Sylvania 6620 LDF Manual de usuario

Marca: Sylvania

Modelo: 6620 LDF

Categoría: Reproductores de DVD

Tipo: Manual de usuario

Este manual también es adecuado para

6620

MENU SELECTCHANNELVOLUME POWER

EJECTPLAYSTOP

1.Read instructions-All the safety and operating instructions

should be read before the appliance is operated.

2.Retain Instructions-The safety and operating instructions

should be retained for future reference.

3.Heed Warnings-All warnings on the appliance and in the

operating instructions should be adhered to.

4.Follow Instructions-All operating and use instructions

should be followed.

5.Cleaning-Unplug the unit from the wall outlet before clean-

ing. Do not use liquid cleaners or aerosol cleaners. Use a

damp cloth for cleaning.

EXCEPTION: A product that is meant for uninterrupted

service and, that for some specific reason, such as the possi-

bility of the loss of an authorization code for a CATV con-

verter, is not intended to be unplugged by the user for clean-

ing or any other purpose, may exclude the reference to

unplugging the appliance in the cleaning description other-

wise required in item 5.

6.Attachments-Do not use attachments not recommended by

the unit manufacturer as they may cause hazards.

7.Water and Moisture-

Do not use this unit near water-for

example, near a bath tub, wash bowl, kitchen sink, or laundry

tub, in a wet basement, or near a swimming pool, and the like.

8.Accessories-Do not place this unit

on an unstable cart, stand, tripod,

bracket, or table. The unit may fall,

causing serious injury to someone,

and serious damage to the appliance.

Use only with a cart, stand, tripod,

bracket, or table recommended by

the manufacturer, or sold with the

unit. Any mounting of the appliance should follow the man-

ufacturer’s instructions and should use a mounting accessory

recommended by the manufacturer. An appliance and cart

combination should be moved with care. Quick stops, exces-

sive force, and uneven surfaces may cause the appliance and

cart combination to overturn.

8.AMEUBLES- Cet appareil ne doit

être placé que sur un meuble (avec

ou sans roulettes) recommandé par

le fabricant. Si vous l’installez sur

un meuble à roulettes, déplacez les

deux ensembles avec précaution. Un

arrêt brusque, l’utilisation d’une

force excessive et des surfaces

irrégulières risquent de déstabiliser l’ensemble et de le ren-

verser.

SYMBOLE D'AVERTISSEMENT POUR

LES COMPOSANTES

APPAREIL ET MEUBLE A ROULETTES

S3126A

PORTABLE CART WARNING

S3126A

- 2 - EN

IMPORTANT SAFEGUARDS

The serial number of this product may be found on the back of the unit. No other unit has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

•

If you need to replace these accessories, please refer to the PART NO. under the illustrations and call our

help line mentioned on the front page.

•

Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators

(Splitter). Contact your local electronics store for these items.

BatteriesRemote Control Unit

2 AA Batteries( NE240UD )

Owner’s Manual

( 1EMN20477 )

SUPPLIED ACCESSORIES

9.Ventilation-Slots and openings in the cabinet and the back

or bottom are provided for ventilation and to ensure reliable

operation of the unit and to protect it from overheating, and

these openings must not be blocked or covered. The open-

ings should never be blocked by placing the unit on a bed,

sofa, rug, or other similar surface. This unit should never be

placed near or over a radiator or heat register. This unit

should not be placed in a built-in installation such as a

bookcase or rack unless proper ventilation is provided or

the manufacturer’s instructions have been adhered to.

10.Power Sources-This unit should be operated only from the

type of power source indicated on the marking label. If you

are not sure of the type of power supply to your home, con-

sult your appliance dealer or local power company. For the

units intended to operate from battery power, or other

sources, refer to the operating instructions.

11.Grounding or Polarization-This unit is equipped with a

polarized alternating-current line plug(a plug having one

blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try revers-

ing the plug. If the plug should still fail to fit, contact your

electrician to replace your obsolete outlet. Do not defeat the

safety purpose of the polarized plug.

12.Power-Cord Protection-Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying par-

ticular attention to cords at plugs, convenience receptacles,

and the point where they exit from the appliance.

13.Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the unit, be sure the antenna

or cable system is grounded so as to provide some protec-

tion against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA

No. 70, provides information with respect to proper

grounding of the mast and supporting structure, grounding

of the lead-in wire to an antenna discharge unit, size of

grounding conductors, location of antenna-discharge unit,

connection to grounding electrodes, and requirements for

the grounding electrode. (Fig. A)

14.Lightning-For added protection for this unit receiver dur-

ing a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This will

prevent damage to the unit due to lightning and power-line

surges.

15.Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

16.Overloading-Do not overload wall outlets and extension

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this unit through openings as they may touch danger-

ous voltage points or short out parts that could result in a

fire or electric shock. Never spill liquid of any kind on the

unit.

18.Servicing-Do not attempt to service this unit yourself as

opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified

service personnel.

19.Damage Requiring Service-Unplug this unit from the wall

outlet and refer servicing to qualified service personnel

under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

unit.

c. If the unit has been exposed to rain or water.

d. If the unit does not operate normally by following the oper-

ating instructions. Adjust only those controls that are cov-

ered by the operating instructions, as improper adjustment

of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the unit to its normal operation.

e. If the unit has been dropped or damaged in any way.

f. When the unit exhibits a distinct change in performance,

this indicates a need for service.

20.Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

21.Safety Check-Upon completion of any service or repairs to

this unit, ask the service technician to perform routine safe-

ty checks to determine that the unit is in proper operating

condition.

22.Heat-This unit product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

- 3 - EN- 3 - EN

GROUND CLAMPS

NEC - NATIONAL ELECTRICAL CODE

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

S2898A

WIRE

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

ELECTRODE SYSTEM

(NEC ART 250, PART H)

SERVICE

EQUIPMENT

CLAMP

ANTENNA

LEAD IN

ANTENNA

POWER SERVICE GROUNDING

GROUND

ELECTRIC

FIGURE A

- 4 - EN

PRECAUTIONS

- 4 - EN- 4 - EN

IMPORTANT COPYRIGHT INFORMATION

Unauthorized copying, broadcasting, public performance

and lending of discs are prohibited.

This product incorporates copyright protection technology

that is protected by U.S. patents and other intellectual prop-

erty rights. Use of this copyright protection technology must

be authorized by Macrovision, and is intended for home and

other limited viewing uses only unless otherwise authorized

by Macrovision. Reverse engineering or disassembly is pro-

hibited.

FCC WARNING- This equipment may generate or use

radio frequency energy. Changes or modifications to

this equipment may cause harmful interference unless

the modifications are expressly approved in the instruc-

tion manual. The user could lose the authority to oper-

ate this equipment if an unauthorized change or modi-

fication is made.

RADIO-TV INTERFERENCE

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reason-

able protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful inter-

ference to radio communications.

However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference

by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment and

receiver.

3) Connect the equipment into an outlet on a circuit differ-

ent from that to which the receiver is connected.

4) Consult the dealer or an experienced radio/TV techni-

cian for help.

LASER SAFETY

This unit employs a laser. Only a qualified service person

should remove the cover or attempt to service this device,

due to possible eye injury.

CAUTION: USE OF CONTROLS OR ADJUSTMENTS

OR PERFORMANCE OF PROCEDURES OTHER

THAN THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER RADIA-

TION WHEN OPEN AND INTERLOCK DEFEATED.

DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK MECHA-

NISM.

This Class B digital apparatus complies with Canadian

ICES-003.

Cet appareil numérique de la classe B est conforme à la

norme NMB-003 du Canada.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC

ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS

LARGE DE LA FICHE DANS LA BORNE CORRE-

SPONDANTE DE LA PRISE ET POUSSER JUSQU’AU

FOND.

A NOTE ABOUT RECYCLING

Batteries should never be thrown away or incinerated but

disposed of in accordance with your local regulations con-

cerning chemical wastes.

The caution marking is located on the rear of the cabinet.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

THIS SYMBOL INDICATES THAT

DANGEROUS VOLTAGE

CONSTITUTING A RISK OF ELECTRIC

SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE

ARE IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS IN THE

LITERATURE ACCOMPANYING THE

APPLIANCE.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

For safe operation and satisfactory performance of

your unit, keep the following in mind when selecting

a place for its installation:

•

Shield it from direct sunlight and keep it away

from sources of intense heat.

•

Avoid dusty or humid places.

•

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes

at the top or bottom of the unit. Do not place the

unit on a carpet because this will block the ventila-

tion holes.

•

Install unit in a horizontal position.

•

Avoid locations subject to strong vibration.

•

Do not place the unit near strong magnetic fields.

•

Avoid moving the unit to locations where tempera-

ture differences are extreme.

•

Be sure to remove a disc and unplug the AC power

cord from the outlet before carrying the unit.

•

Do not handle the power cord with wet hands.

•

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

•

If by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

•

Do not put your fingers or objects into the unit

disc slot.

•

Do not place anything directly on top of the unit.

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place

or after heating a cold room or under conditions of

high humidity. If a DVD is played in a unit which

has moisture, it may damage the DVD and the unit.

Therefore when the condensation occurs inside the

unit, turn the unit on and allow at least 2 hours for

the unit to dry out.

The following symbols below appear in some head-

ings in this manual.

: Description refers to playback of DVD video discs

(in the DVD mode).

: Description refers to playback of Audio CDs

(in the DVD mode).

: Description refers to playback of CDs with MP3

files (in the DVD mode).

: Description refers to the items to be set by the

QUICK mode (in the DVD mode).

You can adjust the stand to change the angle of the

TV (-5° to 10°).

QUICK

- 5 - EN- 5 - EN- 5 - EN- 5 - EN

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

LOCATION

WARNING

SYMBOLS USED IN THIS MANUAL

TILT STAND

10°

-5°

SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . .2

IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . .2

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE . . . . . . . . . . . . . . . .5

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

SYMBOLS USED IN THIS MANUAL . . . . . . . . . . . . . .5

TILT STAND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . .6

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

OPERATING CONTROLS AND FUNCTIONS . . . . . . . . . .8

INSTALLING THE BATTERIES . . . . . . . . . . . . . . . . . .9

PREPARATION FOR USE . . . . . . . . . . . . . . . . . . . . . . .10

ANTENNA/CABLE CONNECTION . . . . . . . . . . . . . . .10

EXTERNAL CONNECTION . . . . . . . . . . . . . . . . . . . . .11

TV OPERATION AND SETTINGS . . . . . . . . . . . . . . . . .12

WATCHING A TV PROGRAM . . . . . . . . . . . . . . . . . .12

CHANNEL SET UP . . . . . . . . . . . . . . . . . . . . . . . . . .13

PICTURE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . .14

BACK LIGHT SETTING . . . . . . . . . . . . . . . . . . . . . . .14

SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

CLOSED CAPTION SYSTEM . . . . . . . . . . . . . . . . . .15

MTS (Multi-Channel Television Sound) System . . . . . .15

V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

TV RATING SET UP . . . . . . . . . . . . . . . . . . . . . . .16

MPAA RATING SET UP . . . . . . . . . . . . . . . . . . . .17

CHANGE ACCESS CODE . . . . . . . . . . . . . . . . . .17

MENU LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . .17

ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . .18

UNPLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . . . . .18

PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .19

DISC MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

STEP BY STEP PLAYBACK . . . . . . . . . . . . . . . . . . .20

FAST FORWARD / FAST REVERSE . . . . . . . . . . . . .21

SLOW FORWARD / SLOW REVERSE . . . . . . . . . . . .21

ZOOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

SEARCH FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . .22

TRACK SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

TITLE / CHAPTER SEARCH . . . . . . . . . . . . . . . . . . .22

TIME SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

MARKER SETUP SCREEN . . . . . . . . . . . . . . . . . . . .23

SPECIAL PLAYBACK FUNCTION . . . . . . . . . . . . . . . . .24

REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

A-B REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

RANDOM PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . .25

CHANGING THE SETTINGS . . . . . . . . . . . . . . . . . . . . .26

SUBTITLE LANGUAGE . . . . . . . . . . . . . . . . . . . . . . .26

AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . .26

STEREO SOUND MODE . . . . . . . . . . . . . . . . . . . . . .26

CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . . . . . . .27

BLACK LEVEL SETTING . . . . . . . . . . . . . . . . . . . . . .27

VIRTUAL SURROUND . . . . . . . . . . . . . . . . . . . . . . . .27

THE ON-SCREEN INFORMATION . . . . . . . . . . . . . . . . .28

CHANGING THE DVD SET UP ITEMS . . . . . . . . . . . . . .29

CUSTOM MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

LANGUAGE SETTING . . . . . . . . . . . . . . . . . . . . .29

DISPLAY SETTING . . . . . . . . . . . . . . . . . . . . . . . .30

AUDIO SETTING . . . . . . . . . . . . . . . . . . . . . . . . .30

PARENTAL CONTROL . . . . . . . . . . . . . . . . . . . . .31

OTHER SETTINGS . . . . . . . . . . . . . . . . . . . . . . . .31

INITIALIZE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . .33

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

DISC HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

- 6 - EN- 6 - EN- 6 - EN- 6 - EN

TABLE OF CONTENTS

TV SECTION

VD SECTION

- 7 - EN- 7 - EN- 7 - EN- 7 - EN

•

MTS/SAP Tuner

•

Infrared remote control

•

Trilingual on screen TV setup display available in

English, Spanish or French

•

181 channel capability PLL frequency synthesizer

tuner with direct station call

(A converter may be

necessary to view scrambled cable channels.)

•

Closed Caption Decoder–You may view specially

labeled (cc) TV programs, movies, news, etc. with

either a dialogue caption or text display added to

the program.

•

Auto power off system–If there is no air signal input

from the antenna terminal and no operation for 15

minutes, the unit will turn itself off automatically.

•

Sleep timer–Allows you to have the unit automati-

cally turn off at a desired time.

•

V-CHIP–Enables parents to prevent their children

from watching inappropriate material on TV.

FEATURES

TV Mode

DVD Mode

•

Dolby Digital sound

This unit can handle Dolby Digital surround sound

having 5.1 channels when connected to a Dolby

Digital decoder.

•

Still/fast/slow/step playback

Various playback modes are available including

still pictures, fast forward/reverse, slow motion and

step frames.

•

Random playback for Audio CD and MP3

This unit can shuffle the order of tracks to play

them in random order.

•

Program playback for Audio CD and MP3

You can program the order of tracks to play them

in any desired order.

•

DVD menus in a desired language

You can display DVD menus in a desired lan-

guage, if available on a DVD.

•

Screen saver

If the screen saver program is set to ON, it starts

when there is no input from the unit for 5 minutes

in stop mode.

•

Subtitles in a desired language

You can select a desired language for the display

subtitles, if that language is available on a disc.

•

Selecting a camera angle

You can select the desired camera angle, if a disc

contains sequences recorded from different angles.

•

Choices for audio language and sound mode

You can select the desired audio language and

sound mode, if different languages and modes are

available on a disc.

•

Parental lock

You can set the control level to limit playback of

discs which may not be suitable for children.

•

Automatic detection of discs

This unit automatically detects if the loaded disc is

DVD, Audio CD or MP3 on disc.

•

On-screen display

Information about the current operation can be dis-

played on a TV screen, allowing you to confirm

the currently active functions (such as program

playback), on the TV screen using the remote con-

trol.

•

Chapter search / Title search / Track search / Time

•

Repeat

Chapter / Title / Track / Group / All / A-B

•

Zoom

Allows you to enlarge video image.

•

Marker

The part designated by user can be called back.

•

Resume Play

User can resume to playback from the part at

which the play was stopped.

•

Virtual Surround

•

Bit rate indication

•

DRC (Dynamic range control)

You can control the range of sound volume.

1.POWER button

(P.12)

Press to turn the power on and off.

2.PICTURE button

(P.14)

Press to adjust the picture.

Number buttons

(P.13)

Press to select a desired channel number directly.

+100 button (For TV mode)

Press to select channels higher than 99.

+10 button (For DVD mode)

Press to enter desired numbers higher than 9.

SLEEP button

(P.14)

Press to set the Sleep Timer.

SKIP H / G buttons

(P.22)

Press once to skip chapters

tracks to a desired point.

6.PLAY O button

(P.19)

Press to playback the disc.

PAUSE F button

(P.20)

Press to pause the current disc operation.

DISPLAY button

For TV mode

(P.15):

Press to display the current channel number on

the TV screen.

For DVD mode

(P.28):

ress to display the current status on the TV screen.

9.SETUP button

(P13, P.29)

Press to enter or exit the setup menu of TV/DVD.

10.

TITLE button

(P.20)

Press to display the title menu.

11.

CLEAR button

(P12, P.22)

Press to clear/cancel a setting currently entered.

Press to clear “DISC INSIDE” display.

12.

MODE button

(P.25)

Press to call up the program/random screen in

stop mode.

Press to call up the Black Level Setting/Virtual

Surround screen during playback.

13.

SEARCH MODE button

(P.22, P23)

Press to locate a desired point.

14.

AUDIO button

(P.26)

For TV mode (P.15): Press to select TV sound

mode (STEREO/SAP/MONO).

For DVD mode

(P.26): Press to select a desired

audio language (if available).

15.

EJECT A button

(P.19)

Press to remove a disc from the unit.

16.

SELECT button

(P.12)

Press to select the TV mode, external input mode

or DVD mode.

17.

CH.

buttons

(P.12)

Press to select memorized channels.

18.

VOL.

buttons

(P.12)

Press to control the volume level for the DVD

and TV.

19.

MUTE button

(P.12)

Press to mute the sound or press it again to

restore sound.

20.

ZOOM button

(P.21)

Press to enlarge the part of a DVD-reproduced

image.

21.

REV

button (P.21)

Press to view the DVD picture in fast/slow

reverse motion.

FWD

button (P.21)

Press to view in fast/slow forward motion.

22.

STOP C button

(P.19)

Press to stop operation of the disc.

23.

DISC MENU button

(P.20)

Calls up the DVD menu.

Calls up the file list in MP3 disc.

24.

ENTER button

(P.16)

Press to accept a setting.

25.

K (Up) / L (Down) / { (Left) / B (Right) buttons

Press to select or adjust menu items.

- 8 - EN- 8 - EN- 8 - EN- 8 - EN- 8 - EN

- REMOTE CONTROL

REV

SLOW

PLAY

STOP

FWD

ENTER

PAUSE

DISC

RETURNTITLESETUP

REPEATSEARCH MODE

CLEAR

MODE

DISPLAY

ANGLESUBTITLEAUDIO

SKIP

SELECT

POWER

PICTURE EJECT

CH.

VOL.

MUTEZOOM

SLEEP

123

456

789

0 +10

+100

OPERATING CONTROLS AND FUNCTIONS

[Fig. 1]

NOTE

•

When you select DVD mode, press [PLAY

] or [EJECT

] first or insert a disc into the disc slot.

Otherwise, the DVD features are not operated.

31. STOP P button

(P.19)

Press to stop operation of the disc.

32.

MENU button

Press to enter or exit the setup menu of TV/DVD.

33.

VOLUME

buttons

(P.12)

Press to control the volume level for the DVD

and TV.

34.

CHANNEL

buttons

(P.12)

Press to select memorized channels.

35.

SELECT button

(P.12)

Press to select to TV mode, external input mode

or DVD mode.

36.

POWER button

(P.12)

Press to turn the power on and off.

37. EJECT

button

(P.19)

Press to remove a disc from the unit.

38.

Remote sensor window

39. PLAY O button

(P.19)

Press to playback of the disc.

- 9 - EN

26.

RETURN button

(P.27)

Press to return to the previous screen in the setup

menu.

27.

A-B button

(P.24)

Press to repeat the playback of a selected section.

28.

ANGLE button

(P.27)

Press to change the camera angle to see the

sequence being played back from a different angle

(if available).

29. REPEAT button

(P.24)

Repeats playback of the current disc, title, chap-

ter, group or track.

30.

SUBTITLE button

(P.26)

Press to select a desired subtitle language.

- FRONT PANEL

MENU SELECTCHANNELVOLUME POWER

EJECTPLAYSTOP

31 33 34 3532 36 37 3938

MENU SELECTCHANNELVOLUME POWER

EJECTPLAYSTOP

INSTALLING THE BATTERIES

1 Open the battery compartment cover by

pressing the cover on the remote unit in the

direction of the arrow.

2 Insert 2 “AA” penlight batteries into the bat-

tery compartment in the direction indicated by

the polarity (+/-) markings.

3 Replace the cover.

BATTERY PRECAUTIONS

•

Be sure to follow the correct polarity as indicated

in the battery compartment. Reversed batteries

may cause damage to the device.

•

Do not mix different types of batteries together

(e.g. Alkaline and Carbon-Zinc) or old batteries

with fresh ones.

•

If the device is not to be used for a long period of

time, remove the batteries to prevent damage or

injury from possible battery leakage.

•

Do not try to recharge batteries not intended to be

recharged; they can overheat and rupture.

[Fig. 2]

NOTE

•

We do not recommend the use of universal remote controls. Not all of the functions may be controlled

with a universal remote control.

If you decide to use a universal remote control with this unit, please be aware that the code number given

may not operate this unit. In this case, please call the manufacturer of the universal remote control.

IF YOU HAVE A JACK ON THE WALL

Connect the TV to the wall-mounted antenna jack

with on RF cable (commercially available).

IF YOU HAVE A WIRED CABLE

Connect the TV to the wired antenna cable.

•

Before plugging the antenna into the ANT. jack of the

unit, check that the pin is not bent. If it is bent,

straighten the pin as illustrated, then plug the pin into

the ANT. jack of the unit.

•

Cables used here are commercially available.

•

For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. jack

before moving the unit.

NOTE

- 10 - EN

PREPARATION FOR USE

ANTENNA/CABLE CONNECTION

- ANTENNA/CABLE CONNECTION

(

)

-V

VIDEO2

CPMPONENT

AUDIO

VIDEO1

RF Cable

[Rear of this unit]

from Cable Company

or Satellite Antennna

ANT

(

)

VIDE

-V

VIDEO2

CPMPONENT

AUDIO

VIDEO1

ANT

EAD PHO

ANT

OUT IN

75-ohm

Coaxial Cable

Cable Box

or Satellite Box

[Rear of this unit]

from Cable Company

or Satellite Antenna

For CATV system installer:

•

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding

system of the building as close to the point of cable entry as practical.

NOTE

Bent pin

Cable

Plug

(Needs to be

straightened)

(Straight pin)

NOTE

WHEN USING CABLE BOX/SATELLITE

BOX

If your cable service supplies you with a converter

box or if you use a satellite system, you can use the

basic connection shown above.

Channel selection must be made with the converter

box or satellite box. This means that channels cannot

be changed using the remote control of this unit.

- CABLE/SATELLITE BOX CONNECTION

•

The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital sound by an MD or DAT deck.

•

If connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “BITSTREAM” for audio output in the setup mode. (Refer to page 30.)

•

Unless connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “PCM” for audio output in the setup mode. Playing

a unit using incorrect settings may generate noise distortion and may also damage the speakers. (Refer to page 30.)

NOTE

•

If your own equipment is monaural (has only one Audio jack), connect the Audio cable to AUDIO L jack of this unit.

•

If you connect Video jack and S-VIDEO jack simultaneously, the S-VIDEO jack is given priority over the VIDEO jack.

- AUDIO OUTPUT

- VIDEO2 INPUT

You can connect this unit to your own Audio/Video

equipment.

•

Be sure to turn off the power to all components in

the system before connecting another component.

•

Refer to the Owner’s Manuals for the equipments

to be connected to the unit.

- VIDEO1 INPUT

- 11 - EN

EXTERNAL CONNECTION

(

)

VIDE

CPMPONENT

AUDIO

VIDE

AUDIO

VIDEO2

VIDEO1

Audio Cable

Video Cassette

Recorder

ex.

(OUT)

S-Video Cable

Video Cable

S-VIDEO

VID

VIDEO1

AUDIO

NOTE

COMPONENT

VIDEO2

AUDIO

Component

Video Cable

Audio Cable

Video Game

Video Camera

ex.

(OUT)

Use this connection if your own A/V equipment (e.g.

VCR) has Video output and Audio out jacks. When

using S-Video cable, better picture is available.

Use this connection if your own A/V equipment (e.g.

video camera, video game) has COMPONENT

Video output (Y, Pb, Pr) jacks. You can enjoy the

best picture with this connection.

DIGITAL

AUDIO OUT

(COAXIAL)

Home Audio System

Dolby Digital decoder

To COAXIAL DIGITAL

AUDIO INPUT jack

You can enjoy DVD sound with more

presence by connecting digital audio

equipment such as Dolby Digital decoder.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol

are trademarks of Dolby Laboratories.

When you use the external input, select “VIDEO1” or

“VIDEO2” by pressing [SELECT]. (Refer to page 12.)

•

To use the VIDEO1 input jacks, select “VIDEO1”.

•

To use the VIDEO2 input jacks, select “VIDEO2”.

NOTE

•

Shaded buttons are used for following operation.

1 Plug the power cord into a standard

AC outlet.

•

If any digits are displayed in the corner of the

screen, press [POWER] without unplugging

the power cord.

2 Press [POWER] to turn on the unit.

3 Press [CH.

] to select the desired chan-

nel number.

Press the Number buttons to enter the

desired channel number.

For channel number selection with number

buttons:

•

To select single-digit channel number, press

[0]

first. (e.g. Press [0] [2] for channel 2.)

•

To select cable channels which are higher

than 99, press [+100/+10] first.

(e.g. Press [+100/+10] [2] [5] for channel 125.)

4 Press [VOL.

] to select the desired vol-

ume level.

•

Press [MUTE] to instantly mute the sound.

Press it again to restore the previous volume

level.

•

If you press [CH.

] in the DVD mode,

you can change the TV channels. Even if you

turn off the unit in the DVD mode, when you

turn it on again, it will go into the TV mode.

TO WATCH CABLE OR SATELLITE

CHANNEL

If the unit is connected to a cable box or satellite

box, press [CH.

] to select CH3 or CH4

according to the output channel setting of the device

and select desired channel on that device.

TO WATCH EXTERNAL INPUT

When an external equipment is connected to the front

AUDIO/VIDEO input jacks, press [SELECT] or

[CH.

] repeatedly until “VIDEO1” or

“VIDEO2” appears on the screen.

•

If a disc is inside the unit, “DISC INSIDE” mes-

sage is displayed on the screen for 10 seconds.

•

To clear the message instantly, press [CLEAR].

- 12 - EN- 12 - EN- 12 - EN- 12 - EN- 12 - EN- 12 - EN- 12 - EN- 12 - EN- 12 - EN

TV OPERATION AND SETTINGS

WATCHING A TV PROGRAM

VOLUME 20

C C C C C C C C C C C C C C C C

TV SECTION

REV

SLOW

PLAY

STOP

FWD

ENTER

PAUSE

DISC

RETURNTITLESETUP

REPEATSEARCH MODE

CLEAR

DISPLAY

SKIP

SELECT

POWER

PICTURE EJECT

CH.

VOL.

MUTEZOOM

SLEEP

123

456

789

0 +10

+100

CH.

POWER

123

456

789

0 +10

+100

VOL.

NOTE

DISC INSIDE

- 13 - EN

AUTO CHANNEL PROGRAMMING

As the initial setting, this unit has memorized all

channels, including the ones not available in your

area. This feature automatically puts only available

channels into the memory.

1 Press [SETUP] then press [

] or [

] to point

to “CHANNEL SET UP”.

2 Press [ENTER] then press [

] or [

] to point

to “AUTO PRESET CH”.

3 Press [ENTER].

•

The tuner scans and memorizes all the active

channels in your area.

•

The tuner stops on the lowest memorized channel.

•

When “AUTO PRESET CH” is activated

where there is no TV signal input, “NO TV

SIGNAL” will appear on the display after the

completion of channel scanning.

•

The unit may recognize CATV channels to be

TV channels if reception condition is poor. In

this case, check the antenna connection and try

“AUTO PRESET CH” again when reception

conditions are better.

•

Channel memory programming is NOT nec-

essary when connected to a cable box or satel-

lite box. Just select the channel for cable box

or satellite input (ex. CH3) on the unit, then

select your desired channel on the cable box

or satellite box.

ADDING/DELETING CHANNELS

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you can

add the deleted channel into the memory again.)

1 Press [SETUP] then press [

] or [

] to point

to “CHANNEL SET UP”.

2 Press [ENTER] then press [

] or [

] to point

to “ADD/DELETE CH”.

3 Press [ENTER] then press the Number but-

tons or [CH.

] to select the desired

channel number.

4 Press [ENTER] then the channel number

turned to red. The channel is deleted from

memory. If the channel number turned to

blue, the channel is added into memory.

•

To delete another channel, repeat steps 3 to 4.

•

If you press [ENTER] again, the channel is

memorized again.

5 Press [SETUP] to exit the menu.

•

To confirm that channel(s) has been deleted

or added, press [CH.

– CHANNEL SET UP –

B ADD / DELETE CH (CATV)

AUTO PRESET CH

- TV SET UP -

B CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

BACK LIGHT [BRIGHT]

SETUP

ENTER

123

456

789

0 +10

+100

ENTER

SETUP

- TV SET UP -

B CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

BACK LIGHT [BRIGHT]

ENTER

– CHANNEL SET UP –

ADD / DELETE CH (CATV)

B AUTO PRESET CH

ENTER

CHANNEL SET UP

NOTE

Added channel : Light blue

Deleted channel : Light red

NOTE

ADD/DELETE

TV SECTION

TV OPERATION AND SETTINGS

- 14 - EN

•

Shaded buttons are used for following operation.

The unit’s picture controls, brightness, contrast,

color, tint and sharpness, are preset to factory speci-

fications. Although they are usually the best, you

may need to make some further adjustments for a

more natural looking image.

1 Press [PICTURE] then press [

] or [

] to

select the desired control “BRIGHTNESS”,

“CONTRAST”, “COLOR”, “TINT” or “SHARP-

NESS”.

2 Press

[

s] or [B

]

to adjust to your desired

level within 5 seconds.

•

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

•

The picture control display will disapper automati-

cally after 10 seconds unless you press any buttons.

•

Magnetism from near by appliances and speakers

might affect the color of TV picture. If this hap-

pens, press [POWER] to turn off the TV and turn

it on again after about 30 minutes.

1 Press [SETUP] then press [

] or [

] to point

to “BACK LIGHT”.

2 Press [ENTER] then press [

] or [

] to

select to “BRIGHT”, “NORMAL” or “DARK”.

3 Press [SETUP].

The Sleep Timer function turns off the unit without

using [POWER] after a desired period of time.

1 Press [SLEEP].

2 Press [SLEEP] repeatedly until the desired

sleep time is displayed.

•

Each press increases the time by 10 minutes up

to 90 minutes.

•

After 5 seconds, the Sleep Timer setting will

disappear automatically.

•

If you select “SLEEP 0 MINUTE”, Sleep Timer

setting is cancelled.

PICTURE CONTROL

BRIGHTNESS

PICTURE

SLEEP TIMER

SLEEP

REV

SLOW

PLAY

STOP

FWD

ENTER

PAUSE

DISC

RETURNTITLESETUP

REPEATSEARCH MODE

CLEAR

MODE

DISPLAY

ANGLESUBTITLEAUDIO

SKIP

VOL.

MUTEZOOM

SLEEP

0 +10

+100

SELECT

POWER

PICTURE EJECT

BACK LIGHT SETTING

NOTE

BRIGHTNESS to decrease to increase

brightness brightness

CONTRAST to decrease to increase

contrast contrast

COLOR to pale to brilliant

TINT to purple to green

SHARPNESS to soft to clear

SETUP

- TV SET UP -

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

B BACK LIGHT [BRIGHT]

ENTER

SETUP

SLEEP 0 MINUTE

SLEEP

- 15 - EN

You can view specially labeled (cc) TV programs,

movies, news and pre-recorded tapes with either a

dialogue caption or text display.

CAPTION mode: You can watch dramas, movies and

news while captioning the dialogues and the contents

of news.

TEXT mode: You can watch half screen text informa-

tion if you want.

1-2: You may get these captions or text information

by selecting either “1” or “2”. Caption “2” is usually

used for a second language if available.

•

Not all programs are broadcast with closed cap-

tions. Your unit is designed to provide error free

closed captions from high quality antenna, cable

and VCR signals. Conversely, poor quality sig-

nals are likely to result in caption errors or no

captions at all. Common signal conditions which

may cause caption errors are listed below:

–

Automobile ignition noise

–

Electric motor brush noise

–

Weak snowy reception on TV screen

–

Multiplex signal reception displaying picture

ghosts or airplane flutter

•

If the unit displays a black box on the TV

screen, this means that the unit is set to the

TEXT mode. To clear screen, select “CAP-

TION1”, “CAPTION2” or “OFF”.

1 Press [SETUP] then press [K] or [L] to point

to “CAPTION”.

2 Press [ENTER] repeatedly to select the

desired caption menu “CAPTION1”, “CAP-

TION2”, “TEXT1” or “TEXT2”.

•

If you select “OFF”, Closed Caption System set-

ting is cancelled.

3 Press [SETUP] to exit the menu.

•

Even if there is a power failure of any

kind, the unit will retain its memory for

this feature.

TO SELECT TV SOUND MODE

1 Press [AUDIO] repeatedly to select the MTS

output mode.

•

The output mode changes as described below

every time you press [AUDIO].

* Second Audio Program (SAP):

Sometimes broadcasters add another channel of

audio to the programs they air. This is usually a

secondary language or perhaps a radio station.

•

After 5 seconds, the current audio status will

disappear from the TV screen.

•

The initial setting is “STEREO”.

•

This setting is saved even if the unit is turned

off or the AC cord is unplugged.

TO CHECK THE SOUND STATUS

By pressing [DISPLAY], the status shown below

will appear on the display when you receive a broad-

cast on the unit tuner channel you are watching.

1) When a program is broadcast in stereo,

“STEREO” appears on the TV screen.

2) When a program is broadcast in second audio,

“SAP” appears on the TV screen.

3) When a program broadcast both in stereo and sec-

ond audio, “STEREO/SAP” appears on the TV

screen.

CLOSED CAPTION SYSTEM

- TV SET UP -

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

B CAPTION [OFF]

BACK LIGHT [BRIGHT]

- TV SET UP -

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

B CAPTION [CAPTION1]

BACK LIGHT [BRIGHT]

SETUP

ENTER

SETUP

MTS (Multi-Channel Television

Sound) System

AUDIO

NOTE

STEREO

SAP

MONO

NOTE

TV SECTION

TV OPERATION AND SETTINGS

STEREO

CH 123

STEREO/SAP

- 16 - EN- 16 - EN- 16 - EN- 16 - EN

•

Shaded buttons are used for following operation.

V-CHIP SET UP

This feature enables parents to prevent their children

from watching inappropriate material on TV. When

you try to access a program which is blocked, “PRO-

TECTED PROGRAM by ...” message appears on

the TV screen.

1 Press [SETUP] then press [

] or [

] to point

to “V-CHIP SET UP”.

2 Press [ENTER] then press the Number

Buttons to enter the access code.

•

For the first time set-up or in the event the unit

has lost power, enter the default code of 0000.

3 Press [K] or [L] to select “TV RATING”,

“MPAA RATING” or “CHANGE CODE” then

press [ENTER].

TV RATING: See

TV RATING SET UP

MPAA RATING: See

MPAA RATING SET UP

CHANGE CODE: See

CHANGE ACCESS CODE

TV RATING SET UP

Follow steps

in the V-CHIP SET UP.

4 Press [K] or [L] to select the desired TV rat-

ing to be blocked then press [ENTER] repeat-

edly to set “BLOCK” or “VIEW”.

•

When you select a rating and set it to

“BLOCK”, the higher ratings will be blocked

automatically. The lower ratings will be avail-

able for viewing.

•

When you set the lowest rating to “VIEW”, all

other ratings will automatically be available

for viewing.

5 When you select the ratings of TV-Y7, TV-PG,

TV-14 or TV-MA you will have the option of

setting sub rating categories.

Press [K] or [L] to select a rating with sub-

ratings you wish to block, then press

[ENTER] twice.

Press [K] or [L] to select a sub-rating, then

press [ENTER] to set it to “BLOCK” or “VIEW”.

•

The blocked sub-ratings will appear next to

the rating category in the “TV RATING”

menu.

- 16 - EN

– V-CHIP SET UP –

B TV RATING

MPAA RATING

CHANGE CODE

ENTER

B TV–Y [VIEW]

TV–Y7 ( ) [VIEW]

TV–G [VIEW]

TV–PG ( ) [VIEW]

TV–14 ( ) [VIEW]

TV–MA ( ) [VIEW]

Selection Rating Category Explanations

TV-Y Appropriate for all children

TV-Y7 Appropriate for children seven and older

TV-G General Audience

TV-PG Parental Guidance suggested.

TV-14 Unsuitable for children under 14

TV-MA Mature audience only

TV–Y [VIEW]

TV–Y7 ( ) [VIEW]

B TV–G [BLOCK]

TV–PG (DLSV ) [BLOCK]

TV–14 (DLSV) [BLOCK]

TV–MA ( LSV) [BLOCK]

Selection Rating Category Explanations

TV-Y7

FV Fantasy Violence

TV-PG, TV-14, TV-MA

D Suggestive Dialog

(TV-PG, TV-14 only)

L Coarse Language

S Sexual Situation

VViolence

- 16 - EN

V-CHIP SET UP

REV

SLOW

PLAY

STOP

FWD

ENTER

PAUSE

DISC

RETURNTITLESETUP

DISPLAY

SKIP

CH.

VOL.

MUTEZOOM

SLEEP

123

456

789

0 +10

+100

SETUP

- TV SET UP -

CHANNEL SET UP

B V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

BACK LIGHT [BRIGHT]

ENTER

ACCESS CODE

_ _ _ _

123

456

789

NOTE

- 17 - EN- 17 - EN- 17 - EN- 17 - EN- 17 - EN- 17 - EN

6 Press [SETUP] to exit the menu.

•

To change the rating, the TV must be turned

to an unprotected program. If “PROTECT-

ED PROGRAM by ...” appears on the

screen, please change the channel to a station

that is not protected.

MPAA RATING SET UP

Follow steps

in the V-CHIP SET UP on page

16.

4 Press [K] or [L] to point to your desired item,

then press [ENTER] to select “BLOCK” or

“VIEW”.

•

When you select a rating and set it to “BLOCK”,

the higher ratings will be blocked automatically.

The lower ratings will be available for viewing.

•

When you set the lowest rating to “VIEW”, all other

ratings will automatically be available for viewing.

5 Press [SETUP] to exit the menu.

CHANGE ACCESS CODE

Follow steps

in the V-CHIP SET UP on page

16.

4 Press the number buttons to enter your

desired access code in the “NEW CODE”

space, then enter the same code in the

“CONFIRM CODE” space. When completed,

the menu will return to “V-CHIP SET UP”.

•

Make sure you enter exactly the same new code

in the “CONFIRM CODE” space as one in the

“NEW CODE” space. If they are different, the

“NEW CODE” space is cleared for redoing.

5 Press [SETUP] to exit the menu.

•

Your personal access code will be erased and

will return to the default (0000) when a

power failure occurs or when you turn off the

power using a wall switch. If you have for-

gotten the code, unplug the power cord for 10

seconds to restore the access code to 0000.

1 Press [SETUP] then press [K] or [L] to point

to “LANGUAGE”.

2 Press [ENTER] repeatedly to select

“ENGLISH”, “ESPAÑOL”= Spanish or

“FRANÇAIS”= French.

3 Press [SETUP] to exit the menu.

•

This function effects only the language on the

screen menu and not the audio source.

•

If for some reason the menu is in Spanish or

French, press [SETUP], press [K] or [L] to

point to “IDIOMA [ESPAÑOL]” or “LAN-

GAGE [FRANÇAIS]”, then press [ENTER]

repeatedly to select desired language, then

press [SETUP].

G [VIEW]

PG [VIEW]

PG–13 [VIEW]

B R [BLOCK]

NC–17 [BLOCK]

X [BLOCK]

TV SECTION

TV OPERATION AND SETTINGS

SETUP

NOTE

Selection Rating Category Explanations

G General Audience

PG Parental Guidance suggested.

PG-13 Unsuitable for children under 13

R Restricted; under 17 requires accompa-

nying parent or adult guardian

NC-17 No one under 17 admitted

X Mature audience only

SETUP

NEW CODE

X X X X

CONFIRM CODE

_ _ _ _

- TV SET UP -

CHANNEL SET UP

V-CHIP SET UP

B LANGUAGE [ENGLISH]

CAPTION [OFF]

BACK LIGHT [BRIGHT]

123

456

789

SETUP

ENTER

SETUP

NOTE

MENU LANGUAGE

NOTE

–

•

NEVER play back the following discs. Otherwise, the unit may result in malfunction.

DVD-RAM / CD-I / Photo CD / Video CD / DVD with region codes other than 1 or ALL /

DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers

•

Never insert a disc which is broken or whose form is abnormal (other than 5 inch (12cm) round disc).

•

On the following disc, the sound MAY NOT be heard.

Super Audio CD

Only the sound recorded on the normal CD layer can be delivered.

The sound recorded on the high density Super Audio CD layer cannot be delivered.

•

Any other discs without compatibility indications

UNPLAYABLE DISCS

If you cannot play back a disc which bears one of the marks above, check the following notes.

*1:

This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot be played back.

*2:

Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.

*3: Discs recorded in the VR (Video Recording) format cannot be played back.

*4: Scratched or stained discs may not be played back.

*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the

recorder or special properties of discs.

*6: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not

play them back. Even if they are played back, the sound or video quality will be compromised.

*7:

You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD recorder. However, depend-

ing on the recording status of a disc, the disc may not be played back at all or normally (the picture or sound may not be smooth,

etc.). In this case, you need to finalize the disc with the DVD recorder. Refer to the manual accompanying the DVD recorder.

*8: Only the discs recorded in the video format and finalized can be played back.

Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be

played back at all or normally (the picture or sound may not be smooth, etc.).

*9:

If there is too much recording space left on a disc (the used portion is less than 2-

" (55mm) across), it may not play back properly.

*10:

Do not glue paper or put stickers on to the disc. These may damage the disc and the unit may not read it correctly.

*11: The number inside the symbol refers to a region of the world and a disc encoded in a specific region for-

mat can only be played back on unit with the same region code.

PLAYABLE DISCS

is a trademark of DVD Format/Logo Licensing Corporation.

ABOUT THE DISCS

DVD SECTION

NOTE

Example

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1 Chapter 2Chapter 3 Chapter 4

MP3

Example

Group 1 Group 2

Trac k 1 Track 2Track 5Track 6Trac k 3 Track 4

Example

Trac k 1 Track 2Track 5Track 6Trac k 3 Track 4

Audio CD

Digital video

(MPEG2)

Digital audio

MP3

5 inches

(12cm)

5 inches

(12cm)

DVD-Video

* 1,2,4,6,10,11

* 1,3,4,5,

6,8,9,10

* 1,3,4,5,

6,7,9,10

* 4,6,10

* 4,5,6,9,10

DVD-RW

DVD-R

DVD+RW

DVD+R

Audio CD

CD-RW

CD-R

Region code

Mark (logo)

Playable

discs

Recorded

signals

Disc size Disc type

–

•

Shaded buttons are used for following operation.

GETTING STARTED

Turn on the power of amplifier and any other compo-

nents, if necessary.

1 Press [POWER] then the power will turn on.

2 Open the disc door manually.

Insert a disc with the label facing back of the unit to

start playing it. By simply placing the disc gently into

the slot, it will be loaded automatically.

•

Playback will start from the first chapter/track of the disc.

•

If the playback does not start automatically,

press

[PLAY O].

•

When you playback a DVD which features a

title menu, it may appear on the screen. In this

case, refer to “TITLE MENU” on page 20.

4 Press [STOP C] to stop playback.

Press [EJECT

] to remove the disc from the unit.

•

When the DVD mode has been switched to the

TV mode, the DVD mode shuts down first and

then the TV picture and sound appears in about

4 seconds. Similarly, when [POWER] is press

to turn off in the DVD mode, this mode shuts

down first and then the unit is turned off.

•

“” may appear at the top-right on the TV

screen during operation, warning that a pro-

hibited operation has been encountered by the

DVD or the disc.

•

With DVDs that use titles for playback pro-

gram signals, playback may start from the

second title or it may skip these titles.

•

During the playback of a two layered disc,

pictures may stop for a moment. This happens

when the 1st layer switches to the 2nd layer.

This is not a malfunction.

MP3 PLAYBACK

1 In stop mode, press [DISC MENU], then press

[

] or [

] to select the desired group or track.

•

If a group is selected, press [B] or [ENTER] to go

on to the track selection screen. Press [s] to go

back to previous screen.(except for the top page.)

•

If a track is selected, press [ENTER] to start

playing tracks. Starting from the one you’ve just

chosen the subsequent tracks will be played.

•

If the entire file list cannot be displayed at once

on a screen, “n” appears to go to the next page.

•

Press [TITLE] to return to the top file of the

highest hierarchy in the program and file list.

2 Press [STOP

] to stop playback.

•

Folders are known as Groups; files are known as Tracks.

•

MP3 files are accompanied by icon.

•

Maximum of 255 folders can

be recognized.

•

Maximum of 999 files can be recognized.

•

Up to 8 hierarchies can be created.

This unit recommends the use of files recorded

at the below specifications:

•

Sampling frequency: 44.1kHz or 48kHz

•

Constant bit rate: 32kbps ~ 320kbps

•

For MP3 file recorded in Variable Bit Rate (VBR),

the unit may not display the actual elapsed time.

PLAYING A DISC

DVD SECTION

ABOUT THE DISCS / PLAYING A DISC

BASIC PLAYBACK

REV

SLOW

PLAY

STOP

FWD

ENTER

PAUSE

DISC

RETURNTITLESETUP

A B

REPEATSEARCH MODE

CLEAR

DISPLAY

SKIP

MUTEZOOM

SLEEP

0 +10

SELECT

POWER

PICTURE EJECT

POWER

STOP

EJECT

NOTE

folder name 1

folder name 2

folder name 3

folder name 4

file name 1

file name 2

file name 3

folder name 1

DISC

STOP

NOTE

1 Press [DISC MENU].

•

The DVD main menu will appear.

•

If the feature is not available, symbol may

appear on the TV screen.

•

If disc menu is available on the disc, audio lan-

guage, subtitle options, chapters for the title and

other options will appear for selection.

2 Press [K], [L], [s] or [B] to select an item

and press [ENTER] to confirm selection.

1 Press [TITLE].

•

The title menu will appear.

•

If the feature is not available, symbol may

appear on the TV screen.

2 Press [K], [L], [s] or [B] to select an item

then press [ENTER] to confirm selection.

CALLING UP A MENU SCREEN

DURING PLAYBACK

Press [DISC MENU] to call up the DVD menu or

press

[TITLE] to call up the title menu.

•

Contents of menu and corresponding menu

operations may vary between discs. Refer to

the manual accompanying the disc for details.

1 During playback, press [STOP C].

(Example: DVD or Audio CD)

•

Resume message will appear on the TV screen.

2 Press [PLAY O], playback will resume from

the point at which playback was stopped.

•

To cancel resume, press [STOP C] twice.

•

For MP3, playback will resume from the begin-

ning of the current track.

•

The resume information stays on even when the

power is turned off.

1 During playback, press [PAUSE F].

•

Playback will pause and sound will be muted.

2 To continue playback, press [PLAY O].

1 During playback, press [PAUSE F].

•

Playback will pause and sound will be muted.

2 The disc goes forward by one frame each

time [PAUSE F] is pressed.

To exit step by step playback, press [PLAY O].

RESUME

PAUSE

–

TITLE MENU

DISC MENU

DISC

ENTER

TITLE

ENTER

STOP

PLAY

PAUSE

STEP BY STEP PLAYBACK

PAUSE

PLAY

NOTE

Press ’PLAY’ to play from here.

To play the beginning,

press ’STOP’ first and then ’PLAY’.

Resume ON

1 During playback, press [FWD

] or

[REV

•

“

1” or “

1” appears on the screen.

2 To select another speed, repeat step 1 until

your required speed number appears on the

screen.

•

For DVDs, fast forward/reverse search speed is

different depending on the disc. Approximate

speed is 1 (×2), 2 (×8), 3 (×20), 4 (×50) and

5 (×100).

•

For Audio CDs and MP3 approximate speed is

1 (×2), 2 (×8) and 3 (×30).

To return to normal playback, press [PLAY O].

1 During playback, press [PAUSE F].

2 Press [FWD

] or [REV

•

“1”or “1”appears on the screen.

3 To select another speed, repeat step 2 until

your required speed number appears on the

screen.

•

Slow forward or reverse speed varies with the

disc. Approximate speed is 1 (1/16), 2 (1/8) and

3 (1/2).

To return to normal playback, press [PLAY O].

The Zoom function allows you to enlarge the video

image and to pan through the enlarged image.

1 Press [ZOOM] during playback.

•

Playback will continue.

2 Press [ZOOM] repeatedly to select the

required zoom factor: ZOOM1, ZOOM2,

ZOOM3 or OFF.

3 Press [K], [L], [s] or [B] to move the

zoomed picture across the screen.

4 To exit zoom mode, press [ZOOM] to OFF.

•

Zooming function does not work while disc

menu is shown.

•

Zooming function is not available on some

discs.

•

It may take several seconds to slide the

zoomed picture.

•

The picture may be distorted if you operate

other functions repeatedly (ex. [PAUSE

] or

[REV

], etc.) in the zoom mode.

FAST FORWARD /

FAST REVERSE

SLOW FORWARD /

SLOW REVERSE

ZOOM

REV

SLOW

FWD

PLAY

PAUSE

REV

SLOW

FWD

PLAY

ZOOM

DVD SECTION

PLAYING A DISC

ZOOM

NOTE

–

•

Shaded buttons are used for following operation.

There are three ways to begin playback on an Audio

CD and MP3 at a specific track.

Using the number buttons

1 Press the Number buttons to enter the

desired track number.

•

Playback will start at the selected track.

•

To select single-digit track number, press single

number. (e.g. Press [3] for track number 3.)

•

To select track numbers which are higher than 9,

press

[+100/+10] first.

(e.g. Press [+100/+10] [2] [5] for track number

25.)

Using [SEARCH MODE]

1 Press [SEARCH MODE].

•

The track search display appears.

2 Within 30 seconds, select the desired track

number using the Number buttons.

•

To select single-digit track number, press [0]

first if the total number of track in the disc is 10

or more. (e.g. Press [0] [3] for track number 3.)

•

Playback will start at the selected track.

Using [SKIP

]

During playback, press [SKIP G] to move the next

track. Press it repeatedly to skip subsequent tracks.

Press [SKIP H] to go back to beginning of the cur-

rent track. Press it repeatedly to go to the previous

tracks.

•

If [SKIP H / G] is pressed while the play-

back is paused, the playback will be paused

again after skipping to the next track.

•

[SKIP H / G ] are not operative when

playback is stopped.

1 Press [SEARCH MODE] once for the Chapter

search, twice for the Title search during play-

back.

2 Within 30 seconds, enter the desired chapter/

title number using the Number buttons.

•

Playback will start at the selected chapter or

title.

•

Press [CLEAR] to erase the incorrect input.

•

To select single-digit chapter/title number, press

[0] first if the total number of chapter/title in the

disc 10 or more. (e.g. Press

[0] [2] for

chapter/title 2.)

TRACK SEARCH

TITLE / CHAPTER SEARCH

_/2

SEARCH FUNCTION

REV

SLOW

PLAY

STOP

FWD

ENTER

PAUSE

DISC

RETURNTITLESETUP

REPEATSEARCH MODE

CLEAR

DISPLAY

SKIP

CH.

VOL.

MUTEZOOM

SLEEP

123

456

789

0 +10

+100

123

456

789

0 +10

+100

SEARCH MODE

123

456

789

once

SEARCH MODE

123

456

789

NOTE

–

1 During playback, press [SEARCH MODE]

repeatedly to display the Time Search on the

TV screen.

2 Within 30 seconds, enter a desired disc time

using the Number buttons.

•

Playback will start at the specified time.

•

Press [CLEAR] to erase the incorrect input.

•

When there is no need to enter a number, “0”

appears automatically. For example,

“0 : 0

- -

” appears in the Time Search display

if the total time of the track or title is less than

10 minutes.

Use markers to memorize your favorite places on a disc.

1 Press [SEARCH MODE] repeatedly during

playback to display the Marker screen.

2 Press [s ] or [B] to select 1, 2, 3, 4, 5, 6, 7,

8, 9, or 10 and ensure that “

- - - -

- -

”

appears in the display.

3 When you reach the desired point, press

[ENTER].

•

The Title or Track and elapsed playing time will

appear in the TV screen.

4 To return to the Marker later, press [SEARCH

MODE] repeatedly during playback to display

the Marker screen. Then press [s] or [B] to

choose the desired marker, then press

[ENTER].

•

Operations which erase all Markers:

– Turning off the power.

– Ejecting a disc from the unit.

– Pressing [SELECT].

–

Selecting “AC” at step 2 and pressing

[ENTER].

•

To clear a marker:

– Press [s ] or [B] to select a cursor on to the

marker number and press [CLEAR].

•

You can mark up to 10 points.

5 Press [SEARCH MODE] or [RETURN] to

exit.

TIME SEARCH MARKER SETUP SCREEN

SEARCH MODE

repeatedly

123

456

789

SEARCH MODE

repeatedlly

ENTER

repeatedly

SEARCH MODE

ENTER

SEARCH MODE

DVD SECTION

SEARCH FUNCTION

NOTE

_:_ _:_ _ 1:29:00

TOTAL

_ _ _

_:_ _:_ _

21 345678910 AC

•

Shaded buttons are used for following operation.

REPEAT is available only during playback.

For DVD-Vs

1 To activate the repeat function, press

[REPEAT] during playback.

•

The repeat mode changes as described below

every time you press the button.

•

Repeat Title/Chapter is not available with

some scenes.

•

Repeat setting will be cleared when moving

to other title or chapter.

For CDs

1 To activate the repeat function, press

[REPEAT] during playback.

•

The repeat mode changes as described below

every time you press the button.

•

Repeat Track setting will be cleared when

moving to other track.

•

Repeat playback does not function during A-

B repeat playback.

For MP3

1 Press [REPEAT] during playback.

•

The repeat mode changes as described below

every time you press the button.

•

Repeat Track/Group setting will be cleared

when moving to other track or group.

1 Press [A-B] at your chosen starting point.

•

“A-”appears briefly on the TV screen.

2 Press [A-B] again at your chosen end point.

•

“ A-B” appears briefly on the TV screen, and

the repeat sequence begins.

3 To exit the sequence, press [A-B].

•

The A-B repeat section can only be set within

the current title (for DVDs) or current track

(for Audio CDs).

•

A-B repeat is not available with some scenes in DVD.

•

To cancel the A point which was set, press

[CLEAR].

•

A-B repeat playback does not function during

title, chapter, track or all repeat playback.

–

SPECIAL PLAYBACK FUNCTION

REPEAT

A-B REPEAT

CHAPTER TITLE OFF

(current chapter repeat) (current title repeat)

(repeat

off)

TRACK ALL OFF

(current track repeat) (entire disc repeat)

(repeat

off)

REV

SLOW

PLAY

STOP

FWD

ENTER

PAUSE

DISC

RETURNTITLESETUP

REPEATSEARCH MODE

CLEAR

MODE

DISPLAY

ANGLESUBTITLEAUDIO

REPEAT

NOTE

TRACK

ALL OFF

(current track

repeat)

(entire disc

repeat)

(repeat

off)

GROUP

(current group

repeat)

REPEAT

NOTE

–

DVD SECTION

SPECIAL PLAYBACK FUNCTION

You may determine the order in which tracks will play.

1 In stop mode, press [MODE].

•

The “PROGRAM” screen will appear.

2 Press [▲ ] or [▼] to select a track, then press

[ENTER].

•

Press [CLEAR] to erase the most recently

entered track.

•

If the entire Program cannot be displayed at

once on a screen, “G” appears to go to the next

page and “H” appears to go back to the previ-

ous page.

While an MP3 folder is open:

•

Press [B] when you want to go to the next

hierarchy.

•

Press [s] when you want to go back to the

previous hierarchy.

3 Repeat step 2 until you have selected all the

tracks you want to play in the program.

Press [PLAY O] to play the programmed tracks.

•

While the program is being played back,

pressing [STOP C] works as follows.

•

Press [STOP C] once and then [PLAY O]

again, playback will restart from the point where

[STOP C] was pressed (MP3: from the begin-

ning of the current track). (Program continued)

•

Press [STOP C] twice and then [PLAY O]

again, playback will restart from the track in

the usual way. (Program canceled)

•

Up to 99 tracks can be entered.

•

To erase all tracks in the program at once, select

“ALL CLEAR” at the bottom of the list at step 2.

•

If you like to repeat the current track in the

program, press [REPEAT] several times until

“ TRACK” appears during playback. If you

like to repeat the entire program press

[REPEAT] several times until “ ALL”

appears during playback.

This function shuffles the playing order of tracks

instead of playback in the sequence.

1 In stop mode, press [MODE] twice.

•

“RANDOM” screen appears.

2 Press [PLAY O] to start random playback.

•

If you like to repeat the current track in the ran-

dom selection, press [REPEAT] several times

until “ TRACK” appears during playback. If

you like to repeat the entire random selection

press [REPEAT] several times until “ ALL”

appears during playback.

PROGRAM

MODE

ENTER

TOTAL

1/4 2/3

1 3:30

5 5:10

10 4:20

11 3:00

12 3:20

17 4:10

22 2:50

1:03:30

PLAY

NOTE

RANDOM PLAYBACK

twice

MODE

PLAY

CD-DA TOTAL 0:45:55

RANDOM PROGRAM

- - no indication - -

RANDOM

PLAY

NOTE

–

•

Shaded buttons are used for following operation.

The unit allows you to select a language for subtitles

during DVD disc (if available) playback.

1 Press [SUBTITLE] during playback.

•

The subtitle language will appear on the display

bar at the top of the TV screen.

2 Press [SUBTITLE] repeatedly to select your

desired subtitle language.

3 To turn off subtitles, press [SUBTITLE]

repeatedly until “OFF” appears.

•

Pressing [SUBTITLE] may not work on

some DVDs with multiple subtitle languages.

In this case, set it on the disc menu.

(Operation varies between discs Refer to the

manual of the disc.)

•

If the desired language is not shown after

pressing [SUBTITLE] several times, the disc

does not have subtitles in that language.

•

When “NOT AVAILABLE” appears on the TV

screen, it means no subtitle is recorded on the

scene.

•

If you choose a language that has a 3 letter

language code, the code will be displayed

every time you change the Subtitle language

setting. If you choose any other languages,

“---” will be displayed instead. (Refer to page

29.)

The unit allows you to select a language during DVD

disc (if multi languages are available) playback.

1 Press [AUDIO] during playback.

2 Press [AUDIO] repeatedly to select your

desired language.

•

Pressing [AUDIO] may not work on some

DVDs with multiple audio languages (e.g.

DVDs which allow audio language setting on

the disc menu).

Press [AUDIO] repeatedly during playback to

select between “STEREO”, “L-ch” or “R-ch”.

•

STEREO - both right and left channels are

active (stereo)

L-ch - only left channel is active

R-ch - only right channel is active

AUDIO LANGUAGE

SUBTITLE LANGUAGE

1.ENG/6

1.ENG Dolby D 3/2.1ch 48k/3

NOT AVAILABLE

CHANGING THE SETTINGS

STEREO SOUND MODE

STEREO

ENTER

RETURNTITLESETUP

REPEATSEARCH MODE

CLEAR

MODE

DISPLAY

ANGLESUBTITLEAUDIO

SUBTITLE

AUDIO

NOTE

–

Some DVD discs contain scenes which have been shot

simultaneously from various angles. You can change

the camera angle when the “”icon appears on the

screen.

1 Press [ANGLE] during playback.

•

The selected angle will be displayed on the dis-

play bar at the top of the screen.

•

If the “ANGLE ICON” setting is “OFF” in the

“OTHERS” menu, the “”icon will not

appear. (Refer to page 31.)

2 Press [ANGLE] repeatedly to select your

desired angle.

Adjust the Black Level Settings to make the black

parts of the picture brighter.

1 Press [MODE] during playback then press

[ENTER] to switch “ON” or “OFF”.

ON: Makes the dark parts brighter.

OFF: Shows the original picture as recorded.

(Initial setting)

2 Press [MODE] twice or [RETURN] to exit.

•

The setting will be saved even if the unit is

turned off.

You can enjoy surround-sound effect over two speak-

ers on this unit.

1 Press [MODE] repeatedly during playback

then press [ENTER] to set it “1”, “2” or “OFF”.

1: Natural effect

2: Emphasized effect

OFF: Original Sound

2 Press [MODE] to exit.

•

You can also exit the menu by pressing

[RETURN].

For CD play only:

•

Virtual Surround will not be effective if the

sound mode is set to something other than

STEREO. (Refer to “STEREO SOUND

MODE” on pge 26.)

VIRTUAL SURROUND

OFF

BLACK LEVEL SETTING

OFF

CAMERA ANGLE

1 / 8

ANGLE

MODE

twice OR

MODE

RETURN

twice

MODE

ENTER

MODE

DVD SECTION

CHANGING THE SETTINGS

NOTE

–

•

Shaded buttons are used for following operation.

You can check the information about the current disc

by pressing

[DISPLAY].

For DVD-Vs

1 Press [DISPLAY] during playback to show

current Chapter.

Press [DISPLAY] again to show current Title.

3 Press [DISPLAY] again.

4 Press [DISPLAY] again to exit.

For Audio CDs

1 Press [DISPLAY] during playback to show the

current Track.

2 Press [DISPLAY] again to show current Total

Track .

3 Press [DISPLAY] again to exit.

•

When you are playing a disc in PROGRAM

or RANDOM mode, “ PROGRAM” (or

RANDOM) will be displayed at step 2.

For MP3

1 Press [DISPLAY] during playback.

2 Press [DISPLAY] again.

3 Press [DISPLAY] again to show the current-

playback mode.

(Only when you are playing a disc in PROGRAM or

RANDOM mode.)

4 Press [DISPLAY] again to exit.

THE ON-SCREEN INFORMATION

PROGRAM

RANDOM

ENTER

RETURNTITLESETUP

DISPLAY

CH(Chapter):

Current chapter number / Total chapters

11/16 0:00:00 - 0:03:30

Elapsed time of the current chapter

Remaining time of the current chapter

Current playback status

Angle icon, appears only when avail-

able on the DVD

TT(Title):

Current title number / Total titles

1/3 0:00:00 - 1:23:45

Elapsed time of the current title

Remaining time of the current title

Current repeat setting appears only

when the repeat setting is active

C: Chapter repeat / T: Title repeat /

AB:A-B repeat

TL1

BIT RATE: The amount of audio and

video data currently being read

Layer numbers, appears only when

playing a two-layered Disc

L0: Layer 0 is playing

L1: Layer 1 is playing

4/12 0:03:21 - 0:02:15

TR(Track):

Current track number / Total tracks

Elapsed time of the current track

Remaining time of the current track

Current playback status

4/12 0:13:45 - 0:45:40

Current repeat setting appears only

when the repeat setting is active

T: Tr ack repeat

A: All Tracks repeat

AB:A-B repeat

ALL:

Current track number / Total tracks

Elapsed time of the entire disc

Remaining time of the entire disc

TRACK 01

The name of the file currently in play

will be displayed.

Current playback status

1/36 0:01:15

Current repeat setting, if active

T: Tr ack repeat

G: Group (folder) repeat

A: Disc repeat

Elapsed playing time of the current

track

TR(Track):

Current track number / Total tracks

–

•

Shaded buttons are used for following operation.

You can change the DVD player’s settings.

1 In stop mode, press [SETUP] twice, [L] to

select “CUSTOM” then press [ENTER].

•

If the menu does not appear, press [PLAY O]

first, then press [STOP C]. Make sure the

disc is in stop mode, then slowly press

[SETUP] twice.

2 Press [K] or [L] to select the desired item

then press [ENTER] to confirm.

Refer to the pages below to set up each item.

LANGUAGE: See LANGUAGE SETTING

DISPLAY: See DISPLAY SETTING

AUDIO: See AUDIO SETTINGS

PARENTAL: See

PARENTAL CONTROL

OTHERS: See OTHER SETTINGS

LANGUAGE SETTING

Follow steps

in the .

3 Press [K] or [L] to select the desired item

then press [ENTER].

AUDIO: Sets the audio language.

SUBTITLE: Sets the subtitle language

DISC MENU: Sets the language for DVD menu.

4 Press [K] or [L] to select a setting then press

[ENTER].

•

If “OTHER” is selected on the “AUDIO”, “SUB-

TITLE” or “DISC MENU” screen, press four-

digit number to enter the code for the desired

language.

•

Only the languages supported by the disc can be

selected.

5 Press [SETUP] to exit the menu.

•

Language Setting for Audio and Subtitle are

not valid for some discs due to default setting

of the disc. In this case, set them by pressing

[AUDIO] and [SUBTITLE]. (Refer to page

26.)

•

If you select a language that is not supported

by the disc, subtitle will automatically be set

OFF and the first item of the audio languages

will be automatically set.

CUSTOM MENU

SUBTITLE

OFF

ENGLISH

FRENCH

SETUP LANGUAGE

DISC MENU

ENGLISH

FRENCH

SPANISH

SETUP LANGUAGE

AUDIO

ORIGINAL

ENGLISH

FRENCH

SETUP LANGUAGE

AUDIO

SUBTITLE

DISC MENU

ORIGINAL

OFF

ENGLISH

CHANGING THE DVD SET UP ITEMS

CUSTOM MENU

SETUP

QUICK

CUSTOM

INITIALIZE

ENTER

PAUSE

RETURNTITLESETUP

REPEATSEARCH MODE

CLEAR

DISPLAY

twice

SETUP

ENTER

SETUP CUSTOM

LANGUAGE

DISPLAY

AUDIO

PARENTAL

OTHERS

ENTER

SETUP

DVD SECTION

THE ON-SCREEN INFORMATION / CHANGING THE DVD SET UP ITEMS

NOTE

–

DISPLAY SETTING

Follow steps

in the on

page 29.

3 Press [K] or [L] to select the below items then

press [ENTER].

TV MODE:

You can change certain aspects of the DVD display

screens and on-screen messages on the TV screen.

•

4:3 LETTER BOX (default): To show black bars

on top and bottom of the screen.

•

4:3 PAN & SCAN: To show a full height picture

with both sides trimmed.

STILL MODE

This function allows you to adjust picture resolu-

tion and quality in the still mode.

•

AUTO (default): Automatically select the best

resolution setting (FRAME or FIELD) based on

the data characteristics of the pictures.

•

FIELD: Select “FIELD” when the pictures are

still unstable even if “AUTO” is selected.

FIELD stabilizes the pictures, although the pic-

ture quality may become coarse due to the limit-

ed amount of data.

•

FRAME: Select “FRAME” to display relatively

motionless pictures in higher resolution.

FRAME improves the picture quality, although it

may unstabilizethe pictures due to simultaneous

output of two field data.

4 Press [SETUP] to exit the menu.

AUDIO SETTING

Choose the appropriate Audio settings for your equip-

ment as it only affects during the playback of DVD

discs.

Follow steps

in the on

page 29.

3 Press [K] or [L] to select the below items then

press [ENTER].

DRC (Dynamic Range Control):

•

To compress the range of soft to loud sound.

•

The default setting is “ON”.

DOWN SAMPLING:

•

ON : Output in 48 kHz. (default)

•

OFF : Output the original sound.

When playing disc with copyright Protection

•

If you select “OFF”, copyright protection will be

activated and sound will be down sampled at

48kHz.

DOLBY DIGITAL:

Set to “BITSTREAM” when the unit is connected

to a Dolby Digital Decoder.

•

BITSTREAM: Output a Dolby Digital signal

(default)

•

PCM: Convert the Dolby Digital to PCM

(2 channel stereo)

4 Press [SETUP] to exit the menu.

QUICK

CUSTOM MENU

QUICK

CUSTOM MENU

TV MODE

4:3 LETTER BOX

STILL MODE

AUTO

SETUP DISPLAY

TV MODE

4:3 LETTER BOX

STILL MODE

AUTO

SETUP DISPLAY

ENTER

TV MODE

4:3 LETTER BOX

STILL MODE

AUTO

SETUP DISPLAY

SETUP

DRC ON

DOWN SAMPLING

DOLBY DIGITAL BITSTREAM

SETUP AUDIO

DRC ON

DOWN SAMPLING

DOLBY DIGITAL BITSTREAM

SETUP AUDIO

DRC ON

DOWN SAMPLING

DOLBY DIGITAL BITSTREAM

SETUP AUDIO

DRC ON

DOWN SAMPLING

DOLBY DIGITAL BITSTREAM

SETUP AUDIO

ENTER

SETUP

TV SET UP MENU IN DVD MODE

•

You can access the TV SETUP menu by pressing [SETUP] from the DVD mode, and select only

“LANGUAGE” and “BACK LIGHT”.

QUICK MENU

•

You can select the “TV MODE” or “DOLBY DIGITAL” from the QUICK menu quickly. To access the

QUICK menu, select “QUICK” instead of “CUSTOM” at step

on page 29.

–

PARENTAL CONTROL

Parental Control limits the disc viewing that exceed

your setting (with a password or playback will stop).

This feature allows you to prevent discs with alterna-

tive scenes from being played by your children.

PARENTAL LEVEL

Parental Level allows you to set the rating level of

your DVD discs. Playback will stop if the disc’s rat-

ings exceed the level you set.

Follow steps

in the on

page 29.

3 Enter your four-digit password then press

[ENTER].

•

Press [4], [7], [3], [7] then enter your password

if you forget the password.

4 Press [K] or [L] to select “PARENTAL LEVEL”

then press [ENTER].

5 Press [K] or [L] to select the desired level

then press [ENTER].

6 Press [SETUP] to exit the menu.

•

When doing this for the first time, enter any 4

digits. (except for 4737) That number will be

used as the password. (in the event you forget

the password, see below)

•

To change the password, press [K] or [L] to

select “PASSWORD CHANGE” at step 4

then press [ENTER]. Enter the four-digit

password, then press [ENTER].

•

With some DVDs, it may be difficult to find

if they are compatible with parental lock. Be

sure to check if the parental lock function

operates in the way that you have set.

•

Record the password in case you forget it.

CONTROL LEVELS

•

ALL

All parental lock is cancelled.

•

Level 8

DVD software of any grade (adult/general/children)

can be played back.

•

Levels 7 to 2

Only DVD software intended for general use and

children can be played back.

•

Level 1

Only DVD software intended for children can be

played back, with those intended for adult and gen-

eral use prohibited.

OTHER SETTINGS

Follow steps

in the on

page 29.

3 Press [K] or [L] to select the below items then

press [ENTER].

ANGLE ICON:

•

Press [ENTER] repeatedly to turn Angle icon

“ON” or “OFF”.

•

The default setting is “ON”.

SCREEN SAVER:

•

Press [ENTER] repeatedly to turn Screen Saver

“ON” or “OFF”.

•

The default setting is “OFF”. If you select “ON”,

the screen saver program starts when there is no

input from the unit for 5 minutes in stop mode.

4 Press [SETUP] to exit the menu.

CUSTOM MENU

SETUP PARENTAL

PASSWORD

Enter current password.

PASSWORD CHANGE

PARENTAL LEVEL ALL

SETUP PARENTAL

PARENTAL LEVEL

ALL

7 [NC-17]

6 [R]

SETUP PARENTAL

SETUP OTHERS

ANGLE ICON

SCREEN SAVER

OFF

123

456

789

ENTER

SETUP

ENTER

SETUP

NOTE

DVD SECTION

CHANGING THE DVD SET UP ITEMS

–

•

Shaded buttons are used for following operation.

This allows you to return all selections of SETUP

(except for “PARENTAL” and menu language) to

their default settings.

1 Press [SETUP] twice in stop mode so that the

“INITIALIZE” menu appears.

2 Press [K] or [L] to select “INITIALIZE” then

press [ENTER].

3 Press [K] or [L] to select “YES” then press

[ENTER] twice.

All the settings (except for “PARENTAL” and

menu language) will be cleared.

•

To cancel the initialization, select “NO”.

4 Press [SETUP] to exit the menu.

–

INITIALIZE

SETUP

QUICK

CUSTOM

INITIALIZE

SETUP INITIALIZE

Initialize?

YES

ENTER

PAUSE

RETURNTITLESETUP

DISPLAY

SETUP

ENTER

twice

ENTER

SETUP

–

Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked

possibilities. Before arranging for service, check these items. It could save your time and money.

TV Mode

PROBLEM CORRECTIVE ACTION

No picture or sound

•

Make sure the AC cord is connected to an AC outlet.

•

Check antenna connection.

•

Press [SELECT] to select TV mode.

Then try other TV feature.

•

Let the unit program its tuner memory.

No picture or poor picture on the

•

Adjust direction or replace antenna.

unit

•

Adjust picture controls.

•

Check for broken pin of the antenna cable.

No sound or poor sound

•

Adjust volume control on remote control or main unit.

•

Press [MUTE] to restore sound.

Bars On Screen

•

If outside antenna is being used, check for broken wire.

•

Check for local interference.

Picture Distorted or Blurred

•

Try a new channel, if OK, then possible station trouble.

•

If outside antenna is being used, check for broken wire.

Picture Rolls Vertically

•

Try a new channel, if OK, then possible station trouble.

Lines or Streaks in Picture

•

If outside antenna is being used, check for broken wire.

•

Check for local interference.

No Color

•

Try a new channel, if OK, then possible station trouble.

•

Is antenna connected to jack on the back of the set?

•

If outside antenna is being used, check for broken wire.

•

Adjust “COLOR” control.

Poor Reception on Some Channels

•

Try a new channel, if OK, then possible station trouble.

Ghosts in Picture

•

Is antenna connected to jack on the back of the set?

•

If outside antenna is being used, check for broken wire.

•

Check for local interference.

Weak Picture

•

Try a new channel, if OK, then possible station trouble.

•

Is antenna connected to jack on the back of the set?

•

If outside antenna is being used, check for broken wire.

•

Adjust “CONTRAST” & “BRIGHT” control.

If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit, con-

sulting the following checklist.

PROBLEM CORRECTIVE ACTION

No power

•

Make sure the power plug is connected to an AC outlet.

•

Make sure the power is turned on.

No operation by infrared remote

•

Check if the power plug is connected to an AC outlet.

control

•

Check the batteries in the remote control.

•

Aim the remote control directly at the remote sensor. If necessary,

remove all the obstacles between the sensor and the remote control.

•

You have to be within 23 feet of the unit.

•

Check if the correct mode is selected. If not switch the mode by

pressing

[SELECT], whichever you need.

TROUBLESHOOTING GUIDE

–

CLOSED CAPTION PROBLEM POSSIBLE REMEDY

Misspelling in captions • Error committed by the closed captioning production company.

• Possible in a live broadcast. Not in case of a prerecorded program.

Text is not shown in its entirety or • A few seconds of delay is common for live broadcast.

a delay occurs from what is being • Display capacity may not exceed 220 words per minute. If a dialogue

said. • exceeds that rate, selective editing is used to insure that the captions

• remain up-to-date with the current TV screen dialogue.

Captions scrambled with white • Caused by interferences of building, power lines, thunderstorms, etc.

boxes

No captions in a program which

• The broadcast may use a time compression process to speed up the

must contain closed caption

• program. The decoder cannot read the compressed information and

• captions will be lost.

Black box in the TV screen • You are in TEXT mode. Select a CAPTION mode (

“C1”, “C2”) or

• Caption “OFF”.

PROBLEM CORRECTIVE ACTION

Sound OK, Picture Poor

•

Try a new channel, if OK, then possible station trouble.

•

Is antenna connected to jack on the back of the set?

•

If outside antenna is being used, check for broken wire.

•

Check for local interference.

•

Adjust “CONTRAST” & “BRIGHT” control.

Picture OK, Sound Poor

•

Try a new channel, if OK, then possible station trouble.

•

Check for local interference.

No operation by infrared Remote

•

Make sure the AC cord is connected to an AC outlet.

Control

•

Check batteries in remote control.

Different color marks on screen

•

Magnetism from nearby appliances and geomagnetism might affect

the color of the TV picture. Move the unit away from the appliances,

the unit can repair itself automatically. If you want to repair immedi-

ately,

unplug the power cord, then plug it in again 30 minutes later or

so. This automatically resets the unit.

–

•

Some functions are not available in specific modes, but this is not a malfunction. Read the description in

this Owner’s Manual for details on correct operations.

•

Playback from a desired track and random playback are not available during program playback.

PROBLEM CORRECTIVE ACTION

No picture • Insert a correct video disc that plays on this unit.

• Press [SELECT] to select DVD mode, then try other DVD feature.

Disc cannot be played

• Insert the disc.

• Clean the disc.

• Place the disc correctly, with the label side up.

• Cancel the parental lock or change the control level.

No sound

• Connect the audio cables firmly.

• Turn the power of the audio component on.

• Correct the audio output settings.

• Correct the input settings on the audio component.

No DTS audio is output

• This unit does not support DTS audio. This is not a malfunction.

Distorted picture

• There are some cases where pictures may be slightly distorted, which

are not a sign of a malfunction.

• Although pictures may stop for a moment, this is not a malfunction.

Audio or subtitle language • The selected language is not available for audio or subtitles on the

does not match the set up DVD. (This is not a malfunction.)

The camera angle cannot be changed • The DVD does not contain sequences recorded from different camera

angles. (This is not a malfunction.)

Audio or subtitle language cannot be • The DVD does not contain audio source or subtitles in the selected

changed language. (This is not a malfunction.)

“Prohibited icon” appears on the • That operation is prohibited by the unit or the disc.

screen, prohibiting an operation (This is not a malfunction.)

CD sound dropout • Scratched disc. Replace the disc with an unscratched one.

No CD reproduction

DVD picture dropout

DVD picture freeze

DVD picture in mosaic

No DVD reproduction

Disc cannot be inserted • Check if any disc is already in.

Disc cannot be taken out • Unplug and plug again the power cord to the outlet, and then press

[EJECT

• Press and hold

[EJECT

] on the unit for more than 5 seconds.

DVD Mode

NOTE

–

CABINET CLEANING

•

Wipe the front panel and other exterior surfaces of

the unit with a soft cloth immersed in lukewarm

water and wrung dry.

•

Never use a solvent or alcohol. Do not spray insec-

ticide liquid near the unit. Such chemicals may

cause damage and discoloration to the exposed sur-

faces.

SERVICING

•

Should your unit become inoperative, do not try to

correct the problem by yourself. There are no user-

serviceable parts inside. Turn off, unplug the power

cord and please call our help line mentioned on

the front page, to locate an Authorized Service

Center.

IF THE LASER OPTICAL PICKUP UNIT

IS DIRTY

•

If the unit still does not perform properly when it is

operated, while referring to the relevant sections

and to “TROUBLESHOOTING GUIDE” in this

Owner’s Manual, the laser optical pickup unit may

be dirty. Consult your dealer or an Authorized

Service Center for inspection and cleaning of the

laser optical pickup unit.

•

Handle the discs so that fingerprints and dust do

not adhere to the surfaces of the discs.

•

Always store the disc in its protective case when it

is not used.

•

To clean-off, use a soft cloth.

•

Do not use a hard cloth since this will mar the disc.

•

Wipe the disc in a straight line from center to edge.

•

Never wipe with a circular motion.

•

Do not use detergent or abrasive cleaning agents.

DISC HANDLING

MAINTENANCE

–

LCD : 20 inch

Television system : NTSC-M

Closed caption system :§15.119/FCC

Channel coverage:

VHF: 2 ~ 13

UHF: 14 ~ 69

CATV: 2 ~13, A ~ W,

W+1 ~ W+84,

A-5 ~ A-1, 5A

Tuning System: 181 channel

frequency synthesized

tuning system

Channel access: Direct access keyboard,

programmable

scan and up/down

Product type: DVD Player

Discs: DVD video, Audio CD

CD with MP3 files

•

Designs and specifications are subject to change without notice.

•

If there is a discrepancy between languages, the default language will be English.

DVD

GENERAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS

Sound output: 2 speakers, 1W, 8 ohm

OTHER SPECIFICATIONS

Terminals

Antenna input: VHF/UHF/CATV

75 ohm unbalanced (F-type)

S-Video input: Mini DIN 4-pin jack

Video input: RCA connector [ 1

Audio L/R input: RCA connector

[ 4

Component video input:

One pin jack (Y), 1Vpp (75 ohm)

Two pin jacks (Pr)/(Pb), 700mVpp (75 ohm)

Coaxial digital audio output:

One pin jack, 500mmVpp (75 ohm)

Headphone: 1/8" stereo (3.5mm)

Remote control: Digital encoded

infrared light system

Operating

temperature: 5°C to 40°C

(41°F~104°F)

Power requirements: AC 120V, 60Hz

Power consumption

(Maximum): 65W

LCD: 20"

Dimensions: H :20-1/16"(510mm)

W :19-1/2" (495mm)

D :14-7/16"(366mm)

Weight: 15.0 lbs. (6.8kg)

SPECIFICATIONS

- 38 - ES

1.Botón POWER

Presione para encender y apagar la unidad.

2.Botón PICTURE

Presione para ajustar la imagen.

3.Botones numéricos

Presione para seleccionar directamente el número

de canal deseado .

Botón +100 (para modo TV)

Presione para seleccionar canales cuyo número

sea superior a 99.

Botón +10 (para modo DVD)

Presione para introducir los números superiores a

9 deseados.

4.Botón SLEEP

Presione para ajustar el temporizador de reposo

5.Botones SKIP H / G

Presione una vez para omitir capítulos o pistas y

desplazarse a un punto específico.

6.Botón PLAY O

Presione para reproducir el disco.

7.Botón PAUSE F

Presione para hacer una pausa en la reproducción

del disco actual.

8.Botón DISPLAY

Para modo TV

Presione para visualizar el número actual de canal en

la pantalla del televisor.

Para modo DVD

Presione para visualizar el estado actual en la pan-

talla del televisor.

9.Botón SETUP

Presione para entrar o salir del menú de configu-

ración del TV/DVD.

10. Botón TITLE

Presione para visualizar el menú de títulos.

11. Botón CLEAR

Presione para cancelar o borrar un ajuste intro-

ducido actualmente.

Presione para borrar la pantalla “DISCO ADEN-

TRO”.

12. Botón MODE

Presione para visualizar la pantalla de la repro-

ducción programada o la de reproducción aleato-

ria en el modo de parada.

Presione para visualizar la pantalla de ajuste del

nivel del negro o la pantalla de sonido envolvente

durante la reproducción.

13. Botón SEARCH MODE

Presione para localizar un punto deseado.

14. Botón AUDIO

Para modo TV: Presione para seleccionar el

modo de sonido de TV (ESTEREO/SAP/MONO).

Para modo DVD: Presione para seleccionar un

idioma de audio deseado (si está disponible).

15. Botón EJECT A

Presione para extraer un disco de la unidad.

16. Botón SELECT

Presione para seleccionar el modo TV, modo de

entrada externa o modo de DVD.

17. Botones CH.

Presione para seleccionar canales memorizados.

18. Botones VOL.

Presione para controlar el nivel de volumen del

DVD y el televisor.

19. Botón MUTE

Presione para silenciar el sonido. Presiónelo de

nuevo para restablecer el sonido.

20. Botón ZOOM

Presione para ampliar la parte de la imagen repro-

ducida en un DVD.

- MANDO A DISTANCIA

CONTROLES DE OPERACIÓN Y FUNCIONES

■ INDICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 38

PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 39

■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 40

CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 40

CONEXIÓN EXTERNA . . . . . . . . . . . . . . . . . . . . . . . . . 41

SECCIÓN DE TV

■ OPERACIÓN DE TV Y AJUSTES . . . . . . . . . . . . . . . . . 42

PARA MIRAR UN PROGRAMA DE TV . . . . . . . . . . . . 42

AJUSTE DE CANAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

IDIOMA DE MENÚ . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

SECCIÓN DE DVD

■ REPRODUCCIÓN DE UN DISCO . . . . . . . . . . . . . . . . 44

REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 44

MENÚ DE DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

REANUDACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

INDICE

• Para saber cómo funciona el mando a distancia, consulte la [Fig.1] de la página 8.

NOTE

•

Para elegir el modo de DVD presione primero [PLAY

] o [EJECT

], o introduzca un disco en la

ranura. De otra manera, el DVD no funcionará.

PARA INSERTAR LAS PILAS

1 Abra la cubierta del compartimiento de las

pilas empujando la cubierta del mando a dis-

tancia en el sentido de la flecha.

2 Inserte 2 pilas “AA” en el compartimiento de

las pilas, en el sentido indicado por las mar-

cas de polaridad (+/-).

3 Vuelva a poner la cubierta.

PRECAUCIONES A LA HORA DE

INSERTAR LAS PILAS

•

Asegúrese de seguir la polaridad correcta, tal como

se indica en el compartimiento de las pilas. Si se

colocan las pilas con la polaridad invertida se

pueden ocasionar daños a la unidad.

•

No mezcle distintos tipos de pilas (ej. alcalina y de

carbón-zinc) o pilas viejas con nuevas.

•

Si no va a usarse la unidad durante un período

largo de tiempo, quite las pilas para prevenir daños

o lesiones ocasionadas por posibles fugas de las

pilas.

•

No intente recargar las pilas que no sean para

recargar; pueden sobrecalentarse y estropearse.

- 39 - ES

NOTA

21. Botón REV

Presione para ver la imagen en DVD en retroceso

o en cámara lenta de retroceso.

Botón FWD

Presione para mover en avance rápido o en

cámara lenta en el disco.

22. Botón STOP C

Presione para detener la reproducción del disco.

23. Botón DISC MENU

– Muestra el menú del DVD.

– Muestra la lista de archivos del disco MP3.

24. Botón ENTER

Presione para establecer un ajuste.

25. Botones

(Arriba) /

(Abajo) /

{

(Izquierda) /

(Derecha)

Presione para seleccionar o ajustar los ítems del

menú.

26. Botón RETURN

Presione para volver a la pantalla anterior en el

menú de configuración.

27. Botón A-B

Presione para repetir la reproducción de una sec-

ción seleccionada.

28. Botón ANGLE

Presione para cambiar el ángulo de la cámara y

ver la secuencia que se está reproduciendo desde

un ángulo diferente (si existe).

29. Botón REPEAT

Repite la reproducción del disco, título, capítulo,

grupo o pista actual.

30. Botón SUBTITLE

Presione para seleccionar el idioma de los subtí-

tulos.

•

No se recomienda el uso de mandos a distancia universales. No todas las funciones pueden controlarse

con un mando a distancia universal.

Si decide usar un mando a distancia universal con esta unidad, sea consciente de que el número de código

suministrado puede no adecuarse a la unidad. En este caso, llame al fabricante del mando a distancia uni-

versal.

31. Botón STOP P

Presione para detener la reproducción del disco.

32. Botón MENU

Presione para entrar o salir del menú de configu-

ración del TV/DVD.

33. Botones VOLUME

Presione para controlar el nivel de volumen del

DVD y el televisor.

34. Botones CHANNEL

Presione para seleccionar canales memorizados.

35. Botón SELECT

Presione para seleccionar el modo TV, modo de

entrada externa o modo de DVD.

36. Botón POWER

Presione para encender y apagar la unidad.

37. Botón EJECT

Presione para extraer un disco de la unidad.

38. Ventana de sensor remoto

39. Botón PLAY O

Presione para reproducir el disco.

- PANEL FRONTAL

• Para ver la ilustración del panel frontal, vaya a la página 9, [Fig. 2].

- 40 - ES

SI TIENE UNA TOMA DE PARED

Conecte el televisor a la toma de antena de pared con

el cable RF (disponible en los comercios).

SI TIENE CABLE DE HILOS

Conecte el televisor al cable de antena.

•

Antes de conectar la antena en la toma ANT. de la unidad,

compruebe que la patilla no esté torcida. Si lo está, ponga la

patilla recta tal como se muestra en la ilustración y a contin-

uación conecte la patilla a la toma ANT. de la unidad.

•

Los cables utilizados aquí están disponibles en los comercios.

•

Para su seguridad y para evitar daños a la unidad, desconecte el cable de antena de la toma ANT.

antes de trasladar la unidad.

NOTA

PREPARACIÓN PARA LA UTILIZACIÓN

CONEXIONES DE ANTENA/CABLE

- CONEXIONES DE ANTENA/CABLE

(

)

CPM

ENT

Cable RF

[Parte posterior de

este unidad]

desde Compañia de Cable o

Antena de Satélite

ANT

(

)

ANT

SALIDA ENTRADA

Cable coaxial

de 75 ohmios

desde Compañia de Cable o

Antena de Satélite

Caja de convertidor

o caja de satélite

[Parte posterior de este unidad]

Para el instalador de sistemas CATV:

•

Esta nota tiene la finalidad de llamar la atención del instalador de sistemas CATV para que tenga en cuenta el

Artículo 820-40 de la NEC, que proporciona recomendaciones para hacer una conexión a tierra apropiada y, en par-

ticular, especifica que la tierra del cable debe conectarse al sistema de puesta a tierra del edificio, tan cerca del punto

de entrada del cable como sea posible.

NOTA

Patilla torcida

Cable

Conector

(Debe ponerse

recta)

(patilla recta)

NOTA

CUANDO SE USA UNA CAJA DE CON-

VERTIDOR/CAJA DE SATÉLITE

Si su compañía de televisión por cable le suministra

una caja de convertidor o si usa un sistema de

satélite, podrá utilizar la conexión básica que se

muestra anteriormente.

La selección de los canales deberá hacerse con la

caja de convertidor o caja de satélite. Esto significa

que no es posible cambiar de canal utilizando el

mando a distancia de la unidad.

- CONEXIÓN CON CAJA DE CONVERTIDOR /CAJA DE SATÉLITE

- SALIDA DE AUDIO

DIGITAL

AUDIO OUT

(COAXIAL)

Descodificador Dolby Digital

A toma de ENTRADA

DIGITAL COAXIAL DE AUDIO

Equipo doméstico de audio

Podrá disfrutar de un sonido de DVD con

más presencia desconectando el equipo de

audio digital, tal como el descodificador

Dolby Digital.

- ENTRADA DE VÍDEO2

COMPONENT

VIDEO2

AUDIO

Cable de audio

Videojuego

ej.

(SALIDA)

Cable de vídeo

componente

Use esta conexión si el equipo A/V (ej. videocámara

o videojuego) tiene tomas de salida de vídeo COM-

PONENTE (Y,Pb,Pr). Podrá disfrutar de una mejor

imagen con esta conexión.

- 41 - ES

•

La fuente de audio de un disco en un formato de sonido envolvente Dolby Digital de 5,1 canales no se

puede grabar como sonido digital mediante una pletina MD o DAT.

•

Si conecta un descodificador Dolby Digital, ajuste la función “DOLBY DIGITAL” a “BITSTREAM”

para salida de audio en el modo de configuración. (Consulte la página 30).

•

A menos que se haga la conexión a un decodificador “DOLBY DIGITAL” a “PCM” para salida de audio

en el modo de configuración.

La reproducción en una unidad utilizando ajustes incorrectos puede generar ruido y distorsión, y también

puede provocar daños a los altavoces. (Consulte la página 30).

NOTA

•

Si su propio equipo es monofónico (sólo tiene una toma de audio), conecte el cable de audio a la toma AUDIO L de esta unidad.

•

Si conecta la toma VIDEO y la toma S-VIDEO simultáneamente, se da prioridad a la S-VIDEO. .

Puede conectar esta unidad a su equipo de audio/vídeo.

•

Asegúrese de apagar todos los componentes del

sistema antes de conectar otro componente.

•

Consulte los manuales de instrucciones de los

componentes que va a conectar a la unidad.

- ENTRADA DE VÍDEO1

CONEXIÓN EXTERNA

DIG

ITA

)

IDEO

VIDEO2

UDIO

AUDIO

IDEO1

ANT

AD P

AUDIO

VIDEO2

VIDEO1

[Parte posterior

de este unidad]

Cable de audio

Videograbadora

ej.

(SALIDA)

Cable VIDEO-S

Cable de vídeo

S-VIDEO

VID

VIDEO1

AUDIO

NOTA

Use esta conexión si su propio equipo A/V (ej.

videograbadora) tiene tomas de salida de audio y

vídeo. Cuando se usa un cable Vídeo-S, se obtiene

una imagen mejor.

Fabricado bajo licencia de Dolby Laboratories. “Dolby” y el símbolo de la doble D son marcas comerciales de

Dolby Laboratories.

Cuando utilice las tomas de entrada externa selec-

cione el “AUX1” o “AUX2” presionando [INPUT

SELECT]. (Consulte la página 42.)

•

Para utilizar la tomas VIDEO1, seleccione

“AUX1”.

•

Para utilizar la tomas VIDEO1, seleccione

“AUX2”.

NOTA

- 42 - ES

•

Los botones sombreados se utilizan para las siguientes operaciones.

1 Conecte el cable de alimentación de

la unidad a una toma estándar CA.

•

Si se visualiza algún dígito en la esquina de la

pantalla, presione [POWER] sin desconectar

el cable de alimentación.

2 Presione [POWER] para encender la unidad.

3 Presione [CH.

] para seleccionar el

número de canal deseado.

Presione los botones numéricos para intro-

ducir el número de canal deseado.

Para seleccionar el número de canal medi-

ante los botones numéricos:

•

Para seleccionar un número de canal de un

solo dígito, presione primero [0] (ej. Para el

canal 2, presione [0] [2]).

•

Para seleccionar canales por cable cuyos números

sean superiores a 99, presione primero[+100/+10].

(ej. Para el canal 125, presione [+100/+10] [2] [5]).

4 Presione [VOL.

] para seleccionar el

nivel de volumen deseado.

•

Presione [MUTE] para silenciar el sonido al instante.

Vuelva a presionarlo para restaurar el nivel de

volumen anterior.

•

Si presiona [CH.

] en el modo DVD,

puede cambiar los canales del televisor. Incluso

si apaga la unidad en el modo DVD, cuando

vuelve a encenderlo se pondrá en el modo TV.

PARA VER UN CANAL POR CABLE O

SATÉLITE

Si la unidad está conectada a una caja de convertidor

o caja de satélite, presione [CH.

] para selec-

cionar CH3 o CH4 según el ajuste de canal de salida

del aparato, y seleccione en él el canal deseado.

PARA VER SEÑALES DE ENTRADA DE

UN DISPOSITIVO EXTERNO

Cuando conecte un equipo externo a las tomas de

entrada delanteras AUDIO/VIDEO, presione

[SELECT] o [CH.

] repetidamente hasta que

aparezca en la pantalla “AUX1” o “AUX2”.

•

Si hay un disco dentro de la unidad, se visu-

alizará el mensaje “DISCO ADENTRO” en la

pantalla durante 10 segundos.

•

Para borrar el mensaje al instante, presione [CLEAR].

OPERACIÓN DE TV Y AJUSTES

PARA MIRAR UN PROGRAMA DE TV

VOLUMEN 20

C C C C C C C C C C C C C C C C

SECCIÓN DE TV

REV

SLOW

PLAY

STOP

FWD

ENTER

PAUSE

DISC

RETURNTITLESETUP

REPEATSEARCH MODE

CLEAR

DISPLAY

SKIP

SELECT

POWER

PICTURE EJECT

CH.

VOL.

MUTEZOOM

SLEEP

123

456

789

0 +10

+100

CH.

POWER

123

456

789

0 +10

+100

VOL.

NOTA

DISCO ADENTRO

- 43 - ES

PROGRAMACIÓN AUTOMÁTICA DE CANAL

De acuerdo con la configuración de fábrica, esta

unidad ha memorizado todos los canales, incluidos

los que no están disponibles en su localidad. Esta

función solo pone automáticamente en memoria los

canales disponibles.

1 Presione [SETUP] y a continuación presione

[

] o [

] para señalar “AJUSTE DE CANAL”.

2 Presione [ENTER] y a continuación presione

[

] o [

] para señalar “PREA. AUTO CA.”.

3 Presione [ENTER].

•

El sintonizador explora y memoriza todos los

canales activos de su localidad.

•

El sintonizador se detiene en el canal memorizado

inferior.

•

Cuando está activado “PREA. AUTO CA.”

donde no hay entrada de señal de TV, apare-

cerá “NO HAY SEÑAL DE TV” en la pan-

talla después de completarse la exploración

de los canales

•

La unidad puede reconocer canales CATV como

canales de TV si las condiciones de recepción

son malas. En este caso, compruebe la conexión

de la antena y vuelva a intentar “PREA. AUTO

CA.” cuando las condiciones de recepción

mejoren.

•

La programación de canales memorizados

NO es necesaria cuando la unidad está conec-

tada a una caja de convertidor o caja de

satélite. Sólo tiene que seleccionar el canal

para caja de convertidor o entrada de satélite

(ej. CH3) de la unidad y a continuación selec-

cione el canal que desee en la caja de conver-

tidor o la caja de satélite.

1 Presione [SETUP] y a continuación presione

[K] o [L] para seleccionar el “LANGUAGE”.

2 Presione [ENTER] repetidamente para selec-

cionar “ENGLISH” = inglés, “ESPAÑOL” o

“FRANÇAIS”= francés.

3 Presione [SETUP] para salir del menú.

•

Esta función selecciona sólo el idioma del

menú de pantalla; no la fuente de audio.

•

Si por alguna razón el menú está en español o

en francés, presione [SETUP], luego [K] o

[L] para seleccionar “IDIOMA [ESPAÑOL]”

o “LANGAGE [FRANÇAIS]”, y a contin-

uación presione [ENTER] repetidamente para

seleccionar el idioma deseado y luego pre-

sione [SETUP].

SETUP

- TV PREP. -

B AJUSTE DE CANAL

AJUSTE DE V-CHIP

IDIOMA [ESPAÑOL]

TITULO [OFF]

LUZ DE FONDO

[BRILLO]

ENTER

– AJUSTE DE CANAL –

AGREGAR/BORRAR CA (CATV)

B PREA. AUTO CA.

ENTER

AJUSTE DE CANAL

NOTA

- TV SET UP -

CHANNEL SET UP

V-CHIP SET UP

B LANGUAGE [ENGLISH]

CAPTION [OFF]

BACK LIGHT [BRIGHT]

SETUP

ENTER

IDIOMA DE MENÚ

NOTA

- 44 - ES

•

Los botones sombreados se utilizan para las sigu-

ientes operaciones.

PARA EMPEZAR

Si es necesario, encienda el amplificador y cualquier

otro componente.

1 Presione [POWER] para encender la unidad.

2 Abra la bandeja del disco manualmente.

Introduzca el disco elegido con la etiqueta hacia la parte trasera de la

unidad para reproducirlo. Al presionar suavemente el disco para intro-

ducirlo en la ranura, su reproducción empezará automáticamente.

•

La reproducción empezará desde el primer capí-

tulo/pista del disco.

•

Si la reproducción no empieza automáticamente,

presione [PLAY O].

Presione [STOP C] para detener la reproducción.

5 Precione [EJECT

] para extraer la disco de

la unidad.

•

Cuando el modo DVD se ha cambiado al modo

TV, el modo DVD se desactiva primero y a

continuación aparece la imagen y suena el

sonido en el TV al cabo de unos 4 segundos.

De la misma manera, cuando se presiona

[POWER] para apagar la unidad en el modo

DVD, este modo se desactiva primero y a con-

tinuación se apaga la unidad.

•

Puede aparecer “ ” en la parte superior

derecha de la pantalla del TV durante su fun-

cionamiento, que avisa de que el DVD o el

disco han encontrado una operación prohibida.

•

Con los DVD que utilizan títulos para señales

de reproducción programada, la reproducción

puede empezar desde el segundo título y

puede omitir estos títulos.

•

Durante la reproducción de un disco de dos

capas, las imágenes pueden detenerse durante

un rato. Esto ocurre cuando la 1ª capa cambia

a la 2ª. No se trata de una anomalía.

REPRODUCCIÓN DE MP3

En el modo de parada, presione [DISC MENU] y precione

[

] o [

] para seleccionar el grupo o pista que desee.

•

Si ha selecciona un grupo, presione [B] o

[ENTER] para ir a la pantalla de selección de

pistas. Presione [s] para volver a la pantalla

anterior (excepto la página superior).

•

Si ha seleccionado una pista, presione [ENTER]

para empezar a reproducir pistas. Si empieza por

la que acaba de elegir se reproducirán las pistas

siguientes.

•

Si no puede visualizarse enseguida en pantalla la

lista entera de archivos, aparece la “

”para ir a la

página siguiente. appears to go to the next page.

•

Presione [TITLE] para volver al archivo superior

de la jerarquía más alta del programa y de la

lista de archivos.

Presione [STOP

] para detener la reproducción.

REPRODUCCIÓN DE UN DISCO

REPRODUCCIÓN BÁSICA

REV

SLOW

PLAY

STOP

FWD

ENTER

PAUSE

DISC

RETURNTITLESETUP

DISPLAY

SKIP

VOL.

MUTEZOOM

SLEEP

0 +10

+100

SELECT

POWER

PICTURE EJECT

123

POWER

NOTA

Nombre de carpeta 1

LISTA DE ARCHIVOS

Nombre de carpeta 2

Nombre de carpeta 3

Nombre de carpeta 4

Nombre de archivo 1

Nombre de archivo 2

Nombre de archivo 3

Nombre de carpeta 1

NOMBRE DE DISCO

DISC

STOP

SECCIÓN DE DVD

EJECT

STOP

- 45 - ES

1 Presione [DISC MENU].

•

Aparecerá el menú principal de DVD

•

Si esta función no está disponible, el símbo-

lo puede aparecer en la pantalla del televisor.

•

Si el menú de disco está disponible en el disco,

aparecerán las opciones de idioma de audio, de

subtítulos, capítulos del título y otras para su

selección.

2 Presione [K], [L], [s] o [B] para seleccionar

un ítem y presione [ENTER] para confirmar la

selección.

1 Durante la reproducción, presione [STOP C].

(Ejemplo: DVD o CD audio)

•

Aparecerá el mensaje de reanudación en la pan-

talla del TV.

2 Presione [PLAY O], la reproducción contin-

uará desde el punto donde se paró la repro-

ducción.

•

Para cancelar el modo de reanudación, presione

dos veces [STOP C].

•

Para MP3, la reproducción se reanudará desde el

principio de la pista actual.

•

La información de reanudación permanece acti-

vada incluso cuando apaga el interruptor princi-

pal.

REANUDACIÓN

MENÚ DE DISCO

DISC

ENTER

STOP

PLAY

Presione 'PLAY' para reproducir

desde aquí.

Para reproducir desde el inicio,

primero presione 'STOP' y luego 'PLAY'.

REANUDACIÓN ACTIVADA

•

Las carpetas se conocen como grupos; los

archivos, como pistas.

•

Los archivos MP3 van acompañados de iconos.

•

Se puede reconocer un máximo de 255 carpetas.

•

Se puede reconocer un máximo de 999 archivos.

•

Pueden crearse hasta 8 jerarquías.

Se recomienda para esta unidad el uso de archivos

grabados según las especificaciones siguientes:

•

Frecuencia de muestreo: 44,1 kHz o 48kHz

•

Velocidad de transmisión de bits constante:

32kbps ~ 320kbps

•

Para archivos MP3 grabados en velocidad de

transmisión de bits variable (VBR), la unidad

puede no mostrar el tiempo real transcurrido.

NOTA

- 46 - ES

MEMO

- 47 - ES

MEMO

Printed in China 1EMN20477

L3250UA ★★★★★

LIMITED WARRANTY

FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or

workmanship as follows:

DURATION:

PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the

date of original retail purchase. Two (2) years for Picture Tube. Certain parts and LCD image burn-in

are not covered under this warranty.

LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of

original retail purchase.

LIMITS AND EXCLUSIONS:

THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE

RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH

THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing

or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to

any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It

does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not

supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,

alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this

product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE

CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY

GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE

USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF

FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS

REPRESENTATIVES IN THE UNITED STATES.

ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED

SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO A FUNAI

AUTHORIZED SERVICE FACILITY.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS

THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE

UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI

CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT

WITHOUT PRIOR NOTICE.

To locate your nearest Authorized Service Center or for general service inquiries, please call or

write to the following:

FUNAI CORPORATION, INC.

SERVICE CENTER

19900 Van Ness Avenue, Torrance, CA 90501

Tel :1-800-968-3429

http://www.SylvaniaConsumerElectronics.com

Head Office: 100 North Street, Teterboro, NJ 07608

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

Sylvania 6620 LDF Manual de usuario

Marca: Sylvania

Modelo: 6620 LDF

Categoría: Reproductores de DVD

Tipo: Manual de usuario

Este manual también es adecuado para

Descargar PDF

informe

En otros idiomas

English: Sylvania 6620 LDF User manual

Sylvania 6620 LDF Manual de usuario

Este manual también es adecuado para

Sylvania 6620 LDF Manual de usuario

En otros idiomas

Documentos relacionados

Otros documentos