it is replaced by “120”.
3 Press the SLEEP button repeatedly until the desired sleep
time appears in the display. The display will change as
described below. (Time is displayed by the minute.)
* The original display mode will resume about 4 seconds
after the selection is made.
* The SLEEP indicator illuminates to indicate that the
sleep timer is on.
4 The unit will turn off automatically when the preset sleep
time has passed.
To confirm the sleep time setting
Press the SLEEP button once. “SLEEP” appears on the
display, and soon it is replaced by the remaining time of the
preset sleep time.
To change the sleep time
While the SLEEP indicator illuminates, press the SLEEP
button repeatedly until the desired time appears.
To stop the sleep timer operation
Press the POWER switch, or press the SLEEP button
repeatedly until “OFF SLEEP” appears on the display.
(The SLEEP indicator will go out.)
To set the sleep time using front panel buttons
First press the DISPLAY button to display the current time.
Within 7 seconds, press the AUTO MEMORY button.
Whenever the AUTO MEMORY button is pressed, the sleep
time changes.
Using the timer and the sleep
timer at the same time
1 Prepare timer playback. (See pages 38 and 39.)
* Do not turn the power of this unit off after the timer
setting is finished.
2 Press the SLEEP button and set the sleep time.
When the sleep timer operation finishes, the timer will
function to turn the source on at the preset time.
Notes
Do not set the timer time so that the timer will start during
sleep timer operation. (Since sleep timer operation has
priority, the timer will not operate.)
If the power is turned off by the sleep timer while playing
back a CD with “ ” is illuminated on the display, when
CD playback begins at the time set on the timer play
setting, playback begins from the beginning of the track
which had been being played back when the power was
turned off by the sleep timer.
* The “ ”indicator is switched on and off by pressing
the RESUME button on the CD player.
OFF SLEEP
(Sleep timer is off.)
120 90 60 30
-
+
12345
12345
678
67890
ABCDE
TIME
PROG
TAPE EDIT
+
I0
STOP
PLAY/PAUSE
RANDOM
REPEAT
CD
TUNER
TAPE
PRESET
DOWN UP
PLAY STOP
REC/PAUSE
SLEEPPOWER
DISPLAY
VOLUME
DECK
PHONO/AUX
TUNER DIRECT
A/B
A/B/C/D/E
PLAY
EFFECT LEVEL DSP MODE
SP/PHONES
-
+
Receiver
POWER
DISPLAY AUTO MEMO
POWER
SLEEP
E-42
Auxiliary (AUX)
1 Connect the output lead of a video cassette player, video
disc player, etc. to the AUX inputs of this unit.
(red right channel, white left channel)
2 Press the INPUT selector or button once or more
until “AUX” appears on the display.
3 Operate the unit connected to the AUX inputs.
4 Start recording with this unit, if so desired. (See page 36.)
Turntable (PHONO)
1 Connect the output lead of a turntable.
(red right channel, white left channel)
2 Connect the GND lead of a turntable.
3 Press the INPUT selector or button once or more
until “PHONO” appears on the display.
4 Operate the turntable.
5 Start recording with this unit, if so desired. (See page 36.)
USING EXTERNAL UNITS
E-43
English
PHONES
Headphones
Be sure that your headphones have a 3.5 mm (1/8”)
diameter plug and are between 16 ohms and 50 ohms
impedance. Recommended impedance is 32 ohms.
When headphones are connected, the speakers are
defeated automatically. Adjust the VOLUME control for
desired volume.
Internal care
Dirty heads, capstans and pinch rollers can cause poor
sound and tape jams.
Clean these parts with a cotton swab moistened with
commercially available head/pinch roller cleaner or
isopropyl alcohol, or with a commercially available
cleaning tape.
After long use, the deck’s heads and capstans may
become magnetized, causing poor sound. Demagnetize
these parts once every 30 hours of playing/recording time
by using a commercial tape head demagnetizer. Read the
demagnetizer’s instructions carefully before use.
External care
Periodically clean the surfaces of this system, especially
the top panel of the receiver to prevent the ventilation
holes from being blocked with dust etc.
Do not use chemically treated cleaning cloths or other
chemicals. (See “Precautions”.)
USING EXTERNAL UNITS
MAINTENANCE
DECK B
DECK A
E-44
SPECIFICATIONS
As a part of policy of continuous improvement, YAMAHA reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of production
units.
Receiver (RX-S50)
Minimum RMS Output Power per Channel
6 ohms, 50 Hz to 20 kHz, 0.08% THD .......................... 35W+35W
6 ohms, 1 kHz, 10% THD
[U.K. and General models only] ............................... 50W+50W
DIN Standard Output Power per Channel [Europe model only]
6 ohms, 1 kHz, 1% THD .......................................................... 40W
IEC Power [Europe model only]
6 ohms, 1 kHz, 0.1% THD ....................................................... 35W
Input Sensitivity/Impedance
PHONO MM ....................................................... 2.5 mV/47 k-ohms
AUX .................................................................. 300 mV/20 k-ohms
Headphone Output Impedance.......................................... 68 ohms
Total Harmonic Distortion (20 Hz to 20 kHz)
AUX to SP OUT (17.5W/6 ohms) ......................................... 0.08%
Tone Control Characteristics
BASS: Boost/cut ................................................... ±10 dB (50 Hz)
TREBLE: Boost/cut ............................................. ±10 dB (20 kHz)
Tuning Range
FM
[Australia, Europe, U.K. and General models]
...................................................................... 87.5 to 108.0 MHz
AM (MW)
[General model] ........................................... 530 – 1,710 kHz
[Australia, U.K. and Europe models] ......... 531 – 1,611 kHz
LW
[U.K. and Europe models only] ..................... 153 – 288 kHz
Usable Sensitivity
FM (75 ohms)
(30 dB S/N Quieting, 1 kHz, 100% mod.)
[Except Europe model]................................1.2 µV (12.8 dBf)
(DIN, Mono, S/N 26 dB) [Europe model] ........................1.5 µV
AM (MW)........................................................................ 280 µV/m
LW ................................................................................. 560 µV/m
Power Supply
[Australia and U.K. models] ............................. AC 240V, 50 Hz
[Europe model] ................................................. AC 230V, 50 Hz
[General model] ...................... AC 110/120/220/240V, 50/60 Hz
Power consumption
[Australia, Europe, U.K. and General models] ............... 120W
Dimensions (W x H x D)............................. 280 x 107.5 x 339.5 mm
(11” x 6-7/8” x 13-3/8”)
Weight ............................................................ 5.3 kg (11 lbs. 11 oz.)
CD player (CDX-S50)
Power Source ................................... AC supplies from receiver unit
Type ................................................................. Compact Disc Player
Signal Readout
........................... Non-contact, 3-beam semi-conductor laser pick-up
D/A Converter ................................................................... 1-bit DAC
Filter ......................................8-time oversampling 18-bit digital filter
Wow and Flutter .........................................Below measurable limits
Dimensions (W x H x D)............................. 280 x 107.5 x 322.5 mm
(11” x 6-7/8” x 12-11/16”)
Weight .............................................................. 3.0 kg (6 lbs. 10 oz.)
Tape Deck (KXW-S70)
Power Source ................................... AC supplies from receiver unit
Type ............... Auto Reverse 4-Track 2-Channel playback/recording
and playback stereo double Cassette Deck
Heads ................................................ PB, REC/PB : Hard Permalloy
Erase : Double Gap Ferrite
Motors ................................................................ DC servo motor x 2
Wow and Flutter ................................................. 50.19%, W.PEAK
0.09%, W.RMS
Fast Winding Time (C-60 Tape) ........................ About 120 seconds
Frequency Response (–20 dB)
........................................................ 30 – 15,000 Hz 53 dB (Normal)
30 – 16,000 Hz 53 dB (CrO
2
)
30 – 18,000 Hz 53 dB (Metal)
Signal-to-Noise Ratio .................................. 58 dB (Dolby NR OFF)
66 dB (Dolby B NR ON)
74 dB (Dolby C NR ON)
Harmonic Distortion.......................................... No more than 1.2%
Channel Separation (Input Shorted 1 kHz)
................................................................................. More than 40 dB
Crosstalk (Input Shorted 125 Hz).......................... More than 55 dB
Dimensions (W x H x D)................................ 280 x 117.5 x 326 mm
(11” x 4-5/8” x 12-13/16”)
Weight ................................................................ 4.2 kg (9 lbs. 4 oz.)
Speaker (NX-S50)
Type .................................................... Active Servo Processing type
Speakers ........................................................ 13 cm (5-1/8”) woofer
5 cm (2”) tweeter
Frequency Range .................................................... 50 – 20,000 Hz
Sound Pressure Level.......................................................... 88.5 dB
Maximum Power Handling Capacity........................................ 50W
Impedance ............................................................................ 6 ohms
Dimensions (W x H x D)................................ 170 x 332.5 x 222 mm
(6-11/16” x 13-1/16” x 8-3/4”)
Weight .......................................................... 3.3 kg (7 lbs. 4 oz.) x 2
E-45
English
E-45
CAUSE
AC supply lead is not plugged in.
Loose speaker connections.
Internal protection circuit is functioning.
Interference from starting motor of nearby car.
Interference from thermostat of nearby electrical
appliance.
Antenna input is too weak due to obstructions or
excessive distance from broadcasting station.
Insufficient antenna input.
Preset memory has been erased.
Interference from source such as lightning,
flourescent lights, electric motors or thermostat
of nearby electrical appliance.
TV or microprocessor is being used nearby.
Radio signal is weak or antenna is not properly
connected.
Current time is not set.
The internal microcomputer has been frozen by
an external electric shock (lightning, excessive
static electricity, etc.) or power supply with low
voltage.
Disc is upside down.
Disc is dirty.
Input selector setting is incorrect.
Disc is dirty.
Volume set too high.
Slack tape wrapped around pinch roller.
Erasure prevention tab is broken off.
Head is dirty.
Head is dirty.
Head has become magnetized.
Tape is worn.
Dolby NR switch is set to wrong position.
Head is dirty.
Head is dirty.
Head has become magnetized.
Tape is worn.
Slack tape coming out of cassette shell.
Tape is creased or torn.
Endless tape is being used.
Silent gaps between selections are too short.
Excessively soft passages in middle of
selections.
Conversation etc. is recorded.
Batteries are dead.
Remote control is too far away or is being used
at incorrect angle.
Direct sunlight or lighting (of an inverter type of
flourescent lamp etc.) is striking the remote
control sensor of the main unit.
Remote control is being used near TV set with a
remote control sensor.
SYMPTOM
No power even if the POWER switch is
pressed.
No sound from one speaker
No sound from speakers.
Excessive static in FM broadcasts.
Noise increases during stereo broadcasts.
Stereo broadcasts are noisy and STEREO
indicator blinks on and off.
Cannot select preset stations.
Buzzing or static during AM (LW or MW)
broadcasts.
AM (LW or MW) broadcast sensitivity is poor.
Can’t set timer.
This unit will not operate properly.
Play does not begin even if disc is loaded.
No sound.
Sound stops suddenly (always at same spot).
Tape won’t move during playback or
recording.
Can’t record.
Sound is distorted or fades out.
Poor sound quality.
Stereo balance is poor.
Excessive noise.
Tape travel stops in middle of playback or
recording.
Can’t find the beginning of desired selections
on tape.
Remote control doesn’t work.
TV functions strangely when the remote
control is used.
TROUBLESHOOTING
If your unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your
authorized YAMAHA dealer or service center for help.
Should be service required, the servicer will need all three pieces (RX-S50, CDX-S50, KXW-S70).
REMEDY
Plug in the AC supply lead.
Connect properly.
Unplug the AC supply lead from the wall AC outlet, and then
plug in again.
Position the FM antenna as high and as far away from
nearby roads as possible. Connect using a coaxial cable.
Check antenna connections.
Install a multi-element type FM antenna if possible.
Install an antenna appropriate for the electric field strength of
your area.
Reprogram memory presets.
Problem is difficult to eliminate but can be lessened by
grounding MW/LW (AM) loop antenna.
Move away from TV or microprocessor.
Properly connect MW/LW (AM) loop antenna.
Change orientation of MW/LW (AM) loop antenna.
Install an external MW/LW (AM) antenna.
Set current time.
Unplug the AC supply lead from the wall AC outlet, and then
plug in again after about one minute.
Load disc label side up.
Clean disc.
Select “CD” by the INPUT selector buttons.
Clean disc.
Lower volume.
Take up slack with a pencil before using.
Replace tape or cover erasure prevention hole with
cellophane tape.
Clean heads.
Clean heads.
Demagnetize heads with head eraser.
Replace tape.
Set to positions matching those used when tape was
recorded.
Clean heads.
Clean heads.
Demagnetize heads with head eraser.
Replace tape.
Take up slack by turning reels with a pencil.
Replace with new tape.
Don’t use endless tapes.
The function for searching the beginning of desired
selections won’t operate unless the silent gaps between
selections are at least four seconds long.
Replace batteries.
Use within 6 m and 60° radius.
Change position of the main unit.
Move TV farther away or cover its remote control sensor.
RECEIVERCD PLAYER
REMOTE CONTROL
TAPE DECK
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
VQ 98180

Transcripción de documentos

CC-50 Natural Sound Mini Component System Chaîne Mini de la série “Natural Sound” Natural Sound Mini Komponenten-System Natural Sound Mini Komponent System Sistema di Componenti Mini a Suono Naturale Sistema de Componentes con Sonido Natural Natural Sound Mini Component Systeem Active Servo Technology CC-50: RX-S50 + CDX-S50 + KXW-S70 + NX-S50 OWNER‘S MANUAL MODE D‘EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING SUPPLIED ACCESSORIES ACCESSOIRES FOURNIS MITGELIEFERTES ZUBEHÖR MEDFÖLJANDE TILLBEHÖR ACCESSORI IN DOTAZIONE ACCESORIOS INCLUIDOS BIJGELEVERDE ACCESSOIRES ● ● ● ● ● ● ● After unpacking, check that the following parts are contained. Après le déballage, vérifier que les pièces suivantes sont incluses. Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind. Kontrollera efter det apparaten packats upp att följande delar finns med. Verificare che tutte le parti seguenti siano contenute nell’imballaggio dell’apparecchio. Desembale el aparato y verificar que los siguientes accesorios están en la caja. Controleer na het uitpakken of de volgende onderdelen voorhanden zijn. ● ● ● ● ● ● ● Remote control transmitter Télécommande Fernbedienung Fjärrkontroll Telecomando Controlador remoto Afstandbediening ● ● ● ● ● ● ● AM (MW/LW) loop antenna Cadre-antenne AM (PO/GO) MW/LW-Rahmenantenne MV/LV ramantenn Antenna ad anello per AM (MW e LW) Antena de cuadro AM (OM/OL) AM (MW/LW) lusantenne TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PRESET REPEAT RANDOM DOWN UP PLAY STOP DECK PLAY 0 TAPE PHONO/AUX REC/PAUSE ● A/B EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE SP/PHONES VOLUME - + ● ● ● ● ● ● ● ● ● ● ● ● ● Batteries (size AA, UM/SUM-3, R6, HP-7) Piles (format AA, UM/SUM-3, R6, HP-7) Batterien (Größe AA, UM/SUM-3, R6, HP-7) Batterier (Storl. AA, UM/SUM-3, R6, HP-7) Batterie (dimensioni AA, o UM/SUM-3, o R6, o HP-7) Pilas (tamaño AA, tipo UM/SUM-3, R6, HP-7) Batterijen (maat AA, UM/SUM-3, R6, HP-7) ● ● ● ● ● ● ● Indoor FM antenna Antenne intérieure FM UKW-Innenantenne FM inomhusantenn Antenna FM per interni Antena interior de FM FM binnenantenne Speaker cords Câbles d’enceintes Lautsprecheranschlußkabel Högtalarledningar Cavi per gli altoparlanti Cables de los altavoces Luidsprekerdraden This product complies with the radio frequency interference requirements of the Council Directive 82/499/EEC and/or 87/308/EEC. Cet appareil est conforme aux prescriptions de la directive communautaire 87/308/CEE. Diese Geräte entsprechen der EG-Richtlinie 82/499/EWG und/oder 87/308/EWG. Dette apparat overholder det gaeldende EF-direktiv vedrørende radiostøj. Questo apparecchio è conforme al D.M.13 aprile 1989 (Direttiva CEE/87/308) sulla soppressione dei radiodisturbi. Este producto está de acuerdo con los requisitos sobre interferencias de radio frequencia fijados por el Consejo Directivo 87/308 CEE. Dit product voldoet aan de EEG normen betreffende radio-frekwentie storingen 82/499/EEG en/of 87/308/EEG. ENGLISH Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment. For the best performance, read this manual carefully. It will guide you in operating your YAMAHA product. FEATURES • • • • • • • • • • • • • • • 35W + 35W (6Ω) RMS Output Power, 0.08% THD, 50–20,000 Hz 4-Mode Digital Sound Field Processor (DSP) Digital Sound Field Effective Even by Listening with Headphones Random Access Programmable CD Playback Single Track/Entire Disc Repeat Play Random-sequence Play Automatic Synchronized Recording with CD Playback Automatic CD Editing Function for Recording to Tape Double Cassette Tape Deck with Automatic Reversing Function 2-Way Speed Dubbing Dolby B/C Noise Reduction System 40 Station Automatic Preset Tuning Multi-Use Timer/Sleep Timer Active Servo Processing Speaker System (NX-S50) Remote Control Capability CONTENTS Page DIGITAL SOUND FIELD PROCESSOR (DSP) CONTROL ............................................................................14 COMPACT DISC PLAYER OPERATION.......................15-22 TUNING OPERATION ....................................................23-25 TAPE DECK OPERATION ............................................26-29 RECORDING A COMPACT DISC ..................................30-35 OTHER RECORDINGS...................................................36-37 HOW TO USE THE BUILT-IN TIMER.............................38-41 USING EXTERNAL UNITS .............................................42-43 MAINTENANCE ...................................................................43 SPECIFICATIONS................................................................44 TROUBLESHOOTING .........................................................45 Page PRECAUTIONS ..................................................................2-3 ACTIVE SERVO TECHNOLOGY ..........................................3 NAMES OF CONTROLS, INDICATORS AND REAR PANEL PARTS ........................................................4-6 REMOTE CONTROL TRANSMITTER................................7-9 PREPARATION FOR USE .............................................10-11 OPEN/CLOSE THE CONTROL DOOR ...............................12 TURNING THE POWER ON/OFF TO THIS SYSTEM .........12 SETTING THE CLOCK ........................................................13 SOUND CONTROL ..............................................................14 E-1 English INTRODUCTION PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT ■ To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. • ■ This system is equipped with the newly developed Active Servo Processing Speaker System. It is not designed for use with conventional speakers. Therefore, do not attempt to connect other speakers than the provided speaker system. • ■ Choose the installation location of this unit carefully. Avoid placing it in direct sunlight or close to a source of heat. Also avoid locations subject to vibration and excessive dust, heat, cold or moisture. Keep it away from sources of hum such as transformers and electric motors. • CD pickup Leave the power on with no disc in the unit until normal playback is possible (about 1 hour). Tape head Leave the power on with no cassette in the unit until normal playback is possible (about 1 hour). Note If condensation forms on the tape head, foreign matter may accumulate during use. Remote control Wipe off condensation on the transmitter window with a soft cloth before operating the unit. ■ Do not operate this unit upside-down. It may overheat, possibly causing damage. ■ Never open the cabinet. If something drops into the set, contact your dealer. IMPORTANT Please record the serial number of this unit in the space below. ■ The openings on the cabinet assure proper ventilation of the unit. If these openings are obstructed, the temperature inside the cabinet will rise rapidly and eventually damage the circuits. Therefore, avoid placing objects against these openings and do not install the unit where the flow of air through the ventilation openings could be impeded. Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference. ■ Always set the VOLUME control to “0” before starting the audio source play: increase the volume gradually to an appropriate level after the play has been started. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. ■ When not planning to use this unit for long periods of time (ie., vacation, etc.), disconnect the AC power plug from the wall outlet. CAUTION (FOR CANADA MODEL) TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT. ■ Grounding or polarization – Precautions should be taken so that the grounding or polarization of an appliance is not defeated. FOR CANADIAN CUSTOMER THIS DIGITAL APPARATUS DOES NOT EXCEED THE “CLASS B” LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS SET OUT IN THE RADIO INTERFERENCE REGULATION OF THE CANADIAN DEPARTMENT OF COMMUNICATION. ■ Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power plug and the wires connected to other equipment. Never pull the wire itself. ■ Do not attempt to clean the unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. ■ Be sure to read the “TROUBLESHOOTING” section regarding common operating errors before concluding that the unit is faulty. NOTE Please check the copyright laws in your country to record from records, compact discs, radio, etc. Recording of copyright material may infringe copyright laws. ■ To prevent lightning damage, disconnect the AC power plug and the antenna cable when there is an electrical storm. ■ Do not plug the AC power plug to the wall socket before you finish all connections. CAUTION FOR CARRYING THE CD PLAYER Be sure not to carry or tip the CD player with discs remaining in it. ■ Never allow metallic items (e.g. screwdrivers, tools, etc.) to come near the cassette deck’s record/playback head assembly in this unit. Doing so may not only scratch or damage the head’s mirrorsmooth finish, it may change the magnetic characteristics of the heads, causing a deterioration in reproduction performance quality. For U.K. customers If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below. Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet. ■ Although the cassette deck’s record/playback heads used in this unit are high quality heads with outstanding reproduction characteristics, they can become dirty through the use of old tapes or from dust accumulation over time. This can have a serious effect on reproduction quality. Clean the heads regularly with one of the commonly available head cleaners or with cleaning solutions. SPECIAL INSTRUCTIONS FOR U.K. MODEL IMPORTANT: The wire in the mains lead are coloured in accordance with the following code: ■ The voltage to be used must be the same as that specified on this unit. Using this product with a higher voltage than that which is specified is dangerous and may result in a fire or other type of accident causing damage. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than that which is specified. Blue: NEUTRAL Brown: LIVE ■ The sound level at a given volume setting depends on a combination of speaker efficiency, location and many other factors. Care should be taken to avoid exposure to sudden high levels of sound, which may occur when turning on the unit with the volume control setting at high, and to continuous high levels of sound. The colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug. Proceed as follows: the wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug. ■ Sudden temperature changes and storage or operation in an extremely humid environment may cause condensation inside the cabinet. Condensation can cause the unit to malfunction. Follow the procedure below to eliminate condensation. E-2 WARNING CLASS 1 LASER PRODUCT APPAREIL À LASER DE CLASSE 1 PRODUCTO LASER DE CLASE 1 To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. This compact disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior. (Europe and U.K. model only) Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. CAUTION 1 Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Laser Diode Properties Material: GaAlAs Wavelength: 780nm Emission Duration: continuous Laser Output: max. 44.6µW* * This output is the value measured at a distance of about 200mm from the objective lens surface on the Optical Pick-up Block. • • • • CAUTION 2 As the laser beam used in this compact disc player is harmful to the eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only. ACTIVE SERVO TECHNOLOGY Highamplitude bass sound Cabinet Air woofer (Helmholtz resonator) Port Active Servo Processing Amplifier Signals of low amplitude Signals Negative-impedance output drive Thus it is this problem that is resolved through the employment of a design in which the amplifier functions to supply the signals. If the electrical resistance of the voice coil is reduced to zero, the movement of the speaker unit would become linear with respect to signal voltage, and, to accomplish this, a special negative-impedance output-drive amplifier for subtracting output impedance of the amplifier is used. By employing negative-impedance drive circuits, the amplifier is able to generate precise, low-amplitude low-frequency waves with superior damping characteristics, and these waves are then radiated from the cabinet opening as highamplitude signals. The system can, therefore, by employing the negative-impedance output drive amplifier and a speaker cabinet with the Helmholtz resonator, reproduce an extremely wide range of frequencies with amazing sound quality and less distortion. The features described above are combined to be the fundamental structure of the Active Servo Technology. The theory of the Active Servo Technology is based upon two major factors, the Helmholtz resonator and negativeimpedance drive. Active Servo Processing speakers reproduce the bass frequencies through an “air woofer”, which is a small port or opening in the speaker’s cabinet. This opening is used instead of, and performs the functions of, a woofer in a conventionally designed speaker system. Thus, signals of low amplitude within the cabinet can, according to the Helmholtz resonance theory, be output from this opening as waves of great amplitude if the design is such that the size of the opening and the volume of the cabinet are in the correct proportion to satisfy a certain ratio. In order to accomplish this, moreover, the amplitudes within the cabinet must be both precise and of sufficient power because these amplitudes must overcome the “load” presented by the air that exists within the cabinet. E-3 English PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT NAMES OF CONTROLS, INDICATORS AND REAR PANEL PARTS CD Player (CDX-S50) 1 1. 2. 3. 4. 5. 2 3 4 5 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 6 7 Disc Table RESUME button OPEN/CLOSE Button: RANDOM Play Button SKIP Buttons: / (SEARCH Buttons: / ) Stop Button: Play/Pause Button: / Track Number Indicator Time Display (S, F) REPEAT Indicator RANDOM Play Indicator PROGRAM Indicator Music Calendar Indicator Music Calendar OVER Indicator Tape Side Indicator EDIT Indicator Play Indicator: For CD Player 8 9 TRACK 10 TOTAL REMAIN 11 SF RE P RAN DOM PROG HALL DIS CO CHU R CH J AZZ CLU B O N D S P O FF 1 2 3 4 5 12 Receiver (RX-S50) E DI T 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 13 OVER A B 14 15 16 17 For Receiver 18 19 18 20 21 22 PRESET HALL DIS CO CHU R CH J AZZ CLU B O N D S P O FF 23 30 MHz MEMORY 24 25 AUTO TUNING STEREO 26 31 32 33 34 27 TI M E R S LE E P 28 29 35 36 37 39 41 43 45 47 49 38 40 42 44 46 48 E-4 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. Effect Level Indicator Phones Mode Indicator Preset Number Indicator Band Indicator Station Frequency Indicator DSP ON/OFF Indicator DSP Mode Indicators MEMORY Indicator AUTO TUNING Indicator STEREO Indicator TIMER Set Indicator SLEEP Indicator 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. POWER Switch DSP ON/OFF Selector Button Remote Control Sensor DSP MODE Selector Button SP/PHONES Mode Selector Button INPUT Selector Buttons: / VOLUME Control PHONES Jack DISPLAY Button TUNER PRESET DOWN/UP Buttons A/B/C/D/E (TIMER) Button MEMORY (TIME ADJUST) Button TUNING DOWN (HOUR) Button TUNING UP (MINUTE) Button AUTO/MAN’L (SEC) Button BAND Selector Button AUTO MEMORY (TIMER REC) Button BASS Tone Control TREBLE Tone Control BALANCE Control Double Cassette Tape Deck (KXW-S70) 50 51 52 50. 51. 52. 53. 54. 55. 56. 57. 58. 59. 60. 53 54 55 67 66 56 58 57 60 61 59 63 62 65 61. 62. 63. 64. 65. 66. 67. 64 68 DECK A Cassette Compartment DECK A Select Button and Indicator DECK B Select Button and Indicator DECK B Cassette Compartment Stop Button: Play Direction Indicator ( ) DECK A EJECT Button Fast Wind Button: Play Button: Reverse Mode Switch DUBBING (NORMAL/HIGH) Buttons and Indicators REC/PAUSE Button and Indicator Dolby NR Switch Play Button: Fast Wind Button: DECK B EJECT Button Play Direction Indicator ( ) PLAY Indicator Speakers (NX-S50) 68. YST Port 69. Speaker Terminals 69 E-5 English NAMES OF CONTROLS, INDICATORS AND REAR PANEL PARTS NAMES OF CONTROLS, INDICATORS AND REAR PANEL PARTS 1 2 3 4 Rear Panel of Receiver 5 1. 2. 3. 4. 5. 6. 7. 8. 6 7 Antenna Terminals INPUT (PHONO and AUX) Terminals GND Terminal SPEAKERS Terminals VOLTAGE SELECTOR (General model only) FREQUENCY STEP Switch (General model only) System Control Sockets AC Supply Lead 8 FREQUENCY STEP switch (General model only) Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located at the rear) according to the frequency spacing in your area. Before setting this switch, disconnect the AC supply lead of this unit from the AC outlet. VOLTAGE SELECTOR (General model only) The voltage selector on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/220/240V AC, 50/60 Hz. 9 Rear Panel of Cassette Tape Deck 9. System Control Connector Rear Panel of CD Player 10. System Control Connector 10 E-6 Names of control buttons 1 TUNER DIRECT 2 3 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 A B C D E TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PLAY TAPE TIME PROG PRESET REPEAT 4 RANDOM DOWN UP PLAY STOP DECK 5 6 0 14 PHONO/AUX REC/PAUSE A/B EFFECT LEVEL - + POWER SLEEP DSP MODE SP/PHONES 13 DISPLAY VOLUME - + 12 7 8 9 10 11 E-7 ■ Receiver Control Buttons 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Remote Control Transmitter Window Preset Station Number Buttons A, B, C, D, E Selector Buttons PRESET DOWN/UP Buttons A/B/C/D/E Button EFFECT LEVEL Down (–)/Up (+) Buttons POWER Switch SLEEP Button DISPLAY Button DSP On/Off Button VOLUME Down (–)/Up (+) Buttons DSP MODE Selector Button SP/PHONES Mode Selector Button Input Selector Buttons English REMOTE CONTROL TRANSMITTER REMOTE CONTROL TRANSMITTER ■ 15. Track Number Input Buttons 16. TIME Button 17. SKIP Buttons: / (SEARCH Buttons: / ) 18. REPEAT Button 19. RANDOM Button 20. STOP Button: 21. PLAY/PAUSE Button: 22. EDIT Button 23. TAPE Button 24. PROGRAM Button 24 23 TUNER DIRECT 15 16 17 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 0 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PLAY TAPE PRESET REPEAT 18 19 RANDOM DOWN UP PLAY STOP DECK CD Player Control Buttons 22 PHONO/AUX REC/PAUSE 21 A/B EFFECT LEVEL DSP MODE SP/PHONES + - 20 25 26 27 RANDOM PLAY 25. 26. 27. 28. 29. 30. 31. TAPE PHONO/AUX A/B EFFECT LEVEL 29 PLAY REC/PAUSE DECK 28 STOP ■ Tape Deck Control Buttons - + POWER SLEEP DSP DISPLAY MODE SP/PHONES VOLUME - 31 + 30 E-8 Play Button: Stop Button: Play Button: DECK A/B Select Button Fast Wind Button: REC/PAUSE Button: Fast Wind Button: Loading the batteries for the remote control transmitter 1 1 Remove the battery compartment cover. (Press the left edge of the cover to right with a finger, and then pull it upward.) 2 Insert 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or equivalent) into the battery compartment. * Installing the batteries improperly may cause failure. 3 3 Replace the battery compartment cover. 2 • • • • Precautions for battery use Insert the batteries according to the direction indicated in the battery compartment. Replace all batteries with new ones at the same time. Remove the batteries if they are weak or if the unit is not in use for long periods. Don’t mix normal batteries with rechargeable batteries. Proper use of the remote control transmitter Aim (within the range of 60° with no obstacles) the remote control transmitter at the remote control sensor and operate as shown. Notes concerning use • Replace the batteries if control distance decreases or operation becomes unstable. • Periodically clean the transmitter window on the remote control transmitter and the sensor on the main unit with a soft cloth. • Exposing the sensor on the main unit to strong light (especially an inverter type of fluorescent lamp etc.) may interfere with operation. In this case, reposition the main unit to avoid direct lighting. • Keep the remote control transmitter away from moisture, excessive heat, shock and vibrations. • The remote control transmitter’s usable range is within 0.2m (8”) and 6m (20’) away from the sensor. Remote control sensor 0.2 m – 6 m (8” – 20’) 30° 30° E-9 English REMOTE CONTROL TRANSMITTER PREPARATION FOR USE Placing the system Placing examples RX-S50 CDX-S50 This system can be placed any way you like, however, be sure not to place another unit or any object on top of the receiver to prevent the ventilation holes on the top panel of the receiver from being obstructed. If doing so, it may damage the receiver. Notes • If the system is put in a rack, allow a space of at least 5 cm (1-15/16”) above and behind the unit. • Disconnect the AC supply lead from the AC outlet before connecting or disconnecting any component. KXW-S70 CDX-S50 RX-S50 KXW-S70 Antenna connection (1 (1) Supplied FM antenna GND Connect the FM antenna wire to the corresponding terminal and direct the FM antenna wire to the direction where the strongest signal can be received. FM ANT (2) Supplied AM (MW/LW) loop antenna AM ANT (2 (3 75Ω UNBAL. 15 m (49 feet) Connect the AM (MW/LW) loop antenna wire to the corresponding terminals. Position the AM (MW/LW) loop antenna for optimum reception. Place the AM (MW/LW) loop antenna on a shelf etc., or install it on the rack or wall with screws (not supplied). (4 Notes • When static is still heard even after adjusting the position of the AM (MW/LW) loop antenna, try reversing the connection (top to bottom). • Do not place the AM (MW/LW) loop antenna on the unit. It will result in noise generation, since the unit is equipped with digital electronics. Place the AM (MW/LW) loop antenna away from the unit. 7.5 m (25 feet) Earth rod AM ANT (3) External FM antenna Use an external FM antenna instead of an indoor FM antenna if you need better reception. Consult your dealer. GND 75Ω UNBAL. FM ANT (4) External AM (MW/LW) antenna Use an external AM (MW/LW) antenna if you need better reception. Consult your dealer. or Note When using an external AM (MW/LW) antenna, be sure to keep the wire of the AM (MW/LW) loop antenna connected. * For U.K. and Europe models, “AM” is replaced by “MW LW”. E-10 Speaker connection Connect each speaker wire to the SPEAKERS terminals. R Cautions • Do not let the bare speaker wires touch each other as this could damage the receiver and/or speakers. • When connecting the speakers to the unit, be sure to connect the speaker wires properly. Do not mistake the right channel for the left channel and the plus (+) terminal for the minus (–) terminal. • Do not connect these SPEAKERS terminals to speakers other than the provided speaker system NX-S50. L (Black wire with white line → plus (+) terminal, black wire → minus (–) terminal) System connection • • RX-S50 Connect the red connector on the rear of CDX-S50 to the red socket on the rear of RX-S50. Connect the black connector on the rear of KXW-S70 to the black socket. How to disconnect the system connector Grasp both sides of the connector to disconnect the connector. CDX-S50 KXW-S70 Connecting the AC supply lead • • To an AC outlet E-11 After connecting the speakers and system connectors, plug the AC supply lead into a convenient AC outlet. Unplug the AC supply lead from the AC outlet if the unit is not to be used for a long period of time. English PREPARATION FOR USE OPEN/CLOSE THE CONTROL DOOR When it is not necessary to operate controls inside the control door, close the door. To open or close the door, press the right edge until it clicks. TURNING THE POWER ON/OFF TO THIS SYSTEM If the AC supply lead is connected to the AC outlet, this system can be turned ON and OFF (STANDBY mode) by pressing the POWER switch on the front panel of the receiver or the POWER button on the remote control transmitter. STANDBY mode While the power is on, pressing the POWER switch (or the POWER switch on the remote control transmitter) switches the system to the STANDBY mode. (In this mode, the display shows only the time.) In this mode, main voltage is still present inside the system. If you want to switch off the system completely, disconnect the AC power plug from the AC outlet. RANDOM PLAY DECK STOP PLAY TAPE PHONO/AUX REC/PAUSE A/B EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE SP/PHONES VOLUME - + E-12 1 1 While the power is on, press the DISPLAY button to display the time. If the power is off, you can proceed to the next step. 2 While pressing the TIME ADJUST button, press the HOUR button and set the hour. * Press the HOUR button once to advance the time by 1 hour. Press and hold to advance continuously. 3 While pressing the TIME ADJUST button, press the MINUTE button and set the desired time. * Press the MINUTE button once to advance the time by 1 minute. Press and hold to advance continuously. * The hour setting will not advance even if the minute advance from “59” to “00”. DISPLAY 2 MEMORY TUNING DOWN UP TIME ADJ HOUR MINUTE Changes. 3 MEMORY TUNING DOWN UP TIME ADJ HOUR To display the time by “second” While pressing the SEC button, the current time is displayed by minute and second. To reset the second to “00” While pressing the SEC button, press the TIME ADJUST button. * If the current second is lower than 30, it is reset to 00. * If the current second is higher than 30, the minute is advanced by 1 minute and the second is reset to 00. (If the current minute is “59”, in this case, the hour is also advanced by 1 hour.) MINUTE Changes. In the event of a power failure or when the AC supply lead is disconnected. The time display will go out, however, the clock will function for about 30 minutes without power supply. So you do not have to reset the time if the AC power supply is resumed within about 30 minutes. When the AC power supply is resumed after more than 30 minutes pass without power supply, the time display will flash on and off to indicate that the time must be reset. Note If this system is left for several minutes without setting the time after the AC power lead of this system is connected to the AC outlet, there may be a case that the display is turned into a demonstration mode. (This mode is virtually unnecessary for using this system.) In this case, first turn the power on by pressing the POWER switch to cancel the mode, and then set the time. E-13 English SETTING THE CLOCK SOUND CONTROL Volume Front panel operation Rotate the VOLUME control towards 10 to increase the volume, and towards 0 to decrease the volume. VOLUME Remote control operation Press the VOLUME + button to increase the volume and the VOLUME – button to decrease the volume. VOLUME - 0 + I0 Balance Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused from the speaker settings or the listening room condition. Turn this clockwise to emphasize the right and counterclockwise for the left. BALANCE L R Tone BASS BASS TREBLE TREBLE – + – : Turn this clockwise to increase (or counterclockwise to decrease) the low frequency response. : Turn this clockwise to increase (or counterclockwise to decrease) the high frequency response. + DIGITAL SOUND FIELD PROCESSOR (DSP) CONTROL The Digital Sound Field Processor (DSP) built into this unit presents you with the ambience of an actual concert hall, jazz club, etc. by adding effects as sonic reflections or reberverations that create the sound environment of a hall etc. HALL This unit provides the following 4 DSP modes that simulates actual sound environments. Mode DISCO HALL This mode is suitable for reproducing live recordings of pop or rock music including vocals. You can obtain sound expansion and reverberations of a hall by this mode. DISCO You can enjoy an atmosphere of disco with lively bass and powerful sound field. MODE CHURCH CHURCH JAZZ CLUB JAZZ CLUB E-14 Feature This mode creates a rich sound field of church with long reverberations. It is suitable for vocals etc. This mode creates a sound field with much presence adding spatial effect as if music instruments are coming in front. Listening to the music with the DSP Phones mode indicator Receiver HALL 1 Press the DSP ON/OFF switch so that “ON DSP” illuminates on the display. 2 Select a desired DSP mode by pressing the DSP MODE selector button once or more until the name of the mode appears on the display. 3 Playback a source. (For source playback, refer to other sections described later.) 4 Adjust the level of effects by pressing the EFFECT LEVEL down (–) or up (+) button. * Effect level can be checked with the effect level indicator on the display. ON DSP Receiver If you will not use the DSP Press the DSP ON/OFF switch so that “DSP OFF” illuminates on the display. 1 2 When listening with headphones Press the SP/PHONES mode button so that the phones mode indicator is illuminated on the display. You can obtain a DSP effect suitadle for the headphone listening. If not using headphones, the SP/PHONES mode button should be set so that the phones mode indicator is not illuminated on the display. TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 0 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PRESET REPEAT DOWN RANDOM PLAY DECK STOP PLAY TAPE PHONO/AUX REC/PAUSE A/B 4 EFFECT LEVEL - + POWER SLEEP 1 UP DSP DISPLAY MODE 2 Note SP/PHONES DSP effect is also recorded along with a source. If you wish to record a source without DSP effect, turn the DSP off when recording. VOLUME - + COMPACT DISC PLAYER OPERATION Care of compact discs Compact discs are fairly resistant to damage, however mistracking can occur due to an accumulation of dirt on the disc surface. Follow the guidelines below for maximum enjoyment from your CD collection and player. • Do not write on either side of the disc, particularly the nonlabel side. Signals are read from the non-label side. Do not mark this surface. • Keep your discs away from direct sunlight, heat and excessive moisture. • Always hold the CDs by the edges. Fingerprints, dirt or water on the CDs can cause noise or mistracking. If a CD is dirty or does not play properly, clean it with a soft, dry cloth, wiping straight out from the center, along the radius. E-15 English DIGITAL SOUND FIELD PROCESSOR (DSP) CONTROL COMPACT DISC PLAYER OPERATION CD playback 1 Receiver 1 Select the CD player so that “CD” appears on the display by pressing the INPUT selector or button. 2 3 Press the OPEN/CLOSE button to open the disc table. 4 Press the OPEN/CLOSE button to close the disc table. * The total number of tracks and the total playing time of the disc will be displayed for several seconds. * The music calendar will be displayed only for the number of tracks on the disc. * If the compact disc contains more than 21 tracks, the “OVER” indicator will light up on the music calendar. POWER 2, 4 CD Player Place a disc on the table, label side up. * 8 cm (3”) disc can be played without an adaptor. Total number of tracks TRACK TOTAL HALL 5, 1, 2 ON DSP 1 2 3 4 5 6 7 8 9 10 11 12 Music calendar 3 5 Total playing time Press the play/pause button to start playback from track 1. * The “ ” indicator will appear and playback will begin. As the playback of each track on the music calendar is finished, that track number will go out. To interrupt playback 1 Press the play/pause button. * The “ ” indicator will flash. 2 Press the play/pause button to resume playback from the same point. TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PRESET REPEAT RANDOM DOWN UP PLAY STOP DECK PLAY 0 TAPE 5, 1, 2 To stop playback Press the stop 1 To switch the unit off after use PHONO/AUX REC/PAUSE Turn the unit off by pressing the POWER switch. (The indicators will go off except for the current time display.) A/B EFFECT LEVEL POWER - + POWER SLEEP DSP DISPLAY MODE SP/PHONES VOLUME - button. + E-16 Direct operation Even when an input source other than CD player is selected, pressing the play/pause button, a track number input button or the RANDOM play button, or pressing the front edge of the disc table gently will start playback directly. In this case, if the tape deck is playing back a tape, it will be stopped automatically. * These ways of playback can also be used to close the disc table. If the table is closed in these ways, playback will begin automatically, however, the display will not show the total number of tracks and the total playing time of the disc. Precautions • If TV or radio interference occurs during CD player operation, move the unit away from the TV or radio. • Subjecting the unit to shock or vibration can cause mistracking. • Playing some compact discs at high volume can cause mistracking. In this case, listen at lower volume. • Do not push the disc table while it is moving. • If the power fails while the table is open, wait until the power supply returns or gently push the table manually to close it. • The temperature range for playing compact discs is recommended to be 5°C (41°F) – 35°C (95°F). Direct-selection play By using the track number input buttons on the remote control transmitter, any track you wish to listen to can be played directly. TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 0 Use the track number input buttons to select the desired track number. Play will begin automatically. TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 A B C D E TIME PROG TAPE EDIT 9 +I0 0 STOP PLAY/PAUSE CD A. For example, to choose selection 5 Press the “5” button. E PRESET REPEAT RANDOM DOWN UP PLAY STOP DECK A/B/C/D/E TUNER PLAY TAPE +I0 B. For example, to choose selection 12 (1) Press the “+10” button. (2) Within 3 seconds, press “2” button. PHONO/AUX REC/PAUSE A/B EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE SP/PHONES VOLUME - + C. For example, to choose selection 20 (1) Press the “+10” button. (2) Within 3 seconds, press the “+10” button again. (3) Within 3 seconds, press the “0” button. Note A track number higher than the number of tracks on the disc cannot be selected. Also, if a higher track number is selected while the disc table is open, play will begin from the last track on the disc when the disc table is closed. E-17 English COMPACT DISC PLAYER OPERATION COMPACT DISC PLAYER OPERATION “Skip search” and “Manual search” are performed using the same buttons. Skip search 1 The beginning of any track can be found automatically. CD Player 1 2 2 Load a disc and begin playback. Press the button to advance or button to reverse through the disc. Press once for each track to be advanced or reversed. once to advance to the track following the • Press one now playing back. once to return to the start of the track now • Press playing back. twice to return to the track before the track • Press now playing back. Notes • This function can also be performed while the unit is stopped. Press the play/pause button when your desired track number appears in the track number display. Playback will begin from the beginning of the track. • This function will be performed forward or backward from any point on the disc. However, it will not move forward during playback of the final track. TUNER DIRECT 2 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 B C D E PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PRESET REPEAT RANDOM DOWN UP PLAY STOP DECK PLAY Manual search 0 A TIME TAPE 1 2 1 PHONO/AUX REC/PAUSE A/B EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE SP/PHONES VOLUME - + Begin playback. Press and hold the button to advance play rapidly, and the button to reverse play rapidly. * The sound can be heard (although slightly garbled) during manual search in either direction. This is convenient for reviewing the contents quickly. Note Manual search can also be performed while playback is paused, though no sound will be heard. E-18 Program play 6 1 You can program up to 20 tracks in any desired order. CD Player 1 2 Load a disc and close the disc table. 3 Use the track number input buttons to select the desired track number. * The selected track number and the total play time of the programmed tracks will illuminate on the display, and soon it is replaced by the display of the next playback order. Programmed track numbers will stop flashing and illuminate on the music calendar. * Pressing the TIME button displays the total play time of the programmed tracks for about 1 second, and then it is replaced by the display of the next playback order. When in the stop mode, press the PROGRAM button to prepare for programming. * “PROG” and “P-01” illuminate on the display, and all track numbers on the disc begin flashing. TUNER DIRECT 2 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 0 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PLAY TAPE PRESET REPEAT RANDOM DOWN UP PLAY STOP DECK * For example, to choose selection 12 (1) Press the “+10” button. (2) Press the “2” button. 3 5 - + POWER SLEEP DSP Repeat step 3 for any other track. Up to 20 tracks can be programmed. 5 Press the play/pause button to start playback of programmed tracks. PHONO/AUX REC/PAUSE A/B EFFECT LEVEL 4 MODE DISPLAY SP/PHONES VOLUME - + Notes It is also possible to program a sequence of tracks while looking at the list of tracks on the surface of the disc before closing the disc table. • During playback or pause, programming is not possible. • If the total time of the programmed tracks reaches 100 minutes or more, only the last two-digits will be displayed for the three-digit number. • The total time of the programmed tracks will not be displayed, if a track number higher than 19 is programmed. • Skip search can be performed during playing back, but only within the range of the programmed tracks. • Manual search can be performed during playing back to search through all tracks, including unprogrammed tracks. • Display information during programming TRACK PR OG HA L L ON DSP 1 2 3 4 5 6 7 8 9 10 11 12 Playback order Selected track number Selected disc Total playing time TRACK TOTAL PR OG HA L L ON DSP 1 2 3 4 5 6 7 8 9 10 11 12 Music calendar E-19 English COMPACT DISC PLAYER OPERATION COMPACT DISC PLAYER OPERATION To stop program play • • / CD Player Press the stop button. The first track number programmed will be displayed. To resume playback, press the play/pause / button. Playback will begin from the beginning of the program. To cancel a programmed sequence There are several methods as described below. • Press the stop button while the unit is stopped. • Open the disc table • Switch off the power. To check program data PROG 1. If during playing back, press the stop button. 2. Press the PROG button. 3. Each time the SKIP button is pressed, the track numbers and sequential order of the programmed tracks can be checked one after another. The display of the track number can be returned (sequentially in reverse order) by pressing the SKIP button. TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 B C D E PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PRESET REPEAT DOWN RANDOM PLAY DECK To correct program data 0 A TIME 1. Follow the procedure described in “To check program data”. 2. Display the track number to be corrected by pressing the SKIP button. 3. Press a track number input button to select a track to replace the one displayed. The previously programmed track will be cleared from the memory and the new one will be programmed. 4. After the correction has been completed, press the PROG button or play/pause / button once again. UP STOP PLAY TAPE PHONO/AUX REC/PAUSE / A/B EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE SP/PHONES VOLUME - + E-20 Repeat play An entire disc, a single track or a programmed sequence can be continuously repeated. CD Player 1 While watching the display, press the REPEAT button once or more to select a desired repeat play mode (S REP or F REP). 2 Press the play/pause button. Repeat play modes 2 SINGLE REPEAT (S REP) A single track is played back repeatedly. * This is also available in the program play mode and the random play mode. (If the repeat play mode is switched off, the program play mode or the random play mode will be resumed.) FULL REPEAT (F REP) An entire disc is played back repeatedly. * In the random play mode, the disc is repeatedly played back, but the order of tracks is different every time. TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 0 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PLAY TAPE PRESET REPEAT 1 9 RANDOM DOWN UP PLAY STOP DECK To cancel the repeat play PHONO/AUX REC/PAUSE Press the REPEAT button once or more so that the (S, F) REP indicator goes out. 2 A/B EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE - off S REP SP/PHONES VOLUME + F REP E-21 English COMPACT DISC PLAYER OPERATION COMPACT DISC PLAYER OPERATION Random play CD Player The tracks on the disc can be played back in a random order. 1 2 Load a disc and close the disc table. Press the RANDOM button to begin random play. * The “RANDOM” indicator will light up. To cancel the random play Press the stop 2 1 button. The “RANDOM” indicator goes out. Note This feature will not function during programming, or during program play. TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 0 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PRESET REPEAT 2 9 RANDOM DOWN UP PLAY STOP DECK PLAY TAPE PHONO/AUX REC/PAUSE A/B EFFECT LEVEL - + POWER SLEEP DSP MODE DISPLAY SP/PHONES VOLUME - + Switching the time display TIME ➀ Each time the TIME button is pressed, the display will change as described below. TRACK HALL [Example] When the second track is being played back (Refer to the illustration on the left.) ON D S P 2 3 4 5 6 7 8 9 10 11 12 TUNER DIRECT 1 1 6 2 3 2 3 7 4 5 4 5 8 6 7 8 9 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PLAY TAPE PRESET REPEAT RANDOM DOWN UP PLAY STOP DECK 0 PHONO/AUX REC/PAUSE ➁ TRACK EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE 3 4 5 6 7 8 9 10 11 12 SP/PHONES VOLUME - be displayed. * 8 seconds have passed since the beginning of the second track. ➁ The remaining play time for the current track will be displayed. * 2 minutes and 58 seconds remain till the end of the second track. ➂ The total play time of the disc will be displayed. (If the unit is in the program play mode, the total play time of the programmed tracks will be displayed.) ➃ The total remaining play time from the point being played at that time will be displayed. * 41 minutes remain till the end of the disc. ON D S P 2 A/B ➀ The elapsed play time for the track now playing back will REMAIN HALL + ➂ TRACK TOTAL HALL ON D S P 2 3 4 5 6 7 8 9 10 11 12 ➃ TRACK TOTAL REMAIN HALL ON D S P 2 3 4 5 6 7 8 9 10 11 12 Notes During random play, the total remaining play time on the disc will not be displayed. The total remaining play time will not be displayed for track number 20 or higher. • • E-22 Normally, if station signals are strong and there is no interference, quick automatic-search tuning (Automatic tuning) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (Manual tuning). Automatic tuning 1 Receiver 4, 3 3, 2 1 Select the tuner so that “TUNER” appears on the display by pressing the INPUT selector or button. 2 Select the reception band [FM or AM (MW or LW)] by pressing the BAND button while watching the display. 3 Press the AUTO/MAN’L button so that “AUTO TUNING” appears on the display. (In this mode, stations are received in stereo or monaural automatically.) 4 Press the TUNING UP button to tune to a higher frequency, or press the TUNING DOWN button to tune to a lower frequency. 5 If the station where tuning search stopped is not the desired one, follow step 4 again. * If the tuning search does not stop at the desired station, change to the Manual tuning method as described below. STEREO indicator will illuminate when an FM stereo broadcast with sufficient signal strength is received. 2 * Manual tuning “AM” is for Australia and General models. “MW/LW” is for U.K. and Europe models. 1 2 Follow steps 1 and 2 of the Automatic tuning method. 3 Press and hold the TUNING UP button to tune to a higher frequency, or press and hold the TUNING DOWN button to tune to a lower frequency. Release it just before reaching the desired frequency, and then press it repeatedly until the desired frequency appears. Press the AUTO/MAN’L button so that “AUTO TUNING” disappears from the display. (In this mode, stations are received in monaural.) Note If you tune to an FM station manually, it is received in monaural automatically to increase the signal quality. E-23 English TUNING OPERATION TUNING OPERATION Preset tuning This unit can store station frequencies selected by tuning operation. With this function, you can select any desired station by only calling the corresponding preset station number. Up to 40 stations (8 stations x 5 areas) can be stored. To store stations 4, 2 (Example: To store a station to A1) Receiver 3, 1 2, 5 1 Tune to a desired station. (Refer to the previous page for tuning procedure.) 2 Press the MEMORY button. * The MEMORY indicator will flash for about 5 seconds. 3 Select a desired area (A – E) by pressing the A/B/C/D/E button while watching the display, before the MEMORY indicator goes out. (In this case, select area A) 4 Select a preset station number by pressing the TUNER PRESET DOWN or UP button repeatedly before the MEMORY indicator goes out. (In this case, select “1”.) 5 Within about 5 seconds, press the MEMORY button again. 4, 2 PRESET HALL MHz ON DSP Shows the displayed station has been programmed to A1. TUNER DIRECT 3, 1 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 0 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PRESET REPEAT 4, 2 9 RANDOM DOWN UP PLAY STOP DECK PLAY TAPE A/B - + POWER SLEEP DSP DISPLAY * In the same way, program other stations to A2, A3 ... A8. * You can program more stations to the preset station numbers on other areas in the same way by selecting other areas in step 2. PHONO/AUX REC/PAUSE EFFECT LEVEL AUTO TUNING STEREO MODE SP/PHONES 3, 1 To recall a preset station VOLUME - + 1 Select the area of preset station numbers by pressing the A/B/C/D/E button. 2 Select the desired preset station number by pressing the TUNER PRESET DOWN or UP button repeatedly. Notes • A new setting can be programmed in place of the former one. • For presets the setting of the AUTO/MAN’L button is stored along with the station frequency. For easier operation By using the preset station number buttons and the A,B,C,D,E selector buttons on the remote control transmitter, a preset station number and an area can be selected directly. E-24 Automatic preset tuning You can also make use of an automatic preset tuning function. By this function, this unit performs automatic tuning and stores stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on the previous page. 1 Receiver 1 Select the tuner so that “TUNER” appears on the display by pressing the INPUT selector or button. 2 Press and hold the AUTO MEMORY button for about 2 seconds. * The MEMORY and AUTO TUNING indicators will flash. This unit performs automatic tuning and received stations are programmed to A1, A2 ... A8 sequentially. After the automatic preset tuning is completed The display shows the frequencies of the first preset station (stored to A1). Check the contents and the number of preset stations by following the procedure of the section “To recall a preset station” on the previous page. 2 To recall a preset station Simply follow the procedure of the section “To recall a preset station” on the previous page. Notes • The automatic preset tuning search will be performed through all frequencies until 40 stations are stored. If the number of received stations is less than 40, the search will stop after searching through all frequencies. • With this function, only stations with sufficient signal strength are stored automatically. If the station you want to program is weak in signal strength, tune to it in monaural manually and program it by following the procedure of the section “To store stations” on the previous page. • You can replace a preset station by another FM or AM (MW or LW) station manually by simply following the procedure of the section “To store stations” on the previous page. Fundamental rules of internal automatic preset tuning operation Basically, FM stations are programmed onto area A, B and C, and AM stations are programmed onto area D and E (MW stations are onto D and LW stations are onto E) in that order automatically. * If, for example, the number of received FM stations is not enough to fill up three areas (A, B and C), AM (MW or LW) stations are programmed closely from the preceeding empty areas. In such a case, AM (MW) stations are programmed from area B or C (and LW stations are from area C or D.) * Moreover, one area is programmed with stations of the same band only. If, for example, the last FM station is programmed to B4, B5–B8 will be programmed with no station, and AM (MW) stations are programmed from area C. Memory back-up The memory back-up circuit prevents the programmed data from being lost even if the AC supply lead is disconnected from the AC outlet or the power is cut due to temporary power failure. If, however, the power is cut for more than one week, the memory may be erased. If so, it can be reprogrammed by simply following the Preset tuning steps. E-25 English TUNING OPERATION TAPE DECK OPERATION General information • • • • • • • • Detection hole Tab E-26 Do not use C-120 tapes, tapes with internal reels or poorquality tapes, since they can cause malfunctions. Before loading a tape into the cassette compartment, tighten the slack tape with a pen or pencil. Tapes have removable tabs which prevent accidental recording or erasing from taking place. Removing the tab on the top left protects the side facing you from erasure. Cover the tab holes with adhesive tape to erase or record again. This deck is a Double Cassette Deck with Automatic Reverse Function. DECK A: Playback only. DECK B: Playback or recording. This deck features an auto tape selector. Just load the tape, and the tape formula being used will be sensed automatically. This unit can play back metal tapes as well as normal or chrome tapes, and recording can also be done on metal tapes. When covering erasure prevention tab holes, do not cover the chrome and metal detection holes. Otherwise, the deck will treat tape as normal tape. Do not press the EJECT button during playback or recording. Tape A or tape B playback 1 Receiver 1 Select the tape deck so that “TAPE” appears on the display by pressing the INPUT selector or button. 2 Open the DECK A or DECK B cassette compartment by pressing the EJECT button. 3 Load the tape into the DECK A or DECK B cassette compartment, and close the lid panel completely by pressing the upper part of the center of the panel as figured left. * If you loaded two tapes into both the DECK A and B cassette compartments, select the DECK A or B in which the tape to be played back is loaded by pressing the DECK A or B select button. 4 Set the Dolby NR switch to B or C if the tape has been recorded with Dolby noise reduction, and to OFF if Dolby NR was not used. * For selection of the Dolby B or C position, refer to the “Dolby B and C Type Noise Reduction” on page 29. 5 Set the reverse mode switch as desired. DECK A select button DECK B select button Tape Deck The reverse mode switch can be operated before or during playback, and changes tape playback as follows: 2 56 64 Side A only Side A → Side B Side A → Side B Continuous play (8 times) Side B only Side B only Side B → Side A Continuous play (8 times) 2 6 3 Press the play button to listen to side A, or the play button for side B. To stop playback Press the stop button. Note When removing the tape, press the stop then open the cassette compartment. button, and Direct operation Even if an input source other than tape deck is selected, pressing the play button (or the fast wind button) will start playback (or fast winding) directly. E-27 English TAPE DECK OPERATION TAPE DECK OPERATION Winding the tape Tape Deck 1 2 If during playback, first press the stop 3 Press the stop Next press the fast wind wind the tape. or fast wind button. button to button to stop. * While winding the tape, the corresponding play direction indicator flashes rapidly. Note When the tape is wound to the end, this unit will then function as described below, according to the setting of the reverse mode switch. : The tape stops at the end. : If the winding direction is , when the tape reaches the end, playback automatically starts from the reverse side. If the winding direction is , the tape stops at the end. : When the tape reaches the end, playback automatically starts from the reverse side. Searching for the beginning of a desired selection Carry out the following operation during playback to find the beginning of a desired selection on the tape. TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PRESET REPEAT RANDOM DOWN UP PLAY STOP DECK 9 PLAY 0 To listen to the same selection Press the button if the direction of the current playback is . Press the button if the direction of the current playback is . TAPE PHONO/AUX REC/PAUSE A/B EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE SP/PHONES To listen to the next selection Press the button if the direction of the current playback is . Press the button if the direction of the current playback is . VOLUME - + * While searching, the corresponding play direction indicator flashes slowly. Notes • This function may not work for tapes with * Material with long pauses or quiet passages. * Low recording levels or excessive noise. * Pauses of less than 4 seconds between selections. • If searching is carried out at the first or the last part of a selection, the searching may not function correctly. E-28 English TAPE DECK OPERATION Continuous playback 3 Tape Deck 1 Load the tapes into the DECK A and DECK B cassette compartments. 2 Set the reverse mode switch to . The reverse mode switch can be operated before or during playback, and changes tape playback as follows: 1 24 4 1 <DECK A> <DECK A> Tape A Side A → B → Tape B Side A → B Continuous play (8 times) Tape A Side B → Tape B Side A → B → Tape A Side A Continuous play (8 times) TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 0 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PLAY TAPE PRESET REPEAT RANDOM DOWN UP PLAY STOP Press the DECK A or B select button to select the tape to be played back first. 4 Press the play button to listen to side A, or the play button for side B. PHONO/AUX REC/PAUSE DECK 4 3 A/B 4 EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE SP/PHONES VOLUME - + 3 Dolby B and C Type Noise Reduction • DOLBY B.C NR With cassette tapes, the most noticeable form of noise is high frequency hiss. To reduce this hiss noise, this unit has been equipped with a newly developed Dolby C noise reduction system in addition to its conventional Dolby B NR. Either type of noise reduction may be selected with the switch provided. Dolby B NR has a noise reduction effect of about 10 dB in the high frequency range. The corresponding figure with Dolby C NR is about 20 dB, but this is over the entire range where the human ear is most sensitive to noise (2 kHz to 8 kHz). Also, Dolby C NR has the same noise reduction effect at both high and low signal levels. In addition, Dolby C NR improves the tape’s MOL (Maximum Output Level). Dolby noise reduction is a 2 part process that acts both on recording and playback; be sure that the noise reduction button is set to the same position on record and play. * Noise in the source material cannot be reduced with the Dolby NR system. Dolby and the double D mark are trademarks of Dolby Laboratories Licensing Corp. Dolby noise reduction system manufactured under license from Dolby Laboratories Licensing Corp. E-29 RECORDING A COMPACT DISC • Receiver • • • 1 When recording important selections, be sure to make a preliminary test to ensure that the desired source material is being properly recorded with good sound quality. The automatic recording level control circuit automatically controls the level of the input signal used for recording. Adjusting the VOLUME, BALANCE, TREBLE and BASS controls have no effect on the recorded sound. If, however, the DSP is on, the DSP effect is recorded along with the source. * Music with DSP effect is suitable for listening to inside a car etc. For the tape deck, the deck which can be used for recording is the DECK B only. When recording, be sure to load a tape into the DECK B cassette compartment. CD synchronized recording CD Player 6 Tape Deck 1 Select the CD player so that “CD” appears on the display by pressing the INPUT selector or button, and load the disc to be recorded. 2 Load a tape into the DECK B cassette compartment. * Wind past the beginning part of the tape on which recording can not be performed. 3 When recording with the Dolby NR system, set the Dolby NR switch to B or C; if not, set it to OFF. * For selection of the Dolby B or C position, refer to the “Dolby B and C Type Noise Reduction” on page 29. 4 Set the reverse mode switch as desired. When the tape is set so that side A faces you, recording will be done as follows automatically according to the selected reverse mode. 4 5 3 2 Side A only Side A → Side B Side A → Side B Side B only Side B only Side B only TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PRESET REPEAT 5 DOWN RANDOM PLAY DECK 0 6 5 Press the REC/PAUSE button. * The corresponding indicator will light up and the play direction indicators flash. 1 6 Start CD playback by pressing the play/pause button. * Before CD playback begins, recording automatically begins on the side of the tape now selected. UP STOP PLAY TAPE PHONO/AUX REC/PAUSE A/B EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE SP/PHONES VOLUME - + E-30 To stop recording temporarily 1 2 / CD Player Press the stop button of the CD player. Choose the selection to be recorded next by using the SKIP or button, and then press the play button of the CD player to resume recording (or simply press the track number input button on the remote control transmitter). To stop recording Press the stop button of the tape deck. (At this time, CD playback does not stop.) Recording programmed tracks Programmed tracks can also be recorded in the same way. Tape Deck 1 Program desired tracks. (Refer to page 19 for the programming procedure.) 2 3 Follow steps 2–5 on the previous page. Press the play/pause / button of the CD player. Notes • During CD Synchronized Recording, when more than 4 seconds elapse between tracks, the tape will stop automatically and resume recording when the beginning of the next track is found. • The CD Synchronized Recording will function even when the CD player is turned into random play mode. TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 0 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PRESET REPEAT RANDOM DOWN UP PLAY STOP DECK PLAY TAPE PHONO/AUX REC/PAUSE A/B EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE SP/PHONES VOLUME - + / E-31 English RECORDING A COMPACT DISC RECORDING A COMPACT DISC Recording CD on both sides of a tape automatically Receiver 1 Select the CD player so that “CD” appears on the display by pressing the INPUT selector or button, and load the disc to be recorded. 2 3 Load a tape into the cassette compartment. 4 5 Set the reverse mode switch to 1 CD Player 1 Tape Deck When recording with the Dolby NR system, set the Dolby NR switch to B or C; if not, set it to OFF. * For selection of the Dolby B or C position, refer to the “Dolby B and C Type Noise Reduction” on page 29. or . Press the EDIT button. (“EDIT” appears on the display.) CD playback and recording starts. Recording is carried out on side A and B of the tape continuously. * If the tape has not rewound to the end, it is rewound to the end rapidly before recording starts. Recording starts from the first part of the tape on which recording can be done. * “A ” (or “ B”) on the display shows the side of the tape on which recording is being carried out. * When the recording on side A finishes while a track is being played back, the sound is automatically faded out, and then the recording stops. The recording on side B starts from the beginning of the same track. Note The CD player’s repeat play mode will be canceled during this recording mode. Recording programmed tracks Programmed tracks can also be recorded in the same way. 4 3 2 1 Program desired tracks. (Refer to page 19 for the programming procedure.) 2 Follow steps 2–5 described above. To cancel this function Before recording, press the stop or the tape deck. button of the CD player To stop recording Press the stop button of the tape deck. (At this time, CD playback automatically stops.) TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 0 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PRESET REPEAT RANDOM DOWN UP PLAY STOP DECK PLAY TAPE 5 1 PHONO/AUX REC/PAUSE A/B EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE SP/PHONES VOLUME - + E-32 English RECORDING A COMPACT DISC Automatic tape-editing This convenient feature can be used to program tracks on a disc for recording to tape. By only memorizing the tape’s total possible recording time, the unit will automatically program tracks or help you to program tracks so they will fit onto the tape with the least amount of unrecorded space remaining at each end of the tape. Receiver To record a disc with the order of tracks unchanged 1 CD Player 1 Select the CD player so that “CD” appears on the display by pressing the INPUT selector or button, and load the disc to be recorded. 2 3 Load a tape into the cassette compartment. 4 5 Set the reverse mode switch to 1 When recording with the Dolby NR system, set the Dolby NR switch to B or C; if not, set it to OFF. * For selection of the Dolby B or C position, refer to the “Dolby B and C Type Noise Reduction” on page 29. . Press the TAPE button to select the length of the tape to be used. Whenever pressed, C-46, C-54, C-60 and C-90 appear on the display in turn, and next it returns to the normal display mode. → off Tape Deck or → C-46 → C-54 → C-60 → C-90 When using tapes other than C-46, C-54, C-60 or C-90 When C-46, C-54, C-60 or C-90 is appearing on the display, input the tape length by using the track number input buttons on the remote control transmitter (Examples) C-62: Press “6” and then “2”. C-30: Press “3” and then “0”, or press “+10” three times and then “0”. 4 3 2 6 1)Tracks on the disc are automatically divided between side A and side B. You can check the process by watching the display. 2)The end part of the tape on which recording cannot be done is wound. 3)This unit starts searching for a peak level through all tracks to be recorded. (While searching, “LEVEL” flashes on the display.) When searching is finished, this unit adjusts the recording level properly on the basis of this data. 4)CD playback and recording starts. Recording is carried out on both side A and B of the tape. TUNER DIRECT 5 6 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 0 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PRESET REPEAT DOWN RANDOM PLAY DECK UP STOP PLAY TAPE 5 1 PHONO/AUX REC/PAUSE A/B EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE SP/PHONES VOLUME - Press the EDIT button. (“EDIT” appears on the display.) The following internal operations are carried out before recording is automatically started. + E-33 RECORDING A COMPACT DISC Note The CD player’s repeat play mode will be canceled during this recording mode. CD player To cancel tape-editing function Before recording, press the stop or the tape deck. button of the CD player To stop recording Press the stop button of the tape deck. (At this time, CD playback automatically stops.) To make this unit program tracks on a disc automatically so that the least amount of unrecorded space remains on the tape 1 2 3 Tape Deck Follow steps 1–5 on the previous page. Press the PROGRAM button. Press the TAPE button. “AP A> ” illuminates during programming for side A, and “AP B> ” illuminates during programming for side B. * After “AP B> ” goes out from the display, you can check the programmed contents for side A and B respectively. To check, cancel or correct program data, refer to page 20. 4 2 3 TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 6 7 8 7 8 9 0 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PRESET REPEAT RANDOM DOWN UP PLAY STOP DECK PLAY TAPE 4 PHONO/AUX REC/PAUSE A/B EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE SP/PHONES VOLUME - + E-34 Press the EDIT button. (“EDIT” appears on the display.) The recording is automatically started. * The unit searches for a peak level on each track to adjust the recording level properly. The search is carried out before recording each track. (While searching, “LEVEL” flashes on the display, and recording is paused.) To record programmed tracks Receiver 1 CD Player 1 Select the CD player so that “CD” appears on the display by pressing the INPUT selector or button, and load the disc to be recorded., and load a disc on the disc table. 2 3 Follow steps 2–5 on page 33. 4 Use the track number input buttons to select the desired track number. 5 Repeat step 4 to set more programs for the side A of the tape. You can select the same track again. * Pressing the TIME button displays the total remaining time on the side of the tape for about 1 second, and then it is replaced by the display of the next playback order. * If “ERR” appears on the display, the track number just selected cannot be programmed because there is not enough time remaining on the side A of the tape. However, at this time, if any other track number is flashing continuously on the display, you can program it instead of the unprogrammable one. 6 After you finish the programming for the side A, press the TAPE button. * “Pu” appears on the display, then you can begin programming for side B. 7 Repeat step 4 to set more programs for the side B of the tape. You can select the same track again. * If “ERR” appears on the display, the track number just selected cannot be programmed because there is not enough time remaining on the side B of the tape. However, at this time, if any other track number is flashing continuously on the display, you can program it instead of the unprogrammable one. 8 Press the EDIT button. (“EDIT” appears on the display.) The recording is automatically started. * The unit searches for a peak level on each track to adjust the recording level properly. The search is carried out before recording each track. (While searching, “LEVEL” flashes on the display, and recording is paused.) 1 TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 0 A B C D E TIME PROG 3 6 EDIT STOP PLAY/PAUSE CD A/B/C/D/E TUNER DOWN RANDOM PLAY DECK +I0 TAPE PRESET REPEAT 4 1 UP STOP PLAY TAPE PHONO/AUX REC/PAUSE A/B EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE SP/PHONES VOLUME - + 8 Display information during programming Next playback order TRACK PR OG HA L L Press the PROGRAM button. * “PROG” and “P-01” illuminate on the display, and all track numbers on the disc begin flashing. ON DSP 1 2 3 4 5 6 7 8 9 10 11 12 A Notes on tape-editing • To check, cancel or correct program data, refer to page 20. • The maximum number of tracks that can be programmed is 20. • This function can be used to program up to track number 20. If the disc has more than 20 tracks, track number 20 and thereafter will not be programmed. Side of the tape Selected track number TRACK Total remaining time on the side of the tape REMAIN PR OG HA L L ON DSP 1 2 3 4 5 6 7 8 9 10 11 12 A Programmed track numbers illuminate and unprogrammed ones flash. E-35 English RECORDING A COMPACT DISC OTHER RECORDINGS Recording from the built-in tuner 1 Select the tuner so that “TUNER” appears on the display by pressing the INPUT selector or button. 2 Tune to the desired station. (Refer to the “TUNING OPERATION” on pages 23 and 24.) 3 4 Load a tape into the cassette compartment. 5 Set the reverse mode switch to to record on only one side, or to (or ) for continuous recording on both sides. 6 Press the REC/PAUSE button. * The corresponding indicator lights up and the play direction indicators flash. 7 Press the play button to record on side A, or the play button to record on side B. * For continuous recording on both sides, begin on side A. Recording stops automatically at the end of side B. Receiver 1 Tape Deck 5 4 6, 1 7, 2 3 7, 2 When recording with the Dolby NR system, set the Dolby NR switch to B or C; if not, set it to OFF. * For selection of the Dolby B or C position, refer to the “Dolby B and C Type Noise Reduction” on page 29. To stop recording temporarily 1 2 Press the REC/PAUSE button. To resume recording, press the play button whose indicator is flashing. To stop recording Press the stop TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 0 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PLAY TAPE PRESET REPEAT RANDOM 7, 2 9 DOWN UP PLAY STOP DECK 1 PHONO/AUX REC/PAUSE A/B EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE SP/PHONES VOLUME - + 7, 2 6, 1 E-36 button. English OTHER RECORDINGS Dubbing • Receiver • 1, 2 During dubbing, adjusting the VOLUME, BALANCE, TREBLE and BASS controls have no effect on the recorded sound. If, however, the DSP is on, the DSP effect is recorded along with the source. * Music with DSP effect is suitable for listening to inside a car etc. Try to use the same tape formula and length for the recording tape as for the master tape. 1 Select the tape deck so that “TAPE” appears on the display by pressing the INPUT selector or button. 2 Load a prerecorded tape into the DECK A cassette compartment. Insert a blank tape into the DECK B cassette compartment. 3 Set the reverse mode switch to to record on only one side, or to (or ) for continuous recording on both sides. 4 Press the DUBBING button. * Press “NORMAL” to dub at normal speed, and “HIGH” to dub at about twice the normal speed. * Dubbing will begin from side A regardless of the side now selected. Tape Deck To stop dubbing 2 4 4 Press the stop button. * Tape A and tape B will stop at the same time. 2, 1 3, 3 4 4 Note Only tapes originally encoded with Dolby B or C NR will be dubbed onto tapes with Dolby B or C NR encoding. The Dolby NR switch will have no effect on the recording of tape B during dubbing. However, the playback tonal quality of tape A will change according to the Dolby NR switch position. TUNER DIRECT 4 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PRESET REPEAT RANDOM DOWN UP PLAY STOP DECK PLAY A/B EFFECT LEVEL - + POWER SLEEP DSP DISPLAY MODE 4 TAPE PHONO/AUX REC/PAUSE Erasing recorded tapes 0 SP/PHONES 1, 2 VOLUME - + 4 E-37 1 Load the tape to be erased into the DECK B cassette compartment. 2 Select the tape deck so that “TAPE” appears on the display by pressing the INPUT selector or button. 3 Set the reverse mode switch to side and to (or ) to erase both sides. 4 Press the REC/PAUSE button, then press the play button to erase side A of the tape, or the play button to erase side B. to erase only one HOW TO USE THE BUILT-IN TIMER Timer play By using the built-in timer, you can set the time when the unit turns on and a source begins playing automatically, and the time when the unit turns off automatically. 1 Prepare the source to be played. For tuner: Tune in to the station you will listen to. For tape deck: Load a tape into the cassette compartment. (If tapes are loaded in both the compartments, tape A takes priority of tape B, and is played back by the timer play.) Receiver For CD player: Load a disc on the disc table. 2 2 2-➀ 2-➁ Press the DISPLAY button. Whenever the DISPLAY button is pressed, the display mode changes as follows. At each mode, make a setting for the timer play, referring to the setting procedure described below. Current time (TIMER on/off mode) → → → → → ➀ ➁ Source selecting mode (TAPE, TUNER, CD) ➂ ON TIME/Time setting mode ➃ OFF TIME/Time setting mode ➄ Normal display mode * The display mode will be changed to the next mode after about 8 seconds elapse automatically. If the mode is changed before the setting is completed, call the mode again by pressing the DISPLAY button once or more. Setting procedure: E-38 ➀ At the display of current time Check to be sure that the current time is correct, and press the TIMER button so that “TIMER” appears on the display. ➁ At source selecting mode Select the source (TAPE, TUNER or CD) to be played by pressing the INPUT selector or button. * If “TUNER” is selected, soon it is changed to the frequency display mode. In this mode, you can select the station to listen to with the timer play by using the BAND button, A/B/C/D/E button and TUNER PRESET DOWN/UP buttons. POWER ➂ At ON TIME/time setting mode [“ON TIME” appears on the display, and soon it is changed to a time setting mode.] Set to the time when the timer play begins by using the HOUR button and the MINUTE button. ➃ At OFF TIME/time setting mode [“OFF TIME” appears on the display, and soon it is changed to a time setting mode.] If necessary, set to the time when you want to finish the timer play (to turn this unit off) by using the HOUR button and the MINUTE button. Even if you do not set the time, it has already been set so that the timer play finishes after 1 hour. * The TIMER button functions also in the time (ON TIME or OFF TIME) setting mode. TIME ADJ Receiver 3 DISPLAY TIMER If you will not use this unit until the timer play begins, turn the power off by pressing the POWER switch or the TIMER button. Note If a timer play setting is made and the power is not turned off, the source set for the timer play will begin playing when the time comes in place of the source played at that time. 2-➂, ➃ To cancel the timer play setting After the timer play is finished, press the DISPLAY button to call the current time. While the current time is displayed, press the TIMER button so that “TIMER” goes out from the display. If it is not canceled, the system will be turned on at the same time every day, so it can be used as an alarm. However, if you will be out at that time, cancel the timer play setting. * Unless the AC supply lead is unplugged or there is a power failure for more than 30 minutes, the time set on the timer will be retained until it is reset. How to make time setting in the ON TIME or OFF TIME mode For the hour: Press the HOUR button to change the hour to a higher value. Press and hold to change continuously. To change the hour to a lower value, while pressing the TIME ADJUST button, press the HOUR button. For the minute: Use the MINUTE button and operate it in the same way as you did to change the hour. E-39 English HOW TO USE THE BUILT-IN TIMER HOW TO USE THE BUILT-IN TIMER To begin CD playback from a desired track by the timer play. CD Player 1. Play back the track which you want to play back from the beginning of the timer play. 2. Press the RESUME button on the CD player so that “ ” appears on the display. 3. Make the timer play setting. 4. Turn the power off while the track is being played back. when the time comes, the timer play begins from the beginning of the track. * If you will not play back a CD from a designated track by the timer play, press the RESUME button so that “ ” disappears from the display. RESUME Timer recording (To record a tuner program) INPUT Receiver 1 Load a blank tape into the DECK B cassette compartment. 2 3 Tune to the station of which program you want to record. Follow step 2 of the “Timer play” on pages 38 and 39. * 4 If desired, change the setting of the reverse mode switch and the Dolby NR switch. 5 If you will not use this unit untill the timer recording begins, turn the power off by pressing the POWER switch or the TIMER button. DISPLAY TIMER TIMER REC POWER In step 2-➁, select “TUNER” by pressing the INPUT selector or button, and then press the TIMER REC button so that “REC” and the station frequency flashes alternately. To confirm the timer time setting Press the DISPLAY button. Tape Deck To cancel the setting of timer recording Press the DISPLAY button once or more so that “REC” flashes on the display. While “REC” is flashing, press the TIMER REC button. * Unless the AC supply lead is unplugged or there is a power failure for more than 30 minutes, the time set on the timer will be retained until it is reset. 4 4 Note When the timer recording is finished, the timer setting is automatically canceled to avoid repeating timer recording of the same setting. 1 E-40 English HOW TO USE THE BUILT-IN TIMER Sleep timer operation This unit can be turned off automatically. POWER Receiver Play the desired sound source. 3 Press the SLEEP button repeatedly until the desired sleep time appears in the display. The display will change as described below. (Time is displayed by the minute.) Press the SLEEP button. “SLEEP” appears on the display, and soon it is replaced by “120”. 60 ↑ AUTO MEMO 90 ↑ 120 ↑ ↑ 30 OFF SLEEP (Sleep timer is off.) ↑ DISPLAY 1 2 * The original display mode will resume about 4 seconds after the selection is made. * The SLEEP indicator illuminates to indicate that the sleep timer is on. 4 The unit will turn off automatically when the preset sleep time has passed. TUNER DIRECT 1 2 3 4 5 1 2 3 4 5 6 7 8 6 7 8 9 0 A B C D E TIME PROG TAPE EDIT +I0 STOP PLAY/PAUSE CD A/B/C/D/E TUNER PRESET REPEAT RANDOM DOWN UP PLAY STOP DECK PLAY To confirm the sleep time setting Press the SLEEP button once. “SLEEP” appears on the display, and soon it is replaced by the remaining time of the preset sleep time. To change the sleep time TAPE While the SLEEP indicator illuminates, press the SLEEP button repeatedly until the desired time appears. PHONO/AUX REC/PAUSE A/B EFFECT LEVEL POWER - + POWER SLEEP DSP DISPLAY MODE SP/PHONES To stop the sleep timer operation VOLUME - + Press the POWER switch, or press the SLEEP button repeatedly until “OFF SLEEP” appears on the display. (The SLEEP indicator will go out.) To set the sleep time using front panel buttons First press the DISPLAY button to display the current time. Within 7 seconds, press the AUTO MEMORY button. Whenever the AUTO MEMORY button is pressed, the sleep time changes. Using the timer and the sleep timer at the same time SLEEP 1 Prepare timer playback. (See pages 38 and 39.) * Do not turn the power of this unit off after the timer setting is finished. 2 Press the SLEEP button and set the sleep time. When the sleep timer operation finishes, the timer will function to turn the source on at the preset time. E-41 Notes • Do not set the timer time so that the timer will start during sleep timer operation. (Since sleep timer operation has priority, the timer will not operate.) • If the power is turned off by the sleep timer while playing back a CD with “ ” is illuminated on the display, when CD playback begins at the time set on the timer play setting, playback begins from the beginning of the track which had been being played back when the power was turned off by the sleep timer. * The “ ”indicator is switched on and off by pressing the RESUME button on the CD player. USING EXTERNAL UNITS Auxiliary (AUX) INPUT R 1 Connect the output lead of a video cassette player, video disc player, etc. to the AUX inputs of this unit. (red → right channel, white → left channel) 2 Press the INPUT selector or button once or more until “AUX” appears on the display. 3 4 Operate the unit connected to the AUX inputs. L PHONO AUX Start recording with this unit, if so desired. (See page 36.) INPUT Turntable (PHONO) R L PHONO 1 Connect the output lead of a turntable. (red → right channel, white → left channel) 2 3 Connect the GND lead of a turntable. 4 5 Operate the turntable. AUX GND E-42 Press the INPUT selector or button once or more until “PHONO” appears on the display. Start recording with this unit, if so desired. (See page 36.) Headphones • PHONES • Be sure that your headphones have a 3.5 mm (1/8”) diameter plug and are between 16 ohms and 50 ohms impedance. Recommended impedance is 32 ohms. When headphones are connected, the speakers are defeated automatically. Adjust the VOLUME control for desired volume. MAINTENANCE Internal care DECK A • • Dirty heads, capstans and pinch rollers can cause poor sound and tape jams. Clean these parts with a cotton swab moistened with commercially available head/pinch roller cleaner or isopropyl alcohol, or with a commercially available cleaning tape. After long use, the deck’s heads and capstans may become magnetized, causing poor sound. Demagnetize these parts once every 30 hours of playing/recording time by using a commercial tape head demagnetizer. Read the demagnetizer’s instructions carefully before use. External care DECK B • • E-43 Periodically clean the surfaces of this system, especially the top panel of the receiver to prevent the ventilation holes from being blocked with dust etc. Do not use chemically treated cleaning cloths or other chemicals. (See “Precautions”.) English USING EXTERNAL UNITS SPECIFICATIONS As a part of policy of continuous improvement, YAMAHA reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. ■ Receiver (RX-S50) ■ Tape Deck (KXW-S70) Minimum RMS Output Power per Channel 6 ohms, 50 Hz to 20 kHz, 0.08% THD .......................... 35W+35W 6 ohms, 1 kHz, 10% THD [U.K. and General models only] ............................... 50W+50W DIN Standard Output Power per Channel [Europe model only] 6 ohms, 1 kHz, 1% THD .......................................................... 40W IEC Power [Europe model only] 6 ohms, 1 kHz, 0.1% THD ....................................................... 35W Input Sensitivity/Impedance PHONO MM ....................................................... 2.5 mV/47 k-ohms AUX .................................................................. 300 mV/20 k-ohms Headphone Output Impedance.......................................... 68 ohms Total Harmonic Distortion (20 Hz to 20 kHz) AUX to SP OUT (17.5W/6 ohms) ......................................... 0.08% Tone Control Characteristics BASS: Boost/cut ................................................... ±10 dB (50 Hz) TREBLE: Boost/cut ............................................. ±10 dB (20 kHz) Tuning Range FM [Australia, Europe, U.K. and General models] ...................................................................... 87.5 to 108.0 MHz AM (MW) [General model] ........................................... 530 – 1,710 kHz [Australia, U.K. and Europe models] ......... 531 – 1,611 kHz LW [U.K. and Europe models only] ..................... 153 – 288 kHz Usable Sensitivity FM (75 ohms) (30 dB S/N Quieting, 1 kHz, 100% mod.) [Except Europe model]................................1.2 µV (12.8 dBf) (DIN, Mono, S/N 26 dB) [Europe model] ........................1.5 µV AM (MW)........................................................................ 280 µV/m LW ................................................................................. 560 µV/m Power Supply [Australia and U.K. models] ............................. AC 240V, 50 Hz [Europe model] ................................................. AC 230V, 50 Hz [General model] ...................... AC 110/120/220/240V, 50/60 Hz Power consumption [Australia, Europe, U.K. and General models] ............... 120W Dimensions (W x H x D)............................. 280 x 107.5 x 339.5 mm (11” x 6-7/8” x 13-3/8”) Weight ............................................................ 5.3 kg (11 lbs. 11 oz.) Power Source ................................... AC supplies from receiver unit Type ............... Auto Reverse 4-Track 2-Channel playback/recording and playback stereo double Cassette Deck Heads ................................................ PB, REC/PB : Hard Permalloy Erase : Double Gap Ferrite Motors ................................................................ DC servo motor x 2 Wow and Flutter ................................................. 50.19%, W.PEAK 0.09%, W.RMS Fast Winding Time (C-60 Tape) ........................ About 120 seconds Frequency Response (–20 dB) ........................................................ 30 – 15,000 Hz 53 dB (Normal) 30 – 16,000 Hz 53 dB (CrO2) 30 – 18,000 Hz 53 dB (Metal) Signal-to-Noise Ratio .................................. 58 dB (Dolby NR OFF) 66 dB (Dolby B NR ON) 74 dB (Dolby C NR ON) Harmonic Distortion .......................................... No more than 1.2% Channel Separation (Input Shorted 1 kHz) ................................................................................. More than 40 dB Crosstalk (Input Shorted 125 Hz).......................... More than 55 dB Dimensions (W x H x D)................................ 280 x 117.5 x 326 mm (11” x 4-5/8” x 12-13/16”) Weight ................................................................ 4.2 kg (9 lbs. 4 oz.) ■ Speaker (NX-S50) Type .................................................... Active Servo Processing type Speakers ........................................................ 13 cm (5-1/8”) woofer 5 cm (2”) tweeter Frequency Range .................................................... 50 – 20,000 Hz Sound Pressure Level.......................................................... 88.5 dB Maximum Power Handling Capacity........................................ 50W Impedance ............................................................................ 6 ohms Dimensions (W x H x D)................................ 170 x 332.5 x 222 mm (6-11/16” x 13-1/16” x 8-3/4”) Weight .......................................................... 3.3 kg (7 lbs. 4 oz.) x 2 ■ CD player (CDX-S50) Power Source ................................... AC supplies from receiver unit Type ................................................................. Compact Disc Player Signal Readout ........................... Non-contact, 3-beam semi-conductor laser pick-up D/A Converter ................................................................... 1-bit DAC Filter ......................................8-time oversampling 18-bit digital filter Wow and Flutter .........................................Below measurable limits Dimensions (W x H x D)............................. 280 x 107.5 x 322.5 mm (11” x 6-7/8” x 12-11/16”) Weight .............................................................. 3.0 kg (6 lbs. 10 oz.) E-44 If your unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. Should be service required, the servicer will need all three pieces (RX-S50, CDX-S50, KXW-S70). CAUSE SYMPTOM AC supply lead is not plugged in. Plug in the AC supply lead. No sound from one speaker Loose speaker connections. Connect properly. No sound from speakers. Internal protection circuit is functioning. Unplug the AC supply lead from the wall AC outlet, and then plug in again. Excessive static in FM broadcasts. Interference from starting motor of nearby car. Position the FM antenna as high and as far away from nearby roads as possible. Connect using a coaxial cable. Interference from thermostat of nearby electrical appliance. RECEIVER REMEDY No power even if the POWER switch is pressed. Noise increases during stereo broadcasts. Antenna input is too weak due to obstructions or excessive distance from broadcasting station. Check antenna connections. Stereo broadcasts are noisy and STEREO indicator blinks on and off. Insufficient antenna input. Install an antenna appropriate for the electric field strength of your area. Cannot select preset stations. Preset memory has been erased. Reprogram memory presets. Buzzing or static during AM (LW or MW) broadcasts. Interference from source such as lightning, flourescent lights, electric motors or thermostat of nearby electrical appliance. Problem is difficult to eliminate but can be lessened by grounding MW/LW (AM) loop antenna. TV or microprocessor is being used nearby. Move away from TV or microprocessor. Radio signal is weak or antenna is not properly connected. Properly connect MW/LW (AM) loop antenna. AM (LW or MW) broadcast sensitivity is poor. Install a multi-element type FM antenna if possible. Change orientation of MW/LW (AM) loop antenna. CD PLAYER Install an external MW/LW (AM) antenna. Can’t set timer. Current time is not set. Set current time. This unit will not operate properly. The internal microcomputer has been frozen by an external electric shock (lightning, excessive static electricity, etc.) or power supply with low voltage. Unplug the AC supply lead from the wall AC outlet, and then plug in again after about one minute. Play does not begin even if disc is loaded. Disc is upside down. Load disc label side up. Disc is dirty. Clean disc. No sound. Input selector setting is incorrect. Select “CD” by the INPUT selector buttons. Sound stops suddenly (always at same spot). Disc is dirty. Clean disc. Volume set too high. Lower volume. Tape won’t move during playback or recording. Slack tape wrapped around pinch roller. Take up slack with a pencil before using. Can’t record. Erasure prevention tab is broken off. Replace tape or cover erasure prevention hole with cellophane tape. Head is dirty. Clean heads. Head is dirty. Clean heads. Head has become magnetized. Demagnetize heads with head eraser. Tape is worn. Replace tape. Poor sound quality. Dolby NR switch is set to wrong position. Set to positions matching those used when tape was recorded. Stereo balance is poor. Head is dirty. Clean heads. Excessive noise. Head is dirty. Clean heads. Head has become magnetized. Demagnetize heads with head eraser. Tape is worn. Replace tape. Slack tape coming out of cassette shell. Take up slack by turning reels with a pencil. Tape is creased or torn. Replace with new tape. Endless tape is being used. Don’t use endless tapes. Silent gaps between selections are too short. The function for searching the beginning of desired selections won’t operate unless the silent gaps between selections are at least four seconds long. TAPE DECK Sound is distorted or fades out. Tape travel stops in middle of playback or recording. Can’t find the beginning of desired selections on tape. Excessively soft passages in middle of selections. REMOTE CONTROL Conversation etc. is recorded. Remote control doesn’t work. TV functions strangely when the remote control is used. Batteries are dead. Replace batteries. Remote control is too far away or is being used at incorrect angle. Use within 6 m and 60° radius. Direct sunlight or lighting (of an inverter type of flourescent lamp etc.) is striking the remote control sensor of the main unit. Change position of the main unit. Remote control is being used near TV set with a remote control sensor. Move TV farther away or cover its remote control sensor. E-45 English TROUBLESHOOTING YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA VQ 98180
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Yamaha CC-50 Manual de usuario

Categoría
Reproductores de CD
Tipo
Manual de usuario