Installation Instructions
Side Window Deflectors
Instruction de Montage
Deflectors sur porte
Instrucciones de Montaje
Deflectores de viento para puertas
Warning
Accessories which are not properly fitted can be daner-
ous. Read the instructions carefully before installa-
tion, and comply with the instructions at all times. If
in doubt, contact MacNeil Automotive Products Ltd.
Avertissement
Les accessoires qui ne sont pas correctement montés ris-
quent d’être dangereux. Veuillez lire soigneusement les
instructions avant d’effectuer la pose. Respectez toujours
les instructions en cours de pose. En cas de doute, con-
sultez votre concessionnaire Weathertech local.
Aviso
Aquellos accesorios que no han sido ajustados debidamente
pueden resultar peligrosos. Lea las instrucciones detenidam-
ente antes de iniciar el montaje. Durante el montaje siga las
instrucciones en todo momento. en caso de duda póngase en con-
tacto con su Concesionario de Weathertech.
Questions?
Call Customer Service @ 630-769-1500
Mon - Fri 8 AM - 5 PM
Central Daylight Time
Mild
Soap
3
Do not use
abrasives or
harsh solvents!
Clean top edge
of window.
WeatherTech® label
goes on towards the
rear of the vehicle.
1
2
La etiqueta WeatherTech® va hacia la parte de atrás.
No utilice solventes abrasivos o ásperos. Limpiar la parte de arriba de la ventana.
¼" - ½"
45
6
89
10
Ensure edge rests
on top of the outer
window sill!
Bow the
deflector
outward.
Lower windows
to the position
shown.
7
11
1
2
Pull down and
tuck in working
from front to back.
7
11
Bajar la ventana como demuestra la foto.
Asegúrese que la parte de abajo descanse arriba del
travesaño de la ventana.
Arquee el deflector de viento hacia afuera. Inserte el borde posterior dejando un
hueco en la parte superior.
Tire hacia abajo y acomódelo empezando del
frente hacia atrás.
Insert rear edge
leaving a gap at
the top.
12 13
14 15
Tips for proper fit
*Ensure that the only part of the deflector insterted into the window channel is the thin, machined flange along the
edge of the deflector.
*The bottom edge of the front deflector must must be resting on the door’s outer weatherstrip molding. See inset
of figure 5.
*Check that the thin, machined flange of each deflector is fully and evenly inserted into the window channel. The
deflector flange is designed to rest in the main window channel between the window glass and the rubber seal.
*For windows with automatic raising feature: Roll the window all the way up without activiating the automatic
feature. Leave the window all the way up for at least 12 hours. The automatic raising feature should now function
properly.
*If windows are equipped with a safety feature that automatically opens the window if any resistance is met, sim-
ply sandwich the window with your hands and push upward while raising the window. This should allow the
window to close fully. Leaving the window in the closed position for 12 hours will ensure proper functionality.
*View our installation video on line at www.WeatherTech.com/install
5X Carefully and Slowly!!
Be sure to remove
adhesive backing
before installation
if supplied!
Carefully pull
outward to seat
the deflector.
Slide upward into
place, then gently
pull outward to
seat the deflector.
Asegúrese de quitar el forro adhesivo antes de la insta-
lación, si es provisto.
Tire suavamente hacia afuera para sentar el deflector.
¡Cuidadosa y lentamente!Deslice hacia arriba para acomodarlo en su lugar, después
tire suavemente hacia afuera para sentar el deflector.
-
1
-
2
-
3
-
4
En otros idiomas
- English: WeatherTech 52433 Installation guide
Otros documentos
-
AutoVentshade 194164 El manual del propietario
-
-
AutoVentshade 194266 El manual del propietario
-
Troy-Bilt 17ARCBDW309 Manual de usuario
-
-
LG LW1812HR El manual del propietario
-
-
Troy-Bilt 17ARCACQ011 Manual de usuario