Yamaha HTR-6230 El manual del propietario

Marca: Yamaha

Modelo: HTR-6230

Categoría: Receptores AV

Tipo: El manual del propietario

HTR-6230

AV Receiver

OWNER’S MANUAL

MANUAL DE INSTRUCCIONES

Caution-i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at least

30 cm on the top, 20 cm on the left and right, and 20 cm on

the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

18 Before moving this unit, press ASTANDBY/ON to set this

unit in the standby mode, and disconnect the AC power plug

from the wall outlet.

19 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC wall outlet. Voltages are:

........................................ AC 110–120/220–240 V, 50/60 Hz

20 The batter

ies shall not be exposed to excessive heat such as

sunshine, fire or like.

21 Excessive sound pressure from earphones and headphones can

cause hearing loss.

22 When replacing the batteries, be sure to use batteries of the

same type. Danger of explosion may happen if batteries are

incorrectly replaced.

Caution: Read this before operating your unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

As long as this unit is connected to the AC wall outlet,

it is not disconnected from the AC power source even

if you turn off this unit by ASTANDBY/ON. In this

state, this unit is designed to consume a very small

quantity of power.

1 En

English

INTRODUCTION

ADDITIONAL

INFORMATION

APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Features.................................................................... 2

Supplied accessories .................................................. 2

Functional overview................................................3

Front panel ................................................................. 3

Front panel display..................................................... 4

Remote control........................................................... 5

Rear panel .................................................................. 6

Quick start guide..................................................... 7

Preparation of remote control ............................... 8

Connections ............................................................. 9

Placing speakers......................................................... 9

Connecting speakers .................................................. 9

Connecting video components................................. 11

Connecting other components ................................. 13

Using the VIDEO AUX jacks on the front panel .... 14

Connecting the FM and AM antennas ..................... 15

Connecting the power cable..................................... 15

Turning on and off the power .................................. 15

Optimizing the speaker setting for your listening

room (YPAO) .................................................... 16

Using AUTO SETUP............................................... 16

Playback.................................................................18

Basic procedure........................................................ 18

Additional operations............................................... 19

Selecting the SCENE templates ........................... 22

Selecting the desired SCENE template.................... 22

Creating your original SCENE templates ................ 24

Using remote control on the SCENE feature........... 25

Sound field programs ...........................................26

Selecting sound field programs................................ 26

FM/AM tuning ...................................................... 28

Overview.................................................................. 28

FM/AM tuning operations ....................................... 28

Preset FM/AM stations ............................................ 28

Set menu ................................................................ 30

Using set menu......................................................... 31

1 SOUND MENU .................................................... 31

2 INPUT MENU ...................................................... 33

3 OPTION MENU ................................................... 34

Remote control features ....................................... 36

Controlling this unit, a TV, or other components .... 36

Setting remote control codes.................................... 38

Advanced setup..................................................... 39

Troubleshooting.................................................... 40

Glossary ................................................................. 45

Specifications......................................................... 46

Index ...................................................................... 47

(at the end of this manual)

Contents

INTRODUCTION

PREPARATION

BASIC OPERATION

ADVANCED OPERATION

ADDITIONAL INFORMATION

APPENDIX

List of remote control codes...................................i

About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the

front panel or the ones on the remote control. In case the button

names differ between the front panel and the remote control, the

button name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications

are subject to change in part as a result of improvements, etc. In case

of differences between the manual and product, the product has

priority.

• “ASTANDBY/ON” or “fDVD” (example) indicates the name of

the parts on the front panel or the remote control. Refer to the

“Functional overview” on page 3.

2 En

INTRODUCTION

Built-in 5-channel power amplifier

(1 kHz, 0.9% THD, 6 Ω)

Front: 100 W/ch

Center: 100 W

Surround: 100 W/ch

Various input/output connectors

◆ HDMI (IN x 2, OUT x 1), Component video (IN x 3, OUT x

1), Composite video (IN x 3, OUT x 2), Coaxial digital audio

(IN x 1), Optical digital audio (IN x 2), Analog audio (IN x 9,

OUT x 2)

◆ Speaker out (5-channel), Subwoofer out

◆ Discrete multi-channel input (6-channel)

SCENE select function

◆ Preset SCENE templates for various situations

◆ SCENE template customizing capability

Sound field programs

◆ Proprietary Yamaha technology for the creation of surround

field

◆ Compressed Music Enhancer mode

◆ SILENT CINEMA™

Decoders and DSP circuits

◆ Dolby Digital decoder

◆ Dolby Pro Logic/Dolby Pro Logic II decoder

◆ DTS decoder

◆ Virtual CINEMA DSP

◆ SILENT CINEMA™

Sophisticated FM/AM tuner

◆ 40-station random and direct preset tuning

◆ Automatic preset tuning

HDMI™ (High-Definition Multimedia Interface)

◆ HDMI interface for standard, enhanced or high-definition

video (includes 1080p video signal transmission)

Other features

◆ 192-kHz/24-bit D/A converter

◆ Sleep timer

◆ Cinema and music night listening modes

◆ Remote control with preset remote control codes

Manufactured under license from Dolby Laboratories.

“Dolby,” “Pro Logic,” and the double-D symbol are

trademarks of Dolby Laboratories.

Manufactured under license under U.S. Patent No’s:

5,451,942;5,956,674;5,974,380;5,978,762;6,487,535 and

other U.S. and worldwide patents issued and pending.

DTS is a registered trademark and the DTS logos and

“HDMI,” the “HDMI” logo and “High-Definition

Multimedia Interface” are trademarks, or registered

trademarks of HDMI Licensing LLC.

“SILENT CINEMA” is a trademark of Yamaha

Corporation.

Check that you received all of the following parts.

❏ Remote control

❏ Batteries (2) (AAA, R03, UM-4)

❏ AM loop antenna

❏ Indoor FM antenna

❏ Optimizer microphone

Features

Supplied accessories

3 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

A STANDBY/ON

Turns on this unit, or sets it to standby mode (see page 15).

B PHONES jack

Connect to a pair of headphones (see page 20).

C SPEAKERS

Turns on or off the set of front speakers connected to the

FRONT A or FRONT B speaker terminals (see page 19).

D EDIT PRESET/TUNING

Switches the tuning mode (see page 28).

E A/B/C/D/E

Selects the preset station group (A to E) (see page 29).

F PRESET/TUNING l / h

Tunes into radio stations manually or automatically and selects a

preset station group (see page 28).

G BAND

Selects the reception band from FM and AM (see page 28).

H MEMORY

Stores a station that you tuned into as a preset station (see

page 28).

I TUNING AUTO/MAN’L

Selects a tuning method from automatic or manual tuning (see

page 28).

J SCENE 1/2/3/4

Recalls an input source and a sound field program assigned to

each SCENE button (see page 22).

K TONE CONTROL

Selects “BASS” and “TREBLE” to adjust frequency response

(see page 20).

L PROGRAM l / h

Selects a sound field program (see page 26).

M STRAIGHT

Activates the “STRAIGHT” mode (see page 27).

N INPUT l / h

Selects an input source (see page 18).

O NIGHT

Selects a night listening mode (see page 20).

P VOLUME control

Adjusts the volume level of this unit (see page 18).

Q VIDEO (VIDEO AUX) jack

Connects to a game console or a video camera using a

composite video cable (see page 14).

R AUDIO L/R (VIDEO AUX) jacks

Connects to a game console or a video camera using analog

audio cables (see page 14).

S PORTABLE (VIDEO AUX) jack

Connects to an audio component (such as iPod) (see page 14).

T OPTIMIZER MIC jack

Connect to the supplied optimizer microphone (see page 16).

U Front panel display

Shows information about the operational status of this unit (see

page 18).

Functional overview

Front panel

OPTIMIZER

MIC

PHONES

SILENT

CINEMA

TONE

CONTROL

PROGRAM

STRAIGHT

INPUT

VIDEO

AUDIO

PORTABLE

VIDEO

AUX

VOLUME

EFFECT

SCENE

STANDBY

/ON

NIGHT

SPEAKERS

PRESET/TUNING

EDIT

A/B/C/D/E

PRESET/TUNING

BAND

MEMORY

TUNING

AUTO/MAN'L

C D G H T

K OL N

IU PE F

J Q SB RM

4 En

Functional overview

a Decoder indicator

Lights up when any of the decoders of this unit functions.

b ENHANCER indicator

Lights up when the Compressed Music Enhancer mode is

selected (see page 26).

c VIRTUAL indicator

Lights up when Virtual CINEMA DSP is active (see page 27).

d SILENT CINEMA indicator

Lights up when headphones are connected and a sound field

program is selected (see page 27).

e Input source indicators

The corresponding cursor lights up to show the currently

selected input source.

f YPAO indicator

Lights up when you run “AUTO SETUP” and when the speaker

settings set in “AUTO SETUP” are used without any

modifications (see page 16).

g Tuner indicators

Lights up when this unit is in the FM or AM tuning mode (see

page 28).

h MUTE indicator

Flashes while the MUTE function is on (see page 20).

i VOLUME level indicator

Indicates the current volume level.

j PCM indicator

Lights up when this unit is reproducing PCM (Pulse Code

Modulation) digital audio signals.

k Headphones indicator

Lights up when headphones are connected (see page 20).

l SP A B indicators

Lights up according to the set of front speakers selected (see

page 18).

m NIGHT indicator

Lights up when you select a night listening mode (see page 20).

n CINEMA DSP indicator

Lights up when you select a sound filed program (see page 27).

o Multi-information display

Shows the name of the current sound field program and other

information when adjusting or changing settings.

p SLEEP indicator

Lights up while the sleep timer is on (see page 21).

q Input channel and speaker indicators

• LFE indicator

Lights up when the input signal contains the LFE signal.

• Input channel indicators

Indicates the channel components of the current digital input

signal.

Front panel display

DVR DVD CD

V-AUX DTV/CBL

MD/CD-R

TUNER

ENHANCER

SILENT CINEMA

NIGHT

AUTO

YPAO

PRESET

TUNED

MUTE

VOLUME

MEMORY

SLEEP

VIRTUAL

PCM

A B

LFE

LCR

SL SR

STEREO

DIGITAL

ab c d feghi

jklmnopq

LFE

LCR

SL SR

LFE indicator

Input channel indicators

5 En

Functional overview

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

a Infrared window

Outputs infrared control signals (see page 8).

b TV/AV POWER

Turns your TV or other components on or off (see page 37).

c STANDBY ( )

Sets this unit to the standby mode (see page 15).

d POWER ( )

Turns this unit on (see page 15).

e MUTE

Mutes audio output (see page 20).

f Input selector buttons

Switches the input source to each source (see page 18).

g TV control buttons

Controls your TV (see page 36).

h AMP

Press this button before you control this unit (see page 18).

i SCENE 1/2/3/4

Recalls an input source and a sound field program assigned to

each SCENE button (see page 22).

j BAND LEVEL TITLE

Selects the speaker that you want to adjust (see page 20).

k MENU

Displays the set menu on the front panel display (see page 31).

l Cursors (l / h / n / k) / ENTER

• Press cursors to navigate the set menu (see page 31).

• Press ENTER to confirm a selection in the set menu (see

page 31).

m VOLUME +/–

Adjusts the volume level of this unit (see page 18).

n RETURN

Returns the previous menu level when the set menu is displayed

(see page 31).

o DISPLAY

Displays the information of external components (such as a

DVD player) (see page 37).

p Control buttons

Control external components (such as a DVD player) connected

to this unit (see page 37).

q PROG l / h

Selects the sound field program (see page 26).

r ENHANCER

Sets the sound field program to the “Music Enh. 2ch” or “Music

Enh. 5ch” (see page 26).

s SUR.DECODE

Selects a decoder from four decoders (see page 27).

t STRAIGHT

Activates the “STRAIGHT” mode (see page 27).

u NIGHT

Selects a night listening mode (see page 20).

v MULTI CH IN

Sets the input source to MULTI CH IN (see page 19).

w AUDIO SEL

Selects an audio input select setting for each input source (see

page 19).

x SLEEP

Sets the sleep timer (see page 21).

y Numeric buttons

Enter remote control codes or preset station number (see

page 38).

Remote control

POWER

MD/CD-R

TUNER

DVD

V-AU X

BAND LEVEL

TITLE

RETURN

ENTER

REC

PROG

ENHANCER

SUR.DECODE

STRAIGHT

NIGHT

MULTI CH IN

AUDIO SEL

SLEEP

ENT

DISPLAY

VOLUME

AMP

DTV/CBL

DVR

TV CH

TV VOL

TV INPUT TV MUTE

POWER POWER

MUTE

STANDBY

D E

SCENE

2341

6 En

Functional overview

a COMPONENT VIDEO jacks

Connect to Y, PB/CB and PR/CR jacks on your video components

with component video cables (see page 11).

• DVD input jacks

• DTV/CBL input jacks

• DVR input jacks

• MONITOR OUT output jacks

b HDMI terminals

Connect to HDMI output/input terminals on your external

components with HDMI cables (see page 11).

• HDMI DVD terminal

• HDMI DTV/CBL terminal

• HDMI OUT output terminal

c VIDEO jacks

Connect to video jacks on your video components with

composite video cables (see page 11).

• DVD input jack

• DTV/CBL input jack

• DVR IN jack

• DVR OUT jack

• MONITOR OUT jack

d ANTENNA terminals

Connect to the supplied FM and AM antennas (see page 15).

e SPEAKERS terminals

Connect to each speakers (see page 9).

• FRONT A L/R

• FRONT B L/R

• SURROUND L/R

• CENTER

f DIGITAL INPUT jacks

Connect to the DIGITAL output jacks on your digital audio

components with Coaxial/Optical digital audio cables.

This input jacks support PCM, Dolby Digital and DTS bitstream

(see page 11).

• COAXIAL (DVD)

• OPTICAL (DTV/CBL)

• OPTICAL (CD)

g MULTI CH INPUT jacks

Connect to the output jacks on your multi-format player or

external decoder with analog audio cables (see page 14).

• FRONT L/R jack

• SURROUND L/R jack

•CENTER jack

• SUBWOOFER jack

h AUDIO jacks

Connect to the audio output/input jacks on your components

with analog audio cables (see page 11).

• DVD L/R jack

• DTV/CBL L/R jack

• DVR IN L/R jack

• DVR OUT L/R jack

• CD L/R jack

• IN (PLAY) L/R jack

• OUT (REC) L/R jack

i SUBWOOFER OUTPUT jack

Connect to a Subwoofer with an analog audio cable (see

page 9).

j VOLTAGE SELECTOR

Select the switch position according to your local voltage (see

page 15).

k Power cable

Connect to a standard AC outlet (see page 15).

Rear panel

DIGITAL INPUT

COMPONENT VIDEO

VIDEO

AUDIO

MULTI CH INPUT

HDMI

ANTENNA

SPEAKERS

DVD

OPTICAL

DVD

SURROUND

CENTER

FRONT B

FRONT A

DVR

SURROUND

FRONT

CENTER

SUBWOOFER

DTV/CBL

DVD

DVR

GND

OUT

DTV/CBL

DVD

DVR

OUTPUT

SUB

WOOFR

OUT

MD/

CD-R

(PLAY)

OUT

(REC)

DTV/CBL

MONITOR

OUT

MONITOR

OUT

DVD

COAXIAL

DTV/

CBL

OUT

UNBAL.

f g h i

d eb ca

7 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

The following steps describe the easiest way to operate this unit. See the related pages for details on the operation and

settings.

In these steps, you need the following items which are not

included in the package of this unit.

❏ Speakers

We recommend magnetically shielded speakers.

❏ Front speaker ..................................... x 2

At least two front speakers are required to start

playback.

❏ Center speaker ................................... x 1

❏ Surround speaker .............................. x 2

❏ Active subwoofer ................................... x 1

Select an active subwoofer equipped with an RCA

input jack.

❏ Speaker cable ......................................... x 5

❏ Subwoofer cable ..................................... x 1

Select a monaural RCA cable.

❏ DVD player .............................................. x 1

Select DVD player equipped with coaxial digital

audio output jack and composite video output jack.

❏ Video monitor ......................................... x 1

Select a TV monitor, video monitor or projector

equipped with a composite video input jack.

❏ Video cable ............................................. x 2

Select an RCA composite video cable.

❏ Digital coaxial audio cable .................... x 1

Place your speakers in the room and connect them to this

unit.

Connect your TV, DVD player or other components.

Connect the power cable and turn on this unit.

Select the component connected in the step 3 as an input

source and start playback.

Quick start guide

Step 1: Check the items

Step 2: Set up your speakers

• Placing speakers ☞P. 9

• Connecting speakers ☞P. 9

Video monitor

Front left

speaker

Center speaker

DVD player

Surround left

speaker

Surround right

speaker

Subwoofer

Front right

speaker

Step 3: Connect your components

• Connecting a TV monitor or projector ☞P. 1 2

• Connecting audio and video components ☞P. 1 3

• Connecting a multi-format player or an external

decoder ☞P. 1 4

• Using the VIDEO AUX jacks on the front panel

☞P. 1 4

• Connecting the FM and AM antennas ☞P. 1 5

Step 4: Turn on the power

Caution

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local voltage BEFORE

plugging the power cable into the AC wall outlet.

Improper setting of the VOLTAGE SELECTOR may

cause damage to this unit and create a potential fire

hazard. See page 15 for details on how to set the

VOLTAGE SELECTOR.

• Connecting the power cable ☞P. 1 5

• Turning on and off the power ☞P. 1 5

Step 5: Select the input source and start

playback

• Basic procedure ☞P. 1 8

• Selecting the SCENE templates ☞P. 2 2

• Adjusting the sound field programs ☞P. 2 6

8 En

PREPARATION

1 Take off the battery compartment cover.

2 Insert the four supplied batteries (AAA, R03,

UM-4) according to the polarity markings (+

and –) on the inside of the battery

compartment.

3 Snap the battery compartment cover back

into place.

Notes

• Change all of the batteries if you notice the following conditions:

– the operation range of the remote control decreases.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and

color.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

• Do not throw away batteries with general house waste; dispose of

them correctly in accordance with your local regulations.

• If the remote control is without batteries for more than 2 minutes,

or if exhausted batteries remain in the remote control, the contents

of the memory may be cleared. When the memory is cleared, insert

new batteries and set up the remote control code.

The remote control transmits a directional infrared ray.

Be sure to aim the remote control directly at the remote

control sensor on this unit during operation.

a Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

• To set the remote control codes for other components, see page 38.

Notes

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following types of

conditions:

– places of high humidity, such as near a bath

– places of high temperature, such as near a heater or stove

– places of extremely low temperatures

– dusty places

• To set the remote control codes for other components, see page 38.

Preparation of remote control

Installing batteries in the remote control

Using the remote control

30º 30º

Approximately 6 m (20 ft)

9 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

The speaker layout below shows the speaker setting we

recommend. You can use it to enjoy CINEMA DSP and

multi-channel audio sources.

Front left and right speakers (FL and FR)

The front speakers are used for the main source sound plus

effect sounds. Place these speakers at an equal distance

from the ideal listening position. The distance of each

speaker from each side of the video monitor should be the

same.

Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). If for some reason it is not practical

to use a center speaker, you can do without it. Best results,

however, are obtained with the full system.

Surround left and right speakers (SL and SR)

The surround speakers are used for effect and surround

sounds.

Subwoofer (SW)

The use of a subwoofer with a built-in amplifier, such as

the Yamaha Active Servo Processing Subwoofer System,

is effective not only for reinforcing bass frequencies from

any or all channels, but also for high fidelity sound

reproduction of the LFE (low-frequency effect) channel

included in Dolby Digital and DTS sources. The position

of the subwoofer is not so critical, because low bass

sounds are not highly directional. But it is better to place

the subwoofer near the front speakers. Turn it slightly

toward the center of the room to reduce wall reflections.

Be sure to connect the left channel (L), right channel (R),

“+” (red) and “–” (black) properly. If the connections are

faulty, this unit cannot reproduce the input sources

accurately.

■ 5.1-channel speaker connection

Connections

Placing speakers

60˚

30˚

80˚

Connecting speakers

Caution

• Use speakers with the specified impedance shown on

the rear panel of this unit.

• Before connecting the speakers, make sure that this

the AC power plug is disconnected from the AC wall

outlet.

• Do not let the bare speakers wires touch each other or

do not let them touch any metal part of this unit. This

could damage this unit and/or speakers.

• Use magnetically shielded speakers. If this type of

speaker still creates interference with the monitor,

place the speakers away from the monitor.

LRLR

HDMI

VIDEO

AUDIO OUTPUT

ANTENNA

SPEAKERS

DTV/CBL

SURROUND CENTER FRONT B

FRONT A

MONITOR

OUT

MD/

CD-R

SUB

WOOFER

OUT

(REC)

(PLAY)

DVR

L DVR CD

OUT

GND

UNBAL.

a b

10 En

Connections

* You can select the front speaker set from Front speakers (A) and Front

speakers (B) by pressing CSPEAKERS repeatedly. See page 19 for

details.

■ Connect speaker cables to each speaker

Cables are colored or shaped differently, perhaps with a

stripe, groove or ridge. Connect the striped (grooved, etc.)

cable to the “+” (red) terminals of your speaker. Connect

the plain cable to the “–” (black) terminals.

■ Before connecting to the SPEAKERS

terminal

A speaker cord is actually a pair of insulated cables

running side by side.

Remove approximately 10 mm (3/8”) of insulation

from the end of each speaker cable and then

twist the bare wires of the cable together to

prevent short circuits.

■ Connecting to the FRONT A terminals

1 Loosen the knob.

2 Insert the bare end of the speaker wire into

the slit on the terminal.

3 Tighten the knob to secure the wire.

■ Connecting to the FRONT B, CENTER, and

SURROUND terminals

1 Press down the tab.

2 Insert the bare end of the speaker wire into

the hole on the terminal.

3 Release the tab to secure the wire.

Speakers Jacks on this unit

a Front speaker (A) Right* FRONT A (R)

b Front speaker (A) Left* FRONT A (L)

c Surround speaker Right SURROUND (R)

d Surround speaker Left SURROUND (L)

e Center speaker CENTER

f Front speaker (B) Right* FRONT B (R)

g Front speaker (B) Left* FRONT B (L)

h Subwoofer SUBWOOFER

10 mm (3/8”)

Red: positive (+)

Black: negative (–)

Red: positive (+)

Black: negative (–)

11 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Audio jacks and cable plugs

AUDIO jacks

For conventional analog audio signals transmitted via left

and right analog audio cables. Connect red plugs to the

right jacks and white plugs to the left jacks.

COAXIAL jack

For digital audio signals transmitted via coaxial digital

audio cable.

OPTICAL jacks

For digital audio signals transmitted via optical digital

audio cables.

Notes

• You can use the digital jacks to input PCM, Dolby Digital, and DTS

bitstreams. All digital input jacks are compatible with digital signals with

up to 96 kHz of sampling frequency.

• This unit handles digital and analog signals independently. Thus audio

signals input at the digital jacks are not output at the analog AUDIO OUT

(REC) jack.

Video jacks and cable plugs

VIDEO jacks

For conventional composite video signals transmitted via

composite video cables.

COMPONENT VIDEO jacks

For component signals, separated into the luminance (Y)

and chrominance (P

B, PR) video signals transmitted on

separate wires of component video cables.

You can play back pictures by connecting your video

monitor and video source component to this unit using

HDMI connections.

At that time, audio/video signals output from the

connected component (such as DVD player etc.) are

output to the connected video monitor only when this unit

is turned on and set to the input source (DVD or DTV/

CBL).

Furthermore, available audio/video signals depend on the

specification of the connected video monitor. Refer to the

instruction manual of each connected component.

■ HDMI jack and cable plug

• We recommend using an HDMI cable shorter than 5 meters (16 feet)

with the HDMI logo printed on it.

• Use a conversion cable (HDMI jack ↔ DVI-D jack) to connect this unit

to other DVI components.

You can record the audio signal output at the AUDIO

OUT (REC) jack by using the recording components.

Note

• Check the copyright laws in your country to record from CDs, radio, etc.

Recording of copyrighted material may infringe copyright laws.

Connecting video components

Information on jacks and cable plugs

COAXIAL

DIGITAL AUDIO

AUDIO

OPTICAL

DIGITAL AUDIO

(White) (Red) (Orange)

Left and right

analog audio

cable plugs

Coaxial

digital audio

cable plug

Optical

digital

audio cable

plug

VIDEO

COMPONENT VIDEO

Y P

(Yellow) (Blue) (Red)(Green)

Composite

video cable

plug

Component

video cable

plugs

Information on HDMI™

Audio signals input at the HDMI jack are not output

from any speaker terminals but output from the

connected video monitor. To enjoy the sound from

speakers connected to this unit,

– make an analog or digital connection besides the

HDMI connection (see page 13).

– mute the volume of the connected video monitor.

Using the AUDIO OUT REC jack

COMPONENT

VIDEO

Video signal flow for MONITOR OUT

Input

Output

(MONITOR OUT)

HDMI

HDMI cable plug

12 En

Connections

Note

• If you turn off the video monitor connected to the HDMI OUT jack via a DVI connection, the connection may fail. In this case, the HDMI indicator

flashes irregularly.

Connecting a TV monitor or projector

Make sure that this unit and other

components are unplugged from the

AC wall outlets.

VIDEO

MULTI CH INPUT

DIGITAL INPUT

OUTPUT

ANTENNA

DVD

COAXIAL

OPTICAL

DTV/CBL

DTV/

CBL

SURROUND C

MONITOR

OUT

SUB

WOOFER

DVR

FRONT CENTER

SUBWOOFER

SURROUND

OUT

GND

UNBAL.

HDMI

DVDOUT DTV/CBL

COMPONENT VIDEO

DVD DTV/CBL DVR

MONITOR

OUT

MD/

CD-R

OUT

(REC)

(PLAY)

AUDIO

DVD DTV/CBL DVR CD

OUT

(or projector)

Component

video in

Video

Audio

out

HDMI

Recommended connections Alternative connections

13 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

This unit has three types of audio jacks, two types of video jacks and HDMI jacks. You can choose the connection

method depending on the component to be connected.

■ Connecting example (connecting a DVD player)

■ Jacks used for audio and video connections

Recommended connections are indicated by (*). When connecting a recording component, you need to make additional

connections for recording (signal transmission from this unit to the recording component).

• You can also use the VIDEO AUX jacks (see page 14) on the front panel

to connect an additional component.

• To confirm the positions of “jacks on this unit” in the following table,

refer to “Rear panel” in “Functional overview” on page 6.

Connecting other components

Connecting audio and video components

COMPONENT VIDEO

HDMI

VIDEO

AUDIOMULTI CH INPUT

DIGITAL INPUT

OUTPUT

ANTENNA

DVD DTV/CBL DVR

DVD

COAXIAL

OPTICAL

DTV/CBL

DTV/

CBL

DVDOUT DTV/CBL

MONITOR

OUT

MD/

CD-R

SUB

WOOFER

OUT

(REC)

(PLAY)

DVR

DVD

FRONT CENTER

SUBWOOFER

SURROUND

DTV/CBL DVR CD

OUT

MONITOR

OUT

GND

UNBAL.

Component out

Audio out

Video out

Coaxial out

HDMI out

Recommended connections Alternative connections

Make sure that this unit and other

components are unplugged from the

AC wall outlets.

Component Signal type Jacks on component Jacks on this unit

DVD player or Blu-ray

Disc player

Video HDMI out* HDMI (DVD)*

Component out COMPONENT VIDEO (DVD)

Video out (composite) VIDEO (DVD)

Audio Optical out* COAXIAL (DVD)*

Audio out (analog) AUDIO (DVD)

Set-top box Video HDMI out* HDMI (DTV/CBL)*

Component out COMPONENT VIDEO (DTV/CBL)

Video out (composite) VIDEO (DTV/CBL)

Audio Optical out* OPTICAL (DTV/CBL)*

Analog out (analog) AUDIO (DTV/CBL)

14 En

Connections

Notes

• Be sure to make the same type of video connections as those made for your TV if the video conversion is disabled. For example, if you connected your

TV to the VIDEO MONITOR OUT jack of this unit, connect other components to the VIDEO jacks.

• Check the copyright laws in your country to record from CDs, radio, etc. Recording of copyrighted material may infringe copyright laws.

• To make a digital connection to a component other than the default one assigned to each DIGITAL INPUT or DIGITAL OUTPUT jack, configure the

“INPUT ASSIGN” setting (see page 33).

• Only analog audio signals output at AUDIO OUT (REC) jack can be recorded using the recording components. Therefore Digital signals input at the

DIGITAL INPUT jacks or analog signals input at MULTI CH INPUT jacks can be output at the analog AUDIO OUT (REC) jack for recording.

This unit is equipped with 6 additional input jacks

(FRONT L/R, SURROUND L/R, CENTER and

SUBWOOFER) for discrete multi-channel input from a

multi-format player, external decoder or sound processor.

Connect the output jacks on your multi-format player or

external decoder to the MULTI CH INPUT jacks. Be sure

to match the left and right output jacks to the left and right

input jacks for the front and surround channels.

Notes

• When you select the component connected to the MULTI CH INPUT

jacks as the input source (see page 19), this unit automatically turns off

the digital sound field processor, and you cannot select sound field

programs.

• This unit does not redirect signals input at the MULTI CH INPUT jacks

to accommodate for missing speakers. We recommend that you connect a

5.1-channel speaker system before using this feature.

• The source connected to the MULTI CH INPUT jacks on this unit cannot

be recorded.

Use the VIDEO AUX jacks on the front panel to connect a

game console or a video camera to this unit. To reproduce

the source signals input at these jacks, select “V-AUX” as

the input source.

Note

• The audio signals input at the PORTABLE mini jack take priority over

the ones input at the AUDIO L/R jacks.

DVD recorder Video HDMI out* HDMI (DVR)*

Video out (composite) VIDEO (DVR IN)

Audio Audio out (analog)* AUDIO (IN (PLAY))*

Audio recording Audio in (analog)* AUDIO (OUT (REC))*

Video recording Video in (composite)* VIDEO (DVR OUT)*

CD player Audio Coaxial out* OPTICAL (CD)*

Audio out (analog) AUDIO (CD)

MD or CD recorder Audio Audio out (analog)* AUDIO (IN (PLAY))*

Audio recording Audio in (analog)* AUDIO (OUT (REC))*

Component Signal type Jacks on component Jacks on this unit

Connecting a multi-format player or an

external decoder

MULTI CH INPUT

DVD

COAXIAL

DTV/

CBL

DVD

FRONT CENTER

SUBWOOFER

SURROUND

DTV/CBL DV

Front out

Surround out

Subwoofer out

Center out

Multi-format player or

external decoder

Using the VIDEO AUX jacks on the

front panel

Caution

Be sure to turn down the volume of this unit and other

components before making connections.

15 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Both FM and AM indoor antennas are supplied with this

unit. In general, these antennas should provide sufficient

signal strength. Connect each antenna correctly to the

designated terminals.

Notes

• The AM loop antenna should be placed away from this unit.

• A properly installed outdoor antenna provides clearer reception than an

indoor one. If you experience poor reception quality, install an outdoor

antenna. Consult the nearest authorized Yamaha dealer or service center

about outdoor antennas.

• The AM loop antenna should always be connected, even if an outdoor

AM antenna is connected to this unit.

Connecting the wire of the AM loop antenna

Assembling the supplied AM loop antenna

Note

• The types of the supplied AM loop antenna is different depending on the

models.

Select the switch position (upper or lower)

according to your local voltage using a straight

slot screwdriver.

Voltages are 110-120/220-240 V AC, 50/60 Hz.

Once all connections are complete, plug the power cable

into the AC wall outlet.

Press ASTANDBY/ON (or dPOWER) to turn on

this unit.

• When you turn on this unit, there will be a 4 to 5-second delay before this

unit can reproduce sound.

Press ASTANDBY/ON (or cSTANDBY) to turn

off this unit.

Note

• In the standby mode, this unit consumes a small amount of power in

order to receive infrared signals from the remote control.

Connecting the FM and AM antennas

ANTENNA

SURR

AUDIO OUT

DVR

OUT

DVR

GND

UNBAL.

N OUT

MONITOR

OUT

MD/

CD-R

OUT

(REC)

(PLAY)

Outdoor AM antenna

Use a 5 to 10 m (16 to 32 ft)

of vinyl-covered wire

extended outdoors from a

window.

AM loop

antenna

(supplied)

Indoor FM

antenna

(supplied)

Ground

For maximum safety and minimum

interference, connect the antenna GND

terminal to a good earth ground. A good earth

ground is a metal stake driven into moist earth.

Open the

lever

Insert Close the

lever

Connecting the power cable

VOLTAGE SELECTOR (Asia and General

model only)

Caution

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local voltage BEFORE

plugging the power cable into the AC wall outlet.

Improper setting of the VOLTAGE SELECTOR may

cause damage to this unit and create a potential fire

hazard.

Connecting the AC power cable

Turning on and off the power

Turning on this unit

Set this unit to the standby mode

110V-

120V

220V-

240V

VOLTAGE

SELECTOR

16 En

This unit has the Yamaha Parametric Acoustic Optimizer (YPAO). With the YPAO, this unit automatically adjusts output

characteristics of your speakers based on speaker positions, speaker performances, and acoustic characteristics of the

room. We recommend that you first adjust the output characteristics with the YPAO when you use this unit.

• Initial settings are indicated by (*) in the following each parameter.

1 Make sure of the following check points.

Before starting the automatic setup, check the

following check points.

• All speakers and subwoofer are connected

appropriately.

• Headphones are disconnected from this unit.

• This unit is turned on.

• The connected subwoofer is tuned on and the

volume level is set to about half way (or slightly

less).

• FRONT A speakers are selected as the front

speaker system (see page 19).

• The room is sufficiently quiet.

• The crossover frequency control of the connected

subwoofer is set to the maximum.

2 Connect the supplied optimizer microphone

to the OPTIMIZER MIC jack on the front

panel.

“SETUP•••••AUTO” appears on the front panel

display.

3 Place the optimizer microphone at your

normal listening position on a flat level

surface with the omni-directional

microphone heading upward.

• We recommend that you use a tripod (etc.) to affix the optimizer

microphone at the same height as your ears would be when you are

seated in your listening position. You can use the attached screw of

a tripod (etc.) to fix the optimizer microphone to the tripod (etc.).

4 Press ll / h to select “AUTO.”

Note

• “RELOAD” or “UNDO” is available only when you have

previously run “AUTO SETUP” and confirmed the results.

5 Press lENTER to start the setup

procedure.

This unit starts the automatic setup procedure. Loud

test tones are output from each speaker during the

audio setup procedure. After all settings

(“INITIALIZING,” “WIRING/LEVEL,”

“DISTANCE,” “SIZE”) are sequentially completed,

“FINISH” appears on the front panel display.

• To cancel the automatic setup, press lk.

Optimizing the speaker setting for your listening room (YPAO)

Notes

• Be advised that it is normal for loud test tones to be

output during the “AUTO SETUP” procedure. Do not

allow small children to enter the room during the

procedure.

• To achieve the best results, make sure that the room

is as quiet as possible while the “AUTO SETUP”

procedure is in progress. If there is too much ambient

noise, the results may not be satisfactory.

Using AUTO SETUP

VOLUME

MIN

MAX

MIN MAX

CROSSOVER

HIGH CUT

Controls of a subwoofer (example)

Choice Function

AUTO* Automatically runs the entire “AUTO

SETUP” procedure.

RELOAD Reloads the last “AUTO SETUP” settings and

overrides the previous settings.

UNDO Undoes the last “AUTO SETUP” settings and

restores the previous settings.

DEFAULT Resets the “AUTO SETUP” parameters to the

initial factory settings.

Optimizer microphone

17 En

Optimizing the speaker setting for your listening room (YPAO)

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Notes

• During the automatic setup procedure, do not perform any

operation on this unit.

• We recommend that you get out of the room while this unit is in the

auto setup procedure. It takes approximately 3 minutes for this unit

to complete the auto setup procedure.

6 When all measurements are completed

successfully, “FINISH” appears on the front

panel display.

The result of the automatic setup for each speaker

appears in order on the front panel display.

• To display the result of the automatic setup again, press lk / n

repeatedly.

Notes

• If you select “RELOAD” in step 4, no test tones are output.

• If an error occurs during the “AUTO:CHECK” procedure, the

setup procedure is canceled and an error screen appears. For

details, see “If an error screen appears” on page 17.

• When this unit detects potential problems during the “AUTO

SETUP” procedure, “WARNING” and the warning messages

appear after this unit displays the result of the automatic setup. For

details, refer to the “AUTO SETUP” section in “Troubleshooting”

on page 43.

• The distance measurement result may be longer than the actual

distance depending on the characteristics of your subwoofer.

7 Press ll / h to select “SET” or “CANCEL.”

8 Press lENTER to confirm your selection.

“AUTO SETUP” appears on the front panel display.

9 Press kMENU to exit from “SET MENU.”

10 Disconnect the optimizer microphone from

this unit.

The optimizer microphone is sensitive to heat. Keep it

away from direct sunlight and do not place it on top

of this unit.

• If you change speakers, speaker positions, or the layout of your

listening environment, run “AUTO SETUP” again to recalibrate

your system.

• When you want to check the result of the automatic setup in detail

or manually adjust the parameters, use “MANUAL SETUP” (see

page 31).

■ If an error screen appears

If this unit detects the potential problems, an error

message appears on the front panel display during the

automatic setup.

For details about each error message, see the “AUTO

SETUP” section in “Troubleshooting” on page 43.

After a few seconds later, the following choices appear.

Press ll / h to select “RETRY” or “EXIT” and then

press lENTER.

■ If “WARNING” appears

When this unit detects potential problems during the

automatic setup procedure, “WARNING” appears on the

front panel display after result of each speaker. Check the

warning messages to correct your speaker settings.

Note

• Warnings differ from errors in that warnings do not cancel the automatic

setup procedure.

Press ln to display the detailed information

about the warning.

The detailed information about the warning is displayed

and the indicators of inapplicable speakers blink on the

front panel display.

• For details about each warning message, see the “AUTO SETUP” section

in “Troubleshooting” on page 43.

Choice Function

SET* Confirms the “AUTO SETUP” results.

CANCEL Cancels the “AUTO SETUP” results.

FL: 3.3m +2

The distance between the speaker

and the listening position

The result of the

adjustment of the

volume level

Speaker

FL/FR: Front left/right

C: Center

SL/SR: Surround left/right

SW: Subwoofer

Choice Function

RETRY* Starts the “AUTO SETUP” again.

EXIT Exits from the “AUTO SETUP” procedure.

PHASE REVERSED

LFE

LCR

SL SR

Flashes

18 En

BASIC OPERATION

1 Turn on external components (TV, DVD

player, etc.) connected to this unit.

2 Press CSPEAKERS repeatedly to select the

front speakers you want to use.

The respective speaker indicators lights up on the

front panel display.

3 Press NINPUT l / h repeatedly (or press

one of the input selector buttons (f)) to

select the desired input source.

The name of the currently selected input source

appears on the front panel display for a few seconds.

4 Start playback on the selected component or

select a broadcast station.

Notes

• Refer to the operating instructions for the source component.

• See page 28 for details about FM or AM tuning instructions.

• To adjust the level of each speaker, see page 20.

5 Rotate PVOLUME (or press mVOLUME +/–)

to adjust the volume to the desired output

level.

• See page 20 to adjust the level of each speaker.

• This does not affect the AUDIO OUT (REC) level.

• You can set the initial volume level and maximum volume level

(see page 33).

6 Press LPROGRAM l / h (or press hAMP

and then qPROG l / h) repeatedly to select

the desired sound field program.

The name of the selected sound field program appears

on the front panel display.

See page 22 for details about sound field programs.

Notes

• Choose a sound field program based on your listening preference, not

merely on the name of the program.

• When you select an input source, this unit automatically selects the last

sound field program used with the corresponding input source.

• Sound field programs cannot be selected when the component connected

to the MULTI CH INPUT jacks is selected as the input source (see

page 19).

• When PCM signals with a sampling frequency higher than 48 kHz are

input, this unit is automatically set to the “STRAIGHT” mode (see

page 27).

• To display information about the currently selected input source on the

front panel display, see page 21 for details.

Playback

Caution

Extreme caution should be exercised when you play

back CDs encoded in DTS. If you play back a CD

encoded in DTS on a DTS-incompatible CD player,

you will only hear some unwanted noise that may

damage your speakers. Check whether your CD player

supports CDs encoded in DTS. Also, check the sound

output level of your CD player before you play back a

CD encoded in DTS.

Basic procedure

INPUT:DVD

DVR DVD CD

V-AUX DTV/CBL

MD/CD-R

TUNER

Available input source

Currently selected input source

Movie Dramatic

Currently selected surround field program

19 En

Playback

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Use the following features to select input jack or input

source.

■ Selecting the front speaker set

Press CSPEAKERS repeatedly change the

active front speaker set that is connected to the

FRONT A or FRONT B speaker terminals or turn

off the front speakers.

The active front speaker set changes as follows:

Note

• Turn off the volume level of this unit before you switch the front speaker

setting.

■ Using the Zone B feature

When you set “FRONT B” to “ZONE B” (see page 31),

you can use the speakers connected to FRONT B speaker

terminals in another room (Zone B).

Press CSPEAKERS on the front panel

repeatedly to turn on or off the Zone B speakers.

When you activate the Zone B speakers, all the speakers in

the main room are muted.

Notes

• You cannot activate both the main room and Zone B speakers

simultaneously.

• If you select CINEMA DSP sound field program and activate the Zone B

speakers, Virtual CINEMA DSP is activated automatically (see page 27).

■ Selecting the component connected to the

MULTI CH INPUT jacks as the input source

Use this feature to select the component connected to the

MULTI CH INPUT jacks (see page 14) as the input

source.

Press NINPUT l / h repeatedly (or press

hAMP and then press vMULTI CH IN) to

select “MULTI CH.”

“MULTI CH” appears on the front panel display.

• You can configure the multi channel input settings in “MULTI CH” (see

page 34).

Notes

• Sound field programs, or the night listening mode, etc. cannot be selected

when “MULTI CH” is selected as the input source.

• When headphones are used, signals are output only from the front left

and right channels.

■ Selecting audio input jacks (AUDIO SELECT)

Use this feature (audio input jack select) to switch the

input jack assigned to an input source when two or more

jacks are assigned to an input source.

• We recommend that you set the audio input jack select to “AUTO” in

most cases.

• You can adjust the default audio input jack select of this unit by using

“AUDIO SELECT” in “OPTION MENU” (see page 35).

1 Press NINPUT l / h repeatedly (or press

one of the input selector buttons (f)) to

select the desired input source.

2 Press hAMP and then wAUDIO SEL

repeatedly to select the desired Audio input

jack select setting.

• You can configure the audio input jack select setting in “AUDIO

SELECT.”

Note

• This feature is not available if no digital input jack is assigned to

the selected input source in “INPUT ASSIGN” (see page 33).

Guide to contents

When you want... See page

Adjust the tonal quality of the front

speakers

Edit parameters of sound field

programs

Enjoy the sources which have wide

dynamic range at night

Use headphones 20

Select a decoder to play back

sources with

Set this unit to the standby mode

automatically

Additional operations

Using input setting features

FRONT A FRONT B

OFF

Choice Function

AUTO Automatically selects input signals in

the following order:

(1) Digital signals

(2) Analog signals

ANALOG Selects only analog signals. If no

analog signals are input, no sound is

output.

A.SEL:AUTO

DVR DVD CD

V-AUX DTV/CBL

MD/CD-R

TUNER

Audio input jack select setting

20 En

Playback

Use the following features to adjust the audio output or

speaker level.

■ Muting the audio output

Press eMUTE on the remote control to mute the

audio output. Press eMUTE again to resume

the audio output.

• You can also rotate PVOLUME (or press mVOLUME +/–) to

resume the audio output.

• You can configure the muting level by using “MUTE TYP.” in “SOUND

MENU” (see page 33).

• The MUTE indicator flashes on the front panel display when the audio

output is muted and disappears from the front panel display when the

audio output is resumed.

■ Adjusting the tonal quality

Use this feature to adjust the balance of bass and treble for

the front left and right speaker channels.

Press KTONE CONTROL repeatedly to select

“BASS” or “TREBLE” and then press

LPROGRAM l / h to adjust the corresponding

frequency response level.

Control range: –10 dB to +10 dB

Each choice is defined as follows.

Notes

• Speaker and headphone adjustments are stored independently.

• If you increase or decrease the high-frequency or low-frequency sound to

an extreme level, the tonal quality of the surround speakers may not

match that of the front left and right speakers.

• This does not affect recorded material.

■ Adjusting the speaker level

You can adjust the output level of each speaker while

listening to a music source. This is also possible when

playing sources input at the MULTI CH INPUT jacks.

Note

• This operation will override the level adjustment made in “SP LEVEL”

(see page 32).

1 Press hAMP and then press jBAND

LEVEL TITLE repeatedly to select the

speaker you want to adjust.

• Once you press jBAND LEVEL TITLE on the remote

control, you can also select the speaker by pressing lk / n.

• The available speaker channels differ depending on the speaker

settings.

2 Press ll / h on the remote control (or

press FPRESET/TUNING l / h) to adjust

the speaker output level.

Control range: –10.0 dB to +10.0 dB

Use the following features to utilize various useful

functions equipped on this unit.

• Initial settings are indicated by (*) in this following each parameter.

■ Using your headphones

Connect a pair of headphones with a stereo

analog audio cable plug to the PHONES jack on

the front panel.

• When you select a sound field program, SILENT CINEMA mode is

automatically activated (see page 27).

Notes

• When you connect headphones, no signals are output at the speaker

terminals.

• All Dolby Digital and DTS audio signals are mixed down to the left and

right headphone channels.

■ Selecting the night listening mode

The night listening modes are designed to improve

listenability at lower volumes or at night.

1 Press ONIGHT (or press hAMP and then

uNIGHT) repeatedly to select

“NIGHT:CINEMA” or “NIGHT:MUSIC.”

Each choice is defined as follows.

• When a night listening mode is selected, the NIGHT indicator

lights up on the front panel display.

Using audio features

Choice Function

BASS Adjusts the low-frequency response.

TREBLE Adjusts the high-frequency response.

Choice Description

FRONT L Front left speaker

FRONT R Front right speaker

CENTER Center speaker

SWFR Subwoofer

SUR.L Surround left speaker

SUR.R Surround right speaker

Using optional features

Choice Function

NIGHT:CINEMA Narrows the dynamic range of film

soundtracks and makes dialog easier to

hear at lower volumes.

NIGHT:MUSIC Preserves ease-of-listening for all

sounds.

NIGHT OFF Disables this feature.

21 En

Playback

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

2 Press ll / h to adjust the effect level while

“NIGHT:CINEMA” or “NIGHT:MUSIC” is

displayed on the front panel display.

Each choice is defined as follows.

• “NIGHT:CINEMA” and “NIGHT:MUSIC” adjustments are stored

independently.

Notes

• You cannot use the night listening modes in the following cases:

– when the component connected to the MULTI CH INPUT jacks is

selected as the input source.

– when headphones are connected to the PHONES jack.

– when the sampling frequency of the input sources are higher than 48

kHz.

• The effect of night listening modes may vary depending on the input

source and surround sound settings you use.

■ Displaying the input source information

(SIGNAL INFO)

You can display the format, sampling frequency, channel,

bit rate and flag data of the current input signal.

1 Press hAMP and then press kMENU on

the remote control.

“AUTO SETUP” appears on the front panel display.

2 Press lk / n repeatedly to select “SIGNAL

INFO” and then press lENTER.

3 Press lk / n to switch the displayed

information.

The following information about the input source

appears on the front panel display.

4 Press kMENU on the remote control again

to exit from “SET MENU.”

■ Using the sleep timer

Use this feature to automatically set this unit to the

standby mode after a certain amount of time. The sleep

timer is useful when you are going to sleep while this unit

is playing or recording from a source.

Press hAMP and then press xSLEEP

repeatedly to set the amount of time.

The sleep timer setting changes as follows.

Once the sleep timer is set, the SLEEP indicator lights up

on the front panel display, and the display returns to the

selected sound field program.

To cancel the sleep timer

Press xSLEEP on the remote control repeatedly to

select “SLEEP OFF.”

• If you set the main zone to the standby mode, the sleep timer is

automatically canceled.

■ Playing video sources in the background

You can combine a video image from a video source with

sound from an audio source. For example, you can enjoy

listening to classical music while viewing beautiful

scenery from the video source on the video monitor.

Press the input selector buttons (f) on the

remote control to select a video source and then

an audio source.

Choice Function

MIN Slightly lowers the effect level.

MID* Moderately lowers the effect level.

MAX Considerably lowers the effect level.

Choice Description

FORMAT Signal format.

SAMPLING The number of samples per second

taken from a continuous signal to

make discrete signals.

CHANNEL The number of source channels in the

input signal (front/surround/LFE).

BITRATE The number of bits passing a given

point per second.

FLAG Flag data encoded in DTS, Dolby

Digital, or PCM signals that cue this

unit to automatically switch decoders.

;AUTO SETUP

SLEEP 120min SLEEP 90min

SLEEP 60minSLEEP 30minSLEEP OFF

DVD

V-AU X

DTV/CBL DVR

CD MD/CD-R TUNER

DVD

V-AU X

DTV/CBL DVR

DVD

MULTI CH IN

Audio sources

Video sources

Audio sources

22 En

Just by pressing one SCENE button, you can recall your

favorite input source and sound field program according to

the SCENE template that has been assigned to the SCENE

button. The SCENE templates are built combinations of

input sources and sound field programs.

This unit is equipped with 12 preset SCENE templates for

various situations. The following SCENE templates are

assigned to respective SCENE buttons in the default

settings.

Notes

*1 You must connect a cable TV or a satellite tuner to this unit in advance.

See page 13 for details.

*2 You need to connect the supplied FM and AM antennas to this unit in

advance. See page 15 for details.

*3 You have to tune into the desired radio station. See pages 28 to 29 for

the tuning information.

*4 To achieve the best possible reception, orient the connected AM loop

antenna, or adjust the position of the end of the indoor FM antenna.

If you want to use other SCENE templates, you can select

the desired SCENE templates from the SCENE template

library and assign the templates to the selected SCENE

buttons on the front panel and the remote control.

1 Press and hold the desired JSCENE (or

iSCENE) button for 3 seconds.

The MEMORY indicator on the front panel starts to

flash, and the name of currently assigned SCENE

template appears on the front panel display.

2 Press NINPUT l / h (or press hAMP and

then ll / h) to select the desired template.

3 Press the JSCENE (or iSCENE) button

again to confirm the selection.

The MEMORY indicator stops flashing and the select

SCENE template is assigned to the button.

• To cancel the procedure, press hAMP and then nRETURN.

Note

• Once the desired SCENE templates are assigned to the corresponding

SCENE buttons, you may need to set the input source of the SCENE

template on the remote control. See page 25 for details.

Selecting the SCENE templates

Default SCENE

button

The name of the SCENE template and

its description

SCENE 1

DVD Movie Viewing

– input source: DVD

– sound field program: STRAIGHT

For when you want to enjoy a DVD

playback.

SCENE 2

Music Disc Listening

– input source: DVD

– sound field program: 2ch Stereo

For when you want to listen to a music disc

from the connected DVD player.

SCENE 3

TV Viewing *1

– input source: DTV/CBL

– sound field program: STRAIGHT

For when you want to watch a TV program.

SCENE 4

Radio Listening *2, *3, *4

– input source: TUNER

– sound field program: Music Enh. 5ch

For when you want to listen to a music

program from the FM radio station.

Selecting the desired SCENE template

Select the desired SCENE template

SCENE template library

(Image)

Assign the

SCENE template

to the SCENE

button

DVD Movie View

DVD Viewing

23 En

Selecting the SCENE templates

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

The following tables indicate preset SCENE template descriptions. Select the corresponding SCENE templates for the

desired source. The illustrations of the SCENE button in the following table indicate that the SCENE templates in those

cells are assigned to the SCENE buttons, respectively.

You can also create your original SCENE templates by editing the preset SCENE templates. See page 24 for details.

■ Video sources (DVD video, Recorded video)

■ Music discs (CD, SA-CD or DVD-Audio)

■ Radio programs

■ TV programs

■ Video games

Which SCENE template would you like to select?

SCENE template Input source Playback mode Features

DVD Viewing DVD STRAIGHT