GE JVW5301 El manual del propietario

Categoría
Campanas de cocina
Tipo
El manual del propietario
Write the model and serial
numbers here:
Model # _________________
Serial # _________________
You can find them on a label
on the inside of the hood.
ESPAÑOL
Para consultar una version en
español de este manual de
instrucciones, visite nuestro sitio de
internet GEAppliances.com.
WALL CHIMNEY
VENT HOODS
49-80760-2 09-17 GEA
GE is a trademark of the General Electric Company. Manufactured under trademark license.
SAFETY INFORMATION .............3
USING THE HOOD
Controls ..................................5
Filter .................................... 6
CARE AND CLEANING
Surfaces ..................................8
Lights ....................................8
TROUBLESHOOTING TIPS ..........10
WARRANTY ..........................14
ACCESSORIES .......................15
CONSUMER SUPPORT ..............16
OWNER’S MANUAL
JVW5301 (30" Pyramid)
JVW5361 (36" Pyramid)
PVW7301 (30" Glass)
PVW7361 (36" Glass)
2 49-80760-2
THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.
We take pride in the craftsmanship, innovation and design that goes into every GE Appliances
product, and we think you will too. Among other things, registration of your appliance ensures that we
can deliver important product information and warranty details when you need them.
Register your GE appliance now online. Helpful websites and phone numbers are available in the
Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration
card included in the packing material.
49-80760-2 3
SAFETY INFORMATION
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
B. Before servicing or cleaning unit, switch power off
at service panel and lock the service disconnecting
means to prevent power from being switched
on accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the
service panel.
C. Do not use this unit with any solid-state speed
control device.
D. This unit must be grounded.
CAUTION
FOR GENERAL VENTILATING USE
ONLY. DO NOT USE TO EXHAUST HAZARDOUS
OR EXPLOSIVE MATERIALS AND VAPORS.
CAUTION
TO REDUCE RISK OF FIRE AND
TO PROPERLY EXHAUST AIR, BE SURE TO DUCT
AIR OUTSIDE. DO NOT VENT EXHAUST AIR INTO
SPACES WITHIN WALLS OR CEILINGS OR INTO
ATTICS, CRAWL SPACES OR GARAGES.
WARNING
TO REDUCE THE RISK OF INJURY
TO PERSONS IN THE EVENT OF A RANGE TOP
GREASE FIRE, OBSERVE THE FOLLOWING*:
A. SMOTHER FLAMES with a close-fitting lid, cookie
sheet or metal tray, then turn off the burner. BE
CAREFUL TO PREVENT BURNS. If the flames do
not go out immediately, EVACUATE AND CALL
THE FIRE DEPARTMENT.
B. NEVER PICK UP A FLAMING PAN—You may be
burned.
C. DO NOT USE WATER, including wet dishcloths or
towels—a violent steam explosion will result.
D. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher,
and you already know how to operate it.
2. The fire is small and contained in the area where
it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety” published by NFPA.
4 49-80760-2
SAFETY INFORMATION
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF A
RANGE TOP GREASE FIRE:
A. Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on
medium settings.
B. Always turn hood ON when cooking at high heat or
when flambéing food (i.e. Crepes Suzette, Cherries
Jubilee, Peppercorn Beef Flambé).
C. Clean ventilating fans frequently. Grease should not
be allowed to accumulate on fan or filter.
D. Use proper pan size. Always use cookware
appropriate for the size of the surface element.
WARNING
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Installation work and electrical wiring must be
done by qualified person(s) in accordance with all
applicable codes and standards, including fire-rated
construction.
B. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), the American Society for
Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE) and the local code authorities.
C. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
D. Ducted fans must always be vented to the outdoors.
E. When applicable, install any makeup (replacement)
air system in accordance with local building
code requirements. Visit GEAppliances.com for
available makeup air solutions.
F. Turn off breaker to adjacent rooms while working.
WARNING
TO REDUCE THE RISK OF FIRE,
USE ONLY METAL DUCTWORK.
Ŷ'RQRWDWWHPSWWRUHSDLURUUHSODFHDQ\SDUWRI\RXU
hood unless it is specifically recommended in this
manual. All other servicing should be referred to a
qualified technician.
How to Remove Protective Shipping Film and Packaging Tape
Carefully grasp a corner of the protective shipping film
with your fingers and slowly peel it from the appliance
surface. Do not use any sharp items to remove the film.
Remove all of the film before using the appliance for the
first time.
To assure no damage is done to the finish of the
product, the safest way to remove the adhesive from
packaging tape on new appliances is an application of
a household liquid dishwashing detergent. Apply with a
soft cloth and allow to soak. NOTE: If surface is still not
clean, see page 8 for more cleaning options.
NOTE: The adhesive must be removed from all parts.
49-80760-2 5
1. Rangehood Control Panel:
The control panel
is located on the front of the canopy. The position
and function of each control button are noted below.
2.
Light Button: On/Night/Off switch for the halogen
lights. Press the LIGHT button to turn the lights on,
again to set the lights to night setting, and again to
turn off.
3. Fan Off Button: Off switch for the fan. The fan
can be operated by pressing any of the fan setting
buttons. Hold for 2 seconds to activate auto off after
15 minutes.
4. Fan Settings Buttons: Speed control for
fan. Press the switch Lo for LOW speed, Med for
MEDIUM speed and Hi for HIGH speed. Hold down
the Hi button for 2 seconds to activate the BOOST
SPEED that will run for 10 minutes.
Controls
USING THE HOOD: Controls
41
23
6 49-80760-2
Filters (Pyramid Models JVW5301, JVW5361)
USING THE HOOD: Filters
Be sure the circuit breaker is off and all surfaces are cool before cleaning or servicing any part of the vent hood.
Metal Grease Filter
The metal filters trap grease during cooking.
The filters must ALWAYS be in place when the hood
is in use. The grease filters are dishwasher-safe and
should be cleaned every 6 months, or as needed.
To remove:
Pull downward on the filter lock to release the filter.
To replace:
Fit the tabs at the bottom of the filter into the slots in the
back of the filter opening. Lift up the front side of the filter
and push gently until the filter locks into place. Make sure
the filter lock is in the closed position to secure the filter.
To clean, swish the filter in hot soapy water and rinse
in clean water or wash it in the dishwasher. Do not use
abrasive cleansers.
NOTE: Some discoloration may occur in the dishwasher.
For Recirculation Installation Only
Charcoal Filter (Not Included)
If the model is not vented to the outside, the air needs to
be recirculated through a disposable charcoal filter that
helps remove smoke and odors.
NOTE: DO NOT rinse, or put charcoal filter in an
automatic dishwasher.
The charcoal filter cannot be cleaned. It must be
replaced. It is recommended that the charcoal filter
be replaced every 6-12 months or if it is noticeably
dirty or discolored.
Order Charcoal Filter JXCF72
To inquire about purchasing replacement charcoal filters
or to find the location of a dealer nearest you, please call
our toll-free number:
National Parts Center 800.626.2002
To install:
1. Remove the metal filters—see Metal grease filter
section.
2. Place the side of the charcoal filter with the tabs
against the side of the blower.
3. Align the double lines on the charcoal filter with the
"unlocked" symbol on the blower.
4. Push and twist the charcoal filter downward until the
double lines align with the "locked" symbol on the
blower.
5. Repeat with second filter on the other side of the
blower.
6. Replace the metal filters—see Metal grease filter
section.
To remove:
1. Remove the metal filters—see Metal grease filter
section.
2. Twist the charcoal filters upward on both sides of the
motor to align the double lines with the "unlocked"
symbol. The locks are now disengaged and the
charcoal filters can be removed.
To remove:
1. Remove the metal filters—see Metal grease filter
section.
2. Unclip the charcoal filter by pressing the release clip.
3. Carefully remove charcoal filter from tab.
NOTE: The 30"
models have 2 grease
filters. The 36" models
have 3 grease filters.
49-80760-2 7
Be sure the circuit breaker is off and all surfaces are cool before cleaning or servicing any part of the vent hood.
Metal Grease Filter
The metal filter traps grease released by foods from
cooking.
The filters must ALWAYS be in place when the hood
is in use. The grease filters are dishwasher-safe and
should be cleaned every 6 months, or as needed.
To remove:
Pull downward on the filter lock to release the filter.
To replace:
Fit the tabs at the bottom of the filter behind the ledge of
the filter opening. Lift up the front side of the filter, push
downward on the filter lock, and push gently until the filter
is in place. Release the filter lock to secure the filter in
place.
To clean, swish the filter in hot soapy water and rinse
in clean water or wash it in the dishwasher. Do not use
abrasive cleansers.
NOTE: Some discoloration may occur in the dishwasher.
For Recirculation Installation Only
Charcoal Filter (Not Included)
If the model is not vented to the outside, the air needs to
be recirculated through a disposable charcoal filter that
helps remove smoke and odors.
NOTE: DO NOT rinse, or put charcoal filter in an
automatic dishwasher.
The charcoal filter cannot be cleaned. It must be
replaced. It is recommended that the charcoal filter
be replaced every 6-12 months or if it is noticeably
dirty or discolored.
Order Charcoal Filter JXCF71
To inquire about purchasing replacement charcoal filters
or to find the location of a dealer nearest you, please call
our toll-free number:
National Parts Center 800.626.2002
To install:
1. Insert the bottom tabs of the charcoal filter into the two
slots at the back of the unit. Pivot filter upward into
place while depressing the locking tabs.
2. Replace the metal filter—see Metal grease filter
section.
To remove:
1. Remove the metal filter—see Metal grease filter
section.
2. Press on the two tabs on the charcoal filter to
disengage the lock and pivot to remove.
Filters (Glass Models PVW7301, PVW7361)
CARE AND CLEANING: Filters
Filter Lock
8 49-80760-2
Lights (Pyramid Models JVW5301, JVW5361)
Stainless Steel Surfaces (on some models)
Do not use a steel wool pad; it will scratch the surface.
To clean the stainless steel surface, use warm sudsy
water or a stainless steel cleaner or polish. Always wipe
the surface in the direction of the brush line. Follow
the cleaner instructions for cleaning the stainless steel
surface. Cleaners with oxalic acid such as Bar Keepers
Friend Soft Cleanser™ will remove surface rust,
tarnish, and small blemishes. Use only a liquid cleanser
free of grit and rub in the direction of the brush lines with
a damp soft sponge.
To inquire about purchasing stainless steel appliance
cleaner or polish, or to find the location of a dealer
nearest you, please call our toll-free number:
National Parts Center
800.626.2002
GEApplianceParts.com
Painted Surfaces (on some models)
Do not use a steel wool pads or other abrasive
cleaners; they will scratch the surface.
Clean grease-laden surfaces of the hood frequently. To
clean the hood surface, use a hot, damp cloth with a
mild detergent suitable for painted surfaces. About one
tablespoon of ammonia may be added to the water. Use
a clean, hot, damp cloth to remove soap. Dry with a dry,
clean cloth.
NOTE: When cleaning, take care not to come in contact
with filters and other surfaces.
CAUTION
When cleaning the hood surfaces,
be certain that you do not touch the light with moist
hands or cloth. A warm or hot light may break if
touched with a moist surface. Always let the light
cool completely before cleaning around it.
CAUTION
Allow lights to cool before touching.
To change the lights:
1. Before attempting to replace the lights, make sure that
the light switch is turned off.
2. Using a flathead screwdriver, unclip the wire lighting
support and gently pull the support down from the
hood.
3. While holding the socket, twist the light counter-
clockwise to remove. Replace it with a new GU-10
light. Make sure the new light is locked in the socket.
4. Replace the new light and socket into the hood and
engage into the light support.
Surfaces
CARE AND CLEANING: Surfaces / Lights
49-80760-2 9
CAUTION
Allow lights to cool before touching.
To change the lights:
1. Before attempting to replace the lights, make sure that
the light switch is turned off.
2. Wear gloves. Do not touch the light with your bare
fingers. Skin oils can cause early light failure. Wear
clean gloves or use a paper towel to handle the light.
3. Using a flathead screwdriver, unclip the metal trim ring
from the lighting support.
4. Remove the light by pulling towards the front of the
hood. Replace it with a new G4 20W Clear Halogen
Capsule light by inserting the two stakes into the holes
and pushing towards the back of the hood to secure
the light.
5. Reinsert the metal trim ring by lining up the two side
holes on the lighting support with the two tabs on the
trim ring, and push upward.
Lights (Glass Models PVW7301, PVW7361)
CARE AND CLEANING: Lights
10 49-80760-2
Troubleshooting Tips ... Before you call for service
Save time and money! Review the charts on the following pages first and you may not need to call for service.
Problem Possible Cause What To Do
Fan/Light does not
operate when either
button is pressed
A house fuse may be blown or a circuit
breaker tripped.
Replace fuse or reset circuit breaker.
Fan does not operate
when fan Lo, Med,
Hight buttons are
pressed
The blower connector is loose or not
plugged into its mating connector.
Disconnect power to the unit. Remove the filters
and look up at the blower. If the blower connector
plug is loose or you see the connector dangling,
the installer failed to plug it in securely. See the
mini manual for the plug location and how to plug
in the connector.
Loud or abnormal
airflow noise
Wrong duct size used in installation. This hood requires 6” ducting to perform optimally.
Using smaller duct pipe will cause reduced
venting.Minimize the duct run length and number
of transitions and elbows. GE service technicians
cannot correct this issue if installed improperly.
Fan fails to circulate
air or moves air slower
than normal and/or
fan is making loud or
abnormal airflow noise
Obstructions in duct work. Make sure nothing is blocking the vent. Make sure
your wall or roof cap has a blade or door.
Damper blade on wall or roof cap may
not be open.
Make sure damper swings freely. Damper blades
may flip over and will not fully open when this
happens. Adjust to original position.
Metal grease filter and charcoal filter (if
present) may be dirty.
Clean the metal grease filter and replace charcoal
filter (if present). See Care and Cleaning of the
Vent Hood.
Insufficient makeup (replacement) air Sufficient makeup (replacement) air is required
for exhausting appliances to operate to rating.
Check with local building codes, which may
require or strongly advise the use of makeup air.
Visit GEAppliances.com for available makeup air
solutions.
The hood controls are
not operating correctly
Control logic confused. Disconnect power to the hood by resetting the
circuit breaker. Wait 30 seconds to allow controls
to reset.
Early light failure Replacing lights with bare hands. Replace lights while wearing gloves to keep skin
oils off lights.
Light wattage is too high. Replace with correct wattage.
TROUBLESHOOTING TIPS
49-80760-2 11
Notes
12 49-80760-2
Notes
49-80760-2 13
Notes
14 49-80760-2
Staple your receipt here. Proof of the original purchase
date is needed to obtain service under the warranty.
GEAppliances.com
All warranty service is provided by our Factory Service Centers, or an authorized Customer Care
®
technician. To schedule
service online, visit us at www.geappliances.com/service_and_support/, or call GE Appliances at 800.GE.CARES
(800.432.2737). Please have your serial number and your model number available when calling for service.
Servicing your appliance may require the use of the onboard data port for diagnostics. This gives a GE Appliances factory
service technician the ability to quickly diagnose any issues with your appliance and helps GE Appliances improve its
products by providing GE Appliances with information on your appliance. If you do not want your appliance data to be
sent to GE Appliances, please advise your technician not to submit the data to GE Appliances at the time of service.
What GE Appliances will not cover:
Ŷ Service trips to your home to teach you how to use
the product.
Ŷ Improper installation, delivery, or maintenance.
Ŷ Failure of the product if it is abused, misused,
modified, or used for other than the intended purpose
or used commercially.
Ŷ Replacement of house fuses or resetting of circuit
breakers.
Ŷ Damage to the product caused by accident, fire,
floods, or acts of God.
Ŷ Damage to finish, such as surface rust, tarnish, or small
blemishes not reported within 48 hours of delivery.
Ŷ Incidental or consequential damage caused by
possible defects with this appliance.
Ŷ Damage caused after delivery.
Ŷ Product not accessible to provide required service.
Ŷ Service to repair or replace light bulbs, except for LED
lamps.
WARRANTY
GE Appliances Vented Range Hood Warranty
EXCLUSION OF IMPLIED WARRANTIES
Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties,
including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or
the shortest period allowed by law.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use
within the USA. If the product is located in an area where service by a GE Appliances Authorized Servicer is not available,
you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Appliances
Service location for service. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you
specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights
are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: GE Appliances, a Haier company
Extended Warranties: Purchase a GE Appliances extended warranty and learn about special discounts that are
available while your warranty is still in effect. You can purchase it online anytime at
www.geappliances.com/service_and_support/shop-for-extended-service-plans.htm
or call 800.626.2224 during normal business hours. GE Appliances Service will still be there after your warranty expires.
For the period of GE Appliances will replace
One year
From the date
of the original
purchase
Any part of the cooking product which fails due to a defect in materials or workmanship.
During this limited one-year warranty, GE Appliances will provide, free of charge, all labor
and related service costs to replace the defective part.
49-80760-2 15
ACCESSORIES
Looking For Something More?
GE Appliances offers a variety of accessories to
improve your cooking and maintenance experiences!
Refer to the Consumer Support page for phone numbers
and website information.
The following products and more are available:
Accessories
Parts
Charcoal Filter
High Ceiling Duct Cover Kit
Remote Control
Replacement Lights
Cleaning Supplies
CitruShine™ Stainless Steel Wipes
CERAMA BRYTE
®
Stainless Steel Appliance Cleaner
Bar Keepers Friend Soft Cleanser™
16 49-80760-2
Consumer Support
CONSUMER SUPPORT
GE Appliances Website
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day
of the year! You can also shop for more great GE Appliances products and take advantage of all our on-line support
services designed for your convenience. In the US: GEAppliances.com
Register Your Appliance
Register your new appliance on-line at your convenience! Timely product registration will allow for enhanced
communication and prompt service under the terms of your warranty, should the need arise. You may also mail in
the pre-printed registration card included in the packing material. In the US: GEAppliances.com/register
Schedule Service
Expert GE Appliances repair service is only one step away from your door. Get on-line and schedule your service at
your convenience any day of the year. In the US: GEAppliances.com/ge/service-and-support/service.htm
or call 800.432.2737 during normal business hours.
Extended Warranties
Purchase a GE Appliances extended warranty and learn about special discounts that are available while your
warranty is still in effect. You can purchase it on-line anytime. GE Appliances Services will still be there after your
warranty expires. In the US: GEAppliances.com/ge/service-and-support/shop-for-extended-service-plans.htm
or call 800.626.2224 during normal business hours.
Remote Connectivity
For assistance with wireless network connectivity (for models with remote enable),
visit our website at GEAppliances.com/ge/connected-appliances/ or call 800.220.6899 in the US.
Parts and Accessories
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes
(VISA, MasterCard and Discover cards are accepted). Order on-line today 24 hours every day.
In the US: GEApplianceparts.com or by phone at 877.959.8688 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing
generally should be referred to qualified service personnel. Caution must be exercised, since improper
servicing may cause unsafe operation.
Contact Us
If you are not satisfied with the service you receive from GE Appliances, contact us on our Website with all the
details including your phone number, or write to:
In the US: General Manager, Customer Relations | GE Appliances, Appliance Park | Louisville, KY 40225
GEAppliances.com/ge/service-and-support/contact.htm
Printed in Mexico
49-80760-2 09-17 GEA
INFORMACIÓN DE SEGURIDAD ....3
USO DE LA CAMPANA
Controles .................................5
Filtros ....................................6
CUIDADO Y LIMPIEZA
Superficies ................................8
Luces ....................................8
GARANTÍA ...........................14
ACCESORIOS ........................15
SOPORTE PARA
EL CONSUMIDOR ..................16
Escriba los números de modelo y
de serie aquí:
Nº de Modelo ____________
Nº de Serie ______________
Los puede encontrar en una etiqueta
en la pared interna de la campana.
GE es una marca registrada de General Electric Company. Fabricado bajo licencia de marca.
MANUAL DEL
PROPIETARIO
JVW5301 (30" Pirámide)
JVW5361 (36" Pirámide)
PVW7301 (30" Vidrio)
PVW7361 (36" Vidrio)
CAMPANAS DE VENTILACIÓN
PARA CHIMENEAS DE PARED
2 49-80760-2
GRACIAS POR HACER QUE GE APPLIANCES SEA PARTE DE SU HOGAR.
Ya sea que haya crecido usando GE Appliances, o que ésta es su primera vez, nos complace
tenerlo en la familia.
Sentimos orgullo por el nivel de arte, innovación y diseño de cada uno de los electrodomésticos de
GE Appliances, y creemos que usted también. Entre otras cosas, el registro de su electrodoméstico
asegura que podamos entregarle información importante del producto y detalles de la garantía
cuando los necesite.
Registre su electrodoméstico GE ahora a través de Internet. Sitios Web y números telefónicos útiles
están disponibles en la sección de Soporte para el Consumidor de este Manual del Propietario.
También puede enviar una carta en la tarjeta de inscripción preimpresa que se incluye con
el material embalado.
49-80760-2 3
INFORMACIÓN DE SEGURIDAD
INFORMACIÓN IMPORTANTE DE SEGURIDAD
LEA TODAS LAS INSTRUCCIONES ANTES DE USAR
LEA Y GUARDE ESTAS INSTRUCCIONES
ADVERTENCIA
PARA REDUCIR EL RIESGO
DE INCENDIO, DESCARGA ELÉCTRICA O LESIONES A
PERSONAS, CUMPLA CON LOS SIGUIENTES PUNTOS:
A. Utilice esta unidad sólo de la manera concebida por el
fabricante. Si tiene alguna pregunta, comuníquese con el
fabricante.
B. Antes de realizar reparaciones o limpiar la unidad,
desconecte la energía del panel de servicio y bloquee los
medios de desconexión para evitar el accionamiento de
la energía de manera accidental. Cuando los medios de
desconexión de servicio no pueden bloquearse, coloque
sobre el panel de servicio un dispositivo de advertencia
bien visible, como una etiqueta.
C. No utilice esta unidad con ningún dispositivo de control
de velocidad de estado sólido.
D. Esta unidad debe estar conectada a tierra.
PRECAUCIÓN
SÓLO PARA USO DE
VENTILACIÓN GENERAL. NO LO UTILICE PARA
ELIMINAR MATERIALES Y VAPORES PELIGROSOS O
EXPLOSIVOS.
PRECAUCIÓN
PARA REDUCIR EL RIESGO
DE INCENDIO Y PARA ELIMINAR EL AIRE DE ESCAPE
CORRECTAMENTE, ASEGÚRESE DE DIRIGIR EL AIRE
DEL CONDUCTO HACIA EL EXTERIOR. NO VENTILE EL
AIRE DE ESCAPE EN ESPACIOS DENTRO DE PAREDES
O CIELORRASOS O EN ÁTICOS, HUECOS SANITARIOS
O GARAJES.
ADVERTENCIA
PARA REDUCIR EL RIESGO DE
LESIONES A PERSONAS EN CASO DE UN INCENDIO
DE GRASA SOBRE UNA ESTUFA, CUMPLA CON LOS
SIGUIENTES PUNTOS*:
A. APAGUE LAS LLAMAS con una tapa que ajuste bien,
una plancha para galletas o una bandeja de metal, y
luego apague el quemador. TENGA MUCHO CUIDADO
A FIN DE EVITAR QUEMADURAS. Si las llamas no
se apagan de inmediato, SALGA DE LA VIVIENDA Y
LLAME AL DEPARTAMENTO DE BOMBEROS.
B. NUNCA LEVANTE UNA SARTÉN EN LLAMAS—
Usted puede quemarse.
C. NO UTILICE AGUA, incluyendo repasadores o toallas
húmedos—se provocará una violenta explosión de vapor.
D. Utilice un extintor SÓLO si:
1. Usted sabe que cuenta con un extintor Clase ABC y
ya sabe cómo utilizarlo.
2. El incendio es pequeño y se contuvo en el área donde
comenzó.
3. Se está llamando al departamento de bomberos.
4. Usted puede combatir el incendio con su espalda
dirigida hacia una salida.
* Basado en “Kitchen Fire Safety” publicado por NFPA.
4 49-80760-2
Cómo Retirar la Película Protectora de Envío y la Cinta de Embalaje
Con cuidado tome un extremo de la película protectora
de envío con los dedos y lentamente retire la misma de la
superficie del electrodoméstico. No utilice ningún producto
filoso para retirar la película. Retire toda la película antes de
usar el electrodoméstico por primera vez.
Para asegurar que no haya daños sobre el acabado del
producto, la forma más segura de retirar el adhesivo de la cinta
de embalaje en electrodomésticos nuevos es aplicando un
detergente líquido hogareño para lavar platos. Aplique con una
tela suave y deje que se seque. NOTA: Si la superficie aún no
se encuentra limpia, consulte sobre más opciones de limpieza
en la página 8.
NOTA: El adhesivo deberá ser eliminado de todas las partes.
No se puede retirar si se hornea con éste dentro.
INFORMACIÓN DE SEGURIDAD
INFORMACIÓN IMPORTANTE DE SEGURIDAD
LEA TODAS LAS INSTRUCCIONES ANTES DE USAR
LEA Y GUARDE ESTAS INSTRUCCIONES
ADVERTENCIA
PARA REDUCIR EL RIESGO DE
UN INCENDIO DE GRASA SOBRE UNA ESTUFA:
A. Nunca deje unidades de superficie desatendidas en
configuraciones de calor elevadas. Los alimentos que
hierven y se derraman provocan humo y derrames
grasosos que pueden prenderse fuego. Caliente los
aceites lentamente en configuraciones bajas o medias.
B. Siempre encienda el sistema de ventilación cuando
cocine con configuraciones de calor elevadas o cuando
flambee alimentos (por ej., Crepes Suzette, cerezas
Jubilee, carne flambeada a la pimienta en grano).
C. Limpie los ventiladores con frecuencia. No debe
permitirse la acumulación de grasa en el ventilador o en
el filtro.
D. Utilice el tamaño de recipiente adecuado. Siempre utilice
recipientes de cocción apropiados para el tamaño del
elemento de superficie.
ADVERTENCIA
A FIN DE REDUCIR EL
RIESGO DE INCENDIOS, DESCARGAS ELÉCTRICAS
O LESIONES PERSONALES, CUMPLA CON LO
SIGUIENTE:
A. El trabajo de instalación y el cableado eléctrico deben
ser realizados por una persona(s) calificada de acuerdo
con todos los códigos y estándares aplicables, incluyendo
construcciones resistentes al fuego.
B. Es necesario contar con suficiente cantidad de aire
para una combustión y salida de gases adecuadas a
través del conducto (chimenea) del equipo de consumo
de combustible, a fin de evitar ráfagas de aire. Siga las
pautas del fabricante del equipo de calefacción y los
estándares de seguridad, tales como aquellos publicados
por la Asociación Nacional de Protección contra
Incendios (National Fire Protection Association, NFPA), la
Sociedad Estadounidense para la Calefacción (American
Society for Heating), los Ingenieros de Refrigeración
y Acondicionadores de Aire (Refrigeration and Air
Conditioning Engineers, ASHRAE) y las autoridades de
los códigos locales.
C. Al cortar o perforar una pared o un cielorraso, no dañe el
cableado eléctrico y de otros servicios ocultos.
D. Los ventiladores con conducto siempre deben contar con
ventilación hacia el exterior.
E. Cuando corresponda, instale un sistema de reposición
(reemplazo) de aire de acuerdo con los requisitos
del código local de construcción. Para acceder a
soluciones relacionadas con la reposición de aire, visite
GEAppliances.com.
F. Desconecte el disyuntor de habitaciones adyacentes
mientras esté trabajando.
ADVERTENCIA
A FIN DE REDUCIR EL RIESGO
DE INCENDIOS, USE SÓLO CONDUCTOS DE METAL.
Ŷ1RLQWHQWHUHSDUDURUHHPSOD]DUQLQJXQDSDUWHGHOD
cocina, a menos que esto se recomiende específicamente
en este manual. Cualquier otra reparación deberá ser
realizada por un técnico calificado.
49-80760-2 5
Controles
USO DE LA CAMPANA: Controles
1. Panel de Control de la Campana Extractora:
El panel de control está ubicado en el frente de la base.
La posición y función de cada botón del control aparece
escrito debajo.
2. Botón de Luz: Interruptor On/Night/Off (Encendido/
Nocturno/ Apagado) para las luces halógenas. Presione el
botón LIGHT (Luz) para encender las luces, nuevamente
para ajustar las luces en la configuración nocturna, y
nuevamente para apagarlas.
3. Botón Fan Off (Ventilador Apagado): Interruptor
de apagado del ventilador. El ventilador puede ser usado
presionando cualquiera de los botones de configuración
del ventilador. Mantenga presionado durante 2 segundos
para activar la función de apagado automático luego de 15
minutos.
4. Botones de la Configuración del Ventilador:
Control de velocidad del ventilador. Presione el interruptor
de Lo para activar la velocidad en LOW (Baja), Med
para MEDIUM (Media) y Hi para HIGH (Alta). Mantenga
presionado el botón Hi (Alto) durante 2 segundos
para activar la función BOOST SPEED (Aumento de
Velocidad), la cual funcionará durante 10 minutos.
41
23
6 49-80760-2
USO DE LA CAMPANA: Controles
Sólo Para Instalación con Recirculación
Filtro de carbón (No Incluido)
Si el modelo no tiene ventilación hacia afuera, el aire será
recirculado a través de un filtro de carbón descartable que
ayude a retirar el humo y los olores.
NOTA: NO enjuague o coloque el filtro de carbón en el
lavavajillas automático.
El filtro de carbón no puede ser limpiado. Debe ser
reemplazado. Se recomienda que el filtro de carbón sea
reemplazado cada entre 6 y 12 meses, o si se encuentra
notoriamente sucio o descolorido.
Solicite el filtro de carbón JXCF72.
Para consultar sobre la compra de filtros de carbón de
repuesto o para encontrar la ubicación del distribuidor más
cercano a su domicilio, llame a nuestro número gratuito:
Centro nacional de piezas 800.626.2002
Para su instalación:
1. Retire los filtros metálicos – consulte la sección del filtro de
grasa metálico.
2. Coloque el lateral del filtro de carbón con las lengüetas
contra el costado del calefactor.
3. Alinee las líneas dobles del filtro de carbón con el símbolo
“desbloqueado” en el calefactor.
4. Presione y doble hacia abajo el filtro de carbón hasta que
las líneas dobles se alineen con el símbolo “bloqueado” en
el calefactor.
5. Repita este procedimiento con el segundo filtro del otro lado
del calefactor.
6. Reemplace los filtros metálicos – consulte la sección del
filtro de grasa metálico.
Para su retiro:
1. Retire los filtros metálicos – consulte la sección del filtro de
grasa metálico.
2. Doble los filtros de carbón hacia arriba a ambos lados del
motor, a fin de alinear las líneas dobles con el símbolo
“desbloqueado”. Los bloqueos están ahora desconectados y
los filtros de carbón pueden ser retirados.
Filtros (Modelos de Pirámide JVW5301, JVW5361)
Asegúrese de que la energía eléctrica esté apagada y que todas las superficies estén frías antes de limpiar o arreglar cualquier
pieza de la campana de ventilación.
Filtro de grasa metálico
Los filtros metálicos atrapan la grasa durante la cocción.
Filtro debe estar SIEMPRE en su lugar cuando la campana
esté en funcionamiento. El filtro de grasa es apto para
lavavajillas y debe limpiarse cada 6 meses, o según sea
necesario.
Para quitar:
Tire hacia abajo la traba del filtro para liberarlo.
Para volver a colocar:
Calce las lengüetas en la parte trasera del filtro, en las ranuras
de la parte trasera de la abertura del filtro. Levante el lado
frontal del filtro y presione de forma suave hasta que el filtro
quede bloqueado en su posición. Asegúrese de que el bloqueo
del filtro esté en la posición cerrada para asegurar el filtro.
Para limpiar el filtro, utilice agua jabonosa caliente y enjuague
con agua limpia o lávelo en el lavavajillas. No utilice productos
de limpieza abrasivos.
NOTA: En el lavavajillas se producirá una leve decoloración.
NOTA: Los modelos de
30” cuentan con 2 filtros
de grasa. Los modelos
de 36” cuentan con 3
filtros de grasa.
49-80760-2 7
Sólo Para Instalación con Recirculación
Filtro de carbón (No Incluido)
Si el modelo no tiene ventilación hacia afuera, el aire será
recirculado a través de un filtro de carbón descartable que
ayude a retirar el humo y los olores.
NOTA: NO enjuague o coloque el filtro de carbón en el
lavavajillas automático.
El filtro de carbón no puede ser limpiado. Debe ser
reemplazado. Se recomienda que el filtro de carbón sea
reemplazado cada entre 6 y 12 meses, o si se encuentra
notoriamente sucio o descolorido.
Solicite el filtro de carbón JXCF71.
Para consultar sobre la compra de filtros de carbón de
repuesto o para encontrar la ubicación del distribuidor más
cercano a su domicilio, llame a nuestro número gratuito:
Centro nacional de piezas 800.626.2002
Para su instalación:
1. Inserte las lengüetas con botón del filtro de carbón en las
dos ranuras que se encuentran en la parte trasera de la
unidad. Haga pivotar el filtro hacia arriba hasta su posición,
mientras empuja hacia abajo las lengüetas de bloqueo.
2. Reemplace el filtro metálico – consulte la sección del filtro
de grasa metálico.
Para su retiro:
1. Retire el filtro metálico – consulte la sección del filtro de
grasa metálico.
2. Presione las dos lengüetas del filtro de carbón para
desactivar el bloqueo y pivotar para el retiro.
Filtros (Modelos de Vidrio PVW7301, PVW7361)
USO DE LA CAMPANA: Filtros
Asegúrese de que la energía eléctrica esté apagada y que todas las superficies estén frías antes de limpiar o arreglar cualquier
pieza de la campana de ventilación.
Filtro de grasa metálico
El filtro metálico atrapa la grasa liberada por las comidas
durante su cocción.
Filtro debe estar SIEMPRE en su lugar cuando la campana
esté en funcionamiento. El filtro de grasa es apto para
lavavajillas y debe limpiarse cada 6 meses, o según sea
necesario.
Para quitar:
Tire hacia abajo la traba del filtro para liberarlo.
Para volver a colocar:
Coloque las lengüetas en la parte inferior del filtro, detrás del
estante de la apertura del filtro. Levante la cara frontal del filtro,
empuje hacia abajo el bloqueo del filtro, y empuje de forma
suave hasta que el filtro esté en su posición. Libere el bloqueo
del filtro para asegurar el mismo en su posición.
Para limpiar el filtro, utilice agua jabonosa caliente y enjuague
con agua limpia o lávelo en el lavavajillas. No utilice productos
de limpieza abrasivos.
NOTA:En el lavavajillas se producirá una leve decoloración.
Traba del filtro
8 49-80760-2
Lámparas (Modelos Pirámide JVW5301, JVW5361)
Superficies de acero inoxidable (en algunos modelos)
No utilice almohadillas de acero porque rayan la superficie.
Para limpiar la superficie de acero inoxidable, utilice agua
tibia jabonosa o un limpiador o lustrador de acero inoxidable.
Siempre limpie la superficie en dirección de la veta. Siga las
instrucciones del producto para limpiar la superficie de acero
inoxidable. Los limpiadores con ácido oxálico tales como Bar
Keepers Friend Soft Cleanser™ eliminarán el óxido sobre
la superficie, deslustres y pequeñas manchas. Use sólo un
limpiador líquido libre de material abrasivo y frote en la dirección
de las líneas del cepillo con una esponja suave y húmeda.
Para consultar sobre la compra de limpiadores o lustradores
de aparatos de acero inoxidable, o para encontrar la ubicación
del distribuidor más cercano, llame a nuestro número gratuito:
Centro nacional de piezas 800.626.2002
GEApplianceParts.com
Superficies Pintadas (en algunos modelos)
No use virutas de acero u otros limpiadores abrasivos;
estos rayarán la superficie.
De forma frecuente, limpie las superficies sucias de grasa.
Para limpiar la superficie de la campana, use una tela caliente
y húmeda con un detergente suave adecuado para superficies
pintadas. Se puede agregar aproximadamente una chuchara
sopera de amoníaco al agua. Use una tela limpia, caliente y
húmeda para eliminar el jabón. Seque con una tela limpia y seca.
NOTA: Al realizar la limpieza, tenga cuidado de no tener
contacto con los filtros y otras superficies no esmaltadas.
PRECAUCIÓN
Al limpiar las superficies de la
campana, asegúrese de no tocar la lámpara con las manos
húmedas o con una tela. Una lámpara tibia o caliente se
puede romper si es tocada con una superficie húmeda.
Siempre espere a que la lámpara se enfríe completamente
antes de hacer la limpieza alrededor de la misma.
PRECAUCIÓN
Espere a que las lámparas se
enfríen antes de tocar las mismas.
Para cambiar las lámparas:
1. Antes de intentar reemplazar una lámpara, asegúrese de
que su interruptor esté apagado.
2. Utilizando un destornillador de punta plana, desconecte
el soporte del cableado de la lámpara y de forma suave
empuje el soporte hacia abajo desde la campana.
3. Mientras sostiene la ficha, gire la lámpara en dirección de
las agujas del reloj para retirar la misma. Reemplace la
misma por una lámpara nueva GU-10. Asegúrese de que la
lámpara nueva esté bloqueada en la ficha.
4. Reemplace la ficha y la lámpara nueva en la campana y
coloque la misma en un soporte de lámparas.
Superficies
CUIDADO Y LIMPIEZA:
Superficies
/ Lámparas
49-80760-2 9
Lámparas (Modelos de Vidrio PVW7301, PVW7361)
CUIDADO Y LIMPIEZA: Lámparas
PRECAUCIÓN
Espere a que las lámparas se
enfríen antes de tocar las mismas.
Para cambiar las lámparas:
1. Antes de intentar reemplazar las lámparas, asegúrese de
que su interruptor esté apagado.
2. Utilice guantes. No toque la lámpara directamente con los
dedos. Los aceites para la piel pueden ocasionar fallas
tempranas en las lámparas. Use guantes limpios o use una
toalla de papel para sostener la lámpara.
3. Utilizando un destornillador de punta plana, desconecte el
anillo con borde metálico del soporte de la lámpara.
4. Retire la luz empujando hacia el frente de la campana.
Reemplace la misma por una lámpara con Cápsula
Halógena Clara G4 20W nueva, insertando las dos puntas
en los agujeros y presionando hacia la parte trasera de la
campana para asegurar la lámpara.
5. Vuelva a insertar el anillo con borde metálico alineando los
agujeros con las dos caras sobre el soporte de la lámpara,
con las dos lengüetas sobre el anillo con borde, y empuje
hacia arriba.
10 49-80760-2
Problema Causa Posible Qué Hacer
El ventilador/la luz no
funcionan cuando se
presionan los botones
El fusible puede haberse quemado o
el interruptor decircuitos puede haber
saltado.
Cambie los fusibles o reconfigure el interruptor de
circuitos.
El ventilador no
funciona cuando los
botones Lo (Bajo), Med
(medio) y High (Alto)
son presionados.
El conector del ventilador está suelto o
no se encuentra enchufado dentro de
su conector correspondiente.
Desconecte la electricidad hacia la unidad. Quite
los filtros y observe el ventilador. Si el enchufe
del conector del ventilador está suelto o si ve el
conector colgando, el instalador no lo enchufó
firmemente. Consulte el mini manual para conocer
la ubicación del enchufe y cómo enchufar el
conector.
Ruido de flujo de aire
muy elevado o anormal
Tamaño de conducto incorrecto
utilizado en la instalación.
Esta campana requiere un conducto de 6”
para funcionar de manera óptima. El uso de un
conducto más pequeño hará que la ventilación se
reduzca. Minimice la longitud del conducto y el
número de transiciones y codos. Los técnicos de
GE no pueden corregir este problema si hay
una instalación inadecuada.
El ventilador no hace
circular aire o desplaza
desplaza el aire más
despacio que lo normal
y/o hace ruido de
flujo de aire elevado o
anormal
Obstrucciones en el conducto. Verifique que no haya obstrucciones en la
ventilación. Controle que la cubierta de pared o
casquete de techo tengan una hoja o puerta.
El filtro de grasa metálico y el filtro
de carbón (si lo hubiera) pueden estar
sucios.
Asegúrese de que el regulador de tiro se mueva
libremente. Las hojas del regulador de tiro pueden
darse vuelta y no se abrirán por completo cuando
esto suceda. Ajústela con la posición original.
Es posible que el filtro de grasa
metálico y el filtro de carbón (de estar
presentes) estén sucios.
Limpie el filtro de grasa metálico y vuelva a colocar
el filtro de carbón (si lo hubiera). Ver Cuidado y
limpieza de la campana de ventilación.
Insuficiente reposición (reemplazo) de
aire
Se requiere suficiente reposición (reemplazo)
de aire para que los artefactos con salida de
aire funcionen de acuerdo con sus calificaciones
energéticas. Controle los códigos locales de
construcción, que podrán requerir o aconsejar
enfáticamente el uso de reposición de aire. Para
acceder soluciones de aire disponibles, visite
GEAppliances.com.
Los controles de la
campana no funcionan
correctamente
Error en el circuito lógico. Desconecte la electricidad de la campana
reconfigurando el interruptor de circuitos. Espere
30 segundos para que los controles vuelvan a
configurarse.
Falla temprana de la
lámpara
Reemplace las lámparas con las manos
descubiertas.
Reemplace las luces utilizando guantes que eviten
que los aceites de la piel tomen contacto con las
luces.
El voltaje de la lámpara es demasiado
alto.
Reemplace la misma por una con el voltaje
correcto.
¡Ahorre tiempo y dinero! Primero revise los cuadros que aparecen en las siguientes páginas y es posible que no necesite solicitar
reparaciones.
Consejos para la Solución de Problemas... Antes de solicitar el servicio técnico
CONSEJOS PARA LA SOLUCIÓN DE PROBLEMAS
49-80760-2 11
Notas
12 49-80760-2
Notas
49-80760-2 13
Notas
14 49-80760-2
Abroche su recibo aquí. Para acceder al servicio técnico de acuerdo con
la garantía deberá contar con la prueba de la fecha original de compra.
GEAppliances.com
Todo el servicio de garantía es provisto por nuestros Centros de Servicio de Fabricación, o un técnico autorizado de Customer Care®.
Para programar una visita del servicio técnico a través de Internet, visítenos en www.geappliances.com/service_and_support/, o
llame al 800.GE.CARES (800.432.2737). Cuando llame para solicitar el servicio, tenga los números de serie y modelo disponibles.
Para realizar el servicio técnico de su electrodoméstico, se podrá requerir el uso de datos del puerto de abordaje para su diagnóstico.
Esto da al técnico del servicio de fábrica de GE Appliances la habilidad de diagnosticar de forma rápida cualquier problema con
su electrodoméstico, y de ayudar a GE Appliances a mejorar sus productos al brindarle a GE Appliances la información sobre su
electrodoméstico. Si no desea que los datos de su electrodoméstico sean enviados a GE Appliances, solicitamos que le indique a su
técnico no entregar los datos a GE Appliances en el momento del servicio.
Qué no cubrirá GE Appliances:
Ŷ Viajes del técnico del servicio a su hogar para enseñarle
sobre cómo usar el producto.
Ŷ ,QVWDODFLyQHQWUHJDRPDQWHQLPLHQWRLQDGHFXDGRV
Ŷ )DOODVGHOSURGXFWRHQFDVRGHDEXVRPDOXVRPRGLILFDFLyQ
o uso para propósitos diferentes al original o uso comercial.
Ŷ 5HHPSOD]RGHIXVLEOHVGHODFDVDRUHLQLFLRGHGLV\XQWRUHV
Ŷ 'DxRVRFDVLRQDGRVVREUHHOSURGXFWRSRUDFFLGHQWH
incendio, inundaciones o catástrofes naturales.
Ŷ 'DxRVLQFLGHQWDOHVRFRQVHFXHQWHVFDXVDGRVSRUSRVLEOHV
defectos sobre este producto.
Ŷ 'DxRVVREUHHODFDEDGRWDOHVFRPRy[LGRVREUHOD
superficie, deslustres o manchas pequeñas no informadas
dentro de las 48 horas luego de la entrega.
Ŷ 'DxRFDXVDGRGHVSXpVGHODHQWUHJD
Ŷ 3URGXFWRQRDFFHVLEOHSDUDEULQGDUHOVHUYLFLRUHTXHULGR
Ŷ 0DUFDVRPDQFKDVLQFOX\HQGRPDQFKDVGHy[LGRVREUH
la superficie) que pueden ser eliminadas siguiendo las
instrucciones de limpieza.
Ŷ 6ROLFLWHHOVHUYLFLRWpFQLFRSDUDUHSDUDURUHHPSOD]DUODV
lámparas, excepto las lámparas LED.
GARANTÍA
Garantía de la Cocina Eléctrica de GE Appliances
EXCLUSIÓN DE GARANTÍAS IMPLÍCITAS
Su única y exclusiva alternativa es la reparación del producto, como se indica en la Garantía Limitada. Las
garantías implícitas, incluyendo garantías implícitas de comerciabilidad o conveniencia sobre un propósito
particular, se limitan a un año o al período más corto permitido por la ley.
Esta garantía se extiende al comprador original y a cualquier dueño subsiguiente de productos comprados para
uso hogareño dentro de EE.UU. Si el producto está en un área donde no se encuentra disponible un Proveedor
Autorizado del Servicio Técnico de GE Appliances, usted será responsable por el costo de un viaje o se podrá
requerir que traiga el producto a una ubicación del Servicio Técnico de GE Appliances autorizado para recibir el
servicio. En Alaska, la garantía excluye el costo de envío o llamadas del servicio a su hogar. Algunos estados
no permiten la exclusión o limitación de daños fortuitos o consecuentes. Esta garantía le da derechos legales
específicos y es posible que tenga otros derechos legales que varían entre un estado y otro. Para conocer cuáles son
sus derechos legales, consulte a la oficina de asuntos del consumidor local o estatal o al Fiscal de su estado.
Garante: GE Appliances, a Haier company
Garantías Extendidas: Adquiera una garantía extendida de GE Appliances y conozca los descuentos especiales que
están disponibles mientras su garantía aún está vigente. Puede acceder a la misma a través de Internet en cualquier
momento en
www.geappliances.com/service_and_support/shop-for-extended-service-plans.htm
o llamando al 800.626.2224 durante el horario comercial. Los Servicios para los GE Appliances aún estarán
disponibles cuando su garantía caduque.
Por el Período de GE Appliances reemplazará
Un Año
Desde la fecha de la
compra original
Cualquier pieza del producto de cocción que falle debido a un defecto en los materiales o la
fabricación. Durante esta garantía limitada de un año, GE Appliances también proveerá, sin costo,
todo el trabajo y costos del servicio relacionados con el reemplazo de la pieza defectuosa.
49-80760-2 15
ACCESORIOS
¿Busca Algo Más?
GE Appliances ofrece una variedad de accesorios para
mejorar sus experiencias de cocción y mantenimiento!
Para acceder a números telefónicos e información de sitios
Web, consulte la página de Soporte para el Consumidor.
Estos y otros productos están disponibles:
Accesorios
Piezas
Filtro de Carbón
Kit de la Cubierta del Conducto para Cielorrasos Altos
Control Remoto
Lámparas de Reemplazo
Suministros de Limpieza
Limpiadores de Acero Inoxidable CitriShine
Limpiador para Electrodomésticos de Acero Inoxidable CERAMA BRYTE®
Bar Keepers Friend Soft Cleanser™
16 49-80760-2
Soporte para el Consumidor
SOPORTE PARA EL CONSUMIDOR
Sitio Web de GE Appliances
¿Desea realizar una consulta o necesita ayuda con su electrodoméstico? ¡Intente a través del Sitio Web de GE Appliances las
24 horas del día, cualquier día del año! Usted también puede comprar más electrodomésticos maravillosos de GE Appliances y
aprovechar todos nuestros servicios de soporte a través de Internet, diseñados para su conveniencia.
En EE.UU.: GEAppliances.com
Registre su Electrodoméstico
¡Registre su electrodoméstico nuevo a través de Internet, según su conveniencia! Un registro puntual de su producto permitirá
una mejor comunicación y un servicio más puntual de acuerdo con los términos de su garantía, en caso de surgir la necesidad.
También puede enviar una carta en la tarjeta de inscripción preimpresa que se incluye con el material embalado.
En EE.UU.: GEAppliances.com/register
Servicio Programado
El servicio de reparación de expertos de GE Appliances está a sólo un paso de su puerta. Conéctese a través de Internet y programe
su servicio a su conveniencia cualquier día del año. En EE.UU.: GEAppliances.com/ge/service-and-support/service.htm
o comuníquese al 800.432.2737 durante el horario de atención comercial.
Garantías Extendidas
Adquiera una garantía extendida de GE Appliances y conozca los descuentos especiales que están disponibles mientras su
garantía aún está vigente. La puede adquirir en cualquier momento a través de Internet. Los servicios de GE Appliances aún
estarán allí cuando su garantía caduque.
En EE.UU.: GEAppliances.com/ge/service-and-support/shop-for-extended-service-plans.htm
o comuníquese al 800.626.2224 durante el horario de atención comercial.
Conectividad Remota
Para solicitar asistencia para la conectividad de red inalámbrica (para modelos con acceso remoto),
visite nuestro sitio web en GEAppliances.com/ge/connected-appliances/ o comuníquese al 800.220.6899 en EE.UU.
Piezas y Accesorios
Aquellos individuos calificados para realizar el servicio técnico de sus propios electrodomésticos podrán solicitar el envío de
piezas o accesorios directamente a sus hogares (se aceptan las tarjetas VISA, MasterCard y Discover). Ordene hoy a través de
Internet durante las 24 horas, todos los días. En EE.UU.: GEApplianceparts.com o de forma telefónica al 877.959.8688 durante
el horario de atención comercial.
Las instrucciones que figuran en este manual cubren los procedimientos que serán realizados por cualquier usuario.
Otros servicios técnicos generalmente deben ser derivados a personal calificado del servicio. Se deberá tener cuidado,
ya que una reparación indebida podrá hacer que el funcionamiento no sea seguro.
Contáctenos
Si no se encuentra satisfecho con el servicio que recibió de GE Appliances, comuníquese con nosotros a través de nuestro sitio
Web con todos los detalles, incluyendo su número telefónico, o escriba a:
En EE.UU.: General Manager, Customer Relations | GE Appliances, Appliance Park | Louisville, KY 40225
GEAppliances.com/ge/service-and-support/contact.htm
1 / 1

GE JVW5301 El manual del propietario

Categoría
Campanas de cocina
Tipo
El manual del propietario

En otros idiomas