The illustrations in this manual are for reference

only. They might be different from the real tool.

Technical Data

Authorized Service Centers

Warranty Policy

ampere capability shown in the tool’s nameplate. When in doubt use the next higher gauge.

toward the rotary attachment.

• Never hold the tool by the power

cable. Hold by the housing or auxiliary handle.

• Hold the tool by the isolated parts.

The cutting tool could come into contact with hidden

wiring or its own cable. Making contact with a “live” wire

causes the metal parts to electrify and give an electric

shock to the user.

• Never let go of the power tool until the attachment

comes to a complete stop.

injuries to the user.

• Do not touch the disc or the working

piece after grinding. Wait for them to cool down. Never

try to cool them down using water or oil.

• Before checking, adjusting or

changing discs, double-check the tool is not plugged in.

• Do not use the power tool near flammable materials.

• Do not operate the tool while it is being transported to

your side.

The use of water or other liquid refrigerants can result in

an electric shock.

An abrasive disc jams into the workpiece, the edge of the

contacting disc can be pinched into the surface of the

material causing the disc to stop, creating a kickback

(sudden recoil). The disc may break and the fragments

may jump in the direction of or away from the operator,

depending on the direction of disc movement at the point

of jamming.

Kickback can occur as a result of misuse of power tools

and/or improper operating procedures or conditions and

can be avoided by taking the precautions listed below:

kickback forces if the appropriate precautions are taken;

The accessories may kick back in your hand;

This will propel the power tool in the opposite direction of

disc movement at the point of engagement or binding;

Discs that are not designed for the power tool cannot be

properly protected and are unsafe;

An improperly installed disc may project burrs outside the

plane of the guard and cannot be properly protected;

* Check backing pads for cracks, tears or excessive wear

After inspecting and installing the accessory, operate the

tool at maximum speed without charge for one minute.

Damaged accessories usually break during this periodo of

Do not use accessories that are not specifically designed

and recommended by the manufacturer. The fact that the

accessory may be installed on the power tool does not

ensure safe operation.

• Press the axis lock into the grinder head.

The axis lock should only be used to change discs.

Never use the axis lock to stop the disc while rotating.

• Connect the plug to the power inlet.

• Press the switch exactly in the pressing position (A), without releasing it,

direct the pressure forward (B) and push down slightly, release the switch to

remain locked.

• To stop operation, press in the pressing position (A) and then release

the switch.

• Work placing the disc in the right position to prevent damage.

• Press the work piece applying pressure lower than the tool’s weight to prevent

overload damaging the motor and the disc.

The angle grinder is a manual power tool used to grind and cut steel, pipes, iron angles, brick, tile, stone and / or ceramic

pieces; to remove burr on metal surfaces, to level and make smooth welding lines.

Always hold the tool with both hands. Hold the

handle with one hand and the other hand hold the

auxiliary handle. Be careful not to obstruct the

ventilation slots.

• Grinding:

Do not press, tilt or oscillate the tool. Work at a

moderate speed. The disc should always rotate

counterclockwise since there is a risk the tool shoots

out uncontrolled.

To cut hard stones using a diamond cutting disc is

• For a safer operation use the auxiliary handle.

Fit it into any of the three mounting orifices.

• Always disconnect the tool before cleaning.

• Never use water or other liquids. Use only a brush.

• To prevent the motor to overheat clean the ventilation slots regularly.

• Check all the tool components are perfectly fixed.

• The housing should not be cracked or damaged.

• Double-check the power cable is not cut or peeled.

Neatly store the tool in a dry place and protected from dust and water.

• Carbon Brushes should be periodically checked and when worn, replaced

always in a Authorized Service Center.

• After replacing the carbon brushes request to inspect if the new carbon

brushes can move freely in the carbon housing. Also request to run the tool 5

minutes to make even the contact with the carbon brushes and the commuter.

• Use only original spare carbons specifically designed

with the hardness and resistance adequate for each type of motor. Carbons

that are out of specification could damage the motor.

Almacene la herramienta ordenadamente en un lugar seco y protegida de

polvo y agua

• Desconecte siempre la herramienta antes de proceder a limpiarla.

• Nunca utilice agua u otros líquidos, solamente utilice un cepillo.

• Para evitar que se sobrecaliente el motor, debe limpiar las ranuras de

ventilación de manera regular.

• Revise que todos los componentes de la herramienta estén bien fijos.

• La carcasa no debe estar cuarteada o dañada.

• Siempre revise que el cable no esté cortado o pelado.

• Después de que hayan sido reemplazados, pida que se inspeccione si los

nuevos carbones pueden moverse libremente en el porta-carbón y solicite que

enciendan la herramienta durante 5 minutos para emparejar el contacto de los

carbones y el conmutador.

• Sólo se deben de usar carbones de repuesto originales ,

diseñados específicamente con la dureza y la resistencia eléctrica adecuadas

para cada tipo de motor. Los carbones fuera de especificaciones pueden dañar

el motor.

• Cuando se haga el cambio de carbones siempre deben reemplazarse los dos