Quick Start Guide
DIGITAL MIXER OPTION X-ADAT
High-Performance 32-Channel ADAT / Wordclock Expansion Card for X32
Table of Contents
Important Safety Instructions .........................3
FCC INFORMATION U.S.A.
..............................10
English
1. Introduction
................................................11
2. Installation
..................................................11
3. Connector Plate
.......................................... 12
4. Connection Scenarios
................................ 12
5. X32 Setup
....................................................13
Español
1. Introducción
...............................................14
2. Instalación
..................................................14
3. Placa de Conectores
................................... 15
4. Posibles Conexiones
..................................15
5. Conguración X32
..................................... 16
Français
1. Introduction
................................................17
2. Installation
..................................................17
3. Plaque Avant
............................................... 18
4. Exemples de Connexions
..........................18
5. Conguration X32
......................................19
Deutsch
1. Einleitung
....................................................20
2. Installation
..................................................20
3. Anschlussplatte
.......................................... 21
4. Anschluss-Szenarien
.................................. 21
5. X32 Einrichten
............................................22
Português
1. Introdução...................................................23
2. Instalação
....................................................23
3. Placa Conectora
..........................................24
4. Situações de Conexões
..............................24
5. X32 Instalação
............................................25
Specications
..................................................26
2 DIGITAL MIXER OPTION X-ADAT
Important Safety
Instructions
Terminals marked with
this symbol carry
electrical current of
suffi cient magnitude to constitute risk
of electric shock. Use only high-quality
professional speaker cables with ¼" TS
or twist-locking plugs pre-installed.
Allother installation or modi cation
should be performed only by
quali edpersonnel.
This symbol, wherever it
appears, alerts you to the
presence of uninsulated
dangerous voltage inside the enclosure
- voltage that may be suffi cient to
constitute a risk ofshock.
This symbol, wherever it
appears, alerts you to
important operating and
maintenance instructions in the
accompanying literature. Please read
themanual.
Caution
To reduce the risk
of electric shock,
do not remove the top cover (or the
rear section). No user serviceable
parts inside. Refer servicing to
quali edpersonnel.
Caution
To reduce the risk of re
or electric shock, do not
expose this appliance to rain and
moisture. Theapparatus shall not
be exposed to dripping or splashing
liquids and no objects lled with
liquids, such as vases, shall be placed
on the apparatus.
Caution
These service instructions
are for use by quali ed
service personnel only. Toreduce
the risk of electric shock do not
perform any servicing other than that
contained in the operation instructions.
Repairshave to be performed by
quali ed servicepersonnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus
near water.
6. Clean only with dry cloth.
7. Do not block any ventilation
openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any
heat sources such as radiators,
heat registers, stoves, or other
apparatus (including ampli ers)
that produce heat.
9. Do not defeat the safety purpose
of the polarized or grounding-type
plug. A polarized plug has two blades
with one wider than the other.
A grounding-type plug has two blades
and a third grounding prong. The wide
blade or the third prong are provided
for your safety. Ifthe provided plug
does not t into your outlet, consult an
electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly
at plugs, convenience receptacles,
and the point where they exit from
the apparatus.
11. Use only attachments/accessories
speci ed by themanufacturer.
12. Use only with
the cart, stand,
tripod, bracket, or
table speci ed by
the manufacturer,
orsold with the
apparatus. When a
cart is used, use caution when moving
the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during
lightning storms or when unused for
long periods of time.
14. Refer all servicing to quali ed
service personnel. Servicing is required
when the apparatus has been damaged
in any way, such as power supply cord
or plug is damaged, liquid has been
spilled or objects have fallen into the
apparatus, the apparatus has been
exposed to rain or moisture, does not
operate normally, or has beendropped.
15. The apparatus shall be connected
to a MAINS socket outlet with a
protective earthing connection.
16. Where the MAINS plug or an
appliance coupler is used as the
disconnect device, the disconnect
device shall remain readily operable.
17. Correct disposal of
this product: This
symbol indicates that
this product must not
be disposed of with
household waste,
according to the WEEE Directive
(2012/19/EU) and your national law.
This product should be taken to a
collection center licensed for the
recycling of waste electrical and
electronic equipment (EEE).
The mishandling of this type of waste
could have a possible negative impact
on the environment and human health
due to potentially hazardous
substances that are generally
associated with EEE. At the same time,
your cooperation in the correct disposal
of this product will contribute to the
effi cient use of natural resources.
For more information about where you
can take your waste equipment for
recycling, please contact your local city
offi ce, or your household waste
collection service.
3Quick Start Guide
Instrucciones de
seguridad
LIMITED WARRANTY
LEGAL DISCLAIMER
MUSIC Group accepts no liability for
any loss which may be su ered by
any person who relies either wholly
or in part upon any description,
photograph, or statement contained
herein. Technical speci cations,
appearances and other information
are subject to change without notice.
All trademarks are the property of
their respective owners. MIDAS,
KLARK TEKNIK, TURBOSOUND,
BEHRINGER, BUGERA and DDA are
trademarks or registered trademarks of
MUSIC Group IP Ltd. © MUSIC Group IP
Ltd. 2015 All rights reserved.
For the applicable warranty terms and
conditions and additional information
regarding MUSIC Group’s Limited
Warranty, please see complete details
online at music-group.com/warranty.
Las terminales marcadas
con este símbolo
transportan corriente
eléctrica de magnitud su ciente como
para constituir un riesgo de descarga
eléctrica. Utilicesolo cables de altavoz
profesionales y de alta calidad con
conectores TS de 6,3 mm o de bayoneta
pre jados. Cualquier otra instalación o
modi cación debe ser realizada
únicamente por un técnicocuali cado.
Este símbolo, siempre que
aparece, leadvierte de la
presencia de voltaje
peligroso sin aislar dentro de la caja;
estevoltaje puede ser su ciente para
constituir un riesgo dedescarga.
Este símbolo, siempre que
aparece, leadvierte sobre
instrucciones operativas y
de mantenimiento que aparecen en la
documentación adjunta. Por favor,
leaelmanual.
Atención
Para reducir el riesgo
de descarga eléctrica,
no quite la tapa (olaparte posterior).
Nohay piezas en el interior del equipo
que puedan ser reparadas por el
usuario. Sies necesario, póngase en
contacto con personal cuali cado.
Atención
Para reducir el riesgo
de incendio o descarga
eléctrica, no exponga este aparato a la
lluvia, humedad o alguna otra fuente
que pueda salpicar o derramar algún
líquido sobre el aparato. Nocoloque
ningún tipo de recipiente para líquidos
sobre elaparato.
Atención
Las instrucciones
de servicio deben
llevarlas a cabo exclusivamente
personal cuali cado. Paraevitar el
riesgo de una descarga eléctrica,
no realice reparaciones que no se
encuentren descritas en el manual de
operaciones. Lasreparaciones deben
ser realizadas exclusivamente por
personalcuali cado.
1. Lea las instrucciones.
2. Conserve estas instrucciones.
3. Preste atención a todas
las advertencias.
4. Siga todas las instrucciones.
5. No use este aparato cerca
del agua.
6. Limpie este aparato con un
paño seco.
7. No bloquee las aberturas
de ventilación. Instale el equipo
de acuerdo con las instrucciones
del fabricante.
8. No instale este equipo cerca de
fuentes de calor tales como radiadores,
acumuladores de calor, estufas u otros
aparatos (incluyendo ampli cadores)
que puedan producir calor.
9. No elimine o deshabilite nunca
la conexión a tierra del aparato o del
cable de alimentación de corriente.
Unenchufe polarizado tiene dos polos,
uno de los cuales tiene un contacto
más ancho que el otro. Una clavija
con puesta a tierra dispone de tres
contactos: dos polos y la puesta a
tierra. El contacto ancho y el tercer
contacto, respectivamente, son los que
garantizan una mayor seguridad. Si el
enchufe suministrado con el equipo
no concuerda con la toma de corriente,
consulte con un electricista para
cambiar la toma de corriente obsoleta.
10. Coloque el cable de suministro de
energía de manera que no pueda ser
pisado y que esté protegido de objetos
a lados. Asegúrese de que el cable de
suministro de energía esté protegido,
especialmente en la zona de la clavija y
en el punto donde sale del aparato.
11. Use únicamente los dispositivos
o accesorios especi cados por
el fabricante.
12. Use
únicamente la
carretilla,
plataforma,
trípode, soporte o
mesa especi cados
por el fabricante o suministrados junto
con el equipo. Altransportar el equipo,
tenga cuidado para evitar daños y
caídas al tropezar con algún obstáculo.
13. Desenchufe el equipo durante
tormentas o si no va a utilizarlo durante
un periodo largo.
4 DIGITAL MIXER OPTION X-ADAT
NEGACIÓN LEGAL
GARANTÍA LIMITADA
Consignes de sécurité
14. Confíe las reparaciones
únicamente a servicios técnicos
cuali cados. La unidad requiere
mantenimiento siempre que haya
sufrido algún daño, si el cable de
suministro de energía o el enchufe
presentaran daños, sehubiera
derramado un líquido o hubieran caído
objetos dentro del equipo, si el aparato
hubiera estado expuesto a la humedad
o la lluvia, si ha dejado de funcionar de
manera normal o si ha sufrido algún
golpe o caída.
15. Al conectar la unidad a la toma de
corriente eléctrica asegúrese de que
la conexión disponga de una unión
atierra.
16. Si el enchufe o conector
de red sirve como único medio
de desconexión, éste debe ser
accesiblefácilmente.
17. Cómo debe
deshacerse de este
aparato: Este símbolo
indica que este aparato
no debe ser tratado
como basura orgánica,
según lo indicado en la Directiva WEEE
(2012/19/EU) y a las normativas
aplicables en su país. En lugar de ello
deberá llevarlo al punto limpio más
cercano para el reciclaje de sus
elementos eléctricos/ electrónicos
(EEE). Al hacer esto estará ayudando a
prevenir las posibles consecuencias
negativas para el medio ambiente y la
salud que podrían ser provocadas por
una gestión inadecuada de este tipo de
aparatos. Además, el reciclaje de
materiales ayudará a conservar los
recursos naturales. Para más
información acerca del reciclaje de este
aparato, póngase en contacto con el
Ayuntamiento de su ciudad o con el
punto limpio local.
MUSIC Group no admite ningún tipo
de responsabilidad por cualquier
daño o pérdida que pudiera sufrir
cualquier persona por con ar total
o parcialmente en la descripciones,
fotografías o a rmaciones
contenidas en este documento.
Las especi caciones técnicas, imágenes
y otras informaciones contenidas
en este documento están sujetas a
modi caciones sin previo aviso. Todas
las marcas comerciales que aparecen
aquí son propiedad de sus respectivos
dueños. MIDAS, KLARK TEKNIK,
TURBOSOUND, BEHRINGER, BUGERA y
DDA son marcas comerciales o marcas
registradas de MUSIC Group IP Ltd. ©
MUSIC Group IP Ltd. 2015 Reservados
todos los derechos.
Si quiere conocer los detalles y
condiciones aplicables de la garantía
así como información adicional sobre
la Garantía limitada de MUSIC group,
consulte online toda la información en
la web music-group.com/warranty.
Les points repérés par ce
symbole portent une
tension électrique
suffi sante pour constituer un risque
d’électrocution. Utilisez uniquement
des câbles d’enceintes professionnels
de haute qualité avec ches Jack mono
6,35 mm ou ches à verrouillages déjà
installées. Touteautre installation ou
modi cation doit être e ectuée
uniquement par un personnel quali é.
Ce symbole avertit de la
présence d’une tension
dangereuse et non isolée
à l’intérieur de l’appareil - elle peut
provoquer des chocs électriques.
Attention
Ce symbol signale les
consignes d’utilisation
et d’entre ! Tienimportantes dans
la documentation fournie. Lisez les
consignes de sécurité du manuel
d’utilisation del’appareil.
Attention
Pour éviter tout risque
de choc électrique,
ne pas ouvrir le capot de l’appareil
ni démonter le panneau arrière.
L’intérieur de l’appareil ne possède
aucun élément réparable par
l’utilisateur. Laissertoute réparation à
un professionnelquali é.
Attention
Pour réduire les risques
de feu et de choc
électrique, n’exposez pas cet appareil
à la pluie, à la moisissure, auxgouttes
ou aux éclaboussures. Ne posez pas
de récipient contenant un liquide sur
l’appareil (unvase par exemple).
Attention
Ces consignes de
sécurité et d’entretien
sont destinées à un personnel
quali é. Pour éviter tout risque de
choc électrique, n’e ectuez aucune
réparation sur l’appareil qui ne soit
décrite par le manuel d’utilisation.
Les éventuelles réparations doivent
être e ectuées uniquement par un
technicienspécialisé.
1. Lisez ces consignes.
2. Conservez ces consignes.
3. Respectez tous les
avertissements.
4. Respectez toutes les
consignes d’utilisation.
5Quick Start Guide
Warning
Failure to observe the following warnings may
lead to fatality or serious injury from re or
electric shock.
Before installing the card, you must refer to the owner’s
manual of the host device or to behringer.com to verify that
your host device supports this card, and to verify the number
of cards that can be installed in combination with other
BEHRINGER or third-party cards.
• Do not attempt to disassemble or modify the card.
Donot apply excessive force to board connectors or
other board components. Mishandling of board may
lead to shock, re hazard, or equipment failure.
• Disconnect the power cable from the main unit before
installing this card to eliminate shock hazard.
Caution
Failure to observe the following precautions may
lead to personal injury, or may result in damage
to equipment or other property.
• Do not touch the board’s metallic leads (pins)
whenhandling the card. Pins are sharp and may
causeinjury.
• The card is electrostatic-sensitive.
Before handling the card, you should briey
touch the main unit’s metal casing with
your bare hand so as to drain o any static
charge from your body. BEHRINGER assumes no
responsibility for data loss, equipment damage,
or injury caused by inappropriate handling or usage.
1. IMPORTANT NOTICE: DO NOT MODIFY
THIS UNIT! This product, wheninstalled as indicated
in the instructions containedin this manual, meets FCC
requirements. Modications not expressly approved by
BEHRINGER may void your authority, granted by the FCC,
to use theproduct.
2. IMPORTANT: When connecting this product to
accessories and/or another product, use only high quality
shielded cables. Cables supplied with this product MUST be
used. Follow all installation instructions. Failure to follow
instructions could void your FCC authorization to use this
product in the USA.
3. NOTE: This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will not
result in harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in
the users manual, may cause interference harmful to the
operation of other electronic devices. Compliance with FCC
regulations does not guarantee that interference will not
occur in all installations. If this product is found to be the
source of interference, which can be determined by turning
the unit “OFF” and “ON”, please try to eliminate the problem
by using one of the following measures: Relocate either this
product or the device that is being aected by the interference.
Utilize power outlets that are on dierent branch circuits
(circuit breaker or fuse) or install AC line lters. In the case of
radio or TV interference, relocate/reorient the antenna. If the
antenna uses 300Ohm ribbon cable, use coaxial cable instead.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to distribute
this type of product. If you can not locate the appropriate
retailer, please contact BEHRINGER customer service.
FCC INFORMATION U.S.A.
10 DIGITAL MIXER OPTION X-ADAT
11Quick Start Guide
1. Introduction
The X-ADAT card is a multichannel audio interface expansion card
for the X32 series of digital mixers. It provides 32 channels of input
and output via 8 Toslink connectors and word clock transmission
via coaxial connector. The interface is perfect for recording with
standalone ADAT hard disk recorders and oers some unique
digital insert options for incorporating external processors with
ADAT connectivity.
2. Installation
Before you install the X-ADAT card in the expansion slot of the
X32 console, you must check behringer.com to verify whether the
console rmware supports that card.
Caution – before installing the X-ADAT card into the console,
you must make sure that the console’s power switch is turned o.
Malfunctions or electrical shock may occur otherwise.
1. Make sure that the mixer’s power is turned o.
2. Loosen the 2 screws left and right that fasten the slot,
then remove the slot cover or currently-installed card and
keep it in a safe place.
3. Before removing the X-ADAT card from its protective bag,
we recommend touching the grounded metal chassis of the
console to prevent electrostatic discharges aecting the
sensitive electronic components. It is generally a good idea
to hold the card either by the face plate or by the two small
handles, but never touching the components on the circuit
board directly.
4. Align both edges of the card with the guide rails inside the
slot and carefully insert the card into the slot. Push the card
all the way into the slot to ensure that the contacts of the
card are correctly inserted into the connector inside.
5. Fasten the card using the included screws. Be aware that
damage or malfunctions may occur if the card is
not fastened.
Requirements
X32 Series console with rmware version 2.0 or higher.
12 DIGITAL MIXER OPTION X-ADAT
3. Connector Plate
• Single BNC coaxial, in/output switchable,
no internal termination, LED indicates WC output
(Master mode)
• 4x Toslink inputs and 4x Toslink outputs,
8 channels per connector
• 2x small handles for removing the expansion card
from the slot
• 2x M3x6 screws left and right for fastening the card in the slot
• 3x small counter sunk screws xing the bracket on the pcb.
Do not loosen these!
4. Connection Scenarios
X-ADAT ➝ external hard disc recorder
(providing Word Clock via BNC coaxial connection)
2x ADA8200 ➝ X32 COMPACT input channels 17-24 and 25-32
Behringer X32 with X-ADAT
VIEW
VIEW
VIEWVIEWVIEWVIEWVIEWVIEW
VIEW
VIEW
VIEW
–
5
5
0
–
10
10
–
20
–
30
–
40
–
50
–
60
–
00
–
5
5
0
–
10
10
–
20
–
30
–
40
–
50
–
60
–
00
–
5
5
0
–
10
10
–
20
–
30
–
40
–
50
–
60
–
00
–
6
Hard disc recorder Recorder
Coaxial
X32 COMPACT
ADA8200
ADA8200
Optical
For synchronization
Optical
13Quick Start Guide
5. X32 Setup
X-ADAT ➝ external automixer ➝ return to X-ADAT
• Out 1-8 and 9-16 to Auto-mixing Processor inputs
• In 1-8 and 9-16 from Auto-mixing Processor outputs
• Routing/home > Input 1-16 = Card In 1-16,
Routing/card out > Output 1-16 = Local 1-16
Note, this would also apply for any other sort of specialized
outboard processing that features ADAT I/O. It can be used for
all 32 x 32 channels simultaneously, even spread over several
external processors.
Behringer X32
VIEW
VIEW
VIEWVIEWVIEWVIEWVIEWVIEW
VIEW
VIEW
VIEW
–
5
5
0
–
10
10
–
20
–
30
–
40
–
50
–
60
–
00
–
5
5
0
–
10
10
–
20
–
30
–
40
–
50
–
60
–
00
–
5
5
0
–
10
10
–
20
–
30
–
40
–
50
–
60
–
00
–
6
Auto mixer
Coaxial
Wordclock
Word clock I/O selector:
• either word clock slave (input), allowing the console to sync
to external WC devices or
• word clock master (output), providing system word clock to
other devices
X-ADAT card can be selected as the clock source on the X32 Setup/
cong page. In this case, the X32 will be slaved to the ADAT clock
received on BNC input or ber optic Toslink inputs. Note that this
may require the console to be rebooted if the internal and external
clock rates are dierent (i.e. 44.1/48 kHz).
Word clock selection box for choosing the external clock
synchronization source:
• ber optic inputs 1-4 or
• coaxial BNC WC input
• local clock indicates the X32 console’s internal clock.
26 DIGITAL MIXER OPTION X-ADAT
Specications
Connectors
TOSLINK opt. IN 4
TOSLINK opt. OUT 4
WORDCLOCK BNC IN/OUT 1
Input/Output Characteristics
Sample rates 44.1 kHz / 48 kHz
Sample word length 24 Bit
Clock synchronization selectable internal/Local
WordClock In
ADAT In 1
ADAT In 2
ADAT In 3
ADAT In 4
Round-trip latency <0.5 ms
Indicator
Master Mode (on=Clock Out, o=Clock In) 1 LED, amber
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
Responsible Party Name: MUSIC Group Services NVInc.
Address: 5270 Procyon Street
Las Vegas, NV 89118
USA
Phone Number: +1 702 800 8290
DIGITAL MIXER OPTION X-ADAT
complies with the FCC rules as mentioned in the followingparagraph:
This equipment has been tested and found to comply with the limits for a
ClassB digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the followingmeasures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician forhelp
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Important information:
Changes or modications to the equipment not expressly approved by
MUSIC Group can void the user’s authority to use the equipment.
DIGITAL MIXER OPTION X-ADAT
27Quick Start Guide
We Hear You
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
En otros idiomas
- English: Behringer X-ADAT Quick start guide