LG 42LE4600 Manual de usuario

Marca: LG

Modelo: 42LE4600

Categoría: Televisores de plasma

Tipo: Manual de usuario

P/NO : MFL59166625 (1009-REV04)

www.lg.com

The model and serial number of the TV is located

on the back and/or one side of the TV.

Record it below should you ever need service.

MODEL

SERIAL

OWNER’S MANUAL

LED LCD TV / LCD TV /

PLASMA TV

Please read this manual carefully before operating

your set and retain it for future reference.

22LE6500

26LE6500

32LE4600

42LE4600

47LE4600

55LE4600

32LD465

37LD465

42LD465

47LD465

32LD420

42LD420

LED LCD TV MODELS

22LE5300

26LE5300

32LE5300

37LE5300

42LE5300

47LE5300

55LE5300

LCD TV MODELS

32LD350

32LD460

37LD460

42LD460

47LD460

37LD461C

42LD461C

PLASMA TV MODELS

42PJ230

50PJ230

42PJ250

50PJ250

42PJ350

50PJ350

32LD420C

42LD420C

32LD460H

42LD460H

32LE4300

42LE4300

WARNING / CAUTION

The lightning flash with arrowhead

symbol, within an equilateral trian-

gle, is intended to alert the user to

the presence of uninsulated “dan-

gerous voltage” within the product’s enclo-

sure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equi-

lateral triangle is intended to alert

the user to the presence of important oper-

ating and maintenance (servicing) instruc-

tions in the literature accompanying the

appliance.

TO REDUCE THE RISK OF ELECTRIC

SHOCK DO NOT REMOVE COVER (OR

BACK). NO USER SERVICEABLE PARTS

INSIDE. REFER TO QUALIFIED SERVICE

PERSONNEL.

SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus

near water.

Clean only with dry cloth.

Do not block any ventilation

openings. Install in accordance

with the manufacturer’s

instructions.

Do not install near any heat

sources such as radiators, heat

registers, stoves, or other appa-

ratus (including amplifiers) that

produce heat.

Protect the power cord from

being walked on or pinched

particularly at plugs, conve-

nience receptacles, and the

point where they exit from the

apparatus.

Only use attachments/acces-

sories specified by the manu-

facturer.

Use only with the cart, stand,

tripod, bracket, or table speci-

fied by the manufacturer, or

sold with the apparatus. When

a cart is used, use caution

when moving the cart/appara-

tus combination to avoid injury

from tip-over.

Unplug this apparatus during

lighting storms or when unused

for long periods of time.

Refer all servicing to qualified service per-

sonnel. Servicing is required when the appa-

ratus has been damaged in any way, such

as power-supply cord or plug is damaged,

liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been

exposed to rain or moisture, does not oper-

ate normally, or has been dropped.

Never touch this apparatus or antenna dur-

ing a thunder or lighting storm.

When mounting a TV on the wall, make sure

not to install the TV by the hanging power

and signal cables on the back of the TV.

Do not allow an impact shock or any objects

to fall into the product, and do not drop

onto the screen with something.

CAUTION concerning the Power Cord:

It is recommend that appliances be placed

upon a dedicated circuit; that is, a single

outlet circuit which powers only that appli-

ance and has no additional outlets or

branch circuits. Check the specification

page of this owner's manual to be certain.

Do not connect too many appliances to the

same AC power outlet as this could result in

fire or electric shock.

Do not overload wall outlets. Overloaded

wall outlets, loose or damaged wall outlets,

extension cords, frayed power cords, or

damaged or cracked wire insulation are

dangerous . Any of these conditions could

result in electric shock or fire. Periodically

examine the cord of your appliance, and if its

appearance indicates damage or deteriora-

tion, unplug it, discontinue use of the appli-

ance, and have the cord replaced with an

exact replacement part by an authorized

servicer. Protect the power cord from phys-

ical or mechanical abuse, such as being

twisted, kinked, pinched, closed in a door, or

walked upon. Pay particular attention to

plugs, wall outlets, and the point where the

cord exits the appliance.

Do not make the TV with the power cord

plugged in. Do not use a damaged or loose

power cord. Be sure do grasp the plug

when unplugging the power cord. Do not

pull on the power cord to unplug the TV.

SAFETY INSTRUCTIONS

WARNING - To reduce the risk

of fire or electrical shock, do not

expose this product to rain,

moisture or other liquids. Do

not touch the TV with wet

hands. Do not install this prod-

uct near flammable objects

such as gasoline or candles or

expose the TV to direct air

conditioning.

Do not expose to dripping or

splashing and do not place

objects filled with liquids, such

as vases, cups, etc. on or over

the apparatus (e.g. on shelves

above the unit).

GROUNDING

Ensure that you connect the earth ground wire

to prevent possible electric shock (i.e. a TV with

a three-prong grounded AC plug must be con-

nected to a three-prong grounded AC outlet). If

grounding methods are not possible, have a

qualified electrician install a separate circuit

breaker.

Do not try to ground the unit by connecting it to

telephone wires, lightening rods, or gas pipes.

Power

Supply

Short-circuit

Breaker

DISCONNECTING DEVICE FROM MAINS

Mains plug is the disconnecting device. The

plug must remain readily operable.

As long as this unit is connected to the AC

wall outlet, it is not disconnected from the AC

power source even if you turn off this unit by

SWITCH.

Cleaning

When cleaning, unplug the power cord and

scrub gently with a soft cloth to prevent

scratching. Do not spray water or other liquids

directly on the TV as electric shock may

occur. Do not clean with chemicals such as

alcohol, thinners or benzene.

Moving

Make sure the product is turned off,

unplugged and all cables have been

removed. It may take 2 or more people to

carry larger TVs. Do not press against or put

stress on the front panel of the TV.

Ventilation

Install your TV where there is proper ventila-

tion. Do not install in a confined space such

as a bookcase. Do not cover the product

with cloth or other materials (e.g.) plastic

while plugged in. Do not install in exces-

sively dusty places.

Take care not to touch the ventilation open-

ings. When watching the TV for a long

period, the ventilation openings may

become hot.

If you smell smoke or other odors coming

from the TV, unplug the power cord and con-

tact and authorized service center.

Do not press strongly upon the

panel with hand or sharp object

such as nail, pencil or pen, or

make a scratch on it.

Keep the product away from direct sunlight.

Dot Defect

The Plasma or LCD panel is a high technol-

ogy product with resolution of two million to

six million pixels. In a very few cases, you

could see fine dots on the screen while

you’reviewing the TV. Those dots are deacti-

vated pixels and do not affect the perfor-

mance and reliability of the TV.

Generated Sound

“Cracking” noise: A cracking noise that occurs

when watching or turning off the TV is gener-

ated by plastic thermal contraction due to

temperature and humidity. This noise is com-

mon for products where thermal deformation

is required.

Electrical circuit humming/panel buzzing: A

low level noise is generated from a high-speed

switching circuit, which supplies a large amount

of current to operate a product. It varies

depending on the product.

This generated sound does not affect the per-

formance and reliability of the product.

For LED LCD TV/LCD TV

If the TV feels cold to the touch, there may be

a small “flicker” when it is turned on. This is

normal, there is nothing wrong with TV.

Some minute dot defects may be visible on

the screen, appearing as tiny red, green, or

blue spots. However, they have no adverse

effect on the monitor’s performance.

Avoid touching the LCD screen or holding your

finger(s) against it for long periods of time.

Doing so may produce some temporary dis-

tortion effects on the screen.

ON DISPOSAL

(Only Hg lamp used LCD TV)

The fluorescent lamp used in this product con-

tains a small amount of mercury. Do not

dispose of this product with general house-

hold waste. Disposal of this product must be

carried out in accordance to the regulations of

your local authority.

CONTENTS

WARNING / CAUTION

..............................2

SAFETY INSTRUCTIONS

........................3

FEATURE OF THIS TV

............................. 8

PREPARATION

Accessories .............................................................9

Front Panel Information ....................................12

Back Panel Information .....................................18

Stand Instructions

.....................................................23

Woofer Installation: When Using The Wall

Mount

...............................................................................30

VESA Wall Mounting .........................................31

Cable Management ..........................................33

Desktop Pedestal Installation ......................... 37

Swivel Stand ........................................................ 37

Attaching the TV to a Desk

......................... 38

Kensington Security System ..........................38

Securing the TV to the wall to prevent falling

when the tv is used on a stand .....................39

Antenna or Cable Connection .......................40

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup .............................................41

DVD SETUP .........................................................44

VCR SETUP .........................................................46

Other A/V Source Setup ................................. 47

USB Connection ................................................48

Headphone Setup .............................................48

Audio Out Connection .....................................49

External Equipment WIreless Connection .50

PC Setup ...............................................................51

WATCHING TV / CHANNEL CONTROL

Remote Control Functions ..............................58

Turning on the TV ..............................................60

Channel Selection..............................................60

Volume Adjustment ..........................................60

Initial Setting ........................................................ 61

On-Screen Menus Selection ..........................63

Quick Menu .........................................................65

Customer Support

- Software Update .............................................66

- Picture Test/Sound Test ................................ 67

- Product/Service Info. .....................................68

Simple Manual ....................................................69

Channel Setup

- Auto Scan (Auto Tuning) ..............................70

- Add/Delete Channel (Manual Tuning) ...... 71

Channel Editing .................................................. 72

Favorite Channel Setup .................................... 73

Favorite Channel List ........................................ 73

Channel List ........................................................ 74

Scan Option ........................................................ 75

System Color ....................................................... 76

Channel Brief Information ............................... 77

EPG (Electronics Program Guide) ................ 79

Input List ..............................................................82

Input Label ...........................................................83

Mode Setting ......................................................84

Demo Mode ........................................................85

Initial Setting (Reset to Factory Default) .....86

AV Mode ............................................................... 87

SIMPLINK .............................................................88

MY MEDIA

Connection Method ..........................................90

Entry Mode ........................................................... 91

Movie list ...............................................................92

Photo list ...............................................................99

Music list .............................................................105

Extra Contents .................................................. 109

DivX Registration Code ................................... 110

Deactivation ..........................................................111

PICTURE CONTROL

Picture Size (Aspect Ratio) Control ............. 112

Picture Wizard .................................................... 114

ꕊ Energy Saving ............................................. 116

Preset Picture Settings (Picture Mode) .......117

Manual Picture Adjustment - User Mode . 118

Picture Impro

vement Technology (Advanced

Control) ................................................................ 119

Expert Picture Control ....................................120

Picture Reset ..................................................... 123

TruMotion ........................................................... 124

Power Indicator ................................................. 125

Image Sticking Minimization (ISM) Method

.126

SOUND & LANGUAGE CONTROL

Auto Volume .......................................................127

Balance ................................................................127

Clear Voice II ..................................................... 128

Preset Sound Settings (Sound Mode) ...... 129

Sound Setting Adjustment - User Mode .130

Audio Reset ........................................................ 131

Digital Audio Out .............................................. 131

TV Speakers On/Off Setup .......................... 132

Stereo/SAP Broadcast Setup ...................... 133

Audio Language ............................................. 134

On-screen Menus Language Selection .... 135

Caption Mode

- Analog Broadcasting System Captions . 136

- Digital Broadcasting System Captions ....137

TIME SETTING

Clock Setting

- Auto Clock Setup ......................................... 138

- Manual Clock Setup .................................... 139

Auto On/Off Time Setting ............................140

Sleep Timer Setting ......................................... 141

PARENTAL CONTROL / RATINGS

Set Password & lock system-

- Setting up Your Password .......................... 142

- Set Password ................................................. 143

- Lock System ................................................... 144

Channel Blocking ............................................. 145

Movie Rating ..................................................... 146

External Input Blocking ...................................147

Key Lock ............................................................. 148

APPENDIX

Troubleshooting ................................................ 149

Maintenance ...................................................... 152

Product Specifications ................................... 153

IR Codes ............................................................. 158

External Control through RS-232C ........... 159

Open Source Software Notice ..................... 165

FEATURE OF THIS TV

ꔛ

Some of these features are not available on all models.

ABOUT DIVX VIDEO: DivX® is a digital

video format created by DivX,Inc. This is

an official DivX Certified device that

plays DivX video. Visit www.divx.com for

more information and software tools to

convert your files into DivX video.

ABOUT DIVX VIDEO-ON-DEMAND:

This DivX Certified® device must be

registered in order to play DivX Video-

on-Demand (VOD) content. To gener-

ate the registration code, locate the

DivX VOD section in the device setup

menu. Go to vod.divx.com with this

code to complete the registration pro-

cess and learn more about DivX VOD.

“DivX Certified® to play DivX® video up

to HD 1080p, including premium con-

tent”

“DivX®, DivX Certified® and associated

logos are registered trademarks of

DivX, Inc. and are used under license.”

Pat. 7,295,673; 7,460,668; 7,515,710;

7,519,274

Manufactured under license from

Dolby Laboratories. “Dolby “and the

double-D symbol are trademarks of

Dolby Laboratories.

HDMI, the HDMI logo and High-

Definition Multimedia Interface are

trademarks or registered trade-

marks of HDMI Licensing LLC."

IMPORTANT INFORMATION TO PREVENT “IMAGE

BURN / BURN-IN” ON YOUR TV SCREEN

ꔛ

When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed

on the TV for an extended period, it can become permanently imprinted on the screen. This

phenomenon is known as “image burn” or “burn-in.” Image burn is not covered under the man-

ufacturer’s warranty.

ꔛ

In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged

period (2 or more hours for LCD, 1 or more

hours for Plasma).

ꔛ

Image burn can also occur on the letter-

boxed areas of your TV if you use the 4:3

aspect ratio setting for an extended period.

ACCESSORIES

PREPARATION

Ensure that the following accessories are included with your TV. If an accessory is missing, please con-

tact the dealer where you purchased the TV.

The accessories included may differ from the images below.

Option Extras

* Wipe spots on the exterior only

with the polishing cloth.

* Do not wipe roughly when remov-

ing stain. Excessive pressure may

cause scratch or discoloration.

Polishing Cloth

Not included with all models

D-sub 15 pin Cable

When using the VGA (D-sub 15

pin cable) PC connection, the

user must use shielded signal

interface cables with ferrite cores

to maintain standards compli-

ance.

1.5V 1.5V

ENERGY

CHVOL

456

SAVING

AV MOD E

INPUT

FAV

RATIO

MUTE

MARK

Q.VIEW

LIST

FREEZE

ENTER

GUIDE

Q.MENU

INFO

BACK

EXIT

Owner’s Manual

Remote Control,

Batteries (AAA)

Plasma TV

Protection Cover

(Refer to P.23 )

Cable Holder

(Refer to P.33)

x 2

Screws for stand assembly

(Refer to P.23)

x 3

(M5 x 14)

x 4

(M4 x 28)

Power Cord

32LD350, 32/37/42/47LD460, 37/42LD461C, 32/37/42/47LD465, 32/42LD460H

Screws for stand assembly

(Refer to P.24)

Screw for stand fixing

(Refer to P.38)

Protection Cover

(Refer to P.24)

x 8

(M4 x 20)

(Except 47LD460,

47LD465)

Power Cord

32/42LD420, 32/42LD420C

Protection Cover

(Refer to P.25)

Power CordScrews for stand assembly

(Refer to P.25)

Screw for stand fixing

(Refer to P.38)

(M4 x 24)

x 4

RF Adapter (Some models)

You must connect it to the

antenna wire after fixing in

Antenna Input. This adapter is

for supplied in Argentina.

PREPARATION

22/26LE5300

Cable Tie

(Refer to p.36)

AC/DC Adaptor

Power Cord

Ring spacers

(Refer to p.32)

x 4

(For 26LE5300)

Screws for stand assembly

(Refer to P.26, 28)

x 4

(M4 x 14) (M4 x 20)

x 4

(For 26LE5300)

32/37/42/47/55LE5300, 32/42/47/55LE4600

32/37/42/47/55LE5300, 32/42/47/55LE4600, 32/42LE4300

Cable Holder

(Refer to p.36)

Component gender cable,

AV gender cable

x 2

Screw for stand fixing

(Refer to P.38)

(For 32LE5300,

32/42/47/55LE4600,

32LE4300)

Screws for stand assembly

(Refer to P.28)

x 4

(M4 x 16)

x 4

(M4 x 22)

(32LE5300,

32/42/47/55LE4600,

32LE4300)

x 4

(M4 x 26)

(47/55LE5300)

x 4

(M4 x 24)

(37/42LE5300,

42LE4300)

x 2

Woofer PEM nut

(Refer to P.30)

Woofer Fixing Screw

(Refer to P.30)

22/26LE6500

Cable Tie

(Refer to p.35)

AC/DC Adaptor

Power Cord

Screws for stand assembly

(Refer to P.27)

x 2

(M4 x 16)

(32/42/47/55LE4600)

PREPARATION

OPTIONAL EXTRAS (FOR 32/37/42/47/55LE5300, 32/42LE4300)

Optional extras can be changed or modified for quality improvement without any notification.

Contact your dealer for buying these items.

This device only works with compatible LG LED LCD TV, LCD TV, or Plasma TV.

Wireless Media Box

(AN-WL100W)

PREPARATION

ꔛ

Image shown may differ from your TV.

Plasma TV

FRONT PANEL INFORMATION

42/50PJ230, 42/50PJ250

ENTER

VOL

INPUT

SPEAKER

Remote Control Sensor

Intelligent Sensor

Adjusts picture accord-

ing to the surrounding

conditions

Touch Button

You can operate the button just by touching the button lightly with your finger.

ENTER

VOL

INPUT

CHANNEL

(

ꕌ,ꕍ)

Buttons

VOLUME

(+, -)

Buttons

ENTER

Button

INPUT

Button

POWER

Button

Power/Standby Indicator

Illuminates red in standby mode.

The lighting is off while the TV remains on.

42/50PJ350

ENTER

VOL

INPUT

SPEAKER

Remote Control Sensor

Intelligent Sensor

Adjusts picture accord-

ing to the surrounding

conditions

Touch Button

You can operate the button just by touching the button lightly with your finger.

ENTER

VOL

INPUT

CHANNEL

(

ꕌ,ꕍ)

Buttons

VOLUME

(+, -)

Buttons

ENTER

Button

INPUT

Button

POWER

Button

Power/Standby Indicator

Illuminates red in standby mode.

The lighting is off while the TV remains on.

PREPARATION

32LD350

VOL

ENTER

INPUT

CHANNEL

(

ꕌ,ꕍ) Buttons

VOLUME (+, -)

Buttons

ENTER Button

MENU Button

INPUT Button

POWER Button

SPEAKER

Remote Control Sensor

Power/Standby Indicator

(Can be adjusted using the Power Indicator

in the OPTION menu.

►p.125)

PREPARATION

32/37/42/47LD460, 37/42LD461C, 32/37/42/47LD465, 32/42LD460H

VOL

ENTER

INPUT

CHANNEL

(

ꕌ,ꕍ) Buttons

VOLUME (+, -)

Buttons

ENTER Button

MENU Button

INPUT Button

POWER Button

SPEAKER

Remote Control Sensor

Power/Standby Indicator

(Can be adjusted using the Power Indicator in

the OPTION menu.

►p.125)

ꔛ

Image shown may differ from your TV.

PREPARATION

32/42LD420, 32/42LD420C

INPUT

ENTER

VOL

CHANNEL

(▲,▼) Buttons

VOLUME (+, -)

Buttons

ENTER Button

MENU Button

INPUT Button

POWER Button

SPEAKER

Remote Control Sensor

Power/Standby Indicator

(Can be adjusted using the Power Indicator

in the OPTION menu.

►p.125)

PREPARATION

22/26/32/37/42/47/55LE5300

SPEAKER

Power/Standby Indicator

(Can be adjusted using the Power Indicator

in the OPTION menu.

►p.125)

Remote Control Sensor

22/26LE5300

Power/Standby Indicator

(Can be adjusted using the Power Indicator in

the OPTION menu.

►p.125)

Remote Control Sensor

Intelligent Sensor

Adjusts picture according to

the surrounding conditions

32/37/42/47/55LE5300

VOL ENTERCH MENU INPUT

CHANNEL

(

ꕍ,ꕌ)

Buttons

VOLUME

(-, +)

Buttons

ENTER

Button

INPUT

Button

POWER

Button

VOL ENTERCH MENU INPUT

CHANNEL

(

ꕍ,ꕌ)

Buttons

VOLUME

(-, +)

Buttons

ENTER

Button

INPUT

Button

POWER

Button

22/26LE5300

32/37/42/47/55LE5300

ꔛ

Image shown may differ from your TV.

PREPARATION

22/26LE6500

32/42/47/55LE4600, 32/42LE4300

SPEAKER

Power/Standby Indicator

(Can be adjusted using the Power Indicator

in the OPTION menu.

►p.125)

Remote Control Sensor

SPEAKER

Remote Control Sensor

WOOFER

(Except 32/42LE4300)

Power/Standby Indicator

(Can be adjusted using the Power Indicator

in the OPTION menu.

►p.125)

Intelligent Sensor

Adjusts picture accord-

ing to the surrounding

conditions.

ENTER

INPUT

VOL

ENTER Button

MENU Button

INPUT Button

POWER Button

CHANNEL

(▲,▼) Buttons

VOLUME (+, -)

Buttons

VOL ENTERCH MENU INPUT

CHANNEL

(

ꕍ,ꕌ)

Buttons

VOLUME

(-, +)

Buttons

ENTER

Button

INPUT

Button

POWER

Button

PREPARATION

BACK PANEL INFORMATION

ꔛ

Image shown may differ from your TV.

ANTENNA IN CABLE IN

VIDEO

AUDIO

L(MONO)

VIDEO

AUDIO

RGB IN (PC)

RS-232C IN

(

CONTROL&SERVICE)

AUDIO IN

(RGB/DVI)

OPTICAL DIGITAL

AUDIO OUT

/DVI IN

AV IN 1

COMPONENT IN

ANTENNA IN CABLE IN

VIDEO

AUDIO

L(MONO)

VIDEO

AUDIO

RS-232C IN

(

CONTROL&SERVICE)

OPTICAL DIGITAL

AUDIO OUT

AV IN

COMPONENT IN

SERVICE

ONLY

IN 2

USB IN

AV IN 2

VIDEO

AUDIO

L(MONO)

42/50PJ230

42/50PJ250, 42/50PJ350

411

PREPARATION

32LD350, 32/37/42/47LD460, 37/42LD461C, 32/37/42/47LD465, 32/42LD420, 32/42LD420C,

32/42LD460H

32LD350

32/37/42/47LD460,

37/42LD461C,

32/37/42/47LD465,

32/42LD420,

32/42LD420C,

32/42LD460H

AC IN

VIDEO

AUDIO

RGB IN (PC)

AUDIO IN

(RGB/DVI)

RS-232C IN

(

CONTROL&SERVICE)

OPTICAL

DIGITAL

AUDIO OUT

/DVI IN

ANTENNA

CABLE IN

L R

VIDEO

AUDIO

L/MONO

COMPONENT IN

AV IN 1

IN 2

H/P USB IN

SERVICE ONLY

AV IN 2

VIDEO

AUDIO

L/MONO

IN 2

H/P USB IN

AV IN 2

VIDEO

AUDIO

L/MONO

432

1 1

10 10

11 9

3 3

PREPARATION

H/P

USB IN

IN 3

22/26LE5300, 22/26LE6500

22LE5300

H/P USB IN

26LE5300

H/P USB IN

IN 3

ANTENNA

DC-IN

CABLE IN

RGB IN (PC)

AUDIO IN

RGB/DVI

(DVI)

OPTICAL

DIGITAL

AUDIO OUT

/DVI IN

VIDEO

AUDIO

L(MONO)

VIDEO

AUDIO

YPB PR

L R

COMPONENT IN

AV IN

RS-232C IN

(

CONTROL&SERVICE)

1 2

13 1 27 4

Power Connection

Connect the AC/DC adapter plug to the

power input jack on the TV.

Connect the power cord to the AC/DC

adapter first, then plug the power cord into

the wall power outlet.

CAUTION

► Please be sure to connect the TV to the AC/DC power adapter before connecting the TV’s

power plug to a wall power outlet.

DC INDC IN

AC/DC Adaptor

22/26LE6500

PREPARATION

32/37/42/47/55LE5300, 32/42/47/55LE4600,

32/42LE4300

32/37/42/47/55LE5300

COMPONENT IN2

Y P

B PR / AUDIO

IN 4

H/P

USB IN

AV IN2

VIDEO / AUDIO

CAUTION

For HDMI IN 3, 4 and USB IN

► For an optimal connection,

HDMI cables and USB

devices should have bezels

less than 10 mm (0.39

inches) thick.

*A 10 mm (0.39 inches)

(RGB/DVI)

(DVI)

/DVI IN

AUDIO IN

WIRELESS

CONTROL

ꔡ

RGB IN (PC)

RS-232C IN

(CONTROL &

SERVICE)

OPTICAL

DIGITAL

AUDIO OUT

VIDEO

AUDIO

L/MONO

VIDEO

AUDIO

COMPONENT IN 1

AV IN 1

YPB PR

L R

ANTENNA

CABLE IN

1 7 2 4

6 58

(RGB/DVI)

/DVI IN

(DVI)

AUDIO IN

RGB IN (PC)

RS-232C IN

(CONTROL &

SERVICE)

OPTICAL

DIGITAL

AUDIO OUT

VIDEO

AUDIO

L/MONO

VIDEO

AUDIO

COMPONENT IN 1

AV IN 1

L R

ANTENNA

CABLE

1 7 2 4

6 5

32/37/42/47/55LE5300

32/42/47/55LE4600

32/42/47/55LE4600,

32/42LE4300

COMPONENT IN2

Y P

B PR / AUDIO

IN 3

H/P

USB IN

AV IN2

VIDEO / AUDIO

32/37/42/47/55LE5300

32/42LE4300

(RGB/DVI)

/DVI IN

(DVI)

AUDIO IN

RGB IN (PC)

RS-232C IN

(CONTROL &

SERVICE)

OPTICAL

DIGITAL

AUDIO OUT

VIDEO

AUDIO

L/MONO

VIDEO

AUDIO

COMPONENT IN 1

AV IN 1

L R

ANTENNA

CABLE

WIRELESS

CONTROL

1 7 2 4

6 5

PREPARATION

HDMI/DVI IN, HDMI IN

Digital Connection.

Supports HD video and Digital audio. Doesn’t

support 480i.

Accepts DVI video using an adapter or HDMI

to DVI cable (not included).

OPTICAL DIGITAL AUDIO OUT

Digital optical audio output for use with amps

and home theater systems.

Note: In standby mode, this port doesn’t work.

AV (Audio/Video) IN

Analog composite connection. Supports stan-

dard definition video only (480i).

RS-232C IN (CONTROL & SERVICE) PORT

Used by third party devices.

This port is used for service or Hotel mode.

ANTENNA IN/CABLE IN

Connect over-the air signals to this jack.

Connect cable signals to this jack.

COMPONENT IN

Analog Connection.

Supports HD.

Uses a red, green, and blue cable for video &

red and white for audio.

RGB IN (PC)

Analog PC Connection. Uses a D-sub 15 pin

cable (VGA cable).

AUDIO IN (RGB/DVI)

1/8” (0.32 cm) headphone jack for analog PC

audio input.

WIRELESS CONTROL

Connect the Wireless Dongle to the TV to

control the external input devices connected

to Media Box wirelessly.

USB INPUT

Used for viewing photos, movies and listen-

ing to MP3s.

HEADPHONE INPUT

0.32 cm (1/8 inch) headphone jack

Impedance 16 Ω , Maximum audio out 15 mW

SERVICE ONLY, USB IN SERVICE ONLY

This port is used for service.

Power Cord or Socket

For operation with AC power.

Caution: Never attempt to operate the TV on

DC power.

DC IN

PREPARATION

STAND INSTRUCTIONS

(For Plasma TV)

ꔛ

Image shown may differ from your TV.

INSTALLATION

NOTE

► When assembling the desk type stand,

make sure the screws are fully tightened (If

not tightened fully, the TV can tilt forward

after the product installation). Do not over

tighten.

Carefully place the TV screen side down

on a cushioned surface to protect the

screen from damage.

Assemble the parts of the STAND BODY

with the STAND BASE of the TV.

Assemble the TV as shown.

Fix the 4 screws securely using the holes

in the back of the TV.

STAND BASE

STAND BODY

M5 x 14

M4 x 28

DETACHMENT

PROTECTION COVER

After removing the stand, install the included

PROTECTION COVER over the hole for the

stand.

Press the PROTECTION COVER into the TV

until you hear it click.

When installing the wall mounting bracket, use

the PROTECTION COVER.

Carefully place the TV screen side down

on a cushioned surface to protect the

screen from damage.

Remove the screws that hold the stand on.

Detach the stand from TV.

PROTECTION COVER

Fix a guide to the outside.

PREPARATION

STAND INSTRUCTIONS

(For 32LD350, 32/37/42/47LD460, 37/42LD461C, 32/37/42/47LD465, 32/42LD460H)

ꔛ

Image shown may differ from your TV.

NOTE

► When assembling the desk type stand,

make sure the screws are fully tightened

(If not tightened fully, the TV can tilt for-

ward after the product installation). Do

not over tighten.

Carefully place the TV screen side down on

a cushioned surface to protect the screen

from damage.

Assemble the parts of the STAND BODY

with the STAND BASE of the TV.

Assemble the TV as shown.

Fix the 4 screws securely using the holes in

the back of the TV.

INSTALLATION

STAND BASE

STAND BODY

M4 x 20

DETACHMENT

PROTECTION COVER

After removing the stand, install the included

PROTECTION COVER over the hole for the

stand.

Press the PROTECTION COVER into the TV

until you hear it click.

Carefully place the TV screen side down

on a cushioned surface to protect the

screen from damage.

Remove the screws that hold the stand

on.

Detach the stand from TV.

PREPARATION

STAND INSTRUCTIONS (For 32/42LD420, 32/42LD420C)

ꔛ

Image shown may differ from your TV.

Carefully place the TV screen side down

on a cushioned surface to protect the

screen from damage.

Assemble the TV as shown.

Install the 4 screws into the holes shown.

INSTALLATION

NOTE

► When assembling the desk type stand,

make sure the screws are fully tightened

(If not tightened fully, the TV can tilt for-

ward after the product installation). Do not

over tighten.

M4 x 24

DETACHMENT

PROTECTION COVER

After removing the stand, install the included

PROTECTION COVER over the hole for the

stand.

Press the PROTECTION COVER into the TV until

you hear it click.

When installing the wall mounting bracket, use

the PROTECTION COVER.

Carefully place the TV screen side down on

a cushioned surface to protect the screen

from damage.

Remove the screws that hold the stand on.

Detach the stand from TV.

PREPARATION

STAND INSTRUCTIONS

(For 22LE5300)

ꔛ

Image shown may differ from your TV.

INSTALLATION

NOTE

► When assembling the desk type stand,

make sure the screws are fully tightened (If

not tightened fully, the TV can tilt forward

after the product installation). Do not over

tighten.

Carefully place the TV screen side down

on a cushioned surface to protect the

screen from damage.

Assemble the parts of the STAND BODY

with the STAND BASE of the TV.

Assemble the TV as shown.

Fix the 4 screws securely using the holes

in the back of the TV.

STAND BASE

STAND BODY

M4 x 14

DETACHMENT

Carefully place the TV screen side down

on a cushioned surface to protect the

screen from damage.

Remove the screws that hold the stand

on.

Detach the stand from TV.

PREPARATION

STAND INSTRUCTIONS

(For

22/26LE6500

)

ꔛ

Image shown may differ from your TV.

Carefully place the TV screen side down

on a cushioned surface to protect the

screen from damage.

Assemble the TV as shown.

Install the 2 screws into the holes shown.

INSTALLATION

NOTE

► When assembling the desk type stand,

make sure the screws are fully tightened (If

not tightened fully, the TV can tilt forward

after the product installation). Do not over

tighten.

M4 x 16

DETACHMENT

Carefully place the TV screen side down

on a cushioned surface to protect the

screen from damage.

Remove the screws that hold the stand on.

Detach the stand from TV.

PREPARATION

STAND INSTRUCTIONS

(For 26/32/37/42/47/55LE5300, 32/42/47/55LE4600, 32/42LE4300)

ꔛ

Image shown may differ from your TV.

INSTALLATION

NOTE

► When assembling the desk type stand,

make sure the screws are fully tightened (If

not tightened fully, the TV can tilt forward

after the product installation). Do not over

tighten.

Assemble the parts of the STAND BODY

with the STAND BASE of the TV.

Assemble the TV as shown.

Carefully place the TV screen side down on

a cushioned surface to protect the screen

from damage.

Assemble the part of the STAND

REAR COVER with the TV.

Install the 4 screws into the holes shown.

STAND BASE

STAND BODY

STAND REAR

COVER

M4 x 22 M4 x 24 M4 x 26M4 x 20

M4 x 16M4 x 14

For 26LE5300

26LE5300

Other models

32LE5300,

32/42/47/55LE4600,

32LE4300

37/42LE5300,

42LE4300

47/55LE5300

PREPARATION

DETACHMENT

Carefully place the TV screen side down on

a cushioned surface to protect the screen

from damage.

Remove the screws that hold the stand on.

Detach the STAND REAR COVER from TV.

Detach the stand from TV.

PREPARATION

WOOFER INSTALLATION: WHEN USING THE WALL

MOUNT (For 32/42/47/55LE4600)

Carefully place the TV screen side down

on a cushioned surface to protect the

screen from damage.

Remove the screws from the TV.

Detach the STAND REAR COVER and

STAND from TV.

Detach the WOOFER from the stand.

Assemble the WOOFER with the TV.

Turn the PEM nut for the woofer using a

flathead driver and install the 2 screws as

shown.

When installing the woofer in the TV, make

sure that the power cord is not twisted,

bent or pinched.

PREPARATION

VESA WALL MOUNTING

Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building mate-

rials, please contact your nearest installer.

If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.

We recommend that you use an LG brand wall mount when mounting the TV to a wall.

LG recommends that wall mounting be performed by a qualified professional installer.

Model

VESA (A

Standar Screw Quantity

Wall Mounting Bracket

(sold separately)

22LE5300,

22LE6500,

26LE5300,

26LE6500

100

100 M4 4

LSW100B, LSW100BG

32LD350,

32LD420,

32LD420C,

32LD460,

32LD465,

32LD460H,

32LE5300,

32LE4600,

32LE4300

200

100 M4 4

LSW100B, LSW100BG

37LD460,

37LD461C,

37LD465,

37LE5300,

42LD460,

42LD461C,

42LD465,

42LD420,

42LD420C,

42LD460H,

42LE5300,

42LE4600,

42LE4300,

47LD460,

47LD465,

47LE5300,

47LE4600

200

200 M6 4

LSW200B, LSW200BG

55LE5300,

55LE4600

400

400 M6 4

LSW400B, LSW400BG,

DSW400BG

42/50PJ230,

42/50PJ250,

42/50PJ350

400

400 M6 4

PSW400B PSW400BG

PREPARATION

CAUTION

► Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to

electric shock.

NOTE

► Screw length needed depends on the wall

mount used. For further information, refer to

the instructions included with the mount.

► Standard dimensions for wall mount kits are

shown in the table.

► When purchasing our wall mount kit, a detailed

installation manual and all parts necessary for

assembly are provided.

► Do not use screws longer than the standard

dimension, as they may cause damage to the

inside to the TV.

► For wall mounts that do not comply with the

VESA standard screw specifications, the length

of the screws may differ depending on their

specifications.

► Do not use screws that do not comply with the

VESA standard screw specifications.

Do not use fasten the screws too strongly, this

may damage the TV or cause the TV to a fall,

leading to personal injury. LG is not liable for

these kinds of accidents.

► LG is not liable for TV damage or personal

injury when a non-VESA or non specified wall

mount is used or the consumer fails to follow

the TV installation instructions.

Place the on the set before installing the wall mounting

bracket so that the inclination of the backside of the set

can be adjusted perpendicularly.

For 26LE5300

4-RING SPACERS

ꔛ

Image shown may differ from your TV.

For 32/42/47/55LE4600

3.6 cm (1.4 inches)

1 cm (0.4 inches)

WOOFER

The clearance from the wall is 3.6 cm (1.4 inches) for this

product.

PREPARATION

CABLE MANAGEMENT

Plasma TV

ꔛ

Image shown may differ from your TV.

CABLE HOLDER

After connecting the cables as necessary,

install the CABLE HOLDER as shown

and bundle the cables.

PREPARATION

32LD350, 32/37/42/47LD460, 37/42LD461C, 32/37/42/47LD465, 32/42LD460H

ꔛ

Image shown may differ from your TV.

Connect the cables as necessary.

To connect additional equipment, see the

EXTERNAL EQUIPMENT SETUP section.

Open the CABLE MANAGEMENT CLIP

as shown.

Put the cables inside the CABLE

MANAGEMENT CLIP and snap it closed.

AC IN

CABLE MANAGEMENT CLIP

PREPARATION

32/42LD420, 32/42LD420C

Connect the cables as necessary.

To connect additional equipment, see the

EXTERNAL EQUIPMENT SETUP section.

Open the CABLE MANAGEMENT CLIP as

shown.

Put the cables inside the CABLE

MANAGEMENT CLIP and snap it closed.

22/26LE6500

After connecting the cables as necessary,

install the CABLE TIE as shown and bundle

the cables.

CABLE MANAGEMENT CLIP

CABLE TIE

PREPARATION

ꔛ

Image shown may differ from your TV.

CABLE HOLDER

After connecting the cables as necessary,

install CABLE HOLDER as shown and

bundle the cables.

Secure the power cord with the CABLE

HOLDER on the TV back cover.

It will help prevent the power cable from

being removed by accident.

32/37/42/47/55LE5300, 32/42/47/55LE4600, 32/42LE4300

22/26LE5300

After connecting the cables as necessary,

install CABLE TIE as shown and bundle

the cables.

CABLE TIE

PREPARATION

DESKTOP PEDESTAL INSTALLATION

SWIVEL STAND

(Except

22LE5300, 22LE6500

)

After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees

to suit your viewing position.

ꔛ

Image shown may differ from your TV.

For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.

4 inches

CAUTION

► Ensure adequate ventilation by following the clearance recommendations.

► Do not mount near or above any type of heat source.

PREPARATION

ATTACHING THE TV TO A DESK

(For 32LD350, 32/37/42LD460, 37/42LD461C, 32/37/42LD465, 32LE5300, 32/42LD420,

32/42LD420C, 32/42/47/55LE4600, 32LE4300, 32/42LD460H)

The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, poten-

tially causing injury or damaging the product.

1-Screw

( provided as parts of the product)

Desk

Stand

KENSINGTON SECURITY SYSTEM

ꔛ

This feature is not available for all models.

- The TV is equipped with a Kensington Security System con-

nector on the back panel. Connect the Kensington Security

System cable as shown below.

- For the detailed installation and use of the Kensington Security

System, refer to the user’s guide provided with the Kensington

Security System.

For further information, contact http://www.kensington.com,

the internet homepage of the Kensington company. Kensington

sells security systems for expensive electronic equipment such

as notebook PCs and LCD projectors.

NOTE: The Kensington Security System is an optional accessory.

WARNING

► To prevent TV from falling over, the TV should be securely attached to the floor/wall per installa-

tion instructions. Tipping, shaking, or rocking the machine may cause injury.

PREPARATION

SECURING THE TV TO THE WALL TO PREVENT FALLING

WHEN THE TV IS USED ON A STAND

We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.

Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward

direction, potentially causing injury or damaging the product.

Caution: Please make sure that children don’t climb on or hang from the TV.

ꔛ

Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the

picture.

* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the

bolts.

* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket

that is mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

ꔛ

Use a sturdy rope (sold separately) to tie the product. It is safer to tie the

rope so it becomes horizontal between the wall and the product.

ꔛ

You should purchase necessary components to prevent the TV from tipping over (when not using a

wall mount).

ꔛ

Image shown may differ from your TV.

NOTE

► Use a platform or cabinet strong enough and large enough to support the size and weight of

the TV.

► To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are

the same.

PREPARATION

ANTENNA OR CABLE CONNECTION

ꔛ

To prevent damage do not connect to the power outlet until all connections are made between the

devices.

ꔛ

Image shown may differ from your TV.

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box

Connections.

For optimum picture quality, adjust antenna direction if needed.

2. Cable

Wall

Antenna

Socket

Outdoor

Antenna

(VHF, UHF)

Cable TV

Wall Jack

Multi-family Dwellings/Apartments

(Connect to wall antenna socket)

RF Coaxial Wire (75 Ω)

Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna)

Be careful not to bend the copper wire

when connecting the antenna.

Copper Wire

ꔛ

To improve the picture quality in a poor signal area, please purchase a signal amplifier and install

properly.

ꔛ

If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

ꔛ

If the antenna is not installed properly, contact your dealer for assistance.

ANTENNA IN CABLE IN

EXTERNAL EQUIPMENT SETUP

HD RECEIVER SETUP

ꔛ

To prevent the equipment damage, never plug in any power cords until you have finished connecting all

equipment.

ꔛ

mage shown may differ from your TV.

Y, C

B/PB, CR/PR

1. How to connect

Connect the video outputs

(

Y, P B, PR

)

of the

digital set-top box to the COMPONENT IN

VIDEO 1 or 2* jacks on the TV. Match the jack

colors (Y = green, P

B = blue, and PR = red).

Connect the audio output of the digital set-top

box to the COMPONENT IN AUDIO 1 or 2*

jacks on the TV.

2. How to use

ꔛ

Turn on the digital set-top box.

(

Refer to the owner’s manual for the digital set-top

box operation.

)

ꔛ

Select the Component, Component1 or

Component2* input source on the TV using the

INPUT button on the remote control.

Component Connection

This TV can receive digital over-the-air/digital cable signals without an external digital set-top box.

However, if you do receive digital signals from a digital set-top box or other digital external device.

Resolution

Horizontal

Frequency

(

KHz

)

Vertical

Frequency

(

)

720x480i

15.73 59.94

15.73 60.00

720x480p

31.47 59.94

31.50 60.00

1280x720p

44.96 59.94

45.00 60.00

1920x1080i

33.72 59.94

33.75 60.00

1920x1080p

26.97 23.976

27.00 24.00

33.71 29.97

33.75 30.00

67.432 59.94

67.50 60.00

EXTERNAL EQUIPMENT SETUP

ANTENNA

RGB IN (PC)

AUDIO IN

RGB/DVI

(DVI)

OPTICAL

DIGITAL

AUDIO OUT

/DVI IN

AV IN

RS-232C IN

(

CONTROL&SERVICE)

1 2

VIDEO

AUDIO

L(MONO)

VIDEO

AUDIO

L R

COMPONENT IN

Y L RP

* Component2: For Plasma TV, 32/37/42/47/55LE5300,

32/42/47/55LE4600, 32/42LE4300

H/P

AV IN2

VIDEO / AUDIO

Y P

AUDIO

COMPONENT IN2

Y LRP

For 32/37/42/47/55LE5300,

32/42/47/55LE4600, 32/42LE4300

EXTERNAL EQUIPMENT SETUP

HDMI Connection

1. How to connect

Connect the digital set-top box to HDMI/DVI IN

1, 2, 3*, or 4** jack on the TV.

No separate audio connection is necessary.

HDMI supports both audio and video.

2. How to use

ꔛ

Turn on the digital set-top box.

(

Refer to the owner’s manual for the digital set-

top box.

)

ꔛ

Select the HDMI, HDMI1, HDMI2 HDMI3*, or

HDMI4** input source on the TV using the INPUT

button on the remote control.

NOTE

► If an HDMI cable doesn’t support High Speed HDMI,

it can cause flickers or no screen display. In this case

use the latest cables that support High Speed HDMI.

► HDMI Audio Supported Format: Dolby Digital (32 KHz, 44.1

KHz, 48 KHz), Linear PCM (32 KHz, 44.1 KHz, 48 KHz)

HDMI-DTV

Resolution

Horizontal

Frequency

(

KHz

)

Vertical

Frequency

(

)

720x480p

31.47 59.94

31.50 60.00

1280x720p

44.96 59.94

45.00 60.00

1920x1080i

33.72 59.94

33.75 60.00

1920x1080p

26.97 23.976

27.00 24.00

33.71 29.97

33.75 30.00

67.432 59.94

67.50 60.00

DC-IN

RGB IN (PC)

AUDIO IN

RGB/DVI

OPTICAL

DIGITAL

AUDIO OUT

COMPONENT IN

AV IN

RS-232C IN

(

CONTROL&SERVICE)

VIDEO

AUDIO

L(MONO)

VIDEO

AUDIO

L R

(DVI)

/DVI IN

1 2

HDMI OUTPUT

* HDMI3: For 26LE5300, 22/26LE6500,

32/42/47/55LE4600, 32/42LE4300

** HDMI4: For 32/37/42/47/55LE5300

EXTERNAL EQUIPMENT SETUP

DVI to HDMI Connection

1. How to connect

Connect the DVI output of the digital set-top

box to the HDMI/DVI IN or 1 jack on the TV.

Connect the digital set-top box audio output to

the AUDIO IN

(

RGB/DVI

)

jack on the TV.

2. How to use

ꔛ

Turn on the digital set-top box.

(

Refer to the owner’s manual for the digital set-

top box.

)

ꔛ

Select the HDMI or HDMI1 input source on the TV

using the

INPUT

button on the remote control.

NOTE

► A DVI to HDMI cable or adapter is required for this con-

nection. DVI doesn't support audio, so a separate audio

connection is necessary.

DC-IN

RGB IN (PC)

AUDIO IN

RGB/DVI

OPTICAL

DIGITAL

AUDIO OUT

COMPONENT IN

AV IN

RS-232C IN

(

CONTROL&SERVICE)

VIDEO

AUDIO

L(MONO)

VIDEO

AUDIO

L R

(DVI)

/DVI IN

1 2

L R

DVI OUTPUT

AUDIO

EXTERNAL EQUIPMENT SETUP

DVD SETUP

1. How to connect

Connect the video outputs

(

Y, P B, PR

)

of the

DVD to the COMPONENT IN VIDEO 1 or 2 *

jacks on the TV.

Match the jack colors

(

Y = green, P

B = blue, and

R = red

)

Connect the audio outputs of the DVD to the

COMPONENT IN AUDIO 1 or 2 * jacks on the

TV.

2. How to use

ꔛ

Turn on the DVD player, insert a DVD.

ꔛ

Select the Component, Component1 or

Component2* input source on the TV using the

INPUT button on the remote control.

ꔛ

Refer to the DVD player’s manual for operating

instructions.

Component Connection

RGB IN (PC)

WIRELESS

CONTROL

AUDIO IN

(RGB/DVI)

RS-232C IN

(

CONTROL&SERVICE)

OPTICAL

DIGITAL

AUDIO OUT

AV IN 1

VIDEO

AUDIO

L(MONO)

VIDEO

AUDIO

COMPONENT IN

L R

Y L RP

ANTENNA

* Component2: For Plasma TV, 32/37/42/47/55LE5300,

32/42/47/55LE4600, 32/42LE4300

Component Input ports

To get better picture quality, connect a DVD

player to the component input ports as shown

below.

Component ports on

the TV

YPB PR

Video output ports

on DVD player

YPB PR

YB-YR-Y

YCbCr

YPbPr

H/P

AV IN2

VIDEO / AUDIO

Y P

AUDIO

COMPONENT IN2

Y LRP

For 32/37/42/47/55LE5300,

32/42/47/55LE4600, 32/42LE4300

EXTERNAL EQUIPMENT SETUP

Composite (RCA) Connection

1. How to connect

Connect the AUDIO/VIDEO jacks between TV

and DVD. Match the jack colors (Video = yellow,

Audio Left = white, and Audio Right = red)

2. How to use

ꔛ

Turn on the DVD player, insert a DVD.

ꔛ

Select the AV, AV1 or AV2* input source on the TV

using the

INPUT button on the remote control.

ꔛ

Refer to the DVD player's manual for operating

instructions.

RGB IN (PC)

AUDIO IN

RGB/DVI

(DVI)

OPTICAL

DIGITAL

AUDIO OUT

/DVI IN

COMPONENT IN

RS-232C IN

(

CONTROL&SERVICE)

1 2

VIDEO

AUDIO

L R

AV IN

VIDEO

AUDIO

L(MONO)

L R

VIDEO

AUDIO

ANTENNA

DC-IN

RGB IN (PC)

AUDIO IN

RGB/DVI

OPTICAL

DIGITAL

AUDIO OUT

COMPONENT IN

AV IN

RS-232C IN

(

CONTROL&SERVICE)

VIDEO

AUDIO

L(MONO)

VIDEO

AUDIO

L R

(DVI)

/DVI IN

1 2

HDMI OUTPUT

HDMI Connection

1. How to connect

Connect the HDMI output of the DVD to the

HDMI/DVI IN 1, 2, 3*, or 4** jack on the TV.

No separate audio connection is necessary.

HDMI supports both audio and video.

2. How to use

ꔛ

Select the HDMI, HDMI1, HDMI2 HDMI3*, or HDMI4**

input source on the TV using the INPUT

button on

the remote control.

ꔛ

Refer to the DVD player's

manual for operating instructions.

NOTE

► If an HDMI cable doesn’t support High Speed HDMI,

it can cause flickers or no screen display. In this case

use the latest cables that support High Speed HDMI.

► HDMI Audio Supported Format: Dolby Digital (32 KHz, 44.1

KHz, 48 KHz), Linear PCM (32 KHz, 44.1 KHz, 48 KHz)

* AV2: For 42/50PJ250, 42/50PJ350, 32LD350,

32/42LD420, 32/42LD420C, 32/37/42/47LD460,

37/42LD461C, 32/37/42/47LD465, 32/42LE4300,

32/37/42/47/55LE5300, 32/42/47/55LE4600,

32/42LD460H

* HDMI3: For 26LE5300, 22/26LE6500,

32/42/47/55LE4600, 32/42LE4300

** HDMI4: For 32/37/42/47/55LE5300

EXTERNAL EQUIPMENT SETUP

VCR SETUP

Antenna Connection

C IN

ERVICE)

UDIO

DIO

ANTENNA

CABLE IN

L R

S-VIDEO VIDEO

AUDIO

OUTPUT

SWITCH

ANT IN

ANT OUT

Wall Jack

Antenna

1. How to connect

Connect the RF antenna out socket

of the VCR to the ANTENNA/CABLE

IN socket on the TV.

Connect the antenna cable to the RF

antenna in socket of the VCR.

2. How to use

ꔛ

Set VCR output switch to 3 or 4 and

then tune TV to the same channel num-

ber.

ꔛ

Insert a video tape into the VCR and

press PLAY on the VCR (Refer to the

VCR owner’s manual).

Composite (RCA) Connection

RGB IN (PC)

AUDIO IN

RGB/DVI

(DVI)

OPTICAL

DIGITAL

AUDIO OUT

COMPONENT IN

RS-232C IN

(

CONTROL&SERVICE)

1 2

VIDEO

AUDIO

L R

AV IN

VIDEO

AUDIO

L(MONO)

S-VIDEO

OUTPUT

SWITCH

ANT IN

ANT OUT

L R

VIDEO

AUDIO

ANTENNA

CAB

1. How to connect

Connect the AUDIO/VIDEO jacks between TV

and VCR. Match the jack colors (Video = yellow,

Audio Left = white, and Audio Right = red)

2. How to use

ꔛ

Insert a video tape into the VCR and press PLAY

on the VCR.

(

Refer to the VCR owner’s manual.

)

ꔛ

Select the AV, AV1 or AV2* input source on the TV

using the

INPUT button on the remote control.

NOTE

► If you have a mono VCR, connect the audio cable

from the VCR to the AUDIO L/MONO jack of the TV.

* AV2: For 42/50PJ250, 42/50PJ350, 32LD350,

32/42LD420, 32/42LD420C, 32/37/42/47LD460,

37/42LD461C, 32/37/42/47LD465, 32/42LE4300,

32/37/42/47/55LE5300, 32/42/47/55LE4600,

32/42LD460H

EXTERNAL EQUIPMENT SETUP

OTHER A/V SOURCE SETUP

1. How to connect

Connect the AUDIO/VIDEO jacks

between TV and external equipment.

Match the jack colors

(

Video = yellow, Audio Left = white, and

Audio Right = red

)

2. How to use

ꔛ

Select the AV, AV1 or AV2* input source

on the TV using the

INPUT button on

the remote control.

ꔛ

Operate the corresponding external

equipment.

C-IN

RGB IN (PC)

AUDIO IN

RGB/DVI

(DVI)

OPTICAL

DIGITAL

AUDIO OUT

/DVI IN

COMPONENT IN

RS-232C IN

(

CONTROL&SERVICE)

1 2

VIDEO

AUDIO

L R

AV IN

VIDEO

AUDIO

L(MONO)

L R

VIDEO

AUDIO

Camcorder

Video Game Set

* AV2: For 42/50PJ250, 42/50PJ350, 32LD350,

32/42LD420, 32/42LD420C, 32/37/42/47LD460,

37/42LD461C, 32/37/42/47LD465, 32/42LE4300,

32/37/42/47/55LE5300, 32/42/47/55LE4600,

32/42LD460H

EXTERNAL EQUIPMENT SETUP

USB CONNECTION (Except 32LD350, 42/50PJ230)

HEADPHONE SETUP

(For LED LCD TV/LCD TV)

1. How to connect

Connect the USB device to the USB

IN jack on the side of TV.

2. How to use

ꔛ

After connecting the USB IN jack, you

use the USB function. (

►p.90)

You can listen to the sound through the headphone.

1. How to connect

Plug the headphone into the head-

phone socket.

To adjust the headphone volume,

press the VOL +/- button. If you

press the MUTE button, the sound

from the headphone is switched off.

NOTE

►

AUDIO menu options are disabled when connecting a head-

phone.

►

When changing AV MODE with a headphone connected, the

change is applied to video but not to audio.

►

Optical Digital Audio Out is not available when connecting a

headphone.

H/P

USB IN

IN 3

H/P

Memory Key

EXTERNAL EQUIPMENT SETUP

RGB IN (PC)

AUDIO IN

RGB/DVI

(DVI)

/DVI I

COMPONENT IN

AV IN

RS-232C IN

(

CONTROL&SERVICE)

1 2

VIDEO

AUDIO

L(MONO)

VIDEO

AUDIO

L R

OPTICAL

DIGITAL

AUDIO OUT

AUDIO OUT CONNECTION

Send the TV’s audio to external audio equipment via the Audio Output port.

If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL

AUDIO OUT terminal on the back of TV to a Home Theater (or amp).

NOTE

► When connecting with external audio equipment, such

as amplifiers or speakers, you can turn the TV speakers

off in the menu. (

►p.132)

CAUTION

► Do not look into the optical output port. Looking at

the laser beam may damage your vision.

► Audio with ACP (Audio Copy Protection) function may

block digital audio output.

1. How to connect

Connect one end of the optical cable to the

TV port of OPTICAL DIGITAL AUDIO OUT.

Connect the other end of the optical cable to

the digital audio input on the audio equip-

ment.

Set the “TV Speaker option - Off” in the

AUDIO menu. (

►p.132). See the external audio

equipment instruction manual for operation.

EXTERNAL EQUIPMENT SETUP

EXTERNAL EQUIPMENT WIRELESS CONNECTION

(32/37/42/47/55LE5300, 32/42LE4300 OPTIONAL EXTRA)

LG TVs with a Wireless Control port support the LG Wireless Media Box, which is sold separately.

When you connect the wireless ready dongle (included with the media box) to the TV, external devices

can be connected to the LG Wireless Media Box and video and audio will be sent to the TV wirelessly.

RGB IN (PC)

LAN

(RGB/DVI)

VIDEO

AUDIO

L(MONO)

VIDEO

AUDIO

COMPONENT INAV IN 1

AUDIO IN

AUDIO OUT

WIRELESS

CONTROL

OUT

WIRELESS

CONTROL

/DVI IN

YPB PR

L R

OPTICAL DIGITAL

RS-232C IN

(

SERVICE ONLY)

ꔡ

1. How to connect

Connect the WIRELESS CONTROL jack of the Wireless Dongle to the WIRELESS

CONTROL jack on the TV.

Connect HDMI OUT jack of the Wireless Dongle to the HDMI IN jack on the TV.

2. How to use

ꔛ

Select the desired input source on the TV using the INPUT button on the remote control.

ꔛ

Refer to the Wireless Media Box manual for operating instructions.

EXTERNAL EQUIPMENT SETUP

DC-IN

()

OPTICAL

DIGITAL

AUDIO OUT

COMPONENT IN

AV IN

(

CONTROL&SERVI

VIDEO

AUDIO

L(MONO)

VIDEO

AUDIO

RGB IN (PC)

AUDIO IN

RGB/DVI

RGB OUTPUT

AUDIO

PC SETUP (Except 42/50PJ230)

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's set-

tings.

1. How to connect

Connect the VGA output of the PC to the

RGB IN

(

)

jack on the TV.

Connect PC audio output to the AUDIO IN

(

RGB/DVI

)

jack on the TV.

2. How to use

ꔛ

Turn on the PC and the TV.

ꔛ

Select the RGB-PC input source on the TV using

the

INPUT button on the remote control.

VGA (D-Sub 15 Pin) Connection

EXTERNAL EQUIPMENT SETUP

DVI to HDMI Connection

1. How to connect

Connect the DVI output of the PC to the HDMI/

DVI IN or 1 jack on the TV.

Connect the PC audio output to the AUDIO IN

(RGB/DVI) jack on the TV.

2. How to use

ꔛ

Turn on the PC and the TV.

ꔛ

Select the HDMI or HDMI1 input source on the TV

using the

INPUT

button on the remote control.

DC-IN

RGB IN (PC)

AUDIO IN

RGB/DVI

OPTICAL

DIGITAL

AUDIO OUT

COMPONENT IN

AV IN

RS-232C IN

(

CONTROL&SERVICE)

VIDEO

AUDIO

L(MONO)

VIDEO

AUDIO

L R

(DVI)

/DVI IN

1 2

DVI OUTPUT

AUDIO

EXTERNAL EQUIPMENT SETUP

Supported Display Specifications (RGB-PC, HDMI-PC)

NOTE

►LED LCD TV/LCD TV: To get the best picture quality, adjust the PC graphics card to 1360x768

(32LD350, 22/26/32LE5300) or 1920x1080 (Other models).

►Plasma TV: To get the best picture quality, adjust the PC graphics card to 1360x768.

►Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use.

►In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or bright-

ness. If noise is present, change the PC output to another resolution, change the refresh rate to

another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.

►Avoid keeping a fixed image on the screen for a long period of time. The fixed image may become

permanently imprinted on the screen.

►The synchronization input form for Horizontal and Vertical frequencies is separate.

►Depending on the graphics card, some resolution settings may not allow the image to be posi-

tioned on the screen properly.

►When selecting HDMI-PC, set the “Input Label - PC” in the OPTION menu.

Resolution

Horizontal

Frequency

(

KHz

)

Vertical

Frequency

(

)

640x350 31.468 70.09

720x400 31.469 70.08

640x480 31.469 59.94

800x600 37.879 60.31

1024x768 48.363 60.00

1280x768 47.776 59.87

1360x768

47.712 60.015

1280x1024

63.981 60.02

1600x1200

75.00 60.00

1920x1080

67.50 60.00

Except 32LD350, 22/26/32LE5300,

42/50PJ250, 42/50PJ350

EXTERNAL EQUIPMENT SETUP

Screen Setup for PC mode

You can choose the resolution in RGB-PC mode.

The Position, Phase, and Size can also be adjusted.

You can choose this option only when the PC resolution is set to 1024X768, 1280X768 or 1360X768.

Selecting Resolution

Select PICTURE.

ENTER

Select Screen (RGB-PC).

ENTER

Select Resolution.

ENTER

Select the desired resolution.

ENTER

ꔑ 1024 x 768

□ 1280 x 768

□ 1360 x 768

Auto Config.

Resolution

Position

Size

Phase

Reset

SCREEN

ꔂ Move ꕉ Prev.

PICTURE

ꔂ Move ꔉ Enter

•

Brig

htne

ss 5

• Sharpness 70

• Color 60

• Tint 0

• Color Temp. 0

• Advanced Control

• Picture Reset

• Screen (RGB-PC)

ꔉ

ꔠ

EXTERNAL EQUIPMENT SETUP

Automatically adjusts picture position and minimizes image instability. After adjustment, if the image

is still not correct, try using the manual settings or a different resolution or refresh rate on the PC.

Auto Configure

Select PICTURE.

ENTER

Select Screen (RGB-PC).

ENTER

Select Auto Config..

ENTER

Select Yes.

ENTER

ꔛ

If the position of the image is still not

correct, try Auto adjustment again.

ꔛ

If picture needs to be adjusted again

after Auto adjustment in RGB-PC,

you can adjust the Position, Size or

Phase.

Auto Config.

Resolution

Position

Size

Phase

Reset

Auto Config.

Yes No

SCREEN

ꔂ Move ꕉ Prev.

PICTURE

ꔂ Move ꔉ Enter

•

Brig

htne

ss 5

• Sharpness 70

• Color 60

• Tint 0

• Color Temp. 0

• Advanced Control

• Picture Reset

• Screen (RGB-PC)

ꔉ

ꔠ

EXTERNAL EQUIPMENT SETUP

If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust

the picture phase manually.

This feature operates only in RGB-PC mode.

Adjustment for screen Position, Size, and Phase

Select PICTURE.

ENTER

Select Screen (RGB-PC).

ENTER

Select Position, Size, or Phase.

ENTER

Make appropriate adjustments.

ENTER

ꔛ

Position: This function is to adjust

picture to left/right and up/down as

you prefer.

ꔛ

Size: This function is to minimize any

vertical bars or stripes visible on the

screen background. And the horizon-

tal screen size will also change.

ꔛ

Phase: This function allows you to

remove any horizontal noise and

clear or sharpen the image of char-

acters.

Auto Config.

Resolution

Position

Size

Phase

Reset

▲

◀▶

▼

SCREEN

ꔂ Move ꕉ Prev.

PICTURE

ꔂ Move ꔉ Enter

•

Brig

ht e

htne

ss 5

• Sharpness 70

• Color 60

• Tint 0

• Color Temp. 0

• Advanced Control

• Picture Reset

• Screen (RGB-PC)

ꔉ

ꔠ

EXTERNAL EQUIPMENT SETUP

Returns Position, Size, and Phase to the default initial settings.

This feature operates only in RGB-PC mode.

Screen Reset (Reset to original initial values)

Select PICTURE.

ENTER

Select Screen (RGB-PC).

ENTER

Select Reset.

ENTER

Select Yes.

ENTER

Auto Config.

Position

Resolution

Size

Phase

Reset

To Set

Yes No

SCREEN

ꔂ Move ꕉ Prev.

PICTURE

ꔂ Move ꔉ Enter

•

Brig

htne

ss 5

• Sharpness 70

• Color 60

• Tint 0

• Color Temp. 0

• Advanced Control

• Picture Reset

• Screen (RGB-PC)

ꔉ

ꔠ

WATCHING TV / CHANNEL CONTROL

REMOTE CONTROL FUNCTIONS

When using the remote control, aim it at the remote control sensor on the TV.

WATCHING TV / CHANNEL CONTROL

POWER Turns the TV on from standby or off

to standby.

ENERGY SAVING

Adjusts the Energy Saving setting.

►p.116

AV MODE Toggles through preset Video and

Audio modes.

►p.87

INPUT Rotates through inputs.

Also switches the TV on from stand-

by.

►p.82

TV Returns to the last TV channel.

NUMBER button

- (DASH) Used to enter a program number for

multiple program channels such as

5-1, 5-2, etc.

LIST Displays the channel table. ►p.74

Q.VIEW Tunes to the last channel viewed.

ENERGY

CHVOL

456

SAVING

AV MOD E

INPUT

FAV

RATIO

MUTE

MARK

Q.VIEW

LIST

FREEZE

ENTER

GUIDE

Q.MENU

INFO

BACK

EXIT

ENERGY

CHVOL

12 3

456

SAVING

AV MOD E

INPUT

FAV

PORTAL

MUTE

MARK

Q.VIEW

LIST

FREEZE

ENTER

GUIDE

Q.MENU

INFO

BACK

EXIT

RATIO

VOLUME UP/

DOWN

Adjusts the volume.

FAV Set up desired favorite channels list

►p.73

MARK Select the input to apply the Picture

Wizard settings.

►p.115

Use to mark or unmark a photo/

music/movie.

►p.95, 100, 106

RATIO Changes the aspect ratio. ►p.112

PORTAL Displays and removes hotel interactive

menu.

MUTE Switches the sound on or off. ►p.60

CHANNEL

UP/DOWN

Changes the channel.

PAGE

UP/DOWN

Moves from one full set of screen

information to the next one.

WATCHING TV / CHANNEL CONTROL

MENU Displays the main menu or clears all

on-screen displays and return to TV

viewing.

GUIDE Displays the program event accord-

ing to time scheduler.

►p.79

Q.MENU Opens the list of Quick Menu

options.

►p.65

THUMBSTICK

(Up/Down/

Left

Right/ENTER)

Navigates the on-screen menus and

adjusts the system settings to your

preference.

BACK Allows the user to move return one

step in an interactive application or

other user interaction function.

INFO Displays the information of watching

program.

►p.78

EXIT Clears all on-screen displays and

return to TV viewing.

COLOR

BUTTON

Access special functions in some

menus.

USB,

SIMPLINK

Control buttons

• Controls MY MEDIA menu

(Photo List, Music List, Movie List)

• Controls the SIMPLINK compati-

ble devices.

FREEZE

(For Plasma TV)

Freeze the current frame while view-

ing the TV, AV, Component, RGB-

PC. or HDMI input source.

SIMPLINK See a list of AV devices connected

to TV.

When you toggle this button, the

SIMPLINK menu appears at the

screen.

►p.88

ꔛ

Open the battery compartment cover on the back side

and install the batteries matching correct polarity.

ꔛ

Install two 1.5V AAA batteries. Don’t mix old or used

batteries with new ones.

ꔛ

Close cover.

Installing Batteries

ENERGY

CHVOL

456

SAVING

AV MOD E

INPUT

FAV

RATIO

MUTE

MARK

Q.VIEW

LIST

FREEZE

ENTER

GUIDE

Q.MENU

INFO

BACK

EXIT

ENERGY

CHVOL

12 3

456

SAVING

AV MOD E

INPUT

FAV

PORTAL

MUTE

MARK

Q.VIEW

LIST

FREEZE

ENTER

GUIDE

Q.MENU

INFO

BACK

EXIT

RATIO

RATIO Changes the aspect ratio. ►p.112

WATCHING TV / CHANNEL CONTROL

TURNING ON THE TV

CHANNEL SELECTION

VOLUME ADJUSTMENT

Adjust the volume to suit your personal preference.

First, connect power cord correctly.

At this moment, the TV switches to standby mode.

ꔛ

In standby mode to turn TV on, press the

/ I, INPUT, CH (ꕌ or ꕍ) button on the TV or press

the

POWER, INPUT, CH (ꕌ or ꕍ), Number (0~9) button on the remote control.

Select the viewing source by using the INPUT button on the remote control.

When finished using the TV, press the POWER button on the remote control. The TV reverts

to standby mode.

NOTE

► If you intend to be away on vacation, disconnect the power plug from the wall power outlet.

► If you do not complete the Initial setting, it will appear whenever the TV is switched on until the

Initial setting procedure is completed.

Press the CH (ꕌor ꕍ) or NUMBER buttons to select a channel number.

Press the VOL

(+ or -) button to adjust the volume.

If you want to switch the sound off, press the MUTE button.

You can cancel the Mute function by pressing the MUTE or VOL

(+ or -)

button.

WATCHING TV / CHANNEL CONTROL

Step1. Selecting Language

INITIAL SETTING

This Function guides the user to easily set the essential items for viewing the TV for the first time

when purchasing the TV. It will be displayed on the screen when turning the TV on for the first time. It

can also be activated from the user menus.

ꔛ

Default selection is “Home Use”. We recommend setting the TV to “Home Use” mode for the best

picture in your home environment.

ꔛ

“Store Demo” Mode is only intended for use in retail environments. Customers can adjust the

“Picture menu - Picture mode” manually while inspecting the TV, but the TV will automatically

return to preset in-store mode after 5 minutes.

ꔛ

“Store Demo” Mode is an optimal setting for displaying at stores. “Store Demo” mode initializes

the TV to set the image quality.

Select Menu Language.

ENTER

WELCOME!

Thank you for choosing LG

ꔉ Next

Step 1. Language

Português

English

Español

Step2. Mode setting

Select Home Use.

ENTER

Home Use Store Demo

• Demo Mode Off

Step 2. Mode Setting

Selecting the environment.

Choose the setting mode you want.

Select [Home Use] to use this TV at home.

To use this TV at store, select [Store Demo].

ꕉ Previous ꔉ Next

WATCHING TV / CHANNEL CONTROL

Step4. Time Zone

Step5. Auto Tuning

Select Time Zone option.

Select Daylight Saving

option.

ENTER

Check your antenna connection and

start Auto Tuning.

Step 4. Time Zone

ꕉ Previous ꔉ Next

Time Zone ◀ Brasilia ▶

Daylight Saving Auto

Step 5. Auto Tuning

ꕉ Previous ꔉ Next

Before starting,

be sure that the

TV antenna is connected.

Step3. Power Indicator (For LED LCD TV)

Select On or Off.

ENTER

Step 3. Power Indicator

ꕉ Previous ꔉ Next

Standby Light ◀ Off ▶

ꔛ

This function is disable in “Step2. Mode

Setting - Store Demo”.

WATCHING TV / CHANNEL CONTROL

ON-SCREEN MENUS SELECTION

Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.

Display each menu.

ENTER

Select a menu item.

ENTER

Accept the current selection.

EXIT

Return to TV viewing.

CHANNEL

OPTION

PICTURE

AUDIO

TIME

LOCK

PICTURE

ꔂ Move ꔉ Enter

• Aspect Ratio : 16:9

• Picture Wizard

• ꕊ Energy Saving : Off

• Picture Mode : Standard

• Backlight 70

• Contrast 100

• Brightness 50

•

Shar

pnes

s70

s 70

s70

TIME

ꔂ Move ꔉ Enter

• Clock

• Off Time : Off

• On TIme : Off

• Sleep Timer : Off

LOCK

ꔂ Move ꔉ Enter

• Set Password

• Lock System : On

• Block Channel

• Rating

• Input Block

• Key Lock : Off

OPTION

ꔂ Move ꔉ Enter

• Language

• Caption : Off

• Power Indicator

• Initial Setting

• Set ID : 1

• Mode Setting : Home Use

• IR Blaster : Off

AUDIO

ꔂ Move ꔉ Enter

• Auto Volume : Off

• Clear Voice II : Off ꕅ3

• Balance 0

• Sound Mode : Standard

•

Infinite Sound: Off

• Treble 50

• Bass 50

•

Rese

ese

CHANNEL

ꔂ Move ꔉ Enter

• Auto Tuning

• Manual Tuning

• Channel Edit

• Scan Option

• System Color

NOTE

► ISM Method: For Plasma TV.

► Backlight, TruMotion, Power Indicator:

For LED LCD TV/LCD TV.

ꔛ

For further information, refer to the

optional “Wireless Media Box”

manual for operating instructions.

WATCHING TV / CHANNEL CONTROL

INPUT

Input List

ꔂ Move ꔉ Enter

TV USB1 USB2 AV Component1 Component2

RGB-PC HDMI1 HDMI2 HDMI3 HDMI4

ꔅ Input Label ꕉ Exit

MY MEDIA

Except 42/50PJ230, 32LD350

i.e)

Movie List

MY MEDIA

Photo List Music List

Extra Contents

For 32/42LD460H

WATCHING TV / CHANNEL CONTROL

ꕊ

16:9 ꔉ16:9 ꔉ

◀ Aspect Ratio ▶◀ Aspect Ratio ▶

ꔣ Aspect Ratio: Selects your desired picture format.

ꕇ Picture Mode: Selects the desired preset picture setting.

ꕈ Sound Mode: Selects the desired preset sound setting.

ꔴ Multi Audio: Changes the audio language (Digital signal).

ꔴ SAP: Selects MTS sound (Analog signal).

ꔤ Sleep Timer: Select the amount of time before your TV turns off automatically.

ꔳ Del/Add: Select channel you want to add or delete.

ꕄ Caption: Select on or off.

ꕊ Energy Saving: Select the energy saving level to reduce the TV’s power consumption.

ꔢ USB Device: Select “Eject” in order to eject a USB device.

QUICK MENU

Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.

Q.Menu (Quick Menu) is a menu of features which users might use frequently.

Q.MENU

Display each menu.

ENTER

Make appropriate adjustments.

EXIT

Return to TV viewing.

ꕉ Exitꕉ Exit

42/50PJ230, 32LD350 Other models

WATCHING TV / CHANNEL CONTROL

CUSTOMER SUPPORT

Software Update

ꔑ Software Update

□ Picture Test

□ Sound Test

□ Product/Service Info.

You can update the TV with the latest software to enhance the product operation and/or add new fea-

tures.

You can update the software by connecting the TV directly to the software update server.

The Software Update function may not work properly depending on your internet environment. In this

case, you can obtain the latest software from the authorized LG Electronics Service Center then update

your TV.

Select Customer Support.

ENTER

Select Software Update.

ENTER

Select On. The user confirm mes-

sage box will be displayed to

notify that new software is found.

BACK

Return to the previous menu.

EXIT

Return to TV viewing.

RED

ꔛ

If you cancel the update, select

Software - Off.

ꔛ

This TV cannot be updated to previ-

ous software version.

ꔛ

After software update, you can con-

firm the update software version at

software Update menu.

ꔛ

The TV function may be improved or

changed by software update.

ꔛ

When an update is completed, some

CHANNEL, PICTURE, and AUDIO

menu settings may need to resetting.

Occasionally, a transmission of updat-

ed digital software information will

result in the following menu on the TV

screen.

Simple Update : for current update

stream

Schedule Update : for scheduled

update stream

A window as display below

appears when download com-

pletes.

TV is restarted when "Yes"

button is pressed.

When the Software Update menu is

"Off", the message to change it to "On"

appears.

Download starts when "Yes" is

selected. At this time, progress-

ing pop-up window does not

display.

Download progress status can

be checked from Software

Update menu.

Yes

Software update is available.

Would you like to download now?

Yes

A new software update is available at

00/00/0 00:00.

Do you want to update the software when

available?

Yes

New software version is ready. If you want to

install now, TV will be turned off and restart.

Continue?

Software Update

Software downloading progress.

Ver. 00.00.01 ► Ver.00.00.00

◄ On ►

Software Update On

• Current Version

01.00.18

When setting “Software Update”

WATCHING TV / CHANNEL CONTROL

Picture Test/Sound Test

This function is a customer support function that can execute picture and sound tests.

□ Software Update

□ Picture Test

ꔑ Sound Test

□ Product/Service Info.

Yes

Do you have a sound problem in this

screen?

Select Customer Support.

ENTER

Select Picture Test or Sound Test.

ENTER

Select Yes.

BACK

Return to the previous menu.

EXIT

Return to TV viewing.

□ Software Update

ꔑ Picture Test

□ Sound Test

□ Product/Service Info.

Yes

Do you have a problem in this test

screen?

RED

WATCHING TV / CHANNEL CONTROL

Product/Service Info.

□ Software Update

□ Picture Test

□ Sound Test

ꔑ Product/Service Info.

This function shows support and product information.

Select Customer Support.

ENTER

Select Product/Service Info..

You can check the various

product/Service infomation

based on your model.

BACK

Return to the previous menu.

EXIT

Return to TV viewing.

RED

WATCHING TV / CHANNEL CONTROL

SIMPLE MANUAL

You can easily and effectively access the TV information by viewing a simple manual on the TV.

During the Simple Manual operation, audio will be muted.

Select Simple Manual.

Select the part of the manual you would like to see.

Go to the Index page.

Play the Simple Manual automatically or manually.

EXIT

Return to TV viewing.

RED

BLUE

GREEN

WATCHING TV / CHANNEL CONTROL

CHANNEL SETUP

Auto Scan (Auto Tuning)

Automatically finds all channels available through antenna or cable inputs, and stores them in memory

on the channel list.

Run this function if you change your residence or move the TV.

Auto Tuning memorizes only the channels available at the time.

Select CHANNEL.

ENTER

Select Auto Tuning.

ENTER

Select Start.

ENTER

Run Auto tuning.

BACK

Return to the previous menu.

EXIT

Return to TV viewing.

ꔛ

The TV will ask for a password if

parental control has been activated

(LOCK Menu). Use the password you

set up in the LOCK Menu to allow a

channel search.

ꔛ

The maximum number of channels

the TV can store is 500.

ꔛ

Found channels are grouped in the

order of DTV, TV, and Cable TV.

CHANNEL

ꔂ Move ꔉ Enter

CHANNEL

ꔂ Move ꔉ Enter

ꔡ

ꔉ

• Auto Tuning

• Manual Tuning

• Channel Edit

• Scan Option

• System Color

• Auto Tuning

• Manual Tuning

• Channel Edit

• Scan Option

• System Color

Check your antenna connection.

The previous channel information

will be updated during Auto Tuning.

Antenna

Cable

Start

WATCHING TV / CHANNEL CONTROL

Add/Delete Channel (Manual Tuning)

When selecting DTV input signal in the Manual Tuning, you can view the on-screen signal strength

monitor to see the quality of the signal being received.

Select CHANNEL.

ENTER

Select Manual Tuning.

ENTER

Select DTV, TV, or Cable TV.

Select channel you want to

add or delete.

ENTER

Select Add or Delete.

BACK

Return to the previous menu.

EXIT

Return to TV viewing.

ꔛ

The TV will ask for a password if

parental control has been activated

(LOCK Menu). Use the password you

set up in the LOCK Menu to allow a

channel search.

ꔛ

The maximum number of channels

the TV can store is 500.

CHANNEL

ꔂ Move ꔉ Enter

• Auto Tuning

• Manual Tuning

• Channel Edit

• Scan Option

• System Color

CHANNEL

ꔂ Move ꔉ Enter

ꔀ

ꔉ

• Auto Tuning

• Manual Tuning

• Channel Edit

• Scan Option

• System Color

Channel

Select channel type and RF-channel

number.

◀

DTV

▶

Delete

DTV 5-1

• Signal Strength

• Signal Quality

88%

WATCHING TV / CHANNEL CONTROL

Channel Editing

ꔛ

Keep pressing the ꕌ button and use

the

buttons to move between

DTV, TV, and Cable TV.

Select CHANNEL.

ENTER

Select Channel Edit.

ENTER

Select a channel.

Add or delete a channel.

Block or unblock the channel.

You can block/unblock channels even if

you select “Lock system-Off” in the LOCK

menu.

ENTER

Switch to the chosen channel number.

Move the pages when the channel list is

too long.

BACK

Return to the previous menu.

EXIT

Return to TV viewing.

BLUE

YELLOW

CHANNEL

ꔂ Move ꔉ Enter

ꔀ

ꔉ

• Auto Tuning

• Manual Tuning

• Channel Edit

• Scan Option

• System Color

The channels in the Channel Edit List are displayed in black and the channels deleted from the Channel

Edit List are displayed in blue.

When a channel number is deleted, it means that you will be unable to select it using

CH∧∨button

during TV viewing.

If you wish to select the deleted channel, directly enter the channel number with the NUMBER buttons

or select it in the Channel Edit menu.

5-13-1 7-1

ꔉ CH.Change

DTV TV Cable TV

ꔂ Navigation ꘃ Page Change

ꔅ Block/Unblock ꔅ Add/Delete

ꘂ Favorite Ch.

Channel Edit

Page 1/1

꘩ Favorite Ch. Group ꕉ Previous

Favorite Group:

WATCHING TV / CHANNEL CONTROL

FAVORITE CHANNEL SETUP

Favorite Channels are a convenient feature that lets you quickly select channels of your choice without

waiting for the TV to select all the in-between channels.

FAV

MARK

Display the Favorite channel list.

Select a channel.

ENTER

Switch to the chosen channel number.

Turn the pages.

BACK

Return to TV viewing.

Selecting a channel in the favorite

channel list

Paging through a favorite channel

list

Displaying the favorite channel list

ꔛ

You can also setup Favorite List in the

CHANNEL menu - Channel Edit.

123

789

Select your desired channel.

FAV

MARK

Select your desired favorite

channel group from A to D.

in favorite channel list.

Go to the “CHANNEL menu - Channel

Edit”.

EXIT

Return to TV viewing.

YELLOW

BLUE

FAVORITE CHANNEL LIST

ꔊꔋFavorite Ch. Group

Favorite List

ꕉ Exit

◀

Group

▶

◀

Group

▶

DT V

3-1

DT V

4-1

DT V

3-1

DT V

4-1

ꔅ Ch.Reg.

ꔅ Ch.Edit

ꔡ

ꔉ

ꔡ

ꔉ

WATCHING TV / CHANNEL CONTROL

CHANNEL LIST

You can check which channels are stored in the memory by displaying the channel list.

Channel List

ꕉ Exit

DT V

3-1 ꔒ

DT V

4-1

ꔅ Ch.Edit

Select a channel.

ENTER

Switch to the chosen channel number.

LIST

Display the Channel List.

Tune to the “CHANNEL menu - Channel

Edit”.

Turn the pages.

EXIT

Return to TV viewing.

Selecting a channel in the channel list

Paging through a channel list

Displaying Channel List

BLUE

This padlock is displayed

when the channel is locked

with parental control.

ꔡ

ꔉ

WATCHING TV / CHANNEL CONTROL

SCAN OPTION

CHANNEL

ꔂ Move ꔉ Enter

• Auto Tuning

• Manual Tuning

• Channel Edit

• Scan Option

• System Color

*This feature is not available for all models.

Whether to search all channels or the first channel of virtual channels is switched with

CH∧∨button

when one or more virtual channels exist at one physical channel.

Select CHANNEL.

ENTER

Select Scan Option.

ENTER

Select Primary Channel or

All Channels.

BACK

Return to the previous menu.

EXIT

Return to TV viewing.

ꔛ

Primary Channel: Only scan the first

channel of virtual channels.

ꔛ

All Channels: Scan full channel.

ꔀ

ꔉ

• Auto Tuning

• Manual Tuning

• Channel Edit

• Scan Option

• System Color

ꔑ Primary Channel

□ All Channels

ꔡ

ꔉ

WATCHING TV / CHANNEL CONTROL

SYSTEM COLOR

CHANNEL

ꔂ Move ꔉ Enter

• Auto Tuning

• Manual Tuning

• Channel Edit

• Scan Option

• System Color

This function set color suited the each signal.

This feature is disable in digital channel.

Select CHANNEL.

ENTER

Select System Color.

ENTER

Select Multi, PAL-M, PAL-N, or NTSC.

BACK

Return to the previous menu.

EXIT

Return to TV viewing.

ꔉ

ꔠ

• Auto Tuning

• Manual Tuning

• Channel Edit

• Scan Option

• System Color

□ Multi

□ PAL-M

□ PAL-N

ꔑ

NTSC

ꔉ

ꔠ

WATCHING TV / CHANNEL CONTROL

Sun, Feb 21, 2010 10: 40 AM

ꔥ Multilingual ꔨ ꔯ Caption ꔷ 1080i ꔒ 14 ꔇ

10:10 AM 11:40 AM

Brief Info Title Test...

Next - 11:40 AM News

8-1

GLOBO-HD

ꔖ DTV

ꔱ ꔫ

6 3 11 4 5 2

ꔥ

Multilingual : The program contains two or more audio servic-

es. Use the Q.MENU menu to select wanted Audio.

ꔯ

Caption : The program contains one or more caption services.

Use the Q.MENU menu to select wanted Closed caption.

ꔨ

Dolby Digital: The program contains a Dolby Digital audio

signal in TV and HDMI input source.

ꔶ

The original aspect ratio of the video is 4:3

ꔷ

The original aspect ratio of the video is 16:9 (wide)

480i

480p

720p

1080i

The video resolution is 720x480i

The video resolution is 720x480p

The video resolution is 1280x720p

The video resolution is 1920x1080i

ꔇ

Description

ꔒ

Refer to the LOCK menu.

ENTER

Show the Brief Info on the screen.

ENTER

Return to TV viewing.

Program title

Day, Month, Year,

Present time

Program start time

Program progress

bar

Program finish

time

Banner information

CHANNEL BRIEF INFORMATION

Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.

WATCHING TV / CHANNEL CONTROL

GUIDE

INFO

Shows current channel information

Shows next channel information.

Show other channel’s program information

Channel Program Reservation

Yes

Do you want to set a remind for the

selected program?

Bob The Builder Special

ꔖ DTV 1 ABC TV

Mar. 9, 2010 5:30 PM ~ 8:00 PM

GUIDE

INFO

Show the current channel program

Information on the screen.

Select a next channel program information

ENTER

Select Yes or No.

EXIT

Return to TV viewing.

ꔥ Multilingual ꔨ ꔯ Caption ꔷ 1080i ꔒ 14 TV-PG D L S V

Brief Info Title Test...

ꔖ DTV 8-1 CNN

ꔀ Ch. Change ▶ Next ꔉ Watch

10:10 AM 11:40 AM

No information

Sarah Bradley, Steve Gray and Brendon Pongia present the latest in fashion, the arts, entertainment, lifestyle and cooking,

with regular and special guests.

Sarah Bradley, Steve Gray and Brendon Pongia present the latest in fashion, the arts, entertainment, lifestyle and cooking,

ꔡ

ꔅ Up

ꔅ Down

WATCHING TV / CHANNEL CONTROL

NOW/NEXT Guide Mode

You can view a program being broadcasted and one scheduled to follow.

RED

Change EPG mode.

YELLOW

Enter Manual Timer mode.

BLUE

Enter Schedule List mode.

ENTER

When ‘Now’ is selected, it is moved to

selected program and EPG disappears

When ‘Next’ is selected, a reservation

pop-up window appears.

Select NOW or NEXT Programme.

Select the Broadcast Programme.

Page Up/Down.

GUIDE

Display the Program Guide.

Select the desired program.

Program Guide

ALL

May. 7, 2010 10:07 PM

ꘂ Favorite

ꔅ Mode

ꔅ Manual Timer ꔅ Schedule List

꘍ Information ꔉ Watch/Schedule ꕉ Exit

5-1 Globo HD

5-2 CCTV-1

7-1 CCTV-2

9-2 BTV-1

9-3 CETV-1

DTV

Racing News

ꔖ DTV 5-1 Globo HD

Antigues Roadshow

TV2: FARMEN

No Information

The Drum

Fashion Essentials

No Information

NOW NEXT

EPG (ELECTRONIC PROGRAM GUIDE)

(IN DIGITAL MODE)

This system has an Electronic Program Guide (EPG) to help your navigation through all the possible

viewing options.

The EPG supplies information such as program listings, start and end times for all available services.

In addition, detailed information about the program is often available in the EPG (the availability and

amount of these program details will vary, depending on the particular broadcaster).

This function can be used only when the EPG information is broadcast by broadcasting companies.

The EPG displays the program details for next 8 days.

Program Guide

ALL

Fri, May. 7

May. 7, 2010 10:07 PM

10:00 PM

11:00 PM

ꘂ Favorite

ꔅ Mode ꔅ Date

ꔅ Manual Timer ꔅ Schedule List

꘍ Information ꔉ Watch/Schedule ꕉ Exit

5-1 Globo HD

5-2 CCTV-1

7-1 CCTV-2

9-2 BTV-1

9-3 CETV-1

DTV

Racing News

ꔖ DTV 5-1 Globo HD May. 7, 2010 9:30 PM ~ 10:15 PM

Antigues Roadshow Kungskonsumente

No Info TV2: FARMEN No Information

No Information

The Drum

Fashion Essentials

WATCHING TV / CHANNEL CONTROL

Date Setting Mode

GREEN

Switch off Date setting mode.

ENTER

Change to the selected date.

Select a date.

Switch off Date setting mode.

GUIDE

EXIT

Switch off EPG.

Detailed Information Box

Text Up/Down.

Select Remind setting mode.

BACK

GUIDE

INFO

The detail information on or off.

GUIDE

Switch off EPG.

Program Guide

ALL

Fri, May. 7

May. 7, 2010 10:07 PM

10:00 PM

11:00 PM

ꘂ Favorite

ꔅ Mode ꔅ Date

ꔅ Manual Timer ꔅ Schedule List

꘍ Information ꔉ Watch/Schedule ꕉ Exit

5-1 Globo HD

5-2 CCTV-1

7-1 CCTV-2

9-2 BTV-1

9-3 CETV-1

DTV

Racing News

ꔖ DTV 5-1 Globo HD May. 7, 2010 9:30 PM ~ 10:15 PM

Antigues Roadshow Kungskonsumente

No Info TV2: FARMEN No Information

No Information

The Drum

Fashion Essentials

Remind

1 YLE TV 1 25

DT V

Fia World Touring Car Chanpionship

Tue. 25 Nov. 2008 10:05 12:40

Fia Champion

Miss Gotto's Haunted house/Cry of The Swamp; Miss Gotto's

Haunted house/Cry of The Swamp; Miss Gotto's Haunted

house/Cry of The Swamp; Miss Gotto's Haunted house/Cry of

The Swamp; Miss Gotto's Haunted house/Cry of The Swamp;

Miss Gotto's Haunted house/Cry of The Swamp;

25 Nov. 2008 10:05

8 Day Guide Mode

RED

Change EPG mode.

GREEN

Enter Date setting mode.

YELLOW

Enter Manual Timer mode.

BLUE

Enter Schedule List mode.

ENTER

When ‘Currently broadcasting program’ is

selected, it is moved to selected program

and EPG disappears.

When ‘Future broadcasting program’ is

selected, a reservation pop-up window

appears.

Select Programme.

Select the Broadcast Programme.

Program Guide

ALL

Fri, May. 7

May. 7, 2010 10:07 PM

10:00 PM

11:00 PM

ꘂ Favorite

ꔅ Mode ꔅ Date

ꔅ Manual Timer ꔅ Schedule List

꘍ Information ꔉ Watch/Schedule ꕉ Exit

5-1 Globo HD

5-2 CCTV-1

7-1 CCTV-2

9-2 BTV-1

9-3 CETV-1

DTV

Racing News

ꔖ DTV 5-1 Globo HD May. 7, 2010 9:30 PM ~ 10:15 PM

Antigues Roadshow Kungskonsumente

No Info TV2: FARMEN No Information

No Information

The Drum

Fashion Essentials

WATCHING TV / CHANNEL CONTROL

Manual Timer

Fri, May 7, 2010 10:07 PM

ꔂ Move

ꔅ Program Guide ꔅ Schedule List

ꔉ Enter ꕉ Exit

Select the data to schedule.

Free Space 100GB

ꔪ 79h 03m ꔫ 31h 37m

Sun. Mon. Tue. Wed. Thu. Fri. Sat.

No schedule list

Fri, May 7, 2010

Remind Setting Mode

EXIT

Switch off Manual Timer mode.

Select Remind function setting.

Select Start Time or Program.

YELLOW

Change to Guide mode.

BLUE

Change to Schedule List mode.

ENTER

Save Timer Remind.

Schedule List Mode

If you’ve created a schedule list, a scheduled program is displayed at the scheduled time even when

you are watching a different program at the time.

YELLOW

Change to Manual Timer mode.

BLUE

Change to Guide mode.

BACK

Switch off Schedule List.

ENTER

Select your desired Option (Modify/

Delete/Delete All).

Select Schedule List.

Page Up/Down.

Select time to remind,

ꕉ Prev.ꔉ Enter

Start Time Channel

10 : 43 PM

DTV 5-1 Globo HD

Schedule List

Fri, May 7, 2010 10:07 PM

ꔅ Manual Timer ꔅ Program Guide

ꕉ Exit

Free Space 100GB

ꔪ 33h 03m ꔫ 13h 37m

Sun

Mon

Tue

Wed

Thu

Fri

Sat

•

ꔎ

Record (Once)

DTV 11-1

Nov/13/2009(Thu)

5:12 PM ~ 6:02 PM

ꔎ

Start date Start time Title Repeat

04/08 (sun) 23:15 PM TV2: Farmen Sat,Sun

04/02 (Mon) 12:45 AM Racing News Mon

ꔀ Move ꔉ Modify/Delete ꘃ Page Change

5:12 PM ~ 6:02 PM

Modify

Delete

Delete All

ꔡ

ꔉ

ꔠ

ꔡ

WATCHING TV / CHANNEL CONTROL

ꔛ

When new external device is connected, this popup

menu is displayed automatically.

If selecting Yes, you can select input source that you

want to appreciate.

ꔛ

But, when selecting “SIMPLINK - On”, popup menu for

HDMI input will not be displayed.

Disconnected inputs are inactive

(grayed out)

INPUT LIST

Only these input signals which are connected to a TV can be activated and selected.

INPUT

ENTER

Select the desired input source.

ꔛ

TV: Select it to watch over-the-air, cable and digital cable broadcasts.

ꔛ

USB: Select it to use movie, photo, or music files.

ꔛ

AV: Select them to watch a VCR or other external equipment.

ꔛ

Component: Select them to watch DVD or a Digital set-top box.

ꔛ

RGB-PC: Select it to view PC input.

ꔛ

HDMI: Select them to watch high definition devices.

Input List

ꔂ Move ꔉ Enter

TV USB1 USB2 AV Component1 Component2

RGB-PC HDMI1 HDMI2 HDMI3 HDMI4

ꔅ Input Label ꕉ Exit

Yes

New external input is connected.

Do you want to use this?

AV1

i.e)

WATCHING TV / CHANNEL CONTROL

i.e) Change the input label using Blue

button

INPUT LABEL

You can set a label for each input source when it's not in use.

This indicates which device is connected to which input port.

INPUT

Select the desired input

source.

Select the label.

BACK

Return to the previous menu.

EXIT

Return to TV viewing.

BLUE

Input List

ꔂ Move ꔉ Enter

TV USB1 USB2 AV Component1 Component2

RGB-PC HDMI1 HDMI2 HDMI3 HDMI4

Input Label

◀

VCR

▶

Component1

◀▶

Component2

◀▶

RGB-PC

◀▶

HDMI1

◀▶

ꔍ

ꔅ Input Label ꕉ Exit

i.e)

WATCHING TV / CHANNEL CONTROL

MODE SETTING

Default selection is “Home Use”. We recommend setting the TV to “Home Use” mode for the best

picture in your home environment.

ꔛ

“Store Demo” Mode is only intended

for use in retail environments.

Customers can adjust the “Picture

menu - Picture mode” manually while

inspecting the TV, but the TV will

automatically return to preset in-

store mode after 5 minutes.

ꔛ

“Store Demo” Mode is an optimal

setting for displaying at stores. “Store

Demo” mode initializes the TV to set

the image quality.

Select OPTION.

ENTER

Select Mode Setting.

ENTER

Select Home Use.

BACK

Return to the previous menu.

EXIT

Return to TV viewing.

OPTION

ꔂ Move ꔉ Enter

OPTION

ꔂ Move ꔉ Enter

• Language

• Caption : Off

• Power Indicator

• Initial Setting

• Set ID : 1

• Mode Setting : Home Use

ꔉ

ꔠ

• Language

• Caption : Off

• Power Indicator

• Initial Setting

• Set ID : 1

• Mode Setting : Home Use

Selecting the environment.

Choose the setting mode you want.

Select [Home Use] to use this TV at home. To use

this TV in store, select [Store Demo].

Home Use Store Demo

• Demo Mode Off

WATCHING TV / CHANNEL CONTROL

DEMO MODE

Displays a slide show to explain the various feature of this TV.

OPTION

ꔂ Move ꔉ Enter

• Language

• Caption : Off

• Power Indicator

• Initial Setting

• Set ID : 1

• Mode Setting : Store Demo

OPTION

ꔂ Move ꔉ Enter

ꔉ

ꔠ

• Language

• Caption : Off

• Power Indicator

• Initial Setting

• Set ID : 1

• Mode Setting : Home Use

Selecting the environment.

Choose the setting mode you want.

Select [Store Demo] to use this TV in store. To

this TV at home, select [Home Use].

Home Use Store Demo

• Demo Mode Off

Select OPTION.

ENTER

Select Mode Setting.

ENTER

Select Store Demo.

ENTER

Select On.

EXIT

Return to TV viewing.

After a while, Demo Mode. starts.

If you want to stop the demo, press any

button (Except VOL +, - and MUTE button).

WATCHING TV / CHANNEL CONTROL

INITIAL SETTING (RESET TO FACTORY DEFAULT)

This function resets the TV to factory default and erases all stored channels.

ꔛ

When selecting “Lock System - On”

in the LOCK menu, the message to

enter the password appears.

ꔛ

If you forget your password, press

“0-3-2-5” on the remote control.

OPTION

ꔂ Move ꔉ Enter

• Language

• Caption : Off

• Power Indicator

• Initial Setting

• Set ID : 1

• Mode Setting : Home Use

Select OPTION.

ENTER

Select Initial Setting.

ENTER

Select Yes.

ENTER

TV turns off automatically and start

factory reset.

Yes

All user settings and channel settings will

be reset. Still continue?

OPTION

ꔂ Move ꔉ Enter

ꔀ

ꔉ

• Language

• Caption : Off

• Power Indicator

• Initial Setting

• Set ID : 1

• Mode Setting : Home Use

WATCHING TV / CHANNEL CONTROL

Off

Cinema

Game Sport

AV MODE

AV Mode toggles through preset Video and Audio settings.

AV MODE

Press the AV MODE button repeatedly to

select the desired source.

ENTER

ꔛ

If you select “Cinema” in AV mode,

Cinema will be selected both for

“PICTURE menu - Picture Mode”

and “AUDIO menu - Sound Mode”

respectively.

ꔛ

If you select “Off” in AV mode, the

“Picture Mode” and “Sound Mode”

return to previous selected value.

ꔛ

Off: Disables the AV MODE.

ꔛ

Cinema: Optimizes video and audio

for watching movies.

ꔛ

Sport: Optimizes video and audio for

watching sports events.

ꔛ

Game: Optimizes video and audio for

playing games.

When playing a video game using

PlayStation or Xbox, it is recom-

mended to use the Game mode.

When in Game mode, functions

related to picture quality will be opti-

mized for playing games.

WATCHING TV / CHANNEL CONTROL

SIMPLINK

SIMPLINK allows you to control and play other AV devices connected with HDMI cable without addi-

tional cables and settings. This TV may work with devices with HDMI-CEC support, but only devices

with the

logo are fully supported.

SIMPLINK can be turned on and off in the user menus.

Display SIMPLINK menu.

Select On.

ENTER

Select the desired device.

ENTER

Control connected AV devices.

ꔉ Enter ꕉ Exit

◀ On ▶

Watch TV

◀ ▶

HDD Recorder

◀ ▶

DISC 1

HDD/DVD-R

VCR 1

HD HT

Speaker

TV Speaker

ꔉ Enter ꕉ Exit

◀ On ▶

Watch TV

◀ ▶

HDD Recorder

◀ ▶

DISC 1

HDD/DVD-R

VCR 1

HD HT

Speaker

TV Speaker

TV viewing: Switch to the previous TV

channel regardless of the current

mode.

DISC playback: Select and play discs.

When multiple discs are available, the

disc devices are conveniently displayed

at the bottom of the screen.

VCR playback: Control the connected

VCR.

HDD Recordings playback: Control

recordings stored in HDD.

Audio Out to Home Theater speaker/

Audio Out to TV: Select Home Theater

speaker or TV speaker for Audio Out.

►

When no device is con-

nected (displayed in gray)

►

Selected Device

►

When a device is conect-

ed (displayed in bright

color)

WATCHING TV / CHANNEL CONTROL

SIMPLINK Functions

ꔛ

Direct Play: After connecting AV devices to the TV, you can directly control the devices and play media

without additional settings.

ꔛ

Select AV device: Enables you to select one of the AV devices connected to the TV.

ꔛ

Disc playback: Control connected AV devices by pressing the ꕌꕍ

< >

, ENTER, ꕖ, ꕗ, ꕘ, ꕚ and ꕙ but-

tons.

ꔛ

Power off all devices: When you power off the TV, all connected devices are turned off.

ꔛ

Switch audio-out: Offers an easy way to switch audio-out.

ꔛ

Sync Power on: When the equipment with Simplink function connected HDMI terminal starts to play,

The TV will automatically turn on.

Note: To operate SIMPLINK, an HDMI cable over Version 1.3 with *CEC function should be used. (*CEC:

Consumer Electronics Control).

(A device, which is connected to the TV through a HDMI cable but does not support SIMPLINK, does

not provide this function)

NOTE

► Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal (HDMI terminal) of

the SIMPLINK device with the HDMI cable

► When you switch the Input source with the INPUT button on the remote control, the SIMPLINK

device will stop.

► When you select a device with home theater functionality, the sound output automatically switches

to the home theater speakers and the TV speakers are turned off.

► If a connected SIMPLINK home theater system doesn’t play the audio from the TV, connect the

DIGITAL AUDIO OUT terminal on the back of the TV to the DIGITAL AUDIO IN terminal on the

back of the SIMPLINK device with an OPTICAL cable.

MY MEDIA

MY MEDIA (EXCEPT 42/50PJ230, 32LD350)

CONNECTION METHOD

USB Connection

Connect the USB device to the USB IN jack on the TV.

USB IN

N 3

Memory Key

Precautions when using the USB device

►Only a USB storage device is recognizable.

►Connecting a USB storage device through a USB hub is not supported.

►A USB storage device which uses its own driver may not be recognized.

►The recognition speed of a USB storage device may depend on each device.

► Please do not turn off the TV or unplug the USB device when the connected USB storage device

is working. When such device is suddenly separated or unplugged, the stored files or the USB

storage device may be damaged.

►Only use a USB storage device which has normal music files or image files.

►Please use only a USB storage device which was formatted as a FAT 32 or NTFS file system pro-

vided with the Windows operating system. Others may not be recognized.

►Some USB storage devices require a power adapter. The power adapter must be connected in

order to be seen by the TV.

►If a device is not recognized by the TV, try a different cable. Excessively long cables are not sup-

ported.

►Some USB storage devices may not be supported or operate properly.

►Please backup important files because data on USB device could be damaged. Data management

is consumer's responsibility and as a result, the manufacturer does not cover data damage.

►If your USB memory device has multiple partitions, or if you use a USB multi-card reader, you can

use up to 4 partitions or USB memory devices.

►File alignment method of USB storage device is similar to Window XP and file names can be up

to 100 English characters.

►The recommended capacity is 1TB or less for a USB external hard disk and 32 GB or less for USB

memory.

►If a USB external hard disk with a “Energy Saving” function doesn’t work, turn the hard disk off and

on again to make it work properly. Refer to the user manual of the USB external hard disk.

►USB storage devices below USB 2.0 are supported as well. But they may not work properly in the

movie list.

MY MEDIA

ENTRY MODE

The My Media menu will open automatically when you insert a USB drive. My Media can also be

accessed by choosing My Media in the user menu.

On USB device, you can not add a new folder or delete the existing folder.

When removing the USB device

Select the USB Device menu before

removing the USB device.

ꔛ

This TV can view JPG image files, HD DivX

files or play MP3 audio files.

Q.MENU

Select USB Device.

ENTER

Select Eject.

Select MY MEDIA.

ENTER

Select Movie List, Photo

List, Music List or Extra

Contents.

ENTER

Movie List

MY MEDIA

Photo List Music List

Extra Contents

For 32/42LD460H

MY MEDIA

MOVIE LIST

Precautions when playing the video files

►Some user-created subtitles may not work properly.

►Some special characters are not supported in subtitles.

►HTML tags are not supported in subtitles.

►Time information in an external subtitle file should be arranged in ascending order to be played.

►The screen may suffer temporary interruptions (image stoppage, faster playback, etc.) when the

audio language is changed.

►A damaged video file may not be played correctly, or some functions may not be usable.

►Video files produced with some encoders may not be played correctly.

►If the video and audio structure of recorded file is not interleaved, the file not playback properly.

►Video with resolution higher than maximum resolution supported for each frame, cannot be guar-

anteed for smooth playback.

►Movie files other than the specified types and formats may not work properly.

►The movie file encoded by the GMC (Global Motion Compensation) is not supported.

►Only the files saved in ASCII Code is supported in subtitles.

►Only 250 Korean characters, 500 letters and 500 numbers are supported for each line of the

subtitle.

►Only 10,000 sync blocks are supported within the subtitle file.

►We do not guarantee smooth playback of profiles encoded level 4.1 or higher in H.264.

►DTS Audio codec is not supported.

►A video file more than 30GB in file size is not supported for playback.

►Playing a video via a USB connection that doesn’t support high speed may not work properly.

►USB storage devices below USB 2.0 are supported as well. But they may not work properly in the

movie list.

►The video file and its subtitle file must be located in the same folder.

At this time, a video file name and its subtitle file name must be identical for it to be displayed.

►When you are watching a movie via the Movie List function, you can adjust the picture with the

ENERGY SAVING and AV MODE button on the remote control. User setup for each picture mode

is not supported.

The movie list is activated once a USB drive is detected. It is used when playing movie files on the TV.

It displays all of the video files it recognizes.

The On-Screen Display on your model may be slightly different.

Supported movie file

ꔛ

Resolution: under 1920 pixel (width) x 1080 pixel (height)

ꔛ

Frame Rate: under 30 frame/sec (1920x1080), under 60 frame/sec (1280x720)

ꔛ

Max bitrate of playable movie file: 20 Mbps (Mega bit per second)

ꔛ

Bit rate of audio format: within 32 kbps to 320 kbps (MP3)

ꔛ

Supported subtitle format: *.smi, *.srt, *.sub (MicroDVD, SubViewer 1.0/2.0), *.ass, *ssa, *txt

(TMPlayer), *.psb (PowerDivX)

MY MEDIA

Supported Video Formats

File

Extension name

Video Decoder Audio Codec Max Resolution

mpg, mpeg MPEG1, MPEG2 MP2, MP3, Dolby Digital, LPCM

1920 x 1080 @ 30p

(Only Motion JPEG

640x480@30p)

dat MPEG1 MP2

ts, trp, tp MPEG2, H.264, AVS, VC1

MP2, MP3, Dolby Digital, AAC,

HE-AAC

vob MPEG1, 2 MP2, MP3, Dolby Digital, LPCM

mp4, mov

MPEG4,DivX 3.11, DivX 4.12, DivX 5.x,

DivX 6, Xvid 1.00, Xvid 1.01, Xvid 1.02,

Xvid 1.03, Xvid 1.10-beta1/2H.264

AAC, HE-AAC, MP3

mkv H.264, MPEG-1,2,4

MP2, MP3, Dolby Digital, AAC

HE-AAC, LPCM

divx, avi

MPEG2, MPEG4, DivX 3.11, DivX 4,

DivX 5, DivX 6, Xvid 1.00, Xvid 1.01,

Xvid 1.02, Xvid 1.03, Xvid

1.10-beta1/2H.264

MP2, MP3, Dolby Digital,

LPCM,

ADPCM, AAC, HE-AAC

Motion JPEG

(avi, mp4, mkv)

JPEG LPCM, ADPCM

asf, wmv VC1 WMA

flv Sorenson H.263, H264 MP3, AAC

MY MEDIA

Select MY MEDIA.

Select Movie List.

ENTER

Moves to upper level folder

Current page/Total pages

Corresponding buttons on the

remote control

Contents under the folder

focused on

Current page/total pages of

contents

Screen Components

Page 1/1

Movie List

Page 1/1USB 1 XTICK

ꔂ Move ꔉ Play ꘃ Page Change ꘁ Mark

Drive1

M1 M2 M3 M4

Butterfly_...

01:34:33

ꔅ To Photo List ꔅ Change Numbers ꔅ Mark Mode ꕯ Exit

GREEN

Move to Photo List or Music List.

YELLOW

Change Numbers: Changes the number or thumbnails displayed at a time.

BLUE

Allows you to mark certain files.

EXIT

Return to TV viewing.

MY MEDIA

ꔛ

Use the CH

(

ꕌꕍ)

button to navigate

in the movie page.

ꔛ

When one or more movie files are

marked, the marked movies will be

played in sequence.

Select the target folder or

drive.

ENTER

Select the desired

movie title.

FAV

MARK

Mark your desired movie file.

RED

Play the marked movie file.

It displays the current movie

status progress bar on the bot-

tom of the screen.

Movie Selection

Mark Mode

RED

Play Marked: Play the first selected file. Once

a movie finishes playing, the next selected

one will be played automatically.

GREEN

Mark All: Mark all files in the folder.

YELLOW

Unmark All: Deselect all marked files.

BLUE

Exit the Mark Mode.

Page 1/1

Movie List

Page 1/1USB 1 XTICK

ꔂ Move ꔉ Play ꘃ Page Change ꘁ Mark

Drive1

M1 M2 M3 M4

Butterfly_...

01:34:33

Page 1/1

Movie List

Page 1/1

USB 1 XTICK

ꔂ Move ꔉ Mark ꘃ Page Change ꘁ Mark

Drive1

M1 M2 M3 M4

Butterfly_...

01:34:33

Select the target folder or drive.

ENTER

Select the desired

movie title.

ENTER

Play the movie file.

Mark Mode

ꔅ To Photo List ꔅ Change Numbers ꔅ Mark Mode ꕯ Exit

ꔅ Play Marked ꔅ Mark All ꔅ Unmark All ꔅ Exit Mark Mode ꕯ Exit

ꔊꔋ

ꕗꕖꕘꕚꕙꕊ꘩ Option ꕉ Hide ꕯ Exit

Choose options.

Set Video Play.

Set Video.

Set Audio.

EXIT

Return to TV viewing.

Select the required speed: x2, x4, x8, x16, x32 (backward/forward).

Pauses the media player.

If no buttons are pressed on the remote control for 10 minutes after pausing, the

TV returns to the playback state.

Displays a slow motion.

Move to a specific frame forward or backward while playing a video. A cursor indi-

cating the position can be viewed on the screen. It may not work properly for

some movie files.

Return to normal playback.

BACK

Hide the menu on screen. To see the menu again, press ENTER button to display.

ENERGY

SAVING

Press the ENERGY SAVING button repeatedly to increase the brightness of your

screen (Refer to p.116).

AV MO D E

Press the AV MODE button repeatedly to select the desired source (Refer to p.87).

Using the remote control

Using the Movie List Function

Q.MENU

Show the Option menu.

ENTER

Select Set Video Play., Set Video, or

Set Audio.

NOTE

►

When replaying a video file after stop-

ping, you can play from where it stopped

automatically.

►

If you select “Yes” when playing the

same file after the video file has been

stopped, it will restart where it stopped

previously.

►

If continuous series files exist within the

folder, the next file will automatically be

played.

But, this excludes cases when

the Repeat function of Movie List Option

is turned “On” (Refer to page 97) or

when set as Marked Play.

MY MEDIA

Set Video Play Menu Options

Set Video Play.

Picture Size

◀

Full

▶

Audio Language

◀

▶

Subtitle

◀

▶

• Language

◀

Unknow

▶

• Code Page

◀

Default

▶

• Sync

◀

▶

• Position

◀

▶

• Size

◀

Normal

▶

Repeat

◀

Off

▶

ꕉ Previous

Subtitle Language Group Supported Language

Latin1 English, Spanish, Portuguese

ꔛ

Picture Size: Selects your desired

picture format for videos.

ꔛ

Audio Language: Changes the

Language Group of the audio for

video files.

ꔛ

Subtitle Language: The subtitles can

be turned on or off. If there are two

or more subtitles, you can select one

of them.

ꔛ

Language: Activated for SMI subtitles

and can select the language within

the subtitle.

ꔛ

Code Page: Subtitle font selection.

When set to default, same font as

general menu will be used.

ꔛ

Sync: When the video is not synchro-

nized with the captions, it can be

adjusted by 0.5 second.

ꔛ

Position: Move the location of the

subtitles.

ꔛ

Size: Changes the subtitle font size.

ꔛ

Repeat: Turn on/off repeat function

of movie playback. When turned on,

the file within the folder will be played

back repeatedly.

Select Picture Size, Audio Language,

Subtitle, or Repeat.

Make appropriate adjustments.

Code Page

MY MEDIA

Set Audio Menu Options

Set Audio.

Sound Mode

◀

Standard

▶

Auto Volume

◀

Off

▶

Clear Voice II

◀

Off

▶

Balance 0

◀▶

ꕉ Previous

Select Picture Mode or TruMotion.

Make appropriate adjustments.

BLUE

Reset picture settings to default.

Select Sound Mode, Auto Volume, Clear

Voice II or Balance.

Make appropriate adjustments.

Set Video Menu Options

Set Video.

Picture Mode

◀

Standard

▶

• Backlight 70

◀▶

• Contrast 100

◀▶

• Brightness 50

◀▶

• Color 60

◀▶

• Dynamic Contrast

◀

Medium

▶

• Edge Enhancer

◀

High

▶

• Noise Reduction

◀

Medium

▶

TruMotion

◀

Low

▶

ꔅ Picture Reset ꕉ Previous

('TruMotion'

dependending on models)

Set Video.

Picture Mode

◀

Standard

▶

• Contrast 100

◀▶

• Brightness 50

◀▶

• Sharpness 50

◀▶

• Color 60

◀▶

• Tint 0

◀▶

• Color Temp. 0

◀▶

• Noise Reduction

◀

Low

▶

ꔅ Picture Reset ꕉ Previous

For Plasma TV

For LED LCD TV/LCD TV

MY MEDIA

The On-Screen Display on your model may be slightly different.

PHOTO LIST

Screen Components

Supported photo file: *.JPG

ꔛ

Baseline: 64 pixel (width) x 64 pixel (height) to 15360 pixel (width) x 8640 pixel (height)

ꔛ

Progressive: 64 pixel (width) x 64 pixel (height) to 1920 pixel (width) x 1440 pixel (height)

ꔛ

You can play JPEG files only.

ꔛ

Non-supported files are displayed in the form of predefined icon.

Select MY MEDIA.

Select Photo List.

ENTER

Moves to upper level folder

Current page/total pages

Corresponding buttons on the

remote control

Contents under the folder

focused on

Current page/total pages of

contents

Page 1/1

Photo List

Page 1/1

Drive1

P1 P2 P3 P4 P5 P6 P7 P8 P9

P10 P11 P12 P13 P14 P15

USB 1 XTICK

ꔂ Move ꔉ View ꘃ Page Change ꘁ Mark

ꔅ To Music List ꔅ Change Numbers ꔅ Mark Mode ꕯ Exit

GREEN

Move to Music List or Movie List.

YELLOW

Change Numbers: Changes the number or thumbnails displayed at a time.

BLUE

Allows you to mark certain files.

EXIT

Return to TV viewing.

MY MEDIA

100

Photo Selection

ꔛ

Use the CH

(

ꕌꕍ)

button to navigate

in the photo page.

ꔛ

When one or more photos are

marked, you can view individual pho-

tos or a slide show of the marked

photos. If no photos are marked, you

can view all photos individually or all

photos in the folder in a slide show.

Select the target folder or drive.

ENTER

Select the desired

photo files.

FAV

MARK

Mark your desired photo files.

RED

View the marked photo files.

Mark Mode

RED

View Marked: Display the selected photo.

GREEN

Mark All: Mark all photos on the screen.

YELLOW

Unmark All: Deselect all marked photos.

BLUE

Exit the Mark Mode.

Select the target folder or drive.

ENTER

Select the desired pho-

tos.

ENTER

Photo file is displayed.

Page 1/1

Photo List

Page 1/1

Drive1

USB 1 XTICK

ꔂ Move ꔉ View ꘃ Page Change ꘁ Mark

ꔅ To Music List ꔅ Change Numbers ꔅ Mark Mode ꕯ Exit

Page 1/1

Photo List

Page 1/1

Drive1

USB 1 XTICK

ꔂ Move ꔉ Mark ꘃ Page Change ꘁ Mark

Mark Mode

ꔅ View Marked ꔅ Mark All ꔅ Unmark All ꔅ Exit Mark Mode ꕯ Exit

101

MY MEDIA

How to View Photos

Detailed operations are available on full-sized photo view screen.

The aspect ratio of a photo may change the size of the

photo displayed on the screen in full size.

Select the target folder or drive.

ENTER

Select the desired photos.

ENTER

The selected photo is displayed in full

size.

ꔛ

Use the CH

(

ꕌꕍ)

button to navigate

in the photo page.

◀▶

01_a.jpg

2008/12/10

1920 x 1080

479 KB

Slideshow ꘡ BGM ꘡ ꘤ ꔦ ꕊ ꘩ Option ꕉ Hide ꕯ Exit

◀

2/13

▶

Page 1/1

Photo List

Page 1/1

Drive1

USB 1 XTICK

ꔂ Move ꔉ View ꘃ Page Change ꘁ Mark

ꔅ To Music List ꔅ Change Numbers ꔅ Mark Mode ꕯ Exit

MY MEDIA

102

◀▶

01_a.jpg

2008/12/10

1920 x 1080

479 KB

◀

2/13

▶

► Slideshow: Selected photos are displayed during the slide show. If no photo is selected, all photos

in the current folder are displayed during slide show.

ꔛ

Set the time interval of the slide show in Option-Set Photo View. menu (Refer to p.103).

ꔛ

You can adjust Option by using the Q.MENU button on the remote control.

►

BGM (Background Music): Listen to music while viewing photos in full size.

ꔛ

Set the BGM device and album in in Option-Set Photo View. menu (Refer to p.103).

ꔛ

You can adjust Option by using the Q.MENU button on the remote control.

►

꘤ (Rotate) : Rotate photos.

ꔛ

Rotates the photo 90°, 180°, 270°, 360° clockwise.

ꔛ

Photos cannot be rotated if its width is greater than the available supported resolution height.

►

ꔦ (Zoom In): View the photo by zoom in 2, 4 times by using Blue button.

►

ꕊ (Energy Saving): Increase the brightness of your screen by using ENERGY SAVING button.

►

Option : Set values for Slide Speed and Music Folder (Refer to p.103).

ꔛ

You cannot change Music Folder while BGM is playing.

ꔛ

You can only select the MP3 folder saved on the device that currently displays the photo.

► Hide : Hide the menu on the full-sized screen.

ꔛ

To see the menu again on the full-sized screen, press ENTER button to display.

► Exit : Move to the previous menu screen.

ꔛ

Use

< >

button to select the previ-

ous or next photo.

ENTER

Select the Slideshow,

BGM,

꘤ (Rotate),

ꔦ (Zoom In), ꕊ (Energy Saving),

Option, or Hide

Slideshow ꘡ BGM ꘡ ꘤ ꔦ ꕊ ꘩ Option ꕉ Hide ꕯ Exit

103

MY MEDIA

Using the Photo List Function

NOTE

►

Option values changed in Photo List do

not affect Movie List and Music List.

►

Option values changed in Photo List or

Music List are changed likewise in Photo

List and Music List, but not Movie List.

Set Photo View Menu Options

Set Photo View.

Slide Speed

◀

Fast

▶

Music Folder

Drive1

• Repeat

◀

▶

• Random

◀

Off

▶

ꕉ Previous

Q.MENU

Show the Option menu.

ENTER

Select Set Photo View., Set Video or

Set Audio.

Select Slide Speed or Music Folder.

Make appropriate adjustments.

◀▶

01_a.jpg

2008/12/10

1920 x 1080

479 KB

Slideshow ꘡ BGM ꘡ ꘤ ꔦ ꕊ ꘩ Option ꕉ Hide ꕯ Exit

◀

2/13

▶

Choose options.

Set Photo View.

Set Video.

Set Audio.

MY MEDIA

104

Set Video Menu Options

Set Audio Menu Options

Set Audio.

Sound Mode

◀

Standard

▶

Auto Volume

◀

Off

▶

Clear Voice II

◀

Off

▶

Balance 0

◀▶

ꕉ Previous

Select Picture Mode or TruMotion.

Make appropriate adjustments.

BLUE

Initialize the adjusted picture value.

Select Sound Mode, Auto Volume, Clear

Voice II or Balance.

Make appropriate adjustments.

Set Video.

Picture Mode

◀

Standard

▶

• Backlight 70

◀▶

• Contrast 100

◀▶

• Brightness 50

◀▶

• Color 60

◀▶

• Dynamic Contrast

◀

Medium

▶

• Edge Enhancer

◀

High

▶

• Noise Reduction

◀

Medium

▶

TruMotion

◀

Low

▶

ꔅ Picture Reset ꕉ Previous

('TruMotion'

dependending on models)

Set Video.

Picture Mode

◀

Standard

▶

• Contrast 100

◀▶

• Brightness 50

◀▶

• Sharpness 50

◀▶

• Color 60

◀▶

• Tint 0

◀▶

• Color Temp. 0

◀▶

• Noise Reduction

◀

Low

▶

ꔅ Picture Reset ꕉ Previous

For Plasma TV

For LED LCD TV/LCD TV

105

MY MEDIA

MUSIC LIST

Purchased music files(*.MP3) may contain copyright restrictions. Playback of these files may not be

supported by this TV.

The On Screen Display below may be different from your TV. Images are an example to assist with

the TV operation.

MUSIC (*.MP3) supporting file

Bit rate 32 Kbps ~ 320 Kbps

• Sampling rate MPEG1 Layer3 : 32kHz, 44.1kHz, 48kHz

• Sampling rate MPEG2 Layer3 : 16kHz, 22.05kHz, 24kHz

• Sampling rate MPEG2.5 Layer3 : 8kHz, 11.025kHz, 12kHz

Screen Components

Select MY MEDIA.

Select Music List.

ENTER

Preview: If any album jacket for

the file (Album Art Image)

exists, this picture is displayed.

Moves to upper level folder

Current page/Total pages

Corresponding buttons on the

remote control

Contents under the folder

focused on

Current page/total pages of

contents

Page 1/1

Music List

Page 1/1

001. - B01 .mp3