Whirlpool AKR 931 AL-1 Program Chart

Categoría
Campanas de cocina
Tipo
Program Chart
AKR 931
5019 100 75182/A
INSTALLATIONSANGABEN
Mindestabstand zur Kochfläche: 65 cm (Elektroplatten), 75 cm (Gas-, Öl-,
Kohlekochmulde). Folgen Sie bei der Installation der Nummerierung (1
Ö
2
Ö
3
Ö
.....). Das
Auslassrohr und die Befestigungsmanschetten (18) werden nicht mitgeliefert und
müssen gesondert erworben werden. Das Gerät darf erst nach erfolgter Installation an die
Stromversorgung angeschlossen werden. Der Stecker der Dunstabzugshaube muss mit
einer normgerechten und gut zugänglichen Steckdose verbunden werden. Wenn die
Dunstabzugshaube nicht mit einem Stecker versehen ist (direkter Netzanschluss), muss
ein zweipoliger, normgerechter, gut zugänglicher Schalter eingebaut werden, dessen
Kontakte einen Abstand von mindestens 3 mm aufweisen). Prüfen Sie den
Stromanschluss der Beleuchtung und des Motors (17).
INSTALLATION SHEET
Minimum height above cooker: 65 cm (electric cookers), 75 cm (gas, gas oil or coal
cookers). To install follow points (1
Ö
2
Ö
3
Ö
.....). The exhaust pipe and fixing tabs (18) are
not provided and should be bought separately. Do not connect the appliance to the
electrical power supply until installation is completed. The power plug of the hood must
be connected to a socket that complies with current regulations, located in an easily
accessible point. If the hood is not fitted with a plug (direct connection to the power
supply), fit a two-pole switch in compliance with regulations, with minimum break
distance between contacts of 3 mm (easily accessible). Check that electrical connections
of lights and motor (17) are correct.
FICHE D'INSTALLATION
Distance minimale par rapport à la cuisinière : 65 cm (cuisinière électrique), 75 cm
(cuisinière à gaz, mazout ou charbon). Pour le montage, suivez la numérotation
(1
Ö
2
Ö
3
Ö
.....). Le tuyau d'évacuation et les colliers de fixation (18) ne sont pas fournis
avec l'appareil et doivent être achetés à part. Ne branchez pas l'appareil tant que
l'installation n'est pas terminée. La fiche de la hotte doit être branchée dans une prise
conforme aux normes en vigueur, placée dans un endroit accessible. Si la hotte est
dépourvue de fiches (branchement direct sur le réseau), appliquez un interrupteur
bipolaire conforme aux normes ayant une ouverture minimale de 3 mm entre les contacts
(accessible). Contrôlez que le branchement électrique de l'éclairage et du moteur (17) ont
été effectués correctement.
INSTALLATIEKAART
Minimumafstand tot het kooktoestel: 65 cm (elektrische kooktoestellen), 75 cm
(kooktoestellen op gas, olie of kolen). Voor de montage volg de nummering (1
Ö
2
Ö
3
Ö
.....).
De afvoerleiding en de bevestigingsbandjes (18) worden niet bijgeleverd en dienen
aangeschaft te worden. Geef het apparaat geen stroom totdat de installatie geheel
voltooid is. De stekker van de kap moet op een goed toegankelijk stopcontact
aangesloten worden dat aan de geldende veiligheidsvoorschriften voldoet. In het geval
dat de kap geen stekker heeft (directe aansluiting op het elektriciteitsnet) dient u een
tweepolige schakelaar te gebruiken met een afstand tussen de contacten van minstens
3 mm, die aan de geldende voorschriften voldoet). Verzeker u ervan dat de verlichting en
de motor correct aangesloten zijn (17).
D
GB
F
NL
75182a.fm5 Page 1 Wednesday, November 22, 2000 12:23 PM
5019 100 75182/A
AKR 931
FICHA DE INSTALACIÓN
Distancia mínima de los quemadores: 65 cm (quemadores eléctricos), 75 cm
(quemadores de gas, gasóleo o carbón). Para el montaje, siga la numeración
(1
Ö
2
Ö
3
Ö
.....). El tubo de descarga y las abrazaderas de fijación (18) no se vienen con la
campana y se deben comprar aparte. No se debe enchufar el aparato hasta que su
instalación no esté terminada. Si el aparato está provisto de clavija, enchúfelo en una
toma de corriente conforme a las normas vigentes que esté colocada en una zona
accesible. Si el aparato viene sin clavija porque se debe conectar directamente a la red
hay que instalar en un punto accesible un interruptor bipolar conforme a las normas
vigentes en el que la distancia entre contactos abiertos no sea inferior a 3 mm.
Compruebe si las luces y el motor están bien conectados (17).
FICHA DE INSTALAÇÃO
Distância mínima dos fogões: 65 cm (fogões eléctricos), 75 cm (fogões a gás, óleo ou
carbono). Para a montagem siga a numeração (1
Ö
2
Ö
3
Ö
.....). O tubo de descarga e as
tiras de fixação (18) não são fornecidos com o aparelho pelo que devem ser adquiridos.
Não ligue o aparelho à corrente eléctrica até a instalação estar concluída. A ficha eléctrica
do exaustor deve estar ligada a uma tomada em conformidade com as normas em vigor,
e colocada num sítio acessível. Se o exaustor não estiver equipado com uma ficha
(ligação directa com a rede eléctrica) aplique um interruptor bipolar segundo as normas
com uma distância dos contactos à abertura não inferior a 3 mm (acessível). Controle se
a ligação eléctrica das luzes e do motor está feita correctamente (17).
SCHEDA INSTALLAZIONE
Distanza minima dai fuochi: 65 cm (fuochi elettrici), 75 cm (fuochi a gas, gasolio o
carbone). Per il montaggio seguire la numerazione (1
Ö
2
Ö
3
Ö
.....). Il tubo di scarico e le
fascette di fissaggio (18) non sono fornite e vanno acquistate. Non dare corrente
all’apparecchio finché l’installazione non è totalmente completata. La spina elettrica della
cappa deve essere allacciata ad una presa conforme alle norme vigenti posta in zona
accessibile. Se la cappa è sprovvista di spina (collegamento diretto alla rete) applicare un
interruttore bipolare a norme con una distanza dei contatti in apertura non inferiore a
3 mm (accessibile). Controllare il corretto collegamento elettrico di luci e motore (17).
ùüùü+ùùùþ
ü$12.)12.1.)2"0120" FP02 !"0120" FP0120".0! #
02!0. #0! # +.22  21.  #1202.!1
1
Ö
2
Ö
3
Ö
.....
1&.". .&".2. !.120!&1"/0/.202.0
2. !! 32!..!0.. 2 *$&!122! 3 / 2020002!)
!0*.21#10#!2!&12"0.212.1"02!)3"2 #
. !! 32!.!0.1#/0010!.102 #1$* 2 ". 1 *
2  0210! 101 10ü . !! 32!."/0/.203"
.0#0."1*/0102 /2# 2  02120./ )/.)2102&
. 1+00$12  .02.*2&0.3+ PP 10! 101 10
ü2021&1202!1*/013&212+.2!
E
P
I
GR
75182a.fm5 Page 2 Wednesday, November 22, 2000 12:23 PM
AKR 931
5019 100 75182/A
Nur in der Umluftversion
For Filter Version only
Uniquement pour la Version
filtrante
Uitsluitend voor de filterversie
Sólo para el modelo filtrador
Apenas para Versão filtrante
Solo per Versione filtrante
) . 2  . .!!)31"
75182a.fm5 Page 3 Wednesday, November 22, 2000 12:23 PM
5019 100 75182/A
AKR 931 PRODUCT SHEET
1.
Control panel
a.
Light ON/OFF switch.
b.
Extraction and minimum extraction speed
selection ON/OFF switch.
c.
Medium extraction speed selection
switch.
d.
Maximum extraction speed selection
switch.
2.
Grease filters
3.
Halogen bulbs
4.
Flues
5.
Air vent (for Filter Version)
Cleaning the grease filter
Wash the grease filter at least once a month.
1.
Unplug the appliance or disconnect the mains
power supply.
2.
Remove the grease filters -
Fig. 1
: pull the
spring release handle downwards, then
remove the filter.
3.
After cleaning the grease filter refit in reverse
order, making sure the entire extraction
surface is covered.
Carbon filter Fitting and Maintenance
Fitting the carbon filter:
1.
Unplug the appliance or disconnect the mains
power supply.
2.
Remove the grease filter
(f - Fig. 1)
.
3.
Remove the screw and then the filter holder
(g - Fig. 2)
.
4.
Fit the carbon filter
(i - Fig. 2)
in the filter
holder
(h - Fig. 2)
5.
Refit the filter holder
(j - Fig. 2)
and secure it
to the hood with the screw
(g - Fig. 2)
.
6.
Refit the grease filter.
Carbon filter maintenance:
Unlike traditional carbon filters, this carbon filter
can be washed and reactivated.
With normal hood use, the filter should be
cleaned once a month. The filter is best washed
in a dishwasher at the highest temperature
possible, using a normal dishwasher detergent.
To avoid particles of food or dirt settling on the
filter during washing and giving rise to unpleasant
smells, it is advisable to wash the filter on its own.
After washing, dry the filter in the oven at 100° C
for 10 minutes to reactivate it.
The filter will retain its odour-absorbing capacity
for three years, after which it will have to be
replaced.
Replacing bulbs - Fig. 3
1.
Unplug the appliance or disconnect the mains
power supply.
2.
Using a screwdriver or any other suitable tool,
prise off the lamp cover.
3.
Remove the burnt-out bulb.
4.
Replace using 20W max halogen bulbs only,
making sure not to touch them with your
hands.
5.
Replace the lamp cover so that it clicks into
position.
g
j
h
i
f
f
Fig. 1
Fig. 2
Fig. 3
F NL E PGBD GRI
75182a.fm5 Page 6 Wednesday, November 22, 2000 12:23 PM

Transcripción de documentos

75182a.fm5 Page 1 Wednesday, November 22, 2000 12:23 PM AKR 931 D INSTALLATIONSANGABEN Mindestabstand zur Kochfläche: 65 cm (Elektroplatten), 75 cm (Gas-, Öl-, Kohlekochmulde). Folgen Sie bei der Installation der Nummerierung (1Ö2Ö3Ö.....). Das Auslassrohr und die Befestigungsmanschetten (18) werden nicht mitgeliefert und müssen gesondert erworben werden. Das Gerät darf erst nach erfolgter Installation an die Stromversorgung angeschlossen werden. Der Stecker der Dunstabzugshaube muss mit einer normgerechten und gut zugänglichen Steckdose verbunden werden. Wenn die Dunstabzugshaube nicht mit einem Stecker versehen ist (direkter Netzanschluss), muss ein zweipoliger, normgerechter, gut zugänglicher Schalter eingebaut werden, dessen Kontakte einen Abstand von mindestens 3 mm aufweisen). Prüfen Sie den Stromanschluss der Beleuchtung und des Motors (17). GB INSTALLATION SHEET Minimum height above cooker: 65 cm (electric cookers), 75 cm (gas, gas oil or coal cookers). To install follow points (1Ö2Ö3Ö.....). The exhaust pipe and fixing tabs (18) are not provided and should be bought separately. Do not connect the appliance to the electrical power supply until installation is completed. The power plug of the hood must be connected to a socket that complies with current regulations, located in an easily accessible point. If the hood is not fitted with a plug (direct connection to the power supply), fit a two-pole switch in compliance with regulations, with minimum break distance between contacts of 3 mm (easily accessible). Check that electrical connections of lights and motor (17) are correct. F FICHE D'INSTALLATION Distance minimale par rapport à la cuisinière : 65 cm (cuisinière électrique), 75 cm (cuisinière à gaz, mazout ou charbon). Pour le montage, suivez la numérotation (1Ö2Ö3Ö.....). Le tuyau d'évacuation et les colliers de fixation (18) ne sont pas fournis avec l'appareil et doivent être achetés à part. Ne branchez pas l'appareil tant que l'installation n'est pas terminée. La fiche de la hotte doit être branchée dans une prise conforme aux normes en vigueur, placée dans un endroit accessible. Si la hotte est dépourvue de fiches (branchement direct sur le réseau), appliquez un interrupteur bipolaire conforme aux normes ayant une ouverture minimale de 3 mm entre les contacts (accessible). Contrôlez que le branchement électrique de l'éclairage et du moteur (17) ont été effectués correctement. NL INSTALLATIEKAART  Minimumafstand tot het kooktoestel: 65 cm (elektrische kooktoestellen), 75 cm (kooktoestellen op gas, olie of kolen). Voor de montage volg de nummering (1Ö2Ö3Ö.....). De afvoerleiding en de bevestigingsbandjes (18) worden niet bijgeleverd en dienen aangeschaft te worden. Geef het apparaat geen stroom totdat de installatie geheel voltooid is. De stekker van de kap moet op een goed toegankelijk stopcontact aangesloten worden dat aan de geldende veiligheidsvoorschriften voldoet. In het geval dat de kap geen stekker heeft (directe aansluiting op het elektriciteitsnet) dient u een tweepolige schakelaar te gebruiken met een afstand tussen de contacten van minstens 3 mm, die aan de geldende voorschriften voldoet). Verzeker u ervan dat de verlichting en de motor correct aangesloten zijn (17). 5019 100 75182/A 75182a.fm5 Page 2 Wednesday, November 22, 2000 12:23 PM AKR 931 E FICHA DE INSTALACIÓN Distancia mínima de los quemadores: 65 cm (quemadores eléctricos), 75 cm (quemadores de gas, gasóleo o carbón). Para el montaje, siga la numeración (1Ö2Ö3Ö.....). El tubo de descarga y las abrazaderas de fijación (18) no se vienen con la campana y se deben comprar aparte. No se debe enchufar el aparato hasta que su instalación no esté terminada. Si el aparato está provisto de clavija, enchúfelo en una toma de corriente conforme a las normas vigentes que esté colocada en una zona accesible. Si el aparato viene sin clavija porque se debe conectar directamente a la red hay que instalar en un punto accesible un interruptor bipolar conforme a las normas vigentes en el que la distancia entre contactos abiertos no sea inferior a 3 mm. Compruebe si las luces y el motor están bien conectados (17). P FICHA DE INSTALAÇÃO Distância mínima dos fogões: 65 cm (fogões eléctricos), 75 cm (fogões a gás, óleo ou carbono). Para a montagem siga a numeração (1Ö2Ö3Ö.....). O tubo de descarga e as tiras de fixação (18) não são fornecidos com o aparelho pelo que devem ser adquiridos. Não ligue o aparelho à corrente eléctrica até a instalação estar concluída. A ficha eléctrica do exaustor deve estar ligada a uma tomada em conformidade com as normas em vigor, e colocada num sítio acessível. Se o exaustor não estiver equipado com uma ficha (ligação directa com a rede eléctrica) aplique um interruptor bipolar segundo as normas com uma distância dos contactos à abertura não inferior a 3 mm (acessível). Controle se a ligação eléctrica das luzes e do motor está feita correctamente (17). I SCHEDA INSTALLAZIONE Distanza minima dai fuochi: 65 cm (fuochi elettrici), 75 cm (fuochi a gas, gasolio o carbone). Per il montaggio seguire la numerazione (1Ö2Ö3Ö.....). Il tubo di scarico e le fascette di fissaggio (18) non sono fornite e vanno acquistate. Non dare corrente all’apparecchio finché l’installazione non è totalmente completata. La spina elettrica della cappa deve essere allacciata ad una presa conforme alle norme vigenti posta in zona accessibile. Se la cappa è sprovvista di spina (collegamento diretto alla rete) applicare un interruttore bipolare a norme con una distanza dei contatti in apertura non inferiore a 3 mm (accessibile). Controllare il corretto collegamento elettrico di luci e motore (17). GR ù üùü+ ù ù ùþ 5019 100 75182/A  ü$12.Œ)12.1.Œ)2"0120" FP 02!"0120"  FP 0120".0! # Œ02!0. #0! # +.22 Œ 21.  #1202.!1 1Ö2Ö3Ö..... 1&.".Œ.&".2. !.120!&1"  /0/.202.0 2 .Œ !! 32!..Œ!Œ0..Œ 2 *$&!122! 3 / 2020002!) !0*.21#10#Œ!2  !&12"0.212.1" 02!)3"2 # .Œ !! 32!.Œ!Œ0.1#/0010Œ!.102 #1$* 2 ". 1 * 2 Œ 0210Œ! 1Œ01 10 ü .Œ !! 32!."/0/.203" .Œ0#0."1*/0102 /2# 2 Œ 02120./Œ )/.)Œ2102& . 1+00$12  .02.*2&0Œ.3+ PP 10Œ! 1Œ01 10  ü2021&1202!1*/013&212+. 2!   75182a.fm5 Page 3 Wednesday, November 22, 2000 12:23 PM AKR 931  Nur in der Umluftversion For Filter Version only Uniquement pour la Version filtrante Uitsluitend voor de filterversie Sólo para el modelo filtrador Apenas para Versão filtrante Solo per Versione filtrante ) . 2 ..!!)31" 5019 100 75182/A 75182a.fm5 Page 6 Wednesday, November 22, 2000 12:23 PM AKR 931 PRODUCT SHEET 1. Control panel a. Light ON/OFF switch. b. Extraction and minimum extraction speed selection ON/OFF switch. c. Medium extraction speed selection switch. d. Maximum extraction speed selection switch. 2. Grease filters 3. Halogen bulbs 4. Flues 5. Air vent (for Filter Version) Cleaning the grease filter Wash the grease filter at least once a month. 1. Unplug the appliance or disconnect the mains power supply. 2. Remove the grease filters - Fig. 1: pull the spring release handle downwards, then remove the filter. 3. After cleaning the grease filter refit in reverse order, making sure the entire extraction surface is covered. Carbon filter Fitting and Maintenance Fitting the carbon filter: 1. Unplug the appliance or disconnect the mains power supply. 2. Remove the grease filter (f - Fig. 1). 3. Remove the screw and then the filter holder (g - Fig. 2). 4. Fit the carbon filter (i - Fig. 2) in the filter holder (h - Fig. 2) 5. Refit the filter holder (j - Fig. 2) and secure it to the hood with the screw (g - Fig. 2). 6. Refit the grease filter. Carbon filter maintenance: Unlike traditional carbon filters, this carbon filter can be washed and reactivated. With normal hood use, the filter should be cleaned once a month. The filter is best washed in a dishwasher at the highest temperature possible, using a normal dishwasher detergent. To avoid particles of food or dirt settling on the filter during washing and giving rise to unpleasant smells, it is advisable to wash the filter on its own. After washing, dry the filter in the oven at 100° C for 10 minutes to reactivate it. The filter will retain its odour-absorbing capacity for three years, after which it will have to be replaced. f f Fig. 1 j i h Fig. 2 g Replacing bulbs - Fig. 3 1. Unplug the appliance or disconnect the mains power supply. 2. Using a screwdriver or any other suitable tool, prise off the lamp cover. 3. Remove the burnt-out bulb. 4. Replace using 20W max halogen bulbs only, making sure not to touch them with your hands. 5. Replace the lamp cover so that it clicks into position. 5019 100 75182/A D GB F NL E P I GR  Fig. 3
1 / 1

Whirlpool AKR 931 AL-1 Program Chart

Categoría
Campanas de cocina
Tipo
Program Chart