Sears 580.73083300 El manual del propietario

Marca: Sears

Modelo: 580.73083300

Categoría: Acondicionadores de aire de sistema dividido

Tipo: El manual del propietario

Este manual también es adecuado para

Owner's Manual

Manual del Propietario

THROUGH-THE-WALLAIRCONDITIONER

ACONDICIONADODEAIREATRAVESDEPARED

Model, Modelo 580.73083 580.74103 580.74123

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www.sears.com

TABLE OF CONTENTS ........................2

WARRANTY ..............................................2

SAFETY .....................................................3

ImportantSafety Instructions...................... 3

ELECTRICAL REQUIREMENTS .......4

INSTALLATION ........................................5

Installation Requirements ......................... 5

Installation ................................................ 6

Procedure A ............................................. 7

Procedure B ............................................. 9

Procedure C .......................... ._............... 11

OPERATION ........................................... 12

How and Why ......................................... 12

Normal Sounds ...................................... 12

Capacity and Running Time ................... 12

Features ................................................. 13

Using the Air Conditioner ....................... 13

Air Conditioner Features ........................ 14

MAINTENANCE ..................................... 17

Air Filter Cleaning ................................... 17

Air Conditioner Cleaning ........................ 17

How to Remove the Front Grille ............. 17

How to Replace the Front Grille ............. 17

TROUBLESHOOTING ......................... 18

Before Calling for Service ...................... 18

ESPAI_IOL ................................................ 2o

MASTER PROTECTION

AGREEMENTS ......................................39

SERVICE NUMBERS ............BackCover

FULL ONE YEAR WARRANTY ON

THROUGH-THE-WALL AIR CONDITIONER

For one year from the date of purchase, when this

air conditioner is operated and maintained for

normal room cooling according to instructions in this

owner's manual, Sears will repair this air

conditioner, free of charge, if defective in material or

workmanship.

FULL FIVE-YEAR WARRANTY ON

SEALED REFRIGERATION SYSTEM

For five years from the date of purchase, when this

air conditioner is operated and maintained for

normal room cooling according to instructions in this

owner's manual, Sears will repair the sealed

refrigeration system (consisting of refrigerant,

connecting tubing, and compressor), free of charge,

if defective in material or workmanship.

WARRANTY SERVICE IS AVAILABLE BY

CONTACTING SEARS SERVICE AT

1-800-4-MY-HOME ®.

Warranty coverage applies only to air conditioners

used for non-commercial, private household

purposes.

This warranty applies onlywhile this product is in

use in the United States.

This warranty gives you specific legal rights, and

you may also have other rights which vary from

state to state.

Sears, Roebuck and Co., D/817WA,

Hoffman Estates, IL 60179 U.S.A.

-2-

IMPORTANT SAFETY INSTRUCTIONS

The safety instructions below will tell you how to use your room air conditioner to avoid harm to yourself or

damage to yourROOM AIRCONDITIONER.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable

vapors and liquids in the vicinityof this or any other

appliance. Read product labels for flammability and

other warnings.

PREVENT ACCIDENTS

To reduce the risk of fire, electrical shock, or injury

to persons when using your air conditioner, follow

basic precautions, including the following:

• Be sure the electrical service is adequate for the

model you have chosen.

• If the air conditioner is to be installed in a window,

you will probably want to clean both sides of the

glass first. If the window is a triple-track type with a

screen panel included, you may want to remove

the screen completely before installation.

• Be sure the air conditioner has been securely and

correctly installed according to the instructions in

this manual.

Save this manual and installation instructions for

possible future use in removing or reinstalling this

unit.

• Use gloves when handling the air conditioner.

Be careful to avoid cuts from sharp metal fins on

front and rear coils.

Y_ ELECTRICAL INFORMATION

The complete electrical rating of your new room air

conditioner is stated on the serial plate. Refer to the

rating when checking the electrical requirements.

• Be sure the air conditioner is properly grounded.

To minimize shock and fire hazards, proper

grounding is important. The power cord is

equipped with a three-prong grounding plug for

protection against shock hazards.

• Your air conditioner must be plugged into a

properly grounded wall receptacle. If the wall

receptacle you intend to use is not adequately

grounded or protected by a time delay fuse or

circuit breaker, have a qualified electrician install

the proper receptacle.

• Do not run air conditioner with packing sheet of

the back of the sleeve, and packing corner and

blue tape of the air conditioner. This could result in

mechanical damage within the air conditioner.

• Do not use an extension cord or an adapter

plug.

_ Avoid fire hazard or electric shock.

Do not use an extension cord or an adapter plug.

Do not remove any prong from the power cord.

Grounding type

walkreceptacle Do not under any

circumstances cut,

remove, or bypass

the grounding prong

from this plug.

P°wet;,%;o Zr

grounding plug

ENERGY SAVING IDEAS

• The capacity of the room air conditioner must fit

the room size for efficient and satisfactory

operation.

• Install the room air conditioner on the shady side

of your home. A window that faces north is best

because it is shaded most of the day.

• Do not block air flow inside with blinds, curtains, or

furniture; or outside with shrubs, enclosures, or

other buildings.

• Close the floor and wall registers and the fireplace

damper so cool air does not escape up the

chimney and into the duct work.

• Keep blinds and drapes in other windows closed

during the sunniest part of the day.

• Clean the air filter as recommended in the

MAINTENANCE section of this manual.

• Proper insulation and weather stripping in your

home will help keep warm air out and cool air in.

• External house shading with trees, plants or

awnings will help reduce the air conditioner's work

load.

• Operate heat producing appliances such as

ranges, washers, dryers, and dishwashers during

the coolest part of the day.

-3-

OBSERVE ALL LOCAL CODES AND

ORDINANCES.

DO NOT, UNDER ANY CIRCUMSTANCES,

REMOVE THE POWER SUPPLY CORD

GROUND PRONG,

ELECTRICAL GROUND IS REQUIRED ON

THIS APPLIANCE.

A 208/230-volt 60 Hz, AC only, 15A fused and

properly grounded electrical supply is required.

A time delay fuse or time delay circuit breaker

is recommended. Use a dedicated circuit,

serving only this appliance.

DO NOT USE AN EXTENSION CORD.

RECOMMENDED GROUNDINGMETHOD

For your personal safety, this appliance must

be grounded. This appliance has a power

supply cord with a 3-prong grounding plug. To

minimize possible shock hazard, the cord must

be plugged into a mating grounding type wall

receptacle and grounded in accordance with

the National Electrical Code (ANSI/NFPA 70)

latest edition and all local codes and

ordinances. If a mating wall receptacle is not

available, itis the personal responsibility and

obligation of the customer to have a properly

grounded 3-prong wall receptacle installed by a

qualified electrician.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructionscan result

in death, fire, or electrical shock.

Ground

prong I'/ "_ _)

r I",_ _1 _-3-pr°ng

3 ron _-, _ \'--J J grounding

"P g I I tvee wall

grounding ]_ _ i[ ---

plug receptacle

Power_

supply

cord

-4-

Removepackingsheetfrom the backofthe sleeve,and

packingcomer and bluetape fromthe airconditioner.

INSTALLATION REQUIREMENTS

If you use an existing wall sleeve, youshould

measureitsdimensions.

Install thenewairconditioneraccordingtothese

installationinstructionsto achievethebest

performance.Allwallsleevesusedto mountthe

newairconditionermustbe ingoodstructural

conditionand havea reargrilletosecurelyattach

thenewairconditioner.(FIG. 1)

With the Kenmoresleeve, youcanmaintainthe

bestperformanceofthenewair conditioner.(FIG.2)

(366ram)

!8"(458 ram)

Air Conditioner . FIG. 1

INSTALLATION HARDWARE

2Size options

ITEM NAMEOF PARTS Oq'Y

O PLASTIC GRILLE f

HORIZONTALINSULATION STRIPS 2

_) AROUND INSULATION STRIPS 2

_) SUPPORT BLOCK 2

BAFFLE 1

(_ TRIM FRAME 2

(_ SHIM 2

(_) PLASTICNUTSAND WASHERSCREWS 4

Expanded

aluminum metal g_itlc

/. (425m'_l

Kenmore Wall Sleeve FIG.2

ELECTRICAL SERVICE

Check your available electrical service. The power

supply available must be the same as that shown

on the unit nameplate (found on left side ofcabinet).

All models are equipped with a 3-prong service plug

to provide proper service and safe positive

grounding. Do not change plug in any way. Do not

use an adapter plug. If your present wall outlet does

not match your plug, calf a qualified electrician to

make the necessary corrections. SAVE CARTON

for storage and this OWNER'S MANUAL for future

reference. The carton is the best way to store unit

during winter or when not in use.

To avoid risk of personalinjury, property damage,

or product damage due to the weightofthis

device and sharp edges that maybe exposed:

• Air conditioners covered in this manualpose an

excessive weight hazard. Two or more people

are needed to move and install the unit.

To prevent injury or strain, use proper lifting and

carrying techniques when moving unit.

• Carefully inspectlocation where air conditioner

will be installed. Be sure itwill support the weight

of the unit overan extended period of time.

•Handle air conditioner with care. Wear

protective gloves whenever lifting or carrying the

unit. AVOID the sharp metal fins of front and

rear coils.

• Make sureair conditioner does not fall during

installation.

REQUIRED TOOLS:

• Tight Fitting gloves

• Standard screwdriver

• Phillips screwdriver

• Pliers

• Sharp knife

• 3/8-inch open end

wrench or adjustable

wrench

• 1/4-inch hex socket

and ratchet

• Tape measure

• Electric drill

• 1/4-inch drill bit

-5-

INSTALLATION

We strongly recommend the removalof the

old wall sleeveand the installation of a new

Kenmore Wall Sleeve.

If youdecideto keepthe existingwallsleeve,

youhavetoredirectthe louversat thebackofthe

wall sleeveillustration.The useofpliersis

recommended.Ifyou DO NOT redirect,you run

theriskof poorperformanceor productfailure.

Thisisnotcoveredunderthetermsofthe

Kenmorewarranty.

• Pick a location which will allow the conditioned air

to blow into the area you want. Good installation

with special attention to the proper position of the

unit will lessen the chance that service will be

needed.

ITEMS IN INSTALLATION HARDWARE

You may not need all parts in the kit. Discard

unused pads

ITEM (inches)

Plastic grille 263/4x 161/2

Horizontal Insulation Stripe113/8x s/8x

273/16

13/8 X 13/8 X 273/16

Around Insulation Strips 13/8x 3/4x 611/2

1% x 1% x 611/2

Support Block 13/4x 1% x 451m

Baffle 14 x 41/2x 1/8

Shim 13x lx3/4

Trim Frame

Washer Screw

Nuts(Plastic)

Qty.

HOW TO INSTALL

li]l Identify the existing wall sleeve before installing

the unitfrom the listed below.

Brand

White-Westinghous_

Frigidaire

Carrier (52F series)

General Electric

/Hotpoint

Whirlpool

Fedders/Emerson

Sears/Kenmore

Emerson/Fedders

Carrier (51S Series)

Friedrich

Wall Sleeve Dimensions (inches_,

Width Height Depth

25-1/2 15-1/4 16, 17-1/2

or 22

26 15-5/8 16-7/8

17-1/8

25-7/8 16-1/2

or 23

27 16-3/4 16-3/4

or 19-3/4

25-7/8 15-17/32 16-23/32

26-3/4 15-3/4 15

25-3/4 16-7/8 18-5/8

27 16-3/4 16-3/4

NOTE: All wall sleeves used to mount the new Air

Conditioner must be in sound structural condition

and have a rear grille that securely attaches to

sleeve, or rear flange that serves as a stop for the

Air Conditioner,

[]Remove old air conditioner from existing wall

sleeve.

_1 Clean the interior of an existing sleeve.

(Do not disturb seals.)

Q Wall sleeve must be securely fastened in wall

before installing the air conditioner. Use the

nails or screws through sleeve into wall, if

needed. Repaint sleeve if needed.

!_ Prepare the wall sleeve for installation of the

unit. If you plan to use your existing wall sleeve,

and itis not Kenmore, use procedure B or C

below.

Procedure

Brand

Sears/Kenmore

White-Westinghouse

Frigidaire Carrier

(52F series)

General Electric

/Hotpoint

Whirlpool

Carrier (51S series)

Depth(inches)

16-23/32

16, 17-1/2

or 22

16-7/8

Fedders/Emerson

Emerson/Fedders

Friedrich

_r_ Install new unit intowall sleeve.

CAUTION: When installation is completed,

replacement unit MUST have a rearward slope as

shown.

17-1/8 or 23

18-5/8

16-3/4

or 19-3/4

16-3/4

UNIT Wall Sleeve

FRONT"_ 1- -_............. i

114" i _ ............. i

FIG. 3

-6-

PROCEDURE A

] If you are using the new sleeve supplied with

your unit, skip to step 3. Otherwise, install the

plastic grilla from the kit.Cut the plastic grille to

25-1/2" wide and 15-1/4" high. Place the

plastic grille to the inside ofthe wall sleeve at

the rear flange.

FIG. 4

O Fasten the 4 washer screws to secure the grille

to the wall sleeve. Ifyou need plastic nuts to

mount plastic grille to the inside of the wall

sleeve, there are plastic nuts in the installation

kit. The nuts are installed from the inside of the

sleeve and are pressed into the square holes of

the rear flanges.

FIG. 5

L_ Install the new unit into the wall sleeve.

IL_To assemble trim, snap the tab of each piece

into the slot of the other piece as shown below.

Slide trim over the front of the air conditioner

until trim is flush with sleeve as shown below.

Trim (2 ea)

Wall

FIG. 7

I_ Remove the backing from the Horizontal

Insulation strip 13/8x 3/8 X 273!16 and attach that

to the inside bottom of the sleeve as shown

below. Remove the backing from the Around

Insulation strip 1% x 3/4x 61 _2and attach that

to the inside front of the sleeve as shown

below.

FIG. 6

• Airconditionerscovered inthis manual pose

an excessive weighthazard. Two or more

people are needed to move and install the unit.

To prevent injury or strain, use proper lifting

and carrying techniques when moving unit.

• When handling the air conditioner, be careful

to avoid cuts from sharp metal fins on front and

rear coils.

• Make sure air conditioner does not fall during

removal.

-7-

PROCEDURE B

_1 Redirsct the louvers at the back of the wall

sleeve to 60° angle as shown in the FIG 8. The

use of pliers is recommended.

7 5/16"

\\\\\\\\\\\\\\\\\\\_

Rear Louve_'s

(Top View)

FIG. 8

_'_lf the wall sleeve already has a rear grille, skip

to step 4. Ifthe wall sleeve does-not have a rear

grille or Iouvered panel, install the plastic gdlle

from the kit. Cut the plastic gdlle to 25-1/2" wide

and 15-1/4" high. Place the plastic gdlle to the

inside of the wall sleeve at the rear flange.

Place the plastic grille FIG. 9

IL_I Fasten the 4 washer screws to secure the grille

to the wall sleeve. If you need plastic nuts to

mount plastic grille to the inside of the wall

steeve, there are plastic nuts in the installation

kit.The nuts are installed from the inside of the

sleeve and are pressed into the square holes of

the rear flanges.

Fasten the screws

FIG. 10

_J Remove the backing from the Horizontal

Insulation strip 13/8x % x 273/lSand attach that

to the inside bottom of the sleeve as shown

below. Remove the backing from the Around

Insulation strip 13/8x 3/4x 611/2and attach that to

the inside front of the sleeve as shown below.

FIG. 11

_-"_ Ifthe depth of your existing wall sleeve is less

than or equal to 18", skip to step 7. Otherwise,

cut the baffles and the support blocks according

to length "A" in the table below.

Depth"D"ofthe existing Length"A"

wallsleeve (inches) (inches)

18<D<_18-% 3/4

18-%<D_<19-3/4 1-3/4

19-3/4<D_<22 4

Support

Block

_]_F laffle

IG. 12

r_ Remove the backing from the support blocks

and attach them to the inside of the wall sleeve

as shown FIG 9. Slide the baffle into slots of the

support blocks.

Block

FIG. 13

_"_ Install the new unitinto the wall sleeve.

-8-

PROCEDURE B

_lTo assembletrim,snapthetabof eachpiece

intotheslotoftheotherpieceas shownbelow.

Slidetrimoverthefrontoftheair conditioner

untiltrimisflush withsleeveas shownbelow.

Trim (2 ea)

Wall

FIG. 14

• Air conditionerscoveredinthis manualpose

an excessiveweighthazard. Two or more

peopleare neededtomoveand installthe unit.

To preventinjuryorstrain,useproperlifting

and carryingtechniqueswhen movingunit.

When handlingthe air conditioner,becareful

toavoidcutsfrom sharpmetalfins on front and

rear coils.

Make sureair conditionerdoes notfall during

removal.

-9-

PROCEDURE C

il Redirect the louvers at the back ofthe wall

sleeve to 60° angle as shown in the FIG 15.

The use of pliers is recommended.

7 13116"

,\\\\\\\\\\\\\\\\\\_

Rear Louvers

(Top View)

FIG. 15

_'_lf the wall sleeve already has a rear grille, skip

to step 4. If the wall sleeve does-not have a rear

grille or Iouvered panel, install the plastic grille

from the kit. Cut the plastic grille to 26-1/2" wide

and 15-1/2" high. Place the plastic grille to the

inside of the wall sleeve at the rear flange.

Place the plastic grille

FIG. 16

I_'1 Fasten the 4 washer screws to secure the grille

to the wall sleeve. Ifyou need plastic nuts to

mount plastic grille to the inside of the wall

sleeve, there are plastic nuts in the installation

kit. The nuts are installed from the inside of the

sleeve and are pressed into the square holes of

the rear flanges.

Fasten the screws FIG. 17

L_! Remove the backing from the Horizontal

Insulation stdp 13/8x 13/ex 273j16and attach that

to the inside bottom of the sleeve as shown

below. Remove the backing from the Around

Insulation stdp 13/8x 13/8x 611/2and attach that

to the inside front ofthe sleeve as shown below.

FIG. 18

_lf the depth of your existing sleeve is less than

or equal to 18", skip to step 7. Otherwise, cut

the baffles and the support blocks according to

Length "A" in the table below.

Depth"D"of the existing Length"A"

wallsleeve (inches) (inches)

18<D<18-% 3/4

18-%<D_<19-_/4 1-3/4

19-3/4<D_<22 4

- upport

Block

_F _affle

IG. 19

r_ Remove the backing from the support blocks

and attach them to the inside ofthe wall sleeve

as shown FIG 20. Slide the baffle into slots of

the support blocks

Vail

(7 t3/16" )

Support

Block

FIG. 20

-10-

PROCEDURE C

N Remove the backing from the 13" shim strips

and attach them as shown below in Fig. 22.

The higher portion of shim is to be placed in

front of the rib on the base ofwall sleeve.

1" high_ II 3/4"High

FIG. 21

FIG. 22

_J Install the new unit into the wall sleeve

_'ITo assemble trim, snap the tab of each piece

into the slot of the other piece as shown below.

Slide trim over the front of the air conditioner

until trim is flush with sleeve as shown below.

Trim (2 ea)

Wall

FIG. 23

• Airconditioners coveredinthis manual pose

anexcessive weighthazard.Two or more

peopleare neededtomoveand installtheunit.

To preventinjuryor strain,use properlifting

andcarryingtechniqueswhenmovingunit.

• When handling theair conditioner,becareful

to avoidcutsfrom sharpmetalfins on front and

rearcoils.

• Makesure airconditionerdoes notfailduring

removal.

-11 -

HOW AND WHY

Your room air conditioner provides the following

functions to make hot weather living more

comfortable:

• Cools and circulates room air.

• Lowers humidity by removing excess moisture.

• Filters out summertime dust, dirt, and some

airborne impurities.

The air conditioner performs these functions by

drawing room air through a filter which traps dust

and dirt particles. The air then passes over a

cooling coilwhich refrigerates the air and removes

excess moisture. The same air isthen returned to

the room- cooler, drier, and cleaner. Moisture

removed from the room air is carried to the outside

and evaporated.

Your air conditioner isdesigned to be easy to

operate and to provide plenty of cooling power.

NORMAL SOUNDS FIG24

Aside from the regular fan motor and compressor

sounds coming from your air conditioner, you will

once in a while hear a pingingsound. This is the

resultof moisture being picked up from the air in the

room and thrown against the air conditioner'sfan.

This is normal and should not be cause for concern.

Also, do notbe alarmed if you hear a slight hissingor

gurgling sound coming from your air conditionerafter

it is off.These are normal coolant noises.

CAPACITY AND RUNNING TIME

Proper unitsize is important in deciding the desired

comfort for the area you want to cool. The proper

size isdetermined by the number of square feet in

the area to be cooled.

Whenever the heat or humidity load is above normal

the air conditioner must run longer and more often

to keep the desired temperature you have selected.

Under heavy heat load conditions the air conditioner

may need to run constantly to keep the temperature

you want.

At times using the MED FAN setting to circulate the

room air may make it comfortable even though you

do not have the air conditioner set to cool the air,

This will decrease your cost of use,

-Fan

- Unit Vibration

The unit may vibrate

and make noise

because of poor wall

or window

construction.

You may hear air

movement from the

fan.

The modem high

efficiencycompressor

may havea highpitched

hum orpulsatingnoise

thatcycleson andoff.

You may hear

droplets of water

hitting the condenser,

causing a pingingor

clickingsound.

FIG. 24

-12-

FEATURES

THE UNIT

1 5 736284

1. CABINET

2. HORIZONTAL AIR DEFLECTOR

(Vertical Louver)

3. VERTICAL AIR DEFLECTOR

(Horizontal Louver)

4. AIR DISCHARGE

5. FRONT GRILLE

6. INLET GRILLE (Air Intake)

7. AIR FILTER

8. VENT CONTROL

THE SLEEVE AND THE REAR GRILLE

FIG. 25

FIG, 26

USING THE AIR CONDITIONER

_To reduce the risk of fire, electric

shock, or injury to persons, read the important

SAFETY instructions section before operating this

appliance.

To begin operating the air conditioner after

installation, follow these steps:

1. Plug in the air conditioner. (To prevent electrical

hazards, do not use an extension cord or an

adapter plug.)

2. Set the TEMP control tothe coolest setting.

3. Set the MODE control at the highest COOL level

4. Adjust the louvers for comfortable air flow.

5. Once the room has cooled, adjust the TEMP and

MODE control to the setting you find most

comfortable.

NOTE : If the air conditioner is turned off, wait 3

minutes before restarting. This allows pressure

inside the compressor to equalize. Failure to wait 3

minutes before restarting may cause inefficient

operation.

If you move the TEMP control to a warmer, then

immediately back to a cooler setting, the unit will

shut off. Wait 3 minutes before restarting.

Refer to the AIR CONDITIONER FEATURES

section for other settings.

VENT CONTROL

The Vent Control allows the air conditioner to either

recirculate inside air (CLOSE) or exhaust air to the

outside (OPEN). (FIG. 27)

• The CLOSE position is used when maximum

cooling is desired. It may also be used for air

recirculation without cooling when the air

conditioner is set in the FAN position.

• The OPEN position removes stale air from the

room and exhausts itto the outside. Fresh air is

drawn intothe room through your home's normal

air passages.

• The OPEN or CLOSE position can be used with

any fan selection.

9. SLEEVE ASSEMBLY

(Including Expanded Aluminum Rear grille)

10. REAR GRILLE

(Expanded Aluminum Rear grille)

PULL OPEN / PUSH CLOSE

FIG. 27

-13-

DISPLAY

Cool •

Energy ==

Saver w

Fan •

Timer • TEMP O

C-TIMER

- SHUT-OFFTIME

• Youwillusuallyuseshut-ofttimewhileyousleep.

• Withunitrunning,useTimerto setnumberofhours

untilshut-off.

• Foryoursleepingcomfort,onceTimeisset,the

Temperaturesettingwillraise2°F after30 rain.,

and 2°F afteranother30 rain.

• EverytimeyoupushTimerbutton,itadvancesthe

Timersettingas follows:1 Hour-, 2 Hours_ """

12 Hoursmaximum.

- START TIME

•With unit not running,use Timer to set number of

hours before untilstarts.

• Every time you push Timer button, it advancesthe

Timer setting as follows: 1 Hour_ 2 Hours --,......

12 Hours maximum.

REMOTE CONTROL SIGNAL

RECEIVER

j TEMPERATURE SETTING

Usethisbuttontoautomaticaltycontrolthe

temperatureoftheroom.

Thetemperaturecanbesetwithina range

of60°Fto86°F byincrementsofI°F.

-- POWER

To turntheair conditionerON, pushthis

button.

To turntheair conditionerOFF, pushthe

buttonagain.

•Thisbuttontakespriorityoveranyother

button.

•When youfirst turn iton, the unit is in

cool mode, High fan speed, Temperature

setting at 72°F.

_-- FAN SPEED

• Everytimeyoupushthisbuttonit

advancesthesettingasfollows:

{High-' Low_ Med-, High}

MODE

- Everytimeyoupushthisbutton,itwillshiftamongCOOL, ENERGYSAVER and FAN.

- ENERGY SAVER:

• Thefan stopswhenthecompressorstopscooling.Approximatelyevery3 minutesthefan willturnonand

the unitwillchecktheroom airtodetermineifcoolingisneeded.

When power is restored after an electrical power failure, the unit will begin to run at its last setting. |

-14-

REMOTE CONTROL

NOTE: The Remote Control will not operate properly if strong lightshines on the sensor window of the Air

Conditioner or ifthere are obstacles between the Remote Control and the Air Conditioner.

Every time you push button, you will hear a beep from the Air Conditioner.

POWER

• To turnthe airconditionerON, pushthis button.Toturntheair

conditionerOFF,pushthebuttonagain.This buttontakespriorityover

any otherbutton.

Whenyoufirstturn iton,the unitisin coolmode,Highfan speed,

Temperaturesettingat 72°F.

TEMPERATURE SETrlNG

• Usethisbuttontoautomaticallycontrolthetemperatureofthe room.

Thetemperaturecanbe setwithina rangeof60°Fto86°Fby

incrementsof I°F.

FAN SPEED

• Everytime you push this button it advances the setting as follows:

(High ." Low * Med _High)

TIMER

- SHUT-OFF TIME

• You will usually use shut-off time while you sleep.

• With unit running, use Timer to set number of hours until shut-off.

• For your sleeping comfort, once Time is set, the Temperature setting will

raise 2°F after 30 min, and after another 30 min.

• Every time you push Timer button, it advances the Timer setting as follows:

1 Hour , 2 Hours ...... .- 12 Hours maximum.

- START TIME

• With unit not running, use Timer to setnumber of hours before until start.

• Every time you push Timer button, it advances the Timer setting as follows:

1 Hour *2 Hours , ..... ÷ 12Hoursmaximum.

MODE

- Every time you push this button, it will shift among COOL, ENERGY SAVER and FAN.

- ENERGY SAVER

• The fan stops when the compressor stops cooling.

Approximately every 3 minutes the fan will turn on and the unit will check the room air to determine if cooling is

needed.

-15-

INSERTING THE REMOTE CONTROL

BA'n'ERIES

1. Remove the cover from the back of the remote

controller.

2. Insert two batteries.

• Be sure that the (+) and (-) directions are

correct.

• Be sure that both batteries are new.

3. Reattach cover.

FIG. 28

• In order to prevent discharge, remove the batteries

from the remote control if the air conditioner is not

going to be used for an extended period of time

Keep the remote control away from extremely hot

or humid places.

To maintain optimal operation of the remote

control, the remote sensor should not be exposed

to direct sunlight.

• The remote control can be mounted on a wall

using the mountable holder.

FIG. 29

HORIZONTAL AIR-DIRECTION

ADJUSTMENT

• The hodzontal air direction is adjusted by moving

vertical louver.

• The vertical louver control levers are located in the

right and left side of the air discharge.

FIG. 30

VERTICAL AIR-DIRECTION ADJUSTMENT

• The vertical air direction is adjusted by moving the

horizontal louvers.

FIG. 31

-16-

AIR FILTER CLEANING

The Air Filter will become dirty as it removes dust

from the inside air. it should be washed at least

every 2 weeks. If the Air Filter remains full of dust,

the air flow will decrease and the cooling capacity

will be reduced, possiblydamaging the unit.

• Pull the inlet grille forward and pull out the air filter.

(FIG. 32)

• Wash the Air Filter under the faucet with warm

water. Be sure to shake off all the water before

replacing the filter. (FIG. 33)

FIG. 32 FIG. 33

AIR CONDITIONER CLEANING

Clean the front grille and inlet grille by wiping with a

cloth dampened in a mild detergent solution.

The cabinet may be washed with mild soap or

detergent and lukewarm water, then polished with

liquid appliance wax.

To ensure continued peak efficiency, the condenser

coils (outdoor side of the unit) should be checked

pedodically and cleaned if they become clogged

with soot or dirt from the atmosphere. Brush or

vacuum exterior coils to remove debris from fins.

FIG. 34

HOW TO REMOVE THE FRONT

GRILLE

• Open the inlet gdlle.

• Remove the screw securing the Front Grille.

• Push the grille up from the bottom and pull the top

ofthe grille away from the case to lift the top tabs

out oftheir slots.

FIG. 35

HOW TO REPLACE THE

FRONT GRILLE

Attach the front grille to the cabinet by inserting the

tabs on the grille into the slots on the front of the

cabinet. Push the grille in until it snaps into place.

FIG. 36

-17-

BEFORE CALLING FOR SERVICE

Check the following listto be sure a service call is really necessary. A quick reference to this manual may

help you avoid an unneeded service call.

THE AIR CONDITIONER WILL NOT OPERATE

Check if... Then...

Wallplugdisconnected.

Housetuseblownorcircuitbreakertripped.

PowerisOFF.

Unitwastumedoffandthenontooquickly.

TEMPControlsetwarmerthanroomtemperature.

Pushplugfirmlyintowailoutlet.

Replacefusewithfimedelaytypeor reset¢irouilbreaker.

Pushthepowerbutton.

Setunitoffandwait3minutesbeforerestarting.

SetTEMPControltoa lowernumber,

AIR FROM UNIT DOES NOT FEEL COLD ENOUGH.

Check if... Then...

FANSPEEDsetat LOW.

TEMPControls_ toowarm.

Roomtemperaturebelc_v70°F(21°C).

Temperaturesensingtubetouchingevaporatorcoil,

locatedbehindfrontgrille.

PushFANSPEEDbuttontosetatHI.

SetTEMPControltoa lowertemperature

Coolingmaynotoccuruntilroomtemperaturerisesabove70°F(21°C).

StraightentubeawayfTomevaporatorcoil.

THEAIRCONDmONERCOOUNG,BUTROOMISTOOWARM- ICEFORMINGONCOOLINGCOILBEHINDINLETGRILLE.

Check if... Then...

Outdoortemperaturebelow70°F(21°C). Todefrostthecoil,settheMODEtoFAN,FANspeedtoHigh.

Airfiltermaybedirty. Cleanairfilter.RefertoMaintenancesectionofowner'smanual.

Todefrostthecoil,settheMODEtoCool,Fanspeedtohigh,andthe

TEMPControlsettoolow. Tempcont_ toahighertemperature.

THEAIRCONDITIONERC00UNG,BUTROOMISTOOWARM

Check if...

Dirtyairfilter- airrestricted.

TEMPControlsettoowarm.

Frontofunitisblockedbydrapes,blinds,furniture,etc.

Airdistributionisrestricted.

Doors,windows,recjisters,etc.open.Coldairescapes,

Unitrecentlyturnedoninhotroom.

Then...

Cleanairfilter.RefertoMaintenancesectionofowner'smanual.

SetTEMPControltoa lowertemperature

Clearbionkageinfrontof unit,

Close doors, windows, reg_ers, etc.

Allowadditional_mete removestoredheatfromwails,ceiling,floor,andfuture

THE AIR CONDITIONER TURNS ON AND OFF RAPIDLY.

Check if... Then...

Outsidetemperatureisextremelyhot. ISetFANSPEEDonHItobringair coolingcoilsfaster. I

past

NOISE WHEN UNIT IS COOLING.

Check if... Then...

Soeadoffanhitfingwater- fromthemoistureremovalsystem. Thislsnormalwhenhumidityishigh.Closedoors,windows,aedragistera.

Windowvibration- poor nstalaton. Referto nstsiafionnstruclfensorcheckwithnsta er.

WATER DRIPPING INSIDE ROOM WHEN UNIT IS COOLING.

Check if... Then...

I Theairconditionerisirnproperiyinstalled. I Tiltaircondifionerslighltytotheoutsidetoallowwaterdrathage.Referto

nstaaton nstrestionsorsheckwth nsta er.

WATER DRIPPING OUTSIDE WHEN UNIT IS COOLING.

Check if... Then...

Theunitisremovinglargequantitiesofmoisture

fromhumidroom I Thislsn°rmaldudngexceeaivelyhumiddays I

-18-

-19-

|NDICE ...................................................... 20

GARANT|A .............................................. 20

SEGURIDAD ........................................... 21

Instruccionesimportantesde seguridad ...21

REQUISITOS ELECTRICOS ............. 22

INSTALACI(_N ........................................ 23

Requisitos de instalacibn ....................... 23

Instalacibn .............................................. 24

Procedimiento A..................................... 25

Procedimiento B..................................... 26

Procedimiento C..................................... 28

FUNClONAMIENTO ............................. 3O

C6mo y pot qu_...................................... 30

Sonidos normales .................................. 30

Capacidad y tiempode funcionamiento--..30

Caracterfsticas ....................................... 31

Uso del aparato de aire acondicionado.---.31

Caracterfsticas del aparato de aire

acondicionado ........................................ 32

MANTENIMIENTO ................................ 35

Limpieza del filtro de aire ....................... 35

Limpieza del aparato de aire

acondicionado........................................ 35

Cbmo extraer la rejilla frontal ................. 35

Cbmo volver a colocar la rejillafrontal ...35

RESOLUCI(SN DE PROBLEMAS-...36

Antes de Ilamar al servicio t_cnico .........36

ACUERDOS DE PROTECCION

ESPECIALIZADA ..................................39

NUMEROS DE SERVIClO

TF:CNICO .................................. Contraportada

GARANTiACOMPLETADE UNAI_ODEL

APARATODEAIRE ACONDICIONADODE

PARED

DuranteunaSo,a contarapartirdela fechadecompra,cuando

esteaparatodeaireacondic_onadofuncioneparaelenfriamiento

normaldeunahabitacibnyrecibamantenimiento,todoello

segenlasinstruccioaesdeesteManualdelpmpietaFio,Sears

reparar_esteaparatodeaireacondicionado,deformagratuita,si

tuvieraalgundefectodefabricaci6nomateriales.

GARANTfACOMPLETADE CINCOANOSDEL

SISTEMASELLADODE REFRIGERAClON

Durantecincoafiosa contara partirdelafechadecompra,

cuandoesteaparatode aireacondicionadofuncioneparael

enfriamientonormaldeunahabitaci6ny recibamantenimiento,

todoelloseg0nlasinstruccionesdeesteManualdelpropietado,

Searsredarar_iel sistemaselladoderefrigeraci6n(queconsiste

en Ifquidoderefrigeraci6n,tubosdeconexi6nycompresor),de

formagratuita,situvieraalg_ndefectodefabricaci6no

materiales.

ELSERVICIODEGARANTIAPUEDE

CONTACTARSEENELSERVIClODEATENCI()N

AL CLIENTEDESEARS ENEL1-800-4-MY-HOME®.

Lacoberturadeestagarantiaseapricasolamenteaaparatosde

aireacondicionadoutilizedosdeformano comercial,encasas

particulares,

Estagarantiaseaplicas61oduranteelusodeesteproductoen

losEstadosUnidos.

Estagarantfaleconcedederechoslegalesespecificosy puede

queustedtengaotrosderechosadicionalesquevarianseg_nel

estado.

Sears,RoebuckandCo., D/817WA,Hoffman

Estates,IL60179 EE. UU.

- 20 -

INSTRUCClONES IMPORTANTES DE SEGURIDAD

Las instrucciones de seguridad que se indican abajo le dirdn cbmo utilizar su aparato de aire acondicionado

para evitar dahos a sf mismo y dafios a su APARATO DE AIRE ACONDICIONADO.

PARASU SEGURIDAD

No almacene ni utilicegasolina ni otros liquidos ni gases

inflamablescerca de _ste u otro electrodomestico. Lea

las etiquetasde los productos para conocer su

inflamabilidad y otras advertencias.

_ EVITAR ACCIDENTES

Parareducirel desgode incendio,electrocuci6no heridasa

personasal utilizersoaparatode aireacondieionado,siga

lasprecaucionesbasicas,incluyendolassiguientes:

• Asegl]resedequeelservicioelectricoes adecuadoparael

modeloqueha escogido.

• Siel aireaeondicionadovaa instalarseerruna ventana,

seriaconvenienteque limpiaraprimeroambos ladosdel

crista[ Si laventanatieneires guias de deslizamiento,con

unpanelpantallaincluido,puedequedeseeextraer

completamentelapantallaantesde la instalaci6n.

• Aseguresedeque el aparatode aireacondicionadose ha

instaladode modoseguroy correctoseg6nlas

instruccioneseneste Manual.Guardeeste manualy las

instruccionesde instalacionparasu posible usofuturepara

extraero volvera instalaresta unidad.

• Utiliceguantescoando manejeelaparatodeaire

acondieionado.Presteatenci6nparaevitarcortesde las

afiladasaletasde metalenlas bobinasfrontaly posterior.

INFORMACION EL_:CTRICA

Elvalornominalel_ctricocompletedesunuevoeparatodeaire

asondicionadoseespeeificaensu etiquetaidentificativa.

Consulteel valornominalal somprobarlosrequisitesel_tricos.

• Asegi]resedeque el aparatode aireacondicionadotiene

unatomede tierraadecoada.Parareduciral minimoel

riesgode electrocucibny deincendio,es importantetenet

unatomadetierra adecoada.El cablede abmentaci6nesta

equipadoconun enchafedetresclavijascon tomaatierra

pareprotegercontraelectrocuci6n.

• Suaparatode aireacondicionadodebe estarenchufadoa

unenchufede paredcon unatomade tierra adeeuada.Si

el enchufe quequiere utilizarnotiene una tomadetierra

adecuadaono estaprotegidopot un fusibletempofizadoo

uninterruptordecorriente,hagaqueun electricista

cualificadoinstaleel enchufeapropiado.

• Nohagafuncionarel aparatode aireacondicionadocon la

laminadeembalajeen la parleposteriordel alojamientoo

con lacintaazul y las esquinerasdelaparatode aire

acondicionado.Estopodriatenercomeconsecuenciala

producci6nde dafiosmecanicosal aparatode aire

acondicionado.

• Noutilice uncableextensorni un enchufeadaptador.

_ Evitelospeligrosdeincendioodeelectrocuc_.

Noutilicauncableextensoreiunenchufeadaptador.

Noquiteningunaclaviiadelcabledealimentacion.

Recept_culoen

paredcontoma Nunca code, extraiga ni]

de tierra haga unadedvacibn que /

evite la clavijadetoma ]

de tierrade este /

enohufe. J

j.,

CoCna:lnec_uefea'_lee_l civbijnas_1 k

con toma de tierra

IDEAS PARAAHORRAR ENERG[A

• La capacidaddelaparato de aireacondicionadodebe

ser adecuada al tamafio de la habitaci6npara un

funcionamiento eficaz y satisfactorio.

• Instaleel aparato de aire acondicionado en el lado de su

hogarala sombra. Unaventana que mira al notre es la

mejor porque seencuentraala sombre la mayor parte

delalia.

• Nobloquee el flujo del aimen el interior con persianas,

cortioaso muebles,nien elexteriorconarbustos,

cercasu otrosediflcios.

• Cierre las aperturas en sueloy ventanasy el tiro de la

chimenea para que el airefifo no salga pot la chimenea

ni por los conductos.

• Mantengacerradas laspersianas y cortinas de otras

ventaeas durante la parte rods soleada del dia.

• Limpieel filtro de aire segl_nse recomieodaen la

secci6n de MANTENIMIENTOde este manual.

• El aislamientoadecuado y la preparaci6n de su hogar

para lascondiciones atmosf_dcas mantendr_inel aire

caliente en el exterior y el aire frio en el interior.

• Laexistencia de sombra en el exterior de lacasa con

_irboles,plantas otoldos reduce la carga de trabajo del

aparato deaire acondicionado.

• Haga fuocionar los electrodom_sticos que produzcan

calor, come cocinas, lavadoras, secadoras y lavavajillas,

durante lapartemas fr/a del dia.

-21 -

CLIMPLA TODAS LAS NORMAS Y C6DIGOS

LOCALES

NUNCA ELIMINE LA CLAVIJA DE TOMA DE

TIERRA DEL CABLE DE ALIMENTACI(_N.

LA TOMA DE TIERRA ELECTRICA EN ESTE

ELECTRODOMI_STICO ES NECESARIA.

Se necesita una alimentacibn el_ctrica de

208/230-volt 60 Hz, s61ode CA, con fusible de

15A y con una toma de tierra adecuada. Se

recomienda tambien que haya un fusible o

interruptor temporizado. Utilice un circuito

el_ctrico dedicado s61o a este aparato.

NO UTILICE UN CABLE EXTENSOR.

METODO RECOMENDADO DE TOMA DE

TIERRA

Para su seguridad personal, este aparato debe

tener una toma de tierra. Este aparato tiene un

cable de alimentaci6n con un enchufe de 3

clavijas, una de elias para la toma de tierra.

Para reducir al mfnimo el riesgo de

electrocuci6n, el cable debe estar enchufado

en un recept&culo de pared con toma de tierra

de acuerdo con la t_ltimaedici6n del C6digo

nacional sobre electdcidad (ANSI/NFPA 70) y

siguiendo todas tas normas y directrices

locales. Si no est& disponible un recept_.culo

de pared, es responsabilidad y obligaci6n

personal del cliente hacer que un electricista

cualificado instale un recept&culo en la pared

de 3 clavijas con una toma de tierra adecuada.

Riesgo de electrocuci6n

Enchufe en una toma de 3 clavijas con toma

de tierra. No elimine la clavija de toma de

tierra. No utilice un adaptador.

No utilice un cable extensor.

No seguir estas instrucciones puede tener

como consecuencia la muerte, un incendio o

electrocuci6n.

Cable de --

alimentaci6n con

clavija dotada de

conexi6n a tierra _

de 3 terminates. ] _

Toma de corriente ]_ "_

de pared con ]_ _,_

cenexi6n a tJerra" !i__Ter

I conexibn a tierra.

Bajo ninguna

circunstancia corte, quite o

evite el uso de la conexibn

a tierra de esta clavija.

- 22 -

Extraigala Ibmina deembatajedel alojarnientodel

aparatode aim acondicionadoy laesquineraycintaazul

delaparato de aireacondicionado.

REQUlSITOS DE INSTALAClON

Siutilizaunalojamientode paredexistente,dedetomarsus

rnedidas.

Instaleelnuevoaparatodeaireacondicionedosegenestas

instruccionesdeinstalaci6nparaconseguirelmejorreedimiento.

Tedoslosalojarnientosdeparedutilizedosparamontarel nuevo

aparatodeaireacoedieionadodebentenersu estructuraen

buenascondicionesytenerunarejillaposteriorparafijarcon

seguridadelnuevoaparatodeaireacondicionade.(FIG.l)

ConelalojarnientoKenmore,puedemantenerelm_irno

reedimientodesunuevoaparatode aireacondicionado.(FIG.2)

Aparatodeaireacondidonado

18"(458rnrn)

FIG. 1

EQUIPO DE INSTALACI6N

/_CULC NOMBREDE!.ASPIEZAS ._ITIOAD

(_ REJILLA DE PLASTICO 1

(_ TIRAS DE AISLAMIENTO HORIZONTAL 2

(_) TIRAS DE AISLAMIENTO LATERAL 2

(_ BLOQUE DE SOPORTE 2

_(_ DEFLECTOR 1

(_ BASTIDOR DE REBORDE 2

(Z) CALZO PARA AJUSTE 2

(_) TUERCASDEPLASTICOYTORNILLOSDEARANDELA4

2S.T/a"

(656 ram)

=_/32"

. (425turn)

AlojamientodeparedKenmore FIG.2

SERVICIO ELECTRICO

Compruebeelservicioel_ctricodisponible.Laalimentaci6n

disponibledebecoineidirconlaquesemuestraenlaetiqueta

identificativadelaunided(quesoencuentraenelladeizquierde

delalojarniento).

Tedoslosmedelosestaneduipadosconunenchuf9deservicio

de3 clavijasconunatomadetierrapositivasegura.No

medifiqueelenchufedeningunarnaneraNoutiliceunenchufe

edaptador.Sisutomadecorrienteenlaparednocoincideconel

enchufe,llamaaunelectricistacualificadoparareWizarlos

cambiosnecesarios.GUARDELACAJAparaelalrnacenamiento

yestaGUiADELPROPIETARIOparafuturareferencia,Lacaja

9sla mejormaneradealmacenarla unidadduranteelinviernoo

cuandonoseutidee.

Paraevitarpeligrodeheridaspersonales,da6osalapropiedado

alproductodebidoalpesodeesfeaparatoyalosbordes

afiladosquepuedenestarexpuestos:

• Losaparatosdeaireacondloionadodelosquetrataeste

manualconstituyenunpeligrodepesoexcesivo.Senecesitan

dosom&spersonasparamovereinstalarlaunidad.Paraevitar

heridasoproblemasmuscolares,utilicet6cnicasadecuadas

paraelevarydesplazarlaunidad.

, RevisecuidadosamentelaubicaciSndondeseinstalar_elaparato

deaimacondiclonado.AsegL]resedequepuedesoportarelpeso

delaunidadduranteunpededodetiempoprolongado.

, Manejeconcuidadoelaparatodeaireacondicionado.Ueve

guantesprotectoressiemprequelevanteodesplaoelaunidad.

EVITElasalotasafiladasdemetaldelasbobinasfrontaly

posterior.

°AsegSresedequeelaparatodeaireacondiclonadonocaeal

suelodurantelainstalaci6n.

HERRAMIENTASNECESARIAS:

, Guantesa)ustados

• Destornittadorestandar

, DestomilladorPhillips

•CuchJlloafJlado

•Cintaparamedir

. Llaveajustableodeextremo I

abiertode0,96cm(328deputgade)

• Uavearticulada

, Llavedecabe_hexagonalde

0,64cm(1/4depulgada)y

tdnquete

•Taladroetdetrico

, Brocadetaladrode0,64crn

(t/4depu_gada)

- 23 -

INSTALACION

Serecomiendeencarecidementelaextracci6ndel

antiguoalojamientoenlaparedylainstalaci6ndeun

nuevoalojamientodeparedKENMORE.

Sidecidemantenerelalejamientodeparedexistente,

tendr_queajustarladirecci6ndelarejillaenlapar_e

posteriordelailustraci6ndelalojamientodepared.Se

recomiendaelusedetenazas.SiNOajustaladireccidn,

correeldesgodeunrendimientopobreo defallodel

producto.Estehechonoestacubiertobajolostdrminosde

lagarantiadeKENMORE.

• Sidecidemantenerelalojamientodeparedexistente,tendr&

queajostarladireccidndelarejillaenlaparteposteriordela

ilustracidndelalojamientodepared.Serecomiondaelusode

tenazas.SiNOajustaladireccidn,correelriesgodeun

rendimientopobreodefallodelpreducto.Estehechonoesta

cubiertobajolosterminosdelagamnt[adeKENMORE

ART{CULOSEN EL EQUIPODE INSTALACI(_N

Puedequenonecesitetodaslaspartesdelequipode

insta]aeidn.Tirelaspiezasquenoutilice.

ART{CULO

Rejifladepl&stico

Tirasdeaislamientohorizontal

Tirasdeaislamientolateral

Bl_Jedese_de

Deflector 1

Calzoparaajuste 2

Banderdereborde 2

Tomilbdearandela 4

Tuercas(plasf_o) 4

C! NO INSTALARLO

D IdentiSqueel alojamientoexistenteenlaparedantesde

instalarlaunidaddelalistaquesemuestraa continuacidn

Can_

3,8!x2,54x210,03cm(263hx16V2) 1

3,5x1,52x69,03crn(131Bx%x2"Ph_)1

3,5x3,5x69,03crn(13/ex1z/8x27_h6) !

3,Sx2,03x153,035(131sx3kx61V2) 1

3,Sx3,5x153,035(13/ax Plsx61Y2) 1

8,89X3,5x10,94¢zll(P/4XPieX4sJ_6) 2

35,56x11,43x0,33(14x4V_xYe)

33,02x2,54x2,03(13x1X_/_)

Marca

White-Westinghouse

Frigidaire

Carrier(Serie52F)

GeneralElectda/Hotpoint

Whirlpool

Fedders!Emerson

Sears/Kenmore

EmersonJFedders

Carrier(Sede51S)

i Friedrich

Medidasdelalojamientoderapared

(pulgadasy centfmetros)

Anchura Altura Profundidad

64,77 38,73 _,64,44,45,55,88

(25-1/2) (15-1/4) (16,17-1/2)

66,04(26) 39,70(15-5/8142,87(16-7/8)

65,48(25-7/8)41,91(16-1/2'43,51o58,42

(17-1/8o23)

42,54o50,16

68,58(27) 42,54(16-3/41(16-3/4o19-3/4)

65,73(25-7/8)39,44(15-17/32142,46(16-23/32)

67,94(26,3/4)40(15-3/4) 38,1(15)

65,40(25-3/4) 42,87(16-7/8) 47,32(18-5/8)

68,58(27) 42,54(16-3/4142,54(t6-3/4)

NOTA:Tedoslosalojamientosdeparedutilizadosparamontar

el nuevoaparatodeaireacondicionedodebenestarenbuenas

eondicionesestrusturalesytenerunarejillaposteriorqueseuna

conseguddadalalojamientoounflanooposteriorcluesirvade

topealaparatodeaireacondicionado,

_ Extraigaelantiguoaparatodeaireacondicionadodel

alojamientodeparedyaexistente.

_1 IJmpieelinteriordelalojamientodeparedyaexistente.

(Notoquelosselledos.)

L_EI alojamientodepareddebeestarbienfijedoalapared

antesdeinstalarelaparatodeaireasendicionedo.Sifuera

necesario,utilicelosclavosotomillosparafijarel

aiojamientoa _ pared.

•Vuelvaapintarelaiojamientosifueranecesario.

_"t Prepareela_amientodepa_ paralainelalack_delaunidad.Si

piensautilizarelalojamientoyaex_ente,ynoesdelamarcaKenmore,

utilicelospr_edimientosBoCqueseexplicanacontinuacidn.

ProcedimientoMarca

A Sears/Kenmore

White-Westinghouse

FrigidaireCarrier

52Fseries)

B GeneralElectnc

/Hotpoint

Whirlpool

Carrier(51Sseries)

Fedders]Emerson

C EmersoNFedders

Friedrich

Profundidad

42,44(16-23/32)

40,64,44,450 55,88

(16,17-1/2o22)

42,87(16-7/8)

43,5O58,42(17-1/80 23)

47,29(18-5/8)

42,54050,16(16-3/4019-314)

38,1(15)

42,54(16-3/4)

ret Instalelanuevaunidadenel alojamientodelapared.

CUIDADO:Cuandolaiostalacidnestecompleta,Januevaunidad

DEBEtenerunaieclinacidnhaciaatr_issegdnsemuestraenla

ilustracion.

Alojamiento

PARTE _._i _1-;-A-_"----d-_1"_!_:red

FRONTIL.Ill,(ll

0,635 cm(1/4)

FIG. 3

- 24 -

PROCEDIMIENTO A

_lSi est_utilizandoel nuevoalojamientoque asompariaa

suunidad,pase directamentealpaso 3.Encaso

contrario,instalela rejillapl_sticadelequipo.Cortela

rejillade pldsticoa 64,77cm(25-1/2)deanchoy 38,74

cm (15-1/4)de alto.Coloquela rejillade plasticoen el

interiordelalojamientode pared,en elflansoposterior.

L_lj Instalelanuevaunidadenelalojamientode lapared.

_J_ Para montar elreborde, inserteelsalientede cada

pieza en la ranura de la otrapiezaseg_n se muestra

abajo. Deslice el reborde sobre laparte frontal de1

aparato de aireacondicionado hastaque el reborde

est6 unido a pario con elalojamiento seg_n se

muestra acontinuaci6n.

FIG. 4

F_ Apriete los 4 tomillos de arandelapara fijar la rejilla

al alojamiento de pared. Si necesitatuercas de

pl&sticopara montar la rejillade pl_.sticoen el interior

del alojamianto, hay tuercasde pl&sticoen el equipo

de instalacibn. Las tuercasse instalan desde el

interior de1alojamiento y se introducen apret&ndolas

en los orificios euadrados de losflancoa traseros.

FIG. 5

_J Extraiga la parte posterior de latira de Aislamiente

horizontal de 3,5 x 0,96 x 69,06 cm (13/8x 3/sx

273/lo)y fijela a la parte inferior intema del

alojamiento segSnse muestra abajo. Extraiga la

parte posterior de latira de Aislamiento lateralde 3,5

x 1,9 x 156,21cm (1_/Bx 3/4x 611/2)y fijela al intedor

del alojamiento segOnse muestra abajo.

FIG. 6

Adorno (2ea)

Pared

FIG. 7

•Losaparatosdeaimacondieionadodelosquetrata

estemanualconstituyenunpeligrodepesoexcesivo.

Senecesitandosom_spersonasparamovere

instalarla unidad.Paraevitarheridase problemas

musculares,utilicet_cnicasadecuadasparaelevary

desplazarlaunidad.

• AImanejarel aparatodeaireacondicionado,tenga

cuidadodeevitarcortesdelasaletasafiladasde metal

en lasbobinasfrontalytrasera.

•Asegt_resedequeelaparatodeaireacondicionadono

secaedurantelainstalaci6n.

- 25 -

PROCEDIMIENTO B

_11 Coloquela direcci6ndela rejillaen taparteposteriordel

alojamientodela paredenun _ingulode 60° segOnse

muestraen laFIG 8.Se recomiendael usodetenaTas.

19,84 cm(7 Slls")

Rejilla posterior

(Vista superior)

FIG. 8

I_11 Sielalojamientode paredestaya equipadoconuna

rejillatrasera,pase directamenteal paso4. Si el

alojamientode la parednotiene una rejillaposteriorni

anpanelconlamas,instalelarejillade pl_isticodel

equipode instalacipa.Cortela rejillade plastieoa unas

medidasde 64,77cm(25-1/2)deanchoy 38,74cm

(15-1/4)de alto.Coloquela rejillade plasticoen el

interiordel aloiamientode pareden el flancoposterior.

Coloque la rejilla de pl_.stico FIG. 9

IL_I Cuando el alojamiento de la paredtiene una rejilla

posterior de panel con lamas, salte alpaso3 y omita

el paso 4. Coloque la rejilla de pl_stico en elinterior

del alojamiento de pared en el flancoposterior.

Apriete los tornillos

FIG. l(

Q ExtraigalaparteposteriordelaliradeAislamiento

horizontalde3,5x1,60x 69,06cm(13/Bxs/8x 273h6)yfijela

alaparteinferiorintemadelalolamientosegunsemuestra

abajo.ExtraigalaparteposteriordelatiradeAislamiento

lateralde3,5x 1,9x156,21(13/8x 3/4x61V2)yfijelaal

interiordelalojamientosegt_nsemuestraabajo.

FIG. 11

IL_I Cuando la profundidad del alojamientoexistente es

igual oreenor a 45,72 cm (18 pulgadas), pase

directamente al paso7. Encaso contrario, corte los

deflectores y los bloques de soporte segQnla

Iongitud"A" de latabla quese muestra abajo.

Pr0fundidad"D"delalojamientoLongitud"A"

Jeparedyaexistente(pulgadasl(pulgadas)

18 <D_<18-5/8 3/4

18-% <D<19"3/4 1-3/4

19-3/4<[3_<22 4

A _ Bloque

de sopane

ir_ Extraiga la parte posterior de losbloques de soporte

y fijelos en el interiordel alojaraiento de la pared

segun se muestra en la FIG 9. Desliee el deflector en

las ranuras de los bloques de soporte.

Pared

Alojamiento

depared

• (7 5/16"

__ -- Blpaue

desopone

FIG. 13

_'-_ Instalelanuevaunidaden elalojamientode la pared

- 26-

PROCEDIMIENTOB

Q Paramontarel reborde,inserteelsalientede cada

piezaen la ranurade laotrapiezasegunsemuestra

abajo.Desticeel rebordesobrelapartefrontaldel

aparatodeaimacondicionadohastaque elreborde

esteunidoa pasoconel alojamientosegt_nsemuestra

a continuaci6n.

Adorno (2ea)"_._

Pared

FIG. 10

• Losaparatosdeaire acondicionadodelosque

trata estemanualconstituyenunpeligrode peso

excesivo.Se necesitandoso m&spersonaspara

movere instalarla unidad.Para evitarheridaso

problemasmusculares,utilicet_cnicasadecuadas

paraelevary desplazarla unidad.

• AImanejarelaparatode aireacondicionado,tenga

cuidadodeevitarcortesdelasaletasafUadasde

metalenlas bobinasfrontaly trasera.

•Aseg_resede que el aparatode aire

acondicionadonocae al suelodurantela

instalaci6n.

- 27 -

PROCEDIMIENTO C

_1 Coloquela direcci6ndelarejillaenla parteposteriordel

aiojamientodela paredenun_ngulode 60°seg_nse

muestraenla FIG15.Serecomiondael usodetenazas.

6o_

19,84 cm(7 13/16")

\,\,,,\\,\\\,\,,\,,_/_ O°

Rejilla posterior

(Vista superior)

FIG. 15

_'_Si elalojamiento de la pared notiene unarejilla

posterior o un panelcon lamas, instale la rejillade

pl_stico del equipo de instalaci6n. Corte la rejilla de

plastico a unas medidas de 67,31 cm (26-1/2) de

anchoy 39,37 cm (15-1/2) de alto.

Coloque la rejilla de pldstico

FIG. 16

_1 Cuando la profundidad del alojamiento existente es

igualo menor a 45,72 cm (18 pulgadas), pase

directamente a]paso 7. Corte los deflectores y los

bloques de soportesegL_nla Iongitud "A" de la tabla

quese muestra abajo.

FIG. 17

_J_ Extraigalaparteposteriorde latirade Aislamiento

horizontalde 3,5x 3,5 x 69,06cm(13/8x 13/8x

273/16)y fijelaa lapade inferiorintemadelalojamiento

segdnsemuestraabajo. Extraigalapartep_tedor de

la tira deAislamientolateralde 3,5x 3,5 x 156,21cm

(13/8x 13/8x 611/2)y fijela al interiorfron_ del

alojarnientosegdnsemuestraabajo.

FIG. 18

_"_ Cuando la profundidad del alojamiento existente es

igual o menor a45,72 cm (18pulgadas), pase

directamente al paso 7. De otra manera,corte los

desviadoresy los bloques del soporte de acuerdo a

la Iongitud "A" en el cuadro siguiente.

Profundidad"D"deial0jamientoLongitud"A"

'leparedyaexistente(pulgadasl(pulgadas)

18<D_<18-5/8 3/4

18-5/8<D<_19-_/4 1_a/,

19-3/4<D_<22 4

-- Bloque

desoporle

1_ Deflector

_., FIG. 19

r_ Extraigalaparteposteriordelosbloquesdesoportey

fijelosal interiordelalojamientodela paredseg_nse

rnuestraenla FIG20.Desliceeldeflectoreelas ranurasde

losbloquesdesoporte.

, (713_,6')

Pared

Alojamiento '_

delapared

81oque

desoporte

FIG. 20

- 28 -

PROCEDIMIENTO C

_1 Extraigaelrefuerzode lastirasde reborde33,02(13)y

fi]elassegt]nsemuestraabajoen laFIG22. Laparte

supedordelrebordedebecolocarseenfrentedel

rebordeen labasedelalojamientodela pared.

IEI Para montarelreborde,inserteel salientedecada

piezaen laranurade laotrapiezaseg0nsemuestra

abajo.Desliceelrebordesobrelaparlefrontaldel

aparatode aireacondicionadohastaque elmborde

est6unidoa pasoconelalojamientosegOnse muestm

a continuaci6n.

1"High]I--1 II 3/4"High

FIG. 21

FIG. 22

I_ Instale la nueva unidad en el alojamiento de la

pared.

Adomo (2ea)

Pared

FIG. 23

• Losaparatosdeaireacondicionadode losque

trataeste manualconstituyenunpeligrode peso

excesivo.Senecesitandoso m_spersonaspara

movere instalartaunidad.Paraevitarheridaso

problemasmusculares,utilicet6cnicasadecuadas

paraelevarydesplazarla unidad.

•AImanejarel aparatode aireacondicionado,tenga

cuidadode evitarcortesde 1asaletasafiladasde

metalen lasbobinasfrontalytrasera.

•AsegSresede queel aparatode airs

acondicionadonocaeal suelodurantela

instalacion.

- 29 -

COMO Y PORQUE

Esteaireacondicionadoincluyeunmanualde instrucciones

parahacerrndsagradableslascondicionesde habitabilidad

enestacionescalurosas.

• Refrigeray hacecircularelairede lahabitaci6n.

• Eliminalahumedadenexceso.

• Losfiltroseliminanel polvoy lasuciedadtipicasde la

estaci6n,asf comolas impurezasque elaire contiene.

El aireacondicionadorealizalasfuncionesanterioresal

hacerpasarel airede lahabitaci6natray,s de un filtroque

atrapalas particulasde polvoy la suciedad.A continuaci6n,

el aire pasa porunserpentfn derefrigeraci6nque enfriael

airey eliminala humedadenexceso.El mismoairevolveraa

la habitaci6nperomasfrfo, m_.ssecoy maslimpio.La

humedadque se haeliminadodelaire de la habitaci6nsale

al exteriory seevapora.

Esteaireacondicionadose hadisefiadoparaque seafacil

deutilizar y paraque proporcionela maximacapacidadde

refrigeraci6n.

SONIDOS NORMALESFIG.24

Ademasde los sonidosnormalesdelcompresory del motor

delventiladorque procedendel aire acondicionado,es

posiblequeoiga devezen cuandounsonidode silbidos.

Estosedebealsonidoque se produceai recogerla

humedaddel aire dela habitaci6ny expulsarlaatravesdel

ventiladordelaire acondicionado.Estesonidoes normal,no

tieneporqu6preocuparse.Tambien es posiblequese

escucheun sonidode siseoode borboteocuandoapagueel

aireacondicionado.Nodebealarmarse,ya que sonsonido

normalesque se producenal refrigerar.

- Ventilador

-Vibtaciones

Esposiblequela unidadvibrey

emitaruidosdebidoa la

construcciSndeficientedelas

paredesode lasventanas.

Esposiblequeoigael

movimientodelventilador.

-Compresor

Esposibleque el modemo

compresorde alto

rendimientolancehumoo

emitaruidosdeforma

intermitente.

Tambienesposibleque

oiga gotasdeaguacaer

enel condensadordando

lugara silbidosoclics.

FIG. 24

CAPACIDADY TIEMPO DE

FUNCIONAMIENTO

Esimportanteestablecerlazonaquedesearefrigerarpara

decidirenconsecuenciaeltamafio adecuadode la unidad.

Su tamafiodepender,_deln6merode metroscuadradosde

la zona quedesee relrigerar.

Si lacargade humedadoelcalor essuperioraIo normal,el

aireacondicionadosedeber_ utilizarrnastiempoy con mas

frecuenciaparamantenerlatemperaturaestablecida

deseada. Tambienesposibleque el calorseatan elevado

quetengaque utilizarel aire acondicionadoconstantemente

para mantenerlatemperaturadeseada.

PuedeutilizarelvalorMEDFAN(ventiladormedia)para que

el aire de la habitaci6ncirculey hacerlas condicionesde

habitabilidadmas id6neas,aunquenotengael aire

acondicionadoestablecidoenel modo derefrigeraci6n.As/

disminuirael coste deutilizaci6n.

- 30 -

CARACTERISTICAS

LAUNIDAD

1 5 7 3 6 28 4 FIG. 25

1.CABINA

2. DEFLECTORDEAIRE HORIZONTAL

(Persianavertical)

3.DEFLECTORDEAIRE VERTICAL

(Persianahorizontal)

4.DESCARGADE AIRE

5. REJILLADELANTERA

6. REJILLADELANTERA(entradade aire)

7. FILTRODEAIRE

8.CONTROLDEVENTILACI(_N

EL MANGUITOY LAREJILLATRASERA

FIG. 26

UTILIZACIONDELAPARATODE

AIREACONDICIONADO

_ Antesde utilizarestaunidad,lealas

instruccionesacercade la seguridadparaevitarriesgosde

Iuegos,sacudidael_=ctricaoda5osa personas.

Sigaestospasosparaempezara utilizarel aire

acondicionadodespu6sde su instalaci6n:

1,Conecteelaireacondicionade.(Paraevitarpeligros

electncosnoutilicealargaderasniadaptadores).

2. Establezcaelcontroldetemperatura(TEMP)en elvalorm&s

frio.

3. Establezcael controlde rnodo(MODE)enel nivelmdsfrio.

4.Ajustelaspersianasparaqueelflujode aimle resulte

agradable.

5. Cuandola habitaci6nsehayaenfnado,ajusteelcontrolde

modoytemperaturaenelvalorquele resultem_is

agradable.

NOTA:Si elaireacondicionadeest_lapagado,espereIres

minutosantesdevolveraencenderlo.Deestaformase

equilibrala presi6ndelinteriordelcompresor.Si noesperatres

minutosantesdevolverioa encender,esposiblequese

produzcanfaliosdefuncionamiento.

Sicambieelcontrolde temperaturaarn_,stempladoyvuelvea

carnbiarinmediatamentea unvalorm&sfdo,Launidadde

apagar_.Esperetresminutosantesdevolverioaencendar.

ConsultelasecciOndefuncionesycaracteristicasdelaire

acondicionadoparavet otrosvalores.

CONTROL DE VENTILACION

El controldeventilacionpermiteque elaireacondicionado

hagacircularelaire(CLOSE)o expulseelairealexterior

(OPEN).(FIG.28)

• LaposiciOnCLOSEseutilizacuandodeseela m_xima

refrigeraci6n,Tambienseutilizapararecircularelairesin

refrigerarcuandoelaireacondicicoadeest_eolaposiciOn

FAN(ventilaci0n).

• Enla posici6nOPEN(abiede)eliminaelaireviciadedela

habitaci6ny Ioexpulsaal exterior.El airefrescosaleala

habitaci,Snatravesdelos conductosdeaire normalesdela

casa.

• Laposici6nOPENoCLOSEsepuedeutilizarconcualquier

seleccibndelventilador.

9.CONJUNTODELMANGUITO

(Rejillatraserade aluminioampliadaincluida)

10. REJILLATRASERA

(Rejillatraserade aluminioampliada)

TIRE PARAABRIR / EMPUJE PARA CERRAR

FIG. 27

- 31 -

PANTALLA

Cool •

Energy

Saver •

Fan •

Tlmero TEMP O

CTEMPORIZADOR (TIMER)

- HORADEAPAGADO

• UtJlizardamenudamentelahoradeapagadomientras

duerme.

• Conlaunidadenfuncionamiento,utiliceelTemportzador

parafijarelnL_merodehorashastaelapagade.

•Parasucomodidadduranteelsue_o,unavezfijadalaHora,

laTemperaturafijadaseelevard2°Fdespu_sde30rain.y

2°Fdespu_sdeotros30rain.

• Cadevezqueoprimaelbot6nTempodzador(Timer),lahora

fljadaavanzadelmodesiguiente:1hora_.2horas_"...._"

12horasm_ximo.

- HORADE ENCENDIDO

•Conlaunidadapagada,utiliceelTempodzadorparafijarel

nt_merodehorashastaelencendido.

•CadevezqueoptimaelbotonTemporizador(]]mer),lahora

fijadeavanzadelmodesiguiente:1 hora_"2horas_' ...._'

12horasm_imo.

SENAL DEL

CONTROLREMOTO

DETEMPERATURA(TEMP)

•Utiliceestebot6nparacontrolarautomdticamentela

temperaturadelahabitaci6n.Latemperatura

puedefijarseenuntangode15,6°Ka30°K(60°Fa

86°F)enincrementosdeI°F.

ENCENDIDO (POWER)

•Paraencendedorelaparatodeaire

aconclicionade,opdmaelbot6nON.Para

apagarelaparatodeaireacondicionade,oprima

elbot6ndenuevo.

•Estebot6ntJeneprioridadsobrecualquierotro.

•AIencendedaporprimeravez,launidedestaen

modedeenfriado,velocideddeventiladoralta,

temperaturafijadaa22°K(72°F).

-- VELOCIDAD DE VENTILADOR

(FAN SPEED)

•Cadevezqueoprimeestebot6n,la

configuraci6ncambiasegOnsigue:{Nta-*Baja

_"Media-, Alta)({High-, Low_"Med, High))

MODO (MODE)

- Cadavez queoprtmeestebot6n,cambiardentreFRiO(COOL),AHORRODE ENERG(A(ENERGY

SAVER),VENTILADOR(FAN).

- AHORRO DEENERGiA (ENERGY SAVER)

• Elventiladorse paracuandoelcompresordejade enfriar.Aproximadamentecada3 minutosel

ventiladorse pondr_enmarchay la unidadcomprobar_elaire delahabitaci6nparadeterminarsi

necesitaenfriarse.

rtl:i:f_V[Pl:AVlwlleXoJ,.l#lEell_f,.|l[_

l Cuando vuelve la electricidad despu_s de un corte de suministro electrico, la unidad comenzar& a

funcionar con los _ltimos valores en los que estaba funcionando

- 32 -

CONTROL REMOTO

NOTA:Elcontrolremotonofuncionar&demodeadecuadosiunaluzfuerteest_bnllandosobmlapantalladelsensoronla unidadde

aireacondicionadoo siexistenobstdculonentreel Controlrerontoy elaparatode aireacondicionade.

Cadavez queoprimeunbot6n,seescuchar_,unpitidoprocedentedelaparatodeaireacondieionado.

ENCENDIDO (POWER)

• Paraencenderelaparatodeaireacondicionade,opdmaelbot6nON.Para

apagarelaparatodeaireacondicionado,oprimaelbot6ndenuevo.Estebot6n

tieneprioridadsobrecualquierotto.

AIencenderporprimeravez,launidadest_enmododeenfdado,velocidadde

ventiladoralta,temperaturafijadaa22°K(72°F).

FIJACION DE TEMPERATURA (TEMP)

• Utiliceestebot6nparacontrolarautomdticamentelatemperaturade la

habitaci6n.Latemperaturapuedefijarseen unrangode 15°K(60°F)a30°K

(86°F)enincrementosde I°F.

VELOCIDAD DE VENTILADOR (FAN SPEED)

• Cadavezqueoprimeestebot6n,elvalorfijadocambiaseg0nsigue:

{Alia_"Baja--,Media_ Aita}(High_ Low_"Med-, High)

TEMPORIZADOR (TIMER)

- HORADEAPAGADO

• Utilizardamenudamentela horadeapagadomientrasduerme.

•Conlaunidadenfuncionamiento,utiliceelTemporizadorparafijareln0merode

horashastaelapagado.

•Parasucomodidadduranteelsue_o,unavezfijadalaHora,laTernperaturafijada

seelevara2=,Fdespu_sde30rain.y2°Fdespu_sdeotros30rain.

•Cadavezqueoprimaelbot6nTemporizador(Timer),lahorafijadaavanzadelmodo

siguiente:1hora-, 2horas:- ...._ 12horasm_imo.

- HORADEENCENDIDO

• Conla unidadapagada,utiliceel Temporizadorparafijarel n6merodehorashastael

encendido.

•Cada vezqueoprimaelbot6nTemporizador(Timer),la horafijadavaria del modo

siguiente:1hora_ 2horas_- ....--,t2 horasm_imo.

• Temp •

Fan Speed

MODO (MODE)

-Cada vezqueoprimeestebot6n,cambiardentreFR{O(COOL),AHORRODEENERG{A(ENERGYSAVER),

VENTILADOR(FAN).

- AHORRODEENERGiA

• Elventiladorseparacuandoeleompresordejadeenfriar.

Aproximadamentecada3 minuteselventiladersepondrdenmarchaylaunidadcomprobardelairedelahabitaci6npara

determinarsinecesitaenfriarse.

- 33-

COLOCACI6NDELASPILASDELMANDO

A DISTANCIA

1. Extraiga la tapa de la parte trasera del control

remoto.

2. Inserte dos pilas.

• Aseg_rese de que los polos positivo (+) y

negativo (-) est_.n colocados correctamente.

• Asegerese de que ambas pilas sean nuevas.

3. Vuelva a colocar la tapa.

FIG. 28

AJUSTE DE LA DIRECCI(_N HORIZONTAL

DEL AIRE

• Ladireccibnhorizontaldelaireseajustemoviendola

persianavertical.

• Loselevadoresdelcontrolde lapersianaverticalseubican

a la derechay a la izquierdade la descargade aire.

FIG. 30

• Si novaautilizarelaireaeondieionadoduranteunlargo

periododetiempo,quitelaspilasdolmandoadistanciapara

quenosedescarguen.Guardeelmandoadistancislejosde • Ladirecci_ verticaldel aireseajustemoviendolas

lugaresextremadamenteh0medosocalurosos.Noexpongael

sensorremotoa laluzdirectadelsol parsrnantenerun persianashorizontales.

funcionamiento6primodelmandoadistancia.

• El mandoadistanciasepuedecolocarenlaparedconun

soporte.

AJUSTEDE LADIRECCI6NVERTICALDELAIRE

FIG. 31

- 34 -

LIMPIEZA DELFILTRODE AIRE

Eifiltrode airesepodra ensuciaralquitarel polvo delaparte

intema.Sedeberdlavar al menoscada dossemanas.Si el

filtrode airesigue estandosucio,el flujode aire disminuirdy

la capaeidadderefrigeraei6nsereduciraproduciendodafios

enla unidad.

• Empujelarejillade entradahaciadelantey saqueel filtro

deaire.(FIG. 32)

• Laveel filtro deaire bajo elgrifoconaguatemplada.

Asegi_resede sacudirtodaelagua antesde volvera

colocarel filtro.(FIG. 33)

FIG. 32 FIG. 33

LIMPIEZADELAPARATODEAIRE

ACONDICIONADO

Limpiela rejilladelanteray la rejillade entradacon untrapo

humedecidoen unasoluciSnde detergenteneutro.Lacabina

sedebe limpiarcon unjabSnodetergenteneutroy aguatibia

y, a continuaci6n,pulirlacon ceraliquida.

Paraasegurarla mdximaeficaciacontinua,sedeben

comprobary limpiarperi6dicamentelosserpentinesdel

condensador(parleextemade la unidad)si seobstruyencon

hollinosuciedadde la atmbsfera.Cepilleoaspirelos

serpentinesexterioresparaeliminarlos residuos.

FIG. 34

COMO EXTRAER LA REJILLA

FRONTAL

•Abrala rejilladeentrada.

• Quitelos ternillosqueaseguranlarejilladelantera.

• Empujelarejillahaciaarribadesdeabajoy saquela parte

superiorde larejillade lacarcasaparalevantarlas

pesta_assuperioresdelas ranuras

C()MO VOLVERA COLOCAR LA

REJILLA FRONTAL

Acoplela relilladelanteraala cabinaintrodueiendo1as

pestahasdela rejillaen lasranurasde laparledelanterade

la cabina.Presionesobrela rejillahastaque encajeen su

sitio.

FIG. 36

- 35 -

ANTES DE LLAMAR PARA SERVIClO

Cheque la siguiente lista para asegurarse si en realidad es necesario Ilamar para servicio. Una referencia rapida a

este manual puede evitar una Ilamada para servicio innecesada.

EL EQUIPO DE AIRE ACONDIClONADO NO FUNClONA.

Ele_;hufenoest,,conectadeenlatomade(x)_ientedepared.

Ellusibleest_quemadeoel intem_tordedrcuitosehadisparade.

Elaparatoest_apagade(OFF).

Launidadseapagbysevolvi6aencenderdemas_ador_0kto.

ElcontroldetemperaturaTEMPseajustorn,_scalidoquela

temperaturaambiente.

Conecteelendaufefimlemeflleenlatomadecorrientedepared.

Reemplaceelfuslalo_ conunlusi_ deacelOnmtardadaoreaNsteel

interruptordecirculto.

OptimaelbolOndeencendido.

Apaguelaunidadyespere3minutosantesdevoM_raencenderl_

FijeelcontroldeTEMPenunvalorinferior.

EL AIRE DE LA UNIDAD NO SALE BASTANTE FR{O.

VELOCIDADDELVENllLADOR(FANSPEED)'BpdaenBAJA(LOW)

ControldeTEMP fijadodemasiadoalto,

Latemperaturadela habitael_nesinferiora70°F(21°C).

Eltubosensordetemperaturaest_tocandoel senpentinhioqueest_

sltuadedetr_ delfiltrodelaire.

Optimaelbot_deVELOCIDADDELVENTILADOR(FANSPEED)para_ en_TA (HI).

FijeelcontroldeTEMPaunvalorinferior.

Noseproduolr_enfriamientobasraquelatempemlurade lahabitaci6nse

eleveporenaimade70°F(21°C).

Endereceeltuboale_ndolodelserpentin.

Elfiltrodel elrepuedeestarsuch,

Elcontroldetemperaturaseajust6demasiado,

ELAIREACONDICIONADOENFRiA,PEROLA HABITACIONSESIENTEDEMASIADOC._LIDA;SE FORMA

HIELOENELSERPENTINDEENFRIAMIENTODETRASDEL PANELDECORATIVOFRONTAL.

Latemperaturaexteriores inferiora 70°F(21°C). Parad_lar labobina,ajusleel MODOaVENTILACION,laveloeldaddel

vanltladorenAlia,VENTILElaVELOCIDADaAlto.

Limpieelllttmdeelre.Consultelaseccionsol)reMantenimientoensuGuiadel

Propietarlo.

Paradescongelarlabobina,fijeel MODO(MODE)a Rio (COOL),la valoeldad

delvenlilador(FANSPEED)aAlta(HI)y el controldeTemperatura(TEMP}en

unvalorm&salto.

EL AIRE ACONDICIONADO ENFRfA, PERO LA HABITACI(_N SE SIENTE DEMASIADO CALIDA.

El'Bltrodelaimest_sudoconIoqueserestringeelflujodelaire.

ElcontroldetemperaturaTEMPsegraduoenpoaick_demaaiadocelida.

LaparleITOn_delaunidadest_bloqueadepotco_as, persianas,

m_eblosetc.querestringenla distribud_delaim.

Laspuertas,ventanas,rejillasdecalefacelOn,etc_tera,est_nabieriascon

Ioquesepermlteelescapedelaimfrlo.

Launidadacabadeencenderseenunahabitaaldecalainte.

Umpieelfil_odelaim.Consultelaseoclon"Manteelmientol

FijeelcontroldeTEMPaunvalorinferior.

Elimineel bloqueoenfler,tedelaueldad.

Cierrelaspuerlas,vantanas,re_llasdecalefacciSn,etc_tera.

Permitaquet_rra unpoconkisde_Jempoparaeliminarel"caioralmacenado"

; enlasparades,eltecho,elpisoylosmuebles.

EL EQUIPO DE AIRE ACONDICIONADO SE APAGA Y SE ENCIENDERAPIDAMENTE.

I Latemperaturaexterioresextremadamentecaiiente. I FijelaVELOCIDADDEEVENTILADOR(FANSPEED)aHIlraeraimla

mfngeraci_delpasadeenrellarnasr_pide. I

SE ESCUCHAN RUIDOSCUANDO LA UNIDAD ESTA ENFRIANDO.

Elsonidodelventiladorelchocarcontraelaguadelelstemade Estoesnormalcuandola humedadesaita.Cierrelaspuerias,vantanasylejillas

eliminaelondehumedad, decalefacelde,

Vibmo6ndelaventana;instala_ def_iente. Lealasinsln_cionesdeinstaia_ oconsulteelinstaiador.

EL AGUAGOTEA DENTRO DE LA I'IABITACI(_N CUANDO LA UNIDAD EST.AENFRIANDO.

l Instelaeldeinadecuada I Ird_e_ eleq_°de_ ac_fd_d° i_dabp_ee_'i_p_p_'_r_aimmje_ aguo.Lealasi,ls_u:dmesde_ta_a_'o,_o_saiteaii,-_a_am-.

EL AGUA GOTEA AFUERA CUANDO LA UNIDAD EST._. ENFRIANDO.

habitad6nlaunw_adestaextrayendegrandescan_,t._Jesdehumedaddeunah0meda. I Estoesaigonormaidurantelosdiasexces_vamentehurnedos. I

- 36 -

-37-

m38 _

Master Protection Agreements

Congratulations on making a smart purchase.

Your new Kenmore®product is designed and

manufactured for years of dependable operation.

But like all products, it may require preventive

maintenance or repair from time to time.

That's when having a Master Protection Agreement

can save you money and aggravation.

Purchase a Maser Protection Agreement now and

protect yourseff from unexpected hassle and

expense.

The Master Protection Agreement also helps extend

the life of your new product. Here's what's included

in the Agreement:

[] Expert service by our 12,000 professional

repair specialists

[] Unlimited service and no charge for parts and

labor on all covered repairs

[] "No-lemon" guarantee - replacement of your

covered product iffour or more product failures

occur within twelve months

[] Product replacement if your covered product

can't be fixed

[] Annual Preventive Maintenance Check at your

request - no extra charge

[] Fast help by phone - phone support from a

Sears technician on products requiring in-home

repair, plus convenient repair scheduling

[] Power surge protection against electrical

damage due to power fluctuations

[] Rental reimbursement if repair of your covered

product takes longer than promised

Once you purchase the Agreement, a simple phone

call isall that ittakes for you to schedule service.

You can call anytime day or night, or schedule a

service appointment online.

Sears has over 12,000 professional repair

specialists, who have access to over 4.5 million

quality parts and accessories. That's the kind of

professionalism you can count on to help prolong

the life of your new purchase for years to come.

Purchase your Master Protection Agreement today!

Some limitations and exclusions apply.

For prices and additional information call

1-800-827-6655.

Sears Installation Service

For Sears professional installation of home

appliances, garage door openers, water

heaters, and other major home items, in the

U.S.A. call 1-800-4-MY-HOME °

Acuerdos de Protecci6n Especiallzada

iEnhorabuenalHa realizadouna comprainteligente.

Su nuevo aparatoKenmore_ estddiseSadoy fabricado

para otrecedea_osde buenfuncionamiento.

Sinembargo,al igualquetodoslosproductos,puede

precisarunmantenimientopreventivooinclosealguna

reparacibndevez en cuando.Enesas ocasiones,un

MasterProtectionAgreementpuede ayudade a ahorrar

dineroe inconvenientes.

Adquiera unMaser Protection Agreement ahora,y

prot_jase a s[mismode molestiasy gamesinesperados.

ElMasterProtectionAgreementleayudard tambi_na

prolongarlavidade su nuevoaparato.Lossiguientes

serviciosestdn incluidos:

[] Servicio experto per parte de cualquiera de

nuestros 12.000 t6cnicos profesionalesespecialistas

de Sears.

[] Prestaci6n de servicios sin limitaciones y sin

cargade laspiezasola manede obra entodaslas

reparacionescubiertasporelacuerdo.

[] Garentia seda de sustituci6n de las piezas del

productocubiertoporel acuerdo,sicuatroo rnds

piezas se mostrasendefectuosasen unperiodode

doce meses.

[] Sustituci6n del producto por otro nuevo,siel

defectuoso nopudieserepararse.

[] Controlde mantenlmlento anual preventivo,

siempreque Iodesee ysingastoadicionalalguno.

[] Asistencia telef6nica inmediata de unt_cnico

especialistaen productosquehan de ser reparadosa

domicilio,adem_s de una programaci6nadecuadade

la reparaci6n.

[] Protecci6n contra subidas de tensi6n que

provoquendahosel_,ctdcosdebidos alas

fluctuacionesen elsuministro.

] Reintegro del alquiler si lareparaci6ndelproducto

Ilevarodstiempodel promtetido

Una vez quehayaadquiridoel Agreement,no necesitard

reds queuna simpleIlamadapara solicitarel serviciode

su aparato.Ademds,podrdhacedoen cualquiermomento

deldia ode la ncohe,o solicitarunacitaparaprestaci6n

de serviciosonline.

Searscuentaconmds de 12.000tL,cnicosprofesionales

especialistasen reparaciones,conaccesoa m_sde 4,5

millones de piezasde sustituci6ny acoesoriosdeealidad.

I_steser_eltipode profesionalidady serviciocon elque

podrdcontarparaprolongarla vidade sunuevo producto

pormuchosaSos.iAdquierahoymismosu Master

Protection Agreement!

Se aplioardn algunas Ilmitaclones y

restricciones.

Si desea hacer alguna consulta sobre los

precios u otra informacl6n adicional, le rogamos

Ilame al teldfono 1-800-827-6655.

Servicios de Instalacibn Sears

Para solicitar servicios de instalaci6n profesionales

de Sears de electrodom_sticos, mandos de aperture

de puertas de garejes, calentadores de agua y otros

aparetos en los Estados Unidos, puede Ilamar a

1-800"4-MY-HOME ®

- 39 -

Your Home

For repair - in your home-of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner's manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOME ® (1-800-469-4663)

Call anytime, day or night (U.S.A. and Canada)

www.sears.com www.sears.ca

Our Home

For repair of carry-in items like vacuums, lawn equipment,

and electronics, call or go on-line for the location of your nearest

Sears Parts & Repair Center,

1-800-488-1222

Call anytime, day or night (U.S.A. only)

www.sears.com

To purchase a protection agreement (U.S.A.)

or maintenance agreement (Canada) on a product serviced by Sears:

1-800-827-6655 (U.S.A,) 1-800-361-6665 (Canada)

Para pedir servicio de reparaci6n

a domicilio, y para ordenar piezas:

1-888-SU-HOGAR _

(1-888-784-6427)

Au Canada pour service en fran_ais:

1-800-LE-FOYER _c

(1-800-533-6937)

www.sears.ca

TM S_

® Registered Trademark / Trademark / Service Mark of Sears, Roebuck and Co

TM SM

® Marca Registrada / Marca de Fabrica / Marca de Servicio de Sears, Roebuck and Co.

MC MD

Marque de commerce / Marque d_pos_e de Sears, Roebuck and Co,

Part No.: 3828A20039U

Sears 580.73083300 El manual del propietario

Marca: Sears

Modelo: 580.73083300

Categoría: Acondicionadores de aire de sistema dividido

Tipo: El manual del propietario

Este manual también es adecuado para

Descargar PDF

informe

En otros idiomas

English: Sears 580.73083300 Owner's manual

Sears 580.73083300 El manual del propietario

Este manual también es adecuado para

Sears 580.73083300 El manual del propietario

En otros idiomas

Otros documentos