Yamaha RX-V692 El manual del propietario

Marca: Yamaha

Modelo: RX-V692

Categoría: Reproductores de casete

Tipo: El manual del propietario

OWNER’S MANUAL

MODE D’EMPLOI

MANUAL DE INSTRUCCIONES

Natural Sound AV Receiver

Récepteur audiovisuel “Son Naturel”

Receptor AV de Sonido Natural

R X-V692

R X-V592

Thank you for selecting this YAMAHA AV receiver.

Nous vous remercions d’avoir porté votre choix sur ce récepteur audiovisuel YAMAHA.

Muchas gracias por haber adquirido este receptor AV YAMAHA.

1 Read Instructions – All the safety and operating

instructions should be read before the unit is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the unit and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and other instructions

should be followed.

5 Water and Moisture – The unit should not be used near

water – for example, near a bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement, or near a swimming

pool, etc.

6 Carts and Stands – The unit should be used only with a

cart or stand that is recommended by the

manufacturer.

6A A unit and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause

the unit and

cart combination to overturn.

7 Wall or Ceiling Mounting – The unit should be mounted to

a wall or ceiling only as recommended by the

manufacturer.

8 Ventilation – The unit should be situated so that its

location or position does not interfere with its proper

ventilation. For example, the unit should not be situated

on a bed, sofa, rug, or similar surface, that may block the

ventilation openings; or placed in a built-in installation,

such as a bookcase or cabinet that may impede the flow

of air through the ventilation openings.

9 Heat – The unit should be situated away from heat

sources such as radiators, stoves, or other appliances

that produce heat.

10 Power Sources – The unit should be connected to a

power supply only of the type described in the operating

instructions or as marked on the unit.

11 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the unit.

12 Cleaning – The unit should be cleaned only as

recommended by the manufacturer.

13 Nonuse Periods – The power cord of the unit should be

unplugged from the outlet when left unused for a long

period of time.

14 Object and Liquid Entry – Care should be taken so that

objects do not fall into and liquids are not spilled into the

inside of the unit.

15 Damage Requiring Service – The unit should be serviced

by qualified service personnel when:

A. The power-supply cord or the plug has been

damaged; or

B. Objects have fallen, or liquid has been spilled into the

unit; or

C. The unit has been exposed to rain; or

D. The unit does not appear to operate normally or

exhibits a marked change in performance; or

E. The unit has been dropped, or the cabinet damaged.

16 Servicing – The user should not attempt to service the unit

beyond those means described in the operating

instructions. All other servicing should be referred to

qualified service personnel.

17 Power Lines – An outdoor antenna should be located

away from power lines.

18 Grounding or Polarization – Precautions should be taken

so that the grounding or polarization is not defeated.

SAFETY INSTRUCTIONS

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead

symbol, within an equilateral triangle,

is intended to alert you to the

presence of uninsulated “dangerous

voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an

equilateral triangle is intended to alert

you to the presence of important

operating and maintenance

(servicing) instructions in the

literature accompanying the

appliance.

•

Explanation of Graphical Symbols

CAUTION

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS

UNIT TO RAIN OR MOISTURE.

English

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be

connected to the grounding system of the building, as

close to the point of cable entry as practical.

SPECIAL NOTES FOR FCC COMPOSITE

DEVICE (for US customers only)

This device is a composite system. The digital device

component may not cause harmful interference.

19 For US customers only:

Outdoor Antenna Grounding – If an outside antenna is

connected to this unit, be sure the antenna system is

grounded so as to provide some protection against

voltage surges and built-up static charges. Article 810 of

the National Electrical Code, ANSI/NFPA 70, provides

information with regard to proper grounding of the mast

and supporting structure, grounding of the lead-in wire to

an antenna discharge unit, size of grounding conductors,

location of antenna discharge unit, connection to

grounding electrodes, and requirements for the grounding

electrode.

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC – NATIONAL ELECTRICAL CODE

1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC, to

use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high quality

shielded cables. Cable/s supplied with this product

MUST be used. Follow all installation instructions.

Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC Regulations,

Part 15 for Class “B” digital devices. Compliance with

these requirements provides a reasonable level of

assurance that your use of this product in a residential

environment will not result in harmful interference with

other electronic devices.

This equipment generates/uses radio frequencies and, if

not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product

is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try

to eliminate the problem by using one of the following

measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

FCC INFORMATION (for US customers only)

YAMAHA and the Electronic Industries Association’s

Consumer Electronics Group want you to get the most out of

your equipment by playing it at a safe level. One that lets the

sound come through loud and clear without annoying blaring

or distortion – and, most importantly, without affecting your

sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

We Want You Listening For A Lifetime (for US customers only)

CONTENTS

SUPPLIED ACCESSORIES

After unpacking, check that the following parts are included.

Safety Instructions ...............Inside the Front Cover

Supplied Accessories ......................................2

Features ..........................................................3

Caution ............................................................4

Notes about the Remote Control Transmitter

........................................................................5

Profile of This Unit ...........................................6

Speaker Setup ................................................7

Connections ....................................................8

Controls and Their Functions ........................16

Speaker Balance Adjustment ........................20

Basic Operations ...........................................23

Tuning Operations .........................................26

Preset Tuning ................................................27

Using Digital Sound Field Processor (DSP)

......................................................................30

Setting the SLEEP Timer ..............................35

Remote Control Transmitter ..........................36

Troubleshooting .............................................46

Specifications ................................................47

Indoor FM Antenna

AM Loop Antenna

Antenna adapter (U.S.A. and Canada models only)

Batteries (size AA, R6, UM-3)

Remote Control Transmitter

User function stickers

English

FEATURES

●

5 Speaker Configuration

RX-V692

U.S.A. and Canada models

Main: 80W + 80W (8Ω) RMS Output

Power, 0.04% THD, 20–20,000 Hz

Center: 80W (8Ω) RMS Output Power,

0.07% THD, 20–20,000 Hz

Rear: 40W + 40W (8Ω) RMS Output

Power, 0.3% THD, 1 kHz

Australia, Singapore and General

models

Main: 75W + 75W (8Ω) RMS Output

Power, 0.04% THD, 20–20,000 Hz

Center: 75W (8Ω) RMS Output Power,

0.07% THD, 20–20,000 Hz

Rear: 40W + 40W (8Ω) RMS Output

Power, 0.3% THD, 1 kHz

RX-V592

U.S.A. and Canada models

Main: 75W + 75W (8Ω) RMS Output

Power, 0.04% THD, 20–20,000 Hz

Center: 75W (8Ω) RMS Output Power,

0.07% THD, 20–20,000 Hz

Rear: 35W + 35W (8Ω) RMS Output

Power, 0.3% THD, 1 kHz

Australia, Singapore and General

models

Main: 70W + 70W (8Ω) RMS Output

Power, 0.04% THD, 20–20,000 Hz

Center: 70W (8Ω) RMS Output Power,

0.07% THD, 20–20,000 Hz

Rear: 35W + 35W (8Ω) RMS Output

Power, 0.3% THD, 1 kHz

●

Digital Sound Field Processor

●

Dolby Pro Logic Surround Decoder

●

Theater-like Sound Experience by the

Combination of Dolby Pro Logic and

YAMAHA DSP Technology (CINEMA DSP)

●

Automatic Input Balance Control for

Dolby Pro Logic Surround

●

Test Tone Generator for Easier Speaker

Balance Adjustment

●

3 Center Channel Modes

(NORMAL/WIDE/PHANTOM)

● BASS EXTENSION Switch for Reinforcing

Bass Response

● 40-Station Random Access Preset Tuning

● Automatic Preset Tuning

● Preset Station Shifting Capability (Preset

Editing)

● IF Count Direct PLL Synthesizer Tuning

System

● Video Signal Input/Output Capability

● 6-Channel Discrete Input Terminals for

Connecting with a Dolby Digital (AC-3)

Decoder

● SLEEP Timer

●

“Learning” Remote Control Transmitter

CAUTION : READ THIS BEFORE OPERATING YOUR UNIT.

1. To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2. Install this unit in a cool, dry, clean place – away from

windows, heat sources, sources of excessive vibration,

dust, moisture and cold. Avoid sources of humming

(transformers, motors). To prevent fire or electrical shock,

do not expose the unit to rain or water.

3. Never open the cabinet. If something drops into the set,

contact your dealer.

4. Do not use force on switches, controls or connection wires.

When moving the unit, first disconnect the power plug and

the wires connected to other equipment. Never pull the

wires themselves.

5. The openings on the cabinet assure proper ventilation of

the unit. If these openings are obstructed, the temperature

inside the cabinet will rise rapidly. Therefore, avoid placing

objects against these openings, and install the unit in well-

ventilated condition. Make sure to allow a space of at least

10 cm behind, 20 cm on the both sides and 30 cm above

the top panel of the unit. Otherwise it may not only damage

the unit, but also cause fire.

6. Always set the VOLUME control to “–

∞

” before starting

the audio source play. Increase the volume gradually to an

appropriate level after playback has been started.

7. Do not attempt to clean the unit with chemical solvents;

this might damage the finish. Use a clean, dry cloth.

8. Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before concluding that

the unit is faulty.

9. When not planning to use this unit for long periods of time

(ie., vacation, etc.), disconnect the AC power plug from the

wall outlet.

10.To prevent lightning damage, disconnect the AC power

plug and disconnect the antenna cable when there is an

electrical storm.

11.Grounding or polarization – Precautions should be taken

so that the grounding or polarization of an appliance is not

defeated.

12.AC outlet

Do not connect audio equipment to the AC outlet on the

rear panel if that equipment requires more power than the

outlet is rated to provide.

13.Voltage Selector (General Model only)

The voltage selector on the rear panel of this unit must

be set for your local main voltage BEFORE plugging

into the AC main supply.

Voltages are 110/120/220/240 V AC, 50/60 Hz.

IMPORTANT

Please record the serial number of this unit in the space

below.

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

FOR CANADIAN CUSTOMERS

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE

OF PLUG TO WIDE SLOT AND FULLY INSERT.

THIS CLASS B DIGITAL APPARATUS MEETS ALL

REQUIREMENTS OF THE CANADIAN INTERFERENCE-

CAUSING EQUIPMENT REGULATIONS.

The apparatus is not disconnected from the AC power

source as long as it is connected to the wall outlet, even if

the apparatus itself is turned off.

FREQUENCY STEP switch (General Model only)

Because the interstation frequency spacing differs in

different areas, set the FREQUENCY STEP switch (located

at the rear) according to the frequency spacing in your area.

Before setting this switch, disconnect the AC power plug of

this unit from the AC outlet.

English

NOTES ABOUT THE REMOTE CONTROL TRANSMITTER

Battery installation

Battery replacement

If you find that the remote control transmitter must be used

closer to the main unit, the batteries are weak. Replace both

batteries with new ones.

Notes

●

Use only AA, R6, UM-3 batteries for replacement.

●

Be sure the polarities are correct. (See the illustration inside

the battery compartment.)

●

Remove the batteries if the remote control transmitter will not

be used for an extended period of time.

●

If batteries leak, dispose of them immediately. Avoid

touching the leaked material or letting it come in contact with

clothing, etc. Clean the battery compartment thoroughly

before installing new batteries.

●

After you change batteries, make sure to press the RESET

button inside the battery compartment.

Remote control transmitter operation range

Notes

●

There should be no large obstacles between the remote

control transmitter and the main unit.

●

If the remote control sensor is directly illuminated by strong

lighting (especially an inverter type of fluorescent lamp etc.),

it might cause the remote control transmitter not to work

correctly. In this case, reposition the main unit to avoid direct

lighting.

–dB

30°

Remote control

sensor

Within approximately

6 m (19.7 feet)

PROFILE OF THIS UNIT

You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field

Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to

bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system,

and this unit will sonically transform your room into a wide range of listening environments –movie theater, concert hall, and so on.

In addition, you get incredible realism from sources encoded with Dolby Surround using the built-in Dolby Pro Logic Surround

Decoder.

Please read this operation manual carefully and store it in a safe place for later reference.

Digital Sound Field Processing

What is it that makes live music so good? Today’s advanced

sound reproduction technology lets you get extremely close to

the sound of a live performance, but chances are you’ll still

notice something missing: the acoustic environment of the live

concert hall. Extensive research into the exact nature of the

sonic reflections that create the ambience of a large hall has

made it possible for Yamaha engineers to bring you this same

sound in your own listening room, so you’ll feel all the sound of

a live concert.

Furthermore, our technicians, armed with sophisticated

measuring equipment, have even made it possible to capture

the acoustics of a variety of venues such as an actual concert

hall, theater, etc. to allow you to accurately recreate one of

several actual live performance environments, all in your own

home.

Dolby Pro Logic Surround

This unit employs a Dolby Pro Logic Surround decoder similar

to professional Dolby Stereo decoders used in many movie

theaters. By using the Dolby Pro Logic Surround decoder, you

can experience the dramatic realism and impact of Dolby

Surround movie theater sound in your own home. Dolby Pro

Logic employs a four channel five speaker system. The Pro

Logic Surround system divides the input signal into four levels:

the left and right main channels, the center channel (used for

dialog), and the rear surround sound channels (used for sound

effects, background noise, and other ambient noises). The

center channel allows listeners seated in even less-than-ideal

positions to hear the dialog originating from the action on the

screen while experiencing good stereo imaging.

Dolby Surround is encoded on the sound track of pre-recorded

video tapes, laser discs, and some TV/cable broadcasts. When

you play a source encoded with Dolby Surround on this unit,

the Dolby Pro Logic Surround decoder decodes the signal and

distributes the surround-sound effects.

This Dolby Pro Logic Surround Decoder employs a digital

signal processing system. This system improves the stability of

sound at each channel and minimizes crosstalk between

channels, so that positioning of sounds around the room is

more accurate compared with conventional analog signal

processing systems.

In addition, this unit features a built-in automatic input balance

control. This always assures you the best performance without

manual adjustment.

Manufactured under license from Dolby Laboratories Licensing

Corporation. “Dolby”, “AC-3”, “Pro Logic”, and the double-D

symbol are trademarks of Dolby Laboratories Licensing

Corporation.

Dolby Pro Logic Surround + DSP

Dolby Surround sound system shows its full ability in a large

movie theater, because movie sounds are originally designed

to be reproduced in a large movie theater using many

speakers. It is difficult to create a sound environment similar to

that of a movie theater in your listening room, because the

room size, materials of inside walls, the number of speakers,

etc. of your listening room is much different from those of a

movie theater.

Yamaha DSP technology made it possible to present you with

nearly the same sound experience as that of a large movie

theater in your listening room by compensating for lack of

presence and dynamics in your listening room with its original

digital sound fields combined with Dolby Surround sound field.

The combination of Dolby Pro Logic Surround and DSP is used

on the sound field program “ PRO LOGIC ENHANCED”.

RX-V692 only

This combination is used on sound field programs “ PRO

LOGIC ENHANCED”, “70 mm MOVIE THEATER” and “TV

SPORTS”.

The YAMAHA “CINEMA DSP” logo indicates these programs are

created by the combination of Dolby Pro Logic and YAMAHA

DSP technology.

CINEMA DSP

English

SPEAKER SETUP

SPEAKERS TO BE USED

This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective speakers to use with

this unit are main speakers, rear speakers and a center speaker. You may omit the center speaker. (Refer to the “4-Speaker

Configuration” shown below.)

The main speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your

present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center

sounds (dialog etc.) within programs encoded with Dolby Surround. The center speaker needs to be equal in power to the main

speakers, although the rear speakers should not be equal. However, all the speakers should have high enough power handling to

accept the maximum output of this unit.

SPEAKER CONFIGURATION

5-Speaker Configuration

This configuration is the most effective and recommended one.

In this configuration, the center speaker is necessary as well as

the rear speakers. If one of the programs shown below is

selected, conversations will be output from the center speaker

and the ambience will be excellent.

• PRO LOGIC

• PRO LOGIC ENHANCED

• 70 mm MOVIE THEATER RX-V692 only

• TV SPORTS RX-V692 only

Note: Set the center channel mode to the “NORMAL” or

“WIDE” position. (For details, refer to page 21.)

4-Speaker Configuration

The center speaker is not used in this configuration. If one of

the programs shown below is selected, the center sound is

output from the left and the right main speakers. However, the

sound effect of other programs can be the same as that of the

5-speaker configuration.

• PRO LOGIC

• PRO LOGIC ENHANCED

• 70 mm MOVIE THEATER RX-V692 only

• TV SPORTS RX-V692 only

Note: Be sure to set the center channel mode to the

“PHANTOM” position. (For details, refer to page 21.)

SPEAKER PLACEMENT

The recommended speaker configuration, the 5-speaker configuration, will require two speaker pairs: main speakers (your normal

stereo speakers), and rear speakers, plus a center speaker. When you place these speakers, refer to the following.

Main: In normal position. (The position of your present

stereo speaker system.)

Rear: Behind your listening position, facing slightly inward.

Nearly six feet (approx. 1.8 m) up from the floor.

Center: Precisely between the main speakers. (To avoid

interference with TV sets, use a magnetically shielded

speaker.)

Front L Center Front R

Dialogue

Surround sound

Dialogue

Surround sound

Rear L

Rear R

Front L Front R

Dialogue

Surround sound

Dialogue

Surround sound

Rear L Rear R

Front R

Center

Front L

TV set

Rear R

Rear L

Main L

Main R

Main L

Main R

Main L

Main R

CONNECTIONS

Never plug in this unit and other components until all connections are completed.

CONNECTIONS WITH OTHER COMPONENTS

When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left)

to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.

* If you have YAMAHA components numbered as 1, 2, 3, etc. on the rear panel, connections can be made easily by making sure

to connect the output (or input) terminals of each component to the same-numbered terminals of this unit.

: See the next page.

ANT

GND

75Ω UNBAL.

GND

MONITOR

OUT

DVD/LD

TV/DBS

VIDEO

IN OUT

VCR

VIDEO SIGNAL

PHONO CD

TAPE ( MD ) DVD/LD

TV/DBS

VCR

TAPE

REC

OUT

IN OUT

AUDIO SIGNAL

1 3 4

MAIN CENTER REAR

(SURROUND)

OUTPUT

SUB

WOOFER

6CH DISCRETE INPUT

DVD/LD TV/DBS

SURROUND

CENTERMAIN

REAR

(SURROUND)

CENTER

DUAL

SINGLE

CAUTION

SEE INSTRUCTION MANUAL FOR CORRECT SETTING.

MAIN

SPEAKERS

SUB

WOOFER

MAINS

IMPEDANCE SELECTOR

SWITCHED

I20V 60Hz

I00W MAX. TOTAL

AC OUTLETS

SINGLE

Ω

MIN. /SPEAKER

DUAL

Ω

MIN. /SPEAKER

CENTER

MAIN

REAR 6

Ω

MIN. /SPEAKER

A OR B

Ω

MIN. /SPEAKER

A B

Ω

MIN. /SPEAKER

SINGLE

Ω

MIN. /SPEAKER

DUAL

Ω

MIN. /SPEAKER

CENTER

MAIN

REAR 8

Ω

MIN. /SPEAKER

A OR B

Ω

MIN. /SPEAKER

A B

:I6

Ω

MIN. /SPEAKER

GND

OUTPUT

LINE OUT

LINE IN

VIDEO OUT

AUDIO OUT

AUDIO IN

VIDEO IN

VIDEO OUT

VIDEO IN

AUDIO OUT

VIDEO OUT

(U.S.A. model)

To AC outlet

Turntable LD player etc.

Video cassette recorder

TV/Satellite tuner

Tape deck,

MD recorder, etc.

CD player

Monitor TV

English

AC OUTLET(S) (SWITCHED)

(U.S.A., Canada, Singapore and General models)

.......................................................... 2 SWITCHED OUTLETS

(Australia model) ................................. 1 SWITCHED OUTLET

Use these to connect the power cords from your components

to this unit.

The power to the SWITCHED outlets is controlled by this unit’s

POWER switch or the provided remote control transmitter’s

POWER key. These outlets will supply power to any

component whenever this unit is turned on.

The maximum power (total power consumption of components)

that can be connected to the SWITCHED AC OUTLET(S) is

100 watts.

GND terminal (For turntable use)

Connecting the ground wire of the turntable to the GND

terminal will normally minimize hum, but in some cases better

results may be obtained with the ground wire disconnected.

CONNECTING TO VIDEO AUX TERMINALS (ON THE FRONT PANEL)

These terminals are used to connect any video input source such as a camcorder to this unit.

Camcorder

S VIDEO

VIDEO

VIDEO AUX

S VIDEO VIDEO L AUDIO R

VIDEO OUT

S VIDEO OUT

AUDIO OUT L

AUDIO OUT R

: S VIDEO terminal is provided for RX-V692 only.

Connecting with a Dolby Digital (AC-3) Decoder

If you have a Dolby Digital (AC-3) Decoder unit or an LD player etc. which incorporates a Dolby Digital (AC-3) Decoder, its discrete

outputs can be connected to this unit.

Notes

• The laserdisc player (or another unit) must be also

connected to the DVD/LD (or TV/DBS) AUDIO SIGNAL input

terminals of this unit for playing a source with the Dolby Pro

Logic Surround decoded or in normal stereo (or monaural).

• The discrete signals input to this unit cannot be recorded by

a tape deck, MD recorder or VCR. To record a source played

on the laserdisc player (or another unit), it must be

connected to the DVD/LD (or TV/DBS) AUDIO/VIDEO

SIGNAL input terminals of this unit.

• If you made no connection to the SUBWOOFER input

terminal of this unit or you will not use a subwoofer, you

should make a setting for distributing signals at the LFE

channel to the right and left MAIN output terminals on the

Dolby Digital (AC-3) Decoder unit.

For details, refer to the owner’s manual for the Dolby Digital

(AC-3) Decoder unit.

ANT

GND

75Ω UNBAL.

GND

MONITOR

OUT

DVD/LD

TV/DBS

VIDEO

IN OUT

VCR

VIDEO SIGNAL

PHONO CD

TAPE ( MD ) DVD/LD

TV/DBS

VCR

TAPE

REC

OUT

IN OUT

AUDIO SIGNAL

1 3 4

6CH DISCRETE INPUT

DVD/LD TV/DBS

SURROUND

CENTERMAIN

SUB

WOOFER

MONITOR

OUT

S VIDEO

IN OUT

VCR

AC-3 RF

OUT

AC-3 RF

DIGITAL

OUT

VIDEO OUT

AUDIO OUT

6CH DISCRETE OUTPUT

CENTER SURROUNDMAIN

SUB

WOOFER

Dolby Digital (AC-3) Decoder unit

RF Demodulator

Laserdisc player with AC-3 RF output or

another unit with AC-3 RF output

English

RX-V692 only

CONNECTING TO S VIDEO TERMINALS

If you have a video cassette recorder and a monitor equipped with “S” (high-resolution) video terminals, those terminals can be

connected to this unit’s S VIDEO terminals. Connect the video cassette recorder’s “S” video input and output terminals to this unit’s

S VIDEO VCR IN and OUT terminals respectively, and connect the monitor’s “S” video input terminal to this unit’s S VIDEO

MONITOR OUT terminal. Otherwise, connect the video cassette recorder’s composite video terminals to this unit’s composite video

terminals, and connect the monitor’s composite video input terminal to this unit’s composite MONITOR OUT terminal.

Note

If video signals are sent to both S VIDEO input and composite input terminals, the signals will be sent to their respective

output terminals independently.

S VIDEO

VIDEO

S VIDEO

OUT

S VIDEO

VIDEO OUT

VIDEO IN

MONITOR

OUT

DVD/LD

TV/DBS

VIDEO

IN OUT

VCR

VIDEO SIGNAL

MONITOR

OUT

S VIDEO

IN OUT

VCR

ON SCREEN SELECTOR

S VIDEO VIDEOPAL NTSC

Video cassette recorder

Monitor TV

If you connect a video cassette recorder, LD player, video

monitor, etc. to this unit, you can display DSP program names

and information about other settings and adjustments on the

video monitor screen which is connected to the composite

VIDEO (or S VIDEO) MONITOR OUT terminal of this unit.

Information is superimposed over the video image.

If there is no program material on the monitor, the information

will be displayed over a monochromatic background.

By using the S VIDEO/VIDEO switch, select the video monitor

connected to the S VIDEO or composite VIDEO MONITOR

OUT terminal on which you want to display the screen display

information.

S VIDEO/VIDEO switch

S VIDEO: In this position, the screen display information is

displayed on the video monitor connected to the S

VIDEO MONITOR OUT terminal.

VIDEO: In this position, the screen display information is

displayed on the video monitor connected to the

composite VIDEO MONITOR OUT terminal.

PAL/NTSC switch (General model only)

PAL: Set to this position if your monitor TV employs the

PAL format.

NTSC: Set to this position if your monitor TV employs the

NTSC format.

Note

Make sure to play back a video source which employs the

same format that your monitor TV employs, otherwise a picture

will not be played back normally.

RX-V692 only

ON SCREEN DISPLAY

: Provided for General model

only.

CONNECTING SPEAKERS

MAIN CENTER REAR

(SURROUND)

OUTPUT

SUB

WOOFER

REAR

(SURROUND)

CENTER

DUAL

SINGLE

CAUTION

SEE INSTRUCTION MANUAL FOR CORRECT SETTING.

MAIN

SPEAKERS

IMPEDANCE SELECTOR

SINGLE

Ω

MIN. /SPEAKER

DUAL

Ω

MIN. /SPEAKER

CENTER

MAIN

REAR 6

Ω

MIN. /SPEAKER

A OR B

Ω

MIN. /SPEAKER

A B

Ω

MIN. /SPEAKER

SINGLE

Ω

MIN. /SPEAKER

DUAL

Ω

MIN. /SPEAKER

CENTER

MAIN

REAR 8

Ω

MIN. /SPEAKER

A OR B

Ω

MIN. /SPEAKER

A B

:I6

Ω

MIN. /SPEAKER

Rear speaker Rear speaker

Center speaker

Main speakers B

Left

Right

Left

Right

Main speakers A

Subwoofer system

Left

Right

Note

Use speakers with the specified impedance shown on the rear

of this unit.

Note on main speaker connections:

One or two speaker systems can be connected to this unit. If

you use only one speaker system, connect it to either the

SPEAKERS A or B terminals.

Note on a subwoofer connection:

You may wish to add a subwoofer to reinforce low frequencies

or to output low bass sound from the subwoofer channel when

reproducing discrete signals.

Connect the SUBWOOFER OUTPUT terminal of this unit to

the INPUT terminal of the subwoofer amplifier, and connect the

speaker terminals of the subwoofer amplifier to the subwoofer.

With some subwoofers, including the Yamaha Active Servo

Processing Subwoofer System, the amplifier and subwoofer

are in the same unit.

Note on center speaker connection:

One or two center speakers can be connected to this unit. If

you cannot place the center speaker on or under the TV, it is

recommended to use two center speakers and place them on

both sides of the TV to orient the center sound at the center

position. For connecting two center speakers, follow the

method shown below.

REAR

(SURROUND)

CENTER

DUAL

SINGLE

Center speaker

(U.S.A. model)

English

For connecting to the MAIN SPEAKERS terminals

Red: positive (+)

Black: negative (–)

➀

Unscrew the knob.

➁

Insert the bare wire.

[Remove approx. 5mm

(1/4”) insulation from

the speaker wires.]

➂

Tighten the knob and

secure the wire.

Banana Plug connections are also possible (except for

Singapore model). Simply insert the Banana Plug connector

into the corresponding terminal.

For connecting to the REAR and CENTER SPEAKERS

terminals

Red: positive (+)

Black: negative (–)

➀

Press the tab.

➁

Insert the bare wire.

[Remove approx. 5mm

(1/4”) insulation from

the speaker wires.]

➂

Release the tab and

secure the wire.

➁

➂

➀

How to Connect:

Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are

faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and –

markings are observed. If these wires are reversed, the sound will be unnatural and lack bass.

Caution

Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could damage

this unit and/or speakers.

For Custom Installer

For U.S.A. and Canada models of RX-V692 only

REMOTE CONTROL (IN, OUT) terminals

These terminals are used for custom installation system.

When this unit is connected to the components for custom

installation system, you can operate this unit with the

system remote control.

Connect the REMOTE CONTROL IN terminal of this unit to

the output terminal of the central controller for custom

installation system.

By connecting the REMOTE CONTROL OUT terminal of

this unit to the REMOTE CONTROL IN terminal of the other

component, you can also operate it with the system remote

control. In this way, up to 6 components can be connected

in series.

VIDEO SIGNAL

DVD/LD TV/DBS

SURROUND

ON SCREEN SELECTOR

S VIDEO VIDEO

REMOTE CONTROL

IN OUT

MAIN OUTPUT terminals

These terminals are for main channel line output. There is no

connection to these terminals when you use the built-in

amplifier.

However, if you drive main speakers with an external stereo

power amplifier, connect the input terminals of the external

amplifier (MAIN IN or AUX terminals of a power amplifier or an

integrated amplifier) to these terminals.

* Output signals from the MAIN OUTPUT terminals only are

affected by the use of BASS, TREBLE, BALANCE controls

and BASS EXTENSION switch.

CENTER OUTPUT terminal

This terminal is for center channel line output. There is no

connection to this terminal when you use the built-in amplifier.

However, if you drive a center speaker with an external power

amplifier, connect the input terminal of the external amplifier to

this terminal.

REAR (SURROUND) OUTPUT terminals

These terminals are for rear channel line output. There is no

connection to these terminals when you use the built-in

amplifier.

However, if you drive rear speakers with an external stereo

power amplifier, connect the input terminals of the external

amplifier (MAIN IN or AUX terminals of a power amplifier or an

integrated amplifier) to these terminals.

SUBWOOFER OUTPUT terminal

This terminal is for connecting with the input terminal of an

amplifier for driving a subwoofer.

When the input signals to this unit are in normal 2-channel

stereo, this terminal outputs only frequencies below 200 Hz

from the main and center channels. When discrete signals are

input to this unit and are selected as the input source, this

terminal outputs signals from the subwoofer channel.

Note

Output level of signals from all of these terminals are adjusted

by the use of VOLUME control on the front panel or MASTER

VOLUME keys on the remote control transmitter.

OUTPUT terminals (for driving speakers with external amplifiers)

Be sure to switch this only when the power of this unit is turned

off.

Select the position whose requirements your speaker system

meets.

(Upper position)

Rear: The impedance of each speaker must be 6Ω or

higher.

Center: If you use one center speaker, the impedance of the

speaker must be 6Ω or higher.

If you use two center speakers, the impedance of

each speaker must be 3Ω or higher.

Main: If you use one pair of main speakers, the impedance

of each speaker must be 4Ω or higher.

If you use two pairs of main speakers, the impedance

of each speaker must be 8Ω or higher.

(Lower position)

Rear: The impedance of each speaker must be 8Ω or

higher.

Center: If you use one center speaker, the impedance of the

speaker must be 8Ω or higher.

If you use two center speakers, the impedance of

each speaker must be 4Ω or higher.

Main: If you use one pair of main speakers, the impedance

of each speaker must be 8Ω or higher.

If you use two pairs of main speakers, the impedance

of each speaker must be 16Ω or higher.

IMPEDANCE SELECTOR switch

IMPEDANCE SELECTOR

SINGLE

Ω

MIN. /SPEAKER

DUAL

Ω

MIN. /SPEAKER

CENTER

MAIN

REAR 6

Ω

MIN. /SPEAKER

A OR B

Ω

MIN. /SPEAKER

A B

Ω

MIN. /SPEAKER

SINGLE

Ω

MIN. /SPEAKER

DUAL

Ω

MIN. /SPEAKER

CENTER

MAIN

REAR 8

Ω

MIN. /SPEAKER

A OR B

Ω

MIN. /SPEAKER

A B

:I6

Ω

MIN. /SPEAKER

MAIN CENTER REAR

(SURROUND)

OUTPUT

SUB

WOOFER

(U.S.A. model)

English

ANTENNA CONNECTIONS

●

Each antenna should be connected to the designated terminals correctly, referring to the following diagram.

●

Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal

strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience

poor reception quality, an outdoor antenna may result in improvement.

Connecting the AM loop antenna

* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.

* The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.

GND terminal

For maximum safety and minimum interference, connect the

GND terminal to a good earth ground. A good earth ground is

a metal stake driven into moist earth.

Notes

●

When connecting the indoor

FM antenna, insert its

connector into the FM ANT

terminal firmly.

●

If you need an outdoor

FM antenna to improve

FM reception quality, either

300-ohm feeder or coaxial cable may be used. In locations

troubled by electrical interference, coaxial cable is

preferable.

ANT

GND

75Ω UNBAL.

GND

PHONO

➀

➁

➂

Orient so that the best

reception is obtained.

1 2 3

Outdoor FM antenna

Outdoor AM antenna

AM loop

antenna

(included)

Ground

75-ohm/300-ohm

antenna adapter

75-ohm/300-ohm

antenna adapter

75-ohm coaxial cable

300-ohm feeder

Indoor FM

antenna

(included)

CONTROLS AND THEIR FUNCTIONS

FRONT PANEL

PRO LOGIC

ENHANCED

70 mm

MOVIE THEATER

SPORTS

STADIUM

POWER

NATURAL SOUND AV RECEIVER

RX–V692

SPEAKERSPHONES

OFF

BASS TREBLE BALANCE

VIDEO AUX

S VIDEO VIDEO L AUDIO R

VOLUME

–dB

BASS

EXTENSION

TONE

BYPASS

CINEMA DSP

DELAY/CENTER

/REAR/SWFR

MAN'L

AUTO FM

TUNING

MODE

AUTO

MAN'L MONO

CENTER

MODE

DISCO

CONCERT

HALL

ROCK

CONCERT

EFFECT

CHURCHJAZZ CLUB

DOWN

TUNING

MEMORY

EDIT

TIME

LEVEL

VCR DVD

LDTV

DBS

VIDEO AUX

TAPE (MD) MON 2CH/6CH

TUNER

PHONO

2 3 4 5 6 7 8

PRESET

kHz

MHz

MEMORY

SLEEPAUTO

TAPE 2 MONITOR

DIGITAL

STEREO

l00

ROOM 2 CONTROL

NORMAL WIDEPHANTOM

40 60

SPEAKERS

RTPS PTY

PTY HOLD

EON

NEWS

INFO AFFAIRS SPORT

PCM AC

—

DSP

PRO LOGIC

DIGITALDIGITAL

AUTO TUNING

SPEAKERS

ROOM 2

ENHANCED

0A BCD E F G HIJ

23 4 5 6 7 8 9

NATURAL SOUND AV RECEIVER

RX–V592

CINEMA DSP

OFF

PRO LOGIC

ENHANCED

CONCERT

VIDEO

MONO

MOVIE

STADIUM

POWER

SPEAKERSPHONES

BASS TREBLE BALANCE

VIDEO AUX

VIDEO L AUDIO R

VOLUME

–dB

BASS

EXTENSION

DELAY/CENTER

/REAR/SWFR

MAN'L

AUTO FM

TUNING

MODE

AUTO

MAN'L MONO

CENTER

MODE

DISCO

CONCERT

HALL

ROCK

CONCERT

EFFECT

DOWN

TUNING

MEMORY

EDIT

TIME

LEVEL

PRESET

kHz

MHz

MEMORY

AUTO PTY HOLD

SLEEP

TAPE MONITOR

STEREO

ms dB

PRO LOGIC

ENHANCED

CONCERT

VIDEO

MONO

MOVIE

STADIUM

DISCO

ROCK CONCERT

CONCERT HALL

2 3 4 5 6 7 8

VCR DVD

LDTV

DBS

VIDEO AUX

TUNER

PHONO

NORMAL

WIDE

PHANTOM

EFFECT OFF

EON

INFO AFFAIRS SPORT

NEWS

RT CTPTY

l00

40 60

0A BC E F G H IJ

MNLO

23 4 5 6 789

TAPE (MD) MON 2CH/6CH

RX-V692

RX-V592

English

1 POWER switch

Press this switch to switch the power on. Press it again to

switch the power off.

2 Standby mode indicator

(Except U.S.A. and Canada models)

While the power is on, pressing the SYSTEM POWER OFF

key on the remote control transmitter switches the unit to the

standby mode. In this mode, this indicator is illuminated.

3 Remote control sensor

Receives signals from the remote control transmitter.

4 Display panel

Shows various information. (Refer to page 18–19 for details.)

5 Input selector buttons

Select a program source to listen to or watch. When a button is

pressed, the name of selected source appears on the display.

6 DSP program selector buttons

Select a DSP program. When a button is pressed, the name of

selected program lights up on the display.

7 2CH/6CH selector button

When the TV/DBS or DVD/LD input source is selected,

pressing this button switches the input signals between 2

channel stereo signals and 6 channel discrete signals. When

switched to “6CH”, discrete signals from the unit connected to

the 6CH DISCRETE INPUT DVD/LD TV/DBS terminals of this

unit are selected as the input signals.

8 EFFECT button

Switches on/off the digital sound field processor (including the

Dolby Pro Logic Surround decoder).

9 VOLUME control

Used to raise or lower the volume level.

0 PHONES jack

When you listen with headphones, connect the headphones to

the PHONES jack. You can listen to the sound to be output

from the main speakers through headphones.

When listening with headphones privately, set both the

SPEAKERS A and B switches to the OFF position and switch

off the digital sound field processor (so that no DSP program

name is illuminated on the display) by pressing the EFFECT

button.

A SPEAKERS switches

Set the switch A or B (or both A and B) for the main speaker

system (connected to this unit) you will use to the ON position.

Set the switch for the main speaker system you will not use to

the OFF position.

B A/B/C/D/E button

Press this button to select a desired group (A–E) of preset

stations.

C BASS EXTENSION switch

When this switch is pressed inward (ON), boosts bass

frequency response at the main left and main right channels

while maintaining overall tonal balance. If you do not have a

subwoofer, the use of this switch will be effective to reinforce

the bass frequencies.

D TONE BYPASS switch

RX-V692 only

When this switch is pressed inward (ON), the input signal does

not pass through the tone control circuitry so that it is

unaffected by the tone control circuitry. Use this switch to

obtain pure sound and to check the tone control setting. Press

this switch to release it outward (OFF) to use the tone control

circuitry.

E Preset station number selector buttons

Select a preset station number (1 to 8).

F Tone controls

These controls are effective only for the sound from the main

speakers.

BASS

Used to increase or decrease the low frequency response.

The 0 position produces flat response.

TREBLE

Used to increase or decrease the high frequency response.

The 0 position produces flat response.

G BALANCE control

Adjusts the balance of the output volume to the left and right

speakers to compensate for sound imbalance caused by

speaker location or listening room conditions.

H FM/AM buttons

Press this button to switch the reception band to FM or AM.

I MEMORY (MAN’L/AUTO FM) button

When this button is pressed, the MEMORY indicator flashes for

about 5 seconds. During this period, select a desired preset

station number by pressing the corresponding preset station

number selector button to enter the displayed station into the

memory.

When this button is pressed and held for about 3 seconds, the

automatic preset tuning begins. (Refer to page 28 for details.)

J EDIT button

This button is used to exchange the places of two preset

stations with each other.

PHONES

DISPLAY PANEL

PRESET

kHz

MHz

MEMORY

SLEEP

TAPE 2 MONITOR

DIGITAL

STEREO

l00

ROOM 2 CONTROL

NORMAL WIDEPHANTOM

40 60

SPEAKERS

DSP

PRO LOGIC

DIGITAL

AUTO TUNING

SPEAKERS

ROOM 2

ENHANCED

324567 89

PRESET

kHz

MHz

MEMORY

AUTO

SLEEP

TAPE MONITOR

STEREO

ms dB

PRO LOGIC

ENHANCED

CONCERT

VIDEO

MONO

MOVIE

STADIUM

DISCO

ROCK CONCERT

CONCERT HALL

NORMAL

WIDE

PHANTOM

EFFECT OFF

l00

40 60

156970

324 A

RX-V592

RX-V692

K TUNING DOWN/UP button

Used for tuning. Press the “UP” side to tune in to higher

frequencies, and press the “DOWN” side to tune in to lower

frequencies.

L TUNING MODE (AUTO/MAN’L MONO) button

Press this button to switch the tuning mode to automatic or

manual. To select the automatic tuning mode, press this

button so that “AUTO (TUNING)” lights up on the display. To

select the manual tuning mode, press this button so that

“AUTO (TUNING)” goes off.

M DELAY/CENTER/REAR/SWFR and TIME/LEVEL +/–

buttons

Adjust the delay time (DELAY), the rear channel output level

(REAR), center channel output level (CENTER) and the output

level to the SUBWOOFER OUTPUT terminal (SWFR).

Select the item which you want to adjust by pressing the

DELAY/CENTER/REAR/SWFR button and adjust its time or

level by pressing the TIME/LEVEL +/– button.

N CENTER MODE button

Selects a center channel output mode (NORMAL, WIDE or

PHANTOM). (For details, refer to page 21.)

O VIDEO AUX terminals

Connect an auxiliary video or audio input source unit such as a

camcorder to these terminals. The source connected to these

terminals can be selected by the corresponding input selector

button.

* RX-V692 only

If the connected video unit has a S video output terminal,

connect it to the S VIDEO terminal to obtain a high resolution

picture.

English

1 Multi-information display

Displays various information, for example station frequency,

preset station number and name of selected input source.

2 MEMORY indicator

When the MEMORY button is pressed, this indicator flashes

for about 5 seconds. During this period, the displayed station

can be programmed to the memory by using the A/B/C/D/E

button and the preset station number selector buttons.

3 AUTO (TUNING) indicator

Lights up when this unit is in the automatic tuning mode.

4 TAPE MONITOR indicator

Lights up when the tape deck (or MD recorder etc.) is selected

as the input source by pressing the TAPE (MD) MON button.

5 STEREO indicator

Lights up when an FM stereo broadcast with sufficient signal

strength is received.

6 Signal-level meter

Indicates the signal level of the received station.

If multipath interference is detected, the indication decreases.

7 Center channel mode indicators

The name of a selected center channel mode lights up only

when a program which uses the Dolby Pro Logic Surround

decoder is selected.

8 DSP and PRO LOGIC indicators

RX-V692 only

“DSP” lights up when the built-in digital sound field processor

is on, and “ PRO LOGIC” lights up when the built-in Dolby

Pro Logic Surround decoder is on. Both indicators light up

when the digital sound field processor and the Dolby Pro Logic

Surround decoder are on.

9 SLEEP indicator

Lights up while the built-in SLEEP timer is functioning.

0 EFFECT OFF indicator RX-V592 only

Lights up if neither the digital sound field processor nor the

Dolby Pro Logic Surround decoder is on. In this state, sound

output is 2-channel stereo.

A DSP program indicators RX-V592 only

The name of a selected DSP program lights up when the built-

in digital sound field processor and/or the Dolby Pro Logic

Surround decoder is on.

Set to the “

∞

” position.

2 Turn the power on.

3 Select the main speakers to be used.

* If you use two main speaker systems, press both the A

and B switches.

Set to the “0” position.

Set to the “OFF ( )”.

SPEAKER BALANCE ADJUSTMENT

This procedure lets you adjust the sound output level balance between the main, center, and rear speakers using the built-in test

tone generator. When this adjustment is performed, the sound output level heard at the listening position will be the same from

each speaker. This is important for the best performance of the digital sound field processor and the Dolby Pro Logic Surround

decoder.

The adjustment of each speaker output level should be done at your listening position with the remote control transmitter.

Otherwise, the result may not be satisfactory.

SPEAKERS

OFF

BASS TREBLE

BALANCE

–dB

VOLUME

POWER

VCR

DVD/LD

V-AUX

PHONO

EFFECT

ON/OFF

TV/DBS

DIR

DISCSTOP

PRESET

A/B/C/D/E

PRO LOGIC ENHANCED

123

456

789

MOVIE

STADIUM

DISCO

MONO

VIDEO

CONCERT

ROCK HALL

TIME/LEVEL

DELAY

CENTER

REAR

SWFR

TEST

S EEP 2CH/6CH

+10

–dB

RX-V592

RX-V692

RX-V592

RX-V692

OFF

BASS

EXTENSION

TONE

BYPASS

BASS

EXTENSION

OFF

5 4

: Provided for RX-V692 only.

VCR

DVD/LD

V-AUX

PHONO

EFFECT

ON/OFF

TV/DBS

DIR

DISCSTOP

PRESET

A/B/C/D/E

PRO LOGIC ENHANCED

MOVIE THEATER

70 mm

123

456

789

SPORTS

STADIUM

DISCO

ROCK

JAZZ CLUB

CHURCH

HALL

TIME/LEVEL

DELAY

CENTER

REAR

SWFR

TEST

S EEP 2CH/6CH

+10

TEST

English

–dB

7 Select the center channel output mode suitable for your

speaker configuration.

(Refer to “SPEAKER CONFIGURATION” on page 7.)

On the feature of each mode, refer to the “Note” shown

below.

Note

In step 7, when you select a center channel output mode, note

the following.

For 5 speaker configuration)

NORMAL: Select this mode when you use a center speaker

that is smaller than the main speakers. In this

mode, the bass tone will be output from the main

speakers.

WIDE: Select this mode when you use the center speaker

approximately same sized as the main speakers.

For 4 speaker configuration)

PHANTOM: Select this mode when you do not use the center

speaker. The center sound will be output from the

left and right main speakers.

8 Turn up the volume.

You will hear a test tone (like pink noise) from the left main

speaker, then the center speaker, then the right main

speaker, and then the rear speakers, for about two seconds

each. The display changes as shown below.

* The test tone from the left rear speaker and the right

rear speaker will be heard at the same time.

9 Adjust the BALANCE control so that the effect sound

output level of the left main speaker and the right main

speaker are the same.

CENTER

MODE

NORMAL

WIDE

PHANTOM

BALANCE

ON/OFF

TIME/LEVEL

DELAY

CENTER

REAR

SWFR

TEST

SLEEP 2CH/6CH

MASTER VOLUME

VCR

OFF

SYSTEM

POWER

+10

REMOTE CONTROL

TRANSMITTER

CONTINUED

Main (L)

Main (R)

Center

Rear (L and R)

10 Adjust the sound output levels of the center

speaker and the rear speakers so that they

become almost as same as that of the main

speakers.

a) Press once or more so that “CENTER” or “REAR”

appears on the display.

* Select “CENTER” to adjust the output level of the

center speaker, and select “REAR” to adjust the

output level of the rear speakers.

b) Adjust its level.

* Pressing the + side raises and the – side lowers the

level.

11 Cancel the test tone.

Notes

●

Once you have completed these adjustments, you can

adjust whole sound level on your audio system by using

the VOLUME control (or the MASTER VOLUME keys on

the remote control transmitter) only.

●

If you use external power amplifiers, you may also use

their volume controls to achieve proper balance.

●

In step 10, if the center channel mode is in the

“PHANTOM” position, the sound output level of the center

speaker cannot be adjusted. This is because in this

mode, the center sound is automatically output from the

left and right main speakers.

V-AUX

PHONO

EFFECT

ON/OFF

PRO LOGIC ENHANCED

123

456

789

MOVIE

STADIUM

DISCO

MONO

VIDEO

CONCERT

ROCK HALL

TIME/LEVEL

DELAY

CENTER

REAR

SWFR

TEST

SLEEP 2CH/6CH

MASTER VOLUME

VCR

OFF

SYSTEM

POWER

+10

RX-V592

RX-V692

V-AUX

PHONO

EFFECT

ON/OFF

PRO LOGIC ENHANCED

MOVIE THEATER

70 mm

123

456

789

SPORTS

STADIUM

DISCO

ROCK

JAZZ CLUB

CHURCH

HALL

TIME/LEVEL

DELAY

CENTER

REAR

SWFR

TEST

SLEEP 2CH/6CH

MASTER VOLUME

VCR

OFF

SYSTEM

POWER

+10

MUTE

Disappears.

TEST

English

Set to the “

∞

” position.

2 Turn the power on.

3 Select the desired input source by using the input

selector buttons.

(For video sources, turn the TV/monitor ON.)

* The name of the selected input source will appear on

the display.

4 Select the main speakers to be used.

* If you use two main speaker systems, press both the A

and B switches.

5 Play the source. (For detailed information on the

tuning operation, refer to page 26.)

Adjust to the desired output level.

7 If desired, adjust the BASS, TREBLE, BALANCE

controls, etc. (refer to page 25) and use the digital

sound field processor. (Refer to page 32.)

Notes on using the input selector buttons

●

Note that pressing on each input selector button selects

the source which is connected to the corresponding input

terminals on the rear panel.

* To select the source connected to the VIDEO AUX

terminals on the front panel, press VIDEO AUX.

●

The selection of TAPE (MD) MON cannot be canceled by

pressing another input selector button. To cancel it, press

TAPE (MD) MON again so that “TAPE MONITOR”

disappears from the display.

When you select a button other than TAPE (MD) MON,

make sure that “TAPE MONITOR” is not illuminated on the

display.

●

If you select the input selector button for a video source

without canceling the selection of TAPE (MD) MON, the

playback result will be the video image from the video

source and the sound from the audio tape (or MD etc.).

●

Once you play a video source, its video image will not be

interrupted even if the input selector button for an audio

source is selected.

To turn off the power

Press the POWER switch again.

BASIC OPERATIONS

TO PLAY A SOURCE

–dB

VOLUME

SPEAKERS

OFF

–dB

VOLUME

VCR DVD

LDTV

DBS

VIDEO AUX

TAPE (MD) MON 2CH/6CH

POWER

1, 6

–dB

: Provided for RX-V692 only.

1 Select the source to be recorded.

2 Play the source and then turn the VOLUME control up

to confirm the input source. (For detailed information

on the tuning operations, refer to the page 26.)

3 Begin recording on the tape deck (or MD recorder etc.)

or VCR connected to this unit.

4 If the tape deck (or MD recorder etc.) is used for

recording, you can monitor the sounds being recorded

by pressing TAPE (MD) MON so that “TAPE

MONITOR” lights up on the display.

Notes

●

The settings of DSP and the VOLUME, BASS, TREBLE,

BALANCE controls and the BASS EXTENSION switch

have no effect on the material being recorded.

●

In step 1, do not make an input source selection so that

“6ch” appears on the display. Signals input to this unit’s

6CH DISCRETE INPUT DVD/LD TV/DBS terminals cannot

be recorded by a tape deck, MD recorder or VCR.

–dB

VOLUME

TO RECORD A SOURCE TO TAPE (OR MD)

–dB

1 4

VCR DVD

LDTV

DBS

VIDEO AUX

TAPE (MD) MON 2CH/6CH

TUNER

PHONO

To listen to a decoded source using Dolby

Digital (AC-3) by reproducing the signals input

to the 6CH DISCRETE INPUT DVD/LD TV/DBS

terminals of this unit.

In step 3, select TV/DBS or DVD/LD, and then press the

2CH/6CH button so that “6ch” appears on the display.

Discrete signals from the unit connected to the 6CH

DISCRETE INPUT DVD/LD TV/DBS terminals of this unit are

selected as the input signals.

To cancel it, press the 2CH/6CH button again or select another

input source.

Note for reproducing discrete signals with Dolby Digital

(AC-3) decoded:

Your speaker system must include a center speaker.

Your speaker system must include a subwoofer.

* Connect a subwoofer which has a built-in amplifier to the

SUBWOOFER OUTPUT terminal of this unit.

* You can do without using a subwoofer. If you do so, you

should make a setting for distributing signals at the LFE

channel to the right and left MAIN output terminals on the

Dolby Digital (AC-3) Decoder unit.

For details, refer to the owner’s manual for the Dolby

Digital (AC-3) Decoder unit.

Notes

●

When you switch to the “6CH” mode, the built-in Digital

Sound Field processor will not work and adjustment of delay

time cannot be made.

●

Switching this unit to the “6CH” mode will input no signal to

this unit if there is no connection to the 6CH DISCRETE

INPUT DVD/LD TV/DBS terminals of this unit.

VIDEO AUX

TAPE (MD) MON 2CH/6CH

TUNER

PHONO

2CH

6CH

RX-V592

RX-V692

English

Selecting the SPEAKER system

Because one or two speaker systems (as main speakers) can

be connected to this unit, the SPEAKERS switches allow you

to select speaker system A or B, or both at once.

Adjusting the BALANCE control

Adjust the balance of the output volume to the left and right

speakers to compensate for sound imbalance caused by

speaker location or listening room conditions.

Note

This control is effective only for the sound from the main

speakers.

Adjusting the BASS and TREBLE

controls

BASS : Turn this clockwise to increase (or counter-

clockwise to decrease) the low frequency

response.

TREBLE : Turn this clockwise to increase (or counter-

clockwise to decrease) the high frequency

response.

Note

These controls are effective only for the sound from the main

speakers.

Using the BASS EXTENSION switch

You can boost bass frequency response by setting this switch

to the “ON” position. This switch is effective only on the sound

from the main speakers.

Using the TONE BYPASS switch

RX-V692 only

Press this switch to revert instantly to the flat states of the

BASS and TREBLE controls without changing the setting of

these controls.

SPEAKERS

OFF

BALANCE

BASS TREBLE

OFF

BASS

EXTENSION

BYP

OFF

NSION

TONE

BYPASS

BASS

EXTENSION

OFF

RX-V592

RX-V692

1 Select the reception band (FM or AM) confirming it on

the display.

Tune to a desired station manually.

* To continue tuning search, press and hold the button.

1 Select the reception band (FM or AM) confirming it on

the display.

To tune to a higher frequency, press the right side once.

To tune to a lower frequency, press the left side once.

* If the station where tuning search stops is not the desired

one, press again.

* If the tuning search does not stop at the desired station

(because the signals of the station are weak), change to

the MANUAL TUNING method.

TUNING OPERATIONS

Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is

possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING).

Note

If you tune to an FM station manually, it is received in monaural

mode automatically to increase the signal quality.

AUTOMATIC TUNING MANUAL TUNING

TUNING

MODE

AUTO

MAN’L MONO

TUNING

MODE

AUTO

MAN’L MONO

DOWN

TUNING

DOWN

TUNING

AUTO TUNING

Turn “AUTO

(TUNING)” off.

FM AM

–dB

RX-V592

RX-V692

RX-V592

RX-V692

FM AM

RX-V592

RX-V692

AUTO

English

1 Tune to a desired station.

(Refer to the previous page for tuning procedure.)

2 Select a desired group (A – E) of preset stations

confirming it on the display.

4 Select a preset station number where you want to

program the station before “MEMORY” goes off from the

display.

* In the same way, program other stations to A2, A3 ... A8.

* You can program more stations to preset station numbers

on other groups in the same way by selecting other groups

in step 2.

11 Select the group of preset stations.

22 Select the preset station number.

Notes

• A new setting can be programmed in place of the former

one.

• For presets, the setting of the reception mode (stereo or

monaural) is stored along with the station frequency.

Memory back-up

The memory back-up circuit prevents the programmed data

from being lost even if the POWER switch is set off or the

power plug is disconnected from the AC outlet or the power is

cut due to temporary power failure. If, however, the power is

cut for more than one week, the memory may be erased. If

so, it can be re-programmed by simply following the PRESET

TUNING steps.

MANUAL PRESET TUNING

This unit can store station frequencies selected by tuning operation. With this function, you can recall any desired station by only

selecting the preset station number where it is stored. Up to 40 stations (8 stations x 5 groups) can be stored.

PRESET TUNING

To store stations

To recall a preset station

2, 11 34, 22

MAN’L

AUTO FM

MEMORY

PRESET

Flashes on and off

for about 5 seconds.

PRESET

MHz

STEREO

l00

ROOM 2 CONTROL

40 60

SPEAKERS

AUTO TUNING

SPEAKERS

ROOM 2

Shows the displayed station has been

programmed to A1.

–dB

2 3 4 5 6 7 8

RX-V592

RX-V692

PRESET

MHz

AUTO

STEREO

l00

40 60

To tune to higher frequencies, press right side once.

To tune to lower frequencies, press left side once.

* If the TUNING button is not pressed, in a while, the

automatic preset tuning begins automatically toward higher

frequencies.

The automatic preset tuning begins from the frequency

currently displayed. Received stations are programmed to

A1, A2 ... A8 sequentially.

* If more than 8 stations are received, they are also

programmed to the preset station numbers on other groups

(B, C, D and E) in that order.

If you want to store the first station received by the

automatic preset tuning to a desired preset station

number.

If, for example, you want to store the first received station to

C5, select “C5” by using the A/B/C/D/E button and the preset

station number selector buttons after pressing the MEMORY

button in step 2. Then press the TUNING button. The first

received station is stored to C5, and next stations to C6, C7 ...

sequentially.

If stations are stored up to E8, the automatic preset tuning is

finished automatically.

When the automatic preset tuning is finished

The display shows the frequency of the last preset station.

Check the contents and the number of preset stations by

following the procedure of the section “To recall a preset

station” on page 27.

To recall a preset station

Simply follow the procedure of the section “To recall a preset

station” on page 27.

Notes

●

You can replace a preset station by another FM or AM

station manually by simply following the procedure of the

section “To store stations” on page 27.

●

If the number of received stations is not enough to be stored

up to E8, the search is finished automatically after searching

all frequencies.

●

With this function, only FM stations with sufficient signal

strength are stored automatically. If the station you want to

program is weak in signal strength, tune to it in monaural

manually and program it by following the procedure of the

section “To store stations” on page 27.

AUTOMATIC PRESET TUNING

You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic

tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the

manual preset tuning method on page 27.

To store stations

Press and hold for

about 3 seconds.

MAN’L

AUTO FM

MEMORY

–dB

1 32

Flashes.

DOWN

TUNING

PRESET

MEMORY

AUTO TUNING

RX-V592

RX-V692

RX-V592

RX-V692

PRESET

MEMORY

AUTO

English

EXCHANGING PRESET STATIONS

You can exchange the places of two preset stations with each other as shown below.

Example)

If you want to shift the preset station on E1 to A5, and vice

versa.

1 Recall the preset station on E1 (by following the method

of “To recall a preset station” on page 27).

3 Next, recall the preset station on A5 by following the

same method with step 1.

Shows the exchange of stations is completed.

Flashes.

EDIT

MEMORY

PRESET

MEMORY

PRESET

2, 4

–dB

RX-V592

RX-V692

Brief Overview of Digital Sound Field Programs

The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of

these are precise digital recreations of actual acoustic environments. The data for these sound fields was recorded at actual

locations using sophisticated sound field measurement equipment.

Note

The channel level balance between the left and right rear effect speakers may vary depending on the sound field you are

listening to. This is due to the fact that most of these sound field recreations are actual acoustic environments.

PROGRAM FEATURE

This program is used for playback of sources encoded with Dolby Surround.

PRO LOGIC The application of a sophisticated digital signal processing system reduces crosstalk and directs or steers

the sound source more smoothly and precisely, as compared to conventional types.

This program is also used for playback of sources encoded with Dolby Surround.

PRO LOGIC

Enhancing the “Normal” Dolby Pro Logic, the DSP technology simulates the multi-surround speaker

ENHANCED

systems of a 35 mm movie theater. This effect creates a wide surround sound field, and expands the

sound stage with an improved presence image. This program is used for musical based movies, as well as

drama and comedy based movies.

STADIUM

This program gives you long delays between direct sounds and effect sounds, and extraordinarily

spacious feel of a large stadium.

DISCO

This program recreates the acoustic environment of a lively disco in the heart of a very lively city. The

sound is dense and highly concentrated. It is also characterized by a high-energy, “immediate” sound.

ROCK CONCERT This program is ideally suited for rock music. You will experience a very dynamic or lively sound field.

CONCERT HALL

In this program, the center will appear to be deep behind the main speakers, creating an expansive large

hall ambience. Orchestra and opera music are suited for this sound field.

USING DIGITAL SOUND FIELD PROCESSOR (DSP)

This unit incorporates a sophisticated, multi-program digital sound field processor. The processor allows you to electronically expand

and change the shape of the audio sound field from both audio and video sources, creating a theater-like experience in your

listening room. You can create an excellent audio sound field by selecting a suitable sound field program (this will, of course, depend

on what you will be listening to), and adding desired adjustments.

In addition, this unit incorporates a Dolby Pro Logic Surround decoder for multi-channel sound reproduction of sources encoded with

Dolby Surround. The operation of the Dolby Pro Logic Surround decoder can be controlled by selecting a corresponding DSP

program including a combined operation of the Yamaha DSP and the Dolby Pro Logic Surround.

English

PROGRAM FEATURE

70 mm

This program is effective for playback of sources encoded with Dolby Surround.

MOVIE THEATER

The Yamaha DSP technology is ideally combined with the Dolby Pro Logic to present you incredible

listening experience of the 70 mm film movie theater. This program is ideal for precisely reproducing the

sound design of the newest movies. The sound field is made according to the design of the newest movie

theaters, so the reverberations of the sound field itself are restrained as much as possible. The three

dimensional feeling of the sound field is emphasized, and dialog is precisely oriented on the screen. You can

enjoy watching Sci-Fi, adventure movies, etc. with this program.

TV SPORTS

This program is furnished with a tight sound field in which the sound will not spread excessively on the front

side, but the rear surround side produces a dynamic sound expansion. This program is the most suitable for

sports programs encoded with Dolby Surround.

JAZZ CLUB This is a small, cozy jazz club with a low ceiling. The sound is very close and intimate.

CHURCH

This program recreates the acoustic environment of a big church with a high pointed dome and columns along

the sides. This interior produces very long reverberations.

PROGRAM FEATURE

CONCERT VIDEO

This program is effective for music videos and gives excellent depth and clarity for vocals. For opera, the

orchestra and stage are ideally recreated, letting you feel as if you were in an actual concert hall.

MONO MOVIE

This program is designed specifically to enhance mono source programs. Compared to a strictly mono

setting, the sound image created in this mode is wider and slightly forward of the speaker pair, lending an

immediacy to the overall sound. It is particularly effective when used with old mono movies, news

broadcasts and dialog.

RX-V692 only

RX-V592 only

1 Follow steps 1 – 6 shown in “BASIC OPERATIONS” on

page 23.

2 Select the desired program that is suitable for the

source.

The selected program name is shown on the display.

3 If desired, adjust the delay time and the output level of

each speaker. (For details, refer to the corresponding

descriptions on page 33 and 34.)

Notes

●

Program selection can be made to individual input sources.

Once you select a program, it is linked with the input source

selected at that time. So, when you select the input source

next time, the same program is automatically called.

●

If you prefer to cancel the DSP, press the EFFECT button.

The sound will be the normal 2-channel stereo without

surround sound effect.

●

RX-V692 only

When STADIUM, DISCO, ROCK CONCERT, JAZZ CLUB,

CHURCH or CONCERT HALL is selected, no sound is

heard from the center speaker.

RX-V592 only

When CONCERT VIDEO, MONO MOVIE, DISCO,

STADIUM, ROCK CONCERT or CONCERT HALL is

selected, no sound is heard from the center speaker.

●

When a monaural sound source is played with DOLBY PRO

LOGIC or DOLBY PRO LOGIC ENHANCED, no sound is

heard from the main speakers and the rear speakers.

Sound is heard only from the center speaker. However, if

the center channel mode is in PHANTOM, the main

speakers output the sound of the center channel.

●

When this unit’s Dolby Pro Logic Surround decoder is used,

if the main-source sound is considerably altered by

overadjustment of the BASS or TREBLE control, the

relationship between the center and rear channels may

produce an unnatural effect.

To play a source with the digital sound field processor

PRO LOGIC

–dB

VCR

DVD/LD

V-AUX

PHONO

EFFECT

ON/OFF

TV/DBS

DIR

DISCSTOP

PRESET

A/B/C/D/E

PRO LOGIC ENHANCED

1 2 3

4 5 6

7 8 9

MOVIE

STADIUM

DISCO

MONO

VIDEO

CONCERT

ROCK HALL

TIME/LEVEL

DELAY

CENTER

REAR

SWFR

TEST

SLEEP 2CH/6CH

+10

RX-V592

RX-V692

: Provided for RX-V692 only.

VCR

DVD/LD

V-AUX

PHONO

EFFECT

ON/OFF

TV/DBS

DIR

DISCSTOP

PRESET

A/B/C/D/E

PRO LOGIC ENHANCED

MOVIE THEATER

70 mm

1 2 3

4 5 6

7 8 9

SPORTS

STADIUM

DISCO

ROCK

JAZZ CLUB

CHURCH

HALL

TIME/LEVEL

DELAY

CENTER

REAR

SWFR

TEST

SLEEP 2CH/6CH

+10

RX-V592

RX-V692

PRO LOGIC

ENHANCED

WIDE

PRO LOGIC

English

If desired, you can adjust the sound output level of the center

speaker even if the output level is already set in “SPEAKER

BALANCE ADJUSTMENT” on page 22.

1 Press once or more so that “CENTER” appears on the

display.

2 By continuously pressing the “+” or “–” side of the

TIME/LEVEL button, the level value changes continuously.

The value stops changing momentarily at the preset point

(0 dB).

Control range: MIN, –20 to +10 dB

Notes

●

RX-V692 only

This adjustment can be made only when the digital sound

field program DOLBY PRO LOGIC, DOLBY PRO LOGIC

ENHANCED, 70 mm MOVIE THEATER or TV SPORTS is

selected, or the “6CH” input source mode is selected.

RX-V592 only

This adjustment can be made only when the digital sound

field program DOLBY PRO LOGIC or DOLBY PRO LOGIC

ENHANCED is selected, or the “6CH” input source mode is

selected.

●

Once the output level is adjusted, the level value will be the

same in all the digital sound field programs mentioned

above.

Adjustment of the CENTER LEVEL

TIME

LEVEL

DELAY/CENTER

/REAR/SWFR

Adjustable

Adjustment of the REAR LEVEL

If desired, you can adjust the sound output level of the rear

speakers even if the output level is already set in “SPEAKER

BALANCE ADJUSTMENT” on page 22.

1 Press once or more so that “REAR” appears on the display.

2 By continuously pressing the “+” or “–” side of the

TIME/LEVEL button, the level value changes continuously.

The value stops changing momentarily at the preset point

(0 dB).

Control range: MIN, –20 to +10 dB

Notes

●

This adjustment can be made only when the built-in digital

sound field processor is on, or the “6CH” input source mode

is selected.

●

Once the output level is adjusted, the level value will be the

same in all the digital sound field programs.

TIME

LEVEL

DELAY/CENTER

/REAR/SWFR

Adjustable

Adjustment of DELAY TIME

You can adjust the time difference between the beginning of

the sound from the main speakers and the beginning of the

effect sound from the rear speakers.

The larger the value, the later the effect sound is generated.

This adjustment can be made to all programs individually.

PRO LOGIC : from 15 to 30 milliseconds

(Preset value: 20 milliseconds)

PRO LOGIC : from 15 to 30 milliseconds

ENHANCED (Preset value: 20 milliseconds)

70 mm MOVIE

: from 15 to 30 milliseconds

THEATER (Preset value: 17 milliseconds)

TV SPORTS : from 1 to 50 milliseconds

(Preset value: 20 milliseconds)

STADIUM : from 1 to 50 milliseconds

(Preset value: 45 milliseconds)

DISCO : from 1 to 50 milliseconds

(Preset value: 14 milliseconds)

ROCK CONCERT : from 1 to 50 milliseconds

(Preset value: 22 milliseconds)

JAZZ CLUB : from 1 to 50 milliseconds

(Preset value: 26 milliseconds)

CHURCH : from 1 to 50 milliseconds

(Preset value: 40 milliseconds)

CONCERT HALL : from 1 to 50 milliseconds

(Preset value: 30 milliseconds)

PRO LOGIC : from 15 to 30 milliseconds

(Preset value: 20 milliseconds)

PRO LOGIC : from 15 to 30 milliseconds

ENHANCED (Preset value: 20 milliseconds)

CONCERT VIDEO : from 1 to 100 milliseconds

(Preset value: 28 milliseconds)

MONO MOVIE : from 1 to 100 milliseconds

(Preset value: 20 milliseconds)

STADIUM : from 1 to 50 milliseconds

(Preset value: 45 milliseconds)

DISCO : from 1 to 100 milliseconds

(Preset value: 14 milliseconds)

ROCK CONCERT : from 1 to 100 milliseconds

(Preset value: 17 milliseconds)

CONCERT HALL : from 1 to 100 milliseconds

(Preset value: 30 milliseconds)

1 Press once or more so that “DELAY” appears on the

display.

2 By continuously pressing the “+” or “–” side of the

TIME/LEVEL button, the value changes continuously.

The value stops changing momentarily at the preset point.

Notes

●

Adding too much delay will cause an unnatural effect with

some sources.

●

When the TIME/LEVEL button is pressed, sound is

momentarily interrupted.

Note

The values of the delay time, center level and rear level you set

the last time will remain memorized even when the power of

this unit is off.

However, if the power cord is kept disconnected for more than

one week, these values will be automatically changed back to

the original factory settings.

TIME

LEVEL

DELAY/CENTER

/REAR/SWFR

Adjustable

DSP

RX-V692

RX-V592

RX-V692

DSP

RX-V592

RX-V692

English

Whenever the SLEEP key is pressed, the SLEEP time will

change as follows.

After a while, the display returns to the indication before

the SLEEP timer is set.

2 The unit will be turned off automatically at the selected

SLEEP time.

SETTING THE SLEEP TIMER

If you use the SLEEP timer of this unit, you can make this unit turn off automatically. When you are going to sleep while enjoying a

broadcast or other desired input source, this timer function is helpful.

Notes

●

The SLEEP timer can be controlled only with the remote control transmitter.

●

The components on which the SLEEP timer is effective are the sources connected to the SWITCHED AC OUTLET(S) on the rear

panel of this unit.

To set the SLEEP time

Press once or more to select the desired

SLEEP time.

Indicates the SLEEP time.

Lights up.

To cancel the selected SLEEP time

Press once or more so that “SLEEP OFF” appears on the

display. (It will soon disappear and the “SLEEP” indicator will

go off from the display.)

Note

The SLEEP timer setting can also be canceled by turning off

the power with the POWER switch or disconnecting the power

plug of this unit from the AC outlet.

SLEEP

Indicates the SLEEP time.

Lights up.

120 90 60 30

The SLEEP timer is off (OFF).

(The state before the SLEEP key

is pressed.)

(Minutes)

SLEEP

RX-V592

RX-V692

SLEEP

BASIC OPERATIONS (When the lid is open)

The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit. If the

CD player, tape deck, LD player etc. connected to this unit are YAMAHA components designed for remote control compatibility, then

this remote control transmitter will also control various functions of each component.

* For basic operations, use the remote control transmitter with the lid open.

NAMES OF KEYS AND THEIR FUNCTIONS

TAPE

A/B

REC/PAUSE

TUNER

VCR

DVD/LD

V-AUX

PHONO

EFFECT

ON/OFF

TV/DBS

DIR

DISCSTOP

TRANSMIT

/LEARN

LEARNCLEAR MACRO

PRESET

A/B/C/D/E

PRO LOGIC ENHANCED

MOVIE THEATER

70 mm

1 2 3

SPORTS

STADIUM

DISCO

4 5 6

ROCK

JAZZ CLUB

CHURCH

7 8 9

HALL

TIME/LEVEL

DELAY

CENTER

REAR

SWFR

TEST

SLEEP 2CH/6CH

MASTER VOLUME

VCR

OFF

SYSTEM

POWER

+10

MUTE

REMOTE CONTROL

TRANSMITTER

MACROQUICK

OFFSLOW

REMOTE CONTROL TRANSMITTER

The illustration is of remote control transmitter for the RX-V692.

●

RX-V692 and RX-V592 differ in some of the DSP programs (4).

●

RX-V592 does not have the MUTE key (A).

Lid is opened. Side panel

English

1 Tape deck keys

Controls tape deck.

(The A/B/C switch (

F) should be set to the “A” position.)

* DIR A, B and A/B are applicable only to double

cassette tape deck.

* For a single cassette deck with automatic reverse

function, pressing DIR A will reverse the direction of

tape running.

2 CD/LD player keys

Controls compact disc player or LD player.

(To control compact disc player, set the A/B/C switch (

F) to

the “A” position. To control LD player, set the A/B/C switch

(

F) to the “C” position.)

* DISC is applicable only to compact disc changer.

* STOP is applicable only to LD player.

3 Tuner keys

Controls tuner.

(The A/B/C switch (

F) should be set to the “A” position.)

+: Selects higher preset station number.

–: Selects lower preset station number.

A/B/C/D/E: Selects the group (A – E) of preset station

numbers.

4 DSP program selector keys

Selects a DSP program when the built-in digital sound field

processor (including the Dolby Pro Logic Surround decoder) is

on.

* RX-V592 only

The functions on “9” and “0” are useless.

5 TEST key

Used for speaker balance adjustment. (For details, refer to

page 20–22.)

6 SLEEP timer key

This key is used to turn the built-in SLEEP timer on and off,

and to set the SLEEP time. (See page 35 for details.)

7 2CH/6CH selector key

When the TV/DBS or DVD/LD input source is selected,

pressing this key switches the input signals between 2 channel

stereo signals and 6 channel discrete signals. When switched

to “6CH”, discrete signals from the unit connected to the 6CH

DISCRETE INPUT DVD/LD TV/DBS terminals of this unit are

selected as the input signals.

8 SYSTEM POWER and OFF keys

Pressing the SYSTEM POWER key turns the power of this unit

on and pressing the OFF key turns the power off.

* (Except U.S.A. and Canada models)

While the power is on, pressing these keys switches the unit

from the power-on mode to the standby mode, and vice

versa. (In the standby mode, the standby mode indicator on

the front panel is illuminated.)

9 RESET button

This button is inside the battery compartment.

Press this button to “reset” the internal microcomputer which

controls remote control operations. Microcomputer “reset” is

necessary when the remote control freezes.

* Pressing the RESET button will not erase learned

functions.

0 MASTER VOLUME (up) and (down) keys

Turns the volume level up and down.

A MUTE key RX-V692 only

When pressed, this key mutes the volume level. To resume the

original volume level, press this key again.

While muting, the indicator on the VOLUME control flashes

continuously.

B DELAY/CENTER/REAR/SWFR selector ( / ) and

TIME/LEVEL +/– keys

Adjust the delay time (DELAY), the rear channel output level

(REAR), center channel output level (CENTER) and the output

level to the SUBWOOFER OUTPUT terminal (SWFR).

Select the item which you want to adjust by pressing the or

key and adjust its time or level by pressing the + or – key.

C EFFECT ON/OFF key

Switches on/off the digital sound field processor (including the

Dolby Pro Logic Surround decoder).

D Input selector keys

Selects input source.

E A/B/C indicators

The position (A, B or C) selected by the A/B/C switch is shown

in red.

F A/B/C switch

This switch must be used only when the lid of the remote

control transmitter is open. (This switch will not function when

the lid is closed.)

Normally, set this switch to the “A” position. When controlling a

Yamaha LD player by using the CD/LD player keys (

2), set

this switch to the “C” position.

G TRANSMIT/LEARN indicator

Lights up when the remote control transmitter is transmitting

infrared signals (when a command key is pressed).

Note

When using the keys to control Yamaha components,

identify them with your component’s keys. If these keys

are identical, their functions will be the same. For each key

function, refer to the corresponding instruction in your

component’s manual.

RESET button

LEARNING NEW CONTROL FUNCTIONS (When the lid is open)

This is a learning remote control transmitter. The shaded keys in the illustration shown below can be programmed to “learn”

control functions from other remote control transmitters. By learning key-functions from other remote control transmitter, this unit can

then be used in place of one or more other remote control transmitters, thus making operation of your various audio and video

components more convenient.

Some of the “learning-capable” keys are originally empty and others have already been preset with functions to control this unit and

other Yamaha components. You can store new functions to them (in place of preset functions) as desired.

* See page 43 for the learning method.

* See page 45 for clearing a learned function (or all learned functions).

Note

If the memory capacity of the remote control transmitter becomes full, no further learning is possible even if some learning-capable

keys are not occupied with new functions. If, for example, you store Yamaha codes only into this remote control transmitter, up to

about 20 functions can be stored. Store new functions to the learnable-capable keys which are useful for you.

TAPE

TUNER

VCR

DVD/LD

V-AUX

PHONO

EFFECT

ON/OFF

TV/DBS

TRANSMIT

/LEARN

LEARNCLEAR MACRO

TIME/LEVEL

DELAY

CENTER

REAR

SWFR

SLEEP 2CH/6CH

MASTER VOLUME

VCR

OFF

SYSTEM

POWER

MUTE

REMOTE CONTROL

TRANSMITTER

A/B

REC/PAUSE

DIR

DISCSTOP

PRESET

A/B/C/D/E

PRO LOGIC ENHANCED

MOVIE THEATER

70 mm

1 2 3

SPORTS

STADIUM

DISCO

4 5 6

ROCK

JAZZ CLUB

CHURCH

7 8 9

HALL TEST

+10

A/B/C switch

Keys which can have three functions (1, 2, 3, 4)

In the “Learning-capable” keys, the keys numbered 1–4 in the

illustration at left can have three functions. This is because they

have three memory areas (A, B and C). (One function per area.)

You can store new functions into the area B and C, and use three

functions on a key by switching the memory areas with the A/B/C

switch. (Area A cannot learn a new function.)

To use these keys:

1. Before using a key, select the area A, B or C of the key on which

the function you want to use is stored by using the A/B/C switch.

2. Press the key.

The original factory settings of these keys are as follows.

Preset with

functions for

controlling a

Yamaha tape deck.

Preset with

functions for

controlling a

Yamaha CD player.

(STOP is empty.)

Preset with

functions for

controlling

the built-in tuner.

Preset as the DSP

program selector

keys and the TEST

key.

Empty

Preset as the DSP

program selector

keys and the TEST

key.

Empty

Preset with

functions for

controlling a

Yamaha LD player.

(DISC is empty.)

Empty

Preset as the DSP

program selector

keys and the TEST

key.

The position of A/B/C switch

: “+10” is empty.

For RX-V592, the functions on “9” and “0” are useless.

Note

The area A of all keys cannot learn new functions. To store new

functions to these keys, store them onto the area B or C.

Empty keys (1, 2)

These are empty keys. Each key can learn a function from another

remote control transmitter.

For example, the TV key is useful for storing the function of your

TV’s power switch, and the VCR key can be used for your VCR’s

power switch.

Lid is open.

: These buttons are used for learning a new function

or clearing a learned function (or all learned

functions). See page 43–45 for details.

(RX-V692)

English

TAPE

TUNER

VCR

DVD/LD

V-AUX

PHONO

EFFECT

ON/OFF

TV/DBS

DIR

TRANSMIT

/LEARN

LEARNCLEAR MACRO

PRESET

A/B/C/D/E

PRO LOGIC ENHANCED

MOVIE THEATER

70 mm

1 2 3

SPORTS

STADIUM

DISCO

4 5 6

ROCK

JAZZ CLUB

CHURCH

7 8 9

HALL

TIME/LEVEL

DELAY

CENTER

REAR

SWFR

TEST

SLEEP 2CH/6CH

MASTER VOLUME

VCR

OFF

SYSTEM

POWER

+10

MUTE

REMOTE CONTROL

TRANSMITTER

REMOTE CONTROL

TRANSMITTER

TAPE

TUNER

VCR

DVD/LD

V-AUX

PHONO

TV/DBS

VCR

OFF

SYSTEM

POWER

MUTE

MASTER

VOLUME

OPERATION

CONTROL

EFFECT

TRANSMIT

DISCSTOP

A/B

REC/PAUSE

(+10)

Input selector keys

OPERATION CONTROL keys

Lid is closed.

Note

If a key which has a preset function learns a new function, the

preset function will not be deleted, but disabled. When the

learned function is cleared, the preset function is restored. (For

information on clearing a learned function, refer to page 45.)

About the marks shown on the remote control

transmitter

The marks on the remote control transmitter signify functions of

keys, input sources, etc.

Examples)

(tape): Shows tape deck, VCR, etc.

(disc): Shows CD player, LD player, etc.

(radio wave): Shows tuner, TV/BS tuner, etc.

These marks are helpful for storing new functions.

Examples)

• The area B of keys 1 is suitable for storing functions to

control your VCR.

• The area B of keys 3 is suitable for storing functions to

control your TV/BS tuner.

USING OPERATION CONTROL KEYS (When the lid is closed)

When the lid of the remote control transmitter is closed, you can easily operate Yamaha components including learned functions by

using the OPERATION CONTROL keys.

: These keys are originally empty. If these keys have learned functions, pressing them executes those learned functions.

(RX-V692)

When the lid is closed, the OPERATION CONTROL keys

substitute for the keys numbered

1, 2, 3 and the (+10)

key on the left illustration. To use these keys, you do not have

to switch the A/B/C switch. The functions which the

OPERATION CONTROL keys carry out are determined by

which input selector key was pressed before you used the

OPERATION CONTROL keys.

Note

When the lid is closed, the EFFECT, MASTER VOLUME,

MUTE (RX-V692 only), TV and VCR keys will function in the

same way as when the lid is open.

* If the MACRO switch on the side of the remote control

transmitter is set to “OFF”, when the lid is closed, the

SYSTEM POWER and OFF keys also will function in the

same way as when the lid is open.

Examples of operations controlled by using the

OPERATION CONTROL keys

To operate a Yamaha CD player

1. Press the “CD” input selector key.

2. Use the OPERATION CONTROL keys. (They carry out the

functions in area A of keys

2.)

To operate your VCR

1. Press the “VCR” input selector key.

2. Use the OPERATION CONTROL keys. (They carry out the

functions in area B of keys

1. This area is originally preset

with no function. You must store the functions related to

controlling the VCR in area B of keys

1 beforehand.)

Selected input selector

Key functions which the OPERATION CONTROL keys carry out

Functions in area A of keys

1 (except REC/PAUSE, A/B, DIR A and B)

Functions in area A of keys

2 (except STOP, DISC, and )

Functions in area A of keys

3 and (+10)

Functions in area B of keys

1 (except REC/PAUSE, A/B, DIR A and B)

Functions in area B of keys

2 (except STOP, DISC, and )

Functions in area B of keys

3 and (+10)

Functions in area C of keys

1 (except REC/PAUSE, A/B, DIR A and B)

Functions in area C of keys

2 (except STOP, DISC, and )

Functions in area C of keys

3 and (+10)

Notes

• If the OPERATION CONTROL keys substitute for keys

which has no function (empty), no command is carried out.

According to your plan, store functions from other remote

control transmitters into an empty area of those keys. (Refer

to page 43 for the learning method.)

• While playing an audio/video unit, if you want to operate

another unit by using the remote control transmitter (for

example, if you want to rewind a tape on your VCR while

listening to a CD), you should open the lid of the remote

control transmitter and use the A/B/C switch and the

corresponding keys.

(If you press an input selector key with the lid closed to

change the functions of the OPERATION CONTROL keys to

the functions for controlling a VCR, the input of currently

playing CD source is canceled.)

See the table below for a combination of an input selector key and key functions which the OPERATION CONTROL keys carry out.

(Also, refer to the table on page 38.)

Pressing the “V-AUX” or “PHONO” input selector key has no effect on the OPERATION CONTROL keys.

TAPE

TUNER

VCR

DVD/LD

TV/DBS

OPERATION

CONTROL

Play

Skip to

previous track

Skip to next

track

Pause or Stop

OPERATION

CONTROL

Play

Rewind Fast forward

Pause or Stop

English

REMOTE CONTROL

TRANSMITTER

TAPE

TUNER

VCR

DVD/LD

V-AUX

PHONO

TV/DBS

VCR

OFF

SYSTEM

POWER

MUTE

MASTER

VOLUME

OPERATION

CONTROL

EFFECT

TRANSMIT

MACROQUICK

OFFSLOW

TAPE

TUNER

VCR

DVD/LD

V-AUX

PHONO

EFFECT

ON/OFF

TV/DBS

DIR

TRANSMIT

/LEARN

LEARNCLEAR MACRO

PRESET

A/B/C/D/E

PRO LOGIC ENHANCED

MOVIE THEATER

70 mm

1 2 3

SPORTS

STADIUM

DISCO

4 5 6

ROCK

JAZZ CLUB

CHURCH

7 8 9

HALL

TIME/LEVEL

DELAY

CENTER

REAR

SWFR

TEST

SLEEP 2CH/6CH

MASTER VOLUME

VCR

OFF

SYSTEM

POWER

+10

MUTE

REMOTE CONTROL

TRANSMITTER

DISCSTOP

A/B

REC/PAUSE

Preset macro keys

MACRO OPERATIONS (When the lid is closed)

“Macro” is a command which defines a sequence of several

operations.

The keys shown in the illustrations below (as preset macro

keys) are also preset with macros, in addition to individual

functions.

Each macro key is preset so that simply pressing it alone will

carry out several functions of other keys on this remote control

transmitter sequentially. (To know what key functions are

sequentially carried out by pressing each preset macro key,

see the next page.)

Macros can be used only when the lid is closed and the

MACRO switch is set to “SLOW” or “QUICK”. (If “OFF” is

selected, no macro will function even if the lid is closed.)

Preset macro keys are originally preset with macros. If you

prefer, however, you can change the contents of a macro key

by storing a desired series of functions on it. You can store up

to seven functions onto a macro key. (See page 44 for the

learning method.)

Setting the MACRO switch

OFF: In this position, no macro will function even if the lid of

remote control transmitter is closed.

QUICK: In this position, when a macro key is pressed, each

command is transmitted at 0.5 second intervals.

SLOW: In this position, when a macro key is pressed, each

command is transmitted at 3 second intervals.

Lid is closed.

(Set the MACRO switch to

“QUICK” or “SLOW”.)

MACRO switch

(RX-V692) (RX-V692)

Macro key

1st

(Turning the power of this unit on)

2nd

(Selecting an input source)

3rd

(Playing a source)

“ ” on area A of keys

“ ” on area A of keys 2

–

“ ” on area B of keys

“ ” on area B of keys 2

–

“ ” on area C of keys

“ ” on area C of keys 2

–

Function of the key (and area) which operates when a macro key is pressed

Macro key

1st 2nd

–

3rd

–

Function of the key which operates when a macro key is pressed

Preset macro keys and the key functions which they carry out sequentially are as follows. (Also, refer to the table on page 38.)

Notes

• A key in which no function is stored will carry out no

command.

• If it occurs that this unit will not receive the second command

because the internal operation of the first command takes a

long time, set the MACRO switch to the “SLOW” position, or

add no function or repeat the same command between the

first command and the next command.

• If you will program the power on/off switching function of TV,

VCR, etc. as part of a macro sequence, note that it switches

the current mode to the other (“on” to “off”, or “off” to “on”).

For example, when you press the macro key, if the power of

TV, VCR, etc. is already on, the power will be turned off

even though you may not want it to do so.

• Once you press a macro key, this unit will not receive the

command of another key (even if it is pressed) until this unit

finishes carrying out all commands of the macro key. Take

notice of this especially when the MACRO switch is in the

“SLOW” position.

• Once you press a macro key, you must keep the remote

control transmitter directed at the main unit’s remote control

sensor until the remote control transmitter finishes

transmitting all command signals of the macro key.

• You can use the OPERATION CONTROL keys also while

using the macro functions.

TAPE

TUNER

VCR

DVD/LD

V-AUX

PHONO

TV/DBS

TAPE

TUNER

VCR

DVD/LD

V-AUX

PHONO

TV/DBS

SYSTEM

POWER

SYSTEM

POWER

OFF

SYSTEM

POWER

OFF

VCR

English

LEARNING A NEW FUNCTION

1 Place this remote control transmitter and the other

remote control transmitter so that they face each other.

* If there is no operation for about 30 seconds after the

LEARN button is pressed, the TRANSMIT/LEARN indicator

flashes rapidly and the current mode is canceled. If this

occurs, repeat this step.

3 If necessary, select the memory area by using the A/B/C

switch on the side panel of the remote control

transmitter.

4 Press the key on this remote control transmitter in which

you will store a new function.

* If a key which cannot learn another function is pressed, the

TRANSMIT/LEARN indicator flashes rapidly and the current

mode is canceled. If this occurs, repeat this step.

* If there is no operation for about 30 seconds after a key is

pressed, the TRANSMIT/LEARN indicator flashes rapidly

and the mode before you began learning operations is

restored. If this occurs, restart from step 2.

5 Press and hold the key (on the other remote control

transmitter) which has the function you want to store.

* When learning is finished, the TRANSMIT/LEARN indicator

stops lighting and then begins flashing slowly.

* If a signal is not successfully received, the

TRANSMIT/LEARN indicator flashes rapidly and the mode

prior to step 4 is restored. If this occurs, restart from step 4.

* If memory capacity is full, the TRANSMIT/LEARN indicator

flashes rapidly to show you that learning is impossible, and

then the mode before you began learning operations is

restored.

6 Repeat step 3–5 to store more functions.

7 When you finish the learning operation, press the

LEARN button.

Notes

●

Newly learned functions will replace previously learned

functions.

●

If there is no more room in the memory area for a function to

be learned, the TRANSMIT/LEARN indicator will flash

rapidly. In this case, even if some keys are not occupied

with functions from other remote control transmitters, no

further learning is possible.

●

If the lid is closed while learning and about 5 seconds pass,

the TRANSMIT/LEARN indicator flashes rapidly and the

mode before you began learning operations is restored. If

this occurs, restart from step 2. However, if the lid is opened

within 5 seconds, the mode before the lid was closed is

restored.

●

There may occasionally be instances in which, due to the

signal-coding and modulation employed by the other remote

control transmitter, this remote control transmitter will not be

able to “learn” its signals.

V-AUX

PHONO

EFFECT

ON/OFF

1 2 3

SPORTS

STADIUM

DISCO

4 5 6

JAZZ CLUB

CHURCH

TEST

V-AUX

PHONO

EFFECT

ON/OFF

1 2 3

SPORTS

STADIUM

DISCO

4 5 6

ROCK

JAZZ CLUB

CHURCH

7 8 9

HALL

EVEL

TEST

LUME

+10

Lights up.

V-AUX

PHONO

EFFECT

ON/OFF

1 2 3

SPORTS

STADIUM

DISCO

4 5 6

JAZZ CLUB

CHURCH

8 9

TEST

This remote control

transmitter

Other remote

control transmitter

About 5–10 cm

(2–4 in.)

TRANSMIT

/LEARN

LEARNCLEAR MACRO

Flashes slowly.

(Press by using the point of

a mechanical pencil, etc.)

LEARNCLEAR MACRO

* If there is no operation for about 30 seconds after the

MACRO button is pressed, the TRANSMIT/LEARN

indicator flashes rapidly and the mode before you pressed

the MACRO button is restored. If this occurs, press the

MACRO button again.

2 Press a preset macro key on which you want to make a

new macro.

* If a key other than a preset macro key is pressed, the

TRANSMIT/LEARN indicator flashes rapidly and the current

mode is canceled. If this occurs, repeat this step.

3 Press a key whose function you want to store as the first

function of the new macro.

* If a key whose function cannot be stored as a command of

macro is pressed, the TRANSMIT/LEARN indicator flashes

rapidly and the current mode is canceled. If this occurs,

repeat this step.

* If about 30 seconds pass before a key is pressed, the

TRANSMIT/LEARN indicator flashes rapidly and the mode

before you began learning operations is restored. If this

occurs, restart from step 1.

4 Repeat step 3 to store the second, the third and more

functions. You can store up to seven key functions in

series as a macro.

* If the seventh key function has been learned, the

TRANSMIT/LEARN indicator flashes rapidly and the mode

before you began learning operations is restored. (This

shows that the key has completed learning a series of

functions as a macro.) If this occurs, you do no have to

follow the next step.

5 When you finish learning, press the MACRO button.

MAKING A NEW MACRO

A new macro can be programmed onto any preset macro key in place of preset functions. (See page 41 to know what keys are

preset macro keys.) You can make as many as 13 new macro keys. A macro key can learn as many as seven functions of other

keys.

Note

If you store a continuous command such as lowering of volume level, it will become a short command when it is carried out as a part

of macro.

LEARNCLEAR MACRO

It is recommended to write down new key functions you

stored on the provided user function stickers and paste

them on the reverse side of the remote control transmitter

or the reverse side of the remote control transmitter’s lid.

Memory back-up

All of the learned functions will be retained while you

replace the batteries. However, if no batteries are

installed for a few hours, the learned functions will be

erased and will have to be learned again.

Goes off.

(When learning is finished,

this indicator lights up again.)

TRANSMIT

/LEARN

LEARNCLEAR MACRO

Flashes slowly.

TRANSMIT

/LEARN

Lights up.

SYSTEM

POWER

TRANSMIT

/LEARN

REMOTE CONTROL

TRANSMITTER

English

1 To clear a learned key function, press the LEARN button

using the point of a mechanical pencil, etc.

To clear a macro you made, press the MACRO button.

2 Press and hold the CLEAR button using the point of a

mechanical pencil, etc.

3 Holding the CLEAR button pressed, press and hold the

key whose function you want to clear until the indicator

flashes 3 times.

To clear two or more functions sequentially, do not

release the CLEAR button pressed, and repeat this step.

Note

If you clear a learned function of a key, the originally preset

function of the key is restored (except the keys which are

originally preset with no function.)

To Clear a Learned Function To Clear All Learned Functions

1 Select the kind of key functions all of which you want to

clear by using the MACRO switch on the side panel of

the remote control transmitter.

OFF: Select this position if you want to clear all of the

learned functions except macros.

QUICK: Select this position if you want to clear all of the

macros you made only.

SLOW: Select this position if you want to clear all of the

learned functions including macros.

2 Press the CLEAR button using the point of a

mechanical pencil, etc.

* If one of the following operation is made after you press

the CLEAR button, the TRANSMIT/LEARN indicator

flashes rapidly and the current mode is canceled. If this

occurs, press the CLEAR button again.

• MACRO switch is switched to another position.

• Another key is pressed.

• There is no operation for about 30 seconds.

3 Press and hold the CLEAR button again. While holding

the CLEAR button pressed, press and hold the

MASTER VOLUME and keys simultaneously

until the indicator flashes 7 times.

SYMPTOM

The remote control transmitter does not

work.

Learning cannot be made successfully.

(The TRANSMIT/LEARN indicator does not

light up or flash.)

CAUSE

The batteries of this remote control

transmitter are weak.

The internal microcomputer “freezes”.

The batteries of this remote control

transmitter and/or the other remote control

transmitter are weak.

The distance between the two remote control

transmitters is too long or too short.

The signal coding or modulation of the other

remote control transmitter is not compatible

with this remote control transmitter.

Memory capacity is full.

The internal microcomputer “freezes”.

REMEDY

Replace the batteries with new ones and

press the RESET button on the remote

control transmitter.

Replace the batteries (and press the RESET

button for this remote control transmitter).

Place the remote control transmitters with the

proper distance.

Learning is not possible.

Further learning is not possible without

deleting unnecessary commands.

Press the RESET button on the remote

control transmitter.

Trouble shooting guide

MACROQUICK

OFFSLOW

CLEARING LEARNED FUNCTIONS

TRANSMIT

/LEARN

LEARNCLEAR MACRO

Flashes slowly.

TRANSMIT

/LEARN

Flashes.

LEARNCLEAR MACRO

TRANSMIT

/LEARN

Flashes slowly.

TRANSMIT

/LEARN

Flashes.

AmplifierFM

AMOthers

Remote control

transmitter

TROUBLESHOOTING

If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple

measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and

contact your authorized YAMAHA dealer or service center for help.

SYMPTOM

The unit fails to turn on when the POWER

switch is pressed, or turns off suddenly soon

after the power is turned on.

No sound or no picture.

The sound suddenly goes off.

Only one side speaker outputs the sound.

Sound “hums”.

The volume level is low while playing a record.

The volume level cannot be increased, or

sound is distorted.

No sound from the rear speakers.

No sound from the center speaker.

FM stereo reception is noisy.

There is distortion and clear reception cannot

be obtained even with a good FM antenna.

A desired station cannot be tuned in with the

automatic tuning method.

Previously preset stations can no longer be

tuned in.

A desired station cannot be tuned in with the

automatic tuning method.

There are continuous crackling and hissing

noises.

There are buzzing and whining noises

(especially in the evening).

The remote control transmitter does not work.

The sound is degraded when listening with the

headphones connected to the compact disc

player or cassette deck that are connected with

this unit.

CAUSE

Power cord is not plugged in or is not completely

inserted.

The IMPEDANCE SELECTOR switch on the rear

panel is not set to the upper or the lower end

exactly.

Incorrect output cord connections.

Appropriate input source is not selected.

The SPEAKERS switches are not set properly.

Speaker connections are not secure.

The protection circuit has been activated because

of short circuit etc.

The SLEEP timer has functioned.

Incorrect setting of the BALANCE control.

Incorrect cord connections.

No connection from the turntable to the GND

terminal.

The record is being played on a turntable with an

MC cartridge.

The power to the component connected to the REC

OUT terminals of this unit is off.

The sound output level to the rear speakers is set

to 0.

The monaural sound source is played in DOLBY

PRO LOGIC or DOLBY PRO LOGIC ENHANCED

mode.

The sound output level to the center speaker is set

to 0.

The center channel mode is in PHANTOM mode.

Incorrect sound field program selection.

Because of the characteristics of FM stereo

broadcasts, this is limited to cases where the

transmitter is too far away or the antenna input is

poor.

There is multipath interference.

The station is too weak.

This unit has been unplugged for a long period.

Weak signal or loose antenna connections.

Noises will result from ligtning, fluorescent lamps,

motors, thermostats and other electrical equipment.

A television set is being used nearby.

Direct sunlight or lighting (of an inverter type of

fluorescent lamp etc.) is striking the remote control

sensor of the main unit.

The batteries of this remote control transmitter are

too weak.

The power to this unit is off.

REMEDY

Firmly plug in the power cord.

Set the switch to the upper or the lower end exactly.

Connect the cords properly. If the problem persists,

the cords may be defective.

Select an appropriate input source with the input

selector buttons.

Set the SPEAKERS switch which corresponds to

the speakers to be used to the ON position.

Secure the connections.

Turning the unit off and then on will reset the

protection circuit.

Cancel the SLEEP timer function.

Adjust it to the appropriate position.

Connect the cords properly. If the problem persists,

the cords may be defective.

Firmly connect the audio plugs. If the problem

persists, the cords may be defective.

Make the GND connection between the turntable

and this unit.

The player should be connected to the unit through

the MC head amplifier.

Turn the power to the component on.

Raise the sound output level to the rear speakers.

Select another program suitable for the monaural

sound source.

Raise the sound output level to the center speaker.

Select NORMAL or WIDE.

Select the appropriate program.

Check the antenna connections.

Try using a high quality directional FM antenna.

Set the TUNING MODE button to the manual tuning

mode.

Adjust antenna placement to eliminate multipath

interference.

Use the manual tuning method.

Use a high quality directional FM antenna.

Repeat the presetting procedure.

Tighten the AM loop antenna connections and

rotate it for best reception.

Use the manual tuning method.

Use an outdoor antenna and a ground wire. This

will help somewhat but it is difficult to eliminate all

noise.

Relocate this unit away from the TV.

Change the position of the main unit.

Replace the batteries with new ones.

Turn the power to this unit on.

English

SPECIFICATIONS

AUDIO SECTION

Minimum RMS Output Power per Channel

Main L, R

8 ohms, 20 Hz to 20 kHz, 0.04% THD

<RX-V692>

[U.S.A. and Canada models]

..............................................80W + 80W

[Australia, Singapore and

General models]....................75W + 75W

<RX-V592>

[U.S.A. and Canada models]

..............................................75W + 75W

[Australia, Singapore and

General models]....................70W + 70W

Center

8 ohms, 20 Hz to 20 kHz, 0.07% THD

<RX-V692>

[U.S.A. and Canada models]............80W

[Australia, Singapore and

General models] ...............................75W

<RX-V592>

[U.S.A. and Canada models]............75W

[Australia, Singapore and

General models] ...............................70W

Rear

8 ohms, 1 kHz, 0.3% THD

<RX-V692>............................40W + 40W

<RX-V592>............................35W + 35W

Maximum Power [General model only]

Main L, R (8 ohms, 1 kHz, 10% THD)

<RX-V692>..........................120W+120W

<RX-V592>..........................110W+110W

Dynamic Power per Channel

(by IHF Dynamic Headroom measuring

method)

<RX-V692>

[U.S.A. and Canada models]

8/6/4/2 ohms..............115/145/175/200W

[Australia, Singapore and General models]

8/6/4/2 ohms..............100/125/150/175W

<RX-V592>

[U.S.A. and Canada models]

8/6/4/2 ohms..............110/140/170/190W

[Australia, Singapore and General models]

8/6/4/2 ohms................95/120/150/170W

Dynamic Headroom (8 ohms)

[U.S.A. and Canada models only]

<RX-V692>...................................1.58 dB

<RX-V592>...................................1.66 dB

Power Band Width

<RX-V692>

8 ohms, 40W, 0.09% THD

..........................................10 Hz to 50 kHz

<RX-V592>

8 ohms, 30W, 0.09% THD

..........................................10 Hz to 50 kHz

Damping Factor (SPEAKERS A)

8 ohms, 20 Hz to 20 kHz .............80 or more

Input Sensitivity/Impedance

PHONO MM.....................2.5 mV/47 k-ohms

CD/TAPE/DVD·LD/TV·DBS/VCR

........................................150 mV/47 k-ohms

6CH DISCRETE INPUT DVD/LD TV/DBS

<RX-V692>.................150 mV/40 k-ohms

<RX-V592>.................150 mV/50 k-ohms

Maximum Input Signal

PHONO MM

1 kHz, 0.04% THD..........................110 mV

CD/TAPE/DVD·LD/TV·DBS//VCR

(EFFECT ON)

1 kHz, 0.5% THD.................................2.2V

Output Level/Impedance

REC OUT.......................150 mV/2.5 k-ohms

PRE OUT (MAIN L/R).........2.2V/1.2 k-ohms

PRE OUT (REAR L/R)........1.6V/1.2 k-ohms

SUBWOOFER (EFFECT OFF)

............................................6.0V/1.5 k-ohms

Headphone Jack Rated Output/Impedance

Output Level (8 ohms, 0.04% THD).......0.5V

Impedance.....................................390 ohms

Frequency Response (20 Hz to 20 kHz)

CD/TAPE/DVD·LD/TV·DBS//VCR

........................................................0±0.5 dB

RIAA Equalization Deviation

PHONO MM....................................0±0.5 dB

Total Harmonic Distortion (20 Hz to 20 kHz)

PHONO MM to REC OUT

1V.....................................................0.02%

CD/TAPE/DVD·LD/TV·DBS/VCR

to SP OUT

<RX-V692>

40W/8 ohms.................................0.025%

<RX-V592>

30W/8 ohms.................................0.025%

Signal-to-Noise Ratio (IHF-A Network)

PHONO MM to REC OUT

(5 mV Input Shorted)

<RX-V692>

[U.S.A., Canada and General models]

........................................................86 dB

[Australia and Singapore models]

........................................................83 dB

<RX-V592>

[U.S.A., Canada and General models]

........................................................85 dB

[Australia and Singapore models]

........................................................82 dB

CD/TAPE/DVD·LD/TV·DBS/VCR

to SP OUT

(Shorted)..............................................98 dB

Residual Noise (IHF-A Network)

MAIN L/R...........................................140 µV

Channel Separation

(Vol. –30 dB, EFFECT OFF)

PHONO MM

(Input Shorted, 1 kHz/10 kHz)

................................................60 dB/50 dB

CD/TAPE/DVD·LD/TV·DBS/VCR

(Input 5.1 k-ohms Terminated,

1 kHz/10 kHz) .........................60 dB/45 dB

Tone Control Characteristics

BASS: Boost/cut................±10 dB (50 Hz)

Turnover Frequency.........(350 Hz)

TREBLE: Boost/cut...........±10 dB (20 kHz)

Turnover Frequency.....(3.5 kHz)

Bass Extension..........................+6 dB (50 Hz)

Gain Tracking Error (0 to –60 dB)............3 dB

VIDEO SECTION

Video Signal Type

[U.S.A. and Canada models]...............NTSC

[Australia and Singapore models] ..........PAL

[General model]...........................NTSC/PAL

Video Signal Level..................1 Vp-p/75 ohms

S-Video Signal Level

Y ..........................................1 Vp-p/75 ohms

C ...................................0.286 Vp-p/75 ohms

Maximum Input Level............1.5 Vp-p or more

<RX-V692 only>

S-Video C ........................0.5 Vp-p or more

Signal-to-Noise Ratio................50 dB or more

Monitor Out Frequency Response

..................................5 Hz to 10 MHz, –3 dB

FM SECTION

Tuning Range

[U.S.A. and Canada models]

..........................................87.5 to 107.9 MHz

[Australia, Singapore and

General models]................87.5 to 108.0 MHz

50 dB Quieting Sensitivity (IHF, 75 ohms)

[U.S.A., Canada and General models only]

Mono...............................1.55 µV (15.1 dBf)

Stereo................................21 µV (37.7 dBf)

Usable Sensitivity

DIN, Mono (S/N 26 dB)

[Australia and Singapore models]

...........................................................0.9 µV

DIN, Stereo (S/N 46 dB)

[Australia and Singapore models]

............................................................24 µV

Image Response Ratio

[U.S.A., Canada and General models]

..............................................................45 dB

[Australia and Singapore models]

..............................................................80 dB

IF Response Ratio

[U.S.A., Canada and General models]

.............................................................70 dB

[Australia and Singapore models]........80 dB

Spurious Response Ratio........................70 dB

AM Suppression Ratio.............................55 dB

Capture Ratio..........................................1.5 dB

Alternate Channel Selectivity

[U.S.A., Canada and General models]

..............................................................85 dB

Selectivity (two signals, 40 kHz Dev.

300 kHz)

[Australia and Singapore models]

........70 dB

Signal-to-Noise Ratio

(IHF) Mono/Stereo

[U.S.A., Canada and General models]

.................................................80 dB/75 dB

(DIN-Weighted, 40 kHz Dev.) Mono/Stereo

[Australia and Singapore models]

.................................................75 dB/70 dB

Harmonic Distortion

Mono/Stereo (1 kHz) ........................0.1/0.2%

Stereo Separation (1 kHz)......................50 dB

Frequency Response

20 Hz to 15 kHz.............................0 ±1.5 dB

AM SECTION

Tuning Range

[U.S.A., Canada and General models]

.............................................530 to 1,710 kHz

[Australia and Singapore models]

.............................................531 to 1,611 kHz

Usable Sensitivity.............................100 µV/m

Selectivity...............................................32 dB

Signal-to-Noise Ratio .............................50 dB

Image Response Ratio...........................40 dB

Spurious Response Ratio.......................50 dB

Harmonic Distortion (1 kHz) ....................0.3%

AUDIO SECTION

Output Level/Impedance

FM (100% mod., 1 kHz)

[U.S.A., Canada and General models]

......................................500 mV/2.2 k-ohms

[Australia and Singapore models]

......................................400 mV/2.2 k-ohms

AM (30% mod., 1 kHz)

.........................................150 mV/2.2 k-ohms

GENERAL

Power Supply

[U.S.A. and Canada models]

..............................................AC 120V, 60 Hz

[Australia model]...................AC 240V, 50 Hz

[Singapore model].................AC 230V, 50 Hz

[General model]

....................AC 110/120/220/240V, 50/60 Hz

Power Consumption

<RX-V692>

[U.S.A. model]...................................240W

[Canada model].................................280W

[Australia, Singapore and

General models]................................290W

<RX-V592>

[U.S.A. model]...................................230W

[Canada model].................................250W

[Australia, Singapore and

General models]................................270W

Maximum Power Consumption

(8 ohms, 1 kHz, 10% THD, When 5 channels

are driven:)

[General model only]

<RX-V692>...................................690W

<RX-V592>...................................630W

AC Outlets

2 SWITCHED OUTLETS

[U.S.A., Canada, Singapore and General

models].............................100W max. total

1 SWITCHED OUTLET

[Australia model]...............100W max. total

Dimensions (W x H x D)

.....................................435 x 151 x 379.5 mm

(17-1/8” x 5-15/16” x 14-15/16”)

Weight

<RX-V692>...............12.5 kg (27 lbs. 8 oz.)

<RX-V592>...............11.0 kg (24 lbs. 3 oz.)

Accessories..........................AM loop antenna

Indoor FM antenna

Remote control transmitter

Batteries

User function stickers

Antenna adapter

(U.S.A. and Canada models only)

Specifications are subject to change without

notice.

Relación de supresión de AM ...............55 dB

Relación de captura .............................1,5 dB

Selectividad de canal alternativo

[Modelos para EE.UU., Canadá y General]

............................................................85 dB

Selectividad (dos señales, desviación de

40 kHz ±300 kHz)

[

Modelos para Australia y Singapur

]

.............................................................70 dB

Relación señal-ruido

(IHF) Monaural/Estéreo

[Modelos para EE.UU., Canadá y General]

.....................................................80/75 dB

(DIN, ponderación, desviación de 40 kHz)

Monaural/Estéreo

[

Modelos para Australia y Singapur]

.....................................................75/70 dB

Distorsión armónica

Monaural/Estéreo (1 kHz)...............0,1/0,2%

Separación entre canales estéreo (1 kHz)

...............................................................50 dB

Respuesta en frecuencia

20 Hz a 15 kHz .............................0 ±1,5 dB

SECCION DE AM

Gama de sintonía

[Modelos para EE.UU. y General]

........................................... 530 a 1.710 kHz

[

Modelos para Australia y Singapur

]

............................................531 a 1.611 kHz

Sensibilidad útil ...............................100 µV/m

Selectividad ...........................................32 dB

Relación señal-ruido ..............................50 dB

Relación de respuesta de frecuencia imagen

...............................................................40 dB

Relación de respuesta espuria.............. 50 dB

Distorsión armónica (1 kHz) ...................0,3%

SECCION DE AUDIO

Nivel/impedancia de salida

FM (modulación al 100%, 1 kHz)

[Modelos para EE.UU., Canadá y General]

..................................500 mV/2,2 k-ohmios

[

Modelos para Australia y Singapur

]

..................................400 mV/2,2 k-ohmios

AM (modulación al 30%, 1 kHz)

....................................150 mV/2,2 k-ohmios

GENERAL

Alimentación

[Modelos para EE.UU. y Canadá]

............................................120V CA, 60 Hz

[Modelo para Australia] .......240V CA, 50 Hz

[Modelo para Singapur] ......230V CA, 50 Hz

[Modelo General]

..................110/120/220/240V CA, 50/60 Hz

Consumo

RX-V692

[Modelo para EE.UU.].........................240W

[Modelo para Canadá] ........................280W

[Modelos para Australia, Singapur y

General] ..............................................290W

RX-V592

[Modelo para EE.UU.].........................230W

[Modelo para Canadá] ........................250W

[Modelos para Australia, Singapur y

General] ..............................................270W

Consumo máximo de corriente

(8 ohmios, 1 kHz, 10% D.A.T. cuando se

usan los 5 canales:)

[Modelo General]

RX-V692

.....................................690W

RX-V592

.....................................630W

Tomacorrientes de CA

2 tomacorrientes con interruptor

[Modelos para EE.UU., Canadá,

Singapur y General] ..................100W max.

1 tomacorriente con interruptor

[Modelo para Australia].............100W max.

Dimensiones (An x Al x Prf)

.....................................435 x 151 x 379,5 mm

Peso

RX-V692

........................................12,5 kg

RX-V592

........................................11,0 kg

Accesorios ..........................Antena de cuadro

Antena FM interior

Transmisor de control remoto

Pilas

Etiqueta de funciones del usuario

Adaptador de antena (Sólo modelos para

EE.UU. y Canadá)

Especificaciones sujetas a cambios sin previo

aviso.

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

VV56430 Printed in Malaysia

Yamaha RX-V692 El manual del propietario

Marca: Yamaha

Modelo: RX-V692

Categoría: Reproductores de casete

Tipo: El manual del propietario

Descargar PDF

informe

En otros idiomas

français: Yamaha RX-V692 Le manuel du propriétaire
italiano: Yamaha RX-V692 Manuale del proprietario
English: Yamaha RX-V692 Owner's manual
Deutsch: Yamaha RX-V692 Bedienungsanleitung
русский: Yamaha RX-V692 Инструкция по применению
Nederlands: Yamaha RX-V692 de handleiding
português: Yamaha RX-V692 Manual do proprietário
dansk: Yamaha RX-V692 Brugervejledning
polski: Yamaha RX-V692 Instrukcja obsługi
čeština: Yamaha RX-V692 Návod k obsluze
svenska: Yamaha RX-V692 Bruksanvisning
Türkçe: Yamaha RX-V692 El kitabı
suomi: Yamaha RX-V692 Omistajan opas
română: Yamaha RX-V692 Manualul proprietarului

Yamaha RX-V692 El manual del propietario

Yamaha RX-V692 El manual del propietario

En otros idiomas

Documentos relacionados