Ubiquiti ER-8-XG Guía del usuario

Ubiquiti
Marca
Ubiquiti
Modelo
ER-8-XG
Categoría
Convertidores de medios de red
Tipo
Guía del usuario
8-Port 10G SFP+ Router
Model: ER-8-XG
Introduction
Thank you for purchasing the Ubiquiti Networks®
EdgeRouter™Infinity. This Quick Start Guide is designed
to guide you through installation and also includes
warrantyterms.
Package Contents
EdgeRouter Infinity
Mounting Brackets
(Qty. 2)
Bracket Screws
(Qty. 8)
Mounting Screws
(Qty. 4)
Cage Nuts
(Qty. 4)
Power Cords
(Qty. 2)
Rubber Feet
(Qty. 4)
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the professional
installer’s responsibility to follow local country regulations, including operation within legal
frequency channels, output power, indoor cabling requirements, and Dynamic Frequency
Selection (DFS) requirements.
Installation Requirements
• Phillips screwdriver (for rack- or wall-mounting)
• Standard-sized, 19" wide rack with a minimum of 1U height
available (for rack-mounting)
• For indoor applications, use Category 5 (or above) UTP
cabling approved for indoor use.
• For outdoor applications, shielded Category 5 (or above)
cabling should be used for all wired Ethernet connections
and should be grounded through the AC ground of the
power supply.
We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial-grade, shielded Ethernet cable from Ubiquiti
Networks. For more details, visit:
www.ubnt.com/toughcable
WARNING: To reduce the risk of fire or electric
shock, do not expose the EdgeRouter Infinity to rain
ormoisture.
Note: Although the cabling can be located outdoors,
the EdgeRouter Infinity itself should be housed inside
a protective enclosure.
Hardware Overview
Front Panel Ports
Console SFP+
(eth1-eth8)
RJ45
(eth0)
USB
microSD
Interface Description
Console
RJ45 serial console port for Command
Line Interface (CLI) management. Use an
RJ45-to-DB9, serial console cable, also
known as a rollover cable, to connect the
Console port to your computer. (If your
computer does not have a DB9 port, then
you will also need a DB9 adapter.) Then
configure the following settings as needed:
• Baud rate 115200
• Data bits 8
• Parity NONE
• Stop bits 1
• Flow control NONE
SFP+
(eth1-eth8)
Hot-swappable SFP+ ports support
10Gbps connections.
RJ45
(eth0)
RJ45 port supports 10/100/1000 Ethernet
connections.
microSD Reserved for future use.
USB Reserved for future use.
Front Panel Button
Reset
Button Description
Reset
There are two methods to reset the
EdgeRouter Infinity to factory defaults:
• Runtime reset (recommended) The
EdgeRouter Infinity should be running
after bootup is complete. Press and hold
the Reset button for about 10seconds
until the LED of port eth0 starts flashing
and then becomes solidly lit. After a few
seconds, the LED will turn off, and the
EdgeRouter Infinity will automatically
reboot.
Note: To press the Reset button,
insert a straightened paper clip (or
similar object) into the hole shown
above. Do not use an object that
can break and become lodged in
the hole.
• Power-on reset Disconnect the Power
Cords from the EdgeRouter Infinity.
Press and hold the Reset button while
connecting the Power Cords to the
EdgeRouter Infinity. The port LEDs will
light up in sequential order. Keep holding
the Reset button until the LED on the
last port starts flashing, and then release
the button.
Front Panel LEDs
SFP+:
Link/Act
RJ45:
Link/Act
System
LED State Status
System
White EdgeRouter Infinity is
powered on.
SFP+ (eth1-8)
Link/Act
Off No Link
White Link Established
White Flashing Link Activity
RJ45 (eth0)
Link/Act
Off No Link
Green Link Established
Green Flashing Link Activity
Back Panel
PSU Power Ports
Fans
Note: There are ventilation holes on the sides of the
EdgeRouter Infinity.
Hardware Installation
The EdgeRouter Infinity can be placed on a horizontal surface,
mounted on a wall, or mounted in a rack.
WARNING: FAILURE TO PROVIDE PROPER VENTILATION
MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF
CLEARANCE NEXT TO THE VENTILATION HOLES FOR
ADEQUATE AIRFLOW.
1. Attach the Mounting Brackets to the EdgeRouter Infinity
using the eight Bracket Screws.
2. Attach the EdgeRouter Infinity to the rack using the four
Mounting Screws. (If the rack has square slots, then use the
Cage Nuts with the Mounting Screws.)
3. Connect the Power Cord to one PSU Power Port.
4. Connect the other end of the Power Cord to a power outlet.
5. Repeat steps 3-4 to connect power to the second
PSUPower Port.
Connecting SFP+
1. Remove the protective plug covering the SFP+ port.
2. Plug a compatible fiber module into the SFP+ port.
1000Mbps SM/SC 20KM DDM
Tx1550nm/Rx1310nm
3. Connect the fiber optic cable to the fiber module. Then
connect the other end of the cable to another fiber device.
4. Repeat steps 1-3 to connect additional SFP+ ports.
Note: Use compatible fiber SFP+ modules with the
appropriate fiber optic cabling. For information about
compatible fiber SFP+ modules, visit:
ubnt.link/SFP_DAC_Compatibility
Accessing the EdgeOS Configuration Interface
The EdgeOS® configuration interface can be accessed via
DHCP or static IP address assignment. By default, eth1 is set
up as a DHCP client, while eth0 is assigned a static IP address
of 192.168.1.1. To configure the EdgeRouter, proceed to the
appropriate section: DHCP or “Static IP Address”.
DHCP
1. Connect a cable from eth1 on the EdgeRouter to a LAN
segment that has an existing DHCP server.
2. To check the IP address of the EdgeRouter, use one of the
following methods:
• Set up the DHCP server to provide a specific IP address
to the EdgeRouter based on its MAC address (on the
label).
• Let the EdgeRouter obtain an IP address and then check
the DHCP server to see which IP address was assigned.
3. Launch your web browser. Enter the appropriate IP address
in the address field. Press enter (PC) or return (Mac).
4. The login screen will appear. Enter ubnt in the Username
and Password fields. Read the Ubiquiti License Agreement,
and check the box next to I agree to the terms of this License
Agreement to accept it. Click Login.
The EdgeOS Configuration Interface will appear, allowing you
to customize your settings as needed. For more information,
refer to the EdgeOS User Guide, which is available at
www.ubnt.com/download/edgemax
You can also manage your device using the Ubiquiti® Network
Management System. UNMS™ lets you configure, monitor,
upgrade, and back up your devices using a single application.
Get started at www.unms.com
Static IP Address
1. Connect an Ethernet cable from the Ethernet port of your
computer to the port labeled eth0 on the EdgeRouter.
2. Configure the Ethernet adapter on your host system with a
static IP address on the 192.168.1.x subnet.
3. Launch your web browser. Type https://192.168.1.1 in the
address field. Press enter (PC) or return (Mac).
https://192.168.1.1
4. The login screen will appear. Enter ubnt in the Username
and Password fields. Read the Ubiquiti License Agreement,
and check the box next to I agree to the terms of this License
Agreement to accept it. Click Login.
The EdgeOS Configuration Interface will appear, allowing you
to customize your settings as needed. For more information,
refer to the EdgeOS User Guide, which is available at
www.ubnt.com/download/edgemax
You can also manage your device using the Ubiquiti Network
Management System. UNMS lets you configure, monitor,
upgrade, and back up your devices using a single application.
Get started at www.unms.com
Specifications
ER-8-XG
Dimensions 442.4 x 285.6 x 43.7 mm
(17.42 x 11.24 x 1.72")
Weight
Without Mount
With Mount
4.950 kg (10.91 lb)
5.045 kg (11.12 lb)
Max. Power Consumption 100W
Power Method 110 - 240VAC
Power Supply (2) Hotswappable AC/DC PSU
Supported Voltage Range AC Input: 100 to 240VAC
Button Reset
Processor MIPS64 16 Core 1.8 GHz
System Memory 16 GB DDR4 RAM
On-Board Flash Storage 8 MB NOR Flash
4 GB eMMC NAND Flash
LEDs
System
SFP+ Data Ports
RJ45 Data Port
Status
Link/Activity
Link/Activity
Interfaces
Serial Console Port
Data Ports
(1) RJ45 Serial Port
(8) SFP+ Ports
(1) RJ45 Gigabit Ethernet Port
Mounting Rack
ESD/EMP Protection Air: ± 24 kV, Contact: ± 24 kV
Operating Temperature -5 to 40° C (23 to 104° F)
Operating Humidity 5 - 95% Noncondensing
Certications CE, FCC, IC
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Failure to provide proper ventilation may
cause fire hazard. Keep at least 20 mm of clearance next
to the ventilation holes for adequate airflow.
WARNING: To reduce the risk of fire or electric shock, do
not expose this product to rain or moisture.
WARNING: Do not use this product in location that can
be submerged by water.
WARNING: Avoid using this product during an electrical
storm. There may be a remote risk of electric shock from
lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a
different power source than those specified may result in improper
operation, damage to the equipment or pose a fire hazard if the
limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service
should be provided only by a qualified service technician.
3. This equipment is provided with a detachable power cord which has
an integral safety ground wire intended for connection to a grounded
safety outlet.
a. Do not substitute the power cord with one that is not the provided
approved type. Never use an adapter plug to connect to a 2-wire
outlet as this will defeat the continuity of the grounding wire.
b. The equipment requires the use of the ground wire as a part of the
safety certification, modification or misuse can provide a shock
hazard that can result in serious injury or death.
c. Contact a qualified electrician or the manufacturer if there
are questions about the installation prior to connecting the
equipment.
d. Protective earthing is provided by Listed AC adapter. Building
installation shall provide appropriate short-circuit backup
protection.
e. Protective bonding must be installed in accordance with local
national wiring rules and regulations.
Limited Warranty
www.ubnt.com/support/warranty/
The limited warranty requires the use of arbitration to resolve disputes on
an individual basis, and, where applicable, specify arbitration instead of
jury trials or class actions.
Compliance
FCC
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operations of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
ISED Canada
CAN ICES-3(A)/NMB-3(A)
This Class A digital apparatus complies with Canadian CAN ICES-003.
CAN ICES-3(A)/NMB-3(A)
Cet appareil numérique de la classe A est conforme à la norme NMB-003
du Canada.
Australia and New Zealand
Warning: This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may
be required to take adequate measures.
CE Marking
CE marking on this product represents the product is in compliance with all
directives that are applicable to it.
RoHS/WEEE Compliance Statement
English
European Directive 2012/19/EU requires that the equipment bearing
this symbol on the product and/or its packaging must not be disposed
of with unsorted municipal waste. The symbol indicates that this
product should be disposed of separately from regular household waste
streams. It is your responsibility to dispose of this and other electric and
electronic equipment via designated collection facilities appointed by the
government or local authorities. Correct disposal and recycling will help
prevent potential negative consequences to the environment and human
health. For more detailed information about the disposal of your old
equipment, please contact your local authorities, waste disposal service, or
the shop where you purchased the product.
Deutsch
Die Europäische Richtlinie 2012/19/EU verlangt, dass technische
Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem
Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall
entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt
von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es
liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische
und elektronische Geräte über die dafür zuständigen und von der
Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu
entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,
potentielle negative Folgen für Umwelt und die menschliche Gesundheit
zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer
Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder
städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das
Produkt erworben haben.
Español
La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en
el propio aparato y/o en su embalaje no deben eliminarse junto con otros
residuos urbanos no seleccionados. El símbolo indica que el producto
en cuestión debe separarse de los residuos domésticos convencionales
con vistas a su eliminación. Es responsabilidad suya desechar este y
cualesquiera otros aparatos eléctricos y electrónicos a través de los puntos
de recogida que ponen a su disposición el gobierno y las autoridades
locales. Al desechar y reciclar correctamente estos aparatos estará
contribuyendo a evitar posibles consecuencias negativas para el medio
ambiente y la salud de las personas. Si desea obtener información más
detallada sobre la eliminación segura de su aparato usado, consulte a las
autoridades locales, al servicio de recogida y eliminación de residuos de su
zona o pregunte en la tienda donde adquirió el producto.
Français
La directive européenne 2012/19/UE exige que l’équipement sur lequel
est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté
avec les autres ordures ménagères. Ce symbole indique que le produit
doit être éliminé dans un circuit distinct de celui pour les déchets des
ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout
autre matériel électrique ou électronique par les moyens de collecte
indiqués par le gouvernement et les pouvoirs publics des collectivités
territoriales. L’élimination et le recyclage en bonne et due forme ont pour
but de lutter contre l’impact néfaste potentiel de ce type de produits
sur l’environnement et la santé publique. Pour plus d’informations sur le
mode d’élimination de votre ancien équipement, veuillez prendre contact
avec les pouvoirs publics locaux, le service de traitement des déchets, ou
l’endroit où vous avez acheté le produit.
Italiano
La direttiva europea 2012/19/UE richiede che le apparecchiature
contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non
siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica
che questo prodotto non deve essere smaltito insieme ai normali rifiuti
domestici. È responsabilità del proprietario smaltire sia questi prodotti sia
le altre apparecchiature elettriche ed elettroniche mediante le specifiche
strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il
corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze
potenzialmente negative per l’ambiente e per la salute dell’essere umano.
Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie
apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti
pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel
quale avete acquistato il prodotto.
Declaration of Conformity
български [Bulgarian] С настоящото UBIQUITI NETWORKS декларира, че това устройство
ER-8-XG е в съответствие със съществените изисквания и други приложими разпоредби на
Директиви 2014/30/ЕС, 2014/35/ЕС. Цялостният текст на ЕС декларацията за съответствие
може да се намери на следния интернет адрес:
www.ubnt.com/compliance
Hrvatski [Croatian] UBIQUITI NETWORKS ovim putem izjavljuje da je ovaj uređaj ER-8-XG
sukladan osnovnim zahtjevima i ostalim bitnim odredbama Direktiva 2014/30/EU,
2014/35/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi:
www.ubnt.com/compliance
Čeština [Czech] UBIQUITI NETWORKS tímto prohlašuje, že toto ER-8-XG zařízení, je ve
shodě se základními požadavky a dalšími příslušnými ustanoveními směrnic 2014/30/EU,
2014/35/EU. Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese:
www.ubnt.com/compliance
Dansk [Danish] Hermed, UBIQUITI NETWORKS, erklærer at denne ER-8-XG enhed,
er i overensstemmelse med de væsentlige krav og øvrige relevante krav i direktiver
2014/30/EU, 2014/35/EU. EU-overensstemmelseserklæringens fulde tekst kan findes på følgende
internetadresse:
www.ubnt.com/compliance
Nederlands [Dutch] Hierbij verklaart UBIQUITI NETWORKS, dat deze ER-8-XG apparaat, in
overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijnen
2014/30/EU, 2014/35/EU. De volledige tekst van de EU-conformiteitsverklaring kan worden
geraadpleegd op het volgende internetadres:
www.ubnt.com/compliance
English
Hereby, UBIQUITI NETWORKS, declares that this ER-8-XG device, is in compliance with
the essential requirements and other relevant provisions of Directives
2014/30/EU, 2014/35/EU
.
The full text of the EU declaration of conformity is available at the following internet address:
www.ubnt.com/compliance
Eesti keel [Estonian] Käesolevaga UBIQUITI NETWORKS kinnitab, et antud ER-8-XG seade,
on vastavus olulistele nõuetele ja teistele asjakohastele sätetele direktiivide 2014/30/EL,
2014/35/EL. ELi vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil:
www.ubnt.com/compliance
Suomi [Finnish] Täten UBIQUITI NETWORKS vakuuttaa, että tämä ER-8-XG laite, on
yhdenmukainen olennaisten vaatimusten ja muiden sitä koskevien direktiivien 2014/30/EU,
2014/35/EU. EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla
seuraavassa internetosoitteessa:
www.ubnt.com/compliance
Français [French] Par la présente UBIQUITI NETWORKS déclare que l’appareil ER-8-XG, est
conforme aux exigences essentielles et aux autres dispositions pertinentes des directives
2014/30/UE, 2014/35/UE. Le texte complet de la déclaration UE de conformité est disponible à
l’adresse internet suivante:
www.ubnt.com/compliance
Deutsch [German] Hiermit erklärt UBIQUITI NETWORKS, dass sich dieses ER-8-XG
Gerät, in Übereinstimmung mit den grundlegenden Anforderungen und den anderen
relevanten Vorschriften der Richtlinien 2014/30/EU, 2014/35/EU befindet. Der vollständige
Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar:
www.ubnt.com/compliance
Ελληνικά [Greek] Δια του παρόντος, UBIQUITI NETWORKS, δηλώνει ότι αυτή η συσκευή ER-8-XG,
είναι σε συμμόρφωση με τις βασικές απαιτήσεις και τις λοιπές σχετικές διατάξεις των οδηγιών
2014/30/EE, 2014/35/EE. Το πλήρες κείμενο της δήλωσης συμμόρφωσης ΕΕ διατίθεται στην
ακόλουθη ιστοσελίδα στο διαδίκτυο:
www.ubnt.com/compliance
Magyar [Hungarian] Ezennel UBIQUITI NETWORKS kijelenti, hogy ez a ER-8-XG készülék
megfelel az alapvető követelményeknek és más vonatkozó 2014/30/EU, 2014/35/EU irányelvek
rendelkezéseit. Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a következő internetes
címen:
www.ubnt.com/compliance
Íslenska [Icelandic] Hér, UBIQUITI NETWORKS, því yfir að þetta ER-8-XG tæki er í samræmi við
grunnkröfur og önnur viðeigandi ákvæði tilskipana 2014/30/ESB, 2014/35/ESB. Fullur texti ESB
samræmisyfirlýsing er að finna á eftirfarandi netfangi:
www.ubnt.com/compliance
Italiano [Italian] Con la presente, UBIQUITI NETWORKS, dichiara che questo dispositivo ER-8-XG,
è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti delle direttive 2014/30/UE,
2014/35/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente
indirizzo Internet:
www.ubnt.com/compliance
Latviešu valoda [Latvian] Ar šo, UBIQUITI NETWORKS, deklarē, ka ER-8-XG ierīce, ir saskaņā ar
būtiskajām prasībām un citiem attiecīgiem noteikumiem Direktīvās 2014/30/ES, 2014/35/ES. Pilns
ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē:
www.ubnt.com/compliance
Lietuvių kalba [Lithuanian] UBIQUITI NETWORKS deklaruoja, kad šis ER-8-XG įrenginys atitinka
esminius reikalavimus ir kitas 2014/30/ES, 2014/35/ES Direktyvų nuostatas. Visas ES atitikties
deklaracijos tekstas prieinamas šiuo interneto adresu:
www.ubnt.com/compliance
Malti [Maltese]
Hawnhekk, UBIQUITI NETWORKS, tiddikjara li dan il-mezz ER-8-XG huwa konformi
mar-rekwiżiti essenzjali u dispożizzjonijiet rilevanti oħrajn ta ‘Direttivi 2014/30/UE, 2014/35/UE.
Id-dikjarazzjoni tal-konformità tista’ tiġi kkonsultata minn www.ubnt.com/compliance
Norsk [Norwegian]
Herved UBIQUITI NETWORKS, erklærer at denne ER-8-XG enheten, er
i samsvar med de grunnleggende kravene og andre relevante bestemmelser i direktivene
2014/30/EU, 2014/35/EU. Den fulle teksten til EU-samsvarserklæringen er tilgjengelig på
følgende internettadresse: www.ubnt.com/compliance
Polski [Polish] Niniejszym, Ubiquiti Networks, oświadcza, że urządzenie ER-8-XG, jest zgodny
z zasadniczymi wymaganiami oraz pozostałymi stosownymi postanowieniami Dyrektyw
2014/30/UE, 2014/35/UE
. Pełny tekst deklaracji zgodności UE jest dostępny pod następującym
adresem internetowym:
www.ubnt.com/compliance
Português [Portuguese] UBIQUITI NETWORKS declara que este dispositivo ER-8-XG, está
conforme com os requisitos essenciais e outras disposições das Directivas
2014/30/UE,
2014/35/UE
. O texto integral da declaração de conformidade está disponível no seguinte
endereço de Internet:
www.ubnt.com/compliance
Română [Romanian] Prin prezenta, UBIQUITI NETWORKS declară că acest dispozitiv ER-8-XG
este în conformitate cu cerințele esențiale și alte prevederi relevante ale Directivelor
2014/30/UE,
2014/35/UE
. Textul integral al declarației UE de conformitate este disponibil la următoarea adresă
internet:
www.ubnt.com/compliance
Slovenčina [Slovak]
Týmto UBIQUITI NETWORKS, prehlasuje, že toto ER-8-XG zariadenie,
je v súlade so základnými požiadavkami a ďalšími relevantnými ustanoveniami smernice
2014/30/EÚ, 2014/35/EÚ
. Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese:
www.ubnt.com/compliance
Slovenščina [Slovenian]
Družba UBIQUITI NETWORKS izjavlja, da je naprava ER-8-XG v
skladu z obveznimi zahtevami in drugimi ustreznimi določbami direktiv 2014/30/EU in
2014/35/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu:
www.ubnt.com/compliance
Español [Spanish] Por medio de la presente UBIQUITI NETWORKS declara que este dispositivo
ER-8-XG, cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o
exigibles de las Directivas
2014/30/UE, 2014/35/UE
. El texto completo de la declaración UE de
conformidad está disponible en la dirección Internet siguiente:
www.ubnt.com/compliance
Svenska [Swedish] Härmed UBIQUITI NETWORKS, intygar att denna ER-8-XG enhet är i
överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som
framgår av direktiven
2014/30/EU, 2014/35/EU
. Den fullständiga texten till EU-försäkran om
överensstämmelse finns på följande webbadress:
www.ubnt.com/compliance
Online Resources
Support help.ubnt.com
Community community.ubnt.com
Downloads downloads.ubnt.com
©2016-2018 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti,
UbiquitiNetworks, the Ubiquiti U logo, the Ubiquiti beam logo, EdgeMAX,
EdgeOS, EdgeRouter, TOUGHCable, and UNMS are trademarks or registered
trademarks of UbiquitiNetworks,Inc. in the United States and in other
countries. All other trademarks are the property of their respective owners. NBAI101818
www.ubnt.com
Ubiquiti Networks, Inc.
685 Third Avenue, 27th Floor
New York, NY 10017
USA
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Ubiquiti ER-8-XG Guía del usuario

Ubiquiti
Marca
Ubiquiti
Modelo
ER-8-XG
Categoría
Convertidores de medios de red
Tipo
Guía del usuario
Descargar PDF
informe

En otros idiomas

Documentos relacionados

Otros documentos