Tripp Lite PS-5-INT Manual de usuario

Categoría
Protectores de sobretensión
Tipo
Manual de usuario

Este manual también es adecuado para

CAUTION!
DO NOT connect to an ungrounded outlet. DO NOT use
with extension cords or adapters that eliminate the
connection to ground. The power strip is designed for
indoor use only. Install the power strip away from heat
emitting appliances such as radiators or heat registers. Do not
install where excessive moisture or other conductive
contaminants are present. Never install electrical wiring
during a lightning storm.
Installation
1) Connect Your Power Strip to Your AC Power Line
MMooddeellss PPSS--661155--HHGG aanndd SSPPSS--661155--HHGG
:Plug the power cord into
a utility outlet.The power strip’s power cord should only be
connected to a standard 3-wire grounded 120V AC 60 Hz
outlet.
MMooddeell PPSS--55--IINNTT::
Plug a female IEC320 power cord (not
included) into both the power strip and a utility outlet.The
power cord should only be connected to a grounded 230V
AC, 50/60 Hz outlet.
2) Connect AC Equipment to Your Power Strip
Plug the AC power cords of your equipment into your power
strip. Do not use extension cords or adapters that eliminate
the connection to ground.
DO NOT OVERLOAD your power strip.The PS-615-HG and
the SPS-615-HG have a amp rating of 15 amps.The PS-5-INT
has a amp rating of 10 amps. Each outlet can handle a load
of up to the model’s amp rating, but do not exceed a
ttoottaall
load of more than the model’s amp rating for all outlets.
If the circuit breaker trips, outlets will cease to provide
power. Reduce the load on the power strip down to your
1111 W. 35
th
Street Chicago, IL 60609 • Customer Support: (773) 869-1234 • www.tripplite.com
PS Series
Power
Strips
unit’s amp rating by unplugging excess equipment, then
depress the circuit breaker button to reset.
Hospital Grade Plug & Outlets (HG models only)
The PS-615-HG and SPS-615-HG power strips feature hospital
grade plugs and outlets,and exhibit less than 100 microamps
of leakage to ground.
Surge Suppression (SPS model only)
The SPS-615-HG power strip is also a surge suppressor,
providing 300 joules of surge suppression that protect
connected devices from surges and spikes on the AC power
line.
Lifetime Limited Warranty
The seller warrants this product, if used in accordance with
all applicable instructions, to be free from original defects in
material and workmanship for its lifetime. If the product
should prove defective in material or workmanship within
that period, Seller will repair or replace the product, in its
sole discretion. Service under this Warranty can only be
obtained by your delivering or shipping the product (with
all shipping or delivery charges prepaid) to:Tripp Lite, 1111
W. 35th St., Chicago,IL 60609.Seller will pay return shipping
charges.The warranties of all TRIPP LITE surge suppressors
are null and void if they have been connected to the output
of any UPS system. The warranties of all TRIPP LITE UPS
Systems are null and void if a surge suppressor has been
connected to its output receptacles.THIS WARRANTY DOES
NOT APPLY TO NORMAL WEAR OR TO DAMAGE
RESULTING FROM ACCIDENT,MISUSE,ABUSE OR NEGLECT.
SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN
IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE
INSTRUCTIONS.
THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT
TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL
IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF
MERCHANTABILITY OR FITNESS, ARE LIMITED IN
DURATION TO THE WARRANTY PERIOD SET FORTH
ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL
INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some
states do not allow limitations on how long an implied
warranty lasts,and some states do not allow the exclusion or
limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you. This
Warranty gives you specific legal rights, and you may have
other rights which vary from jurisdiction to jurisdiction.)
To receive service under this warranty, you must be the
original purchaser/user of the product in question.You must
obtain a Returned Material Authorization (RMA) number
from TRIPP LITE. Products must be returned to TRIPP LITE
with transportation charges prepaid and must be
accompanied by a brief description of the problem and
proof of date and place of purchase.
TRIPP LITE; 1111 35th St.; Chicago, IL 60609
WWAARRNNIINNGG::
The individual user should take care to
determine prior to use whether this device is suitable,
adequate or safe for the use intended. Since individual
applications are subject to great variation, the manufacturer
makes no representation or warranty as to the suitability or
fitness of these devices for any specific application.
Policy of Tripp Lite is one of continuous improvement.
Specifications are subject to change without notice.
93-2004 (200108202)
PS Series
IMPORTANTES INSTRUCCIONES DE SEGURIDAD.
GUÁRDELAS.
Barras de
contactos
Contactos y enchufes de grado hospitalario
(únicamente los modelos HG)
Las barras de contactos PS-615-HG y SPS-615-HG tienen
contactos y enchufes de grado hospitalario y permiten fugas
menores a 100 microamperios hacia la conexión a tierra.
Eliminación de sobretensiones (únicamente
los modelos SPS)
La barra de contactos SPS-615-HG también es un supresor de
sobretensiones, proporcionando una supresión de
sobretensiones de 300 joules que protege los dispositivos
conectados de sobretensiones y variaciones repentinas en la
línea de suministro de corriente alterna.
Garantía limitada durante la vida útil del equipo
El distribuidor garantiza que este producto, si se utiliza de
acuerdo con las instrucciones aplicables, se encuentra libre
de defectos originales en sus materiales y mano de obra
durante toda su vida útil. Si dentro de este periodo se
demuestra que el producto tiene defectos en sus materiales
o mano de obra, el distribuidor reparará o cambiará el
producto, a su entera discreción. El servicio proporcionado
mediante esta garantía sólo podrá obtenerse si se devuelve o
envía el producto (con todos los gastos de flete y transporte
previamente pagados) a: Tripp Lite, 1111 W. 35th Street,
Chicago,IL 60609,EE.UU.El distribuidor pagará los gastos de
devolución. Las garantías de todos los supresores de
sobretensiones de Tripp Lite se anularán y no serán válidas si
se han conectado en los contactos de cualquier sistema UPS
(no-break). Las garantías de todos los sistemas UPS de Tripp
Lite serán anuladas o no serán válidas si se conecta un
supresor de sobretensiones a sus contactos. ESTA
GARANTÍA NO SE APLICA AL DESGASTE NORMAL NI A LOS
DAÑOS QUE SEAN RESULTADO DE ACCIDENTES,MAL USO,
ABUSO O NEGLIGENCIA. LOS DISTRIBUIDORES NO
OFRECEN NINGUNA OTRA GARANTÍA A LA
EXPRESAMENTE ESTABLECIDA EN EL PRESENTE
DOCUMENTO. CON EXCEPCIÓN DE LO EXPRESAMENTE
PROHIBIDO POR LA LEY APLICABLE, TODAS LAS
GARANTÍAS IMPLÍCITAS, INCLUYENDO LAS GARANTÍAS
¡PRECAUCIÓN!
NUNCA conecte el equipo a una toma de corriente sin
conexión a tierra. NO LO UTILICE con extensiones o
adaptadores que eliminen la conexión a tierra. La barra de
contactos está diseñada exclusivamente para uso en
interiores. Instale la barra de contactos lejos de dispositivos
que emitan calor,como radiadores o registros de calefacción.
No lo instale en lugares donde exista exceso de humedad o
haya posibilidad de interferencias eléctricas.Nunca instale el
cableado durante una tormenta.
Instalación
1) Conecte el cable de contactos a la línea de
suministro de corriente alterna
Modelos PS-615-HG y SPS-615-HG: Enchufe el cable de
corriente en una toma de energía eléctrica. El cable de
corriente de la barra de contactos debe conectarse a una
toma estándar de 3 hilos,conectada a tierra, de 120 VCA y 60
Hz.
MMooddeelloo PPSS--55--IINNTT::
Enchufe un cable de corriente hembra
IEC320 (no incluido) tanto en la barra de contactos como en
la toma de electricidad. El cable de corriente sólo debe
conectarse a una toma de energía de CA con conexión
adecuada a tierra, de 230 V, 50 / 60 Hz.
2) Conecte el equipo eléctrico a la barra de
contactos
Enchufe los cables de corriente CA de su equipo a la barra de
contactos. No utilice extensiones o adaptadores que eliminen
la conexión a tierra.
NUNCA SOBRECARGUE la barra de contactos. Los modelos
PS-615-HG y SPS-615-HG tienen una carga nominal de 15
amperios. El modelo PS-5-INT tiene una carga nominal de 10
amperios. Cada contacto soporta una carga de acuerdo a la
corriente nominal del modelo; sin embargo, nunca exceda la
carga
ttoottaall
por encima del valor de la corriente nominal de su
modelo para todos los contactos.
Si se activa el "breaker", los contactos dejarán de suministrar
corriente. Reduzca la carga en la barra de contactos según el
amperaje indicado para la unidad,desenchufando el exceso de
equipo,y después oprima el botón del "breaker" para reiniciar
el sistema.
COMERCIALES O DE ADECUACIÓN, ESTÁN LIMITADAS EN
SU VIGENCIA AL PERIODO DE GARANTÍA ESTABLECIDO
ANTERIORMENTE; ADEMÁS, ESTA GARANTÍA EXCLUYE
EXPRESAMENTE TODO DAÑO INCIDENTAL Y
CONSECUENCIAL (algunos estados no permiten la
limitación de la vigencia de la garantía implícita; además,
algunos estados no permiten la exclusión o limitación de los
daños incidentales o consecuenciales, por lo que las
limitaciones o exclusiones señaladas anteriormente no se
aplicarán en tales casos.Esta garantía otorga derechos legales
específicos, aunque se pueden tener además otros derechos
que variarán de una jurisdicción a otra).
Para recibir el servicio establecido por esta garantía, se debe
ser el usuario o comprador original del producto en
cuestión. Deberá obtener de TRIPP LITE un número de
autorización de devolución de material (RMA). Los
productos deberán devolverse a TRIPP LITE con los cargos
de transporte previamente pagados y acompañados de una
descripción breve del problema encontrado,así como de los
documentos probatorios de la fecha y lugar de compra.
TRIPP LITE; 1111 35th St.; Chicago, IL 60609; EE.UU.
ADVERTENCIA: El usuario deberá tener el cuidado de
determinar si el dispositivo es apropiado, adecuado o seguro
para el uso al que lo tiene destinado,antes de utilizarlo.Dado
que las diferentes aplicaciones están sujetas a una enorme
variación, el fabricante no puede garantizar que el equipo se
adapte o sea apropiado para cualquier aplicación.
La política de Tripp Lite es de mejora continua. Las
especificaciones están sujetas a cambios sin previo aviso.
1111 W. 35
th
Street Chicago, IL 60609 EE.UU.• Atención al cliente: +1 (773) 869-1234 • www.tripplite.com

Transcripción de documentos

PS Series ™ Power Strips IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. 1111 W. 35th Street Chicago, IL 60609 • Customer Support: (773) 869-1234 • www.tripplite.com CAUTION! DO NOT connect to an ungrounded outlet. DO NOT use with extension cords or adapters that eliminate the connection to ground. The power strip is designed for indoor use only. Install the power strip away from heat emitting appliances such as radiators or heat registers. Do not install where excessive moisture or other conductive contaminants are present. Never install electrical wiring during a lightning storm. Installation 1) Connect Your Power Strip to Your AC Power Line Models PS-615-HG and SPS-615-HG: Plug the power cord into a utility outlet.The power strip’s power cord should only be connected to a standard 3-wire grounded 120V AC 60 Hz outlet. Model PS-5-INT: Plug a female IEC320 power cord (not included) into both the power strip and a utility outlet.The power cord should only be connected to a grounded 230V AC, 50/60 Hz outlet. 2) Connect AC Equipment to Your Power Strip Plug the AC power cords of your equipment into your power strip. Do not use extension cords or adapters that eliminate the connection to ground. DO NOT OVERLOAD your power strip. The PS-615-HG and the SPS-615-HG have a amp rating of 15 amps.The PS-5-INT has a amp rating of 10 amps. Each outlet can handle a load of up to the model’s amp rating, but do not exceed a total load of more than the model’s amp rating for all outlets. If the circuit breaker trips, outlets will cease to provide power. Reduce the load on the power strip down to your unit’s amp rating by unplugging excess equipment, then depress the circuit breaker button to reset. Hospital Grade Plug & Outlets (HG models only) The PS-615-HG and SPS-615-HG power strips feature hospital grade plugs and outlets, and exhibit less than 100 microamps of leakage to ground. Surge Suppression (SPS model only) The SPS-615-HG power strip is also a surge suppressor, providing 300 joules of surge suppression that protect connected devices from surges and spikes on the AC power line. Lifetime Limited Warranty The seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for its lifetime. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole discretion. Service under this Warranty can only be obtained by your delivering or shipping the product (with all shipping or delivery charges prepaid) to:Tripp Lite, 1111 W. 35th St., Chicago, IL 60609. Seller will pay return shipping charges.The warranties of all TRIPP LITE surge suppressors are null and void if they have been connected to the output of any UPS system. The warranties of all TRIPP LITE UPS Systems are null and void if a surge suppressor has been connected to its output receptacles.THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE,ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN PS Series ™ Barras de contactos THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which vary from jurisdiction to jurisdiction.) To receive service under this warranty, you must be the original purchaser/user of the product in question.You must obtain a Returned Material Authorization (RMA) number from TRIPP LITE. Products must be returned to TRIPP LITE with transportation charges prepaid and must be accompanied by a brief description of the problem and proof of date and place of purchase. TRIPP LITE; 1111 35th St.; Chicago, IL 60609 WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application. Policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice. IMPORTANTES INSTRUCCIONES DE SEGURIDAD. GUÁRDELAS. 1111 W. 35th Street Chicago, IL 60609 EE.UU.• Atención al cliente: +1 (773) 869-1234 • www.tripplite.com ¡PRECAUCIÓN! NUNCA conecte el equipo a una toma de corriente sin conexión a tierra. NO LO UTILICE con extensiones o adaptadores que eliminen la conexión a tierra. La barra de contactos está diseñada exclusivamente para uso en interiores. Instale la barra de contactos lejos de dispositivos que emitan calor, como radiadores o registros de calefacción. No lo instale en lugares donde exista exceso de humedad o haya posibilidad de interferencias eléctricas. Nunca instale el cableado durante una tormenta. Instalación 1) Conecte el cable de contactos a la línea de suministro de corriente alterna Modelos PS-615-HG y SPS-615-HG: Enchufe el cable de corriente en una toma de energía eléctrica. El cable de corriente de la barra de contactos debe conectarse a una toma estándar de 3 hilos, conectada a tierra, de 120 VCA y 60 Hz. Modelo PS-5-INT: Enchufe un cable de corriente hembra IEC320 (no incluido) tanto en la barra de contactos como en la toma de electricidad. El cable de corriente sólo debe conectarse a una toma de energía de CA con conexión adecuada a tierra, de 230 V, 50 / 60 Hz. 2) Conecte el equipo eléctrico a la barra de contactos Enchufe los cables de corriente CA de su equipo a la barra de contactos. No utilice extensiones o adaptadores que eliminen la conexión a tierra. NUNCA SOBRECARGUE la barra de contactos. Los modelos PS-615-HG y SPS-615-HG tienen una carga nominal de 15 amperios. El modelo PS-5-INT tiene una carga nominal de 10 amperios. Cada contacto soporta una carga de acuerdo a la corriente nominal del modelo; sin embargo, nunca exceda la carga total por encima del valor de la corriente nominal de su modelo para todos los contactos. Si se activa el "breaker", los contactos dejarán de suministrar corriente. Reduzca la carga en la barra de contactos según el amperaje indicado para la unidad,desenchufando el exceso de equipo, y después oprima el botón del "breaker" para reiniciar el sistema. Contactos y enchufes de grado hospitalario (únicamente los modelos HG) Las barras de contactos PS-615-HG y SPS-615-HG tienen contactos y enchufes de grado hospitalario y permiten fugas menores a 100 microamperios hacia la conexión a tierra. Eliminación de sobretensiones (únicamente los modelos SPS) La barra de contactos SPS-615-HG también es un supresor de sobretensiones, proporcionando una supresión de sobretensiones de 300 joules que protege los dispositivos conectados de sobretensiones y variaciones repentinas en la línea de suministro de corriente alterna. Garantía limitada durante la vida útil del equipo El distribuidor garantiza que este producto, si se utiliza de acuerdo con las instrucciones aplicables, se encuentra libre de defectos originales en sus materiales y mano de obra durante toda su vida útil. Si dentro de este periodo se demuestra que el producto tiene defectos en sus materiales o mano de obra, el distribuidor reparará o cambiará el producto, a su entera discreción. El servicio proporcionado mediante esta garantía sólo podrá obtenerse si se devuelve o envía el producto (con todos los gastos de flete y transporte previamente pagados) a: Tripp Lite, 1111 W. 35th Street, Chicago, IL 60609, EE.UU. El distribuidor pagará los gastos de devolución. Las garantías de todos los supresores de sobretensiones de Tripp Lite se anularán y no serán válidas si se han conectado en los contactos de cualquier sistema UPS (no-break). Las garantías de todos los sistemas UPS de Tripp Lite serán anuladas o no serán válidas si se conecta un supresor de sobretensiones a sus contactos. ESTA GARANTÍA NO SE APLICA AL DESGASTE NORMAL NI A LOS DAÑOS QUE SEAN RESULTADO DE ACCIDENTES, MAL USO, ABUSO O NEGLIGENCIA. LOS DISTRIBUIDORES NO OFRECEN NINGUNA OTRA GARANTÍA A LA EXPRESAMENTE ESTABLECIDA EN EL PRESENTE DOCUMENTO. CON EXCEPCIÓN DE LO EXPRESAMENTE PROHIBIDO POR LA LEY APLICABLE, TODAS LAS GARANTÍAS IMPLÍCITAS, INCLUYENDO LAS GARANTÍAS COMERCIALES O DE ADECUACIÓN, ESTÁN LIMITADAS EN SU VIGENCIA AL PERIODO DE GARANTÍA ESTABLECIDO ANTERIORMENTE; ADEMÁS, ESTA GARANTÍA EXCLUYE EXPRESAMENTE TODO DAÑO INCIDENTAL Y CONSECUENCIAL (algunos estados no permiten la limitación de la vigencia de la garantía implícita; además, algunos estados no permiten la exclusión o limitación de los daños incidentales o consecuenciales, por lo que las limitaciones o exclusiones señaladas anteriormente no se aplicarán en tales casos. Esta garantía otorga derechos legales específicos, aunque se pueden tener además otros derechos que variarán de una jurisdicción a otra). Para recibir el servicio establecido por esta garantía, se debe ser el usuario o comprador original del producto en cuestión. Deberá obtener de TRIPP LITE un número de autorización de devolución de material (RMA). Los productos deberán devolverse a TRIPP LITE con los cargos de transporte previamente pagados y acompañados de una descripción breve del problema encontrado, así como de los documentos probatorios de la fecha y lugar de compra. TRIPP LITE; 1111 35th St.; Chicago, IL 60609; EE.UU. ADVERTENCIA: El usuario deberá tener el cuidado de determinar si el dispositivo es apropiado, adecuado o seguro para el uso al que lo tiene destinado, antes de utilizarlo. Dado que las diferentes aplicaciones están sujetas a una enorme variación, el fabricante no puede garantizar que el equipo se adapte o sea apropiado para cualquier aplicación. La política de Tripp Lite es de mejora continua. Las especificaciones están sujetas a cambios sin previo aviso. 93-2004 (200108202)
1 / 1

Tripp Lite PS-5-INT Manual de usuario

Categoría
Protectores de sobretensión
Tipo
Manual de usuario
Este manual también es adecuado para