Yamaha R-N602 El manual del propietario

Categoría
Receptores de medios de coche
Tipo
El manual del propietario
Printed in Malaysia ZS22690-1© 2015 Yamaha Corporation
Network Receiver
R-N602
OWNER’S MANUAL
MANUAL DE INSTRUCCIONES
RL
i En
English
English
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. For proper ventilation, allow the
following minimum clearances.
Top: 30 cm (11-3/4 in)
Rear: 20 cm (7-7/8 in)
Sides: 20 cm (7-7/8 in)
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign objects may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury. Yamaha
will not be held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power cord
disconnected from a wall outlet or the unit during a lightning
storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The
cabinet should never be opened for any reasons.
15
When not planning to use this unit for long periods of time (i.e.
vacation), disconnect the AC power plug from the wall outlet.
16 Be sure to read the “Troubleshooting” section in the owner’s
manual on common operating errors before concluding that
this unit is faulty.
17 Before moving this unit, press A downward to turn off this
unit and then disconnect the AC power plug from the AC wall
outlet.
18 Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the
outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may become
warm. Turn the system off, then leave this unit alone for
cooling.
20 Install this unit near the wall outlet and where the AC power
plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such as
sunshine, fire or the like. When you dispose of batteries,
follow your regional regulations.
22 Excessive sound pressure from earphones and headphones
can cause hearing loss.
23 VOLTAGE SELECTOR (General model only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
into the wall outlet.
Voltages are: AC 110-120/220-240 V, 50/60 Hz
This label is required to be attached to a product of which the
temperature of the top cover may be hot during operation.
Caution: Read this before operating your unit.
This unit is not disconnected from the AC power source as long as
it is connected to the wall outlet, even if this unit itself is turned off
by A. This state is called the standby mode. In this state, this unit is
designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
Do not use this unit within 22 cm (9 inches) of persons with a heart
pacemaker implant or defibrillator implant.
Caution: Read this before operating your unit.
ii En
Notes on remote controls and batteries
Do not spill water or other liquids on the remote control.
Do not drop the remote control.
Do not leave or store the remote control in the following
conditions:
places of high humidity, such as near a bath
places of high temperatures, such as near a heater or stove
places of extremely low temperatures
dusty places
Insert batteries according to the polarity markings (+ and -).
Change all batteries if you notice the operation range of the
remote control narrows.
If the batteries run out, immediately remove them from the
remote control to prevent an explosion or acid leak.
If you find leaking batteries, discard the batteries
immediately, taking care not to touch the leaked material. If
the leaked material comes into contact with your skin or gets
into your eyes or mouth, rinse it away immediately and
consult a doctor. Clean the battery compartment thoroughly
before installing new batteries.
Do not use old batteries together with new ones. This may
shorten the life of the new batteries or cause old batteries to
leak.
Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully
as these different types of batteries may have the same shape
and color.
Before inserting new batteries, wipe the battery compartment
clean.
Keep the batteries in a location out of reach of children.
Batteries can be dangerous if a child were to put in his or her
mouth.
If the batteries grow old, the effective operation range of the
remote control decreases considerably. If this happens,
replace the batteries with new one as soon as possible.
If you plan not to use the unit for a long period of time,
remove the batteries from the unit. Otherwise, the batteries
will wear out, possibly resulting in a leakage of battery liquid
that may damage the unit.
Do not throw away batteries with general house waste.
Dispose of them correctly in accordance with your local
regulations.
Bluetooth
Bluetooth is a technology for wireless communication between
devices within an area of about 10 meters (33 ft) employing the
2.4 GHz frequency band, a band which can be used without a
license.
Handling Bluetooth communications
The 2.4 GHz band used by Bluetooth compatible devices is a
radio band shared by many types of equipment. While
Bluetooth compatible devices use a technology minimizing the
influence of other components using the same radio band, such
influence may reduce the speed or distance of communications
and in some cases interrupt communications.
The speed of signal transfer and the distance at which
communication is possible differs according to the distance
between the communicating devices, the presence of obstacles,
radio wave conditions and the type of equipment.
Yamaha does not guarantee all wireless connections between
this unit and devices compatible with Bluetooth function.
1 En
PREPARATIONINTRODUCTION
BASIC
OPERATION
ADDITIONAL
INFORMATION
ADVANCED
OPERATION
English
INTRODUCTION
What you can do with this unit ................................. 2
Sources that can be played back on this unit ................. 2
Mastering useful apps (MusicCast CONTROLLER).... 3
Supplied accessories ................................................... 4
Controls and functions ............................................... 5
Front panel ..................................................................... 5
Front display .................................................................. 7
Rear panel ...................................................................... 8
Remote control............................................................... 9
PREPARATION
Connections............................................................... 11
Connecting the speakers .............................................. 12
Connecting the FM and AM antennas ......................... 13
Connecting the network cable ..................................... 14
Preparing a wireless antenna ....................................... 14
Connecting power cable .............................................. 15
Connecting to network ............................................. 16
Sharing the iOS device setting..................................... 17
Using the WPS push button configuration .................. 18
Set the wireless network connection manually............ 19
Connecting a mobile device to the unit directly
(Wireless Direct) ..................................................... 20
Verify the network connection status .......................... 21
BASIC OPERATION
Playback .................................................................... 22
Playing a source........................................................... 22
Using the sleep timer ................................................... 24
Listening to FM/AM radio....................................... 25
Setting the frequency steps .......................................... 25
FM/AM tuning............................................................. 25
Automatic preset tuning (FM stations only)................ 26
Manual tuning preset ................................................... 27
Recalling a preset station ............................................. 27
Clearing a preset station............................................... 28
Playing back music via Bluetooth............................ 29
Connecting a Bluetooth device (pairing) ..................... 29
Playing back Bluetooth device contents ...................... 29
Disconnecting a Bluetooth connection ........................ 30
Playing back music stored on media servers
(PCs/NAS) ............................................................. 31
Setting the media sharing of music files...................... 31
Playback of PC music contents.................................... 32
Listening to Internet radio....................................... 34
Registering favorite Internet radio stations
(bookmarks)............................................................. 35
Playing back iPod/iTunes music via a network
(AirPlay).................................................................36
Playback of iPod/iTunes music contents ..................... 36
Playing back music stored on a USB storage
device ......................................................................38
Connecting a USB storage device ............................... 38
Playback of USB storage device contents ................... 38
Playing back iPod music...........................................40
Connecting an iPod...................................................... 40
Playback of iPod content ............................................. 40
Switching information on the front display ............42
Registering the current playback song/station
(Preset function) ....................................................43
Registering to a preset ................................................. 43
Recalling a preset......................................................... 43
ADVANCED OPERATION
Configuring playback settings for different
playback sources (Option menu) .........................44
Option menu items....................................................... 44
Configuring various functions (Setup menu) .........45
Setup menu items......................................................... 45
Network ....................................................................... 46
Bluetooth ..................................................................... 47
Max Volume ................................................................ 48
Initial Volume.............................................................. 48
AutoPowerStdby (Auto Power Standby)..................... 48
ECO Mode ................................................................... 48
Configuring the system settings
(ADVANCED SETUP menu)...............................49
ADVANCED SETUP menu items .............................. 49
Changing the speaker impedance setting (SP IMP.) ... 49
Selecting the remote control ID (REMOTE ID).......... 49
Changing the FM/AM tuning frequency setting
(TU) ......................................................................... 49
Restoring the default settings (INIT)........................... 50
Updating the firmware (UPDATE) ............................. 50
Checking the firmware version (VERSION)............... 50
Updating the unit’s firmware via the network.......51
ADDITIONAL INFORMATION
Troubleshooting.........................................................52
Error indications on the front display.....................58
Trademarks ...............................................................59
Specifications .............................................................60
Index...........................................................................61
Contents
“Note” indicates precautions for use of the unit and its feature limitations. y indicates supplementary explanations for better use.
This manual explains operations using the supplied remote control.
This manual describes all the “iPod” and “iPhone” as the “iPod”. “iPod” refers to “iPod” and “iPhone”, unless otherwise specified.
In this manual, iOS and Android mobile devices are collectively referred to as “mobile devices”. The specific type of mobile
device is noted in explanations as needed.
2 En
INTRODUCTION
This unit is a network receiver compatible with a network source such as a media server and mobile device.
It supports playback from not only analog sources such as a CD player but also Bluetooth devices and network streaming
services.
*
You need a commercially available wireless router (access point) when you use a mobile device.
1 Play back the Internet radio (p. 34)
2 Play back the streaming service
(see the supplement for each service.)
3 Play back music files stored on your PC (p. 31)
4 Play back music files stored on your NAS
(p. 31)
5 Play back music files stored on your iPod/
iTunes with AirPlay (p. 36)
6 Play back audio content from Bluetooth
devices (p. 29)
7 Play back music files stored on your iPod
(p. 40)
8 Play back music files stored on your USB
device (p. 38)
9 Play back your external component (p. 11)
0 Listening to FM/AM radio (p. 25)
y
For details on connecting the external devices, see “Connections” (p. 11).
What you can do with this unit
Sources that can be played back on this unit
FM/AMFM/AM
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER
DISPLAY
SELECT
PHONES
SPEAKERS
AB
MODE
This unit
1 Internet
2 Streaming service
Modem
Router*
3 PC
5 AirPlay (iTunes)
4 NAS
7 iPod
0
5 AirPlay (iPod)
6 Bluetooth
8 USB
device
9 CD player etc.
Mobile
device
What you can do with this unit
3 En
INTRODUCTION
English
You can operate and program the unit, or play streaming services via this unit, by installing the free dedicated MusicCast
CONTROLLER app on a mobile device. For details, search for “MusicCast CONTROLLER” on the App Store or
Google Play.
MusicCast CONTROLLER capabilities
Basic operations of the unit (turn on/standby, adjust volume and select input)
Play songs stored on computers (servers)
Select an Internet radio station
Play music stored on mobile devices
Play music on streaming service
Distribute and receive audio between the unit and other Yamaha MusicCast supported devices
See MusicCast Setup Guide for details.
Mastering useful apps (MusicCast CONTROLLER)
4 En
Check that the following accessories are supplied with the product.
Supplied accessories
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
REPEAT
SHUFFLE
SLEEP
PHONO
B
A
SPEAKERS
OPTION
Remote control
FM antennaAM antenna
Batteries (x2)
(AA, R6, UM-3)
MusicCast Setup Guide
Controls and functions
5 En
INTRODUCTION
English
1 A (power)
Turns on/off (standby) the unit.
2 STANDBY/ON indicator
Lights up as follows:
Brightly lit: Power is on
Dimly lit: Standby mode
In standby mode, this unit consumes a small amount of power to
receive infrared signals from the remote control.
3 Remote control sensor
Receives infrared signals from the remote control.
4 DIMMER
Changes the brightness level of the front display. Choose
brightness from 5 levels by pressing this button
repeatedly.
5 DISPLAY
Selects the information displayed on the front display
(p. 42).
6 MODE
Sets the FM band reception mode to automatic stereo or
monaural (p. 26).
Switches the iPod operation modes (p. 41).
7 MEMORY
Registers the current FM/AM station as a preset when
TUNER is selected as the input source (p. 27).
Registers the current playback song or streaming station
as a preset when NET, USB (except iPod) are selected as
the input source (p. 43).
8 CLEAR
Clears a FM/AM preset station when TUNER is selected
as the input source (p. 28).
9 BAND
Switches between FM and AM (p. 25).
0 Front display
Shows information about the operational status of this
unit.
A PRESET j / i
Recalls a preset FM/AM station (p. 27) or song/streaming
station (p. 43).
B TUNING jj / ii
Selects the tuning frequency when TUNER is selected as
the input source (p. 25).
C PURE DIRECT and indicator
Allows you to listen to a source in the purest possible
sound (p. 22). The indicator above it lights up and the
front display turns off when this function is turned on.
Controls and functions
Front panel
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
12 3 4 5 6 7 8 9: B CA
Note
Controls and functions
6 En
D PHONES jack
Outputs audio to your headphones for private listening.
E SPEAKERS A/B
Turns on or off the speaker set connected to the
SPEAKERS A and/or SPEAKERS B terminals on the rear
panel each time the corresponding button is pressed.
F USB jack
For connecting a USB storage device (p. 38) or an iPod
(p. 40).
G INPUT selector
Selects the input source you want to listen to.
H BASS +/– control
Increases or decreases the low frequency response. The
center position produces a flat response (p. 23).
I TREBLE +/– control
Increases or decreases the high frequency response. The
center position produces a flat response (p. 23).
J BALANCE control
Adjusts the sound output balance of the left and right
speakers to compensate for sound imbalances caused by
speaker locations or listening room conditions (p. 23).
K LOUDNESS control
Retains a full tonal range at any volume level to
compensate for the human ears’ loss of sensitivity to high
and low-frequency ranges at a low volume level (p. 23).
L SELECT/ENTER (jog dial)
Turn the dial to select a numeric value or setting, and press
the dial to confirm.
M RETURN
Returns to the previous indication of the front display.
CONNECT
Use to control the unit using the dedicated MusicCast
CONTROLLER app for mobile devices. See MusicCast
Setup Guide for details.
N VOLUME control
Increases or decreases the sound output level.
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
NIHGED J KLMF
Controls and functions
7 En
INTRODUCTION
English
y
If the network connection is not set, turn the power ON to display “WAC” (Wireless Accessory Configuration) on the front panel and
trigger an automatic iOS device search. See “Sharing the iOS device setting” (p. 17) for details on the iOS device and network
connection.
1 Information display
Displays the current status (such as input name).
You can switch the information that is displayed when you
press DISPLAY on the front panel (p. 42).
2 STEREO
Lights up when the unit is receiving a stereo FM radio
signal.
3 TUNED
Lights up when the unit is receiving an FM/AM radio
station signal.
4 Signal strength indicator
Lights up when the unit connects to a wireless network or
operates as an access point. The strength of the wireless
network signal can be verified by the indicator status.
5 Bluetooth indicator
Lights up when the unit is connecting to a Bluetooth
device.
6 Speaker indicators
“A” lights up when the SPEAKERS A output is enabled
and “B” lights up when the SPEAKERS B output is
enabled.
7 SLEEP
Lights up when the sleep timer is on.
8 MUTE
Blinks when audio is muted.
9 Volume indicator
Indicates the current volume.
0 Cursor indicators
Indicate the remote control cursor keys currently
operational.
y
You can change the brightness level of the front display by
pressing DIMMER on the front panel (p. 5).
Front display
VOL.
MUTE
TUNEDSTEREO
A
SLEEP
B
1 9
6
: :
2
3 7 854
Controls and functions
8 En
1 PHONO jacks
For connecting to a turntable (p. 11).
2 OPTICAL 1/2 jacks
For connecting to audio components equipped with
optical digital output (p. 11).
3 ANTENNA terminals
For connecting to FM and AM antennas (p. 13).
4 COAXIAL 1/2 jacks
For connecting to audio components equipped with a
coaxial digital output (p. 11).
5 SPEAKERS terminals
Used to connect speakers (p. 12).
6 NETWORK jack
For connecting to a network with a network cable (p. 14).
7 Wireless antenna
For connecting to a network device wirelessly (p. 14).
8 Power cable
For connecting to an AC wall outlet (p. 15).
9 LINE 1-3 jacks
For connecting to analog audio components (
p. 11
).
0 CD jacks
For connecting to a CD player (p. 11).
A SUBWOOFER PRE OUT jack
For connecting to a subwoofer with built-in amplifier
(p. 11).
B VOLTAGE SELECTOR switch
(General model only)
Selects the switch position according to your local voltage
(p. 15).
Rear panel
A
B
SPEAKERS
NETWORK
COAXIAL
OPTICAL
FM AM
75Ω
ANTENNA
SUBWOOFER
PRE OUT
PHONO
IN
1
IN
OUT
2
1
2
1
2
IN
CD
LINE
OUT
3
VO LTAGE SELECTOR
220-240V
110-120V
SIGNAL
GND
3 5 68
A
B
1 2 4 7
9 :
(General model)
Controls and functions
9 En
INTRODUCTION
English
1 Infrared signal transmitter
Sends infrared signals.
2 SPEAKERS A/B
Turns on and off the set of speakers connected to the SPEAKERS
A and/or SPEAKERS B terminals on the rear panel of this unit
when the corresponding key is pressed.
3 Input selection keys
Select an input source for playback.
PHONO PHONO jacks
COAX 1/2 COAXIAL1/2 jacks
BLUETOOTH Bluetooth connection
OPT 1/2 OPTICAL 1/2 jacks
CD CD jacks
LINE 1-3 LINE 1-3 jacks
TUNER FM/AM tuner
NET Network source (press repeatedly to select a
desired network source)
USB USB jack (on the front panel)
4 Radio keys
Operate the FM/AM radio (p. 25).
BAND Switches between FM and AM.
TUNING jj/ii Selects the radio frequency.
5 Preset keys
MEMORY Registers the current FM/AM station as a
preset when TUNER is selected as the input
source (p. 27).
Registers the current playback song or
streaming station as a preset when NET, USB
(except iPod) are selected as the input source
(p. 43).
PRESET j/i Recalls a preset FM/AM station (p. 27) or
song/streaming station (p. 43).
6 Menu operation keys
Cursor keys Select a menu or a parameter.
(B/C/D/E)
ENTER Confirms a selected item.
RETURN Returns to the previous state.
7 HOME
Moves up top level when selecting music files, folders, etc.
8 SETUP
Displays the “Setup” menu (p. 45).
9 NOW PLAYING
Displays music information when selecting music files, folders,
etc.
0 VOLUME +/-
Adjust the volume.
A Playback keys
Let you play back and perform other operations for network
sources, Bluetooth devices and USB devices.
Remote control
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
REPEAT
SHUFFLE
SLEEP
PHONO
B
A
SPEAKERS
OPTION
1
3
6
7
0
8
9
2
4
5
A
Controls and functions
10 En
B A (power)
Turns on/off (standby) the unit.
C SLEEP
Sets the sleep timer (p. 24).
D OPTION
Displays the “Option” menu (p. 44).
E MUTE
Mutes the audio output.
Installing batteries
Change all batteries if the operation range of the remote control
narrows.
Before inserting new batteries, wipe the compartment clean.
Operation range
The remote controls transmit a directional infrared beam.
Be sure to aim the remote controls directly at the remote
control sensor on the front panel of this unit.
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
REPEAT
SHUFFLE
SLEEP
PHONO
B
A
SPEAKERS
OPTION
B
C
D
E
Notes
2
13
11 En
PREPARATION
English
PREPARATION
Do not connect this unit or other components to the main power until all connections between components are complete.
All connections must be correct: L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty,
no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be
unnatural and lack bass. Refer to the owners manual for each of your components.
Do not let bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the speakers.
Make sure to use RCA cables, optical cables to connect audio components.
y
The PHONO jacks are designed for connecting a turntable with an MM cartridge.
Connect your turntable to the GND terminal to reduce noise in the signal. However, for some turntables, you may hear less noise
without the GND connection.
In order to prevent the audio signal from looping when an audio recording device is connected, the audio signal is not output from the
LINE 2 (OUT) jacks when LINE 2 is selected. Similarly, the audio signal is not output from the LINE 3 (OUT) jacks when LINE 3 is
selected.
Connections
CAUTION
Only PCM signals can be input to the digital (OPTICAL/COAXIAL) jacks of this unit.
Note
A
B
SPEAKERS
NETWORK
COAXIAL
OPTICAL
FM AM
75Ω
ANTENNA
SUBWOOFER
PRE OUT
PHONO
IN
1
IN
OUT
2
1
2
1
2
IN
CD
LINE
OUT
3
SIGNAL
GND
O C
Audio
input
Audio
output
Speakers B
Turntable
Audio
output
DVD player, etc.
GND
Audio output
(digital coaxial)
Audio output
(digital optical)
CD player, etc.
Audio
output
CD player
Subwoofer
CD recorder, etc.
Speakers A
12 En
Connections
Connecting speaker cables
Speaker cables have two wires. One is for connecting the
negative (–) terminal of the unit and the speaker, and the
other is for the positive (+) terminal. If the wires are
colored to prevent confusion, connect the black wire to the
negative and the other wire to the positive terminal.
a
Remove approximately 10 mm (3/8”) of insulation from the ends of
the speaker cable and twist the bare wires of the cable firmly together.
b Loosen the speaker terminal.
c Insert the bare wires of the cable into the gap on the side (upper
right or bottom left) of the terminal.
d Tighten the terminal.
Connecting via banana plug
(General model only)
Tighten the knob and then insert the banana plug into the
end of the corresponding terminal.
Bi-wire connection
Bi-wire connection separates the woofer from the
combined midrange and tweeter section. A bi-wire
compatible speaker has four binding post terminals. These
two sets of terminals allow the speaker to be split into two
independent sections. With these connections, the mid and
high frequency drivers are connected to one set of terminals
and the low frequency driver to another set of terminals.
Connect the other speaker to the other set of terminals in
the same way.
When making bi-wire connections, remove the shorting bridges
or cables on the speaker. Refer to the speakers’ instruction
manuals for more information.
y
To use the bi-wire connections, press SPEAKERS A and
SPEAKERS B on the front panel or on the remote control so that
both speaker indicators (“A” and “B”) light up on the front
display.
Connecting the speakers
aa
b
b
d
d
c
c
Note
A
B
SPEAK
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
SLEEP
PHONO
B
A
SPEAKERS
13 En
Connections
PREPARATION
English
The antennas for receiving FM and AM broadcasts are included with this unit. In general, these antennas should provide
sufficient signal strength. Connect each antenna correctly to the designated terminals.
If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center
about outdoor antennas.
Assembling the supplied AM antenna Connecting the wires of the AM antenna
Connecting the FM and AM antennas
Note
COAXIAL
OPTICAL
FM AM
75Ω
ANTENNA
SUBWOOFER
PRE OUT
PHONO
IN
1
IN
OUT
2
1
2
1
2
IN
CD
LINE
OUT
3
SIGNAL
GND
FM antenna
(included)
Outdoor AM antenna
Use 5 to 10 m of vinyl-covered wire extended
outdoors from a window.
Outdoor
FM antenna
The AM antenna should always be connected, even if an outdoor
AM antenna is connected to this unit.
The AM antenna should be placed away from this unit.
AM antenna (included)
or
14 En
Connections
Connect the unit to your router with a commercially-available STP network cable (CAT-5 or higher straight cable).
If you connect the unit wirelessly, erect the wireless
antenna. For information on how to connect the unit to a
wireless network, see “Connecting to network” (p. 16).
Do not apply excessive force on the wireless antenna. Doing so
may damage the antenna.
Connecting the network cable
A
B
SPEAKERS
NETWORK
COAXIAL
OPTICAL
FM AM
75Ω
ANTENNA
SUBWOOFER
PRE OUT
PHONO
IN
1
IN
OUT
2
1
2
1
2
IN
CD
LINE
OUT
3
VOLTA GE SELECTOR
220-240V
110-120V
SIGNAL
GND
LAN
WAN
Network Attached Storage
(NAS)
Internet
Modem
Router
Network cable
PC
This unit (rear)
Mobile device
(such as iPhone)
(General model)
Preparing a wireless antenna
Note
WIRELES
S
WORK
15 En
Connections
PREPARATION
English
After all the connections are complete, plug in the power
cable.
Connecting power cable
Before connecting the power cable
(General model only)
Set the switch position of VOLTAGE SELECTOR
according to your local voltage. Voltages are AC 110–
120/220–240 V, 50/60 Hz.
Make sure you set VOLTAGE SELECTOR of the unit
BEFORE plugging the power cable into an AC wall outlet.
Improper setting of VOLTAGE SELECTOR may cause
damage to the unit and create a potential fire hazard.
Note
VOLTA GE SELECTOR
220-240V
110-120V
The unit (rear)
VOLTAGE SELECTOR
VOLTA GE SELECTOR
220-240V
110-120V
16 En
There are several methods to connect the unit to a network. Select a connection method according to your environment.
Some security software installed on your PC or the firewall settings of network devices (such as a router) may block the access of the
unit to the network devices or the Internet. In these cases, configure the security software or firewall settings appropriately.
Each server must be connected to the same subnet as the unit.
To use the service via the Internet, broadband connection is strongly recommended.
Connecting with the MusicCast CONTROLLER app
See MusicCast Setup Guide for details.
Connecting with the wired router
Connecting with a wireless router (access point)
Connect to the network with the method listed below that corresponds to your environment.
Connecting without a wired router or wireless router (access point)
When the unit is connected to the network with Wireless Direct, it cannot connect to any other wireless router (access point). To play
back contents from the Internet, connect this unit to a network with a wired router or wireless router (access point).
Connecting to network
Notes
When playing a high-resolution audio source via the network, we recommend connecting with a wired router for stable playback.
Note
Connecting using the DHCP server function of the
router
You can connect to the network by
simply making a wired connection
(p. 14)
Connecting using the Wi-Fi setting of the iOS
device (iPhone / iPod touch)
Share the Wi-Fi setting of the iOS
device (p. 17)
Connecting using WPS push button configuration
on the wireless router (or access point)
Use the WPS push button
configuration (p. 18)
Connecting with a wireless router (access point)
without WPS push button configuration
Set the network connection
manually (p. 19)
Connecting wirelessly to a mobile device
(Wireless Direct)
Connect wirelessly with Wireless
Direct (p. 20)
17 En
Connecting to network
PREPARATION
English
You can easily setup a wireless connection by applying the
connection settings on iOS devices (iPhone/iPod touch).
Before proceeding, confirm that your iOS device is
connected to a wireless router (access point).
1 Press A to turn on this unit.
2 Press SETUP.
3 Use the cursor keys (B / C) to select
“Network” and press ENTER.
y
To return to the previous state, press RETURN.
4 Use the cursor keys (B / C) to select
“Connection” and press ENTER.
5 Use the cursor keys (B / C) to select
“Wireless” and press ENTER.
6 Use the cursor keys (B / C) to select “Share
Setting” and press ENTER.
7 Use the cursor keys (B / C) to select the
desired connection method and press
ENTER.
The following connection methods are available.
When you select “Wireless (WAC) as the connection method, all
network settings are initialized.
Sharing the iOS device setting wirelessly
If you select “Wireless (WAC)” as the connection method,
perform the network setting sharing operation on your iOS
device. (The following procedure is a setup example for
iOS 8.)
1 On the iOS device, select the unit as the
AirPlay speaker in the Wi-Fi screen.
2 Check the network currently selected and tap
“Next”.
When the sharing process finishes, the unit is
automatically connected to the selected network
(access point).
When the setting finishes, verify whether the unit is
connected to a wireless network (p. 21).
Sharing the iOS device setting
If the network connection is not set, when you turn on
this unit, “WAC” (Wireless Accessory Configuration)
appears on the front display, and the iOS device setting
can be shared.
To share the iOS device setting, perform the network
setting sharing operation on your iOS device.
R-N602 XXXXXX
WAC
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
WPS
WIRELESS
Wireless(WAC)
SHARE
Wireless
(WAC)
You can apply the connection settings on the iOS
device to the unit using a wireless connection. For
details, see “Sharing the iOS device setting
wirelessly”. (You need iOS device with iOS 7 or
later.)
USB
Cable
You can apply the connection settings on the iOS
device to the unit using a USB cable. For details, see
“Sharing the iOS device setting using a USB cable”.
(You need iOS device with iOS 5 or later.)
Note
18 En
Connecting to network
Sharing the iOS device setting using a
USB cable
If you select “USB Cable” as the connection method,
follow the procedure below to share the iOS device setting
with the unit.
1 Connect the iOS device to the USB jack, and
disable the screen lock on the iOS device.
2 Press ENTER.
3 Tap “Allow” in the message appeared on the
iOS device.
When the connection process finishes, “Completed”
appears on the front display.
When the setting finishes, verify whether the unit is
connected to a wireless network (p. 21).
4 To exit from the menu, press SETUP.
You can easily set up a wireless connection with one push
of the WPS button.
This configuration does not work if the security method of your
wireless router (access point) is WEP. In this case, use other
connection method.
1 Press A to turn on this unit.
2 Press SETUP.
3 Use the cursor keys (B / C) to select
“Network” and press ENTER.
y
To return to the previous state, press RETURN.
4 Use the cursor keys (B / C) to select
“Connection” and press ENTER.
5 Use the cursor keys (B / C) to select
“Wireless” and press ENTER.
6 Press ENTER twice.
“Connecting” appears on the front display.
7 Push the WPS button on the wireless router
(access point).
When the connection process finishes, “Completed”
appears on the front display. When the setting
finishes, verify whether the unit is connected to a
wireless network (p. 21).
If “Not connected” appears, repeat from Step 1 or try
another connection method.
8 To exit from the menu, press SETUP.
Using the WPS push button
configuration
Note
MEMORY CLEAR
BASSINPUT
5V
1A
TREBLE
DIMMER MODE
DISPLAY
PHONES
SPEAKERS
AB
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
About WPS
WPS (Wi-Fi Protected Setup) is a standard established by the
Wi-Fi Alliance, which allows easy establishment of a
wireless home network.
WPS
WIRELESS
19 En
Connecting to network
PREPARATION
English
Before performing the following procedure, check the
security method and security key on the wireless router
(access point).
1 Press A to turn on this unit.
2 Press SETUP.
3 Use the cursor keys (B / C) to select
“Network ” and press ENTER.
y
To return to the previous state, press RETURN.
4 Use the cursor keys (B / C) to select
“Connection” and press ENTER.
5 Use the cursor keys (B / C) to select
“Wireless” and press ENTER.
6 Use the cursor keys (B / C) to select “Manual
Setting” and press ENTER.
7 Use the cursor keys (B / C) to select “SSID”
and press ENTER.
8 Use the cursor keys to enter the SSID on the
wireless router (access point), and press
RETURN to previous state.
Use the cursor keys (D/E) to move the edit position
and the cursor keys (B/C) to select a character.
9 Use the cursor keys (B / C) to select
“Security” and press ENTER.
10 Use the cursor keys (D / E) to select desired
security method and press RETURN.
Settings
None, WEP, WPA2-PSK (AES), Mixed Mode
If you select “None”, the connection may be insecure since the
communication is not encrypted.
11 Use the cursor keys (B / C) to select
“Security Key” and press ENTER.
12 Use the cursor keys to enter the security key
on the wireless router (access point), and
press RETURN to previous state.
If you select “WEP” in step 10, enter either 5 to 13
character string or 10 to 26 hexadecimal digits.
If you select “WPA2-PSK (AES)” or “Mixed Mode”
in step 10, enter either 8 to 63 character string or 64
hexadecimal digits.
Use the cursor keys (D/E) to move the edit position
and the cursor keys (B/C) to select a character.
You can insert / delete a character, by pressing
PRESET i (insert) or PRESET j (delete).
13 Use the cursor keys (B / C) to select
“Connect[ENTER]” and press ENTER to save
the setting.
If “ERROR” appears, check the SSID and security
key on the wireless router (access point) and repeat
from Step 7.
If “ERROR” not appears, a connection is success.
Verify whether the unit is connected to a wireless
network (p. 21).
14 To exit from the menu, press SETUP.
Set the wireless network
connection manually
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
SSID
MANUAL
SSID
Note
WPA2-PSK(AES)
SECURITY
KEY
20 En
Connecting to network
Using Wireless Direct, this unit can operate as a wireless
network access point that mobile devices can directly
connect to.
When the unit is connected to the network with Wireless Direct, it
cannot connect to any other wireless router (access point). To
play back contents from the Internet, connect this unit to a
network with a wired router or wireless router (access point).
1 Press A to turn on this unit.
2 Press SETUP.
3 Use the cursor keys (B / C) to select
“Network” and press ENTER.
y
To return to the previous state, press RETURN.
4 Use the cursor keys (B / C) to select
“Connection” and press ENTER.
5 Use the cursor keys (B / C) to select
“WirelesDirect” and press ENTER.
6 Press ENTER to check the SSID on this unit,
and press RETURN to previous state.
7 Use the cursor keys (B / C) to select
“Security” and press ENTER.
8 Use the cursor keys (D / E) to select desired
security method and press RETURN.
Settings
None, WPA2-PSK (AES)
If you select “None”, the connection may be insecure since the
communication is not encrypted.
9 Use the cursor keys (B / C) to select
“Security Key” and press ENTER.
10 Use the cursor keys to enter the security key
on this unit, and press RETURN to previous
state.
Enter either 8 to 63 character string or 64
hexadecimal digits.
Use the cursor keys (D / E) to move the edit position
and the cursor keys (B / C) to select a character.
You can insert / delete a character, by pressing
PRESET i (insert) or PRESET j (delete).
11 Use the cursor keys (B / C) to select
“Connect[Enter]” and press ENTER to save
the setting.
The SSID and security key information is required
for setup of a mobile device.
When you select the “SSID” in step 6, you can check
the configured SSID on this unit. The SSID of this
unit can be change by using cursor keys (B / C / D /
E).
12 Configure the Wi-Fi settings of a mobile
device.
For details on settings of your mobile device, refer to
the instruction manual of the mobile device.
(1) Enable the Wi-Fi function on the mobile device.
(2) Select the SSID of this unit from the list of
available access points.
(3) When you are prompted for a password, enter the
security key displayed in Step 10.
If “ERROR” appears, check the security key on this
unit and repeat Step 12.
If “ERROR” not appears, a connection is success.
Verify whether the unit is connected to a wireless
network (p. 21).
13 To exit from the menu, press SETUP.
Connecting a mobile device to the
unit directly (Wireless Direct)
Note
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
SSID
W DIRECT
WPA2-PSK(AES)
W DIRECT
Note
KEY
21 En
Connecting to network
PREPARATION
English
Perform the following procedure to verify the unit’s
connection to a network.
1 Press SETUP.
2 Use the cursor keys (B / C) to select
“Network” and press ENTER.
y
To return to the previous state, press RETURN.
3 Use the cursor keys (B / C) to select
“Information” and press ENTER.
4 Use the cursor keys (B / C) to select
“STATUS”.
When “Connect” appears, the unit is connected to a
network. If “Disconnect” appears, reset connection.
5 To exit from the menu, press SETUP.
Verify the network connection
status
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
Connect
STATUS
22 En
BASIC OPERATION
1 Press A (power) to turn on this unit.
2 Rotate the INPUT selector on the front panel
(or press one of the input selection keys on
the remote control) to select the input source
you want to listen to.
3 Press SPEAKERS A and/or SPEAKERS B on
the front panel or on the remote control to
select speakers A and/or speakers B.
When speaker set A or speaker set B are turned on,
“A” or “B” is displayed on the front display
accordingly (p. 7).
When one set of speakers is connected using bi-wire connections,
or when using two sets of speakers simultaneously (A and B),
make sure “A” and “B” are displayed on the front display.
When listening with headphones, turn off the speakers.
4 Play the source.
5 Rotate the VOLUME control on the front
panel (or press VOLUME +/– on the remote
control) to adjust the sound output level.
y
You can adjust the tonal quality by using the BASS, TREBLE,
BALANCE and LOUDNESS controls or the PURE DIRECT
switch on the front panel.
6 When you finish using, press A (Power) on
the front panel to turn off the power.
When you press A (Power) on the remote control,
this unit set to standby mode.
Enjoying pure high fidelity sound
(Pure Direct)
When the PURE DIRECT switch is turned on, routes
input signals from your audio sources so that the input
signals bypass the BASS, TREBLE, BALANCE and
LOUDNESS controls, thus eliminating any alterations to
the audio signals and creating the purest possible sound.
The PURE DIRECT indicator lights up and the front
display turns off after a few seconds.
When the PURE DIRECT switch is turned on, the front display
turns off.
The BASS, TREBLE, BALANCE, and LOUDNESS controls do
not function while the PURE DIRECT switch is turned on.
Playback
Playing a source
Notes
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
TUNING
BAND
SLEEP
PHONO
B
A
SPEAKERS
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
OPTION
Notes
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
23 En
Playback
BASIC
OPERATION
English
Adjusting the BASS and TREBLE
controls
The BASS and TREBLE controls adjust high and low
frequency response.
The center position produces a flat response.
BASS control
When you feel there is not enough bass (low frequency
sound), rotate clockwise to boost. When you feel there is
too much bass, rotate counterclockwise to suppress.
Control range: –10 dB to +10 dB (20 Hz)
TREBLE control
When you feel there is not enough treble (high frequency
sound), rotate clockwise to boost. When you feel there is
too much treble, rotate counterclockwise to suppress.
Control range: –10 dB to +10 dB (20 kHz)
Adjusting the BALANCE control
The BALANCE control adjusts the sound output balance
of the left and right speakers to compensate for sound
imbalance caused by speaker locations or listening room
conditions.
Adjusting the LOUDNESS control
Retain a full tonal range at any volume level, thus
compensating for the human ears’ loss of sensitivity to
high and low-frequency ranges at low volume.
If the PURE DIRECT switch is turned on with the
LOUDNESS control set at a certain level, the input signals
bypass the LOUDNESS control, resulting in a sudden
increase in the sound output level. To prevent your ears or
the speakers from being damaged, be sure to press the
PURE DIRECT switch after lowering the sound output
level or after checking that the LOUDNESS control is
properly set.
1 Set the LOUDNESS control to the FLAT
position.
2 Rotate the VOLUME control on the front
panel (or press VOLUME +/– on the remote
control) to set the sound output level to the
loudest listening level that you would listen
to.
3 Rotate the LOUDNESS control until the
desired volume is obtained.
y
After setting the LOUDNESS control, enjoy listening to music at
your preferred volume level. If the effect of the LOUDNESS
control setting is too strong or weak, readjust the LOUDNESS
control.
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
CAUTION
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
OPTION
24 En
Playback
Use this feature to automatically set this unit to standby
mode after a certain amount of time. The sleep timer is
useful when you are going to sleep while this unit is
playing or recording a source.
The sleep timer can only be set with the remote control.
1 Press SLEEP repeatedly to set the amount of
time before this unit is set to standby mode.
Each time you press SLEEP, the front display
changes as shown below.
The SLEEP indicator blinks while setting the amount
of time for the sleep timer.
If the sleep timer is set, the SLEEP indicator on the
front display lights up.
y
To disable the sleep timer, select “Sleep Off”.
The sleep timer setting can also be canceled by pressing
A (power) to set this unit to standby mode.
Using the sleep timer
Note
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
LINE 2 LINE 3
SLEEP
PHONO
B
A
SPEAKERS
A
SLEEP
VOL.
A
Sleep 120min.
SLEEP
25 En
BASIC
OPERATION
English
At the factory, the frequency step setting is set to 50 kHz
for FM and 9 kHz for AM. Depending on your country or
region, set the frequency steps to 100 kHz for FM and 10
kHz for AM.
1 Turn off the unit.
2 When holding down RETURN on the front
panel, press A (power).
3 Rotate SELECT/ENTER to select “TU”.
4 Press SELECT/ENTER to select
“FM100/AM10”.
5 Press A (power) to set the unit to turn off and
turn it on again.
1 Press TUNER to select “TUNER” as the input
source.
2 Press BAND repeatedly to select the
reception band (FM or AM).
3 Press and hold TUNING jj / ii for more than
1 second to begin tuning.
Press ii to tune in to a higher frequency.
Press jj to tune in to a lower frequency.
The frequency of the received station is shown in the
front display.
If a broadcast is being received, “TUNED” indicator
on the front display will be lit. If a stereo broadcast is
being received, the “STEREO” indicator will also lit.
y
If the station signals are weak, tuning search does not stop at the
desired station.
When the signal reception for an FM radio station is unstable,
switching to monaural may improve it.
Listening to FM/AM radio
Setting the frequency steps
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
TU••••FM50/AM9
FM/AM tuning
TUNING jj / ii
TUNER
BAND
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SLEEP
PHONO
B
A
SPEAKERS
VOL.
TUNEDSTEREO
A
FM 98.50MHz
26 En
Listening to FM/AM radio
Improving FM reception (FM mode)
If the signal from the station is weak and the sound quality
is not good, set the FM band reception mode to monaural
mode to improve reception.
1 Press MODE repeatedly to select “Stereo”
(automatic stereo mode) or “Mono”
(monaural mode) when this unit is tuned in to
an FM radio station.
When Mono is selected, FM broadcasts will be heard
in monaural sound.
The STEREO indicator on the front panel lights up while
listening to a station in stereo mode.
You can use the automatic preset tuning function to
automatically register FM stations as presets. This
function enables this unit to automatically tune in to FM
stations that have a strong signal and register up to 40 of
those stations in order. You can then easily recall any
preset station by selecting its preset number.
If a station is registered to a preset number that already has a
station registered to it, the previously registered station is
overwritten.
If the station you want to register is weak in signal strength, try
using the manual preset tuning method.
y
FM stations registered as presets using the automatic preset
registration feature will be heard in stereo.
1 Press TUNER to select “TUNER” as the input
source.
2 Press OPTION on the remote control.
The “Option” menu is displayed (p. 44).
3 Press B / C to select “Auto Preset”, and then
press ENTER.
This unit starts scanning the FM band about 5
seconds later from the lowest frequency upwards.
To begin scanning immediately, hold down ENTER.
y
Before scanning begins, you can specify the first preset number
to be used by pressing PRESET j / i or cursor key (B/C) on the
remote control.
To cancel scanning, press BAND or RETURN.
When scanning is complete, “FINISH” is displayed and
then the display returns to original state.
Note
Automatic preset tuning
(FM stations only)
Notes
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
LINE 1
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
PRESET j / i
RETURN
OPTION
TUNER
BAND
ENTER
VOL.
A
Auto Preset
OPTION
VOL.
A
01:FM 87.50MHz
READY
27 En
Listening to FM/AM radio
BASIC
OPERATION
English
Select a radio station manually and register it to a preset
number. You can then easily recall any preset station by
selecting its preset number.
1 Follow “FM/AM tuning” (p.25) to tune into the
desired radio station.
2
Hold down MEMORY for more than 2 seconds.
The first time that you do register a station, the selected
radio station will be registered to the preset number
“01”. Thereafter, each radio station you select will be
registered to the next empty (unused) preset number
after the most recently registered number.
y
To select a preset number for registering, press MEMORY once
after tuning into the desired radio station, press PRESET j / i to
select a preset number, and then press MEMORY again.
You can recall preset stations that were registered using
automatic station preset or manual station preset.
1 Press TUNER to select “TUNER” as the input
source.
2 Press PRESET j / i to select a preset
number.
y
Preset numbers to which no stations are registered are skipped.
“No Presets” is displayed if no stations are registered.
Manual tuning preset
NET USB
TUNER
PRESET
TUNING
BAND
MEMORY
ENTER
PRESET j / i
MEMORY
VOL.
A
01:FM 98.50MHz
MEMORY
TUNEDSTEREO
VOL.
A
02:Empty
9850
TUNEDSTEREO
Recalling a preset station
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SLEEP
PHONO
B
A
SPEAKERS
TUNER
PRESET j / i
28 En
Listening to FM/AM radio
Clear radio stations registered to the preset numbers.
1 Press TUNER to select “TUNER” as the input
source.
2 Press OPTION.
3 Use the cursor keys to select “Clear Preset”
and press ENTER.
4 Use the cursor keys (B / C) to select a preset
station to be cleared and press ENTER.
If the preset station is cleared, “Cleared” appears and
then the next in-use preset number is displayed.
5 Repeat step 4 until all desired preset stations
are cleared.
6 To exit from the “Option” menu, press
OPTION.
y
You can clear a preset station from the front panel.
(1) Press CLEAR on the front panel.
(2) Press PRESET D/E to select the preset station that you want
to clear.
(3) Press SELECT/ENTER or CLEAR to clear the preset station.
Clearing a preset station
LINE 1
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
OPTION
ENTER
TUNER
VOL.
Clear Preset
OPTION
VOL.
A
01:FM 98.50MHz
CLEAR
TUNEDSTEREO
VOL.
01:Cleard
CLEAR
A
29 En
BASIC
OPERATION
English
You can play back music files stored on a Bluetooth
device (such as mobile device) on the unit.
Please also refer to the owner’s manual of your Bluetooth
device.
To use the Bluetooth function, set “Bluetooth” (p. 47) in the
“Setup” menu to “On”.
•A Bluetooth device may not be detected by the unit or some
feature may not be compatible, depending on the model.
y
You can transmit audio to Bluetooth speakers or headphones
using the MusicCast CONTROLLER app. To transmit audio, set
“Audio Send” (p. 47) in the “Setup” menu to “On”. The audio
output can only be selected from the MusicCast CONTROLLER
app.
When connecting a Bluetooth device to the unit for the
first time, the pairing operation is required to perform.
Pairing is an operation that registers the Bluetooth devices
with each other beforehand. Once pairing has been
completed, subsequent reconnection will be easy even
after the Bluetooth connection is disconnected.
1 Press BLUETOOTH to select “Bluetooth” as
the input source.
If another Bluetooth device is already connected,
disconnect the Bluetooth connection before you
perform a pairing operation.
2 Turn on the Bluetooth function of the
Bluetooth device.
3 On the Bluetooth device, select the unit’s
model name from the available device list.
After pairing has been completed and the unit is
connected to the Bluetooth device, “Connected”
appears on the front display, and Bluetooth indicator
will be light up.
y
If the pass key is required, enter the number “0000”.
Complete a pairing procedure within 5 minutes.
If no Bluetooth devices are found, “Not found” appears.
Connect a paired Bluetooth device and start playback.
Check the following beforehand:
Pairing has been completed.
Bluetooth function on the Bluetooth device is turned on.
1 Press BLUETOOTH to select “Bluetooth” as
the input source.
y
If the unit detects the Bluetooth device previously connected, the
unit automatically connects to the Bluetooth device after Step 1.
To establish another Bluetooth connection, first disconnect the
current Bluetooth connection.
Playing back music via Bluetooth
Notes
Connecting a Bluetooth device
(pairing)
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
SLEEP
PHONO
B
A
SPEAKERS
Playing back Bluetooth device
contents
Connected
BLUETOOTH
A
VOL.
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
SLEEP
PHONO
B
A
SPEAKERS
REPEAT
SHUFFLE
30 En
Playing back music via Bluetooth
2 Operate the Bluetooth device to establish a
Bluetooth connection.
Select the unit’s model name from the Bluetooth
device list on your device.
When a connection is established, Bluetooth indicator
on the front display will be light up.
y
If you cannot connect the Bluetooth device, please perform
pairing again.
3 Operate the Bluetooth device to play back
music.
y
You can use the playback keys on the remote control to control
playback.
Follow one of the procedures below to disconnect a
Bluetooth connection.
Turn off the Bluetooth function on the Bluetooth
device.
Hold down BLUETOOTH on the remote control for at
least 3 seconds.
Select “Disconnect” in “Audio Receive” (p. 47) in the
“Setup” menu, and then press ENTER.
Select an input source other than “Bluetooth” on the
unit.
Disconnecting a Bluetooth
connection
31 En
BASIC
OPERATION
English
You can play back music files stored on your PC or DLNA-compatible NAS on the unit.
To use this function, the unit and your PC/NAS must be connected to the same router (p. 14). You can check whether the network
parameters (such as the IP address) are properly assigned to the unit in “Information” (p.46) in the “Setup” menu.
The unit supports playback of WAV (PCM format only), AIFF, MP3, WMA, MPEG-4 AAC, FLAC, ALAC and DSD files.
The unit is compatible with sampling rates of up to 192 kHz for WAV, AIFF and FLAC files, 96 kHz for ALAC files, and 48 kHz for
other files.
The unit is compatible with 2.8 MHz/5.6 MHz (1 bit) DSD files.
Digital Rights Management (DRM) contents cannot be played back.
To play back music files, the server software installed on the computer (server) must support the music files that you want to play
back.
y
You can connect up to 16 media servers to this unit.
To play back music files in your computer with this unit,
you need to make the media sharing setting between the
unit and computer (Windows Media Player 11 or later). In
here, setting with Windows Media Player in Windows 7 is
taken as an example.
When using Windows Media Player 12
1 Start Windows Media Player 12 on your PC.
2 Select “Stream”, then “Turn on media
streaming.
The control panel window of your PC appears.
3 Click “Turn on media streaming.
Playing back music stored on media servers (PCs/NAS)
Notes
PC
NAS
This unit
Setting the media sharing of music
files
32 En
Playing back music stored on media servers (PCs/NAS)
4 Select “Allowed” from the drop-down list
next to the unit’s model name.
5 Click “OK” to exit.
When using Windows Media Player 11
1 Start Windows Media Player 11 on your PC.
2 Select “Library” then “Media Sharing”.
3 Check the “Share my media to” box, select
the unit’s icon, then click “Allow”.
4 Click “OK” to exit.
When using a PC or a NAS with other
DLNA server software installed
Refer to the instruction manual for the device or software
and configure the media sharing settings.
Follow the procedure below to operate the PC music
contents and start playback.
“_” (underscore) will be displayed for characters not supported
by the unit.
1 Press NET repeatedly to select “Server” as
the input source.
2 Use the cursor keys (B / C) to select a music
server and press ENTER.
3 Use the cursor keys to select an item and
press ENTER.
If a song is selected, playback starts and the playback
information is displayed.
y
If playback of a music file selected from the unit is ongoing on
your PC, the playback information is displayed.
You can register the current playback song as a preset (p. 43).
If you press the DISPLAY on the front panel repeatedly, you
can switch the playback information on the front display (p. 42).
Playback of PC music contents
Note
NET USB
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
REPEAT
SHUFFLE
OPTION
RETURN
OPTION
NOW PLAYING
HOME
ENTER
NET
NAS A
SERVER
A
Song A
SERVER
A
33 En
Playing back music stored on media servers (PCs/NAS)
BASIC
OPERATION
English
Use the following remote control keys to control
playback.
y
You can also use a DLNA-compatible Digital Media Controller
(DMC) to control playback. For details, see “DMC Control”
(p.46).
Repeat/shuffle settings
You can configure the repeat/shuffle settings for the
playback of PC music content.
1 When the input source is “SERVER,” press
REPEAT or SHUFFLE on the playback key
repeatedly to select the playback method.
Keys Function
Cursor keys
Select a music file or folder.
ENTER
Starts playback if pressed while
content is selected. Moves down
one level if pressed while a folder
is selected.
RETURN
Moves up one level.
Playback
keys
p/ e
Stops/resumes playback.
s
Stops playback.
b / w
Skips forward/backward.
(while holding down) Searches
forward/backward.
f / a
HOME
Displays the root directory of the
music server.
NOW PLAYING
Displays information about the
song that’s playing.
Playback
keys
Setting Function
REPEAT
Off Turns off the repeat function.
One
Plays back the current song
repeatedly.
All
Plays back all songs in the current
album (folder) repeatedly.
SHUFFLE
Off Turns off the shuffle function.
On
Plays back songs in the current album
(folder) in random order.
34 En
You can listen to Internet radio stations from all over the world.
To use this function, the unit must be connected to the Internet
(p. 14). You can check whether the network parameters (such as
the IP address) are properly assigned to the unit in
“Information” (p.46) in the “Setup” menu.
You may not be able to receive some Internet radio stations.
The unit uses the vTuner Internet radio station database service.
This service may be discontinued without notice.
1 Press NET repeatedly to select “Net Radio”
as the input source.
The station list appears on the front display.
2 Use the cursor keys to select an item and
press ENTER.
If an Internet radio station is selected, playback starts
and the playback information is displayed.
Use the following remote control keys to control
playback.
y
You can register the current playback station as a preset (p. 43).
If you press the DISPLAY on the front panel repeatedly, you
can switch the playback information on the front display (p. 42).
Some information may not be available depending on the
station.
Listening to Internet radio
Notes
LINE 1
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
NOW PLAYING
HOME
ENTER
NET
Bookmarks
NET RADIO
A
Keys Function
Cursor keys
Select the Internet radio station or
category such as the genre.
ENTER
Starts playback if pressed while
an Internet radio station is
selected. Moves down one level if
pressed while a category is
selected.
RETURN
Moves up one level.
Playback keys s
Stops playback.
HOME
Displays the top categories if
pressed during playback.
NOW PLAYING
Displays the playback
information for the Internet radio
station.
JazzST
NET RADIO
A
35 En
Listening to Internet radio
BASIC
OPERATION
English
By registering your favorite Internet radio stations to
“Bookmarks”, you can quickly access to them from the
“Bookmarks” folder in the front display.
1 Select any of Internet radio stations on the
unit.
This operation is necessary to register the radio
station for the first time.
2 Check the vTuner ID of the unit.
You can find the vTuner ID (MAC address of the
unit) in “Information” (p. 46) in the “Setup” menu.
3 Access the vTuner website
(http://yradio.vtuner.com/) with the web
browser on your PC and enter the vTuner ID.
y
To use this feature, you need to create your personal account.
Create your account using your e-mail address.
4 Register your favorite radio stations.
Click the “Add” icon (+) next to the station name.
y
To remove the station from the “Bookmarks” folder, select
“Bookmarks” in the Home screen, and then click the “Remove”
icon (–) next to the station name.
Registering favorite Internet radio
stations (bookmarks)
36 En
The AirPlay function allows you to play back iPod/iTunes
music on the unit via network.
To use this function, the unit and your PC or iPod must be
connected to the same router (p. 14). You can check whether the
network parameters (such as the IP address) are properly assigned
to the unit in “Information” (p.46) in the “Setup” menu.
Follow the procedure below to play back iPod/iTunes
music contents on the unit.
1 Turn on the unit, and start iTunes on the PC
or display the playback screen on the iPod.
If the iPod/iTunes recognizes the unit, the AirPlay
icon ( ) appears.
y
For iPods using iOS 7/8, AirPlay icon is displayed in Control
Center. To access Control Center, swipe up from the bottom of
the screen.
If the icon does not appear, check whether the unit and PC/iPod
are connected to the router properly.
2 On the iPod/iTunes, click (tap) the AirPlay
icon and select the unit (network name of the
unit) as the audio output device.
3 Select a song and start playback.
The unit automatically selects “AirPlay” as the input
source and starts playback. The playback information is
displayed on the front display.
y
If you press the DISPLAY on the front panel repeatedly, you
can switch the playback information on the front display (p. 42).
You can turn on the unit automatically when starting playback
on iTunes or iPod by setting “Standby (Network Standby)”
(p.46) in the “Setup” menu to “On”.
You can edit the network name (the unit’s name on the network)
displayed on iPod/iTunes in “Network Name” (p.47) in the
“Setup” menu.
You can adjust the unit’s volume from the iPod/iTunes during
playback.
When you use iPod/iTunes controls to adjust volume, the
volume may be unexpectedly loud. This could result in
damage to the unit or speakers. If the volume suddenly
increases during playback, stop playback on the iPod/
iTunes immediately.
Playing back iPod/iTunes music via a network (AirPlay)
Note
AirPlay works with iPhone, iPad, and iPod touch with iOS
4.3.3 or later, Mac with OS X Mountain Lion or later, and
Mac and PC with iTunes 10.2.2 or later.
(as of August 2015)
Playback of iPod/iTunes music contents
Note
CAUTION
37 En
Playing back iPod/iTunes music via a network (AirPlay)
BASIC
OPERATION
English
Use the following remote control keys to control playback.
To control iTunes playback with the remote control of the unit,
you need to configure the iTunes preferences to enable iTunes
control from remote speakers in advance.
Keys Functions
Playback
keys
p/ e
Stops/resumes playback.
s
Stops playback.
b / w
Skips forward/backward.
f / a
REPEAT Changes the Repeat settings.
SHUFFLE Changes the Shuffle settings.
Note
38 En
You can play back music files stored on a USB storage device on the unit. Refer to the instruction manuals for the USB
storage device for more information.
The unit supports USB mass storage class devices (e.g., flash memories or portable audio players) using FAT16 or FAT32 format.
The unit supports WAV (PCM format only), AIFF, MP3, WMA, MPEG-4 AAC, FLAC, ALAC and DSD files.
The unit is compatible with sampling rate of up to 192 kHz for WAV, AIFF and FLAC files, 96 kHz for ALAC files, and 48 kHz for
other files.
The unit is compatible with 2.8 MHz/5.6 MHz (1 bit) DSD files.
Do not connect devices other than USB mass storage class devices (such as USB chargers or USB hubs), PCs, card readers, an
external HDD, etc.
USB devices with encryption cannot be used.
Digital Rights Management (DRM) contents cannot be played back.
Some features may not be compatible, depending on the model or manufacturer of the USB storage device.
1 Connect the USB storage device to the USB
jack.
y
If the USB storage device contains many files, it may take time to
load the them. In this case, “Loading...” appears in the front
display.
Disconnect the USB storage device from the USB jack when it
is not in use.
Stop playback of the USB storage device before disconnect it
from the USB jack.
You cannot connect the PC to the USB jack of the unit.
Follow the procedure below to operate the USB storage
device contents and start playback.
“_” (underscore) will be displayed for characters not supported
by the unit.
1
Press USB to select “USB” as the input source.
Playing back music stored on a USB storage device
Notes
Connecting a USB storage device
Notes
BASSINPUT
5V
1A
PHONES
SPEAKERS
AB
Connected
USB
A
VOL.
Playback of USB storage device contents
Note
LINE 1
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
REPEAT
SHUFFLE
OPTION
RETURN
USB
NOW PLAYING
HOME
ENTER
Bluse
USB
A
VOL.
39 En
Playing back music stored on a USB storage device
BASIC
OPERATION
English
2 Use the cursor keys to select an item and
press ENTER.
If a song is selected, playback starts and the playback
information is displayed.
y
You can register the current playback song as a preset (p. 43).
If you press the DISPLAY on the front panel repeatedly, you
can switch the playback information on the front display (p. 42).
Use the following remote control keys to control playback.
Repeat/shuffle settings
You can configure the repeat/shuffle settings for playback
of USB storage device contents.
1 If the input source is “USB,” press REPEAT
or SHUFFLE on the playback keys repeatedly
to select the playback method.
Keys Function
Cursor keys
Select a music file or folder.
ENTER
Starts playback if pressed while a
music file is selected. Moves down
one level if pressed while a folder is
selected.
RETURN
Moves up one level.
Playback
keys
p/ e
Stops/resumes playback.
s
Stops playback.
b / w
Skips forward/backward.
f / a
HOME
Displays the root directory of the
USB device.
NOW PLAYING
Displays information about the
song thats playing.
Track #3
USB
A
Playback
keys
Setting Function
REPEAT
Off Turns off the repeat function.
One
Plays back the current song
repeatedly.
All
Plays back all songs in the current
album (folder) repeatedly.
SHUFFLE
Off Turns off the shuffle function.
On
Plays back songs in the current album
(folder) in random order.
40 En
You can play back iPod music on the unit using a USB cable supplied with the iPod.
An iPod may not be detected by the unit or some features may not
be compatible, depending on the model or software version of the
iPod.
Connect your iPod to the unit with the USB cable supplied
with the iPod.
1 Connect the USB cable to the iPod.
2 Connect the USB cable to the USB jack.
y
If “Standby (Network Standby)” (p.46) in the “Setup” menu is set
to “Off”, the iPod will continue to charge up to 4 hours if the unit
goes into standby mode while the iPod is charging.
Disconnect the iPod from the USB jack when it is not in use.
Follow the procedure below to operate the iPod contents
and start playback.
“_” (underscore) will be displayed for characters not supported
by the unit.
1 Press USB to select “USB” as the input
source.
2 Use the cursor keys to select an item and
press ENTER.
If a song is selected, playback starts and the playback
information is displayed.
y
If you press the DISPLAY on the front panel repeatedly, you
can switch the playback information on the front display (p. 42).
To operate the iPod manually to select content or control
playback, switch to the simple play mode (p. 41).
Playing back iPod music
Note
Made for
iPod touch (2nd, 3rd, 4th and 5th generation)
iPod nano (2nd, 3rd, 4th, 5th, 6th and 7th generation)
iPhone 6, iPhone 6 Plus, iPhone 5s, iPhone 5c, iPhone 5,
iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G
(as of August 2015)
Connecting an iPod
Note
BASSINPUT
5V
1A
DIMMER MO
DISPLAY
PHONES
SPEAKERS
AB
Connected
USB
A
VOL.
Playback of iPod content
Note
LINE 1
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
REPEAT
SHUFFLE
OPTION
RETURN
USB
NOW PLAYING
HOME
ENTER
Music
USB
A
VOL.
Track #1
USB
A
VOL.
41 En
Playing back iPod music
BASIC
OPERATION
English
Use the following remote control keys to control playback.
Operating the iPod itself or remote
control (simple play)
1 Press MODE on the front panel to switch to
the simple play mode.
Between the simple play mode, only the input name
is displayed on the front display. If you confirm the
playback information, see the iPod screen.
y
If you want to exit the simple play mode, press MODE again.
2 Operate your iPod itself or the remote control
to start playback.
Use the following remote control keys to control
playback on the simple play mode.
Repeat/shuffle settings
You can configure the repeat/shuffle settings of your iPod.
1 If the input source is “USB,” press REPEAT
or SHUFFLE on the playback keys repeatedly
to select the playback method.
y
The operation or display of repeat/shuffle may differ, depending
on the type or software version of iPod used.
Keys Function
Cursor keys
Select a music file, album or genre.
ENTER
Starts playback if pressed while a
music file is selected. Moves down
one level if pressed while an album
or genre is selected.
RETURN
Moves up one level.
Playback
keys
p/ e
Stops/resumes playback.
s
Stops playback.
b / w
Skips forward/backward.
(while holding down) Searches
forward/backward.
f / a
HOME
Displays the top menu of the iPod.
NOW PLAYING
Displays information about the
song thats playing.
Operational remote
control keys
Function
Cursor keys
Select an item.
ENTER
Confirms the selection.
RETURN
Returns to the previous state.
Playback
keys
p/ e
Starts playback or stops playback
temporarily.
s
Stops playback.
b / w
Skips forward/backward.
(while holding down) Searches
forward/backward.
f / a
Playback
keys
Setting Function
REPEAT
Off Turns off the repeat function.
One
Plays back the current song
repeatedly.
All Plays back all songs repeatedly.
SHUFFLE
Off Turns off the shuffle function.
Songs Plays back songs in random order.
Albums Plays back albums in random order.
42 En
When you select a network source or USB as the input source, you can switch playback information on the front display.
1 Press DISPLAY.
Each time you press the key, the displayed item
changes.
About 3 seconds later, the corresponding information
for the displayed item appears.
Switching information on the front display
Input source Item
Bluetooth
Server
AirPlay
USB (include
iPod)
Track (song title), Artist (artist name),
Album (album name), Time
Net Radio
Track (song title), Album (album name),
Time, Station (station name)
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
Track
INFO
A
Track #1
SERVER
A
43 En
BASIC
OPERATION
English
When you select network sources and USB as the input source, you can register the current playback song or streaming
station as a preset up to 40.
You can then easily recall any preset song/station by selecting its preset number.
The following input sources can be set as presets.
Server, Net Radio, USB (except iPod) and streaming services.
1 Playback a song or streaming station you
want to register.
2 Hold down MEMORY for more than 3
seconds.
The first time that you register a song/station, the
selected song/station will be registered to the preset
number “01”. Thereafter, each song/station you select
will be registered to the next empty (unused) preset
number after the most recently registered number.
y
To select a preset number for registering, press PRESET j / i or
the cursor keys (D/E).
3 Press MEMORY again to register preset.
1 Select the input source you want to recall the
preset.
2 Press PRESET j / i to select a preset
number.
3 Press ENTER to recall preset.
Registering the current playback song/station (Preset function)
Registering to a preset
NET USB
TUNER
PRESET
TUNING
BAND
MEMORY
ENTER
PRESET j / i
MEMORY
ENTER
01:Empty
MEMORY
A
Recalling a preset
44 En
ADVANCED OPERATION
You can configure separate playback settings for different playback sources. This menu allows you to easily configure
settings during playback.
1 Press OPTION.
2 Use the cursor keys to select an item and
press ENTER.
y
To return to the previous state during menu operations, press
RETURN.
3 Use the cursor keys (D / E) to select a setting.
4 To exit from the menu, press OPTION.
y
Available items vary depending on the selected input source.
Volume Trim
Corrects volume differences between input sources. If you
are bothered by volume differences when switching
between input sources, use this function to correct it.
y
This setting is applied separately to each input source.
Setting range
-10.0 dB to 0.0 dB to +10.0 dB (0.5 dB increments)
Default
0.0 dB
Signal Info.
Displays information about audio signal.
Choices
y
To switch the information on the front display, press the cursor
keys (B / C) repeatedly.
Vol.Interlock (Volume interlock)
Enables/disables volume controls from iTunes/iPod via
AirPlay.
Settings
Configuring playback settings for different playback sources
(Option menu)
Option menu items
Item Function Page
Volume Trim
Corrects volume differences between
input sources.
44
Signal Info.
Displays information about the audio
signal.
44
Auto Preset
Automatically registers FM radio
stations with strong signals as presets.
26
Clear Preset
Clear radio stations registered to preset
numbers.
28
Vol.Interlock
(Volume interlock)
Enables/Disables volume controls from
iTunes/iPod via AirPlay.
44
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
OPTION
ENTER
VOL.
A
Volume Trim
OPTION
FORMAT Audio format of the input signal
SAMPLING
The number of samples per second of the input
digital signal
Off Disables volume controls from iTunes/iPod.
Ltd
(default)
Enables volume controls from iTunes/iPod within
the limited range (-80.0 dB to -20.0 dB and mute).
Full
Enables volume controls from iTunes/iPod in the
full range (-80.0 dB to +16.5 dB and mute).
45 En
English
ADVANCED
OPERATION
You can configure the unit’s various functions.
1 Press SETUP.
2 Use the cursor keys (B / C) to select a menu.
3 Press ENTER.
4 Use the cursor keys (D / E) to select a setting
and press ENTER.
y
To return to the previous state during menu operations, press
RETURN.
5 Exit from the menu, press SETUP.
Configuring various functions (Setup menu)
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
Network
SETUP
A
Max Volume
SETUP
A
+16.5dB
MAX VOL
A
Setup menu items
Menu item Function
Page
Network
Connection
Selects the network
connection method.
46
Information
Displays the network
information on the unit.
46
IP Address
Configures the network
parameters (such as IP
address).
46
DMC
Control
Selects whether to allow a
DLNA-compatible Digital
Media Controller (DMC) to
control playback.
46
Standby
(Network
Standby)
Selects whether to enable/
disable the function that turns
on the unit from other
network devices.
46
Network
Name
Edits the network name (the
unit’s name on the network)
displayed on other network
devices.
47
Update
(Network
Update)
Updates the firmware via the
network.
47
Bluetooth
On/Off
Enables/disables the
Bluetooth functions.
47
Standby
(Bluetooth
Standby)
Selects whether to enable/
disable the function that turns
on the unit from Bluetooth
devices (Bluetooth standby).
47
Audio
Receive
Receives audio settings from
the Bluetooth device.
47
Audio Send
Transmit audio from the unit
to Bluetooth speakers or
headphones.
47
Max Volume
Sets the maximum volume to
prevent excessive loudness.
48
Initial Volume
Sets the initial volume for
when this receiver is turned
on.
48
AutoPowerStdby
(Auto Power Standby)
Sets the amount of time for
the auto standby function.
48
ECO Mode
Enables/disables the eco
mode (power saving mode).
48
46 En
Configuring various functions (Setup menu)
Configures the network settings.
Connection
Selects the network connection method.
Information
Displays the network information on the unit.
IP Address
Configures the network parameters (such as IP address).
DHCP
Select whether to use a DHCP server.
Manual network settings
1 Set “DHCP” to “Off”.
2 Use the cursor keys (B / C) to select a
parameter type.
3 Use the cursor keys (D / E) to select the edit
position.
(Example: IP address setting)
Use the cursor keys (D / E) to switch between
segments (Address1, Address2...) of the address.
4 Use the Cursor keys (B / C) to change a
value.
5 To exit from the menu, press SETUP.
DMC Control
Selects whether to allow DLNA-compatible Digital Media
Controller (DMC) to control playback.
y
A Digital Media Controller (DMC) is a device that can control
other network devices through the network. When this function is
enabled, you can control playback of the unit from DMCs (such
as Windows Media Player 12) on the same network.
Standby (Network Standby)
Selects whether the unit can be turned on from other
network devices (network standby).
Network
Wired
Select this option when you want to connect
the unit to a network with a commercially-
available network cable (p. 16).
Wireless
Select this option when you want to connect
the unit to a network via the wireless router or
access point (p. 17, 18, 19).
WirelessDirect
Select this option when you want to connect a
mobile device to the unit directly. For details
on settings, see “Connecting a mobile device
to the unit directly (Wireless Direct)” (p. 20).
Extend
Displays connection method of the MusicCast
Network.
NEW FW
Available
Appears if an update for this unit’s firmware is
available (p. 51).
STATUS The connection status of the network.
MC NET
Status of the MusicCast Network. If “Ready”
appears, you can use the MusicCast
CONTROLLER app.
MAC
Displays MAC address of the unit. MAC
address will vary depending on the connection
method (wired LAN connection or wireless
LAN / Wireless Direct connection).
SSID
(When using wireless LAN connection or
Wireless Direct ) The SSID of this unit on the
wireless network.
IP IP address
SUBNET Subnet mask
GATEWAY The IP address of the default gateway
DNS P The IP address of the primary DNS server
DNS S The IP address of the secondary DNS server
VTUNER The ID of the Internet radio (vTuner)
Off
Does not use a DHCP server. Configure the
network parameters manually. For details, see
“Manual network settings”.
On (default)
Uses a DHCP server to automatically obtain the
unit’s network parameters (such as IP address).
IP Specifies an IP address.
SUBNET Specifies a subnet mask.
GATEWAY Specifies the IP address of the default gateway.
DNS P
Specifies the IP address of the primary DNS
server.
DNS S
Specifies the IP address of the secondary DNS
server.
Disable Does not allow DMCs to control playback.
Enable
(default)
Allows DMCs to control playback.
Off Disables the network standby function.
On
Enables the network standby function. (The unit
consumes more power than when “Off” is
selected.)
Auto
(Default)
Enables the network standby function. The unit is
set to the power saving mode when the unit is
disconnected from the network.
Address1•••192
NETWORK
A
47 En
Configuring various functions (Setup menu)
English
ADVANCED
OPERATION
Network Name
Edits the network name (the unit’s name on the network)
displayed on other network devices.
1 Select “Network Name”.
2 Press ENTER twice to enter the name edit
display.
3 Use the cursor keys (D / E) to move the edit
position and the cursor keys (B / C) to select
a character.
You can insert / delete a character, by pressing
PRESET i (insert) or PRESET j (delete).
4 To confirm the new name, press ENTER.
5 To exit from the menu, press SETUP.
Update (Network Update)
Updates the firmware via the network.
Configures the Bluetooth settings.
On/Off
Enables/disables the Bluetooth function (p. 29).
Standby (Bluetooth Standby)
Selects whether to enable/disable the function that turns
on the unit from Bluetooth devices (Bluetooth standby). If
this function is set to “On”, the unit automatically turns on
when a connect operation is performed on the Bluetooth
device.
y
This setting is not available when “Standby (Network Standby)”
(p. 46) is set to “Off”.
Audio Receive
Receives audio settings from the Bluetooth device.
Audio Send
Transmit audio from the unit to Bluetooth speakers or
headphones.
Perform
Update
Starts the process to update the unit’s firmware.
For details, see “Updating the unit’s firmware via
the network” (p. 51).
Version
Displays the version of the firmware installed on
the unit.
ID Displays the system ID number.
Network Name
NETWORK
A
R-N602 XXXXXX
NAME
A
R-N602 XXXXXX
NAME
A
Bluetooth
Off Disables the Bluetooth function.
On (Default)
Enables the Bluetooth function. Immediately
after selecting the “On”, output of the network
source is paused.
Off Disables the Bluetooth standby function.
On (Default)
Enables the Bluetooth standby function. (The
unit consumes more power than when “Off” is
selected.)
Disconnect
Disconnects the connected Bluetooth device. To
disconnect the Bluetooth device, press ENTER
on the remote control.
Off (Default) Audio can not be transmitted.
On
Enables audio transmission. Specify the audio
transmission settings using the dedicated
MusicCast CONTROLLER app for mobile
devices.
48 En
Configuring various functions (Setup menu)
Sets the maximum volume to prevent excessive loudness.
Setting range
-30 dB to +15.0 dB / +16.5 dB (5 dB step)
Default
+16.5 dB
Sets the initial volume when the receiver is turned on.
Setting range
Off, Mute, -80.0 dB to +16.5 dB (0.5 dB Step)
Default
Off
Enables/disables the auto-standby function. If you do not
operate the unit for the specified time, the unit will
automatically go into standby mode.
y
Just before the unit enters standby mode, “AutoPowerStdby”
appears and then countdown starts in the front display.
Enables/disables the eco (power saving) mode. When the
eco mode is enabled, you can reduce the unit’s power
consumption.
The new setting will take effect after the unit is restarted.
Be sure to press ENTER to restart the unit after selecting a
setting.
When “ECO Mode” is set to “On”, the front display may become
dark.
Max Volume
Initial Volume
AutoPowerStdby
(Auto Power Standby)
Off
(Default)
Does not set the unit to standby mode
automatically.
On
Sets the unit to standby mode automatically.
While NET, BLUETOOTH or USB is selected as
the input source, the unit will switch to standby
mode if the selected source is not played back for
20 minutes.
For all input sources, the unit will switch to
standby mode if it is not operated for 8 hours.
ECO Mode
Off (default) Disables the eco mode.
On Enables the eco mode.
Note
49 En
English
ADVANCED
OPERATION
Configure the system settings of the unit while viewing the front display.
1 Turn off the unit.
2
While holding down RETURN on the front
panel, press
A (power).
3 Rotate SELECT/ENTER to select an item.
4 Press SELECT/ENTER to select a setting.
5 Press A (power) to set the unit to turn off and
turn it on again.
The new settings take effect.
Change the unit’s speaker impedance settings depending
on the impedance of the speakers connected.
Settings
When using multiple receivers in the same room, setting
the remote control ID of this unit to ID1 (and setting the
another receiver to other than ID1) can prevent
interference from other remote controls.
Settings
ID1, AUTO (default)
Restores the default settings for the unit.
Settings
Configuring the system settings (ADVANCED SETUP menu)
ADVANCED SETUP menu items
Item Function Page
SP IMP.
Changes the speaker impedance
setting.
49
REMOTE ID Selects the unit’s remote control ID. 49
TU
Changes the FM/AM tuning frequency
setting.
49
INIT Restores the default settings. 50
UPDATE Updates the firmware. 50
VERSION
Checks the version of firmware
currently installed on the unit.
50
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
Changing the speaker impedance
setting (SP IMP.)
4 MIN
Select this option when you connect speakers with
an impedance of 4 ohms to less than 8 ohms to the
unit.
8 MIN
(Default)
Select this option when you connect speakers with
an impedance of 8 ohms or more to the unit.
Selecting the remote control ID
(REMOTE ID)
Changing the FM/AM tuning
frequency setting (TU)
FM100/AM10
Select this when you want to adjust the FM
frequency by 100-kHz steps and AM by 10-kHz
steps.
FM50/AM9
(default)
Select this when you want to adjust the FM
frequency by 50-kHz steps and AM by 9-kHz steps.
SP IMP.••8¬MIN
REMOTE ID•AUTO
TU••••FM50/AM9
50 En
Configuring the system settings (ADVANCED SETUP menu)
Restores the default settings for the unit.
Choices
New firmware that provides additional features or product
improvements will be released as needed. If the unit is
connected to the Internet, you can download the firmware
via the network. For details, refer to the information
supplied with updates.
Firmware update procedure
Do not perform this procedure unless firmware update is
necessary. Also, make sure you read the information
supplied with updates before updating the firmware.
1 Press SELECT/ENTER repeatedly to select
“USB” or “NETWORK” and press DISPLAY to
start firmware update.
Choices
y
If the unit detects newer firmware over the network, “NEW FW
Available” appears as the “Information” menu item in
“Network”. In this case, you can also update the unit’s firmware
by following the procedure in “Updating the unit’s firmware via
the network” (p. 51).
Check the version of firmware currently installed on the
unit.
y
You can also check the firmware version in “Update (Network
Update)” (p. 47) in the “Setup” menu.
It may take a while until the firmware version is displayed.
Restoring the default settings (INIT)
ALL Restores the default settings for the unit.
NETWORK
Initialize all of the network, Bluetooth and USB
settings. When performing the initialization, the
preset (p. 43) registered by NET/USB input will
be cleared.
CANCEL Does not perform an initialization.
Updating the firmware (UPDATE)
USB Update the firmware using a USB memory device.
NETWORK Update the firmware via the network.
INIT••••CANCEL
UPDATE•NETWORK
Checking the firmware version
(VERSION)
VERSION••xx.xx
51 En
English
ADVANCED
OPERATION
New firmware that provides additional features or product improvements will be released as needed. If the unit is
connected to the Internet, you can download the firmware via the network and update it.
y
You can also update the firmware using the USB memory device
from the “ADVANCED SETUP” menu (p. 50).
1 Press SETUP.
2 Use the cursor keys (B / C) to select
“Network” and press ENTER.
3 Use the cursor keys (B / C) to select
“Information” and press ENTER.
If new firmware is available, “NEW FW Available”
appears on the front display.
4 Press RETURN to return the previous state.
5 Use the cursor keys (B / C) to select
“Update” and press ENTER.
6 To start the firmware update, press ENTER.
The unit to restart and the firmware update starts.
y
To cancel the operation without updating the firmware, press
SETUP.
7 If “UPDATE SUCCESS” appears on the front
display, press A (power) on the front panel.
The firmware update is complete.
Updating the unit’s firmware via the network
Do not operate the unit or disconnect the power cable or network cable during firmware update. Firmware update takes about 20
minutes or more (depending on your Internet connection speed).
If the unit is connected to the wireless network via a wireless network adapter, network update may not be possible depending on
the condition of the wireless connection. In this case, update the firmware using the USB memory device (p. 50).
Notes
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
Available
NEW FW
Perform Update
UPDATE
52 En
ADDITIONAL INFORMATION
Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or
if the instructions below do not help, set this unit to standby mode, disconnect the power cable, and contact the nearest
authorized Yamaha dealer or service center.
General
Troubleshooting
Problem Cause Remedy
See
page
The power does not
turn on.
The protection circuitry has been activated
three times consecutively. If the unit is in
this condition, the standby indicator on the
unit blinks when you try to turn on the
power.
As a safety precaution, capability to turn on the power
is disabled. Contact your nearest Yamaha dealer or
service center to request repair.
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
The protection circuitry has been activated
because of a short circuit, etc.
Check that the speaker wires are not touching each
other and then turn the power of this unit back on.
12
The internal microcomputer has frozen,
due to an external electric shock (such as
lightning or excessive static electricity) or
to a drop in the power supply voltage.
Turn OFF the A (Power) on the front panel and turn it
ON again after at least 15 seconds elapse. (If the
problem persists, disconnect the power cable from the
AC wall outlet and plug it again.)
The power does not
turn off.
The internal microcomputer has frozen,
due to an external electric shock (such as
lightning or excessive static electricity) or
to a drop in the power supply voltage.
Turn OFF the A (Power) on the front panel and turn it
ON again after at least 15 seconds elapse. (If the
problem persists, disconnect the power cable from the
AC wall outlet and plug it again.)
No sound. Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
11
No appropriate input source has been
selected.
Select an appropriate input source with the INPUT
selector on the front panel (or one of the input
selection key on the remote control).
22
The SPEAKERS A/B switches are not set
properly.
Turn on the corresponding SPEAKERS A or
SPEAKERS B.
22
Speaker connections are not secure. Secure the connections.
11
Output has been muted. Turn off the mute.
9
The Max volume or Initial volume setting
is set too low.
Check the settings for “Max Volume” and “Initial
Volume” in the “Setup” menu.
48
The component corresponding to the
selected input source is turned off or is not
playing.
Turn the component on and make sure it is playing.
The audio output of a device connected to
a digital audio input (COAXIAL/
OPTICAL jacks) is set to other than PCM.
Set the audio output of the connected device to PCM.
The sound suddenly
goes off.
The protection circuitry has been activated
because of a short circuit, etc.
Set the speaker impedance to match your speakers.
49
Check that the speaker wires are not touching each
other and then turn the power of this unit back on.
12
This unit has become too hot. Make sure the openings on the top panel are not
blocked.
The auto power standby function has
turned this unit off.
Change the auto power standby (“AutoPowerStdby”
in the “Setup” menu) to turn off.
48
53 En
Troubleshooting
English
ADDITIONAL
INFORMATION
Only the speaker on
one side can be
heard.
Incorrect cable connections. Connect the cables properly. If the problem persists,
the cables may be defective.
11
Incorrect setting for the speaker balance. Set the BALANCE control to the appropriate
position.
23
There is a lack of bass
and no ambience.
The + and – wires are connected in
reverse at the amplifier or the speakers.
Connect the speaker wires to the correct + and –
phase.
12
A “humming” sound
can be heard.
Incorrect cable connections. Connect the audio plugs firmly. If the problem
persists, the cables may be defective.
11
No connection from the turntable to the
GND terminal.
Make the GND connection between the turntable and
this unit.
11
The volume level is
low while playing a
record.
The record is being played on a turntable
with an MC cartridge.
The turntable should be connected to this unit through
the MC head amplifier.
The sound is
degraded when
listening with the
headphones
connected to the CD
player or the tape
deck connected to
this unit.
The power of this unit is turned off, or this
unit is set to standby mode.
Turn on the power of this unit.
The sound level is
low.
The loudness control function is
operating.
Turn down the volume, set the LOUDNESS control
to the FLAT position, and then adjust the volume
again.
23
Problem Cause Remedy
See
page
54 En
Troubleshooting
Tuner
Problem Cause Remedy
See
page
FM
FM stereo
reception is
noisy.
The particular characteristics of the FM
stereo broadcasts being received may
cause this problem when the transmitter is
too far away or the antenna input is poor.
Check the antenna connections.
Try using a high-quality directional FM antenna.
13
Switch to monaural mode.
25
There is
distortion, and
clear reception
cannot be
obtained even
with a good FM
antenna.
There is multipath interference. Adjust the antenna position to eliminate the multipath
interference.
The desired
station cannot
be tuned in
with the
automatic
tuning method.
The signal is too weak. Try using a high-quality directional FM antenna.
13
Try using the manual tuning method.
25
FM/
AM
NO PRESETS
is displayed.
No preset stations are registered. Register stations you want to listen to as preset
stations before operation.
26
AM
The desired
station cannot
be tuned in
with the
automatic
tuning method.
The signal is weak or the antenna
connections are loose.
Tighten the AM antenna connections and orient it for
the best reception.
Try using the manual tuning method.
25
Automatic
station preset
does not work.
Automatic station preset is not available
for AM stations.
Use manual station preset.
27
There are
continuous
crackling and
hissing noises.
The noises may result from lightning,
fluorescent lamps, motors, thermostats or
other electrical equipment.
Try using an outdoor antenna and a ground wire.
This will help somewhat, but it is difficult to
eliminate all noise.
There are
buzzing and
whining noises.
A TV set is being used nearby. Move this unit away from the TV set.
55 En
Troubleshooting
English
ADDITIONAL
INFORMATION
Bluetooth
Problem Cause Remedy
See
page
A Bluetooth
connection cannot be
established.
The Bluetooth function of the unit is
disabled.
Enable the Bluetooth function in the “Setup” menu.
47
Another Bluetooth device is already
connected to the unit.
Terminate the current Bluetooth connection and then
establish a new connection.
47
The unit and the Bluetooth device are too
far apart.
Move the Bluetooth device closer to the unit.
There is a device (such as microwave
oven and wireless LAN) that outputs
signals in the 2.4 GHz frequency band
nearby.
Move the unit away from those devices.
The Bluetooth device does not support
A2DP.
Use a Bluetooth device that supports A2DP.
Since this unit has been paired with more
than 20 Bluetooth devices, pairing
information has been deleted.
Try pairing again.
This unit can be paired with a maximum total of 20
Bluetooth devices for reception and transmission.
When the 21st device is registered, the least
frequently used pairing information is deleted.
29
No sound is
produced, or the
sound is interrupted
during playback.
The volume of the Bluetooth device is set
too low.
Turn up the volume of the Bluetooth device.
The Bluetooth device is not set to send
audio signals to the unit.
Switch the audio output of the Bluetooth device to the
unit.
The Bluetooth connection has been
terminated.
Establish a Bluetooth connection between the
Bluetooth device and the unit again.
29
The unit and the Bluetooth device are too
far apart.
Move the Bluetooth device closer to the unit.
There is a device (such as microwave
oven and wireless LAN) that outputs
signals in the 2.4 GHz frequency band
nearby.
Move the unit away from those devices.
56 En
Troubleshooting
USB and network
Problem Cause Remedy
See
page
The unit does not
detect the USB
device.
The USB device is not connected to the
USB jack securely.
Turn off the unit, reconnect your USB device, and
turn the unit on again.
The file system of the USB device is not
FAT16 or FAT32.
Use a USB device with FAT16 or FAT32 format.
Folders and files in
the USB device
cannot be viewed.
The data in the USB device is protected
by the encryption.
Use a USB device without an encryption function.
The network feature
does not function.
The network parameters (IP address) have
not been obtained properly.
Enable the DHCP server function on your router and
set “DHCP” in the “Setup” menu to “On” on the unit.
If you want to configure the network parameters
manually, check that you are using an IP address
which is not used by other network devices in your
network.
46
The unit cannot
connect to the
Internet via a wireless
router (access point).
The wireless router (access point) is
turned off.
Turn on the wireless router (access point).
The unit and the wireless router (access
point) are too far apart.
Place the unit and the wireless router (access point)
closer to each other
There is an obstacle between the unit and
the wireless router (access point).
Move the unit and the wireless router (access point)
in a location where there are no obstacles between
them.
Wireless network is
not found.
Microwave ovens or other wireless
devices in your neighborhood might
disturb the wireless communication.
Turn off these devices.
Access to the network is restricted by the
firewall settings of the wireless router
(access point).
Check the firewall setting of the wireless router
(access point).
The unit does not
detect the PC.
The media sharing setting is not correct. Configure the sharing setting and select the unit as a
device to which music contents are shared.
31
Some security software installed on your
PC is blocking the access of the unit to
your PC.
Check the settings of security software installed on
your PC.
The unit and PC are not in the same
network.
Check the network connections and your router
settings, and then connect the unit and the PC to the
same network.
14
The files in the media
server (PCs/NAS)
cannot be viewed or
played back.
The files are not supported by the unit or
the media server.
Use the file format supported by both the unit and the
media server. For information about the file formats
supported by the unit, see “Playing back music stored
on media servers (PCs/NAS)”.
31
The Internet radio
cannot be played.
The selected Internet radio station is
currently not available.
There may be a network problem at the radio station,
or the service may have been stopped. Try the station
later or select another station.
The selected Internet radio station is
currently broadcasting silence.
Some Internet radio stations broadcast silence at
certain of times of the day. Try the station later or
select another station.
Access to the network is restricted by the
firewall settings of your network devices
(such as the router).
Check the firewall settings of your network devices.
The Internet radio can be played only when it passes
through the port designated by each radio station. The
port number varies depending on the radio station.
The iPod does not
recognize the unit
when using AirPlay.
The unit is connected to a multiple SSID
router.
Access to the unit might be restricted by the network
separation function on the router. Connect the iPod to
the SSID which can access the unit.
Firmware update via
the network is failed.
It may not be possible depending on the
condition of the network.
Update the firmware via the network again or use a
USB memory device.
50
57 En
Troubleshooting
English
ADDITIONAL
INFORMATION
Remote control
Problem Cause Remedy
See
page
The remote control
does not work nor
function properly.
Wrong distance or angle. The remote control will function within a maximum
range of 6 m (20 ft) and no more than 30 degrees off-
axis from the front panel.
10
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
The batteries are weak. Replace all batteries.
58 En
Error indications on the front display
Message Cause Remedy
Access denied Access to the PC is denied. Configure the sharing settings and select the unit as a device to
which music contents are shared (p. 31).
Access error The unit cannot access the USB device. Turn off the unit and reconnect your USB device. If the problem
persists, try another USB device.
The unit cannot access the iPod. Turn off the iPod and turn it on again.
The connected iPod is not supported by
the unit.
Use an iPod supported by the unit (p. 40).
There is a problem with the signal path
from the network to the unit.
Make sure your router and modem are turned on.
Check the connection between the unit and your router (or hub)
(p. 14).
Check SP Wires The speaker cables short circuit. Twist the bare wires of the cables firmly and connect to the unit
and speakers properly.
No content There are no playable files in the selected
folder.
Select a folder that contains files supported by the unit.
Please wait The unit is preparing for connecting to the
network.
Wait until the message disappears. If the message stays more than
3 minutes, turn off the unit and turn it on again.
Unable to play The unit cannot play back the songs stored
on the iPod for some reason.
Check the song data. If it cannot be played on the iPod itself, the
song data or storage area may be defective.
The unit cannot play back the songs stored
on the PC for some reason.
Check if the format of files you are trying to play is supported by
the unit. For information about the formats supported by the unit,
see “Playing back music stored on media servers (PCs/NAS)” (p.
31). If the unit supports the file format, but still cannot play back
any files, the network may be overloaded with heavy traffic.
Version error Firmware update is failed. Update the firmware again.
59 En
English
ADDITIONAL
INFORMATION
“Made for iPod” and “Made for iPhone” mean that an
electronic accessory has been designed to connect
specifically to iPod or iPhone, respectively, and has been
certified by the developer to meet Apple performance
standards.
Apple is not responsible for the operation of this device or
its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod or
iPhone may affect wireless performance.
AirPlay, iPhone, iPod, iPod nano, iPod touch and iTunes
are trademarks of Apple Inc., registered in the U.S. and
other countries.
DLNA™ and DLNA CERTIFIED™ are trademarks or
registered trademarks of Digital Living Network Alliance.
All rights reserved. Unauthorized use is strictly
prohibited.
Windows™
Windows is a registered trademark of Microsoft
Corporation in the United States and other countries.
Internet Explorer, Windows Media Audio and Windows
Media Player are either registered trademarks or
trademarks of Microsoft Corporation in the United States
and/or other countries.
Android™
Android and Google Play are trademarks of Google, Inc.
The Wi-Fi CERTIFIED Logo is a certification mark of the
Wi-Fi Alliance.
The Wi-Fi Protected Setup Identifier Mark is a mark of the
Wi-Fi Alliance.
Wi-Fi, Wi-Fi Alliance, Wi-Fi CERTIFIED, Wi-Fi
Protected Setup, WPA and WPA2 are trademark or
registeredrademark of Wi-Fi Alliance.
The Bluetooth
®
word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by Yamaha Corporation is under license.
Bluetooth protocol stack (Blue SDK)
Copyright 1999-2014 OpenSynergy GmbH
All rights reserved. All unpublished rights reserved.
Explanations regarding GPL
This product utilizes GPL/LGPL open-source software in
some sections. You have the right to obtain, duplicate,
modify, and redistribute this open-source code only. For
information on GPL/LGPL open source software, how to
obtain it, and the GPL/LGPL license, refer to the Yamaha
Corporation website
(http://download.yamaha.com/sourcecodes/musiccast/).
MusicCast is a trademark or registered trademark of
Yamaha Corporation.
Trademarks
60 En
Network
Input jack: NETWORK x 1 (100Base-TX/10Base-T)
PC client function
Compatible with DLNA ver. 1.5
AirPlay supported
Internet radio
Streaming service
Wi-Fi function
Capable of WPS
Capable of sharing with iOS devices by wireless connection and
USB connection
Capable of direct connection with mobile device
Available security method: WEP, WPA2-PSK (AES), Mixed Mode
Radio frequency band: 2.4 GHz
Wireless network standard: IEEE 802.11 b/g/n
Bluetooth
Source function
This unit to sink device (ex. Bluetooth headphone)
Supported codec ..........................................................................SBC
Sink function
Source device to this unit (ex. smartphone/tablet)
Supported codec ............................................................... SBC, AAC
Capable of play/stop operation from sink device
Bluetooth version .........................................................Ver. 2.1+EDR
Supported profile........................................................A2DP, AVRCP
Wireless output....................................................... Bluetooth Class 2
Maximum communication distance
........................................................10 m (33 ft) without interference
USB
Input jack: USB x 1 (USB2.0)
Capable of iPod, mass storage class USB memory
Current supply capacity: 1.0 A
Audio
Minimum RMS output power
(20 Hz to 20 kHz, 0.04% THD, 8 ) ....................... 80 W + 80 W
Dynamic power per channel (IHF) (8/6/4/2 )
............................................................................ 105/125/150/178 W
Maximum power per channel (1 kHz, 0.7% THD, 4 )
[U.K. and Europe models] ................................................... 105 W
IEC power (1 kHz, 0.04% THD, 8 )
[U.K. and Europe models] ..................................................... 84 W
Power band width (main L/R)
(0.06%THD 40.0 W, 8) ......................................10 Hz to 50 kHz
Damping factor (SPEAKERS A)
1 kHz, 8 ..................................................................150 or more
Maximum effective output power (JEITA)
(1 kHz, 10% THD, 8 )
[Asia and General models]....................................................115 W
Input sensitivity/input impedance
PHONO (MM) ......................................................... 3.5 mV/47 k
CD, etc. .................................................................. 200 mV/47 k
Maximum input signal
PHONO (MM) (1 kHz, 0.003% THD) ..................60 mV or more
CD, etc. (1 kHz, 0.5% THD).....................................2.2 V or more
Output level/output impedance
CD, etc. (input 1 kHz, 200 mV)
OUT .................................................................... 200 mV/1.1 k
SUBWOOFER PRE OUT .................................... 4.0 V / 1.2 k
(Cut off frequency) .............................................................90 Hz
PHONES (8 load)............................................. 410 mV/470
Frequency response
CD, etc. (20 Hz to 20 kHz) ........................................... 0 ± 0.5 dB
CD, etc. (10 Hz to 100 kHz, PURE DIRECT on) ......... 0 ± 1.0 dB
RIAA equalization deviation
PHONO (MM)...................................................................± 0.5 dB
Total harmonic distortion
PHONO (MM) to OUT
(20 Hz to 20 kHz, 3 V) . ....................................... 0.025% or less
CD, etc. to SPEAKERS
(20 Hz to 20 kHz, 40.0 W, 8 ) ........................... 0.015% or less
Signal to noise ratio (IHF-A Network)
PHONO (MM) (input shorted, 5 mV)......................87 dB or more
CD, etc. (input shorted, 200 mV) ...........................100 dB or more
Residual noise (IHF-A network) .............................................30 µV
Channel separation
CD, etc. (5.1 k input shorted, 1/10 kHz) ......... 65/50 dB or more
Tone control characteristics
BASS
Boost/cut (20 Hz) ...........................................................± 10 dB
Turnover frequency .......................................................... 350 Hz
TREBLE
Boost/cut (20 kHz) .........................................................± 10 dB
Turnover frequency ......................................................... 3.5 kHz
Continuous loudness control
Attenuation 1 kHz.................................................................-30 dB
Gain tracking error (+16.5 to -80 dB) ..........................0.5 dB or less
Digital input (OPTICAL/COAXIAL)
Support audio sample rate .......... 32/44.1/48/88.2/96/176.4/192 kHz
FM
Tuning range
[U.S.A. and Canada models] ........................... 87.5 to 107.9 MHz
[Asia and General models] ........ 87.5/87.50 to 108.0/108.00 MHz
[U.K., Europe, Korea, Australia models] .... 87.50 to 108.00 MHz
50 dB quieting sensitivity (IHF, 1 kHz, 100% MOD.)
Mono .................................................................. 3.0 µV (20.8 dBf)
Signal to noise ratio (IHF)
Mono/stereo ............................................................... 65 dB/64 dB
Harmonic distortion (1 kHz)
Mono/stereo .................................................................. 0.5%/0.6%
Antenna input .........................................................75 W unbalanced
AM
Tuning range
[U.S.A. and Canada models] ............................... 530 to 1710 kHz
[Asia and General models] .................. 530/531 to 1710/1611 kHz
[U.K, Europe, Korea, Australia models] .............. 531 to 1611 kHz
General
Power supply
[U.S.A. and Canada models] .............................. AC 120 V, 60 Hz
[General model] ....................... AC 110-120/220-240 V, 50/60 Hz
[Korea model]...................................................... AC 220 V, 60 Hz
[Australia model] ................................................ AC 240 V, 50 Hz
[U.K. and Europe models] .................................. AC 230 V, 50 Hz
[Asia model] .......................................... AC 220-240 V, 50/60 Hz
Power consumption ................................................................. 190 W
Off mode................................................................................... 0.1 W
Standby power consumption (reference data) .......................... 0.1 W
Network Standby on
Wired ..................................................................................... 1.7 W
Wireless (Wi-Fi/Wireless Direct/Bluetooth).... 1.8 W/1.9 W/1.6 W
Maximum power consumption (1 kHz, 8 , 10% THD)
[U.K., Australia, Asia and General models]......................... 380 W
Dimensions (W H D) ................................ 435 151 392 mm
(17-1/8” 6” 15-7/16”)
Weight...................................................................... 9.8 kg (21.6 lbs)
* Specifications are subject to change without notice.
Specifications
Index
61 En
English
ADDITIONAL
INFORMATION
A
ADVANCED SETUP menu.......................................... 49
AirPlay ........................................................................... 36
AM antenna connection ................................................. 13
AM radio listening......................................................... 25
ANTENNA jacks........................................................... 13
Audio device connection ............................................... 11
Audio file format (PC/NAS).......................................... 31
Audio file format (USB) ................................................ 38
Audio Receive (Bluetooth, Setup menu) ....................... 47
Audio reception (Bluetooth) .......................................... 47
Audio Send (Bluetooth, Setup menu)............................ 47
Audio transmit (Bluetooth)............................................ 47
Auto Power Standby ...................................................... 48
Auto preset (FM radio) .................................................. 26
Auto Preset (Option menu) ............................................ 26
AutoPowerStdby (Setup menu) ..................................... 48
B
BALANCE control ........................................................ 23
Banana plug ................................................................... 12
Basic playback operation ............................................... 22
BASS control ................................................................. 23
Batteries ......................................................................... 10
Bi-wire connection......................................................... 12
Bluetooth........................................................................ 29
Bluetooth (Setup menu) ................................................. 47
Bluetooth indicator .......................................................... 7
Bluetooth Standby ......................................................... 47
Bookmark (Internet radio) ............................................. 35
C
CD jacks..................................................................... 8, 11
Clear Preset (Option menu) ........................................... 28
COAXIAL jacks ........................................................ 8, 11
Connection (Bluetooth) ................................................. 29
Connection (iPod).......................................................... 40
Connection (Network, Setup menu) .............................. 46
Connection (USB) ......................................................... 38
Connection method (Network) ...................................... 46
D
DHCP (Network, Setup menu) ...................................... 46
Digital Media Controller................................................ 46
DIMMER......................................................................... 5
DISPLAY ...................................................................... 42
DLNA ............................................................................ 31
DMC Control (Network, Setup menu) .......................... 46
E
ECO Mode (Setup menu) .............................................. 48
Error indication .............................................................. 58
F
Firmware update ................................................ 47, 50, 51
Firmware version ..................................................... 47, 50
FM antenna connection.................................................. 13
FM mode ........................................................................ 26
FM radio listening.......................................................... 25
Frequency step setting.............................................. 25, 49
Front display (Controls and functions) ............................ 7
Front panel (Controls and functions) ............................... 5
H
headphone ........................................................................ 6
I
Information (Network, Setup menu).............................. 46
Information switching (Front display) ........................... 42
INIT (ADVANCED SETUP menu) .............................. 50
Initial Volume (Setup menu).......................................... 48
Initial volume setting ..................................................... 48
Initialize ......................................................................... 50
Input selection keys........................................................ 22
INPUT selector .............................................................. 22
Internet radio (vTuner)................................................... 34
IP Address (Network, Setup menu) ............................... 46
IP address setting ........................................................... 46
iPod contents playback (AirPlay) .................................. 36
iPod contents playback (USB) ....................................... 40
iTunes contents playback (AirPlay) ............................... 36
L
LINE jacks ................................................................. 8, 11
LOUDNESS control ...................................................... 23
M
MANUAL (Wireless, Setup menu) ............................... 19
Manual network setting.................................................. 19
Max Volume (Setup menu)............................................ 48
Max volume setting........................................................ 48
Media sharing setup ....................................................... 31
MEMORY................................................................ 27, 43
Monaural (FM radio) ..................................................... 26
Mono (FM radio) ........................................................... 26
MusicCast CONTROLLER ............................................. 3
N
NAS (Network attached Storage) connection ................ 14
NAS contents playback .................................................. 31
Net Radio ....................................................................... 34
Network (Setup menu) ................................................... 46
Network cable ................................................................ 14
Network connection ................................................. 16, 21
Network connection (Setup menu) ................................ 46
Network connection (Wired) ......................................... 14
Network connection (Wireless LAN) .......... 17, 18, 19, 20
Network connection status ............................................. 21
Network information...................................................... 46
Network Name (Network, Setup menu) ........................ 47
Network Standby............................................................ 46
NEW FW Available ....................................................... 51
Index
62 En
Index
O
OPTICAL jacks ......................................................... 8, 11
OPTION ........................................................................ 44
Option menu .................................................................. 44
P
Pairing (Bluetooth) ........................................................ 29
PC connection................................................................ 14
PC contents playback .................................................... 31
Perform Update ............................................................. 47
PHONES jack.................................................................. 6
PHONO jacks ............................................................ 8, 11
Playback (AirPlay) ........................................................ 36
Playback (Bluetooth) ..................................................... 29
Playback (FM/AM radio) .............................................. 25
Playback (Internet radio) ............................................... 34
Playback (iPod) ............................................................. 40
Playback (PC/NAS)....................................................... 31
Playback (USB) ............................................................. 38
Power cable connection................................................. 15
Power saving mode........................................................ 48
Preset ............................................................................. 43
Preset (FM/AM radio) ................................................... 27
Preset (Network)............................................................ 43
Preset function ............................................................... 43
R
Rear panel (Controls and functions)................................ 8
Remote control (Controls and functions) ........................ 9
Remote control ID ......................................................... 49
REMOTE ID (ADVANCED SETUP menu) ................ 49
REPEAT (iPod) ............................................................. 41
REPEAT (PC/NAS) ...................................................... 33
REPEAT (USB) ............................................................ 39
Repeat playback (iPod).................................................. 41
Repeat playback (PC/NAS)........................................... 33
Repeat playback (USB) ................................................. 39
S
Security (Wireless Direct, Setup menu) ........................ 20
Security (Wireless, Setup menu) ................................... 19
Security Key (Wireless Direct, Setup menu) ................ 20
Security Key (Wireless, Setup menu) ........................... 19
Server............................................................................. 31
Server connection .......................................................... 14
SETUP........................................................................... 45
Setup menu .................................................................... 45
Sharing Wi-Fi connection setting (iOS device)............. 17
SHUFFLE (iPod)........................................................... 41
SHUFFLE (PC/NAS) .................................................... 33
SHUFFLE (USB) .......................................................... 39
Shuffle playback (iPod)................................................. 41
Shuffle playback (PC/NAS) .......................................... 33
Shuffle playback (USB) ................................................ 39
Signal Info. (Option menu)............................................ 44
Signal strength indicator.................................................. 7
SLEEP indicator ............................................................ 24
Sleep timer..................................................................... 24
SP IMP. (ADVANCED SETUP menu) ........................ 49
Speaker balance ............................................................. 23
Speaker cable connection............................................... 12
Speaker connection........................................................ 12
Speaker impedance ........................................................ 49
Speaker indicators............................................................ 7
Speaker selection ........................................................... 22
SPEAKERS A/B............................................................ 22
SSID (Wireless Direct, Setup menu) ............................. 20
SSID (Wireless, Setup menu) ........................................ 19
Standby (Bluetooth, Setup menu).................................. 47
Standby (Network, Setup menu).................................... 46
STATUS (Information, Setup menu)............................. 21
Stereo (FM radio)........................................................... 26
SUBWOOFER PRE OUT jacks ................................ 8, 11
System ID ...................................................................... 47
T
Tone control................................................................... 23
TREBLE control ............................................................ 23
TU (ADVANCED SETUP menu)................................. 49
Tuner frequency step ..................................................... 25
U
UPDATE (ADVANCED SETUP menu) ...................... 50
Update (Network, Setup menu) ..................................... 47
USB................................................................................ 38
USB (iPod)..................................................................... 40
USB contents playback.................................................. 38
V
VERSION (ADVANCED SETUP menu)..................... 50
Version (Network, Setup menu) .................................... 47
Vol.Interlock (Option menu) ......................................... 44
Voltage selection............................................................ 15
VOLTAGE SELECTOR ........................................... 8, 15
Volume control .............................................................. 22
Volume Interlock (Option menu) .................................. 44
Volume Trim (Option menu)......................................... 44
W
WAC .............................................................................. 17
Wi-Fi indicator................................................................. 7
Wired (Network, Setup menu)....................................... 46
Wired connection (Network) ......................................... 14
Wireless (Network, Setup menu)................................... 46
Wireless (WAC) (Wireless, Setup menu)...................... 17
Wireless Accessory Configuration ................................ 17
Wireless antenna.............................................................. 8
Wireless antenna (Wi-Fi)............................................... 14
Wireless connection (Bluetooth) ................................... 29
Wireless connection (Network) ................... 17, 18, 19, 20
Wireless Direct .............................................................. 20
WirelessDirect (Network, Setup menu)......................... 46
WPS (Wireless, Setup menu)......................................... 18
WPS push button configuration..................................... 18
i Es
Español
Español
1 Para asegurar el mejor rendimiento de este aparato, lea
atentamente este manual. Y luego guárdelo en un lugar seguro
para poder consultarlo en el futuro en caso de ser necesario.
2 Instale este sistema de sonido en un lugar bien ventilado,
fresco, seco y limpio, alejado de la luz solar directa, fuentes
de calor, vibración, polvo, humedad y/o frío. Para una
adecuada ventilación, permita que el equipo tenga el siguiente
espacio libre mínimo:
Arriba: 30 cm
Atrás: 20 cm
A los lados: 20 cm
3 Coloque este aparato lejos de otros aparatos eléctricos,
motores o transformadores, para evitar así los ruidos de
zumbido.
4 No exponga este aparato a cambios bruscos de temperaturas,
del frío al calor, ni lo coloque en lugares muy húmedos (una
habitación con deshumidificador, por ejemplo), para impedir
así que se forme condensación en su interior, lo que podría
causar una descarga eléctrica, un incendio, daños en el aparato
y/o lesiones a las personas.
5 Evite instalar este aparato en un lugar donde puedan caerle
encima objetos extraños o donde quede expuesto al goteo o a
la salpicadura de líquidos. Encima de este aparato no ponga:
Otros componentes, porque pueden causar daños y/o
decoloración en la superficie de este aparato.
Objetos con fuego (velas, por ejemplo), porque pueden
causar un incendio, daños en el aparato y/o lesiones a las
personas.
Recipientes con líquidos, porque pueden caerse y
derramar el líquido, causando descargas eléctricas al
usuario y/o dañando el aparato.
6 No tape este aparato con un periódico, mantel, cortina, etc.
para no impedir el escape del calor. Si aumenta la temperatura
en el interior del aparato, esto puede causar un incendio,
daños en el aparato y/o lesiones a las personas.
7 No enchufe este aparato a una toma de corriente hasta después
de haber terminado todas las conexiones.
8 No ponga el aparato al revés. Podría recalentarse y
posiblemente causar daños.
9 No utilice una fuerza excesiva con los conmutadores, los
controles y/o los cables.
10 Cuando desconecte el cable de la alimentación de la toma de
corriente, sujete la clavija y tire de ella; no tire del propio
cable.
11 No limpie este aparato con disolventes químicos porque
podría estropear el acabado. Utilice un paño limpio y seco
para limpiar el aparato.
12 Utilice solamente la tensión especificada en este aparato.
Utilizar el aparato con una tensión superior a la especificada
resulta peligroso y puede producir un incendio, daños en el
aparato y/o lesiones a las personas. Yamaha no se hará
responsable de ningún daño debido al uso de este aparato con
una tensión diferente de la especificada.
13 Para evitar daños debidos a rayos, durante una tormenta
eléctrica, mantenga el cable de alimentación desconectado de
la toma de corriente de la pared o de la unidad.
14 No intente modificar ni arreglar este aparato. Póngase en
contacto con el personal de servicio Yamaha cualificado
cuando necesite realizar alguna reparación. La caja no deberá
abrirse nunca por ninguna razón.
15 Cuando no piense utilizar este aparato durante mucho tiempo
(es decir, cuando se ausente de casa por vacaciones, etc.)
desconecte el cable de alimentación de la toma de corriente.
16 Asegúrese de leer la sección “Resolución de problemas” del
manual del usuario sobre los errores comunes de operación
antes de dar por concluido que su aparato está averiado.
17 Antes de trasladar este aparato, pulse A hacia abajo para
desconectar la alimentación del mismo, y luego desconecte el
cable de alimentación de CA de la toma de corriente de CA.
18 L
a condensación se formará cuando cambie de repente la
temperatura ambiental. Desconecte en este caso el cable de
alimentación de la toma de corriente y no utilice el aparato.
19 El aparato se calentará cuando la utilice durante mucho
tiempo. Desactive el sistema y, a continuación, no utilice la
unidad para dejar que se enfríe.
20 Instale este aparato cerca de la toma de CA y donde se pueda
alcanzar fácilmente la clavija de alimentación.
21 Las baterías no deberán exponerse a un calor excesivo como,
por ejemplo, el que producen los rayos del sol, el fuego y
similares. Cuando deseche las baterías, por favor cumpla las
regulaciones de su región.
22 La presión acústica excesiva de los auriculares puede causar
pérdida auditiva.
23 VOLTAGE SELECTOR (solo modelos generales)
El interruptor VOLTAGE SELECTOR del panel posterior de
este aparato deberá ponerse en la posición correspondiente a
la tensión empleada en su localidad ANTES de conectar el
aparato a la red de alimentación de CA.
Las tensiones son: CA 110-120/220–240 V, 50/60 Hz
Es necesario pegar esta etiqueta a los productos cuya cubierta
superior pueda estar caliente durante el funcionamiento.
Precaución: Lea las indicaciones siguientes antes de utilizar
este aparato.
Este aparato no se desconecta de la fuente de alimentación de CA si
está conectada a una toma de corriente, aunque la propia aparato
esté apagada con A. A este estado se le llama modo de espera. En
este estado, este aparato ha sido diseñada para que consuma un
cantidad de corriente muy pequeña.
ADVERTENCIA
PARA REDUCIR EL RIESGO DE INCENDIO O DESCARGA
ELÉCTRICA, NO EXPONGA ESTE APARATO A LA LLUVIA
NI A LA HUMEDAD.
No utilice la unidad a menos de 22 cm de personas que tengan
implantado un marcapasos o un desfribiliador.
PRECAUCIÓN: LEA LAS INDICACIONES SIGUIENTES ANTES DE UTILIZAR ESTE APARATO.
ii Es
Notas sobre el mando a distancia y las
pilas
No vierta agua ni otros líquidos sobre el mando a distancia.
No deje caer el mando a distancia al suelo.
No deje ni guarde el mando a distancia en los siguientes
entornos:
Lugares con alto grado de humedad (por ejemplo, cerca
del baño)
Lugares con altas temperaturas (por ejemplo, cerca de un
radiador o una estufa)
Lugares con temperaturas extremadamente bajas
Lugares polvorientos
Inserte las pilas según las marcas de polaridad (+ y -).
Cambie todas las pilas si nota que el rango operativo del
mando a distancia se reduce.
Si las pilas se agotan, extráigalas inmediatamente del mando a
distancia para evitar una explosión o fuga de ácido.
Si descubre que las pilas tienen fugas, descártelas
inmediatamente, con cuidado de no tocar el material vertido.
Si el material vertido entra en contacto con la piel, los ojos o
la boca, enjuáguelos inmediatamente y póngase en contacto
con un médico. Limpie a fondo el compartimento de las pilas
antes de instalar otras nuevas.
No mezcle pilas nuevas y usadas. Esto podría acortar la vida
útil de las pilas nuevas o hacer que las pilas viejas presenten
fugas.
No mezcle distintos tipos de pilas (alcalinas y de manganeso,
por ejemplo). Lea el embalaje atentamente, ya que estos tipos
distintos de pilas pueden tener la misma forma y color.
Antes de insertar pilas nuevas, limpie su compartimento.
Mantenga las pilas en una ubicación fuera del alcance de los
niños. Las pilas pueden ser peligrosas si un niño se las lleva a
la boca.
Si las pilas llevan tiempo usándose, el rango operativo
efectivo del mando a distancia se reduce considerablemente.
En este caso, cambie las pilas por otras nuevas lo antes
posible.
Si no tiene previsto utilizar la unidad durante un periodo
prolongado, extraiga las pilas de la unidad. De lo contrario, las
pilas se agotarán, lo que posiblemente provoque una fuga del
líquido de las pilas que puede dañar la unidad.
No deseche las pilas con los residuos domésticos comunes.
Deséchelas correctamente siguiendo las normativas locales.
Bluetooth
Bluetooth es una tecnología para comunicación inalámbrica
entre dispositivos dentro de un área aproximada de 10 metros
a través de la banda de frecuencia de 2,4 GHz, una banda que
se puede usar sin necesidad de licencia.
Gestión de las comunicaciones Bluetooth
La banda de 2,4 GHz utilizada por los dispositivos
compatibles con Bluetooth es una banda de radio que muchos
otros equipos también utilizan. Aunque los dispositivos
compatibles con Bluetooth utilizan una tecnología que reduce
al mínimo la influencia de otros componentes que puedan
estar usando la misma banda de radio, esta influencia
inevitablemente puede reducir la velocidad o la distancia de
las comunicaciones y, en algunos casos, interrumpir la
comunicación.
La velocidad de transferencia de la señal y la distancia a la
que es posible la comunicación varía en función de la
distancia entre los dispositivos comunicantes, la presencia de
obstáculos, las condiciones de las ondas de radio y el tipo de
equipo.
Yamaha no garantiza el funcionamiento de todas las
conexiones inalámbricas entre esta unidad y otros dispositivos
compatibles con la función Bluetooth.
1 Es
PREPARACIÓNINTRODUCCIÓN
INFORMACIÓN
ADICIONAL
MANEJO
AVANZADO
Español
MANEJO
BÁSICO
INTRODUCCIÓN
Qué puede hacer con esta unidad.............................. 2
Fuentes que pueden reproducirse en esta unidad........... 2
Control de aplicaciones útiles
(MusicCast CONTROLLER).................................... 3
Accesorios suministrados........................................... 4
Controles y funciones ................................................. 5
Panel delantero............................................................... 5
Visor delantero............................................................... 7
Panel trasero................................................................... 8
Mando a distancia .......................................................... 9
PREPARACIÓN
Conexiones................................................................. 11
Conexión de los altavoces ........................................... 12
Conexión de las antenas de FM y AM......................... 13
Conexión del cable de red............................................ 14
Preparación de un antena inalámbrica ......................... 14
Conexión del cable de alimentación ............................ 15
Conexión a red .......................................................... 16
Uso compartido del ajuste del dispositivo iOS............ 17
Uso de la configuración del botón pulsador WPS ....... 18
Ajuste la conexión de red inalámbrica manualmente ... 19
Conexión de un dispositivo móvil directamente a la
unidad (Wireless Direct).......................................... 20
Verifique el estado de conexión de red........................ 21
MANEJO BÁSICO
Reproducción ............................................................ 22
Reproducción de una fuente ........................................ 22
Uso del temporizador para dormir ............................... 24
Escucha de radio FM/AM........................................ 25
Configuración de los pasos de frecuencia ................... 25
Sintonización de FM/AM ............................................ 25
Presintonización automática (solo emisoras de FM)... 26
Presintonización manual.............................................. 27
Recuperación de una emisora presintonizada.............. 27
Borrar una emisora presintonizada .............................. 28
Reproducción de música con Bluetooth .................. 29
Conexión de un dispositivo Bluetooth (emparejado).... 29
Reproducción de contenido del dispositivo
Bluetooth ................................................................. 29
Desconexión de una conexión Bluetooth..................... 30
Reproducción de música almacenada en
servidores multimedia (PC/NAS)........................ 31
Ajuste del uso compartido de medios de archivos de
música...................................................................... 31
Reproducción de contenidos musicales del PC ........... 32
Escucha de radio de Internet................................... 34
Registro de emisoras de radio de Internet favoritas
(Bookmarks) ............................................................ 35
Reproducción de música de iPod/iTunes a
través de red (AirPlay)..........................................36
Reproducción de contenidos musicales de
iPod/iTunes.............................................................. 36
Reproducción de música almacenada en un
dispositivo de almacenamiento USB....................38
Conexión de un dispositivo de almacenamiento USB
... 38
Reproducción del contenido del dispositivo de
almacenamiento USB .............................................. 38
Reproducción de música del iPod............................40
Conexión a un iPod...................................................... 40
Reproducción de contenido del iPod ........................... 40
Cambio de la información del visor delantero .......42
Registro de la canción/emisora en reproducción
actual (función de presintonía) ............................43
Registro de una presintonía ......................................... 43
Recuperación de una presintonía ................................. 43
MANEJO AVANZADO
Configuración de ajustes de reproducción de
diferentes fuentes de reproducción
(menú Option)........................................................44
Elementos del menú Option ........................................ 44
Configuración de varias funciones (menú Setup) ...45
Elementos del menú Setup .......................................... 45
Network ....................................................................... 46
Bluetooth ..................................................................... 47
Max Volume ................................................................ 48
Initial Volume.............................................................. 48
AutoPowerStdby (Auto Power Standby)..................... 48
ECO Mode ................................................................... 48
Configuración de los ajustes del sistema
(menú ADVANCED SETUP)...............................49
Elementos del menú ADVANCED SETUP ................ 49
Cambio del ajuste de impedancia de los altavoces
(SP IMP.)................................................................. 49
Selección del ID de mando a distancia (REMOTE ID)
... 49
Cambio del ajuste de frecuencia de sintonización
FM/AM (TU)........................................................... 49
Restablecimiento de los ajustes predeterminados
(INIT) ...................................................................... 50
Actualización del firmware (UPDATE) ...................... 50
Comprobación de la versión del firmware
(VERSION) ............................................................. 50
Actualización del firmware de la unidad a través
de la red..................................................................51
INFORMACIÓN ADICIONAL
Resolución de problemas ..........................................52
Indicaciones de error que se muestran en el visor
delantero.................................................................58
Marcas comerciales...................................................59
Especificaciones.........................................................60
Índice ..........................................................................61
Contenido
“Nota” indica precauciones de uso de la unidad y las limitaciones. y indica explicaciones complementarias para mejorar el uso.
Este manual explica las operaciones con el mando a distancia suministrado.
En este manual se hace referencia a todos los “iPod” y “iPhone” como “iPod”. “iPod” se refiere a “iPod” y “iPhone”, a menos que
se especifique de otro modo.
En este manual, los dispositivos móviles iOS y Android se denominan de forma colectiva “dispositivos móviles”. El tipo
específico de dispositivo móvil se indica en las explicaciones según sea necesario.
2 Es
INTRODUCCIÓN
Esta unidad es un receptor de red compatible con una fuente de red como un servidor multimedia o un dispositivo móvil.
Admite la reproducción no solo de fuentes analógicas como un reproductor de CD, sino también de dispositivos
Bluetooth y servicios de transmisión de red.
*
Necesitará un enrutador inalámbrico de venta en el mercado (punto de acceso) si utiliza un dispositivo móvil.
1
Reproducción de la radio por Internet (pág. 34)
2 Reproducción del servicio de transmisión
(consulte el suplemento de cada servicio.)
3 Reproducción de archivos de música
guardados en su PC (pág. 31)
4 Reproducción de archivos de música
guardados en su NAS (pág. 31)
5 Reproducción de archivos de música
guardados en su iPod/iTunes con AirPlay
(pág. 36)
6 Reproducción de contenido de audio desde
dispositivos Bluetooth (pág. 29)
7 Reproducción de archivos de música
guardados en su iPod (pág. 40)
8 Reproducción de archivos de música
guardados en su dispositivo USB (pág. 38)
9 Reproducción de un componente externo
(pág. 11)
0 Escucha de radio FM/AM (pág. 25)
y
Para obtener más información sobre la conexión de dispositivos externos, consulte “Conexiones” (pág. 11).
Qué puede hacer con esta unidad
Fuentes que pueden reproducirse en esta unidad
FM/AMFM/AM
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER
DISPLAY
SELECT
PHONES
SPEAKERS
AB
MODE
Esta unidad
1 Internet
2 Servicio de transmisión
Módem
Enrutador*
3 PC
5 AirPlay (iTunes)
4 NAS
7 iPod
0
5 AirPlay (iPod)
6 Bluetooth
8 Dispositivo
USB
9 Reproductor
de CD, etc.
Dispositivo
móvil
Qué puede hacer con esta unidad
3 Es
INTRODUCCIÓN
Español
Puede utilizar y programar la unidad, o bien reproducir servicios de transmisión a través de esta unidad, instalando la
aplicación MusicCast CONTROLLER dedicada y gratuita en un dispositivo móvil. Para ver información detallada,
busque “MusicCast CONTROLLER” en el App Store o Google Play.
Capacidades de MusicCast CONTROLLER
Operaciones básicas de la unidad (encendido/espera, ajuste del volumen y selección de entrada)
Reproducción de canciones guardadas en ordenadores (servidores)
Selección de una emisora de radio de Internet
Reproducción de música guardada en dispositivos móviles
Reproducción de música en servicio de transmisión
Distribución y recepción de audio entre la unidad y otros dispositivos compatibles con MusicCast de Yamaha
Consulte Guía de instalación de MusicCast para ver información detallada.
Control de aplicaciones útiles (MusicCast CONTROLLER)
4 Es
Compruebe que se suministran los siguientes accesorios con el producto.
Accesorios suministrados
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
REPEAT
SHUFFLE
SLEEP
PHONO
B
A
SPEAKERS
OPTION
Mando a distancia
Antena de FMAntena de AM
Pilas (x2)
(AA, R6, UM-3)
Guía de instalación de MusicCast
Controles y funciones
5 Es
INTRODUCCIÓN
Español
1 A (alimentación)
Enciende y apaga (espera) la unidad.
2 Indicador STANDBY/ON
Se ilumina del siguiente modo:
Iluminación intensa: alimentación encendida
Iluminación suave: modo de espera
En modo de espera, esta unidad consume una pequeña cantidad
de energía al recibir señales infrarrojas del mando a distancia.
3 Sensor del mando a distancia
Recibe señales infrarrojas del mando a distancia.
4 DIMMER
Cambia el nivel de brillo del visor delantero. Seleccione
uno de los 5 niveles de brillo pulsando este botón de forma
repetida.
5 DISPLAY
Selecciona la información que aparece en el visor
delantero (pág. 42).
6 MODE
Ajusta el modo de recepción de banda FM en mono o
estéreo automático (pág. 26).
Cambia los modos de funcionamiento de iPod (pág. 41).
7 MEMORY
Registra la emisora de FM/AM actual como
presintonizada si TUNER está seleccionado como la
fuente de entrada (pág. 27).
Registra la canción o emisora de transmisión en
reproducción actual como presintonizada si NET o USB
(excepto iPod) están seleccionados como la fuente de
entrada (pág. 43).
8 CLEAR
Borra una emisora de FM/AM presintonizada si TUNER
está seleccionado como la fuente de entrada (pág. 28).
9 BAND
Cambia entre FM y AM (pág. 25).
0 Visor delantero
Muestra información sobre el estado operativo de esta
unidad.
A PRESET j / i
Recupera una emisora de FM/AM presintonizada
(pág. 27) o canción/emisora de transmisión (pág. 43).
B TUNING jj / ii
Selecciona la frecuencia de sintonización cuando TUNER
está seleccionado como la fuente de entrada (pág. 25).
C PURE DIRECT e indicador
Le permite escuchar una fuente con el sonido más puro
posible (pág. 22). El indicador situado encima se ilumina
y el visor delantero se apaga cuando está función está
activada.
Controles y funciones
Panel delantero
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
12 3 4 5 6 7 8 9: B CA
Nota
Controles y funciones
6 Es
D Toma PHONES
Emite audio a los auriculares para la escucha en privado.
E SPEAKERS A/B
Activa o desactiva el conjunto de altavoces conectado a
los terminales SPEAKERS A o SPEAKERS B del panel
trasero cada vez que se pulsa el botón correspondiente.
F Toma USB
Para conectar un dispositivo de almacenamiento USB
(pág. 38) o un iPod (pág. 40).
G Selector INPUT
Selecciona la fuente de entrada que se va a escuchar.
H Control BASS +/–
Aumenta o reduce la respuesta de las frecuencias bajas. La
posición central produce una respuesta plana (pág. 23).
I Control TREBLE +/
Aumenta o reduce la respuesta de frecuencias altas. La
posición central produce una respuesta plana (pág. 23).
J Control BALANCE
Ajusta el balance de salida de sonido de los altavoces
izquierdo y derecho para compensar el desequilibrio del
sonido provocado por la posición de los altavoces o por
las condiciones de escucha de la habitación (pág. 23).
K Control LOUDNESS
Conserva una gama tonal completa con cualquier nivel de
volumen para compensar la pérdida de sensibilidad del
oído humano de las gamas de frecuencia alta y baja con un
nivel de volumen bajo (pág. 23).
L SELECT/ENTER (selector táctil)
Gire el selector para seleccionar un valor numérico o
ajuste y pulse el selector para confirmar.
M RETURN
Permite volver a la indicación anterior del visor delantero.
CONNECT
Se utiliza para controlar la unidad con la aplicación
MusicCast CONTROLLER dedicada para dispositivos
móviles. Consulte Guía de instalación de MusicCast para
ver información detallada.
N Control VOLUME
Aumenta o reduce el nivel de salida del sonido.
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
NIHGED J KLMF
Controles y funciones
7 Es
INTRODUCCIÓN
Español
y
Si no se ha ajustado la conexión de red, active la alimentación (ON) para que aparezca “WAC” (Wireless Accessory Configuration) en
el panel delantero y active una búsqueda automática de dispositivos iOS. Consulte “Uso compartido del ajuste del dispositivo iOS”
(pág. 17) para ver información detallada sobre el dispositivo iOS y la conexión de red.
1 Visualización de información
Indica el estado actual (como el nombre de entrada).
Puede cambiar la información que se muestra pulsando
DISPLAY en el panel delantero (pág. 42).
2 STEREO
Se ilumina cuando la unidad está recibiendo una señal de
radio FM estéreo.
3 TUNED
Se ilumina cuando la unidad está recibiendo una señal de
radio FM/AM estéreo.
4 Indicador de intensidad de señal
Se ilumina cuando la unidad se conecta a una red
inalámbrica o funciona como un punto de acceso. La
intensidad de la señal de red inalámbrica se puede
verificar mediante el estado del indicador.
5 Indicador Bluetooth
Se ilumina cuando la unidad se conecta a un dispositivo
Bluetooth.
6 Indicadores de altavoces
“A” se ilumina cuando la salida SPEAKERS A está
activada y “B” se ilumina cuando la salida SPEAKERS B
está activada.
7 SLEEP
Se ilumina cuando el temporizador para dormir está
activado.
8 MUTE
Parpadea cuando se silencia el audio.
9 Indicador de volumen
Indica el volumen actual.
0 Indicadores del cursor
Indica qué teclas del cursor del mando a distancia están
operativas actualmente.
y
Puede cambiar el nivel de brillo del visor delantero pulsando
DIMMER en el panel delantero (pág. 5).
Visor delantero
VOL.
MUTE
TUNEDSTEREO
A
SLEEP
B
1 9
6
: :
2
3 7 854
Controles y funciones
8 Es
1 Tomas PHONO
Para conectarse a un giradiscos (pág. 11).
2 Tomas OPTICAL 1/2
Para conectarse a componentes de audio equipados con
salida digital óptica (pág. 11).
3 Terminales ANTENNA
Para conectarse a antenas de FM y AM (pág. 13).
4 Tomas COAXIAL 1/2
Para conectarse a componentes de audio equipados con
salida digital coaxial (pág. 11).
5 Terminales SPEAKERS
Se utilizan para conectar altavoces (pág. 12).
6 Toma NETWORK
Para conectarse a una red con un cable de red (pág. 14).
7 Antena inalámbrica
Para conectarse a un dispositivo de red de forma
inalámbrica (pág. 14).
8 Cable de alimentación
Para conectarse a una toma de CA (pág. 15).
9 Tomas LINE 1-3
Para conectarse a componentes de audio analógicos (
pág. 11
).
0 Tomas CD
Para conectarse a un reproductor de CD (pág. 11).
A Toma SUBWOOFER PRE OUT
Para conectarse a un altavoz de subgraves con
amplificador incorporado (pág. 11).
B Conmutador VOLTAGE SELECTOR
(Solo modelos generales)
Selecciona la posición del conmutador de acuerdo con su
tensión local (pág. 15).
Panel trasero
A
B
SPEAKERS
NETWORK
COAXIAL
OPTICAL
FM AM
75Ω
ANTENNA
SUBWOOFER
PRE OUT
PHONO
IN
1
IN
OUT
2
1
2
1
2
IN
CD
LINE
OUT
3
VO LTAGE SELECTOR
220-240V
110-120V
SIGNAL
GND
3 5 68
A
B
1 2 4 7
9 :
(Modelo general)
Controles y funciones
9 Es
INTRODUCCIÓN
Español
1 Transmisor de señales infrarrojas
Envía señales infrarrojas.
2 SPEAKERS A/B
Activa o desactiva el conjunto de altavoces conectado a los
terminales SPEAKERS A o SPEAKERS B del panel trasero de
esta unidad cuando se pulsa la tecla correspondiente.
3 Teclas selectoras de entrada
Seleccionan una fuente de entrada para su reproducción.
PHONO Tomas PHONO
COAX 1/2 Tomas COAXIAL1/2
BLUETOOTH Conexión Bluetooth
OPT 1/2 Tomas OPTICAL 1/2
CD Tomas CD
LINE 1-3 Tomas LINE 1-3
TUNER Sintonizador de FM/AM
NET Fuente de red (pulse la tecla varias veces para
seleccionar la fuente de red deseada)
USB Toma USB (en el panel delantero)
4 Teclas de radio
Permiten controlar la radio FM/AM (pág. 25).
BAND Cambia entre FM y AM.
TUNING jj/ii Selecciona la frecuencia de radio.
5 Teclas de presintonía
MEMORY Registra la emisora de FM/AM actual como
presintonizada si TUNER está seleccionado
como la fuente de entrada (pág. 27).
Registra la canción o emisora de transmisión en
reproducción actual como presintonizada si
NET o USB (excepto iPod) están seleccionados
como la fuente de entrada (pág. 43).
PRESET j/i Recupera una emisora de FM/AM
presintonizada (pág. 27) o canción/emisora de
transmisión (pág. 43).
6 Teclas de operación de menús
Teclas del cursor Seleccionan un menú o parámetro.
(B/C/D/E)
ENTER Confirma un elemento seleccionado.
RETURN Vuelve al estado anterior.
7 HOME
Se desplaza al nivel superior al seleccionar archivos de música,
carpetas, etc.
8 SETUP
Muestra el menú “Setup” (pág. 45).
9 NOW PLAYING
Muestra información sobre la música al seleccionar archivos de
música, carpetas, etc.
0 VOLUME +/-
Ajustan el volumen.
A Teclas de reproducción
Le permiten reproducir y realizar otras operaciones para fuentes
de red, dispositivos Bluetooth y dispositivos USB.
Mando a distancia
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
REPEAT
SHUFFLE
SLEEP
PHONO
B
A
SPEAKERS
OPTION
1
3
6
7
0
8
9
2
4
5
A
Controles y funciones
10 Es
B A (alimentación)
Enciende y apaga (espera) la unidad.
C SLEEP
Ajusta el temporizador para dormir (pág. 24).
D OPTION
Muestra el menú “Option” (pág. 44).
E MUTE
Silencia la salida de audio.
Instalación de las pilas
Cambie todas las pilas si se reduce el alcance operativo del
mando a distancia.
Limpie el compartimento de las pilas antes de introducir las
nuevas.
Rango operativo
El mando a distancia transmite un haz infrarrojo dirigido.
Es importante dirigir el mando a distancia directamente
hacia el sensor del mando a distancia situado en el panel
delantero de esta unidad.
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
REPEAT
SHUFFLE
SLEEP
PHONO
B
A
SPEAKERS
OPTION
B
C
D
E
Notas
2
13
11 Es
PREPARACIÓN
Español
PREPARACIÓN
No conecte esta unidad ni otros componentes a la toma principal de alimentación hasta que haya finalizado todas las
conexiones entre los componentes.
Todas las conexiones deben estar realizadas correctamente: L (izquierdo) con L, R (derecho) con R, “+” con “+” y “–”
con “–”. Si las conexiones son incorrectas, no obtendrá sonido en los altavoces. Si la polaridad de las conexiones de los
altavoces es incorrecta, el sonido no será natural y notará ausencia de graves. Consulte también el manual de
instrucciones de cada componente.
No deje que los cables pelados de los altavoces se toquen entre sí ni toquen pieza metálica alguna de esta unidad. Podría
averiar la unidad o los altavoces.
Asegúrese de utilizar cables RCA o cables ópticos para conectar componentes de audio.
y
Las tomas PHONO estén diseñadas para conectar un giradiscos con un cartucho MM.
Conecte el giradiscos al terminal GND para reducir el ruido de la señal. Sin embargo, es posible que para algunos giradiscos oiga
menos ruido sin la conexión GND.
Para evitar que la señal de audio entre en un bucle al conectar un dispositivo de grabación de audio, la señal de audio no se emite desde
las tomas LINE 2 (OUT) cuando LINE 2 está seleccionado. Asimismo, la señal de audio no se emite desde las tomas LINE 3 (OUT)
cuando LINE 3 está seleccionado.
Conexiones
PRECAUCIÓN
Solo se pueden enviar señales PCM a las tomas (OPTICAL/COAXIAL) digitales de la unidad.
Nota
A
B
SPEAKERS
NETWORK
COAXIAL
OPTICAL
FM AM
75Ω
ANTENNA
SUBWOOFER
PRE OUT
PHONO
IN
1
IN
OUT
2
1
2
1
2
IN
CD
LINE
OUT
3
SIGNAL
GND
O C
Entrada
de audio
Salida de
audio
Altavoces B
Giradiscos
Salida de
audio
Reproductor de DVD, etc.
GND
Salida de audio
(coaxial digital)
Salida de audio
(óptica digital)
Reproductor de CD, etc.
Salida de
audio
Reproductor CD
Altavoz de
subgraves
Grabadora de CD, etc.
Altavoces A
12 Es
Conexiones
Conexión de los cables de los altavoces
Los cables de los altavoces tienen dos hilos. Uno es para
conectar el terminal negativo (–) de la unidad y el altavoz
y el otro para el terminal positivo (+). Si los hilos están
codificados por colores para evitar confusiones, conecte el
hilo negro en el terminal negativo y el otro hilo en el
terminal positivo.
a
Quite aproximadamente 10 mm de aislamiento de los extremos del
cable del altavoz y retuerza los hilos expuestos con firmeza para
juntarlos.
b Afloje el terminal de los altavoces.
c Introduzca los hilos expuestos del cable en el hueco del lado
(superior derecho o inferior izquierdo) del terminal.
d Apriete el terminal.
Conexión mediante un conector tipo
banana
(solo modelo general)
Apriete la perilla e inserte el conector tipo banana en el
extremo del terminal correspondiente.
Conexión de doble cable
La conexión de doble cable separa el altavoz para graves
del rango medio combinado y la sección de agudos. Un
altavoz compatible con doble cable tiene cuatro terminales
de conexión. Estos dos conjuntos de terminales permiten
dividir el altavoz en dos secciones independientes. Con
estas conexiones, los potenciadores de frecuencias medias y
altas se conectan a un conjunto de terminales, y el
potenciador de frecuencias bajas se conecta a otro conjunto
de terminales.
Conecte el otro altavoz al otro conjunto de terminales de
la misma forma.
Cuando realice conexiones de doble cable, quite los puenteados o
los cables de los altavoces. Consulte los manuales de
instrucciones de los altavoces para obtener más información.
y
Para utilizar las conexiones de doble cable, pulse SPEAKERS A
y SPEAKERS B en el panel delantero o en el mando a distancia
para que los indicadores de altavoces (“A” y “B”) se iluminen en
el visor delantero.
Conexión de los altavoces
aa
b
b
d
d
c
c
Nota
A
B
SPEAK
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
SLEEP
PHONO
B
A
SPEAKERS
13 Es
Conexiones
PREPARACIÓN
Español
Esta unidad incluye antenas para recibir emisiones de FM y AM. En general, estas antenas deberían ofrecer una potencia
de señal suficiente. Conecte cada antena correctamente a los terminales designados.
Si tiene problemas con calidad de la recepción, instale una antena exterior. Consulte al centro de servicio o concesionario Yamaha
autorizado acerca de las antena exteriores.
Montaje de la antena de AM
suministrada
Conexión de los cables de la antena de
AM
Conexión de las antenas de FM y AM
Nota
COAXIAL
OPTICAL
FM AM
75Ω
ANTENNA
SUBWOOFER
PRE OUT
PHONO
IN
1
IN
OUT
2
1
2
1
2
IN
CD
LINE
OUT
3
SIGNAL
GND
Antena de
FM (incluida)
Antena de AM exterior
Utilice un cable recubierto de vinilo de 5 a 10
m desde una ventana hacia el exterior.
Antena de
FM exterior
La antena de AM deberá estar siempre conectada, aunque esté
conectada una antena de AM exterior.
La antena de AM deberá colocarse lejos de esta unidad.
Antena de AM (incluida)
o
14 Es
Conexiones
Conecte la unidad al enrutador con un cable de red STP disponible en el mercado (cable recto CAT-5 o superior).
Si conecta la unidad de forma inalámbrica, levante la
antena inalámbrica. Para obtener información sobre cómo
conectar la unidad a una red inalámbrica, consulte
“Conexión a red” (pág. 16).
No ejerza una fuerza excesiva en la antena inalámbrica. Podría
dañar la antena.
Conexión del cable de red
A
B
SPEAKERS
NETWORK
COAXIAL
OPTICAL
FM AM
75Ω
ANTENNA
SUBWOOFER
PRE OUT
PHONO
IN
1
IN
OUT
2
1
2
1
2
IN
CD
LINE
OUT
3
VOLTA GE SELECTOR
220-240V
110-120V
SIGNAL
GND
LAN
WAN
Network Attached Storage
(NAS)
Internet
Módem
Enrutador
Cable de red
PC
Esta unidad (parte trasera)
Dispositivo móvil
(como un iPhone)
(Modelo general)
Preparación de un antena
inalámbrica
Nota
WIRELESS
WORK
15 Es
Conexiones
PREPARACIÓN
Español
Una vez que se hayan realizado todas las conexiones,
enchufe el cable de alimentación.
Conexión del cable de
alimentación
Antes de conectar el cable de alimentación
(Solo modelos generales)
Ajuste la posición del conmutador VOLTAGE SELECTOR
según su tensión local. Las tensiones son 110–120/220–
240 V CA, 50/60 Hz.
Asegúrese de que ajusta VOLTAGE SELECTOR en la unidad
ANTES de enchufar el cable de alimentación a una toma de
CA. Un ajuste incorrecto del VOLTAGE SELECTOR puede
causar daños a esta unidad y dar lugar a un posible peligro de
incendio.
VOLTA GE SELECTOR
220-240V
110-120V
VOLTA GE SELECTOR
220-240V
110-120V
16 Es
Existen varios métodos para conectar la unidad a una red. Seleccione un método de conexión en función de su entorno.
Cierto software de seguridad instalado en el equipo o la configuración del firewall de los dispositivos de red (como un enrutador),
podrían impedir el acceso de la unidad a los dispositivos de red o a Internet. En tales casos, configure adecuadamente el software de
seguridad o el firewall.
Todos los servidores deben estar conectados a la misma subred que la unidad.
Para usar el servicio por Internet, es muy recomendable disponer de una conexión de banda ancha.
Conexión con la aplicación MusicCast CONTROLLER
Consulte Guía de instalación de MusicCast para ver información detallada.
Conexión con el enrutador por cable
Conexión con un enrutador inalámbrico (punto de acceso)
Conéctese a la red con el método especificado a continuación que se corresponda con su entorno.
Conexión sin un enrutador por cable o enrutador inalámbrico (punto de acceso)
Cuando la unidad se conecta a la red con Wireless Direct, no se puede conectar a ningún otro enrutador inalámbrico (punto de acceso).
Para reproducir contenido desde Internet, conecte esta unidad a una red con un enrutador por cable o enrutador inalámbrico (punto de
acceso).
Conexión a red
Notas
Al reproducir una fuente de audio de alta resolución a través de la red, se recomienda realizar la conexión con un enrutador por cable
para que la reproducción sea estable.
Nota
Conexión con la función del servidor DHCP del
enrutador
Puede conectarse a la red
simplemente realizando una
conexión por cable (pág. 14)
Conexión con el ajuste de Wi-Fi del dispositivo
iOS (iPhone / iPod touch)
Comparta el ajuste de Wi-Fi del
dispositivo iOS (pág. 17)
Conexión con la configuración del botón
pulsador WPS en el enrutador inalámbrico (o
punto de acceso)
Utilice la configuración del botón
pulsador WPS (pág. 18)
Conexión con un enrutador inalámbrico (punto de
acceso) sin configuración del botón pulsador
WPS
Ajuste la conexión de red
manualmente (pág. 19)
Conexión inalámbrica con un dispositivo móvil
(Wireless Direct)
Conéctese de forma inalámbrica
con Wireless Direct (pág. 20)
17 Es
Conexión a red
PREPARACIÓN
Español
Puede configurar con facilidad una conexión inalámbrica
aplicando los ajustes de conexión en dispositivos OS
(iPhone/iPod touch).
Antes de continuar, confirme que su dispositivo iOS está
conectado a un enrutador inalámbrico (punto de acceso).
1 Pulse A para encender esta unidad.
2 Pulse SETUP.
3 Utilice las teclas del cursor (B / C) para
seleccionar “Network” y pulse ENTER.
y
Para volver al estado anterior, pulse RETURN.
4 Utilice las teclas del cursor (B / C) para
seleccionar “Connection” y pulse ENTER.
5 Utilice las teclas del cursor (B / C) para
seleccionar “Wireless” y pulse ENTER.
6 Utilice las teclas del cursor (B / C) para
seleccionar “Share Setting” y pulse ENTER.
7 Utilice las teclas del cursor (B / C) para
seleccionar el método de conexión deseado
y pulse ENTER.
Están disponibles los siguientes métodos de conexión.
Al seleccionar “Wireless (WAC)” como el método de conexión,
se inicializan todos los ajustes de red.
Uso compartido inalámbrico del ajuste
del dispositivo iOS
Si selecciona “Wireless (WAC)” como el método de
conexión, realice la operación de uso compartido del
ajuste de red en su dispositivo iOS. (El procedimiento
siguiente es un ejemplo de configuración para iOS 8.)
1 En el dispositivo iOS, seleccione la unidad
como el altavoz AirPlay en la pantalla Wi-Fi.
2 Compruebe la red seleccionada actualmente
y pulse “Next”.
Uso compartido del ajuste del
dispositivo iOS
Si no se ha ajustado la conexión de red, al activar esta
unidad, “WAC” (Wireless Accessory Configuration)
aparece en el visor delantero y la configuración del
dispositivo iOS puede ser compartida.
Para compartir el ajuste del dispositivo iOS, realice la
operación de uso compartido del ajuste de red en su
dispositivo iOS.
R-N602 XXXXXX
WAC
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
WPS
WIRELESS
Wireless
(WAC)
Puede aplicar los ajustes de conexión en el
dispositivo iOS a la unidad con una conexión
inalámbrica. Para ver información detallada, consulte
“Uso compartido inalámbrico del ajuste del
dispositivo iOS”. (Necesita un dispositivo iOS con
iOS 7 o posterior.)
USB
Cable
Puede aplicar los ajustes de conexión en el
dispositivo iOS a la unidad con un cable USB. Para
ver información detallada, consulte “Uso compartido
del ajuste del dispositivo iOS con un cable USB”.
(Necesita un dispositivo iOS con iOS 5 o posterior.)
Nota
Wireless(WAC)
SHARE
18 Es
Conexión a red
Una vez finalizado el proceso de uso compartido, la
unidad se conecta automáticamente a la red (punto de
acceso) seleccionada.
Una vez finalizado el ajuste, verifique si la unidad
está conectada a una red inalámbrica (pág. 21).
Uso compartido del ajuste del
dispositivo iOS con un cable USB
Si selecciona “USB Cable” como el método de conexión,
siga el procedimiento siguiente para compartir el ajuste
del dispositivo iOS con la unidad.
1 Conecte el dispositivo iOS a la toma USB y
desactive el bloqueo de pantalla en el
dispositivo iOS.
2 Pulse ENTER.
3 Toque “Permitir” en el mensaje que aparece
en el dispositivo iOS.
Cuando el proceso de conexión finalice, “Completed”
aparecerá en el visor delantero.
Una vez finalizado el ajuste, verifique si la unidad
está conectada a una red inalámbrica (pág. 21).
4 Para salir del menú, pulse SETUP.
Puede configurar con facilidad una conexión inalámbrica
con una pulsación del botón WPS.
Esta configuración no funciona si el método de seguridad de su
enrutador inalámbrico (punto de acceso) es WEP. En tal caso,
utilice otro método de conexión.
1 Pulse A para encender esta unidad.
2 Pulse SETUP.
3 Utilice las teclas del cursor (B / C) para
seleccionar “Network” y pulse ENTER.
y
Para volver al estado anterior, pulse RETURN.
4 Utilice las teclas del cursor (B / C) para
seleccionar “Connection” y pulse ENTER.
5 Utilice las teclas del cursor (B / C) para
seleccionar “Wireless” y pulse ENTER.
6 Pulse ENTER dos veces.
“Connecting” aparece en el visor delantero.
7 Pulse el botón WPS en el enrutador
inalámbrico (punto de acceso).
Cuando el proceso de conexión finalice, “Completed”
aparecerá en el visor delantero. Una vez finalizado el
ajuste, verifique si la unidad está conectada a una red
inalámbrica (pág. 21).
Si aparece “Not connected”, repita el procedimiento
desde el paso 1 o intente otro método de conexión.
8 Para salir del menú, pulse SETUP.
Uso de la configuración del botón
pulsador WPS
Nota
MEMORY CLEAR
BASSINPUT
5V
1A
TREBLE
DIMMER MODE
DISPLAY
PHONES
SPEAKERS
AB
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
Acerca de WPS
WPS (Wi-Fi Protected Setup) es el estándar establecido por la
Wi-Fi Alliance, que permite la configuración sencilla de una
red doméstica inalámbrica.
WPS
WIRELESS
19 Es
Conexión a red
PREPARACIÓN
Español
Antes de realizar el siguiente procedimiento, compruebe
el método de seguridad y la contraseña en el enrutador
inalámbrico (punto de acceso).
1 Pulse A para encender esta unidad.
2 Pulse SETUP.
3 Utilice las teclas del cursor (B / C) para
seleccionar “Network” y pulse ENTER.
y
Para volver al estado anterior, pulse RETURN.
4 Utilice las teclas del cursor (B / C) para
seleccionar “Connection” y pulse ENTER.
5 Utilice las teclas del cursor (B / C) para
seleccionar “Wireless” y pulse ENTER.
6 Utilice las teclas del cursor (B / C) para
seleccionar “Manual Setting” y pulse ENTER.
7 Utilice las teclas del cursor (B / C) para
seleccionar “SSID” y pulse ENTER.
8 Utilice las teclas del cursor para introducir el
SSID en el enrutador inalámbrico (punto de
acceso) y pulse RETURN para volver al
estado anterior.
Utilice las teclas del cursor (D/E) para mover la
posición de edición y las teclas del cursor (B/C) para
seleccionar un carácter.
9 Utilice las teclas del cursor (B / C) para
seleccionar “Security” y pulse ENTER.
10 Utilice las teclas del cursor (D / E) para
seleccionar el método de seguridad deseado
y pulse RETURN.
Ajustes
None, WEP, WPA2-PSK (AES), Mixed Mode
Si selecciona “None”, la conexión de puede ser no segura debido
a que la comunicación no está cifrada.
11 Utilice las teclas del cursor (B / C) para
seleccionar “Security Key” y pulse ENTER.
12 Utilice las teclas del cursor para introducir la
contraseña en el enrutador inalámbrico
(punto de acceso) y pulse RETURN para
volver al estado anterior.
Si selecciona “WEP” en el paso 10, introduzca una
cadena de 5 a 13 caracteres o entre 10 y 26 dígitos
hexadecimales.
Si selecciona “WPA2-PSK (AES)” o “Mixed Mode”
en el paso 10, introduzca una cadena de 8 a 63
caracteres o 64 dígitos hexadecimales.
Utilice las teclas del cursor (D/E) para mover la
posición de edición y las teclas del cursor (B/C) para
seleccionar un carácter.
Puede introducir o eliminar un carácter pulsando
PRESET i (introducir) o PRESET j (eliminar).
13 Utilice las teclas del cursor (B / C) para
seleccionar “Connect[ENTER]” y pulse
ENTER para guardar el ajuste.
Si aparece “ERROR”, compruebe el SSID y la
contraseña en el enrutador inalámbrico (punto de
acceso) y repita el procedimiento desde el paso 7.
Si no aparece “ERROR”, la conexión se ha realizado
correctamente. Verifique si la unidad está conectada a
una red inalámbrica (pág. 21).
14 Para salir del menú, pulse SETUP.
Ajuste la conexión de red
inalámbrica manualmente
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
SSID
MANUAL
SSID
Nota
WPA2-PSK(AES)
SECURITY
KEY
20 Es
Conexión a red
Mediante Wireless Direct, esta unidad puede funcionar
como un punto de acceso de red inalámbrica al que
pueden conectarse directamente los dispositivos móviles.
Cuando la unidad se conecta a la red con Wireless Direct, no se
puede conectar a ningún otro enrutador inalámbrico (punto de
acceso). Para reproducir contenido desde Internet, conecte esta
unidad a una red con un enrutador por cable o enrutador
inalámbrico (punto de acceso).
1 Pulse A para encender esta unidad.
2 Pulse SETUP.
3 Utilice las teclas del cursor (B / C) para
seleccionar “Network” y pulse ENTER.
y
Para volver al estado anterior, pulse RETURN.
4 Utilice las teclas del cursor (B / C) para
seleccionar “Connection” y pulse ENTER.
5 Utilice las teclas del cursor (B / C) para
seleccionar “WirelesDirect” y pulse ENTER.
6 Pulse ENTER para comprobar el SSID en
esta unidad y pulse RETURN para volver al
estado anterior.
7 Utilice las teclas del cursor (B / C) para
seleccionar “Security” y pulse ENTER.
8 Utilice las teclas del cursor (D / E) para
seleccionar el método de seguridad deseado
y pulse RETURN.
Ajustes
None, WPA2-PSK (AES)
Si selecciona “None”, la conexión de puede ser no segura debido
a que la comunicación no está cifrada.
9 Utilice las teclas del cursor (B / C) para
seleccionar “Security Key” y pulse ENTER.
10 Utilice las teclas del cursor para introducir la
contraseña en esta unidad y pulse RETURN
para volver al estado anterior.
Introduzca una cadena de 8 a 63 caracteres o 64
dígitos hexadecimales.
Utilice las teclas del cursor (D / E) para mover la
posición de edición y las teclas del cursor (B / C)
para seleccionar un carácter.
Puede introducir o eliminar un carácter pulsando
PRESET i (introducir) o PRESET j (eliminar).
11 Utilice las teclas del cursor (B / C) para
seleccionar “Connect[Enter]” y pulse ENTER
para guardar el ajuste.
La información de SSID y contraseña es necesaria
para la configuración de un dispositivo móvil.
Al seleccionar el “SSID” en el paso 6, puede
comprobar el SSID configurado en esta unidad. El
SSID de esta unidad se puede cambiar con las teclas
del cursor (B / C / D / E).
12 Configure los ajustes de Wi-Fi de un
dispositivo móvil.
Para ver información detallada sobre los ajustes del
dispositivo móvil, consulte el manual de
instrucciones del dispositivo móvil.
(1) Active la función Wi-Fi en el dispositivo móvil.
(2) Seleccione el SSID de esta unidad de la lista de
puntos de acceso disponibles.
(3) Cuando se le solicite una contraseña, introduzca
la contraseña mostrada en el paso 10.
Si aparece “ERROR”, compruebe la contraseña en
esta unidad y repita el paso 12.
Si no aparece “ERROR”, la conexión se ha realizado
correctamente. Verifique si la unidad está conectada a
una red inalámbrica (pág. 21).
13 Para salir del menú, pulse SETUP.
Conexión de un dispositivo móvil
directamente a la unidad
(Wireless Direct)
Nota
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
SSID
W DIRECT
WPA2-PSK(AES)
W DIRECT
Nota
KEY
21 Es
Conexión a red
PREPARACIÓN
Español
Realice el siguiente procedimiento para verificar la
conexión de la unidad a una red.
1 Pulse SETUP.
2 Utilice las teclas del cursor (B / C) para
seleccionar “Network” y pulse ENTER.
y
Para volver al estado anterior, pulse RETURN.
3 Utilice las teclas del cursor (B / C) para
seleccionar “Information” y pulse ENTER.
4 Utilice las teclas del cursor (B / C) para
seleccionar “STATUS”.
Si aparece “Connect”, la unidad está conectada a una
red. Si aparece “Disconnect”, restablezca la
conexión.
5 Para salir del menú, pulse SETUP.
Verifique el estado de conexión de
red
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
Connect
STATUS
22 Es
MANEJO BÁSICO
1 Pulse A (alimentación) para encender esta
unidad.
2 Gire el selector INPUT del panel delantero (o
pulse una de las teclas de selección de
entradas del mando a distancia) para
seleccionar la fuente de entrada que quiera
escuchar.
3 Pulse SPEAKERS A o SPEAKERS B en el
panel delantero o en el mando a distancia
para seleccionar los altavoces A o B.
Cuando los altavoces A o B estén activados, en el
visor delantero aparecerá “A” o “B” respectivamente
(pág. 7).
Si uno de los conjuntos de altavoces está conectado mediante
conexiones de doble cable, o si ambos conjuntos se están
utilizando a la vez (A y B), asegúrese de que el visor delantero
muestra “A” y “B”.
Cuando utilice auriculares, desconecte los altavoces.
4 Reproduzca la fuente.
5 Gire el control VOLUME en el panel delantero
(o pulse VOLUME +/– en el mando a
distancia) para ajustar el nivel de salida de
sonido.
y
Puede ajustar la calidad tonal utilizando los controles BASS,
TREBLE, BALANCE y LOUDNESS o el conmutador PURE
DIRECT del panel delantero.
6 Cuando finalice la operación, pulse A
(alimentación) en el panel delantero para
apagar la alimentación.
Al pulsar A (alimentación) en el mando a distancia,
esta unidad se ajusta en el modo de espera.
Sonido de alta fidelidad puro
(Pure Direct)
Cuando el conmutador PURE DIRECT está activado,
envía las señales de entrada desde sus fuentes de audio de
modo que las señales omiten los controles BASS,
TREBLE, BALANCE y LOUDNESS, lo que elimina
cualquier alteración de las señales de audio y crea el
sonido más puro posible.
El indicador PURE DIRECT se ilumina y el visor
delantero se apaga después de unos segundos.
Cuando el conmutador PURE DIRECT está activado, el visor
delantero se apaga.
Los controles BASS, TREBLE, BALANCE y LOUDNESS no
funcionan mientras el conmutador PURE DIRECT está activado.
Reproducción
Reproducción de una fuente
Notas
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
TUNING
BAND
SLEEP
PHONO
B
A
SPEAKERS
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
OPTION
Notas
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
23 Es
Reproducción
Español
MANEJO
BÁSICO
Ajuste de los controles BASS y TREBLE
Los controles BASS y TREBLE ajustan la respuesta de las
frecuencias altas y bajas.
La posición central produce una respuesta plana.
Control BASS
Cuando note que no hay suficientes graves (sonido de
frecuencia baja), gire en el sentido de las agujas del reloj
para aumentarlos. Cuando note que hay demasiados
graves, gire en el sentido contrario al de las agujas del
reloj para suprimirlos.
Rango de control: De –10 dB a +10 dB (20 Hz)
Control TREBLE
Cuando note que no hay suficientes agudos (sonido de
frecuencia alta), gire en el sentido de las agujas del reloj
para aumentarlos. Cuando note que hay demasiados
agudos, gire en el sentido contrario al de las agujas del
reloj para suprimirlos.
Rango de control: De –10 dB a +10 dB (20 kHz)
Ajuste del control BALANCE
El control BALANCE ajusta el balance de salida de
sonido de los altavoces izquierdo y derecho para
compensar el desequilibrio del sonido provocado por la
posición de los altavoces o por las condiciones de escucha
de la habitación.
Ajuste del control LOUDNESS
Conserve una gama tonal completa con cualquier nivel de
volumen para compensar la pérdida de sensibilidad del
oído humano de las gamas de frecuencia alta y baja con un
volumen bajo.
Si el conmutador PURE DIRECT se activa con el control
LOUDNESS definido a un determinado nivel, las señales
de entrada omiten el control LOUDNESS, lo que provoca
un aumento repentino del nivel de salida del sonido. Para
evitar lesiones en sus oídos o daños en los altavoces,
asegúrese de pulsar el conmutador PURE DIRECT
después de bajar el nivel de salida del sonido o después de
comprobar que el control LOUDNESS se ha ajustado
correctamente.
1 Ajuste el control LOUDNESS en la posición
FLAT.
2 Gire el control VOLUME en el panel delantero
(o pulse VOLUME +/– en el mando a
distancia) para ajustar el nivel de salida del
sonido en el nivel de escucha más alto con el
que desea escuchar.
3 Gire el control LOUDNESS hasta obtener el
volumen deseado.
y
Después de ajustar el control LOUDNESS, podrá escuchar la
música con su nivel de volumen preferido. Si el efecto del ajuste
del control LOUDNESS es demasiado intenso o débil, reajuste el
control LOUDNESS.
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
PRECAUCIÓN
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
OPTION
24 Es
Reproducción
Utilice esta característica para ajustar automáticamente la
unidad al modo de espera una vez transcurrido un tiempo
definido. El temporizador para dormir resulta útil cuando
se va a dormir mientras la unidad está reproduciendo o
grabando una fuente.
El temporizador para dormir solo se puede ajustar con el mando a
distancia.
1 Pulse SLEEP repetidamente para ajustar el
tiempo que transcurrirá antes de que la
unidad pase al modo de espera.
Cada vez que pulse SLEEP, el visor delantero
cambiará como se muestra a continuación.
El indicador SLEEP parpadea mientras se ajusta el
tiempo del temporizador para dormir.
Si el temporizador para dormir está ajustado, el
indicador SLEEP del visor delantero se ilumina.
y
Para desactivar el temporizador para dormir, seleccione “Sleep
Off”.
El ajuste del temporizador para dormir también se puede
cancelar pulsando A (alimentación) para ajustar esta unidad al
modo de espera.
Uso del temporizador para dormir
Nota
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
LINE 2 LINE 3
SLEEP
PHONO
B
A
SPEAKERS
A
SLEEP
VOL.
A
Sleep 120min.
SLEEP
25 Es
MANEJO
BÁSICO
Español
En fábrica, el ajuste de paso de frecuencia se establece en
50 kHz para FM y 9 kHz para AM. Según la región o el
país donde escuche la radio, establezca los pasos de
frecuencia en 100 kHz para FM y 10 kHz para AM.
1 Apague la unidad.
2 Mientras mantiene pulsado RETURN en el
panel frontal, pulse A (alimentación).
3 Gire SELECT/ENTER para seleccionar “TU”.
4 Pulse SELECT/ENTER para seleccionar
“FM100/AM10”.
5 Pulse A (alimentación) para apagar y volver a
encender la unidad.
1 Pulse TUNER para seleccionar “TUNER”
como fuente de entrada.
2 Pulse BAND repetidamente para seleccionar
la banda de recepción (FM o AM).
3 Mantenga pulsado TUNING jj / ii durante
más de 1 segundo para comenzar la
sintonización.
Pulse ii para sintonizar una frecuencia más alta.
Pulse jj para sintonizar una frecuencia más baja.
La frecuencia de la emisora recibida se muestra en el
visor delantero.
Si se recibe una emisión, el indicador “TUNED” del
visor delantero se iluminará. Si se recibe una emisión
en estéreo, el indicador “STEREO” también se
iluminará.
y
Si las señales de la emisora son débiles, la búsqueda de
sintonización no se detiene en la emisora deseada.
Si la señal de recepción de una emisora FM no es estable, puede
mejorar si se cambia a monoaural.
Escucha de radio FM/AM
Configuración de los pasos de
frecuencia
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
TU••••FM50/AM9
Sintonización de FM/AM
TUNING jj / ii
TUNER
BAND
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SLEEP
PHONO
B
A
SPEAKERS
VOL.
TUNEDSTEREO
A
FM 98.50MHz
26 Es
Escucha de radio FM/AM
Mejora de la recepción de FM (modo FM)
Si la señal de la emisora es débil y la calidad del sonido no
es buena, ajuste el modo de recepción de la banda de FM a
monoaural para mejorar la recepción.
1 Pulse MODE repetidamente para seleccionar
“Stereo” (modo estéreo automático) o
“Mono” (modo mono) cuando en la unidad
se sintonice una emisora de radio FM.
Si se selecciona Mono, las emisiones de FM se
escucharán con sonido mono.
El indicador STEREO en el panel delantero se ilumina mientras
se escucha una emisora en modo estéreo.
Puede utilizar la función de presintonización automática
para registrar automáticamente emisoras de FM como
presintonías. Esta función permite a la unidad sintonizar
automáticamente emisoras de FM con una señal intensa y
registrar hasta 40 emisoras en orden. Así podrá recuperar
fácilmente cualquier emisora presintonizada
seleccionando su número de presintonía.
Si una emisora se registra en un número de presintonía que ya
tenga registrada una emisora, la emisora anterior se
sobrescribirá.
Si la emisora que desea registrar tiene una señal débil, pruebe a
utilizar el método de presintonización manual.
y
Las emisoras de FM registradas como presintonías utilizando la
característica de presintonización automática se escucharán en
estéreo.
1 Pulse TUNER para seleccionar “TUNER”
como fuente de entrada.
2 Pulse OPTION en el mando a distancia.
Aparecerá el menú “Option” (pág. 44).
3 Pulse B / C para seleccionar “Auto Preset” y,
a continuación, pulse ENTER.
La unidad comenzará el barrido de la banda de FM
unos 5 segundos más tarde a partir de la frecuencia
más baja.
Para comenzar el barrido inmediatamente, mantenga
pulsado ENTER.
y
Antes de iniciar el barrido, puede especificar el primer número
de presintonía que se utilizará pulsando PRESET j / i o la tecla
del cursor (B/C) en el mando a distancia.
Para cancelar el barrido, pulse BAND o RETURN.
Una vez completado el barrido, “FINISH” aparece en
pantalla y después se regresa al estado original.
Nota
Presintonización automática
(solo emisoras de FM)
Notas
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
LINE 1
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
PRESET j / i
RETURN
OPTION
TUNER
BAND
ENTER
VOL.
A
Auto Preset
OPTION
VOL.
A
01:FM 87.50MHz
READY
27 Es
Escucha de radio FM/AM
Español
MANEJO
BÁSICO
Seleccione una emisora manualmente y regístrela en un
número de preajuste. Así podrá recuperar fácilmente
cualquier emisora presintonizada seleccionando su
número de presintonía.
1 Siga las indicaciones de “Sintonización de
FM/AM” (pág. 25) para sintonizar la emisora
de radio deseada.
2
Mantenga pulsado MEMORY más de 2
segundos.
La primera vez que registre una emisora, la emisora
seleccionada se registrará en el número de preajuste
“01”. Posteriormente, cada emisora de radio que
seleccione se registrará en el siguiente número vacío
(no utilizado) tras el número registrado más
recientemente.
y
Para seleccionar un número de presintonía para el registro, pulse
MEMORY una vez tras sintonizar la emisora, pulse PRESET j / i
para seleccionar un número de presintonía y, a continuación,
vuelva a pulsar MEMORY.
Puede recuperar emisoras presintonizadas registradas
utilizando la presintonización automática o manual de
emisoras.
1 Pulse TUNER para seleccionar “TUNER”
como fuente de entrada.
2 Pulse PRESET j / i para seleccionar un
número de presintonía.
y
Se omitirán los números de presintonía sin estaciones
registradas.
“No Presets” aparecerá en pantalla si no hay emisoras
registradas.
Presintonización manual
NET USB
TUNER
PRESET
TUNING
BAND
MEMORY
ENTER
PRESET j / i
MEMORY
VOL.
A
01:FM 98.50MHz
MEMORY
TUNEDSTEREO
VOL.
A
02:Empty
9850
TUNEDSTEREO
Recuperación de una emisora
presintonizada
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SLEEP
PHONO
B
A
SPEAKERS
TUNER
PRESET j / i
28 Es
Escucha de radio FM/AM
Borre las emisoras de radio registradas en los números de
preajuste.
1 Pulse TUNER para seleccionar “TUNER”
como fuente de entrada.
2 Pulse OPTION.
3 Utilice las teclas del cursor para seleccionar
“Clear Preset” y pulse ENTER.
4 Utilice las teclas del cursor (B / C) para
seleccionar la emisora presintonizada que se
vaya a borrar y pulse ENTER.
Si la emisora presintonizada se ha borrado, aparece
“Cleared” y, a continuación, se muestra el siguiente
número de presintonía en uso.
5 Repita el paso 4 hasta que se hayan borrado
todas las emisoras preajustadas.
6 Para salir del menú “Option”, pulse OPTION.
y
Puede borrar una emisora presintonizada desde el panel
delantero.
(1) Pulse CLEAR en el panel delantero.
(2) Pulse PRESET D/E para seleccionar la emisora
presintonizada que desea borrar.
(3) Pulse SELECT/ENTER o CLEAR para borrar la emisora
presintonizada.
Borrar una emisora presintonizada
LINE 1
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
OPTION
ENTER
TUNER
VOL.
Clear Preset
OPTION
VOL.
A
01:FM 98.50MHz
CLEAR
TUNEDSTEREO
VOL.
01:Cleard
CLEAR
A
29 Es
MANEJO
BÁSICO
Español
En la unidad puede reproducir los archivos de música
guardados en un dispositivo Bluetooth (como dispositivos
móviles).
Consulte también el manual de instrucciones de su
dispositivo Bluetooth.
Para utilizar la función Bluetooth, ajuste “Bluetooth” (pág. 47)
en el menú “Setup” en “On”.
Puede que la unidad no detecte un dispositivo Bluetooth o que
algunas funciones no sean compatibles, dependiendo del
modelo.
y
Puede transmitir audio a auriculares o altavoces Bluetooth con la
aplicación MusicCast CONTROLLER. Para transmitir audio,
ajuste “Audio Send” (pág. 47) en el menú “Configuración” en
“On”. La salida de audio solo se puede seleccionar desde la
aplicación MusicCast CONTROLLER.
Cuando conecte un dispositivo Bluetooth a la unidad por
primera vez, será necesario realizar la operación de
emparejado. El emparejado es una operación para registrar
con antelación dispositivos Bluetooth entre sí. Una vez
finalizado el emparejado, las siguientes conexiones serán
fáciles incluso después de haber desconectado la conexión
Bluetooth.
1 Pulse BLUETOOTH para seleccionar
“Bluetooth” como fuente de entrada.
Si ya hay otro dispositivo Bluetooth conectado,
desconecte la conexión Bluetooth antes de realizar la
operación de emparejado.
2 Active la función Bluetooth del dispositivo
Bluetooth.
3 En el dispositivo Bluetooth, seleccione el
nombre de modelo de la unidad de la lista de
dispositivos disponibles.
Después de haber finalizado el emparejado y si la
unidad está conectada al dispositivo Bluetooth, en el
visor delantero aparece “Connected” y el indicador
Bluetooth se iluminará.
y
Si se necesita una contraseña, escriba el número “0000”.
Complete el procedimiento de emparejado antes de 5 minutos.
Si no se encuentran dispositivos Bluetooth, aparecerá “Not
found”.
Conecte un dispositivo Bluetooth emparejado y comience
la reproducción. Compruebe con antelación lo siguiente:
El emparejado se había finalizado.
La función Bluetooth del dispositivo Bluetooth está
activada.
1 Pulse BLUETOOTH para seleccionar
“Bluetooth” como fuente de entrada.
y
Si la unidad detecta el dispositivo Bluetooth conectado
anteriormente, la unidad se conecta automáticamente al
dispositivo Bluetooth después del paso 1. Para establecer otra
conexión Bluetooth, finalice primero la conexión Bluetooth
actual.
Reproducción de música con Bluetooth
Notas
Conexión de un dispositivo
Bluetooth (emparejado)
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
SLEEP
PHONO
B
A
SPEAKERS
Reproducción de contenido del
dispositivo Bluetooth
Connected
BLUETOOTH
A
VOL.
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
SLEEP
PHONO
B
A
SPEAKERS
REPEAT
SHUFFLE
30 Es
Reproducción de música con Bluetooth
2 Utilice el dispositivo Bluetooth para
establecer una conexión Bluetooth.
Seleccione el nombre de modelo de la unidad de la
lista de dispositivos Bluetooth de su dispositivo.
Una vez establecida la conexión, el indicador
Bluetooth del visor delantero se iluminará.
y
Si no puede conectarse al dispositivo Bluetooth, vuelva a realizar
el emparejado.
3 Utilice el dispositivo Bluetooth para
reproducir música.
y
Puede usar las teclas de reproducción del mando a distancia para
controlar la reproducción.
Siga los procedimientos indicados a continuación para
desconectar una conexión Bluetooth.
Desactive la función Bluetooth del dispositivo
Bluetooth.
Mantenga pulsado BLUETOOTH en el mando a
distancia durante al menos 3 segundos.
Seleccione “Disconnect” en “Audio Receive” (pág. 47)
en el menú “Setup” y, a continuación, pulse ENTER.
Seleccione una fuente de entrada distinta de
“Bluetooth” en la unidad.
Desconexión de una conexión
Bluetooth
31 Es
MANEJO
BÁSICO
Español
En la unidad puede reproducir los archivos de música almacenados en un PC o NAS (Network Attached Storage)
compatible con DLNA.
Para utilizar esta función, la unidad y el PC/NAS deben estar conectados al mismo enrutador (pág. 14). Puede comprobar si los
parámetros de red (por ejemplo, la dirección IP) están correctamente asignados a la unidad en “Information” (pág. 46) en el menú
“Setup”.
La unidad admite la reproducción de archivos WAV (solo formato PCM), AIFF, MP3, WMA, MPEG-4 AAC, FLAC, ALAC y DSD.
La unidad es compatible con unas frecuencias de muestreo de hasta 192 kHz para los archivos WAV, AIFF y FLAC, de 96 kHz para
los archivos ALAC y de 48 kHz para los demás archivos.
La unidad es compatible con archivos DSD de 2,8 MHz/5,6 MHz (1 bit).
No se puede reproducir contenido de Digital Rights Management (DRM).
Para reproducir archivos de música, el software de servidor instalado en el PC/NAS debe ser compatible con los formatos de archivos
de música que desea reproducir.
y
Puede conectar hasta 16 servidores multimedia a esta unidad.
Para reproducir archivos de música en el ordenador con
esta unidad, debe aplicar el ajuste de uso compartido de
medios entre la unidad y el ordenador (Windows Media
Player 11 o una versión más reciente). En este caso, se
utiliza como ejemplo el ajuste con Windows Media Player
en Windows 7.
Si se utiliza Windows Media Player 12
1 Inicie Windows Media Player 12 en el PC.
2 Seleccione “Transmitir” y luego “Activar la
transmisión por secuencias de multimedia”.
Aparecerá la ventana de panel de control del PC.
3 Haga clic en “Activar la transmisión por
secuencias de multimedia”.
Reproducción de música almacenada en servidores multimedia (PC/NAS)
Notas
PC
NAS
Esta unidad
Ajuste del uso compartido de
medios de archivos de música
32 Es
Reproducción de música almacenada en servidores multimedia (PC/NAS)
4 Seleccione “Permitido” en la lista
desplegable situada junto al nombre de
modelo de la unidad.
5 Haga clic en “Aceptar” para salir.
Si se utiliza Windows Media Player 11
1 Inicie Windows Media Player 11 en el PC.
2 Seleccione “Biblioteca” y luego “Uso
compartido de multimedia”.
3 Active la casilla “Compartir mi multimedia
con”, seleccione el icono de la unidad y haga
clic en “Permitir”.
4 Haga clic en “Aceptar” para salir.
Si se utiliza un PC o NAS con otro
software de servidor DLNA instalado
Consulte el manual de instrucciones del dispositivo o
software y configure el uso compartido de medios.
Realice el procedimiento siguiente para controlar el
contenido de música del PC e iniciar la reproducción.
Se mostrará “_” (guión bajo) para los caracteres que no admite la
unidad.
1 Pulse NET varias veces para seleccionar
“Server” como fuente de entrada.
2 Utilice las teclas del cursor (B / C) para
seleccionar un servidor de música y pulse
ENTER.
3 Utilice las teclas del cursor para seleccionar
un elemento y pulse ENTER.
Si hay una canción seleccionada, empieza la
reproducción y se muestra la información de
reproducción.
Reproducción de contenidos
musicales del PC
Nota
NET USB
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
REPEAT
SHUFFLE
OPTION
RETURN
OPTION
NOW PLAYING
HOME
ENTER
NET
NAS A
SERVER
A
Song A
SERVER
A
33 Es
Reproducción de música almacenada en servidores multimedia (PC/NAS)
Español
MANEJO
BÁSICO
y
Si en el PC se está reproduciendo un archivo de música
seleccionado desde la unidad, se muestra la información de
reproducción.
Puede registrar la canción en reproducción actual como una
presintonía (pág. 43).
Si pulsa DISPLAY en el panel delantero repetidamente, puede
alternar la información de reproducción en el visor delantero
(pág. 42).
Utilice las siguientes teclas del mando a distancia para
controlar la reproducción.
y
También puede usar un Digital Media Controller (DMC)
compatible con DLNA para controlar la reproducción. Para
obtener más información, consulte “DMC Control” (pág. 46).
Ajustes de repetición/reproducción
aleatoria
Puede configurar la reproducción aleatoria o la repetición
del contenido de música del PC.
1 Si la fuente de entrada es “SERVER”, pulse
REPEAT o SHUFFLE repetidamente en la
tecla de reproducción para seleccionar el
método de reproducción.
Teclas Función
Teclas del cursor
Seleccione un archivo de música
o carpeta.
ENTER
Inicia la reproducción si se pulsa
con un contenido seleccionado.
Baja un nivel si se pulsa con una
carpeta seleccionada.
RETURN
Sube un nivel.
Teclas de
reproducción
p/ e
Detiene/reanuda la reproducción.
s
Detiene la reproducción.
b / w
Salta hacia delante o atrás.
(con la tecla pulsada) Busca hacia
delante o atrás.
f / a
HOME
Muestra el directorio raíz del
servidor de música.
NOW PLAYING
Muestra información sobre la
canción que se está
reproduciendo.
Teclas de
reproducción
Ajuste Función
REPEAT
Off Desactiva la función de repetición.
One
Reproduce la canción actual
repetidamente.
All
Reproduce todas las canciones del
álbum (carpeta) actual repetidamente.
SHUFFLE
Off
Desactiva la función de reproducción
aleatoria.
On
Reproduce las canciones del álbum
(carpeta) actual en orden aleatorio.
34 Es
También puede escuchar emisoras de radio de Internet de todo el mundo.
Para usar esta función, la unidad debe estar conectada a Internet
(pág. 14). Puede comprobar si los parámetros de red (por
ejemplo, la dirección IP) esn correctamente asignados a la
unidad en “Information” (pág. 46) en el menú “Setup”.
Es posible que no pueda recibir algunas emisoras de radio de
Internet.
La unidad utiliza el servicio de base de datos de emisoras de
radio de Internet vTuner.
Este servicio puede suspenderse sin previo aviso.
1 Pulse NET varias veces para seleccionar
“Net Radio” como fuente de entrada.
La lista de emisoras aparece en el visor delantero.
2 Utilice las teclas del cursor para seleccionar
un elemento y pulse ENTER.
Si hay una emisora de radio de Internet seleccionada,
empieza la reproducción y se muestra la información
de reproducción.
Utilice las siguientes teclas del mando a distancia
para controlar la reproducción.
y
Puede registrar la emisora en reproducción actual como una
presintonía (pág. 43).
Si pulsa DISPLAY en el panel delantero repetidamente, puede
alternar la información de reproducción en el visor delantero
(pág. 42).
Es posible que alguna información no esté disponible
dependiendo de la emisora.
Escucha de radio de Internet
Notas
LINE 1
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
NOW PLAYING
HOME
ENTER
NET
Bookmarks
NET RADIO
A
Teclas Función
Teclas del cursor
Seleccione la emisora de radio de
Internet o la categoría, como por
ejemplo el género.
ENTER
Inicia la reproducción si se pulsa
con una emisora de radio de
Internet seleccionada. Baja un
nivel si se pulsa con una categoría
seleccionada.
RETURN
Sube un nivel.
Teclas de
reproducción
s
Detiene la reproducción.
HOME
Muestra las categorías superiores
si se pulsa durante la
reproducción.
NOW PLAYING
Muestra la información de
reproducción para la emisora de
radio de Internet.
JazzST
NET RADIO
A
35 Es
Escucha de radio de Internet
Español
MANEJO
BÁSICO
Al registrar sus emisoras de radio de Internet favoritas en
“Bookmarks”, puede acceder a ellas rápidamente desde la
carpeta “Bookmarks” en el visor delantero.
1 Seleccione cualquiera de las emisoras de
radio de Internet en la unidad.
Esta operación es necesaria para registrar la emisora
de radio por primera vez.
2 Compruebe el ID de vTuner de la unidad.
Puede encontrar el ID de vTuner (dirección MAC de
la unidad) en “Information” (pág. 46) en el menú
“Setup”.
3 Acceda al sitio web de vTuner
(http://yradio.vtuner.com/) con el navegador
de Internet del PC e introduzca el vTuner ID.
y
Para utilizar esta función, debe crear su cuenta personal. Cree la
cuenta utilizando su dirección de correo electrónico.
4 Registre sus emisoras de radio favoritas.
Haga clic en el icono “Add” (+) situado junto al
nombre de la emisora.
y
Para eliminar la emisora de la carpeta “Bookmarks”, seleccione
“Bookmarks” en la pantalla de inicio y haga clic en el icono
“Remove” (–) situado junto al nombre de la emisora.
Registro de emisoras de radio de
Internet favoritas (Bookmarks)
36 Es
La función AirPlay le permite reproducirsica de iPod/
iTunes en la unidad a través de la red.
Para utilizar esta función, la unidad y el PC o el iPod deben estar
conectados al mismo enrutador (pág. 14). Puede comprobar si los
parámetros de red (por ejemplo, la dirección IP) están
correctamente asignados a la unidad en “Information” (pág. 46)
en el menú “Setup”.
Realice el procedimiento siguiente para reproducir el
contenido de música de iPod/iTunes en la unidad.
1 Encienda la unidad e inicie iTunes en el PC o
muestre la pantalla de reproducción en el
iPod.
Si iPod/iTunes reconoce la unidad, aparece el icono
AirPlay ( ).
y
Para los iPod con iOS 7/8, el icono AirPlay se muestra en Control
Center. Para acceder a Control Center, deslice el dedo hacia arriba
desde la parte inferior de la pantalla.
Si el icono no aparece, compruebe si la unidad y el PC/iPod están
correctamente conectados al enrutador.
2 En iPod/iTunes, haga clic en (toque) el icono
AirPlay y seleccione la unidad (nombre de
red de la unidad) como dispositivo de salida
de audio.
3 Seleccione una canción e inicie la
reproducción.
La unidad selecciona automáticamente “AirPlay” como
fuente de entrada e inicia la reproducción. La información
de reproducción aparece en el visor delantero.
y
Si pulsa DISPLAY en el panel delantero repetidamente, puede
alternar la información de reproducción en el visor delantero
(pág. 42).
Puede encender automáticamente la unidad cuando comience la
reproducción en iTunes o el iPod ajustando “Standby (Network
Standby)” (pág. 46) en el menú “Setup” en “On”.
Puede editar el nombre de red (el nombre de la unidad en la red)
mostrado en iPod/iTunes en “Network Name” (pág. 47) en el
menú “Setup”.
Puede ajustar el volumen de la unidad desde iPod/iTunes
durante la reproducción.
Cuando se utilizan los controles de iPod/iTunes para
ajustar el volumen, el volumen puede estar más alto de lo
normal. Esto podría causar daños en la unidad o en los
altavoces. Si el volumen aumenta repentinamente durante
la reproducción, detenga inmediatamente la reproducción
en iPod/iTunes.
Reproducción de música de iPod/iTunes a través de red (AirPlay)
Nota
AirPlay funciona con los iPhone, iPad y iPod touch con iOS
4.3.3 o posterior, Mac con OS X Mountain Lion o posterior, y
Mac y PC con iTunes 10.2.2 o posterior.
(en agosto de 2015)
Reproducción de contenidos musicales
de iPod/iTunes
Nota
PRECAUCIÓN
37 Es
Reproducción de música de iPod/iTunes a través de red (AirPlay)
Español
MANEJO
BÁSICO
Utilice las siguientes teclas del mando a distancia para
controlar la reproducción.
Para controlar la reproducción de iTunes con el mando a distancia
de la unidad tiene que configurar las preferencias de iTunes para
activar de antemano el control de iTunes desde altavoces remotos.
Teclas Funciones
Teclas de
reproducción
p/ e
Detiene/reanuda la reproducción.
s
Detiene la reproducción.
b / w
Salta hacia delante o atrás.
f / a
REPEAT Cambia los ajustes de repetición.
SHUFFLE
Cambia los ajustes de
reproducción aleatoria.
Nota
38 Es
En la unidad puede reproducir los archivos de música almacenados en un dispositivo de almacenamiento USB. Consulte
los manuales de instrucciones del dispositivo de almacenamiento USB para obtener más información.
La unidad admite dispositivos de almacenamiento masivo USB (por ejemplo, memorias flash o reproductores de audio portátiles)
utilizando el formato FAT16 o FAT32.
La unidad admite archivos WAV (solo formato PCM), AIFF, MP3, WMA, MPEG-4 AAC, FLAC, ALAC y DSD.
La unidad es compatible con una frecuencia de muestreo de hasta 192 kHz para los archivos WAV, AIFF y FLAC, de 96 kHz para los
archivos ALAC y de 48 kHz para los demás archivos.
La unidad es compatible con archivos DSD de 2,8 MHz/5,6 MHz (1 bit).
No conecte dispositivos que no sean de almacenamiento masivo USB (como cargadores USB o nodos USB), PC, lectores de tarjetas,
un HDD externo, etc.
Los dispositivos USB con cifrado no se pueden utilizar.
No se puede reproducir contenido de Digital Rights Management (DRM).
Algunas funciones pueden no ser compatibles, dependiendo del modelo o del fabricante del dispositivo de almacenamiento USB.
1 Conecte el dispositivo de almacenamiento
USB a la toma USB.
y
Si el dispositivo de almacenamiento USB contiene muchos
archivos, podrían tardar un rato en cargarse. En ese caso, en el
visor delantero se muestra “Loading...”.
Desconecte el dispositivo de almacenamiento USB de la toma
USB cuando no lo esté utilizando.
Detenga la reproducción del dispositivo de almacenamiento
USB antes de proceder a desconectarlo de la toma USB.
No puede conectar el PC a la toma USB de la unidad.
Realice el procedimiento siguiente para controlar el
dispositivo de almacenamiento USB e iniciar la
reproducción.
Se mostrará “_” (guión bajo) para los caracteres que no admite la
unidad.
1
Pulse USB para seleccionar “USB” como
fuente de entrada.
Reproducción de música almacenada en un dispositivo de
almacenamiento USB
Notas
Conexión de un dispositivo de
almacenamiento USB
Notas
BASSINPUT
5V
1A
PHONES
SPEAKERS
AB
Connected
USB
A
VOL.
Reproducción del contenido del
dispositivo de almacenamiento USB
Nota
LINE 1
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
REPEAT
SHUFFLE
OPTION
RETURN
USB
NOW PLAYING
HOME
ENTER
Bluse
USB
A
VOL.
39 Es
Reproducción de música almacenada en un dispositivo de almacenamiento USB
Español
MANEJO
BÁSICO
2 Utilice las teclas del cursor para seleccionar
un elemento y pulse ENTER.
Si hay una canción seleccionada, empieza la
reproducción y se muestra la información de
reproducción.
y
Puede registrar la canción en reproducción actual como una
presintonía (pág. 43).
Si pulsa DISPLAY en el panel delantero repetidamente, puede
alternar la información de reproducción en el visor delantero
(pág. 42).
Utilice las siguientes teclas del mando a distancia para
controlar la reproducción.
Ajustes de repetición/reproducción
aleatoria
Puede configurar los ajustes de reproducción aleatoria o
repetición para la reproducción de contenido del
dispositivo de almacenamiento USB.
1 Si la fuente de entrada es “USB,” pulse
REPEAT o SHUFFLE repetidamente en las
teclas de reproducción para seleccionar el
método de reproducción.
Teclas Función
Teclas del cursor
Seleccione un archivo de música
o carpeta.
ENTER
Inicia la reproducción si se pulsa
con un archivo de música
seleccionado. Baja un nivel si se
pulsa con una carpeta
seleccionada.
RETURN
Sube un nivel.
Teclas de
reproducción
p/ e
Detiene/reanuda la reproducción.
s
Detiene la reproducción.
b / w
Salta hacia delante o atrás.
f / a
HOME
Muestra el directorio raíz del
dispositivo USB.
NOW PLAYING
Muestra información sobre la
canción que se está
reproduciendo.
Track #3
USB
A
Teclas de
reproducción
Ajuste Función
REPEAT
Off Desactiva la función de repetición.
One
Reproduce la canción actual
repetidamente.
All
Reproduce todas las canciones del
álbum (carpeta) actual repetidamente.
SHUFFLE
Off
Desactiva la función de reproducción
aleatoria.
On
Reproduce las canciones del álbum
(carpeta) actual en orden aleatorio.
40 Es
Mediante un cable USB suministrado con el iPod, puede escuchar música del iPod en la unidad.
Puede que la unidad no detecte un iPod o que algunas funciones
no sean compatibles, dependiendo del modelo o la versión de
software del iPod.
Conecte el iPod a la unidad con el cable USB
suministrado con el iPod.
1 Conecte el cable USB al iPod.
2 Conecte el cable USB a la toma USB.
y
Si “Standby (Network Standby)” (pág. 46) en el menú “Setup”
está ajustado en “Off”, el iPod continuará cargándose durante un
máximo de 4 horas si la unidad pasa al modo de espera durante la
carga del iPod.
Desconecte el iPod de la toma USB cuando no lo esté utilizando.
Realice el procedimiento siguiente para controlar el
contenido del iPod e iniciar la reproducción.
Se mostrará “_” (guión bajo) para los caracteres que no admite la
unidad.
1 Pulse USB para seleccionar “USB” como
fuente de entrada.
2 Utilice las teclas del cursor para seleccionar
un elemento y pulse ENTER.
Si hay una canción seleccionada, empieza la
reproducción y se muestra la información de
reproducción.
y
Si pulsa DISPLAY en el panel delantero repetidamente, puede
alternar la información de reproducción en el visor delantero
(pág. 42).
Para usar el iPod manualmente y seleccionar un contenido o
controlar la reproducción, cambie al modo de reproducción
sencilla (pág. 41).
Reproducción de música del iPod
Nota
Made for
iPod touch (2nd, 3rd, 4th and 5th generation)
iPod nano (2nd, 3rd, 4th, 5th, 6th and 7th generation)
iPhone 6, iPhone 6 Plus, iPhone 5s, iPhone 5c, iPhone 5,
iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G
(en agosto de 2015)
Conexión a un iPod
Nota
BASSINPUT
5V
1A
DIMMER MO
DISPLAY
PHONES
SPEAKERS
AB
Connected
USB
A
VOL.
Reproducción de contenido del
iPod
Nota
LINE 1
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
REPEAT
SHUFFLE
OPTION
RETURN
USB
NOW PLAYING
HOME
ENTER
Music
USB
A
VOL.
Track #1
USB
A
VOL.
41 Es
Reproducción de música del iPod
Español
MANEJO
BÁSICO
Utilice las siguientes teclas del mando a distancia para
controlar la reproducción.
Control del propio iPod o el mando a
distancia (reproducción sencilla)
1 Pulse MODE en el panel delantero para
cambiar al modo de reproducción sencilla.
En el modo de reproducción sencilla, en el visor
delantero solo se muestra el nombre de entrada. Si
confirma la información de reproducción, consulte la
pantalla del iPod.
y
Si desea salir del modo de reproducción sencilla, vuelva a pulsar
MODE.
2 Utilice el propio iPod o el mando a distancia
para iniciar la reproducción.
Utilice las siguientes teclas del mando a distancia
para controlar la reproducción en el modo de
reproducción sencilla.
Ajustes de repetición/reproducción
aleatoria
Puede configurar los ajustes de reproducción aleatoria y
repetición del iPod.
1 Si la fuente de entrada es “USB,” pulse
REPEAT o SHUFFLE repetidamente en las
teclas de reproducción para seleccionar el
método de reproducción.
y
El funcionamiento o la visualización de la reproducción aleatoria
o la repetición pueden variar en función del tipo o la versión de
software del iPod usado.
Teclas Función
Teclas del cursor
Seleccione un archivo de música,
un álbum o un género.
ENTER
Inicia la reproducción si se pulsa
con un archivo de música
seleccionado. Baja un nivel si se
pulsa con un álbum o género
seleccionado.
RETURN
Sube un nivel.
Teclas de
reproducción
p/ e
Detiene/reanuda la reproducción.
s
Detiene la reproducción.
b / w
Salta hacia delante o atrás.
(con la tecla pulsada) Busca hacia
delante o atrás.
f / a
HOME
Muestra el menú superior del
iPod.
NOW PLAYING
Muestra información sobre la
canción que se está
reproduciendo.
Teclas de
funcionamiento del
mando a distancia
Función
Teclas del cursor
Selecciona un elemento.
ENTER
Confirma la selección.
RETURN
Vuelve al estado anterior.
Teclas de
reproducción
p/ e
Inicia la reproducción o detiene la
reproducción temporalmente.
s
Detiene la reproducción.
b / w
Salta hacia delante o atrás.
(con la tecla pulsada) Busca hacia
delante o atrás.
f / a
Teclas de
reproducción
Ajuste Función
REPEAT
Off Desactiva la función de repetición.
One
Reproduce la canción actual
repetidamente.
All
Reproduce todas las canciones
repetidamente.
SHUFFLE
Off
Desactiva la función de reproducción
aleatoria.
Songs
Reproduce canciones en orden
aleatorio.
Albums
Reproduce álbumes en orden
aleatorio.
42 Es
Al seleccionar una fuente de red o USB como la fuente de entrada, puede alternar la información de reproducción en el
visor delantero.
1 Pulse DISPLAY.
Cada vez que pulse la tecla, cambia el elemento que
se muestra.
Unos 3 segundos después, aparece la información
correspondiente para el elemento que se muestra.
Cambio de la información del visor delantero
Fuente de entrada
Elemento
Bluetooth
Server
AirPlay
USB (incluye iPod)
Track (título de la canción), Artist (nombre
del artista), Album (nombre del álbum),
Time
Net Radio
Track (título de la canción), Album
(nombre del álbum), Time, Station (nombre
de la emisora)
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
Track
INFO
A
Track #1
SERVER
A
43 Es
MANEJO
BÁSICO
Español
Al seleccionar fuentes de red y USB como la fuente de entrada, puede registrar la canción o emisora de transmisión en
reproducción actual como una presintonía hasta un máximo de 40.
Así podrá recuperar fácilmente cualquier canción/emisora presintonizada seleccionando su número de presintonía.
Las fuentes de entrada siguientes se pueden ajustar como presintonías.
Server, Net Radio, USB (excepto iPod) y servicios de transmisión.
1 Reproduzca una canción o emisora de
transmisión que desee registrar.
2 Mantenga pulsado MEMORY más de 3
segundos.
La primera vez que registre una canción/emisora, la
canción/emisora seleccionada se registrará en el
número de presintonía “01”. Posteriormente, cada
canción/emisora que seleccione se registrará en el
siguiente número de presintonía vacío (no utilizado)
tras el número registrado más recientemente.
y
Para seleccionar un número de presintonía para el registro, pulse
PRESET j/i o las teclas del cursor (D/E).
3 Vuelva a pulsar MEMORY para registrar la
presintonía.
1 Seleccione la fuente de entrada de la que
desea recuperar la presintonía.
2 Pulse PRESET j / i para seleccionar un
número de presintonía.
3 Pulse ENTER para recuperar la presintonía.
Registro de la canción/emisora en reproducción actual
(función de presintonía)
Registro de una presintonía
NET USB
TUNER
PRESET
TUNING
BAND
MEMORY
ENTER
PRESET j / i
MEMORY
ENTER
01:Empty
MEMORY
A
Recuperación de una presintonía
44 Es
MANEJO AVANZADO
Puede configurar los ajustes de reproducción de diferentes fuentes de reproducción. Este menú permite configurar con
facilidad ajustes durante la reproducción.
1 Pulse OPTION.
2 Utilice las teclas del cursor para seleccionar
un elemento y pulse ENTER.
y
Para volver al estado anterior durante operaciones del menú,
pulse RETURN.
3 Utilice las teclas del cursor (D / E) para
seleccionar un ajuste.
4 Para salir del menú, pulse OPTION.
y
Los elementos disponibles varían según la fuente de entrada
seleccionada.
Volume Trim
Corrige las diferencias de volumen entre las fuentes de
entrada. Si le molestan las diferencias de volumen al
cambiar de fuente de entrada, use esta función para que no
se produzcan.
y
Este ajuste se aplica a cada fuente de entrada por separado.
Gama de ajustes
De -10,0 dB a 0,0 dB a +10,0 dB (incrementos de 0,5 dB)
Predeterminado
0,0 dB
Signal Info.
Muestra información sobre la señal de audio.
Opciones
y
Para alternar la información en el visor delantero, pulse las teclas
del cursor (B / C) repetidamente.
Vol.Interlock (Volume interlock)
Activa/desactiva los controles de volumen desde iTunes/
iPod a través de AirPlay.
Ajustes
Configuración de ajustes de reproducción de diferentes fuentes
de reproducción (menú Option)
Elementos del menú Option
Elemento Función
Página
Volume Trim
Corrige las diferencias de volumen
entre las fuentes de entrada.
44
Signal Info.
Muestra información sobre la señal de
audio.
44
Auto Preset
Registra automáticamente las emisoras
de FM con señales intensas como
preajustes.
26
Clear Preset
Borra las emisoras de radio registradas
en los números de preajuste.
28
Vol.Interlock
(Volume interlock)
Activa/desactiva los controles de
volumen desde iTunes/iPod a través de
AirPlay.
44
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
OPTION
ENTER
VOL.
A
Volume Trim
OPTION
FORMAT Formato de audio de la señal de entrada
SAMPLING
Número de muestras por segundo de la señal
digital de entrada
Off
Desactiva los controles de volumen desde iTunes/
iPod.
Ltd
(predeter-
minado)
Activa los controles de volumen desde iTunes/
iPod en el rango limitado (de -80,0 dB a -20,0 dB
y silencio).
Full
Activa los controles de volumen desde iTunes/
iPod en el rango completo (-80,0 dB a +16,5 dB y
silencio).
45 Es
Español
MANEJO
AVANZADO
Puede configurar las distintas funciones de la unidad.
1 Pulse SETUP.
2 Utilice las teclas del cursor (B / C) para
seleccionar un menú.
3 Pulse ENTER.
4 Utilice las teclas del cursor (D / E) para
seleccionar un ajuste y pulse ENTER.
y
Para volver al estado anterior durante operaciones del menú,
pulse RETURN.
5 Salga del menú pulsando SETUP.
Configuración de varias funciones (menú Setup)
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
Network
SETUP
A
Max Volume
SETUP
A
+16.5dB
MAX VOL
A
Elementos del menú Setup
Elemento de menú Función
Página
Network
Connection
Selecciona el método de
conexión de red.
46
Information
Muestra la información de
red sobre la unidad.
46
IP Address
Configura los parámetros de
red (como, por ejemplo, la
dirección IP).
46
DMC
Control
Selecciona si se permite que
un Digital Media Controller
(DMC) compatible con
DLNA controle la
reproducción.
46
Standby
(Network
Standby)
Selecciona si se activa/
desactiva la función que
enciende la unidad mediante
comandos desde otros
dispositivos de red.
46
Network
Name
Edita el nombre de red (el
nombre de la unidad en la
red) mostrado en otros
dispositivos de red.
47
Update
(Network
Update)
Actualiza el firmware a
través de la red.
47
Bluetooth
On/Off
Activa o desactiva las
funciones de Bluetooth.
47
Standby
(Bluetooth
Standby)
Selecciona si se activa/
desactiva la función que
enciende la unidad desde
dispositivos Bluetooth
(Bluetooth en espera).
47
Audio
Receive
Recibe ajustes de audio
desde el dispositivo
Bluetooth.
47
Audio Send
Transmite audio desde la
unidad a los auriculares o
altavoces Bluetooth.
47
Max Volume
Ajusta el volumen máximo
para evitar un volumen
excesivamente alto.
48
Initial Volume
Ajusta el volumen inicial
para cuando se encienda
este receptor.
48
AutoPowerStdby
(Auto Power Standby)
Ajusta el tiempo de la
función de espera
automática.
48
ECO Mode
Activa/desactiva el modo
eco (modo de ahorro
energético).
48
46 Es
Configuración de varias funciones (menú Setup)
Configura los ajustes de la red.
Connection
Selecciona el método de conexión de red.
Information
Muestra la información de red sobre la unidad.
IP Address
Configura los parámetros de red (como, por ejemplo, la
dirección IP).
DHCP
Selecciona si se utiliza un servidor DHCP.
Ajustes manuales de red
1 Ajuste “DHCP” enOff”.
2 Utilice las teclas del cursor (B / C) para
seleccionar un tipo de parámetro.
3 Utilice las teclas del cursor (D / E) para
seleccionar la posición de edición.
(Ejemplo: ajuste de la dirección IP)
Utilice las teclas del cursor (D / E) para alternar entre
segmentos (Address1, Address2...) de la dirección.
4 Utilice las teclas del cursor (B / C) para
cambiar un valor.
5 Para salir del menú, pulse SETUP.
DMC Control
Selecciona si se permite que un Digital Media Controller
(DMC) compatible con DLNA controle la reproducción.
y
Un Digital Media Controller (DMC) es un dispositivo que puede
controlar otros dispositivos de red a través de ésta. Cuando esta
función está activada, se puede controlar la reproducción de la unidad
desde los DMC (como Windows Media Player 12) en la misma red.
Standby (Network Standby)
Selecciona si la unidad se puede encender desde otros
dispositivos de red (red en espera).
Network
Wired
Seleccione esta opción cuando desee conectar
la unidad a una red con un cable de red que
adquiera en el mercado (pág. 16).
Wireless
Seleccione esta opción cuando desee conectar la
unidad a una red a través de un enrutador
inalámbrico o punto de acceso (pág. 17, 18, 19).
WirelessDirect
Seleccione esta opción cuando desee conectar
un dispositivo móvil directamente a la unidad.
Para ver información detallada sobre los
ajustes, consulte “Conexión de un dispositivo
móvil directamente a la unidad (Wireless
Direct)” (pág. 20).
Extend
Muestra el método de conexión de la red
MusicCast.
NEW FW
Available
Aparece si hay disponible una actualización
del firmware de esta unidad (pág. 51).
STATUS Estado de conexión de la red.
MC NET
Estado de la red MusicCast. Si aparece
“Ready”, puede utilizar la aplicación
MusicCast CONTROLLER.
MAC
Muestra la dirección MAC de la unidad. La
dirección MAC variará en función del método
de conexión (conexión LAN por cable o
conexión LAN/Wireless Direct inalámbrica).
SSID
(Cuando se utiliza la conexión LAN
inalámbrica o Wireless Direct). El SSID de
esta unidad en la red inalámbrica.
IP Dirección IP
SUBNET Máscara de red secundaria
GATEWAY Dirección IP de la puerta predeterminada
DNS P Dirección IP del servidor DNS primario
DNS S Dirección IP del servidor DNS secundario
VTUNER ID de la radio de Internet (vTuner)
Off
No utiliza un servidor DHCP. Configure
manualmente los parámetros de red. Para conocer
más detalles, consulte “Ajustes manuales de red”.
On
(predeter-
minado)
Utiliza un servidor DHCP para obtener
automáticamente los parámetros de red de la
unidad (como la dirección IP).
IP Especifica una dirección IP.
SUBNET Especifica una máscara de red secundaria.
GATEWAY
Especifica la dirección IP de la puerta
predeterminada.
DNS P
Especifica la dirección IP del servidor DNS primario.
DNS S
Especifica la dirección IP del servidor DNS
secundario.
Disable No permite que un DMC controle la reproducción.
Enable
(predeter-
minado)
Permite que un DMC controle la reproducción.
Off Desactiva la función de red en espera.
On
Activa la función de red en espera. (La unidad
consume más potencia que cuando está
seleccionado “Off”.)
Auto
(predeter-
minado)
Activa la función de red en espera. La unidad se
ajusta en el modo de ahorro energético cuando se
desconecta de la red.
Address1•••192
NETWORK
A
47 Es
Configuración de varias funciones (menú Setup)
Español
MANEJO
AVANZADO
Network Name
Edita el nombre de red (el nombre de la unidad en la red)
mostrado en otros dispositivos de red.
1 Seleccione “Network Name”.
2 Pulse ENTER dos veces para acceder a la
pantalla de edición de nombre.
3 Utilice las teclas del cursor (D / E) para
mover la posición de edición y las teclas del
cursor (B / C) para seleccionar un carácter.
Puede introducir o eliminar un carácter pulsando
PRESET i (introducir) o PRESET j (eliminar).
4 Para confirmar el nombre nuevo, pulse
ENTER.
5 Para salir del menú, pulse SETUP.
Update (Network Update)
Actualiza el firmware a través de la red.
Configura los ajustes de Bluetooth.
On/Off
Activa o desactiva la función de Bluetooth (pág. 29).
Standby (Bluetooth Standby)
Selecciona si se activa/desactiva la función que enciende
la unidad desde dispositivos Bluetooth (Bluetooth en
espera). Si esta función se ajusta en “On”, la unidad se
enciende automáticamente cuando se realiza una
operación de conexión en el dispositivo Bluetooth.
y
Este ajuste no está disponible cuando “Standby (Network
Standby)” (pág. 46) está ajustado en “Off”.
Audio Receive
Recibe ajustes de audio desde el dispositivo Bluetooth.
Audio Send
Transmite audio desde la unidad a los auriculares o
altavoces Bluetooth.
Perform Update
Inicia el proceso para actualizar el firmware
de la unidad. Para obtener más información,
consulte “Actualización del firmware de la
unidad a través de la red” (pág. 51).
Version
Muestra la versión de firmware instalada en
la unidad.
ID Muestra el número de ID del sistema.
Network Name
NETWORK
A
R-N602 XXXXXX
NAME
A
R-N602 XXXXXX
NAME
A
Bluetooth
Off Desactiva la función de Bluetooth.
On
(predeterminado)
Activa la función de Bluetooth. Justo después
de seleccionar “On”, la salida de la fuente de
red se pone en pausa.
Off Desactiva la función de Bluetooth en espera.
On
(predeterminado)
Activa la función de Bluetooth en espera. (La
unidad consume más potencia que cuando
está seleccionado “Off”.)
Disconnect
Desconecta el dispositivo Bluetooth
conectado. Para desconectar el dispositivo
Bluetooth, pulse ENTER en el mando a
distancia.
Off
(predeterminado)
No se puede transmitir el audio.
On
Activa la transmisión de audio. Especifique
los ajustes de transmisión de audio con la
aplicación MusicCast CONTROLLER
dedicada para dispositivos móviles.
48 Es
Configuración de varias funciones (menú Setup)
Ajusta el volumen máximo para evitar un volumen
excesivamente alto.
Gama de ajustes
De -30 dB a +15,0 dB / +16,5 dB (paso de 5 dB)
Predeterminado
+16,5 dB
Ajusta el volumen inicial cuando se encienda el receptor.
Gama de ajustes
Off, Mute, de -80,0 dB a +16,5 dB (paso de 0,5 dB)
Predeterminado
Off
Activa/desactiva la función de espera automática. Si no
utiliza la unidad durante el tiempo especificado, ésta
entrará automáticamente en modo de espera.
y
Justo antes de que la unidad pase al modo de espera, aparece
“AutoPowerStdby” en el visor delantero y comienza la cuenta
atrás.
Activa/desactiva el modo eco (de ahorro energético).
Cuando el modo eco está activado, puede reducir el
consumo de la unidad.
El nuevo ajuste tendrá efecto después de reiniciar la
unidad. Asegúrese de pulsar ENTER para reiniciar la
unidad tras seleccionar un ajuste.
Cuando “ECO Mode” está ajustado en “On”, el visor frontal
puede oscurecerse.
Max Volume
Initial Volume
AutoPowerStdby
(Auto Power Standby)
Off
(predeterminado)
No pone la unidad en modo de espera
automáticamente.
On
Ajusta la unidad automáticamente en el modo
de espera. Con NET, BLUETOOTH o USB
seleccionado como la fuente de entrada, la
unidad cambiará al modo de espera si la fuente
de seleccionada no se reproduce durante 20
minutos.
Para todas las fuentes de entrada, la unidad
cambiará al modo de espera si no se utiliza
durante 8 horas.
ECO Mode
Off
(predeterminado)
Desactiva el modo eco.
On Activa el modo eco.
Nota
49 Es
Español
MANEJO
AVANZADO
Configurar los ajustes de sistema de la unidad mientras visualiza el visor delantero.
1 Apague la unidad.
2
Mientras mantiene pulsado RETURN en el
panel delantero, pulse
A (alimentación).
3 Gire SELECT/ENTER para seleccionar un
elemento.
4 Pulse SELECT/ENTER para seleccionar un
ajuste.
5 Pulse A (alimentación) para apagar y volver a
encender la unidad.
Los nuevos ajustes tendrán efecto.
Cambie los ajustes de impedancia de los altavoces de la
unidad según la impedancia de los altavoces conectados.
Ajustes
Si se utilizan varios receptores en la misma habitación,
ajuste el ID de mando a distancia de esta unidad en ID1 (y
ajuste el otro receptor en un valor distinto de ID1). Podrá
evitar las interferencias de otros mandos a distancia.
Ajustes
ID1, AUTO (predeterminado)
Cambie el ajuste de frecuencia de sintonización de FM/
AM de la unidad en función de su país o región.
Ajustes
Configuración de los ajustes del sistema
(menú ADVANCED SETUP)
Elementos del menú ADVANCED
SETUP
Elemento Función
Página
SP IMP.
Cambia el ajuste de impedancia de los
altavoces.
49
REMOTE ID Selecciona el ID de mando a distancia. 49
TU
Cambia el ajuste de frecuencia de
sintonización de FM/AM.
49
INIT
Restablece los ajustes
predeterminados.
50
UPDATE Actualiza el firmware. 50
VERSION
Comprueba la versión de firmware
instalada actualmente en la unidad.
50
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
SPEAKERS
AB
Cambio del ajuste de impedancia
de los altavoces (SP IMP.)
4 MIN
Seleccione esta opción cuando conecte
altavoces con una impedancia de 4 a menos
de 8 a la unidad.
8 MIN
(predeterminado)
Seleccione esta opción cuando conecte
altavoces con una impedancia de 8 o más a
la unidad.
Selección del ID de mando a
distancia (REMOTE ID)
Cambio del ajuste de frecuencia
de sintonización FM/AM (TU)
FM100/AM10
Seleccione esta opción cuando desee ajustar la
frecuencia FM en pasos de 100 kHz y la de AM en
pasos de 10 kHz.
FM50/AM9
(predeter-
minado)
Seleccione esta opción cuando desee ajustar la
frecuencia FM en pasos de 50 kHz y la de AM en
pasos de 9 kHz.
SP IMP.••8¬MIN
REMOTE ID•AUTO
TU••••FM50/AM9
50 Es
Configuración de los ajustes del sistema (menú ADVANCED SETUP)
Restablece los ajustes predeterminados para la unidad.
Opciones
Se lanzará nuevo firmware con funciones adicionales o
mejoras de productos, según sea necesario. Si la unidad
está conectada a Internet, puede descargar el firmware a
través de la red. Para conocer más detalles, consulte la
información que se suministra con las actualizaciones.
Procedimiento de actualización del
firmware
No realice este procedimiento, a menos que sea necesario
actualizar el firmware. Asimismo, asegúrese de leer la
información que se suministra con las actualizaciones
antes de actualizar el firmware.
1 Pulse SELECT/ENTER repetidamente para
seleccionar “USB” o “NETWORK” y luego
pulse DISPLAY para iniciar la actualización
del firmware.
Opciones
y
Si la unidad detecta un firmware más reciente en la red, “NEW
FW Available” aparecerá como el elemento de menú
“Information” en “Network”. En este caso, también puede
actualizar el firmware de la unidad siguiendo el procedimiento
que se describe en “Actualización del firmware de la unidad a
través de la red” (pág. 51).
Compruebe la versión de firmware instalada actualmente
en la unidad.
y
También puede comprobar la versión del firmware en “Update
(Network Update)” (pág. 47) en el menú “Setup”.
Pueden transcurrir unos instantes hasta que aparezca la versión
del firmware.
Restablecimiento de los ajustes
predeterminados (INIT)
ALL
Restablece los ajustes predeterminados para la
unidad.
NETWORK
Inicialice todos los ajustes de red, Bluetooth y
USB. Cuando realice la inicialización, se
borrará la presintonía (pág. 43) registrada por
la entrada NET/USB.
CANCEL No realiza una inicialización.
Actualización del firmware
(UPDATE)
USB
Actualización del firmware por medio de un
dispositivo de memoria USB.
NETWORK Actualice el firmware a través de la red.
INIT••••CANCEL
UPDATE•NETWORK
Comprobación de la versión del
firmware (VERSION)
VERSION••xx.xx
51 Es
Español
MANEJO
AVANZADO
Se lanzará nuevo firmware con funciones adicionales o mejoras de productos, según sea necesario. Si la unidad está
conectada a Internet, puede descargar el firmware a través de la red y actualizarlo.
y
También puede actualizar el firmware utilizando el dispositivo de
memoria USB desde el menú “ADVANCED SETUP” (pág. 50).
1 Pulse SETUP.
2 Utilice las teclas del cursor (B / C) para
seleccionar “Network” y pulse ENTER.
3 Utilice las teclas del cursor (B / C) para
seleccionar “Information” y pulse ENTER.
Si hay disponible un firmware más reciente, “NEW
FW Available” aparecerá en el visor delantero.
4 Pulse RETURN para volver al estado anterior.
5 Utilice las teclas del cursor (B / C) para
seleccionar “Update” y pulse ENTER.
6 Para iniciar la actualización del firmware,
pulse ENTER.
La unidad se reinicia y la actualización del firmware
comienza.
y
Para cancelar la operación sin actualizar el firmware, pulse
SETUP.
7 Si aparece “UPDATE SUCCESS” en el visor
delantero, pulse A (alimentación) en el panel
delantero.
Ha finalizado la actualización del firmware.
Actualización del firmware de la unidad a través de la red
No controle la unidad ni desconecte el cable de alimentación o el cable de red durante la actualización del firmware. La
actualización de firmware tarda unos 20 minutos o más (dependiendo de la velocidad de conexión de Internet).
Si la unidad está conectada a la red inalámbrica a través de un adaptador de red inalámbrica, es posible que no se pueda actualizar
la red dependiendo del estado de la conexión inalámbrica. En este caso, actualice el firmware utilizando el dispositivo de memoria
USB (pág. 50).
Notas
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
Available
NEW FW
Perform Update
UPDATE
52 Es
INFORMACIÓN ADICIONAL
Consulte el siguiente cuadro cuando esta unidad no funcione bien. Si el problema que tiene no aparece en la lista a
continuación, o si las instrucciones no le sirven de ayuda, ajuste esta unidad en el modo de espera, desconecte el cable de
alimentación y póngase en contacto con el centro de atención al cliente o concesionario Yamaha autorizado más cercano.
General
Resolución de problemas
Problema Causa Remedio
Vea la
página
El equipo no se
enciende.
El circuito de protección se ha activado
tres veces consecutivas. Si la unidad está
en esta condición, el indicador de espera
de la unidad parpadea cuando intenta
activar la alimentación.
Como precaución de seguridad, la capacidad para
activar la alimentación está desactivada. Póngase en
contacto con su centro Yamaha de atención al cliente
o concesionario para solicitar una reparación.
El cable de alimentación no está
conectado o el conector no se ha insertado
completamente.
Conecte el cable de alimentación firmemente.
Los circuitos de protección se han
activado al detectar un cortocircuito, etc.
Compruebe que los cables del altavoz no se tocan y
vuelva a encender la unidad.
12
El microprocesador interno se ha
bloqueado debido a una descarga eléctrica
externa (como un rayo o electricidad
estática excesiva) o a una caída de la
tensión de la fuente de alimentación.
Apague (OFF) la alimentación (A) en el panel
delantero y vuelva a encenderla (ON) una vez
transcurridos al menos 15 segundos. (Si el problema
persiste, desconecte el cable de alimentación de la
toma de CA y vuelva a enchufarlo).
El equipo no se
apaga.
El microprocesador interno se ha
bloqueado debido a una descarga eléctrica
externa (como un rayo o electricidad
estática excesiva) o a una caída de la
tensión de la fuente de alimentación.
Apague (OFF) la alimentación (A) en el panel
delantero y vuelva a encenderla (ON) una vez
transcurridos al menos 15 segundos. (Si el problema
persiste, desconecte el cable de alimentación de la
toma de CA y vuelva a enchufarlo).
No se escucha
sonido.
Conexión incorrecta de cables de salida o
de entrada.
Conecte los cables correctamente. Si el problema
persiste, es posible que los cables estén defectuosos.
11
No se ha seleccionado ninguna fuente de
entrada adecuada.
Seleccione una fuente de entrada adecuada con el
selector INPUT del panel delantero (o con una de las
teclas de selección de entradas del mando a
distancia).
22
Los conmutadores SPEAKERS A/B no
están ajustados correctamente.
Active la opción SPEAKERS A o SPEAKERS B
correspondiente.
22
Las conexiones de los altavoces no son
seguras.
Asegure las conexiones.
11
La salida se ha silenciado. Desactive la función de silencio.
9
El ajuste Max volume o Initial volume se
ha ajustado demasiado bajo.
Compruebe los ajustes para “Max Volume” y “Initial
Volume” en el menú “Setup”.
48
El componente correspondiente a la fuente
de entrada seleccionada está apagado o no
se reproduce.
Encienda el componente y asegúrese de que se está
reproduciendo.
La salida de audio de un dispositivo
conectado a una entrada de audio digital
(tomas COAXIAL/OPTICAL) se ha
configurado en un ajuste distinto de PCM.
Ajuste la salida de audio del dispositivo conectado en
PCM.
53 Es
Resolución de problemas
Español
INFORMACIÓN
ADICIONAL
El sonido desaparece
de repente.
Los circuitos de protección se han
activado al detectar un cortocircuito, etc.
Ajuste la impedancia de los altavoces para que
coincida con la de sus altavoces.
49
Compruebe que los cables del altavoz no se tocan y
vuelva a encender la unidad.
12
La unidad se ha calentado demasiado. Asegúrese de que las aberturas en el panel superior no
están bloqueadas.
La función de standby automático ha
apagado esta unidad.
Cambie la función de standby automático
(“AutoPowerStdby” en el menú “Setup”) para
desactivarla.
48
Solo se escucha el
altavoz de un lado.
Conexión incorrecta de los cables. Conecte los cables correctamente. Si el problema
persiste, es posible que los cables estén defectuosos.
11
Ajuste incorrecto del balance de
altavoces.
Ajuste el control BALANCE en la posición adecuada.
23
No hay graves ni
sensación ambiental.
Los cables + y – se han conectado al revés
en el amplificador o en los altavoces.
Conecte los cables de los altavoces con la fase + y –
correcta.
12
Se oye un sonido de
zumbido.
Conexión incorrecta de los cables. Conecte las tomas de audio con firmeza. Si el
problema persiste, es posible que los cables estén
defectuosos.
11
No hay conexión entre el giradiscos y el
terminal GND.
Establezca la conexión GND entre el giradiscos y esta
unidad.
11
El nivel de volumen
es bajo durante la
reproducción de una
grabación.
La grabación se reproduce en un
giradiscos con un cartucho MC.
El giradiscos debe estar conectado a esta unidad a
través del amplificador de cabezal MC.
El sonido se degrada
al utilizar los
auriculares
conectados al
reproductor de CD o a
la pletina de cinta
conectados a esta
unidad.
Se ha apagado la unidad o está en modo
de espera.
Encienda esta unidad.
El nivel de sonido es
bajo.
La función de control de volumen está
activa.
Baje el volumen, ajuste el control LOUDNESS en la
posición FLAT y luego vuelva a justar el volumen.
23
Problema Causa Remedio
Vea la
página
54 Es
Resolución de problemas
Sintonizador
Problema Causa Remedio
Vea la
página
FM
La recepción
de FM estéreo
tiene ruidos.
Las características particulares de las
emisiones de FM estéreo que se están
recibiendo pueden causar este problema
cuando el transmisor está muy lejos o la
entrada de la antena es deficiente.
Verifique las conexiones de la antena.
Intente utilizar una antena de FM direccional de alta
calidad.
13
Cambie al modo monoaural.
25
Hay distorsión
y no se puede
obtener una
buena
recepción a
pesar de
utilizar una
buena antena
de FM.
Hay interferencia de trayectorias
múltiples.
Ajuste la posición de la antena para eliminar la
interferencia de trayectorias múltiples.
La emisora
deseada no se
puede
sintonizar con
el método de
sintonización
automática.
La señal es demasiado débil. Intente utilizar una antena de FM direccional de alta
calidad.
13
Pruebe a utilizar el método de sintonización manual.
25
FM/
AM
Se muestra NO
PRESETS.
No se registra ninguna emisora
presintonizada.
Registre las emisoras que desee escuchar como
emisoras presintonizadas.
26
AM
La emisora
deseada no se
puede
sintonizar con
el método de
sintonización
automática.
La señal es débil o las conexiones de la
antena están flojas.
Apriete las conexiones de la antena de AM y oriéntela
para obtener la mejor recepción.
Pruebe a utilizar el método de sintonización manual.
25
La
presintonización
automática de
emisoras no
funciona.
La presintonización automática de
emisoras no está disponible para emisoras
de AM.
Utilice la presintonización manual de emisoras.
27
Se oye un ruido
continuo de
siseo y
crepitación.
Los ruidos puedes deberse a relámpagos,
fluorescentes, motores, termostatos y
otros equipos eléctricos.
Utilice una antena exterior y un cable de tierra.
Esto ayudará algo, pero será difícil eliminar todo el
ruido.
Hay ruidos de
zumbidos y
silbidos.
Se está utilizando cerca un aparato de TV. Separe esta unidad del aparato de TV.
55 Es
Resolución de problemas
Español
INFORMACIÓN
ADICIONAL
Bluetooth
Problema Causa Remedio
Vea la
página
No se puede
establecer una
conexión Bluetooth.
La función de Bluetooth de la unidad está
desactivada.
Active la función de Bluetooth en el menú “Setup”.
47
Ya hay otro dispositivo Bluetooth
conectado a la unidad.
Finalice la conexión Bluetooth actual y después
establezca una nueva conexión.
47
La unidad y el dispositivo Bluetooth están
demasiado alejados entre sí.
Acerque el dispositivo Bluetooth a la unidad.
Hay un dispositivo (como un horno
microondas y una LAN inalámbrica)
cercano que emite señales en la banda de
frecuencia de 2,4 GHz.
Aleje la unidad de dichos dispositivos.
El dispositivo Bluetooth no admite A2DP. Utilice un dispositivo Bluetooth que admita A2DP.
Debido a que esta unidad se ha
emparejado con más de 20 dispositivos
Bluetooth, se ha eliminado la información
de emparejado.
Vuelva a intentar el emparejado.
Esta unidad se puede emparejar con un total máximo
de 20 dispositivos Bluetooth para la recepción y la
transmisión. Al registrar el dispositivo 21, se elimina
la información de emparejado utilizada con menos
frecuencia.
29
No se emite sonido, o
el sonido se
interrumpe durante la
reproducción.
El volumen del dispositivo Bluetooth se
ha ajustado demasiado bajo.
Aumente el volumen del dispositivo Bluetooth.
El dispositivo Bluetooth no se ha ajustado
para enviar señales de audio a la unidad.
Cambie la salida de audio del dispositivo Bluetooth a
la unidad.
La conexión Bluetooth ha finalizado. Vuelva a establecer una conexión Bluetooth entre el
dispositivo Bluetooth y la unidad.
29
La unidad y el dispositivo Bluetooth están
demasiado alejados entre sí.
Acerque el dispositivo Bluetooth a la unidad.
Hay un dispositivo (como un horno
microondas y una LAN inalámbrica)
cercano que emite señales en la banda de
frecuencia de 2,4 GHz.
Aleje la unidad de dichos dispositivos.
56 Es
Resolución de problemas
USB y red
Problema Causa Remedio
Vea la
página
La unidad no detecta
el dispositivo USB.
El dispositivo USB no está conectado con
seguridad a la toma USB.
Apague la unidad, vuelva a conectar el dispositivo
USB y vuelva a encender la unidad.
El sistema de archivos del sistema USB
no es FAT16 o FAT32.
Utilice un dispositivo USB con formato FAT16 o
FAT32.
No se pueden ver las
carpetas y archivos
del dispositivo USB.
Los datos del dispositivo USB están
protegidos por el cifrado.
Utilice un dispositivo USB sin función de cifrado.
La función de red no
funciona.
Los parámetros de red (dirección IP) no
están bien configurados.
Active la función del servidor DHCP en su enrutador
y ajuste “DHCP” en el menú “Setup” en “On” en la
unidad. Si desea configurar los parámetros de la red
manualmente, asegúrese de que utiliza una dirección
IP distinta de la que usan otros dispositivos
conectados a su red.
46
La unidad no se
puede conectar a
Internet a través de
un enrutador
inalámbrico (punto de
acceso).
El enrutador inalámbrico (punto de
acceso) está desactivado.
Active el enrutador inalámbrico (punto de acceso).
La unidad y el enrutador inalámbrico
(punto de acceso) están demasiado
alejados.
Coloque la unidad y el enrutador inalámbrico (punto
de acceso) cerca entre sí.
Existe un obstáculo entre la unidad y el
enrutador inalámbrico (punto de acceso).
Mueva la unidad y el enrutador inalámbrico (punto de
acceso) a una ubicación en la que no haya obstáculos
entre ellos.
No se encuentra la
red inalámbrica.
Los hornos de microondas y otros
dispositivos inalámbricos de los
alrededores pueden dificultar la
comunicación inalámbrica.
Apague estos dispositivos.
El acceso a esta red está restringido por
los ajustes de firewall del enrutador
inalámbrico (punto de acceso).
Compruebe el ajuste de firewall del enrutador
inalámbrico (punto de acceso).
La unidad no detecta
el PC.
El ajuste de uso compartido de contenidos
multimedia no es correcto.
Configure el ajuste de uso compartido y seleccione la
unidad como dispositivo en el que se comparte
contenido musical.
31
Algunos programas de seguridad
instalados en el PC bloquean el acceso de
la unidad al PC.
Compruebe los ajustes del programa de seguridad
instalado en el PC.
La unidad y el PC no se encuentran en la
misma red.
Compruebe las conexiones de red y los ajustes del
enrutador y, a continuación, conecte la unidad y el PC
a la misma red.
14
Los archivos del
servidor multimedia
(PC/NAS) no se
pueden ver o
reproducir.
La unidad o el servidor multimedia no
admite los archivos.
Utilice el formato de archivo admitido por la unidad y
por el servidor multimedia. Para obtener información
sobre los formatos de archivo admitidos por la
unidad, consulte “Reproducción de música
almacenada en servidores multimedia (PC/NAS)”.
31
57 Es
Resolución de problemas
Español
INFORMACIÓN
ADICIONAL
Mando a distancia
La radio de Internet
no puede reproducir.
En este momento la emisora de radio por
Internet seleccionada no está disponible.
Es posible que se haya producido un problema de red
con la emisora de radio o que se haya interrumpido el
servicio. Pruebe ese emisora en otro momento o
seleccione otra emisora.
En estos momentos, la emisora de radio
por Internet seleccionada emite silencio.
Algunas emisoras de radio por Internet emiten
silencio durante algunos momentos del día. Pruebe
ese emisora en otro momento o seleccione otra
emisora.
El acceso a esta red está restringido por
los ajustes de firewall de los dispositivos
de red (como, por ejemplo, el enrutador).
Compruebe los ajustes de firewall de los dispositivos
de red. La radio por Internet solo puede reproducirse
cuando pasa por el puerto asignado por cada emisora
de radio. El número de puerto varía en función de la
emisora de radio.
El iPod no reconoce
la unidad cuando se
utiliza AirPlay.
La unidad está conectada a un enrutador
de SSID múltiple.
El acceso a la unidad puede estar restringido por la
función de separación de red en el enrutador. Conecte
el iPod al SSID que pueda acceder a la unidad.
La actualización del
firmware a través de
la red ha fallado.
Es posible que no se pueda realizar en
función del estado de la red.
Actualice el firmware de nuevo a través de la red o
utilice un dispositivo de memoria USB.
50
Problema Causa Remedio
Vea la
página
El mando a distancia
no funciona
correctamente.
La distancia o el ángulo son incorrectos. El mando a distancia tiene un alcance máximo de 6 m
y una inclinación máxima de 30 grados con respecto
al eje del panel delantero.
10
El sensor del mando a distancia de esta
unidad está sometido a la luz solar directa
o a iluminación intensa (lámpara
fluorescente de tipo inverso, por ejemplo).
Coloque la unidad en otro lugar.
Las pilas están casi agotadas. Sustituya las pilas.
Problema Causa Remedio
Vea la
página
58 Es
Indicaciones de error que se muestran en el visor delantero
Mensaje Causa Remedio
Access denied El acceso al PC se ha denegado. Configure los ajustes de uso compartido y seleccione la unidad
como dispositivo en el que se comparte un contenido musical
(pág. 31).
Access error La unidad no puede acceder al dispositivo
USB.
Apague la unidad y vuelva a conectar el dispositivo USB. Si el
problema persiste, pruebe con otro dispositivo USB.
La unidad no puede acceder al iPod. Apague el iPod y vuelva a encenderlo.
El iPod conectado no es compatible con la
unidad.
Utilice un iPod compatible con la unidad (pág. 40).
Hay un problema con la trayectoria de la
señal desde la red hasta la unidad.
Asegúrese de que el enrutador y el módem estén encendidos.
Compruebe la conexión entre la unidad y el enrutador (o nodo)
(pág. 14).
Check SP Wires Se produce un cortocircuito en los cables
de los altavoces.
Retuerza con firmeza los hilos expuestos de los cables y vuelva a
conectarlos correctamente a la unidad y a los altavoces.
No content No hay archivos que puedan reproducirse
en la carpeta seleccionada.
Seleccione una carpeta que contenga archivos compatibles con la
unidad.
Please wait La unidad se está preparando para
conectar a la red.
Espere hasta que desaparezca el mensaje. Si el mensaje se
mantiene durante más de 3 minutos, apague la unidad y vuelva a
encenderla.
Unable to play La unidad no puede reproducir las
canciones almacenadas en el iPod por
algún motivo.
Compruebe los datos de la canción. Si ésta no se puede reproducir
en el propio iPod, puede deberse a que los datos de la canción o el
área de almacenamiento están dañados.
La unidad no puede reproducir las
canciones almacenadas en el PC por algún
motivo.
Compruebe si el formato de los archivos que intenta reproducir es
compatible con la unidad. Para obtener información sobre los
formatos admitidos por la unidad, consulte “Reproducción de
música almacenada en servidores multimedia (PC/NAS)”
(pág. 31). Si la unidad admite el formato de archivo, pero no puede
reproducir ningún archivo, puede que la red esté sobrecargada con
tráfico denso.
Version error La actualización del firmware ha fallado. Vuelva a actualizar el firmware.
59 Es
Español
INFORMACIÓN
ADICIONAL
“Made for iPod” y “Made for iPhone” significan que un
accesorio electrónico se ha diseñado específicamente para
conectarse a un iPod o un iPhone, respectivamente, y que
el desarrollador ha certificado que cumple con los
estándares de rendimiento de Apple.
Apple no se hace responsable del funcionamiento de este
dispositivo ni de su cumplimiento con los estándares
normativos y de seguridad.
Tenga en cuenta que el uso de este accesorio con un iPod o
un iPhone puede afectar al rendimiento inalámbrico.
AirPlay, iPhone, iPod, iPod nano, iPod touch y iTunes son
marcas comerciales de Apple Inc., registradas en los
EE. UU. y en otros países.
DLNA™ y DLNA CERTIFIED™ son marcas
comerciales o marcas registradas de Digital Living
Network Alliance. Todos los derechos reservados. El uso
no autorizado está estrictamente prohibido.
Windows™
Windows es una marca comercial registrada de Microsoft
Corporation en los EE. UU. y en otros países.
Internet Explorer, Windows Media Audio y Windows
Media Player son marcas comerciales o marcas
comerciales Microsoft Corporation en los Estados Unidos
y/o en otros países.
Android™
Android y Google Play son marcas comerciales de
Google, Inc.
El logotipo Wi-Fi CERTIFIED es una marca de
certificación de la Wi-Fi Alliance.
La marca identificadora Wi-Fi Protected Setup es una
marca de la Wi-Fi Alliance.
Wi-Fi, Wi-Fi Alliance, Wi-Fi CERTIFIED, Wi-Fi
Protected Setup, WPA y WPA2 son marcas comerciales o
marcas registradas de la Wi-Fi Alliance.
La marca denominativa Bluetooth
®
y los logotipos son
marcas registradas propiedad de Bluetooth SIG, Inc. y
cualquier uso de dichas marcas por parte de Yamaha
Corporation es bajo licencia.
Bluetooth protocol stack (Blue SDK)
Copyright 1999-2014 OpenSynergy GmbH
Todos los derechos reservados. Todos los derechos sin
publicar reservados.
Explicaciones acerca de GPL
Este producto utiliza el software de código abierto GPL/
LGPL en algunas secciones. Tiene el derecho de obtener,
duplicar, modificar y redistribuir solo este código abierto.
Para obtener información sobre el software de código
abierto GPL/LGPL, cómo obtenerlo y la licencia de GPL/
LGPL, consulte el sitio web de Yamaha Corporation
(http://download.yamaha.com/sourcecodes/musiccast/).
MusicCast es una marca comercial o una marca registrada
de Yamaha Corporation.
Marcas comerciales
60 Es
Red
Toma de entrada: NETWORK x 1 (100Base-TX/10Base-T)
Función PC cliente
Compatible con DLNA ver. 1,5
Compatible con AirPlay
Radio de Internet
Servicio de transmisión
Función Wi-Fi
Capacidad para WPS
Capacidad de uso compartido con dispositivos iOS mediante
conexión inalámbrica y conexión USB
Capacidad para conexión directa con dispositivo móvil
Método de seguridad disponible: WEP, WPA2-PSK (AES),
Mixed Mode
Banda de frecuencia de radio: 2,4 GHz
Estándar de red inalámbrica: IEEE 802.11 b/g/n
Bluetooth
Función de fuente
Esta unidad a dispositivo de vinculación (p. ej. auriculares
Bluetooth
)
Códec compatible........................................................................SBC
Función de vinculación
Dispositivo fuente a esta unidad (p. ej. teléfono inteligente/tablet)
Códec compatible............................................................. SBC, AAC
Capacidad para operación de reproducción/parada desde el
dispositivo de vinculación
•Versión de Bluetooth ....................................................Ver. 2.1+EDR
Perfil compatible ........................................................A2DP, AVRCP
Salida inalámbrica.................................................. Bluetooth Clase 2
Distancia de comunicación máxima................ 10 m sin interferencia
USB
Toma de entrada: USB x 1 (USB2.0)
Capacidad para iPod, memoria USB de almacenamiento masivo
Capacidad de suministro de corriente: 1,0 A
Audio
Potencia de salida RMS mínima
(De 20 Hz a 20 kHz, 0,04% THD, 8 ) ................... 80 W + 80 W
Potencia dinámica por canal (IHF) (8/6/4/2 )
............................................................................ 105/125/150/178 W
Potencia máxima por canal (1 kHz, 0,7% THD, 4 )
[Modelos del R.U. y Europa] ............................................... 105 W
Potencia IEC (1 kHz, 0,04% THD, 8 )
[Modelos del R.U. y Europa] ................................................. 84 W
Ancho de banda de potencia (L/R principal)
(0,06%THD 40,0 W, 8) ................................. De 10 Hz a 50 kHz
Factor de amortiguación (SPEAKERS A)
1 kHz, 8 .......................................................................150 o más
Potencia de salida efectiva máxima (JEITA)
(1 kHz, 10% THD, 8 )
[Modelos de Asia y general] .................................................115 W
Sensibilidad de entrada/impedancia de entrada
PHONO (MM) ......................................................... 3,5 mV/47 k
CD, etc. .................................................................. 200 mV/47 k
Señal de entrada máxima
PHONO (MM) (1 kHz, 0,003% THD) ......................60 mV o más
CD, etc. (1 kHz, 0,5% THD)........................................ 2,2 V o más
Nivel de salida/impedancia de salida
CD, etc. (entrada a 1 kHz, 200 mV)
OUT .................................................................... 200 mV/1,1 k
SUBWOOFER PRE OUT .................................... 4,0 V / 1,2 k
(frecuencia de corte) ...........................................................90 Hz
PHONES (8 de carga) ...................................... 410 mV/470
Respuesta de frecuencia
CD, etc. (de 20 Hz a 20 kHz) ........................................ 0 ± 0,5 dB
CD, etc. (de 10 Hz a 100 kHz, PURE DIRECT activado)
..................................................................................... 0 ± 1,0 dB
Desviación de ecualización RIAA
PHONO (MM) .................................................................. ± 0,5 dB
Distorsión armónica total
PHONO (MM) a OUT
(De 20 Hz a 20 kHz, 3 V).................................. 0,025% o menos
CD, etc. a SPEAKERS
(de 20 Hz a 20 kHz, 40,0 W, 8 ) .................... 0,015% o menos
Relación señal a ruido (red IHF-A)
PHONO (MM) (entrada cortocircuitada, 5 mV) .........87 dB o más
CD, etc. (entrada cortocircuitada, 200 mV)...............100 dB o más
Ruido residual (red IHF-A) ......................................................30 µV
Separación de canales
CD, etc. (entrada de 5,1 k cortocircuitada, 1/10 kHz)
.............................................................................65/50 dB o más
Características de control de tono
BASS
Refuerzo/corte (20 Hz) ................................................... ± 10 dB
Frecuencia de transición ................................................... 350 Hz
TREBLE
Refuerzo/corte (20 kHz) ................................................. ± 10 dB
Frecuencia de transición .................................................. 3,5 kHz
Control de volumen continuo
Atenuación 1 kHz .................................................................-30 dB
Error de seguimiento de ganancia (de +16,5 a -80 dB)
...................................................................................0,5 dB o menos
Entrada digital (OPTICAL/COAXIAL)
Compatibilidad con frecuencia de muestra de audio
.................................................... 32/44,1/48/88,2/96/176,4/192 kHz
FM
Gama de sintonización
[Modelos de EE. UU. y Canadá] .................. De 87,5 a 107,9 MHz
[Modelos de Asia y general]
.............................................De 87,5/87,50 a 108,0/108,00 MHz
[Modelos de Reino Unido, Europa, Corea y Australia]
............................................................... De 87,50 a 108,00 MHz
Umbral de silenciamiento de 50 dB (IHF, 1 kHz, 100% MOD.)
Mono .................................................................. 3,0 µV (20,8 dBf)
Relación señal a ruido (IHF)
Mono/estéreo ............................................................. 65 dB/64 dB
Distorsión armónica (1 kHz)
Mono/estéreo ................................................................ 0,5%/0,6%
Entrada de antena...............................................75 W desequilibrada
AM
Gama de sintonización
[Modelos de EE. UU. y Canadá] .....................De 530 a 1710 kHz
[Modelos de Asia y general] ............De 530/531 a 1710/1611 kHz
[Modelos de Reino Unido, Europa, Corea y Australia]
.......................................................................De 531 a 1611 kHz
Generalidades
Fuente de alimentación
[Modelos de EE. UU. y Canadá] .........................120 V CA, 60 Hz
[Modelo general] ...................... 110-120/220-240 V CA, 50/60 Hz
[Modelo de Corea]...............................................220 V CA, 60 Hz
[Modelo de Australia]..........................................240 V CA, 50 Hz
[Modelos de Reino Unido y Europa]...................230 V CA, 50 Hz
[Modelo de Asia] .................................... 220-240 V CA, 50/60 Hz
Consumo eléctrico ................................................................... 190 W
Modo desactivado..................................................................... 0,1 W
Consumo en espera (datos de referencia) ................................. 0,1 W
Network Standby activado
Por cable ................................................................................ 1,7 W
Inalámbrica (Wi-Fi/Wireless Direct/Bluetooth)
...................................................................... 1,8 W/1,9 W/1,6 W
Consumo de potencia máximo (1 kHz, 8 , 10% THD)
[Modelos del R.U., Australia, Asia y general] ..................... 380 W
Dimensiones (An. Al. Pr.) ......................... 435 151 392 mm
Peso...........................................................................................9,8 kg
*Las especificaciones están sujetas a cambios sin previo aviso.
Especificaciones
Índice
61 Es
Español
INFORMACIÓN
ADICIONAL
A
Actualización del firmware................................ 47, 50, 51
AirPlay ........................................................................... 36
Ajuste de la dirección IP................................................ 46
Ajuste de paso de frecuencia ................................... 25, 49
Ajuste de volumen inicial .............................................. 48
Ajuste de volumen máximo ........................................... 48
Ajuste manual de red ..................................................... 19
Antena inalámbrica .......................................................... 8
Antena inalámbrica (Wi-Fi)........................................... 14
Audio Receive (Bluetooth, menú Setup) ....................... 47
Audio Send (Bluetooth, menú Setup) ............................ 47
Auriculares....................................................................... 6
Auto Power Standby ...................................................... 48
Auto Preset (menú Option)............................................ 26
AutoPowerStdby (menú Setup) ..................................... 48
B
Balance de altavoces...................................................... 23
Bluetooth........................................................................ 29
Bluetooth (menú Setup) ................................................. 47
Bluetooth Standby ......................................................... 47
Bookmark (radio de Internet) ........................................ 35
C
Cable de red ................................................................... 14
Cambio de la información (visor delantero) .................. 42
Clear Preset (menú Option) ........................................... 28
Conector tipo banana ..................................................... 12
Conexión (Bluetooth) .................................................... 29
Conexión (iPod)............................................................. 40
Conexión (USB) ............................................................ 38
Conexión de cables de los altavoces.............................. 12
Conexión de dispositivo de audio.................................. 11
Conexión de doble cable................................................ 12
Conexión de la antena de AM ....................................... 13
Conexión de la antena de FM ........................................ 13
Conexión de NAS (Network Attached Storage)............ 14
Conexión de PC ............................................................. 14
Conexión de red ....................................................... 16, 21
Conexión de red (LAN inalámbrica) ........... 17, 18, 19, 20
Conexión de red (menú Setup) ...................................... 46
Conexión de red (por cable) .......................................... 14
Conexión de servidor..................................................... 14
Conexión del cable de alimentación .............................. 15
Conexión inalámbrica (Bluetooth) ................................ 29
Conexión inalámbrica (red) ......................... 17, 18, 19, 20
Conexión por cable (red) ............................................... 14
Conexiones de los altavoces .......................................... 12
Configuración del botón pulsador WPS ........................ 18
Configuración del uso compartido de medios ............... 31
Connection (Network, menú Setup) .............................. 46
Control BALANCE ....................................................... 23
Control BASS ................................................................ 23
Control de tono .............................................................. 23
Control de volumen ....................................................... 22
Control LOUDNESS...................................................... 23
Control TREBLE ........................................................... 23
D
DHCP (Network, menú Setup) ...................................... 46
Digital Media Controller................................................ 46
DIMMER ......................................................................... 5
DISPLAY....................................................................... 42
DLNA............................................................................. 31
DMC Control (Network, menú Setup)........................... 46
E
ECO Mode (menú Setup)............................................... 48
Emparejado (Bluetooth)................................................. 29
Escucha de radio AM ..................................................... 25
Escucha de radio FM...................................................... 25
Estado de conexión de red ............................................. 21
Estéreo (radio FM) ......................................................... 26
F
Formato de archivos de audio (PC/NAS) ...................... 31
Formato de archivos de audio (USB)............................. 38
Función de presintonía ................................................... 43
I
ID de mando a distancia................................................. 49
ID del sistema................................................................. 47
Impedancia del altavoz................................................... 49
Indicación de error ......................................................... 58
Indicador Bluetooth.......................................................... 7
Indicador de intensidad de señal ...................................... 7
Indicador SLEEP............................................................ 24
Indicador Wi-Fi................................................................ 7
Indicadores de altavoces .................................................. 7
Información de red ......................................................... 46
Information (Network, menú Setup) .............................. 46
Inicializar ....................................................................... 50
INIT (menú ADVANCED SETUP) .............................. 50
Initial Volume (menú Setup).......................................... 48
IP Address (Network, menú Setup) ............................... 46
M
Mando a distancia (controles y funciones) ...................... 9
Manejo de reproducción básico ..................................... 22
MANUAL (Wireless, menú Setup) ............................... 19
Max Volume (menú Setup)............................................ 48
MEMORY................................................................ 27, 43
Menú ADVANCED SETUP.......................................... 49
Menú Option .................................................................. 44
Menú Setup .................................................................... 45
Método de conexión (red) .............................................. 46
Modo de ahorro energético ............................................ 48
Modo FM ....................................................................... 26
Mono (radio FM) ........................................................... 26
MusicCast CONTROLLER ............................................. 3
Índice
62 Es
Índice
N
Net Radio....................................................................... 34
Network (menú Setup) .................................................. 46
Network Name (Network, menú Setup) ........................ 47
Network Standby........................................................... 46
NUEVO FW disponible ................................................ 51
O
OPTION ........................................................................ 44
P
Panel delantero (controles y funciones) .......................... 5
Panel trasero (controles y funciones) .............................. 8
Paso de frecuencia de sintonizador................................ 25
Perform Update ............................................................. 47
Pilas ............................................................................... 10
Preselección (radio FM/AM)......................................... 27
Preselección auto (radio FM) ........................................ 26
Presintonía ..................................................................... 43
Presintonía (red) ............................................................ 43
R
Radio de Internet (vTuner) ............................................ 34
Recepción de audio (Bluetooth) .................................... 47
REMOTE ID (menú ADVANCED SETUP) ................ 49
REPEAT (iPod) ............................................................. 41
REPEAT (PC/NAS) ...................................................... 33
REPEAT (USB) ............................................................ 39
Repetición (iPod)........................................................... 41
Repetición (PC/NAS) .................................................... 33
Repetición (USB) .......................................................... 39
Reproducción (AirPlay)................................................. 36
Reproducción (Bluetooth) ............................................. 29
Reproducción (iPod)...................................................... 40
Reproducción (PC/NAS)............................................... 31
Reproducción (radio de Internet)................................... 34
Reproducción (radio FM/AM) ...................................... 25
Reproducción (USB) ..................................................... 38
Reproducción aleatoria (iPod)....................................... 41
Reproducción aleatoria (PC/NAS) ................................ 33
Reproducción aleatoria (USB) ...................................... 39
Reproducción de contenido de iTunes (AirPlay) .......... 36
Reproducción de contenido de PC ................................ 31
Reproducción de contenido del iPod (AirPlay)............. 36
Reproducción de contenido del iPod (USB) ................. 40
Reproducción de contenido NAS .................................. 31
Reproducción de contenido USB .................................. 38
S
Security (Wireless Direct, menú Setup) ........................ 20
Security (Wireless, menú Setup) ................................... 19
Security Key (Wireless Direct, menú Setup) ................ 20
Security Key (Wireless, menú Setup) ........................... 19
Selección de altavoces................................................... 22
Selección de tensión ...................................................... 15
Selector INPUT ............................................................. 22
Server............................................................................. 31
SETUP........................................................................... 45
SHUFFLE (iPod)........................................................... 41
SHUFFLE (PC/NAS) .................................................... 33
SHUFFLE (USB)........................................................... 39
Signal Info. (menú Option)............................................ 44
SP IMP. (Menú ADVANCED SETUP) ........................ 49
SPEAKERS A/B............................................................ 22
SSID (Wireless Direct, menú Setup) ............................. 20
SSID (Wireless, menú Setup) ........................................ 19
Standby (Bluetooth, menú Setup).................................. 47
Standby (Network, menú Setup).................................... 46
STATUS (Information, menú Setup)............................. 21
T
Teclas de selección de entradas ..................................... 22
Temporizador para dormir............................................. 24
Toma PHONES ............................................................... 6
Tomas ANTENNA ........................................................ 13
Tomas CD .................................................................. 8, 11
Tomas COAXIAL...................................................... 8, 11
Tomas LINE .............................................................. 8, 11
Tomas OPTICAL....................................................... 8, 11
Tomas PHONO.......................................................... 8, 11
Tomas SUBWOOFER PRE OUT ............................. 8, 11
Transmisión de audio (Bluetooth) ................................. 47
TU (menú ADVANCED SETUP)................................. 49
U
UPDATE (menú ADVANCED SETUP) ...................... 50
Update (Network, menú Setup) ..................................... 47
USB................................................................................ 38
USB (iPod)..................................................................... 40
Uso compartido del ajuste de conexión Wi-Fi
(dispositivo iOS) ............................................................ 17
V
VERSION (menú ADVANCED SETUP)..................... 50
Version (Network, menú Setup) .................................... 47
Versión del firmware ............................................... 47, 50
Visor delantero (controles y funciones)........................... 7
Vol.Interlock (menú Option) ......................................... 44
VOLTAGE SELECTOR ........................................... 8, 15
Volume Interlock (menú Option) .................................. 44
Volume Trim (menú Option)......................................... 44
W
WAC .............................................................................. 17
Wired (Network, menú Setup)....................................... 46
Wireless (Network, menú Setup)................................... 46
Wireless (WAC) (Wireless, menú Setup)...................... 17
Wireless Accessory Configuration ................................ 17
Wireless Direct .............................................................. 20
WirelessDirect (Network, menú Setup)......................... 46
WPS (Wireless, menú Setup)......................................... 18
Printed in Malaysia ZS22690-1© 2015 Yamaha Corporation
Network Receiver
R-N602
OWNER’S MANUAL
MANUAL DE INSTRUCCIONES
RL
1 / 1

Yamaha R-N602 El manual del propietario

Categoría
Receptores de medios de coche
Tipo
El manual del propietario

En otros idiomas