Simplicity 613277-0110-E1 Manual de usuario

Marca: Simplicity

Modelo: 613277-0110-E1

Categoría: Accesorios para vehículos de motor

Tipo: Manual de usuario

Este manual también es adecuado para

Operator's Manual

Betjeningsvejledning

Bedienungsanleitung

Εγχειρίδιο χρήσ

Manual del operador

Käyttäjän käsikirja

Manuel d'utilisation

Manuale dell’Operatore

Gebruiksaanwijzing

Brukerhåndbok

Manual do Operador

Instruktionsbok

Models:613200, 61H200, 61H300

Revision A

Not for

Reproduction

2 vanguardpower.com

Not for

Reproduction

General Information

This manual contains safety information so that you will know the hazards and risks

related to this engine and how to prevent them. It also contains instructions for the

correct use and maintenance of the engine. Because Briggs & Stratton does not know

what equipment this engine will power, it is important that you read, understand, and

obey these instructions. Save these original instructions for future reference.

NOTE:The figures and illustrations in this manual are for reference only and can be

different from your model. If you need help, contact an Authorized Service Dealer.

For replacement parts or technical help, record the date of purchase, engine model,

type, trim, and the engine serial number. These numbers are located on your engine.

Refer to the Features and Controls section.

Date of Purchase

Engine Model - Type - Trim

Engine Serial Number

European Office Contact Information

For questions related to European emissions, contact our European office at:

Max-Born-Straße 2, 68519 Viernheim, Germany.

European Union (EU) Stage V (5): Carbon

Dioxide (CO2) Values

Enter CO2 in the search window on BriggsandStratton.com to find carbon dioxide values

of Briggs & Stratton EU Type-Approval Certificate engines.

Recycling Information

Recycle all cartons, boxes, used oil, and batteries as

specified by government regulations.

Operator Safety

Safety Alert Symbol and Signal Words

The safety alert symbol identifies safety information about hazards that could

result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used to

indicate the likelihood and the potential severity of injury. In addition, a hazard symbol

is used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or serious

injury.

CAUTION indicates a hazard which, if not avoided, could result in minor or moderate

injury.

NOTICE indicates information considered important but not hazard-related.

Hazard Symbols and Meanings

Safety information about

hazards that can result in

personal injury.

Read and understand the

Operator's Manual before

operating or servicing the

unit.

Fire Hazard Explosion Hazard

Shock Hazard Toxic Fume Hazard

Hot Surface Hazard Noise Hazard - Ear

protection recommended

for extended use.

Thrown Object Hazard -

Wear eye protection.

Explosion Hazard

Frostbite Hazard Kickback Hazard

Amputation Hazard -

Moving Parts

Chemical Hazard

Thermal Heat Hazard Corrosive Hazard

Safety Messages

WARNING

Briggs & Stratton® Engines are not designed for and are not to be used to power:

fun-karts; go-karts; children's, recreational, or sport all-terrain vehicles (ATVs);

motorbikes; hovercraft; aircraft products; or vehicles used in competitive events not

sanctioned by Briggs & Stratton. For information about competitive racing products, see

www.briggsracing.com. For use with utility and side-by-side ATVs, please contact Briggs

& Stratton Power Application Center, 1-866-927-3349. Incorrect engine use could result

in serious injury or death.

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

When you add fuel

• Stop the engine. Before you remove the fuel cap, wait a minimum of two (2) minutes

to make sure that the engine is cool.

• Fill the fuel tank outdoors or in an area that has good airflow.

• Do not put too much fuel in the tank. For expansion of the fuel, do not fill above the

bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks or

leaks. Replace damaged parts.

• If fuel spills, wait until it dries before you start the engine.

When you start the engine

• Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped) are

correctly installed.

• Do not crank the engine with the spark plug removed.

• If the engine is flooded, set the choke (if equipped) to the OPEN or RUN position.

Move the throttle (if equipped) to the FAST position and crank until the engine starts.

• If there is natural or LP gas leakage in the area, do not start the engine.

• Because vapors are flammable, do not use pressurized starter fluids.

When you operate the equipment

• Do not tilt the engine or the equipment at an angle which causes fuel to spill.

• Do not choke the carburetor (if equipped) to stop the engine.

• Do not start or operate the engine with the air cleaner (if equipped) or the air filter (if

equipped) removed.

When you do maintenance

• If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not

empty, fuel leakage can occurand could result a fire or an explosion.

• During maintenance if it is necessary to tilt the unit, make sure that the fuel tank, if

mounted on the engine, is empty and that the spark plug side is up. If the fuel tank is

not empty, leakage can occurand could result a fire or an explosion.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks or

leaks. Replace damaged parts.

• Do not change the governor spring, links or other parts to increase engine speed.

• Do not hit the flywheel with a hammer or hard object. This could result in failure of the

flywheel during operation.

• Replacement parts must be of the same design and installed in the same position as

the original parts. Other parts could result in damage or an injury.

When you move the location of equipment

• Make sure that the fuel tank is EMPTY or that the fuel shut-off valve is in the

CLOSED position.

Not for

Reproduction

When fuel or equipment is in storage with fuel in the fuel tank

• Because pilot lights or other ignition sources can cause explosions, keep fuel or

equipment away from furnaces, stoves, water heaters or other appliances that have

pilot lights.

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

Engine start-up causes spark that could result in a fire or explosion.

• If there is natural or LP gas leakage in the area, do not start the engine.

• Because vapors are flammable, do not use pressurized starter fluids.

WARNING

POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a

poisonous gas that could kill you in minutes. Although you do not smell exhaust

fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel

sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY. See

a doctor. You may have carbon monoxide poisoning.

• Carbon monoxide gas can collect in occupied spaces. To reduce the risk of carbon

monoxide gas, ONLY operate this product outdoors and far away from windows,

doors and vents.

• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide alarms

with battery back-up as specified by the manufacturer's instructions. Smoke alarms

cannot sense carbon monoxide gas.

• DO NOT operate this product in homes, garages, basements, crawlspaces, sheds, or

other closed spaces, even if you use fans or open doors and windows for ventilation.

After the operation of this product, carbon monoxide can quickly collect in these

spaces and stay for hours.

• ALWAYS put this product downwind and point the engine exhaust away from

occupied spaces.

WARNING

Fast retraction of the starter cord (kickback) will pull your hand and arm to the

engine faster than you can let go.Broken bones, fractures, bruises or sprains

could result.

• To prevent kickback when you start the engine, pull the starter cord slowly until

resistance is felt and then pull quickly.

• Before you start the engine, disconnect or remove all external equipment and engine

loads.

• Make sure that direct-coupled equipment components, such as, but not limited to,

blades, impellers, pulleys, and sprockets, are correctly attached.

WARNING

Rotating parts can entangle hands, feet, hair, clothing, or accessories and result

in traumatic amputation or laceration.

• Operate equipment with the guards correctly installed.

• Keep hands and feet away from rotating parts.

• Remove jewelry and make sure that long hair is away from all rotating parts.

• Do not wear loose clothes or items that could become caught.

WARNING

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

Combustible materials, such as leaves, grass and brush, can catch fire.

• Before you touch the engine or muffler, stop the engine and wait two (2) minutes.

Make sure that the engine and muffler are safe to touch.

• Remove debris from the muffler and engine.

It is a violation of California Public Resource Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in section 4442, maintained in

effective working order. Other states or federal jurisdictions may have similar laws;

reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust

system installed on this engine.

WARNING

Accidental engine spark can cause an electric shock or fire and could result in

entanglement, traumatic amputation or laceration.

Before you make adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the spark plug.

• Disconnect the battery wire from the negative battery terminal (only engines with

electric start.)

• Use only the correct tools.

When you check for spark:

• Use an approved spark plug tester.

• Do not check for spark with the spark plug removed.

WARNING

Fuel vapors are flammable and explosive. Fire or explosion could result in burns

or death.

If you smell gas

• Do not start the engine.

• Do not switch on electrical switches.

• Do not use a phone in the vicinity.

• Evacuate the area.

• Contact the gas supplier or the fire department.

Features and Controls

Engine Controls

Compare the callout letters in Figures 1 and 2 to the engine controls in the list that

follows:

A. Engine Identification Numbers Model - Type - Code

B. Spark Plug

C. Air Cleaner, Low Profile

D. Dipstick

E. Oil Fill

F. Oil Filter

G. Oil Drain Plug

H. Oil Pressure Sensor

I. Air Intake Grille

J. Electric Starter

K. Starter Solenoid

L. Regulator / Rectifier

M. LPG /NG Mixer

N. Oil Cooler (if equipped)

O. Muffler (if equipped)

Engine Control Symbols and Meanings

Engine Speed - FAST Engine Speed - SLOW

Engine Speed - STOP ON - OFF

Operation

Oil Recommendations

Oil Capacity: See the Specifications section.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers or

dealers could have added oil to the engine. Before you start the engine for the first time,

make sure that the oil is at the correct level. Add oil as specified by the instructions in

this manual. If you start the engine without oil, damage will occur and the engine will not

be repaired under warranty.

4 vanguardpower.com

Not for

Reproduction

We recommend the use of Briggs & Stratton

Warranty Certified oils for best

performance. Other high-quality detergent oils are permitted if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Use the chart to select the best viscosity for the outdoor temperature range expected.

Engines on most outdoor power equipment operate well with 5W-30 Synthetic oil. For

equipment operated in hot temperatures, Vanguard

15W-50 Synthetic oil gives the best

protection.

A SAE 30 - Below 40 °F (4 °C) the use of SAE 30 will result in hard starting.

B 10W-30 - Above 80 °F (27 °C) the use of 10W-30 may cause increased oil

consumption. Checkthe oil level frequently.

C 5W-30

D Synthetic 5W-30

Vanguard

Synthetic 15W-50

Check and Add Oil

Before you check or add oil

• Make sure the engine is level.

• Clean the oil fill area of debris.

• Refer to the Specifications section for oil capacity.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers or

dealers could have added oil to the engine. Before you start the engine for the first time,

make sure that the oil is at the correct level. Add oil as specified by the instructions in

this manual. If you start the engine without oil, damage will occur and the engine will not

be repaired under warranty.

1. Remove the dipstick (A, Figure 3) and clean with a cloth.

2. Install and tighten the dipstick (A, Figure 3).

3. Remove the dipstick and check the oil level. Make sure that the oil level is at the

top of the full indicator (B, Figure 3) on the dipstick.

4. If the oil level is low, slowly add oil into the engine oil fill (C, Figure 3). Do not add

too much oil. After you add oil, wait one minute and check the oil level again. Make

sure that the oil level is correct.

5. Install and tighten the dipstick (A, Figure 3).

Low Oil Protection System (if equipped)

A low oil sensor is installed on some engines. If the oil is low, the sensor will display a

warning light or stop the engine. Stop the engine and follow these steps before you start

the engine.

• Make sure the engine is level.

• Do an oil check. Refer to the Check Oil Level section.

• If the oil level is low, add the correct amount of oil. Start the engine and make sure

the warning light (if equipped) does not come on.

• If the oil level is not low, do not start the engine. Contact a Briggs & Stratton

Authorized Service Dealer to have the oil problem corrected.

Fuel Recommendations

WARNING

Missing or inoperative automatic safety "fuel lock-off" valve can cause a fire or

explosion.

• DO NOT operate the equipment if the automatic safety "fuel lock-off" valve is missing

or inoperative.

Fuel must meet these requirements

• Use clean, dry fuel, free of moisture or any particulate material. Using fuels outside

the recommended values can cause performance problems.

• In engines set up to operate on LPG, commercial grade HD5 LPG is recommended.

Recommended fuel composition is fuel with a minimum fuel energy of 2500 BTU's/ft³

with maximum propylene content of 5% and butane and heavier gas content of 2.5%

and minimum propane content of 90%.

NG or LPG engines are certified to operate on natural or liquid propane gas. The

emissions control system for this engine is EM (Engine Modifications).

Add Fuel

WARNING

Fuel vapors are flammable and explosive. Fire or explosion could result in burns

or death.

When you add fuel

• Fill the fuel tank outdoors or in an area that has good airflow.

• Frequently examine the fuel lines, fuel tank, and connections for cracks or leaks.

Replace damaged parts.

For information on refueling natural or LP gas engines, read the operating instructions

supplied by the equipment manufacturer.

Start the Engine

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

When you start the engine

• Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped) are

correctly installed.

• Do not crank the engine with the spark plug removed.

• If the engine is flooded, set the choke (if equipped) to the OPEN or RUN position.

Move the throttle (if equipped) to the FAST position and crank until the engine starts.

• If there is natural or LP gas leakage in the area, do not start the engine.

• Because vapors are flammable, do not use pressurized starter fluids.

WARNING

POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a

poisonous gas that could kill you in minutes. Although you do not smell exhaust

fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel

sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY. See

a doctor. You may have carbon monoxide poisoning.

• Carbon monoxide gas can collect in occupied spaces. To reduce the risk of carbon

monoxide gas, ONLY operate this product outdoors and far away from windows,

doors and vents.

• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide alarms

with battery back-up as specified by the manufacturer's instructions. Smoke alarms

cannot sense carbon monoxide gas.

• DO NOT operate this product in homes, garages, basements, crawlspaces, sheds, or

other closed spaces, even if you use fans or open doors and windows for ventilation.

After the operation of this product, carbon monoxide can quickly collect in these

spaces and stay for hours.

• ALWAYS put this product downwind and point the engine exhaust away from

occupied spaces.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers or

dealers could have added oil to the engine. Before you start the engine for the first time,

make sure that the oil is at the correct level. Add oil as specified by the instructions in

this manual. If you start the engine without oil, damage will occur and the engine will not

be repaired under warranty.

NOTE:Your equipment could have remote controls. Refer to the equipment manual for

location and operation of remote controls

For information on how to start the engine, read the operation instructions supplied by

the equipment manufacturer.

Stop the Engine

For information on how stop the engine, read the operation instructions supplied by the

equipment manufacturer.

Not for

Reproduction

Maintenance

Maintenance Information

WARNING

During maintenance if it is necessary to tilt the unit, make sure that the fuel tank, if

mounted on the engine, is empty and that the spark plug side is up. If the fuel tank is not

empty, leakage can occur and could result in a fire or an explosion. If the engine is tilted

in a different direction, it will not easily start because of oil or fuel contamination of the air

filter or the spark plug.

We recommend that you see a Briggs & Stratton Authorized Service Dealer for all

maintenance and servicing of the engine and engine parts.

NOTICE

All the components used to build this engine must remain in place for correct operation.

WARNING

Accidental engine spark can cause an electric shock or fire and could result in

entanglement, traumatic amputation or laceration.

Before you make adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the spark plug.

• Disconnect the battery wire from the negative battery terminal (only engines with

electric start.)

• Use only the correct tools.

When you check for spark:

• Use an approved spark plug tester.

• Do not check for spark with the spark plug removed.

Emissions Control Service

For maintenance, replacement, or repair of emissions control devices and

systems, contact a qualified off-road engine repair establishment or service

technician. However, for "no charge" emissions control service, the work must be done

by a factory authorized dealer. Refer to the Emissions Control Statements.

Maintenance Schedule

Intervals of 8 Hours or Daily

• Check the engine oil level.

• Clean the area around the muffler and controls.

Intervals of 100 Hours or Annually

• Replace the spark plugs.

• Change the engine oil.

• Replace the oil filter (if equipped).

•

Service the air filter

•

Clean the pre-cleaner (if equipped)

• Service the exhaust system.

• Check the valve clearance. Adjust if necessary.

Intervals of 400 Hours or Annually

• Replace the air filter.

•

Service the cooling system

•

Clean the oil cooler fins

In dusty conditions or when the airborne is present, clean more often.

Servicing the Spark Plug

Check the spark plug gap (A, Figure 4) with a wire gauge (B). If necessary, set the

spark plug gap. Install and tighten the spark plug to the correct torque. For gap or torque

specifications, refer to the Specifications section.

NOTE:In some areas, it is mandatory by local law that you use a resistor spark plug

to decrease ignition signals.If a resistor spark plug was installed by the equipment

manufacturer, use the same type for replacement.

Servicing theExhaust System

WARNING

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

Combustible materials, such as leaves, grass and brush, can catch fire.

• Before you touch the engine or muffler, stop the engine and wait two (2) minutes.

Make sure that the engine and muffler are safe to touch.

• Remove debris from the muffler and engine.

It is a violation of California Public Resource Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in section 4442, maintained in

effective working order. Other states or federal jurisdictions may have similar laws;

reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust

system installed on this engine.

Remove debris from the muffler and cylinder area. Examine the muffler for cracks,

corrosion, or other damage. Remove the deflector or the spark arrester, if equipped, and

examine for damage or carbon blockage. If damage is found, install the replacement

parts before you operate the equipment.

WARNING

Replacement parts must be of the same design and installed in the same position as the

original parts. Other parts could result in damage or an injury.

Change Engine Oil

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

• If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not

empty, fuel leakage can occur and cause a fire or an explosion.

• Before you touch the engine or muffler, stop the engine and wait two (2) minutes.

Make sure that the engine and muffler are safe to touch.

Used oil is a hazardous waste product and must be discarded of correctly. Do not

discard with household waste. Contact your local authorities, service center, or dealer

for safe disposal or recycling facilities.

Remove Oil

1. With engine OFF but warm, disconnect the spark plug wire(s)(D, Figure 5), and

keep it away from the spark plug(s)(E).

2. Remove the dipstick (A, Figure 6).

3. Remove the oil drain plug (F, Figure 7). Drain the oil into an approved container.

4. Install and tighten the oil drain plug(F, Figure 7).

Change Oil Filter, if equipped

1. Drain the oil from the engine. Refer to the Remove Oil section.

2. Remove the oil filter (H, Figure 8) anddiscard correctly.

3. Before you install the new oil filter, lightly lubricate the oil filter gasket withclean oil.

4. Install the oil filter by hand until the gaskettouchesthe oil filter adapter, then tighten

the oil filter 1/2 to 3/4 turns.

5. Add oil. Refer to the Add Oil section.

6. Start and operatethe engine. When the engine is warm, do a checkfor oil leaks.

7. Stop the engine. Make sure thatoil level is at the top of the full indicator (B, Figure

3) on the dipstick.

Add Oil

• Make sure the engine is level.

• Clean the oil fill area of all debris.

• Refer to the Specifications section for oil capacity.

1. Remove the dipstick (A, Figure 6). Remove oil from the dipstick with a clean cloth.

2. Slowly add oil into the engine oil fill (C, Figure 6). Do not overfill. Wait one minute

and then check the oil level.

3. Install and tighten the dipstick (A, Figure 6).

4. Remove the dipstick and check the oil level. The correct oil level is at the top of the

full indicator (B, Figure 6) on the dipstick.

6 vanguardpower.com

Not for

Reproduction

5. Install and tighten the dipstick (A, Figure 6).

6. Connect the spark plug wire(s) (D, Figure 5) to the spark plug(s) (E).

Servicing the Air Filter

WARNING

Fuel vapors are flammable and explosive. Fire or explosion could result in burns

or death.

• Do notstart and operate the engine with the air cleaner assembly (if equipped) or the

air filter (if equipped) removed.

NOTICE

Do not use pressurized air or solvents to clean the filter. Pressurized air could result in

damage to the filter and solvents will dissolve the filter.

See the Maintenance Schedule for service requirements.

Different models will use a foam or a paper filter. Some models could also have an

optional pre-cleaner that can be washed and used again. Compare the illustrations in

this manual with the type installed on your engine and service as follows.

Low Profile Air Filter

1. Remove the fastener(s) (A, Figure 9).

2. Remove the cover (B, Figure 9).

3. Remove the fastener(s) (C, Figure 9) and retainer (D).

4. Remove the air filter (E, Figure 9).

5. Remove the pre-cleaner (F, Figure 9), if equipped, from the air filter (E).

6. To loosen debris, lightly tap the air filter (E, Figure 9) on a hard surface. If the air

filter is dirty, replace with a new air filter.

7. Clean the pre-cleaner (F, Figure 9), if equipped, in liquid detergent and water. Make

sure the pre-cleaner is fully dry. Do not lubricate the pre-cleaner.

8. Assemble the dry pre-cleaner (F, Figure 9), if equipped, to the air filter (E).

9. Install the air filter (E, Figure 9) with the retainer (D) and fastener(s) (C).

10. Install the cover (B, Figure 9) with the fastener(s) (A). Make sure the fastener(s) is

tight.

Servicing the Cooling System

WARNING

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

Combustible debris, such as leaves, grass, and brush can catch fire.

• Before you touch the engine or muffler, stop the engine and wait two (2) minutes.

Make sure that the engine and muffler are safe to touch.

• Remove debris from the muffler and engine.

NOTICE

Do not use water to clean the engine. Water could cause contamination of the fuel

system. Use a brush or dry cloth to clean the engine.

This is an air cooled engine. Dirt or debris can prevent air flow and cause the engine to

become too hot and result in unsatisfactory performance and decreased engine life.

1. Use a brush or dry cloth to remove debris from the air intake grille.

2. Keep linkage, springs, and controls clean.

3. Keep the area around and behind the muffler, if equipped, free of combustible

debris.

4. Make sure the oil cooler fins, if equipped, are clean.

After a period of time, the cylinder cooling fins can collect debris and cause the engine

to overheat. This debris cannot be removed without partial disassembly of the engine.

Have a Briggs & Stratton Authorized Service Dealer inspect and clean the air cooling

system as recommended in the Maintenance Schedule.

Storage

Gaseous Engines

WARNING

Gaseous vapors are flammable and explosive. Fire or explosion could result in

burns or death.

Fuel Storage

• Because pilot lights or other ignition sources can cause explosions, keep fuel or

equipment away from furnaces, stoves, water heaters or other appliances that have

pilot lights.

Engine Oil

While the engine is warm, change the engine oil. Refer to Change the Engine Oil

section.

Troubleshooting

Assistance

For assistance, contact your local dealer or go to vanguardpower.com or call

1-800-999-9333 (in USA).

Specifications

Specificationsand Service Parts

Models: 613200, 61H200

Displacement 60.60 ci (993 cc)

Bore 3.366 in ( 85,5 mm)

Stroke 3.406 in (86,5 mm)

Oil Capacity 78 - 80 oz (2,3 - 2,4 L)

Spark Plug Gap .020 in (,51 mm)

Spark Plug Torque 180 lb-in (20 Nm)

Armature Air Gap .005 - .008 in (,13 - ,20 mm)

Intake Valve Clearance .004 - .006 in(,10 - ,15 mm)

Exhaust Valve Clearance .007 - .009 in (,18 - ,23 mm)

Model: 61H300

Displacement 60.60 ci (993 cc)

Bore 3.366 in ( 85,5 mm)

Stroke 3.406 in (86,5 mm)

Oil Capacity 78 - 80 oz (2,3 - 2,4 L)

Spark Plug Gap 0.030 in (,76 mm)

Spark Plug Torque 180 lb-in (20 Nm)

Armature Air Gap .005 - .008 in (,13 - ,20 mm)

Intake Valve Clearance .004 - .006 in(,10 - ,15 mm)

Exhaust Valve Clearance .007 - .009 in (,18 - ,23 mm)

Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and

1% for each 10° F (5.6° C) above 77° F (25° C). The engine will operate satisfactorily

at an angle up to 15°. Refer to the equipment Operator's Manual for safe permitted

operating limits on slopes.

Service Parts - Models:613200, 61H200, 61H300

Service Part Part Number

Air Filter, Low Profile - Generator UL

841856

Pre-cleaner, Low Profile 692520

Oil - SAE 30 100028

Oil Filter 842921

Fuel Filter 695666

Resistor Spark Plug - (Models: 613200,

61H200)

491055

Resistor Spark Plug - (Model: 61H300) 792015

Long Life Platinum Spark Plug 5066

Spark Plug Wrench 19374

Spark Tester 19368

We recommend that you see a Briggs & Stratton Authorized Dealer for maintenance

and servicing of the engine and engine parts.

Power Ratings

The gross power rating for individual gasoline engine models is labeled in accordance

with SAE (Society of Automotive Engineers) code J1940 Small Engine Power & Torque

Rating Procedure, and is rated in accordance with SAE J1995. Torque values are

derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM

for all others; horsepower values are derived at 3600 RPM. The gross power curves

can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with

exhaust and air cleaner installed whereas gross power values are collected without

these attachments. Actual gross engine power will be higher than net engine power and

is affected by, among other things, ambient operating conditions and engine-to-engine

Not for

Reproduction

variability. Given the wide array of products on which engines are placed, the gasoline

engine may not develop the rated gross power when used in a given piece of power

equipment. This difference is due to a variety of factors including, but not limited to, the

variety of engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel

pump, etc.), application limitations, ambient operating conditions (temperature, humidity,

altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations,

Briggs & Stratton may substitute an engine of higher rated power for this engine.

Warranty

Briggs & Stratton Engine Warranty

Effective January 2019

Limited Warranty

Briggs & Stratton warrants that, during the warranty period specified below, it will repair

or replace, free of charge, any part that is defective in material or workmanship or

both. Transportation charges on product submitted for repair or replacement under this

warranty must be borne by purchaser. This warranty is effective for and is subject to

the time periods and conditions stated below. For warranty service, find the nearest

Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.COM.

The purchaser must contact the Authorized Service Dealer, and then make the product

available to the Authorized Service Dealer for inspection and testing.

There is no other express warranty. Implied warranties, including those of

merchantability and fitness for a particular purpose, are limited to the warranty

period listed below, or to the extent permitted by law. Liability for incidental or

consequential damages are excluded to the extent exclusion is permitted by law. Some

states or countries do not allow limitations on how long an implied warranty lasts,

and some states or countries do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation and exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other rights which

vary from state to state and country to country

Standard Warranty Terms

1, 2, 3

Vanguard®; Commercial Series

Consumer Use - 36 months

Commercial Use - 36 months

XR Series

Consumer Use - 24 months

Commercial Use - 24 months

All Other Engines Featuring Dura-Bore™ Cast Iron Sleeve

Consumer Use - 24 months

Commercial Use - 12 months

All Other Engines

Consumer Use - 24 months

Commercial Use - 3 months

These are our standard warranty terms, but occasionally there may be additional

warranty coverage that was not determined at time of publication. For a listing

of current warranty terms for your engine, go to BRIGGSandSTRATTON.com or

contact your Briggs & Stratton Authorized Service Dealer.

There is no warranty for engines on equipment used for prime power in place

of a utility; standby generators used for commercial purposes, utility vehicles

exceeding 25 MPH, or engines used in competitive racing or on commercial or

rental tracks.

Vanguard installed on standby generators: 24 months consumer use, no

warranty commercial use. Commercial Series with manufacturing date before July

2017: 24 months consumer use, 24 months commercial use.

In Australia - Our goods come with guarantees that cannot be excluded under

the Australian Consumer Law. You are entitled to a replacement or refund for a

major failure and for compensation for any other reasonably foreseeable loss or

damage. You are also entitled to have the goods repaired or replaced if the goods

fail to be of acceptable quality and the failure does not amount to a major failure.

For warranty service, find the nearest Authorized Service Dealer in our dealer

locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by

emailing or writing to [email protected], Briggs & Stratton

Australia Pty Ltd, 1 Moorebank Avenue, Moorebank, NSW , Australia, 2170.

The warranty period begins on the original date of purchase by the first retail or

commercial consumer. "Consumer use" means personal residential household use by a

retail consumer. "Commercial use" means all other uses, including use for commercial,

income producing or rental purposes. Once an engine has experienced commercial

use, it shall thereafter be considered as a commercial use engine for purposes of this

warranty.

Save your proof of purchase receipt. If you do not provide proof of the initial

purchase date at the time warranty service is requested, the manufacturing date

of the product will be used to determine the warranty period. Product registration

is not required to obtain warranty service on Briggs & Stratton products.

About Your Warranty

This limited warranty covers engine-related material and/or workmanship issues only,

and not replacement or refund of the equipment to which the engine may be mounted.

Routine maintenance, tune-ups, adjustments, or normal wear and tear are not covered

under this warranty. Similarly, warranty is not applicable if the engine has been altered

or modified or if the engine serial number has been defaced or removed. This warranty

does not cover engine damage or performance problems caused by:

1. The use of parts that are not original Briggs & Stratton parts;

2. Operating the engine with insufficient, contaminated, or an incorrect grade of

lubricating oil;

3. The use of contaminated or stale fuel, gasoline formulated with ethanol greater than

10%, or the use of alternative fuels such as liquefied petroleum or natural gas on

engines not originally designed/manufactured by Briggs & Stratton to operate on

such fuels;

4. Dirt which entered the engine because of improper air cleaner maintenance or re-

assembly;

5. Striking an object with the cutter blade of a rotary lawn mower, loose or improperly

installed blade adapters, impellers, or other crankshaft coupled devices, or

excessive v-belt tightness;

6. Associated parts or assemblies such as clutches, transmissions, equipment

controls, etc., which are not supplied by Briggs & Stratton;

7. Overheating due to grass clippings, dirt and debris, or rodent nests which plug or

clog the cooling fins or flywheel area, or by operating the engine without sufficient

ventilation;

8. Excessive vibration due to over-speeding, loose engine mounting, loose or

unbalanced cutter blades or impellers, or improper coupling of equipment

components to the crankshaft;

9. Misuse, lack of routine maintenance, shipping, handling, or warehousing of

equipment, or improper engine installation.

Warranty service is available only through Briggs & Stratton Authorized Service

Dealers. Locate your nearest Authorized Service Dealer in our dealer locator map

at BRIGGSandSTRATTON.COM or by calling 1-800-233-3723 (in USA).

80004537 (Rev. F)

Briggs & Stratton Emissions Warranty

U.S. EPA, and Briggs & Stratton, LLC Emissions Control Warranty Statement for

Emergency Standby Engines - Your Warranty Rights and Obligations

General Information

The U.S. EPA, and Briggs & Stratton (B&S) are pleased to explain the emissions

control system warranty on your Model Year 2020-2022 and later engine / equipment.

In the U.S., new Emergency Standby Engines must be designed, built, and equipped to

meet stringent emission standards. Engines less than 25 Hp must meet requirements

of 40 CFR Part 1054. Engines greater than 25 Hp and less than 130 Hp must meet

requirements of 40 CFR Part 60 JJJJ. B&S must warrant the emissions control system

on your engine / equipment.

See Definition of appropriate use of Emergency Standby below.

The emission-related warranty covers all components whose failure would increase an

engine’s non-evaporative emissions of any regulated pollutant referenced below.

Manufacturer's Warranty Coverage:

Briggs & Stratton warrants that the engine is free from defects in material and

workmanship, and is also designed, built, and equipped to conform to applicable

regulations under Section 213 of the Clean Air Act, from the time the engine is sold,

until the expiration of its warranty period.

This warranty applies to all emission related engine components whose failure would

cause engine exhaust emissions to be out of EPA compliance. Further, this warranty

also applies to other engine components damaged due to the failure of any of these

emissions related components.

If a warrantable emissions related component on your engine is defective, the part will

be repaired or replaced by B&S at no cost to you including diagnosis, parts, and labor.

Warranty coverage period is five years from date of original purchase, and is offered to

the original purchaser and each subsequent purchaser so long as Owner’s Warranty

Responsibilities are adhered to.

Owner's Warranty Responsibilities:

• Warranty claims shall be filed according to the provisions of the Briggs & Stratton

Warranty Policy.

• An engine may not be warrantable if subjected to abuse, misuse, neglect, improper

maintenance, unapproved modifications, accidents not caused by Briggs & Stratton

engines or equipment, or by acts of God.

• Only those engines used as an Emergency Stationary Engine, as defined below,

are warrantable.

• Youare responsible for presenting your engine / equipment to a B&S distribution

center, servicing dealer, or other equivalent entity, as applicable, as soon as

a problem exists. The warranty repairs should be completed in a reasonable

8 vanguardpower.com

Not for

Reproduction

amount of time, not to exceed 30 days. If you have any questions regarding your

warranty rights and responsibilities, you should contact B&S at 1-800-444-7774 or

BRIGGSandSTRATTON.COM.

• If any components not scheduled for maintenance is repaired or replaced under this

warranty, the new part will be warranted only for the remaining warranty period.

• Ifa warrantable component scheduled for maintenance fails prior to its first

scheduled replacement, the part will be repaired or replaced by B&S at no charge

to the owner. Any such component is only warrantable until the originally scheduled

maintenance period has expired.

• Add on or modified parts that are not exempted by the EPA may not be used. The

use of any non-exempted add on or modified parts by the owner will be grounds for

disallowing a warranty claim. The manufacturer will not be liable to warrant failures

or warranted parts caused by the use of a non-exempted add on or modified part.

Emergency Stationary Engine Definition

AnEmergency Stationary Engine is defined as any stationary internal combustion

engine whose operation is limited to emergency situations and required testing and

maintenance. Examples include stationary engines used to produce power for critical

networks or equipment (including power supplied to portions of a facility) when electric

power from the local utility (or the normal power source, if the facility runs on its own

power production) is interrupted, or stationary engines used to pump water in the

case of fire or flood, etc. Stationary engines used for peak shaving are not considered

emergency stationary engines. Stationary engines used to supply power to an electric

grid or that supply power as part of a financial arrangement with another entity are not

considered to be emergency engines. Emergency stationary ICE may be operated for

the purpose of maintenance checks and readiness testing, provided that the tests are

recommended by Federal, State or local government, the manufacturer, the vendor,

or the insurance company associated with the engine. Maintenance checks and

readiness testing of such units is limited to 100 hours per year. There is no time limit

on the use of emergency stationary engines in emergency situations. The owner or

operator may petition the Administrator for approval of additional hours to be used for

maintenance checks and readiness testing, but a petition is not required if the owner

or operator maintains records indicating that Federal, State, or local standards require

maintenance and testing of emergency ICE beyond 100 hours per year. Emergency

stationary ICE may operate up to 50 hours per year in non-emergency situations, but

those 50 hours are counted towards the 100 hours per year provided for maintenance

and testing. The 50 hours per year for non-emergency situations cannot be used for

peak shaving or to generate income for a facility to supply power to an electric grid

or otherwise supply power as part of a financial arrangement with another entity. For

owners and operators of emergency engines, any operation other than emergency

operation, maintenance and testing, and operation in non-emergency situations for 50

hours per year, as permitted above is prohibited.

80099157(Revision A)

Not for

Reproduction

Generel information

Denne vejledning indeholder sikkerhedsoplysninger, der skal gøre dig opmærksom

på farer og risici i forbindelse med denne motor, og hvordan du forhindrer dem. Den

indeholder også instruktioner til korrekt brug og vedligeholdelse af motoren. Eftersom

Briggs & Stratton ikke ved, hvilket udstyr denne motor skal drive, er det vigtigt, at

du læser, forstår og følger disse instruktioner. Gem disse originale anvisninger til

fremtidig brug.

BEMÆRK:Figurerne og illustrationerne i denne vejledning er udelukkende til

referencebrug og kan være anderledes end din model. Hvis du har brug for hjælp,

kontakt en autoriseret serviceforhandler.

For at kunne få reservedele eller teknisk assistance skal du registrere købsdatoen samt

motorens model-, type-, trim- og serienummer. Disse numre er placeret på din motor. Se

afsnittet Funktioner og betjeningsanordninger.

Købsdato

Motormodel- Type- Trim

Motorserienummer

Kontaktoplysninger for europæisk kontor

For spørgsmål vedrørende europæisk emission bedes du kontakte vores europæiske

kontor på:

Max-Born-Straße 2, 68519 Viernheim, Tyskland.

Europæiske Union (EU) Trin V (5):

Kuldioxid-værdier (CO2)

Indtast CO2 i søgevinduet på BriggsandStratton.com for at finde kuldioxid-værdier for

Briggs & Stratton EU-typegodkendelsescertifikat for motorer.

Information om genbrug

Genbrug alle kartoner, æsker, brugt olie og batterier i

henhold til de gældende regeringsbestemmelser.

Førersikkerhed

Sikkerhedssymboler og signalord

Sikkerhedsadvarselssymbolet identificerer sikkerhedsoplysninger om farer,

der kan medføre personskader. Et signalord (FARE, ADVARSEL eller FORSIGTIG)

bliver brugt for at illustrere sandsynligheden for og den mulige grad af personskade.

Desuden bruges et faresymbol til at illustrere faretypen.

FARE indikerer en fare, som, hvis den ikke undgås, vil forårsage dødsfald eller alvorlig

personskade.

ADVARSEL indikerer en fare, som, hvis den ikke undgås, kan forårsage dødsfald eller

alvorlig personskade.

FORSIGTIG indikerer en farlig situation, som, hvis den ikke undgås, kan medføre

alvorlig eller moderat personskade.

BEMÆRK angiver oplysninger, der anses som vigtige, men som ikke vedrører farer.

Faresymboler og deres betydninger

Sikkerhedsinformation om

farer, som kan resultere i

personskade.

Læs og forstå

brugervejledningen før

brug af eller servicering af

enheden.

Brandfare Eksplosionsfare

Fare for stød Fare for giftige dampe

Fare fra varm overflade Støjfare - Høreværn

anbefales ved brug i

længere tid.

Fare for flyvende

genstande - Bær

beskyttelsesbriller.

Eksplosionsfare

Fare for forfrysning Fare for tilbageslag

Fare for amputation -

Bevægelige dele

Kemikaliefare

Fare for varme Ætsende fare

Sikkerhedsmeddelelser

ADVARSEL

Briggs & Stratton®-motorer er ikke designet til og må ikke bruges til at drive: fun-karts;

go-karts; terrængående børne-, fridtids- eller sportskøretøjer (ATV’er); motorcykler,

hovercraft; luftfartsprodukter eller køretøjer, der anvendes til konkurrenceformål, som

ikke er sanktioneret af Briggs & Stratton. For yderligere oplysninger om racingprodukter

se www.briggsracing.com. For brug med terrængående og side-by-side ATV’er kontakt

Briggs & Stratton Power Application Center, 1-866-927-3349. Forkert motorbrug kan

medføre alvorlig personskade eller dødsfald.

ADVARSEL

Benzin og benzindampe er brændbare og eksplosive. Brand eller eksplosion kan

medføre forbrændinger eller dødsfald.

Når du påfylder brændstof

• Stop motoren. Inden du fjerner brændstofdækslet, skal du vente mindst to (2)

minutter for at sikre dig, at motoren er nedkølet.

• Fyld brændstoftanken udendørs eller i et område med god luftgennemstrømning.

• Påfyld ikke for meget brændstof i tanken. Fyld ikke over bunden af brændstoftankens

hals, så der er plads til at brændstoffet kan udvide sig.

• Hold benzin væk fra gnister, åben ild, tændflammer, varme eller andre

antændelseskilder.

• Undersøg ofte brændstofledninger, brændstoftank, brændstofdæksel og tilslutninger

for revner eller lækager. Udskift beskadigede dele.

• Hvis der spildes brændstof, skal du vente, indtil det tørrer, inden du starter motoren.

Når du starter motoren

• Sørg for, at tændrør, lyddæmper, brændstofdæksel og luftfilter (hvis monteret) er

monteret korrekt.

• Prøv ikke at starte motoren med tændrøret fjernet.

• Hvis motoren er oversvømmet, skal du indstille chokeren (hvis monteret) til

positionen ÅBEN eller KØR. Flyt gashåndtaget (hvis monteret) til positionen

HURTIG, og drej, indtil motoren starter.

• Hvis der er en utæthed af natur- eller LP-gas, må motoren ikke startes.

• Da dampe er brandfarlige, må du ikke bruge startvæsker under tryk.

Når du betjener udstyret

• Vip ikke motoren eller enheden, så brændstoffet løber ud.

• Brug ikke chokeren (hvis monteret) til at stoppe motoren.

• Start, eller betjen ikke motoren, når luftfilterenheden (hvis monteret) eller luftfilteret

(hvis monteret) er fjernet.

Når du udfører vedligeholdelse

• Hvis du tømmer olien fra oliepåfyldningsrøret i toppen, skal brændstoftanken være

tom. Hvis den ikke er tom, kan der forekomme brændstoflækage, og dette kan

medføre brand eller eksplosion.

• Under vedligeholdelse, hvis det er nødvendigt at vippe enheden, skal du sørge for,

at brændstoftanken, hvis monteret på motoren, er tom, og at tændrørssiden vender

opad. Hvis brændstoftanken ikke er tom, kan der forekomme brændstoflækage, og

dette kan medføre brand eller eksplosion.

• Undersøg ofte brændstofledninger, brændstoftank, brændstofdæksel og tilslutninger

for revner eller lækager. Udskift beskadigede dele.

10 vanguardpower.com

Not for

Reproduction

• Udskift ikke regulatorfjederen, forbindelser eller andre dele for at øge motorens

hastighed.

• Undlad at slå på svinghjulet med en hammer eller hård genstand. Dette kan medføre

svigt i svinghjulet under drift.

• Reservedelene skal have samme udformning, og de skal placeres på præcist samme

måde som de originale dele. Andre dele kan medføre skade eller personskade.

Når du flytter udstyrets placering

• Sørg for, at brændstoftanken er TOM, eller at brændstofhanen er i LUKKET-stilling.

Når brændstof eller udstyr opbevares med brændstof i brændstoftanken

• Da en tændflamme eller andre antændelseskilder kan forårsage eksplosioner, skal

du holde brændstof eller udstyr på afstand af fyr, ovne, vandvarmere eller andre

enheder, der har en tændflamme.

ADVARSEL

Benzin og benzindampe er brændbare og eksplosive. Brand eller eksplosion kan

medføre forbrændinger eller dødsfald.

Motorstart medfører gnister, der kan medføre brand eller eksplosion.

• Hvis der er en utæthed af natur- eller LP-gas, må motoren ikke startes.

• Da dampe er brandfarlige, må du ikke bruge startvæsker under tryk.

ADVARSEL

FARE FOR GIFTIGE GASSER. Motorudstødning indeholder kulilte, som

er en giftig gas, der kan dræbe på få minutter. Selvom du ikke kan lugte

udstødningsgasser, kan du stadigvæk være udsat for kulilteforgiftning. Hvis du

får kvalme, føler dig svimmel eller svag, mens du bruger dette produkt, skal du

have frisk luft MED DET SAMME. Søg lægehjælp. Du kan være blevet udsat for

kulilteforgiftning.

• Kulilte kan opsamles i brugte områder. For at mindske risikoen for kuliltegas skal du

KUN bruge dette produkt udendørs og langt væk fra vinduer, døre og åbninger.

• Installer batteridrevne kuliltealarmer eller strømtilsluttede alarmer med batterisupport

som specificeret i producentens instruktioner. Røgalarmer kan ikke fornemme kulilte.

• Du MÅ IKKE betjene dette produkt indendørs i hjem, garager, kældre, krybekældre,

skure eller på andre indelukkede steder, også selvom du bruger ventilatorer eller har

åbne døre og vinduer for at sikre ordentlig ventilation. Efter brug af dette produkt kan

kulilte hurtigt samles i disse områder og forblive der i flere timer.

• Anbring ALTID dette produkt i vindretningen, og sørg for, at udstødningen peger væk

fra steder, hvor der er folk til stede.

ADVARSEL

Hurtig tilbagetrækning af startsnoren (tilbageslag) vil bevirke, at din hånd og arm

bliver trukket hurtigere mod motoren, end du kan kontrollere.Konsekvenserne

kan være brækkede knogler, skrammer eller forstuvninger.

• For at forhindre tilbageslag når du starter motoren, så træk langsomt i startsnoren,

indtil der mærkes modstand, og træk så kraftigt i den.

• Inden du starter motoren, skal du frakoble eller fjerne alt eksternt udstyr og

motorbelastninger.

• Sørg for, at direkte tilkoblede dele på udstyret, såsom, men ikke begrænset til,

skæreknive, skovlhjul, remskiver, kædehjul, er korrekt monteret.

ADVARSEL

Roterende dele kan gribe fat i hænder, fødder, hår, tøj eller tilbehør og resultere i

traumatisk amputation eller flænger.

• Betjen udstyr med sikkerhedsafskærmningerne monteret korrekt.

• Hold hænder og fødder i sikker afstand fra roterende dele.

• Fjern smykker, og sørg for, at langt hår er sat op og væk fra alle roterende dele.

• Bær ikke løstsiddende tøj eller genstande, som kan blive fanget.

ADVARSEL

Under drift bliver motoren og lyddæmperen varm. Hvis du rører ved en varm

motor, kan der opstå termiske forbrændinger.

Brændbart materiale, såsom blade, græs og krat, kan blive antændt.

• Før du berører motoren eller lyddæmperen, skal du stoppe motoren og vente to (2)

minutter. Sørg for, at motoren og lyddæmperen er sikre at røre ved.

• Fjern affald fra lyddæmperen og motoren.

Det er en overtrædelse af staten Californiens forskrifter om offentlige ressourcer, afsnit

4442, at bruge eller betjene motoren på ethvert skov-, krat- eller græsdækket område,

medmindre udstødningssystemet er forsynet med en korrekt vedligeholdt gnistfanger

som beskrevet i afsnit 4442. Andre stater eller statsretskredse har eventuelt lignende

love, se statsforskrift 36 CFR, afsnit 261.52. Kontakt en autoriseret fabrikant eller

serviceforhandler angående anskaffelse af en gnistfanger, der er konstrueret til det

udstødningssystem, der er monteret på den pågældende maskine.

ADVARSEL

Tilfældige gnister fra motoren kan forårsage elektrisk stød eller brand og kan

medføre indfiltring, traumatisk amputation eller flænger.

Før du foretager justeringer eller reparationer:

• Fjern tændrørskablet, og hold det på behørig afstand af tændrøret.

• Frakobl batterikablet fra den negative terminal (gælder kun motorer med elektrisk

start).

• Brug kun passende værktøj.

Når du tjekker for gnister:

• Brug en godkendt tændrørstester.

• Test ikke for gnister med tændrøret fjernet.

ADVARSEL

Benzindampe er brændbare og eksplosive. Brand eller eksplosion kan medføre

forbrændinger eller dødsfald.

Hvis du kan lugte gas

• Start ikke motoren.

• Tænd ikke for elektriske kontakter.

• Brug ikke en telefon i nærheden.

• Evakuer området.

• Kontakt gasforsyningen eller alarmcentralen.

Funktioner og betjeningsanordninger

Motorens betjeningselementer

Sammenlign henvisningsbogstaverne i figur 1 og 2 med motorens betjeningselementer

på den følgende liste:

A. Motorens identifikationsnumre Model-, type- og kodenummer

B. Tændrør

C. Luftfilter, lav profil

D. Oliepind

E. Oliepåfyldning

F. Oliefilter

G. Olieaftapningsprop

H. Olietrykføler

I. Luftindsugningsgitter

J. Elektrisk starter

K. Startrelæ

L. Regulator/ensretter

M. LPG/NG-blander

N. Oliekøler (hvis monteret)

O. Lyddæmper (hvis monteret)

Motorfaresymboler og deres betydninger

Motorhastighed - HURTIG Motorhastighed -

LANGSOM

Motorhastighed - STOP TÆND - SLUK

Betjening

Olieanbefalinger

Oliekapacitet: Se afsnittetSpecifikationer.

BEMÆRK

Denne motor blev leveret af Briggs & Stratton uden olie. Producenter eller forhandlere

af udstyret kan have fyldt olie på motoren. Inden du starter motoren første gang, skal

du sørge for, at olien er ved det rigtige niveau. Tilsæt olie som angivet i instruktionerne i

denne vejledning. Hvis du starter motoren uden olie, vil den blive beskadiget og vil ikke

blive repareret under garantien.

Not for

Reproduction

Vi anbefaler at bruge olie, der er certificeret af Briggs & Stratton

for at opnå den bedste

ydeevne. Andre selvrensende olier af høj kvalitet er tilladt, hvis de er godkendt til SF-,

SG-, SH-, SJ-service eller højere. Undlad at bruge specielle tilsætningsstoffer.

Brug skemaet til at vælge den bedste viskositet til det forventede

udendørstemperaturinterval. Motorer i det meste udstyr til udendørs brug kører

godt med syntetisk olie 5W-30. Til udstyr, der bruges i varmere temperaturer, yder

Vanguard

15W-50 syntetisk olie den bedste beskyttelse.

A SAE30- Under 40°F (4°C) vil brugen af SAE30 gøre det svært at starte.

B 10W-30- Over 80°F (27°C) kan brugen af 10W-30 medføre forhøjet

olieforbrug. Kontroller olieniveauet ofte.

C 5W-30

D Syntetisk 5W-30

Vanguard

syntetisk 15W-50

Kontrollér og påfyld olie

Før du tjekker eller påfylder olie

• Kontrollér, at motoren står plant.

• Rengør oliepåfyldningsområdet for affald.

• Se afsnittet Specifikationer mht. oliekapacitet.

BEMÆRK

Denne motor blev leveret af Briggs & Stratton uden olie. Producenter eller forhandlere

af udstyret kan have fyldt olie på motoren. Inden du starter motoren første gang, skal

du sørge for, at olien er ved det rigtige niveau. Tilsæt olie som angivet i instruktionerne i

denne vejledning. Hvis du starter motoren uden olie, vil den blive beskadiget og vil ikke

blive repareret under garantien.

1. Tag oliepinden ud (A, figur 3), og rengør den med en klud.

2. Sæt oliepinden i, og spænd den (A, figur 3).

3. Træk oliepinden op, og kontrollér oliestanden. Sørg for, at olieniveauet når op til

toppen af fuld-mærket (B, figur 3) på oliepinden.

4. Hvis oliestanden er for lav, skal du langsomt påfylde olie i motoroliepåfyldningen

(C, figur 3). Hæld ikke for meget olie på. Vent et minut efter oliepåfyldning, og

kontrollér oliestanden igen. Sørg for, at olieniveauet er korrekt.

5. Sæt oliepinden i, og spænd den (A, figur 3).

Beskyttelsessystem for lav oliestand (hvis

monteret)

Der er monteret en sensor for lav oliestand på nogle motorer. Hvis oliestanden er lav,

viser sensoren enten et advarselslys eller standser motoren. Stop motoren, og følg

disse trin, før du starter motoren.

• Kontrollér, at motoren står plant.

• Foretag en oliekontrol. Se afsnittet Kontrollér oliestand.

• Hvis oliestanden er lav, så tilføj den korrekte mængde olie. Start motoren, og sørg

for, at advarselslyset (hvis monteret) ikke tændes.

• Hvis oliestanden ikke er lav, må du ikke starte motoren. Kontakt en autoriseret

serviceforhandler fra Briggs & Stratton for at få rettet olieproblemet.

Anbefalet brændstof

ADVARSEL

Manglende eller defekt automatisk “brændstofafbryderventil” kan resultere i

brand eller eksplosion.

• UNDLAD at betjene udstyret i tilfælde af en manglende eller defekt automatisk

“brændstofafbryderventil”.

Brændstoffet skal overholde følgende krav

• Anvend rent, tørt brændstof, der er fri for fugt og eventuelle partikelmaterialer. Brug

af brændstoffer uden for de anbefalede grænseværdier kan forårsage problemer

med motorens ydelse.

• I motorer, der er indstillet til at drift på LPG, anbefales HD5 LPG i kommerciel

kvalitet. Den anbefalede brændstofkomposition er brændstof med minimum

brændstofenergi på 2500BTU/ft³ med maks. propylenindhold på 5% og butan og

tungere gasindhold på 2,5% og minimum propanindhold på 90%.

NG- eller LPG-motorer er certificeret til anvendelse af naturgas eller flydende

propangas. Emissionskontrolsystemet for denne motor er EM (motor modifikationer).

Påfyld brændstof

ADVARSEL

Benzindampe er brændbare og eksplosive. Brand eller eksplosion kan medføre

forbrændinger eller dødsfald.

Når du påfylder brændstof

• Fyld brændstoftanken udendørs eller i et område med god luftgennemstrømning.

• Undersøg ofte brændstofledninger, brændstoftanken og tilslutninger for revner eller

lækager. Udskift beskadigede dele.

Læs betjeningsvejledningen fra producenten for at få oplysninger om genopfyldning af

brændstof på en naturgas- eller flaskegasmotor.

Start motoren