Transcripción de documentos

POWERED POWERED MIXER MIXER Owner’s Manual Quick Guide Pages 6 to 12 Making the Most of Your Mixer Pages 13 to 19 EN  Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUT I ON RISK OF ELECTRIC SHOCK DO NOT OPEN The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the rear of the unit. IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 8 9 10 Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 12 13 14 Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. (98-6500) IMPORTANT Please record the serial number of this unit in the space below. Model: Serial No.: The serial number is located on the bottom or rear of the unit. Retain this Owner’s Manual in a safe place for future reference. 2 EMX512SC/EMX312SC/EMX212S  PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply/Power cord Water warning • Only use the voltage specified as correct for the device. The required voltage is printed on the name plate of the device. • Use only the included power cord. • Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it. • Be sure to connect to an appropriate outlet with a protective grounding connection. Improper grounding can result in electrical shock. Do not open • Do not open the device or attempt to disassemble the internal parts or modify them in any way. The device contains no user-serviceable parts. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel. • Do not expose the device to rain, use it near water or in damp or wet conditions, or place containers on it containing liquids which might spill into any openings. • Never insert or remove an electric plug with wet hands. If you notice any abnormality • If the power cord or plug becomes frayed or damaged, or if there is a sudden loss of sound during use of the device, or if any unusual smells or smoke should appear to be caused by it, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel. • If this device should be dropped or damaged, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel. CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: Power supply/Power cord • Remove the electric plug from the outlet when the device is not to be used for extended periods of time, or during electrical storms. • When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it. Location • Before moving the device, remove all connected cables. • When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. • If this device is to be mounted in an EIA-standard rack, leave the back of the rack open and make sure that it is at least 10 cm away from walls or surfaces. Also, if this device is to be mounted with devices that tend to generate heat, such as power amplifiers, be sure to keep an adequate gap between this device and the heat-generating devices or install ventilation panels to prevent high temperatures from developing inside this device. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire. • Do not use the device in a confined, poorly-ventilated location. If this device is to be used in a small space other than an EIA-standard rack, make sure that there is adequate space between the device and surrounding walls or other devices: at least 10 cm at the sides, 25 cm behind and 15 cm above. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fi re. • Avoid setting all equalizer controls and faders to their maximum. Depending on the condition of the connected devices, doing so may cause feedback and may damage the speakers. • Do not expose the device to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components. (5)-4 • Do not place the device in an unstable position where it might accidentally fall over. • Do not block the vents. This device has ventilation holes at the rear and side to prevent the internal temperature from becoming too high. In particular, do not place the device on its side or upside down. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire. • Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Doing so may result in noise, both in the device itself and in the TV or radio next to it. Connections • Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. • Use only speaker cables for connecting speakers to the speaker jacks. Use of other types of cables may result in fire. • Do not use speaker cables with a metal-housing connector. Doing so may result in electrical shock due to differences in voltage. Use speaker cables with a nonmetal-housing connector, or with a insulated-housing connector. Handling caution • When turning on the AC power in your audio system, always turn on the device or external power amplifiers LAST, to avoid speaker damage. When turning the power off, the device or external power amplifiers should be turned off FIRST for the same reason. • Do not insert your fingers or hands in any gaps or openings on the device (vents, etc.). • Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any gaps or openings on the device (vents, etc.) If this happens, turn off the power immediately and unplug the power cord from the AC outlet. Then have the device inspected by qualified Yamaha service personnel. • Do not use the device for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. • Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on the buttons, switches or connectors. 2/3 EMX512SC/EMX312SC/EMX212S 3  XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-). Use only Neutrik plugs (NL4) for connecting Speakon connectors. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device. Always turn the power off when the device is not in use. The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualifi ed Yamaha service personnel about replacing defective components. IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT. The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured GREEN or GREEN-and-YELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. • This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd. (3 wires) FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B) About this Manual This manual is divided into two main sections, as follows. ■ Mixer Basics (starts on page 6) Presents a general explanation of mixers and mixer concepts. Includes a Quick Guide that will help beginners get up to speed very quickly. ■ EMX Setup and Operation (starts on page 20) Provides detailed information about the EMX. Introduces the EMX features, identifies and explains the controls, indicators, and connectors; and explains how to set up the equipment. * This manual applies to models EMX512SC, EMX312SC, and EMX212SC. Within this manual, the term “EMX” is used to refer to all three of these models. * Illustrations herein are for explanatory purposes only, and may not match actual appearance during operation. * Company names and product names herein are trademarks or registered trademarks of their respective companies. Copying of commercially available music or other audio data for purposes other than personal use is strictly prohibited by copyright law. Please respect all copyrights, and consult with a copyright specialist if you are in doubt about permissible use. 4 EMX512SC/EMX312SC/EMX212S  Thank you for your purchase of this Yamaha EMX512SC, EMX312SC, or EMX212S power mixer. Please read through this manual carefully before beginning use, so that you will be able to take full advantage of your mixer’s superlative features and enjoy trouble-free operation for years to come. After reading the manual, please store it in a safe place. Contents Features ■ Basic Quick Guide Input Channels..................................... page 20 6 Before Turning On the Mixer........................................ 6 Getting Sound to the Speakers .................................... 7 Adding Some Reverb ................................................. 11 Using the Compressors to Enhance Vocals .............. 12 Making the Most of Your Mixer 13 A Place for Everything and Everything in its Place .... 13 A Plethora of Connectors—What Goes Where? ... 13 Balanced, Unbalanced—What’s the Difference? .. 14 Signal Levels and the Decibel.................................... 15 Making Better Mixes................................................... 15 Approaching the Mix—Where Do You Start? ...... 15 To EQ or Not to EQ.............................................. 16 Ambience ............................................................. 17 The Modulation Effects: Phasing, Chorus, and Flanging ........................................................ 18 Compression ........................................................ 18 ■ Reference Controls and Connectors 20 Controls on Each Channel ......................................... 20 Digital Effects Section ................................................ 22 MAIN Section ............................................................. 23 MONITOR Section ..................................................... 24 POWER Section ........................................................ 25 Rear Panel ................................................................. 26 Connecting Speakers Horizontal Orientation, Tilting and Rack Mounting 27 The EMX offers four monoaural mic/line input channels (1 to 4) and four stereo input channel pairs (5/6 to 11/12), allowing you to freely mix inputs from microphones, linelevel devices, and stereo devices. For example, you can mix four microphones with four stereo devices, or seven microphones with one stereo synthesizer. Phantom Power (+15V)........................ page 25 A single switch turns phantom power on to all mic inputs. Use this feature to provide power to condenser microphones. High-Quality Digital Effects ................ page 22 The mixer’s internal effector is in the same league as our SPX effector series, allowing you to create a rich range of variations with no external help. But of course you are also free to use the EFFECT OUT jack to connect to an external effector of your choice. MAIN and MONITOR Outputs ............. page 23 The mixer offers excellent independent control of main and monitor output. The top panel offers separate main and monitor outputs, while the POWER AMP switch can be used to set the SPEAKERS jacks so that they output either the main signal to both speakers or else the main signal to one speaker and the monitor signal to the other. Separate MASTER control knobs and 7-segment graphic equalizers are also provided. Compressors (EMX512SC and EMX312SC only) .................................. page 21 Compressors on channels 1 to 4 can be used to squeeze the dynamic range of inputs such as microphones and acoustic guitars, attenuating the higher levels and bringing out the lower ones. This feature helps reduce distortion and allows overall volume to be set higher, resulting in a stronger and more impressive sound. 28 Tilt Setup or Rack Mount ................... page 29 Horizontal Orientation ................................................ 28 Tilting ......................................................................... 29 Rack Mounting ........................................................... 29 The EMX can be positioned at an angle or mounted in a rack, allowing for easy accessibility in a wide variety of setups. Setting Up Troubleshooting Specifications 30 31 32 Internal Power Amp ............................. page 25 The internal amp makes it possible to connect the SPEAKERS jacks directly to non-powered speakers, with no need for an external amplifier in between. The rear panel offers two types of speaker connectors: phone jacks and Neutrik Speakon jacks. EMX512SC/EMX312SC/EMX212S 5  BASIC Quick Guide Before Turning On the Mixer ■ Connecting to Power 1 2 3 Be sure that the POWER switch is in the OFF position. Connect the included power cord to the AC IN connector on the rear panel. Plug the power cord into a standard power outlet. ■ Turning the Unit On and Off NOTE • To prevent an unpleasant burst of noise from the speakers, you should power up the sound sources first, and then the other devices in order of their distance from the source (starting with the closest). For example: Sound source (external device) → EMX unit When turning power off, proceed in the opposite order. → Amps (Powered speakers) • Before turning power on, make sure that the LEVEL and MASTER knobs are set to the “0” position. 1 Push the POWER switch in to turn the power ON. The power lamp lights up to indicate that power is on. To turn the power off, push the switch again, so that it pops out. Rapidly turning the unit ON and OFF in succession can cause it to malfunction. After turning the unit OFF, wait for about 10 seconds before turning it ON again. 6 EMX512SC/EMX312SC/EMX212S  BASIC Quick Guide Getting Sound to the Speakers We begin by connecting up two speakers and generating some stereo output. Note that operations and procedures will vary somewhat according to the input devices you are using. 5 3 2,7,9 6 2,8 4 1 1 1 Connect up the speakers and your input devices (microphones, instruments, etc.) Use non-powered speakers and dedicated speaker cable. Connect one speaker to SPEAKERS jack A (A1 or A2), and the other to jack B (B1 or B2). Then connect your input devices (microphones, guitar, etc.) to the appropriate input jacks on the top panel. For details, see page 30. RIGHT WRONG!! Before connecting input devices to the EMX, be sure that all of these devices (including microphones) are powered off. And before turning the power to any device on or off, be sure to turn the volume of that device all the way down. Neglect of these precautions may result in large noise bursts that may damage your equipment, your ears, or both. NOTE We recommend that you do not connect electric instruments (such as electric guitars and basses) directly to the EMX. Instead, these instruments should be connected through an intermediary device such as a direct box, a preamp (guitar amp), or an amp simulator. Never connect both A and B jacks to a single speaker. Connection of both jacks to the same speaker may result in damage to the mixer. EMX512SC/EMX312SC/EMX212S 7  BASIC Quick Guide 2 Turn the LEVEL knobs and the MASTER knobs to 0. This position This position 3 Set the POWER AMP switch to its upper position (to MAIN L-R). For information about this switch, see page 25. 8 EMX512SC/EMX312SC/EMX212S  BASIC Quick Guide 4 If you have connected input devices to channels 1 to 4, set the LINE/MIC switch on each channel accordingly. If you have connected a line-level device, such as a keyboard or audio device, set the channel’s switch to the LINE position ( ). If you have connected a microphone or other mic-level device, set the switch to the MIC position ( ). 5 If you are using one or more condenser microphones for your inputs, set the PHANTOM switch to the ON position ( ). • Be sure to leave this switch off if you do not need phantom power. 6 Turn on the power. First turn on the power to all connected devices other than powered speakers and amp, and then turn on the EMX itself. If using powered speakers or amps, turn these on last. • When using phantom power, do not connect any devices other than condenser microphones to the XLR input jacks. Other devices may be damaged if connected to phantom power. This precaution does not apply to balanced dynamic microphones, however, as these will not be affected by phantom power. • Before turning the PHANTOM switch ON or OFF, be sure to turn off the power to the mixer and to all other devices having internal amplifiers. It is also recommended that you set both MASTER knobs to their “0” position. Neglect of these precautions may result in damage to speakers, to other equipment, or to your ears. EMX512SC/EMX312SC/EMX212S 9  BASIC Quick Guide 7 Turn the MASTER knob in the MAIN section to the posi- tion. This position 8 9 Adjust the LEVEL knobs for all occupied channels. For each input device you have connected: Generate sound from the device while adjusting the corresponding channel’s LEVEL knob. Adjust so that the LEVEL meter occasionally reaches the “0” level. Now turn the MASTER knob in the MAIN section again as necessary to adjust the overall output level. It is acceptable for the LIMITER lamps to flash on briefly at times, but if they remain lit continuously then there is risk of damage to your speakers or to the internal amp. Reduce the MASTER knob setting so that these lamps do not stay on. 10 EMX512SC/EMX312SC/EMX212S  BASIC Quick Guide Adding Some Reverb Now let’s try adding some reverb to your input. The reverb effects let you simulate the sound of different performance environments—such as concert halls and small clubs. 2 3 1 2 3 4 1 Turn the ON switch to it’s ON position. This switch turns the internal effector on and off. The lamp lights up orange to indicate that the effector is on. As an alternative to the ON switch, you can use a separately sold FC5 foot switch to toggle the effector on and off. Turn the PROGRAM dial to select the desired effect type; To select a reverb effect, turn the dial to any value from 1 to 7. 1 2 3 4 5 6 7 8 REVERB HALL 1 REVERB HALL 2 REVERB ROOM 1 REVERB ROOM 2 REVERB STAGE 1 REVERB STAGE 2 REVERB PLATE DRUM AMBIENCE 9 0 A B C D E F KARAOKE ECHO VOCAL ECHO CHORUS 1 CHORUS 2 FLANGER PHASER AUTO WAH DISTORTION Use the channel EFFECT knobs to adjust the effect depth for each channel. EMX512SC/EMX312SC/EMX212S 11  BASIC Quick Guide 4 Use the MAIN section’s EFFECT RTN knob to adjust the overall effect depth. Note that you can use the PARAMETER knob to adjust the characteristic sound of the selected effect. If you have selected a reverb effect, the knob will adjust the reverb time. Using the Compressors to Enhance Vocals (EMX512SC and EMX312SC only) The compressor evens out the input level, reducing the level of loud passages and bringing up softer passages. The result is a cleaner sound where nuances remain audible and the lyrics are easier to hear. 1 1 12 Adjust the COMP knobs on the relevant channels. Turn the knob clockwise to increase the compression. Avoid setting the value too high, as too much compression may lead to howling. For more information about the compressors, see pages 18 and 21. EMX512SC/EMX312SC/EMX212S  BASIC Making the Most of Your Mixer An Introduction You’ve got yourself a mixer and now you’re ready to use it. Just plug everything in, twiddle the controls, and away you go … right? Well, if you’ve done this before you won’t have any problems, but if this is the first time you’ve ever used a mixer you might want to read through this little tutorial and pick up a few basics that will help you get better performance and make better mixes. A Place for Everything and Everything in its Place A Plethora of Connectors—What Goes Where? Questions you’re likely to encounter when setting up a system for the first time might include “Why all these different types of connectors on the back of my mixer?” and “What’s the difference?”. Let’s start by taking a look at the most common connector types. This is the “consumer connector,” and the one that has been most commonly used on home audio gear for many years. Also known as “phono” jacks (short for “phonogram”), but the term isn’t used much these days—besides, it’s too easily confusable with “phone” jacks, below. RCA pin jacks are always unbalanced, and generally carry a line-level signal at –10 dB, nominal. You’re most likely to use this type of connector when connecting a CD player or other home audio type source to your mixer, or when connecting the output of your mixer to a cassette recorder or similar gear. designed to handle just by looking at them. It could be unbalanced mono, unbalanced stereo, balanced mono, or an insert patch point. The connector’s label will usually tell you what type of signal it handles, as will the owner’s manual (you do keep your manuals in a safe place, don’t you?). A phone jack that is set up to handle balanced signals is also often referred to as a “TRS” phone jack. “TRS” stands for TipRing-Sleeve, which describes the configuration of the phone plug used. The Sturdy XLR The Versatile Phone Jack Male Stereo/TRS phone plug The Venerable RCA Pin Jack Female White Red Mono phone plug The name “phone jack” arose simply because this configuration was first used in telephone switchboards. Phone jacks can be tricky because you can’t always tell what type of signal they’re This type of connector is generally referred to as “XLRtype,” and almost always carries a balanced signal. If the corresponding circuitry is designed properly, however, XLR- EMX512SC/EMX312SC/EMX212S 13  BASIC Making the Most of Your Mixer type connectors will also handle unbalanced signals with no problem. Microphone cables usually have this type of connector, as do the inputs and outputs of most professional audio gear. Balanced noise cancellation Noise Hot (+) In a word: “noise.” The whole point of balanced lines is noise rejection, and it’s something they’re very good at. Any length of wire will act as an antenna to pick up the random electromagnetic radiation we’re constantly surrounded by: radio and TV signals as well as spurious electromagnetic noise generated by power lines, motors, electric appliances, computer monitors, and a variety of other sources. The longer the wire, the more noise it is likely to pick up. That’s why balanced lines are the best choice for long cable runs. If your “studio” is basically confined to your desktop and all connections are no more than a meter or two in length, then unbalanced lines are fine—unless you’re surrounded by extremely high levels of electromagnetic noise. Another place balanced lines are almost always used is in microphone cables. The reason for this is that the output signal from most microphones is very small, so even a tiny amount of noise will be relatively large, and will be amplified to an alarming Noise-free signal Cold (–) Balanced, Unbalanced—What’s the Difference? Phase inversion Noise cancelled Ground Source Cable degree in the mixer’s high-gain head amplifier. How Do Balanced Lines Reject Noise? ** Skip this section if technical details make you queasy. ** Balanced lines work on the principle of “phase cancellation”: if you add two identical signals out of phase (i.e. one signal is inverted so its peaks coincide with the troughs in the other signal), the result is … nothing. A flat line. The signals cancel each other out. A balanced cable has three conductors: 1) A ground conductor which carries no signal, just the “ground” or “0” reference against which the signal in the other conductors fluctuates. To summarize 14 Microphones: Use balanced lines. Short line-level runs: Unbalanced lines are fine if you’re in a relatively noise-free environment. Long line-level runs: The ambient electromagnetic noise level will be the ultimate deciding factor, but balanced is best. EMX512SC/EMX312SC/EMX212S Receiving device 2) A “hot” or “+” conductor which carries the normal-phase audio signal. 3) A “cold” or “–” conductor which carries the reverse-phase audio signal. Balanced Unbalanced Hot Cold Shield (Ground) Outer Insulation While the desired audio signals in the hot and cold conductors are out of phase, any noise induced in the line will be exactly the same in both conductors, and thus in phase. The trick is that the phase of one signal is reversed at the receiving end of the line so that the desired audio signals become in-phase, and the induced noise suddenly finds itself out of phase. The out-of-phase noise signal is effectively canceled while the audio signal is left intact. Clever, eh?  BASIC Making the Most of Your Mixer way, but a more systematic approach that is suited to the material you’re mixing will produce much better results, and faster. There are no rules, and you’ll probably end up developing a system that works best for you. But the key is to develop a system rather than working haphazardly. Here are a few ideas to get you started: Unbalanced noise Noise Source Cable Receiving device Faders Down Signal Levels and the Decibel Let’s take a look at one of the most commonly used units in audio: the decibel (dB). If the smallest sound that can be heard by the human ear is given an arbitrary value of 1, then the loudest sound that can be heard is approximately 1,000,000 (one million) times louder. That’s too many digits to deal with for practical calculations, and so the more appropriate “decibel” (dB) unit was created for sound-related measurements. In this system the difference between the softest and loudest sounds that can be heard is 120 dB. This is a nonlinear scale, and a difference of 3 dB actually results in a doubling or halving of the loudness. You might encounter a number of different varieties of the dB: dBu, dBV, dBM and others, but the dBu is the basic decibel unit. In the case of dBu, “0 dBu” is specified as a signal level of 0.775 volts. For example, if a microphone’s output level is –40 dBu (0.00775 V), then to raise that level to 0 dBu (0.775 V) in the mixer’s preamp stage requires that the signal be amplified by 100 times. A mixer may be required to handle signals at a wide range of levels, and it is necessary match input and output levels as closely as possible. In most cases the “nominal” level for a mixer’s input and outputs is marked on the panel or listed in the owner’s manual. It might sound overly simple, but it is usually a good idea to start with all channel faders off—all the way down. It’s also possible to start with all faders at their nominal settings, but it’s too easy to lose perspective with this approach. Start with all faders down, then bring them up one by one to fill out the mix. But which channel should you start with? Making Better Mixes Example1: Vocal Ballad Backed by Piano Trio Approaching the Mix—Where Do You Start? What are you mixing? Is it a song in which the vocals are the most important element? Mixing is easy, right? Just move the faders around until it sounds right? Well, you can do it that + 20 dBu 0 dBu Most professional mixers, power amplifiers, and other types of equipment have inputs and outputs with a nominal level of +4 dBu. 0.775 V The inputs and outputs on home-use audio gear usually have a nominal level of –10 dBu. -20 dBu -40 dBu -60 dBu Microphone signal levels vary over a wide range depending on the type of microphone and the source. Average speech is about –30 dBu, but the twittering of a bird might be lower than –50 dBu while a solid bass drum beat might produce a level as high as 0 dBu. EMX512SC/EMX312SC/EMX212S 15  BASIC Making the Most of Your Mixer If so you might want to build the mix around the vocals. This means bringing the vocal channel up to nominal first (if your level setup procedure has been done properly this will be a good starting point), and then adding the other instruments. What you add next will depend on the type of material you are working with and your approach to it. If the vocals are backed by a piano trio and the song is a ballad, for example, you might want to bring in the piano next and get the vocal/piano relationship just right, then bring in the bass and drums to support the overall sound. Example2: Funky R&B Groove The approach will be totally different if you’re mixing a funky R&B number that centers on the groove. In this case most engineers will start with the drums, and then add the bass. The relationship between the drums and bass is extremely important to achieve the “drive” or groove the music rides on. Pay particular attention to how the bass works with the kick (bass drum). They should almost sound like a single instrument— with the kick supplying the punch and the bass supplying the pitch. Once again, there are no rules, but these are concepts that have been proven to work well. 16 EMX512SC/EMX312SC/EMX212S The fundamental and harmonic musical instruments. frequency ranges of some Cymbal Piano Bass Drum Snare Drum Bass Guitar Trombone Trumpet 20 50 100 200 500 1k 2k 5k 10 k 20 k (Hz) Fundamental: The frequency that determines the basic musical pitch. Harmonics: Multiples of the fundamental frequency that play a role in determining the timbre of the instrument. Some Frequency Facts The lowest and highest frequencies than can be heard by the human ear are generally considered to be around 20 Hz and 20,000 Hz, respectively. Average conversation occurs in the range from about 300 Hz to about 3,000 Hz. The frequency of a standard pitchfork used to tune guitars and other instruments is 440 Hz (this corresponds to the “A3” key on a piano tuned to concert pitch). Double this frequency to 880 Hz and you have a pitch one octave higher (i.e. “A4” on the piano keyboard). In the same way you can halve the frequency to 220 Hz to produce “A2” an octave lower. The frequencies controlled by the LOW, MID, and HIGH bands on this mixer have been specifically selected to provide the most “musical” range of adjustment with the widest possible range of instruments (100Hz, 2,500 Hz, and 10,000 Hz, respectively). To EQ or Not to EQ Cut for a Cleaner Mix In general: less is better. There are many situations in which you’ll need to cut certain frequency ranges, but use boost sparingly, and with caution. Proper use of EQ can eliminate interference between instruments in a mix and give the overall sound better definition. Bad EQ—and most commonly bad boost—just sounds terrible. For example: cymbals have a lot of energy in the mid and low frequency ranges that you don’t really perceive as musical sound, but which can interfere with the clarity of other instruments in these ranges. You can basically turn the low EQ on cymbal channels all the way down without changing the way they sound in the mix. You’ll hear the difference, however, in the way the mix sounds more “spacious,” and instruments in the lower ranges will have better definition. Surprisingly enough, piano also  BASIC Making the Most of Your Mixer Boost with Caution If you’re trying to create special or unusual effects, go ahead and boost away as much as you like. But if you’re just trying to achieve a good-sounding mix, boost only in very small increments. A tiny boost in the midrange can give vocals more presence, or a touch of high boost can give certain instruments more “air.” Listen, and if things don’t sound clear and clean try using cut to remove frequencies that are cluttering up the mix rather than trying to boost the mix into clarity. One of the biggest problems with too much boost is that it adds gain to the signal, increasing noise and potentially overloading the subsequent circuitry. Ambience Your mixes can be further refined by adding ambience effects such as reverb or delay. On the EMX mixers these effects are built in. The internal DSP (Digital Signal Processor) can be used to add reverb or delay to individual channels in the same way as external effects processors, with the extra connections required by, or the loss in sound quality often MID Boost Signal Level (dB) has an incredibly powerful low end that can benefit from a bit of low-frequency roll-off to let other instruments—notably drums and bass—do their jobs more effectively. Naturally you won’t want to do this if the piano is playing solo. The reverse applies to kick drums and bass guitars: you can often roll off the high end to create more space in the mix without compromising the character of the instruments. You’ll have to use your ears, though, because each instrument is different and sometimes you’ll want the “snap” of a bass guitar, for example, to come through. MID Flat LOW Boost HIGH Boost LOW Flat HIGH Flat LOW Cut HIGH Cut MID Cut Frequency (Hz) caused by external processing. (Refer to page 22). You need to be careful not to overdo effects, however, because going to far can undermine the clarity and quality of your mix. Use your ambience effects just enough to create the required feeling of depth, but no more than is necessary to keep your sound clean. Reverb and Delay Time A variety of reverb and delay effect programs are provided, and nearly all of then have a reverb/delay time parameter than can be adjusted via the panel PARAMETER control. Small adjustments to the reverb/ delay time can actually have a significant effect on the sound. The optimum reverb time for a piece of music will depend on the music’s demo and density, but as a general rule longer reverb times are good for ballads, while shorter reverb times are more suited to up-tempo tunes. Delay times can be adjusted to create a wide variety of “grooves”, and you need to select the time that best suits the music. When adding delay to a vocal, for example, try setting the delay time to dotted eighth notes corresponding to the tune’s tempo. Reverb Tone Different reverb programs will have different “reverb tone” due to differences in the reverb time of the high or low frequencies, or differences in the overall frequency response of the reverb sound. Always be careful not apply too much reverb, particularly in the high frequencies. In addition to resulting in unnatural sound, excessive high-frequency reverb can interfere with the high frequencies in other parts of the mix. If you can hear more reverb than direct sound in the upper frequency range, try selecting a different effect program. It’s always a good idea to choose a reverb program that gives you the depth you want without detracting from the clarity of the mix. Reverb Level It’s amazing how quickly your ears can lose perspective and fool you into believing that a totally washed-out mix sounds perfectly fine. To avoid falling into this trap start with reverb level all EMX512SC/EMX312SC/EMX212S 17  BASIC Making the Most of Your Mixer the way down, then gradually bring the reverb into the mix until you can just hear the difference. Any more than this normally becomes a “special effect.” You don’t want reverb to dominate the mix unless you are trying to create the effect of a band in a cave—which is a perfectly legitimate creative goal if that’s the sort of thing you’re aiming for. The Modulation Effects: Phasing, Chorus, and Flanging All of these effects work on basically the same principle: a portion of the audio signal is “time-shifted” and then mixed back with the direct signal. The amount of time shift is controlled, or “modulated”, by an LFO (Lowfrequency Oscillator). When we say “time shift,” however, we’re not talking in terms of minutes or even seconds. For phasing effects the shift is very small indeed – a difference measured in degrees of phase shift rather than time units. The phase difference between the modulated and direct signals causes cancellation at some frequencies and reinforces the signal at others – a “comb filter” effect – and this causes the shimmering sound we hear. Phasing is the subtlest of all these effects, producing a gentle shimmer that can add life to a wide range of sources without being too obtrusive. For chorus and flanging the signal is actually delayed by several milliseconds (a millisecond is a thousandth of a second), with the delay time modulated by an LFO, and recombined with the direct signal. In addition to the combfilter effect described above, the delay modulation in these effects causes a perceived pitch shift which, when mixed with the direct 18 EMX512SC/EMX312SC/EMX212S signal, results in a harmonically rich swirling or swishing sound. The difference between chorus and flanging effects is primarily in the amount of delay time and feedback used – flanging uses longer delay times than chorus, whereas chorus generally uses a more complex delay structure. Chorus is most often used to thicken the sound of an instrument, while flanging is usually used as an outright “special effect” to produce otherworldly sonic swoops. Compression Have you ever wondered why professionally produced recordings sound so different from your own? There are numerous reasons, of course, but one important factor is the judicious use of compression. One form of compression known as “limiting” can, when properly used, produce a smooth, unified sound with no excessive peaks or distortion. Compression can also be used within a mix to make a voice or instrument seem to come forward, or simply to even out level differences. Compression can be used to make a mix seem bigger and louder by producing a more “saturated” sound. Professional compressors have numerous parameters that need to be carefully adjusted: attack, release, threshold, level, and sometimes more. A professional sound engineer might need to spend a considerable amount of time, based on a considerable amount of experience, to set each of these parameters to achieve the desired sound. The EMX compressor makes achieving great sound much easier. All you need to do is set a single “compression” control and all of the pertinent parameters are automatically adjusted for you. The engineers who designed this fine compressor paid careful attention to achieving the best sound quality possible so that you can quickly achieve pro-quality compression without having to OUTPUT (Min) (Max) INPUT  BASIC Making the Most of Your Mixer worry about a confusing multitude of settings. A common example of the use of compression is to “tame” a vocal that has a wide dynamic range in order to tighten up the mix. With the right amount of compression you’ll be able to clearly hear whispered passages while passionate shouts are still well balanced in the mix. Compression can also be valuable on bass guitar, producing a smooth bass sound that stays solid through the tune. Compression can also be applied to guitar tracks to add extra sustain. Too much compression can be a cause of feedback, however, so use it sparingly. Music First—Then Mix In any case, the music comes first. Think about the music and let it guide the mix, rather than trying to do things the other way around. What is the music saying and what instrument or technique is being used to drive the message? That’s where the focus of your mix should be. You’re using a high-tech tool to do the mixing, but the mix itself is as much art as the music. Approach it that way and your mixes will become a vital part of the music. EMX512SC/EMX312SC/EMX212S 19  Controls and Connectors Controls and Connectors Controls on Each Channel 1 FCL (Feedback Channel Locating) lamp Channels 1 to 4 (Monaural) 1 Channels 5/6 and 7/8 (Stereo) 1 Channels 9/10 and 11/12 (Stereo) 1 This lamp is used during setup to identify any channel that might be howling. Check these lamps when setting up for a performance. If the lamp lights up, adjust the channels equalizer 2 or level knob 5 to reduce the level so that the lamp goes off. NOTE 2 Equalizer (HIGH, MID, and LOW) 2 3 3 3 4 4 4 5 Input of a continuous sound (as from a CD player or vocal) may cause the lamp to come on even in the absence of howling. 5 5 This three-band equalizer adjusts the channel’s high, mid, and low frequency bands. Setting the knob to the position produces a flat frequency response. Turning the knob to the right boosts the corresponding frequency band, while turning to the left attenuates the band. The following table shows the equalization type, the base frequency, and the maximum cut/boost for each of the three bands. Band Type Base Frequency HIGH Shelving 10 kHz MID Peaking 2.5 kHz LOW Shelving 100 Hz Maximum Cut/Boost ±15 dB 3 MONITOR control 6 7 9 8 Adjusts the level of the signal sent from the channel into the MONITOR bus. If input is from a stereo channel pair (5/6, 7/8, 9/10, or 11/12), the signals from the L and R channels are mixed before moving into the bus. The MONITOR bus signal is output at the MONITOR OUT jack O, and may also be output from the SPEAKERS A jacks V (depending on the setting of the POWER AMP switch R). NOTE The channel’s LEVEL knob 5 has no effect on the level of the signal sent into the MONITOR bus. 4 EFFECT knob Adjusts the level of the signal sent from the channel into the EFFECT bus. If input is from a stereo channel pair (5/6, 7/8, 9/10, or 11/12), the signals from the L and R channels are mixed before moving into the bus. The EFFECT bus signal is fed both to the internal digital effector and to the EFFECT OUT jack C. NOTE The channel’s LEVEL knob 5 also affects the level of the channel’s signal into the EFFECT bus. 5 LEVEL knob Adjusts the signal’s output level. Use these knobs to adjust the volume balance among the various channels. NOTE 20 EMX512SC/EMX312SC/EMX212S To reduce noise, set the knobs for unused channels to “0”.  Controls and Connectors 6 COMP knob (EMX512SC and EMX312SC only) This knob adjusts the level of compression applied to the channel. As the knob is turned to the right, the mixer automatically raises the compression ratio while adjusting the output gain accordingly. The result is a narrower, more even dynamic range, as louder signals are softened while the overall level is boosted. Avoid setting the knob too high, however, as excess compression may lead to howling. 9 LINE and MIC jacks (Channels 5/6 to 11/12) These jacks accept stereo inputs. Use these to connect up stereo output devices, such as stereo synthesizers and CD players. LINE jacks: Unbalanced stereo inputs. On channel pairs 5/6 and 7/8 these are phone jacks; on channel pairs 9/10 and 11/12 they are RCA pin jacks. MIC jack: 7 LINE/MIC switch (Channels 1 to 4) Set this switch to match the type of input signal you are supplying—either a mic-level (low level) signal or a line-level (high level) signal. Set the switch to LINE ( ) if you are connecting a line-level source, such as a keyboard or audio device. Set it to MIC ( ) if you are connecting up a microphone or other mic-level source. To avoid damage to speakers, be sure to turn off the power to the EMX itself and to any other power amplifiers and power speakers before setting this switch to LINE or MIC. We also recommend that you turn all output controls (LEVEL knobs, MASTER knobs, etc.) to minimum settings before operating the switch, to avoid risk of loud noises that could cause hearing loss or device damage. NOTE XLR balanced stereo mic-level input jack. If you are connecting a condenser microphone, be sure to turn the PHANTOM switch P to its ON position. • If you wish, you may use the channel pair’s LINE and MIC jacks together at the same time. But note that the levels cannot be adjusted independently. • Signals into LINE L and LINE R jacks are sent independently to the corresponding MAIN L and R buses. • The signal into a MIC jack is sent in equal levels to the MAIN L and MAIN R buses. 8 INPUT A and INPUT B jacks (Channels 1 to 4) You can connect an input source to either jack. Be sure to set the LINE/MIC switch 7 to match the type of device you are connecting. INPUT A: TRS phone-type balanced line input (T: hot, R: cold, S: ground). Accepts both balanced and unbalanced line input. R: Cold (–) S: Ground INPUT B: T: Hot (+) XLR balanced mic input (1: ground, 2: hot, 3: cold). If you are connecting a condenser microphone, be sure to turn the PHANTOM switch P to its ON position. Cold (–) Ground NOTE Hot (+) • You cannot use both jacks at the same time. • The signal into an INPUT jack is sent in equal levels to the MAIN L and MAIN R buses. EMX512SC/EMX312SC/EMX212S 21  Controls and Connectors Digital Effects Section No. Program Parameter 9 KARAOKE ECHO DELAY TIME 0 VOCAL ECHO DELAY TIME A CHORUS 1 LFO FREQ B CHORUS 2 LFO FREQ C FLANGER LFO FREQ D PHASER LFO FREQ E AUTO WAH LFO FREQ F DISTORTION DRIVE A PARAMETER knob Adjusts the parameter (depth, speed, etc.) associated with the selected effect type. 0 NOTE A B The mixer saves the last value used with each effect type. When you change to a different effect type, the mixer automatically restores the value that was previously used with that type (regardless of the current position of the PARAMETER knob). But note that all values return to their defaults at power-off. B ON switch Switches use of the internal effector on or off. The internal effect is applied only if this switch is on. Note that the lamp above the switch lights up orange to indicate that the switch is on. As an alternative to the ON switch, you can use a separately sold FC5 foot switch to toggle the effector on and off. C NOTE D The internal effector is automatically turned on whenever you switch on the mixer’s power. C EFFECT OUT jack This unbalanced phone output jack outputs the signal from the EFFECT bus. You can use this jack to output the signal to an external effector. You can then return the signal by connecting the external effector to any of the LINE jacks on channel pairs 5/6 to 11/12. 0 PROGRAM dial Selects the type of effect to be used. You can select from 16 different effect types, as follows. 22 No. Program Parameter 1 REVERB HALL 1 REVERB TIME 2 REVERB HALL 2 REVERB TIME 3 REVERB ROOM 1 REVERB TIME 4 REVERB ROOM 2 REVERB TIME 5 REVERB STAGE 1 REVERB TIME 6 REVERB STAGE 2 REVERB TIME 7 REVERB PLATE REVERB TIME 8 DRUM AMBIENCE REVERB TIME EMX512SC/EMX312SC/EMX212S If you are returning a signal from an external effector into a LINE jack on any channel pair 5/6 to 11/12, please be sure to turn the EFFECT knob for that channel pair to “0”. D FOOT SW jack This phone input jack can connect to the (separately sold) YAMAHA FC5 foot switch. With the foot switch connected, you can use your foot to toggle the internal effector ON and OFF.  Controls and Connectors MAIN Section E Graphic Equalizer This 7-band graphic equalizer adjusts the frequency characteristics of the stereo signal on the MAIN L and MAIN R buses. This is the signal that is output to the MAIN OUT jacks I and to the SPEAKERS jacks V. Each band can be adjusted by ±12 dB. The base frequencies for the bands are: 125, 250, 500, 1k, 2k, 4k and 8k Hz. F EFFECT RETURN knob Adjusts the level of the signal sent from the internal effector to the MAIN L and MAIN R buses. G MASTER knob E H Adjusts the level of the signal output to the SPEAKERS jacks V and MAIN OUT jacks I. H LEVEL meters The L and R meters show the level of the signal output from the MAIN OUT jack I. F The MAIN OUT signal also passes through the internal power amp and is then output at the SPEAKERS jacks V. Keep an eye on the LIMITER lamps Q to ensure that the level at the SPEAKERS jacks does not stay too high. G I MAIN OUT L and R jacks J I These unbalanced phone output jacks feed out the main stereo output. You would typically connect these jacks to a power amp or powered speakers. The signal sent to these jacks is adjusted by the MAIN section’s MASTER knob G and graphic equalizer E. J REC OUT L and R jacks These RCA pin-type unbalanced output jacks can be used to send the main stereo signal to an external DAT recorder or cassette recorder. Note that unlike the output from the MAIN OUT jacks, the signal from the REC OUT jacks is not adjusted by the MAIN section’s MASTER knob G and graphic equalizer E. NOTE Since this output signal is not adjusted by the MAIN section’s MASTER knob G, you should adjust the level as necessary at the recording side. EMX512SC/EMX312SC/EMX212S 23  Controls and Connectors MONITOR Section K Graphic Equalizer K N This 7-band graphic equalizer adjusts the frequency characteristics of the monitor signal that feeds to the MONITOR OUT jack O and (if the POWER AMP switch is down) to the SPEAKERS B jacks V. Each band can be adjusted by ±12 dB. The base frequencies for the bands are: 125, 250, 500, 1k, 2k, 4k, and 8k Hz. L EFFECT RETURN knob M L Adjusts the level of the signal sent from the internal effector to the MONITOR bus. M MASTER knob Adjusts the level of the monitor signal send to the MONITOR OUT jack O and (if the POWER AMP switch is down) to the SPEAKERS B jacks V. N LEVEL meters The L and R meters show the level of the signal output from the MONITOR OUT jack O. If the POWER AMP switch is down, the MONITOR OUT signal also passes through the internal power amp and is then output at SPEAKERS jacks B1 and B2 V. Keep an eye on the LIMITER lamps Q to ensure that the level at the SPEAKERS jacks does not stay too high. O MONITOR OUT jack O 24 EMX512SC/EMX312SC/EMX212S This unbalanced phone jack outputs the monaural monitor signal. You would typically connect this jack to powered speakers used for monitoring. The signal sent to this jack is adjusted by the MONITOR section’s MASTER knob M and the settings of the MONITOR section’s graphic equalizer K.  Controls and Connectors POWER Section • P Q R To avoid damage to speakers, be sure to turn off the power to the EMX itself and to any other power amplifiers and power speakers before switching phantom power on or off. We also recommend that you turn all output controls (LEVEL knobs, MASTER knobs, etc.) to minimum settings before operating the switch, to avoid risk of loud noises that could cause hearing loss or device damage. Q LIMITER lamps The lamp lights up when the amplified signal being output at the corresponding SPEAKERS jack hits its maximum value. The lamp indicates that the limiter has come on. If the lamps are flashing frequently, the load on the amp is too high and there is risk of damage to your equipment. Reduce the setting of the MASTER knobs (G and M) until the lamps flash only briefly or not at all. S T U R POWER AMP switch Selects the output that gets sent to the SPEAKERS jacks, as follows. Up (MAIN L/R): SPEAKERS jacks A1 and A2 output the signal from the MAIN L bus, and SPEAKERS jack B1 and B2 output the signal from the MAIN R bus. The MAIN section’s MASTER knob G adjusts the output level at all of the SPEAKERS jacks. Down (MAIN(L+R)/MON): SPEAKERS jacks A1 and A2 output a mix of the signals from the MAIN L and MAIN R buses. SPEAKERS jacks B1 and B2 output the signal from the MONITOR bus. The MAIN section’s MASTER knob G adjusts the level to the A jacks, while the MONITOR section’s MASTER knob M adjusts the level to the B jacks. S YS Processing switch P PHANTOM switch This switch toggles +15V phantom power on and off. If you set the switch on, the mixer supplies power to the XLR mic input jacks on all channels (the INPUT B jacks on channels 1 to 4, and the MIC jacks on channel pairs 5/6 to 11/12). Set this switch on when using one or more condenser microphones. When this switch is on, the mixer supplies DC +15V power to pins 2 and 3 of all XLR input jacks. NOTE This switch turns Yamaha Speaker Processing on or off. The processor adjusts the speaker’s bass ranges so as to compensate, for example, for lack of subwoofers. Note however that the resulting frequency balance will vary according to the speakers you are using. T STAND-BY switch This switch mutes the input to channels 1 to 8. The switch lights up to indicate that the mute has been turned on. Note that the mute does not work on channels 9 to 12. NOTE • • Be sure to leave this switch off if you do not need phantom power. When using phantom power, do not connect any devices other than condenser microphones to the XLR input jacks. Other devices may be damaged if connected to phantom power. This precaution does not apply to balanced dynamic microphones, however, as these will not be affected by phantom power. When using the mixer for live performances, you can fill in gaps in the performance by turning on the standby switch and feeding background music from a CD player or other such device into channels 9 to 12. U POWER switch and lamp This switch turns the EMX power ON and OFF. The lamp lights up to indicate that the power in on. Before turning the power ON or OFF, be sure to turn both MASTER knobs (G and M) to “0”. EMX512SC/EMX312SC/EMX212S 25  Controls and Connectors Rear Panel W V X V SPEAKERS jacks W AC IN connector Use these jacks to connect to speakers. Note that the output directed to these jacks varies according to the setting of the POWER AMP switch R. Connects to the included power cord. Connect one end of the cord to this connector, and then plug the other end into a standard power outlet. A1, B1: Neutrik NL4 Speakon outputs. Polarities are as shown below. Please use the cord that comes with the mixer. Use of a different cord may pose risk of fire, burns, or equipment damage. 1- 1+ Neutrik Plug A1 and B1 Connectors 1+ + 1– – 2+ 2+ 2- 2– A2, B2: Phone output jacks. 26 EMX512SC/EMX312SC/EMX212S X Ground Screw For maximum safety be sure to securely connect the EMX to an earth connection. The supplied power cable has a three-prong plug that will ground the unit when the plug is inserted into an appropriately grounded three-prong type AC mains outlet. If the AC outlet is not grounded, be sure to ground the unit by using this ground screw. Correct grounding will effectively eliminate hum noise and interference.  Connecting Speakers Connecting Speakers When making 2-channel and 2-channel parallel connections to the SPEAKERS jacks, be sure that the impedance of your speakers meets the conditions indicated below. Note that actual speaker impedance varies according to connection method and number of speakers. When making connections, be sure that your cables have the appropriate ratings and the correct plugs. Be sure to use dedicated speaker cables when connecting speakers to the SPEAKERS jacks. ■ 2-channel connection ■ 2-channel parallel connection When connecting by 2-channel connection, use speakers with impedance of 4 ohms to 8 ohms. When connecting speakers in parallel as shown below, use speakers with impedance of 8 ohms to 16 ohms. 4Ω to 8Ω 4Ω to 8Ω 8Ω to 16Ω 8Ω to 16Ω 8Ω to 16Ω 8Ω to 16Ω EMX512SC/EMX312SC/EMX212S 27  Horizontal Orientation, Tilting and Rack Mounting Horizontal Orientation, Tilting and Rack Mounting Horizontal Orientation If you are going to position the EMX unit horizontally, be sure to attach the included rubber stabilizers before use. The stabilizers prevent the unit from tipping over. NOTE Please detach the stabilizers when transporting the unit. ■ How to attach the rubber stabilizers 1 Turn the EMX unit upside down. 2 Attach the two rubber stabilizers that were included with the unit. Push each stabilizer all the way in so that they are firmly in place. stabilizer 28 EMX512SC/EMX312SC/EMX212S 3 Turn the EMX right-side up.  Horizontal Orientation, Tilting and Rack Mounting Tilting You can set the EMX unit at an angle, as shown below. Do not push too forcefully when tilting the unit. Excess force may cause the unit to topple or turn, potentially resulting in equipment damage or in injury to bystanders. Rack Mounting To prepare the unit for rack mounting, use the (separately sold) RK512 rack mount kit. If rack-mounting the unit, be sure to maintain adequate ventilation so the unit does not overheat. Consider attaching a vent panel, and do not use a sealed rack. NOTE The EMX unit requires 7U of rack space. RK512 Rack mount Kit 2 Using the kit’s 4 screws, attach the kit’s 2 metal fittings as shown below. 3 Turn the EMX right-side up. Screws Fittings ■ How to install the rack-mount hardware 1 Turn the EMX unit upside down. EMX512SC/EMX312SC/EMX212S 29  Setting Up Setting Up Top panel NOTE In most cases it is sufficient to connect speakers to the SPEAKERS jacks on the unit’s rear panel. But if you want even more output, you can get it by connecting a power amp to the MAIN OUT or MONITOR OUT jack, and then connecting speakers to the power amp. Guitar Speakers CD, Cassette, or DAT Recorder Synthesizer ASSIGN A PAN/SEND ASSIGN TONE ASSIGN B PAN REVERB CUTOFF RESONANCE SWING GATE TIME ASSIGN 1 CHORUS ASSIGN 2 TEMPO ATTACK RELEASE VELOCITY UNITMULTIPLY REMOTE ON / OFF ARPEGGIO R-AUDIO G-MIDI Integrated Sampling Sequencer / Modular Synthesis Plug-in System / Real-time External Control Surface ON / OFF MUSIC PRODUCTION SYNTHESIZER PRE 1 KNOB CONTROL FUNCTION KN 1 LOW KN 2 LOW MID KN 3 HIGH MID KN 4 HIGH VOLUME 1 VOLUME 2 VOLUME 3 VOLUME 4 BYPASS INSERTION SYSTEM PRE 2 PRE 3 PRE 4 MODE EFFECT ÊARP FX MASTER EFFECT VOICE PERFORM SLOT 1 DRUM KITS MASTER PRE 5 PRE 6 USER 1 USER 2 GM PLG 1 GUITAR/ PLUCKED BASS STRINGS SLOT 2 SLOT 3 PLG 2 PLG 3 BRASS REED/PIPE CATEGORY SEARCH BANK EQ FAVORITES A. PIANO KEYBOARD ORGAN SEQUENCER SONG PATTERN INTEGRATED SAMPLING MIXING EDIT JOB A FILE SEQ TRANSPORT DEC/NO INC / YES SYN LEAD DEMO UTILITY 1 SCENE SF2 SF1 LOCATE 1 SF3 SF4 B C SYN PAD/ CHOIR SYN COMP 2 D E DRUM/ CHROMATIC PERCUSSION PERCUSSION 3 F G H SE MUSICAL FX COMBI SECTION 4 5 6 7 8 TRACK SELECT 12 13 14 15 16 MUTE GROUP INFORMATION SF5 2 ELEMENT/PERF. PART/ZONE COMMON COMPARE OCTAVE DOWN STORE F1 F2 F3 F4 F5 F6 SCENE STORE SET LOCATE EXIT ENTER EXECUTE 9 10 11 NUMBER SOLO UP MASTER VOLUME CS 1 CS 2 CS 3 CS 4 ZONE 1 ZONE 2 ZONE 3 ZONE 4 CD Player DI Bass Power Amp Foot Switch (YAMAHA FC5) Microphones Microphones Monitor Speakers Drums Rear Panel EMX Installation Intake At least 10 cm Exhaust At least 25 cm Vents are located on the sides and rear of the EMX unit. Position the unit so that the vents are not blocked by nearby walls or objects. 30 EMX512SC/EMX312SC/EMX212S  Troubleshooting Troubleshooting ■ Power doesn’t come on. ❑ Be sure that you are using the supplied power cord, and that it is correctly connected to the AC IN connector and plugged into a working power outlet. ■ Power suddenly went off. ❑ Check whether the vents at the sides and rear of the unit are blocked. The EMX unit may overheat if the vents are blocked. If the unit overheats, the power may automatically go off. Wait for the unit to cool down, and then turn the power back on. ■ Sound suddenly ❑ Check whether the vents at the sides and rear of the unit are blocked. The EMX unit may overheat if the vents are blocked. If the unit overheats, it may cut off the output to the internal amp until things cool down. stopped. ■ No sound. ❑ Are microphones, external devices, and speakers connected correctly? ❑ Are the channel LEVEL knobs and the two MASTER knobs set to appropriate levels? ❑ Is the POWER AMP switch set correctly? When outputting a stereo signal, set it to the up (MAIN L/R) position. ❑ Check that the speaker cables are not shorted. ❑ If the above checks do not identify the problem, call Yamaha for service. (Refer to the end of this manual for a list of Yamaha dealers.) ■ Sound is faint, distorted, ❑ Check that the channel LEVEL knobs and the two MASTER knobs are set appropriately. ❑ Check that the LINE/MIC switches on channels 1 to 4 are set correctly. ❑ On channels 1 to 4, be sure that you have not connected to both INPUT A and INPUT B. On each of these channels you may use one input or the other, but not both. ❑ Is the input signal from the connected device set to an appropriate level? or noisy. ■ An FCL lamp comes even though there is no howling on the channel. ■ Can’t hear the internal digital effect. ■ The sound from the speakers seems dull. I want a more forceful sound. ■ I want spoken words to be heard more clearly. ■ I want to listen to monitor output. ❑ Input of a continuous sound (from a CD player or other such source) may cause the lamp to come on even in the absence of howling. ❑ Check that the EFFECT knob on each channel is correctly adjusted. ❑ Be sure that the internal effector’s ON switch is turned on. ❑ Be sure that the EFFECT RETURN knobs in the MAIN and MONITOR sections are correctly adjusted. ❑ Try turning on the YS Processing switch. ❑ Adjust the equalizers (HIGH, MID, and LOW knobs) on each channel. ❑ Adjust the graphic equalizers. ❑ Be sure that the YS Processing switch is turned off. ❑ Adjusting the equalizers (HIGH, MID, and LOW knobs) on each channel. ❑ Adjusting the graphic equalizers. ❑ Connected a powered speaker to the MONITOR OUT jack. Then adjust the MONITOR OUT signal by adjusting the channel MONITOR knobs and the MONITOR section’s MASTER knob. ❑ If you want to send the monitor signal to SPEAKERS jacks B1 and B2, set the POWER AMP switch to the down position (to MAIN(L+R) / MON). Note that in this case the B jacks will output the monitor signal, and the A jacks will output a mix of the MAIN L and MAIN R signals. EMX512SC/EMX312SC/EMX212S 31  Specifications Specifications ■ General Specifications Output EMX512SC Maximum Output Power SPEAKERS OUT EMX312SC EMX212S Input Frequency Response Maximum Voltage Gain@ 1 kHz CH INPUT 1-11/12 CH 1-4 INPUT B, CH 5/6-11/12 MIC RL 4Ω 8Ω 4Ω 8Ω 4Ω 8Ω Output MAIN OUT, MONITOR OUT, EFFECT OUT, REC OUT SPEAKERS OUT MAIN OUT, MONITOR OUT MAIN OUT CH 1-4 INPUT B, CH 5/6-11/12 MIC Gain Error @ 1 kHz MONITOR OUT EFFECT OUT REC OUT It measures in each CH unit. CH 1-4 INPUT A MAIN OUT Conditions Both ch drive, 1 kHz, THD+N =< 0.5% RL It measures in each CH unit. Conditions 10 kΩ CH1-4 MIC/LINE: MIC 20 Hz-20 kHz, 0 dB 4 Ω @ 1 kHz Rs=150 Ω CH1-4 10 kΩ MIC/LINE:MIC Input level:–60 dBu CH1-4 MIC/LINE:MIC Input level:–60 dBu CH1-4 MIC/LINE:MIC Input level:–60 dBu CH1-4 MIC/LINE:MIC level:–60 dBu 10 kΩ Input CH1-4 MIC/LINE:MIC Input level:–50 dBu MIC/LINE:MIC CH 5/6-7/8 LINE MAIN OUT (Phone) CH 9/10-11/12 LINE MAIN OUT (Pin) Total Harmonic Distortion MIN US 500 350 300 190 220 130 AU 500 350 300 190 220 130 EU 500 320 300 180 220 130 UNIT MIN TYP MAX UNIT –3.0 0.0 1.0 –3.0 0.0 1.0 65 4.0 6.0 2.0 4.0 6.0 –8.0 –6.0 –4.0 –12.0 –10.0 –8.0 2.0 4.0 6.0 Input level:–20 dBu 2.0 4.0 6.0 Input level:–20 dBu 2.0 4.0 6.0 MAIN OUT, MONITOR OUT, EFFECT OUT, REC OUT dBu @ 20 Hz, 10 kΩ +14 1 kHz, 20 kHz CH 1-4 INPUT B, CH 5/6-11/12 MIC MAIN OUT CH INPUT 1-11/12 MAIN OUT, MONITOR OUT, EFFECT OUT EIN, Rs=150 Ω CH1-4 MIC/LINE:MIC 10 kΩ Output Noise Rs=150 Ω CH1-4 MIC/LINE:MIC MAIN OUT L, R MONITOR OUT SPEAKERS OUT 10 kΩ Master control at minimum. 4Ω dB dB 2.0 CH INPUT 1-11/12 W 0.5 dBu dBV dBu % (THD+N) Hum & Noise (20 Hz-20 kHz) It measures in each CH unit. EIN=Equivalent Input Noise Residual Output Noise (20 Hz-20 kHz) — Input Crosstalk @ 1 kHz It measures in each CH unit. Phantom Voltage It measures in each CH unit. CH & ST CH Equalization Internal Digital Effect Level Meters FCL Sensitivity Protection 32 CH1-4 Output CH 1-4 INPUT B, CH 5/6-11/12 MIC Output Adjacent CH inputs Conditions –115 dBu –50 –90 –90 –65 MIN TYP Input to Output (LEVEL controls: minimum) MAIN OUT — — No load MAX –65 –65 UNIT dB MIN TYP MAX UNIT 14 15 16 V HIGH Turn over /roll-off frequency of 10 k (shelving) shelving :3dB below maximum MID 2.5 k (peaking) variable level. LOW ±15dB maximum 100 (shelving) 16 programs Parameter control FOOT SW ON/OFF 2 × 5-points LED level meter [MAIN(L,R)], 5-points LED level meter [MONITOR] +6, +3, 0, –5, –10 [dB] Input signal level => –75dBu: LED on, CH1-4 MIC/LINE:MIC B Input, CH 5/6-11/12 MIC Input POWER switch on/off mute DC-fault :power supply shutdown /manual reset Power Amplifier Thermal /heatsink temp => 90˚C:output mute /auto reset Vl limiter /RL =< 2 Ω Clip limiter /THD => 1 %, Indicator × 2 Power Supply Thermal /heatsink temp => 100˚C :power supply shutdown /manual reset EMX512SC/EMX312SC/EMX212S dBu Hz  Specifications MIN EMX512SC EMX312SC EMX212S Length Height Depth Width Power Consumption AC Cord Dimensions 2450 Net Weight TYP 500 450 300 2500 284 264 442.5 8 MAX UNIT W 2550 mm mm kg Power cord, Rubber stabilizers × 2, Owner’s Manual RACK MOUNT KIT (RK512), FOOT SW (FC5) Included Accessories Options Note: All level control normally: Maximum level, Output impedance of signal generator :150 ohm ■ Input Characteristics Input Terminals MIC/LINE Actual Load Impedance For Use with Nominal MIC XLR 2 kΩ 50–600 Ω Mics 6 kΩ 600 Ω Lines LINE CH INPUT 1-4 MIC Phone LINE CH INPUT 5/6, 7/8 CH INPUT 9/10, 11/12 Input Level Sensitivity *2 Nominal (▼ position) Max. before Clip –60 dBu (0.775 mV) –35 dBu (13.8 mV) –15 dBu (138 mV) –30 dBu (24.5 mV) –5 dBu (436 mV) +15 dBu (4.36 V) –50 dBu (2.45 mV) –25 dBu (43.6 mV) –5 dBu (436 mV) –20 dBu (77.5 mV) +5 dBu (1.38 V) +25 dBu (13.8 V) Connector XLR-3-31 type *3 Phone Jack *4 XLR — 2 kΩ 50–600 Ω Mics –60 dBu (0.775 mV) –35 dBu (13.8 mV) –15 dBu (138 mV) XLR-3-31 type *3 Phone — 10 kΩ 600 Ω Lines –20 dBu (77.5 mV) +5 dBu (1.38 V) +25 dBu (13.8 V) Phone Jack *5 XLR — 2 kΩ 50–600 Ω Mics –60 dBu (0.775 mV) –35 dBu (13.8 mV) –15 dBu (138 mV) XLR-3-31 type *3 Pin — 10 kΩ 600 Ω Lines –20 dBu (77.5 mV) +5 dBu (1.38 V) +25 dBu (13.8 V) RCA Pin Jack *1 0 dBu is referenced to 0.775 Vrms. *2 Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V), or the nominal output level when the unit is set to maximum level. (All level controls are at maximum position.) *3 XLR-3-31 type connectors are balanced. (1=GND, 2=HOT, 3=COLD) *4 Phone Jacks are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND) *5 Phone Jacks are unbalanced. ■ Output Characteristics Output Level Output Terminals Actual Source Impedance For Use with Nominal SPEAKERS [A1, A2, B1, B2] 0.1 Ω 4 Ω Speakers EMX212S 50 W 220 W MAIN OUT [L, R] 600 Ω 10 kΩ Lines — +4 dBu (1.23 V) +20 dBu (7.75 V) Phone Jack *2 EFFECT OUT 600 Ω 10 kΩ Lines — +4 dBu (1.23 V) +20 dBu (7.75 V) Phone Jack *2 MONITOR OUT 600 Ω 10 kΩ Lines — +4 dBu (1.23 V) +20 dBu (7.75 V) Phone Jack *2 –10 dBV (316 mV) +10 dBV (3.16 V) RCA Pin Jack Nominal Max. before Clip EMX512SC 125 W 500 W EMX312SC 75 W 300 W REC OUT [L, R] 600 Ω 10 kΩ Lines — *1 0 dBu is referenced to 0.775 Vrms. 0 dBV is referenced to 1 Vrms. *2 Phone Jacks are unbalanced. Connector [A1, B1] SPEAKON [A2, B2] Phone Jack Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. EMX512SC/EMX312SC/EMX212S 33  Specifications 264 Dimensional Diagrams 442.5 2 286 440 284 2.5 307.8 66.1 71 298 71 108 54 66.1 Unit: mm 34 EMX512SC/EMX312SC/EMX212S  Specifications Block Diagram and Level Diagram EMX512SC/EMX312SC/EMX212S 35  For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A. Tel: 714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. MALTA ASIA Olimpus Music Ltd. The Emporium, Level 3, St. Louis Street Msida MSD06 Tel: 02133-2144 THE PEOPLE’S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co.,Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: 021-6247-2211 THE NETHERLANDS/ BELGIUM/LUXEMBOURG Yamaha Music Europe Branch Benelux Clarissenhof 5-b, 4133 AB Vianen, The Netherlands Tel: 0347-358 040 FRANCE Yamaha Music Europe BP 70-77312 Marne-la-Vallée Cedex 2, France Tel: 01-64-61-4000 BRAZIL Yamaha Musical do Brasil Ltda. Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi, CEP 04534-013 Sao Paulo, SP. BRAZIL Tel: 011-3704-1377 ARGENTINA Yamaha Music Latin America, S.A. Sucursal de Argentina Olga Cossettini 1553, Piso 4 Norte Madero Este-C1107CEK Buenos Aires, Argentina Tel: 011-4119-7000 PANAMA AND OTHER LATIN AMERICAN COUNTRIES/ CARIBBEAN COUNTRIES Yamaha Music Latin America, S.A. Torre Banco General, Piso 7, Urbanización Marbella, Calle 47 y Aquilino de la Guardia, Ciudad de Panamá, Panamá Tel: +507-269-5311 PT. Yamaha Musik Indonesia (Distributor) PT. Nusantik Gedung Yamaha Music Center, Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: 021-520-2577 EUROPE THE UNITED KINGDAM/IRELAND Yamaha Music Europe GmbH (UK) Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, England Tel: 01908-366700 GERMANY Yamaha Music Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: 04101-3030 SWITZERLAND/LIECHTENSTEIN Yamaha Music Europe GmbH Branch Switzerland in Zürich Seefeldstrasse 94, 8008 Zürich, Switzerland Tel: 044-387-8080 AUSTRIA/BULGARIA Yamaha Music Europe GmbH Branch Austria Schleiergasse 20, A-1100 Wien, Austria Tel: 01-60203900 CZECH REPUBLIC/HUNGARY/ ROMANIA/SLOVAKIA/SLOVENIA Yamaha Music Europe GmbH Branch Austria (Central Eastern Europe Office) Schleiergasse 20, A-1100 Wien, Austria Tel: 01-602039025 POLAND/LITHUANIA/LATVIA/ESTONIA Yamaha Music Europe GmbH Branch Sp.z o.o. Oddzial w Polsce ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland Tel: 022-500-2925 PA30 Yamaha Music Europe GmbH, Branch Italy Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 KOREA SPAIN/PORTUGAL Yamaha Music Europe GmbH Ibérica, Sucursal en España Ctra. de la Coruna km. 17, 200, 28230 Las Rozas (Madrid), Spain Tel: +34-902-39-8888 GREECE Philippos Nakas S.A. The Music House 147 Skiathou Street, 112-55 Athens, Greece Tel: 01-228 2160 Yamaha Music Europe GmbH, Tyskland – filial Denmark Generatorvej 6A, DK-2730 Herlev, Denmark Tel: 44 92 49 00 Yamaha Music (Russia) Room 37, bld. 7, Kievskaya street, Moscow, 121059, Russia Tel: 495 626 5005 OTHER EUROPEAN COUNTRIES Yamaha Music Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: +49-4101-3030 AFRICA Yamaha Corporation, Asia-Pacific Sales & Marketing Group Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2303 MIDDLE EAST TURKEY/CYPRUS Yamaha Music (Malaysia) Sdn., Bhd. Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 03-78030900 TAIWAN DENMARK RUSSIA MALAYSIA Yamaha Music (Asia) PRIVATE LIMITED Blk 202 Hougang Street 21, #02-00, Singapore 530202, Singapore Tel: 6747-4374 Yamaha Music Europe GmbH Germany filial Scandinavia J. A. Wettergrens Gata 1, Box 30053 S-400 43 Göteborg, Sweden Tel: 031 89 34 00 Yamaha Music Europe GmbH Germany Norwegian Branch Grini Næringspark 1, N-1345 Østerås, Norway Tel: 67 16 77 70 Yamaha Music Korea Ltd. 8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong, Kangnam-Gu, Seoul, Korea Tel: 02-3467-3300 SINGAPORE SWEDEN/FINLAND/ICELAND NORWAY Yamaha Music India Pvt. Ltd. Spazedge building, Ground Floor, Tower A, Sector 47, Gurgaon- Sohna Road, Gurgaon, Haryana, India Tel: 0124-485-3300 INDONESIA ITALY Yamaha de México S.A. de C.V. Calz. Javier Rojo Gómez #1149, Col. Guadalupe del Moral C.P. 09300, México, D.F., México Tel: 55-5804-0600 INDIA Yamaha KHS Music Co., Ltd. 3F, #6, Sec.2, Nan Jing E. Rd. Taipei. Taiwan 104, R.O.C. Tel: 02-2511-8688 THAILAND Siam Music Yamaha Co., Ltd. 4, 6, 15 and 16th floor, Siam Motors Building, 891/1 Rama 1 Road, Wangmai, Pathumwan, Bangkok 10330, Thailand Tel: 02-215-2622 OTHER ASIAN COUNTRIES Yamaha Corporation, Asia-Pacific Sales & Marketing Group Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2303 OCEANIA AUSTRALIA Yamaha Music Australia Pty. Ltd. Level 1, 99 Queensbridge Street, Southbank, Victoria 3006, Australia Tel: 3-9693-5111 COUNTRIES AND TRUST TERRITORIES IN PACIFIC OCEAN Yamaha Corporation, Asia-Pacific Sales & Marketing Group Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2303 Yamaha Music Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: 04101-3030 OTHER COUNTRIES Yamaha Music Gulf FZE LOB 16-513, P.O.Box 17328, Jubel Ali, Dubai, United Arab Emirates Tel: +971-4-881-5868 HEAD OFFICE Yamaha Corporation, Pro Audio Division Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2441 Yamaha Pro Audio global web site http://www.yamahaproaudio.com/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ C.S.G., Pro Audio Division © 2005-2012 Yamaha Corporation WE29640 202CRAP*.*-**F0 Printed in Vietnam