SKY DEVICES EliteD55 Manual de usuario
- Categoría
- Smartphones
- Tipo
- Manual de usuario
D55
Elite
User Manual
Design
To turn on the device, keep the ON button
pressed for a couple of seconds.
1 USB Port 6 Volume +/-
2 Earphone Jack 7 Power key
3 Receiver 8 Microphone
4 Proximity Sensor 9 Rear camera
5 Front camera 10 Speaker
49
10
6
7
12
3 5
8
How to install SIM card and battery
Follow the steps shown on the image located in
the back part. Please note that the device has 2
slots for SIM cards.
Make sure that the back cover is well placed and
closed after you insert the SIM card(s).
How to proceed if the device gets blocked?
1. Press RESET button
2. Press ON button for a couple of
seconds
3. Take out the battery
Charge the battery
Before using the device for the first time or if
the battery has not been used for a long time,
you need to charge the battery.
Use only approved chargers, batteries and
cables. Unapproved chargers or batteries can
damage the battery or the device.
Connect the small end part of the charger to the
device’s multifunction slot and the big end part
of the charger to an electric source.
If you connect the charger in a wrong way, you
can seriously damage the device. The warranty
does not cover damage caused by an
inappropriate use.
After charging is complete, disconnect the
device from the charger. Disconnect first the
charger from the device and then from the
electric source. Do not take out the battery
before disconnecting the charger. This can
damage the device.
The charger does not have ON/OFF button, so,
in order to cut the electrical supply, the end user
should disconnect the charger from the electric
source. Please keep the charging cable close to
the device when it is charging, to avoid it to be
tight. To save energy, disconnect the charger
when it is not in use.
Information about
security
This section contains information about mobile
security. Some content may not apply to your
device. To avoid injury to yourself and others, or
damage to the device, read the safety
information before using the device.
Warning Failure to comply with these rules and
security warnings, the end user could suffer
serious injury or death.
Do not use damaged power cables or
connectors or loose plugs. Insecure connections
can cause electrical shock or fire
Do not touch the power cord with wet hands or
pull the cord to disconnect the charger. Doing
so could end up in electrocution.
Do not bend or damage the power cord. Doing
so could cause electric shock or fire.
Do not touch the power cord with wet
hands or pull the cord to disconnect the
charger. Doing so could cause an electric
shock.
Do not short-circuit the charger or the device.
Doing so could cause electric shock or fire, or
the battery may malfunction or explode.
Do not use the device outdoors during a
thunderstorm. Doing so could cause electric
shock, or the device may malfunction.
Use batteries, chargers, accessories and
supplies approved by the manufacturer.
Do not knock or drop the charger or device.
Handle and dispose of the device and the
charger with caution
Protect the device, battery and charger to
avoid damage
Do not store the device in heaters, microwaves,
hot cooking equipment, or high pressure
containers, or near them
Do not use or store the device in areas with
high concentrations of dust or airborne
materials
Do not bite or suck on the device or battery
Do not insert the device or supplied accessories
into the eyes, ears and mouth
Do not handle damaged batteries lithium ion or
leaking
Do not use the device in a hospital, on a plane
or car that could be interfered with by radio
frequency
Do not expose the device to heavy smoke or
fumes
If you use a hearing aid, contact the
manufacturer for information about radio
interference
Do not use the device near other equipment or
devices emitting radio frequency, such as
sound systems or radio towers
Turn off the device in potentially explosive
environments
If you notice that the device or battery emits
strange smells or sounds, or see smoke or
liquid leaving the device or battery, stop using
the device immediately
Comply with all safety warnings and
regulations regarding the use of mobile devices
while driving
Correct use and maintenance
Keep the device dry
Do not store the device in hot or cold areas.
It is recommended to use the device at
temperatures between 5 ° C and 35 ° C
Do not expose the device to direct sunlight for
long periods (eg on the dashboard of a car)
Do not store your device with metal objects,
such as coins, keys and necklaces
Do not store your device near magnetic fields
Magnetic stripe cards, including credit cards,
phone cards, passbooks, and boarding passes,
may be damaged by magnetic fields.
If the device is heated, discontinue use of the
device or applications for a while
Do not use the device if the back cover is not
installed
If your device has a lamp or a flash for the
camera, do not use near the eyes of people or
pets
Use caution when exposed to flashing
lights
Reduce the risk of repetitive motion
injuries
When using headphones protect your
hearing and ears
Excessive exposure to loud sounds can
cause hearing damage.
Exposure to loud sounds while walking can
distract your attention and cause an
accident.
Always turn the volume down before
plugging the earphones into an audio
source and use the setting necessary to
hear your conversation or music minimum
volume.
Do not carry your device in your back
pockets or around your waist
Do not paint your device or put stickers
Do not use the device if the screen is cracked or
broken
Install mobile devices and equipment with
caution
Do not let the product drop or subject to strong
impact
Ensure maximum duration for battery and
charger
Avoid charging the device for more than a
week, as overcharging may shorten the
battery life.
Over the time, if the device is not used, it
will be discharged and needs to be
recharged to use it
Unplug the charger from the power supply
when not in use.
Protect your personal information and avoid
disclosure or misuse of confidential
information
Do not distribute copyright material by
copyright
Malware and virus
Follow the following tips to protect your
device against malware and viruses.
Otherwise, it may cause damage or loss of
data, which may not be covered by
warranty
Do not download applications from
unknown sources.
Do not enter in unreliable web sites.
Delete suspicious SMS or emails from
unknown senders.
Set up a keyword and change it often.
Unable the wireless functions such as
Bluetooth® when not in use.
Correct disposal of this product
The presence of this symbol on the product,
accessories or literature accompanying
indicates that the product or its electronic
accessories (eg charger, headset , USB cable)
should be disposed of with other household
waste.
To prevent possible harm to the environment or
human health from uncontrolled waste disposal,
separate this from other types of waste and
recycle them. Thus the sustainable reuse of
material resources is promoted.
Household users should contact either the
retailer where they purchased this product or
their local authorities to find out how and where
they can take to be subjected to
environmentally safe recycling.
Business users should contact their supplier and
check the conditions of the purchase contract.
This product and its electronic accessories
should not be mixed with other commercial
waste.
Correct disposal of batteries in this product
The presence of this marking on the battery,
manual or packaging indicates that when
finished the life of the batteries should not be
disposed of with other household waste. The
chemical symbols Hg , Cd or Pb if present,
indicate that the battery contains mercury ,
cadmium or lead above the reference values
allowed by Directive 2006/66 of the
European Union levels. If the batteries are not
properly disposed of, these substances can
cause injuries or damage the environment.
To protect natural resources and to promote
material reuse, please separate batteries from
other waste and recycle them through the
system of free collection locally.
Treatment for common
problems
1. Data erase
To erase information and reset factory data,
please follow these steps: settings – security
copy – reset factory data – accept.
2. No voice in the earphone
Make sure the volume is not turned down all the
way
Unplug the headset. Plug it in again. Make sure
you push connector all the way in.
3. Charging issues
Please make sure the setting of the charger is
according with the device.
Try to charge the Smartphone with another
compatible charger to check where the problem
comes from.
4. Download issues
Make sure it connects with internet properly.
Adjust time and date.
5. Why some of downloaded videos cannot
play normally?
The device is compatible with most of video file
format, but there still have some differences in
format, encoded mode, Resolution and code
rate etc. it could result in some of the videos
cannot play or have play issues. Our suggestion
is that use the three party adapter software for
transforming in the PC then copy to the device.
6. Device crashed or can't turn on
Once device crashed during the running time, It
can be restarted via tap the RESET button,
located at the back or side part of the device.
NOTE:
We are not responsible for any incompatibilities
of use that may be occasionally generated
between applications developed by third parties
and this device.
Consequently, no product returns will be
accepted for this reason.
Manual del Usuario
Diseño
Para encender el dispositivo mantenga
presionado el botón ENCENDIDO durante unos
segundos.
1 Puerto USB 6 Volumen +/-
2 Enchufe de audífonos 7 Tecla encendido
3 Receptor 8 Micrófono
4 Sensor de proximidad 9 Cámara posterior
5 10 Altavoz
Câmera frontal
49
10
6
7
12
3 5
8
Como instalar la tarjeta SIM y la batería
Siga los pasos que se muestran en la imagen
ubicada en la parte posterior. Tenga en cuenta
que el dispositivo tiene 2 ranuras para tarjetas
SIM.
Asegúrese de que la tapa posterior esté bien
colocada y cerrada después de insertar la(s)
tarjeta(s) SIM.
¿Qué hacer si el dispositivo se bloquea?
1. Pulse el botón de RESET
2. Presione el botón de ENCENDIDO
durante un par de segundos.
3. Retire la batería
Cargar la batería
Antes de usar el dispositivo por primera vez o si
la batería no se ha usado por un tiempo
prolongado, debe cargar la batería.
Utilice solo cargadores, baterías y cables
aprobados. El uso de cargadores o baterías no
aprobadas puede dañar la batería o el
dispositivo.
Conecte la parte del extremo pequeño del
cargador a la ranura multifunción del dispositivo
y la parte del extremo más grande del cargador
a una fuente de alimentación eléctrica.
Si conecta el cargador de forma incorrecta,
puede dañar seriamente el dispositivo. La
garantía no cubre daños causados por uso
inapropiado.
Una vez completada la carga, desconecte el
dispositivo del cargador. Desconecte primero el
cargador del dispositivo y luego de la fuente de
alimentación. No retire la batería antes de
desconectar el cargador. Esto puede dañar el
dispositivo.
El cargador no cuenta con un botón de
ENCENDIDO/APAGADO, de manera que el
usuario debe desconectar el cargador de la
fuente de alimentación eléctrica. Mantenga el
cable de carga cerca del dispositivo cuando se
está cargando, para evitar tensión en el cable.
Para ahorrar energía, desconecte el cargador
cuando no esté en uso.
Información sobre
seguridad
Esta sección contiene información sobre la
seguridad del dispositivo. Es posible que parte
del contenido no se aplique a su dispositivo.
Para evitar lesiones o causar daño a otros, o
dañar el dispositivo, lea la información sobre
seguridad antes de su uso.
Advertencia Si no se cumplen estas reglas y
advertencias, el usuario podría sufrir lesiones
graves o la muerte.
No utilice cables o conectores de alimentación
dañados o enchufes sueltos. Las conexiones no
seguras pueden ocasionar un corto circuito o
incendio.
No utilice el cable de alimentación con las
manos mojadas, ni tire el cable para
desconectar el cargador. Al hacerlo podría
recibir una descarga eléctrica.
No doble ni dañe el cable de alimentación.
Hacerlo podría provocar una descarga eléctrica
o un incendio.
No provoque un corto circuito en el cargador o
en el dispositivo. Hacerlo podría provocar una
descarga eléctrica o un incendio o la batería
podría tener un mal funcionamiento o explotar.
No utilice el dispositivo en exteriores durante
una tormenta eléctrica. Hacerlo podría causar
una descarga eléctrica o mal funcionamiento del
dispositivo.
Utilice baterías, cargadores, accesorios y partes
aprobados por el fabricante.
No golpee ni deje caer el cargador o el
dispositivo.
Manipule y deseche el dispositivo y el cargador
con la debida precaución.
Proteja el dispositivo, la batería y el cargador
para evitar daños.
No guarde el dispositivo en calefactores,
microondas, equipos de cocina calientes o
recipientes de alta presión, ni cerca de ellos.
No utilice ni almacene el dispositivo en áreas
con altas concentraciones de polvo o
materiales transportados por el aire.
No muerda ni chupe el dispositivo o la batería.
No inserte el dispositivo o sus accesorios en los
ojos, oídos y boca.
No manipule las baterías de litio ion dañadas o
las posibles fugas.
No utilice el dispositivo en hospitales, aviones
o en automóviles, donde pueda interferir con la
frecuencia de radio.
No exponga el dispositivo a humo o humos
densos.
Si utiliza un aparato auditivo, comuníquese con
el fabricante para obtener información sobre la
interferencia de radio.
No utilice el dispositivo cerca de otros equipos
o dispositivos que emitan frecuencias de radio,
como sistemas de sonido o torres de radio.
Apague el dispositivo en entornos
potencialmente explosivos.
Si observa que el dispositivo o la batería
emiten olores o sonidos extraños, o ve humo o
liquido saliendo del dispositivo o de la batería,
deje de usarlo inmediatamente.
Debe cumplir con todas las advertencias y
normas de seguridad relacionadas con el uso
de dispositivos móviles mientras conduce.
Uso y mantenimiento correctos
Mantenga el dispositivo seco
No almacene el dispositivo en áreas frías o
calientes.
Se recomienda usar el dispositivo a
temperaturas entre 5 ° C y 35 ° C.
No exponga el dispositivo directamente a la luz
solar durante periodos prolongados (por
ejemplo, en el tablero del automóvil).
No guarde el dispositivo junto con objetos
metálicos, como monedas, llaves y collares.
No guarde el dispositivo cerca de campos
magnéticos.
Las tarjetas de banda magnética, incluidas las
tarjetas de crédito, las tarjetas telefónicas, y las
tarjetas de embarque pueden dañarse por los
campos magnéticos.
Si el dispositivo se calienta, deje de usar el
dispositivo o las aplicaciones por un rato.
No utilice el dispositivo si la tapa posterior no
está instalada.
Si su dispositivo cuenta con linterna o flash
para la cámara, no lo use cerca de los ojos de
las personas o mascotas.
Tenga cuidado cuando esté expuesto a
luces intermitentes.
Reduzca el riesgo de lesiones por
movimientos repetitivos.
Cuando utilice audífonos proteja su
audición y oídos.
La exposición excesiva a sonidos fuertes
puede causar daños auditivos.
La exposición a sonidos fuertes mientras
camina puede distraer su atención y causar
un accidente.
Siempre baje el volumen antes de enchufar
los auriculares a una fuente de audio y
utilice la configuración necesaria para
escuchar su conversación o música al
mínimo volumen.
No lleve el dispositivo en el bolsillo trasero
o alrededor de la cintura.
No pinte el dispositivo ni le coloque
calcomanías.
No utilice el dispositivo si la pantalla está
agrietada o rota.
Instale los dispositivos móviles y equipos con
precaución.
Evite que el producto caiga o este sujeto a un
fuerte impacto.
Asegure la máxima duración de la batería y el
cargador.
Evite cargar el dispositivo durante más de
una semana, ya que la sobrecarga puede
acortar la vida útil de la batería.
Con el tiempo, si el dispositivo no se utiliza,
se descargará y debe recargarse para
utilizarlo.
Desconecte el cargador de la fuente de
alimentación eléctrica cuando no se utilice.
Proteja su información personal y evite la
divulgación o el uso indebido de información
confidencial.
No distribuya material protegido por derechos
de autor o propiedad intelectual.
Malware y virus
Siga los siguientes consejos para proteger
su dispositivo contra malware y virus. De lo
contrario, podría causar daños o pérdida de
datos, que podrían no estar cubiertos por la
garantía.
No descargue aplicaciones de Fuentes
desconocidas.
No ingrese a sitios web poco confiables.
Elimine mensajes de texto SMS o
correos electrónicos de remitentes
desconocidos.
Configure una contraseña y cámbiela a
menudo.
Inhabilite las funciones inalámbricas
como Bluetooth® cuando no las utilice.
Correcta eliminación de este producto
La presencia de este símbolo en el producto,
en accesorios o en la literatura adjunta,
indica que el producto o sus accesorios
electrónicos (ej. Cargador, auricular, cable
USB) no deben desecharse junto con los
residuos domésticos.
Para prevenir posibles daños al
medioambiente o a la salud humana debido
a la eliminación descontrolada de residuos,
sepárelos de otro tipo de desechos y
recíclelos; ya que se promueve la
reutilización sostenible de recursos
materiales.
Los usuarios domésticos deben ponerse en
contacto ya sea con el proveedor del
producto o con las autoridades locales para
averiguar cómo y dónde pueden
depositarlos para un reciclaje
ambientalmente seguro.
Los usuarios comerciales deben contactar a
su proveedor y verificar las condiciones del
contrato de compra. Este producto y sus
accesorios electrónicos no deben mezclarse
con otros desechos comerciales.
Correcta eliminación de baterías en este
producto
La presencia de esta marca en la batería, en
el manual o en el embalaje indica que, una
vez finalizada la vida útil de las baterías, no
deben eliminarse junto con otros residuos
domésticos.
Los símbolos químicos Hg, Cd o Pb si están
presentes, indican que la batería contiene
Mercurio, Cadmio o Plomo por encima de
los valores de referencia permitidos en la
Normativa 2006/66 de la Unión Europea. Si
las baterías no se eliminan adecuadamente,
estas substancias pueden causar lesiones o
dañar el medio ambiente.
Para proteger los recursos naturales y
promover la reutilización de materiales,
separe las baterías de otros desperdicios y
recíclelas a través del sistema de
recolección gratuita en su localidad.
Tratamiento de
problemas comunes
1. Borrado de datos
Para borrar información y restablecer los datos
de fábrica, siga los siguientes pasos:
configuración – copia de seguridad – restablecer
datos de fábrica– aceptar.
2. No se oye la voz en el auricular
Verifique que el volumen no esté
completamente bajo.
Desenchufe los auriculares. Vuelva a enchufarlos
y asegúrese de empujar el conector hasta el
fondo.
3. Problemas de carga
Asegúrese de que la configuración del cargador
coincida con el dispositivo.
Intente cargar el dispositivo con otro cargador
compatible para verificar dónde puede estar la
falla.
4. Problema de descarga
Asegúrese de que conecta correctamente a
Internet. Ajuste la fecha y hora.
5. ¿Por qué algunos de los videos descargados
no se pueden reproducir normalmente?
El dispositivo es compatible con la mayoría de
formatos de archivo de vídeo, pero aún existen
diferencias con algunos formatos, modo
codificado, tasa de resolución y código, etc., lo
que podría causar que algunos de los videos
tengan problemas para reproducirse. Nuestra
sugerencia es que se utilice un software
adaptador de terceros, para transformarlo en la
PC y luego copiarlo al dispositivo.
6. El dispositivo se bloqueó o no enciende
Una vez que el dispositivo se cuelga durante su
funcionamiento, se puede reiniciar presionando
el botón RESET, ubicado en la parte posterior o
parte lateral del dispositivo.
NOTA:
La empresa no es responsable de ninguna
incompatibilidad de uso que pueda generarse
ocasionalmente entre aplicaciones desarrolladas
por terceros y este dispositivo.
En consecuencia, no se aceptarán devoluciones
de productos por este motivo.
Manufactured in China to Sky Devices Specifications
Google, Android, Google Play, YouTube and other marks
are trademarks of Google LLC.
1
FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired
operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
SAR Information Statement
Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed
the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications
Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish
permitted levels of RF energy for the general population. The guidelines are based on standards that were
developed by independent scientific organizations through periodic and thorough evaluation of scientific
studies. The standards include a substantial safety margin designed to assure the safety of all persons,
regardless of age and health. The exposure standard for wireless mobile phones employs a unit of
measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. *
Tests for SAR are conducted with the phone transmitting at its highest certified power level in all tested
frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level
of the phone while operating can be well below the maximum value. This is because the phone is designed
to operate at multiple power levels so as to use only the power required to reach the network. In general, the
closer you are to a wireless base station antenna, the lower the power output. Before a phone model is
available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit
established by the government adopted requirement for safe exposure. The tests are performed in positions
and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest
SAR value for this model phone when tested for use at the ear is 0.395W/Kg and when worn on the body, as
described in this user guide, is 0.561W/Kg(Body-worn measurements differ among phone models,
depending upon available accessories and FCC requirements). The maximum scaled SAR in hotspot mode is
0.561W/Kg. While there may be differences between the SAR levels of various phones and at various
positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment
Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC
RFexposure guidelines. SAR information on this model phone is on file with the FCC and can be found
under the Display Grant section of http://www.fcc.gov/ oet/fccid after searching on
FCC ID: 2ABOSSKYELITED55 Additional information on Specific Absorption Rates (SAR) can be
found on the Cellular Telecommunications Industry Asso-ciation (CTIA) web-site at
http://www.wow-com.com. * In the United States and Canada, the SAR limit for mobile phones used by the
public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a sub-stantial
margin of safety to give additional protection for the public and to account for any variations in
measurements.
2
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a
minimum separation distance of 10mm must be maintained between the user’s body and the handset,
including the antenna. Third-party belt-clips, holsters,
and similar accessories used by this device should not contain any metallic components. Body-worn
accessories that do not meet these requirements may not comply with RF exposure requirements and should
be avoided. Use only the supplied or an approved antenna.
GSM:
Operation Frequency range:
GSM 850:
824.20MHz-848.80MHz
PCS1900:
1850.20MHz-1909.80MHz
Modulation type:
2G
Voice(GMSK)
GPRS(GMSK)
EGPRS(GMSK, 8PSK)
Antenna type:
Internal Antenna
Antenna gain:
GSM 850:
-2.1 dBi(declare by Applicant)
PCS 1900:
-1.7 dBi(declare by Applicant)
WCDMA:
Operation Frequency range:
WCDMA Band V:
826.4MHz-846.6MHz
WCDMA Band II:
1852.4 MHz-1907.6 MHz
Modulation type:
3G
RMC(QPSK)
HSUPA(QPSK)
HSDPA(QPSK,16QAM)
Antenna type:
Internal Antenna
Antenna gain:
WCDMA Band V:
-2.1dBi(declare by Applicant)
WCDMA Band II:
-1.8 dBi(declare by Applicant)
LTE:
Operation Frequency range:
LTE Band 2:
TX: 1850MHz-1910MHz
RX: 1930MHz-1990MHz
LTE Band 4:
TX: 1710MHz-1755MHz
RX: 2110MHz-2155MHz
LTE Band 5:
TX: 824MHz-849MHz
RX: 869MHz-894MHz
LTE Band 12:
TX: 699MHz-716MHz
RX: 729MHz-746MHz
LTE Band 17:
TX: 704MHz-716MHz
RX: 734MHz-746MHz
LTE Band 66:
TX: 1710MHz-1780MHz
RX: 2110MHz-2200MHz
Modulation type:
QPSK
16QAM
64QAM
Antenna type:
Internal Antenna
Antenna gain:
LTE Band 2:
-1.66 dBi(declare by Applicant)
LTE Band 4:
-1.72 dBi(declare by Applicant)
LTE Band 5:
-1.9 dBi(declare by Applicant)
LTE Band 12:
-2.6 dBi(declare by Applicant)
3
LTE Band 17:
-2.7 dBi(declare by Applicant)
LTE Band 66:
-1.71 dBi(declare by Applicant)
BT:
Operation Frequency:
2402MHz~2480MHz
Transfer rate:
1/2/3 Mbits/s
Number of channel:
79
Modulation type:
GFSK, π/4-DQPSK, 8DPSK
Modulation technology:
FHSS
Antenna Type:
Internal Antenna
Antenna gain:
1.67dBi
BLE:
Operation Frequency:
2402-2480 MHz
Channel numbers:
40
Channel separation:
2 MHz
Modulation technology:
GFSK
Data speed :
1Mbps
Antenna Type:
Internal Antenna
Antenna gain:
1.67 dBi
2.4G WiFi:
Operation Frequency:
2412MHz~2462MHz:
802.11b/802.11g/802.11n(HT20)
2422MHz~2452MHz
802.11n(HT40)
Channel numbers:
11:
802.11b/802.11g/802.11(HT20)
7
802.11n(HT40)
Channel separation:
5MHz
Modulation technology:
(IEEE 802.11b)
Direct Sequence Spread Spectrum (DSSS)
Modulation technology:
(IEEE 802.11g/802.11n)
Orthogonal Frequency Division Multiplexing(OFDM)
Data speed (IEEE 802.11b):
1Mbps, 2Mbps, 5.5Mbps, 11Mbps
Data speed (IEEE 802.11g):
6Mbps, 9Mbps, 12Mbps, 18Mbps, 24Mbps, 36Mbps, 48Mbps, 54Mbps
Data speed (IEEE 802.11n):
Up to 150Mbps
Antenna Type:
Internal Antenna
Antenna gain:
1.67dBi
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
SKY DEVICES EliteD55 Manual de usuario
- Categoría
- Smartphones
- Tipo
- Manual de usuario
En otros idiomas
- English: SKY DEVICES EliteD55 User manual