Yamaha RX-V2200 Manual de usuario

Marca: Yamaha

Modelo: RX-V2200

Categoría: Receptor

Tipo: Manual de usuario

OWNER’S MANUAL

RX-V2200

AV Receiver

IMPORTANT

Please record the serial number of this unit in the

space below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia

V795410

0100V2200(U)-cv1/4 01.8.1, 10:24 AM1

I CAUTION

SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

you to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert you to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

1 Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and use instructions

should be followed.

5 Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning.

6 Attachments – Do not use attachments not recommended

by the product manufacturer as they may cause hazards.

7 Water and Moisture – Do not use this product near water –

for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a swimming pool;

and the like.

8 Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall,

causing serious injury to a child or adult, and serious

damage to the product. Use only with a cart, stand, tripod,

bracket, or table recommended by the manufacturer, or sold

with the product. Any mounting of the product should

follow the manufacturer’s instructions, and should use a

mounting accessory recommended by the manufacturer.

9 A product and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause the

product and cart combination to overturn.

10 Ventilation – Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the

product and to protect it from overheating, and these

openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed,

sofa, rug, or other similar surface. This product should not

be placed in a built-in installation such as a bookcase or

rack unless proper ventilation is provided or the

manufacturer’s instructions have been adhered to.

11 Power Sources – This product should be operated only from

the type of power source indicated on the marking label. If

you are not sure of the type of power supply to your home,

consult your product dealer or local power company. For

products intended to operate from battery power, or other

sources, refer to the operating instructions.

12 Grounding or Polarization – This product may be equipped

with a polarized alternating current line plug (a plug having

one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

13 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or pinched

by items placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles, and the

point where they exit from the product.

14 Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

15 Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from touching

such power lines or circuits as contact with them might be

fatal.

16 Overloading – Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result

in a risk of fire or electric shock.

17 Object and Liquid Entry – Never push objects of any kind

into this product through openings as they may touch

dangerous voltage points or short-out parts that could result

in a fire or electric shock. Never spill liquid of any kind on

the product.

18 Servicing – Do not attempt to service this product yourself

as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

19 Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service personnel

under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into

the product,

c) If the product has been exposed to rain or water,

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

0101V2200_Cau_EN(U) 01.8.1, 9:43 AM2

SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS

CAUTION II

1. IMPORTANT NOTICE : DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved

by Yamaha may void your authority, granted by the

FCC, to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result in

harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and,

if not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If

this product is found to be the source of interference,

which can be determined by turning the unit “OFF” and

“ON”, please try to eliminate the problem by using one

of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

FCC INFORMATION (for US customers only)

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular,

specifies that the cable ground shall be connected to the

grounding system of the building, as close to the point of

cable entry as practical.

d) If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions as an

improper adjustment of other controls may result in

damage and will often require extensive work by a

qualified technician to restore the product to its normal

operation,

e) If the product has been dropped or damaged in any

way, and

f) When the product exhibits a distinct change in

performance - this indicates a need for service.

20 Replacement Parts – When replacement parts are

required, be sure the service technician has used

replacement parts specified by the manufacturer or have

the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric

shock, or other hazards.

21 Safety Check – Upon completion of any service or

repairs to this product, ask the service technician to

perform safety checks to determine that the product is in

proper operating condition.

22 Wall or Ceiling Mounting – The unit should be mounted

to a wall or ceiling only as recommended by the

manufacturer.

23 Heat – The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

24 Outdoor Antenna Grounding – If an outside antenna or

cable system is connected to the product, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA

70, provides information with regard to proper grounding of

the mast and supporting structure, grounding of the lead-in

wire to an antenna discharge unit, size of grounding

conductors, location of antenna discharge unit, connection

to grounding electrodes, and requirements for the

grounding electrode.

0101V2200_Cau_EN(U) 01.8.1, 9:43 AM3

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this unit in a well ventilated, cool, dry, clean

place with at least 30 cm on the top, 20 cm on the

right and left, and 10 cm at the back of this unit

— away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold.

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds. To prevent fire or electrical

shock, do not place this unit where it may get

exposed to rain, water, and/or any type of liquid.

4 Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this

unit in a environment with high humidity (i.e. a

room with a humidifier) to prevent condensation

inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal

injury.

5 On the top of this unit, do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may

cause fire, damage to this unit, and/or personal

injury.

– Containers with liquid in them, as they may

cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper,

tablecloth, curtain, etc. in order not to obstruct

heat radiation. If the temperature inside this unit

rises, it may cause fire, damage to this unit, and/or

personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

III CAUTION

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than

specified is dangerous and may cause fire,

damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any

damage resulting from use of this unit with a

voltage other than specified.

13 To prevent damage by lightning, disconnect the

power cord from the wall outlet during an

electrical storm.

14 Take care of this unit so that no foreign objects

and/or liquid drops inside this unit.

15 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

16 When not planning to use this unit for long

periods of time (i.e. vacation), disconnect the AC

power plug from the wall outlet.

17 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding

that this unit is faulty.

18 Before moving this unit, press STANDBY/ON to set

this unit in the standby mode, and disconnect the

AC power plug from the wall outlet.

19 VOLTAGE SELECTOR (China and General models

only)

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local main voltage

BEFORE plugging into the AC main supply.

Voltages are 110/120/220/240 V AC, 50/60 Hz.

This unit is not disconnected from the AC power

source as long as it is connected to the wall outlet,

even if this unit itself is turned off. This state is called

the standby mode. In this state, this unit is designed to

consume a very small quantity of power.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer

Electronics Group want you to get the most out of your equipment

by playing it at a safe level. One that lets the sound come through

loud and clear without annoying blaring or distortion – and, most

importantly, without affecting your sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

0101V2200_Cau_EN(U) 01.8.1, 10:18 AM4

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADDITIONAL

INFORMATION

ADVANCED

OPERATION

CONTENTS

INTRODUCTION

CONTENTS ....................................................... 1

FEATURES ........................................................ 2

GETTING STARTED ....................................... 3

Checking the Package Contents ............................... 3

Installing Batteries in the Remote Control ............... 3

CONTROLS AND FUNCTIONS .................... 4

Front Panel ............................................................... 4

Remote Control ........................................................ 6

Using the Remote Control ........................................ 7

Front Panel Display .................................................. 8

Rear Panel ................................................................ 9

PREPARATION

SPEAKER SETUP .......................................... 10

Speakers to Be Used ............................................... 10

Speaker Placement ................................................. 10

Connecting the Speakers ........................................ 11

CONNECTIONS ............................................. 14

Before Connecting Components ............................ 14

Connecting Video Components .............................. 14

Connecting Audio Components ............................. 16

Connecting to an External Amplifier ..................... 18

Connecting an External Decoder ............................ 18

Connecting the Power Supply Cords ...................... 19

Turning on the Power ............................................. 20

ON-SCREEN DISPLAY (OSD) ..................... 21

OSD Modes ............................................................ 21

Selecting the OSD Mode ........................................ 21

SPEAKER MODE SETTINGS ..................... 22

Summary of SPEAKER SET Items 1A through 1F ...

ADJUSTING THE SPEAKER OUTPUT

LEVELS ....................................................... 23

Before You Begin ................................................... 23

Using the Test Tone (TEST DOLBY SUR.) .......... 23

BASIC OPERATION

BASIC PLAYBACK ........................................ 25

Input Modes and Indications .................................. 27

Selecting a Sound Field Program ........................... 28

Selecting PRO LOGIC or Neo: 6 ....................... 29

DIGITAL SOUND FIELD PROCESSING

(DSP) ............................................................ 31

Understanding Sound Fields .................................. 31

Hi-Fi DSP Programs............................................... 31

CINEMA-DSP ................................................. 32

Sound Design of CINEMA-DSP ............................ 32

CINEMA-DSP Programs ....................................... 34

TUNING ........................................................... 36

Connecting the Antennas ........................................ 36

Automatic and Manual Tuning ............................... 37

Presetting Stations .................................................. 38

Tuning in to a Preset Station .................................. 40

Exchanging Preset Stations .................................... 40

BASIC RECORDING ..................................... 41

ADVANCED OPERATION

REMOTE CONTROL FEATURES .............. 42

Control Area ........................................................... 42

Setting the Manufacturer Code .............................. 43

Programming a New Remote Control Function

(Learn Feature) ................................................... 44

Using the Macro Feature ........................................ 45

Changing the Source Name in the Display Window

............................................................................ 47

Clearing Learned Functions, Macros, Renamed

Source Names, and Setup Manufacturer Codes ...

Clearing a Learned Function or Macro .................. 48

Each Component Control Area .............................. 50

SET MENU ...................................................... 55

Adjusting the Items on the SET MENU................. 55

1 SPEAKER SET (speaker mode settings) ........... 56

2 LOW FRQ TEST ............................................... 59

3 L/R BALANCE (balance of the left and right main

speakers)............................................................. 60

4 HP TONE CTRL (headphone tone control) ....... 60

5 CENTER GEQ (center graphic equalizer) ......... 60

6 INPUT RENAME .............................................. 61

7 I/O ASSIGNMENT ............................................ 61

8 INPUT MODE (initial input mode) ................... 62

9 PARAM. INI (parameter initialization) ............. 63

10 LFE LEVEL ..................................................... 63

11 DYNAMIC RANGE ......................................... 64

12 SP DELAY TIME ............................................. 64

13 DISPLAY SET .................................................. 65

14 MEMORY GUARD ......................................... 65

ADJUSTING THE LEVEL OF THE EFFECT

SPEAKERS .................................................. 66

SLEEP TIMER ................................................ 67

Setting the Sleep Timer .......................................... 67

Canceling the Sleep Timer ..................................... 67

ZONE 2 ............................................................ 68

Zone 2 Connections ................................................ 68

Remote Control in Zone 2 ...................................... 69

ADDITIONAL INFORMATION

SOUND FIELD PROGRAM PARAMETER

EDITING ..................................................... 70

What is a sound field? ............................................ 70

Sound Field Program Parameters ........................... 70

Changing Parameter Settings ................................. 71

Resetting a Parameter to the Factory-set Value ...... 71

DIGITAL SOUND FIELD PARAMETER

DESCRIPTIONS ......................................... 72

TROUBLESHOOTING .................................. 76

GLOSSARY ..................................................... 81

SPECIFICATIONS ......................................... 83

0102V2200_1-9_EN(U) 01.8.1, 9:43 AM1

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

“DTS”, “DTS-ES Extended Surround” and “Neo: 6” are

trademarks of Digital Theater System, Inc.

FEATURES

Built-in 6-Channel Power Amplifier

◆ Minimum RMS Output Power

(0.04% THD, 20 Hz – 20 kHz, 8Ω)

Main: 100 W + 100 W

Center: 100 W

Rear: 100 W + 100 W

Rear center: 100 W

Multi-Mode Digital Sound Field

Processing

◆ Dolby Pro Logic/Dolby Pro Logic Decoder

◆ Dolby Digital/Dolby Digital Matrix 6.1 Decoder

◆ DTS/DTS ES Matrix 6.1, Discrete 6.1, DTS

Neo: 6 Decoder

◆ CINEMA DSP: Combination of YAMAHA DSP

Technology and Dolby Pro Logic, Dolby Digital

or DTS

◆ Virtual CINEMA DSP

◆ SILENT CINEMA DSP

Sophisticated AM/FM Tuner

◆ 40-Station Random Access Preset Tuning

◆ Automatic Preset Tuning

◆ Preset Station Shifting Capability (Preset

Editing)

Other Features

◆ 96-kHz/24-bit D/A Converter

◆ “SET MENU” which Provides You with 14 Items

for Optimizing This Unit for Your Audio/Video

System

◆ Test Tone Generator for Easier Speaker Balance

Adjustment

◆ 6-Channel External Decoder Input for Other

Future Formats

◆ BASS EXTENSION Button for Reinforcing

Bass Response

◆ On Screen Display Function Helpful in

Controlling This Unit

◆ S Video Signal Input/Output Capability

◆ Component Video Input/Output Capability

◆ Optical and Coaxial Digital Audio Signal Jacks

◆ Sleep Timer

◆ Remote Control with Preset Manufacturer Codes

and “Learning” Capability

◆ PROCESSOR DIRECT for no alteration of the

original signal

◆ Custom Installation Facility

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control, the button name on the remote control is given in parentheses in this

manual.

0102V2200_1-9_EN(U) 01.8.1, 9:43 AM2

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

TRANSMIT

RE-NAME

STANDBY

6CH INPUT

SOUND

SYSTEM

CLEAR LEARN MACRO

OFF ON

MACRO

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

PARAMETER

SET MENU

EFFECT

LEVEL

ON SCREEN

TESTSLEEP

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AU X

POWER

100

11 12

234

Installing Batteries in the Remote

Control

1 Open the battery compartment cover.

2 Insert three supplied batteries (R6) in the

correct direction by aligning the + and –

marks on the batteries with the polarity

markings (+ and –) on the inside of the

battery compartment.

3 After new batteries are correctly inserted,

press the RESET button in the battery

compartment using a ball point pen or

similar object. (This does not clear the

contents of the memory.)

4 Replace the cover as pressing until it snaps

into place.

■ Notes on batteries

• Change all of the batteries if you notice the condition

like; the operating range of the remote control

decreases, the indicator does not flash or its light

becomes dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have

the same shape and color.

• If the batteries have leaked, dispose of them

immediately. Avoid touching the leaked material or

letting it come into contact with clothing, etc. Clean

the battery compartment thoroughly before installing

new batteries.

If the remote control is without batteries for more than

3 minutes, or if exhausted batteries remain in the

remote control, the contents of the memory may be

cleared. When the memory is cleared, insert new

batteries, set up the manufacturer code and program

any acquired functions that may have been cleared.

Connection GuideAM loop antenna

Indoor FM antenna

(Australia model)

Indoor FM antenna

(U.S.A., Canada, China and

General models)

Batteries (3) (R6)

Remote control

GETTING STARTED

Checking the Package Contents

Check your package to make sure it has the following items.

Power Cord

(U.S.A., and Canada models

only)

RESET button

CENTER

SUB

WOOFER

S VIDEO

MONITOR OUT

VIDEO

DIGITAL OUTPUT

DIGITAL INPUT

6CH INPUT

GND

AUDIO AUDIO VIDEO

SPEAKERS

TUNER

75Ω UNBAL.

ANT

GND

ANT

COMPONENT VIDEO

S VIDEO

DVD

D-TV

/LD

CBL

/SAT

VIDEO

/ C

DVD

MONITOR

OUT

D-TV / LD

MAIN

REAR

CENTER

REAR

/ C

OPTICAL

TAPE

(

PLAY

)

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD-R

DVD

D-TV

PHONO

OUT

VCR 2

/DVR

VCR 1

MAIN

SURROUND

/LD

CBL

/SAT

(SURROUND)

COAXIAL

–

SUB

WOOFER

AUDIO OUT S VIDEO

OUT

VIDEO

OUT

OPTICAL

COMPONENT

VIDEO OUT

AUDIO

OUT

S VIDEO IN VIDEO IN

S VIDEO

OUT

VIDEO

OUT

OPTICAL

COMPONENT

VIDEO IN

COMPONENT

VIDEO OUT

RIGHT LEFT

RIGHT

LEFT

L R

DVD Player Main Speaker

TV Subwoofer Center Speaker Rear Center

Speaker

Rear Speaker

CONNECTION

GUIDE

Analog audio signal

Optical digital signal

S video signal

Video signal

Signal flow

V795390

0102V2200_1-9_EN(U) 01.8.1, 9:43 AM3

BASS

VOLUMEINPUT

INPUT M0DE

VIDEO AUX

SILENT

PROGRAM

STEREO

SPEAKERS

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

STANDBY

NATURAL SOUND AV RECEIVER

6CH INPUT

–+

TREBLE

–+

PRO LOGIC

DIGITAL

REC OUT/ZONE 2

V-AUX

VCR2

/DVR

VCR1

PHONO

TUNER

MD/TAPE

DVD

SOURCE

/REMOTE

D-TV/LD

CBL/SAT

CD-R

123 4567

90 qw

PRESET

/TUNING

EDIT

MEMORY

MAN'L/AUTO FM

TUNING

MODE

AUTO/MAN'L MONO

FM/AM

CONTROLS AND FUNCTIONS

Front Panel

1 STANDBY/ON

Turns on and sets this unit in the standby mode. When

you turn on this unit, you will hear a click and there will

be a 4 to 5-second delay before this unit can reproduce

sound.

Standby mode

In this mode, this unit consumes a small amount of

power to receive infrared-signals from the remote

control.

2 Remote control sensor

Receives signals from the remote control.

3 Front panel display

Shows information about the operational status of this

unit (see page 8).

4 INPUT MODE

Sets the priority for the types of input signals (AUTO,

DTS, ANALOG) to receive when one component is

connected to two or more input jacks of this unit (see

page 27). Priority cannot be set when 6CH INPUT is

selected as the input source.

5 INPUT l / h

Selects the input source you want to listen to or watch.

6 VOLUME

Controls the output level of all audio channels.

This does not affect the REC OUT level.

7 6CH INPUT

Selects the source connected to the 6CH INPUT jacks.

The source selected by pressing 6CH INPUT takes

priority over the source selected with INPUT l / h (or

the input selector buttons on the remote control).

8 SPEAKERS A/B

Turn on or off the set of main speakers connected to the A

and/or B terminals on the rear panel at each time its

corresponding button is pressed.

9 BASS EXTENSION

Turns on or off the BASS EXTENSION function at each

time the button is pressed, this feature boosts the bass

frequency of the left and right main channels by +6 dB

(60 Hz) while maintaining overall tonal balance. This

boost is useful if you do not use a subwoofer.

However, this boost may not be noticeable if “1B MAIN

SP” on the SET MENU is set to SMALL and “1E LFE/

BASS OUT” is set to SWFR.

0 PROCESSOR DIRECT

Turns on or off the PROCESSOR DIRECT function at

each time the button is pressed. When this is on, BASS,

TREBLE, and BASS EXTENSION are bypassed,

eliminating any alteration of the original signal.

0102V2200_1-9_EN(U) 01.8.1, 9:43 AM4

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

To open, press gently on the lower part of the panel.

q REC OUT/ZONE 2

Selects the source you want to direct to the audio/video

recorder and ZONE 2 outputs independent of the source

you are listening to in the main room. When set to the

SOURCE/REMOTE position, the input source is directed

to all outputs.

w STEREO/EFFECT

Switches the normal stereo or DSP effect reproduction.

When STEREO is selected, 2-channel input signals are

directed to the main left and right speakers without effect

sounds. All Dolby Digital and DTS audio signals except

for the LFE channel are mixed down to the main left and

right speakers.

e A/B/C/D/E

Selects one of the 5 preset station groups (A to E).

r PROGRAM l / h

Selects the DSP program (see page 28).

t PRESET/TUNING l / h

Selects preset station number 1 to 8 when the colon (:)

appears next to the band indication on the front panel

display, and selects the tuning frequency when the colon

(:) does not appear.

y PHONES jack

Outputs audio signals for private listening with

headphones. When you connect headphones, no signals

are output to the OUTPUT jacks or to the speakers.

u VIDEO AUX jacks

Inputs audio and video signals from a portable external

source such as a game console. To reproduce source

signals from these jacks, select V-AUX as the input

source.

i PRESET/TUNING EDIT

Switches the function of PRESET/TUNING l / h (the

colon (:) turns on or off) between selecting a preset

station number and tuning.

This button is also used to exchange the assignment of

two preset stations with each other.

o FM/AM

Switches the reception band between FM and AM.

p MEMORY (MAN’L/AUTO FM)

Stores a station in the memory. Hold down this button for

more than 3 seconds to start automatic preset tuning.

a TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic and manual.

To select the automatic tuning mode, press this button so

that the “AUTO” indicator lights up on the front panel

display. To select the manual tuning mode, press this

button so that the “AUTO” indicator does not light up.

s BASS

Adjusts the low-frequency response for the left and right

main channels.

Turn the control to the right to increase or to the left to

decrease the low-frequency response.

d TREBLE

Adjusts the high-frequency response for the left and right

main channels.

Turn the control to the right to increase or to the left to

decrease the high-frequency response.

Note

• If you increase or decrease the high-frequency or the low-

frequency sound to an extreme level, the tonal quality from the

center and rear speakers may not match that of the left and

right main speakers.

■ Opening and closing the front

panel door

When you are not operating the controls behind the front

panel door, close the door.

0102V2200_1-9_EN(U) 01.8.1, 9:43 AM5

CONTROLS AND FUNCTIONS

TRANSMIT

RE-NAME

STANDBY

6CH INPUT

SOUND

SYSTEM

CLEAR LEARN MACRO

OFF ON

MACRO

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

PARAMETER

SET MENU

EFFECT

LEVEL

ON SCREEN

TESTSLEEP

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AU X

POWER

100

11 12

234

Remote Control

This section describes the controls and their functions of

the remote control. See “REMOTE CONTROL

FEATURES” on pages 42 to 54 for operating other

components with this remote control.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 RE-NAME

Used for changing the input source name in the display

window (see page 47).

3 TRANSMIT indicator

Flashes while the remote control is sending signals.

4 STANDBY

Sets this unit in the standby mode.

5 SYSTEM POWER

Turns on the power of this unit.

6 Display window

Shows the selected source component that you are

controlling.

7 SOURCE SELECT k/n

Selects the another component to control independently

from the input that has been selected by pressing an input

selector button.

8 10KEY/DSP

Selects the numeric button (10KEY) mode or DSP mode.

9 Operation buttons

Provides functions such as play, stop, skip, etc. for

operating your other components selected by the input

selector buttons.

0 6.1/ES

Turns on or off the Dolby Digital Matrix 6.1 or DST ES

decoder with 10 KEY/DSP set to the DSP position.

q LEVEL

Selects the effect speaker channel to be adjusted and sets

the level.

w ON SCREEN

Selects the on-screen display (OSD) mode for your video

monitor.

e SLEEP

Sets the sleep timer.

r TEST

Outputs the test tone to adjust the speaker levels.

t CLEAR

Used for clearing functions acquired when using the learn

and rename features, and set manufacturer codes (see

page 47).

y LEARN

Used for setting up the manufacturer code or for

programming the functions of other remote controls (see

pages 43 and 44).

0102V2200_1-9_EN(U) 01.8.1, 9:43 AM6

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

BASS

VOLUMEINPUT

INPUT M0DE

VIDEO AUXSILENT

PROGRAM

STEREO

SPEAKERS

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

STANDBY

NATURAL SOUND AV RECEIVER

6CH INPUT

– +

TREBLE

– +

PRO LOGIC

DIGITAL

REC OUT/ZONE 2

V-AUX

VCR2

/DVR

VCR1

PHONO

TUNER

MD/TAPE

DVD

SOURCE

/REMOTE

D-TV/LD

CBL/SAT

CD-R

30°30°

Approximately 6 m (20 feet)

u MACRO

Used to program a series of operations for control by a

single button (see page 46).

i MACRO ON/OFF

Turns the macro function on and off.

o Å and ı

Switch the control area for the extra components that are

not connected to this unit without changing the input.

p Input selector buttons

Select the input source and change the control area.

a 6CH INPUT

Selects the source connected to the 6CH INPUT jacks.

s DSP program/Numeric buttons

Select DSP programs or numbers according to the

position of 10KEY/DSP.

d MUTE

Mutes the sound. The MUTE indicator turns on when the

MUTE function is on. Press again to restore the audio

output to the previous volume level.

f VOLUME +/–

Increases or decreases the volume level.

g STEREO/EFFECT

Switches the normal stereo or DSP effect reproduction.

When STEREO is selected, 2-channel input signals are

directed to the main left and right speakers without effect

sounds. All Dolby Digital and DTS audio signals except

for the LFE channel are also directed to the main left and

right speakers.

h PARAMETER/SET MENU

Selects the PARAMETER mode or SET MENU mode.

j Cursor buttons k/n/–/+

Select and adjust DSP program parameters and SET

MENU items according to the position of PARAMETER/

SET MENU.

Using the Remote Control

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the main unit during operation.

■ Handling the remote control

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– high humidity or temperature such as near a heater,

stove or bath;

– dusty places; or

– in places subject to extremely low temperatures.

0102V2200_1-9_EN(U) 01.8.1, 9:43 AM7

CONTROLS AND FUNCTIONS

LCR

RC RR

LFE

VIRTUAL

DTS

Neo

MOVIE THEATER

ENTERTAINMENT12

DOLBY DIGITAL

PRO

LOGIC

VCR DVD TUNER CD

PHONO

CD RV AUX

DSP

DISCRETE

PCM

SILENT

DIGITAL

VCR2/DVR

CBL

SAT

TAPE

STEREO

TUNED

MEMORY

P. DIRECT

BASS

MUTE VOLUME

SLEEP

AUTO

6.1

PRO LOGIC

78 q wertyui

123456

1 Processor indicators

When any function of DSP, DTS, DISCRETE,

VIRTUAL, g, 6.1/ES, and

PRO LOGIC

activated, its indicator lights up.

2 Input source indicator

Shows the current input source with underneath.

3 AUTO indicator

Shows that this unit is in the automatic tuning mode.

4 SLEEP indicator

Lights up while the sleep timer is on.

5 MUTE indicator

Lights up while the MUTE function is on.

6 VOLUME level indicator

Indicates the volume level.

7 v indicator

Lights up when this unit is reproducing PCM (pulse code

modulation) digital audio signals.

8 Headphones indicator

Lights up when headphones are connected.

9 SP A B indicator

Lights up according to which set of main speakers is

selected. Both indicators light up when both sets of

speakers are selected.

0 SILENT indicator

Lights up when headphones are connected with the sound

effect (see “SILENT CINEMA DSP” on page 30).

q DSP program indicators

The name of the selected DSP program lights up when

the ENTERTAINMENT, MOVIE THEATER 1, MOVIE

THEATER 2 or V/DTS SURROUND DSP program is

selected.

w Multi-information display

Shows the current DSP program name and other

information when adjusting or changing settings.

e STEREO indicator

Lights up when this unit is receiving a strong signal for an

FM stereo broadcast while the “AUTO” indicator is lit.

r TUNED indicator

Lights up when this unit tunes in to a station.

t MEMORY indicator

Flashes to show a station can be stored.

y BASS indicator

Lights up while BASS EXTENSION is on.

u P. DIRECT

Lights up while PROCESSOR DIRECT is on.

i Input channel indicator

Indicates the channel components of input signals being

received.

Front Panel Display

0102V2200_1-9_EN(U) 01.8.4, 3:08 PM8

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

AC OUTLETS

CENTER

SUB

WOOFER

S VIDEO

MONITOR OUT

VIDEO

DIGITAL OUTPUT

DIGITAL INPUT

6CH INPUT

GND

AUDIO AUDIO VIDEO

CONTROL OUT SPEAKERS

TUNER

REMOTE

75Ω UNBAL.

OUT

ANT

GND

ANT

+12V

10mA

MAX.

COMPONENT VIDEO

S VIDEO

DVD

D-TV

/LD

CBL

/SAT

VIDEO

PR/ CR

DVD

MONITOR

OUT

D-TV / LD

MAIN

REAR

CENTER

OUTPUT

IMPEDANCE SELECTOR

SET BEFORE POWER ON

SUB

WOOFER

CENTER

REAR

CENTER

REAR

PB/ CB Y

OPTICAL

TAPE

(

PLAY

)

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD-R

DVD

D-TV

PHONO

OUT

ZONE 2 OUT

VCR 2

/DVR

VCR 1

MAIN

SURROUND

/LD

CBL

/SAT

(SURROUND)

COAXIAL

–

MAIN A OR B:

A+B:

CENTER

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

6ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

16ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

REAR

REAR CENTER

MAIN A OR B:

A+B:

CENTER

REAR

REAR CENTER

AC IN

9 0 w e rq

(U.S.A. model)

1 DIGITAL OUTPUT jacks

2 Audio component jacks

See pages 16 and 17 for connection information.

3 Video component jacks

See pages 14 and 15 for connection information.

4 REMOTE IN/OUT jacks

See page 68 details.

5 OUTPUT jacks

See page 18 for connection information.

6 AC INLET (U.S.A. and Canada models only)

Use this inlet to plug in the supplied power cord.

7 AC OUTLET(S)

Use these outlets to supply power to your other A/V

components (see page 19).

8 DIGITAL INPUT jacks

9 6CH INPUT jacks

See page 18 for connection information.

0 ZONE 2 OUT jacks

See page 68 for details.

q Antenna input terminals

See page 36 for connection information.

w CONTROL OUT

This is a control expansion terminal for commercial use.

e Speaker terminals

See pages 11 and 12 for connection information.

r IMPEDANCE SELECTOR switch

Use this switch to match the amplifier output to your

speaker impedance (see page 13). Set this unit in the

standby mode before you change the setting of this

switch.

< China and General models only >

FREQUENCY STEP switch

See page 36.

VOLTAGE SELECTOR

See page 19.

*1 As this terminal is used for an examination in the factory, do not

connect any equipment to this terminal.

Rear Panel

0102V2200_1-9_EN(U) 01.8.1, 9:43 AM9

SPEAKER SETUP

Speakers to Be Used

This unit has been designed to provide the best sound-

field quality with a 6-speaker system, using left and right

main speakers, left and right rear speakers, and a center

and rear center speakers. If you use different brands of

speakers (with different tonal qualities) in your system,

the tone of a moving human voice and other types of

sound may not shift smoothly. We recommend that you

use speakers from the same manufacturer or speakers

with the same tonal quality.

The main speakers are used for the main source sound

plus the effect sounds. They will probably be the speakers

from your present stereo system. The rear speakers are

used for the effect and surround sounds, and the center

speaker is for the center sounds (dialog, vocals, etc.). If

for some reason it is not practical to use a center speaker,

you can do without it. Best results, however, are obtained

with the full system.

The main speakers should be high-performance models

and have enough power-handling capacity to accept the

maximum output of your audio system. The other

speakers do not have to be equal to the main speakers. For

precise sound localization, however, it is ideal to use the

models of equivalent performance with the main

speakers.

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the

addition of a subwoofer. The use of a subwoofer is

effective not only for reinforcing bass frequencies from

any or all channels, but also for reproducing the LFE

(low-frequency effect) channel with high fidelity when

the Dolby Digital signal or the DTS signal is played back.

The YAMAHA Active Servo Processing Subwoofer

System is ideal for natural and lively bass reproduction.

PREPARATION

Speaker Placement

Refer to the following diagram when you place the

speakers.

■ Main speakers

Place the left and right main speakers an equal distance

from the ideal listening position. The distance of each

speaker from each side of the video monitor should be the

same.

■ Center speaker

Align the front face of the center speaker with the front

face of your video monitor. Place the speaker as close to

the monitor as possible, such as directly over or under the

monitor and centrally between the main speakers.

Note

• If the center speaker is not used, the center channel sound will

be heard from the left and right main speakers. In this case,

“1A CENTER SP” on the SET MENU is set to NONE (see

page 56 for details).

■ Rear speakers

Place these speakers behind your listening position,

facing slightly inwards, nearly 1.8 m (6 feet) above the

floor.

■ Rear center speaker

Place the rear center speaker in the center between the left

and right rear speakers at the same height from the floor

as the rear speakers.

■ Subwoofer

The position of the subwoofer is not so critical, because

low bass sounds are not highly directional. But it is better

to place the subwoofer near the main speakers. Turn it

slightly toward the center of the room to reduce the wall

reflections.

CAUTION

Use magnetically shielded speakers. If this type of

speakers still creates the interference with a monitor,

place the speakers away from the monitor.

Main

speaker (L)

1.8 m (6 feet)

Rear speaker (L)

Rear center

speaker

Rear speaker (R)

Subwoofer

Main speaker (R)Center speaker

0103V2200_10-18_EN(U) 01.8.1, 9:43 AM10

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

Connecting the Speakers

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

CAUTION

• Use speakers with the specified impedance shown on the rear panel of this unit.

• Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could

damage this unit and/or speakers.

If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers

in your configuration after you finish connecting your speakers.

■ Speaker cables

A speaker cord is actually a pair of insulated cables

running side by side. One of the cables is colored or

shaped differently, perhaps with a stripe, groove or ridge.

1 Remove approximately 10 mm (3/8”) of

insulation from each of the speaker cables.

2 Twist the exposed wires of the cable

together to prevent short circuits.

■ Connecting to the SPEAKERS terminals

1 Unscrew the knob.

2 Insert one bare wire into the hole in the side

of each terminal.

3 Tighten the knob to secure the wire.

(U.S.A., Canada, Australia, China and General models only)

• Banana plug connections are also possible. First, tighten the

knob and then insert the banana plug connector into the end of

the corresponding terminal.

10 mm (3/8”)

■ MAIN SPEAKERS terminals

One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either

of the MAIN A or B terminals.

■ REAR SPEAKERS terminals

A rear speaker system can be connected to these terminals.

■ CENTER SPEAKER terminals

A center speaker can be connected to these terminals.

■ REAR CENTER SPEAKER terminals

A rear center speaker can be connected to these terminals.

Red: positive (+)

Black: negative (–)

Banana plug

0103V2200_10-18_EN(U) 01.8.1, 9:43 AM11

SPEAKER SETUP

AC OUTLETS

CENTER

SUB

WOOFER

S VIDEO

MONITOR OUT

VIDEO

DIGITAL OUTPUT

DIGITAL INPUT

6CH INPUT

GND

AUDIO AUDIO VIDEO

CONTROL OUT SPEAKERS

TUNER

REMOTE

75Ω UNBAL.

OUT

ANT

GND

ANT

+12V

10mA

MAX.

COMPONENT VIDEO

S VIDEO

DVD

D-TV

/LD

CBL

/SAT

VIDEO

/ C

DVD

MONITOR

OUT

D-TV / LD

MAIN

REAR

CENTER

OUTPUT

IMPEDANCE SELECTOR

SET BEFORE POWER ON

SUB

WOOFER

CENTER

REAR

CENTER

REAR

/ C

OPTICAL

TAPE

(

PLAY

)

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD-R

DVD

D-TV

PHONO

OUT

ZONE 2 OUT

VCR 2

/DVR

VCR 1

MAIN

SURROUND

/LD

CBL

/SAT

(SURROUND)

COAXIAL

–

MAIN A OR B:

A+B:

CENTER

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

6ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

16ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

REAR

REAR CENTER

MAIN A OR B:

A+B:

CENTER

REAR

REAR CENTER

AC IN

4567

Subwoofer

system

Rear Center

speaker

Main B speaker

Center

speaker

(U.S.A. model)

Right

Rear speaker

■ SUBWOOFER jack

When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System,

connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or

rear channels are directed to this jack if they are assigned to this jack. (The cut-off frequency of this jack is 90 Hz.) The

LFE (low-frequency effect) signals generated when Dolby Digital or DTS is decoded are also directed if they are

assigned to this jack.

Notes

• Adjust the volume level of the subwoofer with the control on the subwoofer. It is also possible to adjust the volume level by using the

remote control of this unit (see ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS on page 66).

• Depending on the settings of “1 SPEAKER SET” and “10 LFE LEVEL” on the SET MENU, some signals may not be output from

the SUBWOOFER jack.

Right Left

Main A speaker

Right Left

Left

The diagram above shows the speaker layout in the

listening room.

0103V2200_10-18_EN(U) 01.8.1, 9:43 AM12

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

AC OUTLETS

AC IN

SET BEFORE POWER ON

MAIN A OR B:

A+B:

CENTER

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

6ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

16ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

REAR CENTER

MAIN A OR B:

A+B:

CENTER

REAR

REAR CENTER

IMPEDANCE SELECTOR

REAR

8ΩMIN. /SPEAKER

16ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

MAIN A OR B:

A+B:

CENTER

REAR

REAR CENTER

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MAIN A OR B:

A+B:

CENTER

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

6ΩMIN. /SPEAKER

REAR

REAR CENTER

Switch

position

Left

Right

Speaker

Main

Center

Rear

Center

Rear

Main

Center

Rear

Center

Rear

Impedance level

If you use one set of main speakers, the impedance of

each speaker must be 4 Ω or higher.

If you use two sets of main speakers, the impedance of

each speaker must be 8 Ω or higher.

The impedance must be 6 Ω or higher.

The impedance of each speaker must be 6 Ω or higher.

If you use one set of main speakers, the impedance of

each speaker must be 8 Ω or higher.

If you use two sets of main speakers, the impedance of

each speaker must be 16 Ω or higher.

[Canada model only]

The impedance of each speaker must be 8 Ω or higher.

The impedance must be 8 Ω or higher.

The impedance of each speaker must be 8 Ω or higher.

IMPEDANCE

SELECTOR

switch

(U.S.A. model)

■ IMPEDANCE SELECTOR switch

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise this unit

may be damaged.

If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR

switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the

standby mode.

Select the left and right position according to the impedance of the speakers in your system. Be sure to move this switch

only when this unit is in the standby mode.

0103V2200_10-18_EN(U) 01.8.1, 9:43 AM13

CONNECTIONS

Before Connecting Components

CAUTION

Never connect this unit and other components to mains power until all connections between components have been

completed.

• Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some

components require different connection methods and have different jack names. Refer to the operation instructions

for each component to be connected to this unit.

• When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or

changer), connect them to the jack with the same number labels as !, #, $ etc. YAMAHA applies this labeling

system to all its products.

• After you have completed all connections, check them again to make sure they are correct.

Connecting Video Components

■ About the video jacks

There are three types of video jacks. Video signals input through the VIDEO jacks are the conventional composite video

signals. Video signals input through the S VIDEO jacks are separated into luminance (Y) and color (C) video signals.

The S-video signals achieve high-quality color reproduction. Video signals input through the COMPONENT VIDEO

jacks are separated into luminance (Y) and color difference (P

, P

) video signals. The jacks are also separated

into three for each signal. The description of the component video jacks may be different depending on the component

(e.g. Y, C

, C

/Y, P

, P

/Y, B-Y, R-Y etc.). Component video signals provide the best quality in picture reproduction.

If your video component has an S-video output or component video output, you can connect it to this unit. Connect the

S-video signal output jack on your video component to the S VIDEO jack or connect the component signal output jacks

on your video component to the COMPONENT VIDEO jacks.

• Each type of video jack works independently. Signals input through the composite

video, S-video and component jacks are output through the corresponding composite

video, S-video, and component jacks, respectively.

• You can designate the input for the COMPONENT VIDEO A and B jacks according

to your component by using “7 I/O ASSIGNMENT” on the SET MENU (see pages

61 and 62 for details).

Notes

• Use a commercially available S-video cable when connecting to the S VIDEO jack, and commercially available video cables when

connecting to the COMPONENT VIDEO jacks.

• When you are using the COMPONENT VIDEO jacks, check the details in the owner’s manual that came with the component being

connected.

■ VIDEO AUX jacks (on the front panel)

These jacks are used to connect any video input source

such as a game console and a camcorder to this unit.

S VIDEO VIDEO

L AUDIO R OPTICAL

VIDEO AUX

AUDIO OUT R

AUDIO OUT L

VIDEO OUT

OPTICAL OUT

S VIDEO OUT

Game console or camcorder

VIDEO

COMPONENT VIDEO

S VIDEO VIDEO

/ C

VIDEO jack

(composite)

COMPONENT

VIDEO jacks

S VIDEO

jack

0103V2200_10-18_EN(U) 01.8.1, 9:43 AM14

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

CENTER

SUB

WOOFER

DIGITAL OUTPUT

DIGITAL INPUT

6CH INPUT

GND

AUDIO

TUNER

75Ω UNBAL.

ANT

GND

ANT

MAIN

SUB

WOOFER

OPTICAL

TAPE

(

PLAY

)

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD-R

PHONO

MAIN

SURROUND

–

COAXIAL

CBL

/SAT

AUDIO VIDEO

COMPONENT VIDEO

S VIDEO

DVD

D-TV

/LD

CBL

/SAT

VIDEO

/ C

DVD

MONITOR

OUT

D-TV / LD

/ C

OUT

VCR 2

/DVR

VCR 1

S VIDEO

MONITOR OUT

VIDEO

DVD

/LD

D-TV

CONTROL OUT

REMOTE

OUT

+12V

10mA

MAX.

ZONE 2 OUT

S VIDEO

OUTPUT

S VIDEO

OUTPUT

S VIDEO

OUTPUT

S VIDEO

INPUT

VIDEO

INPUT

S VIDEO

OUTPUT

AUDIO

OUTPUT

AUDIO

OUTPUT

AUDIO INPUT

AUDIO OUTPUT

COAXIAL

OUTPUT

OPTICAL

OUTPUT

OPTICAL

OUTPUT

VIDEO

OUTPUT

VIDEO

OUTPUT

AUDIO

OUTPUT

VIDEO

OUTPUT

INPUT

VIDEO

OUTPUT

VIDEO

INPUT

COMPONENT

INPUT

COMPONENT

OUTPUT

COMPONENT

OUTPUT

S VIDEO

INPUT

(U.S.A. model)

LD player

demodulator

*1 If your LD player has an RF

OUTPUT jack, first connect it to

the RF INPUT on an RF

demodulator and then connect

the RF OUTPUT on an RF

demodulator to the COAXIAL

jack on this unit.

indicates S-video cables

indicates video cables

indicates coaxial cables

indicates optical cables

indicates right analog cables

indicates left analog cables

indicates signal direction

Video monitor

VCR 1 or VCR 2/

DVR (digital

video recorder)

Cable TV or

Satellite tuner

DVD player

TV/digital TV or

LD player

0103V2200_10-18_EN(U) 01.8.1, 9:43 AM15

CONNECTIONS

Connecting Audio Components

■ Connecting to digital jacks

This unit has digital jacks for direct transmission of

digital signals through either coaxial or fiber optic cables.

You can use the digital jacks to input PCM, Dolby Digital

and DTS bitstreams. When you connect components to

both the COAXIAL and OPTICAL jacks, priority is given

to the input signals from the COAXIAL jack. All digital

input jacks are acceptable for 96-kHz sampling digital

signals (see page 27 for details).

• You can designate the input for each digital jacks according to

your component by using “7 I/O ASSIGNMENT” on the SET

MENU (see pages 61 and 62 for details).

Note

• The OPTICAL jacks on this unit conform to the EIA standard.

If you use a fiber optic cable that does not conform to this

standard, this unit may not function properly.

■ Connecting a turntable

PHONO jacks are for connecting a turntable with an MM

or high-output MC cartridge. If you have a turntable with

a low-output MC cartridge, use an in-line boosting

transformer or MC-head amplifier when connecting to

these jacks.

• Connect your turntable to the GND terminal to reduce noise in

the signal. However you may hear less noise without the

connection to the GND terminal for some record players.

■ Connecting a CD player

• The COAXIAL CD and OPTICAL CD jacks are available for a

CD player which has coaxial or optical digital output jacks.

• When you connect a CD player to both the COAXIAL CD and

OPTICAL CD jacks, priority is given to the input signals from

the COAXIAL CD jack.

■ Connecting an MD recorder, tape

deck or CD recorder

• DIGITAL OUTPUT jacks and analog OUT (REC) are

independent. Only digital signals are output from DIGITAL

OUTPUT jacks and analog signals from OUT (REC) jacks.

• When you connect your recording component to both the

analog and digital input and output jacks, the priority is given

to the digital signal.

Notes

• When you connect a recording component to this unit, keep its

power on while using this unit. If the power is off, this unit may

distort the sound from other components.

• When you record from a source component connected to this

unit while this unit is set in the standby mode, the recorded

sound may be distorted. To avoid this problem, turn on this

unit.

0103V2200_10-18_EN(U) 01.8.1, 9:43 AM16

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

S VIDEO

MONITOR OUT

VIDEO

DIGITAL OUTPUT

DIGITAL INPUT

AUDIO VIDEO

CONTROL OUT

TUNER

REMOTE

75Ω UNBAL.

OUT

ANT

GND

ANT

+12V

10mA

MAX.

COMPONENT VIDEO

S VIDEO

DVD

D-TV

/LD

CBL

/SAT

VIDEO

/ C

DVD

MONITOR

OUT

D-TV / LD

/ C

OPTICAL

TAPE

CD-R

DVD

D-TV

OUT

ZONE 2 OUT

VCR 2

/DVR

VCR 1

/LD

CBL

/SAT

COAXIAL

GND

(

PLAY

)

AUDIO

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

PHONO

MAIN

SURROUND

CENTER

SUB

WOOFER

6CH INPUT

OUTPUT

GND

L R

INPUT OUTPUT INPUTOUTPUT

OUTPUT

COAXIAL

OUTPUT

OPTICAL

OUTPUT

OPTICAL

INPUT

OPTICAL

INPUT

OPTICAL

OUTPUT

SUBWOOFER

OUTPUT

CENTER

OUTPUT

MAIN

OUTPUT

SURROUND

OUTPUT

L R

(U.S.A. model)

indicates coaxial cables

indicates optical cables

indicates right analog cables

indicates left analog cables

indicates signal direction

External decoder

See page 18

Turntable

CD player

CD recorder

MD recorder or

tape deck

0103V2200_10-18_EN(U) 01.8.1, 9:43 AM17

CONNECTIONS

MAIN

OUTPUT

SUB

WOOFER

CENTER

REAR

(SURROUND)

4 5

Connecting to an External

Amplifier

If you want to increase the power output to the speakers,

or want to use another amplifier, connect an external

amplifier to the OUTPUT jacks as follows.

Note

• When RCA pin plugs are connected to the OUTPUT jacks for

output to an external amplifier, it is not necessary to use the

corresponding SPEAKERS terminals.

1 MAIN jacks

Main channel line output jacks.

Note

• The signals output through these jacks are affected by the

BASS, TREBLE and BASS EXTENSION settings.

2 REAR (SURROUND) jacks

Rear channel line output jacks.

3 SUBWOOFER jack

When using a subwoofer with built-in amplifier, including

the YAMAHA Active Servo Processing Subwoofer

System, connect the input jack of the subwoofer system

to this jack. Low bass signals distributed from the main,

center and/or rear channels are directed to this jack if they

are assigned to this jack. (The cut-off frequency of this

jack is 90 Hz.) The LFE (low-frequency effect) signals

generated when Dolby Digital or DTS is decoded are also

directed if they are assigned to this jack.

Notes

• Adjust the volume level of the subwoofer with the control on

the subwoofer. It is also possible to adjust the volume level by

using the remote control of this unit (see ADJUSTING THE

LEVEL OF THE EFFECT SPEAKERS on page 66).

• Depending on the settings of “1 SPEAKER SET” and “10 LFE

LEVEL” on the SET MENU, some signals may not be output

from the SUBWOOFER jack.

4 CENTER jack

Center channel line output jack.

5 REAR CENTER jack

Rear center channel line output jack.

Connecting an External Decoder

This unit is equipped with 6 additional input jacks (left

and right MAIN, CENTER, left and right SURROUND

and SUBWOOFER) for discrete multi-channel input from

an external decoder, sound processor or pre-amplifier.

Connect the output jacks on your external decoder to the

6CH INPUT jacks. Be sure to match the left and right

outputs to the left and right input jacks for the main and

surround channels.

Notes

• When you select 6CH INPUT as the input source, this unit

automatically turns off the digital sound field processor, and

you cannot listen to DSP programs.

• When you select 6CH INPUT as the input source, settings of

“1 SPEAKER SET” on the SET MENU do not apply (except

for 1F MAIN LEVEL).

0103V2200_10-18_EN(U) 01.8.1, 9:43 AM18

English

INTRODUCTION

PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

Connecting the Power Supply Cords

■ Connecting the AC power cord

[U.S.A. and Canada models]

Plug the power cord into the AC inlet when all

connections are complete, and then plug in this unit to the

wall outlet.

Caution

• Do not use other AC power cords than the one provided.

Otherwise it may result in causing fire or an electrical

shock.

[Australia, China and General models]

Plug in this unit to the wall outlet.

■ AC OUTLET(S) (SWITCHED)

U.S.A., Canada, China and

General models ............................................ 2 OUTLETS

Australia model .............................................. 1 OUTLET

Use these outlets to connect the power cords from your

components to this unit. The power to the AC

OUTLET(S) is controlled by this unit’s STANDBY/ON

(or SYSTEM POWER and STANDBY). These outlets

will supply power to any connected component whenever

this unit is turned on. The maximum power (total power

consumption of components) that can be connected to the

AC OUTLET(S) is 80 W.

■ VOLTAGE SELECTOR

(China and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE

plugging into the AC main supply. Voltages are 110/120/

220/240 V AC, 50/60 Hz.

(U.S.A. model)

AC IN

8ΩMIN. /SPEAKER

16ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

MAIN A OR B:

A+B:

CENTER

REAR

REAR CENTER

PEDANCE SELECTOR

ET BEFORE POWER ON

MAIN A OR B:

A+B:

CENTER

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

6ΩMIN. /SPEAKER

REAR

REAR CENTER

AC OUTLETS

To AC outlet

AC OUTLETS

8ΩMIN. /SPEAKER

16ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

MAIN A OR B:

A+B:

CENTER

REAR

REAR CENTER

PEDANCE SELECTOR

ET BEFORE POWER ON

MAIN A OR B:

A+B:

CENTER

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

6ΩMIN. /SPEAKER

REAR

REAR CENTER

VOLTAGE SELECTOR

(China and General models)

0104V2200_19-24_EN(U) 01.8.1, 9:43 AM19

CONNECTIONS

Turning on the Power

When all connections are completed, turn on the power of

this unit.

1 Press STANDBY/ON (SYSTEM POWER on

the remote control) to turn on the power of

this unit.

The level of the main volume, and then the current

DSP program name appear on the front panel

display.

2 Turn on the video monitor connected to this

unit.

Same information as above appears on the video

monitor, if the full or short display mode has been

selected.

BASS

VOLUMEINPUT

INPUT M0DE

VIDEO AUXSILENT

PROGRAM

STEREO

SPEAKERS

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

NATURAL SOUND AV RECEIVER

6CH INPUT

– +

TREBLE

– +

PRO LOGIC

REC OUT/ZONE 2

V-AUX

VCR2

/DVR

VCR1

PHONO

TUNER

MD/TAPE

DVD

SOURCE

/REMOTE

D-TV/LD

CBL/SAT

CD-R

DIGITAL

STANDBY

TRANSMIT

RE-NAME

STANDBY

6CH INPUT

SOUND

SYSTEM

CLEAR LEARN MACRO

OFF ON

MACRO

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAUSESTOPPOWER

REC

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AU X

POWER

STANDBY

/ON

SYSTEM

POWER

Remote control

Front panel

0104V2200_19-24_EN(U) 01.8.1, 9:43 AM20

English

INTRODUCTION

PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

Selecting the OSD Mode

1 Turn on the video monitor connected to this

unit.

2 Press ON SCREEN on the remote control

repeatedly to change the display mode.

The OSD mode changes in the following order: full

display, short display, and display off.

Notes

• If you choose a video input source that has a component

connected to both the S VIDEO IN and composite VIDEO IN

jacks, and both the S VIDEO OUT and composite VIDEO

OUT jacks are connected to a video monitor, the video signal is

output to both the S VIDEO OUT and VIDEO OUT jacks.

However, the OSD is carried only on the S-video signal. If no

video signal is input, the OSD is carried on both the S-video

and composite video signals.

• If your video monitor is connected only to the COMPONENT

VIDEO jacks of this unit, the OSD is not shown. Make sure to

connect your video monitor to the COMPONENT VIDEO

jacks and either VIDEO or S VIDEO jacks if you want to see

the OSD.

• Playing back video software that has an anti-copy signal or

video signals with a lot of noise may produce unstable images.

P01 CONCERT HALL 1

ROOM SIZE…………1.O

LIVENESS…………………5

INIT.DLY…………30ms

P01 CONCERT HALL 1

PARAMETER

SET MENU

LEVEL

ON SCREEN

TESTSLEEP

ON-SCREEN DISPLAY (OSD)

You can display the operation information for this unit on

a video monitor. If you display the SET MENU and DSP

program parameter settings on a monitor, it is much easier

to see the available options and parameters than it is by

reading this information on the front panel display.

• If a video source is being reproduced, the OSD is

superimposed over the image.

• The OSD signal is not output to the REC OUT jack, and will

not be recorded with any video signal.

• You can set the OSD to turn on (blue background) or off when

a video source is not being reproduced (or the source

component is turned off) by using “13 DISPLAY SET” on the

SET MENU (see page 65).

OSD Modes

You can change the amount of information the OSD

shows.

Full display

This mode always shows the DSP program parameter

settings on the video monitor (see page 71).

Short display

This mode briefly shows the same contents as the front

panel display at the bottom of the screen and then

disappears.

Display off

This mode briefly shows the “DISPLAY OFF” message at

the bottom of the screen and then disappears. Afterwards,

no changes to operations appear on the monitor except

those of the ON SCREEN button.

Full display Short display

• When you choose the full display mode, INPUT l / h,

VOLUME and some other types of operation information are

displayed at the bottom of the screen in the same format as that

for the front panel display.

• The SET MENU and test tone display appear regardless of the

OSD mode.

0104V2200_19-24_EN(U) 01.8.1, 9:43 AM21

Item

1A CENTER SP

1B MAIN SP

1C REAR L/R SP

1D REAR CT SP

1E LFE/BASS OUT

1F MAIN LEVEL

Description

Selects the output mode according to whether or not a center speaker is

being used and its performance.

Selects the output mode according to the performance of the main

speakers.

Selects the output mode according to whether or not rear L/R speakers

are being used and their performance.

Selects the Rear Center channel output according to the size of the Rear

Center speaker.

Selects the speaker according to use for LFE signal output and low bass

signal.

Selects the main speaker level.

Control value (default

setting indicated in bold)

LRG/SML/NONE

LARGE/SMALL

LRG/SML/NONE

SWFR/MAIN/BOTH

Normal/–10 dB

SPEAKER MODE SETTINGS

This unit has 6 SPEAKER SET items on the SET MENU that you must set according to the number of speakers in your

configuration and their size. The following table summarizes these SPEAKER SET items, and shows the initial settings

as well as other possible settings.

Summary of SPEAKER SET Items 1A through 1F

If the initial settings shown in the above table are not appropriate for your speaker configuration,

change settings following the steps described in “1 SPEAKER SET” from page 56 to 59.

0104V2200_19-24_EN(U) 01.8.1, 9:43 AM22

English

INTRODUCTION

PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

4 Set PARAMETER/SET

MENU on the remote

control to PARAMETER.

Using the Test Tone (TEST DOLBY

SUR.)

Use the test tone to balance the output levels of the 6

speakers required for a surround sound system. The

adjustment of each speaker output level should be made at

your listening position with the remote control.

1 Press TEST to output the

test tone.

2 Adjust the volume so you can hear the test

tone.

The test tone is heard from the left main speaker,

center speaker, right main speaker, right rear speaker,

rear center speaker and left rear speaker in order. The

tone is produced for 2.5 seconds each time.

This section explains how to adjust the speaker output

levels by using the test tone generator. When this

adjustment is made, the output level heard at the listening

position will be the same from each speaker. This is

important for the best performance of the digital sound

field processor, and various decoders (Dolby Digital,

Dolby Pro Logic, Dolby Pro Logic

, DTS, DTS ES, and

DTS Neo: 6).

Note

• Since this unit cannot enter the test mode while headphones are

connected to this unit, be sure to unplug the headphones from

the PHONES jack when using the test tone.

Before You Begin

1 Turn on the video monitor connected to this

unit.

2 Press SPEAKERS A or B

to select the main

speakers to be used.

If you are using two sets of the

main speakers, press both A

and B.

3 Set the BASS and TREBLE controls on the

front panel to the center position and turn off

BASS EXTENSION and PROCESSOR

DIRECT by pressing the buttons.

“BASS EXT. OFF” and “P. DIRECT OFF” appear

on the front panel display.

TEST

BASS

–

TREBLE

–

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

PARAMETER

SET MENU

EFFECT

LEVEL

ON SCREEN

TESTSLEEP

TV MUTE

A/B/C/D/E

31, 4

BASS

EXTENSION

PROCESSOR

DIRECT

SPEAKERS

ADJUSTING THE SPEAKER OUTPUT LEVELS

Set to OFF.

BASS

VOLUMEINPUT

INPUT M0DE

VIDEO AUXSILENT

PROGRAM

STEREO

SPEAKERS

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

NATURAL SOUND AV RECEIVER

6CH INPUT

– +

TREBLE

– +

PRO LOGIC

REC OUT/ZONE 2

V-AUX

VCR2

/DVR

VCR1

PHONO

TUNER

MD/TAPE

DVD

SOURCE

/REMOTE

D-TV/LD

CBL/SAT

CD-R

DIGITAL

STANDBY

BASS

VOLUMEINPUT

INPUT M0DE

VIDEO AUXSILENT

PROGRAM

STEREO

SPEAKERS

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

NATURAL SOUND AV RECEIVER

6CH INPUT

– +

TREBLE

– +

PRO LOGIC

REC OUT/ZONE 2

V-AUX

VCR2

/DVR

VCR1

PHONO

TUNER

MD/TAPE

DVD

SOURCE

/REMOTE

D-TV/LD

CBL/SAT

CD-R

DIGITAL

STANDBY

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

PARAMETER

SET MENU

EFFECT

LEVEL

ON SCREEN

TESTSLEEP

TV MUTE

A/B/C/D/E

PARAMETER

SET MENU

VOLUME

Front panel

Remote control

0104V2200_19-24_EN(U) 01.8.1, 9:43 AM23

ADJUSTING THE SPEAKER OUTPUT LEVELS

Notes

• The tonal quality of the center speaker can be adjusted by using

“5 CENTER GEQ” on the SET MENU (see page 60).

• If “1A CENTER SP” on the SET MENU is set to NONE, the

center channel sound is automatically output from the left and

right main speakers.

• If “1C REAR L/R SP” on the SET MENU is set to NONE, the

output level of the rear right, left and center speakers cannot be

adjusted in step 3. The test tone will be circulated in the order

of LEFT→CENTER→RIGHT→LEFT..., skipping the rear right

and left speakers and the rear center speaker.

• If “1D REAR CT SP” on the SET MENU is set to NONE, the

out level of the rear center speaker cannot be adjusted in step 3.

The test tone will be circulated in the order of

LEFT→CENTER→RIGHT→RIGHT SURROUND→LEFT

SURROUND→LEFT ..., skipping the rear center speaker.

• It is not necessary to readjust the speaker level once it is set as

long as you do not change the speakers. You can enjoy listening

to or watching the input source with the desired volume by

adjusting the volume key.

• You can increase the output levels of the effect speakers

(center, left rear and right rear and rear center) to +10 dB. If the

output level of these speakers is lower than that of the main

speakers even after you have increased the output level of these

speakers up to +10 dB, set “1F MAIN LEVEL” on the SET

MENU to –10 dB (see page 59). This setting decreases the

main speaker output level to about one-third of the normal

level. After you have set “1F MAIN LEVEL” on the SET

MENU to –10 dB, adjust the levels for the center and rear

speakers again.

The state of the test tone output is also shown on the

monitor by an image of the audio listening room.

This is convenient for adjusting each speaker level.

Front panel display also indicates from which

speaker the test tone is output in the order of TEST

LEFT→TEST CENTER→TEST RIGHT→

TEST R SUR.→TEST REAR CNTR→TEST L SUR.

Note

• If the test tone cannot be heard, turn down the volume, set this

unit in the standby mode and check the speaker connections.

3 Press –/+ repeatedly to

adjust the output level of

the effect speakers so that

the output level coming

from each speaker is the

same.

While adjusting, the test tone is heard from the

selected speaker.

• You can stop the sequence temporarily by holding down k / n.

4 When the adjustment is

complete, press TEST to

stop the test tone.

LEFT

TEST DOLBY SUR.

LEFT SURROUND RIGHT SURROUND

CENTER

REAR CENTER

RIGHT

LEFT

TEST

0104V2200_19-24_EN(U) 01.8.1, 9:43 AM24

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

BASIC PLAYBACK

1 Press STANDBY/ON (SYSTEM POWER on

the remote control) to turn on the power.

2 Turn on the video monitor connected to this

unit if you will play video sources.

3 Press SPEAKERS A or B

to select the main

speakers to be used.

If you are using two sets of

main speakers, press both A

and B. The speaker indicator(s)

for the selected set(s) lights up

on the front panel display.

4 Press INPUT l / h repeatedly (one of the

input selector buttons on the remote control)

to select the input source.

• The current input source name lights up on the

front panel display.

• The current input source name and input mode

appear on the front panel display and on the video

monitor for a few seconds.

To select a source connected to the 6CH INPUT

jacks

Press 6CH INPUT until “6CH INPUT” appears on the

front panel display and on the video monitor.

Notes

• If “6CH INPUT” is shown on the front panel display and on

the video monitor, no other source can be played. To select

another input source with INPUT l / h (one of the input

selector buttons), press 6CH INPUT to turn off “6CH INPUT”

from the front panel display and the video monitor.

• If you want to enjoy an audio source connected to the 6CH

INPUT jacks together with a video source, first select the video

source and then press 6CH INPUT.

INPUT

TRANSMIT

RE-NAME

STANDBY

6CH INPUT

SOUND

SYSTEM

CLEAR LEARN MACRO

OFF ON

MACRO

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

DSP

10KEY

HALL 2

CHURCH

JAZZ CLUB

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AU X

POWER

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

100

11 12

234

PHONO

DVD

VCR2/DVR

VCR 1

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

VCR DVD TUNER CD

PHONO

CD RV AUX 1

VCR2/DVR

CBL

SAT

TAPE

VOLUME

DVD AUTO

BASS

VOLUMEINPUT

INPUT M0DE

VIDEO AUXSILENT

PROGRAM

STEREO

SPEAKERS

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

NATURAL SOUND AV RECEIVER

6CH INPUT

– +

TREBLE

– +

PRO LOGIC

REC OUT/ZONE 2

V-AUX

VCR2

/DVR

VCR1

PHONO

TUNER

MD/TAPE

DVD

SOURCE

/REMOTE

D-TV/LD

CBL/SAT

CD-R

DIGITAL

STANDBY

464

STANDBY

/ON

SYSTEM

POWER

SPEAKERS

Remote control

Front panel

Selected input source

6CH INPUT

Remote controlFront panel

0105V2200_25-30_EN(U) 01.8.1, 9:43 AM25

BASIC PLAYBACK

■ BGV (background video) function

The BGV function allows you to combine a video image

from a video source with a sound from an audio source.

For example, you can enjoy listening to classical music

while having beautiful scenery from the video source on

the video monitor.

Select a source from the video group and then select a

source from the audio group with the input selector

buttons on the remote control. This selection for BGV

cannot be made with INPUT l / h on the front panel.

■ To mute the sound

Press MUTE on the

remote control.

To resume the audio output,

press MUTE again.

• You can also cancel mute to press any operation buttons such as

VOLUME +/–.

• During muting, the “MUTE” indicator flashes on the front

panel display and “MUTE ON” appears on the front panel

display for a few seconds.

■ When you have finished using

this unit

Press STANDBY/ON (STANDBY on the

remote control) to set this unit in the

standby mode.

5 Start playback or select a broadcast station

on the source component.

Refer to the operation instructions for the

component.

6 Adjust the volume to the desired output

level.

If desired, use BASS, TREBLE and BASS

EXTENSION etc. These controls are only effective

for sound from the main speakers.

Note

• If the component connected to the VCR 1 OUT, VCR 2/DVR

OUT, CD-R OUT and MD/TAPE OUT jacks is turned off, the

reproduced sound may be distorted or the volume may be

lowered for the characteristics of AV receivers. In this case,

turn on the component.

7 Select a DSP program if desired.

Use PROGRAM l / h (DSP program buttons on

the remote control) to select a DSP program. See

pages 31 to 35 for details about the DSP program.

PHONO

DVD

VCR2/DVR

VCR 1

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

VOLUME

BASS

–

TREBLE

–

BASS

EXTENSION

PROCESSOR

DIRECT

Front panel

Remote control

STANDBY

/ON

STANDBY

Front panel

Remote control

MUTE

PROGRAM

HALL 1

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

100

11 12

234

Front panel Remote control

0105V2200_25-30_EN(U) 01.8.1, 9:43 AM26

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

BASIC PLAYBACK

Input Modes and Indications

This unit comes with various input jacks. You can set the

priority of the input signal among different types of input

signals.

When you turn on the power of this unit, the input mode

is set according to “8 INPUT MODE” on the SET MENU

(see page 62 for details).

Press INPUT MODE (the input selector

button that you have pressed to select the

input source on the remote control)

repeatedly until the desired input mode is

shown on the front panel display and on the

video monitor.

AUTO: In this mode, the input signal is

automatically selected in the following

order:

1) Dolby Digital or DTS signal

2) Digital (PCM) signal

3) Analog signal

DTS: In this mode, only the digital input signal

encoded with DTS is selected even if

another signal is input at the same time.

ANALOG: In this mode, only the analog input signal is

selected even if a digital signal is input at

the same time.

Notes

• If digital signals are input from both the COAXIAL and

OPTICAL jacks, the digital signal from the COAXIAL jack

has precedence over the OPTICAL jack.

• When AUTO is selected, this unit automatically determines the

type of signal. If this unit detects a Dolby Digital or DTS

signal, the decoder automatically switches to the appropriate

setting.

• In playing the disc encoded with Dolby Digital or DTS on

some LD or DVD players, the sound output delays for a

moment when playback resumes after a search because the

digital signal is selected again.

• When playing the LD source that has not been digitally

recorded, the sound may not be output for some LD players. In

this case, set the input mode to ANALOG.

INPUT MODE

VCR DVD TUNER CD

PHONO

CD RV AUX 1

VCR2/DVR

CBL

SAT

TAPE

VOLUME

DVD AUTO

PHONO

DVD

VCR2/DVR

VCR 1

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

Remote controlFront panel

Input mode

■ Notes on the digital signal

The digital input jacks of this unit can also handle

96-kHz sampling digital signals. (To utilize this, use a

source that supports 96-kHz sampling digital signals and

set the player for digital output. Refer to the operation

instructions for the player.) Note the following when a 96-

kHz sampling digital signal is input to this unit:

– DSP programs cannot be selected. Sound will be output

as normal 2-channel stereo sound from only the left and

right main speakers.

Note

• If “1B MAIN SP” on the SET MENU is set to SMALL and

“1E LFE/BASS OUT” is set to SWFR, or “1E LFE/BASS

OUT” is set to BOTH, the sound is also output from the

subwoofer.

–“Adjusting the output level of the effect speakers”

described on page 66 cannot be made.

■ Notes on playing DTS-CD/LDs

• If the digital output data of the player has been

processed in any way, you may not be able to perform

DTS decoding even if you make a digital connection

between this unit and the player.

• If you play a source encoded with a DTS signal and

set the input mode to ANALOG, this unit reproduces

the noise of an unprocessed DTS signal. When you

want to play a DTS source, be sure to connect the

source to a digital input jack and set the input mode to

AUTO or DTS.

• If you switch the input mode to ANALOG while

playing a source encoded with a DTS signal, this unit

reproduces no sound.

• If you play a source encoded with a DTS signal with

the input mode set to AUTO;

– This unit automatically switches to the DTS-

decoding mode (The “t” indicator lights up.)

after having detected the DTS signal. When playback

of the DTS source is completed, the “t” indicator

may flash. While this indicator is flashing, only DTS

source can be played. If you want to play a normal

PCM source soon, set the input mode back to AUTO.

– The “t” indicator may flash when a search or

skip operation is performed while the DTS source is

playing back with the input mode set to AUTO. If

this status continues for longer than 30 seconds, this

unit will automatically switch from “DTS-decoding”

mode to PCM digital signal input mode. The “t”

indicator will turn off.

0105V2200_25-30_EN(U) 01.8.1, 9:43 AM27

BASIC PLAYBACK

Selecting a Sound Field Program

You can enhance your listening experience by selecting a

DSP program. There are 11 programs with sub-programs

available with this unit. However the selection depends on

the input signal format and not all the sub-programs are

possible for all input signal formats. For details about

each program, see pages 31 to 35.

1 Set 10KEY/DSP to DSP on

the remote control.

2 Press PROGRAM l / h (one of the DSP

program buttons on the remote control) to

select the desired program.

The name of the selected program appears on the

front panel display and on the video monitor.

BASS

VOLUMEINPUT

INPUT M0DE

VIDEO AUXSILENT

PROGRAM

STEREO

SPEAKERS

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

NATURAL SOUND AV RECEIVER

6CH INPUT

– +

TREBLE

– +

PRO LOGIC

REC OUT/ZONE 2

V-AUX

VCR2

/DVR

VCR1

PHONO

TUNER

MD/TAPE

DVD

SOURCE

/REMOTE

D-TV/LD

CBL/SAT

CD-R

DIGITAL

STANDBY

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

100

11 12

234

2,31

3 After selecting the desired program, press

the same button repeatedly to select the

desired sub-program if available.

For example, to select the sub-program “70 mm

Spectacle”, press MOVIE THEATER 1 repeatedly.

Notes

• Choose a DSP program based on your listening preference, and

not on the name of the program. The acoustics of your listening

room affect the DSP program. Minimize the sound reflections

in your room to maximize the effect created by the program.

• When you select an input source, this unit automatically selects

the last DSP program used with that source.

• When you set this unit in the standby mode, the current source

and DSP program are memorized and are automatically

selected when you turn on the power again.

• If a Dolby Digital or DTS signal is input when the input mode

is set to AUTO, the DSP program (No. 9–11) automatically

switches to the appropriate decoding program.

• When a monaural source is being played with PRO LOGIC/

Normal or PRO LOGIC/Enhanced, PRO LOGIC Movie, or

Neo: 6 Cinema, no sound will be heard from the main speakers

and the rear speakers. Sound can only be heard from the center

speaker. However, if “1A CENTER SP” on the SET MENU is

set to NONE, the center channel sound is output from the main

speakers.

• When a source connected to the 6CH INPUT jacks of this unit

is selected, the digital sound field processor cannot be used.

• When 96-kHz sampling digital signals are input to this unit, the

DSP program cannot be selected. In this case, the sound is

reproduced as normal 2-channel stereo.

MOVIE THEATER

VCR DVD TUNER CD

PHONO

CD RV AUX

DSP

VCR2/DVR

CBL

SAT

TAPE

VOLUME

PRO LOGIC

70mm Spectacle

PROGRAM

Sub-program name

Program name

Front panel

Remote control

MOVIE THEATER

VCR DVD TUNER CD

PHONO

CD RV AUX

DSP

VCR2/DVR

CBL

SAT

TAPE

VOLUME

PRO LOGIC

DGTL Spectacle

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

100

11 12

234

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

100

11 12

234

Program name

Sub-program name

DSP

10KEY

0105V2200_25-30_EN(U) 01.8.1, 9:43 AM28

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

BASIC PLAYBACK

(For remote control only)

3 Press the numeric button 12 repeatedly to

select the decoder; PRO LOGIC, PRO LOGIC

or Neo: 6.

The decoder selection switches from PRO LOGIC

to Neo: 6 and then returns to PRO LOGIC on the

front panel display.

4 After deciding on the decoder (PRO LOGIC

or Neo: 6), select the mode to suit the

source by pressing the numeric button 11.

The selection switches as follow;

PRO LOGIC

Movie ↔ PRO LOGIC Music

(when PRO LOGIC

is selected)

Neo: 6 Cinema ↔ Neo: 6 Music

(when Neo: 6 is selected)

■ Playing the Dolby Digital Matrix

6.1 or DTS ES software

Press 6.1/ES to turn on the Dolby Digital Matrix 6.1 or

DTS ES decoder to listen to the Dolby Digital Matrix 6.1

and DTS ES software with a rear center speaker.

The display changes AUTO → Disc6.1 → Mtrx6.1 →

OFF each time the ES/6.1 button is pressed.

Notes

• No sound will be output from the rear center speaker if you

have set “1C REAR L/R SP” on the SET MENU to NONE.

• The rear center speaker can be used when playing a 5.1-

channel source also.

Selecting PRO LOGIC or Neo: 6

You can enjoy the 2-channel sources decoded into five or

six discrete channels by selecting PRO LOGIC

or Neo:

6 in the program No. 11.

1 Select a 2-channel source and start playback

on the source component.

2 Select PRO LOGIC (Movie/Music) or Neo: 6

(Cinema/Music) by pressing PROGRAM l /

h on the front panel.

Select PRO LOGIC by pressing the numeric

button 11 on the remote control.

PRO

LOGIC

VCR DVD TUNER CD

PHONO

CD RV AUX

DSP

VCR2/DVR

CBL

SAT

TAPE

VOLUME

PRO LOGIC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

100

11 12

234

Remote control

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

100

11 12

234

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

100

11 12

234

BASS

VOLUMEINPUT

INPUT M0DE

VIDEO AUXSILENT

PROGRAM

STEREO

SPEAKERS

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

NATURAL SOUND AV RECEIVER

6CH INPUT

– +

TREBLE

– +

PRO LOGIC

REC OUT/ZONE 2

V-AUX

VCR2

/DVR

VCR1

PHONO

TUNER

MD/TAPE

DVD

SOURCE

/REMOTE

D-TV/LD

CBL/SAT

CD-R

DIGITAL

STANDBY

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

100

11 12

234

2,3,4

PROGRAM

Front panel

6.1/ES

CHP/INDEX

The “ c ” indicator lights up.

LCR

RC RR

MOVIE THEATER

VCR DVD TUNER CD

PHONO

CD RV AUX

DSP

DIGITAL

VCR2/DVR

CBL

SAT

TAPE

VOLUME

6.1

Spectacle 6.1

0105V2200_25-30_EN(U) 01.8.1, 9:43 AM29

BASIC PLAYBACK

■ Normal Stereo Reproduction

Press STEREO to turn off the sound effect

for normal stereo reproduction.

Press STEREO again to turn the sound effect back

on.

Notes

• If you turn off the sound effect, no sound is output from the

center speaker, rear speakers and rear center speaker.

• If you turn off the sound effect while a Dolby Digital or DTS

signal is being output, the dynamic range of the signal is

automatically compressed and the sounds of the center and rear

speaker channels are mixed and output from the main speakers.

• The volume may be greatly reduced when you turn off the

sound effect or if you set “11 D-RANGE” on the SET MENU

to MIN. In this case turn on the sound effect.

■ Displaying the information about

the input source

You can display the information such as the type, format

and sampling frequency of the signal input from the

component connected to this unit.

1 Select the input source you want to obtain

the information about by pressing an input

selector button.

2 Press STEREO to light

STEREO.

3 Press k/n to display the information about

the input signal.

AUTO: This mode automatically switches Dolby

Digital Matrix 6.1/DTS ES Matrix 6.1/DTS

ES Discrete 6.1 depending on the signal in

the input source that this unit can detect.

Rear center speaker does not work for 5.1

channel sources.

Disc6.1: This mode can be selected only when the

source with DTS ES Discrete format has

been detected.

Mtrx6.1: This mode makes 6-channel playback of the

input source through the Matrix 6.1 decoder.

OFF: Rear center speaker does not work in this

mode.

■ Virtual CINEMA DSP and SILENT

CINEMA DSP

Virtual CINEMA DSP

With the Virtual CINEMA DSP, you can enjoy all the

DSP programs without rear speakers. It creates the virtual

speakers to reproduce the natural sound field.

The sound field processing is changed to the Virtual

CINEMA DSP mode according to the selected DSP

program by setting “1C REAR L/R SP” on the SET

MENU to NONE.

Note

• This unit is not set in the virtual CINEMA DSP mode even if

“1C REAR L/R SP” is set to NONE in the following cases:

– when the 6ch Stereo, DOLBY DIGITAL Normal, Pro Logic

, DTS Normal or Neo: 6 program is selected;

– when the sound effect is turned off;

– when 6CH INPUT is selected as the input source;

– when 96-kHz sampling digital signals are input to this unit;

– when using the test tone; or

– when connecting the headphones.

SILENT CINEMA DSP

You can enjoy the powerful sound field as if there were

actual speakers with the SILENT CINEMA DSP. You can

listen to SILENT CINEMA DSP by connecting your

headphones to the PHONES jack while the digital sound

field processor is on. Enjoy all the DSP program using the

headphones. The “SILENT” indicator lights up on the

front panel display. (If the sound effect is off, you listen to

the source with normal stereo reproduction.)

Note

• This unit is not set in the SILENT CINEMA DSP mode even if

the sound effect is on;

– when 96-kHz sampling digital signals are input to this unit.

STEREO

EFFECT

STEREO

EFFECT

Front panel

Remote control

PHONO

DVD

VCR2/DVR

VCR 1

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

STEREO

EFFECT

PARAMETER

SET MENU

LEVEL

ON SCREEN

TESTSLEEP

0105V2200_25-30_EN(U) 01.8.1, 9:43 AM30

BASIC

OPERATION

English

INTRODUCTION PREPARATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

DIGITAL SOUND FIELD PROCESSING (DSP)

Understanding Sound Fields

A sound field is defined as the “characteristic sound reflections of a

particular space.” In concert halls and other music venues, we hear

early reflections and reverberations as well as the direct sound

produced by the artist(s). The variations in the early reflections and

other reverberations among the different music venues is what gives

each venue its special and recognizable sound quality.

YAMAHA sent teams of sound engineers all around the world to

measure the sound reflections of famous concert halls and music

venues, and collect detailed sound field information such as the

direction, strength, range, and delay time of those reflections. Then

we stored this enormous amount of data in the ROM chips of this

unit.

■ Recreating a sound field

Recreating the sound field of a concert hall or an opera house requires localizing the virtual sound sources in your

listening room. The traditional stereo system that uses only two speakers is not capable of recreating a realistic sound

field. YAMAHA’s DSP requires four effect speakers to recreate sound fields based on the measured sound field data.

The processor controls the strength and delay time of the signals output from the four effect speakers to localize the

virtual sound sources in a full circle around the listener.

Hi-Fi DSP Programs

The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in

mind that most of these are precise digital recreations of actual acoustic environments.

No.

Program

CONCERT HALL 1

CONCERT HALL 2

CHURCH

JAZZ CLUB

ROCK CONCERT

ENTERTAINMENT/

Disco

ENTERTAINMENT/

6ch Stereo

Features

This is a large fan-shaped concert hall which has approximately 2500 seats. Almost the whole

interior is made of wood. There is relatively little reflection from the walls, and sound spreads

finely and beautifully.

A large round concert hall with a rich surround effect. Pronounced reflections from all directions

emphasize the extension of sounds. The sound field has a great deal of presence, and your virtual

seat is near the center, close to the stage.

This program recreates the acoustic environment of a big church with a high dome and columns

along each side. The reverberation delay is very long while the early reflections are smaller than

with other sound field programs.

This is the sound field at stage front in “The Bottom Line”, a famous New York jazz club. The

floor can seat 300 people to the left and right in a sound field offering a real and vibrant sound.

The ideal program for lively, dynamic rock music. The data for this program was recorded at

LA’s “hottest” rock club. The listener’s virtual seat is at the center-left of the hall.

This program recreates the acoustic environment of a lively disco in the heart of a big city. The

sound is dense and highly concentrated. It is also characterized by a high-energy, “immediate”

sound.

Using this program increases the listening position range. This is a sound field suitable for

background music at parties.

0106V2200_31-35_EN(U) 01.8.1, 9:43 AM31

CINEMA-DSP

Sound Design of CINEMA-DSP

Filmmakers intend the dialog to be located right on the screen, the effect sound a little farther back, the music spread

even farther back, and the surround sound around the listener. Of course, all of these sounds must be synchronized with

the images on the screen.

CINEMA-DSP is an upgraded version of YAMAHA DSP specially designed for movie soundtracks. CINEMA-DSP

integrates the DTS, Dolby Digital, and Dolby Pro Logic surround sound technologies with YAMAHA DSP sound field

programs to provide the surround sound field. It recreates the most complete movie sound design in your audio room. In

CINEMA-DSP sound field programs, YAMAHA’s exclusive DSP processing is added to the right and left Main and

Center channels, so the listener can enjoy realistic dialogue, depth of sound, smooth transition between sound sources,

and a surround sound field that goes beyond the screen.

When a DTS or Dolby Digital signal is detected, the CINEMA-DSP sound field processor automatically chooses the

most suitable sound field program for that signal.

L SURROUND SOUND FIELD

R SURROUND SOUND FIELD

PRESENCE SOUND FIELD

DIALOG

EFFECT MUSIC

In addition to the DSP, this unit is equipped with various precise decoders; Dolby Pro Logic/Pro Logic /DTS Neo: 6

decoder for 2-channel sources, Dolby Digital/DTS decoder for multi-channel sources and Dolby Digital Matrix 6.1 or

DTS ES decoder for a rear center channel. You can select the CINEMA-DSP program to optimize these decoders and

the DSP sound patterns depending on the input source.

0106V2200_31-35_EN(U) 01.8.1, 9:44 AM32

English

INTRODUCTION PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CINEMA-DSP

The 6-channel soundtracks found on 70-mm film produce precise sound field localization and rich, deep sound without

using matrix processing. This unit’s MOVIE THEATER programs provide the same quality of sound and sound

localization that 6-channel soundtracks do. The built-in Dolby Digital or DTS decoder brings the professional-quality

sound designed for movie theaters into your home. With this unit’s MOVIE THEATER programs, you can recreate a

dynamic sound that gives you the feeling of being at a public theater in your listening room by using Dolby Digital or

DTS technology.

■ Dolby Digital/DTS + DSP sound field effect

These programs use YAMAHA’s tri-field DSP processing

on each of the Dolby Digital or DTS signals for the front,

left surround and right surround channels. This processing

enables this unit to reproduce the immense sound field

and surround expression of a Dolby Digital- or DTS-

equipped movie theater without sacrificing the clear

separation of all channels.

■ Dolby Digital Matrix 6.1/DTS ES + DSP sound field effect

These programs provide you with the maximum experience of the spacious surround effects since an extra rear center

DSP sound field created from the rear center channel is added.

■ Dolby Pro Logic + DSP sound field effect

Most movie software has 4-channel (left, center, right and

surround) sound information encoded by Dolby Surround

matrix processing and stored on the left and right tracks.

These signals are processed by the Dolby Pro Logic

decoder. The MOVIE THEATER programs are designed

to recreate the spaciousness and delicate nuances of

sound that tend to be lost in the encoding and decoding

processes.

■ Dolby Pro Logic /DTS Neo: 6

Dolby Pro Logic and DTS Neo: 6 equipped on this unit decode the 2-channel Dolby Surround software into five

discrete full-range channels (3 channels in front and 2 or 3 channels in rear). They also provide two modes; MOVIE/

CINEMA for movies and MUSIC for 2-channel source.

Surround DSP

sound field

Right surround DSP

sound field

Presence DSP

sound field

Left surround DSP

sound field

Presence DSP

sound field

0106V2200_31-35_EN(U) 01.8.1, 9:44 AM33

CINEMA-DSP

CINEMA-DSP Programs

■ For movie programs: No. 9 to 11

According to the input signal format, this unit automatically chooses the appropriate decoder and DSP sound field

pattern.

Table of Program Names for Each Input Format

MOVIE

THEATER 1

MOVIE

THEATER 2

DOLBY

DIGITAL

DTS DIGITAL

SUR

PRO LOGIC

DTS Neo: 6

2 channel

Stereo

70 mm Spectacle

70 mm Sci-Fi

70 mm Adventure

70 mm General

—

Normal

Enhanced

Movie

Music

Cinema

Music

DOLBY DIGITAL

DGTL Spectacle

DGTL Sci-Fi

DGTL Adventure

DGTL General

Normal

Enhanced

—

5.1 channel

DTS

DTS Spectacle

DTS Sci-Fi

DTS Adventure

DTS General

—

Normal

Enhanced

—

DTS ES

Spectacle ES

Sci-Fi ES

Adventure ES

General ES

—

ES Matrix 6.1

ES Discrete 6.1

Enhanced ES

—

6.1 channel *

Input

Program

DOLBY DIGITAL

Spectacle 6.1

Sci-Fi 6.1

Adventure 6.1

General 6.1

Matrix 6.1

Enhanced 6.1

—

*1 means the 6.1/ES decoder is ON.

*2 means the DTS ES software encoded with Discrete 6.1 is input.

• If a Dolby Digital signal or DTS signal is input when the input mode is set to AUTO, the DSP program will be automatically

switched to the Dolby Digital playback sound field or DTS playback sound field.

• If Dolby Digital Surround EX software or DTS ES software is played when AUTO is selected by pressing the 6.1/ES button on the

remote control, the Dolby Digital Matrix 6.1 or DTS ES decoder will automatically turn on and the corresponding DSP program will

be selected.

• 6.1/ES on the remote control can be used to play Dolby Digital or DTS 5.1 channel sources with rear center speaker. In this case the

program name changes to the corresponding name for 6.1 channel.

• When playing 6.1 channel source with 6.1/ES on the remote control off, the program name changes to the corresponding name for

5.1 channel.

Note

• The “ ” indicator does not light up when selecting the program No. 11 except for the Enhanced mode.

No.

0106V2200_31-35_EN(U) 01.8.1, 9:44 AM34

English

INTRODUCTION PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CINEMA-DSP

Program

Enhanced Mode

No.

Program

ENTERTAINMENT/

Game

TV SPORTS

MONO MOVIE

Features

This program adds a deep and spatial feeling to video game sounds.

With this program, you can enjoy watching various TV programs such as news, variety shows,

music programs or sports programs. In a stereo broadcast of a sports game, the commentator is

oriented at the center position, and the shouts and the atmosphere in the stadium spread on the

surround side, while their spread to the rear is properly restrained.

This program is provided for reproducing monaural video sources (such as old movies). The

program produces the optimum reverberation to create sound depth by using only the presence

sound field.

■ For audio-video sources in 2-channel: No. 6 to 8

The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in

mind that most of these are precise digital recreations of actual acoustic environments.

Note

• Select the DSP program that you feel sounds best regardless of the name and description given for it below.

No.

Features

This program creates the extremely wide sound field of a 70-mm movie theater. It

precisely reproduces the source sound in detail, making both the video and the sound

field incredibly real. This is ideal for any kind of video source encoded with Dolby

Surround, Dolby Digital or DTS (especially large-scale movie productions).

This program clearly reproduces dialog and sound effects in the latest sound form of

science fiction films, thus creating a broad and expansive cinematic space amid the

silence. You can enjoy science fiction films in a virtual-space sound field that includes

Dolby Surround, Dolby Digital and DTS-encoded software employing the most advanced

techniques.

This program is ideal for precisely reproducing the sound design of the newest 70-mm

and multichannel soundtrack films. The sound field is made to be similar to that of the

newest movie theaters, so the reverberations of the sound field itself are restrained as

much as possible.

This program is for reproducing sounds from 70-mm and multichannel soundtrack films,

and is characterized by a soft and extensive sound field. The presence sound field is

relatively narrow. It spatially spreads all around and toward the screen, restraining the

echo effect of conversations without losing clarity.

This program ideally simulates the multi-surround speaker systems of the 35-mm film

theaters. Dolby Pro Logic decoding, Dolby Digital decoding or DTS decoding and digital

sound field processing create precise effects without altering the original sound

orientation.

The surround effects produced by this sound field wrap around the viewer naturally from

the back to the left and right, and toward the screen.

MOVIE

THEATER 1

MOVIE

THEATER 2

Spectacle

Sci-Fi

Adventure

General

0106V2200_31-35_EN(U) 01.8.1, 9:44 AM35

■ Connecting the AM loop antenna

1 Set up the AM loop antenna, then connect it.

2 Press and hold the tab to insert the AM loop

antenna lead wires into the AM ANT and

GND terminals.

3 Orient the AM loop antenna for the beat

reception.

• The AM loop antenna can be removed from the stand and

attached to a wall, etc.

Notes

• The AM loop antenna should be placed away from this unit.

• The AM loop antenna should always be connected, even if an

outdoor AM antenna is connected to this unit.

A properly installed outdoor antenna provides clearer

reception than an indoor one. If you experience poor

reception quality, an outdoor antenna may improve the

quality. Consult the nearest authorized YAMAHA

dealer or service center about the outdoor antennas.

TUNING

Connecting the Antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal

strength.

Connect each antenna correctly to the designated terminals.

■ Connecting the indoor FM

antenna

Connect the included indoor FM antenna to the 75Ω

UNBAL. FM ANT terminal.

CONTROL O

COMPONENT VIDEO

PR/ CR

DVD

ONITOR

OUT

D-TV / LD

PB/ CB Y

75Ω UNBAL.

ANT

GND

ANT

TUNER

FREQUENCY STEP switch (China and General

models only)

Because the interstation frequency spacing

differs in different areas, set the

FREQUENCY STEP switch (locating on

the rear panel) according to the frequency

spacing in your area.

North, Central and South America:

100 kHz/10 kHz

Other area: 50 kHz/9 kHz

Before setting this switch, disconnect the

AC power plug of this unit from the AC

outlet.

100kHz/10kHz

FREQUENCY

STEP

50kHz/9kHz

FM AM

(U.S.A. model)

Ground (GND terminal)

For maximum safety and minimum

interference, connect the antenna GND

terminal to a good earth ground. A good

earth ground is a metal stake driven into

moist earth.

Indoor FM

antenna

(included)

AM loop antenna

(included)

0107V2200_36-41_EN(U) 01.8.1, 9:44 AM36

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

TUNING

4 Press PRESET/TUNING l / h once to begin

automatic tuning.

Press h to tune in to a higher frequency, or press l

to tune in to a lower frequency. Press the same button

again if the tuning search does not stop at the desired

station.

When tuned in to a station, the “TUNED” indicator

lights up and the frequency of the received station is

shown on the front panel display.

• Use the manual tuning method if the tuning search does not

stop at the desired station because the signal is weak.

■ Manual tuning

If the signal from the station you want to select is weak,

you must tune in to it manually.

1 Select TUNER and the reception band

following steps 1 and 2 described in

“Automatic tuning” on left.

2 Press TUNING MODE (AUTO/MAN’L MONO)

so that the “AUTO” indicator goes off from

the front panel display.

If the colon (:) appears on the front panel display

next to the band indication, press PRESET/TUNING

EDIT to turn it off.

3 Press PRESET/TUNING l / h to tune in to

the desired station manually.

Hold down the button to

continue the tuning search.

Note

• Manually tuning in to an FM station will automatically change

the reception mode to monaural to increase the signal quality.

Automatic and Manual Tuning

There are 2 ways of tuning; automatic and manual.

Automatic tuning is effective when station signals are

strong and there is no interference.

■ Automatic tuning

1 Press INPUT l / h (TUNER on the remote

control) to select TUNER as the input source.

2 Press FM/AM to select the reception band.

“FM” or “AM” appears on the front panel display.

3 Press TUNING MODE (AUTO/MAN’L MONO)

so that the “AUTO” indicator lights up on the

front panel display.

If the colon (:) appears on the front panel display

next to the band indication, press PRESET/TUNING

EDIT to turn it off.

INPUT

PRESET/

TUNING

BASS

VOLUMEINPUT

INPUT M0DE

VIDEO AUXSILENT

PROGRAM

STEREO

SPEAKERS

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

NATURAL SOUND AV RECEIVER

6CH INPUT

– +

TREBLE

– +

PRO LOGIC

REC OUT/ZONE 2

V-AUX

VCR2

/DVR

VCR1

PHONO

TUNER

MD/TAPE

DVD

SOURCE

/REMOTE

D-TV/LD

CBL/SAT

CD-R

DIGITAL

STANDBY

FM/AM

TUNING

MODE

AUTO/MAN'L MONO

AUTO

Lights up

PRESET

/TUNING

EDIT

PHONO

DVD

VCR2/DVR

VCR 1

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

Front panel Remote control

TUNING

MODE

AUTO/MAN'L MONO

AUTO

Goes off

PRESET

/TUNING

EDIT

PRESET/

TUNING

CR DVD TUNER CDCD R1

CBL

SAT

TAPE

TUNED

A AM 1404

CR DVD TUNER CDCD R1

CBL

SAT

TAPE

TUNED

A AM 1404

CR DVD TUNER CDCD R1

CBL

SAT

TAPE

TUNED

A AM 1404

0107V2200_36-41_EN(U) 01.8.1, 9:44 AM37

TUNING

Presetting Stations

■ Automatically presetting stations

(for FM stations)

You can use the automatic preset tuning feature to store

FM stations. This function enables this unit to

automatically tune in to FM stations with strong signals,

and to store up to 40 (8 stations x 5 groups) of those

stations in order. This feature enables you to easily tune in

to any preset station by selecting the preset station

number (see page 40).

1 Press FM/AM to select the FM band.

2 Press TUNING MODE (AUTO/MAN’L MONO)

so that the “AUTO” indicator lights up on the

front panel display.

3 Press and hold MEMORY (MAN’L/AUTO FM)

for more than 3 seconds.

The preset number, the “MEMORY” and “AUTO”

indicators flash. Then, after about 5 seconds,

automatic preset tuning begins from the frequency

currently displayed toward the higher frequencies.

When automatic preset tuning is completed, the front

panel display shows the frequency of the last preset

station.

TUNING

MODE

AUTO/MAN'L MONO

MEMORY

MAN'L/AUTO FM

AUTO

VCR DVD TUNER CD

PHONO

CD RV AUX 1

VCR2/DVR

CBL

SAT

TAPE

MEMORY

MUTE VOLUME

SLEEP

AUTO

A1:FM

BASS

VOLUMEINPUT

INPUT M0DE

VIDEO AUXSILENT

PROGRAM

STEREO

SPEAKERS

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

NATURAL SOUND AV RECEIVER

6CH INPUT

– +

TREBLE

– +

PRO LOGIC

REC OUT/ZONE 2

V-AUX

VCR2

/DVR

VCR1

PHONO

TUNER

MD/TAPE

DVD

SOURCE

/REMOTE

D-TV/LD

CBL/SAT

CD-R

DIGITAL

STANDBY

Lights up

Notes

• Any stored station data existing under a preset number is

cleared when you store a new station under that preset number.

• When a station data is stored under a preset number, the

frequency and reception band are also stored.

• You can manually replace a preset station with another FM or

AM station by simply following the procedure in the section

“Manually presetting stations” on page 39.

• If the number of the received stations does not reach E8,

automatic preset tuning has automatically stopped after

searching all stations.

• Only FM stations with sufficient signal strength are stored

automatically by automatic preset tuning. If the station you

want to store is weak in signal strength, tune in to it manually

in the monaural mode, and store it by following the procedure

in “Manually presetting stations” on page 39.

Automatic preset tuning options

You can select the preset number from which this unit

will store FM stations and/or begin tuning toward lower

frequencies. After pressing MEMORY in step 3:

1. Press A/B/C/D/E and PRESET/TUNING l / h (A/B/

C/D/E and PRESET –/+ on the remote control) to

select the preset number under which the first station

will be stored. Automatic preset tuning will stop when

stations have all been stored up to E8.

2. Press PRESET/TUNING EDIT to turn off the colon (:)

and then press PRESET/TUNING l to begin tuning

toward lower frequencies.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost even if this unit is set in the standby

mode, the power cord is disconnected from the AC

outlet, or the power supply is temporarily cut due to

power failure. However, if the power is cut for more

than one week, the preset stations may be cleared. If

so, store the stations again by using the presetting

station methods.

FM/AM

0107V2200_36-41_EN(U) 01.8.1, 9:44 AM38

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

TUNING

■ Manually presetting stations

You can also store up to 40 stations (8 stations x 5

groups) manually.

*1 These buttons can be used to directly select the preset group

(A to E from left to right). – same for page 40

*2 These buttons can be used to directly select the preset station

number 1 to 8. – same for page 40

1 Tune in to a station.

See page 37 for tuning instructions.

When tuned in to a station, the front panel display

shows the frequency of received station.

2 Press MEMORY (MAN’L/AUTO FM).

The “MEMORY” indicator flashes for about

5 seconds.

3 Press A/B/C/D/E (A/B/C/D/E on the remote

control) repeatedly to select a preset station

group (A to E) while the “MEMORY” indicator

is flashing.

The group letter appears and make sure that the

colon (:) appears on the front panel display next to

the band indication.

BASS

VOLUMEINPUT

INPUT M0DE

VIDEO AUXSILENT

PROGRAM

STEREO

SPEAKERS

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

NATURAL SOUND AV RECEIVER

6CH INPUT

– +

TREBLE

– +

PRO LOGIC

REC OUT/ZONE 2

V-AUX

VCR2

/DVR

VCR1

PHONO

TUNER

MD/TAPE

DVD

SOURCE

/REMOTE

D-TV/LD

CBL/SAT

CD-R

DIGITAL

STANDBY

43 2,5

Shows the displayed station has been stored as C3.

4 Press PRESET/TUNING l / h (PRESET –/+

on the remote control) to select a preset

station number (1 to 8) while the “MEMORY”

indicator is flashing.

Press h to select a higher preset station number.

Press l to select a lower preset station number.

5 Press MEMORY (MAN’L/AUTO FM) on the

front panel while the “MEMORY” indicator is

flashing.

The station band and frequency

appear on the front panel

display with the preset group

and number you have selected.

6 Repeat steps 1 to 5 to store other stations.

Notes

• Any stored station data existing under a preset number is

cleared when you store a new station under that preset number.

• The reception mode (stereo or monaural) is stored along with

the station frequency.

MEMORY

MAN'L/AUTO FM

MEMORY

A/B/C/D/E

VCR DVD TUNER CD

PHONO

CD RV AUX 1

VCR2/DVR

CBL

SAT

TAPE

MEMORY

MUTE VOLUME

SLEEP

C :AM 576 kHz

Flashes

VCR DVD TUNER CD

PHONO

CD RV AUX 1

VCR2/DVR

CBL

SAT

TAPE

MUTE VOLUME

SLEEP

A AM 576 kHz

Remote controlFront panel

TV INPUT

A/B/C/D/E

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

PLAY

– +

100

11 12

234

PRESET/

TUNING

Front panel

VCR DVD TUNER CD

PHONO

CD RV AUX 1

VCR2/DVR

CBL

SAT

TAPE

TUNED

VOLUME

C3:AM 576 kHz

MEMORY

MAN'L/AUTO FM

VCR DVD TUNER CD

PHONO

CD RV AUX 1

VCR2/DVR

CBL

SAT

TAPE

TUNED

VOLUME

C3:AM 576 kHz

Remote control

PRESET

DISC

0107V2200_36-41_EN(U) 01.8.1, 9:44 AM39

TUNING

Exchanging Preset Stations

You can exchange the assignment of two preset stations

with each other. The example below describes the

procedure for exchanging preset station “E1” with “A5”.

1 Tune in to preset station “E1” by using the

A/B/C/D/E and PRESET/TUNING. (A/B/C/D/E

and PRESET –/+ on the remote control)

See “Tuning in to a Preset Station” on left.

2 Press and hold PRESET/TUNING EDIT for

more than 3 seconds.

“E1” and the “MEMORY” indicator flash on the

front panel display.

3 Tune in to preset station “A5” by using the

A/B/C/D/E and PRESET/TUNING. (A/B/C/D/E

and PRESET –/+ on the remote control)

“A5” and the “MEMORY” indicator flash on the

front panel display.

4 Press PRESET/TUNING EDIT again.

The stations stored at the two preset assignments are

exchanged.

Tuning in to a Preset Station

You can tune any desired station simply by selecting the

preset station number under which it was stored.

1 Press A/B/C/D/E (A/B/C/D/E on the remote

control) to select the preset station group.

The preset group letter appears on the front panel

display and changes each time you press A/B/C/D/E.

2 Press PRESET/TUNING l / h (PRESET –/+

on the remote control) to select a preset

station number (1 to 8).

The preset group and number appear on the front

panel display along with the station band, frequency

and the “TUNED” indicator lights up.

PRESET

/TUNING

EDIT

PRESET

DISC

PRESET/

TUNING

A/B/C/D/E

TV INPUT

A/B/C/D/E

VCR DVD TUNER CD

PHONO

CD RV AUX 1

VCR2/DVR

CBL

SAT

TAPE

TUNED

MEMORY

MUTE VOLUME

SLEEP

A5:FM 90.6 MHz

VCR DVD TUNER CDCD RV AUX 1

VCR2/DVR

CBL

SAT

TAPE

MEMORY

EDIT E1-A5

Shows the exchange of stations has

been completed.

Front panel

Remote control

Front panel

Remote control

BASS

VOLUMEINPUT

INPUT M0DE

VIDEO AUXSILENT

PROGRAM

STEREO

SPEAKERS

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

NATURAL SOUND AV RECEIVER

6CH INPUT

– +

TREBLE

– +

PRO LOGIC

REC OUT/ZONE 2

V-AUX

VCR2

/DVR

VCR1

PHONO

TUNER

MD/TAPE

DVD

SOURCE

/REMOTE

D-TV/LD

CBL/SAT

CD-R

DIGITAL

STANDBY

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

100

11 12

234

BASS

VOLUMEINPUT

INPUT M0DE

VIDEO AUXSILENT

PROGRAM

STEREO

SPEAKERS

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

NATURAL SOUND AV RECEIVER

6CH INPUT

– +

TREBLE

– +

PRO LOGIC

REC OUT/ZONE 2

V-AUX

VCR2

/DVR

VCR1

PHONO

TUNER

MD/TAPE

DVD

SOURCE

/REMOTE

D-TV/LD

CBL/SAT

CD-R

DIGITAL

STANDBY

2,41,31,3

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

100

11 12

234

1, 3

PRESET

/TUNING

EDIT

VCR DVD TUNER CD

PHONO

CD R1

CBL

SAT

TAPE

TUNED

MEMORY

MUTE

SLEEP

E1:FM 87.50 MHz

VCR DVD TUNER CD

PHONO

CD R1

CBL

SAT

TAPE

TUNED

MEMORY

MUTE

SLEEP

E1:FM 87.50 MHz

0107V2200_36-41_EN(U) 01.8.1, 9:44 AM40

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

BASIC RECORDING

REC OUT/ZONE 2 allows you to record one source

while watching and/or listening to another source.

Recording adjustments and other operations are

performed from the recording components. Refer to the

operation instructions for these components.

1 Turn on the power to this unit and all

connected components.

2 Select the source component you want to

record from by using REC OUT/ZONE 2.

• To record the current input source, set REC OUT/

ZONE 2 to SOURCE/REMOTE.

• If you want to watch or listen to another source,

set REC OUT/ZONE 2 to the source you want to

record.

Note

• At this setting, you can change the source to listen to or watch

during recording by pressing INPUT l/h (one of the input

selector buttons on the remote control).

3 Start playback (or select a broadcast station)

on the source component.

4 Start recording on the recording component.

• Setting REC OUT/ZONE 2 to SOURCE/REMOTE and using

the BGV function (see page 26) allows the recording of audio

and video from a different source.

Notes

• Do a test recording before you start an actual recording.

• When this unit is set in the standby mode, you cannot record

between other components connected to this unit.

• The setting of BASS, TREBLE, BASS EXTENSION,

VOLUME, “3 L/R BALANCE” on the SET MENU and DSP

programs does not affect the recorded material.

• A source connected to the 6CH INPUT jacks of this unit

cannot be recorded.

• S-video and composite video signals pass independently

through this unit’s video circuits. Therefore, when recording or

dubbing video signals, if your video source component is

connected to provide only an S-video (or only a composite

video) signal, you can record only an S-video (or only a

composite video) signal by your VCR.

• A given input source is not output on the same REC OUT

channel. (For example, the signal input from VCR 1 IN is not

output on VCR 1 OUT.)

• Check the copyright laws in your country to record from

records, CDs, radio, etc. Recording of copyrighted material

may infringe copyright laws.

If you playback a video source that uses scrambled or

encoded signals to prevent it from being dubbed, the

picture itself may be disturbed due to those signals.

■ Special considerations when

recording DTS software

The DTS signal is a digital bitstream. Attempting to

digitally record the DTS bitstream will result in noise

being recorded. Therefore, if you want to use this unit to

record sources that have DTS signals recorded on them,

the following considerations and adjustments need to be

made.

For LDs, DVDs and CDs encoded with DTS, when your

player is compatible with the DTS format, follow its

operation instruction to make a setting so that the analog

signal will be output from the player.

■ Timer playback/recording

This unit can perform playback or recording with an

external timer (not supplied). Refer to the operation

instruction for the component and the timer to be used.

Notes

• The stored data such as input source will be reflected in the

playback or recording with the timer.

• If you do not want any sound output during the recording with

a timer, turn the volume down.

Memory back-up

The memory back-up circuit prevents the stored data

(input source, volume level, set menu settings and so

on) from being lost even if this unit is in the standby

mode (disconnected from the AC outlet). However if

the timer is turned off for more than one week, the

stored data will be lost.

BASS

VOLUMEINPUT

INPUT M0DE

VIDEO AUXSILENT

PROGRAM

STEREO

SPEAKERS

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

NATURAL SOUND AV RECEIVER

6CH INPUT

– +

TREBLE

– +

PRO LOGIC

REC OUT/ZONE 2

V-AUX

VCR2

/DVR

VCR1

PHONO

TUNER

MD/TAPE

DVD

SOURCE

/REMOTE

D-TV/LD

CBL/SAT

CD-R

DIGITAL

STANDBY

VCR2

/DVR

V-AUX

VCR 1

CBL/SAT

D-TV/LD

DVD

SOURCE

/REMOTE

REC OUT/ZONE 2

MD/TAPE

CD-R

TUNER

PHONO

VCR2

/DVR

V-AUX

VCR 1

CBL/SAT

D-TV/LD

DVD

SOURCE

/REMOTE

REC OUT/ZONE 2

MD/TAPE

CD-R

TUNER

PHONO

0107V2200_36-41_EN(U) 01.8.1, 9:44 AM41

REMOTE CONTROL FEATURES

The remote control can operate other A/V components of YAMAHA and other manufacturers as well as this unit. To

control those components, you must set up remote control with the manufacturer codes.

This remote control also has two sophisticated features: Learn and Macro. The Learn feature allows it to acquire

functions from the remote controls of other components in your system (or other household appliances) equipped with

an infrared remote control receiver. The Macro feature allows you to program a series of operations in sequence for

operation by a single button, or to use the factory-set macros to operate other YAMAHA components. These features

make it possible for you to reduce the number of remote control in your entertainment room.

Notes

• For the operating distance of the remote control and notes about batteries, see pages 3 and 7.

• For the name and function of each part and button, see pages 6 and 7.

Control Area

■ Control area of this unit

The control area of this unit is the shaded area shown

below. You can use the functions within this area no

matter which component control area is selected.

■ Control area for each component

The component control area is the shaded area shown

below. Each component has different functions for the

operation buttons in the component control area. The

component which has been chosen by pressing an input

selector button or SOURCE SELECT k/n can be

controlled and the display window shows the

corresponding name of the component to be operated.

Å/ı buttons and input

selector buttons switch the

control area for each

component.

* Å/ı buttons is to operate

the other components that are

not connected to this unit.

Factory setting:

Å ........... LD player

ı ..... Satellite tuner

Component control area

There are 13 component control areas. You can set up the

manufacturer code and program other remote control functions in

each area. See pages 50 to 54.

Input selector

buttons, and Å/ı

buttons

TRANSMIT

RE-NAME

STANDBY

6CH INPUT

SOUND

SYSTEM

CLEAR LEARN MACRO

OFF ON

MACRO

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAU S ESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

PARAMETER

SET MENU

EFFECT

LEVEL

ON SCREEN

TESTSLEEP

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SOURCE

PLAY

–+

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

POWER

100

11 12

234

TRANSMIT

RE-NAME

STANDBY

6CH INPUT

SOUND

SYSTEM

CLEAR LEARN MACRO

OFF ON

MACRO

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

POWER

100

11 12

234

SOUND

TITLE

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

TV INPUT

TV VOL

PRESET

DISC

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

DISPLAY

PLAY

– +

ENTER

100

11 12

234

DSP is selected

10 key is selected

0108V2200_42-54_EN(U) 01.8.1, 2:40 PM42

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

REMOTE CONTROL FEATURES

1 Press an input selector button, Å or ı to

select the source component you want to set

up.

2 Press and hold LEARN for about 3 seconds

by using a ballpoint pen or similar object.

“SETUP” and the selected component name appear

alternately in the display window.

Notes

• Press LEARN for at least 3 seconds, otherwise the learning

process is started.

• If you do not press any button within 30 seconds during step 3,

the setup process is canceled. If this happens, start over from

step 2.

3 Press k / n to select the name of your

component’s manufacturer.

You will find the names of most worldwide audio-

video manufacturers in alphabetical order in the

display window.

If you want to change a library (component

category), press l / h. You can set a

different component from the input selector

name.

Library choices: DVD, LD, CD, CD-R, MD, TAPE,

TUNER, AMP, TV, CABLE, DBS, SAT, VCR

Note

If the manufacturer of your component has more than one codes,

try each of them until you find the correct one as checking if it

works following step 4.

4 Press one of the buttons shaded below to

check if it works for the component being

set. If it does, the manufacturer code setting

has been correctly made.

• If you continuously want to set up another code for another

component, press ENTER and repeat steps 1, 3 and 4.

5 Press LEARN again to exit from the setup

mode.

Notes

• If you have already programmed a remote control function for

a button, the function by learning or macro programming takes

priority over the setup manufacturer code’s function.

• “ERROR” appears in the display window under the following

circumstances:

– when pressing a button other than the cursor and ENTER;

– when pressing more than one button at once; or

– when MACRO ON/OFF, 10KEY/DSP or PARAMETER/SET

MENU is switched to another position.

Setting the Manufacturer Code

You can control other components by setting a

manufacturer code. A code can be set up in each

component control area.

The following table shows factory-set component

(Library: component category) and the manufacturer code

for each area. If you are to make a setting for different

component from the factory setting, change the library as

described in step 3 on right.

LEARN

Input area

PHONO

TUNER

V-AUX

CBL/SAT

MD/TAPE

CD-R

D-TV/LD

VCR 1

VCR 2/DVR

DVD

Component category

(Library)

SATELLITE TUNER

TUNER

VCR

CABLE

CD-R

VCR

DVD

Manufacturer

YAMAHA

–

YAMAHA

–

YAMAHA

–

YAMAHA

ENTER

6CH INPUT

SOUND

TITLE

CHAPTER

PAUSESTOPPOWER

REC

SELECT

DISPLAY

SOURCE

PLAY

–+

ENTER

PHONO

DVD

VCR2/DVR

VCR 1

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

0108V2200_42-54_EN(U) 01.8.3, 7:41 PM43

REMOTE CONTROL FEATURES

5 Press the button for which you want to

program the new function.

“LEARN” is displayed.

6 Press and hold the button on the other

remote control that has the function you

want to program into this remote control

until “OK” appears in the display window.

Notes

• “NG” appears in the display window when programming has

not been done correctly. In this case, start over from step 5.

• This remote control can learn approximately 120 functions.

However depending on the signals learned, “FULL” may

appear in the display window much earlier than this number. In

this case, clear unnecessary programmed functions to make

further learning on the remote control.

7 Repeat steps 5 and 6 to program additional

functions.

8 Press LEARN again to exit from the learning

mode.

Notes

• It is also possible to program in the control area of this unit

with 10KEY/DSP set to DSP. However, if you program

functions in this area, you cannot control this unit and select a

DSP program.

• Even if the batteries in the other remote control have enough

power to transmit signals for operation, they may not have

enough power to transmit signals to this remote control.

• When the remote controls are either too close together or too

far apart, you may not be able to program this remote control.

• Direct sunlight interferes with infrared rays.

• “ERROR” appears in the display window in the following

circumstances:

– when pressing more than one button at once; or

– when MACRO ON/OFF is switched to another position.

Programming a New Remote

Control Function (Learn Feature)

If you want to program functions not included in the basic

operations covered by the manufacturer code, or a

manufacturer code is not available, the following

procedure needs to be performed. The possible

programming area is the same as a component control

area, so the buttons are programmable independently for

each source component area.

Note

• This remote control transmits infrared rays. If the other remote

control also uses infrared rays, this remote control can learn

most of the other remote control’s functions. However, you

may not be able to program some special signals or extremely

long transmissions. (Refer to the operation instructions for the

other remote control.)

1 Set 10KEY/DSP to 10KEY.

2 Press an input selector button, Å or ı to

select a source component.

3 Place this remote control and the other

remote control about 5 to 10 cm apart on a

flat surface so that their infrared transmitters

are aimed at each other.

4 Press LEARN by using a ballpoint pen or

similar object.

Do not press and hold LEARN longer than three

seconds. Otherwise this unit enters the manufacturer

code setting mode.

Note

• If you do not press any button within 30 seconds during steps 5

and 6, the learning process is canceled. If this happens, start

over from step 4.

TRANSMIT

RE-NAME

STANDBY

6CH INPUT

SYSTEM

CLEAR LEARN MACRO

OFF ON

MACRO

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

SOURCE

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AU X

POWER

5 to 10 cm (2 to 4 inch)

TRANSMIT

RE-NAME

STANDBY

6CH INPUT

SYSTEM

CLEAR LEARN MACRO

OFF ON

MACRO

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

SOURCE

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AU X

POWER

LEARN

TRANSMIT

RE-NAME

STANDBY

6CH INPUT

SYSTEM

CLEAR LEARN MACRO

OFF ON

MACRO

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

SOURCE

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AU X

POWER

DSP

10KEY

Flashes alternately

PHONO

DVD

VCR2/DVR

VCR 1

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

0108V2200_42-54_EN(U) 01.8.6, 2:58 PM44

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

REMOTE CONTROL FEATURES

Using the Macro Feature

The Macro feature makes it possible to perform a series of operations by pressing just one button. For example, when

you want to play a CD, normally you would turn on the components, select the CD input, and press the play button to

start playback. The Macro feature lets you perform all those operations by simply pressing the CD macro button. The

macro buttons (the input selector buttons, Å and ı buttons, SYSTEM POWER and STANDBY) are factory set with

macro programs. You can also program your own macros (see page 46).

*1 In order to turn on some components (including YAMAHA components) connected to this unit, connect those

components to the AC OUTLET(S) on the rear panel. (Power control may not be synchronized with this unit

depending on the component. For details, please refer to the operation instruction for the connected component.)

*2 If the macro you select includes power control functions, the component may be turned off if it is already on when

you press the macro button. For example, if your TV is on and you press the SYSTEM POWER macro button, the

TV is turned off.

*3 Playback can be started with any YAMAHA remote control-compatible MD recorders, CD players, CD recorders,

DVD players, and LD players. When using macros to operate other components, it is either necessary to program the

PLAY button on the control area of that component (see page 44) or to set up a manufacturer code (see page 43).

*4 When TUNER is selected as the input source, this unit receives the last station when this unit is set in the standby

mode.

(DVD area) (*3)

Press one of the macro buttons

Automatically transmits signals of each button sequentially

SYSTEM

POWER

PLAY

(CD area)

Macro buttons

PHONO

V-AUX

TUNER

MD/TAPE

CD-R

D-TV/LD

CBL/SAT

VCR 1

VCR2/DVR

DVD

STANDBY

SYSTEM

POWER

First Second

–

Third

–

PHONO

V-AUX

TUNER

MD/TAPE

CD-R

D-TV/LD

CBL/SAT

VCR 1

VCR2/DVR

DVD

SYSTEM

POWER

STANDBY

POWER

PLAY

(*1)

(D-TV/LD area) (*2)

PLAY

(MD/TAPE area) (*3)

(CD-R area) (*3)

(CD area) (*3)

(VCR 1 area) (*3)

(VCR 2/DVR area) (*3)

(*4)

0108V2200_42-54_EN(U) 01.8.1, 2:47 PM45

REMOTE CONTROL FEATURES

2 Press a macro button for which you want to

program the macro operation.

The button you chose for programming the macro

operation and the selected component name appear

alternately in the display window.

Note

• “AGAIN” appears in the display window when a button other

than the macro buttons is pressed.

• If you want to change the source component, use SOURCE

SELECT k / n or input selector buttons. When you use the

input selector buttons, selecting the input is programmed as a

macro step, whereas SOURCE SELECT k / n only changes

the component.

3 Press the buttons of the functions that you

want to include in the macro operation

sequence in order.

• You can set up to 10 steps (10 functions). After you have set 10

steps, “FULL” appears and the remote control automatically

exits from the macro mode.

Note

• “NG” appears in the display window when programming has

not been done correctly. In this case, start over from step 2.

■ Operating the macro

1 Set MACRO ON/OFF to ON.

2 Press a macro button.

Notes

• When you have finished using the Macro feature, set MACRO

ON/OFF to OFF.

• While this unit is carrying out a macro program, this unit does

not receive any other button’s function until the macro

operation has been completed (the TRANSMIT indicator stops

flashing).

• Continue to aim the remote control at the component the macro

is operating until the macro operation has been completed.

■ Programming a macro

You can program your own macros and use the Macro

feature to transmit many remote control commands by

pressing a single button.

Notes

• The factory-set macro is not cleared when a new macro is

programmed for a button. The factory-set macro can be used

again when the programmed macro is cleared.

• It is not possible to add a new signal (macro step) to the

factory-set macro. Programming a macro changes all macro

contents.

• A macro programming is used to transmit learning or setup (or

YAMAHA preset) button signals of this remote control to a

macro button. If necessary, set up the manufacturer code or

program a function with the remote control for your

component.

• This remote control handles button signals that operate

continuously, such as volume control, as short time interval

codes. Macro programming that include these types of macro

steps are therefore not recommended.

1 Press MACRO by using a ballpoint pen or

similar object.

“MCR ?” appears in the display window.

Note

• If you do not press any button within 30 seconds during steps 2

and 3, the macro programming process is canceled. If this

happens, start over from step 1.

TRANSMIT

RE-NAME

STANDBY

SYSTEM

CLEAR LEARN MACRO

OFF ON

MACRO

PHONO

DVD

VCR2/DVR

VCR 1

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

POWER

Macro buttons

MACRO

MACRO ON/OFF

MACRO

indicate the number

of macro steps you

entered

STANDBY

6CH INPUT

SOUND

SYSTEM

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAUSESTOPPOWER

REC

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

POWER

MCR 2 : DVD p

MCR 1 : DVD a

appear alternately so that you can

set up the next step

PHONO

DVD

VCR2/DVR

VCR 1

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

0108V2200_42-54_EN(U) 01.8.1, 2:51 PM46

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

REMOTE CONTROL FEATURES

RE-NAME

4 Press MACRO again when

the operation sequence

you want to program is

complete.

Note

• “ERROR” appears in the display window under the following

circumstances:

– when pressing more than one button at once; or

– when MACRO ON/OFF is switched to another position.

Memory back-up

If the remote control is without batteries for more than

3 minutes, or if exhausted batteries remain in the

remote control, the contents of the memory may be

cleared. When the memory is cleared, insert new

batteries, set up the manufacturer code and program

any acquired functions that may have been cleared.

Changing the Source Name in the

Display Window

You can change the name that appears in the display

window on the remote control if you want to use the

different name from the original input selector button

names. This is useful when different component is set in

the input selector button.

1 Press an input selector button, Å or ı to

select the source component you want to

rename.

The selected component name appears in the display

window.

2 Press RE-NAME by using

a ballpoint pen or similar

object.

3 Press k / n to select and enter a character.

Pressing n changes the character in the following

order: A to Z, a to z, 0 to 9, space, - (hyphen) and /

(slash). (Pressing k goes in the reverse order.)

4 Press l / h to move the cursor to the next

position.

RE-NAME

ENTER

• If you continuously want to rename another source component,

press ENTER and repeat steps 1, 3 and 4.

5 Press RE-NAME again to exit from the

renaming mode.

MACRO

Clearing Learned Functions,

Macros, Renamed Source Names,

and Setup Manufacturer Codes

1 Press an input selector button, Å or ı to

select the source component you want to

clear the function, Macros, names or

manufacturer codes.

The selected component name appears in the display

window.

2 Press CLEAR by using a ballpoint pen or

similar object.

Note

• If you do not press any button within 30 seconds during steps 2

and 3, the clearing process is canceled. If this happen, start

over from step 1.

CLEAR

PHONO

DVD

VCR2/DVR

VCR 1

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

PHONO

DVD

VCR2/DVR

VCR 1

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

0108V2200_42-54_EN(U) 01.8.1, 2:52 PM47

REMOTE CONTROL FEATURES

3 Press k / n to select the clear mode.

The mode is shown in the display window in the

following order:

4 Press and hold CLEAR again for about 3

seconds.

“C:OK” appears in the display window.

Note

•“C:NG” appears in the display window if the operation is

unsuccessful. In this case, start over from step 2.

5 Press CLEAR to exit from the clearing mode.

Once you have cleared a learned function or macro

for a button, the button reverts to the factory setting.

Note

•“ERROR” appears in the display window under the following

circumstances:

– when pressing a button other than the cursor and ENTER;

– when pressing more than one button at once; or

– when MACRO ON/OFF, 10KEY/DSP or PARAMETER/SET

MENU is switched to another position.

CLEAR

Clearing a Learned Function or

Macro

You can clear the function learned in a certain

programmable button in each area.

■ To clear a learned function

1 Press an input selector button, Å or ı to

select the source component you want to

clear the function.

The selected component name appears in the display

window.

2 Press LEARN by using a ballpoint pen or

similar object.

“LEARN” and the selected component name appear

alternately in the display window.

Note

• If you do not press any button within 30 seconds during step 3,

the clearing process is canceled. If this happens, start over from

step 2.

3 Press the button that you want to clear for 3

seconds as pressing CLEAR by using a

ballpoint pen or similar object.

“C:OK” appears in the display window.

4 Press LEARN again to exit

from the learning mode.

■ To clear the macro function

1 Press an input selector button, Å or ı to

select the source component for which you

want to clear the function.

The selected component name appears in the display

window.

LEARN

CLEAR

Clears all programmed functions

including setup manufacturer

codes. This returns to the

factory settings.

(L: name of a component) Clears

all learned functions for the

component area. Press the input

selector button, Å or ı to select

the component.

Clears all learned functions for

this unit control area.

Clears all learned functions.

Clears all programmed macros.

Clears all renamed source

names in the display window.

LEARN

PHONO

DVD

VCR2/DVR

VCR 1

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

PHONO

DVD

VCR2/DVR

VCR 1

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

0108V2200_42-54_EN(U) 01.8.1, 9:44 AM48

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

REMOTE CONTROL FEATURES

Pressing n always selects OPTN first

SELECT

SOURCE

Pressing k selects “Zone2” first

6CH INPUT

SOUND

TITLE

CHAPTER

PAU S ESTOPPOWER

REC

SELECT

DISPLAY

SOURCE

PLAY

–+

ENTER

6CH INPUT

SOUND

TITLE

CHAPTER

PAUSESTOPPOWER

REC

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

■ SOURCE SELECT k / n

You can control another component independently from

the input you have selected by pressing an input selector

button.

Press SOURCE SELECT k / n to choose the

component and set the remote control to be

used for it.

The display window will show one of the following:

(when pressing n) OPTN (option), Å, ı, PHONO,

V-AUX, TUNER, MD, CD-R, CD, TV/LD (TV or

digital TV/LD), CBSAT (cable TV/satellite tuner),

VCR 1, VCR 2, DVD.

• Pressing k shows the same in the reverse order, but you cannot

select OPTN.

■ OPTN (option) area

OPTN is an extra component control area that can be

programmed with other remote control functions.

Note

• You cannot set up the manufacturer code in this area. See

page 44 for the programming procedure.

■ Zone 2 feature

When you make up a second audio-video room with this

unit’s Zone 2 feature, you must set “Zone2” as the

amplifier library in the remote control first. Selecting

“Zone2” by pressing k sets the remote control to the

Zone 2 mode. See pages 68 and 69 for details.

2 Press MACRO to clear a programmed macro

by using a ballpoint pen or similar object.

3 Press and hold CLEAR by using a ballpoint

pen or similar object, and at the same time

press the button for which you want to clear

the macro for about 3 seconds.

“C:OK” appears in the display window.

• You can clear other learned functions and macros at this time

by holding down CLEAR again and pressing the other buttons

for which those learned functions or macros have been

programmed.

Note

• “C:NG” appears in the display window if the operation is

unsuccessful. In this case, try step 3 again.

4 Press MACRO again to exit from the clearing

mode.

Once you have cleared a learned function or macro

for a button, the button reverts to the factory setting.

MACRO

CLEAR

0108V2200_42-54_EN(U) 01.8.1, 2:53 PM49

REMOTE CONTROL FEATURES

Each Component Control Area

The general operational buttons are shown for each area. Some of them may not function depending on the component

you have. After setting the manufacturer code, press an input selector button, Å / ı, or SELECT k / n to select a

component you want to control.

■ Operating a DVD player (DVD area)

STANDBY

6CH INPUT

SOUND

SYSTEM

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AUX

POWER

100

11 12

234

STANDBY

6CH INPUT

SOUND

SYSTEM

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AUX

POWER

100

11 12

234

* TV VOL +/–, TV INPUT, and TV MUTE function to operate your TV without switching the input if the

manufacturer code is set in D-TV/LD or PHONO. When the manufacturer code for your TV is set up in the both D-

TV/LD and PHONO areas, priority is given to the signal in the D-TV/LD area.

■ Operating a VCR (VCR 1 and VCR 2/DVR areas)

* TV VOL +/–, TV INPUT, and TV MUTE function to operate your TV without switching the input if the

manufacturer code is set in D-TV/LD or PHONO. When the manufacturer code for your TV is set up in the both D-

TV/LD and PHONO areas, priority is given to the signal in the D-TV/LD area.

DISPLAY

DISC +/– (disc skip)

STOP

Title/Index

TITLE

Return

POWER

Menu cursor/ENTER

Audio

Skip search

PLAY

PAUSE

Numeric buttons

Clear

CH +/– (channel)

POWER

Record

(Press twice to start recording)

TV/Video input

STOP

PLAY

PAUSE

Numeric buttons

0108V2200_42-54_EN(U) 01.8.1, 9:44 AM50

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

REMOTE CONTROL FEATURES

STANDBY

6CH INPUT

SOUND

SYSTEM

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AUX

POWER

100

11 12

234

STANDBY

6CH INPUT

SOUND

SYSTEM

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AUX

POWER

100

11 12

234

■ Operating a TV/digital TV (D-TV/LD area) or a cable TV/satellite TV (CBL/

SAT area)

Set the manufacture code for your LD player following the setting procedure described on page 43 because TV is

factory-set for this input selector button.

* TV VOL +/–, TV INPUT, and TV MUTE function to operate your TV without switching the input if the

manufacturer code is set in PHONO.

* SEARCH, REC, STOP, PAUSE and PLAY function to operate your VCR without switching the input to VCR 1 if the

manufacturer code is set in VCR 1.

■ Operating an LD player (D-TV/LD area)

CH +/– (channel)

DISPLAY

POWER

Enter

TV INPUT

TV VOL +/–

TV MUTE

Numeric buttons

Clear

DISPLAY

POWER

STOP

Chapter/Time

SOUND

CHAPTER –/+ (chapter search)

PLAY

PAUSE

Numeric buttons

0108V2200_42-54_EN(U) 01.8.1, 9:44 AM51

REMOTE CONTROL FEATURES

STANDBY

6CH INPUT

SOUND

SYSTEM

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AUX

POWER

100

11 12

234

■ Operating a CD player (CD area)

STANDBY

6CH INPUT

SOUND

SYSTEM

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AUX

POWER

100

11 12

234

* TV VOL +/–, TV INPUT, and TV MUTE function to operate your TV without switching the input if the

manufacturer code is set in D-TV/LD or PHONO. When the manufacturer code for your TV is set up in the both D-

TV/LD and PHONO areas, priority is given to the signal in the D-TV/LD area.

■ Operating a CD recorder (CD-R area) or an MD recorder (MD/TAPE area)

* TV VOL +/–, TV INPUT, and TV MUTE function to operate your TV without switching the input if the

manufacturer code is set in D-TV/LD or PHONO. When the manufacturer code for your TV is set up in the both D-

TV/LD and PHONO areas, priority is given to the signal in the D-TV/LD area.

DISC +/– (disc skip)

DISPLAY

POWER

STOP

INDEX

Skip search

PLAY

PAUSE

Numeric buttons

Clear

DISPLAY

POWER

STOP

INDEX

(CD-R only)

Skip serch

PLAY

PAUSE

Numeric buttons

Clear

(CD-R only)

Record

(MD only)

0108V2200_42-54_EN(U) 01.8.1, 9:44 AM52

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

REMOTE CONTROL FEATURES

STANDBY

6CH INPUT

SOUND

SYSTEM

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AUX

POWER

100

11 12

234

■ Operating a tape deck (MD/TAPE area)

STANDBY

6CH INPUT

SOUND

SYSTEM

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AUX

POWER

100

11 12

234

* TV VOL +/–, TV INPUT, and TV MUTE function to operate your TV without switching the input if the

manufacturer code is set in D-TV/LD or PHONO. When the manufacturer code for your TV is set up in the both D-

TV/LD and PHONO areas, priority is given to the signal in the D-TV/LD area.

■ Operating a tuner (TUNER area)

SEARCH backward/forward

Record

STOP

INDEX

A/B

Direction A/B

PLAY

PAUSE

Numeric button

PRESET +/–

POWER

Preset group A

Preset group B

Preset group C

Preset group A/B/C/D/E

Preset number 1 to 8

Preset group E

Preset group D

0108V2200_42-54_EN(U) 01.8.1, 9:44 AM53

REMOTE CONTROL FEATURES

STANDBY

6CH INPUT

SOUND

SYSTEM

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AUX

POWER

100

11 12

234

■ Operating the component set in

Å or ı

These buttons are not input selector buttons but simply provide the space for an extra component to control with this

unit’s remote control without making connection to this unit. The shaded area shown below can be used for the

component set in Å and ı, and the function for each button differs depending on the component.

YAMAHA LD player is factory-set in Å and sattellite tuner in ı. However if you want to set other component, set the

manufacturer code for the component you want to set in the Å / ı button following the manufacturer code setting

procedure described on page 43.

The functions of these buttons in the

component control area differ for the

component you set in Å or ı.

0108V2200_42-54_EN(U) 01.8.1, 9:44 AM54

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

Adjusting the Items on the SET

Adjustment should be made with the remote control.

Note

• Some items require extra steps to change to the desired setting.

1 Set PARAMETER/SET

MENU to SET MENU.

2 Press k / n repeatedly to select the item (1 to

14) you want to adjust.

3 Press –/+ once to enter the setup mode of

the selected item.

The last setting you adjusted appears on the video

monitor or on the front panel display.

Depending on the item, press k / n to select a sub

item.

2 LOW FRQ TEST

≥ OUTPUT…MAIN L/R

FRQ……………………88Hz

TEST TONE………OFF

PARAMETER

SET MENU

ADVANCED OPERATION

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

PARAMETER

SET MENU

EFFECT

LEVEL

ON SCREEN

TESTSLEEP

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

100

11 12

234

2, 3, 5

3, 4

The SET MENU consists of 14 items including the

speaker mode setting, center graphic equalizer and

parameter initialization features. Choose the appropriate

item and adjust or select the values as necessary.

• You can adjust the items on the SET MENU while playing a

source.

• We recommend that you adjust the items on the SET MENU

while using a video monitor. It is easier to see the video

monitor than it is to see the front panel display on this unit

while adjusting the items.

Note

• The indication on the front panel display is the abbreviation of

the OSD.

1 SPEAKER SET

1A CENTER SP

1B MAIN SP

1C REAR L/R SP

1D REAR CT SP

1E LFE/BASS OUT

1F MAIN LEVEL

2 LOW FRQ TEST

3 L/R BALANCE

4 HP TONE CTRL

5 CENTER GEQ

6 INPUT RENAME

7 I/O ASSIGNMENT

7A CMPNT-V INPUT

7B OPTICAL OUT

7C OPTICAL IN

7D COAXIAL IN

8 INPUT MODE

9 PARAM. INI

10 LFE LEVEL

11 DYNAMIC RANGE

12 SP DELAY TIME

13 DISPLAY SET

14 MEMORY GUARD

2 LOW FRQ TEST

OUTPUT…MAIN L/R

FRQ……………………88Hz

≥ TEST TONE………OFF

SET MENU 1/4

≥ 2 LOW FRQ TEST

3 L/R BALANCE

4 HP TONE CTRL

/ : Up/Down

-/+ : Enter

1 SPEAKER SET

0109V2200_55-67_EN(U) 01.8.1, 9:44 AM55

SET MENU

LRG SML NONE

1A CENTER SP

4 Press –/+ repeatedly to change the setting of

the item.

5 Press k / n repeatedly until the current DSP

program appears or simply press one of the

DSP program group buttons to exit from the

SET MENU.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost even if this unit is in the standby

mode. However if the power cord is disconnected from

the AC outlet, or the power supply is cut for more than

one week, the stored data will be lost. If so, adjust the

items again.

2 LOW FRQ TEST

OUTPUT…MAIN L/R

FRQ……………………88Hz

≥ TEST TONE…………ON

LRG SML NONE

1A CENTER SP

LRG SML NONE

1A CENTER SP

HALL 1

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

100

11 12

234

1 SPEAKER SET (speaker mode

settings)

Use this feature to select suitable output modes for your

speaker configuration.

Notes

• When 96-kHz sampling digital signals are input to this unit,

level adjustments in items 1B,1E and 1F are possible, but those

in items 1A,1C and 1D are not affected.

• When 6CH INPUT is selected as the input source, level

adjustments in items 1A through 1E are not affected.

■ 1A CENTER SP (center speaker

mode)

By adding a center speaker to your speaker configuration,

this unit can provide good dialog localization for many

listeners and superior synchronization of sound and

images. The OSD shows a large, small or no center

speaker depending on how you set this item.

Choices: LRG (large), SML (small), NONE

Initial setting: LRG

LRG

Select this if you have a large center speaker. The entire

range of the center channel signal is directed to the center

speaker.

SML

Select this if you have a small center speaker. The low-

frequency signals (90 Hz and below) of the center

channel are directed to the speakers selected with “1E

LFE/BASS OUT”.

NONE

Select this if you do not have a center speaker. All of the

center channel signal are directed to the left and right

main speakers.

0109V2200_55-67_EN(U) 01.8.1, 9:44 AM56

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SET MENU

LARGE SMALL

1B MAIN SP

LRG SML NONE

1C REAR L/R SP

LRG SML NONE

1C REAR L/R SP

LRG SML NONE

1C REAR L/R SP

LARGE SMALL

1B MAIN SP

■ 1B MAIN SP (main speaker mode)

The OSD shows large or small main speakers depending

on how you set this item.

Choices: LARGE, SMALL

Initial setting: LARGE

LARGE

Select this if you have large main speakers. The entire

range of the left and right main channel signal is directed

to the left and right main speakers.

SMALL

Select this if you have small main speakers. The low-

frequency signals (90 Hz and below) of the main channel

are directed to the speakers selected with “1E LFE/BASS

OUT”.

Note

• When you select MAIN for “1E LFE/BASS OUT”, the low-

frequency signals (90 Hz and below) of the main channel are

directed to the main speakers even if you select SMALL for the

main speaker mode.

■ 1C REAR L/R SP (rear speaker

mode)

The OSD shows large, small or no rear speakers

depending on how you set this item.

Choices: LRG (large), SML (small), NONE

Initial setting: LRG

LRG

Select this if you have large left and right rear speakers or

if a rear subwoofer is connected to the rear speakers. The

entire range of the rear channel signal is directed to the

left and right rear speakers.

SML

Select this if you have small left and right rear speakers.

The low-frequency signals (90 Hz and below) of the rear

channel are directed to the speakers selected with “1E

LFE/BASS OUT”.

NONE

Select this if you do not have rear speakers.

• This unit is set in the virtual CINEMA DSP mode by selecting

NONE for “1C REAR L/R SP”.

0109V2200_55-67_EN(U) 01.8.1, 9:44 AM57

SET MENU

■ 1D REAR CT SP (rear center

speaker mode)

By adding a rear center speaker to your speaker

configuration, this unit can provide more realistic front-

to-back and transitions. The initial setting is “LRG”.

Choices: LRG (large), SML (small), NONE

Initial setting: LRG

LRG

Select this if you have a large rear center speaker. The

entire range of the rear center channel signal is directed to

the rear center speaker.

SML

Select this if you have a small rear center speaker. The

low-frequency signals (90 Hz and below) of the rear

center channel are directed to the speakers selected with

“1E LFE/BASS OUT”.

NONE

Select this if you do not have a rear center speaker. All of

the rear center channel signal are directed to the left and

right rear speakers.

■ 1E LFE/BASS OUT (bass out

mode)

LFE signals carry low-frequency effects when this unit

decodes a Dolby Digital or DTS signal. Low-frequency

signals are defined as 90 Hz and below. The Low-

frequency signals are directed to both main right and left

speakers, and the subwoofer (subwoofer can be used for

both stereo reproduction and the DSP program).

Choices: SWFR (subwoofer), MAIN, BOTH

Initial setting: BOTH

SWFR

Select this if you use a subwoofer. The LFE signals are

directed to the subwoofer.

MAIN

Select this if you do not use a subwoofer. The LFE signals

are directed to the main speakers.

BOTH

Select this if you use a subwoofer and you want to mix

the main channel low-frequency signals with the LFE

signals.

Note

• The low-frequency signals (90 Hz and below) from all main,

center, rear and rear center channels are directed to the LFE

channel when you select the small speaker setting in items 1A,

1B, 1C and 1D.

SWFR MAIN BOTH

1E LFE/BASS OUT

SWFR MAIN BOTH

1E LFE/BASS OUT

SWFR MAIN BOTH

1E LFE/BASS OUT

LRG SML NONE

1D REAR CT SP

LRG SML NONE

1D REAR CT SP

LRG SML NONE

1D REAR CT SP

0109V2200_55-67_EN(U) 01.8.1, 9:44 AM58

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SET MENU

Normal -10dB

1F MAIN LEVEL

Normal -10dB

1F MAIN LEVEL

2 LOW FRQ TEST

Use this feature to adjust the output level of the

subwoofer so it matches that of the other speakers in your

configuration. Change the setting with the remote control

while sitting in the listening position.

1 Press –/+ to set “TEST TONE” to ON, and

adjust the volume with VOLUME +/– so you

can hear the tone.

Notes

• Do not turn up the volume too high.

• If no test tone is heard, turn down the volume, set this unit in

the standby mode and make sure all the necessary connections

are correct.

2 Press n to go to “OUTPUT” and press –/+ to

select the speaker you want to compare with

the subwoofer.

If SWFR is selected, the test tone above 90 Hz will

not be output from the subwoofer. The test tone will

not necessarily be output from the selected speakers.

The output mode of the test tone depends on the

settings of “1 SPEAKER SET” on the SET MENU.

3 Press n to go to “FRQ” and press –/+ to

select the frequency you want to use.

■ 1F MAIN LEVEL (main level

mode)

Change this setting if you cannot match the output level

of the center, rear (L/R) and rear center speakers with the

main speakers because of the unusually high-efficiency

performance of the main speakers.

Choices: Normal, –10 dB

Initial setting: Normal

Normal

Select this if you can match the output level of your effect

speakers with that of your main speakers when using the

test tone.

–10 dB

Select this if you cannot match the output level of your

effect speakers with that of your main speakers when

using the test tone.

2 LOW FRQ TEST

OUTPUT…MAIN L/R

FRQ……………………88Hz

≥ TEST TONE…………ON

2 LOW FRQ TEST

≥ OUTPUT…MAIN L/R

FRQ……………………88Hz

TEST TONE………OFF

2 LOW FRQ TEST

OUTPUT…MAIN L/R

≥ FRQ……………………88Hz

TEST TONE………OFF

0109V2200_55-67_EN(U) 01.8.1, 9:44 AM59

SET MENU

5 CENTER GEQ

≥ 300Hz

1kHz

3kHz

10kHz

+3dB

100Hz

4 HP TONE CTRL (headphone tone

control)

Use this feature to adjust the level of the bass and treble

when you use your headphones.

Control range (dB): –6 to +3 for both BASS and TRBL

(treble)

Initial setting: 0 dB for both BASS and TRBL (treble)

5 CENTER GEQ (center graphic

equalizer)

Use this feature to adjust the built-in 5-band graphic

equalizer so that the center speaker tonal quality matches

that of the left and right main speakers. You can select the

100 Hz, 300 Hz, 1 kHz, 3 kHz, or 10 kHz frequencies.

Control range (dB): –6 to +6

Initial setting: 0 dB for 5-band

1 Press n to select a higher frequency and k

to select a lower frequency.

2 Press –/+ to adjust the level of that

frequency.

• You can monitor the center speaker sound while adjusting this

item by using the test tone. Press TEST before starting the

foregoing procedure. “TEST DOLBY SUR.” appears on the

video monitor, and the test tone starts alternating among the

speakers. Once you begin this procedure, the test tone remains

at the center speaker and you can hear how the sound changes

as you adjust the various frequency levels. To stop the test tone,

press TEST (see pages 23 and 24).

3 L/R BALANCE

-/+ : Adjust

/ : Exit

…………………… ……………………

4 HP TONE CTRL

TRBL

0dB

≥ BASS

5 CENTER GEQ

300Hz

1kHz

3kHz

10kHz

0dB

≥ 100Hz

4 Adjust the volume of the subwoofer with the

controls on the subwoofer so it matches that

of the speaker you are comparing it to.

■ About the test tone

The test tone is produced by the tone generator.

The tone generator produces a narrow-band noise

centered on a specified frequency by the band pass filter.

You can change this center frequency from 35 Hz through

250 Hz in one-sixth octave steps.

You can use the test tone not only for adjusting the

subwoofer level, but also for checking the low-frequency

characteristics of your listening room. Low-frequency

sounds are especially affected by the listener’s position,

speaker placement, subwoofer polarity and other

conditions.

Digital generator

(wide band noise produced)

Band pass filter

35 Hz – 250 HzCenter freq.

Freq.

Noise

3 L/R BALANCE (balance of the

left and right main speakers)

Use this feature to adjust the balance of the output level

from the left and right main speakers.

Control range: 10 steps for L/R

Initial setting: 0 dB for L/R

Press + to decrease the output level for the

left main speaker. Press – for the right main

speaker.

0109V2200_55-67_EN(U) 01.8.1, 9:44 AM60

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SET MENU

6 INPUT RENAME

Use this feature to change the name of the input which

appears on the OSD or the front panel display.

1 Press an input selector button (or use INPUT

l / h) to select the input you want to

change the name of.

2 Press –/+ to place the _ (under-bar) under

the space or the character you want to edit.

3 Press k / n to select the character you want

to use and –/+ to move to the next one.

• Press n to change the character in the following

order, or press k to go in the reverse order.

A to Z, a space, 0 to 9, a space, a to z, a space, #,

*, +, and so on.

• Follow the foregoing procedure to rename other

inputs.

Note

• You can use up to 8 characters to rename the inputs.

4 Press + repeatedly to exit from INPUT

RENAME.

6 INPUT RENAME

-/+ : Position

/ : Character

DVD ≥ DVD

6 INPUT RENAME

-/+ : Position

/ : Character

DVD ≥ DVD1

6 INPUT RENAME

-/+ : Position

/ : Character

DVD ≥ DVD

7A CMPNT-V INPUT

[B]……………D-TV/LD

≥ [A]…………… DVD

7B OPTICAL OUT

(2)…………… CD-R

≥ (1)……………MD/TAPE

7 I/O ASSIGNMENT

It is possible to assign jacks according to the component

to be used if this unit’s COMPONENT VIDEO input jack

or DIGITAL INPUT/OUTPUT jack settings (component

names for jacks) differ from that component. This makes

it possible to change the jack assignment and effectively

connect more component.

Once you assign, you can select that component with

INPUT l / h (the input selector buttons on the remote

control).

■ 7A CMPNT-V INPUT for

COMPONENT VIDEO INPUT jacks

[A] and [B]

Choices: [A] DVD, V-AUX, VCR 2/DVR, VCR 1,

CBL/SAT, D-TV/LD

[B] D-TV/LD, DVD, V-AUX, VCR 2/

DVR, VCR 1, CBL/SAT

Initial settings: [A] DVD

[B] D-TV/LD

■ 7B OPTICAL OUT for OPTICAL

OUTPUT jacks (1) and (2)

Choices: (1) MD/TAPE, CD-R, CD, PHONO,

V-AUX, VCR 2/DVR, VCR 1, CBL/

SAT, D-TV/LD, DVD

(2) CD-R, CD, PHONO, V-AUX, VCR 2/

DVR, VCR 1, CBL/SAT, D-TV/LD,

DVD, MD/TAPE

Initial settings: (1) MD/TAPE

(2) CD-R

0109V2200_55-67_EN(U) 01.8.1, 9:44 AM61

SET MENU

8 INPUT MODE (initial input

mode)

Use this feature to designate the input mode for sources

connected to the DIGITAL INPUT jacks when you turn

on this unit (see page 27 for details about the input

mode).

Choices: AUTO, LAST

Initial setting: AUTO

AUTO

Select this to allow this unit to automatically detect the

type of input signal and select the appropriate input mode.

LAST

Select this to set this unit to automatically select the last

input mode used for that source.

■ 7C OPTICAL IN for OPTICAL

INPUT jacks (3) to (6)

Choices: (3) CD, PHONO, VCR 2/DVR, VCR 1,

CBL/SAT, D-TV/LD, DVD, MD/

TAPE, CD-R

(4) CD-R, CD, PHONO, VCR 2/DVR,

VCR 1, CBL/SAT, D-TV/LD, DVD,

MD/TAPE

(5) DVD, MD/TAPE, CD-R, CD,

PHONO, VCR 2/DVR, VCR 1, CBL/

SAT, D-TV/LD

(6) D-TV/LD, DVD, MD/TAPE, CD-R,

CD, PHONO, VCR 2/DVR, VCR 1,

CBL/SAT

Initial settings: (3) CD

(4) CD-R

(5) DVD

(6) D-TV/LD

■ 7D COAXIAL IN for COAXIAL

INPUT jacks (7) and (8)

Choices: (7) CD, PHONO, V-AUX, VCR 2/DVR,

VCR 1, CBL/SAT, D-TV/LD, DVD,

MD/TAPE, CD-R

(8) CBL/SAT, D-TV/LD, DVD, MD/

TAPE, CD-R, CD, PHONO, V-AUX,

VCR 2/DVR, VCR 1

Initial settings: (7) CD

(8) CBL/SAT

Note

• You cannot select an item more than once for the same type of

jack.

7D COAXIAL IN

≥ (8)………CBL/SAT

(7)…………… CD

8 INPUT MODE

-/+ : Select

/ : Exit

AUTO LAST

7C OPTICAL IN

(4)…………… CD-R

≥ (5)…………… DVD

(6)……………D-TV/LD

(3)…………… CD

0109V2200_55-67_EN(U) 01.8.3, 7:39 PM62

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SET MENU

9 PARAM. INI (parameter

initialization)

Use this feature to initialize the parameters for each DSP

program within a DSP program group. When you

initialize a DSP program group, all of the parameter

values within that group revert to their initial settings.

Press the corresponding numeric button for

the DSP program that you want to initialize.

The asterisk (*) next to the program number means

that the parameter values have been changed.

Notes

• You cannot initialize the individual DSP programs within a

group separately.

• The parameter values of the DSP programs do not change if

you initialize a program group that does not have the asterisk

mark (*).

• When “14 MEMORY GUARD” is set to ON (see page 65),

you cannot initialize any program groups.

• Once you initialize a DSP program group, you cannot

automatically revert to the previous parameter settings.

10 LFE LEVEL

This setting is effective only when this unit decodes

Dolby Digital or DTS signals.

Use this feature to adjust the output level of the LFE

(low-frequency effect) channel when playing back a

Dolby Digital or DTS signal. The LFE signal carries the

low-frequency special effect sound which is only added to

certain scenes.

Control range (dB): –20 to 0 for both SPEAKER and

HEADPHONE

Initial setting: 0 dB for both SPEAKER and

HEADPHONE

1 Press k / n to select the item to be adjusted.

2 Press – to adjust the LFE level.

Note

• Adjust the LFE level according to the capacity of your

subwoofer or headphones.

9 PARAM. INI

* 5 678

9 *10 11

Press No. Key

1 23*4

10 LFE LEVEL

HEADPHONE…………0dB

≥ SPEAKER………………0dB

10 LFE LEVEL

HEADPHONE…………0dB

≥ SPEAKER…………-11dB

0109V2200_55-67_EN(U) 01.8.2, 9:35 AM63

SET MENU

12 SP DELAY TIME

Use this feature to adjust the delay of the Center and the

Rear Center channel sounds. This feature works when this

unit decodes DTS or Dolby Digital signals. Ideally, the

Center speaker and the Rear Center speaker should be the

same distance from the main listening position as the left

and right Main speakers. However, in most home

situations, the Center speaker or the Rear Center speaker

is placed in line with the Main speakers or the Rear

speakers. By delaying the sound from the Center speaker

and the Rear Center speaker, the apparent distance from

the Center speaker and the Rear Center speaker to the

main listening position can be adjusted to make it seem

the same as the distance between the left and right Main

speaker, and the left and right Rear speakers to the

listening position. Adjusting the delay time for the Center

speaker is especially important for giving depth to the

dialogue.

Control range: 0 to 5 ms for CENTER

0 to 30 ms for REAR CENTER

Initial setting: 0 ms for CENTER

3 ms for REAR CENTER

Press –/+ to increase or decrease the delay

of the center and the rear center channel

sounds.

Center speaker image

• Increasing the delay by 1 ms simulates moving the speakers

about 30 cm (one foot) farther away from the listening position.

11 D-RANGE (dynamic range)

Use this feature to adjust the dynamic range. This setting

is effective only when this unit decodes Dolby Digital

signals.

MAX

Select the “MAX” setting for feature films.

STD

Select the “STD” (Standard) setting for general use.

MIN

Select the “MIN” setting for listening to sources at

extremely low volume levels.

11 D-RANGE

HP: MAX STD MIN

≥ SP: MAX STD MIN

12 SP DELAY TIME

REAR CNTR…………3ms

≥ CENTER…………………0ms

0109V2200_55-67_EN(U) 01.8.1, 9:44 AM64

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SET MENU

13 DISPLAY SET

■ BLUE BACK

Selecting AUTO for the on-screen display setting displays

a blue background when there’s no video signal input.

Nothing is displayed on the screen including the on-

screen display if OFF is selected.

Choices: AUTO, OFF

Initial setting: AUTO

■ OSD SHIFT (OSD off-set position)

This setting is used to adjust the vertical position of the

OSD.

Control range: +5 (downward) to –5 (upward)

Initial setting: 0

Press + to lower the position of the OSD.

Press – to raise the position of the OSD.

■ DIMMER

You can adjust the brightness of the front panel display.

Control range: –4 to 0

Initial setting: 0

14 MEMORY GUARD

Use this feature to prevent accidental changes to DSP

program parameter values and other settings on this unit.

Choices: ON, OFF

Initial setting: OFF

Select ON to protect the following features:

• DSP program parameters

• All SET MENU items

• Center, rear speakers, rear center, and subwoofer levels

• The on-screen display (OSD) mode

Notes

• When “14 MEMORY GUARD” is set to ON, you cannot use

the test tone.

• When “14 MEMORY GUARD” is set to ON, you cannot select

any other SET MENU items.

13 DISPLAY SET

OSD SHIFT………………0

DIMMER………………………0

≥ BLUE BACK………AUTO

14 MEMORY GUARD

-/+ : Select

/ : Exit

OFF ON

0109V2200_55-67_EN(U) 01.8.1, 9:44 AM65

3 Press –/+ to adjust the speaker output level.

• The control range for the center, left and right rear

or rear center speakers is from +10 dB to –10 dB.

• The control range for the subwoofer is from 0 dB

to –20 dB.

• When PARAMETER/SET MENU is set to SET MENU, you

cannot adjust the output level by using LEVEL. However, each

time you press LEVEL, the current level of each speaker

appears on the front panel display and you can check the

speaker level.

Notes

• When the speaker output modes for “1A CENTER SP” and

“1C REAR L/R SP” are set to NONE, and “1E LFE/BASS

OUT” to MAIN, the output level of those speakers cannot be

adjusted because there is no sound coming from these speakers.

• When you adjust the output level with LEVEL, the settings you

made with the test tone will be changed.

• It is recommended to adjust the speakers (except for a

subwoofer) by following the steps described in Using the Test

Tone on pages 23 and 24.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost even if this unit is in the standby

mode. However if the power cord is disconnected from

the AC outlet, or the power supply is cut for more than

one week, the stored data will be lost. If so, set the

output level again.

You can adjust the output level of each effect speaker

(center, left and right rear, rear center and subwoofer)

while listening to a music source.

Adjustment should be made with the remote control.

1 Set PARAMETER/SET

MENU to PARAMETER.

2 Press LEVEL repeatedly to select the

speaker(s) you want to adjust.

Each time you press LEVEL, the selected speaker

changes and appears on the front panel display and

on the video monitor as follows: center, right rear,

rear center left rear and subwoofer.

LEVEL

PARAMETER

SET MENU

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

PARAMETER

SET MENU

EFFECT

LEVEL

ON SCREEN

TESTSLEEP

TV MUTE

A/B/C/D/E

LEVEL

ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS

• Once you press LEVEL, you can also select the speaker(s) to

be adjusted by pressing n/k.

Center speaker output level

Subwoofer output level

Left rear speaker output

level

Rear center speaker output

level

Right rear speaker output

level

0109V2200_55-67_EN(U) 01.8.1, 9:44 AM66

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

3 The “SLEEP” indicator soon lights up on the

front panel display after the sleep timer has

been set.

The display then returns to the previous indication.

Canceling the Sleep Timer

Press SLEEP repeatedly until “SLEEP OFF”

appears on the front panel display.

After a few seconds, “SLEEP OFF” disappears, the

“SLEEP” indicator goes off and the display returns

to the previous indication.

• The sleep timer setting can also be canceled by setting this unit

in the standby mode by using STANDBY on the remote control

(or STANDBY/ON on the front panel) or by disconnecting the

AC power cord from the AC outlet.

Use this feature to automatically set this unit in the

standby mode after the amount of time you have set. The

sleep timer is useful when you are going to sleep while

this unit is playing or recording a source. The sleep timer

also automatically turns off the external components

connected to AC OUTLET(S).

The sleep timer can only be set with the remote control.

• By connecting a commercially available timer to this unit, you

can also set a wake-up timer. Refer to the operation instructions

for the timer.

Setting the Sleep Timer

1 Select a source and start playback on the

source component.

2 Press SLEEP repeatedly

to set the amount of time

before this unit

automatically turns off.

Each time you press SLEEP, the front panel display

changes as shown below.

PHONO

DVD

VCR2/DVR

VCR 1

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

SLEEP

TRANSMIT

RE-NAME

STANDBY

6CH INPUT

SOUND

SYSTEM

CLEAR LEARN MACRO

OFF ON

MACRO

PHONO

DVD

VCR2/DVR

VCR 1

TITLE

CHAPTER

PAU SESTOPPOWER

REC

HALL 1

DSP

10KEY

HALL 2

CHURCH

JAZZ CLUB

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AU X

POWER

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

PARAMETER

SET MENU

EFFECT

LEVEL

ON SCREEN

TESTSLEEP

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

100

11 12

234

VCR DVD TUNER CD

PHONO

CD RV AUX

DSP

DIGITAL

VCR2/DVR

CBL

SAT

TAPE

VOLUME

SLEEP

SLEEP 120min

VCR DVD TUNER CD

PHONO

CD RV AUX

DSP

DIGITAL

VCR2/DVR

CBL

SAT

TAPE

VOLUME

SLEEP

CONCERT HALL1

SLEEP 120 min. SLEEP 90 min.

SLEEP 60 min.SLEEP 30 min.SLEEP OFF

SLEEP TIMER

SLEEP

0109V2200_55-67_EN(U) 01.8.1, 9:44 AM67

■ Example of a system configuration and connections

Notes

• When not using the main room, turn down the volume of this unit in the main room. Adjust the Zone 2 volume with the control on

the amplifier in the second room.

• DO NOT USE the Zone 2 feature for CDs encoded with DTS to avoid unexpected noise.

ZONE 2

You can make up a multi-room audio-video system with this unit. This feature enables you to set this unit to reproduce

separate input sources in the main room and second room (Zone 2) with the supplied remote control in the second room.

Only analog signals are sent to the second room. For any source you want to listen to in the second room, you must

connect the analog output jack from the source to the corresponding analog input jack on this unit.

Zone 2 Connections

To use the multi-room functions of this unit, you need the following additional equipment:

• An infrared signal receiver in the second room

• An infrared emitter in the main room

This emitter transmits the infrared signals from the remote control in the second room to the main room

(for example, to a CD player or LD player).

• An amplifier and speakers for the second room

• A video monitor for the second room

REMOTE CONTROL OUT

DVD INPUT

REMOTE CONTROL IN

ZONE 2 VIDEO OUT

ZONE 2 AUDIO OUT

OUT

REMOTE

CONTROL OUT

Main room

Infrared signal

receiver

Remote control

Second room

Amplifier

Infrared emitter

This unit

DVD player

(or other component)

This unit

• Since there are so many ways to connect and use this unit in a

multi-room installation, we recommend that you consult with

the nearest authorized YAMAHA dealer or service center for

the Zone 2 connections which will best meet your

requirements.

• Some YAMAHA models are able to connect directly to the

REMOTE CONTROL OUT jack of this unit. If you own these

products, you may not need to use an infrared emitter. Up to 6

YAMAHA components can be connected as shown.

Video

monitor

0110V2200_68-69_EN(U) 01.8.1, 9:44 AM68

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

ZONE 2

■ Special considerations when

using DTS software

The DTS signal is a digital bitstream. Therefore, if you

attempt to send the DTS signal to the second room, you

will only be able to hear the digital noise sound that could

damage your speakers.

Due to this characteristic of DTS encoded discs, the

following considerations and adjustments need to be

made.

For LDs or DVDs encoded with DTS

Only 2-channel analog audio signals may be sent to the

second room, as follows:

• LDs

Set your LD player’s left and right outputs to the

analog soundtrack.

• DVDs

Use the disc menu to set the DVD player’s mixed 2-

channel left and right audio outputs to the PCM or

Dolby Digital soundtrack.

For CDs encoded with DTS

DO NOT USE the Zone 2 feature for CDs encoded with

DTS to avoid unexpected noise.

Remote Control in Zone 2

In the second room (Zone 2), the supplied remote control

can be used for the Zone 2 remote control. You can select

the input source and control the component which is

located in the main room directly from the second room

regardless of the listening condition in the main room.

Before starting the following procedure, set REC OUT/

ZONE 2 on the front panel to SOURCE/REMOTE.

1 Repeat steps 1 and 2 of the procedure in

“Setting the Manufacturer Code” on page 43.

2 Press l / h to select “L:AMP”.

3 Press k / n to select “Zone2”.

4 Press LEARN to complete the Zone 2 setup.

5 Press SOURCE SELECT k to display

“Zone2” in the display window.

6 Press an input selector button to select the

input source you want to listen to in the

second room.

The display window shows “2: name of selected

input” if the remote control is in the Zone 2 mode.

7 You can control the component by using the

component control area buttons.

Note

• Adjust the Zone 2 volume with the control on the amplifier in

the second room.

8 Press SOURCE SELECT k / n to exit from

the Zone 2 mode.

ENTER

LEARN

SELECT

SOURCE

SELECT

SOURCE

6CH INPUT

SOUND

TITLE

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

EFFECT

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SOURCE

PLAY

– +

ENTER

100

11 12

234

PHONO

DVD

VCR2/DVR

VCR 1

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-A UX

0110V2200_68-69_EN(U) 01.8.1, 9:44 AM69

SOUND FIELD PROGRAM PARAMETER EDITING

What is a sound field?

What really creates the rich, full tones of a live instrument

are the multiple reflections from the walls of the room. In

addition to making the sound “live”, these reflections

enable us to tell where the player is situated, and the size

and shape of the room in which we are sitting.

■ Elements of a sound field

In any environment, in addition to the direct sound

coming straight to our ears from the player’s instrument,

there are two distinct types of sound reflections that

combine to make up the sound field:

Early reflections

Reflected sounds reach our ears extremely rapidly

(50 ms – 100 ms after the direct sound), after reflecting

from one surface only — for example, from the ceiling or

a wall. These reflections fall into specific patterns as

shown in the diagram on page 73 for any particular

environment, and provide vital information to our ears.

Early reflections actually add clarity to the direct sound.

Reverberations

These are caused by reflections from more than one

surface — walls, ceiling, the back of the room — so

numerous that they merge together to form a continuous

sonic “afterglow”. They are non-directional, and lessen

the clarity of the direct sound.

Direct sound, early reflections and subsequent

reverberation taken together help us to determine the

subjective size and shape of the room, and it is this

information that the digital sound field processor

reproduces in order to create sound fields.

If you could create the appropriate early reflections and

subsequent reverberations in your listening room, you

would be able to create your own listening environment.

The acoustics in your room could be changed to those of

a concert hall, a dance floor, or virtually any size room at

all. This ability to create sound fields at will is exactly

what YAMAHA has done with the digital sound field

processor.

Sound Field Program Parameters

DSP programs consist of some parameters to determine

the apparent room size, reverberation time, distance from

you to the performer, etc. In each program, these

parameters are set with values precisely calculated by

YAMAHA to create a sound field unique to the program.

It is recommended to use DSP programs without

changing the values of parameters; however, this unit also

allows you to create your own sound fields. Starting with

one of the built-in programs, you can adjust those

parameters.

Each DSP program has a set of parameters that allow you

to change the characteristics of the acoustic environment

to precisely create the effect you want. These parameters

correspond to the many natural acoustic factors that create

the sound field you experience in an actual concert hall or

other listening environment. The size of the room, for

example, affects the length of time between the early

reflections. The “ROOM SIZE” parameter provided in

many of the DSP programs alters the timing between

these reflections, thus changing the shape of the “room”

you are listening. In addition to room size, the shape of

the room and the characteristics of its surfaces have a

significant effect on the final sound. Surfaces that absorb

sound, for example, cause the reflections and

reverberations to die out more quickly, while highly

reflective surfaces allow the reflections to carry on for a

longer period of time. The digital sound field parameters

allow you to control these and many other factors that

contribute to your personal sound field, allowing you to

essentially “redesign” the concert halls, theaters, etc.

provided to create custom-tailored listening environments

that ideally match your mood and music.

See “Digital Sound Field Parameter Descriptions” on

pages 72 to 75.

0111V2200_70-75_EN(U) 01.8.1, 9:44 AM70

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SOUND FIELD PROGRAM PARAMETER EDITING

4 Press k / n to select the

parameter.

5 Press –/+ to change the

parameter value.

• When you set the parameter to a value other than the factory-

set value, an asterisk mark (*) appears by the parameter name

on the video monitor.

6 Repeat steps 3 to 5 above as necessary to

change other program parameters.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost even if this unit is set in the standby

mode, the power cord is disconnected from the AC

outlet, or the power supply is temporarily cut due to

power failure. However, if the power is cut for more

than one week, the parameter value you edited will

return to the factory setting. If so, edit the parameter

value again.

Resetting a Parameter to the

Factory-set Value

■ To reset some of the parameters

to the factory-set values

Select the parameter you want to reset. Then press and

hold –/+ until the value temporarily stops at the factory-

set value. The asterisk mark (*) by the parameter name

disappears on the video monitor.

■ To reset all of the parameters to

the factory-set values

Use “9 PARAM. INI” on the SET MENU to reset all of

the parameter values of all DSP programs within the

selected group to the factory-set values (see page 63).

This operation resets all of the parameter values of all

DSP programs within that group to the factory-set values.

Notes

• The available parameters may be displayed on more than one

OSD page for some of the programs. To scroll through pages,

press k / n.

• You cannot change parameter values when “14 MEMORY

GUARD” on the SET MENU is set to ON. If you want to

change the parameter values, set “14 MEMORY GUARD” to

OFF (see page 65).

Changing Parameter Settings

You can enjoy good quality sound with the factory-set

parameters. Although you do not have to change the

initial settings, you can change some of the parameters to

better suit the input source or your listening room.

Adjustments should be made with the remote control.

• We recommended that you edit the parameter while using a

video monitor. It is easier to see the video monitor than it is to

see the front panel display.

1 Set PARAMETER/SET

MENU to PARAMETER.

2 Turn on the video monitor

and press ON SCREEN

repeatedly to select the

full display mode.

3 Select a DSP program you want to adjust.

PARAMETER

SET MENU

P05 ROCK CONCERT

ROOM SIZE…………1.0

LIVENESS…………………5

REV.TIME…………1.6s

REV.DELAY……120ms

REV.LEVEL……………7%

≥ INIT.DLY…………15ms

HALL 1

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

100

11 12

234

ON SCREEN

Program No.

Example of the parameter setting display

Parameters

Cursor

Program name

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

PRESET

DISC

PARAMETER

SET MENU

EFFECT

LEVEL

ON SCREEN

TESTSLEEP

TV MUTE

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

100

11 12

234

Parameter valves

0111V2200_70-75_EN(U) 01.8.1, 9:44 AM71

Large value = 2.0Small value = 0.1

Sound Source

TimeTimeTime

Early

Reflections

Sound Source

Level

■ ROOM SIZE

[P. ROOM SIZE for the presence sound field] Control Range 0.1 – 2.0

Function: This parameter adjusts the apparent size of the surround sound field. The larger the value, the larger the

surround sound field becomes.

Description: As the sound is repeatedly reflected around a room, the larger the hall is, the longer the time between

the original reflected sound and the subsequent reflections. By controlling the time between the

reflected sounds, you can change the apparent size of the virtual venue. Changing this parameter from

one to two, doubles the apparent length of the room.

Large value = 99 msSmall value = 1 ms

Reflection Face

Sound Source

TimeTime Time

INIT.DLYINIT.DLYINIT.DLY

Early

Reflections

Sound Source

Level

DIGITAL SOUND FIELD PARAMETER DESCRIPTIONS

You can adjust the values of certain digital sound field parameters so the sound fields are recreated accurately in your

listening room. Not all of the following parameters are found in every program.

■ INIT. DLY (Initial Delay)

[P. INT. DLY for the presence sound field] Control Range 1 – 99 msec

Function: This parameter changes the apparent distance from the source sound by adjusting the delay between the

direct sound and the first reflection heard by the listener.

Description: The smaller the value, the closer the sound source seems to the listener. The larger the value, the farther

the apparent distance seems. For a small room, this parameter would be set to a small value, and for a

large room, it would be set to a large value.

0111V2200_70-75_EN(U) 01.8.1, 9:44 AM72

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SOUND FIELD PROGRAM PARAMETER EDITINGDIGITAL SOUND FIELD PARAMETER DESCRIPTIONS

■ S. DELAY (Surround Delay) Control Range 0 – 49 msec (The range

depends on the signal format.)

Function: This parameter adjusts the delay between the direct sound and the surround sound.

■ S. INIT. DLY (Surround Initial Delay) Control Range 1 – 49 msec

Function: This parameter adjusts the delay between the direct sound and the first reflection on the surround side

of the sound field. You can only adjust this parameter when at least two front channels and two rear

channels are used.

■ S. ROOM SIZE (Surround Room Size) Control Range 0.1 – 2.0

Function: This parameter adjusts the apparent size of the surround sound field.

■ S. LIVENESS (Surround Liveness) Control Range 0 –10

Function: This parameter adjusts the apparent reflectivity of the virtual walls in the surround sound field.

■ RC. INIT. DLY (Rear Center Initial Delay) Control Range 1 – 49 msec

Function: This parameter adjusts the delay between the direct sound and the first reflection in the rear center

sound field.

■ RC. ROOM SIZE (Rear Center Room Size) Control Range 0.1 – 2.0

Function: This parameter adjusts the apparent size of the rear center sound field.

■ RC. LIVENESS (Rear Center Liveness) Control Range 0 – 10

Function: This parameter adjusts the apparent reflectivity of the virtual wall in the rear center sound field.

Large value = 10Small value = 0

Large

Reflected Sound

Small Reflected

Sound

Sound Source

Live

TimeTimeTime

Dead

Sound Source

Level

■ LIVENESS Control Range 0 – 10

Function: This parameter adjusts the reflectivity of the virtual walls in the hall by changing the rate at which the

early reflections decay.

Description: The early reflections of a sound source decay much faster in a room with acoustically absorbent wall

surfaces than in one which has highly reflective surfaces. A room with acoustically absorbent surfaces

is referred to as “dead”, while a room with highly reflective surfaces is referred to as “live”. The

LIVENESS parameter lets you adjust the early reflection decay rate, and thus the “liveness” of the

room.

0111V2200_70-75_EN(U) 01.8.1, 9:44 AM73

DIGITAL SOUND FIELD PARAMETER DESCRIPTIONS

60 dB 60 dB 60 dB

(dB)

60 dB

Level

Time

REV. LEVEL

Sound Source

■ REV. LEVEL (Reverberation Level) Control Range 0 – 100 %

Function: This parameter adjusts the volume of the reverberation sound.

Description: The larger the value, the stronger the reverberation becomes.

Time

REV. TIMEREV.

DELAY

Reverberation

Sound Source

Level

■ REV. DELAY (Reverberation Delay) Control Range 0 – 250 msec

Function: This parameter adjusts the time difference between the beginning of the direct sound and the beginning

of the reverberation sound.

Description: The larger the value, the later the reverberation sound begins. A later reverberation sound makes you

feel like you are in a larger acoustic environment.

Large value = 5.0 sSmall value = 1.0 s

Long

Reverberation

Short

Reverberation

Sound Source

REV. TIMEREV. TIMEREV. TIME

Early Reflections

ReverberationSound SourceReverberation

■ REV. TIME (Reverberation Time) Control Range 1.0 – 5.0 sec

Function: This parameter adjusts the amount of time it takes for the dense, subsequent reverberation sound to

decay by 60 dB (at 1 kHz). This changes the apparent size of the acoustic environment over an

extremely wide range.

Description: Set a longer reverberation time for “dead” sources and listening room environments, and a shorter time

for “live” sources and listening room environments.

0111V2200_70-75_EN(U) 01.8.1, 9:44 AM74

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SOUND FIELD PROGRAM PARAMETER EDITINGDIGITAL SOUND FIELD PARAMETER DESCRIPTIONS

For 6ch Stereo

■ CT LEVEL (Center Level) Control Range 0 – 100 %

Function: These parameters adjust the volume level for each channel in 6-channel stereo mode.

■ RL LEVEL (Rear Left Level) Control Range 0 – 100 %

Function: These parameters adjust the volume level for each channel in 6-channel stereo mode.

■ RR LEVEL (Rear Right Level) Control Range 0 – 100 %

Function: These parameters adjust the volume level for each channel in 6-channel stereo mode.

■ RC LEVEL (Rear Center Level) Control Range 0 – 100 %

Function: These parameters adjust the volume level for each channel in 6-channel stereo mode.

For PRO LOGIC Music

■ PANORAMA Control Range OFF/ON

Function: Extends the front stereo image to include the surround speakers for wraparound effect.

■ DIMENSION Control Range –3 – STD – +3

Function: Gradually adjusts the soundfield either towards the front or towards the rear.

■ CT WIDTH (Center Width) Control Range 0 – 7

Function: Adjusts the center image from all three front speakers to varying degrees.

0111V2200_70-75_EN(U) 01.8.1, 9:44 AM75

TROUBLESHOOTING

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed

below or if the instruction below does not help, set this unit in the standby mode, disconnect the power cord, and contact

the nearest authorized YAMAHA dealer or service center.

■ General

Problem

This unit fails to turn

on when STANDBY/

ON (or SYSTEM

POWER) is pressed,

or enters in the

standby mode soon

after the power has

been turned on.

On-screen display

does not appear.

No sound and/or no

picture.

The picture does not

appear.

The sound suddenly

goes off.

Cause

The power cord is not connected or the

plug is not completely inserted.

The IMPEDANCE SELECTOR switch

on the rear panel is not fully set to the

left or right position.

The protection circuitry has been

activated.

The setting for the on-screen display is

set to “DISPLAY OFF”.

The BLUE BACK setting under “9

DISPLAY SET” on the SET MENU is

set to OFF, and no video signal is input

to this unit.

Incorrect input or output cable

connections.

An appropriate input source has not been

selected.

The speaker connections are not secure.

The main speakers to be used have not

been selected properly.

The volume is turned down.

The sound is muted.

Digital signals other than PCM audio,

Dolby Digital or DTS signal which this

unit cannot reproduce are being input to

this unit by playing a CD-ROM, etc.

The output and input for the picture are

connected to different types of video

jacks.

The protection circuit has been activated

because of a short circuit, etc.

The sleep timer has functioned.

The sound is muted.

Remedy

Firmly connect the power cord.

Set the switch fully to the left or right position when

this unit is in the standby mode.

Make sure all speaker wire connections on this unit

and on all speakers are secure and that the wire for

each connection does not touch anything other than

its respective connection.

Select the full display or short display mode.

Set BLUE BACK to AUTO to always show the

OSD.

Connect the cables properly. If the problem persists,

the cables may be defective.

Select an appropriate input source with INPUT l /

h or 6CH INPUT (or the input selector buttons).

Secure the connections.

Select the main speakers with SPEAKERS A and/or

Turn up the volume.

Press MUTE or any operation buttons of this unit to

cancel a mute and adjust the volume.

Play a source whose signals this unit can reproduce.

Make connections using the same type of jack

(between composites, S-VIDEOs, or components)

for both the input and output.

Check the IMPEDANCE SELECTOR switch is set

to the appropriate position and then turn this unit

back on.

Check the speaker wires are not touching each other

and then turn this unit back on.

Turn on the power, and play the source again.

Press MUTE or any operation buttons of this unit to

cancel a mute and adjust the volume.

Refer

to page

11 – 18

11, 12

—

14, 15

—

0112V2200_76-83_EN(U) 01.8.1, 9:44 AM76

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

TROUBLESHOOTING

Problem

Only the speaker on

one side can be

heard.

No sound from the

effect speakers.

No sound from the

center speaker.

No sound from the

rear speakers.

No sound from the

subwoofer.

Poor bass

reproduction.

No sound from the

rear center speaker.

A “humming” sound

can be heard.

Cause

Incorrect cable connections.

Incorrect setting of “3 L/R BALANCE”

on the SET MENU.

The sound effect is off.

A Dolby Surround, Dolby Digital or

DTS decoding DSP program is being

used with material not encoded with

Dolby Surround, Dolby Digital or DTS.

A 96-kHz sampling digital signal is

being input to this unit.

The output level of the center speaker is

set to minimum.

“1A CENTER SP” on the SET MENU is

set to NONE.

One of the Hi-Fi DSP programs (1 to 6

except for Game) has been selected.

The source encoded with a Dolby Digital

or DTS signal does not have a center

channel signal.

The output level of the rear speakers is

set to minimum.

A monaural source is being played with

the program 11.

“1E LFE/BASS OUT” on the SET

MENU is set to MAIN when a Dolby

Digital or DTS signal is being played.

“1E LFE/BASS OUT” on the SET

MENU is set to SWFR or MAIN when a

2-channel source is being played.

The source does not contain low bass

signals (90 Hz and below).

“1E LFE/BASS OUT” on the SET

MENU is set to SWFR or BOTH and

your system does not include a

subwoofer.

The output mode for each speaker (main,

center, rear, or rear center) on the SET

MENU does not match your speaker

configuration.

“1D REAR CT SP” on the SET MENU

is set to NONE.

6.1/ES is not on.

Incorrect cable connections.

No connection from the turntable to the

GND terminal.

Remedy

Connect the cables properly. If the problem persists,

the cables may be defective.

Adjust it to the appropriate position.

Press STEREO to turn it on.

Select another DSP program.

Raise the level of the center speaker.

Select the appropriate mode for your center speaker.

Select another DSP program.

Raise the output level of the rear speakers.

Select another DSP program.

Select SWFR or BOTH.

Select BOTH.

Select MAIN.

Select the appropriate output mode for each speaker

based on the size of the speakers in your

configuration.

Select LRG or SML.

Press the 6.1/ES button on the remote control to turn

it on.

Firmly connect the audio plugs. If the problem

persists, the cables may be defective.

Connect the grounding cord of your turntable to the

GND terminal of this unit.

Refer

to page

28 – 35

—

34 , 35

—

56 – 59

29, 30

11 – 18

16, 17

0112V2200_76-83_EN(U) 01.8.1, 9:44 AM77

TROUBLESHOOTING

Problem

The volume level is low

while playing a record.

The volume level

cannot be increased, or

the sound is distorted.

The sound effect

cannot be recorded.

A source cannot be

recorded by a digital

recording component

connected to the

DIGITAL OUTPUT jack

of this unit.

The sound field

parameters and some

other settings on this

unit cannot be

changed.

This unit does not

operate properly.

“CHECK SP WIRES”

appears on the front

panel display.

The sound is degraded

when listening with

headphones connected

to a tape deck or CD

player that is connected

to this unit.

There is noise

interference from digital

or high-frequency

equipment, or this unit.

This unit suddenly

turns into the standby

mode.

Cause

The record is being played on a turntable

with an MC cartridge.

The component connected to the OUT

(REC) jacks of this unit is turned off.

It is not possible to record the sound

effect by a recording component.

A source component is only connected to

the analog input jacks of this unit.

“14 MEMORY GUARD” on the SET

MENU is set to ON.

The internal microcomputer has been

frozen by an external electric shock (such

as lightning or excessive static electricity)

or by a power supply with low voltage.

Speaker cables are short circuited.

This unit is in the standby mode.

This unit is too close to the digital or

high-frequency equipment.

The internal temperature becomes too

high and the overheat protection circuitry

has been activated.

Remedy

The turntable should be connected to this unit

through an MC-head amplifier.

Turn on the power to the component.

Connect the source component to the digital

input jacks of this unit.

Select OFF.

Disconnect the AC power cord from the outlet

and then plug it in again after about 30 seconds.

Make sure all speaker cables are connected

correctly.

Turn on the power of this unit.

Move this unit further away from such

equipment.

Wait until this unit cools down and then turn it

back on.

Refer

to page

16, 17

15 – 18

—

0112V2200_76-83_EN(U) 01.8.1, 9:44 AM78

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

TROUBLESHOOTING

■ Tuner

FM stereo reception is

noisy.

There is distortion, and

clear reception cannot

be obtained even with a

good FM antenna.

The desired station

cannot be tuned in with

the automatic tuning

method.

Previously preset

stations can no longer

be tuned in.

The desired station

cannot be tuned in with

the automatic tuning

method.

There are continuous

crackling and hissing

noises.

There are buzzing and

whining noises

(especially in the

evening).

Problem

Cause

The characteristics of FM stereo

broadcasts may cause this problem

when the transmitter is too far away or

the antenna input is poor.

There is multipath interference.

The station is too weak.

This unit has been disconnected for a

long period.

The signal is weak or the antenna

connections are loose.

Noises result from lightning,

fluorescent lamps, motors, thermostats

and other electrical equipment.

A TV set is being used nearby.

Remedy

Check the antenna connections.

Try using a high-quality directional FM

antenna.

Use the manual tuning method.

Adjust the antenna position to eliminate

multipath interference.

Use the manual tuning method.

Use a high-quality directional FM antenna.

Re-store the stations.

Tighten the AM loop antenna connections

and orient it for best reception.

Use the manual tuning method.

Use an outdoor antenna and a ground wire.

This will help somewhat, but it is difficult to

eliminate all noise.

Move this unit away from the TV.

Refer

to page

36, 37

—

0112V2200_76-83_EN(U) 01.8.1, 9:44 AM79

TROUBLESHOOTING

■ Remote control

Problem

The remote control

does not work nor

function properly.

The remote control

does not “learn” new

functions.

Continuous functions

such as volume

adjustment are learned,

but operate only for a

moment before

stopping.

Cause

Wrong distance or angle.

Direct sunlight or lighting (from an

inverter type of fluorescent lamp, etc.) is

striking the remote control sensor of this

unit.

The batteries are weak.

The internal microcomputer has

“frozen”.

The batteries of this remote control and/

or the other remote control are too weak.

The distance between the two remote

controls is too much or too little.

The signal coding or modulation of the

other remote control is not compatible

with this remote control.

Memory capacity is full.

The internal microcomputer has

“frozen”.

The learning process is incomplete.

Remedy

The remote control will function within a

maximum range of 6 m (20 feet) and no more

than 30 degrees off-axis from the front panel.

Reposition this unit.

Replace all batteries with new ones and press

RESET.

Remove the batteries from the battery

compartment once and then put them back.

Replace the batteries.

Place the remote controls at the proper distance.

Learning is not possible.

Further learning is not possible without deleting

unnecessary functions.

Remove the batteries from the battery

compartment once and then put them back.

Be sure to press and hold the function button on

the other remote control until “OK” appears in

the display window.

Refer to

page

—

47, 48

After this unit has been exposed to a strong external electric shock (such as lightning and strong static electricity) or if

you mishandle the operation of this unit, it may not function properly. In these cases, set this unit in the standby mode,

disconnect the power cord, plug it back in after 30 seconds, and start operating.

0112V2200_76-83_EN(U) 01.8.1, 9:44 AM80

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

GLOSSARY

■ Dolby Surround

Dolby Surround uses a four analog channel recording

system to reproduce realistic and dynamic sound effects:

two left and right main channels (stereo), a center channel

for dialog (monaural), and a rear channel for special

sound effects (monaural). The rear channel reproduces

sound within a narrow frequency range.

Dolby Surround is widely used with nearly all video tapes

and laser discs, and in many TV and cable broadcasts as

well. The Dolby Pro Logic decoder built into this unit

employs a digital signal processing system that

automatically stabilizes the volume on each channel to

enhance moving sound effects and directionality.

■ Dolby Digital

Dolby Digital is a digital surround sound system that

gives you completely independent multi-channel audio.

With three front channels (left, center and right), and two

rear stereo channels, Dolby Digital provides five full-

range audio channels. With an additional channel

especially for bass effects, called LFE (low frequency

effect), the system has a total of 5.1 channels (LFE is

counted as 0.1 channel).

Using two-channel stereo for the rear speakers, more

accurate moving sound effects and surround sound

environment are possible than with Dolby Surround. The

wide dynamic range (from maximum to minimum

volume) reproduced by the five full-range channels and

the precise sound orientation generated using digital

sound processing provide listeners with previously

unheard of excitement and realism.

With this unit, any sound environment from monaural up

to a 5.1-channel configuration can be freely selected for

your enjoyment.

■ Dolby Pro Logic

Dolby Pro Logic is the improved technique to decode

vast numbers of existing Dolby Surround programs. This

new technology enables a discrete 5-channel playback

with two left and right main channels, a center channel,

and two left and right rear channels compared with one

limited rear channel for the conventional Pro Logic

technology. Also the music mode is available for 2-

channel sources in addition to the movie mode.

■ DTS (Digital Theater Systems)

Digital Surround

DTS digital surround was developed to replace the analog

soundtracks of movies with a six-channel digital sound

track, and is now rapidly gaining popularity in movie

theaters around the world. Digital Theater Systems Inc.

has developed a home theater system so that you can

enjoy the depth of sound and natural spatial

representation of DTS digital surround in your home.

This system is practically distortion-free, clear 6-channel

sound (technically, a left, right and center channels, two

rear channels, plus an LFE 0.1 channel as a subwoofer,

for a total of 5.1 channels).

■ Neo: 6

Neo: 6 decodes the conventional 2-channel sources for 6

channel playback by the specific decoder. It enables

playback with the full-range channels with higher

separation just like digital discrete signal playback. Two

modes are available; “Music mode” for playing music

sources and “Cinema mode” for movies.

■ LFE 0.1 channel

This channel is for the reproduction of low bass signals.

The frequency range for this channel is 20 Hz to 120 Hz.

This channel is counted as 0.1 because it only enforces a

low frequency range compared to the full-range

reproduced by the other 5 channels in a Dolby Digital or

DTS 5.1 channel systems.

■ CINEMA DSP

DIGITAL

Since the Dolby Surround and DTS systems were

originally designed for use in movie theaters, their effect

is best felt in a theater having many speakers and

designed for acoustic effects. Since home conditions,

such as room size, wall material, number of speakers, and

so on, can differ so widely, it’s inevitable that there are

differences in the sound heard as well. Based on a wealth

of actually measured data, YAMAHA CINEMA DSP uses

YAMAHA original sound field technology to combine

Dolby Pro Logic, Dolby Digital and DTS systems to

provide the visual and audio experience of movie theater

in the listening room of your own home.

■ SILENT CINEMA

YAMAHA has developed a natural, realistic sound effect

DSP algorithm for headphones.

Parameters for headphones have been set for each sound

field so that accurate representations of all the sound field

programs can be enjoyed on headphones.

0112V2200_76-83_EN(U) 01.8.1, 9:44 AM81

GLOSSARY

■ Virtual CINEMA DSP

YAMAHA has developed a virtual CINEMA DSP

algorithm that allows you to enjoy DSP sound field

surround effects even without any rear speakers by using

virtual rear speakers.

It is even possible to enjoy virtual CINEMA DSP in a

minimum two-speaker system that does not include a

center speaker.

■ S VIDEO signal

With S VIDEO signal system, the video signal normally

transmitted using a pin cable is separated and transmitted

as the Y signal for the luminance and the C signal for the

chrominance through the S VIDEO cable. Using the S

VIDEO jack eliminates video signal transmission loss and

allows recording and playback of even more beautiful

images.

■ Component video signal

With the component video signal system, the video signal

is separated into the Y signal for the luminance and the

and P

signals for the chrominance. Color can

be reproduced more faithfully with this system because

each of these signals is independent. The component

signal is also called the “color difference signal” because

the luminance signal is subtracted from the color signal.

A monitor with component input jacks is required in

order to use the component signal for output.

■ PCM (Linear PCM)

Linear PCM is a signal format under which an analog

audio signal is digitized, recorded and transmitted without

using any compression. This is used as a method of

recording CDs and DVD audio. The PCM system uses a

technique for sampling the size of the analog signal per

very small unit of time. Standing for “pulse code

modulation”, the analog signal is encoded as pulses and

then modulated for recording.

■ Sampling frequency and number

of quantized bits

When digitizing an analog audio signal, the number of

times the signal is sampled per second is called the

sampling frequency, while the degree of fineness when

converting the sound level into a numeric value is called

the number of quantized bits.

The range of rates that can be played back is determined

based on the sampling rate, while the dynamic range

representing the sound level difference is determined by

the number of quantized bits. In principle, the higher the

sampling frequency, the wider the range of frequencies

that can be played back, and the higher the number of

quantized bits, the more finely the sound level can be

reproduced.

■ I/O assignment (SET MENU)

Although component is normally connected according to

jack names shown on the rear panel, this unit includes a

function that assigns jacks according to the component

being connected. If the component being used differs

from the component name shown for this unit’s

component video input jacks or digital input/output jacks,

it is possible to assign jacks according to the component

being connected. This makes it possible to change the

jack assignment and effectively connect more component.

0112V2200_76-83_EN(U) 01.8.1, 9:44 AM82

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPECIFICATIONS

AUDIO SECTION

• Minimum RMS Output Power for Main, Center, Rear

20 Hz to 20 kHz, 0.04% THD, 8 Ω ..................................... 100 W

1 kHz, 0.04% THD, 8 Ω ...................................................... 105 W

• Maximum Power (EIAJ)

[China and General models]

1 kHz, 10% THD, 8 Ω ......................................................... 150 W

• Dynamic Power (IHF)

8/6/4/2 Ω ........................................................ 130/160/200/245 W

• Damping Factor

20 Hz to 20 kHz, 8 Ω ................................................... 80 or more

• Frequency Response

CD to Main L/R ...................................... 10 Hz to 100 kHz, –3 dB

• Total Harmonic Distortion

20 Hz to 20 kHz, 50 W, 8 Ω, Main L/R ................................0.04%

• Signal to Noise Ratio (IHF-A Network)

PHONO MM to REC OUT (5 mV, shorted)

[U.S.A., Canada, China and General models] ...................... 86 dB

[Other models] ...................................................................... 81 dB

CD (250 mV, shorted) to Main L/R, Effect Off .................. 100 dB

• Residual Noise (IHF-A Network)

Main L/R ................................................................ 150 µV or less

• Channel Separation (1 kHz/10 kHz)

CD (5.1 kΩ terminated) to Main L/R ........................ 60 dB/45 dB

• Tone Control (Main L/R)

BASS Boost/Cut ...................................................... ±10 dB/50 Hz

TREBLE Boost/Cut ............................................... ±10 dB/20 kHz

BASS EXTENSION .................................................. +6 dB/60 Hz

• Phones Output ........................................................... 150 mV/100 Ω

• Input Sensitivity

CD, etc .................................................................... 150 mV/47 kΩ

PHONO ................................................................... 2.5 mV/47 kΩ

6CH INPUT .................................................... 150 mV/40 – 47 kΩ

• Output Level

REC OUT .............................................................. 150 mV/0.9 kΩ

PRE OUT .................................................................. 2.6 V/1.2 kΩ

SUBWOOFER .......................................................... 4.0 V/1.2 kΩ

VIDEO SECTION

• Video Signal Type ...................................................... NTSC or PAL

• Composite Video Signal Level ...................................... 1 Vp-p/75 Ω

• S-Video Signal Level

Y ................................................................................. 1 Vp-p/75 Ω

C .......................................................................... 0.286 Vp-p/75 Ω

• Component Video Signal Level

Y ................................................................................. 1 Vp-p/75 Ω

, P

............................................................. 0.7 Vp-p/75 Ω

• Signal to Noise Ratio ............................................................... 50 dB

• Frequency Response (MONITOR OUT)

Composite, S-Video ................................. 5 Hz to 10 MHz, –3 dB

Component ................................................. DC to 60 MHz, –3 dB

FM SECTION

• Tuning Range

[U.S.A. and Canada models] ............................ 87.5 to 107.9 MHz

[Other models] .............................................. 87.50 to 108.00 MHz

• 50 dB Quieting Sensitivity (IHF, 100% mod.)

Mono/Stereo ........................ 2.0 µV (17.3 dBf) /25 µV (39.2 dBf)

• Selectivity (400 kHz) ............................................................... 70 dB

• Signal to Noise Ratio (IHF)

Mono/Stereo .............................................................. 76 dB/70 dB

• Harmonic Distortion (1 kHz)

Mono/Stereo ................................................................. 0.2%/0.3%

• Stereo Separation (1 kHz) ....................................................... 45 dB

• Frequency Response ........................... 20 Hz to 15 kHz +0.5, –2 dB

AM SECTION

• Tuning Range ......................................... 530/531 to 1710/1611 kHz

• Usable Sensitivity ............................................................. 300 µV/m

GENERAL

• Power Supply

[U.S.A. and Canada models] ............................... AC 120 V/60 Hz

[Australia model] ................................................. AC 240 V/50 Hz

[China model] ...................................................... AC 220 V/50 Hz

[General model] ........................ AC 110/120/220/240 V, 50/60 Hz

• Power Consumption

[U.S.A. model] .................................................................... 390 W

[Canada model] ...................................................... 400 W/500 VA

[Other models] ..................................................................... 410 W

Standby Mode ......................................................... approx. 1.5 W

• AC Outlets

[U.S.A. and Canada models] .......................... 2 (80 W maximum)

[China and General models] ........................... 2 (50 W maximum)

[Australia model] .......................................... 1 (100 W maximum)

• Dimension (W x H x D)

............................ 435 x 171 x 432 mm (17-1/8” x 6-3/4” x 17”)

• Weight ......................................................................... 15 kg (33 lbs)

• Accessories ............................................................... Remote control

....................................................................................... Batteries

......................................................................... AM loop antenna

...................................................................... Indoor FM antenna

......................................................................... Connection guide

[U.S.A. and Canada models] ........................................ Power cord

*Specifications are subject to change without notice.

0112V2200_76-83_EN(U) 01.8.1, 9:44 AM83

OWNER’S MANUAL

RX-V2200

AV Receiver

IMPORTANT

Please record the serial number of this unit in the

space below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia

V795410

0100V2200(U)-cv1/4 01.8.1, 10:24 AM1

Yamaha RX-V2200 Manual de usuario

Marca: Yamaha

Modelo: RX-V2200

Categoría: Receptor

Tipo: Manual de usuario

Descargar PDF

informe

en otros idiomas

français: Yamaha RX-V2200 Manuel utilisateur
italiano: Yamaha RX-V2200 Manuale utente
English: Yamaha RX-V2200 User manual
Deutsch: Yamaha RX-V2200 Benutzerhandbuch
русский: Yamaha RX-V2200 Руководство пользователя
Nederlands: Yamaha RX-V2200 Handleiding
português: Yamaha RX-V2200 Manual do usuário
dansk: Yamaha RX-V2200 Brugermanual
polski: Yamaha RX-V2200 Instrukcja obsługi
čeština: Yamaha RX-V2200 Uživatelský manuál
svenska: Yamaha RX-V2200 Användarmanual
Türkçe: Yamaha RX-V2200 Kullanım kılavuzu
suomi: Yamaha RX-V2200 Ohjekirja
română: Yamaha RX-V2200 Manual de utilizare

Otros documentos

Insignia NS-H2001 Manual de usuario

Yamaha RX-V2200 Manual de usuario

Yamaha RX-V2200 Manual de usuario

en otros idiomas

Artículos relacionados

Otros documentos